READ AND SAVE THESE INSTRUCTIONS
WARNING: A risk of fire and electrical shock exists in all
electrical appliances and may cause personal injury or death.
Please follow all safety instructions.
Safeguards (Continued)
parts inside. Repair must be done by authorized service
personnel only.
• The mill is intended for processing small quantities of coffee beans
only for immediate consumption. This appliance is not intended to
prepare large quantities of ground coffee at one time.
• WARNING: To prevent injury from hot overflow, replace decanter
within 20 seconds, if removed during brewing. Pour slowly when
full.
• Check mill/brew chamber for presence of foreign objects before
using.
• Blades are sharp. Handle carefully.
• Do not attempt to defeat the cover interlock mechanism.
• Avoid contacting moving parts.
• Do not open Mill/Brew assembly lid until blades stop and brewing
is complete.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
CAUTION: A short power supply cord is provided to reduce the risk
of personal injury resulting from becoming entangled in or tripping
over a longer cord. Extension cords are available from local hardware
stores and may be used if care is exercised in their use. If an
extension cord is required, special care and caution is necessary. Also
the cord must be: (1) marked with an electrical rating of 125 V, and at
least 13 A, 1625 W, and (2) the cord must be arranged so that it will
not drape over the countertop or tabletop where it can be pulled on by
children or tripped over accidentally.
POLARIZED PLUG: This appliance has a polarized plug, (one blade
is wider than the other). As a safety feature to reduce the risk of
electrical shock, this plug is intended to fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
ELECTRIC POWER: If the electric circuit is overloaded with other
appliances, your appliance may not operate properly. It should be
operated on a separate electric circuit from other operating
appliances.
3
15
14
1
1
2
13
10
2
12
11
10
3
4
5
10
9
8
7
6
5
4
3
TIME
6
9
5
HR
MIN
COARS
E
FINE
10
9
SELE
CT
GRIN
D
8
7
6
5
4
6
ON
/
OFF
MILL
TIME
HR
MIN
4
3
COARSE
FINE
3
SELEC
T
GRIN
D
8
ON
/
OFF
MILL
7
FIGURE 2
FIGURE 1
8
7
6
1
2
3
5
4
FIGURE 3
FIGURE 1
MILL/BREW ASSEMBLY
FIGURE 4
FIGURE 2
1. Reservoir Cover
2. Water Window
3. Pause and Pour
4. Decanter Lid
5. Decanter
6. Cord Storage
7. Warming Plate
8. Coffeemaker Base
9. Control Panel
1. Mill/Brew Assembly Lid
2. Spreader Tube
3. Measuring Spoon
4. Motor Grinder Pin
5. Pause and Pour
6. Locking Buttons
FIGURE 3
1. Mill/Brew Basket
2. Maximum Fill Level
3. Blades
10. LED Display
11. Lock Buttons
4. Pause and Pour
5. Lock Buttons
6. Basket Tabs
7. Mill/Brew Basket Lid
8. Mill/Brew Basket Tabs
12. Mill and Brew Assembly
13. Mill/Brew Assembly Lock
14. Mill/Brew Assembly Lid
15. View Window
4
Before Using Your Mill & Brew
Coffeemaker
CAUTION: UNPLUG FROM OUTLET
COFFEEMAKER: Clean the decanter and its lid, mill/brew basket
and its lid, and mill/brew assembly. See Care and Cleaning.
Fill the coffeemaker with the maximum amount of water and no
coffee and turn the unit ON. See Brewing. Unplug coffeemaker and
discard the water. Wait 10 minutes to allow heating elements to cool.
Repeat this process one more time.
CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER
BASE IN WATER OR OTHER LIQUID.
CAUTION: BLADES ARE SHARP. DO NOT ATTEMPT TO
DISASSEMBLE MILL & BREW ASSEMBLY.
Setting the Clock
1. Set the clock for actual time of day. Press and hold “HR” button
for 2 seconds. The LED display will flash and unit will enter into
the clock-setting mode. Press “HR” and “MIN”buttons to set
correct time. Small dot in upper left corner of display signifies
A.M. No dot indicates P.M. The clock display will flash
5 times, then stop. The time is now set.
Brewing Instructions
CAUTION: DO NOT FILL MILL/BREW BASKET WITH MORE THAN
8 SPOONS OR 21⁄8 OUNCES OF COFFEE BEANS. ARROW ON
BASKET INDICATES MAXIMUM CAPACITY. DO NOT FILL
MILL/BREW BASKET WITH MORE THAN 8 SPOONS OR 23⁄4
OUNCES OF GROUND COFFEE.
1. Plug into 120V-60 Hz outlet. You do not have to set clock or timer
to brew.
2. Fill decanter with cold water and pour desired number of cups
into water reservoir. Use markings on water window to gauge
level of water required to brew desired number of 5-ounce cups.
The number 10 at the top indicates maximum 10-cup yield.
Replace decanter on warming plate.
3. Open mill/brew assembly lid and grasp mill/brew basket tabs to
remove basket lid. Place 1 measuring spoon roasted whole bean
5
Brewing Instructions (Continued)
coffee in mill/brew basket per every two cups of coffee desired.
Replace lid. Make sure basket is firmly seated in assembly, lid on
basket is secured and lid to assembly is closed before
attempting to operate unit.
NOTE: You may substitute ground coffee for coffee beans by
turning off the mill. To do so, push the Mill button. The light will
come on. Place ground coffee into mill/brew basket. Use
approximately 1 tablespoon of grounds per cup of coffee.
4. You are now ready to initiate the automatic mill and brew process.
(If you wish to use the delay timer so you can program the
coffeemaker to mill and brew later, please read section entitled
“Programming the Timer” to make coffee later.
Programming the Mill
CAUTION: DO NOT OPEN UNTIL BLADES STOP AND BREWING
IS COMPLETE. CLEAN AND DRY ALL PARTS AFTER EACH USE.
If you desire a medium grind, your machine is automatically preset to
“4” or medium grind; refer to step 2 below. If you wish to program a
finer or coarser grind, start with step 1.
1. To set the mill to grind your beans to the desired level of
coarseness, press SELECT button to select different coarseness
levels, 1-7. Seven levels of coarseness are available.
Coarseness is determined by length of time milled—the longer
the time, the finer the grind. Setting 1 will mill the beans for
15 seconds. Setting 7 will mill the beans for 40 seconds. For
medium grind, try setting 4 (if you do not select a setting, the unit
will automatically default to setting 4). Make sure mill light is off.
2. Press ON button to initiate the mill/brew process; the red ON
light will come on. Mill will start. After mill stops, unit will
automatically switch to brewing operation. To interrupt milling
or brewing, press OFF button. Red ON light will then turn off.
Do not attempt to lift mill/brew lid until operation has come to
a complete stop.
3. After brewing is complete, remove decanter from warming plate
and serve. Coffeemaker warming plate will cycle on and off to
maintain proper coffee temperature for one hour before it
automatically shuts off and the red ON light turns off.
4. Unplug and allow unit to cool for 10 minutes between cycles.
Allow to cool completely before attempting to clean.
6
Programming the Mill (Continued)
NOTE: After unit is turned off or automatically shuts off after one
hour, mill coarseness setting will default to level 4 or medium
grind. Coarseness setting will also default to level 4 in the event
of power interruption.
Programming the Timer to
Make Coffee Later
You can program the timer to automatically mill and brew coffee up to
24 hours in advance.
1. Press and hold the TIME button for 2 seconds. The green TIME
light will come on and display will read 12:00. The unit is now in
the timer programming mode.
2. Press “HR” and “MIN” buttons to program start time. Small dot
in upper left corner signifies clock is programmed for A.M. No dot
in upper left corner means clock is programmed for P.M.
3. The timer display and LED light will flash 5 times to indicate that
timer is now set. Press and release the TIME button.
The green TIME light will come on.
NOTE: If unit is operated before programmed time, timer will
need to be reset. To do this, simply depress TIME button. LED
light will come on to indicate timer has been reset.
IMPORTANT: If programming timer to future start time, make
sure water tank has been filled and mill/brew basket contains the
correct amount of beans.
Care and Cleaning
CAUTION: ALWAYS UNPLUG UNIT BEFORE CLEANING AND
ALLOW TO COOL FOR 15 MINUTES BEFORE ATTEMPTING TO
CLEAN. NEVER USE SCOURING AGENTS. NEVER IMMERSE
MACHINE IN LIQUIDS. NEVER CLEAN MACHINE UNDER
RUNNING WATER.
Decalcification of Your Mill & Brew Coffeemaker
For best tasting coffee, and to promote longer use of your Mill & Brew,
follow the procedure for decalcification every month, or after 30 uses.
If you have hard water, you may notice a slowing of the brewing
process—an indication that you should decalcify more frequently.
7
Care and Cleaning (Continued)
1. Press OFF button.
2. Unplug and allow to cool completely before cleaning.
3. Wash and dry all removable parts.
CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER
UNIT IN WATER OR OTHER LIQUID.
CAUTION: BLADES ARE SHARP. HANDLE CAREFULLY.
4. Special cleaning of the coffeemaker is recommended at least
once a month, depending on frequency of use and quality of
water. Mineral deposits can form a coating in the coffeemaker.
This may cause an off flavor in the water and may lengthen
brewing time.
5. Fill the decanter with 1 cup of vinegar and add 3 cups cold water.
Pour into water reservoir.
6. Make sure mill/brew basket and assembly are securely in place
and lid is closed.
7. Place decanter on warming plate.
8. Press ON button.
9. Halfway through brewing, press the OFF button. Carefully
remove the decanter and place on a heat resistant surface. Wait
15 minutes and pour solution back into water reservoir.
10. Press ON button. Allow all solution to empty into decanter. After
dripping stops, press OFF button and discard solution.
11. Allow coffeemaker to cool 10 minutes. Rinse it out by brewing a
decanter full of cold water. Discard water.
12. Wash, rinse and dry decanter and lid.
13. You may also use a commercial cleaner made for automatic
coffeemakers.
14. When coffeemaker has cooled, wipe exterior housing with
a damp cloth.
Any servicing requiring disassembly other than the above
cleaning must be performed by an authorized service center.
Mill & Brew Assembly
Never attempt to disassemble the grinder. If you wish to empty the
mill/brew basket to refill with different beans, pour beans out, then fill
with new beans. There will always be some ground coffee remaining
in the basket.
8
Troubleshooting Guide
• If mill/brew lid is opened during brewing cycle, ON/OFF LED will
flash. To restart brewing process, reclose mill/brew lid.
• To position or remove the mill/brew assembly, press inward on the
indentations on top of the lock buttons. Open mill/brew lid and lift
up if removing, or place into position and then release lock buttons.
If basket is properly seated and locked onto the base unit, the
mill/brew and assembly will not move.
9
NOTES
10
IMPORTANT NOTICE
If any parts are missing or defective,
DO NOT return this product.
Please call our Customer Service Department for assistance.
800-233-9054 Monday - Friday 9:00 am - 5:00 pm CST
Thank You
ONE-YEAR LIMITED WARRANTY
This Salton, Inc. product warranty extends to the original consumer purchaser of the product.
Warranty Duration: This product is warranted to the original consumer purchaser for a period
of one (1) year from the original purchase date.
Warranty Coverage: This product is warranted against defective materials or workmanship.
This warranty is void if the product has been damaged by accident, in shipment, unreasonable
use, misuse, neglect, improper service, commercial use, repairs by unauthorized personnel or
other causes not arising out of defects in materials or workmanship. This warranty is effective
only if the product is purchased and operated in the USA, and does not extend to any units which
have been used in violation of written instructions furnished by Salton, Inc., or to units which
have been altered or modified or to damage to products or parts thereof which have had the
serial number removed, altered, defaced or rendered illegible.
Warranty Disclaimers: This warranty is in lieu of all warranties expressed or implied and no
representative or person is authorized to assume for Salton, Inc. any other liability in connection
with the sale of our products. There shall be no claims for defects or failure of performance or
product failure under any theory of tort, contract or commercial law including, but not limited to,
negligence, gross negligence, strict liability, breach of warranty and breach of contract.
Warranty Performance: During the above one-year warranty period, a product with a defect will
be either repaired or replaced with a reconditioned comparable model (at Salton, Inc. option)
when the product is returned to the Salton, Inc. facility within the warranty period and an
additional one-month period. No charge will be made for such repair or replacement.
Service and Repair
Should the appliance malfunction, you should first call toll-free 1-800-233-9054 between the
hours of 9:00 am and 5:00 pm Central Standard Time and ask for CUSTOMER SERVICE
stating that you are a consumer with a problem.
In-Warranty Service (USA) for an appliance covered under the warranty period, no charge is
made for service or postage.
In-Warranty Service (Canada) for an appliance covered under the warranty period, no charge
is made for service or postage. Please return the product insured, packaged with sufficient
protection, and postage and insurance prepaid to the address listed below. Customs
duty/brokerage fee, if any, must be paid by the consumer.
Out-of-Warranty Service: A flat rate charge by model is made for out-of-warranty service.
11
Include $15.00 (U.S.) for return shipping and handling.
Salton, Inc. cannot assume responsibility for loss or damage during incoming shipment. For your
protection, carefully package the product for shipment and insure it with the carrier. Be sure to
enclose the following items with your appliance: any accessories related to your problem; your
full return address and daytime phone number; a note describing the problem you experienced;
a copy of your sales receipt or other proof of purchase to determine warranty status. C.O.D.
shipments cannot be accepted.
Return the appliance to:
ATTN: Repair Department, Salton, Inc.
550 Business Center Drive
Mt. Prospect, IL 60056
Consumer Service: 1-800-233-9054
Consumer Parts: 1-800-947-3745
Hours: 9:00 a.m. - 5:00 p.m. CST
For more information on Salton, Inc. products:
E-mail us at SALTON [email protected]
This Melitta product is distributed and serviced by Salton, Inc.
Printed in China
© 2000 Salton, Inc.
Part No. 60485
12
|