CASE 5600 series
User Manual
Configuration
(W x H x D)
Dimension
7.9" x 17.3" x 19.4"
ATX, Micro ATX
M/B Size
Drive Bay
External : 4 x 5.25" + 2 x 3.5"
Internal : 5 x 3.5"
Expansion Slots
Thermal Solution
7 Slots
1 x 12 cm fan in rear and 1 x 12 cm fan holder in front
Air Filter One air filter on the front panel ( only in R6A34)
I/O Port Bracket
Supports one I/O port bracket for standard ATX M/B
Megal Material 0.8 mm thickness SECC rustproof & galvanized JIS Steel
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
2
CASE 5600 series
User Manual
Features Descriptions
Front 120mm Fan
Rear 120mm Fan
Sliding Rails for 5.25"
device
Sliding Rails for 3.5" HDD
Screw-less Add-on Card
assembly
Door opening up to 270
Degree
Easy-clean filter
(in left side panel)
Easy-clean filter
(in front panel)
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
3
CASE 5600 series
User Manual
Screw-less and lockable
left side panel
Adjustable air inflow
Front IO Ports
Convenient Accessory box
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
4
CASE 5600 series
User Manual
Installation
1.Opening Chassis
1.1
1.3
1.4
Take off the thumb screws on the back plane
1.2
Roll the side cover anticlockwise to open
Push hooks marked in red circle to detach the
front panel from the chasis
Push the Key-button
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
5
CASE 5600 series
User Manual
2.Installing Motherboard
ATX Motherboard
Special motherboard stand-off
2.2
2.1
Sit the motherboard on our special
motherboard stand-off and screw in all the
screws into the motherboard stand-offs.
Due to our special design of
motherboard stand-off,copper
motherboard stand-off not needed
when you install the ATX motherboard.
NOTE : The copper motherboard stand-off not
needed when you install the ATX motherboard.
DON'T SCREW THE COPPER MOTHERBOARD
STAND-OFF INTO THE SPECIAL MOTHERBOARD
STAND-OFF OR MOTHERBOARD INSTALLING
CAN'T BE PROCESSED SUCCESSFULLY.
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
6
CASE 5600 series
User Manual
Micro ATX Motherboard
2.1
2.2
Locate and align the screw holes on the
motherboard and chasis; place the
motherboard at the correct position,
and then screw copper motherboard stand-
offs brass studs onto chassis's metal shell.
Sit the motherboard on themotherboar
stand-offs and screw in all the screws
into the motherboard stand-offs.
Note: Screw holes marked with "M" are
motherboard stand-off positions for micro
ATX motherboard.
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
7
CASE 5600 series
User Manual
3.Installing 3.5" HDD
3.1
3.2
3.3
Insert the screw into the rubber pad hole on the rail
Attach rails to bothe sides of
your HDD
Insert the railed HDD into the 3.25" HDD bay and push to the buttom
NOTE : Screws for HDD have no
thread, no screwdriver needed
when you work step 3.2
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
8
CASE 5600 series
User Manual
4.Installing 5.25" Device
4.1
4.3
Disassemble the front panel (please refer to step 1.4 )
4.2
Insert the railed 5.25" device into the 5.25"
drive bay
Attach rails to both sides of your 5.25" device
PS: You can also fasten rails on your 5.25" device by screws
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
9
CASE 5600 series
User Manual
5.Installing Add on Card
5.1
5.2
5.3
Push out to loosen add on card kit
Insert your add on card into the right slot
Push down add on card kit to fasten the add
on card
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
10
CASE 5600 series
User Manual
6.Installing Floppy
6.1
6.2
6.3
6.4
Detach the front panel
(Please refer to Step 1.4, Page 5)
Unscrew the screws holding the
floppy cage
Slide out the floppy cage
Remove the metal cover
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
11
CASE 5600 series
User Manual
6.5
6.6
6.7
6.8
Attach the front panel
Secure the floppy on cage by
screws
Slide the floppy cage back
Secure the floppy cage by
screws
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
12
CASE 5600 series
User Manual
7.Cleaning Filters - Air Guide Filter
8.Cleaning Filters - Front panel Filter
7.1
8.1
8.2
Turn anticlockwise to take off the filter
Push front panel hooks to detach
the front panel from the chassis
( please refer to step 1.4 )
Detach the filter from the front
panel
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
13
CASE 5600 series
User Manual
9.USB Port
NOTE :
1.Make sure that your motherboard offers USB interface. NOT every motherboard offers it.
2.NEVER connect a IEEE1394 connector to the USB pins. It will damage the motherboard.
9.1 Read your motherboard’s user manual to find the pins for the USB connector.
9.2 Find the USB connector and connect it to the pins.
M/B USB PINS
USB+5V
USB_P5 -
USB_P5 +
GND
USB+5V
USB_P8 -
USB_P8 +
GND
ON
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
14
CASE 5600 series
User Manual
10.IEEE1394 Port
NOTE :
1.Make sure that your motherboard offers IEEE1394 interface. NOT every motherboard offers it.
2.NEVER connect a USB cable to the IEEE1394 connectors. It will damage the motherboard.
10.1 Read your motherboard’s user manual to find the pins for the IEEE1394 connector.
10.2 Find the IEEE1394 connector and connect it to the pins.
M/B IEEE1394 PINS
GND
+12V
TPB2
GND
TPA2
TPA2+
GND
TPB2+
+12V
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
15
CASE 5600 series
User Manual
11.Audio Port
NOTE :
Make sure that your motherboard offers Audio interface for front panel. NOT every motherboard offers it.
10.1 Read your motherboard’s user manual to find the pins for the Audio connector.
10.2 Find the Audio connector and connect it to the pins.
M/B Audio PINS
MIC2
MICPWR
Line out_R
NC
AGND
+5VA
Bline_out_R
Line out_L
Bline_out_L
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
16
CASE 5600 series
User Manual
12.System Control Connectors
1. Read your motherboard’s user manual to find the pins for these system control connectors.
2. Refer to your motherboard’s user manual to connect these connectors correctly.
System Warning Speaker
SPEAKER
PLED
ATTENTION :
ATX Power Switch
Reset Switch
The diagram is just an example.
NOT every motherboard has the same
layout of these system control pins.
Please refer to your motherboard
user’s manual to check the layout
before the installation.
IDE_LED
RESET
PWR
System Power LED
HDD Activity LED
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
17
CASE 5600 series
User Manual
Thank you for purchasing a High-Quality Rosewill Product.
Please register your product at : www.rosewill.com
for complete warranty information and future support for your product.
If you have any question while using our products, please visit our website : www.rosewill.com
for latest driver & user manual or feel free to contact us at [email protected]
Support Phone Number: 800-575-9885
Support Email: [email protected]
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
18
|
