®
COMPACT DISC PLAYER
AM/FM STEREO CASSETTE RECORDER
MODEL CD-104
OPERATING INSTRUCTIONS
PLAYS MUSIC COMPACT DISCS
•
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
•
RECEIVES AM/FM STEREO BROADCASTS
•
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
•
FM STEREO AND POWER LED INDICATORS
•
2 WAY POWER - AC/DC
•
REQUIRES 8 SIZE “C” BATTERIES (not included)
•
PLEASE READ CAREFULLY BEFORE USE
IB-CD104(TA)-FD-E-043002
ADDITIONAL SAFETY INSTRUCTIONS
1. Power Sources - The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
2. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.
3. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
4. Servicing - The user should not attempt to service the appliance beyond that described in
the operating instructions. All other servicing should be referred to qualified service personnel.
It is the intent of Lenoxx that this product be used in full compliance with the
copyright laws of the United States and that prior permission be obtained from
copyright owners whenever recording songs from the RADIO or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
on the bottom of the set.
IB-CD104(TA)-FD-E-043002
2
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO
YOUR SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you can’t resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
IB-CD104(TA)-FD-E-043002
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
To a wall outlet
BATTERY
COMPARTMENT
NOTE: One blade of plug
and outlet is wider.
AC SOCKET
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord
(located in the battery compartment) into the socket
located at the rear of the player, and the other end
to the wall outlet.
TIP
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again.
The plugs are polarized
and only fit one way into
the wall outlet and back of
the set.
2. Using the player on batteries
Insert 8 size “C” batteries (not supplied) into the
battery compartment.
TIP
To use the player on batteries, disconnect the AC
power cord from the player.
Replace the batteries
when the POWER lamp
dims or when the player
stops operating. Replace
all the batteries with new
ones. Before you replace
the batteries, be sure to
take out the CD from the
player and remember to
check the Battery Safety
Instructions on Page 3.
C
C
C
C
IB-CD104(TA)-FD-E-043002
4
PLAYING A CD
2
1
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION switch to CD position
(power on), the POWER lamp will be on.
1
2
POWER lamp
Lift the right corner of the CD DOOR
marked OPEN to open it and place the
CD in the CD compartment. The label side
of the CD should face upward.
Close the CD DOOR by pushing it down.
The display will show the total tracks on
that CD.
3
4
Press the CD PLAY button, the track
number and “PLAY” will show steady on,
the player plays all the tracks once.
Track number
IB-CD104(TA)-FD-E-043002
5
PLAYING CD TRACKS REPEATEDLY
(REPEAT PLAY)
You can play CD tracks over and over in normal or programmed play mode (see
page 7).
FUNCTION
SWITCH
REPEAT
1. Slide the FUNCTION switch to CD position.
2. Select the track by pressing
or
, and then press
.
3. Press the CD REPEAT button.
To repeat
Press
Display shows:
“REP.”
a single track (song)
Press the REPEAT button once
Press the REPEAT button twice
all the tracks (all songs)
programmed tracks
“REP.A”
During programmed play, press
the REPEAT button twice
“REP.A”
&
“PROG.” flashing
To cancel Repeat Play
Press the REPEAT button until “REP.” and “REP.A” go off in the display.
6
IB-CD104(TA)-FD-E-043002
SELECTING YOUR OWN MUSIC PLAYING ORDER
(Programmed Play)
You can make a program of up to 19
tracks in the order you want them to
be played.
NOTE: Programming is only done during
stop mode.
PROGRAM
1. Slide the FUNCTION switch to CD position.
2. Press the PROGRAM button. The “PROG.” and
“00” will flash in the display.
3. Press
or
to select the tracks you want to
program in the order you want.
4. Press the PROGRAM button to confirm.
5. Repeat steps 3 and 4. You can program up to 19
tracks, and the display will show “
continue to program.
” if you
6. Press
to start programmed play. The “PROG.”
will flash in the display.
To check the order of tracks before play
Press the PROGRAM button, the programmed track number appear in the display
automatically every time you press the PROGRAM button.
PROGRAM
To change the current program
Just create a new program following the programming procedure.
PROGRAM
To cancel Programmed Play
Press the STOP button in programming mode.
7
IB-CD104(TA)-FD-E-043002
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
OPEN THE CD DOOR
VOLUME CONTROL
(at the left side of the set)
BY LIFTING HERE
FUNCTION
SWITCH
BASS BOAST
SWITCH
TIP
When CD play is
paused, “PLAY” will
flash and no music
will play.
To
Press or Adjust
VOLUME control
Adjust the volume
Stop playback
To resume play,
press the PAUSE
button
again,
“PLAY” will stop
flashing and music
will play.
“PLAY” will flash during
pause. Press again to
resume play after pause.
Pause playback
Go to the next track
TIP
FORWARDS
BACKWARDS
If you bump the set
during CD play, the
music will stop or
Go back to the previous
track
skip for
a
few
or
seconds. This is
normal for this type
of player.
Press and hold down while
playing until you find the
point.
Locate a point in a song
Lift the CD DOOR (press
STOP first).
Remove the CD
Turn off the power
Hear more bass
8
Slide the FUNCTION switch
to TAPE position.
Slide the BASS BOOST
switch to ON position.
IB-CD104(TA)-FD-E-043002
LISTENING TO THE RADIO
2
1
3
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION switch to
RADIO position, the POWER lamp
will be on.
1
Slide the BAND switch to AM, FM
or FM ST. you prefer.
2
3
Tune into the station you prefer
using the TUNING control (at the
right side of the set). Adjust for
the clearest sound.
This FM STEREO indicator will
FM STEREO
light up when receiving FM
Stereo broadcasts.
4
9
IB-CD104(TA)-FD-E-043002
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME
CONTROL
FUNCTION
SWITCH
TIP
To
Slide or Adjust
Next time you want to
•
listen to the radio, just
slide the FUNCTION
switch to RADIO. The
player automatically
starts playing the
VOLUME control (at the
left side of the set)
Adjust the volume
Slide the FUNCTION
switch to TAPE position
Turn off the Radio
previously
station.
tuned
To improve broadcast reception
Change position of the antenna for FM or FM Stereo.
Move the set itself for AM.
IB-CD104(TA)-FD-E-043002
10
PLAYING A TAPE
2
3
1
Connect the supplied AC power cord or batteries (see page 4).
TAPE PLAY DIRECTION
Slide the FUNCTION
switch to TAPE position.
1
2
3
A
EMPTY
REEL
FULL
REEL
Press the STOP/EJECT
button to open the tape
compartment and insert
a recorded tape. Close
the door.
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
Press the PLAY button.
The player turns on and
starts playing.
When the set finishes
playing this side of the
tape, the set will stop.
To hear the other side
of the tape, flip the tape
over, then insert and
press PLAY.
OK
NO
AUTO STOP
4
OK
NO
11
IB-CD104(TA)-FD-E-043002
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
VOLUME
CONTROL
PAUSE
PLAY
FAST F.&REWIND
STOP/EJECT
To
Press or Adjust
VOLUME control (at the left side
of the set)
Adjust the volume
STOP/EJECT button
Stop playback
Fast forward or rewind
the tape
FAST FORWARD button or
REWIND button
PAUSE button
Press again to resume play after
pause.
Pause playback
Eject the cassette
To shut power off
STOP/EJECT button
Make sure cassette buttons are
all up (stop) and FUNCTION switch
is in the TAPE position (power off).
12
IB-CD104(TA)-FD-E-043002
RECORDING ON A TAPE
2
3
1
4
Connect the supplied AC power cord or batteries (see page 4).
Press the STOP/EJECT button to
TAPE PLAY DIRECTION
1
2
open the tape compartment and
insert a blank tape. Select the
program source (AM, FM, CD, or
built-in microphone) you want to
record.
A
EMPTY
REEL
FULL
REEL
To record from the CD player, insert
a CD and follow the steps to play a
CD (see page 5).
To record from a radio, slide the
FUNCTION switch to RADIO
position, and tune into the station
you want (see page 9).
To record from the built-in
microphone, leave the FUNCTION
switch at the TAPE position, and
speak in front of the set.
Press the RECORD button to start
recording. (The PLAY button is
depressed automatically.)
3
4
OK
NO
To hear what you recorded, slide
the FUNCTION switch to TAPE
position, then press REWIND and
PLAY.
OK
NO
IB-CD104(TA)-FD-E-043002
13
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
TIP
• For best recording
effect, use the AC
power instead of
batteries.
PAUSE
STOP/EJECT
Press or Adjust
To
• To
erase
a
recording, just start
a new recording,
and the old one is
a u t o m a t i c a l l y
replaced.
STOP/EJECT button
Stop recording
PAUSE button
Press the button again to
resume recording.
Pause recording
Turn off the power
Press the STOP/EJECT
button.
IB-CD104(TA)-FD-E-043002
14
PRECAUTIONS
On Safety
On Power Sources
For battery operation, use 8 size “C”
As the laser beam used in the CD
•
•
batteries. We recommend alkaline
batteries for longer life.
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet. Refer servicing to
qualified personnel only.
When the batteries will not be used
•
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage or corrosion.
Should any solid object or liquid fall
•
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
On Operation
On Placement
If the player is brought directly from a
•
Do not leave the player in a location
•
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate. If the player has not been
used for a long time, set it in the
playback mode to warm it up for a few
minutes before inserting a cassette.
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
Do not place the player on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
prolong the life of its components.
This CD player is designed to be
•
If the player is left in a car parked in
•
played on
a
stable no vibration
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the
sun.
position. If you bump the set during
CD play, the music will stop or skip for
a few seconds. This is normal for this
type of player.
Since a strong magnet is used for the
•
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the player to
prevent possible damage from the
magnets.
IB-CD104(TA)-FD-E-043002
15
PRECAUTIONS (continued)
Notes on CDs
Notes on Cassettes
Before playing, clean the CD with a
Break off the cassette tab from side A
•
•
cleaning cloth. Wipe the CD from the
center out.
or B to prevent accidental recording.
Side A
Do not use solvents such as benzene,
•
Tab for side A
Tab for side B
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Do not expose the CD to direct
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
Do not stick paper or stickers on the
CD, nor scratch the CD.
•
To reduce the chances of tape
•
jamming or tangling, you should check
that there are no loose layers of tape
visible through the cassette center
window. If any, tighten these loose
layers of tape using a pencil before
inserting the cassette into the set.
After playing, store the CD in its case.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
IB-CD104(TA)-FD-E-043002
16
MAINTENANCE
Cleaning the Lens
Notes for Storing
Cassette Tapes
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner and blower.
1. Do not put a tape near a magnetic
field, such as a TV, or speaker.
Magnetic fields may reduce the tape
sensitivity or even erase the
recording.
2. Do not store tape for any length of
time in a hot, moist or dusty place.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and
the capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, insert a tape when the
areas cleaned are completely dry.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzene.
RECORD/PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
CAPSTAN
COTTON SWAB
NOTE: In order to see and clean the
head, you may have to press
PLAY first.
IB-CD104(TA)-FD-E-043002
17
TROUBLE SHOOTING
Remedy
Problem
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the FUNCTION switch is at the
right position as you want.
Adjust the volume.
•
•
•
•
There is no sound.
“
” appears in the display
Insert the CD with the label side up.
even when a CD is in place.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
Take out the CD and leave the CD DOOR
open for about an hour to dry moisture
condensation.
•
•
•
CD does not play.
Make sure the FUNCTION switch is at CD
position.
•
Clean the CD, or replace it if the CD is
badly damaged.
Place the player in a location free from
vibration.
•
•
The sound drops out.
Check if your batteries are fresh.
•
•
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
The sound is weak or has
poor quality.
Make sure the safety tab on the cassette
is in place.
Make sure the FUNCTION switch is at tape
position.
•
•
The RECORD button does
not function/The tape does
not play.
Clean the erasing head (see page 17).
Replace all the batteries with new ones
if they are weak.
•
•
The tape does not erase
completely.
Make sure the tape is inserted properly.
Make sure the safety tab of the cassette
is in place.
•
•
The tape does not record.
Clean the heads, pinch roller and capstan
(see page 17).
The sound is weak/The
sound quality is poor.
•
•
The tape has reached its end. Remove
it, flip to the other side and re-insert.
Cassette PLAY button pops
up.
IB-CD104(TA)-FD-E-043002
18
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 12 Watts
DC 12V (8 size “C” batteries)
(Alkaline batteries are recommended)
1
Speakers:
2 - 3 / ” 8 ohm
2
Output power:
Dimensions:
1.5W/channel
Width: 12”
Depth: 8”
Height: 6”
Weight: 5LBs (without batteries)
CD Section
Plays disc type:
Laser wavelength:
Any normal CD used in portable players
760 - 800 NM
Tracking method:
3 - spot error detection
3.86 mm lens
Frequency response:
50Hz - 15kHz (+1/-2 dB)
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CDRW encoded discs.
Tape Recorder Section
Frequency response: Standard normal bias cassette tape,
70Hz - 10kHz
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 kHz
LENOXX reserves the right to make design and specification changes for
product improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR
LACQUER FINISH.
© 2002 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
IB-CD104(TA)-FD-E-043002
19
|