Important notes for users in the U.K.
&
%
AJ3231
Clock Radio
^
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type
of plug proceed as follows:
Register your product and get support at
@
!
#
1
2
3
Remove fuse cover and fuse.
Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type.
Refit the fuse cover.
0
User manual
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distributi-
on board should not be greater than 5 Amp.
4
Note: The severed plug must be disposed of to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral
(N), brown = live (L). As these colours may not correspond with the colour mar-
kings identifying the terminals in your plug, proceed as follows:
•
•
•
Connect the blue wire to the terminal marked N or coloured black.
Connect the brown wire to the terminal marked L or coloured red.
Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
9
7
3
2
1
Before replacing the plug cover, make certain that the cord grip is clamped over
the sheath of the lead - not simply over the two wires.
8
$
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956
and The Performer’s Protection Acts 1958 to 1972.Protection Acts 1958 to 1972.
6
5
INSTALLATION
POWER SUPPLY
English
Meet Philips at the Internet
Congratulations on your purchase and welcome to Philips!
To fully benefit from the support that Philips offers, register your product at
1
Check if the mains supply, as shown on the type plate located on the
bottom of the set, corresponds to your local mains supply. If it does not,
consult your dealer or service centre.
CONTROLS
2
3
Connect the mains lead to the wall socket.
To disconnect the set from the mains supply completely, remove the plug from
the wall socket.
1 ALARM 1, ALARM 2
–
–
–
RADIO activates the radio for alarm 1 or alarm 2
BUZ activates the buzzer for alarm 1 or alarm 2
OFF switches off the alarm 1 or alarm 2
CLOCK MEMORY BACKUP
2 Clock control
The clock memory backup allows your alarm and clock time settings to be stored
for up to a day when there is a power interruption e.g. mains failure. The com-
plete clock radio and display illumination will be switched off. As soon as the
mains supply returns, the display will indicate the correct time.
- SET TIME : sets the clock time
- CLOCK: to run on clock time
- SET AL 1: sets the alarm time for alarm 1
- SET AL 2: sets the alarm time for alarm 2
3 UP / DOWN: adjusts the hours/ minutes for the clock and alarm times
4 DISPLAY - show the clock/ alarm times and status of the set
5 Battery door - opens to store a 9 volt 6F22 type battery (not included) for
clock memory backup
1
Remove the battery door to insert a 9 volt 6F22 type battery (not included) for
backup.
2
Replace the battery door.
NOTE: If no backup battery is installed or the power interruption is prolonged, you
will need to set the clock and alarm times again.
Batteries contain chemical substances so should be disposed of
properly.
6 VOL - adjusts the sound level
7 Frequency indicator - shows the radio frequency of your selected waveband
8 BAND (MW/FM/AUX) - select MW/FM waveband or switch to the AUX source
9 TUNING - tunes to radio stations
For users in the U.K.: please follow the instructions on the reverse of this
sheet.
The type plate is located on the bottom of the set.
0 REPEAT ALARM (SLEEP OFF)
-
-
switches off the active alarm for a 6-7 minute period
switches off the radio sleep function
W
Printed in China
! SLEEP - activates the radio for sleep function
-
adjusts the sleep period
AJ3231
ILLUMINATION BRIGHTNESS
@ ALARM RESET - stops the active alarm for 24 hours
# RADIO ON/OFF - switches the radio on/off
$ BRIGHTNESS - changes the brightness of the display illumination
% Mains lead - for AC mains supply
Adjust the BRIGHTNESS switch to HI or LO
– HI to increase the brightness
– LO to select low illumination
^
Pigtail aerial
-
improves FM reception
AJ3231_05_UM_V4.1
&
AUX connects external audio source.
-
|