ii
Contents
Getting Started
Fitting and removing the battery
Before removing the battery, ensure that the phone is switched off and the charger
is disconnected from the phone.
Fitting the battery — A100
1
2
1
2
Remove the battery compartment cover. Insert the battery ensuring the
3 gold contacts align with the 3 gold pins in the phone. When replacing
the cover, ensure to slide upward to the top of the phone.
Removing the battery — A100
1
2
Push and hold the release latch ➊ towards the top of the phone using
the cover clip, then lift the battery out ➋.
Getting Started
1
Fitting the battery — A101
Remove the battery compartment cover. Insert the battery ensuring the
3 gold contacts align with the 3 gold pins in the phone. When replacing
the cover, ensure to slide upward to the top of the phone.
Removing the battery — A101
1
Push and hold the release latch ➊ towards the top of the phone using
the cover clip, then lift the battery out ➋.
2
Getting Started
Fitting and removing the SIM
The SIM is located under the battery.
Fitting the SIM — A100
Removing the SIM — A100
Ensure the gold contacts are facing
downwards before sliding the SIM
into the SIM holder.
While holding the tab down, slide
the SIM out.
Fitting the SIM — A101
Removing the SIM — A101
Ensure the gold contacts are facing
downwards before sliding the SIM
into the SIM holder.
While holding the tab down, slide
the SIM out.
Charging the battery
Connecting and disconnecting the Travel Charger
The battery must be fitted in the phone before the charger is connected. Insert the
Charging Connector into the socket at the base of the phone before connecting the
Getting Started
3
charger to the mains outlet. Once connected, the Battery level indicator will start
battery for a minimum of 4 hours before first use.
NOTE: DO NOT force the connector as this may damage the phone and/or the charger.
If the battery has been deeply discharged, it may take several minutes before the Battery
level indicator is displayed.
When charging is complete,
disconnect the charger from
the outlet before removing the
plug from the phone.
Battery level indicator
While charging
Charging
complete
Phone on
Phone off
>J
Low battery power warning
When the battery power is low, a “Battery is Low” message will be displayed. If this
occurs during conversation, finish your call immediately. The power will
automatically switch off after the warning tone. Fully recharge the battery. See
is charging.)
4
Getting Started
Your phone — A100
Earpiece
Personal
Hands Free Connector
Display
Navigation Key
Scroll/move through
menus
Right Soft Key
Cancel/exit
Perform functions
indicated in the right
display corner
Left Soft Key
Perform functions
indicated in the left
display corner
Send Key
Power/End Key
Press and hold to switch
your phone on/off
Answer/make a call
Silent Mode Key
Press and hold to switch
Silent Mode on/off
Charging Connector
Getting Started
5
Your phone — A101
Earpiece
Personal
Hands Free Connector
Display
Navigation Key
Scroll/move through
menus
Right Soft Key
Cancel/exit
Perform functions
indicated in the right
display corner
Left Soft Key
Perform functions
indicated in the left
display corner
Send Key
Answer/make a call
Power/End Key
Press and hold to switch
your phone on/off
Silent Mode Key
Press and hold to switch
Silent Mode on/off
Charging Connector
6
Getting Started
Key functions
A100 Key
A101 Key
Function
Navigation Key: Scroll or move through menus, text and
phone numbers.
In idle mode, press to display the “Contacts” menu.
4
4
Left Soft Key: Perform the functions displayed in the
lower left corner.
In idle mode, press to activate the “Menu” display, or press
and hold to activate the “Profiles” menu.
A
@
A
Right Soft Key/Cancel or Exit Key: Perform the
functions displayed in the lower right corner. Mainly used
to cancel and return to the previous menu level.
In text entry mode, press to delete text.
In idle mode, press and hold to activate the “Messages”
menu.
@
When receiving a call, press to mute the ringtone.
Numeric Keys: Enter numbers. Press and hold one of the
keys from $ to , for Hotkey dialling.
Press and hold # to enter a “+” (international access
code) or “P” (extension number code).
#~, #~,
To dial an extension number, dial the phone number first,
press and hold # to add a “P”, then enter the extension
number.
"
"
In text entry mode, enter text, numbers and characters.
Send Key: Make a call or answer a call.
In idle mode, press to check the last dialled list.
In text entry mode, press to switch between input
methods.
C
D
!
C
D
!
Power/End Key: End/reject a call.
During key operation, press to return to the previous display.
Press and hold to return to idle mode.
In idle mode, press and hold to switch phone on/off.
Silent Mode Key: In idle mode, press and hold to switch
the Silent Mode (Vibrator on/Ring off) on and off.
In text entry mode, press to switch T9 smart English input
mode on/off, or press and hold to enter symbols.
Getting Started
7
During a call
Minimal menu options are available during a call by pressing the following key
options.
A100 Key
A101 Key
Function
Activate Hands free, Conference call, Call transfer,
Contacts list, Messages menu, Call status.
A
A
Swap between two calls. Put the call on hold.
Increase the volume while on a call.
Decrease the volume while on a call.
@
1
@
1
5
5
Display the last dialled records list. Answer another call. If
a phone number is entered, hold the active call and call the
number.
C
C
Send DTMF.
#~,
#~,
Press and hold ! to switch the Hands free speaker
on/off
!"
!"
8
Getting Started
Displays
Idle display
The clock appears on the display one minute after you press
the last key.
The clock position changes every minute.
NOTE: All screen images in this manual are simulated.
NOTE: Some services described in this manual are network
dependent or may only be available on a subscription basis. Some
functions are SIM dependent.
For more information, contact your service provider.
Getting Started
9
Status icons
The status icons are displayed or animated according to the currently activated
functions. The Antenna, Signal and Battery icons are displayed when the handset
is switched on and connected to a network. If there is no connection with the
network, the Signal icon will not be displayed.
Icon
Meaning
Antenna and signal strength
OP
Registered to a non-home network – roaming
Call Diverts is on
G
Key Guard is enabled
Message area is full
Unread message is stored
L
(Flashing)
Voice mail indicator (voice mail has been received)
N
Alarm is set
All tones or ring volume is off
Vibrator is on
Battery charge level
Low battery
J
10
Getting Started
Symbols in the Manual
A100
A101
Meaning
Symbols
Symbols
154
Press the Navigation Key in the direction indicated by
the arrow
154
A
@
Press Left Soft Key
Press Right Soft Key
A
@
#~,
#~,
C
Press numeric Keys
Press Send Key
C
D
"
D
Press Power/End Key
Press Asterisk Key
"
!
Press Silent Mode Key
!
Symbols used throughout the manual are based on the A100.
Getting Started
11
Basic Operations
Switching the phone on/off
1. Press and hold D for 2 to 3 seconds
2. The phone starts in idle mode
3. Press and hold D again to switch the power off
Making a call
Ensure that the signal strength meter shows network
coverage is available in the current area.
To make a call, start in idle mode.
Standard dialling
1. Enter the area code and phone number C
The dialled number is displayed
2. When the other party answers, talk into the Microphone
Earpiece Volume:
During a call, 4 to adjust the earpiece volume
Using the contacts list
1. 4 to enter Contacts
2. 4 required name or phone number C
Last number dialling
1. C
2. 4 required name or phone number C
12
Basic Operations
International dialling
The international access code (+) and the destination
country/region code should be entered, followed by the area
code and phone number.
1. Press and hold # until “+” is displayed, then enter the
country / region code
2. Enter the area code and phone number C
NOTE: Many countries/regions include an initial “0” in the area
code. This should, in most cases, be omitted when dialling
international numbers. If you have difficulties making international
calls, contact your service provider.
Emergency call
To make an emergency call, the antenna (
) must be present
When SIM is inserted:
Enter the emergency number 112 C
When SIM is not inserted:
Enter the emergency number 112 C
OR
@ (SOS) > “Emergency call” A (Yes)
NOTE: Most countries support the international emergency
number 112. If you find the number does not work on your phone,
please call your service provider. Emergency calls without a SIM is
country or network operator dependent.
Ending a call
To hang up, D
The duration of the call will be displayed.
When the “Max cost” is on, the remaining units will be
displayed.
58.
Basic Operations
13
Answering a call
C
OR
If “Any key answer” is on,
From idle mode
press any key except D.
Volume:
From My Phone
1. 4 Sounds >Volume A(Select)
2. 4 Adjust the volume level A(OK)
Quick touch silent mode:
To quickly set the ringtone off (
on ( ), press and hold !.
) and the vibrator
To resume, press and hold ! again.
One click mute on incoming call:
To set the ring tone off,
@(Mute)
•If you want to reply to the call, A(Reply)
•If you want to reject the call, @(Reject).
Reject incoming call:
D
14
Basic Operations
In-call operations
During a call, the following options are available by pressing
A(Menu) or @(Hold)
Hands free/Hand held
You can switch the phone between hands free and hand
held.
During a call:
1. A(Menu)
2. 4 Hands free / Hand held A(Select)
Contacts
You can access your Contacts list that is stored in SIM in
your phone.
During a call:
1. A(Menu)
2. 4 Contacts A(Select)
Messages
You can create, check, or send a message while on a call.
During a call:
1. A(Menu)
2. 4 Messages A(Select)
Basic Operations
15
Hold
You can put a call on hold.
During a call:
@(Hold)
To resume:
A(Back)
NOTE: This function is network dependent.
Making a second call
During a call:
1. Enter the second phone number or select a phone
number from the Contacts list (see “Contacts” on page
15).
2. C The first call is put on hold
NOTE: This function is network dependent.
16
Basic Operations
Incoming call while on a call
This function is network dependent.
During a call, you may receive another call.
1. To answer another call, C (First call is placed on
hold.)
To disconnect another call, A(Reject)
2. During a conversation with a second caller, @(Swap)
or A(Menu) and select one of the following options:
Conference
You can make a conference call with up to 5 parties
During a call:
1. A(Menu)
2. 4 Conference A(Select)
NOTE: This function is network dependent.
Call transfer
Call transfer connects the active calling party to the other
party on hold, then disconnects your line, leaving the two
callers in the conversation.
During a call:
1. A(Menu)
2. 4 Call transfer A(Select)
NOTE: This function is network dependent.
Call status
Call status allows you to disconnect the line or put a call on
hold with the active party.
During a call:
1. A(Menu)
2. 4 Call status A(Select)
Basic Operations
17
Swap
When you are connected to two calls, you can switch to the
other calls.
During a call:
@(Swap) to change to the other call.
DTMF
DTMF can be sent during a conversation. These are often
used to access voice mail, paging and computerised home
banking. For example, you may need to enter a number to
remotely access voice mail messages. A phone number may
be stored in the Contacts together with a DTMF sequence,
allowing the number to be dialled upon recall and the DTMF
number to be sent automatically.
Send DTMF during a call:
Enter digits (#~,, ! or ").
Pause dial
Using pauses allows you to send DTMF automatically.
1. Enter the phone number
2. Press and hold # until a “P” is displayed at the end of
the phone number entered
3. Enter DTMF digits after the pause, e.g. enter the number
to access voice mail messages
4. C
When the call is connected the DTMF sequence will be
sent after 3 seconds.
18
Basic Operations
Text entry
You can use alphanumeric characters to enter details into the Contacts list, to
create text, etc.
Text mode
Numeric
Multi tap
(Input mode indicator:
Abc, abc or ABC)
®
Key
T9 (T9Abc, T9abc, T9ABC)
(Input language: English)
(0 ~ 9)
Space 0. , ? ! + - = : ¿ ¡ ” ’ ; _
0
1
2
3
4
5
6
7
8
9
#
$
%
&
'
(
)
*
+
,
C
"
!
@
1 / ( ) < > [ ] { } % ~ _ & (1 / ( ) < > [ ] { } % ~ _ &)
A B C 2 –
D E F 3 –
G H I 4 –
(a b c 2 –)
(d e f 3 –)
(g h i 4 –)
(j k l 5 –)
A B C 2 Ä
D E F 3 É
G H I 4
(a b c 2 ä à ç)
(d e f 3 é è)
(g h i 4 ì)
J K L 5 –
J K L 5
(j k l 5)
M N O 6 –
P Q R S 7 –
T U V 8 –
W X Y Z 9 –
(m n o 6 –)
(p q r s 7 –)
(t u v 8 –)
(w x y z 9 –)
M N O 6 Ö Ñ
P Q R S 7
T U V 8 Ü
(m n o 6 ö ñ ò)
(p q r s 7 ß)
(t u v 8 ü ù)
W X Y Z 9 Æ Ø Å (w x y z 9 æ ø å)
Shift mode
* Γ ∆ Θ Λ Ξ Π Σ Φ Ψ Ω
*
(Hold) Space # £ $ ¥ ¤ @ \ § ^ | ↵
Delete text / (Hold) Delete all characters
#
NOTE: Displayed characters in the T9® mode vary depending on the selected input
language. Use ! to toggle T9® On/Off. If the combination of letters typed has
produced a word which is not the one you require, press A repeatedly until the
correct word is displayed. Then continue to the next word. When “–” is reached,
press @ to spell the word you require.
Basic Operations
19
Shift mode change
In text entry mode, you can change mode by pressing and
holding C.
Multi tap
Tegic
Abc -> abc -> ABC -> 123
T9Abc -> T9abc -> T9ABC ->
123
Text Input mode change
In text entry mode, to switch T9® mode On/Off, press!.
Auto capital change
Auto capital affects Abc and T9Abc.
When Input mode is changed to Abc or T9Abc, the first
character is input as upper case and subsequent letters as
lower case.
When one of the following characters [. (Period) or ! or ? ] is
input before a space, the next character is input as upper
case.
T9® Text Input
Using this mode of text input dramatically reduces the
required number of key presses.
Press a key once for any letter you require on that key. The
desired letter may not be displayed. Continue pressing other
keys until the end of a word is reached, then check that the
word has been typed correctly before continuing on to the
next word. If the combination of letters typed has produced a
word which is not the one you require, press A repeatedly
until the correct word is displayed. Then continue to the next
word.
20
Basic Operations
Example of Text Input in T9® Mode
To type a new message, follow these steps:
1. At the beginning of a new message press and hold
@(Clear) to delete previous text, if necessary
2. Press C to change letter case, if necessary
3. Press % % ( ( “Call” is displayed
Note that the displayed words change as you type. Always
type to the end of the word before editing.
If the word you require is not in the internal dictionary, then it
should be entered using the Multi tap (ABC) mode.
Other text modes
Multi tap mode (Abc, abc or ABC):
Each time a key is pressed in quick succession, the next
character available on that key is displayed. Releasing the
key or pressing another key enters the character displayed.
The cursor moves to the next position.
In T9 (Abc) or Multi tap (Abc) mode, the first entered letter in
a sentence is in upper case.
Basic Operations
21
Menu Display
NOTE: Menu display contents are dependent on your SIM.
The menu system provides the means for accessing the functions which do not
have their own dedicated buttons on the keypad.
From idle mode
1. A(Menu)
The main menu display has 9 menu options
2. 4 required menu A(Select)
OR
press a number next to a menu icon to access a menu option directly.
To go back to the Menu display,
D or @ repeatedly until to the Menu display returns.
22
Basic Operations
Menu Structure
The 9 main menus are as follows:
My Phone
Sounds
Display
Games
Hit Mouse
Memory
Contacts
Browse
Create
Language
Alerts
Profiles
Auto answer
Any key answer
Defaults
Groups
Memory status
My Numbers
Hotkey dial
My Contacts
Messages
Create
Calendar
Key Guard
Inbox
Outbox
Archive
User Messages
Memory status
Settings
Cell Broadcast
Application
Clock
Calculator
Currency
Melody composer
(Phone Menu)*
Phone Menu
(or STK) *
Call Service
Call Diverts
Security
Records
Last dialled
Answered
Unanswered
Delete all
Network
*STK(SIM Tool Kit) is SIM dependent.
Menu Structure
23
My Phone Menu
My Phone
Sounds
Display
Language
Alerts
Profiles
.............................................................................................30
Auto answer
Any key answer
Defaults
.............................................................................................30
.............................................................................................30
24
My Phone Menu
Sounds
Ringtones
You can change the ringtones for specific events such as
incoming calls, messages, or alarms. To customise the
ringtone, select the event first, then modify the ringtone.
From My Phone
1. 4 Sounds A(Select)
2. 4 Ringtones A(Select)
3. 4 Any call, Group calls, Alarm or Messages
A(Select)
4. 4 required ringtone A(OK)
Volume
From My Phone
1. 4 Sounds A(Select)
2. 4 Volume A(Select)
3. 4 Adjust the volume level A(OK)
Key tone
From My Phone
1. 4 Sounds A(Select)
2. 4 Key tone A(On/Off)
Warning tone
The warning tone informs you of low battery.
From My Phone
1. 4 Sounds A(Select)
2. 4 Warning tone A(On/Off)
My Phone Menu
25
Display
Wallpaper
You can change the wallpaper on the idle display. Idle mode
can also change to the clock.
From My Phone
1. 4 Display A(Select)
2. 4 Wallpaper @(Select)
3. 4 required wallpaper A(Select)
Greeting
You can create a greeting message that is displayed each
time the phone is switched on.
From My Phone
1. 4 Display A(Select)
2. 4 Greeting @(Edit)
3. Enter the greeting A(OK)
4. A(On/Off)
Animation
You can change the animation on the display when the
phone is powered up.
From My Phone
1. 4 Display A(Select)
2. 4 Animation A(Select)
3. 4 required animation A(Select)
26
My Phone Menu
Contrast
You can adjust the contrast of the display.
From My Phone
1. 4 Display A(Select)
2. 4 Contrast A(Select)
3. 4 Adjust the contrast A(OK)
Backlight
You can select the backlight On/Off.
From My Phone
1. 4 Display A(Select)
2. 4 Backlight A(On/Off)
Language
T9 Input
When you create a text this function helps to dramatically
reduce the number of key presses.
From My Phone
1. 4 Language A(Select)
2. 4 T9 Input A(Select)
3. 4 required input type A(On/Off)
Display languages
It is possible to change the display language on your phone.
From My Phone
1. 4 Language A(Select)
2. 4 Display languages A(Select)
3. 4 required language A(Select)
My Phone Menu
27
Alerts
You can set your phone to ring and/or vibrate when you
receive a call or messages.
From My Phone
1. 4 Alerts A(Select)
2. 4 required alert A(Select)
The following options are available when a call is received:
- Ring only
- None
- Ring & Vibrate
- Vibrate only
- Ring once
Profiles
Activating a profile
You can switch between four profiles in your phone, each
with a distinct combination of alert method, ringtone, etc.
Profiles are set up for use in different environments.
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Activate A(Select)
The following options are available:
Suitable for everyday settings
Normal
Quiet
With a ringtone, appropriate for formal
occasions
Suitable when in noisy environments
Outdoor
Headset
Appropriate with vibrator when it is difficult
to hear the ringtone
28
My Phone Menu
Setting a profile
You can customise a profile by changing the ring volume, key
tone, warning tone, vibrator, and/or backlight.
Ring volume:
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Change settings A(Select)
4. 4 Ring volume A(Select)
5. 4 Adjust the volume level A(OK)
Key tone:
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Change settings A(Select)
4. 4 Key tone A(On/Off)
Warning tone:
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Change settings A(Select)
4. 4 Warning tone A(On/Off)
Vibrator:
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Change settings A(Select)
4. 4 Vibrator A(On/Off)
Backlight:
From My Phone
1. 4 Profiles A(Select)
2. 4 required profile A(Menu)
3. 4 Change settings A(Select)
4. 4 Backlight A(On/Off)
My Phone Menu
29
Auto answer
Auto answer can be set. To use this function, the personal
hands free earpiece needs to be connected to the phone.
From My Phone
4 Auto answer A(On/Off)
Any key answer
Calls can be answered by pressing any key (except D).
From My Phone
4 Any key answer A(On/Off)
Defaults
All personal settings are returned to their factory default
settings.
From My Phone
1. 4 Defaults A(Select)
2. “Restore factory settings?” @(Yes) or A(No)
30
My Phone Menu
Games Menu
Games
................................................................................... 31
................................................................................... 33
Hit Mouse
Memory
Selecting games
From Games menu
4 Hit Mouse or Memory A(Select).
NOTE: Once the power is switched off, High scores or Best scores
may be lost.
Hit Mouse
When you see the mouse, press any button from1 to 9 as
quickly as possible to hit it. Keep in mind that the cat is not
your target.
Example: If you press 5, you will hit the object hidden in the
5th hole. This game will end automatically and you will be
given a score. This score might be the highest one! Good
luck!
Key operation:
Press $ ~ ,.
Starting games:
Select New by pressing @(New).
Games Menu
31
To change settings:
1. A(Menu)
2. 4 Change settings A(Select)
3. 4 required setting A(On/Off)
To start the game on a level of your choice:
1. A(Menu)
2. 4 Level A(Select)
3. 4 required level @(Select)
To see the top score:
1. A(Menu)
2. 4 Top score A(Select)
To see the instructions:
1. A(Menu)
2. 4 Instructions A(Select)
32
Games Menu
Memory
Match cards to find pairs with as few tries as you can, and
make all cards visible. You can press keys 2, 4, 6, and 8 to
move the cursor as you wish, and key 5 to select cards.
When all cards are visible, you can get a score or maybe top
score. Good luck!
Key operation:
Press %, ', (, ), +.
Starting Games:
Select New by pressing @(New).
To change settings:
1. A(Menu)
2. 4 Change settings A(Select)
3. 4 required setting A(On/Off)
To start the game on a level of your choice:
1. A(Menu)
2. 4 Level A(Select)
3. 4 required level A(Select)
To see the top score:
1. A(Menu)
2. 4 Top score A(Select)
To see the instructions:
1. A(Menu)
2. 4 Instructions A(Select)
Games Menu
33
Contacts Menu
Contacts
SIM ...................................35
Phone...............................35
Browse
Create
Groups
Memory status
My Numbers
.............................................................................................39
.............................................................................................39
.............................................................................................40
Hotkey dial
My Contacts
34
Contacts Menu
Browse
Viewing the Contacts list in your SIM/Phone
You can search a number in the Contacts list.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required contact entry A(Menu)
3. 4 View A(Select)
If you press a letter key in step 2, you can jump to the first
entry starting with the letter.
Create
Creating a Contacts list in SIM
Phone numbers can be stored in your SIM.
You can store names, phone numbers, location and record
numbers in the SIM.
From Contacts
1. 4 Create A(Select)
2. 4 SIM A(Select)
3. Enter the name 5
4. Enter the phone number 5
5. A(Save)
6. “Saved in SIM” is displayed
NOTE: The length and amount of data are SIM dependent.
Contacts Menu
35
Creating a Contacts list in Phone
You can store name, phone numbers, groups and melodies
in your phone.
From Contacts
1. 4 Create A(Select)
2. 4 Phone A(Select)
3. Enter the name 5 > Phone
4. Enter the phone number 5 > Groups
5. @(Set) 4 required group A(Select)
6. @(Set) 4 required melody A(Select)
7. When entries are completed,A(Save)
8. “Saved in Phone” is displayed.
The entries are grouped together and are retained even if
you damage your SIM.
Storing a fixed dial number in FDN
The Fixed dial feature allows you to limit your outgoing calls
to a certain set of numbers saved in FDN, which is located in
your SIM. When this function is on, only the Fixed dial
numbers can be dialled, and any attempt to call any other
numbers will fail.
To activate this function, you need to set Fixed Dial on. See
page 62.
From Contacts
1. 4 Create A(Select)
2. 4 SIM A(Select)
3. Enter the name 5
4. Enter the phone number 5
5. @(Set) 4 FDN A(Select)
6. A(Save)
7. Enter PIN2 code > A(OK)
8. “Saved in SIM” is displayed.
To store a Fixed dial number, you need to enter your PIN2
code.
36
Contacts Menu
Options
Edit:
You can edit the selected Contacts entry.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required phone number or name A(Menu)
3. 4 Edit A(Select)
4. A(Save)
Delete:
You can delete the selected Contacts entry.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required phone number or name A(Menu)
3. 4 Delete A(Select)
4. “Delete this contact entry ?” A(Yes) or @(No)
Delete all:
You can delete all the Contacts entries.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required phone number or name A(Menu)
3. 4 Delete all A(Select)
4. “Delete all entries ?” A(Yes) or @(No)
Copy to Phone/SIM:
You can copy the selected Contacts entry to the phone or
your SIM.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required phone number or nameA(Menu)
3. 4 Copy to Phone/SIM A(Select)
4. “Copy entry to Phone/SIM ?” A(Yes) or @(No)
Contacts Menu
37
Copy all to Phone/SIM:
You can copy all the Contacts entries to the phone or SIM.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. 4 required phone number or name A(Menu)
3. 4 Copy all to Phone/SIM A(Select)
4. “Copy all entries to Phone/SIM ?” A(Yes) or
@(No)
Search:
You can search for a name in the Contacts list.
From Contacts
1. 4 Browse > SIM or Phone A(Select)
2. A(Menu)
3. 4 Search A(Select)
4. Enter the first letter of the required name A(Select)
Groups
You can categorise the items stored in your phone into 5
groups: Friends, Colleagues, Family, Others and VIP.
You can select a particular ringtone for each group to identify
the incoming call.
From Contacts
1. 4 Groups A(Select)
2. 4 required Group A(Menu)
The following options are available :
View
View the Contacts entries in the selected
group
Set ringtone
Set the required ringtone
Remove entries
Delete all the Contacts entries in the
selected group
If there is no entry stored in the selected group, “List empty”
is displayed.
38
Contacts Menu
The following options are available by pressing A(Menu)
after you select an entry from the selected group:
View
View the selected Contacts entry
Edit the selected Contacts entry
Delete the selected Contacts entry
Edit
Delete
Search
Search for a desired item in the selected
group by entering the name.
Memory status
Memory status shows how many locations are available in
the Contacts list.
Maximum memory capacity:
- Phone 250 locations
- SIM (SIM dependent)
From Contacts
4 Memory status A(Select)
My Numbers
My Numbers is a handy phonebook where names and phone
numbers can be stored and viewed.
From Contacts
1. 4 My Numbers A(Select)
2. 4 required entry A(Menu)
3. 4 Edit A(Select)
4. Enter your phone number 5
5. Enter your name A(Save)
The following options are available by pressing A(Menu)
when you select the required entry:
View
Edit
View the selected My Numbers entry
Edit the selected My Numbers entry
Delete the selected My Numbers entry
Delete
Contacts Menu
39
Hotkey dial
Setting Hotkey dial
You can quickly dial phone numbers stored at locations 001
- 009 in the Contacts list.
From Contacts
4 Hotkey dial A(On/Off)
NOTE: This function is SIM dependent.
Making a call by using Hotkey dial
From idle mode
1. Press and hold a numeric key ($ ~ ,)
2. Press C
My Contacts
You can select SIM or Phone so that the Contacts list directly
accessed from idle mode is set to the SIM or Phone Contacts
list.
From Contacts
1. 4 My Contacts A(Select)
2. 4 SIM or Phone A(Select)
40
Contacts Menu
Calendar
Calendar
New event
You can organise your Calendar to remind you of a personal
event, such as a holiday period or birthday.
You need to set the clock, day and time before entering
anything in the Calendar.
From Calendar
1. @ to select Week or Month format
2. To select a day, press numeric keys 2, 8, 4 and 6 to
move the cursor Ç, È, Å and Æ respectively, to set the
desired day. A(Agenda)
3. <New entry> A(Select)
4. @(Set) to select a type of event from Memo and
Meeting A(Select)
5. 4 to enter Description
6. 4 to enter Start date
7. 4 to enter Start time
8. 4 to enter End date
9. 4 to enter End time A(Save).
Ensure that Calendar settings will not contravene any
regulations by switching on automatically when in an aircraft,
medical facility, etc. – (see “Operating Instructions Part 2”.)
Calendar
41
View event
From Calendar
1. @ to select Week or Month format
2. When Month format is selected:
Select a day by using the numeric keys (1, 5, 2, 4, 6
and 8) A(Agenda)
When Week format is selected:
Schedule icon(s) will be shown corresponding to a
period of time selected by pressing 4.
(Period of time : 4=0:00-3:59, 8=4:00-7:59, 12=8:00-
11:59, 16=12:00-15:59, 20=16:00-19:59, 24=20:00-
23:59)
Select a day by using the numeric keys (2,4,6 and 8)
A(Agenda)
3. 4 required schedule @(View)
4. To return to the previous display, A(OK)
To edit @(Edit), edit the required information
A(Save).
<Example>
Agenda:2004/02/10 Start 0:00~End 3:00
Scheduled day
Scheduled time period
Agenda Month
Scheduled icon
=
=
=
0:00~ 3:59
4:00~ 7:59
8:00~11:59
= 12:00~15:59
= 16:00~19:59
= 20:00~23:59
Press
4
to change the schedule icon into
different periods of time.
42
Calendar
Key Guard
Key Guard
The Key Guard function is used to prevent any keys from
being accidentally pressed, e.g. when the phone is being
carried.
From Key Guard
1. A(Yes) or @(No)
When Key Guard is enabled, L appears on the display.
Emergency calls are still possible.
When a call is received, Key Guard will be disabled
temporarily, and you can answer the call
NOTE: When making emergency calls with the “Key Guard”
enabled, there will be no visual indication that the number is being
dialled.
When L appears on the display, A(Free) > “Press ok to
free keypad” A(OK) .
Key Guard
43
Messages Menu
Messages
............................................................................................. 45
Create
.............................................................................................48
.............................................................................................49
Inbox
Outbox
Archive
User Messages
Memory status
Settings
............................................................................................. 51
Cell Broadcast
44
Messages Menu
Create
Message centre
It is possible to receive, display, edit and/or send text
messages of up to 1520 characters in 10 messages
(depending on the language), to the network that has a
roaming agreement (depending on the recipient’s phone
options). Before sending a message, you need to enter the
Message centre number into Settings.
From Messages
1. 4 Settings > Message centre A(Select)
2. Enter the message centre number in the international
dial format
)
NOTE: Your network operator may have pre-programmed this
number. Do not change this number as it may cause the failure of
SMS Messaging.
Messages Menu
45
Creating a message
From Messages
1. 4 Create A(Select)
2. Create your text message – max. 1520 characters
3. 4 Send A(Select)
4. Enter the destination phone number A(OK)
OR
Recall a number from Contacts @(Names) >
4 required name A(Select) > A(OK)
When you create a text, these options are available by
pressing A(Menu):
Send
Send text as a Short Text message
Save text in the Outbox in your SIM
Save
Save and send
Save text in the Outbox in your SIM and
send it
Picture & sound
User Messages
Add a picture and/or sound to the text. See
Use a short message stored in the phone
For editing the User Message, see “User
You can change T9® mode On/Off pressing !.
46
Messages Menu
EMS (Enhanced Message Service)
You can add a picture and sound to an SMS.
Picture:
From Messages
1. 4 Create A(Select)
2. Create your text message A(Menu)
3. 4 Picture & sound A(Select)
4. 4 required picture A(Select)
Sound
From Messages
1. 4 Create A(Select)
2. Create your text message A(Menu)
3. 4 Picture & sound A(Select)
4. @(Sound)
5. 4 required sound A(Select)
Messages Menu
47
Inbox
Viewing a received message
When a Short Text Message is received, the message
indicator will flash on the display and a user preset audible
alert will sound. If you are on a call you will be alerted by the
vibrator.
flashes when an unread message is received in the Inbox.
When the Inbox is full,
deleted.
will remain until old messages are
From Messages
1. 4 Inbox A(Select)
2. 4 required message A(Menu)
3. 4 View A(Select)
NOTE: If the message indicator is displayed constantly (does not
flash), this means that the message area is full, and you need to
delete old messages in order to receive new messages.
When reading messages, the following options are available
by A(Menu)
:
Delete
Reply
Forward
Edit
Delete a message
Create an SMS reply
Forward a message to another phone
Edit a message and save and/or send it to
somebody else
Delete all
Delete all messages in Inbox
Extract Number
Extract numbers in messages and save in
Contacts
Move to Archive
Move a message to Archive Inbox
48
Messages Menu
Outbox
Viewing a sent message
A list of sent message is stored in your SIM. You can select
a message from the list and view it.
From Messages
1. 4 Outbox A(Select)
2. 4 required message A(Menu)
3. 4 View A(Select)
While you are reading a message, the following options are
available by pressing A(Menu):
Delete
Edit
Delete a message
Edit a message and save and/or send it to
somebody else
Send
Send an SMS message after entering a
recipient number
Delete all
Delete all messages in Outbox
Extract Number
Extract numbers in messages and save in
Contacts
Move to Archive
Move a message to Archive Outbox
Messages Menu
49
Archive
Viewing a stored message
To view the list of messages which are stored in Archive.
Inbox: When a message saved in the Inbox is moved into
Archive, the message will be saved in the Archive Inbox.
Outbox: When a message saved in the Outbox is moved
into Archive, the message will be saved in the Archive
Outbox.
From Messages
1. 4 Archive A(Select)
2. 4 Inbox or Outbox A(Select)
3. 4 required message A(Menu)
4. 4 View A(Select)
When reading a message, the following options are available
by A(Menu):
Send (Outbox)
Edit
Send a message to another phone
Edit a message and save and/or send it to
somebody else
Delete
Delete a message
Forward (Inbox)
Delete all
Forward a message to another phone
Delete all messages in Archive Inbox/
Outbox
50
Messages Menu
User Messages
You can edit the preset User Messages, then save them for
later use
.
From Messages
1. 4 User Messages A(Select)
2. 4 required message A(Select)
3. Edit the message A(Menu)
4. 4 Save and send or Save A(Select)
NOTE: If the text is wider than the screen display, the text will
scroll.
Memory status
Memory status shows how many locations are left to store
messages in the Inbox.
From Messages
4 Memory status A(Select)
The maximum memory capacity:
- SIM (SIM dependent – max. 100 locations)
- Phone 50 locations
- Archive 50 locations
Settings
Message centre
Before sending any messages, you need to enter your
Message centre number. This number is provided by your
service provider.
From Messages
1. 4 Settings A(Select)
2. 4 Message centre A(Select)
3. Enter your Message centre number
Messages Menu
51
Protocol
The Message centre is able to convert your message to the
format specified by the selected protocol.
From Messages
1. 4 Settings A(Select)
2. 4 Protocol A(Set)
3. 4 Select required setting from Standard text, Fax,
X.400, Paging, E-mail, ERMES, or Voicemail
A(Select)
Validity period
You can set the duration that your message is stored at the
Message centre.
From Messages
1. 4 Settings A(Select)
2. 4 Validity period A(Set)
3. 4 Select required setting from Maximum, 1 Hour, 12
Hours, 1 Day, or 1 Week A(Select)
Delivery report
You can request a delivery report regarding the status of a
sent message.
From Messages
1. 4 Settings A(Select)
2. 4 Delivery report A(On/Off)
52
Messages Menu
Cell Broadcast
Topic list
You can receive your favourite information regularly from
your service provider.
You need to specify the “topic(s)” of information and the
language in which you wish to receive this information.
To receive the broadcasts, “Cell Broadcast” must be on.
From Messages
1. 4 Cell Broadcast > Topic list > Current> A(Select)
2. 4 required topic A(Menu)
3. 4 Add or Delete A(Select)
User defined topic
From Messages
1. 4 Cell Broadcast > Topic list> User defined >
<New entry> A(Select)
2. Enter msg ID A(OK)
3. Enter the name A(OK)
4. 4 Current A(Select)
5. 4 < Add topic > A(Select)
6. 4 required Topic A(Select)
Reading a message
From Messages
1. 4 Cell Broadcast A(Select)
2. 4 Read Messages A(Select)
3. A(Next) to select the required topic
NOTE: This function will depend on your network service operator.
Messages Menu
53
Language
You can set the language of the message you receive.
From Messages
1. 4 Cell Broadcast A(Select)
2. 4 Display Languages A(Select)
3. 4 required language above which you wish to insert a
new language
4. 4 Insert A(Select)
5. 4 required language A(Select)
The added language is displayed above the language you
selected in step 3.
If you wish to add a new language to the end of the list,
select “Add to end” in step 4.
To resume a language, select “Delete” in step 4.
Auto display
In idle mode, the latest Info Message is displayed on your
phone automatically.
From Messages
1. 4 Cell Broadcast A(Select)
2. 4 Auto display A(On/Off)
54
Messages Menu
Call Service
Viewing time/charges
From Phone Menu
1. 4 Call Service > Time/Charges A(Select)
2. 4 Last call, All voice calls or Cost left A(Select)
Last call
Display the duration of last call
All voice calls
Cost left
Display the total duration for all voice calls
If Max cost is on, display the remaining
units.
For setting the Max cost, see page 58.
Call waiting
If Call waiting is switched on, a second call can be received.
Turn this function on before making a multiparty (conference)
call.
From Phone Menu
1. 4 Call Service > Call waiting A(Select)
2. 4 Set, Clear or Check status A(Select)
Withhold ID
Withhold ID allows you to prevent showing your name and/or
number to the calling party.
From Phone Menu
1. 4 Call Service A(Select)
2. 4 Withhold ID A(Select)
NOTE: When checking the status, the phone must be registered to
a network.
56
Phone Menu
Caller’s ID
Caller’s ID allows you to display the Caller’s name and/or
number on your display.
From Phone Menu
1. 4 Call Service A(Select)
2. 4 Caller’s ID A(Select)
NOTE: When checking the status, the phone must be registered to
a network.
Charge settings
NOTE: The duration of one unit may vary between peak and off-
peak times. Call charges can be calculated accordingly. However,
the actual tariffs charged by your service provider may not be
reflected in the calculation.
Currency:
Firstly, Personal rate must be entered. This is the cost that
the service provider charges for one unit of call time. See
From Phone Menu
1. 4 Call Service > Charge settings A(Select)
2. 4 Currency A(Select)
Current setting is displayed
3. @(Set) > Enter PIN2 codeA(OK)
4. Enter currency units (max. 3 characters) A(OK)
NOTE: This function is SIM dependent
Phone Menu
57
Personal rate:
From Phone Menu
1. 4 Call Service > Charge settings > Personal rate
A(Select)
2. @(Set)
3. Enter PIN2 code A(OK)
4. Enter your personal rate A(OK)
NOTE: When you set the unit price, you are asked to enter your
PIN2.
NOTE: This function is SIM dependent
Maximum cost:
You can set the maximum cost of calls allowed.
From Phone Menu
1. 4 Call Service > Charge settings A(Select)
2. 4 Max cost A(Set)
Current setting is displayed.
3. @(Edit) > Enter PIN2 code A(OK)
4. @(Set) >4 On A(Select)
5. 5 Enter Credit limit > A(OK)
NOTE: This function is SIM dependent
Auto display:
In idle mode, the cost of the latest Incoming call is displayed
on your phone automatically.
From Phone Menu
1. 4 Call Service > Charge settings A(Select)
2. 4 Auto display A(On/Off)
58
Phone Menu
Call Diverts
From Phone Menu
1. 4 Call Diverts A(Select)
2. 4 Select the circumstances to initiate the divert
A(Select)
3. 4 Set, Clear, or Check status A(Select)
4. Enter the phone number to divert to A
Enter the voice mail centre number if you wish incoming
voice calls to be diverted to the voice mail centre.
When a divert situation is enabled, the divert icon ( G ) is
displayed.
When updating or checking the status of Call Divert, the
phone must be registered to a network. (
)
All voice calls
Not reachable
Divert all incoming voice calls
When you are not in a coverage area, divert
incoming voice calls
No reply
Busy
If you do not answer the phone, divert
incoming voice calls
When a call is in progress, divert incoming
voice calls
Status check
Cancel all
Check the current Call Diverts status
Cancel all Call Diverts settings
Voice calls can be diverted to voicemail box or to a
number that you specify.
Phone Menu
59
Security
Call bar
Call barring restricts certain outgoing and/or incoming calls
using a password supplied by your service provider. When
updating/checking the status of Call bar, the phone must be
registered to a network.
From Phone Menu
1. 4 Security > Call bar A(Select)
2. 4 required setting from the table shown below
A(Set) or A(Select)
3. 4 required operation from Set, Clear or Check status
A(Select)
4. Enter required password A(Select)
All outgoing
Outgo int’l.
All outgoing calls are barred
International outgoing calls are barred
Out. int’l. x home
International outgoing calls except to your
home country are barred
All incoming
All incoming calls are barred
When roaming
All international incoming calls when
roaming outside the home PLMN are barred
Status check
Cancel all
Call bar status is displayed
Cancel all Call bar settings
Change Call bar password
Password
60
Phone Menu
Codes
Change phonecode:
The Phonecode is used for the SIM lock, which protects the
phone from being used with a SIM other than yours.
From Phone Menu
1. 4 Security > Codes A(Select)
2. 4 Change phonecode A(Select)
3. Enter a new phonecode A(OK)
4. Enter the new phonecode to verify A(OK)
PIN control:
The PIN protects your SIM against unauthorised use. If you
enable the PIN, every time the phone is switched on you will
be prompted to enter the PIN.
From Phone Menu
1. 4 Security > Codes A(Select)
2. 4 PIN Control
3. Enter PIN number A(OK)
4. 4 Set to either enable or disable the PIN @(Set).
5. A(OK)
Changing PIN/PIN2:
From Phone Menu
1. 4 Security > Codes A(Select)
2. 4 Change PIN or Change PIN2 A(Select)
3. Enter the current code A(OK)
4. Enter the new code A(OK)
5. Enter the new code to verify A(OK)
#
. You will then be
NOTE: To enter the PUK code for your PIN, enter **05
enter the PUK2 code for PIN2, enter **052
prompted to enter the PUK code. Follow the on-screen instructions. To
. You will then be prompted to
enter the PUK2 code. Follow the on-screen instructions. If the PUK/PUK2
code is entered incorrectly 10 times, the phone will cease to operate
permanently. All information stored in the SIM will be lost and the SIM will
need to be replaced. Contact the service provider for more details.
#
Phone Menu
61
Fixed dial:
The Fixed dial feature allows you to limit your outgoing calls
to a certain set of numbers saved in FDN, which is located in
your SIM. When this function is on, only the Fixed dial
numbers can be dialled, and any attempt to call any other
number will fail.
From Phone Menu
1. 4 Security A(Select)
2. 4 Fixed dial A(Select)
3. Enter PIN2 code A(OK)
4. @(Set)
5. A(OK)
When Fixed dial is on, any manually dialled phone
numbers must be the same as the numbers in the Fixed
Dial Store, otherwise the call cannot be made.
A phone number may be stored, edited or deleted. You
will be prompted for your PIN2 code.
SIM lock:
Once you enable the SIM lock, you will be prompted to enter
your phonecode when you switch on the phone with a
different SIM inserted.
From Phone Menu
1. 4 Security A(Select)
2. 4 SIM lock A(Select)
3. Enter phonecode A(OK)
4. A(Set) to set the SIM lock on/off
5. A(OK)
NOTE: Your phonecode must be 4 to 8 digits. You are advised to write
down your phonecode. If the phonecode is entered incorrectly 3 times,
the phone will cease to operate permanently.
62
Phone Menu
Network
Setting:
From Phone Menu
You can select a network that is available in your current
location.
1. 4 Network A(Select)
2. 4 Select one of the settings below A(On/Off) or
A(Select)
Auto network
New network
Set Auto network on or off.
When Auto Network is on, search an available
network automatically. When Auto network is
off, you must select a network manually.
Network list
Band
Create and edit a network list according to
your preferences.
Choose a network band: 900/1800, 900/
1900, 900, 1800, 1900 MHz.
NOTE: This function is SIM dependent
Phone Menu
63
Application Menu
Application
Clock
.............................................................................................67
Calculator
............................................................................................ 67
............................................................................................ 68
.............................................................................................69
Currency
Melody composer
(Phone Menu)*
64
Application Menu
Clock
Settings
Time zone:
From Application
1. 4 Clock > Settings > Time zone A(Select)
2. 4 required region A(Select)
3. “Daylight saving?” A(Yes) or @(No)
4. “Set this zone to local” @(OK)
5. “Success!” A(OK)
Time & date:
From Application
1. 4 Clock > Settings > Time & date A(Select)
2. @(Set) to enter the date and the time A(OK)
Date format:
You can select the desired display format for the time and
date.
From Application
1. 4 Clock > Settings > Date format A(Set)
2. 4 required format A(Select)
Time format:
From Application
1. 4 Clock > Settings > Time format A(Set)
2. 4 required format A(Select)
Application Menu
65
Display time:
You can show the time and date on the display in idle mode.
From Application
1. 4 Clock > Settings A(Select)
2. 4 Display time A(On/Off)
Alarm:
From Application
1. 4 Clock > Alarm A(Set)
2. A(Set) > Enter the time (24 hour clock) A(OK)
3. 4 Repeat daily, Once or Disabled A(Select)
4. “Alarm time has been updated!” A(OK)
The alarm set indicator appears on the idle display.
When the set time is reached, the alarm will sound.
If you are on a call, the phone will vibrate without sound.
To stop the alarm:
Press any key or A(Off)
OR
@(Pause) to pause the alarm and start again after 5
minutes
NOTE: Even if the phone is switched off, when the Alarm is set on,
the phone will switch on automatically and start the alarm.
Power off time
The phone can be set to turn itself off automatically at a
specified time using the Power off feature.
From Application
1. 4 Clock > Power off time A(Set)
2. Enter the time (24 hour clock) A(OK)
3. 4 Repeat daily, Once or Disabled A(Select)
4. “Power off time setting updated!” A(OK)
66
Application Menu
Calculator
You can use the 4 function calculator (addition, subtraction,
multiplication and division) to make simple arithmetic
calculations.
From Application
1. 4 Calculator A(Select)
2. Enter a number (max. 9 digits). It will be displayed on the
upper right of the display. If a decimal point is required,
press !, when a minus sign is needed press ".
3. 4 to select the arithmetic operation
4. Enter a number (max. 9 digits). It will be displayed next
to the operation symbol.
If 4 is used to select another arithmetical operation to
perform, an intermediate calculation will be performed
and the result will be displayed.
5. A (=) to calculate
Currency
Rate setting
The currency convertor enables you to convert from/to a
home currency using a conversion rate that you enter.
Before beginning conversions, choose a base currency and
enter the conversion rate. The base currency rate is set to 1.
From Application
1. 4 Currency A(Select)
2. 4 Rate setting A(Select)
3. Enter the conversion rate next to the pencil icon
A(OK)
4. A(Save)
You can change the base currency by pressing 4.
If a decimal point is required, press !
Application Menu
67
Rate computing
From Application
1. 4 Currency A(Select)
2. 4 Rate computing A(Select)
3. Enter the amount of your currency to convert into the
other currency A(Convert)
You can change the base currency by pressing 4.
If a decimal point is required, press !
Melody composer
Composing a melody
From Application
1. 4 Melody composer A(Select)
2. 4 required My Music A(Select)
3. 4 Melody edit A(Select)
4. 4 required track A(Select)
5. Compose your melody - See the notes chart below
A(Menu)
6. 4 Save A(Select)
Using the following table as a reference, enter notes (from
the choice of low, middle and high), rests, and duration of
each, to generate your composition. Main Track and Sub
Tracks are played together when you play the composed
music.
Key
$
%
&
(
)
'
Func
C
D
E
F
G
A
Key
*
+
,
#
"
!
Low,
Low #,
Middle,
Middle #,
High,
Dotted
note
Func
B
Rep.
Rest
Duration
High #
68
Application Menu
Play
To play the composed melody before saving:
A(Menu) > 4 Play A(Select)
Tempo
Before you save the composed melody, you can change the
tempo, and/or the instrument to play the melody.
To arrange the tempo of the composed melody:
1. A(Menu) > 4 Tempo A(Select)
2. 4 required tempo A(Select)
Select instrument
You can select the instrument to play the composed melody:
A(Menu) > 4 Select instrument A(Select)
Phone menu
This menu is available under the Application Menu if your
SIM card provides STK services.
Application Menu
69
Records Menu
Records
Last dialled
............................................................................................ 70
Answered
............................................................................................ 70
............................................................................................ 70
Unanswered
Delete all
............................................................................................ 70
Last dialled/Answered/Unanswered number
Recently dialled phone numbers will be stored in Last dialled.
(max. 50)
If an incoming call with Caller’s ID is answered, the number
will be stored in Answered (max. 50).
If an incoming call with Caller’s ID is not answered, the
number will be stored in Unanswered (max 20).
From Records
1. 4 Choose one menu from Last dialled, Answered or
Unanswered A(Select)
OR
In idle mode, C to view the last dialled numbers
directly
2. 4 required phone number (or name) you wish to redial
C
Delete all
From Records
1. 4 Delete all A(Select)
2. “Delete all calls?” A(No) or @(Yes)
70
Records Menu
Accessories
Li-Ion Battery (EB-BSA10)
Double your talk time by having a spare battery.
Rapid Charger (EB-CAD55UK)
Carry a lightweight portable charger wherever you go to
ensure you always have power to talk.
Rapid Charger (EB-CAD55EU)
Carry a lightweight portable charger wherever you go to
ensure you always have power to talk.
Personal handsfree (EB-EMG70)
Talk and move while keeping your hands free, by using a
personal handsfree. Put the ear piece in your ear and the
adaptor in the side of the handset, and talk.
How to Identify a Genuine Panasonic Accessory
Panasonic produces some of the most advanced mobile phones available. So, as
you’d expect from this class leader, the range of accessories are second to none.
Most genuine Panasonic accessories will have a label showing an “EB-XXX00”
model number.
NOTE: Accessories are subject to change without notice.
Accessories
71
Troubleshooting
Should any problem persist, contact your dealer.
Problem
Cause
Remedy
Phone will not switch
on.
Check that the battery is fully charged
and correctly connected to the phone.
Extremely short
battery life for a new
battery.
The network you are using
and the condition of the
battery can affect battery
life.
Short battery life for an The battery has worn out. Replace with a new fully charged
old battery. battery.
The charging indicator The battery is not attached Leave the phone charging the battery
does not light, the to the phone, or when the for a few minutes before the indicator
battery level indicator battery has been deeply lights and your attempt to switch the
does not appear and discharged, the phone will phone on.
the phone cannot be
switched on when
charging.
take a short time until the
indicator lights.
Battery fails to charge. The battery is not attached Ensure the battery is fitted to the
to the phone.
phone prior to commencing charging.
Battery was connected to
the phone after the Fast
Travel Charger was
switched on.
indicates abnormal
charging.
Replace with a new battery.
Unlock the phone.
Battery is defective or of
the wrong type.
Calls cannot be made. The phone is locked.
Outgoing calls are barred. Disable outgoing call barring or barred
dialling.
The phone is not
registered to a network.
Move to a coverage area and operate
your phone after it has registered with
a network.
Calls cannot be made
from Fixed Dial Store.
Check whether your SIM supports
Fixed dial.
Check if Fixed dial is switched on.
Check whether the phone number is
stored in Fixed Dial.
72
Troubleshooting
Problem
Cause
Remedy
Calls cannot be
received.
The phone is not switched Switch the phone on.
on.
Incoming calls are barred. Disable incoming call barring.
The phone is not
registered to a network.
Move to a coverage area and operate
your phone after it has registered with
a network.
Emergency calls
cannot be made.
You are not in a GSM
coverage area.
Check that the antenna symbol (
is displayed – move to a coverage
area and operate your phone when
the antenna symbol is displayed.
)
Phone numbers
cannot be recalled
from Contacts list.
The phone is locked.
Unlock the phone.
Phone number has been Switch off restriction.
restricted.
Troubleshooting
73
Important Error Messages
These are some of the most important error messages which may be displayed:
New codes not same
When you change your password, you must enter the new
password twice to confirm. The two codes you entered are not
the same. Enter the same code twice.
Password invalid
The password that you entered is not valid. Enter the correct
password.
New PIN not accepted
New PIN2 not accepted
Incorrect entry!
Your new PIN code was not accepted. Please try again.
Your new PIN2 code was not accepted. Please try again.
You entered your PIN or PIN2 code incorrectly. Enter the
correctly.
Entries do not match!
Invalid password
When you change your password, you must enter the new
password twice to confirm. The two codes you entered are not
the same. Enter the same code twice.
The reply message from network when you activate call barring
with the incorrect password.
Enter the correct password.
SIM service not support
The function you selected is not supported by your service
provider. Please contact your service provider.
Insufficient space!
Continue?
The SIM storage area is full. If you continue, data may be lost.
Please delete old records.
Not enough space!
Continue?
The message storage area is full. If you continue, data may be
lost. Please delete old records.
Authentication failure
Your SIM card is not registered with your service provider.
Please contact your service provider.
Blocked
Your SIM card is blocked. Please contact your service provider.
74
Important Error Messages
Glossary of Terms
DTMF
Dual Tone Multi-Frequency tones allow you to communicate with
computerised phone systems, voice mailboxes, etc.
FDN
Fixed Dial Number. Used to restrict outgoing calls to a certain set of
numbers.
GSM
Global System for Mobile communications. The name given to the
advanced digital technology that your phone uses.
Network
Operator
The organisation responsible for operating a GSM network.
Password
PIN
Used for the control of Call Bar.
Personal Identification Number used for SIM security. Supplied by your
service provider. If the PIN is entered incorrectly 3 times, the PIN will be
blocked.
PIN2
Personal Identification Number used for the control of Fixed Dial Store
and Call Charge metering. Supplied by your service provider. If the
PIN2 is entered incorrectly 3 times, the PIN2 will be blocked.
PLMN
Public Land Mobile Network. A network that provides land mobile
telecommunications services.
PUK/PUK2
PIN/PIN2 Unblocking Key. Used to unblock the PIN/PIN2 code.
Supplied by your service provider. If the PUK/PUK2 is entered
incorrectly 10 times, the PUK/PUK2 will be blocked.
Registration
Roaming
The act of logging on to a GSM/GPRS network. This is usually
performed automatically by your phone.
The ability to use your phone on networks other than your home
network.
Service
Provider
The organisation responsible for providing access to the GSM/GPRS
network.
SIM
Subscriber Identity Module. A small smart-card which stores unique
subscriber and user-entered information such as Contacts entries and
short messages. Supplied by your service provider.
SMS
Short Message Service. A basic mail system used for cellular phones.
This service allows sending/receiving of short text messages.
Glossary of Terms
75
Index
Auto display ...................... 58
Display time ...................... 66
Power off time ................... 66
Time & date ...................... 65
Time format ...................... 65
Creating in SIM ................. 35
Viewing ............................ 35
Rate computing ................. 68
A
Li-Ion Battery .................... 71
Personal handsfree ........... 71
Rapid Charger .................. 71
Auto answer ..................... 30
B
Charging ............................ 3
Fitting and removing ............ 1
C
Call
During a call ....................... 8
Incoming call while on a call 17
Making a second call ......... 16
D
E
76
Index
N
F
G
H
I
O
P
R
K
S
Fitting and removing ............ 3
L
M
Creating ........................... 46
T
T9® Input ............................... 27
T9® Text Input ....................... 20
U
Settings ........................... 51
V
Index
77
|