(
(
)
MZ360216EX KDC333RCAM4
)
MZ360217EX KDC4033AM4
CD-RECEIVER
INSTRUCTION MANUAL
© B64-3677-00/00 (MW)
Safety precautions
About CD players/disc changers
connected to this unit
2WARNING
To prevent injury or fire, take the
following precautions:
Kenwood disc changers/ CD players released in
1998 or later can be connected to this unit.
Refer to the catalog or consult your Kenwood
dealer for connectable models of disc changers/
CD players.
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools)
inside the unit.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made
by other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players
to this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information
that can be displayed may differ depending on the
models being connected.
• Mounting and wiring this product requires
skills and experience. For safety’s sake, leave the
mounting and wiring work to professionals.
2CAUTION
To prevent damage to the machine, take
the following precautions:
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
•
You can damage both your unit and the CD changer if
you connect them incorrectly.
• Do not place the faceplate (and the faceplate
case) in areas exposed to direct sunlight, excessive
heat or humidity. Also avoid places with too much
dust or the possibility of water splashing.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to
play. In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit still
does not operate normally after a while, consult
your Kenwood dealer.
• Do not subject the faceplate to excessive shock,
as it is a piece of precision equipment.
• When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
Do Not Load 8 cm (3 in.) CDs in the CD
slot
If you try to load a 8 cm (3 in.) CD with its adapter
into the unit, the adapter might separate from the
CD and damage the unit.
English
|
3
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
About DAB Tuner control
(KDC-MP4533/MP4033/MP4033S)
• When you purchase optional accessories, check
with your Kenwood dealer to make sure that they
work with your model and in your area.
Refer to A group on the Instruction manual of DAB
Tuner KTC-9090DAB (optional accessory) for the
control method of DAB Tuner function.
However, the following control methods of the
function for this unit may be differed from the
Instruction manual; therefore, refer to the following
supplemental instruction.
<Auto Ensemble Memory Entry>
1. Select the preset band for Auto Ensemble
Memory Entry.
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when
the Reset button is pressed.
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
2. Press the [AME] button for at least 2 seconds.
Open Auto Ensemble Memory Entry.
After memory storage is finished, the number of
the pre-set buttons and the ensemble label are
displayed.
<Searching by programme type and language>
and <Languages to be displayed> in
<Programme Type (PTY) Function>
At the operation to press [DISP] button, use [AUTO]
button instead.
Reset button
• The characters which can be displayed by this
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;
^ - { } | ~ .
<Automatic Switching DAB priority>
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
This function cannot be used.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. This means that the unit
is utilizing laser beams that are of a weaker class.
There is no danger of hazardous radiation outside
the unit.
If the faceplate is stained badly, wipe the stain off
with a cloth moistened with neutral cleaner, then
wipe it again with a clean soft dry cloth.
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth
or using a volatile liquid such as thinner or alcohol may
scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty,
wipe them with a dry, soft cloth.
|
4
English
About CDs
Handling CDs
Removing CDs
• Do not touch the recording surface of the CD.
When removing CDs from this unit pull them out
horizontally.
CDs that cannot be used
• CDs that are not round cannot be used.
• CD-R and CD-RW are easier to damage than a
normal music CD. Use a CD-R or a CD-RW after
reading the caution items on the package etc.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
When using a new CD
If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen, etc.
.
This unit may not correctly play discs which do
not have the mark.
• You cannot play A CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-
R/CD-RW recorder instruction manual.)
Burrs
CD storage
Burrs
• Do not place CDs in direct sunlight (On the seat
or dashboard etc.) or where the temperature is
high.
• Store CDs in their cases.
CD accessories
Do not use disc type accessories.
CD cleaning
Clean from the center of the disc and move
outward.
English
|
5
About MP3 and WMA
The playable MP3/WMA file (hereafter called
Audio file) and the media format has the following
limitation. The Audio file, which is not conforming
to the specification, may not play normally, or the
file and folder names may not display correctly.
The maximum number of characters for
display
File/Folder name: 64 (Joliet: 32) characters
MP3 ID3 Tag/ WMA Contents property: 30
characters
Playable Audio file
•
MP3, WMA
•
•
File/Folder name is the number of the characters
including the extensions.
MP3 ID3 Tag can only display the tag of Ver1.0/1.1.
•
•
Attach the correct extension for the Audio file (MP3:
".MP3", WMA: ".WMA")
Do not attach the extensions to files other than the
Audio file. If the extension is attached, the file, which is
not the Audio file, will play and outputs a loud noise,
causing damage to the speaker.
The files with copy protection cannot be played.
The settings of your encoding software and the
environment in which it is used may now allow you
to play or view specific audio files. For encoding
specifications and instructions on how to set encoding
software, browse through software help or check with
the developers.
Limitation of structure for the file and the
folder
• Maximum number of directory levels: 8
• Maximum number of folders: 100
• Maximum number of files per folder: 255
•
•
Playing order of the Audio file
The Audio file plays in the order which is written by
writing software. You may be able to set the playing
order by writing the play sequence numbers such
as "01" to "99" at the beginning of the file name.
Example
Playable MP3 file
0
¡
: Folder
: Audio file
CD
(1)
¡!
• MPEG 1/2 Audio Layer 3 file
• Transfer bit rate: 8-320 kbps
• Sampling frequency
: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz
2
¡"
3
Playable WMA file
¡#
¡$
• The file in accordance with Windows Media Audio
(Except for the file for Windows Media Player 9 or
after which applies the new functions)
4
• Transfer bit rate: 48-192 kbps
¡%
• Sampling frequency: 32, 44.1, 48 kHz
• Playing order
Playable media
Playing order after ¡! play.
• CD-ROM, CD-R, CD-RW
➡ ¡", ¡#, ¡$, ¡%...
• File search
Forward file search during ¡# play.
Push the Control knob towards [¢] ➡ ¡$
•
•
CD-RW discs which are quick formatted by the writing
software cannot be used.
When recording to the maximum media capacity at
once, the writing software is set to "Disc at once".
• Folder search
Forward folder search during ¡" play.
Push the Control knob towards [FM] ➡ 3, 4...
• Folder select
Playable disc format
• ISO 9660 Level 1/2
When the selection is set to directory 4, and you
want to skip to the folder 2 at the same level.
Push the Control knob towards [4] ➡ 2
• Joliet
• Romeo
• Long file name.
When the selection is set to directory 3, moves
the level up by folder select.
Push the Control knob towards [AM] ➡ 2
|
6
English
General features
Control knob
Release button
LOUD indicator
Clock display
ATT indicator
Power
Volume
Turning ON the Power
Press the [SRC] button.
Increasing Volume
Turn the [VOL] knob clockwise.
Turning OFF the Power
Press the [SRC] button for at least 1 second.
Decreasing Volume
Turn the [VOL] knob counterclockwise.
Selecting the Source
Attenuator
Turning the volume down quickly.
Press the [SRC] button.
Press the [ATT] button.
Each time you press the button, the Attenuator
turns ON and OFF.
When the Attenuator is ON, the "ATT" indicator
blinks.
Source required
Tuner
CD
External disc* (Optional accessory)
Auxiliary input* (Optional accessory)
Standby (Illumination only mode)
Display
"TUNER"
"CD"
"CD CH"
"AUX EXT"
"STANDBY"
•
* Function of the KDC-MP4533/MP4033/MP4033S.
English
|
7
General features
System Q
Selecting the best sound setting preset for
different types of music.
Adjustment Item Display
Range
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
Bass level
Middle level
Treble level
Balance
"BAS L"
"MID L"
"TRE L"
"BAL"
1 Select the source to set
Fader
"FAD"
Press the [SRC] button.
Exit Audio Control mode (Volume control mode)
2 Select the Sound type
Press the [Q] button.
5 Exit Audio Control mode
Press any button.
Press a button other than the [VOL] knob, [SRC],
When you press the button once, the current
sound setting is displayed.
Each time you press the button, the sound
setting alternates.
[0] and [ATT] button.
Sound setting
Natural
Rock
Pops
Easy
Display
"NATURAL"
"ROCK"
"POPS"
"EASY"
"TOP40"
"JAZZ"
Audio Setup
Setting the Sound system, such as Volume offset
and Loudness.
Top 40
Jazz
1 Select the source to adjust
Press the [SRC] button.
2 Enter Audio Setup mode
•
•
Change each setting value with the <Speaker
Setting> (page 9).
First, select the speaker type with the Speaker setting.
When the value is set up by <Audio Control> (page 8),
"USER" is displayed.
Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
4 Adjust the Audio setup item
Audio Control
Turn the [VOL] knob.
1 Select the source to adjust
Adjustment Item Display
Range
–8 —
ON/OFF
Press the [SRC] button.
Volume offset
Loudness
"V-OFF"
"LOUD"
0
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
•
•
Volume offset: Sets each source’s volume as a
difference from the basic volume.
Loudness: Compensates for low and high tones
during low volume.
When Loudness is ON, "LOUD" indicator
is ON.
4 Adjust the Audio item
5 Exit Audio Setup mode
Turn the [VOL] knob.
Press the [VOL] knob for at least 1 second.
|
8
English
In Audio file source
Speaker Setting
Information
Display
"TITLE"*
"ALBUM"*
"FOLDER"
"FILE"
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
Song title & Artist name
Album name & Artist name
Folder name
File name
Play time & Track number
Clock
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
"P-TIME"
"CLOCK"
2 Enter Speaker Setting mode
Press the [VOL] knob.
In Standby/ Auxiliary input source
3 Select the Speaker type
Turn the [VOL] knob.
Each time you turn the knob, the setting
alternates between the settings shown in the
table below.
Information
Auxiliary input name
Clock
Display
"SRC NAME"
"CLOCK"
3 Exit Switching Display mode
Press the Control knob.
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
"SP OFF"
"SP 5/4"
"SP 6*9/6"
"SP OEM"
•
•
* If the contents of the information cannot be
displayed, Play time or Frequency is displayed.
Album name cannot be displayed in WMA file.
4 Exit Speaker Setting mode
Press the [VOL] knob.
Dimmer Control
You can lower the brightness of the display by
using the dimmer function.
Switching Display
Changing the information displayed.
Press the [ATT] button for at least 1 second.
Each time you press the button for 1 second, the
Dimmer control turns ON or OFF.
When the Dimmer control is ON, "DIM ON" is
displayed.
1 Enter Switching Display mode
Press the Control knob for at least 1 second.
"DISP SEL" is displayed.
2 Select the Display item
Push the Control knob towards [4] or
[¢].
In Tuner source
Information
Frequency
Clock
Display
"FREQ"
"CLOCK"
In CD & External disc source
Information
Disc title
Track title
Play time & Track number
Clock
Display
"D-TITLE"*
"T-TITLE"*
"P-TIME"
"CLOCK"
English
|
9
General features
Theft Deterrent Faceplate
TEL Mute
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
The audio system automatically mutes when a
call comes in.
Removing the Faceplate
Press the Release button.
When a call comes in
"CALL" is displayed.
The faceplate unlocks, allowing you to detach it.
The audio system pauses.
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio
•
•
•
The faceplate is a precision piece of equipment and
can be damaged by shocks or jolts.
Keep the faceplate in its faceplate case while
detached.
Do not expose the faceplate (and the faceplate case)
to direct sunlight or excessive heat or humidity. Also
avoid places with too much dust or the possibility of
water splashing.
system comes back ON.
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio
system comes back ON.
Reattaching the Faceplate
•
To use the TEL Mute feature, you need to hook up
the MUTE wire to your telephone using a commercial
telephone accessory. Refer to <Connection Wires to
Terminals> (page 23).
1 Align the projections on the unit with the
grooves on the faceplate.
Projections
Grooves
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
|
10
English
Tuner features
Control knob
ST indicator
Band display
Frequency display
Preset station number
Tuning
Tuning Mode
Selecting the station.
Choose the tuning mode.
Press the [AUTO] button.
1 Select tuner source
Press the [SRC] button.
Select the "TUNER" display.
Each time you press the button, the Tuning
mode alternates between the modes shown in
the table below.
2 Select the band
Tuning mode
Display
Operation
Automatic search for a station.
Search in order of the stations
in the Preset memory.
Push the Control knob towards [FM] or [AM].
Each time you push the knob toward [FM], it
switches between the FM1, FM2, and FM3 bands.
Auto seek
"AUTO 1"
Preset station seek "AUTO 2"
Manual
"MANUAL" Normal manual tuning control.
3 Tune up or down band
Push the Control knob towards [4] or
[¢].
•
During reception of stereo stations the "ST" indicator
is ON.
English
|
11
Tuner features
Station Preset Memory
Frequency Step Setting
Putting a station in the memory.
Changing the tuning frequency step.
The original setting is FM band 50 kHz, and AM
band 9 kHz.
1 Select the band
Push the Control knob towards [FM] or [AM].
1 Turn the power OFF
2 Select the frequency to put in the memory
Push the Control knob towards [4] or
[¢].
Press the [SRC] button for at least 1 second.
2 Switch the frequency step
While pressing the [1] and [5] button, press
the [SRC] button.
Release your fingers from the button after the
display appears.
3 Put the frequency in the memory
Press the desired [1] — [6] button for at least
2 seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the
memory on each [1] — [6] button.
The frequency step changes to FM band 200 kHz,
and AM band 10 kHz.
•
•
When the same operation is repeated, the frequency
step returns to the original setting.
When the frequency step is changed, the frequencies
in the memory are deleted.
Auto Memory Entry
Putting stations with good reception in the
memory automatically.
1 Select the band for Auto Memory Entry
Push the Control knob towards [FM] or [AM].
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in
the memory Auto Memory Entry closes.
Preset Tuning
Recalling the stations in the memory.
1 Select the band
Push the Control knob towards [FM] or [AM].
2 Recall the station
Press the desired [1] — [6] button.
|
12
English
CD/Audio file/External disc control features
Control knob
Disc number
IN indicator
Play time
Track number
Function of the KDC-MP4533/KDC-MP4033/KDC-
MP4033S
Playing CD & Audio file
Playing External Disc
Playing discs set in the optional accessory disc
player connected to this unit.
When a disc is inserted
Press the [SRC] button.
Select the "CD" display.
Press the [SRC] button.
Select the display for the disc player you want.
•
When a CD is inserted, the "IN" indicator is ON.
Display examples:
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses
or plays.
Display
"CD CH"
"MD CH"
Disc player
CD changer
MD changer
Eject the CD
Press the [0] button.
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses
or plays.
•
•
Disc 10 is displayed as "0".
The functions that can be used and the information
that can be displayed will differ depending on the
external disc players being connected.
English
|
13
CD/Audio file/External disc control features
Function of the KDC-MP4533/KDC-MP4033/KDC-
Fast Forwarding and Reversing
MP4033S
Function of disc changers with remote control
Fast Forwarding
Hold down toward [¢] with the Control
knob.
Direct Disc Search
Doing Disc Search by entering the disc number.
Release your finger to play the disc at that point.
1 Enter the disc number
Press the number buttons on the remote
control.
Reversing
Hold down toward [4] with the Control
knob.
2 Do Disc Search
Release your finger to play the disc at that point.
Press the [+] or [–] button.
Cancelling Direct Disc Search
Press the [38] button.
•
There is no sound while the Audio file is being
searched.
•
Input "0" to select disc 10.
Track/File Search
Searching for a song on the disc or in the Audio
file folder.
Track/File/Disc/Folder Repeat
Push the Control knob towards [4] or
[¢].
Replaying the song, disc in the Disc changer or
Audio file folder you are listening to.
Press the [REP] button.
Each time you press the button, the Repeat Play
alternates between the modes shown in the
tables below.
Function of disc changer/ Audio file
Disc Search/Folder Search
Selecting the disc set in the Disc changer or the
folder recorded on the Audio file media.
In CD & External disc source
Repeat play
Track Repeat
Disc Repeat (In Disc Changer)
OFF
Display
"TRAC REP"
"DISC REP"
"REP OFF"
Push the Control knob towards [FM] or [AM].
In Audio file
Function of remote control
Repeat play
File Repeat
Folder Repeat
OFF
Display
Direct Track/File Search
Doing Track/File Search by entering the track/file
number.
"FILE REP"
"FOLD REP"
"REP OFF"
1 Enter the track/file number
Press the number buttons on the remote
control.
2 Do Track/File Search
Press the [4] or [¢] button.
Cancelling Direct Track/File Search
Press the [38] button.
|
14
English
Function of Audio file
Scan Play
Playing the first part of each song on the disc
or Audio file folder you are listening to and
searching for the song you want to hear.
Folder Select
Quickly selecting the folder you want to hear.
1 Enter Folder Select mode
Press the [F.SEL] button.
"FOLD SEL" is displayed.
During Select mode the folder information is
displayed as shown below.
Folder name display
1 Start Scan Play
Press the [SCAN] button.
"TRAC SCN"/"FILE SCN" is displayed.
2 Release it when the song you want to listen
to is played
Press the [SCAN] button.
Displays the current folder name.
Random Play
2 Select the folder level
Playing all the songs on the disc in random order.
Push the Control knob towards [FM] or [AM].
With the [FM] of the Control knob, you move
1 level down and with the [AM] of the Control
knob, 1 level up.
Press the [RDM] button.
Each time you press the button, Random Play
turns ON or OFF.
When the Random mode is ON, "DISC RDM"/
"FOLD RDM" is displayed.
Selecting a folder in the same level
Push the Control knob towards [4] or
[¢].
With the [4] of the Control knob, you move
to the previous folder, and with the [¢] of the
Control knob, to the next folder.
•
When you push the Control knob toward [¢], the
next random song starts.
Returning to the top level
Press the [3] button.
Function of the KDC-MP4533/KDC-MP4033/KDC-
MP4033S
Function of disc changer
3 Decide the folder to play
Press the Control knob.
Magazine Random Play
Play the songs on all the discs in the disc changer
in random order.
The Folder Select mode releases, and the Audio
file in the folder being displayed plays.
Cancelling the Folder Select mode
Press the [F.SEL] button.
Press the [M.RDM] button.
Each time you press the button, the Magazine
Random Play turns ON or OFF.
When the Magazine Random mode is ON,
"MGZN RDM" is displayed.
Text/Title Scroll
Scrolling the displayed CD text, Audio file text, or
MD title.
•
When you push the Control knob toward [¢], the
next random song starts.
Push the Control knob toward [FM] for at
least 2 seconds.
English
|
15
Menu system
Control knob
Menu display
You can continue by returning to step 2 and
setting other items.
Menu System
Setting beep sound during operation, etc.
functions.
The Menu system basic operation method is
explained here. The reference for the Menu items
and their setting content is after this operation
explanation.
4 Exit Menu mode
Press the [MENU] button.
•
When other items those applicable to the basic
operation method above are displayed, their setting
content chart is entered. (Normally the setting listed at
the top of the chart is the original setting.)
Also, the explanation for items that are not applicable
(<Manual Clock Adjustment> etc.) are entered step
by step.
1 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Push the Control knob towards [FM] or [AM].
Example: When you want to set the beep sound,
select the "BEEP" display.
3 Set the menu item
Push the Control knob towards [4] or
[¢].
Example: When you select "BEEP", each time you
push the knob it alternates between
"BEEP ON" or "BEEP OFF". Select 1 of
them as the setting.
|
16
English
Function of the KDC-MP4533/KDC-MP4033/KDC-
Resetting the Security Code function when
the audio unit is first used after removed
from the battery power source or the Reset
button is pressed
MP4033S
In Standby mode
Security Code
Activating the Security Code disables the usage
of audio unit by someone else. Once the Security
Code is activated, the entry of authorized Security
Code is required to turn on the audio unit when
it is removed from the vehicle. Indication of this
Security Code activation prevents your precious
audio unit from stealing.
1 Turn the power ON.
2 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
Now, you can use the unit.
•
If an incorrect code is entered, "WAITING" is displayed,
and the input prohibition periods shown in the table
below is generated.
•
When you activate the Security Code function, it cannot
be released.
After the input prohibition time lapses, "CODE" is
displayed, and you can reenter the code.
Note, your Security Code is the 4 digit number entered in
your "Car Audio Passport" in this package.
Number of times the
Input prohibited time
incorrect code was input
1 Enter Standby
1
2
3
4
—
5 minutes
1 hour
Press the [SRC] button.
Select the "STANDBY" display.
2 Enter Menu mode
24 hours
Press the [MENU] button for at least 1 second.
When "MENU" is displayed, "CODE SET" is
displayed.
In Standby mode
3 Enter Security Code mode
Press the Control knob for at least 2 seconds.
When "ENTER" is displayed, "CODE" is also
displayed.
Touch Sensor Tone
Setting the operation check sound (beep sound)
ON/OFF.
4 Select the digits to enter
Push the Control knob towards [4] or
[¢].
Display
"BEEP ON"
"BEEP OFF"
Setting
Beep is heard.
Beep canceled.
5 Select the Security Code numbers
Push the Control knob towards [FM] or [AM].
6 Repeat steps 4 and 5, and complete the
Security Code.
7 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When "RE-ENTER" is displayed, "CODE" is also
displayed.
8 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
The Security Code function activates.
•
If you enter a Code different from your Security Code,
you have to start over from step 4.
English
|
17
Menu system
In Standby mode
In CD mode
Manual Clock Adjustment
Supreme Setting
When MP3 or WMA files encoded at a low bit
rate (less than 96 kbps (fs=32k, 44.1k, 48kHz))
are played, this function restores their high
frequency region to approach the sound quality
of equivalents of these files encoded at a high bit
rate. Processing is optimized for the compression
format used (MP3, or WMA), and adjustment is
made for the bit rate used.
1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM].
Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
3 Adjust the hours
Push the Control knob towards [FM] or [AM].
Display
Setting
Adjust the minutes
"SPRM ON"
Plays sound using the Supreme function.
Push the Control knob towards [4] or
[¢].
"SPRM OFF"
Plays the original sound stored in the audio file.
4 Exit Clock adjustment mode
•
The sound effect may be imperceptible depending
on the relationship between the audio file format and
setting.
Press the [MENU] button.
Function of the KDC-MP4533/KDC-MP4033/KDC-
MP4033S
In FM reception
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the
faceplate is removed, warning potential thieves.
CRSC (Clean Reception System
Circuit)
Temporarily have reception alternate from
stereo to mono to reduce multi-path noise when
listening to the FM station.
Display
"DSI ON"
"DSI OFF"
Setting
LED flashes.
LED OFF.
Display
Setting
"CRSC ON"
"CRSC OFF"
The CRSC is ON.
The CRSC is OFF.
•
Strong electrical fields (such as from power lines) may
cause unstable sound quality when CRSC is turned
ON. In such a situation, turn it OFF.
|
18
English
Function of the KDC-MP4533/KDC-MP4033/KDC-
MP4033S
Text Scroll
Setting the displayed text scroll.
Auxiliary Input Display Setting
Display
"SCL AUTO"
"SCL MANU"
Setting
Repeats scroll.
Scrolls when the display changes.
Selecting the display when alternating to
Auxiliary input source.
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX EXT" display.
•
The text scrolled is listed below.
- CD text
2 Enter Menu mode
- Folder name/ File name/ Song title/ Artist name/
Album name
- MD title
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
3 Select Auxiliary input display setting mode
Push the Control knob towards [FM] or [AM].
Select the "NAME SET" display.
In Standby mode
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The selected Auxiliary input display is displayed.
CD Read Setting
When there is a problem with playing a CD with
special format, this setting plays the CD by force.
5 Select the Auxiliary input display
Push the Control knob towards [4] or
Display
"CD READ1"
"CD READ2"
Setting
Play CD and Audio file.
Play CD by force.
[¢].
Each time you push the knob, the display
alternates as listed below.
• "AUX EXT"
• "DVD"
•
Setting "CD READ2" cannot play Audio file.
• "PORTABLE"
• "GAME"
Some music CDs may not play even in the "CD
READ2" mode.
• "VIDEO"
• "TV"
6 Exit Auxiliary input display setting mode
Press the [MENU] button.
•
•
When operation stops for 10 seconds, the name at
that time is registered, and the Auxiliary input display
setting mode closes.
You can only set the Auxiliary input display when the
auxiliary input of optional KCA-S210A is used.
English
|
19
Accessory of the KDC-MP4533/KDC-MP4033/KDC-MP4033S/KDC-MP333RC
Basic Operations of remote control
SRC
VOL
SRC
ATT
ATT
VOL
38
AUD
AUD
38
FM+
AM–
4
¢
4/¢
FM/AM/+/–
DIRECT
/OK
Not used
Not used
ABC
JKL
DEF
GHI
MNO
[0] — [9]
PRS
TUV
WXY
QZ
Loading and Replacing the battery
Basic operations
Use two "AA"/ "R6"-size batteries.
Slide the cover while pressing downwards to
remove it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
[VOL] buttons
Adjusts the volume.
[SRC] button
Each time you press the button, the source
alternates.
For the source alternating order refer to
<Selecting the Source> (page 7).
[ATT] button
Turns the volume down quickly.
When the button is pressed again, the volume
returns to the previous level.
2WARNING
•
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is
accidentally swallowed.
•
Do not set the remote control in hot places such as
above the dashboard.
|
20
English
Audio Control
[AUD] button
Selects the Audio item to be adjusted.
[VOL] buttons
Adjusts the Audio item.
•
Refer to <Audio Control> (page 8) for the operation
method, such as the procedures for Audio control and
others operations.
In Tuner source
[FM]/ [AM] buttons
Selects the band.
Each time you press the [FM] button, the band
alternates between the FM1, FM2, and FM3
bands.
[4]/ [¢] buttons
Tune up or down band.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
In Disc source
[4]/ [¢] buttons
Going forwards and backwards between track/
files.
[+]/ [–] buttons
Going forwards and backwards between disc/
folders.
[38] button
Each time you press the button, the song pauses
or plays.
[0] — [9] buttons
When in <Direct Track/File Search> (page 14) and
<Direct Disc Search> (page 14), enters the track/
file/disc number.
English
|
21
Accessories/ Installation Procedure
Accessories
•
If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chasis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
1
..........1
•
If your car’s ignition does not have an ACC position,
connect the ignition wires to a power source that can be
turned on and off with the ignition key. If you connect
the ignition wire to a power source with a constant
voltage supply, as with battery wires, the battery may die.
If the console has a lid, make sure to install the unit so
that the faceplate will not hit the lid when closing and
opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with
one with the same rating.
Insulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not remove
the caps on the ends of the unconnected wires or the
terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail
to work if you share the - wires or ground them to any
metal part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals
(do not mix front and rear). For example, if you connect
the + connector of the left speaker to a front output
terminal, do not connect the - connector to a rear
output terminal.
2
..........2
..........4
..........4
..........1
•
•
•
3
4
5
•
•
•
•
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Installation Procedure
1. To prevent a short circuit, remove the key from
the ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the
following order: ground, battery, ignition.
5. Connect the wiring harness connector to the
unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
|
22
English
Connecting Wires to Terminals
Front left output (White)/ Front right output (Red)
(KDC-MP4533 only)
Rear left output (White)/ Rear right output (Red)
To Kenwood disc changer/ External optional accessory
(KDC-MP4533/MP4033/MP4033S only)
To connect these leads, refer
to the relevant instruction
manuals.
Fuse (10A)
FM/AM antenna input
Wiring harness
(Accessory1)
If no connections are made, do not let the wire come out from the tab.
Power control wire (Blue/White)
When using the optional power amplifier,
connect to its power control terminal.
P.CONT
Depending on what antenna you are
using, connect either to the control
terminal of the motor antenna, or to the
power terminal for the booster amplifier
of the film-type antenna.
Motor antenna control wire (Blue)
TEL mute wire (Brown)
ANT.
CONT
Connect to the terminal that is grounded
when either the telephone rings or
during conversation.
MUTE
To connect the
Kenwood navigation
system, consult your
navigation manual.
White/Black
White
To front left
speaker
FRONT
L
Gray/Black
Gray
To front right
speaker
FRONT
R
Green/Black
Green
To rear left
speaker
REAR
REAR
L
Purple/Black
Purple
To rear right
speaker
R
Ignition key
switch
Car fuse box
ACC
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
(Main fuse)
Ground wire (Black) - (To car chassis)
Battery
+
–
English
|
23
Installation
non-Japanese cars
Japanese cars
1 Refer to the section <Removing the hard rubber
frame> (page 26) and then remove the hard
rubber frame.
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and
secure the unit with the accessory screws.
Metal mounting strap
(commercially available)
Firewall or metal support
T
N
T/N
T
N
Bend the tabs of the
T: Toyota cars
N: Nissan cars
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
8 mm
MAX.
Self-tapping screw
(commercially available)
8mm
MAX.
3
4
ø5mm
ø5mm
Screw (M4X8)
(commercially available)
Accessory3...for Nissan car
Accessory4 ...for Toyota car
•
Make sure that the unit is installed securely in place. If
the unit is unstable, it may malfunction (for example, the
sound may skip).
•
•
During installation, do not use any screws except for
those provided. The use of different screws might result
in damage to the main unit.
Damage may occur if a screwdriver or similar tool is used
with excessive force during the installations.
|
24
English
Screwing the Faceplate on the Unit
If you want to fasten the faceplate to the main
unit so that it does not fall off, screw in the
provided screws in the holes shown below.
Accessory5
•
Never insert the screw in any other screw hole than the
one specified. If you screw them in another hole, it will
contact and may cause damage to the mechanical parts
inside the unit.
English
|
25
Removing the Unit
Removing the hard rubber frame
Removing the Unit
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
1 Refer to the section <Removing the hard rubber
frame> (page 26) and then remove the hard
rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
Screw (M4X8)
(commercially available)
Lock
Catch
Accessory2
Removal tool
2 When the upper level is removed, remove the
lower two locations.
Accessory2
Removal tool
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
•
The frame can be removed from the bottom side in the
same manner.
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands,
being careful not to drop it.
|
26
English
Troubleshooting Guide
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
? No sound can be heard, or the volume is low.
✔
The fader or balance settings are set all the way to
one side.
☞
Center the fader and balance settings.
✔
The input/output wires or wiring harness are
connected incorrectly.
☞
Reconnect the input/output wires or the
wiring harness correctly. See the section on
<Connecting Wires to Terminals>.
General
? The power does not turn ON.
✔
The fuse has blown.
✔
The values of Volume offset are low.
☞
☞
After checking for short circuits in the wires,
replace the fuse with one with the same
rating.
Turn up the Volume offset, referring to the
section on <Audio Setup> (page 8).
? The sound quality is poor or distorted.
? There’s a source you can’t switch.
✔
One of the speaker wires is being pinched by a
screw in the car.
✔
There’s no media inserted.
☞
Set the media you want to listen to. If there’s
no media in this unit, you can’t switch to each
source.
☞
Check the speaker wiring.
✔
The speakers are not wired correctly.
☞
Reconnect the speaker wires so that each
output terminal is connected to a different
speaker.
✔
The Disc changer isn’t connected.
☞
Connect the Disc changer. If the Disc changer
isn’t connected to it’s input terminal, You can’t
switch to an external disc source.
? The Touch Sensor Tone doesn’t sound.
The preout jack is being used.
✔
? The memory is erased when the ignition is
turned OFF.
☞
The Touch Sensor Tone can’t be output from
the preout jack.
✔
The ignition and battery wire are incorrectly
connected.
Tuner source
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
? Radio reception is poor.
✔
✔
The car antenna is not extended.
? The TEL mute function does not work.
The TEL mute wire is not connected properly.
☞
Pull the antenna out all the way.
✔
The antenna control wire is not connected.
☞
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
? The TEL mute function turns ON even though the
TEL mute wire is not connected.
✔
The TEL mute wire is touching a metal part of the
car.
☞
Pull the TEL mute wire away from the metal
part of the car.
? Even if Loudness is turned ON, high-pitched tone
isn’t compensated for.
✔
Tuner source is selected.
☞
High-pitched tone isn’t compensated for when
in Tuner source.
English
|
27
Troubleshooting Guide
Disc source
Audio file source
? "AUX EXT" is displayed without achieving
? Cannot play an Audio file.
External disc control mode.
✔
The media is scratched or dirty.
✔
Unsupported disc changer is connected.
☞
Clean the media, referring to the CD cleaning
of the section on <About CDs> (page 5).
☞
Use the disc changer mentioned in the
<About CD players/disc changers connected
to this unit> (page 3) of the section on <Safety
precautions>.
? The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
? The specified disc does not play, but another one
plays instead.
☞
Clean the media, referring to the CD cleaning
of the section on <About CDs> (page 5).
✔
The specified CD is quite dirty.
Clean the CD.
✔
The recording condition is bad.
Record the media again or use another media.
☞
☞
✔
The disc is loaded in a different slot from that
specified.
? The Audio file track time isn’t displayed correctly.
✔
---
☞
☞
Eject the disc magazine and check the
number for the specified disc.
There are times when it isn’t displayed
correctly according to the Audio file recording
conditions.
✔
The disc is severely scratched.
Try another disc instead.
☞
? Supreme does not take effect when it is turned
ON.
? A CD ejects as soon as it is loaded.
The CD is quite dirty.
✔
✔
Little high-frequency component.
☞
Clean the CD, referring to the CD cleaning of
the section on <About CDs> (page 5).
☞
Supreme would not take effect with songs
with little high-frequency component.
? Can’t remove disc.
The cause is that more than 10 minutes has
✔
Songs that have not been encoded at bit rates
lower than 96 kbps (fs = 32k, 44.1 k, 48 kHz) or
those that have been encoded at a variable bit
rate cannot be decoded to reproduce their high-
frequency components.
✔
elapsed since the vehicle ACC switch was turned
OFF.
☞
The disc can only be removed within 10
minutes of the ACC switch being turned OFF.
If more than 10 minutes has elapsed, turn
the ACC switch ON again and press the Eject
button.
☞
---
? The disc won’t insert.
There’s already another disc inserted.
Press the [0] button and remove the disc.
✔
☞
? Direct Search can’t be done.
Another function is ON.
Turn Random Play or other functions OFF.
✔
☞
? Track Search can’t be done.
For the discs/folders first or last song.
✔
☞
For each disc/folder, Track Search can’t be
done in the backward direction for the first
song or in the forward direction for the last
song.
|
28
English
READING:
IN (Blink):
The unit is reading the data on the disc.
The messages shown below display your
systems condition.
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
EJECT:
No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
➪ Load the disc magazine properly.
No CD in the unit.
➪ Insert the CD.
PROTECT:
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and
then the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button.
NO DISC:
TOC ERR:
No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
➪ Clean the CD and load it correctly.
NA FILE:
An Audio file is played with a format that
this unit can’t support.
➪ ----
COPY PRO:
A copy-protected file is played.
➪ ----
E-05:
The CD is upside-down.
➪ Load the CD correctly.
BLANK:
Nothing has been recorded on the MD.
NO TRACK:
No tracks are recorded on the MD,
although it has a title.
E-15:
Media was played that doesn’t have data
recorded that the unit can play.
➪ Use media that has data recorded that
the unit can play.
NO PANEL:
E-77:
The faceplate of the slave unit being
connected to this unit has been removed.
➪ Replace it.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"E-77" code does not disappear, consult
your nearest service center.
E-99:
Something is wrong with the disc
magazine. Or the unit is malfunctioning for
some reason.
➪ Check the disc magazine. And then
press the reset button on the unit. If the
"E-99" code does not disappear, consult
your nearest service center.
HOLD:
The protective circuit in the unit activates
when the temperature inside the
automatic disc changer exceeds 60°C
(140°F), stopping all operation.
➪ Cool down the unit by opening
the windows or turning on the air
conditioner. As the temperature falls
below 60°C (140°F), the disc will start
playing again.
LOAD:
Discs are being exchanged in the Disc
changer.
English
|
29
Specifications
Specifications subject to change without notice.
Audio section
FM tuner section
Maximum output power
KDC-MP4533/MP4033/MP4033S/MP433
Frequency range (200 kHz space)
: 87.9 MHz – 107.9 MHz
: 50 W x 4
KDC-MP333/MP333RC
: 45 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 70 dB
Selectivity ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 40 dB
Speaker impedance
: 4 - 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (during disc play)
: 2000 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
AM tuner section
Frequency range (10 kHz space)
: 530 kHz – 1700 kHz
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
Weight
: 1.4 kg
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 1 Bit
Spindle speed
: 1000 – 400 rpm (CLV 2times)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
KDC-MP4533: 0.008 %
KDC-MP4033/MP4033S/MP433/MP333/
MP333RC: 0.01 %
Signal to Noise ratio (1 kHz)
KDC-MP4533: 110 dB
KDC-MP4033/MP4033S/MP433/MP333/
MP333RC: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
|
30
English
|