M Systems Flash Disk Pioneers Computer Accessories 91 SR 005 10 7L User Manual

Installation Manual

IM-DOC-021

Using the DiskOnChip^®

with Linux OS

DEC-99

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Contents

Introduction...................................................................................................................................4

Hardware Requirements for the DiskOnChip ..........................................................................4

Requirements for Installation of the DiskOnChip into Linux.................................................5

3.1 Utilities Diskette Content.........................................................................................................5

3.2 Linux Driver for DiskOnChip ...................................................................................................6

Installing the DiskOnChip as an Additional Drive....................................................................7

4.1 Updating the Firmware............................................................................................................7

4.2 Integrating the TrueFFS driver into Linux................................................................................7

Booting Linux from the DiskOnChip........................................................................................13

5.1 Creating a Root File System.................................................................................................13

Troubleshooting.........................................................................................................................16

Additional Information and Tools .............................................................................................18

Appendix I: Making a Root File System...........................................................................................19

Appendix II: Booting from a HDD when the DiskOnChip Firmware is Active ............................22

Appendix III: Applying a Patch Manually..........................................................................................23

How to Contact Us.............................................................................................................................25

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Introduction

M-Systems’ DiskOnChip^âis a family of flash disks. It contains built-in firmware that provides full hard disk

emulation and allows the DiskOnChip to operate as a boot device.

When used under Linux, the DiskOnChip is managed by a device driver, based on M-Systems’ TrueFFS^Ò

(True Flash File System) technology. The TrueFFS driver is attached to the standard Linux file system

[ext2].

M-Systems provides two different TrueFFS drivers for Linux. One driver supports kernel versions 2.0.##

and the other driver supports kernel versions 2.2.##. This Installation Manual can be used for both drivers.

When there are differences in the installation, it will be pointed out in the text.

This Installation Manual note is intended for system integrators designing with the DiskOnChip 2000 or

DiskOnChip Millennium and describes how the DiskOnChip can be installed as an additional disk or as a

boot device under Linux.

It is assumed that the reader is familiar with the Operating System in use.

While the hardware requirements of the DiskOnChip will be briefly discussed, the main part of this

installation manual is related to software installation. This will include basic driver installation and boot issues.

Hardware Requirements for the DiskOnChip

Originally designed for PC environments, the DiskOnChip can also be used in different hardware

environments. The minimum requirements are a 12-bit address bus, an 8-bit data bus, and three active low

control signals (CE#, OE#, WR#). Following is a drawing of the DiskOnChip and its pins. For more

detailed information of the DiskOnChip hardware environment, refer to the various DiskOnChip Datasheets

or to the following Application Notes:

· AP-DOC-10 “Designing with the DiskOnChip”

· AP-DOC-30 “Designing with the DiskOnChip Millennium in a RISC Environment”

· AP-DOC-31 “Designing with the DiskOnChip Millennium in a PC Environment”

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

NC (A16)

NC (A15)

NC (A14)

NC (A13)

VCC

0.1

GND

SA12

SA11

SA10

SA9

SA8

SA7

SA6

SA5

SA4

SA3

SA2

SA1

SA0

A12

A11

A10

DiskOnChip

SD0

SD1

SD2

SD3

SD4

SD5

SD6

SD7

Active Low Chip Enable

Active Low Output Enable

Active Low Write

Figure 1: DiskOnChip Pins

Requirements for Installation of the DiskOnChip into Linux

In order to prepare the DiskOnChip to boot Linux, the following software programs and tools are required:

· Linux should be installed on your HDD. It is possible to check the kernel version by typing the command

uname -r.

· The Linux kernel sources should be installed in Linux (if you don’t have them, refer to kernel-HOWTO at

http://sunsite.unc.edu/LDP/).

If you are about to install Linux, make sure that you also install the kernel sources package and that it is

possible to pass a full compilation of your sources.

· A DOS boot diskette or a HDD that boots DOS.

· M-Systems’ DiskOnChip DOS utilities diskette.

· M-Systems’ TrueFFS driver for Linux.

Note: The latest Disk OnChip DOS utilites can be downloaded from M-System’ website: www.m-sys.co m.

3.1 Utilities Diskette Content

The following files are needed from the DiskOnChip DOS utilities diskette:

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

dformat

dupdate

docpmap

DiskOnChip formatting utility

Utility for updating DiskOnChip firmware

Utility to retrieve information about the DiskOnChip

doc121.ex

DiskOnChip firmware image. “121” is the firmware version, the actual diskette might

contain higher versions of the firmware, e.g. doc122.exb, doc123.exb, etc.

doc2.fff

Alternative firmware image for the DiskOnChip

Note: The file doc2.fff can be found in the \AP012directory when using DiskOnChip DOS utilities

version 1.21 or higher.

3.2 Linux Driver for DiskOnChip

The compressed file driver.tgzcontains the following files:

/usr/src/linux/drivers/block/flash_doc/flobj.obj

TrueFFS device driver core object file

/usr/src/linux/drivers/block/flash_doc/fldrvlnx.c

Source code for driver integration with

kernel

/usr/src/linux/drivers/block/flash_doc/makefile

/tmp/doc-driver/lilo-patch

TrueFFS driver’s makefile

Patch for Lilo to make pLilo

/tmp/doc-driver/plilo

Linux loader, patched to use with the

DiskOnChip

/tmp/doc-driver/lilo.conf

/tmp/doc-driver/boot.b

Lilo sample configuration file

Boot loader, udpated to use with

DiskOnChip

/tmp/doc-driver/copy2doc

/tmp/doc-driver/pam.d/other

Sample scripts, aid tool to create a root file

system

File meant only for Redhat & Caldera,

defines permission access

/tmp/doc-driver/samplefs.txt

Sample root file system listing

/tmp/doc-driver/doc-patch-2.0.##

Patch for kernel sources 2.0.## (only

attached to TrueFFS driver for kernel

versions 2.0.##)

/tmp/doc-driver/doc-patch-example

Example patch for kernel sources 2.2.##

(only attached to TrueFFS driver for kernel

versions 2.2.##)

Note: The included patch files are different for the two TrueFFS drivers. When using the TrueFFS driver for kernel

versions 2.2.##, the kernel needs to patched manually and only an example patch file (/tmp/doc-driver/doc-patch-example)

is provided. Refer to appendix III on how to manually patch your kernel.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Installing the DiskOnChip as an Additional Drive

Before the DiskOnChip can be used as the boot disk for Linux (see Chapter 5), it first needs to be installed

as an additional disk in the system (Linux is booted from a HDD). This chapter describes how to prepare

the DiskOnChip and Linux to configure the DiskOnChip as an additional disk in the system. To achieve this,

the firmware on the DiskOnChip needs to be updated (par. 4.1) and then the TrueFFS device driver needs

to be integrated into Linux (par. 4.2). This is done as follows:

1. Configure Linux with the required devices (par. 4.2.1 Preparing Linux for Integration).

2. Add the TrueFFS driver to the kernel and recompile the kernel (par. 4.2.2 Adding the Driver to the

Kernel).

3. Boot the compiled kernel from your HDD (par. 4.2.3 Booting the Compiled Kernel from HDD).

4. Create a Linux partition on the DiskOnChip (par. 4.2.4 Creating a Linux Partition on the

DiskOnChip).

5. Create a native Linux file system on the DiskOnChip (par. 4.2.5 Creating a Native Linux File System

on the DiskOnChip).

4.1 Updating the Firmware

Before the DiskOnChip can be used as the boot disk or as an additional disk in Linux, it needs to be

formatted with the alternative firmware image.

1. Plug the DiskOnChip into its socket and boot DOS from your HDD.

2. Format the DiskOnChip with the alternative firmware:

dformat /win:d000 /s:doc2.fff /y

Note: If you receive the error: “No DiskOnChip 2000 (R) was found at D000:0”, then run the DOS command docpmap /i

to find out at which address the DiskOnChip is located.

4.2 Integrating the TrueFFS driver into Linux

4.2.1Preparing Linux for Integration

To prepare Linux for integration of the driver, perform the following steps:

Note: To perform these steps, you must be logged in as the superuser (root).

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

1. The floppy drive must be active. Verify this by typing:

# mount

If the /dev/fd0 doesn’t appear in the first column, type:

# mount/dev/fd0 /mnt

From this point, it is assumed that the diskette that contains the TrueFFS driver for Linux is mounted at

/mnt.

2. The kernel sources must be installed. To check this, type:

# ls /usr/src/linux

If this directory exists, then the kernel sources are installed. If not, refer to http://sunsite.unc.edu/LDP/ or

type:

zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more

3. Unzip and untar the file driver.tgz, located on your diskette, as follows:

# cd /tmp

# mkdir temp

# cd temp

# tar -zxvf /mnt/driver.tgz

# cp -rf . /

# cd ..

# rm -fr temp

# cd /usr/src/linux/

4. If you are installing the TrueFFS driver for kernel versions 2.0. ##, type the following command:

# patch -p0 < /tmp/doc-driver/doc-patch-2.0.##

This will patch the current kernel sources to include the TrueFFS driver for Linux (with ## = kernel

version). Notice that the patch for the kernel is working only on original kernel sources, and that the patch

is version specific. In case the utility patchis not available in your Linux environment, refer to Chapter 6

“Troubleshooting”.

Note: If you are installing the TrueFFS driver for kernel versions 2.2.##, the kernel sourced need to be patched manually

(see Appendix III "Applying a patch manually"). For your reference, an example patch file is included with the driver.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

5. Configure the kernel as follows:

# cd /usr/src/linux

# make menuconfig

# make config if the last command doesn’t work.

Define your system by marking the correct devices. If you aren’t sure what the purpose of the device is,

then leave it as it is. Make sure that you mark the DiskOnChip as “Y”es under ‘Floppy, IDE and other

devices’. When you are finished, exit and the new configuration will be saved.

For further details about compiling the kernel or how to apply a patch, refer to http://sunsite.unc.edu/LDP/

or type:

# zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more

6. Remove the old object files:

# make clean

4.2.2Adding the Driver to the Kernel

To compile the TrueFFS driver for Linux:

1. Type the following command:

# cd /usr/src/linux/drivers/block/flash_doc

# make

2. Check dependencies:

# cd/usr/src/linux

# make dep

3. Compile the kernel (this may take up to 15 minutes):

# make zImage

If the kernel is compiled successfully, a message similar to the one below should be shown:

Root device is (3, 3)

Boot sector 512 bytes

Setup is 4332 bytes

System is 374 kB

Sync

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Make[1]:Leaving directory ‘/usr/src/

linux-2.0.32/arch/i386/boot’

If there are any compilation errors, refer to Chapter 6 “Troubleshooting”.

4.2.3Booting the Compiled Kernel from HDD

The new compiled kernel needs to be booted from the HDD. The following steps need to be performed:

1. Type the following commands:

# cp /usr/src/linux/arch/i386/boot/zImage/doc2000

# vi /etc/lilo.conf

2. Add the following lines at the bottom of the file (press ‘INS’ to edit the file and save and exit by typing

<Esc>, ‘:’, ‘w’, ‘q’):

image = /doc2000

root = /dev/hda1

label = doc2000

read-only

Note: The device /dev/hda1points to the HDD that Linux boots from. hda1is the first partition (1) on the first IDE

hard disk (a), hdb2is the second partition (2) on the second IDE hard disk (b), etc. If it is not clear which device it is, look

at the start of the file lilo.confand search for the line first root = ...)

3. Make the inodes for the DiskOnChip:

# cd /dev

# mknod fla b 62 0

# mknod fla1 b 62 1

# mknod fla2 b 62 2

# mknod fla3 b 62 3

# mknod fla4 b 62 4

Number 62 stands for major device number. Since it is hard coded into the driver, no other number would

work.

4. Run Lilo (Linux Loader) to create the map for the kernel and make sure that “doc2000” is listed (if not,

return to the beginning of paragraph 4.2.3):

# lilo

5. Load the updated kernel with the TrueFFS, perform the following steps:

6. Reboot the computer and load Linux.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

7. When the Lilo prompt is displayed, press <Ctrl> or <Alt> or <Tab>. The screen will show :

Lilo boot:

8. Load the recompiled kernel:

Lilo boot:doc2000

4.2.4Creating a Linux Partition on the DiskOnChip

To create a Linux partition on the DiskOnChip, all the DOS partitions on the DiskOnChip need to be

removed and a Linux partition with the native Linux File system [ext2] needs to be created.

1. Run the fdiskutility.

# fdisk /dev/fla

Note: You may create more than one primary partition. Just make sure that the boot flag of the main partition boot is active.

Note: For further information on the fdiskutility, refer to the man pages.

2. Display the contents of the partition table:

Command(m for help):p

3. Delete all existing partitions, enter each partition number for deletion:

Command(m for help):d

4. Create a new Linux native partition:

Command(m for help): n

Command actione extended

p primary partition (1-4)p

Partition number (1-4): 1

First cylinder (1-XXX): 1

Last cylinder or +size or +sizeM or +sizeK ([1] XXX):XXX

5. Change the type of the partition to Linux native:

Command (m for help): t

Partition number (1-4): 1

Hex code (type L to list codes): 83

6. Make the partition bootable:

Command (m for help): a

Partition number (1-4): 1

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

7. Recheck the partition table:

Command (m for help): p

Disk /dev/fla: 16 heads, 9 sectors, 1002

Cylinder units = cylinders of 144 * 512 bytes

Device boot begin Start End Blocks Id System

/dev/fla1 *

1 1002 72139+ 83 Linux native

8. Save the new partition table (disregard any fdiskwarnings):

Command (m for help): w

9. Reboot the machine to let the new partition table load into memory and load Linux again with the new

compiled kernel. If there is more than one partition, this step is vital.

4.2.5Creating a Native Linux File System on the DiskOnChip

To initialize the file system on the newly created Linux partition on the DiskOnChip

1. Type the following command:

# mke2fs /dev/fla1

Note: When a small capacity DiskOnChip is used (4MB or smaller), more space for inodes needs to be allocated. Type the

following command:

# mke2fs -i 2048 /dev/fla1

2. Mount the file system to a directory:

# mkdir /diskonchip

# mount /dev/fla1 /diskonchip

From now on, it is possible to use the DiskOnChip as an additional disk in your system.

Note: If you have created more than one partition, repeat the last step for each partition (dev/fla1, /dev/fla2,

etc.).

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Booting Linux from the DiskOnChip

Being able to boot Linux from the DiskOnChip makes it possible to use the DiskOnChip as the only disk in

the system, holding the OS itself in addition to all other applications and files.

In order to make a block device bootable on Linux, the kernel and the Lilo program should be copied to the

block device and a root file system needs to be created. Creating a root file system on Linux is necessary, as

from this root file system the kernel is activating several programs, such as:

Initialize all processes

Init

Activate swapping

Swapo

Mount the root and proc

filesystems

Mount

Shell

For further details refer to http://sunsite.unc.edu/LDP/ or type:

#zcat /usr/doc/HOWTO/Bootdisk-HOWTO.gz | more

Warning: Notice that the DiskOnChip firmware (i.e. doc121.exb) collides with Lilo. This means that it

is not possible to load Linux from the HDD after the original firmware is restored (see par. 5.1.4). This

doesn’t mean that the HDD is non-functional. It only means that the alternate firmware (doc2.fff) needs

to be reloaded (see par. 4.1).

If it is required to boot Linux from both the HDD and the DiskOnChip, it is necessary to use both pLilo and

boot.b (provided with the TrueFFS driver). For further details, refer to Appendix II.

5.1 Creating a Root File System

5.1.1Introduction

This section is based on Bootdisk-HOWTO and other experiments. Since each distribution has a different

file location and different installations, it is possible that you won’t succeed in booting Linux the first time

from the DiskOnChip. When you receive errors, follow each error and try to fix things, but reload Linux

from the HDD and remount the DiskOnChip each time.

Note: There are several programs that create a root file system. It is not possible to say that any of them is complete right

now, but they are worth trying. The following program is recommended:

Yard: Yard creates rescue disks (also called boot disks) for Linux. A rescue disk usually contains utilities for diagnosing

and manipulating hard disks and file systems. It is used when it is not possible (or if it is not required) to boot from your

HDD. This package contains mainly perl scripts. Refer to http://www.croftj.net/~fawcet/yard/.

Note: For a sample root file system, refer to the file /tmp/doc-driver/samplefs.txt which is part of the

compressed file driver.tgz.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

5.1.2Overview

A root file system must contain everything that is needed to support a full Linux system. To achieve this, the

disk must include the minimum requirements for a Linux system:

· Basic file system structure

· Minimum set of directories: /dev, /proc, /bin, /etc, /lib, /usr, /tmp

· Basic set of commands: sh, ls, cp, mv, etc.

· Minimum set of config files: rc, inittab, fstab, etc.

· Devices: /dev/hd*, /dev/tty*, /dev/fd0, etc.

· Runtime libraries to provide basic functions used by utilities

5.1.3Populating the File System

From this point on, it is assumed that the DiskOnChip is mounted to the /diskonchipdirectory.

The sample script copy2docthat is provided with the driver is located in directory /tmp/doc-

driver. This sample script is created for RedHat 5, SuSE 5.2 and Caldera and is customized for RedHat

5. It might be necessary to change the script according to your distribution. Files that are specific to a

distribution can be found in the script with the distribution name written after it. To exclude a file, make sure

the ‘#’ mark is present at the beginning of the line. To include a file, make sure the ‘#’ mark is removed.

The sample script only copies the basic files that are needed for booting. For any other operation, it is

necessary to add more files.

To create a root file system based on the sample script copy2doc, perform the following steps:

1. Go to the /diskonchipdirectory:

# cd /diskonchip

2. If necessary, customize the sample script (for other distributions):

# vi /tmp/doc-driver/copy2doc

3. Run the script:

# sh /tmp/doc-driver/copy2doc

4. Create the list of files to be mounted:

# vi /diskonchip/etc/fstab

5. Press <INS> to start editing and insert the following lines:

/dev/fla1 /

/proc

ext2 defaults 1 1

/proc proc defaults 0 0

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Press <ESC>, ‘:’, ‘w’, ‘q’ to save the file. It is possible to

add more devices here (for more information, refer to the man

pages).

6. For RedHat and Caldera it is also necessary to copy the configuration file for the pam library (responsible

for making authentic users):

# cp /tmp/doc-driver/pam.d/other

/diskonchip/etc/pam.d/other

Note: Appendix I explains how to create your own root file system manually. Although this is more complicated than using

the above mentioned sample script, it is highly recommended.

All modules should be placed in /lib/modules/. It is necessary to include at least the programs

insmod, rmmodand lsmod. If it is required to load the modules automatically, then also include

modprobe, depmodand swapout. When using kerneld, include it along with

/etc/conf.modules.

Some system programs, such as login, complain when the file /var/run/utmpand the directory

/var/logdo not exist. To solve this, type the following commands:

# mkdir -p /diskonchip/var/{log,run}

# touch /diskonchip/var/run/utmp

After all the needed libraries and programs are set up, run ldconfigto remake

/etc/ld.so.cacheon the root file system. The cache tells the loader where to find the libraries. To

remake ld.so.cache, type the following command:

# cd /diskonchip

# chroot /diskonchip /sbin/ldconfig

The command chrootis necessary, because ldconfigalways remakes the cache for the root file

system.

5.1.4Copying the Kernel, Updating the Boot Sector and Rebooting

To copy the kernel and to update the boot loader files.

1. Type the following commands:

# mkdir /diskonchip/boot

# cp /usr/src/linux/arch/i386/boot/zImage

/diskonchip/boot/doc2000

# rdev /diskonchip/boot/doc2000 /dev/fla1

# cp /tmp/doc-driver/plilo /diskonchip/sbin

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

# cp /tmp/doc-driver/boot.b /diskonchip/boot

# cp /tmp/doc-driver/lilo.conf /diskonchip/etc

# /diskonchip/sbin/plilo -C /diskonchip/etc/lilo.conf -i

/diskonchip/boot/boot.b -m /diskonchip/boot/map

2. Verify that after the last command, the device doc2000is listed on the screen.

3. If it is required to load other partitions, then the file /diskonchip/etc/lilo.confshould be

edited.

Note: pLilo is the patched Lilo, which ensures that the DiskOnChip firmware will not collide with the Linux bootloader.

The final steps in the process of making the DiskOnChip bootable for Linux are as follows:

1. Unmount the DiskOnChip:

# cd /

# unmount /dev/fla1

2. Reboot and load DOS, and reinstall the original firmware:

A:> dupdate /win:D000 /s:doc121.exb

Note: Always use the latest firmware version. The latest version can be downloaded from M-Systems website (www.m-

sys.com)

3. Reboot the machine and disable the HDD in the BIOS setup or make the DiskOnChip the first boot

device in the system by using the following command:

A:> dupdate /win:D000 /s:DOC110.EXB /FIRST

4. Linux will now boot from the DiskOnChip.

Troubleshooting

Adding more programs to Linux root file system

If the DiskOnChip boots Linux without a problem and it is required to add more programs to the Linux root

file system, then mount the HDD and copy the required files.

DiskOnChip does not boot Linux

There are several errors that you can encounter during boot:

· If the DiskOnChip does not boot at all, follow all the instructions from the start of this Installation Manual.

In addition, remember to update the original firmware of the DiskOnChip (i.e. doc121.exb) with the

alternate firmware (doc2.fff) in order to boot Linux from your HDD.

· If the kernel boots, but it gets stuck on:

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

VFS: Unable to mount -.

Most likely, you forgot to do:

# rdev /diskonchip/boot/doc2000 /dev/fla1

· If the DiskOnChip boots and the kernel is loading, but it gets stuck after:

VFS: Mounted root (ext 2 filesystem) readonly.

Most likely, the initprogram or some if its configuration files weren’t copied.

Cannot log in

If you cannot login when booting Linux from the DiskOnChip, make sure that:

· Your default shell is installed.

· The pam libraries were placed as explained in par. 5.1.3 (only for RedHat and Caldera).

Refer to Appendix II in order to solve this problem.

Kernel does not compile correctly or patch utility is not available

If the kernel does not compile correctly, and the problem is not caused by the TrueFFS driver, refer to

http://sunsite.unc.edu/LDP/ or type:

#zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more

Kernel is too big

When you run pLilo and you receive the error ‘Kernel xxx is too big’, recompile the kernel with the

bzImageoption (In step 0, use make bzImageinstead of make zImage).

For further information, refer to http://sunsite.unc.edu/LDP/ or type:

#zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Additional Information and Tools

Additional information about the DiskOnChip, including Application Notes, can be found at http://www.m-

sys.com.

Additional tools and documents are listed in the following table:

Document/Tool

Description

AP-DOC-10

Designing with the DiskOnChip 2000

AP-DOC-15

Obtaining DiskOnChip 2000 Information

Designing with the DiskOnChip Millennium in a RISC Environment

Designing with the DiskOnChip Millennium in a PC Environment

DiskOnChip 2000 Data Sheet

AP-DOC-30

AP-DOC-31

DiskOnChip 2000 Data Sheet

DiskOnChip Millennium Data Sheet

DiskOnChip Utilities

DiskOnChip DIP EVB

DiskOnChip2000-PIK

DiskOnChip-GANG

DiskOnChip Millennium Data Sheet

DiskOnChip Utilities User Manual

DiskOnChip Evaluation Board

DiskOnChip DIP Programmer and Integrators Kit

1+8 DIP Socket Gang Programmer

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Appendix I: Making a Root File System

To create your own root file system, perform the following steps:

1. Make the following directories:

# cd /diskonchip

# mkdir bin dev etc lib mnt proc sbin tmp usr var

2. Create devices in the /devdirectory. You can either do this manually or just copy the /devdirectory

from the HDD. If you wish to save space, it is possible to remove non-required devices (i.e. if you don’t

have a SCSI drive, then remove all the sd* devices).

# cp -dpR /dev /diskonchip

This command copies many unnecessary inodes to the DiskOnChip. Removing them causes no problem,

as long as you make sure that the ones listed in the sample file system are present.

3. Copy and configure the files in the /etcdirectory:

# cp -dr /etc/rc.d /diskonchip/etc (for RedHat)

# cp -dr /sbin/init.d /diskonchip/sbin (for SuSE)

# cp -d /etc/inittab /diskonchip/etc

4. Copy the password file and make sure that each user has its default shell installed:

# cp /etc/passwd /diskonchip/etc

# cp /etc/shadow /diskonchip/etc (it is possible that you do not have this)

# cp /etc/group /diskonchip/etc

5. Create the file /etc/fsstabthat contains the list of files to be mounted:

# vi /diskonchip/etc/fstab

6. Press <INS> to start editing and insert the following lines:

/dev/fla1 /

/proc

ext2

defaults 1 1

/proc proc

defaults 0 0

Press <ESC>, ‘:’, ‘w’ and ‘q’ to save the file.

Note: It is possible to add more devices here. For more information, refer to the man pages.

7. There are several programs that need to be copied to have a functional environment. Other programs are

not as important, although it would be rather difficult to work without them. All other programs that are

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

not listed below are considered optional. Copy these programs to the directories /binor /sbinas

follows:

# cp /bin/{program_name}

/diskonchip/bin/{program_name}

/bin directory:

cat

echo

hostname

kill

mount

chmod

chown

cut

rmdir

mkdir

mke2fs

mknod

dircolors

sync

umount

uname

e2fsck

/sbin directory:

halt

Shutdown

init

Swapoff

Swapon

Telinit

ldconfig

mingetty

mkswap

reboot

rdev

Update

runlevel

The file name of mingettyvaries with the distribution, i.e. RedHat and SuSE use mingetty,

Slackware uses agetty. To find out what the name of this file in your distribution is, perform a grep on

“getty”:

# grep getty /etc/inittab

8. The /libdirectory contains all the shared libraries and loaders. Only the appropriate libraries need to

be copied to the /libdirectory. To check which libraries are needed, type the following command for

each file in these two directories:

# ldd /sbin/{filename}

# ldd /bin/{filename}

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

For example:

# ldd /sbin/mke2fs

libext2fs.so.2 /lib/libext2fs.so.2

libcom_err.so.2 /lib/libcom_err.so.2

libuuid.so.1 lib/libuuid.so.1

libc.so.5 /lib/libc.so.5

This will show which libraries are needed for the program mke2fs. In this example, it is necessary to copy

the following four libraries:

# cp /lib/ext2fs.so.2 /diskonchip/lib

# cp /lib/libcom_err.so.2 /diskonchip/lib

# cp /lib/libuuid.so.1 /diskonchip/lib

# cp /lib/libc.so.5 /diskonchip/lib

If you have a long list of files to be copied, it is also possible to run the following command:

# ldd /bin/* > lib_list

# more lib_list

Copy the library loaders as follows:

# cp lib/ld.so /diskonchip/lib

(a.out loader)

(elf loader)

# cp /lib/ld_linux.so /diskonchip/lib

It is possible to use objcopyto reduce the size of the libraries. For example:

# objcopy -strip-debug /diskonchip/lib/lib.so.5

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Appendix II: Booting from a HDD when the DiskOnChip Firmware

is Active

Since Lilo and the DiskOnChip firmware (i.e. doc121.exb)share the same area in RAM, the system

will hang during boot when using an unpatched Lilo. Updating Lilo solves this problem. The existing boot

loader needs to be updated as follows:

# /tmp/doc-driver/plilo -i /tmp/doc-driver/boot.b

This command uses the patched Lilo supplied by the TrueFFS driver and patched boot.b, and your

default /etc/lilo.conf. Make sure that you run this command in the Linux that booted from the

HDD.

pLilo is actually forcing you to use smaller kernels because it allocates part of the physical memory to the

driver. Therefore, big kernels (around 470 KB) will have a problem with pLilo (pLilo will stop with an error

‘Kernel xxx is too big’). There are two solutions to this problem:

1. Compile the kernel with the bzImage option (‘make bzImage’). Refer to

/usr/doc/HOWTO/Kernel-HOWTO.gzfor more information.

2. Comment out all big kernels from lilo.conf(only during the installation procedure).

M-Systems provides a patch file to Lilo sources to make pLilo. To activate the patch, you must have the

Lilo sources available on your system. After you verify that the sources are available, type the following

command:

# patch -p0 < lilo-patch

You now have pLilo sources.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

Appendix III: Applying a Patch Manually

There are two ways to integrate the TrueFFS driver into the kernel: manually or with a patch utility.

The TrueFFS driver for kernel versions 2.0.## contains patch files for kernel versions 2.0.29-2.0.35

(/tmp/doc-driver/doc-patch-2.0.##). See paragraph 4.2.1 for detailed information on

how to patch your kernel with these patch files.

When using the TrueFFS driver for kernel versions 2.2.##, the kernel needs to be patched manually. For

your reference, the driver contains an example patch file (/tmp/doc-driver/doc-patch-

example). This appendix explains how to patch the kernel manually.

To patch your kernel manually, go to your local kernel sources:

# cd /usr/src/linux

There are 5 files that you will need to patch:

/usr/src/linux/include/linux/blk.h

/usr/src/linux/include/linux/major.h

/usr/src/linux/drivers/block/Makefile

/usr/src/linux/drivers/block/Config.in

/usr/src/linux/drivers/block/ll_rw_blk.c

Review the example patch file (/tmp/doc-driver/doc-patch-example) provided with the

TrueFFS driver (driver.tgz). The file will look something like this.

--- include/linux/major.h

Tue Aug 12 23:57:23 1997

+++ /tmp/package/usr/src/linux/include/linux/major.h Mon Aug

17 14:05:19 1998

@@ -69,6 +69,8 @@

#define APBLOCK_MAJOR 60 /* AP1000 Block device */

#define DDV_MAJOR

61 /* AP1000 DDV block device */

+#define IGEL_FLASH_MAJOR 62 /* [email protected] 2.6.98 */

#define SPECIALIX_NORMAL_MAJOR 75

#define SPECIALIX_CALLOUT_MAJOR 76

Each of the above mentioned files needs to be edited to create the correct patch for your kernel.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

In the above example, the file /usr/src/linux/include/linux/major.his patched. The

two lines that start with the ‘+’ mark are added to the current source code, and the lines that start with the ‘-

‘ mark are removed from the source code. Repeat this process for all five of the above-mentioned files.

91-SR-005-10-7L REV. 2.0

Using the DiskOnChip with Linux OS

How to Contact Us

Internet:

http://www.m-sys.com

info@m-sys.com

E-mail:

USA Office:

Japan Office:

M-Systems Inc.

M-Systems Japan Inc.

8371 Central Ave, Suite A

Newark CA 94560, U.S.A

Phone: 1-510-494-2090

Fax: 1-510-494-5545

1-11-15 Higashi Gotonda Shinagawa-ku

Tokyo, 141-0022 Japan

Phone: 03-3445-9042

Fax: 03-3445-9045

Taiwan Office:

U.K. Office:

M-System Asia Ltd.

M-Systems UK Ltd.

11F-2, No. 81,Sec.2, Chang Teh Rd. PO Box 20

Taipei, Taiwan, R.O.C.

Phone: 886-2-2550-1741

Fax: 886-2-2550-1745

Chalgrove SPDO

OX44 7YP

Phone: 44 (0) 1865 891 123

Fax: 44 (0) 1865 891 391

Israel Office:

M-Systems Ltd.

Atidim Industrial Park P.O.B 58036

Tel Aviv 61580, Israel

Phone: 972-3-647-7776

Fax: 972-3-647-6668

M-Systems assumes no responsibility for the use of the material described in this document. Information

contained herein supersedes previously published specifications on this device from M-Systems. M-Systems

reserves the right to change this document without notice.

91-SR-005-10-7L REV. 2.0

Mr Coffee SRX55 User Manual
Grindmaster RAPS200 User Manual
Ericsson R250s PRO User Manual
Emerson CK5859 User Manual
Dell PowerVault JY870 User Manual
Black & Decker SPACEMAKER ODC425 User Manual
Audiovox MVX 550 User Manual
Atmel Corp Computer Accessories AT91EB42 User Manual
Arkon MULTI ANGLE DASH SM228 User Manual
AEG KF 2061 AROMA User Manual