KDC-X895
KDC-BT848U
KDC-X595
KDC-448U
CD-RECEIVER
INSTRUCTION MANUAL
Before reading this manual, click the button below to check the latest edition and the
modified pages.
Check the latest edition
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new
CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space
provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or
service on the product.
Model KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U Serial number
US Residence Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© 2010 Kenwood Corporation All Rights Reserved.
IM327_Ref_K_en_00
HD Radio™ tuner control
54
Basic Operation
Station preset memory
Preset tuning
Auto memory
Seek mode setting
iTunes tagging
Direct access tuning
HD Radio setting
Satellite radio tuner (Optional accessory)
control
Basic operation
Category and Channel search
Channel preset memory
Preset tuning
Channel scan
Direct access tuning
Seek mode setting
58
62
Electronic serial number display
Basic operations of remote control
General control
In Tuner source
HD Radio source
In CD/Audio file source
In iPod source
In Satellite radio tuner source
Hands-free phone control
Appendix
64
66
68
Troubleshooting guide
Specifications
English
|
3
Before use
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Exit Demonstration
Mode> (page 4) of Quick start guide.
About discs used with this unit
• This unit can only play the CDs with
• The following discs cannot be used:
- Discs that are not round
- Discs with coloring on the recording surface or
discs that are dirty
- Recordable/Rewritable disc that has not been
finalized (For the finalization process, refer to
your disc writing software, and your disc recorder
instruction manual.)
- 8 cm (3 inch) disc (Attempt to insert using an
adapter can cause malfunction.)
.
2WARNING
To prevent injury or fire, take the following
precautions:
• Stop the car before operating the unit.
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Handling discs
¤
CAUTION
• Do not touch the recording surface of the disc.
• Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too high
may cause an accident.
• Wipe off the dirt on the panel with a dry silicon or
soft cloth.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use any accessories for the disc.
• Do not use any solvents to clean discs. Use a dry
silicon or soft cloth.
• Clean from the center of the disc and move
outward.
Failure to observe this precaution may result in
damage to the monitor or unit.”
• When removing discs from this unit, pull them out
horizontally.
• Remove the rims from the center hole and disc
edge before inserting a disc.
Cleaning the connector
Wipe off dirt on the connector of the unit and panel.
Use a cotton swab or cloth
Condensation
When the car is air-conditioned, moisture may collect
on the laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the moisture
to evaporate.
How to reset your unit
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
Reset button
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
|
4
KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
5
Component names
Function setting
1 2 3 4
5
6
Function setting operation
Preferences of this unit can be set in the Function
setting mode. For detailed setting procedure and
items, refer to the explanation for each source
function.
1 Select the source
Press the [SRC] button.
w
q
p
9
8 7
Switch to the source to display the items to set.
1 [ ] button
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Release button
3 [SRC] button
4 Control knob
5 [PRESET] button
6 [0] button
3 Select the Function item
Turn the Control knob to display the item to
set, and then press the Control knob.
Press the [
] button to return to the previous
item.
Example:
Play Mode
Settings
7 USB terminal
8 Auxiliary input
AUX Name Set
9
KDC-X895 KDC-BT848U
Clock&Date
Summer Time
[
] [
] button
Initial Settings
Clock Adjust
KDC-X595 KDC-448U
DISP&ILLUMI
Date Mode
[iPod] button
In this Instruction manual, the procedure to select
“Clock Adjust” item in the Function setting layer as
above is described as the following example:
“Settings” > “Clock&Date” > “Clock Adjust”.
o [LOG] button
q [DISP] button
w [
] button
4 Determine the setting value
Turn the Control knob to display the value to
set, and then press the Control knob.
The previous item is displayed.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
6
KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Audio adjustments
Audio control
⁄
• You can set Bass, Middle, and Treble for each source.
About Supreme
You can adjust following Audio Control items;
Display
Audio item
Subwoofer level
Bass Boost
Preset Equalizer
curve
Range
–15 — +15 (dB)
Level1/Level2/OFF
“Rock”/“Pops”/“Easy”/
“Top40”/“Jazz”/ ”Game”/
“Natural”/“User”‡
Technology to extrapolate and supplement with proprietary
algorithm, the high-frequency range that is cut off when
encoding at low bit rate (less than 128Kbps, Sampling
frequency is 44.1kHz).
Supplementing is optimized by compression format (AAC,
MP3 or WMA) and processed according to bit rate.
The effect is negligible with music that is encoded at high
bit rate, variable bit rate or has minimal high frequency
range.
“SubWoofer Level”
“Bass Boost”
“System Q”
“Bass Adjust”
“Bass Center FRQ” Bass Center
40/50/60/70/80/100/
120/150 (Hz)
–8 — +8 (dB)
1.00/1.25/1.50/2.00
OFF/ON
Frequency*
Bass level
• About Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
“Bass Level”
“Bass Q Factor” Bass Q Factor*
“Bass EXT”
Bass Extend*
- When “2Zone” is set to “ON”, the main source sound and
AUX input sound are output to the front speakers and rear
speakers separately.
- Set up the channel of sub source by “2Zone”.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by Control knob.
- Adjust the volume of Rear channel by “2Zone Rear
Volume”.
“Middle Adjust”
“Middle Center
FRQ”
“Middle Level”
“Middle Q Factor” Middle Q Factor* 1.0/2.0
“Treble Adjust”
Middle Center
Frequency*
Middle level
0.5/1.0/1.5/2.0 (kHz)
–8 — +8 (dB)
“Treble Center FRQ” Treble Center
10.0/12.5/15.0/17.5 kHz
Frequency*
- The Audio Control has no effect on sub source.
- When Bluetooth audio source is selected, set “2Zone F/R
Select” to “Rear”. “2Zone” cannot be turned “ON” when this
is set to “Front”. While “2Zone” is turned “ON”, “2Zone F/R
Select” function is disabled.
“Treble Level”
“Balance”
“Fader”
Treble level
Balance
Fader
–8 — +8 (dB)
Left 15 — Right 15
Rear 15 — Front 15
“2Zone Rear Volume” Rear volume during 0 — 35
Dual zone
1 Select the source to adjust
“SubWoofer”
“Detailed Settings”
“HPF Front”
Subwoofer output OFF/ON
Press the [SRC] button.
2 Enter Audio control mode
Front High Pass
Filter
Through/40*/60*/80/
100/120/150/180/220*
Press the Control knob.
(Hz)
3 Select the Audio item to adjust
Turn the Control knob to select the audio item
for adjustment and then press the Control
knob.
“HPF Rear”
Rear High Pass Filter Through/40*/60*/80/
100/120/150/180/220*
(Hz)
50*/60/80/100*/120/
Through (Hz)
“LPF SubWoofer” Low Pass Filter
Press the [
] button to return to the previous
“SubWoofer Phase” Subwoofer Phase Reverse (180°)/
Normal (0°)
Dual Zone System ON/OFF
“2Zone F/R Select” Dual Zone output Rear/Front
channel
item.
4 Adjust the Audio item
“2Zone”
Turn the Control knob to display the value to
set, and then press the Control knob.
The previous item is displayed.
“Supreme”
Supreme setting ON/OFF
“Audio Preset”
Audio Preset
Recall/Memory
5 Exit Audio control mode
memoy†
Press the [
] button for at least 1 second.
“Volume Offset
ADJ”
Volume offset
–8 — 0 (dB)
(AUX: -8 — +8)
*Function of KDC-X895/ KDC-X595.
‡“User”: The customized Bass, Middle, and Treble levels are
effective.
English
|
7
Audio adjustments
Audio preset Memory
Audio preset recall
Registering the value setup by Audio Control.
Recalling the sound setup registered by <Audio
1 Setup Audio control
1 Select the source
Press the [SRC] button.
2 Enter Audio control mode
Press the Control knob.
2 Enter Audio control mode
Press the Control knob.
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” > “Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” > “Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select the Audio preset memory
Turn the Control knob to select “Memory”, and
then press the Control knob.
4 Select the Audio preset recall
Turn the Control knob to select “Recall”, and
then press the Control knob.
5 Turn the Control knob to select “YES”, and
then press the Control knob.
“Memory Completed” is displayed.
5 Turn the Control knob to select “YES”, and
then press the Control knob.
“Recall Completed” is displayed.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
⁄
• Register 1 pair of Audio Preset Memory. You cannot register
by the source.
• When you press the Reset, all the sources will be the setting
value which is registered.
• The following items can be registered.
“Bass Center FRQ”, “Bass Level”, “Bass Q Factor”, “Bass EXT”,
“Middle Center FRQ”, “Middle Level”, “Middle Q Factor”,
“Treble Center FRQ”, “Treble Level”, “SubWoofer Level”, “HPF
Front”, “HPF Rear”, “LPF SubWoofer”, “SubWoofer Phase”
|
8
KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
iPod control operation
For basic operation to playback iPod contents, refer
to the Quick Start Guide.
Alphabet search
You can select an alphabetic character from the
list in the browse item (artist, album, etc.) currently
selected.
Music search
1 Enter Music search mode
Press the [ ] button twice.
“MUSICSEARCH” is displayed.
Searching for the song you want to play.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Select Alphabet search mode
Turn the Control knob to select “Alphabet
Search”, and then press the Control knob.
2 Search for music
3 Search for character
Operation type
Operation
Operation type
Operation
Movement between items Turn the Control knob.
Select the characters
Determine the characters.
Turn the Control knob.
Press the Control knob.
Move to the Alphabet
search mode
Press the [ ] button for at least 1
second. Refer to <Alphabet search>
Return to the Music search mode.
Selection of item
Press the Control knob.
Cancelling the Alphabet search mode
Return to previous item
Return to Top menu
Press the [ ] button.
Push the Control knob towards left for at
least 1 second.
Press the [
] button for at least 1 second.
⁄
• The time of Alphabet search may become long depending
on the number of items (songs) in iPod.
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
• To search for a character other than A to Z and 1, enter “*”.
• If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
⁄
• If no characters included in a song name can be displayed,
the browse item name and digits are displayed.
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
English
|
9
iPod control operation
Related search
Direct search
Browsing for music of the same artist or genre as
the one being played.
Searching for music by selecting a browse item and
an alphabetic character(s).
1 Enter Search select mode
1 Enter Search select mode
Press the [ ] button for at least 1 second.
Press the [ ] button for at least 1 second.
2 Select Related search mode
2 Select Direct search mode
Turn the Control knob to select “Related
Search”, and then press the Control knob.
Turn the Control knob to select “Direct Search”,
and then press the Control knob.
3 Select desired browsing item
3 Select browse item
Turn the Control knob to select browse item,
and then press the Control knob.
Turn the Control knob to select browse item,
and then press the Control knob.
Display
Browses music
Display
Browses item
“Search Artist”
“Search Album”
Displays the album of the same artist.
Displays music in the album in which the one
being played is included.
“PLAYLISTS”
Playlists
“ARTISTS”
Artists
“Search Genre”
Displays the artist of the same genre.
“ALBUMS”
“SONGS”
Albums
Songs
“Search Composer” Displays the album including music created by the
same composer.
“PODCASTS”
“GENRES”
Podcasts
Genres
4 Search for music
Operation type
Operation
Movement between items Turn the Control knob.
“COMPOSERS”
Composers
Selection of item
Return to previous item
Press the Control knob.
Press the [ ] button.
4 Select the character to be searched for
Turn the Control knob to select character, and
then press the Control knob.
Cancelling the Related search mode
Press the [ ] button for at least 1 second.
You can select up to three characters.
⁄
5 Search for music
• Related search cannot be performed while playing a
Podcast.
Turn the Control knob to select “DONE”, and
then press the Control knob.
A search result list is displayed.
• When the music being played has no information on
browsing items or no music was found, “Not Found” is
displayed.
6 Select the music
Turn the Control knob to select music, and then
press the Control knob.
Cancelling the Direct search mode
Press the [
] button for at least 1 second.
|
10 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Skip search
Skip search ratio setting
The number of songs to be skipped is determined
by the ratio of the total number of songs in the list
which is selected.
Sets the ratio of skip performed with <Skip search>
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Enter Function setting mode
2 Enter Search select mode
Press the Control knob for at least 1 second.
Press the [ ] button.
3 Select the Skip search
3 Select Skip search mode
The item can be selected and determined as
follows.
Turn the Control knob to select “Skip Search”,
and then press the Control knob.
“Settings” > “Skip Search”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Search for music
Operation type
Operation
4 Set the Skip search ratio
Movement between items Turn the Control knob.
Skip Search
Push the Control knob towards up or down.
Turn the Control knob to select ratio (“0.5%”,
“1%”, “5%”, or “10%”), and then press the
Control knob.
Selection of item
Sets the ratio of skip
performed
Press the Control knob.
Push the Control knob towards right or left.
5 Exit Function setting mode
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
Press the [
] button for at least 1 second.
⁄
• The ratio of the Skip Search is set to 0.5% as default. Refer to
• Keep pushing Control knob for 3 seconds or longer skips
songs at 10% regardless of the setting.
English
|
11
iPod control operation
Play mode
Registering a song in the playlist
You can select a Play Mode, such as Random play
and Repeat play.
You can register your favorite songs to make a
playlist. You can register up to ten songs in the
playlist.
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
1 Play the song you want to register
Push the Control knob towards up, down, right,
and left.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Search select mode
Press the [ ] button for at least 1 second.
3 Select the Play mode
Turn the Control knob to select “Play Mode”,
and then press the Control knob.
3 Register the song
Turn the Control knob to select “Register My
Playlist”, and then press the Control knob.
“## (registration number) Stored” is displayed. You
can register up to ten songs.
4 Select the desired Play function
Turn the Control knob to select Play function,
and then press the Control knob.
Display
“Play Mode”
Overview
In Music search mode
“iPod by Hand” When set to“ON”, allows you to operate iPod
with the control on the iPod.
4 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
“ON” / “OFF”
“Folder Random” When set to“ON”, plays the music in the folder
randomly. (Music only)
5 Play the song you want to register
“ON” / “OFF”
“All Random”
“File Repeat”
When set to“ON”, plays all songs in iPod
randomly. (Music only)
“ON” / “OFF”
When set to“ON”, plays the music repeatedly.
“ON” / “OFF”
6 Enter Register playlist mode
Press the [ ] button.
7 Register the song
Turn the Control knob to select “Register My
Playlist”, and then press the Control knob.
“## (registration number) Stored” is displayed. You
can register up to ten songs.
(
: Factory setting)
5 Set the Play function
Press the Control knob.
The previous item is displayed.
⁄
6 Exit Function setting mode
• When creating a playlist, you can register the songs stored
in one iPod. If you attempt to register a song by connecting
an unregistered iPod, “My Playlist Delete” is displayed.
Selecting “YES” deletes the playlist.
Press the [
] button for at least 1 second.
• If you attempt to register the eleventh song, “Memory Full”
is displayed and you cannot register the song. To register it,
delete an unnecessary song.
• Do not register Podcasts. Songs may be registered or played
improperly. For example, unintended songs are registered.
|
12 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Playing the playlist
Deleting a song from the playlist
1 Enter Search select mode
1 Enter Search select mode
Press the [ ] button for at least 1 second.
Press the [ ] button for at least 1 second.
2 Select Recall playlist mode
2 Select Delete playlist mode
Turn the Control knob to select “Recall My
Playlist”, and then press the Control knob.
Turn the Control knob to select “Delete My
Playlist”, and then press the Control knob.
3 Play a song in the playlist
3 Select how to delete song(s)
Turn the Control knob to select the song you
want to play, and then press the Control knob.
Turn the Control knob to select “Delete One” or
“Delete All”, and then press the Control knob.
Selecting “Delete All” deletes all songs.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
⁄
• To stop playing the song in the playlist, turn the power off.
• If a song does not end with 1 second or longer silence, its
last portion may not be played.
4 Select the song to delete
• Songs cannot be played at random during playback of the
songs in playlist.
Turn the Control knob to select the song, and
then press the Control knob.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
In Function setting mode
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Playlist delete mode
The item can be selected and determined as
follows.
“Settings” > “My Playlist Delete” > “Delete One”
or “Delete All”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Selecting “Delete All” deletes all songs.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
4 Select the song to delete
Turn the Control knob to select the song, and
then press the Control knob.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
13
Music disc/Audio file (CD or USB) Operation
For basic operation to playback Music disc/Audio
file contents, refer to the Quick Start Guide.
Music Editor media
Skip search
The number of songs to be skipped is determined
by the ratio of the total number of songs in the list
which is selected.
Music search
1 Enter Music search mode
Press the [ ] button.
Selecting the music you want to listen to from the
device or media being played now.
“MUSICSEARCH” is displayed.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Enter Search select mode
Press the [ ] button.
3 Select Skip search mode
2 Search for music
Audio file
Turn the Control knob to select “Skip Search”,
and then press the Control knob.
Operation type
Movement between
folders/files
Selection of folder/flie Press the Control knob.
Return to previous folder Press the [ ] button.
Operation
Turn the Control knob.
4 Search for music
Operation type
Operation
Movement between items Turn the Control knob.
Skip Search
Selection of item
Sets the ratio of skip
performed
Push the Control knob towards up or down.
Press the Control knob.
Push the Control knob towards right or left.
Return to root folder
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button for at least 1 second.
mode
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
¡ indicator: Audio file
] indicator: Folder
⁄
• The ratio of the Skip Search is set to 0.5% as default. Refer to
• Keep pushing Control knob for 3 seconds or longer skips
songs at 10% regardless of the setting.
CD source
Operation type
Movement between track Turn the Control knob.
Operation
Selection of track
Press the Control knob.
Return to first track
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button.
mode
|
14 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Function of remote control
Play mode
Direct music search
You can select a Play Mode, such as Random play
and Repeat play.
Searching the music by entering the track number.
1 Select CD/ USB source
Press the [SRC] button.
Select the “CD” or “USB” display.
1 Enter Direct Music search mode
Press the [DIRECT] button on the remote
control.
“– –” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter the music number
Press the number buttons on the remote
control.
3 Select the Play function mode
Turn the Control knob to select “Play Mode”,
and then press the Control knob.
3 Search the music
Press the [4] or [¢] button on the remote
control.
4 Select the desired Play function
Turn the Control knob to select Play function,
and then press the Control knob.
Cancelling Direct music search
Press the [
] button on the remote control.
Display
Overview
“Play Mode”
“Track Scan”(CD)/ When set to“ON”, plays the intro of the music
“File Scan”(Audio in the disc/folder successively.
file)
“ON” / “OFF”
“Disc Random”(CD)/ When set to“ON”, plays the music in the folder
“Folder Random” randomly.
(Audio file)
“ON” / “OFF”
“All Random”
When set to“ON”, plays all songs in CD/USB
randomly. (Audio file only)
“ON” / “OFF”
“Track Repeat”(CD)/ When set to“ON”, plays the music repeatedly.
“File Repeat”(Audio “ON” / “OFF”
file)
“Disc Repeat”(CD When set to“ON”, plays the music in the disc/
changer)/“Folder folder repeatedly.
Repeat”(Audio file) “ON” / “OFF”
“MGZN Random” When set to“ON”, plays the music in the disc
changer randomly. (Disc changer only)
“ON” / “OFF”
(
: Factory setting)
5 Set the Play function
Press the Control knob.
The previous item is displayed.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
15
Music disc/Audio file Operation
Function of disc changers
Basic operation of Disc changer
(Optional)
Function of disc changers with remote control
Direct search in Disc changer
(Optional)
Searching the disc or music by entering the disc or
music number.
Selecting CD changer source
Press the [SRC] button.
Select the “CD CH” display.
1 Enter Direct search mode
Press the [DIRECT] button on the remote
control.
Music search
Push the Control knob towards right or left.
“– –” is displayed.
Disc search
2 Enter the disc or music number
Press the number buttons on the remote
control.
Push the Control knob towards up or down.
3 Search the disc
Press the [FM] or [AM] button on the remote
control.
4 Search the music
Press the [4] or [¢] button on the remote
control.
Cancelling Direct search
Press the [
] button on the remote control.
⁄
• Input “0” to select disc 10.
|
16 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
17
Tuner Operation
For basic operation to listen to the radio, refer to the
Quick Start Guide.
Seek mode setting
Selects the tuning mode of the radio.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
Auto memory
Memorizes 18 (FM)/ 6 (AM) stations with good
reception automatically.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
3 Select the Seek mode
The item can be selected and determined as
follows.
“Settings” > “Seek Mode”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Auto memory mode
The item can be selected and determined as
follows.
“Settings” > “Auto Memory”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Set to the desired Seek mode
Tuning mode
Display Operation
Auto seek
“Auto1” Automatic search for a station.
Preset station seek “Auto2” Search in order of the stations in the
Preset memory.
Manual
“Manual” Normal manual tuning control.
4 Start Auto memory mode
Turn the Control knob to select Seek mode, and
then press the Control knob.
Turn the Control knob to select “YES”, and then
press the Control knob.
5 Exit Function setting mode
When 18 (FM)/ 6 (AM) stations that can be received
are put in the memory, auto memory entry closes.
Press the [
] button for at least 1 second.
|
18 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Function of remote control
Tuner setting
Direct access tuning
Sets the tuner items.
Entering the frequency and tuning.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
1 Enter Direct access tuning mode
Press the [DIRECT] button on the remote
control.
2 Enter Function setting mode
“– – – –” is displayed.
Press the Control knob for at least 1 second.
2 Enter the frequency
3 Select the Setting mode
Press the number buttons on the remote
Turn the Control knob to select “Settings”, and
then press the Control knob.
control.
Example:
4 Select the desired Tuner setting item
Turn the Control knob to select Tuner setting
item, and then press the Control knob.
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[9], [2], [1]
[8], [1], [0]
Display
“Settings”
“MONO”
Overview
3 Search the frequency
Press the [4] or [¢] button on the remote
control.
You can reduce the noise when stereo
broadcasts are received as monaural.
“ON” / “OFF”
Switches to the traffic information
automatically when the traffic bulletin starts
“ON” / “OFF”
Cancelling Direct access tuning
“TI”
Press the [
] button on the remote control.
(
: Factory setting)
5 Set the Tuner setting item
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
19
Tuner Operation
PTY (Program Type)
Program Type preset
Selecting the Program Type below and searching
for a station;
Putting the Program Type in the Preset button
memory and quick recall.
Program Type Display
Program Type Display
Presetting the Program Type
Speech
Music
“Speech”
“Music”
“News”
Soft
“Soft”
1 Select the Program Type to preset
Nostalgia
Jazz
“Nostalga”
“Jazz”
News
Information
Sports
Talk
“Inform”
“Sports”
“Talk”
Classical
R & B
Soft R & B
Language
Religious Music “Rel Musc”
Religious Talk “Rel Talk”
Personality
Public
“Classicl”
“R & B”
“Soft R&B ”
“Language”
2 Enter Program Type preset mode
Press the [PRESET] button.
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“1” – “6”), and then press the Control
knob for at least 2 seconds.
Rock
“Rock”
Classic Rock
Adult Hits
Soft Rock
Top 40
Country
Oldies
“Cls Rock”
“Adlt Hit”
“Soft Rck”
“Top 40”
“Country”
“Oldies”
“Persnlty”
“Public”
“College”
“Weather”
Cancelling the Preset Memory mode
College
Weather
Press the [
] button.
• Speech and Music include the Program type shown
below.
Recalling the preset Program Type
1 Enter PTY mode
Speech: Items in the white letters.
Music: Items in the black letters.
Press the [ ] button twice.
1 Enter PTY mode
2 Enter Preset memory mode
Press the [ ] button twice.
Press the [PRESET] button.
2 Select the Program Type
3 Select the number you want to recall from the
memory
Turn the Control knob.
Turn the Control knob to select recall number
(“1” – “6”), and then press the Control knob.
3 Search for the selected Program Type station
Push the Control knob towards right or left.
4 Exit PTY mode
Press the [
] button.
⁄
• This function cannot be used during a traffic bulletin or AM
reception.
• When the selected Program Type is not found, “No PTY” is
displayed. Select another Program Type.
|
20 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
21
Log memory
Log memory recall
Log memory item lock
This unit automatically memorizes the previously
used functions and Function setting items, which
can easily be recalled.
Locks Log memory items to avoid them being
deleted.
1 Display the Log memory list
1 Display the Log memory list
Press the [LOG] button.
Press the [LOG] button.
2 Lock the Log memory item
2 Recall the desired function
Turn the Control knob to select item, and then
press the Control knob for at least 1 second.
Locked items are indicated with “ ”.
Turn the Control knob to select function, and
then press the Control knob.
Category display
“FM”
“AM”
“iPod”
“USB”
“CD”
Function category
FM broadcast
AM broadcast
iPod music
USB music
CD music
3 Exit Log memory
Press the [
] button.
“PLAY”
“INIT”
“SET”
Play mode item
Initial setting item
Setting item
“DISP”
“AUD”
“BT”
“SR”
“XM”
Display setting item
Audio control setting
Calling number
Sirius channel
XM channel
Cancelling the Log memory recall
Press the [ ] button.
⁄
• Maximum of 15 recently used functions are logged. When
this limit is reached, they are deleted from the oldest.
• Functions to be logged can be set by categories. Refer to
• Logged functions can be locked to avoid them being
• Stations are logged after 2 minutes of reception.
This timing can be changed. Refer to <Tuner Log memory
|
22 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Deleting a Log memory item
Log memory category setting
Deletes Log memory items.
Sets the function category to be logged.
1 Enter Function setting mode
1 Enter Function setting mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
2 Select the Log delete mode
2 Select the Log memory setting mode
The item can be selected and determined as
follows.
The item can be selected and determined as
follows.
“Settings” > “Log” > “Log Delete”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Log” > “Log Settings”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the Log memory item to delete
Turn the Control knob to select Log memory
item, and then press the Control knob.
Selecting “All” deletes all Log memory. (exclude a
locked items.)
3 Set the category to be logged
Category display
“Tuner Log”
“Data CD Log”
“iPod Log”
Setting category
Radio-related
CD-related
iPod-related
“USB Log”
“Phone Log”
“Function Log”
USB-related
Call-related
Function setting-related
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
Turn the Control knob to select category, and
then press the Control knob.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
4 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
23
Log memory
Tuner Log memory time setting
You can set the timing to log the station by the
reception time.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Tuner log time set mode
The item can be selected and determined as
follows.
“Settings” > “Log” > “Tuner Log Time Set”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Set the reception time for the timing to start
logging the station
Turn the Control knob to select time (“10SEC”,
“30SEC”, “1MIN”, “2MIN”, or “5MIN”), and then
press the Control knob.
4 Exit Function setting mode
Press the [
] button for at least 1 second.
|
24 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
25
Display settings
Selecting display type
Selecting text display
Shown below are examples of display types.
Changes displayed information on each of the
following sources:
Display type Display information
Type A
Type B
Type C
Type D
Type E
Displays 3 lines of text.
Displays 2 line of text.
Displays the clock.
Displays the spectrum analyzer.
Displays off.
In Tuner source
Information
Frequency & Program Service name (FM)
Song title (FM)*
Artist name (FM)*
Title & Artist name (FM)**
Station name (FM)
Radio text + (FM)
Radio text (FM)
Frequency (AM)
Spectrum analyzer & Clock
Date
Display
“Frequency/PS”
“Song Title”
“Artist Name”
“Title/Artist”
“Station Name”
“Radio Text Plus”
“Radio Text”
“Frequency”
“Speana/Clock”
“Date”
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Display type select mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Display Select” >
“Type Select”
Blank
“Blank”
*Dispaly type A only
**Dispaly type B only
To select the item, turn the Control knob. To
determine the item, press the Control knob.
In HD Radio (Optional accessory) source
3 Select the Display type
Information
Display
Turn the Control knob to select Display type,
and then press the Control knob.
Frequency
Station name
“Frequency”
“Station Name”
“Title/Artist”
“Album/Artist”
“Title”
4 Exit Function setting mode
Title & Artist name (KTC-HR300 only)
Album & Artist name (KTC-HR300 only)
Title (KTC-HR200 only)
Spectrum analyzer & Clock
Date
Press the [
] button for at least 1 second.
“Speana/Clock”
“Date”
Blank
“Blank”
In CD & External disc source
Information
Disc title
Track title
Display
“Disc Title”
“Track Title”
“P-Time”
Play time
Spectrum analyzer & Clock
Date
“Speana/Clock”
“Date”
Blank
“Blank”
|
26 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
In Audio file/ iPod source
Information
1 Enter Function setting mode
Press the Control knob for at least 1 second.
Display
Song Title*
Album name*
Artist name*
Title & Artist name**
Album & Artist name
Folder name
“Song Title“
“Album Name”
“Artist Name”
“Title/Artist”
“Album/Artist”
“Folder Name”
“File Name”
“P-Time”
2 Select Text display selection mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Display Select” >
“Text Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
File name
Play time
Spectrum analyzer & Clock
Date
Blank
“Speana/Clock”
“Date”
“Blank”
3 Select the text display part
Push the Control knob towards up or down.
The selected text display part blinks.
*Dispaly type A only
**Dispaly type B only
4 Select the text
Turn the Control knob.
In Standby/ Auxiliary input source
5 Exit Function setting mode
Information
Source name
Spectrum analyzer & Clock (AUX only)
Clock (Standby only)
Date
Blank
Display
Press the [
] button for at least 1 second.
“Source Name”
“Speana/Clock”
“Clock”
“Date”
“Blank”
⁄
• If the selected display item does not have any information,
alternative information is displayed.
• Setting is available when the Display type is A or B which
allows text display. Refer to <Selecting display type> (page
26).
In SIRIUS (Optional accessory) source
Information
Channel Name
Artist Name, Composer name, & Music Title
Category Name
Channel Number
Spectrum analyzer & Clock
Date
Display
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder name” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
“Channel Name”
“Artist/Song”
“Category Name”
“Channel Number”
“Speana/Clock”
“Date”
Blank
“Blank”
Information
Music title
Folder name
File name
Display
In XM (Optional accessory) source
“TITLE***”
“FLD***”
“FILE***”
Information
Channel Name
Name & Title
Category Name
Channel Number
Spectrum analyzer & Clock
Date
Display
“CHANNEL NAME”
“NAME/TITLE”
“CATEGORY”
“CHANNEL NUMBER”
“Speana/Clock”
“Date”
Blank
“Blank”
In Bluetooth Audio “BT AUDIO EXT” (Optional
accessory KCA-BT200, KCA-BT300) source
Information
Display
Source name
Spectrum analyzer & Clock
Date
“Source Name”
“Speana/Clock”
“Date”
Title & Artist name (KCA-BT300 only)
Album & Artist name (KCA-BT300 only)
Blank
“Title/Artist”
“Album/Artist”
“Blank”
English
|
27
Display settings
Information display setting
Illumination color selection
Sets side and graphic parts of the display.
Selecting the Illumination Color of the panel.
1 Enter Function setting mode
1 Enter Function setting mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
2 Select the Display select mode
The item can be selected and determined as
follows.
2 Select Color select mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Display Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “DISP&ILLUMI” > “Color Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the desired Information display setting
item
3 Select the part where you want to set the
Illumination Color
Turn the Control knob to select Display setting
item, and then press the Control knob.
Display
“Color Select”
“ALL”
Part
All
Display
Overview
“Display”
“Key”
“USB&AUX”
Display
Button
“Display Select”
“Side Select”
Sets the side part display for Type A, B, and D.
1 / 2 / 3
USB terminal and Auxiliary input
“Graphic Select”
“Status”
Sets the Type C clock display and Type D
spectrum analyzer display.
1 / 2
Sets the status display (ON/OFF indicator for
each function) for Type A and B.
“ON” / “OFF”
Turn the Control knob to select part, and then
press the Control knob.
4 Select the Illumination Color
Turn the Control knob to select color, and then
press the Control knob.
(
: Factory setting)
Select the color from “Variable Scan”/ “Color1” —
4 Set the Display setting item
“Color24”.
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
Adjusting RGB values
You can create your original color during the
selection from “Color1” — “Color24.”
The color you created can be called when you
select “User”.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
1. Press the Control knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Operation type
Operation
To select the color to adjust. Push the Control knob towards right
(red, green, or blue)
To adjust color.
or left.
Turn the Control knob.
(Range: 0 – 9)
3. Press the Control knob.
Exit the detail color adjustment mode.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
28 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
“ILLUMI Dimmer” Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
Display & Illumination setting
Sets the display and illumination.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
“OFF”: Does not dim the illumination.
2 Select Display & Illumination setting mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“ILLUMI Effect”
Sets whether the key illumination color is
changed in conjunction with the key operation.
“ON” / “OFF”
Sets whether the key illumination color is
changed in conjunction with the sound
volume.
“ILLUMI Music
SYNC”
“ON” / “OFF”
3 Select the desired Display & Illumination
setting item
Turn the Control knob to select Display &
Illumination setting item, and then press the
Control knob.
(
: Factory setting)
4 Set the Display & Illumination setting items
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
Display
Overview
5 Exit Function setting mode
“DISP&ILLUMI”
Press the [
] button for at least 1 second.
“DISP ILLUMI OFF” When“Type E”(Display off) is selected in
whether to turn off display only or display and
key illumination.
“DISP&ILLUMI” / “DISP”
“Display Dimmer” Dims the display part in conjunction with the
light switch of the vehicle.
“Auto”: Dims the display in conjunction with
the Light switch of the vehicle.
“Manual1”: Dims the display constantly.
“Manual2”: Dims the display darker than
Manual1.
“OFF”: Does not dim the display.
“Contrast”
Sets the display contrast.
“1” – ”10” – “30”
“DISP NEGA/POSI” Switches the panel display between positive
or negative.
“NEGA1”: Displays the text in the negative.
“NEGA2”: When the interior light is off, the
text is displayed in the negative;
when the interior light is on, the text
is displayed in the positive.
“POSI1”: Displays the text in the positive.
“POSI2”: When the interior light is off, the text
is displayed in the positive; when
the interior light is on, the text is
displayed in the negative.
“Text Scroll”
Sets the method of scroll to view hidden text.
“Auto” : Scrolls.
“Once” : Scrolls once.
“OFF” : Does not scroll.
“BT DVC Status”
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
: Signal strength of cell-phone.
English
|
29
General operation
Adjusting the Clock
Adjusting the Date
1 Enter Function setting mode
1 Enter Function setting mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
2 Select the Clock Adjust mode
The item can be selected and determined as
follows.
2 Select the Date Adjust mode
The item can be selected and determined as
follows.
“Settings” > “Clock&Date” > “Clock Adjust”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Clock&Date” > “Date Adjust”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Set hour
3 Set year
Turn the Control knob to adjust the hour, and
then press the Control knob.
Turn the Control knob to adjust the year, and
then press the Control knob.
4 Set minute
4 Set month
Turn the Control knob to adjust the minute, and
then press the Control knob.
Turn the Control knob to adjust the month, and
then press the Control knob.
5 Exit Function setting mode
5 Set day
Press the [
] button for at least 1 second.
Turn the Control knob to adjust the day, and
then press the Control knob.
⁄
6 Exit Function setting mode
Press the [
] button for at least 1 second.
|
30 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Dual clock display
Clock & Date display type setting
Sets time for two different cities.
Sets the display type of the clock and calendar.
1 Enter Function setting mode
1 Enter Function setting mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
2 Select the City Select mode
2 Select the Clock & Date settin mode
The item can be selected and determined as
follows.
The item can be selected and determined as
follows.
“Settings” > “Clock&Date” > “City Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Clock&Date”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the clock display part
3 Select the desired Clock & Date setting item
Turn the Control knob to select Clock & Date
display setting item, and then press the Control
knob.
Push the Control knob towards up or down.
4 Set cities for Home/ Sub
Turn the Control knob.
Display
Overview
5 Determine cities for Home/ Sub
“Clock&Date”
Press the Control knob.
“Time Synchronized” Synchronizing the Radio data system station
time data and this unit’s clock.
6 Exit Function setting mode
“ON” / “OFF”
Press the [
] button for at least 1 second.
“Summer Time”
Advances the clock one hour when set to ON.
“ON” / “OFF”
⁄
“Sub Clock Adjust” Adjusts the time difference caused by summer
time.
• Time of Sub City is automatically derived from Home time.
When summer time systems are different between Home
and Sub cities, adjustment can be done by referring to
“-1h” / “0h” / “+1h”
Sets the date display mode.
7 types
“Date Mode”
(
: Factory setting)
4 Set the Clock & Date setting items
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
31
General operation
Function of KDC-X595, KDC-448U
Muting the audio upon reception of
phone call
Auxiliary input display setting
Sets the display when switched to AUX source.
1 Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
The audio system automatically mutes when a call
comes in.
When a call comes in
“CALL” is displayed.
The audio system pauses.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Name set mode
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
The item can be selected and determined as
follows.
“Settings” > “AUX Name Set”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
comes back ON.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
comes back ON.
4 Sets the display of the AUX source
Turn the Control knob to select Auxiliary input
display, and then press the Control knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
“TV”.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting wires to terminals> (page
12) of Quick start guide.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
32 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
“F/W Update #.##” Upgrades the firmware.
Selecting“YES”and then pressing Control knob
Initial setting
Configures initial settings of this unit.
starts upgrading the firmware.
For how to update the firmware, access our
web site.
1 Select Standby
Press the [SRC] button.
Select the “STANDBY” display.
(
: Factory setting)
2 Enter Function setting mode
5 Set the Initial setting item
Press the Control knob for at least 1 second.
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
3 Select the Initial setting mode
Turn the Control knob to select “Initial Settings”,
and then press the Control knob.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
4 Select the desired Initial setting item
Turn the Control knob to select Initial setting
item, and then press the Control knob.
Display
Overview
“Initial Settings”
“Source Select”
Select“2”to change the source selection
method. Press the [SRC] button, turn the
Control knob to select the source, and then
press the Control knob to determine it.
1 / 2
“Key Beep”
Setting the operation check sound (beep
sound) ON/OFF.
“ON” / “OFF”
“Function Language” Changes the display language of items in
Function setting.
“English” / “Français” / “Español”
“Built-in AUX”
“CD Read”
Sets whether to display AUX during source
selection.
“ON” / “OFF”
Sets the method for reading CD.
When unable to play special format CD, set
this function to“2”to force playing. Note that
some music CDs may be unplayable even
when set to“2”.
In addition, audio files cannot be played when
set to“2”. Normally, keep this set to“1”.
1: Automatically distinguishes between audio
file disc and music CD when playing disc.
2: Forces playing as music CD.
“Built-in AMP”
“Speaker Select”
Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“ON” / “OFF”
Fine-tuning so that the System Q value is
optimal when setting the speaker type as
follows;
“OFF”: OFF
“5/4inch”: For 5 & 4 in. speaker
“6x9/6inch”: For 6 & 6x9 in. speaker
“O.E.M.”: For the OEM speaker
English
|
33
General operation
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Demonstration mode
Turn the Control knob to select “DEMO Mode”,
and then press the Control knob.
3 Set the Demonstration mode
Turn the Control knob to select desired value
(“ON” or “OFF”), and then press the Control
knob.
Exit Function setting mode.
|
34 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
35
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Function of KDC-X895, KDC-BT848U
Before use
Registering cell-phone
KDC-X895/ KDC-BT848U
• If your cell-phone is not yet registered, register (pair)
it by referring to <Registering cell-phone> (page 8)
in the Quick Start Guide or <Registering cell-phone>
(page 36) in this document.
• To register a new cell-phone, you can also refer to
1 Enter Bluetooth mode
Press the [ ] button for at least 1 second.
If your cell-phone is not yet registered, the search
for a cell-phone starts with “Searching” displayed.
Paring with new cell-phone
Turn the Control knob to select “Device Search”,
and then press the Control knob.
The search for a cell-phone starts with “Searching”
displayed.
KDC-X595/ KDC-448U
• If your cell-phone is not yet registered, register (pair)
it by referring to <Registering cell-phone> (page 8)
in the Quick Start Guide or <Registering Bluetooth
device> (page 46) in this document.
2 Select the used cell-phone
Turn the Control knob to select cell-phone
name, and then press the Control knob.
⁄
3 Input the PIN code
Operation type
• For details on the Bluetooth cell-phone with the
hands-free function, see <About the Cell-phone>
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
Pairing completes with “HF Connect” displayed.
⁄
• When any error code is displayed while the paring is in
|
36 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Receiving a call
Calling a number in the Phone book
Answering a phone call
KDC-X895 KDC-BT848U
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [ ] button.
KDC-X595 KDC-448U
Press the Control knob.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
⁄
• The following operations disconnect the line:
- Insering a CD.
2 Select the Name search mode
Turn the Control knob to select “Phone Book”,
and then press the Control knob.
- Connecting a USB device.
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
3 Search for Phone book
Operation type
Select the Phone number.
Select the name.
Operation
Rejecting an incoming call
Turn the Control knob.
Push the Control knob towards right
or left.
Push the Control knob towards up
or down.
KDC-X895 KDC-BT848U
Press the [
] button.
KDC-X595 KDC-448U
Select the initial.
Press the [SRC] button.
Determine the Phone number. Press the Control knob.
4 Make a call
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the Control knob.
⁄
• Pressing [DISP] button each time switches between name
and telephone number.
• During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
English
|
37
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Dialing a number
Calling a number in the call log
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
Press the [ ] button.
KDC-X595 KDC-448U
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Select the Number dial mode
2 Select the call log mode
Turn the Control knob to select “Number Dial”,
and then press the Control knob.
Turn the Control knob to select “Incoming
Calls”, “Outgoing Calls”, or “Missed Calls”, and
then press the Control knob.
3 Enter a phone number
“Incoming Calls”: Incoming calls
“Outgoing Calls”: Outgoing calls
“Missed Calls”: Missed calls
Turn the Control knob to select number, and
then Push the Control knob towards right.
4 Make a call
3 Select a name or phone number
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Turn the Control knob.
4 Make a call
Press the Control knob.
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
To erase the entered phone number digit by
digit:
Push the Control knob towards left.
Press the Control knob.
⁄
⁄
• Pressing [DISP] button each time switches between name
and telephone number.
• You can input a maximum of 32 (KCA-BT300/BT200)/ 25
(KDC-X895/ KDC-BT848U) digits.
• The outgoing call list, the incoming call list, and the missed
call list, are the lists of calls originated from and received
at this unit. They are not the ones stored in the cell-phone
memory.
|
38 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Speed dialing (Preset dial)
Registering to the Preset dial number
list
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dialing a number/ Calling a number in the call log/
Calling a number in the Phone Book
Press the [ ] button.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Select the Preset dial mode
2 Enter Preset memory mode
Turn the Control knob to select “Preset Call”,
and then press the Control knob.
Press the [PRESET] button.
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“P1” – “P6”), and then press the
Control knob for at least 2 seconds.
3 Select the number you want to recall from the
memory
Turn the Control knob to select recall number
(“P1” – “P6”), and then press the Control knob.
Cancelling the Preset memory mode
4 Make a call
Press the [
] button.
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the Control knob.
⁄
• You need to register the preset dial number. Refer to
English
|
39
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
During a call
Call waiting
Disconnecting a Call
Press the [SRC] button.
Answering another incoming call with the
current call suspended
KDC-X895 KDC-BT848U
Switching to the Private mode
Press the [ ] button.
KDC-X595 KDC-448U
Push the Control knob towards right or left.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
1) Press the Control knob.
2) Turn the Control knob to select “Answer”, and
then press the Control knob.
⁄
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection. If
this happens, the source cannot be switched back to the
hands-free talk mode by operating this unit. Operate your
cell-phone to return to the hands-free talk mode.
Answering another Incoming call after
terminating the current call
Press the [SRC] button.
Continuing the Current Call
1) Press the Control knob.
2) Turn the Control knob to select “Reject”, and
then press the Control knob.
Adjusting the voice volume during a call
Turn the Control knob.
Answering the waiting call after terminating
the current call
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [SRC] button.
Switching between the current call and waiting
call
Press the Control knob.
Each pressing of this knob switches the calling
party.
|
40 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Clearing the Disconnection message
Making a voice dialing call
KDC-X895 KDC-BT848U
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [ ] button.
Press the [LOG] button for at least 1 second.
“HF Disconnect” disappears.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter voice recognize mode
Turn the Control knob to select “Voice
Recognize”, and then press the Control knob.
3 Have the unit recognize your spoken name
Press the Control knob. If you hear a beep,
speak a registered name within 2 seconds.
4 Have the unit recognize the spoken category
When you hear a beep, speak the category
within 2 seconds.
The recognized phone number (name) is displayed.
When you want to change the displayed phone
number (name), press the [DISP] button.
5 Make a call
Press the Control knob.
⁄
• If your voice cannot be recognized, a message is displayed.
Pressing the Control knob allows you to retry voice input.
• Both the name and category requires registration of a voice
tag. Refer to <Setting a voice command for category>
English
|
41
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Displays of phone number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
Information
General
“General”/
Home
Office
Mobile
Other
“Home”/
“Office”/
“Mobile”/
“Other”/
|
42 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
43
Function of KCA-BT300/BT200 (Optional Accessory)
Bluetooth audio operation
Before Use
Basic operation
• You need to register your Bluetooth audio player
before using it with this unit. For more details, see
• You need to select the Bluetooth audio player you
wish to connect. Refer to <Selecting the Bluetooth
Selecting Bluetooth audio source
Press the [SRC] button.
Select the “BT AUDIO EXT” display.
Pause and play
Press the [
] button.
Music search
Push the Control knob towards right or left.
⁄
• All or some of the operations above cannot be performed if
the Bluetooth audio player is not ready for remote control.
• Switching between Bluetooth audio sources does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
• When “2Zone” is set to “ON” and “2Zone F/R Select” is set to
cannot be selected.
|
44 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
English
|
45
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
4 Select the desired Bluetooth device
Registering Bluetooth device
Turn the Control knob to select Bluetooth
device, and then press the Control knob.
KDC-X895 KDC-BT848U
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to five Bluetooth devices to this unit.
Input the PIN code (steps 5).
KDC-X595 KDC-448U
When registering from Bluetooth devices
When “Paring Success” is displayed, PIN code input
(steps 5) is not required.
1 Turn on the this unit.
When “Pin Code NG” is displayed, press the Control
knob. Then enter the PIN code (steps 5).
2 Start registering a unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-3P1”, “KCA-BT300”, or “KCA-BT200” from the list
of connected units.
5 Input the PIN code
Operation type
Operation
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
3 Enter a PIN code
Input the PIN code registered as mentioned in
Check that registration is complete on the
Bluetooth device.
If “Pairing Success” is displayed, registration is
complete.
6 Return to the device list
4 By operating the Bluetooth device, start hands-
Press the Control knob.
free connection.
7 Exit Bluetooth mode
When registering from this unit
Press the [SRC] button.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
Press the [ ] button.
KDC-X595 KDC-448U
• If there are 5 Bluetooth devices registered, you cannot
register a new Bluetooth device.
• If the error message appears even though the PIN code is
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth device registration mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Device Registration”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
|
46 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Registering Special bluetooth device
Registering PIN Code
Allow registration of a special device that cannot be
registered normally (pairing).
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
Press the [ ] button.
KDC-X595 KDC-448U
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
2 Enter Function setting mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
3 Select Special device registration mode
The item can be selected and determined as
follows.
3 Select PIN code edit mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “SPCL Device Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Detailed Settings” >
“PIN Code Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select a desired device name
Turn the Control knob to select device name,
and then press the Control knob.
If “Completed” is displayed, registration is
completed.
4 Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
Bluetooth device> (page 46) and complete the
registration (pairing).
If “Completed” is displayed, registration is complete.
5 Exit Bluetooth mode
Cancelling Bluetooth mode
Press the [SRC] button.
Press the [SRC] button.
⁄
⁄
• By default, “0000” is specified.
• If the device name is not in the list, select “Other Phones”.
• A PIN code can be specified with up to eight digits.
English
|
47
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
Downloading the Phone book
Selecting the Bluetooth device you
wish to connect
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
Downloading automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after the
“Completed” is displayed, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth device selection mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Phone Selection” (to
select the cell-phone) or “Audio Selection” (to
select the audio player)
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“(name)” is displayed.
Downloading from the cell-phone manually
1 Operate the cell-phone to end the hands-free
connection.
2 Operate the cell-phone to send the phone
book data to this unit
By operating the cell-phone, download the phone
book data to this unit.
• During downloading:
“Downloading” is displayed.
• After completion of downloading:
“Completed” is displayed.
4 Select a desired Bluetooth device
Turn the Control knob to select Bluetooth
device name, and then press the Control knob.
‘✱(name)’ or ‘-(name)’ is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
3 Operate the cell-phone to start the hands-free
connection.
Clearing the downloading completion message
Press any button.
5 Exit Bluetooth mode
Press the [SRC] button.
⁄
⁄
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
• If a cell-phone is already selected, deselect it, and then
select a different one.
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type of
characters.)
• If you cannot select a device using the audio player,
connect the device with the audio player.
• To cancel downloading of the phone book data, operate
the cell-phone.
|
48 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Deleting a registered Bluetooth
device
Displaying the firmware version
Display the version of the firmware of this unit.
You can delete a registered Bluetooth device.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [ ] button.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth firmware update mode
The item can be selected and determined as
follows.
“Settings” > “Detailed Settings” >
“BT F/W Update”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
The firmware version appears.
3 Select Bluetooth device deletion mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Device Delete”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Device name is displayed.
4 Exit Bluetooth mode
4 Delete the selected Bluetooth device
Turn the Control knob to select device name,
and then press the Control knob.
Press the [SRC] button.
⁄
• For how to update the firmware, access our web site.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
6 Exit Bluetooth mode
Press the [SRC] button.
⁄
• When a registered cell-phone is deleted, its Phone Book,
log, SMS, and voice tag are also deleted.
English
|
49
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
Pressing the Control knob allows you to retry voice input.
Adding a voice dialing command
Selecting “Check” (Play)
Add a voice tag to the phonebook for voice dialing.
You can register up to 35 voice tags.
6 Press the Control knob.
Play the registered voice and return to step 2.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Selecting “Delete” (Delete)
Press the [ ] button.
KDC-X595 KDC-448U
6 Delete a voice tag
Press the Control knob.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
7 Turn the Control knob to select “YES”, and then
press the Control knob.
2 Enter Function setting mode
Exit Bluetooth mode
Press the [SRC] button.
Press the Control knob for at least 1 second.
3 Select Phonebook name edit mode
The item can be selected and determined as
follows.
“Settings” > “Voice Tag” > “PB Name Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Search for the name to register
Turn the Control knob to select name, and then
press the Control knob.
If a voice tag has already been registered for a
name, “*” is displayed before the name.
5 Select a mode
Turn the Control knob.
Display
Operation
“Register”
“Check”*
“Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
*Displayed only when a name for which a voice tag has
been registered is selected.
Selecting “Register” (Regist)
6 Register a voice tag (first)
Press the Control knob. When you hear a beep,
speak the voice tag within 2 seconds.
7 Confirm the voice tag (second)
Press the Control knob. When you hear a
beep, speak the same voice tag again within 2
seconds.
“Completed” is displayed.
8 Exit Function setting mode
Press the [
] button for at least 1 second.
Return to step 2. You can register another voice tag
continuously.
⁄
• If your voice cannot be recognized, a message is displayed.
|
50 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Setting a voice command for category
Add a voice tag to the phone number category
(type) for voice calling.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Phonebook type edit mode
The item can be selected and determined as
follows.
“Settings” > “Voice Tag” > “PN Type Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select the category (type) you wish to set
Turn the Control knob to select category name,
and then press the Control knob.
“General”/ “Home”/ “Office”/ “Mobile”/ “Other”
5 Select a mode
Turn the Control knob.
Display
Operation
“Register”
“Check”*
“Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
*KCA-BT300/BT200 only. Displayed only when a name for
which a voice tag has been registered is selected.
6 Register the category (type) by performing
steps 6 to 7 in <Adding a voice dialing
7 Exit Bluetooth mode
Press the [SRC] button.
⁄
• Set the voice tag for all the 5 categories. If the voice tag is
not registered for all the categories, the Phonebook may
not be recalled by voice command.
English
|
51
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
“MIC Gain”
“NR Level”
Adjusts the sensitivity of the built-in
Bluetooth detail setting
microphone for a telephone call. Adjust the
voice of caller. Setting to“+”increases the
voice volume.
Function of the KDC-X895, KDC-BT848U
“-3” – ”0” – “+3”
SReduces the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to“+”increases
the noise reduction.
Configures initial settings of this unit.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Function of the KDC-X895, KDC-BT848U
“-3” – ”0” – “+3”
Sets the echo cancellation level.
Function of the KDC-X895, KDC-BT848U
“-2” – ”0” – “+2”
2 Enter Function setting mode
Press the Control knob for at least 1 second.
“Echo Cancel”
3 Select Bluetooth detail setting mode
The item can be selected and determined as
follows.
(
: Factory setting)
“Settings” > “Detailed Settings”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
5 Set the Bluetooth detail setting item
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
4 Select the desired Bluetooth detail setting
item
Turn the Control knob to select Bluetooth detail
6 Exit Function setting mode
Press the [
] button for at least 1 second.
setting item, and then press the Control knob.
Display
Overview
“Detailed Settings”
“Auto Answer”
This function automatically answers (responds
to) a call after lapse of the preset time interval
for automatic answer.
“OFF”: Does not answer the phone call
automatically.
“0”: Automatically answers the phone call
at once.
“1SEC” – “8SEC” – “99SEC”:
Automatically answers the phone call after
lapse of 1 – 99 seconds.
“Auto Reconnect” When“ON”is selected, re-pairing with the
registered Bluetooth device starts automatically
when pairing is disconnected.
“ON” / “OFF”
“Bluetooth HF”
“Bluetooth HF/
Audio”
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front” : Outputs sound from the front
speakers.
“All” : Outputs sound from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON” : Beep is heard.
“OFF” : Beep is canceled.
|
52 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Function of KDC-X895, KDC-BT848U, KCA-BT300/BT200 (Optional Accessory)
SMS (Short Message Service)
Displaying the SMS
Downloading the SMS
The SMS received by at the cell-phone is displayed
on the receiver.
Download the short message (SMS) received by the
cell-phone so that it can be read on this unit.
A newly received message is displayed.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
¤
• To prevent car accidents, the driver should not read the
Press the [ ] button.
KDC-X595 KDC-448U
SMS while driving.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
Displaying the SMS
3 Select SMS download mode
The item can be selected and determined as
follows.
1 Enter Bluetooth mode
KDC-X895 KDC-BT848U
Press the [ ] button.
KDC-X595 KDC-448U
“Settings” > “SMS Download”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
4 Start downloading
2 Select SMS inbox display mode
Turn the Control knob to select “SMS Inbox”,
and then press the Control knob.
Press the Control knob.
“SMS Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
3 Select a message
Turn the Control knob.
5 Exit Bluetooth mode
Each press of the [DISP] button switches between
displaying the telephone number or name and
message reception date.
Press the [SRC] button.
⁄
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required. If
the cell-phone does not support SMS function, the SMS
download item in Function Control mode is not displayed.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The up to 75 already-read and unread short messages
respectively can be downloaded.
4 Display the text
Press the Control knob.
Turn the Control knob to scroll through the
message.
Press the Control knob to return to the message
list screen.
5 Exit Bluetooth mode
Press the [SRC] button.
⁄
• The unopened message is displayed at the beginning of the
list. Other messages are displayed in the order of reception.
• The SMS that are received when the cell-phone is not linked
with Bluetooth cannot be displayed. Download the SMS.
• The short message cannot be displayed during
downloading the SMS.
English
|
53
Function of KTC-HR300, KTC-HR200, KTC-HR100 (Optional Accessory)
HD Radio™ tuner control
Basic Operation
Station preset memory
Putting a station in the memory.
Selecting HD Radio source
Press the [SRC] button.
Select the “HD RADIO” display.
1 Select the frequency to put in the memory
Push the Control knob towards right or left.
Selecting the band
2 Enter Preset memory mode
Press the [PRESET] button.
“Preset List” is displayed.
Push the Control knob towards down.
Switches between the FM1, FM2, FM3, and AM
bands each time you push towards down.
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“1” – “6”), and then press the Control
knob for at least 2 seconds.
Selecting the station
Push the Control knob leftward and rightward.
⁄
Cancelling the Preset memory mode
• During reception of stereo stations the “ST” indicator lights
Press the [
] button.
⁄
up.
• If you press the [PRESET] button twice in step 2, Mix Station
preset mode is entered with “Mixed Preset List” displayed.
In this mode, different bands and tuner sources (Radio,
Sirius, XM etc.) can be saved in the same preset layer, which
allows you to recall the desired station without switching
the bands or tuner sources.
Maximum of six stations can be preset in the Mix Station
preset mode.
Once the Mix Station preset mode is set, you can enter the
same mode by just pressing the [PRESET] button once in
step 2.
Pressing the [PRESET] button twice returns to the normal
Station preset mode.
|
54 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Preset tuning
Auto memory
Recalling the stations in the memory.
Memorizes six stations with good reception
automatically.
1 Enter Preset memory mode
Press the [PRESET] button.
“Preset List” is displayed.
1 Select Tuner source
Press the [SRC] button.
Select the “HD RADIO” display.
2 Select the number you want to recall from the
memory
Turn the Control knob to select recall number
2 Enter Function setting mode
Press the Control knob for at least 1 second.
(“1” – “6”), and then press the Control knob.
3 Select the Auto memory mode
The item can be selected and determined as
follows.
Cancelling Preset tuning
Press the [
] button.
“Settings” > “Auto Memory”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Start Auto memory mode
Turn the Control knob to select “YES”, and then
press the Control knob.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
English
|
55
Function of KTC-HR300, KTC-HR200, KTC-HR100 (Optional Accessory)
HD Radio™ tuner control
Function of KTC-HR300
Seek mode setting
iTunes tagging
Selects the tuning mode of the radio.
By using an iTunes Tagging enabled HD Radio you
can tag your music. When you hear a song you
enjoy on your local HD Radio station, you only have
to press the Control knob. The song’s information
will then be saved on this unit. The saved songs
will then show up in a playlist called “Tagged” in
iTunes the very next time you sync your iPod to
your computer. Then you just need to click and
then easily buy and download the song you were
tagging directly from the Apple iTunes Music Store.
1 Select Tuner source
Press the [SRC] button.
Select the “HD RADIO” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Seek mode
The item can be selected and determined as
follows.
“Settings” > “Seek Mode”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
1 Enter HD Radio iTunes tagging mode
Press the [PRESET] button for at least 1 second.
“
” will be indicated on the display when song
TAG
4 Set the desired Seek mode
information can be registered.
Tuning mode
Display Operation
“TAG Storing” is indicated on the display while a tag
is being stored to this unit. “TAG Stored” is indicated
on the display after a tag is stored.
“TAG Transferred” is indicated on the display after a
tag is stored to your iPod.
Auto seek
“Auto1” Automatic search for a station.
Preset station seek “Auto2” Search in order of the stations in the
Preset memory.
Manual
“Manual” Normal manual tuning control.
Turn the Control knob to select Seek mode, and
then press the Control knob.
⁄
when using this function.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
• Up to 50 TAGs (song’s information) can be registered to
this unit. When iPod is connected, the TAG information
registered to this unit is transferred to the connected iPod.
|
56 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Function of KTC-HR300 with remote control
HD Radio setting
Direct access tuning
Sets the HR Radio-related items.
Entering the frequency and tuning.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Enter Direct access tuning mode
Press the [DIRECT] button on the remote
control.
2 Select the Setting mode
Turn the Control knob to select “Settings”, and
then press the Control knob.
“– – – –” is displayed.
2 Select Tuning item
3 Select the desired HD Radio setting item
Turn the Control knob to select HD Radio
setting item, and then press the Control knob.
Press the [DIRECT] button on the remote
control.
Pressing the [DIRECT] button each time switches
the following tuning items as follows.
Display
Overview
“Settings”
Tuning item
Frequency
Channel
Cancelling Direct Access Tuning
Display
“– – – –”
“HD –”
—
“Receive mode”
Sets the receive mode of the HD Radio.
Auto: Automatically tunes to analog broadcast
when there is no digital broadcast.
Digital: Digital broadcasts only.
Analog: Analog broadcasts only.
“TAG Memory”
“Tagging”
Displays the tag memory usage of HD Radio.
Up to 50 tags can be registered to this unit.
Function of the KTC-HR300
Turns ON / OFF the iTunes tag memory
function of HD Radio.
3 Enter the frequency or channel
Press the number buttons on the remote
control.
Example of frequency input:
Function of the KTC-HR300
“ON” / “OFF”
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[9], [2], [1]
[8], [1], [0]
(
: Factory setting)
4 Set the HD Radio setting item
4 Do Direct access tuning
Press the [4] or [¢] button on the remote
control.
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
Cancelling Direct access tuning
5 Exit Function setting mode
Press the [
] button on the remote control.
Press the [
] button for at least 1 second.
English
|
57
Satellite radio tuner (Optional accessory) control
Basic operation
Category and Channel search
Selecting the channel and category you want to
receive.
Selecting Satellite Radio source
Press the [SRC] button.
Select the “SIRIUS” or “XM” display.
1 Enter Category and Channel search mode
Press the [ ] button twice.
⁄
• You need to register to the service provider to receive the
service by Satellite Radio. Consult the service provider if
“CALL … TO SUBSCRIBE” appears.
2 Select the Category
Turn the Control knob to select Category, and
then press the Control knob.
• The radio may take a little time to start receiving after you
select the Satellite Radio source.
• If the signal reception fails, “Acquiring Signal”/ “No Signal”
appears.
3 Select the Channel
Turn the Control knob to select Channel, and
then press the Control knob.
Selecting the channel
Push the Control knob towards right or left.
Cancelling Category and Channel search mode
Press the [
] button for at least 1 second.
Selecting the preset band
⁄
Push the Control knob towards down.
Each time you push the knob, the preset band
alternates between the SR1, SR2, SR3 and SR4.
• You cannot Channel search until the category information
is acquired.
|
58 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Channel preset memory
Preset tuning
Putting the channel in the memory.
Recalling the channels in the memory.
1 Select the channel to put in the memory
1 Enter Preset memory mode
Push the Control knob towards right or left.
Press the [PRESET] button.
2 Enter Preset memory mode
2 Select the number you want to recall from the
memory
Press the [PRESET] button.
Turn the Control knob to select recall number,
and then press the Control knob.
3 Select a number and store it in the memory
Turn the Control knob to select memory
number, and then press the Control knob for at
least 2 seconds.
Cancelling Preset tuning
Press the [
] button.
Cancelling the Preset memory mode
Press the [
] button.
⁄
• Only the channel number is stored. Category information
is not stored.
• If you press the [PRESET] button twice in step 2, Mix Station
preset mode is entered with “Mixed Preset List” displayed.
In this mode, different bands and tuner sources (Radio,
Sirius, XM etc.) can be saved in the same preset layer, which
allows you to recall the desired station without switching
the bands or tuner sources.
Maximum of six stations can be preset in the Mix Station
preset mode.
Once the Mix Station preset mode is set, you can enter the
same mode by just pressing the [PRESET] button once in
step 2.
Pressing the [PRESET] button twice returns to the normal
Station preset mode.
English
|
59
Satellite radio tuner (Optional accessory) control
Function of remote control
Channel scan
Direct access tuning
Every receivable Channel is checked for 10 seconds.
Entering the channel and tuning.
1 Start Channel Scan
Press the [ ] button for at least 1 second.
1 Enter Direct access tuning mode
Press the [DIRECT] button on the remote
control.
2 Release it when the channel you want to listen
to is received
Press the [ ] button for at least 1 second.
2 Enter the channel
Press the number buttons on the remote
control.
3 Search the channel
Press the [4] or [¢] button on the remote
control.
Cancelling Direct access tuning
Press the [
] button on the remote control.
⁄
• If you make no button operation for 10 seconds, the Direct
Access Tuning mode is automatically canceled.
• If you cannot receive any signal in the input Channel due
to bad conditions on radio wave or other such problems,
“Acquiring Signal” appears.
|
60 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Seek mode setting
Electronic serial number display
Selects the tuning mode of the radio.
Displays the Electronic Serial Number of satellite
radio.
1 Select Tuner source
Press the [SRC] button.
1 Select Tuner source
Select the “SIRIUS” or “XM” display.
Press the [SRC] button.
Select the “SIRIUS” or “XM” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Seek mode
The item can be selected and determined as
follows.
3 Select the Electronic serial number display
mode
“Settings” > “Seek Mode”
The item can be selected and determined as
To select the item, turn the Control knob. To
determine the item, press the Control knob.
follows.
“Settings” > “ESN Watch”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
The Electronic serial number is displayed.
4 Select the desired Seek mode
Display
Operation
“Channel” Normal manual seeking control.
4 Exit Function setting mode
”Preset”
Search in order of the channels in the Preset memory.
Press the [
] button for at least 1 second.
Turn the Control knob to select Seek mode, and
then press the Control knob.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
61
Basic operations of remote control
General control
VOL
• Volume control: [VOL]
SRC
• Source selection: [SRC]
• Volume reduction: [ATT]
When the button is pressed again, the volume returns to
the previous level.
ATT
ENT
5/∞
• Return to previous item: [
• Exit from mode: [EXIT]
• Selection of item: [5]/[∞]
• Determination: [ENT]
]
EXIT
AM
AUD
FM
0 — 9
• Enter Audio Control mode: [AUD]
In Tuner source
DIRECT
• Band selection: [FM]/[AM]
• Station selection: [4]/[¢]
• Recall preset stations: [0] – [9] ➜ [ENT]
Preparing the remote control unit
HD Radio source
Pull the battery sheet out from the
remote control unit to the direction of
the arrow.
• Band selection: [FM]/[AM]
• Station selection: [4]/[¢]
• Recall preset stations: [1] — [6]
Changing the battery of the remote control
unit
In CD/Audio file source
Use a commercially available
button battery (CR2025).
Insert the battery with the +
and – poles aligned properly,
following the illustration
inside the case.
Keep on slide
• Music selection: [4]/[¢]
• Folder selection: [FM]/[AM]
• Pause/Play: [ENT]
CR2025
(+side)
• Enter Music search mode: [5]/[∞]
• Movement between folders/files during Music
search mode: [5]/[∞]
Pull out
• Return to previous folder: [
]
In iPod source
• Enter Music search mode: [5]/[∞]
• Movement between items during Music search
mode: [5]/[∞]
• Return to previous item: [
]
|
62 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
In Satellite radio tuner source
¤ CAUTION
• Band selection: [FM]
• Channel selection: [4]/[¢]
• Recall preset channels: [1] — [6]
• Keep battery out of reach of children and in original
package until ready to use. Dispose of used batteries
promptly. If swallowed contact physician immediately.
• Do not leave the battery near fire or under direct
sunlight. A fire, explosion or excessive heat generation
may result.
Hands-free phone control
• Do not set the remote control in hot places such as on
the dashboard.
Making a call
• Enter Bluetooth mode: [
• Select a dialing method: [5]/[∞] ➜ [ENT]
• Number dial input:
]
• Danger of explosion if Lithium battery is incorrectly
replaced. Replace only with the same or equivalent type.
Input a digit: [0] – [9]
Input “+”: [¢]
Input “#”: [FM]
Input “*”: [AM]
Clear the entered phone number: [4]
• Make a call: [DIRECT]
Receiving a call
• Answer the call: [
]
Call waiting
• Answer Another Incoming Call with the Current
Call Suspended: [
]
During a call
• End the call: [SRC]
English
|
63
Appendix
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
• Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 4 m can result in abnormal playback.
About Audio file
•
•
•
•
•
Playable Audio file
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class
iPod/iPhone that can be connected to this
Playable USB device file system
FAT16, FAT32
unit
Made for
Even if the audio files comply with the standards listed
above, the play may be impossible depending on the
types or conditions of media or device.
• iPod nano (6th generation) • iPod nano (5th generation)
• iPod nano (4th generation) • iPod nano (3rd generation)
• iPod nano (2nd generation) • iPod nano (1st generation)
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
• iPod with video
• iPod classic
• iPod touch (4th generation) • iPod touch (3rd generation)
• iPod touch (2nd generation) • iPod touch (1st generation)
^
¡
: Folder
Folder
CD
(1)
• iPhone 4
• iPhone 3G
• iPhone 3GS
• iPhone
:
A
udiofile
¡!
2
• For information on the compatibility of iPod/iPhone
• Type of control available varies depending
on the type of connected iPod. See
www.kenwood.com/cs/ce/ipod/ for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
3
¡"
¡#
4
¡$
5
¡%
¡P
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
* Not supported model KCA-iP500.
• Refer to the web site for connectable iPod and iPod
connection cable.
⁄
⁄
• If you start playback after connecting the iPod, the music
that was playing on the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
• You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
About USB device
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Save backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
|
64 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Function of KDC-X895, KDC-BT848U
About the Cell-phone
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Light ver1.1” or later.
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Light ver1.1”, you can search a file by title, album or
This unit conforms to the following Bluetooth
specifications:
Version
Profile
Bluetooth Standard Ver. 2.1+EDR
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phonebook Access Profile)
SYNC (Synchronization Profile)
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
• “KENWOOD Music Editor Light ver1.1” is available
from the following web site:
For the cell-phones verified for compatibility, access
the following URL:
⁄
• For further information on “KENWOOD Music
Editor Light ver1.1”, refer to the site above or the
application help.
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
• HFP is a profile used to make a hands-free call.
• OPP is a profile used to transfer data such as a phone book
between units.
About Satellite radio tuner (Optional)
This unit supports Satellite Radio tuners which are
released by SIRIUS and XM.
Refer to the instruction manual of Satellite radio tuner.
About HD Radio reception (Optional)
When you connect an HD Radio tuner, Tuner features
of the unit are disabled and changed to HD Radio
tuner features.
With the HD Radio tuner, you can use the similar
functions of Tuner features. Refer to Tuner features for
how to use the functions.
English
|
65
Troubleshooting guide
Some functions of this unit may be disabled by
some settings made on this unit.
The messages shown below display your
systems condition.
TOC Error:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
!
!
• Cannot set up Display.
<Demonstration mode Setting> (page 34) is not set to
Off.
Error 05:
Error 77:
The disc is unreadable.
• Cannot set up “Text Select”, “Side Select”, and
“Status” of “Display Select”.
<Selecting display type> (page 26) is set to Displays
off.
The unit is malfunctioning for some reason.
Press the reset button on the unit. If the
“Error 77” code does not disappear, consult
your nearest service center.
!
!
• Cannot set up the subwoofer.
• Cannot set up the low pass filter.
• No output from the subwoofer.
On.
Mecha Error: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
the reset button on the unit. If the “Mecha
Error” code does not disappear, consult
your nearest service center.
Cannot set up the subwoofer Phase.
“Through”.
IN (Blink):
The CD player section is not operating
properly.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
Protect (Blink): The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
General
? The Key beep does not sound
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
The preout jack is being used.
The Key beep cannot be output from the preout
jack.
NA File:
An Audio file is played with a format that this
unit can’t support.
Tuner source
? Radio reception is poor.
Copy PRO:
Read Error:
A copy-protected file is played.
The car antenna is not extended.
Pull the antenna out all the way.
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
Disc source
? The specified disc does not play, but another one
plays instead.
The specified CD is quite dirty.
Clean the CD, referring to the CD cleaning of the
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
The disc is severely scratched.
Try another disc instead.
Audio file source
• An unsupported USB device is connected.
• Connection to the iPod has failed.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 64) for information on supported
iPods.
? The sound skips when an Audio file is being
played.
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
The recording condition is bad.
Record the media again or use another media.
|
66 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
No Music Data/Error 15:
• The connected USB device contains no
Too Long:
The word or utterance is too long to be
recognized.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
USB ERROR:
iPod Error:
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Record:
The voice tag is not registered in the
phonebook.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Confirm that the software for the iPod is
the latest version.
LOG: No Memory:
The procedure is not registered to Log Preset
Memory.
No Access:
The procedure preset with Log Preset
Memory cannot be available. The preset
content may not be recalled depending on
the selected source or mode.
Reset iPod/ iPhone.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Voice:
No call.
Memory Full: The tag memory of HD Radio is FULL.
iPod Full: The iPod memory is FULL.
No TAG Function:
No Entry:
The cell-phone has not been registered
(pairing).
iPod which does not support the tag memory
is connected.
HF Disconnect: The unit cannot communicate with the cell-
phone.
N/A Channels: No receivable channel and category.
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Unknown:
The Bluetooth device cannot be detected.
Device Full:
5 Bluetooth device have already been
registered. No more Bluetooth devices are
registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
Too Loud:
English
|
67
Specifications
FM tuner section
USB interface
Frequency range (200 kHz step)
: 87.9 MHz – 107.9 MHz
USB Standard
: USB1.1/ 2.0 (Full speed)
Usable sensitivity (S/N = 26dB)
: 11.2dBf (1 μV/75 Ω)
File System
: FAT16/ 32
Quieting Sensitivity (S/N = 50dB)
: 19.2dBf (2.5 μV/75 Ω)
Maximum Supply current
: 500 mA
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
Signal to Noise ratio (MONO)
: 63 dB
WMA decode
: Compliant with Windows Media Audio
Stereo separation (1 kHz)
: 40 dB
AAC decode
: AAC-LC “.m4a” files
AM tuner section
Audio section
Frequency range (10 kHz step)
: 530 kHz – 1700 kHz
Maximum output power
: 50 W x 4
Usable sensitivity (S/N = 20dB)
: 31 dBµ (36 µV)
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed (Audio files)
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
KDC-X895/ KDC-X595 : 0.008 %
KDC-BT848U/ KDC-448U : 0.010 %
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 12.5 kHz 8 dB
Preout level / Load (CD)
KDC-X895/ KDC-X595 : 4000 mV/10 kΩ
KDC-BT848U/ KDC-448U : 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Bluetooth section (KDC-X895/ KDC-BT848U)
Version
: Bluetooth Ver. 2.0 Certified
Frequency range
: 2.402 – 2.480 GHz
Signal to Noise ratio (1 kHz)
KDC-X895/ KDC-X595 : 110 dB
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
KDC-BT848U/ KDC-448U : 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
Maximum Communication range
: Line of sight approx.10m (32.8 ft)
Profiles
: HFP (Hands Free Profile)
: HSP (Headset Profile)
WMA decode
: SPP (Serial Port Profile)
: Compliant with Windows Media Audio
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
AAC decode
: AAC-LC “.m4a” files
|
68 KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U
Auxiliary input
Frequency response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage
KDC-X895/ KDC-BT848U
: 14.4 V (10.5 – 16V allowable)
KDC-X595/ KDC-448U
: 14.4 V (11 – 16V allowable)
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 160 mm
7-3/16 x 2-1/16 x 6-5/16 inch
Weight
: 2.9 lbs (1.3 kg)
Specifications subject to change without notice.
English
|
69
IC (Industry Canada) Notice
2CAUTION
Operation is subject to the following two conditions:
(1)This device may not cause interference, and
(2)this device must accept any interference, including
interference that may cause undesired operation of
the device.
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following
are reproductions of labels on, or inside the product
relating to laser product safety.
The term “IC: ” before the certification/ registration
number only signifies that the Industry Canada
technical specification were met.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
• Contains Transmitter Module
FCC ID : RKXCK5000NVIA
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
• Contains Transmitter Module
IC: 5119A-CK5000NVIA
Location : Top plate
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
CALIFORNIA, USA
This product contains a CR Coin Cell Lithium Battery which
contains
Perchlorate Material – special handling may apply.
FCC NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment may cause harmful interference to radio
communications, if it is not installed and used in
accordance with the instructions. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
This symbol mark indicates that Kenwood
manufactured this product so as to
decrease harmful influence on the
environment.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
• The “AAC” logo is a trademark of Dolby Laboratories.
• iTunes is a trademark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety
and regulatory standards. Please note that the use of
this accessory with iPod or iPhone may affect wireless
performance.
• Consult the dealer or an experienced radio/TV
technician for help.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S. and
other countries.
• Ready to receive HD Radio™ broadcasts when
connected to the KTC-HR300/ KTC-HR200/ KTC-HR100,
sold separately.
|