ES 80
User manual
Before using this appliance please read carefully the user manual
and the safety instructions!
CAUTION
Household and commercial use only. Any servicing other than cleaning and user
maintenance should be performed by an authorized service representative.
• Do not immerse base in water or try to disassemble.
• To reduce the risk of fire or electric shock, do not remove the base, or any user serviceable parts inside.
Repair should be done by authorized service personnel only.
• Check voltage to be sure that the voltage indicated on the name plate corresponds with your voltage.
• Never use warm or hot water to fill the water container. Use cold water only!
• Keep your hands and the cord away from hot parts of the appliance during operation.
• Never clean with scouring powders or sharp implements.
• The cord or any defective element must be replaced exclusively by your Nespresso dealer.
Under no circumstances should you open the machine yourself.
SAFETY INSTRUCTIONS
Read these instructions carefully before using your Nespresso machine.
• Do not plug the machine into anything other than a grounded electrical socket. Verify that the voltage indicated
on the technical specifications plate on the bottom of the unit corresponds to your electrical installation.
• Do not place your Nespresso machine on a hot surface (electrical heating plate for example) or near a flame.
• Attention: Do not draw off hot water while temperatur indicator lamp (red) blinks fast. Strong steam jet
would result instead of hot water - hazard of burning! Cool down the system see Cappuccino «4».
• Do not open the jaw while the machine is functioning since the extraction of coffee is done under high pressure.
• Do not use the machine without the drip tray and grill in place.
• Remove the plug when cleaning your machine.
• Ensure that the electrical cord does not come into contact with sharp or hot objects. Do not disconnect the
electrical plug by pulling on the cord.
• Avoid touching the electrical cord as well as any other part which may become hot during the use of the
machine (steam nozzle, chrome portion of capsule holder).
• Never plunge the machine in water.
• Keep the machine and the electrical cord out of children‘s reach.
• For descaling, adhere to the directions which follow:
2 Preparation: please read carefully the safety instructions on the descaling packaging.
3 Descaling: do not open the jaw and do not use the steam nozzle during descaling process.
4 Rinse: rinse the water tank and clean the machine to avoid any residual descaling agent.
• Do not use the machine if it is damaged or if the cord is in bad condition.
• The cord or any other defective element must be replaced exclusively by an authorized after-sales service center.
Under no circumstances should you open the machine yourself.
Save these Instructions
®
TSM SUCCESS MANUAL Safe to use - easy to understand due to
®
®
TSM - Total Security Management and ergonomic communication
2
251104
Descaling warning:
All green lamps are flashing
Descaling
Nozzle
Remove nozzle/ cappuccinatore
device and adapter
Dismantle the
cappuccino device
1.
2.
Preparation
Machine
off
Recipient
(min. 0.6 l)
Eject capsule
Empty drip tray,
0.1l descaling
Place cloth in case
of steam injection
remove Claris filter agent + 0.5 l water
simultaneously, 3 seconds
Descaling
START:
Lamps
Lever right
Lamps
Lever left
Refill the tank
simultaneously,
3 seconds
Rinse
START:
Lamps
Empty the tanks,
rinse and fill water
tank completely
Lamps
Lever right
Finish
Machine switches off automatically
3
Volume
Factory setting:
40 ml
110 ml
Change setting
Press button M
1
Coffee
or
Hot water
Within 10 seconds
2
Press + hold
or
Lever to the right
Fill cup
3
4
OK
STOP
min. 15 ml
Release button
Lever to the left
Within 10 seconds: Press button M
New volume has been stored
Troubleshooting
No indication
Check plug and fuses
Prewarm cup, hot water without capsule.
Descale if necessary
Coffee is not hot enough
Coffee does not come out
No coffee, water only
Clean, descale if necessary
Clean/insert capsule correctly
Fill water tank
Coffee is not flowing, green
status display lights up
4
Preparation
Temperature indicator:
Switch on
Jaw closed
flashing:
constant: rapid flashing:
heating up ready
too hot
Fill water tank
fresh water
Before the first usage/after a longer period of non-use:
1.
2.
3.
4.
Rinse
Coffee outlet + hot
water/steam nozzle
Place a recipient
on cup tray
Let water flow for
1 minute, press
buttom repeatedly
Let water flow for
1 minute, press
buttom repeatedly
Daily:
1.
2.
Pre-heating/rinsing
ready
2 cups without capsule
5
Espresso
Insert capsule
Place a cup on drip grid
Select small or large
cup
automatic or
STOP
The capsule drops
into capsule
container
Keep system
warm
Eject
capsule
Daily after last
espresso
Capsule container
Some left over
water is normal
6
Lever coffee /
hot water (steam)
Fresh water tank
Handle
Capsule container
(22 capsules)
Cappuccinatore
device
Drip grid
Drip tray
Status display
Call authorized dealer
Reposition lever
Water tank empty
Capsule container full
ON/OFF button
Indicator of temperature
MEMORY lamp/button
Large cup lamp/button
Small cup lamp/button
Hot water button/lamp
Steam button/lamp
7
Cappuccino
Froth milk for
Preparing the milk
Select «steam»
heating up
ready
STOP
Froth OK
Beware of hot nozzle
Temperature change ~55-75°C
ready
STOP
Cool down
system
too hot
Place a recipient
see
Let water flow for 30 seconds
Prepare espresso direct into the frothed up milk
Espresso
8
Cappuccino – Caffe latte: clean after each use
Warm up phase
Deep into fresh water
Beware of hot nozzle
Rinse minimum 10 sec.
STOP
Dismantle and clean cappuccinatore
once a week
9
|