Nokia 6810 User Manual

User Guide for Nokia 6810

9311563

Issue 1

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and

improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special,

incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of

any kind, either express or implied, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or

contents of this document. Nokia reserves the right to revise this document or withdraw it at any time

without prior notice.

The availability of particular products may vary by region. Please check with the Nokia dealer nearest to

you.

Tips and hints

Tips and hints for using your new Nokia 6810 phone and for transferring data

from your previous phone to your new phone.

■ Transferring data from the previous phone

• If your old phone has no PC Suite support, the only way to transfer data is

via the SIM card.

1. Transfer all the contact information (names and phone numbers) in the old

phone to the SIM card. For more information, refer to the user guide of the

old phone.

2. Remove the SIM card and install it in your Nokia 6810 phone.

3. Press Menu and select Contacts, Copy, From SIM card to phone and All to

copy the contacts to the new phone.

• If your old phone has PC Suite support, you may be able to transfer data

using the Nokia Content Copier feature of PC Suite.

You can copy data directly from the old phone to the new phone. If you no

longer have the old phone, but you have backed it up to a compatible PC at

some stage, you may still be able to transfer the backup data to your new

phone. Note that only the data that was saved in the old phone when you last

backed it up with the PC can be transferred. For more information, refer to the

PC Suite documentation.

1. Install the PC Suite version delivered with your 6810 phone.

Note: You have to uninstall the old phone’s PC Suite version before you can

install the new version.

2. Start Nokia Content Copier.

3. If you still have the old phone, connect it to the PC and copy the data from

the phone to the PC, if you have not done it recently.

4. Connect your new phone to the PC and copy the old phone’s data from the

PC to the phone.

Note: Even if you no longer have the old phone, the old backup data is still

on your PC and you may be able to transfer it to your new phone.

With Nokia Content Copier, you can transfer the following data from the

following Nokia phones:

• All stored data from

• Nokia 3100 phone

• Nokia 3200 phone

• Nokia 5100 phone

• Nokia 6100 phone

• Nokia 6220 phone

• Nokia 6230 phone

• Nokia 6310i phone

• Nokia 6510 phone

• Nokia 6610 phone

• Nokia 6650 phone

• Nokia 6800 phone

• Nokia 6820 phone

• Nokia 7200 phone

• Nokia 7210 phone

• Nokia 7250 phone

• Nokia 7250i phone

• Nokia 7600 phone

• Nokia 8310 phone

• Nokia 8910 phone

• Nokia 8910i phone

•

Contacts and items in the Calendar from the Nokia 6210, 6250 and

7110 phones

• Only Contacts from the Nokia 5210, 8210 and 8850 phones

Note that you cannot back up the e-mail settings of the phone and thus

cannot transfer them from your old phone.

■ Returning to standby mode

• Press

to return to standby mode from anywhere in the menu.

■ Using the phone in standby mode

• Move the joystick to the left to start writing a message.

• Move the joystick to the right to view the current Calendar month.

• Move the joystick up or down to access the list of contacts.

• Press

to access the list of upto 20 last numbers you have called. Select the

number you require and press

again to make a call.

• Press

to open a connection to a browser service (network service).

• Press and hold

to call your voice mailbox (network service).

Note that the speed dialling function must be set on. Press Menu, and select

Settings, More settings,Call settings and Speed dialling.

• Key in the phone number and press Save to save a new contact. Then key in the

name, press OK and Done.

• Change the profile: press

, scroll to the profile that you want to activate

and press Select.

■ Using the security keyguard

• The security keyguard locks the keypad of the phone with a security code, see

Security code (5 to 10 digits) on page 20. The keypad lock remains active, if you

open the flip. Press Menu and select Settings, More settings, Phone settings

and Security keyguard.

Enter the security code. To set the security keyguard, select On.

To activate the security keyguard, press Menu and

within 1.5 seconds,

when the flip is closed. To deactivate the keyguard when the flip is open, press

Unlock and OK, then key in the security code. If the flip is closed, press Unlock

and

within 1.5 seconds, then key in the security code.

■ Turning on the phone lights

• When the keypad is locked, press the power key (

and display lights.

) to turn on the keypad

• When the flip is open, press the keyboard light key ( ) to turn on and off the

keyboard lights.

■ Using the e-mail application

• To use your phone’s e-mail application, you have to configure the e-mail and

connection settings. For more information, see Settings for the e-mail

application on page 92, or the Guide for e-mail application settings leaflet in

the phone’s sales package.

To set up the e-mail service with your operator, refer to www.nokia.com/

phonesettings.

■ Setting up a Bluetooth connection

1. Press Menu, and select Settings, Connectivity and Bluetooth.

2. To activate the Bluetooth connection, select Bluetooth and On.

3. Select Search for audio enhancements to search for compatible devices and

select the device that you want to connect to the phone.

4. Enter the passcode of the selected device.

■ Writing text

• To set the predictive text input on or off, press

twice, or press and hold

Options.

• To insert a special character when using traditional text input, press

when using predictive text input, press and hold

Move the cursor with the joystick to a character and press Use.

• To change the font size of the SMS messages, press Menu and select Messages,

Message settings, Other settings, and Font size.

■ Viewing contacts

• To view a contact name with the default number, press and hold

at the

name while scrolling through Contacts.

■ Viewing the calendar and calendar notes

• To quickly view the current Calendar month, move the joystick to the right in

standby mode.

• When viewing the calendar notes, move the joystick to the right to scroll

through the notes.

■ Customising personal shortcuts

• Press Go to and select Select options to select the functions you want as

shortcuts.

• Press Go to and select Organise to rearrange the functions within the shortcut

list.

■ Using the radio

• Return to standby mode by pressing

briefly; turn off the radio by pressing

and holding

• The lead of the headset functions as the radio antenna, so let it hang freely.

• Save the channel in locations 1 to 9 by pressing and holding the corresponding

number key, then keying in the name of the channel and pressing OK.

■ Using the calculator

• When using the calculator with the flip closed, press

to subtract, three times to multiply or four times to divide.

once to add, twice

Contents

FOR YOUR SAFETY ..............................................................................................16

General information............................................................................................20

Access codes ...............................................................................................................................................20

Security code (5 to 10 digits).............................................................................................................20

PIN and PIN2 codes (4 to 8 digits), Module PIN and Signing PIN...........................................20

PUK and PUK2 codes (8 digits)...........................................................................................................21

Barring password (4 digits).................................................................................................................21

Wallet code (4 to 10 digits)................................................................................................................21

Overview of the phone functions..........................................................................................................22

Shared memory.......................................................................................................................................23

1. Getting started ................................................................................................24

Installing the SIM card and the battery..............................................................................................24

Charging the battery ................................................................................................................................27

Switching the phone on and off ...........................................................................................................27

Opening the flip......................................................................................................................................29

Switching the keyboard lights on or off..........................................................................................32

2. Your phone.......................................................................................................33

Keys (flip closed)........................................................................................................................................33

Connectors...................................................................................................................................................35

Headset.........................................................................................................................................................35

Keys (flip open)...........................................................................................................................................36

Standby mode.............................................................................................................................................38

Screen saver.............................................................................................................................................40

Wallpaper.................................................................................................................................................40

Essential indicators in standby mode...............................................................................................40

Keypad lock (Keyguard) ...........................................................................................................................43

Over-the-air settings service .................................................................................................................44

3. Call functions ..................................................................................................46

Making a call ..............................................................................................................................................46

Speed dialling a phone number.........................................................................................................47

Answering or rejecting an incoming call............................................................................................48

Call waiting..............................................................................................................................................48

Options during a call................................................................................................................................49

4. Writing text.....................................................................................................51

Writing text using the messaging keyboard......................................................................................51

Typing accented characters ................................................................................................................52

Writing text when the flip is closed ....................................................................................................52

Setting predictive text input on or off.............................................................................................53

Using predictive text input..................................................................................................................53

Using traditional text input ................................................................................................................54

Tips for writing text...............................................................................................................................55

5. Using the menu ...............................................................................................57

Accessing a menu function ....................................................................................................................57

List of menu functions.............................................................................................................................59

6. Menu functions...............................................................................................63

Messages (Menu 1)...................................................................................................................................63

Text messages (SMS).............................................................................................................................63

Archive folder and my folders ............................................................................................................67

Templates .................................................................................................................................................68

Distribution lists.....................................................................................................................................69

Text message counter...........................................................................................................................70

Multimedia messages ...........................................................................................................................70

Deleting messages .................................................................................................................................76

E-mail application .................................................................................................................................76

Chat............................................................................................................................................................80

Voice messages.......................................................................................................................................89

Info messages..........................................................................................................................................89

Message settings....................................................................................................................................90

Settings for the e-mail application ..................................................................................................92

Font size setting.....................................................................................................................................97

Service commands.................................................................................................................................97

Call register (Menu 2) ..............................................................................................................................97

Recent calls lists.....................................................................................................................................98

Timers and counters..............................................................................................................................98

Contacts (Menu 3) ....................................................................................................................................99

Selecting settings for contacts ....................................................................................................... 100

Saving names and phone numbers (Add contact)..................................................................... 100

Adding an image to a name or number in contacts................................................................. 102

Searching for a contact..................................................................................................................... 103

Deleting contacts................................................................................................................................ 104

Editing or deleting details in contacts.......................................................................................... 104

My presence.......................................................................................................................................... 105

Subscribed contacts ........................................................................................................................... 107

Copying contacts................................................................................................................................. 109

Sending and receiving a business card......................................................................................... 110

Speed dials............................................................................................................................................ 110

Voice dialling........................................................................................................................................ 111

Info numbers and service numbers................................................................................................ 113

My numbers.......................................................................................................................................... 113

Caller groups ........................................................................................................................................ 113

Settings (Menu 4)................................................................................................................................... 114

Profiles ................................................................................................................................................... 114

Chat and my presence settings....................................................................................................... 115

Tone settings ........................................................................................................................................ 116

Display settings.................................................................................................................................... 117

Time and date settings...................................................................................................................... 118

Personal shortcuts .............................................................................................................................. 119

Connectivity.......................................................................................................................................... 120

More settings ....................................................................................................................................... 126

Security settings.................................................................................................................................. 131

Restore factory settings.................................................................................................................... 132

Gallery (Menu 5)..................................................................................................................................... 132

Radio (Menu 6)........................................................................................................................................ 135

Tuning a radio channel...................................................................................................................... 136

Using the radio .................................................................................................................................... 136

Organiser (Menu 7)................................................................................................................................ 138

Alarm clock........................................................................................................................................... 138

Calendar................................................................................................................................................. 139

To-do list ............................................................................................................................................... 142

Notes....................................................................................................................................................... 142

Wallet..................................................................................................................................................... 143

Synchronisation................................................................................................................................... 148

Applications (Menu 8)........................................................................................................................... 151

Games..................................................................................................................................................... 151

Collection .............................................................................................................................................. 152

Extras...................................................................................................................................................... 154

Services (Menu 9)................................................................................................................................... 158

Basic steps for accessing and using services.............................................................................. 159

Setting up the phone for a service................................................................................................. 159

Connecting to a service..................................................................................................................... 160

Browsing the pages of a service..................................................................................................... 161

Disconnecting from a service .......................................................................................................... 163

Appearance settings of the multi-mode browser...................................................................... 163

Cookies................................................................................................................................................... 164

Bookmarks............................................................................................................................................. 165

Downloading ........................................................................................................................................ 165

Service inbox........................................................................................................................................ 166

Cache memory..................................................................................................................................... 167

Browser security.................................................................................................................................. 167

SIM services (Menu 10)........................................................................................................................ 170

7. PC Connectivity ............................................................................................ 172

PC Suite..................................................................................................................................................... 172

EGPRS, HSCSD and CSD.................................................................................................................... 174

Using data communications applications ....................................................................................... 174

8. Battery information...................................................................................... 175

Charging and Discharging.................................................................................................................... 175

CARE AND MAINTENANCE.............................................................................. 177

IMPORTANT SAFETY INFORMATION............................................................... 178

FOR YOUR SAFETY

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further

detailed information is given in this manual.

Do not switch the phone on when wireless phone use is prohibited or when it

may cause interference or danger.

ROAD SAFETY COMES FIRST

Don't use a hand-held phone while driving.

INTERFERENCE

All wireless phones may get interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any regulations or rules. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Don't use the phone at a refuelling point. Don't use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Don't use the phone where blasting is in progress. Observe restrictions, and

follow any regulations or rules.

USE SENSIBLY

Use only in the normal position. Don't touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair phone equipment.

ACCESSORIES AND BATTERIES

Use only approved accessories and batteries. Do not connect incompatible

products.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user's guide for detailed safety

instructions. Do not connect incompatible products.

BACKUP COPIES

Remember to make backup copies of all important data

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

CALLING

Ensure the phone is switched on and in service. Enter the phone number,

including the area code, then press

call, press

To end a call, press

. To answer a

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press

as many times as

needed (e.g. to exit a call, to exit a menu, etc.) to clear the display. Enter the

emergency number, then press

told to do so.

. Give your location. Do not end the call until

■ Network Services

The wireless phone described in this guide is approved for use on the EGSM 900, GSM1800

and GSM 1900 networks.

Triband is a network dependent feature. Check with your local service provider if you can

subscribe to and use this feature.

This phone supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some

features of this phone, such as MMS, browsing, e-mail, chat, presence-enhanced contacts,

remote OMA Data Syncronization, and content downloading via browser or over MMS,

require network support for these technologies.

A number of features included in this guide are called Network Services. These are special

services that you arrange through your wireless service provider. Before you can take

advantage of any of these Network Services, you must subscribe to them through your

service provider and obtain instructions for their use from your service provider.

Note: Some networks may not support all language-dependent characters and/or

services.

■ About enhancements

Check the model number of any charger before use with this device. This device is intended

for use when supplied with power from ACP-7, ACP-8, ACP-9, ACP-12, LCH-8, LCH-9, LCH-

12 and AC-1.

Warning: Use only batteries, chargers and accessories approved by the phone

manufacturer for use with this particular phone model. The use of any other types

may invalidate any approval or warranty applying to the phone, and may be

dangerous.

For availability of approved accessories, please check with your dealer.

A few practical rules for enhancements operation

•

Keep all accessories out of the reach of small children.

When you disconnect the power cord of any accessory, grasp and pull the plug, not the

cord.

•

Check regularly that any vehicle-installed accessories are mounted and are operating

properly.

Installation of any complex car accessories must be made by qualified personnel only.

General information

■ Access codes

Security code (5 to 10 digits)

The security code helps to protect your phone against unauthorised use. The

preset code is 12345. When you have changed the code, keep the new code secret

and in a safe place separate from your phone. To change the code, and to set the

phone to request it, see Security settings on page 131.

If you key in an incorrect security code five times in succession, the phone may

display Code error. Wait for five minutes and key in the code again.

PIN and PIN2 codes (4 to 8 digits), Module PIN and Signing PIN

• The PIN (Personal Identification Number) code protects your SIM card against

unauthorised use. The PIN code is usually supplied with the SIM card. Set the

phone to request the PIN code each time the phone is switched on, see

Security settings on page 131.

• The PIN2 code may be supplied with the SIM card and is required to access

some functions.

• The module PIN is required to access the information in the security module.

See Security module on page 167. The module PIN is supplied with the SIM

card if the SIM card has a security module in it.

• The signing PIN is required for the digital signature. See Digital signature on

page 169. The signing PIN is supplied with the SIM card if the SIM card has a

security module in it.

If you key in an incorrect PIN code three times in succession, the phone may

display PIN blocked or PIN code blocked and ask you to key in the PUK code.

PUK and PUK2 codes (8 digits)

The PUK (Personal Unblocking Key) code is required to change a blocked PIN code.

The PUK2 code is required to change a blocked PIN2 code.

If the codes are not supplied with the SIM card, contact your network operator or

service provider.

Barring password (4 digits)

The barring password is required when using the Call barring service, see Security

settings on page 131. You can obtain the password from your service provider.

Wallet code (4 to 10 digits)

The wallet code is required to access the wallet services. If you key in an incorrect

wallet code several times, the wallet application is blocked for five minutes. For

further information, see Wallet on page 143.

■ Overview of the phone functions

Your Nokia 6810 phone is approved for use on EGSM 900, GSM 1800 and GSM

1900 networks. It provides many functions that are practical for daily use, such as

calendar, radio, loudspeaker, clock and alarm clock. Your phone also supports the

following functions (many of which are network services):

• EDGE (Enhanced Data rates for GSM Evolution), see EGPRS on page 123. EDGE

packet transmission networks enable faster connection than GPRS.

• The xHTML browser, which allows you to retrieve and view colourful and rich

graphical content from service providers’ web servers. See Services (Menu 9)

on page 158.

• Presence-enhanced contacts, which allow you to conveniently share your

availability information with your colleagues, family and friends with

compatible devices and services. See My presence on page 105.

• Chat, which is a way of sending short text messages that are delivered to

online users. See Chat on page 80.

• The messaging keyboard for writing text comfortably, see Writing and sending

messages on page 63.

• The e-mail function, which allows you to write, send and retrieve e-mails from

your e-mail account. See E-mail application on page 76.

• The multimedia messaging service (MMS), which allows you to send and

receive multimedia messages that contain text, picture, sound or video clips to

and from compatible devices. You can save the pictures and ringing tones for

personalising your phone, see Multimedia messages on page 70.

• Polyphonic sound (MIDI), which consists of several sound components that are

played at the same time. The phone has sound components from over 40

instruments and it can play up to 16 instruments at the same time. The phone

supports Scalable Polyphonic MIDI (SP-MIDI) format.

• Java 2 Micro Edition, J2ME^TMincludes some Java^TMapplications and games

that have been specially designed for mobile phones. You can download new

applications and games to your phone, see Applications (Menu 8) on page 151.

• An integrated stereo radio. You can listen to the radio using a headset or via

the loudspeaker, see Radio (Menu 6) on page 135.

Shared memory

The following features in this phone may share memory: contacts, text, chat and

multimedia messages, the e-mail application, voice tags and SMS distribution

lists, images, ringing tones, video and sound clips in the gallery, calendar, to-do

notes, Java games, applications, and the note application. Using any oif these

features may reduce the memory available for applications that require shared

memory. This is especially true with heavy use of any of the features (although

some of them may have a certain amount of memory specially allotted to them in

addition to the amount of memory shared with other features). For example,

saving many images, Java applications, etc. may take all of the shared memory

and your phone may display a message that the memory is full. In this case, delete

some of the information or entries stored in the shared memory features before

continuing.

1. Getting started

■ Installing the SIM card and the battery

•

Keep all miniature SIM cards out of the reach of small children.

• The SIM card and its contacts can easily be damaged by scratches or bending,

so be careful when handling, inserting or removing the card.

• Before installing the SIM card, always make sure that the phone is switched off

and disconnected from any enhancement and then remove the battery.

1. With the back of the phone facing you, push

the back cover release button (1) and, at the

same time, slide the back cover off the

phone. If the battery is in place, remove it by

lifting it up.

2. To release the SIM card holder, slide the card

holder backwards (2) and lift it up (3). Insert the SIM card into the SIM card

holder (4). Make sure that the SIM card is properly inserted and that the golden

contact area on the card is facing downwards.

3. Close the SIM card holder (5) and slide it back into place (6).

4. Replace the battery (7).

5. Direct the back cover towards the locking catches on the phone (8) and slide

the back cover until it locks into place (9).

■ Charging the battery

1. Connect the lead from the charger to

the socket on the bottom of your

phone.

2. Connect the charger to an AC wall

socket.

The text Charging is displayed briefly

if the phone is switched on. If the

battery is completely flat, it may take a few minutes before the charging

indicator appears on the display or before any calls can be made.

You can use the phone while the charger is connected.

The charging time depends on the charger and the battery used. For example,

charging a BLC-2 battery with the ACP-12 charger takes about 1 hour and 30

minutes while the phone is in standby mode.

■ Switching the phone on and off

Warning: Do not switch the phone on when wireless phone use is prohibited or

when it may cause interference or danger.

Press and hold the power key

• If the phone requests a PIN code or a security code, key

in the code, and press OK.

See also Security settings on page 131 and General

information on page 20.

• If the phone displays Insert SIM card even though the

SIM card is properly inserted, or SIM card not supported,

contact your network operator or service provider. Your

phone does not support 5-Volt SIM cards and the card may need to be

changed.

TIPS ON EFFICIENT OPERATION: Your phone has a built-in

antenna. As with any other radio transmitting device, do

not touch the antenna unnecessarily when the phone is

switched on. Contact with the antenna affects call quality

and may cause the phone to operate at a higher power

level than otherwise needed. Not touching the antenna

area during a phone call optimises the antenna

performance and the talktime of your phone.

Opening the flip

1. Hold the phone with

both hands and open

the flip as shown in

picture (1).

2. Turn the flip until you hear it click into place (2).

Make sure that the golden contacts of the flip and

the phone touch each other.

3. Turn the phone to a horizontal position and hold it as shown in picture (3). The

loudspeaker function automatically activates when the flip is open.

Switching the keyboard lights on or off

• The keyboard lights are not lit automatically, when you open the flip. To turn

on the lights, press the light key

on the top left corner of the keyboard. The

keyboard lights are switched off after a certain time, but they are turned on

again as soon as you press any key.

• To switch the keyboard lights off, press the keyboard light key or close the flip.

2. Your phone

■ Keys (flip closed)

1. Power key

Switches the phone on and

off.

When the keypad is locked,

pressing the power key turns

the phone’s display lights on

for approximately 15 seconds.

2. Volume key

Adjusts the volume of the

earpiece, the headset and the

loudspeaker.

3. Selection keys

and

The function of the keys

depends on the guiding text

shown on the display above

the keys, see Standby mode

on page 38.

4. 5-way joystick

Enables scrolling through names, phone numbers, menus or settings. The 5-

way joystick is also used to move the cursor up and down, right and left when

writing text, using the calendar, and in some game applications. Pressing the

joystick also functions as the middle selection key, and pressing it briefly

selects the function shown on the display above the joystick.

In standby mode, the joystick functions as a shortcut. Press the joystick

• right to access the Calendar.

• left to start writing an SMS message.

• up or down to access the list of contacts.

dials a phone number, and answers a call. In standby mode it shows the list

of the most recently called numbers.

ends an active call. Exits from any function.

enter numbers and characters.

and

are used for various purposes in different functions.

8. Ear piece

■ Connectors

1. Charger connector

2. Pop-Port^TMconnector for

headsets, data cable and other

enhancements. Connect an

enhancement to the Pop-Port

connector as shown in the

picture.

3.Infra

red (IR) port

4.Loudspeaker

5.Microphone

■ Headset

Connect the compatible headset to the Pop-Port connector of your phone.

Warning: This headset may affect your ability to hear sounds around you.

Do not use this headset in situations that may endanger your safety.

You can carry the headset as shown in the

picture.

■ Keys (flip open)

When you open the flip, the display graphics are rotated 90 degrees and the left,

middle and right selection keys change positions, but the guiding texts above the

selection keys do not change. To use the keys to write and edit text, see Writing

text using the messaging keyboard on page 51.

1. Keyboard light key

switches the keyboard light on or off to provide

additional lighting while using the keyboard. See also Switching the keyboard

lights on or off on page 32.

2. Profile key opens a list of profiles when pressed briefly. Pressing and

holding down the key switches the phone off.

ends an active call. Exits from any function.

4. Backspace

deletes characters.

5. Enter key

forces a line feed when editing text.

6. Shift keys

and

enter upper-case letters and symbols. You can

either press the shift key first and then the desired key or press both keys at the

same time.

7. Space bar keys

and

enter a space.

8. 5-way joystick

. For usage, see Keys (flip

closed) on page 33. To select a function as

shown in the picture, press the joystick when

the flip is open.

dials a phone number, and answers a call.

In standby mode it shows the list of most

recently called numbers.

10.Right selection key . The function of the

key depends on the guiding text shown on the display above the key.

11.Power key/Left selection key switches the power on and off. When the

phone’s messaging keyboard is open and the phone is on, the function of the

left selection key depends on the guiding text shown on the display above the

key.

12.Character key

opens a set of characters and symbols during text writing.

■ Standby mode

When the phone is ready for use (the flip can be either closed or open), and you

have not keyed in any characters, the phone is in standby mode.

1. Shows the name of the network or the

operator logo to indicate in which cellular

network the phone is currently being used.

2.Shows the signal strength of the cellular

network at your current location. The higher

the bar, the stronger the signal.

3.Shows the battery charge level. The higher

the bar, the more power in the battery

4.The left selection key in standby mode is Go

to.

Press Go to to view the list of available functions that you can add to your

personal shortcut list. Press Options and select

•

Select options to view the list of available functions that you can add.

Scroll to the desired function and press Mark to add it to the shortcut list.

To remove a function from the list, press Unmark.

•

Organise to rearrange the functions within the list. Select the desired

function and press Move, then select where you want to move the function.

If for some reason you have deleted the content of the Go to menu, press

Add to add a function.

5. The middle selection key in standby mode is Menu.

6. The right selection key in standby mode is Names, an operator-specific key or a

shortcut to a function that you have selected. If you press the right selection

key when the text is

• Names, you can access the Contacts menu.

• the operator-specific key, you can access an operator-specific web site.

• a specific function that you have selected and activated in Right selection

key, you can access it directly. See Personal shortcuts on page 119.

See also Essential indicators in standby mode on page 40.

Screen saver

The phone automatically activates a screen saver after a certain length of time

when none of the phone functions have been used, see Display settings on page

117.

When the screen saver is on, the phone still displays the icons indicating missed

calls

, keypad lock

, silent mode , received messages

and received

multimedia messages

Wallpaper

You can set your phone to display a background picture as wallpaper when the

phone is in standby mode, see Display settings on page 117.

Essential indicators in standby mode

You have received one or several text or picture messages. See Reading

and replying to an SMS message or an SMS e-mail on page 66.

You have received one or several multimedia messages. See Reading and

replying to a multimedia message on page 73.

Your phone is connected to the chat service and the availability status is

online or offline, respectively. See Connecting to and disconnecting from

the chat service on page 83.

You have received one or several chat messages and you are connected to

the chat service. See Connecting to and disconnecting from the chat

service on page 83.

The phone’s keypad is locked. See Keypad lock (Keyguard) on page 43 and

Automatic keyguard and Security keyguard in Phone settings on page

128.

The phone does not ring for an incoming call or a text message because

Incoming call alert is set to Off and Message alert tone is set to Off. See

Tone settings on page 116.

The alarm clock is set to On. See Alarm clock on page 138.

The countdown timer is running. See Countdown timer on page 157.

The stopwatch is running in the background. See Stopwatch on page 157.

When the EGPRS connection mode Always online is selected and the

EGPRS service is available, the indicator is shown on the top left of the

display. See EGPRS connection on page 124.

When an EGPRS connection is established, this indicator is shown on the

top left of the display. See EGPRS connection on page 124 and Browsing

the pages of a service on page 161.

The EGPRS connection is suspended (on hold), for example, if there is an

incoming or outgoing call during an EGPRS dial-up connection.

The infrared connection indicator. See Infrared on page 122.

The Bluetooth connection indicator. See Bluetooth wireless technology

on page 120.

All your calls are diverted to another number. If you have two phone lines,

the divert indicator for the first line is

See Call settings on page 126.

and for the second line is

or If you have two phone lines, the indicator displays the selected phone

line. See Call settings on page 126.

The loudspeaker has been activated. See Options during a call on page 49.

Calls are limited to a closed user group. See Security settings on page 131.

The timed profile is selected. See Profiles on page 114.

A headset, handsfree, loopset or music stand enhancement is connected

to the phone.

Time and date

See Time and date settings on page 118.

■ Keypad lock (Keyguard)

You can lock the keypad to prevent the keys being accidentally pressed, for

example, when your phone is in your handbag. You can only lock the keypad when

the flip is closed.

• Locking the keypad

In standby mode, press Menu and then

within 1.5 seconds.

• Unlocking the keypad

Press Unlock and then

within 1.5 seconds or open the flip. Note that the

keyguard will not be activated when if you close the flip, if the automatic

keyguard is not activated.

To answer a call when the keyguard is on, press

. During a call, the phone can

be operated normally. When you end or reject the call, the keypad will

automatically lock, if the display is empty.

For locking the keypad during a call, see Options during a call on page 49, and for

setting the security keyguard, see Security keyguard in Phone settings on page

128.

Note: When Keyguard is on, calls may be possible to the emergency number

programmed into your phone (e.g. 112 or other official emergency number). Key in

the emergency number and press

keyed in its last digit.

. The number is displayed only after you have

■ Over-the-air settings service

In order to use MMS, EGPRS, and other wireless services, you need to have proper

connection settings on your phone. You may be able to receive the settings

directly as an over-the-air message and then save them on your phone. For more

information on the availability of the settings, contact your network operator,

service provider or the nearest authorised Nokia dealer.

You may be able to receive the connection settings for EGPRS, multimedia

messages, synchronisation, chat and presence, e-mail and for the multi-mode

browser. For more information about receiving the settings, see Settings for the e-

mail application on page 76.

When you have received the connection settings as an over-the-air message

Connection settings received is displayed.

• To save the settings, press Options and select Save. If the phone asks you to

Enter settings’ PIN:, key in the PIN code for the settings and press OK. For the

availability of the PIN code, contact the service provider that supplies the

settings.

If no settings have been saved yet, the settings are saved under the first free

connection set.

• To view the received settings first, press Options and select View. To save the

settings, press Save.

• To discard the received settings, press Options and select Discard.

To activate the settings, see Connecting to a service on page 160.

If you want to delete a connection set from the phone, key in *#335738#

(*#delset# in letters) in standby mode, select a connection set that you want to

delete and press Delete. Then confirm your selection and the phone returns to

standby mode.

3. Call functions

■ Making a call

1. Key in the phone number, including the area code. If you key in an incorrect

character, press Clear to delete it. To make a call when the flip is open, key in

the phone number using the number keys. The loudspeaker is always activated,

when you open the flip.

For international calls, press

twice for the international prefix or + if the

flip is open, (the + character replaces the international access code) and then

key in the country code, the area code without the leading 0, if necessary, and

finally the phone number.

2. Press

to call the number.

To adjust the volume during a call, use the volume key on the side of the phone.

3. Press

to end the call or to cancel the call attempt.

See also Options during a call on page 49.

Making a call using contacts

• To search for a name/phone number that you have saved in Contacts See

Searching for a contact on page 103. Press

to call the number on the

display.

Last number redialling

• In standby mode, press

once to access the list of upto 20 last numbers you

called or attempted to call. Scroll to the number or name that you want, and

press to call the number.

Calling your voice mailbox (network service)

• In standby mode when the flip is closed, press and hold

, or press

and

. When the flip is open, press and hold the corresponding number key

on the keyboard.

If the phone requests the voice mailbox number, key it in and press OK. See

also Voice messages on page 89.

Speed dialling a phone number

Before you can use speed dialling, proceed as follows:

Press Menu, select Settings, More settings,Call settings and Speed dialling. Set the

setting to On.

Assign a phone number to one of the speed-dialling keys from

Speed dials on page 110. Call the number in either of the following ways:

• Press the speed dialling key you want and then press . You can also activate

, see

speed dialling by pressing the corresponding number key on the keyboard,

when the flip is open.

• If Speed dialling is set to on, press and hold a speed-dialling key until the call is

started.

■ Answering or rejecting an incoming call

Press

to answer an incoming call and press

to end the call.

Press

to reject an incoming call.

If you press Silence, only the ringing tone is muted. Then either answer or reject

the call.

If a compatible headset with the headset key is connected to the phone, you can

answer and end a call by pressing the headset key.

Tip: If the Divert if busy function has been activated to divert calls, for

example to your voice mailbox, rejecting an incoming call will also divert

the call. See Call settings on page 126.

Note that when somebody is calling you, the phone shows the caller’s name,

phone number, or the text Private number or Call. If more than one name is found

in Contacts with a phone number having the same seven last digits as the caller’s

number, only the phone number will be displayed, if it is available. The phone may

display an incorrect name, if the caller’s number has not been saved in Contacts

but there is another name saved whose phone number has the same seven last

digits as the phone number of the caller.

Call waiting

Call waiting is a network service.

During a call, press

to answer the waiting call. The first call is put on hold.

Press to end the active call.

To activate the Call waiting function, see Call settings on page 126.

■ Options during a call

Note that some of the options during a call are network services. For availability,

contact your network operator or service provider. Press Options during a call and

select:

•

Lock keypad, Record, End call, New call (network service), End all calls,

Contacts, Menu, Mute or Unmute, Hold or Unhold (network service), Private

call (network service), Answer and Reject.

•

Conference to make a conference call that allows up to five people to

participate in a conference call (network service). During a call, make a call to a

new participant (New call). The first call is put on hold. When the new call has

been answered, select Conference to include the first participant in the call. To

have a private conversation with one of the participants, select Private call and

select the participant. To rejoin the conference call after a private

conversation, select Conference.

•

Send DTMF to send DTMF (Dual Tone Multi-Frequency) tone strings, for

example passwords or bank account numbers. The DTMF system is used by all

touch-tone telephones. Key in the DTMF string, or search for it in Contacts.

Note that you can key in the wait character w and the pause character p by

repeatedly pressing

•

Swap (network service) to switch between the active call and the call on hold,

Transfer (network service) to connect a call on hold to an active call and to

disconnect yourself from the calls.

Loudspeaker to use your phone as a loudspeaker during a call, such as a

conference call. In addition, you can use the loudspeaker to carry out other

tasks simultaneously, since you can put the phone down instead of holding it

in your hand. Do not hold the phone to your ear during loudspeaker operation,

as the volume may be extremely loud. To activate the loudspeaker, open the

flip or, if the flip is closed, press Options and select Loudspeaker or press

Loudsp., if available.

To deactivate the loudspeaker during a call, close the flip or press Normal,

when the flip is open. When the flip is closed, press Options and select Handset

or press Normal, if available

The loudspeaker is deactivated automatically when you end the call or call

attempt, connect a compatible handsfree unit or a headset to the phone, or

close the flip.

If you have connected a compatible handsfree unit or a headset to the phone,

Handset in the options list is replaced with Handsfree or Headset and the

selection key Normal with Handsf. or Heads., respectively.

Using the loudspeaker with the stereo radio, see Radio (Menu 6) on page 135.

4. Writing text

Your phone is especially designed for easy and comfortable text writing. A good

way is to write with your thumbs using the messaging keyboard. You can, for

example start writing a message using the keyboard, close the flip and continue

writing with either traditional or predictive text input. Note that predictive text

input is not available, when the flip is open.

■ Writing text using the messaging keyboard

When the flip is open, you can start to write a message or a note.

For example, press Menuand select Messages, Text messages and Create message,

see Writing and sending messages on page 63.

Tip: To quickly start writing a message move the joystick to the left in

standby mode.

Or: Press any of the letter keys in standby mode (except the pause character p or

the wait character w) to open the Notes application, see Notes on page 142.

The following functions are available when writing text, while the flip is open:

• To insert a number, press any of the number keys. Pressing a number key in

standby mode initiates a normal call procedure.

• To switch between lower and upper-case letters, indicated by

on the top left of the display, or to key in symbols, press either

on the keyboard. You can either press the shift key and the desired

character consecutively, or press and hold both the shift key and the desired

letter key at the same time. To write in upper case only, press

twice.

• To delete characters from the display, press

or Clear. Pressing backspace

briefly clears one character at a time, while a longer keypress deletes

characters more quickly.

• To add a space, press one of the space keys

• To force a line break, press

Typing accented characters

The characters available depend on the language selected in the Phone language

menu, see Phone settings on page 128. To type accented characters or symbols

that are not printed on the keyboard, do one of the following:

• To access a set of punctuation marks, accented characters and symbols, press

. Scroll through the character set by moving the joystick and press Use to

select the character.

• To type an accented character that is not included in the list of special

characters under

, such as á, press and hold

and simultaneously press ’a’

repeatedly until the desired accented variant of ’a’ appears on the display.

■ Writing text when the flip is closed

You can use predictive or traditional text input when the phone’s flip is closed.

During writing, predictive text input is indicated by

and traditional text

input by

indicated by

on the top left of the display. You can change the character case,

or by pressing . The number mode is

, and you can change between letter and number modes by

pressing and holding

Setting predictive text input on or off

When writing text, press Options and select Dictionary.

• To set the predictive text input on, select a language from the dictionary

options list. Predictive text input is only available for the languages on the list.

• To revert to traditional text input, select Dictionary off.

Tip: To quickly set the predictive text input on or off when writing text,

press

twice, or press and hold Options.

Using predictive text input

You can key in any letter with a single keypress. Predictive text input is based on a

built-in dictionary to which you can also add new words.

1. Start writing a word using the keys

. Press each key only once

for one letter. The word may change after each keystroke.

Example: To write Nokia when the English dictionary is selected, press

once for N,

once for o,

once for k,

once for i

and

once for a.

To insert a number while in letter mode, press and hold the desired number key.

For more instructions for writing text, see Tips for writing text on page 55.

2. When you have finished writing the word and it is correct, confirm it by space

with or by moving the joystick to the right.

If the word is not the one you are looking for, press

repeatedly or press

Options and select Matches. When the word you want appears, confirm it.

3. If the ? character is displayed after the word, the word that you intended to

write is not in the dictionary. To add the word to the dictionary, press Spell, key

in the word (traditional text input is used) and press Save. When the dictionary

becomes full, the new word replaces the oldest one that was added.

4. Start writing the next word.

Writing compound words

Key in the first part of the word and confirm it by moving the joystick to the right.

Write the last part of the word and confirm it by moving the joystick to the right.

Using traditional text input

Press a number key,

, repeatedly until the desired character appears.

Not all characters available under a number key are printed on the key. The

characters available depend on the language selected in the Phone language

menu, see Phone settings on page 128.

To insert a number while in letter mode, press and hold the desired number key.

• If the next letter you want is located on the same key as the present one, wait

until the cursor appears, or move the joystick to the right, and then key in the

letter.

•

The most common punctuation marks and special characters are available

under the number key

For more instructions for writing text, see Tips for writing text on page 55.

Tips for writing text

The following functions may also be available for writing text in predictive or

traditional input:

• To insert a space, press

• To move the cursor to the right, left, up or down, move the joystick

correspondingly.

• To delete a character from the display, press Clear. Press and hold Clear to

delete the characters more quickly.

To delete all the characters simultaneously when writing a message, press

Options and select Clear text.

• To insert a word that is not in the dictionary when using predictive text input,

press Options and select Insert word. Write the word using traditional text

input and press Save. The word is also added to the dictionary.

• To insert a special character when using traditional text input, press

when using predictive text input, press and hold

, or press Options and

select Insert symbol.

Move the cursor with the joystick to a character and press Use to select it.

You can also scroll to a character by pressing

select it by pressing

, and

The following options are available when writing text messages:

• To insert a phone number while in letter mode, press Options and select Insert

number. Key in the number or search for it in Contacts and press OK.

• To insert a name from Contacts, press Options and select Insert contact. To

insert a phone number or a text item attached to the name, press Options and

select View details.

5. Using the menu

The phone offers you an extensive range of functions, which are grouped into

menus. Most of the menu functions are provided with a brief help text. To view

the help text, scroll to the menu function you want and wait for 15 seconds. To

exit the help text, press Back. See Phone settings on page 128.

■ Accessing a menu function

By scrolling

1. To access the menu, press Menu.

2. Scroll through the menu by moving the joystick up or down (or right and left if

the grid menu is selected), and select, for example, Settings by pressing Select.

To change the menu view, see Display settings on page 117.

3. If the menu contains submenus, select the one you require, for example

Profiles.

4. If the selected submenu contains further submenus, repeat step 3. Select the

next submenu, for example Anykey answer.

5. Select the setting of your choice.

6. Press Back to return to the previous menu level, and Exit to exit the menu.

By using a shortcut

The menus, submenus and setting options are numbered and you can access most

of them by using their shortcut number.

• To access the menu, press Menu. Key in quickly, within two seconds, the index

number of the menu function you want to access. Note that to access the

menu functions in menu 1, press Menu,

and then key in the rest of

the desired shortcut number.

Press Back to return to the previous menu level, and Exit to exit the menu.

■ List of menu functions

1. Messages

1. Text messages

2. Multimedia msgs.

3. E-mail

4. Chat

5. Voice messages

6. Info messages

7. Message settings

8. Service commands

2. Call register

1. Missed calls

2. Received calls

3. Dialled numbers

4. Delete recent call lists

5. Timers and counters

3. Contacts

1. Search

2. Add contact

3. Delete

4. My presence

5. Subscribed names

6. Copy

7. Settings

8. Speed dials

9. Voice tags

10.Info numbers

11.Service numbers ¹

12.My numbers

13.Caller groups

4. Settings

1. Profiles

2. Chat and my presence settings

3. Tone settings

4. Display settings

5. Time and date settings

6. Personal shortcuts

7. Connectivity

8. More settings

9. Restore factory settings

5. Gallery

1. Video clips

2. Graphics

3. Tones

1. Shown if supported by your SIM card. For availability, contact your network operator or serv-

ice provider.

4. Recordings

6. Radio

7. Organiser

1. Alarm clock

2. Calendar

3. To-do list

4. Notes

5. Wallet

6. Synchronisation

8. Applications

1. Games

2. Collection

3. Extras

9. Services

1. Home

2. Bookmarks

3. Download links

4. Service inbox

5. Settings

6. Go to address

7. Clear the cache

10.SIM services

1. Only shown if supported by your SIM card. The name and contents vary depending on the SIM

card.

6. Menu functions

■ Messages (Menu 1)

You can read, write, send and save text, multimedia, and e-mail

messages. All messages are organised in folders.

Before you can send any text, picture or text (SMS) e-mail messages, you need to

save your message centre number, see Message settings on page 90.

Text messages (SMS)

Using SMS (Short Message Service), your phone can send and receive multi-part

messages which consist of several ordinary text messages (network service). This

may affect the invoicing of the messages.

You can also send and receive text messages that contain pictures.

The text messages function uses shared memory, see Shared memory on page 23.

Note: The picture message function can be used only if it is supported by your

network operator or service provider. Only phones that offer picture message

features can receive and display picture messages.

Writing and sending messages

The number of available characters and the current part number of a multi-part

message are shown on the top right of the display, for example 120/2. Special

(Unicode) characters, such as á, may take up more space in the message than

other characters.

1. Press Menu and select Messages, Text messages and Create message.

Tip: To quickly start writing a message, move the joystick to the left in

standby mode.

2. Key in a message, see Writing text on page 51. Use a template to insert text or

a picture into the message, see Templates on page 68. Each picture message

comprises several text messages. Therefore, sending one picture message may

cost more than sending one text message.

3. To send the message, press Send or

4. Enter the recipient’s phone number or search for it in Contacts, and press OKto

send the message.

Options for sending a message

After you have written a message, press Options and select Sending options.

• To send a message to several recipients, select Send to many. Select the

recipients one by one and press Send after each selection. When you have sent

the message to everyone you want to send it to, press Done. Note that a

separate message is sent to each recipient.

• To send a message using a distribution list, select Send to list. To create a

distribution list, see Distribution lists on page 69.

• To send a message using a message profile, select Sending profile and the

desired message profile. For defining a message profile, see Message settings

on page 90.

Note: When sending messages via the SMS network service, your phone may

display the words "Message sent". This is an indication that the message has been

sent by your phone to the message centre number programmed into your phone.

This is not an indication that the message has been received at the intended

destination. For more details about SMS services, check with your service provider.

Writing and sending e-mail via SMS

Before you can send an e-mail via SMS, you need to save the settings for sending

e-mail, see Message settings on page 90. For availability and subscription to the

e-mail service, contact your network operator or service provider. To save an e-

mail address in Contacts, see Saving multiple numbers and text items per name on

page 101.

1. Press Menu, and select Messages, Text messages and Create SMS e-mail.

2. Key in the recipient’s e-mail address or search for it in Contacts and press OK.

3. If you wish, you can key in a subject for the e-mail and press OK.

4. Key in the e-mail message. See Writing text on page 51. The total number of

characters that you can key in is shown on the top right of the display. The e-

mail address and subject are included in the total number of characters.

See also Templates on page 68. Pictures cannot be inserted.

5. To send the e-mail, press Send or

. If you have not saved the settings for

sending e-mails, the phone requests the number of the e-mail server. Press OK

to send the e-mail.

Note: When sending e-mails via the SMS network service, your phone may display

the words Message sent. This is an indication that the e-mail has been sent by your

phone to the e-mail server. This is not an indication that the e-mail has been

received at the intended destination. For more details about e-mail services, check

with your service provider.

Reading and replying to an SMS message or an SMS e-mail

When you have received a message or an e-mail, the indicator

and the

number of new messages followed by messages received are shown.

The blinking indicates that the message memory is full. Before you can

receive new messages, delete some of your old messages from the Inbox folder.

1. Press Show to view the new message, or press Exit to view it later.

Reading the message later:

Press Menu, select Messages, Text messages and Inbox.

2. If more than one message has been received, select the one that you want to

read. An unread text message is indicated by

in front of it.

3. While reading or viewing the message, press Options.

You can select an option, for example, to delete, forward or edit the message

as a text message or an e-mail, rename the message you are reading or move it

to another folder.

Select Copy to calendar to copy text from the beginning of the message to your

phone’s calendar as a memo for the current day.

Select Message details to view, if available, the sender’s name and phone

number, the message centre used, and the date and time of receipt.

Select Use detail to extract numbers, e-mail and website addresses from the

current message.

When viewing a picture message, select Save picture to save the picture in the

Templates folder.

4. Press Reply to reply to a message. Select Original text to include the original

message in the reply, or select a standard answer to be included in the reply, or

select Empty screen.

When replying to an e-mail, confirm or edit the e-mail address and subject

first. Then write your reply message.

5. Press Send or

to send the message to the displayed number.

Inbox and sent items folders

The phone saves incoming text messages in the Inbox folder and sent messages in

the Sent items folder of the Text messages submenu.

Text messages that you wish to send later can be saved in the Saved items or

Templates folder, or in any folder you have created.

Archive folder and my folders

To organise your messages, you can move some of them to the Saved items folder,

or add new folders for your messages.

While reading a message, press Options. Select Move, scroll to the folder to which

you want to move the message and press Select.

To add or delete a folder, press Menu, select Messages, Text messages and My

folders.

• To add a folder, press Options and select Add folder. If you have not saved any

folders, press Add to create one.

• To delete a folder, scroll to the folder that you want to delete, press Options

and select Delete folder.

Templates

Your phone includes text templates, indicated by

, and picture templates,

indicated by

To access the template list, press Menu and select Messages, Text messages and

Templates.

• To insert a text template into a message or an e-mail that you are writing or

replying to, press Options. Select Use template and select the template that

you want to insert.

• To insert a picture into a text message that you are writing or replying to, press

Options. Select Insert picture and select a picture to view it. Press Insert to

insert the picture into your message. The

indicator in the header of the

message indicates that a picture has been attached. The number of characters

that you can include in a message depends on the size of the picture.

To view the text and the picture together before sending the message, press

Options and select Preview.

Distribution lists

If you need to send messages frequently to a fixed group of people, you can define

a distribution list for that purpose. You can save to the distribution lists contacts

stored both in the phone’s and in the SIM card’s memory. Note that the phone

sends the message separately to each recipient on the list. Therefore, sending a

message using a distribution list may cost more than sending a message to one

recipient.

Make sure that the contacts that you want to add to the distribution lists are

saved in the phone’s internal contact memory.

Distribution lists use shared memory, see Shared memory on page 23.

1. Press Menu in standby mode, and select Messages, Text messages and

Distribution lists.

2. To create a new list, press Add if there are no distribution lists, or press Options

and select Add list if you have already created distribution lists.

To view the names on a list, scroll to the desired list and press View.

To rename a list, clear it or delete it, press Options, and select the appropriate

function.

3. If you opened a distribution list by pressing View in step 2, you can do one of

the following:

• To add a new name to the list, press Add and select the desired name from

Contacts.

• To view the contact information of a recipient, scroll to the desired name,

press Options and select View details.

• To delete a recipient from the list, scroll to the desired name, press Options

and select Delete contact.

If the message fails to be sent to certain recipients on the distribution list, failed

messages are listed in the Undelivered folder. Press Resend to send the message

again, or press Options and select Delete list to delete the Undelivered list or View

message.

Text message counter

Text message counter shows the number of received and sent text and picture

messages. Picture messages may consist of more than one message. You can, for

example, view the recipient or sender of the message or view the details of the

message.

Multimedia messages

Note: This function can be used only if it is supported by your network operator or

service provider. Only phones that offer compatible multimedia message features

can receive and display multimedia messages.

A multimedia message can contain text, one image, one sound clip, one

video clip or slides. The phone supports multimedia messages that are up to 100

kB in size. If the maximum size is exceeded, the phone may not be able to receive

the message. Depending on the network, you may receive a text message that

includes an Internet address where you can view the multimedia message on the

PC.

If the message contains an image, the phone may scale it down to fit the display

area.

The multimedia function uses shared memory, see Shared memory on page 23.

from being copied, modified, transferred or forwarded.

Note: If Allow multimedia reception is set to Yes or In home network, your operator

or service provider may charge you for every message you receive.

Multimedia messaging supports the following formats:

• Image: JPEG, GIF, WBMP, BMP, PNG and OTA-BMP

• Sound: Scalable Polyphonic MIDI (SP-MIDI), AMR audio and monophonic

ringing tones

• Video clips in H.263 format with SubQCIF image size and AMR audio.

The phone does not necessarily support all variations of the aforementioned file

formats. If a received message contains any unsupported elements, they may be

replaced with the file name and the text Object format not supported.

Note that you cannot receive any multimedia messages if you have a call in

progress, a game or another Java application running, or an active browsing

session over GSM data (see Keying in the service settings manually on page 160).

Because delivery of multimedia messages can fail for a variety of reasons, do not

rely solely upon them for essential communications.

Writing and sending a multimedia message

For defining the settings for multimedia messaging, see Settings for multimedia

messages on page 91. For availability and subscription to the multimedia

messaging service, contact your network operator or service provider.

1. Press Menu and select Messages, Multimedia msgs. and Create message.

2. Key in a message, see Writing text on page 51.

• To insert a file into the message, press Options, select Insert and select the

desired option. The list of available folders in the Gallery menu is shown.

Open the specific folder, scroll to the desired file, press Options and select

Insert. An attached file is indicated by the file name in the message.

• Your phone supports the sending and receiving of multimedia messages

that contain several pages (‘slides’). To insert a slide into the message, press

Options, select Insert and Slide. Each slide can contain text, one image, one

video clip and one sound clip.

• If the message contains several slides, you can open the desired one by

pressing Options and selecting Previous slide, Next slide or Slide list.

• To set the interval between the slides, press Options and select Slide timing.

• To move the text part to the top or bottom of the message, press Options

and select Text on top or Text on bottom.

• To insert a name from Contacts, press Options, select More options, Insert

contact and scroll to the desired name and select it.

• To insert a number, press Options, select More options and Insert number.

Key in the number or search for it in Contacts and press OK.

3. To view the message before sending it, press Options and select Preview.

4. Press Send or to send the message, or press Options and select Send to e-

mail or Send to many.

5. Enter the recipient’s phone number (or e-mail address) or search for it in

Contacts. Press OK and the message is moved to the Outbox folder for sending.

It takes more time to send a multimedia message than a text message. While

the multimedia message is being sent, the animated indicator

is displayed

and you can use other functions on the phone. If there is an interruption while

the message is being sent, the phone tries to resend it a few times. If this fails,

the message will remain in the Outbox folder and you can try to resend it later.

The messages that you have sent will be saved in the Sent items folder if the

setting Save sent messages is set to Yes, see Settings for multimedia messages

on page 91. The fact that a message is sent is not an indication that the

message has been received at the intended destination.

Reading and replying to a multimedia message

When your phone is receiving a multimedia message, the animated indicator

is displayed. When the message has been received, the indicator

and the text

Multimedia message received are shown.

The blinking

indicates that the memory for multimedia messages is full, see

Multimedia messages memory full on page 75.

The multimedia message function uses shared memory, see Shared memory on

page 23.

1. Press Show to view the message, or press Exit to view it later.

Reading the message later: Press Menu and select Messages, Multimedia

msgs. and Inbox. Scroll to view the message.

2. Press Select to view the message. The function of the middle selection key

changes according to the displayed object.

• To reply to the message, press Reply.

• To delete an object contained in the message, press Delete. Otherwise, press

Options and select Delete message.

• if the received message contains a presentation, press Play to view the

message.

Otherwise, press Play to listen to a sound clip or view the video clip

contained in the message, or press Zoom to zoom in on an attached image

or press View to view a business card or a calendar note.

If you press Options, some of the following options are available:

•

Delete message to delete a saved message.

Reply or Reply to all to reply to the message. To send the reply, see Writing

and sending a multimedia message on page 72.

•

Use detail to extract phone numbers, e-mail or web addresses from the

current message.

•

Forward to no., Forward to e-mail or Send to many to forward the message.

Edit to edit a message that you have written. See Writing and sending a

multimedia message on page 72.

•

Message details to view the subject, size and class of the message.

•

Play presentation to view the presentation contained in the message.

Open calend. note or Open bus. card to view a calendar note or a business

card.

See also the options in Gallery, see Gallery (Menu 5) on page 132.

Inbox, Outbox, Saved and Sent items folders

The phone saves the multimedia messages that have been received in the Inbox

folder of the Multimedia msgs. submenu.

Multimedia messages that have not yet been sent are moved to the Outbox folder

of the Multimedia msgs. submenu.

The multimedia messages that you wish to send later can be saved in the Saved

items folder of the Multimedia msgs. submenu.

The multimedia messages that have been sent are saved in the Sent items folder of

the Multimedia msgs. submenu, if the setting Save sent messages is set to Yes, see

Settings for multimedia messages on page 91.

Multimedia messages memory full

When you have a new multimedia message waiting and the memory for the

messages is full, the indicator

blinks and Multimedia memory full, view

waiting msg. is shown. To view the waiting message, press Show. To save the

message, press Save and delete old messages by first selecting the folder and then

the message to be deleted.

To discard the waiting message, press Exit and Yes. If you press No, you can view

the message.

Deleting messages

• To delete text messages, press Menu and select Messages, Text messages and

Delete messages.

To delete all messages from all folders, select All messages and when Delete all

messages from all folders? is displayed, press Yes. If the folders contain unread

messages, the phone will ask whether you want to delete them also.

To delete multimedia messages, press Menu and select Messages, Multimedia

msgs. and Delete messages.

• To delete all messages from a folder, select the folder from which you want to

delete the messages and press Yes. If the folder contains unread messages, the

phone will ask whether you want to delete them also.

E-mail application

The e-mail application allows you to access your e-mail account via the phone.

The compatible e-mail system that you use in the office or at home may be

supported by the e-mail function on your phone. You can write, send, and read e-

mails with your phone. Your phone supports POP3 and IMAP4 e-mail servers.

The e-mail function uses shared memory, see Shared memory on page 23.

Before you can send and retrieve any e-mails, you may need to do the following:

• Obtain a new e-mail account or use the current one. To check the availability

of your e-mail account, contact your e-mail service provider.

• For the settings required for e-mail, contact your network operator or e-mail

service provider. For receiving the e-mail settings over the air, see Over-the-air

settings service on page 44.

• To set the e-mail settings on your phone, press Menu and select Messages,

Message settings and E-mail messages. See Settings for the e-mail application

on page 92.

Writing and sending messages with the e-mail application

You can write your e-mail message before connecting to the e-mail service, or

connect to the service first, and then write and send your e-mail.

1. Press Menu and select Messages, E-mail, and Create e-mail.

2. Key in the recipient’s e-mail address and press OK or press Edit and key in the

e-mail address, and press OK.

To search for the e-mail address in Contacts, press Options, and select Search.

3. You can key in a subject for the e-mail if you want, and press OK.

If you press Options, you can select one of the following: the message editor,

add a new recipient, add a copy recipient or a hidden copy recipient.

4. Press Options and select Message editor. Key in the e-mail message, see

Writing text on page 51. The number of characters that you can key in is shown

on the top right corner of the display.

5. To send the e-mail message, press Send. Select

•

Send now to send the e-mail immediately. If you have not already

connected to the e-mail account, your phone establishes the connection

first and then sends the e-mail.

Send later to send your e-mail later and the e-mail is saved in the Outbox

folder. If you want to edit or continue writing your e-mail later, you can

save it in Drafts by selecting Save draft msg..

Sending the e-mail later: Press Menu and select Messages, E-mail, Other

options, and Send now or Retrieve and send.

Note: When sending e-mails, your phone may display the words Message sent.

This is an indication that the e-mail has been sent by your phone to the e-mail

server. This is not an indication that the e-mail has been received at the intended

destination. For more details about e-mail services, check with your service

provider.

Downloading messages from your e-mail account using the e-mail

application

1. Press Menu and select Messages, E-mail, and Retrieve to download e-mail

messages that have been sent to your e-mail account. Or:

Press Menu and select Messages, E-mail, Other options, and Retrieve and send

to download new e-mail messages and to send e-mails that have been saved in

the Outbox folder.

If the message memory is full, delete some of your older messages before you

start to download new messages.

2. Your phone makes a connection to the e-mail service. A status bar is shown

while your phone is downloading e-mail messages to your phone.

3. Press Select to view the new message in Inbox, or press Back to view it later.

If more than one message is received, select the message that you want to

read. An unread text message is indicated by

Reading and replying to a message with the e-mail application

1. Press Menu, select Messages, E-mail and Inbox.

2. While reading the message, press Options.

You can, for example, view the details of the selected message, mark the

message as unread, delete, reply, reply to all, forward or move the message to

another folder.

3. To reply to an e-mail, press Reply. Select Original text to include the original

message in the reply or select Empty screen.

When replying to an e-mail, write your reply and edit the e-mail address and

subject, if necessary.

4. To send the message, press Send and select Send now.

Inbox and Other folders (Drafts, Archive, Outbox and Sent items)

Your phone has the following folders in the E-mail menu:

•

Inbox for saving e-mails that you have downloaded from your e-mail account.

Other folders contains the folders: Drafts for saving unfinished e-mails,

Archive for organising and saving your e-mails, Outbox for saving e-mails that

have not been sent, if you have selected Send later, see Writing and sending

messages with the e-mail application on page 77, and Sent items for saving e-

mails that have been sent.

Deleting messages using the e-mail application

• To delete e-mail messages, press Menu and select Messages, E-mail, Other

options and Delete messages.

To delete all messages from a folder, select the folder from which you want to

delete the messages and press Yes. To delete all messages from all folders,

select All messages and press Yes.

Note that deleting an e-mail from your phone does not delete it from the e-

mail server.

Chat

Note: This function can be used only if it is supported by your network operator or

service provider. Only phones that offer compatible chat features can receive and

display chat messages.

Chat is a way of sending short text messages that are delivered over TCP/IP

protocols to online users (network service). Your contact list shows you when the

contacts on the list are online and available to participate in a chat conversation.

When you have written and sent your message, it remains on the display. The reply

message appears above your original message.

Before you can use chat, you need to subscribe to the service. For availability,

charging and subscription to the service, contact your network operator or service

provider, from whom you also receive your unique ID and password and the chat

settings.

To set the required chat service settings, see Chat and my presence settings on

page 115.

You can use the other phone functions, while you have an active chat session in

the background. Depending on the network, the active chat session may consume

the phone’s battery faster and you may need to connect the phone to a charger.

Chat uses shared memory, see Shared memory on page 23.

Basic steps for chat

• To enter the chat menu (offline), see Entering the chat menu on page 82.

• To connect to the chat service (online), see Connecting to and disconnecting

from the chat service on page 83.

• To start a chat session with a contact, see Chat contacts in Starting a chat

session on page 83.

To create you own chat contact lists, see Contacts for the chat session on page

87.

• To join a public chat session, see Groups in Starting a chat session on page 83.

To join a group chat session via an invitation message, see Accepting or

rejecting a chat invitation on page 84.

To create your own chat groups, or to join or delete a public group, see Groups

on page 88.

• To edit your own information, see Editing your own information on page 86.

• To search users and groups, see Search in Starting a chat session on page 83.

• To read a message in a new chat session, see Reading a chat message on page

85.

• To write and send messages during an active chat session, see Participating in

a chat conversation on page 86.

• To view, rename or delete saved conversations, select Saved convers. when you

have entered the Chat menu.

• To block/unblock contacts, see Blocking and unblocking messages on page 87.

• To disconnect from the chat service, see Connecting to and disconnecting from

the chat service on page 83.

Entering the chat menu

To enter the Chat menu while still offline, press Menu, and select Messages and

Chat. You can select

•

To set the phone to automatically connect to the chat service when you enter

the Chat menu, see Connecting to and disconnecting from the chat service on

page 83.

•

Saved convers. to view, erase or rename the chat conversations that you have

saved during the chat session. You can select Saved convers. also when you

have connected to the chat service.

Connect. settings to edit the settings needed for chat messaging and presence

connection. See Chat and my presence settings on page 115. You can also

select Connect. settings when you have connected to the chat service.

Connecting to and disconnecting from the chat service

To connect to the chat service, enter the Chat menu, and select Login. When the

phone has successfully connected, Logged in is displayed.

Tip: To set the phone to automatically connect to the chat service each

time you enter the Chat menu, connect to the chat service, select My

settings, Automatic login and On Chat start-up.

To disconnect from the chat service, select Logout.

Starting a chat session

Enter the Chat menu and connect to the chat service. You can select

•

Conversations to view the list of new and read chats or invitations to chats

during the active chat session. Scroll to the message or invitation that you

want and press Open to read the message.

indicates new and

indicates invitations.

read chat messages.

read group messages.

•

Chat contacts includes the contacts that you have added from the phone’s

contacts memory. Scroll to the contact with whom you would like to chat and

press Chat.

If you have received a new message from a contact, it is indicated by

indicates the online and the offline contacts in the phone’s contacts

memory.

indicates a blocked contact, see Blocking and unblocking messages on

page 87.

To add contacts to the list, see Contacts for the chat session on page 87.

•

Groups and Public groups. The list of bookmarks to public groups provided by

the network operator or service provider is displayed. To start a chat session

with a group, scroll to a group and press Join. Enter the screen name that you

want to use in the conversation. When you have successfully joined the group

conversation, the phone shows Joined group: and the group name. To create a

private group, see Groups on page 88.

Search and select Users or Groups to search for other chat users or public

groups on the network.

• If you select Users, you can search for a user by phone number, screen

name, e-mail address or name.

• If you select Groups , you can search for a group by a group member, group

name, topic or ID.

To start the chat session when you have found the user or the group, scroll to

the user or the group that you want, press Options and select Chat or Join

group.

• To start a chat session from Contacts, see Viewing the subscribed contacts on

page 108.

Accepting or rejecting a chat invitation

In standby mode, when you have connected to the chat service and you receive an

invitation, New invitation received is displayed. Press Read to read it.

If you receive more than one invitation, the number of messages followed by new

invitations received is displayed. Press Read, scroll to the invitation you want, and

press Open.

• To join the private group conversation, press Accept. Enter the screen name

that you want to use as a nickname. When you have successfully joined the

group, the phone shows Joined group: and the group name.

• To reject or delete the invitation, press Options and select Reject or Delete.

Reading a chat message

In standby mode, when you have connected to the chat service and you receive a

message from a person who is not taking part in the conversation, New instant

message is displayed. Press Read to read it.

• If you receive more than one message, the number of messages followed by

new instant messages is displayed. Press Read, scroll to the message, and press

Open.

New messages received during an active chat session are held in the

Conversations of the Chat menu. If the message is from a person whose contact

information is missing from the contact list in Chat contacts, the sender’s ID is

shown. If the contact information can be found in the phone’s memory for

contacts and the phone recognises it, the sender’s name is shown. To save a new

contact in the phone’s memory, press Options and select

•

Save contact and enter the name of the person.

Add to contact and select the contact to which you want to add the detail and

press Add.

Participating in a chat conversation

Join or start a chat session by pressing Write.

Tip: If you receive a new message during a chat session from a person who

is not participating in the current chat session, the indicator

is shown

on the top of the display.

Write your message and press Send or

to send it. If you press Options, some of

the following options are available.

•

View conversation to view the ongoing chat conversation. To save the chat

conversation, press Save and enter the name for the conversation.

Save contact, see Reading a chat message on page 85.

Add to contact, see Reading a chat message on page 85.

•

Group members to view the members of the selected private group. The option

is only shown if you have created the group.

•

End conversation to end the ongoing conversation.

Dictionary, see Setting predictive text input on or off on page 53.

Editing your own information

Enter the Chat menu and connect to the chat service. Select My settings to view

or edit your own availability status or screen name. Select Availability and either

Available for all or Avail. for contacts (or Appear offline) to allow all chat users, or

only the contacts on your chat contact list to see whether you are online or offline

when you have connected to the chat service. The indicator

shows that you

are online and

that your online status is not visible to others.

Contacts for the chat session

You can add contacts from the phone’s contacts memory to the chat contacts list.

Connect to the chat service, select Chat contacts, press Options and select

•

Add contact, or if you have no contacts added, press Add. Select from Contacts

the name that you want to add to the list of chat contacts. When the contact is

added, the phone displays Added to Chat contacts: and the contact name.

Scroll to a contact, and press Chat to start to chat, or press Options and select

•

Contact info to view the details of the selected contact. If you want to edit the

details, see Editing or deleting details in contacts in the Contacts menu on

page 104.

•

Block contact (or Unblock contact) to block (or unblock) messages from the

selected contact.

•

Add contact to add a new contact from the phone’s contact memory.

Remove contact to remove a contact from the chat contact list.

Blocking and unblocking messages

Connect to the chat service and select Conversations or Chat contacts. Highlight

the contact in the contacts list from whom you want to block incoming messages.

Press Options, select Block contact and press OK.

To unblock messages, connect to the chat service and select Blocked list. Scroll to

the contact from whom you want to unblock the messages and press Unblock.

You can also unblock messages from the contact list, see Contacts for the chat

session on page 87.

Groups

You can create your own private groups for a chat session, or use the public

groups provided by the service provider. The private groups exist only during an

active chat session. You can add to a private group only the contacts that are in

your contact list and thus in the phone’s contacts memory, see Saving names and

phone numbers (Add contact) on page 100.

Public groups

You can bookmark public groups that your service provider may maintain.

Connect to the chat service, select Groups and Public groups. Scroll to a group

that you want to chat with and press Join. If you are not in the group, key in your

screen name as your nickname for the group. If you press Options, you can select

Delete group to delete a group from your group list.

Creating a private group

Connect to the chat service, select Groups and Create group. Key in the name for

the group and the screen name you want to use in the group. You can use a

different screen name in another group. Press Add to view the list of contacts.

Select a name from the contacts list to add it to the private group list. To add more

names to the list, press Options and select Add member and select a new name.

To remove a name from the private group list, scroll to it, press Options and select

Remove member.

To send an invitation to the new members that you have added to the group, press

Options and select Send invitation. Then write your invitation.

You can only select online contacts, indicated by

from the phone’s contacts

memory. Offline contacts are indicated by

Voice messages

The voice mailbox is a network service and you may need to subscribe to it. For

more information and for the voice mailbox number, contact your service

provider.

Press Menu and select Messages and Voice messages. Select

•

Listen to voice messages to call your voice mailbox at the phone number that

you have saved in the Voice mailbox number menu.

If you have two phone lines available (network service), each phone line may

have its own voice mailbox number, see Call settings on page 126.

•

Voice mailbox number to key in, search for or edit your voice mailbox number

and press OK to save it.

If supported by the network, the indicator

will indicate new voice messages.

Press Listen to call your voice mailbox number.

Tip: Pressing and holding

calls your voice mailbox, when the flip is

closed. When the flip is open, press and hold the corresponding number

key.

Info messages

With the info message network service, you can receive messagesfrom your

service operator on various topics that may include for example weather or traffic

conditions. For availability, topics and the relevant topic numbers, contact your

service provider.

Message settings

The message settings affect the sending, receiving and viewing of messages.

Settings for text and e-mail messages via SMS

1. Press Menu and select Messages, Message settings, Text messages and

Sending profile .

2. If more than one message profile set is supported by your SIM card, select the

set that you want to change.

• Select Message centre number to save the phone number of the message

centre that is required for sending text messages. You will receive this number

from your service provider.

• Select Messages sent via to select the message type: Text, E-mail, Paging or

Fax.

• Select Message validity to select the length of time for which the network

should attempt to deliver your message.

• For message type Text, select Default recipient number to save a default

number for sending messages for this message profile.

For message type E-mail, select E-mail server to save the e-mail server number.

• Select Delivery reports to ask the network to send delivery reports about your

messages (network service).

• Select Use GPRS and Yes to set GPRS as the preferred SMS bearer. Likewise, set

the GPRS connection setting to Always online, see EGPRS on page 123.

• Select Reply via same centre to allow the recipient of your message to send you

a reply via your message centre (network service).

• Select Rename sending profile to change the name of the selected message

profile. The message profile sets are only displayed if your SIM card supports

more than one set.

Overwrite settings

When the text message memory is full, the phone cannot receive or send any new

messages. However, you can set the phone to automatically replace old text

messages in the Inbox and Sent items folders with new ones.

Press Menu and select Messages, Message settings and Text messages. Select

either Overwriting in inbox or Overwriting in sent items and Allowed.

Settings for multimedia messages

You may receive the multimedia connection settings as an over-the-air message

from the network operator or service provider. To receive the settings over the air,

see Settings for the e-mail application on page 92.

Keying in the settings manually

Press Menu, and select Messages, Message settings and Multimedia msgs.. Select

•

Save sent messages. Select Yes to set the phone to save sent multimedia

messages in the Sent items folder. If you select No, the sent messages are not

saved.

•

Delivery reports to ask the network to send delivery reports about your

messages (network service).

Scale image down to define the image size when you insert the image into the

multimedia message.

•

Default slide timing to set the timing for slides in multimedia messages.

Allow multimedia reception. Select No, Yes or In home network to use the

multimedia service. If you select In home network, you cannot receive

multimedia messages outside your home network.

•

Incoming multimedia messages. Select Retrieve to set the phone to

automatically fetch newly received multimedia messages, or select Reject if

you do not wish to receive multimedia messages.

Connection settings. Define connection settings for retrieving multimedia

messages. First select Active multimedia settings, and activate the set in which

you want to save the settings. Select Edit active multimedia settings and edit

the active settings.

Select each of the settings one by one and key in all the required settings.

Contact your network operator or service provider for the settings.

•

Allow adverts. You can receive or reject messages identified as advertisements.

The setting is not shown if Allow multimedia reception is set to No.

Settings for the e-mail application

You may receive the e-mail settings from the network operator or service provider

over-the-air based on OMA (Open Mobile Alliance) provisioning. For more

information about using the OMA provisioning, contact your network operator or

service provider.

When you have ordered the settings as an OMA message, remain in standby mode

and do not open the E-mail application until you have received the settings.

When you have received the connection settings, E-mail settings received is

displayed. To save the settings immediately, select Start.

• To save the settings, select Save. Confirm the action by selecting Yes.

If all available settings are full, the phone asks if you want to replace an

existing set. Accept the replacement and select the set to be replaced.

The existing sets are located in the Messages, E-mail, Connect via menu.

The phone asks if you want to activate the saved settings. Accept the

activation if you want to use the new settings.

• To view the received settings first, select View.

• To discard the received settings, select Discard.

If the OMA provisioning service is not available, you can also key in the settings

manually. Press Menu and select Messages, Message settings, and E-mail

messages.

• First select Active e-mail settings and activate the set in which you want to

save the settings. Select Edit active e-mail settings and edit the active settings.

Select each of the settings one by one and key in all the required settings.

Contact your network operator or e-mail service provider for the settings.

•

Mailbox name. Key in the name that you want to use for the mailbox. You

can use any name.

•

E-mail address. Key in your e-mail address.

My name. Key in your name or nickname. Your name and e-mail address

will be shown.

•

Outgoing (SMTP) server. Key in the server address.

Incoming server type. Select either POP3 or IMAP4 depending on the type of

e-mail system that you are using. If both types are supported, select IMAP4.

Changing the server type also changes the incoming port number.

• If you have selected POP3 as a server type, then Incoming (POP3) server,

POP3 user name and POP3 password are shown. If you have selected IMAP4

as a server type, then Incoming (IMAP4) server, IMAP4 user name and

IMAP4 password are shown. Key in the e-mail server address for incoming

e-mail, then key in the user name and password to access the e-mail

account. If you have not defined an SMTP user name or SMTP password, the

e-mail server uses the POP3/IMAP4 user name and password instead.

•

Other settings and select:

•

Include signature. You can define a signature that is automatically

added to the end of your e-mail message.

•

Use SMTP authorisation. If your e-mail service provider requires

authentication for sending e-mails, select Yes. In this case, you must

also define your SMTP user name and SMTP password.

•

SMTP user name. Key in the user name for outgoing e-mail that you

have obtained from your e-mail service provider.

SMTP password. Key in the password that you want to use for outgoing

e-mail.

Outgoing (SMTP) port. Key in the number of the e-mail server port for

outgoing e-mail. The most common default value is 25.

If you have selected POP3 as the server type, the following options are

shown:

•

Incoming (POP3) port. Key in the port number that you have obtained

from your e-mail service provider.

Reply-to address. Key in the e-mail address to which you want the

replies to be sent.

Secure login. Select Secure login on if your connection requires an

encrypted login, otherwise leave it to Secure login off. Contact your

service provider if in doubt. Using encrypted login enables increased

security for user names and passwords. It does not increase security for

the connection itself.

•

Retrieve e-mails. Key in the maximum number of e-mails that you want

to retrieve at a time. The maximum number is 50.

Retrieval method. Select Latest if you want to retrieve all newly received

e-mails or select Latest unread if you want to retrieve only e-mails that

you have not read.

•

SMTP connection settings to define the connection settings required for

outgoing e-mail.

POP3 connection settings to define the connection settings for

incoming e-mail. See Keying in the service settings manually on page

160.

Select each of the settings one by one and key in all the required

settings. Contact your e-mail service provider for the settings.

If you have selected IMAP4 as the server type, the following options are

shown:

•

Incoming (IMAP4) port. Key in the port number that you have obtained

from your e-mail service provider.

Reply-to address. Key in the e-mail address to which you want the

replies to be sent.

Retrieve e-mails. Key in the number of e-mails that you want to retrieve

at a time. The maximum number is 50.

Retrieval method. Select Latest if you want to retrieve all newly received

e-mails or select Latest unread if you want to retrieve only e-mails that

you have not read.

•

SMTP connection settings to define the connection settings required for

outgoing e-mail.

IMAP4 connection settings to define the connection settings required

for incoming mail. See Keying in the service settings manually on page

160.

Select each of the settings one by one and key in all the required

settings. Contact your e-mail service provider for the settings.

Font size setting

To select the font size for reading and writing messages, press Menu and select

Messages, Message settings, Other settings, and Font size.

Service commands

Press Menu and select Messages and Service commands. Key in and send service

requests (also known as USSD commands), such as activation commands for

network services, to your service provider.

■ Call register (Menu 2)

The phone registers the phone numbers of missed, received and

dialled calls, and the approximate length of your calls.

The phone registers missed and received calls only if the network supports these

functions, and the phone is switched on and within the network’s service area.

When you press Options in the Missed calls, Received calls and Dialled numbers

menu, you can, for example, view the date and the time of the call, edit or delete

the phone number from the list, save the number in Contacts, or send a message

to the number.

Recent calls lists

Press Menu and select Call register and then select

•

Missed calls to view up to 20 phone numbers from which somebody has tried

to call you (network service). The number in front of the (name or) phone

number indicates the number of call attempts from that caller.

Tip: When a note about missed calls is displayed, press List to access the

list of phone numbers. Scroll to the number you would like to call back

and press

•

Received calls to view up to 20 phone numbers from which you have most

recently accepted calls (network service).

Dialled numbers to view up to 20 phone numbers that you have most recently

called or attempted to call. See also Last number redialling on page 47.

Delete recent call lists to delete the recent calls lists. Select whether you want

to delete all the phone numbers in the recent calls lists, or only the numbers in

the missed calls, received calls or dialled numbers lists. You cannot undo the

operation.

Timers and counters

Note: The actual invoice for calls and services from your service provider may vary,

depending upon network features, rounding-off for billing, taxes and so forth.

Press Menu, select Call register and Timers and counters. Select

•

Call duration. Scroll to view the approximate duration of your incoming and

outgoing calls in hours, minutes and seconds. The security code is required to

clear the timers.

If you have two phone lines available (network service), each phone line has its

own call duration timers. The timers of the selected line are displayed. See Call

settings on page 126.

•

GPRS data counter. Scroll to check the amount of data that were sent or

received in bytes, sent and received data in total, and to clear the counters. The

security code is required to clear the counters.

GPRS connection timer. Scroll to check the approximate duration of the last

GPRS connection or the total GPRS connection time. You can also clear the

timers. The security code is required to clear the timers.

■ Contacts (Menu 3)

You can save names and phone numbers (contacts) in both the

phone’s memory and in the SIM card’s memory.

• You may save up to 500 names with numbers and text notes for each name in

the phone’s memory. You can also save an image for a certain number of

names. The number of names that can be saved depends on both the length of

the names, and the number and length of the phone numbers and text items.

Contacts use shared memory, see Shared memory on page 23.

• The phone supports SIM cards that can save up to 250 names and phone

numbers. Names and numbers that are saved in the SIM card’s memory, are

indicated by

In dynamic contacts (Presence) you can publish your current availability status to

people with compatible devices who have access to this service and who are

requesting this information. You can view the availability status of the contacts

that you have subscribed to in the Subscribed names menu and in the detailed

view of a name in Contacts.

Selecting settings for contacts

Press Menu and select Contacts and Settings. Select

•

Memory in use to select the memory, either SIM card or phone, that you want

to use for your contacts. To recall names and numbers from both memories for

contacts, select Phone and SIM. In this case, the names and numbers will be

saved in the phone’s memory.

•

Contacts view to select how the names, numbers and images in contacts are

displayed.

Memory status to view how much free memory is available for contacts in both

the SIM card and phone.

Saving names and phone numbers (Add contact)

Names and numbers will be saved in the memory in use, see Selecting settings for

contacts above.

100

1. Press Menu and select Contacts and Add contact.

2. Key in the name and press OK. See Using traditional text input on page 54.

3. Key in the phone number, and press OK. To key in numbers, see Making a call

on page 46.

4. When the name and number have been saved, press Done.

Tip: Quick save: In standby mode, key in the phone number and press Save.

Key in the name, press OK and Done.

Saving multiple numbers and text items per name

You can save different types of phone numbers and short text items for each name

in the phone’s internal memory for contacts.

The first number saved is automatically set as the default number and it is

indicated by a frame around the number type indicator, for example

. When

you select a name from Contacts, for example to make a call, the default number

is used unless you select another number.

1. Make sure that the memory in use is either Phone or Phone and SIM. See

Selecting settings for contacts on page 100.

2. To access the list of names and phone numbers, move the joystick down in

standby mode.

3. Scroll to the name saved in the phone’s internal memory for the contact to

which you want to add a new number or text item, and press Details.

4. Press Options and select Add number or Add detail.

101

5. To add a number or detail, select one of the number types or text types,

respectively.

• If you select the text type User ID:

Select Search to search for an ID by a mobile phone number or an e-mail

address in the server of the operator or service provider if you have

connected to the presence service. See My presence on page 105. If only

one ID is found, it is automatically saved. Otherwise, to save the ID, press

Options, and select Save.

To key in the ID, select Enter ID manually. Key in the ID and press OK to save

it.

To change the number or text type, select Change type in the options list. Note

that you cannot change the type of an ID when it is on the Chat contacts or in

the Subscribed names list.

To set the selected number as the default number, select Set as default.

6. Key in the number or text item and press OK to save it.

7. Press Back and then Exit to return to standby mode.

Adding an image to a name or number in contacts

You can add an image in supported format to a name or number saved in the

phone’s internal memory.

Move the joystick down in standby mode, scroll to the name (and number) and

press Details. Press Options and select Add image. The phone opens the list of

102

folders in the Gallery. Scroll to the desired image, press Options and select Save to

contacts.

Searching for a contact

1. Press Menu and select Contacts and Search or move the joystick down in

standby mode.

2. You can key in the first characters of the name that you are searching for in the

pop-up window.

Move the joystick up or down to scroll through the names in the list, and right

or left to move the cursor in the pop-up window.

3. Scroll to the contact that you want, and press Details. Scroll to view the details

of the selected contact.

Depending on the Contacts view selection in Selecting settings for contacts on

page 100, the subscribed contacts are shown differently. Either only the

availability indicator or the availability indicator, personal logo and the status

message are shown. Press Details to view all dynamic information.

Tip: To quickly view a specific name with the default number, when the flip

is closed, press and hold

at the name while scrolling through

Contacts.

To view the status message in full, press Details and press and hold

at the

dynamic contact while scrolling through the contact names.

103

Deleting contacts

Press Menu, select Contacts and Delete to delete a contact and all the details

attached to it.

If the contact has an ID on the Chat contacts or in the Subscribed names list, the

note Presence information will be deleted is shown before the contact is deleted.

• To delete names and numbers one by one, select One by one and scroll to the

name (and number) that you want to delete. Press Delete and press Yes.

• To delete contacts all at once, select Delete all and then scroll to either of the

memories, Phone or SIM card, and press Delete. Press Yes and confirm with the

security code.

Editing or deleting details in contacts

Move the joystick down in standby mode, scroll to the contact that you want to

edit or delete and press Details. Scroll to the name, number, text item or image

that you want to edit or delete.

• Press either Edit or Change, or press Options and select Edit name, Edit

number, Edit detail or Change image depending on the Contacts view selection

in Selecting settings for contacts on page 100.

Note that you cannot edit or delete an ID when it is on the Chat contacts or in

the Subscribed names list.

• To delete a number or text item, select Delete number or Delete detail.

• To delete an image that is attached to the contact, select Delete image.

Deleting an image from Contacts does not delete it from the Gallery.

104

My presence

With the presence service (network service), you can share your presence status

with other users of the service. The presence status includes your availability,

status message and personal logo. Other users who have access to the service and

who request your information are able to see your status. The requested

information is shown in Subscribed names in the viewer’s Contacts menu. You can

personalise the information that you want to share with others and control who

can see your status.

Before you can use presence, you need to subscribe to the service. To check the

availability and pricing, and to subscribe to the service, contact your network

operator or service provider, from whom you also receive your unique ID and

password and the settings for the service. To set the required settings for the

presence service, see Chat and my presence settings on page 115. While you are

connected to the presence service, you can use the other functions of the phone,

and the presence service is active in the background.

Press Menu and select Contacts and My presence. Select

•

Connect to ’My presence’ service (or Disconnect) to connect to or disconnect

from the service.

•

My current presence to change your presence status. Select

•

View current presence and select Private pres. or Public pres. to view your

current private or public status.

•

My availability to set your availability status to Available indicated by

or to Busy indicated by , or to Not available indicated by

105

•

My presence message and key in the text to be shown to others or press

Options and select Previous msgs. and select an old message as the status

message.

•

My presence logo to select your personal logo from the Graphics folder in

the gallery. If you select the default, the logo is not published.

Show to to select the groups to whom you want to show or not to show

your presence status.

Select Private and public and contacts in your private list are able to see all

your presence information: availability, status message and logo. Other

contacts can see only your availability.

Select Private viewers and the contacts in your private list can see all your

presence information (availability, status message and logo). Other users

will not see any information.

If you select No one, no one can see your presence information.

•

Viewers and select

•

Current viewers to view all the persons who have subscribed to your

presence information.

•

Private list is a list of the persons who are allowed to view all your presence

information, including availability, status message and logo. You can

manage your own private list. Other persons who are not in the private list,

can see only your availability.

•

Blocked list to view all the persons you have blocked from viewing your

presence information.

106

•

Settings and select

•

Show current presence in idle to show the current status indicator in

standby mode.

•

Synchronise with profiles to select whether you want to link My presence

message and My availability manually or automatically to the currently

active profile. Note that you cannot link a personalised status logo to a

Profile. See also Profiles on page 114.

•

Connection type to set the phone to automatically connect to the service

when the phone is switched on.

Connect. settings see Chat and my presence settings on page 115.

Subscribed contacts

You can create a list for contacts whose presence status you wish to be aware of

(network service). You can view the information if allowed by the contacts and if

it is not prevented by the network. You can view the subscribed contacts either by

scrolling through the contacts or via the Subscribed names menu.

Make sure that the memory in use is either Phone or Phone and SIM. See Selecting

settings for contacts on page 100.

To connect to the Presence service, press Menu and select Contacts, My presence

and Connect to ’My presence’ service. You can also view the subscribed contacts

when you are not connected to the presence service, but you cannot see the

presence status of the contact.

107

Adding contacts to the subscribed contacts

1. Press Menu and select Contacts and Subscribed names. If you have not

connected to the Presence service, the phone asks if you want to connect now.

2. If you have no contacts on your list, press Add. Otherwise, press Options and

select Subscribe new. The list of contacts is shown.

3. Select a contact from the list and if the contact has an ID saved, the contact is

added to the subscribed contacts list. If there is more than one ID, select one of

them. After subscription to the contact, Subscription activated is shown.

Tip: To subscribe to a contact from the Contacts list, move the joystick

down in standby mode and scroll to the contact that you want to subscribe

to. Press Details and press Options. To subscribe, select Request presence

and select As subscription.

If you only want to view the presence information without subscribing to a

contact, select Request presence and One time only.

Viewing the subscribed contacts

See also Searching for a contact on page 103 to view the presence information.

1. Press Menu and select Contacts and Subscribed names.

The status information of the first contact on the dynamic contacts list is

shown and it may include text and some of the following icons:

indicate that the person is either available, busy or not available.

indicates that the person’s presence information is not available.

108

2. Scroll to the desired contact and press Details to view the details of the

selected contact. If you press Options, you can select

•

Subscribe new to add a new contact to the list of subscribed contacts.

Chat to start a chat conversation.

Send message to send a text message to the selected contact.

Send SMS e-mail to send an e-mail to the selected contact.

Send bus. card to send a business card of the selected contact.

Unsubscribe to remove the selected contact from the list of subscribed

contacts.

Unsubscribing a contact

• To unsubscribe a contact from the Contacts list, move the joystick down in

standby mode and scroll to the contact that you want to unsubscribe. Press

Details and select the ID and press Options. To unsubscribe, select Unsubscribe

and press OK to confirm.

• To unsubscribe via the Subscribed names menu, see Viewing the subscribed

contacts on page 108.

Copying contacts

You can copy names and phone numbers from the phone’s memory to your SIM

card’s memory and vice versa. Note that any text items saved in the phone’s

internal memory, such as e-mail addresses, will not be copied to the SIM card.

1. Press Menu and select Contacts and Copy.

109

2. Select the copying direction, From phone to SIM card or From SIM card to

phone.

3. Select One by one, All or Default numbers.

Default numbers is shown if you copy from the phone to the SIM card. Only the

default numbers will be copied.

4. To choose whether you want to keep or delete the original names and numbers,

select Keep original or Move original.

Sending and receiving a business card

You can send and receive a person’s contact information as a business card from a

compatible device.

When you have received a business card, press Show and Save to save the

business card in the phone’s memory. To discard the business card, press Exit and

then OK.

To send a business card, search for the name and phone number that you want to

send in Contacts, press Details and Options and select Send bus. card. Select Via

infrared, Via text message (network service), or Via Bluetooth.

Speed dials

To assign a number to a speed-dialling key, press Menu and select Contacts,

Speed dials and scroll to the desired speed-dialling key number.

Press Assign, or if a number has already been assigned to the key, press Options

and select Change. Press Search, and select first the name and then the number

110

you want to assign. If the Speed dialling function is off, the phone asks whether

you want to activate it.

To make a call using the speed-dialling keys, see Speed dialling a phone number

on page 47.

Voice dialling

You can make a phone call by saying a voice tag that has been added to a phone

number. Any spoken word(s), such as a person’s name(s), can be a voice tag. You

can add up to ten voice tags.

Before using voice dialling, note that:

•

Voice tags are not language dependent. They are dependent on the speaker's voice.

Voice tags are sensitive to background noise. Record them and make calls in a quiet

environment.

•

When recording a voice tag or making a call by saying a voice tag, hold the phone in the

normal position near to your ear.

Very short names are not accepted. Use long names and avoid similar names for different

numbers.

Note: You must say the name exactly as you said it when you recorded it. This may

be difficult in, for example, a noisy environment or during an emergency, so you

should not rely solely upon voice dialling in all circumstances.

Adding and managing voice tags

• Save or copy the contacts to which you want to add a voice tag into the

phone’s memory. You can also add voice tags to the names in the SIM card, but

111

if you replace your SIM card with a new one, you first need to delete the old

voice tags before you can add new ones. Voice tags use shared memory, see

Shared memory on page 23.

1. In standby mode, press Menu, and select Contacts and Search, scroll to the

desired contact and press Details.

2. Press Options and select Add voice tag.

3. Press Start, and say clearly the word(s) you want to record as a voice tag. After

recording, the phone plays the recorded tag.

4. When the voice tag has been successfully saved, Voice tag saved is displayed, a

beep sounds and a symbol

appears after the phone number with a voice

tag.

To check the voice tags, press Menu and select Contacts and Voice tags. Scroll to

the contact you require, select it and the function you require.

Making a call by using a voice tag

If the phone is using an application involving a GPRS connection which is sending

or receiving data, end the application in order to make a call using voice dialling.

1. In standby mode, press and hold

, or press and hold the volume down key at

the side of the phone. A short tone is heard and Speak now is displayed.

2. Say the voice tag clearly. The phone plays the recognised voice tag and then

dials the phone number of the voice tag after 1.5 seconds.

If you are using a compatible headset, press and hold the headset key to start the

voice dialling.

112

Info numbers and service numbers

Your service provider may have included information numbers or service numbers

on your SIM card.

Press Menu and select Contacts and Info numbers or Service numbers. Scroll

through a category to an information number, or to a service number and press

to call the number.

My numbers

The phone numbers assigned to your SIM card are saved in My numbers if this is

allowed by the card. To view the numbers press Menu and select Contacts and My

numbers. Scroll to the desired name or number, and press View.

Caller groups

You can arrange the names and phone numbers saved in Contacts into caller

groups. For each caller group, you can select a ringing tone and you can turn on or

off a logo that is shown on the display when you receive a call from a phone

number in the group. To set the phone to ring only upon calls from an identified

phone number that belongs to a selected caller group, see Alert for in Tone

settings on page 116.

Press Menu and select Contacts, Caller groups and select the desired caller group.

You can select from the following functions Group name, Group ringing tone,

Group logo, Group members.

113

If you select Group members, press Add to add a name to the group. Scroll to the

name that you want and press Add.

To remove a name from a caller group, scroll to the desired name, and press

Remove.

■ Settings (Menu 4)

Profiles

Your phone has a group of profiles that allow you to personalise the tone settings

of your phone and to activate a profile for different events and environments.

Available profiles are General, Silent, Meeting, Outdoor, My style 1 and My style 2.

Press Menu and select Settings and Profiles. Scroll to a profile and press Select.

• To activate the selected profile, select Activate.

• To activate the profile for a certain amount of time (up to 24 hours), select

Timed and set the end time. When the timed profile expires, the previous

profile that was not timed becomes active.

• To personalise the profile, select Personalise. Select the setting that you want

to change and make the changes.

The settings can also be changed in the Tone settings menu, see Tone settings

on page 116.

To rename a profile, select Profile name. The General profile cannot be

renamed.

114

• To change your presence status, select My presence. The menu is available if

you have set Synchronise with profiles to On, see My presence on page 105.

Select My availability to change your availability status and My presence

message to edit your status message.

Tip: To quickly change the profile in standby mode, press the power key

, scroll to the profile that you want to activate and press Select.

Chat and my presence settings

For the settings required for chat, contact your network operator or service

provider. To receive the chat and presence settings over the air, see Over-the-air

settings service on page 44.

Keying in the settings manually

1. Press Menu, and select Settings, Chat and my presence settings and Current

chat and presence settings.

2. Scroll to the set you would like to activate and press Activate.

You need to activate the connection set where you want to save the settings. A

connection set is a collection of settings required to make a connection to the

chat and presence services.

3. Select Edit current chat and presence sett..

Select each of the settings one by one and key in all the required information

that you have received from your network operator or service provider. Note

that the connection settings are in the Connection settings menu.

115

Tone settings

You will find the same settings in the Profiles menu, see Profiles on page 114. Note

that the settings you make will change the settings in the active profile.

Press Menu and select Settings and Tone settings. Select

•

Incoming call alert and select how the phone notifies you of an incoming voice

call.

•

Ringing tone to select a tone for incoming voice calls. To select ringing tones

that have been saved in the Gallery, select Open gallery from the ringing tone

list.

•

Ringing volume to set the tone level for incoming voice calls and incoming

messages.

Tip: If you download a ringing tone or receive one via OTA, you can save

it in the Gallery.

Vibrating alert to set the phone to vibrate for incoming voice calls and

incoming messages. The vibrating alert does not work when the phone is

connected to a charger, a desktop stand, or a car kit.

•

Message alert tone to set the alert tone for incoming messages.

Chat alert tone to set the alert tone for incoming instant messages.

Keypad tones to adjust the tone level of the keypad.

Warning tones to set the phone to sound tones, for example when the battery

is running out of power.

116

•

Alert for to set the phone to ring only on calls from phone numbers that belong

to a selected caller group. Scroll to the caller group that you want or All calls

and press Mark.

Display settings

Press Menu and select Settings, Display settings. Select

•

Wallpaper to set the phone to display a background image, known as

wallpaper, when the phone is in standby mode. Some images are pre-saved in

the Gallery menu. You can also receive images, for example via multimedia

messages, or use PC Suite to transfer them from a compatible PC and then save

them in the Gallery. Your phone supports JPEG, GIF, WBMP, BMP, OTA-BMP

and PNG formats, but not necessarily all variations of these formats.

• Select Select wallpaper and open an image folder. Scroll to the desired

image you want to set as wallpaper, press Options and select Set as

wallpaper.

• To activate/deactivate the wallpaper, select On or Off.

Note that the wallpaper is not displayed when the phone activates the

screen saver.

•

Colour schemes to change the colour of some display components, for example

indicators and signal bars.

Menu view to select how the main menu items are displayed on the phone.

Select List or Grid.

117

•

Operator logo to set the phone to show or hide the operator logo. If you have

not saved any operator logos, the Operator logo menu is dimmed.

The operator logo is not displayed when the phone activates the screen saver.

Screen saver time-out and select the timeout after which the screen saver will

be activated. The length of the timeout can vary from 5 seconds to 60 minutes.

The digital clock screen saver is used for power saving. It is activated when no

phone function has been used for a set length of time. Press any key to

deactivate the screen saver. The screen saver is also deactivated when the

phone is out of the network coverage area. The screen saver overrides graphics

and texts on the display in standby mode.

•

Display contrast to change the brightness level of the phone display. Move the

joystick to the left to decrease and to the right to increase the brightness level,

and press OK to accept it.

Time and date settings

Press Menu and select Settings, Time and date settings. Select

•

Clock and select Show clock (or Hide clock ) to show (or hide) the time on the

top right of the display in standby mode. Select Set the time to adjust the clock

to the correct time, and Time format to select the 12-hour or 24-hour time

format.

The clock is also used for the functions Messages, Call register, Alarm clock,

timed Profiles, Calendar, Notes, and screen saver, for example.

118

If the battery is removed from the phone for a long time, you may need to reset

the time.

•

Date and select Show date (or Hide date) to show (or hide) the date on the

display in standby mode. Select Set the date to adjust the date. You can also

select the date format and the date separator.

Auto-update of date & time (network service) to set the phone to

automatically update the time and date according to the current time zone,

select On. To set the phone to ask for confirmation before the update, select

Confirm first.

The automatic update of date and time does not change the time you have set

for the alarm clock, calendar or the alarm notes. They are in local time.

Updating may cause some alarms that you have set to expire.

Personal shortcuts

You can select the function for the right selection key displayed in standby mode.

You also have a list of phone functions that can be activated by saying a voice tag.

Up to five voice tags for the voice commands can be added.

Press Menu, and select Settings and Personal shortcuts. Select

•

Right selection key to view the list of available functions for the right selection

key. Scroll to the function that you want and select it.

•

Voice commands and select the voice command folder that you want, scroll to

the function to which you want to add a voice tag and press Add. If the

119

command already has a voice tag, the indicator

is shown. For adding and

activating a voice command, see Voice dialling on page 111.

During a call or when an application using the EGPRS connection is sending or

receiving data, you cannot activate or add a voice command.

Connectivity

You can connect the phone to a compatible device via infrared or Bluetooth

connection. You can also define the settings for EGPRS dial-up connections. Note

that the Bluetooth and infrared connections cannot be active at the same time.

Bluetooth wireless technology

The phone supports Bluetooth wireless technology which allows you to connect

the phone to a compatible device within 10 metres. The Bluetooth connection can

be subject to interference from obstructions such as walls or other electronic

devices.

This phone is compliant with Bluetooth Specification 1.1 which supports the

following Bluetooth profiles: Serial Port Profile, Dial-up Networking Profile,

Object Push Profile, File Transfer Profile and Headset Profile. Handsfree Profile is

supported by Specification 1.0 and SIM Access Profile by version 0.95.

To ensure interoperability between Bluetooth devices, use Nokia-approved

accessories for this model. Check with the manufacturers of other Bluetooth

devices to determine their compatibility with this phone. In some countries, there

may be restrictions on using Bluetooth devices. Check with your local authorities.

120

The SIM Access Profile allows you to connect to compatible devices, such as the

Nokia car enhancement RAN 610. When the SIM Access Profile is active, the

phone is disconnected from the GSM network, and thus, all phone functions are

deactivated.

Note: Using Bluetooth consumes the battery and the phone's operating time will

be reduced. Be careful not to let it run in the background when performing other

operations with your phone.

Setting up a Bluetooth connection

1. Press Menu, and select Settings, Connectivity and Bluetooth.

2. To activate the Bluetooth function, select Bluetooth and On. The active

Bluetooth connection is indicated by

at the top of the display.

If you do not use the Bluetooth feature for some time, you can deactivate it to

save power.

3. Select Search for audio enhancements to search for compatible Bluetooth

devices and select the device that you want to connect to the phone.

4. Enter the Bluetooth passcode of the device to associate (’pair’) and connect the

device to your phone and start using the device.

You only need to give this passcode when you connect to the device for the

first time.

Bluetooth connection

Press Menu, and select Settings, Connectivity and Bluetooth. Select

•

Active device to check which Bluetooth connection is currently active. If you

want to close the connection to the selected device, press Disconnect.

121

•

Paired devices to view a list of Bluetooth devices that are currently paired with

the phone. Scroll to the desired device. If you want to delete the pairing, press

Delete.

Press Options to access some of the following functions depending on the status

of the device and the Bluetooth connection. Select

•

Connect to connect to the selected device.

Assign short name to give a nickname (only visible to you) to the selected

device.

•

Auto-conn. without confirmation and select No if you want the phone to

automatically connect to the selected device, or select Yes if you want the

phone to ask for your permission first.

Bluetooth settings

Press Menu, and select Settings, Connectivity, Bluetooth and Bluetooth settings

to define how your phone is shown to other Bluetooth devices. Select

•

My phone's visibility and Shown to all to show the phone to all other Bluetooth

devices or Hidden to show the phone only to the paired devices.

•

My phone's name to change your phone’s Bluetooth device name that can be

seen by other Bluetooth device users.

Infrared

The phone has an infrared port that you can use for connecting your phone to

another IrDA compliant device. You can send or receive data such as business

cards and calendar notes to or from a compatible phone or data device (for

example a computer).

122

Do not point the IR (infrared) beam at anyone's eye or allow it to interfere with other IR

devices. This device is a Class 1 Laser product.

Sending and receiving data via IR

• Ensure that the IR ports of the sending and receiving devices are pointing at

each other and that there are no obstructions between them. The preferable

distance between the two devices in an infrared connection should be one

metre at most.

• To activate the IR port of your phone to receive data via IR, press Menu and

select Settings, Connectivity and Infrared.

• The user of the sending phone selects the desired IR function to start data

transfer.

If the data transfer is not started within two minutes of the activation of the IR

port, the connection is cancelled and has to be started again.

IR connection indicator

• When

your phone is ready to send or receive data via its IR port.

• When blinks, your phone is trying to connect to the other device or a

connection has been lost.

is shown continuously, the IR connection has been activated and

Note that the IR connection deactivates automatically.

EGPRS

GPRS (General Packet Radio Service) is a network service that allows mobile

phones to be used for sending and receiving data over an Internet Protocol (IP)-

based network.

123

EGPRS (Enhanced GPRS), also known as EDGE (Enhanced Data Rates for Global

Evolution) is similar to GPRS but it enables faster connection. For more

information on the availability of EGPRS and data transfer speed, contact your

network operator or service provider.

The applications that may use EGPRS are multimedia, chat and text messaging,

browsing sessions, e-mail, remote OMA Data Syncronization, Java application

downloading and the PC dial-up (for example, Internet and e-mail).

Before you can use EGPRS technology:

• Contact your network operator or service provider for availability and

subscription to the EGPRS service.

• Save the EGPRS settings for each of the applications used over EGPRS.

For information on pricing, contact your network operator or service provider.

Note that when you have selected GPRS as a data bearer, the phone uses EGPRS

instead of GPRS if this is available in the network. You cannot choose between

EGPRS and GPRS but for some applications you may be able to select either GPRS

or GSM data (CSD, Circuit Switched Data).

EGPRS connection

Press Menu and select Settings, Connectivity, GPRS and GPRS connection.

• Select Always online to set the phone to automatically register to an EGPRS

network when you switch the phone on. When the GPRS connection is

established, the indicator is shown on the top left of the display.

When you start an application using EGPRS, the connection between the

phone and the network is established, and data transfer is possible. When you

124

end the application, the EGPRS connection is ended but the registration with

the EGPRS network remains.

If you receive a call or a text message, or make a call during a GPRS

connection, the indicator

will be shown on the top right of the display to

indicate that the EGPRS connection has been suspended (put on hold).

The GPRS and EGPRS connections are indicated by the same indicators.

• If you select When needed, the EGPRS registration and connection are

established when required by an application using GPRS and closed when you

end the application.

Note that your phone supports three simultaneous EGPRS connections. For

example, depending on the network, you can simultaneously browse xHTML

pages, receive multimedia messages and have an ongoing PC dial-up connection.

EGPRS modem settings

You can connect the phone to a compatible PC via infrared, Bluetooth wireless

technology or a data cable connection and use the phone as a modem to enable

EGPRS connectivity from the PC.

Press Menu and select Settings, Connectivity, GPRS and GPRS modem settings.

Select Active access point to activate the desired access point. Select Edit active

access point to change the access point settings.

• Scroll to Alias for access point and press Select. Key in the name that you

would like for the activated access point and press OK.

125

• Scroll to GPRS access point and press Select. Key in the Access Point Name

(APN) to establish a connection to an EGPRS network. Contact your network

operator for the APN.

You can also set the EGPRS dial-up service settings (Access Point Name) on your

PC using the Nokia Modem Options software, see PC Suite on page 172. If you

have set the settings on both your PC and on your phone, note that the PC’s

settings will be used.

More settings

Call settings

Press Menu and select Settings, More settings and Call settings. Select

•

Call divert (network service) to direct your incoming calls, for example to your

voice mailbox number. Divert options that are not supported by your SIM card

or your network operator may not be shown. Contact your service provider for

details.

For example, select Divert if busy to divert your voice calls when your number is

busy or when you reject an incoming call.

To set the divert setting to on, select Activate and then select the timeout after

which the call is diverted, if this is available for the call divert option. To set the

call divert option to off, select Cancel. To check whether the call divert is

activated or not, select Check status if this is available for the divert option.

Several divert options may be active at the same time.

126

To see the divert indicators in standby mode, see Essential indicators in

standby mode on page 40.

•

Anykey answer and select On and you can answer an incoming call by briefly

pressing any key, except

, selection keys

and

when the flip is

closed ( and when the flip is open), and

•

Automatic redial and select On and your phone will make a maximum of ten

attempts to connect a call after an unsuccessful call attempt.

Speed dialling and select On and the names and phone numbers that are

assigned to the speed-dialling keys, from

with the flip closed,

or the corresponding number keys of the keyboard, can be dialled by pressing

and holding the corresponding number key.

•

Call waiting and select Activate and the network will notify you of an incoming

call while you have a call in progress (network service). See Call waiting on

page 48.

•

Summary after call and select On and after each call the phone will briefly

display the approximate duration of the call.

Send my caller ID and select Yes and your phone number will be displayed to

the person you are calling (network service). Select Set by network and the

setting agreed upon with your service provider is used.

•

Line for outgoing calls (network service) to select the phone line 1 or 2 for

making calls, for example you can use line 1 for personal calls and line 2 for

business calls. For more information on availability, contact your network

operator or service provider.

127

If you select Line 2 and have not subscribed to this network service, you will

not be able to make calls. However, calls on both lines can be answered

regardless of the selected line.

If supported by your SIM card, you can prevent the line selection by selecting

the Lock option.

Phone settings

Press Menu and select Settings, More settings, Phone settings. Select

•

Phone language to set the language for the display texts. If Automatic is

selected, the phone selects the language according to the information on the

SIM card.

•

Memory status to view the amount of free, used and total amount of memory

for each function. You may also find memory information in the menus of

some functions, for example in the Applications menu.

• Select Automatic keyguard to set the keypad of your phone to lock

automatically after a pre-set time delay when the phone is in standby mode

and no function of the phone has been used. Select On and you can set the

time from 5 seconds to 60 minutes.

See also Keypad lock (Keyguard) on page 43.

•

Security keyguard to lock the keypad of the phone with a security code, see

Security code (5 to 10 digits) on page 20.

• Enter the security code. To set the security keyguard, select On.

The keypad lock remains active, if you open the flip.

128

To activate the security keyguard, press Menu and

within 1.5

seconds, when the flip is closed. To deactivate the keyguard when the flip is

open, press Unlock and OK, then key in the security code. If the flip is

closed, press Unlock and

within 1.5 seconds, then key in the security

code.

When the keypad is locked,

appears on top of the display. Note that if

you have activated the security keyguard, it does not protect your phone

data from PC Suite access.

•

Cell info display and select On to set the phone to indicate when it is used in a

cellular network that is based on Micro Cellular Network (MCN) technology

(network service).

•

Welcome note and key in the note that you would like to be shown briefly

when the phone is switched on. To save the note, press Save.

Operator selection and Automatic and the phone automatically selects one of

the cellular network operators available in your area.

If you select Manual, you can select a network operator that has a roaming

agreement with your home network operator. If No network access is

displayed, you must select another network operator. The phone stays in

manual mode until the automatic mode is selected or another SIM card is

inserted into the phone.

•

Confirm SIM service actions. See SIM services (Menu 10) on page 170.

Help text activation to set the phone to show the help texts. See also Using the

menu on page 57.

129

•

Start-up tone to set the phone to play a start-up tone when it is switched on.

Enhancement settings

The enhancement settings menu is only shown if the phone is or has been

connected to mobile enhancements, for example to handsfree units.

Press Menu and select Settings, More settings and Enhancement settings. Then

select an appropriate enhancement from a list, if the corresponding enhancement

is or has been connected to the phone. Select

•

Default profile to automatically activate the desired profile when you connect

to the selected enhancement. You can select another profile while the

enhancement is connected.

Automatic answer to set the phone to automatically answer an incoming call

after five seconds. If the Incoming call alert is set to Beep once or Off,

automatic answer will not be used.

Lights to set the lights permanently to On. Select Automatic to set the lights

on for 15 seconds after a keypress. The Lights option is available only when

Handsfree is selected.

• When the phone is connected to the full car kit, select Ignition detector and On

to automatically switch off the phone approximately 20 seconds after you

have switched off the car’s ignition.

• For Text phone, select Use text phone and select Yes to use the text phone

settings instead of the headset or loopset settings.

130

Security settings

Note: When security features that restrict calls are in use (call barring, closed user

group and fixed dialling), calls may be possible to certain emergency numbers in

some networks (e.g. 112 or other official emergency numbers).

Press Menu and select Settings, More settings and Security settings.

Select

•

PIN code request to set the phone to ask for your PIN code every time the

phone is switched on. Some SIM cards do not allow the PIN code request to be

turned off.

•

Call barring service (network service) to restrict incoming calls to and outgoing

calls from your phone. A barring password is required.

Fixed dialling to restrict your outgoing calls and text messages to selected

phone numbers if this function is supported by your SIM card. The PIN2 code is

required.

When the fixed dialling setting is on, GPRS connections are not possible except

while sending text messages over a GPRS connection. In this case, the

recipient’s phone number and the message centre number must be included in

the fixed dialling list.

•

Closed user group. Closed user group is a network service that specifies the

group of people whom you can call and who can call you. For more

information, contact your network operator or service provider.

Security level. Select Phone and the phone will ask for the security code

whenever a new SIM card is inserted into the phone.

131

Select Memory to set the phone to request the security code when the SIM

card’s memory is selected and you want to change the memory in use, see

Selecting settings for contacts on page 100, or copy from one memory to

another, see Copying contacts on page 109.

•

Access codes to change the security code, PIN code, PIN2 code or barring

password. Codes can only include numbers from 0 to 9.

Restore factory settings

To reset the menu settings to their original values, press Menu and select Settings

and Restore factory settings. Key in the security code and press OK. Note that the

data you have keyed in or downloaded, for example the names and phone

numbers saved in Contacts, are not deleted.

■ Gallery (Menu 5)

Note: Your phone must be switched on to use this function.

Do not switch the phone on when wireless phone use is prohibited or when it may

cause interference or danger.

In the Gallery menu you can manage images, photos, recordings, tones and video

clips that you have, for example, received in multimedia messages, see Reading

and replying to a multimedia message on page 73.

Your phone supports a usage rights system to protect acquired content. A piece of

content, for example a ringing tone, can be protected and associated with certain

usage rules, for example a number of usage times and a certain usage period. The

132

rules are defined in the content’s usage rights, which can be delivered either

together with the content or independently depending on the service provider.

You may be able to update these rights. Always check the delivery terms of any

content and usage rights before acquiring them, as they may be subject to a fee.

The gallery uses shared memory, see Shared memory on page 23.

1. Press Menu and select Gallery. A list of folders is shown. Video clips, Graphics,

Tones and Recordings are the original folders on the phone.

2. Scroll to the desired folder and press Open to view a list of files in the folder or

press Options and one of the following options may be available:

•

Delete folder, Move, Rename folder, Details, Type of view, Sort, Add folder,

Activation key list and Downloads

You cannot delete, rename or move the original folders on the phone.

Type of view to select how the folders are displayed.

•

Activation key list to view the list of available usage rights.

Downloads to download more images and tones. Select Graphic downloads

or Tone downloads. The list of available browser bookmarks is shown. Select

More bookmarks to access the list of bookmarks in the Services menu, see

Bookmarks on page 165.

Select the appropriate bookmark to connect to the desired site. If the

connection fails, you may not be able to access the page with the currently

activated service settings. In this case, enter the Services menu and activate

another set of service settings, see Connecting to a service on page 160. Try

again to connect to the site.

133

For the availability of different services, pricing and tariffs, contact your

network operator and/or the service provider. Download content only from

sources you trust.

3. If you opened a folder in step 2, select the file you want to view and press

Open.

Or: Press Options and use one of the following functions that may be available

for the selected file (functions such as Rename are not available for read-only

files):

•

Delete, Send, Move, Rename, Set as wallpaper, Set as ring tone, Edit image,

Details, Type of view, Sort, Delete all, Open in sequence, Play, Mute audio

(Unmute audio), Set contrast.

•

Send to send the selected file via MMS, Bluetooth or IR connection.

Delete all to delete all the files in the selected folder.

Edit image to insert text, a frame or clip-art into the selected picture.

Open in sequence to view the files in the folder one by one.

Play to listen to or to view a sound or image file that is contained in the

message.

•

Mute audio (Unmute audio) to mute (unmute) the sound of a video file.

Set contrast to adjust the contrast level of the image.

Activate content to update the usage rights of the selected file. This option

is only shown if the rights update is supported by the file.

134

from being copied, modified, transferred or forwarded.

■ Radio (Menu 6)

Note: Your phone must be switched on to use this function. Do

not switch the phone on when wireless phone use is prohibited or when it may

cause interference or danger.

To listen to the radio on your phone, connect the compatible headset to the

headset connector on the bottom of the phone. The lead of the headset functions

as the radio antenna, so let it hang freely.

Note that the quality of the radio broadcast depends on the radio station’s

coverage in that particular area.

1. To turn on the radio, press Menu and select Radio. The following are shown on

the display:

• The channel location number and the name of the radio channel, if you

have previously saved it.

• The frequency of the radio channel.

2. If you have pre-saved radio channels, you can scroll to the channel that you

would like to listen to, or select a radio channel location from 1 to 9 by

pressing the corresponding number key.

When using the compatible headset, press the headset key to scroll to the

desired radio channel that you have saved.

135

3. When the radio is on, press Options and select Switch off to turn off the radio.

Tip: To return to standby mode, press briefly; to quickly turn off the

radio, press and hold

Tuning a radio channel

When the radio is on, move the joystick up or down to start the channel search.

Searching stops when a channel has been found. To save the channel, press

Options and select Save channel. Key in the name of the channel and press OK.

Select the location to which you want to save the channel.

Tip: To quickly save the channel in locations 1 to 9, press and hold the

corresponding number key, then key in the name of the channel and press

OK.

Using the radio

When the radio is on, press Options and select

•

Switch off to turn off the radio.

Save channel to save the radio channel that you have found, refer to Tuning a

radio channel above. Up to 20 radio channels can be saved.

•

Automatic tuning. Move the joystick up or down to start searching upwards or

downwards for channels. The search stops when a channel has been found,

press OK. To save the channel, see Save channel above.

Manual tuning. Move the joystick up or down to start searching upwards or

downwards for channels, or hold the joystick in the up or down position to

136

search for channels more quickly. To save the channel, press OK and see Save

channel above.

Tip: To quickly select Manual tuning, press

when in the Radio

menu.

•

Set frequency. If you know the frequency of the radio channel to which you

would like to listen (between 87.5 MHz and 108.0 MHz), key it in and press OK.

To save the channel, see the Save channel option.

Tip: To quickly select Set frequency, press

when in the Radio

menu.

Delete channel. To delete a saved channel, scroll to the desired channel, select

Delete and OK.

•

Rename. Key in a new name for the saved channel and press OK.

Loudspeaker (or Headset) to listen to the radio through a loudspeaker (or

headset). Keep the headset connected to the phone because the lead of the

headset functions as the radio antenna. Note that if you receive an incoming

call, it is always routed to the headset.

•

Mono output (or Stereo output) to listen to the radio in mono (or in stereo).

When you make a call or answer an incoming call while listening to the radio, the

radio is muted. When you end the call, the radio will automatically be turned back

on. You can also use other functions of the phone, for example write messages or

play games, while listening to the radio.

When an application using a GPRS or HSCSD connection is sending or receiving

data, it may interfere with the radio.

137

Warning: Listen to music at a moderate level. Continuous exposure to

high volume may damage your hearing.

■ Organiser (Menu 7)

Note: Your phone must be switched on to use the functions in

the Organiser menu. Do not switch the phone on when wireless phone use is

prohibited or when it may cause interference or danger.

Alarm clock

The alarm clock uses the time format that has been set for the clock. The alarm

clock works even when the phone is switched off.

Press Menu and select Organiser and Alarm clock.

• Select Alarm time, key in the alarm time and press OK.

To change the alarm time, select On.

• Select Alarm tone and you can select a default alarm tone, personalise your

alarm tone by selecting one from the ringing tone list or from the gallery, or set

the radio as your alarm tone.

If you select the radio as an alarm tone, your phone plays the last radio channel

that you listened to via loudspeaker. If the headset is removed, the default

alarm tone will be used instead of the radio.

138

When the alarm time expires

The phone will sound an alert tone, and flash Alarm! and the current time on the

display.

Press Stop to stop the alarm (if radio is selected as an alarm tone, you can select

whether to leave the radio on). If you let the alarm continue for a minute or if you

press Snooze, the alarm stops for about ten minutes and then resumes.

If the alarm time is reached while the phone is switched off, the phone switches itself on and

starts sounding the alarm tone. If you press Stop, the phone asks whether you want to

activate the phone for calls, Switch the phone on?. Press No to switch off the phone or Yes to

make and receive calls.

Note: Do not press Yes when wireless phone use is prohibited or when it may cause

interference or danger.

Calendar

The calendar helps you to keep track of reminders, calls that you need to make,

meetings, and birthdays.

The calendar uses shared memory, see Shared memory on page 23.

Press Menu and select Organiser and Calendar.

Tip: To quickly view the current Calendar month, move the joystick to the

right in standby mode.

Scroll to the day that you want. The current day is indicated by a frame around the

day. If there are any notes set for the day, the day is shown in bold type.

139

• To view a single note, scroll to the desired note, and press View. You can scroll

through the note.

• To view the list of options, press Options and you can select from making a

note, or sending a note via IR or the Bluetooth connection, or sending a note as

a note or as a text message directly to a compatible phone’s calendar.

• There are options for deleting, editing, moving and repeating a note and for

copying a note to another day.

•

Settings to set the date, time, date or time format, or the first day of the week.

In the Auto-delete option you can set the phone to automatically delete old

notes after a specified time. However, the repeated notes, for example birthday

notes, will not be deleted.

Making a calendar note

For keying in letters and numbers, see Writing text on page 51.

Press Menu and select Organiser and Calendar or move the joystick to the right in

standby mode to go to the monthly view. Scroll to the date that you want, and

press View. Press Add note if there are no notes for the day, or press Options and

select Make a note and select one of the following:

•

Meeting - Key in the subject and press Save (or press Options and search

for the name in Contacts). Key in the location of the meeting, and press Save.

Key in the start time for the meeting and press OK, and then key in the end

time and press OK. To set the alarm for the note, select With tone or Silent (no

alarm tone) and then set the alarm time.

140

•

Call - Key in the phone number, and press Save. Key in the name, and press

Save. (Instead of keying in the phone number, search for the name and number

in Contacts). Key in the time for the call and press OK. To set the alarm for the

note, select With tone or Silent (no alarm tone) and then set the alarm time.

Birthday - Key in the person’s name (or press Options and search for it in

Contacts) and press Save. Then key in the year of birth and press OK. To set the

alarm for the note, select With tone or Silent (no alarm tone) and then set the

alarm time.

•

Memo - Key in the subject and press Save. Key in the end day for the note

and press OK. To set the alarm for the note, select With tone or Silent (no alarm

tone) and set the alarm time.

Reminder - Key in the subject for the reminder, and press Save. To set the

alarm for the note, select Alarm on and set the alarm time.

When you have set the alarm, the indicator

notes.

is displayed when you view the

When the phone sounds an alarm for a note

The phone beeps and displays the note. When a call note indicator

is shown

on the display, you can call the displayed number by pressing

. To stop the

alarm and view the note, press View. Press Snooze and the phone returns to

standby mode. To stop the alarm without viewing the note, press Exit.

141

To-do list

In the to-do list, you can save notes for tasks that you have to do and manage the

tasks in different ways.

The to-do list uses shared memory, see Shared memory on page 23.

Press Menu and select Organiser and To-do list.

• To add a new note when the task list is empty, press Add note, or press Options

and select Add if you have saved tasks. Press Save and select the priority for

the note High, Medium or Low. The phone automatically sets the deadline

without an alarm for the note. To change the deadline, view the note and

select the option for the deadline.

For Dictionary, see Setting predictive text input on or off on page 53.

• In the task list, you can press Options, and select an option, for example to sort

the tasks by priority or by deadline, send them to another phone, save them as

a calendar note, or access the calendar.

• To view a task, scroll to the desired task on the list and press View. To edit the

displayed task, press Edit.

Notes

You can use the Notes application for writing and sending notes via IR, Bluetooth

connection or as a text (SMS) or MMS message to another compatible phone. The

Notes application uses shared memory, see Shared memory on page 23.

1. Press Menu, select Organiser and Notes, or type a character when the

messaging keyboard is open.

142

2. To add a new note, press Add note if the list of notes is empty, or press Options

and select Make a note.

To view a note, scroll to the desired note on the list and press View. To edit the

displayed note, press Edit.

3. Key in the note and press Save.

If you press Options, you can select Insert time & date to add the current time

and date to the note. If there is not enough space for time and date, the phone

will ask you to delete the appropriate number of characters from your note.

If the note is too long to be sent as a message, the phone will ask you to delete

the appropriate number of characters from your note.

Wallet

You can use the wallet to pay for your purchases via the browser. You can save

your personal information, such as credit card numbers and addresses in the

wallet, and then use the data that are saved in the wallet during browsing. You

can also save access codes to mobile services that request a user name and

password.

The data in the wallet are protected with a wallet code that you can define when

you access the wallet for the first time. At Create wallet code: key in the code and

press OK to confirm it and at Verify wallet code: key in the code again and press

OK.

143

If you want to delete all the contents of the wallet and the wallet code, key in

*#7370925538# (*#res wallet# in letters) in standby mode. You also need the

phone’s security code, see Access codes on page 20.

Accessing the wallet

Press Menu and select Organiser and Wallet. Key in your wallet code and press

OK. Select

•

Wallet profiles to create card combinations, for example, for different services.

A wallet profile is helpful if the service asks you to fill in many data items

during browsing. You can select the appropriate wallet profile instead of

selecting different cards separately, see Creating a wallet profile on page 146.

Cards to save personal card information. You can save payment card, loyalty

card and access card information, for example, username and password

combinations, for different services and also addresses and user data. See

Saving card details on page 144.

Tickets to save the notifications of e-tickets that you have bought via mobile

service. To view the tickets, scroll to the desired ticket and press View.

•

Receipts to save receipts for mobile purchases.

Personal notes to save all kinds of personal information that you want to

protect by saving it in the wallet. See Personal notes on page 145.

•

Settings, see Wallet settings on page 147.

Saving card details

1. Press Menu and select Organiser, Wallet and Cards.

144

2. Scroll to one of the following card types to save the details and press Select.

•

Payment card for credit and debit cards.

Loyalty card for membership cards.

Access card for personal usernames and passwords to online services.

User info card for customised personal preferences for online services.

Address cards for basic contact information for home/office.

3. If there are no cards in the folder, press Add new to create a new card.

To view the saved details of the card, scroll to the desired card and press View.

4. Key in a card name or accept the suggested card name, and fill in the fields for

the details.

You can also receive card information to your phone over the air from a card issuer

or service provider. You will be notified as to which category the card belongs to.

Save or discard the received card. You can view, but not edit the saved card. For

the availability of receiving card information over the air, contact the card issuer

or service provider.

Personal notes

You can save personal notes, for example, account numbers, passwords, codes or

notations.

Access the wallet and select Personal notes. To create a new personal note, press

Add new.

To view a note, scroll to the desired note on the list and press View. To edit the

displayed note, press Edit.

145

When viewing a note, you can select the following options Send via text msg.,

Copy to calendar, Use detail or Delete.

Creating a wallet profile

When you have saved your personal card details, you can combine them together

to create a wallet profile. You can use the wallet profile to retrieve wallet data

from different cards while browsing.

1. Access the wallet and select Wallet profiles.

2. To create a new wallet profile, press Add new.

3. Fill in the following fields and press OK. Some of the fields contain data that

are selected from the wallet. You need to save the data before you can create a

wallet profile.

•

Select payment card next - select a card from the payment card list.

Select loyalty card next - select a card from the loyalty card list.

Select access card next - select a card from the access card list.

Select user info card next - select a card from the user data card list.

Select billing address next - select an address from the address card list.

Select shipping address next - select an address from the address card list.

Select receipt delivery address next - select an address from the address

card list.

•

Select receipt delivery method next - select the way to deliver the receipt,

Receipt to phone number or Receipt to e-mail address.

Wallet profile name: enter a name for the profile.

146

Wallet settings

Access the wallet and select Settings. Select

•

Change code to change the wallet code.

RFID to set the RFID code.

Guidelines for paying for your purchases with the wallet

• To do your shopping, access the desired service site that supports the wallet.

See Connecting to a service on page 160.

Choose the product that you want to buy and carefully read all the information

provided before your purchase.

Note: The text may not fit within a single screen. Therefore, make sure to scroll

through and read all of the text before your purchase.

• To pay for the items, the phone asks whether you want to use the wallet or not.

The phone also requests your wallet PIN code.

• Select the card you want to pay with from the Payment card list. Provided that

the data form you receive from the service provider supports the Electronic

Commerce Modelling Language specification, the phone automatically fills in

the credit card information or the wallet profile from the wallet.

• Approve the purchase, and the information is forwarded.

• You may receive an acknowledgement or a digital receipt for the purchase.

• To close the wallet, select Close wallet. If you do not use the wallet for 5

minutes, it will be automatically closed.

147

Note: If you have tried to access or have accessed confidential information

requiring passwords (for example, your bank account), empty the cache of your

phone after each use.

To empty the cache, see Cache memory on page 167.

Synchronisation

Synchronisation allows you to save your calendar, contacts data and Notes on a

remote Internet server (network service) or on a compatible PC. If you have saved

data on the remote Internet server, you can synchronise your phone by starting

the synchronisation from the phone. You can also synchronise the data in your

phone’s contacts, calendar and Notes to correspond to the data on your

compatible PC by starting the synchronisation from the PC. The contact data in

your SIM card will not be synchronised.

Note that answering an incoming call during synchronisation will end the

synchronisation process and you will need to restart it.

Synchronising from your phone

Before synchronising from your phone, you may need to do the following:

• Subscribe to a synchronisation service. For more information on availability

and the synchronisation service settings, contact your network operator or

service provider.

• Retrieve the synchronisation settings from your network operator or service

provider, see Settings for the synchronisation on page 149.

148

• Set the connection settings you need for synchronisation. See Setting up the

phone for a service on page 159.

To start the synchronisation process from your phone:

1. Activate the connection settings that you need for synchronisation. See

Setting up the phone for a service on page 159.

2. Press Menu and select Organiser, Synchronisation, Settings and Active

Internet sync settings. Scroll to the set you wish to activate and press Activate.

Mark the data that are going to be synchronised. See Data to be synchronised

in Settings for the synchronisation on page 149.

3. Press Menu and select Organiser, Synchronisation and Synchronise.

The marked data in the active set will be synchronised after confirmation.

Note that synchronising for the first time or after an interrupted

synchronisation may take up to 30 minutes to complete, if the contacts or

calendar are full.

Settings for the synchronisation

You may receive the synchronisation settings as an over-the-air message from the

network operator or service provider. To receive the settings over the air, see Over-

the-air settings service on page 44.

Keying in the settings manually

1. Press Menu, select Organiser, Synchronisation and Settings.

2. Select Active Internet sync settings. Scroll to the set you wish to activate and

press Activate.

149

You need to activate the set where you want to save the synchronisation

settings. A set is a collection of settings required to make a connection to a

service.

3. Select Edit active Internet sync settings. Select each setting one by one and key

in all the required settings.

•

Settings' name. Key in the name for the set and press OK.

Data to be synchronised. Mark the data you want to synchronise, Contacts,

Calendar, and/or Notes and press Done.

•

Database addresses. Select Contacts database, Calendar database and/or

Notes database.

•

User name. Key in the user name and press OK.

Password. Key in the password and press OK. Verify the password and press

OK.

•

Synchronisation server. Key in the name of the server and press OK.

Connection settings to define connection settings required for

synchronisation. See Keying in the service settings manually on page 160.

Select each of the settings one by one and key in all the required settings.

Contact your network operator or service provider for the settings.

Select PC sync settings to key in the settings for server-alerted

synchronisation. Select and key in the User name and Password.

150

Synchronising from a compatible PC

To synchronise the contacts, calendar and notes from a compatible PC, use an IR

or Bluetooth connection, or a data cable. You also need the PC Suite software of

your phone installed on the PC. Start the synchronisation from the PC using PC

suite.

■ Applications (Menu 8)

Note: Your phone must be switched on to use this function.

Do not switch the phone on when wireless phone use is prohibited or when it may

cause interference or danger.

Games

The games use shared memory, see Shared memory on page 23.

Press Menu and select Applications. A list of folders is shown. Select Games and

select

•

Select game and scroll to a game or a game set (the name depends on the

game) and press Open to launch a game. For functions that you can access by

pressing Options in the game list, see Other options available for an

application or application set on page 152.

Game downloads to download a game to the phone. See Downloading a game

or an application on page 153.

151

•

Memory to view the amount of memory that is available for game and

application installations.

App. settings to set sounds, lights and shakes for the game.

Note that running some games may consume the phone’s battery faster (and you

may need to connect the phone to the charger).

Collection

The collection menu uses shared memory, see Shared memory on page 23.

Press Menu and select Applications. A list of folders is shown. Select Collection

and select

•

Select application and scroll to an application or application set (the name

depends on the application) and press Open to launch an application. For

functions that you can access by pressing Options in the applications list, see

Other options available for an application or application set on page 152.

•

App. downloads to download an application to the phone. See Downloading a

game or an application on page 153.

Memory to view the amount of memory that is available for game and

application installations.

Note that running some applications may consume the phone’s battery faster

(and you may need to connect the phone to the charger).

Other options available for an application or application set

•

Delete to delete the application or application set from your phone.

152

Note that if you delete a pre-installed application or an application set from

your phone, you may be able to download it again to your phone from

www.nokia.com.

•

Details to give additional information about the application.

Update version to check if a new version of the application is available for

download from the services (network service).

•

Web page to provide further information or additional data for the application

from an Internet page. This is a network service and the menu is shown only if

an Internet address has been provided with the application.

Web access to restrict the application from accessing the network. Select Ask

first and the phone will ask you for net access, Allowed to allow net access, or

Not allowed not to allow net access.

Connect via to activate the network connection settings that you want to use

for the application. You can select Default or Internet.

Downloading a game or an application

Your phone supports J2ME Java games and applications. Make sure that the

application or a game is compatible with your phone before downloading it. You

can download new Java applications in different ways (network service):

• Press Menu, select Applications, Collection and App. downloads or press Menu

and select Applications, Games and Game downloads.

The list of available browser bookmarks is shown. Select More bookmarks to

access the list of bookmarks in the Services menu, see Bookmarks on page 165.

153

Select the appropriate bookmark to connect to the desired site. If the

connection fails, you may not be able to access the page with the currently

selected service settings. In this case, enter the Services menu and activate

another set of service settings, see Connecting to a service on page 160. Retry

to connect to the site.

For the availability of different services, pricing and tariffs, contact your

network operator and/or the service provider.

• Press Menu, select Services and Download links to download an appropriate

application or game, see Browsing the pages of a service on page 161.

• Use the Nokia Application installer from PC Suite to download the applications

to your phone.

Note: Nokia does not warrant for applications from non-Nokia sites. If you choose

to download Java applications from them, you should take the same precautions,

for security or content, as you would with any site.

Note that when downloading a game or an application, it may be saved in

the Games menu instead of the Collection menu. Download content only for

sources that you trust.

Extras

Voice recorder

You can record fragments of speech, such as a name and phone number to write

them down later.

154

Note: Obey all local laws governing recording of calls. Do not use this feature

illegally.

Recording

1. Press Menu, select Applications, Extras and Voice recorder.

2. To start the recording, select Record. To start the recording during a call, press

Options, and select Record. While recording a call, all parties to the call will

hear a faint beeping sound.

When recording, hold the phone in the normal position near to your ear.

3. To end the recording, press Stop. The recording will be saved in the Recordings

folder of the Gallery menu.

4. To listen to the last recording, select Play last recorded. To send the last

recording as a multimedia message, or to send it via IR or Bluetooth

connection, select Send.

List of recordings

Press Menu, select Applications, Extras, Voice recorder and Recordings list. The list

of folders in the Gallery is shown. Scroll to Recordings, press Open and you can

select some of the options for files in the Gallery. See Gallery (Menu 5) on page

132.

Calculator

The calculator in your phone adds, subtracts, multiplies, divides, calculates the

square and the square root, and converts currency values.

This calculator has a limited accuracy and rounding errors may occur, especially in long

divisions.

155

1. Press Menu, select Applications, Extras and Calculator.

2. When ’0’ is displayed on the screen, key in the first number of the calculation,

press

for a decimal point or the corresponding symbol on the keyboard,

if the flip is open.

3. Press Optionsand select Add, Subtract, Multiply, Divide, Square, Square root or

Change sign.

If the flip is open, you can also use the corresponding calculation symbols on

the keyboard, if available.

Tip: Alternatively, press

once to add, twice to subtract, three

times to multiply or four times to divide, if you are using the calculator

with the flip closed.

4. Key in the second number.

5. For the total, press Equals. Repeat steps 3 to 5 as many times as is necessary.

6. To start a new calculation, press and hold Clear.

Performing a currency conversion

1. Press Menu, select Applications, Extras and Calculator.

2. To save the exchange rate, press Options and select Exchange rate. Select

either of the displayed options. Key in the exchange rate, press

for a

decimal point, and press OK. The exchange rate remains in the memory until

you replace it with another one.

3. To perform a currency conversion, key in the amount to be converted, press

Options and select In domestic or In foreign.

156

You can also perform the currency conversion in standby mode. Key in the amount

to be converted, press Options and select In domestic or In foreign.

Countdown timer

Press Menu, select Applications, Extras and Countdown timer. Key in the time in

hours and minutes and press OK. If you wish, write a note that will be displayed

when the time expires, and press OK to start the countdown timer.

• To change the countdown time, select Change time, or to stop the timer, select

Stop timer.

If the alarm time is reached when the phone is in standby mode, the phone sounds

a tone and shows the note, if available or Countdown time up. Stop the alarm by

pressing any key. If no key is pressed, the alarm stops automatically within 30

seconds. To stop the alarm and to delete the note, press Exit. Press Restart to

restart the countdown timer.

Stopwatch

You can measure time and take split or lap times using the stopwatch. During

timing, the other functions of the phone can be used. To set the stopwatch to run

in the background, press

Note: Using the stopwatch consumes the battery and the phone's operating time

will be reduced. Be careful not to let it run in the background when performing

other operations with your phone.

157

Taking split times or lap times

1. Press Menu, select Applications, Extras and Stopwatch. Select Split timing or

Lap timing and press Start. You can select Continue if you have set the

stopwatch to run in the background.

2. Press Split to take a split time, Lap to take a lap time or Stop to stop the

timing. You can scroll through the split or lap times shown below the overall

time.

3. Press Save to save the lap or split times as a set of times. To reset the times or

to continue timing, press Options and select Reset or Start.

Viewing and deleting times

Press Menu, select Applications, Extras and Stopwatch.

If the stopwatch has not been reset, you can select Show last to view the most

recent measured time. Select View times and a list of names or the final times of

the time sets is shown. Select the time set that you want to view.

To delete the saved times, select Delete times. Select Delete all or One by one,

scroll to the times that you want to delete, and press Delete.

■ Services (Menu 9)

Note: Your phone must be switched on to use this function.

Do not switch the phone on when wireless phone use is prohibited or when it may

cause interference or danger.

158

Various service providers maintain pages specifically designed for mobile phones,

offering services such as news, weather reports, banking, travel information,

entertainment, and games. With your phone’s multi-mode browser you can view

the services that use Wireless Markup Language (WML) or extensible HyperText

Markup Language (xHTML) or a mixture of both.

Check the availability of these services, pricing and tariffs with your network

operator and/or the service provider whose service you wish to use. Service

providers will also give you instructions on how to use their services.

Since the phone’s display and the memory capacity are much smaller than in a

computer, the appearance of the pages may vary due limited screen size.

Basic steps for accessing and using services

1. Save the service settings that are required to access the service that you want

to use. See page 159.

2. Make a connection to the selected service. See page 160.

3. Start browsing the pages of the service. See page 161.

4. Once you are finished browsing, end the connection to the service. See page

163.

Setting up the phone for a service

You may receive the service settings as an over-the-air message from the network

operator or service provider that offers the service that you want to use. You can

also key in the settings manually or add and edit the settings using PC Suite.

159

For more information and for the appropriate settings, contact the network

operator or service provider that offers the service that you want to use.

To receive the service settings over the air, see Over-the-air settings service on

page 44.

Keying in the service settings manually

1. Press Menu and select Services, Settings and Connection settings.

2. Select Active service settings.

3. Scroll to the connection set that you would like to activate and press Activate.

You need to activate the connection set in which you want to save the service

settings. A connection set is a collection of settings that are required to

connect to a service.

4. Select Edit active service settings.

Select each of the settings one by one and key in all the required settings

according to the information you have received from your network operator or

service provider. Note that all the bearer-related settings are in the Bearer

settings menu.

Connecting to a service

Firstly, make sure that the service settings of the service that you want to use have

been activated. To activate the settings:

160

• Press Menu and select Services, Settings and Connection settings. Select

Active service settings and scroll to the set you want to activate and press

Activate.

Secondly, make a connection to the service. There are three ways to connect:

• Open the start page of the service, for example the homepage of the service

provider:

Press Menu and select Services and Home, or in standby mode, press and hold

. If the flip is open, press the corresponding number key.

• Select the bookmark of the service:

Press Menu and select Services, Bookmarks, and select a bookmark.

If the bookmark does not work with the current active service settings, activate

another set of service settings and try again.

• Key in the address of the service:

Press Menu and select Services and then Go to address. Key in the address of

the service, and press OK.

Note that it is not necessary to add the prefix http:// in front of the address

since it will be added automatically.

Browsing the pages of a service

After you have made a connection to the service, you can start browsing its pages.

The function of the phone keys may vary in different services. Follow the text

guides on the phone’s display. For more information, contact your service

provider.

161

Note that if EGPRS is selected as the data bearer, the indicator

top left of the display during browsing. If you receive a call or a text message, or

make a call during an EGPRS connection, the indicator will be shown on the

is shown on the

top right of the display to indicate that the EGPRS connection has been suspended

(on hold). After the call the phone tries to reconnect the EGPRS connection.

Using the phone keys while browsing

• Move the joystick up or down to browse through the page.

• To select a highlighted item, press the joystick briefly or press

• To enter letters and numbers, press the keys and to enter special

. When the phone’s flip is open, you can key in

characters, press the key

letters and numbers normally.

Options while browsing

Press Options to view the following options that may be available. The service

provider may also offer other options. Select

•

Home to return to the homepage.

Shortcuts to open a new list of options that are, for example, specific to the

page.

•

Add bookmark to save the page as a bookmark.

Bookmarks. See Bookmarks on page 165.

Download links to show the list of bookmarks for downloading.

Save to folder to add a current page as a download link to a selected folder.

162

•

Other options to show a list of other options, for example, options for the

wallet and some security options.

•

Reload to reload and update the current page.

Quit. See Disconnecting from a service on page 163.

Note: If you have tried to access or have accessed confidential information

requiring passwords (for example, your bank account), empty the cache of your

phone after each use.

To empty the cache, see Cache memory on page 167.

Direct calling

The multi-mode browser supports functions that you can access while browsing.

You can make a voice call, send DTMF tones while a voice call is in progress, and

save a name and a phone number from a page.

Disconnecting from a service

To quit browsing and to end the connection, press Options and select Quit. When

Quit browsing? is shown, press Yes.

Alternatively, press

twice. The phone ends the connection to the service.

Appearance settings of the multi-mode browser

While browsing, press Options and select Other options and Appear. settings, or in

standby mode, press Menu and select Services, Settings and Appearance settings.

Select

163

•

Text wrapping and select On if you want the text to continue on the next line

or select Off, if you want it to be abbreviated.

•

Font size and select Small, Normal or Large.

Show images and select No, if you do not want the pictures on the page to be

shown. This can speed up the browsing of pages that contain a lot of pictures.

•

Alerts and select Alert for unsecure connection and Yes to set the phone to

alert when a secure connection changes to an unsecure one during browsing.

Select Alert for unsecure items and Yes to set the phone to alert when a secure

page contains an unsecure item. Note that these alerts do not guarantee a

secure connection. For more information, see Browser security on page 167.

•

Character encoding to select the character set that the phone uses for showing

browser pages that do not include that information or to select whether to

always use UTF-8 encoding when sending a Web address to a compatible

phone.

A cookie is data that a site saves in your phone’s browser cache memory. The data

can be, for example, your user information or your browsing preferences. Cookies

will be saved until you clear the cache memory, see Cache memory on page 167.

1. While browsing, press Options and select Other options, Security and Cookies

or in standby mode, press Menu and select Services, Settings, Security settings

and Cookies.

164

2. Select Allow or Reject to allow the phone to receive, or to prevent it from

receiving cookies.

Bookmarks

You can save addresses as bookmarks in the phone’s memory.

1. While browsing, press Options and select Bookmarks,

or in standby mode, press Menu and select Services and Bookmarks.

2. Scroll to the desired bookmark and press Select or press the joystick briefly to

make a connection to the page associated with the bookmark, or press Options

for the following functions: View, Edit, Delete, Send, New bookmark or Save to

folder.

Note: Your phone may have some pre-installed bookmarks for sites that are not

affiliated to Nokia. Nokia does not guarantee or endorse these sites. If you choose

to access them, you should take the same precautions for security or content as

you would with any Internet site.

Receiving a bookmark

When you have received a bookmark as an over-the-air (OTA) message, press Save

to add it to the bookmark list, or press Options and select View or Discard.

Downloading

1. To download more tones, images, games or applications to your phone, press

Menu, and select Services and Download links.

165

2. Select Tone downloads, Graphic downloads, Game downloads or App.

downloads to download tones, images, games or applications, respectively.

Note: Nokia does not warrant for applications from non-Nokia sites. If you choose

to download Java applications from them, you should take the same precautions,

for security or content, as you would with any site.

Download content only from sources that you trust.

Service inbox

The phone is able to receive service messages (pushed messages) from your service

provider. To set or change the service inbox settings, press Menu, and select

Services, Settings and Service inbox settings. Select

•

Service messages and On to set the phone to receive service messages.

Automatic connection and On to set the phone to automatically fetch the

content indicated in the service message.

To view a received service message, press Show. If you press Exit the message is

moved to the Service inbox. To view the service message later, press Menu and

select Services and Service inbox.

While browsing, press Options and select Other options and Service inbox. Scroll

to the message that you want and press Retrieve to download the marked content

from the web page, or press Options and select Retrieve, Details or Delete.

166

Cache memory

The information or services you have accessed are stored in the cache of your

phone. A cache is a buffer memory that is used to store data temporarily. To empty

the cache:

• while browsing, press Options and select Other options and Clear the cache, or

• in standby mode, press Menu and select Services and Clear the cache.

Browser security

Security features may be required for some services, such as banking services or

shopping on a site. For such connections you need security certificates and

possibly a security module, which may be available on your SIM card. For more

information, contact your service provider.

Security module

The security module can contain certificates as well as private and public keys. The

security module may improve the security services for applications requiring

browser connection, and allows you to use a digital signature. The certificates are

saved in the security module by the service provider.

Press Menu and select Services, Settings, Security settings and Security module

settings. Select

•

Security module details to show the security module title, its status,

manufacturer and serial number.

167

•

Module PIN request to set the phone to request the module PIN when using

services that are provided by the security module. Key in the code and select

On. To disable the module PIN request, select Off.

•

Change module PIN to change the module PIN, if allowed by the security

module. Key in the current module PIN code, then key in the new code twice.

Change signing PIN. Select the signing PIN that you want to change. Key in the

current PIN code, then key in the new code twice.