DVD/VCD/CD PLAYER
DVF-3500
INSTRUCTION MANUAL
Declaration of Conformity with regard to the EMC Directive
2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
DIGITAL
© B60-5767-08/00 (E, X)
IMPORTANT SAFETY INSTRUCTIONS
Caution: Read this page carefully to ensure safe operation.
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions should
be retained for future reference.
12.Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
Heed Warnings – All warnings on the product and in the operating
instructions should be adhered to.
Follow Instructions – All operating and use instructions should be
followed.
13.Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions.
1. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
2. Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
3. Water and Moisture – This product shall not be exposed to
dripping and splashing – for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement; or near a
swimming pool; and the like. Do not place an object containing
liquid, such as a flower vase, on the appliance.
g) If an abnormal smell or smoke is detected.
14.Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or
other hazards.
4. Accessories – Do not place this product on an
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child
or adult, and serious damage to the product.
15.Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer. Any mounting of
the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer. A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
16.Wall or Ceiling Mounting – This product should be mounted
to a wall or ceiling only as recommended by the manufacturer.
17.Heat – This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products that
produce heat. Do not place a flaming object, such as a candle
or lantern, or near the product.
5. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and
to protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
18.Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
6. Power Sources – This product should be operated only from the
type of power source indicated on the product. If you are not sure of
the type of power supply to your home, consult your product dealer
or local power company.
19.Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
CAUTION– Polarization –
7.
This product may be equipped
with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
8. Power Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the product.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIR
E
GROUND CLAMPS
9. Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
10.Overloading – Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk of
fire or electric shock.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
11.Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
Notes:
1. Item 7 is not required except for grounded or polarized
equipment.
2. Item 19 complies with UL in the U.S.A.
English
3
Before applying power
Accessories
Check that all accessories are present in the package.
Audio cord (Red, White) Video cord (Yellow)
Coaxial cable (Black)
(x 1)
Remote control unit
(RC-D0314 x 1)
Remote control batteries
(R03 x 2)
(x 1)
(x 1)
If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer immediately. If the unit was shipped to you
directly, notify your shipper immediately. Kenwood recommends that you retain the original carton and packing materials in case you
need to move or ship the unit in the future.
Keep this manual handy for future reference.
DVF-3500
4
Special features
• Higher video quality than S-VHS video and LaserDisc
• Higher audio quality than music CD
• Graphical User Interface (G.U.I.)
®
• MPEG1 , MPEG2 files, DivX video playback
• MP3, WMA and JPEG files playback
This document classifies the applications of each feature using the following marks.
: Description of a feature that can be used with audio CD (CD-DA).
: Description of a feature that can be used with DVD video.
: Description of a feature that can be used with VCD.
: Description of a feature that can be used with DivX®video.
: Description of a feature that can be used with JPEG.
: Description of a feature that can be used with MP3.
: Description of a feature that can be used with WMA.
Contents
To ensure safety, read the items carrying this marking carefully.
Before applying power................................... 2
IMPORTANT SAFETY INSTRUCTIONS ............ 3
Accessories................................................................................4
Special features .......................................................................5
Contents.....................................................................................5
Operations
Basic playback of disc ........................................ 22
On screen display................................................................. 22
Last Scene Memory............................................................. 22
Basic play................................................................................. 23
Disc playback features ....................................................... 24
Repeat play.............................................................................................. 24
A-B Repeat play .................................................................... 25
Program play ......................................................................... 25
Disc information................................................... 6
Types of playable discs .........................................................6
Unplayable discs .....................................................................6
Region codes ........................................................ 7
Region codes in the world...................................................7
Icons on the DVD VIDEO discs............................................7
Playable files with this unit ................................. 8
File Specifications...................................................................8
Creating media for playing back on this equipment...8
Video formats ....................................................... 9
For your information.......................................... 10
Movie disc playback........................................... 26
..................................................... 27
Select Audio Language
Select the Audio channel
.................................................. 27
.......................................................................... 27
Using Marker
........................................................... 28
Select Camera angle
Select Subtitle Language
.................................................... 28
...................................................................... 28
Zoom function
Time Search
............................................................................ 29
Music disc playback ........................................... 30
Preparation
.......................... 30
Using the TV screen to start playback
............................................. 30
To display the ID3 tag
.......................................................................... 30
Connections........................................................ 11
Playback from desired track
......................................................... 30
Controls and indicators ..................................... 14
Main unit................................................................................. 14
Remote control unit............................................................ 14
Random play
Photo files playback (JPEG files only)............... 31
.................................................................. 31
To start playback
Zoom function
Set Up functions ................................................. 16
When you turn on for the first time.............................. 16
Set up menu........................................................................... 16
LANGUAGE ..............................................................................17
DISPLAY ....................................................................................17
AUDIO........................................................................................17
LOCK (Parental Control)..................................................... 18
OTHERS.....................................................................................19
...................................................................... 31
................................................................... 31
To rotate picture
To hide the menu bar
......................................................... 31
............................................................................... 31
Slide show
Knowledge
Troubleshooting................................................. 32
Specifications ..................................................... 34
Hierarchical structure of VCD menus (P.B.C. function)
.................................................................................................... 20
DVD menu language code list ........................................ 21
Area Code code list ............................................................. 21
English
5
Disc information
Types of playable discs
The system this unit is using does not only play music from CD but can also play the discs listed below to offer you high-quality enter-
tainment of video of movies and live concerts.
DVD VIDEO
(DVD-R/RW, DVD+R/RW)
Playable Disc
CD (CD-R, CD-RW)
VCD (SVCD*)
Logo mark
on disc
Disc size
8 cm
One or both
12 cm
One or both
8 cm
One side only
12 cm
One side only
8 cm
One side only
12 cm
One side only
Played sides
Approx. 41 min.
(1 side, 1 layer)
Approx. 75 min.
(1 side, 2 layers)
Approx. 82 min.
(2 sides, 1 layer)
Approx. 150 min.
(2 sides, 2 layers)
Approx. 133 min.
(1 side, 1 layer)
Max. 20 min.
Max. 74 min.
Approx. 242 min.
(1 side, 2 layers)
Approx. 266 min.
(2 sides, 1 layer)
Approx. 484 min.
(2 sides, 2 layers)
Video +
Audio
(In case of an SVCD, the possible play-
back time becomes shorter.)
Audio
Max. 20 min., digital Max. 80 min., digital
Please refer to page 8 for the CD-R, CD-RW, DVD-R, and DVD-RW file formats which can be played back by this unit.
• * This unit can play SVCDs, but some functions will not work.
•
A Dual Disc is a two-sided disc combining a DVD side according to the DVD standard and a music side. The video content recorded on the
DVD side can be played back. As the music side is not compatible with the Compact Disc (CD) standard, playback on this unit is not assured.
This unit can play back DVD-R and DVD-RW discs recorded in the DVD VIDEO format and DVD+R and DVD+RW discs, but depending on the
recording unit, the disc manufacturer, etc., playback sometimes may not be possible.
•
•
•
This unit may also be incapable of playing certain CD-R/RW discs depending on their properties, recording conditions, etc.
This player cannot play back discs compatible with CPRM. CPRM is the abbreviation of Content Protection for Recordable Media, and it is a
technique for copyright protection for recording media.
Unplayable discs
This player cannot play back any of the following discs.
•
•
A DVD video disc with a region code which does not match this
unit or without a region code. For details, see "Region codes". (See
page 7.)
When the video format of a disc differs from that of the TV in
use, the disc cannot be played normally. For details, see "Video
Formats". (See page 9.)
DVD AUDIO discs
DVD-RAM discs
SACD discs
VSD discs
CDV discs (Only the audio part can be reproduced.)
CD-G/CD-EG/CD-EXTRA discs (Only the audio can be repro-
duced.)
Restriiccttiioonnss dduuee ttoo ddiiffffeerreennccee bbeettwweeeenn ddiissccss
Inhibition icon
Some DVD and VCD discs can be played only in certain playback modes according to the intentions of the software
producers. Depending on the condition of this unit, operation may be restricted. As this player plays discs accord-
ing to their intentions, some functions may not work as intended by you. Please be sure to read the instructions
provided with each disc. When an inhibition icon is displayed on the TV screen connected to the player, it indicates
that the disc being played is under the restriction as described above.
DVF-3500
6
Region codes
Every player of this model has a certain region code assigned to it based on the country where the player is used. When the player is
used to play back DVD VIDEO discs, it can only play the DVD VIDEO discs carrying the region codes matching the region code of the
player.
The region code for this player is described on the rear panel of the player.
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the following map.
Professional use disc
(Air Line cabin service)
Reggioonn ccooddeess ooff tthhee DDVVDD VVIIDDEEOO ddiissccs thaatt ccaann bbee plaayyeedd wwiitthh tthhiiss ppllaayyeerr
This player can play back a DVD VIDEO disc which carries the corresponding code to the region code of the player shown in the table
above, a marking containing the region code of the player or the "ALL" marking shown below. Even when a DVD VIDEO disc does not
carry any indication of the region code, it may sometimes unable to be played on this player due to certain restrictions.
Icons on the DVD VIDEO discs
Icon
Description
Indicates the region code where the disc can be played.
Number of voice languages recorded with the audio function. The number in the icon indicates the number of
voice languages. (Max. 8 languages)
Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the number of
subtitle languages. (Max. 32 languages)
Number of angles provided by the angle function. The number in the icon indicates the number of angles. (Max. 9
angles)
Aspect ratios that can be selected. "4:3 Letter box" stands for Letter Box and "4:3 Panscan" for Pan/Scan. (See page
17)
In the example on the left, the 16:9 video can be converted into letter box video.
English
7
Playable files with this unit
File Specifications
Category / Item
Extension
Detail
(Audio)
Media
MOVIE [file size : 4GB (Max.)]
MPEG1
.MPG, .MPEG
.MPG, .MPEG
.AVI, .DIVX
Video resolution : 352 x 288 (Max.)
Bit Rate : 1.5M bps (Max.)
Video resolution : 720 x 576 (Max.)
Bit Rate : 1.5M bps (Max.)
Video resolution : 720 x 576 (Max.)
Bit Rate : 8M bps (Max.)
Mpeg1 Layer1 & 2
Mpeg1 Layer1 & 2
MPEG2
CD-ROM
CD-R
CD-RW
DivX® VIDEO *
WAV, MP3, WMA
Dolby Digital
DVD-ROM
DVD-R
MUSIC [file size : 4GB (Max.)]
DVD+R
MPEG Audio
.MP3
Layer III Bit Rate 32 - 384 kbps, CBR/VBR
FS 32k, 44.1k, 48k
Bit Rate 48 - 320 kbps, CBR/VBR
FS 32k, 44.1k, 48k
DVD-RW
DVD+RW
(See page 6.)
WMA
.WMA
PHOTO [file size : 4MB (Max.)]
JPEG .JPG, .JPEG
Video resolution : 3072 x 2048 (Max.)
24 bit True color
•
Depending on the data recording condition and other factors, playback may not be possible.
•
Usable formats for MP3/WMA/JPEG : ISO9660 level 1, 2 (excluding expanded formats : Joliet, Romeo)
Official DivX® Certified product.
*
Plays all versions of DivX® video (including DivX® 6) with standard playback of DivX® media files.
Creating media for playing back on this equipment
Compressing MP3/WMA
Please set up the transfer bit rate setting for the compression software when compressing MP3/WMA files as follow.
MP3 Files : 128 kbps recommended (32 - 384 kbps)
WMA Files : 128 kbps recommended (48 - 320 kbps)
•
•
•
This unit is compatible with 32 kHz, 44.1 kHz (recommended) and 48 kHz sampling frequencies.
This unit is compatible with ID3-TAG Ver. 1. (Alphanumeric sign : up to 30 characters)
DIGITAL output of MP3/WMA data is done not as MP3/WMA data, but as PCM data.
Naming folders and files
Single-byte characters between A and Z, single-byte numerals between 0 and 9, and the single-byte underscore(_) can be displayed. Ensure
that the extension log is attached to all file names.
•
Never add the wrong extension log to any files, the equipment will assume that they can be played back, and this will produce loud noises
in the speakers, resulting in damage of adverse effects.
Note:
Folder names and file names are displayed up to 20 characters. When folder names and file names are recorded with more than 20 characters,
the names will be displayed in abbreviated form.
Confirming media and files
Check to ascertain that MP3/WMA files can be played back correctly on the personal computer in use prior to saving them onto the media.
Check to ensure that the saved file can be played back normally.
It is not possible to confirm that files can be played back correctly while they are being saved onto the
media.
Example for a hierarchical
structure
•
When saving files onto media
Ensure that the session is closed or finalized when data has been written on media. There are cases where
media on which the session has not be closed or finalized will not be played back correctly with this equip-
ment.
•
There are cases where the folder names and file names will not be displayed correctly depending on the
software used to save them.
•
•
•
•
Do not store files or folders other than playable files on media to be played back with this equipment.
It is recommended that ten or less sessions are stored when recording MP3/WMA files onto a media.
In case of a multisession disc, some time may be required until playback begins.
There are cases where playback is not possible when DivX/MP3/WMA/JPEG files (CD-ROM) and music CD
information (CD-DA) are saved on the same media.
DVF-3500
8
Video formats
The TV picture display and disc signal systems can be divided
roughly into two TV formats (NTSC and PAL).
TV formats of major countries
TV Format
Major Countries & Areas
They are variable depending on countries and areas.
Japan, Taiwan, Korea, USA, Canada, Mexico,
Philippines, Chile, etc.
China, U.K., Germany, Australia, New Zealand,
Kuwait, Singapore, etc.
NTSC
This unit has a function for changing the video format accord-
ing to the TV type. Please confirm the type of your TV.
PAL
Checckiinngg tthhee VVideoo FFoorrmmaatt
To seelecctt TTVV TTyyppe
Check the video format of the TV to be used
0
1
Press the [ ] key to remove the disc from the
When the video formats are different :
unit, then close the tray.
Try playing the disc. If the video formats of the disc and TV do
not match, the played video may be black and white or become
as shown below.
8
2
Press and hold the [ ] key on the remote control
for more than 5 seconds to be able to select a TV
type (PAL, NTSC or AUTO).
Top and bottom edges are not
displayed.
Top and bottom areas are
dark.
Picture turbulence due to sync
unmatching.
English
9
For your information
Hanndliinngg ooff ddiisscc
Caree aandd storaaggee
Cautioonn ffoorr ttrraannssport or mmovemennt
is displayed.
3
Wait a few seconds, and then switch the system OFF.
DVF-3500
10
Connections
Caution for connection
CAUTION
Observe the following cautions when installing the system.
Insufficient heat radiation may build up internal heat and
cause a malfunction or fire hazard.
Do not plug the power cord into the power outlet until all
other connections are completed. Before unplugging a con-
nected cord or cable, be sure to set the power key to OFF and
unplug the power cord from the power outlet in advance.
÷
÷
Do not place an object that may hinder heat radiation on the system.
Leave the spaces specified below around the cabinets of the main unit.
Top panel: 50 cm or more
Side panel: 10 cm or more
Back panel: 10 cm or more
Install the system so that the power outlet is easily accessible
from the user, and unplug the power cord from the power
outlet immediately in case of a trouble. Note that the power
supply to the system is not shut down completely by simply
setting the power key to OFF. To shut down the power supply
completely, it is required to unplug the power cord.
Malfunction of microcomputer
If the system does not work properly or the display shows
wrong information even when correct connections are made,
reset the microcomputer referring to "Operation to reset".
(See page 32.)
Connneeccttiingg ttoo a TV with viiddeeoo ((ccoommppoossiittee)) oorr SS--vviiddeeoo iinnppuutt tteerrmmiinnaall
Video cord
Audio cord
TV
Rear panel example (for Australia)
R
L
AUDIO
VIDEO
INPUT
S
VIDEO
*S-video (Commercially available)
(Except for Europe)
*
Connect only either the video (composite) cord or
the S-video cord.
Connneeccttiinngg ttoo aa TTVV wwiitthh SSCCAARRTT iinnppuutt tteerrmmiinnaall ((FFoorr EEuurooppee))
Refer to "TV Output Select (only for Europe)" on page 17.
TV
Rear panel example (for Europe)
INPUT
SCART
*SCART cable (Commercially available)
Note:
Make sure the DVD player is connected directly to the TV and not to a VCR, otherwise the DVD image could be distorted by the copy protec-
tion system.
English
11
Connections
Connneeccttiinngg ttoo aa TTVV wwiitthh CCoommppoonneenntt iinnppuutt tteerrmmiinnaal
Refer to "TV Output Select (only for Europe)" on page 17.
Video cord
Audio cord
TV
Rear panel example (for Europe)
Component cords (Commercially available)
DVF-3500
12
Conneeccttiing to ann AAuudiio ccomponennt
For playback of DTS audio, please connect an AV receiver or an AV amplifier which can decode DTS by digital connection.
Audio cord
Coaxial cable
Rear panel example (for Europe)
TV
R
L
AUDIO
INPUT
VIDEO
COAXIAL OPTICAL
DIGITAL INPUT
Video cable or Component cords
(Commercially available)
AV receiver or AV Amplifier
Amplifier equipped with 2-channel analog stereo or Dolby Pro Logic II / Pro Logic:
Connect the left and right AUDIO OUT jacks on the DVD player to the audio left and right IN jacks on your amplifier, receiver, or stereo
system, using the audio cords.
Amplifier equipped with 2-channel digital stereo (PCM) or a multi-channel decoder (Dolby Digital™ or
DTS):
Connect one of the DVD Player's DIGITAL OUT jacks (COAXIAL) to the corresponding in jack on your amplifier. Use a digital (coaxial)
cable. Select "Bitstream" if you connect the DVD player to an amplifier or other equipment with a multi-channel decoder. (See page 17.)
DTS disclaimer clause
When playing DTS-encoded (CDs, DVDs), excessive noise will be exhibited from the analog stereo outputs. To avoid possible damage to
the audio system, the consumer should take proper precautions when the analog stereo outputs of the DVD player is connected to an
amplification system.
To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the digi-
tal output (S/P DIF, AES/EBU, or TosLink) of the DVD player.
Notes:
•
•
In case an associated system component is connected, also read the instruction manual of the component.
If the audio format of the digital output does not match the capabilities of your receiver (amplifier), the receiver produces a strong, distorted
sound or no sound at all.
English
13
Controls and indicators
Main unit
Display
•
DVD video:
Elapsed time of the title being played.
•
Audio CD, VCD, DivX, MP3, WMA:
Elapsed time of the track (or file) being played.
3
4
5 6
1
7
2
£
Power key (See page 16.)
key (See page 23.)
1
5
6
7
Switches the unit ON and standby.
Starts playback.
7
Disc tray (See page 23.)
key (See page 24.)
2
3
Stops playback.
0
Disc tray open/close ( ) key (See page 23.)
Opens or closes the disc tray.
4 ¢
,
keys (See page 24.)
Skips or searches (by fast forward or fast reverse) a chapter
or track.
Remote control sensor (See page 15.)
4
Remote control unit
The remote control keys with the same names as the
keys on the main system function in the same way as
the keys on the main system.
1
0
!
@
Power key (See page 16.)
1
2
3
Switches the unit ON and standby.
2
3
TOP MENU key (See page 23.)
Accesses menu on a DVD disc.
5 ∞ 2 3
keys
,
,
,
Selects an item in the menu.
ENTER key
4
5
Confirms menu selection.
RETURN key (See page 20.)
4
5
#
$
%
Returns on a VCD with PBC.
ZOOM key (See pages 28, 31.)
Enlarges video image.
6
8
key (See pages 24, 26.)
Pauses playback temporarily/press repeatedly for frame-
by-frame playback.
7
8
9
^
&
SLOW
key (See page 26.)
Starts slow motion playback.
7
key (See page 24.)
Stops playback.
Numeric keys (See pages 26, 29.)
6
7
Selects numbered items in a menu.
AUDIO key (See page 27.)
Selects an audio language or an audio channel.
SUBTITLE key (See page 28.)
Selects a subtitle language.
DVF-3500
14
REPEAT key (See page 24.)
8
9
Operatioonn
Repeats playback.
A-B key (See page 25.)
Repeats sequence from point A to point B.
Remote sensor
6 m (approx.)
MARKER key (See page 27.)
Marks any point during playback.
SEARCH key (See page 27.)
Displays Marker Search menu.
0
OPEN/CLOSE key (See page 23.)
0
!
@
#
Opens or closes the disc tray.
MENU key (See page 23.)
Accesses menu on a DVD disc.
ON SCREEN key (See page 22.)
Accesses On-Screen display.
4 ¢
,
keys (See page 24.)
Skips or searches (by fast forward or fast reverse) a chapter
or track.
Plug the power cord of the system to a power outlet and press
the power key on the remote control unit to turn the system
ON. After the system is switched ON, press the desired opera-
tion key.
£
key (See page 23.)
Starts playback.
P. MODE key (See page 25.)
•
•
•
•
When pressing more than one remote control keys in sequence,
leave a period of about 1 second or more between each press.
The provided batteries are intended for use in checking opera-
tions and their life may be shorter than usual.
When the remote controllable distance becomes short, replace
both of the batteries with new ones.
The system may malfunction if the remote control sensor is ex-
posed to direct sunlight or the light of a fluorescent lamp with
high-frequency lighting system (inverter system, etc.). In this
case, change the system installation to prevent malfunction.
$
%
Enter the program edit mode.
CLEAR key (See pages 26, 27.)
Removes a track number on the Program List or a mark on
the Marker Search menu.
ANGLE key (See page 28.)
^
&
Selects a DVD camera angle.
SETUP key (See page 16.)
Accesses or removes the Setup menu.
RANDOM key (See page 30.)
Plays tracks in random order.
Loaddinng baatttteerriieess
1
Remove the cover.
2
Insert batteries.
•
Insert two R03 batteries following the polarity indications.
3
Close the cover.
English
15
Set Up functions
To diissppllaayy aanndd eexxiitt tthhee MMeennuu
When you turn on for the first
time
The menu for a language selection will appear when you turn
on the unit for the first time. You must select a language to use
the unit.
1
Press [SETUP] key to display the menu. A second
press of [SETUP] key will take you back to initial
screen.
To go to the next level:
3
Press the Cursor right [ ] key.
To go back to the previous level:
2
Press the Cursor left [ ] key.
POWER
POWER
Gennerraall OOppeerraattiion
ENTER
1
Press [SETUP] key.
•
The Setup menu appears.
5 ∞
] keys to select the
2
Use the Cursor up/down [
/
3
]
desired option, then press the Cursor right [
key to move to the second level.
•
The screen shows the current setting for the selected item, as
well as alternate setting(s).
1
2
Press the [POWER] key to power on.
5 ∞
Use the Cursor up/down [ ] keys to select the
3
4
/
second desired option, then press the Cursor
5 ∞2 3
Use [ ] keys to select a language then
/
/
/
3
right [ ] key to move to the third level.
press [ENTER] key and the confirm menu will
appear.
5 ∞
Use the Cursor up/down [ ] keys to select the
/
desired setting, then press [ENTER] key to confirm
your selection. Some items require additional
steps.
2 3
] keys to select [Enter] then press [ENTER]
3
Use [
key.
/
Note:
When the power cord is plugged, wait for several seconds, and
then switch the power on.
£
5
Press [SETUP] key or [ ] key to exit the Setup
menu.
Set up menu
By using the Setup menu, you can make various adjustments to
items such as picture and sound.
You can also set a language for the subtitles and the Setup
menu, among other things. For details on each Setup menu
item, see pages 17 to 19.
ENTER
SETUP
DVF-3500
16
LANGUAGE
Note:
Once the setting for progressive scan output is entered, an image
will only be visible on a progressive scan compatible TV or monitor.
7
If you set Progressive Scan to "On" in error, press and hold [ ] key
for about 3 seconds. Set Progressive Scan to "Off".
TV Output Select
Set the player's TV Output Select options according to the TV
connection type.
For Europe;
RGB: When your TV is connected with the SCART jack.
Y Cb Cr: When your TV is connected with the COMPONENT
VIDEO jacks on the DVD player.
Menu Language
Select a language for the Setup menu and on-screen display.
For Australia;
Disc Audio/ Disc Subtitle/ Disc Menu
Select the language you prefer for the audio Track (disc audio),
subtitles, and the disc menu
S: When your TV is connected with the S VIDEO jack.
Y Cb Cr: When your TV is connected with the COMPONENT
VIDEO jacks on the DVD player.
Original: Refers to the original language in which the disc was
recorded.
Other: To select another language, press numeric keys then
[ENTER] key to enter the corresponding digit number according
to the language code list (See page 21.). If You enter the wrong
Language code, press [CLEAR] key.
DISPLAY
AUDIO
Each DVD disc has a variety of audio output options. Set the
player’s AUDIO options according to the type of audio system
you use.
Progressive Scan
TV Output Select
Off
RGB
TV Aspect
4:3: Select when a standard 4:3 TV is connected.
16:9: Select when a 16:9 wide TV is connected.
Display Mode
Display Mode setting works only when the TV Aspect mode is
set to "4:3".
Letterbox: Displays a wide picture with bands on the upper
and lower portions of the screen.
Dolby Digital/ DTS/ MPEG
Bitstream: Select "Bitstream" if you connect the DVD Player’s
DIGITAL OUT jack to an amplifier or other equipment with a
Dolby Digital, DTS or MPEG decoder.
Panscan: Automatically displays the wide Picture on the entire
screen and cuts off the portions that do not fit.
PCM (for Dolby Digital/ MPEG): Select when connected to a
two-channel digital stereo amplifier. DVDs encoded in Dolby
Digital or MPEG will be automatically down mixed to two-
channel PCM audio.
Progressive Scan
If you are using the COMPONENT VIDEO jacks, but are con-
necting the DVD Player to a standard (analog) television, set
Progressive Scan to "Off".
Off (for DTS): If you select “Off'', the DTS signal is not output
through the DIGITAL OUT jack.
If you are using the COMPONENT VIDEO jacks for connection
to a TV or monitor that is compatible with a progressive scan
signal, set Progressive Scan to "On".
When "On" is selected, the confirmation screen for switching to
Progressive Scan appears. In case of a TV not compatible with
Progressive Scan, the screen disappears and return to the origi-
nal display is made after 10 seconds.
Continued to next page 3
English
17
Set Up functions
3
Select a rating from 1 to 8 using the Cursor up/
Sample Freq. (Frequency)
5 ∞
down [ ] keys.
/
If your receiver or amplifier is NOT capable of handling 96 kHz
signals, select 48 kHz. When this choice is made, this unit auto-
matically converts any 96 kHz signals to 48 kHz so your system
can decode them.
Rating 1-8: Rating one (1) has the most restrictions and rating
eight (8) is the least restrictive.
Unlock
If your receiver or amplifier is capable of handling 96 kHz sig-
nals, select 96 kHz. When this choice is made, this unit passes
each type of signal through without any further processing.
Check the documentation for your amplifier to verify its capa-
bilities.
If you select unlock, parental control is not active and the disc
plays in full.
Note:
•
When you set "Rating" for the first time, you set an area code
first.
When the disc prohibits 96 kHz digital output, the signal always
is put out after down-conversion.
•
If you set a rating for the player, all disc scenes with the same
rating or lower are played. Higher rated scenes are not played
unless an alternate scene is available on the disc. The alternative
must have the same rating or a lower one. If no suitable alterna-
tive is found, playback stops. You must enter the 4-digit pass-
word or change the rating level in order to play the disc.
DRC (Dynamic Range Control)
With the DVD format, you can hear a program's soundtrack in
the most accurate and realistic presentation possible, thanks to
digital audio technology. However, you may wish to compress
the dynamic range of the audio output (the difference between
the loudest sounds and the quietest ones). This allows you to
listen to a movie at a lower volume without losing clarity of
sound. Set DRC to On for this effect.
4
Press [ENTER] key to confirm your rating selec-
tion, then press [SETUP] key to exit the menu.
Password (Security Code)
You can enter or change password.
This function operates only at the time of playback of DVDs re-
corded with Dolby Digital.
1
Select Password on the LOCK menu then press
3
the Cursor right [ ] key.
Vocal
2
Follow step 2 as shown "Rating" part.
"Change" or "New" is highlighted.
Set to on only when a multi-channel karaoke DVD is playing.
The karaoke channels on the disc mix into normal stereo sound.
3
4
Enter the new 4-digit code, then press [ENTER]
key. Input it again to verify.
LOCK (Parental Control)
Press [SETUP] key to exit the menu.
If you forget Password
If you forget your password you can clear using the following
steps:
1
2
Press [SETUP] key to display the Setup menu.
Input the 6-digit number "210499" and the pass-
word is cleared.
3
Enter a new code as described above.
Rating
Area Code
Some movies contain scenes that may not be suitable for chil-
dren to view. Many of these discs contain parental control infor-
mation that applies to the complete disc or to certain scenes on
the disc. Movies and scenes are rated from 1 to 8, depending on
the country. Some discs offer more suitable scenes as an alter-
native.
Enter the code of the country/area whose standards were used
to rate the DVD video disc, based on the list in the reference
chapter.
Ratings are Area-dependent. (See page 21.)
1
Select "Area Code" on the LOCK menu, then press
the Cursor right [ ].
The parental control feature allows you to block access to
scenes below the rating you input, thereby preventing your
children from being able to view material you believe is unsuit-
able.
3
2
3
Follow step 2 as shown "Rating" part.
Select the first character using the Cursor up/
5 ∞
down [ ] keys.
1
Select "Rating" on the LOCK menu then press the
Cursor right [ ] key.
/
3
3
4
5
Shift the cursor using the Cursor right [ ] key
2
To access the Rating, Password and Area Code
features, you must input the 4-digit password
you created. If you have not yet entered a pass-
word you are prompted to do so.
and select the second character using the Cursor
5 ∞
up/down [ ] keys.
/
Press the [ENTER] key to confirm your Area code
selection.
Input a 4-digit password and press [ENTER] key.
Enter it again and press [ENTER] key to verify. If
you make a mistake before pressing [ENTER] key,
press [CLEAR] key.
DVF-3500
18
The rental has been expired.
OTHERS
Rental Expired
Done
Display the authorization error.
PBC
Set Playback Control (PBC) to On or Off.
Authorization Error
On: Video CDs with PBC are played according to the PBC.
This player is not authorized
to play this video.
Off: PBC is switched off and normal playback is made.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures.
Set your preference and monitor’s ability.
Done
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
Note:
The B.L.E. function works NTSC system only.
DivX(R) VOD
You can display the DivX DRM (Digital Rights Management)
Registration code for your unit only.
The Registration code is used for VOD (Video-On-Demand) ser-
vice agent. You can purchase or rent an encrypt movie file.
DivX(R) Video On Demand
Your registration code is : XXXXXXXX
To learn more visit
Done
If you rent the DivX VOD file, it has several options of viewing
limits as shown below.
Display the number which you can watch the file.
View DivX(R) VOD Rental
This rental has 3 views left.
Do you want to use one
of you 3views now?
Yes No
English
19
Set Up functions
Hierarchical structure of VCD
menus (P.B.C. function)
When an item is selected on the menu screen during playback
of a P.B.C.-compatible VCD, another menu with more details
items may be displayed. When a number of menus are connect-
ed in multiple layers in this way, it is said that the menus have a
hierarchical structure. In this structure, the desired scene can be
reached by repeating item selections on the menu screens.
ENTER
RETURN
Example for a hierarchical structure
a: First level (menu)
b: Second level (submenu)
c: Third level (scenes)
Advancing
When an item is selected on the menu screen with the [ENTER]
key or the numeric keys, advance is made to the next lower
menu level. When the advance destination is the "scene" to be
played, the contents will be played.
•
When several menus (scenes) can be selected in each level,
screen switching is possible with the keys
(PREV.).
¢
4
(NEXT) and
Returning
Each time the [RETURN] key is pressed, return is made to the
next higher menu.
DVF-3500
20
DVD menu language code list
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Tamil
Tatar
Hebrew
Hindi
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Polish
Italian
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Danish
Dutch
English
Esperanto
Estonian
Faroese
Latvian, Lettish
Sindhi
Area Code code list
Area
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Islands
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
Code
ET
FJ
FI
FR
DE
GB
GR
GL
HM
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
Area
Code
MY
MV
MX
MC
MN
MA
NP
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Code
SA
SN
SG
SK
SI
ZA
KR
Area
Code
AF
AR
AU
AT
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles AN
New Zealand
Nigeria
Norway
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
NL
ES
LK
SE
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation RU
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
RO
EG
SV
LU
Zimbabwe
El Salvador
English
21
Basic playback of disc
On-Screen Display during playing DivX
On screen display
The on-screen Banner Display contains many playback features.
To see the Banner Display, press [ON SCREEN] key while a disc is
Track Number
5 ∞
] keys to move through
playing. Use the Cursor up/down [
the different features in the Banner Display. Each feature is illus-
trated with an icon.
/
Time search
Audio language and Digital
Audio Output mode
ON SCREEN
Subtitle language
Note:
Example:
The on screen display is switched off when no operation is per-
formed for a few seconds.
On-Screen Display during playing DVD video
Title Number
Last Scene Memory
This player memorizes last scene from the last disc that is
viewed. The last scene remains in memory even if you remove
the disc from the player or switch off the player. If you load a
disc that has the scene memorized, the scene is automatically
recalled.
If you don't want to use the Last Scene Memory, press the [
key during stop.
Chapter Number
Time search
7
]
Audio language and Digital
Audio Output mode
Subtitle language
Angle
On-Screen Display during playing VCD
Track Number
(or PBC mode)
Note:
This player does not memorize the scene of a disc if you switch off
the player before commencing to play the disc.
Time search
Audio Channel
DVF-3500
22
To starrtt ppllaayybaacck ooff aauddioo CCDD,, DDiivvXX,,
MP3,, WWMMAA oorr JJPPEEG ffiless
Basic play
Label side
It is not possible to play back folders and files that exceed the
maximum limitations of the media.
POWER
A certain amount of time is required for the player to confirm
the media on which DivX/MP3/WMA/JPEG files have been re-
corded before playback will commence.
5 ∞
] keys to select desired
Press Cursor up/down [
/
£
track or file, then press the [ ] key or the [ENTER]
key to start playback.
Press [MENU] key to go to the next page.
Example of MP3 menu
File types
POWER
TOP MENU
ENTER
OPEN/CLOSE
MENU
MUSIC
Example of JPEG menu
Preview window
1
2
3
4
Press the [POWER] key to power on.
0
Press the [ ] key to open the tray.
Place a disc.
Start playback.
To starrtt ppllaayybacckk of DVD viiddeeoo,, aauu--
diio CDD or VCDD
•
When different file types like music, photo, and movie files are
mixed on one disc, press the [TOP MENU] key and select the file
type (music, photo, movie; see page 8.) to be played back.
£
Press the [ ] key.
Notes:
Elapsed time of the title, track or file display
•
•
After all files of a folder have been played, playback will stop.
If you are in a file list on the MP3/WMA menu and want to return
to the folder list, use Cursor up/down [
and press [ENTER] key.
5 ∞
/
] keys to highlight
£
•
When [ ] key is pressed while a tray is open, the tray closes
automatically, and then playback begins.
Note:
When a Disc Menu appears on the screen
In case of interactive DVDs, a Disc Menu appears on the screen.
Then press [ENTER] key to select specific menu you want to play by
using Cursor keys.
English
23
Basic playback of disc
Seeaarching
During playback, press the [
Disc playback features
4
¢
] or [ ] key for
more than 2 seconds to select the searching speed,
then release the key.
4
¢
] key switches the searching
Each press and hold the [
speed.
] or [
At the time of DVD video or DivX playback
#
(Normal speed)
1
2
3
4
5
##
###
####
#####
At the time of VCD playback
#
(Normal speed)
1
2
3
4
##
###
####
At the time of audio CD, MP3 or WMA playback
#
(Normal speed)
1
2
3
4
##
##
##
x 2
x 4
x 8
Notes:
•
You won't hear the sound (audio) on the DVD, VCD and DivX
£
•
•
Press the [ ] key at any time to resume normal playback.
P.B.C. on mode of VCD, the search function does not work.
when you're using the Skip, Search, Step or Slow motion fea-
tures.
•
Playback features are not available during the opening credits of
a movie.
Repeat play
To stop playback
Desired title, chapter, track or disc can be played back repeat-
edly.
7
Press the [ ] key.
REPEAT
To pause playback
8
Press the [ ] key.
•
•
During playback, press the [REPEAT] key.
Repeat icon
Each press pauses and plays the disc alternately.
During DVD, VCD playback, step operation is performed each
time this key is pressed. (See page 26.)
Each press switches the selection.
At the time of DVD video playback
Skipping chapters, tracks or files
"Chapter"
1
2
3
"Title"
"Off" (Repeat off)
4
¢
] key.
Press the [
•
] or [
At the time of audio CD, VCD, DivX, MP3 or WMA playback
The chapter (or track) in the direction of the key pressed is
skipped, and the selected chapter (or track) will be played from
the beginning.
"Track"
1
2
3
"All"
Goes off (Repeat off)
4
] key is pressed once during playback, the chap-
•
•
When the [
ter (or track) being played will be played from the beginning.
•
To cancel repeat playback, press the [REPEAT] key and select
"Off".
4
When the [
] key is pressed within 3 seconds after the start
of chapter (or track) playback, playback starts from the start of
the preceding chapter (or track).
Notes:
¢
] once during Repeat Chapter or Repeat Track
•
If you press [
Note:
playback, the repeat playback cancels.
P.B.C. on mode of VCD, the Repeat play function does not work.
The Chapter feature won't work if the disc isn't formatted with
separate chapters.
•
DVF-3500
24
A-B Repeat play
Program play
The A-B repeat function lets you mark a segment to repeat
between the beginning "A" and the end "B" of the segment you
want to replay.
You can listen to the desired tracks of the current CD, MP3 or
WMA in any desired order.
ENTER
A-B
P. MODE
CLEAR
REPEAT
1
Press the [A-B] key when you want to choose a
scene (sound) as the beginning point.
Repeat A icon
Prooggrraamm EEddiitt
•
"A" display appears.
2
Press the [A-B] key again to choose a scene (sound)
as the end point.
1
Insert a disc and close the tray.
•
Audio CD or MUSIC menu appears.
Repeat A-B icon
2
Press the [P. MODE] key.
•
The
mark will appear to the right of the word "Program" on
the right side of the menu screen.
•
•
"A-B" display appears and the repeat sequence begins.
To cancel A-B Repeat playback, press the [A-B] key.
Example of Audio CD menu
mark
"List"
"Program"
•
To exit the Program Edit mode, press the [P. MODE] key again.
3
Select a specific track on the "List" by press-
5 ∞
] keys, then press the
ing Cursor up/down [
/
[ENTER] key to place the selected track on the
"Program" list.
4
5
You can select maximum 30 values by repeating
step 3.
Select the track you want to start playing on the
5 ∞
]
Program list by pressing Cursor up/down [
keys.
/
£
6
•
Press the [ ] key to start.
Playback begins in the order in which you programmed tracks.
Playback stops after all of the tracks on the Program list have
played once.
7
•
The unit stops when the [ ] key is pressed. To restart program
£
play, press the [ ] key.
English
25
Basic playback of disc
Movie disc playback
To reepeeaatt pprroogramm ppllay
During program playback, press the [REPEAT] key.
Each press switches the selection.
"TRACK" : repeats the current track or file.
"ALL" : repeats all the tracks (files) on programmed list.
Goes off (repeat off)
1
2
3
ON SCREEN
SLOW
Note:
Numeric keys
¢
If you press [
] once during Repeat Track playback, the repeat
playback cancels.
Delete aa tracck froomm PPrrooggrraamm lliist
1
During stop mode, press [P. MODE] and the
mark will appear.
STEP (freeze frame and frame ad-
vance)
2 35 ∞
] keys to select the
2
Press the Cursor [
/
/
/
track that you wish to delete from the Program
list.
8
During playback, press the [ ] key.
3
Press the [CLEAR] key.
•
•
Each time you press the key, the picture advances one frame.
£
Press the [ ] key to resume normal playback.
Delete tthee ccoommpplleettee PPrrooggrraamm lliist
Slow motion playback
1
During stop mode, press [P. MODE] and the
mark will appear.
During playback, press the [SLOW ] key.
2
Select "Clear All", then press the [ENTER] key.
•
•
The complete program for the disc is deleted.
The programs are also cleared when the disc is removed.
Each press switches the motion speed.
(Slow Reverse is not possible)
1/16
1/8
1/4
1
2
3
4
1/2
£
•
Press the [ ] key to resume normal playback.
Playback from desired title, chapter
or track
Because DVD video discs use digital technology, a title can be
divided into individual chapters (similar to tracks on a CD).
At the time of DVD video playback
1
2
Press the [ON SCREEN] key.
5 ∞
Press the Cursor up/down [ ] keys to select the
title or chapter icon.
Title Number
/
Chapter Number
£
3
Press the numeric keys, then press the [ ] key.
£
To select track No. 23: 2, 3 and
Note:
The Chapter feature won't work if the disc isn't formatted with
separate chapters.
DVF-3500
26
At the time of VCD playback
Using Marker
The marker feature lets you mark a point on the disc that you
can go to quickly. You can store up to 9 marker points
£
Press the numeric keys, then press the [ ] key.
£
To select track No. 23: 2, 3 and
Note:
P.B.C. on mode of VCD, the Selecting a Track function may not
work. (See page 20.)
ENTER
CLEAR
Select Audio Language
If the disc was created with different language tracks, you can
use the [AUDIO] key to temporarily change the DVD player’s Au-
dio setting.
MARKER
SEARCH
AUDIO
Create tthhee MMaarrkkeer
When you reach the scene you want to mark, press
[MARKER] key.
Marker icon
During playback, press the [AUDIO] key.
The language is switched each time the [AUDIO] key is pressed.
•
•
The marker icon appears on the TV screen briefly.
Repeat to enter up to 9 marker points.
DVD Audio language icon
DivX Audio language icon
To reeccaallll oorr cclearr aa mmarrkkeedd sscenne
1
During playback, press the [SEARCH] key.
Marker search icon
Notes:
•
The language feature only works if the disc was created with
multiple audio tracks.
•
The marker search menu appears on the screen.
•
When you chose an audio language by the [AUDIO] key, you
only override the audio language setting in the DVD Player's
main menu (in the Language Preferences menu within Setup
menu) temporarily.
2 3
] keys to
2
Press the Cursor right/left [
select a marker number that you want to
recall or clear.
/
3
Press the [ENTER] key to playback from the
marked scene or press the [CLEAR] key to
clear the selected number.
Select the Audio channel
You can choose to play back only the right or the left channel of
audio recorded on the disc, or you can select stereo playback.
Notes:
•
•
Depending on the disc, the marker function may not work.
P.B.C. on mode of VCD, the marker function does not work. (See
page 20.)
The marker points are cleared each time a disc is removed from
the player or when the power is turned off.
AUDIO
•
During VCD playback, press the [AUDIO] key.
Audio channel icon
Each press switches the selection.
LEFT
RIGHT
STEREO
1
2
3
English
27
Movie disc playback
Notes:
Select Camera angle
Some disc contains multiple angles particular scene or se-
quence. If the disc only has one angle, this feature won’t work.
When you are playing a DVD disc contains scenes recorded dif-
ferent camera angles, the angle indicator will blink on the TV
screen.
•
The subtitle feature only works if the disc was created with mul-
tiple subtitle tracks.
•
•
The subtitle menu of the disc appears in some discs.
The subtitle file of the DivX file is displayed only srt, txt, smi, ssa
and sub.
•
If there is no information or there is a code that can not read in
the DivX file, " 1 " etc are displayed.
Notice for displaying the DivX subtitle
If the subtitle does not display properly, please follow the steps
below.
1 During playback, press and hold [SUBTITLE] key for about 3 sec-
ANGLE
onds. The language code will appear.
2 3
] keys to select another lan-
2 Press the Cursor right/left [
/
guage code until the subtitle is displayed properly.
3 Press and hold [SUBTITLE] key for about 3 seconds.
1
During the angle indicator has blinked, press the
[ANGLE] key.
Zoom function
Use zoom to enlarge the video image.
Angle icon
ZOOM
CLEAR
2
Select the Camera angle with press the [ANGLE]
key.
1
During playback, press the [ZOOM] key.
•
The square frame appears briefly in the right bottom of the pic-
ture.
Each press switches the selection.
100 % size (normal size)
400 % size
1600 % size
1
2
3
2 35 ∞
] keys to move
2
Press the Cursor [
/
/
/
through the zoomed picture.
Select Subtitle Language
You can change the Subtitle language while you’re watching a
disc (but only if the disc was created with subtitles).
•
To resume normal playback, press [ZOOM] or [CLEAR] key re-
peatedly.
Note:
Zoom may not work on some DVDs.
SUBTITLE
During playback, press the [SUBTITLE] key.
The language is switched each time the [SUBTITLE] key is pressed.
Subtitle language icon
DVF-3500
28
Time Search
To start playing at any chosen time on the disc.
ENTER
ON SCREEN
CLEAR
Numeric keys
1
2
During playback, press the [ON SCREEN] key.
5 ∞
Press Cursor up/down [ ] keys to select the
time clock icon.
/
Time clock icon
•
"--:--:--" appears.
3
Press Numeric keys to input the required start
time in hours, minutes and seconds from left to
right.
•
If you enter the wrong numbers, press [CLEAR] to remove the
numbers you entered. Then input the correct numbers.
4
Press the [ENTER] key to confirm.
•
Playback starts from the selected time.
English
29
Music disc playback
To display the ID3 tag
When playing a file containing information such as track titles,
you can see the information by pressing [ON SCREEN] key.
Press the [ON SCREEN] key to display the ID3 tag.
•
Title, Artist, Album, Year and Comment display appears on the
TV screen.
ON SCREEN
Each press switches the selection.
(File name)
Title
1
2
3
4
5
6
Numeric keys
AUDIO
Artist
Album
Year
Comment
RANDOM
REPEAT
•
If there is no information, "No ID3 Tag Info" appear on the dis-
play.
Using the TV screen to start
playback
Once you insert an audio CD , MP3 or WMA disc a menu appears
on the TV screen.
Random play
The tracks of the disc are played in random order.
During playback, press the [RANDOM] key.
•
•
The Random Play display appears on the TV screen.
Each time you press [RANDOM] key, random play would be on
and off.
By pressing [
another track and resumes random playback.
Audio CD menu
¢
] key during random playback, the unit selects
•
To caancell rraanndom play
7
1
Press the [ ] key to stop playback.
2
Press the [RANDOM] key to cancel random play-
back.
MP3/WMA menu
To reeppeeaatt rraannddom ppllay
During random playback, press the [REPEAT] key.
Each press switches the selection.
"TRACK"
1
2
3
"ALL"
Goes off (repeat off)
5 ∞
] keys to select a track
Press the Cursor up/down [
/
£
then press [ ] or [ENTER] and playback starts.
Note:
•
After all tracks of a disc have been played in random order, play-
back will stop.
•
P.B.C. on mode of VCD, the random play function does not work.
Playback from desired track
Press the numeric keys.
To select track No. 23: 2, 3
DVF-3500
30
Photo files playback (JPEG files only)
To rotate picture
5 ∞
] keys to rotate the
Press the Cursor up/down [
/
picture clockwise or counter clockwise.
RETURN
ZOOM
ENTER
To hide the menu bar
Press the [RETURN] keys to hide the menu bar.
To start playback
Once you insert an audio JPEG disc a menu appears on the TV
screen.
Hide
Menu bar
•
Switching between display and no display is done each time the
[RETURN] key is pressed.
5 ∞
] keys to select a
1
Press the Cursor up/down [
/
folder then press the [ENTER] key.
2
A list of files in the folder appears. If you are in a
file list and want to return to the previous Folder
Slide show
The Slide show function can be used to switch photo images
automatically from one file to the next.
There are 3 Slide speed options.
5 ∞
list, use the Cursor up/down [ ] keys to high-
/
light and press the [ENTER] key.
£
3
Select desired file, then press the [ ] or [ENTER]
key.
1
2
Insert a disc and close the tray.
2 35 ∞
Press Cursor [ ] keys to highlight the
/
/
/
speed icon (
).
Preview window
•
Go to step 4 if the slide speed is not to be changed.
2 3
3
Press Cursor left/right [
/
] keys to select the
option you want to use.
Each press switches the selection.
>>> : Fast
1
2
3
Zoom function
>> : Normal
>
: Slow
Use zoom to enlarge the photo image.
5 ∞
Press Cursor up/down [
4
/
] keys to select the
1
•
During playback, press the [ZOOM] key.
The square frame appears briefly in the right bottom of the pic-
ture.
icon and then press the [ENTER] key.
•
Playback starts.
Each press switches the selection.
100 % size (normal size)
400 % size
1600 % size
1
2
3
2 35 ∞
] keys to move
2
Press the Cursor [
/
/
/
through the zoomed picture.
•
To resume normal playback, press [ZOOM] or [CLEAR] key re-
peatedly.
English
31
Troubleshooting
Troubles are not always due to malfunction or failure of the system. In case of a trouble, check the following tales before calling for ser-
vice.
Operation to reset
The microprocessor may fall into malfunction (impossibility to operate erroneous display, etc.) when the power cord is unplugged
while power is ON or due to an external factor.
In this case, switch off the power, wait for several seconds, and then switch the power on again.
DVD player unit
Symptom
Remedy
The system cannot be switched ON.
•
When the power cord is plugged, wait for several seconds, and then switch the
power on.
£
£
Playback does not start when the [
key is pressed.
]
•
•
Load a disc and press the [ ] key.
There are no signals recorded on the side of the disc being played. Turn the disc
over and properly place it on the disc tray.
Playback starts but no image/sound is
seen heard.
•
•
Turn on the TV.
Properly reconnect the connection cords. (See pages 11 - 13.)
The picture is disrupted when the image
is fast forwarded or fast reversed.
•
The picture is slightly disrupted during fast forward and fast reverse operations.
This is not a malfunction.
No sound is heard.
•
•
•
Properly connect the audio cords. (See page 13.)
Set the sound volume to an appropriate level.
The player is in a special playback mode. Press the [ ] key to resume normal play-
£
back mode.
No picture is displayed.
•
Setting to progressive mode has been done for a TV not compatible with progres-
sive mode. (See page 17.)
The picture does not look good or the
picture/sound quality is poor.
•
•
•
A nearby device is generating noise. Separate this unit as far as possible from the
device you think is generating the noise.
Refer to the "Care and storage of disc" section and wipe dirt from the disc. (See
page 10.)
Refer to the "Be careful against condensation" section and evaporate the conden-
sation. (See page 10.)
It takes a while for the disc to start play-
ing.
•
Time is required for the unit to detect the disc type and size and for the rotation of
the motor to stabilize. This is not a malfunction. Approximately 10 to 20 seconds
are required for a disc to start playing, although the time differs depending on the
disc.
The tray opens automatically.
•
•
Properly place the disc on the tray.
The top and bottom of the screen cannot
be seen, or the screen becomes black-
and-white.
Refer to the "Video formats" section, and use a disc with the appropriate video for-
mat for your TV or a TV with the appropriate video format for the disc. (See page 9.)
The subtitle is not displayed.
•
The subtitle cannot be displayed when the DVD disc being played does not contain
the recording of subtitles.
•
•
Press the [SUBTITLE] key to switch on the subtitle mode.
The voice (or subtitle) language cannot
be changed.
The voice (or subtitle) language cannot be changed when the DVD disc being
played does not contain the recording of more than one voice (or subtitle) lan-
guage.
The viewing angle cannot be changed.
•
The viewing angle cannot be changed when the DVD disc being played does not
contain the recording of more than one angle.
•
•
More than one viewing angle may be recorded only in limited sections in a disc.
Playback will not start even after a title
is selected.
Check the viewing restriction level (Rating) setting. (See page 18.)
The parental level cannot be changed.
•
You have forgotten the password. Set the initial setup to the factory setup with the
following procedure.
Press the [SETUP] key on the remote to display the Setup menu.
Input the 6-digits number "210499" and the password is cleared.
Enter a new code. (See page 18.)
1
2
3
DVF-3500
32
Symptom
Remedy
The voice or subtitle language selected
in the initial setting is not played.
•
•
•
Use a DVD disc containing the recording of the selected voice or subtitle language.
Press [SUBTITLE] or the [AUDIO] key on the remote and select the language.
The DVD specifications provide for selection at the menu screen. Select at the
menu screen of the disc.
Menu screen messages are not shown in
the desired language.
•
•
Select disc menu language. (See page 17.)
A VCD cannot be played using menus.
Menu playback is available only with VCD discs recorded with P.B.C.
Remote control unit
Symptom
Remedy
Remote control operation is not pos-
sible.
•
•
Replace with new batteries. (See page 15.)
Operate the unit inside the remote controllable range. (See page 15.)
Inhibition icon
Symptom
Remedy
•
Playback is restricted intentionally by the software producer. Please try another
operation.
The inhibition icon is displayed
and remote control is not pos-
sible.
English
33
Specifications
[Type]
System...................................................................DVD video player
Laser................................................................ Semiconductorlaser
[Audio Block]
Frequency response
Sampling frequency ; 44.1 kHz ........................... 4 Hz ~ 20 kHz
Sampling frequency ; 48 kHz................................ 4 Hz ~ 22 kHz
Sampling frequency ; 96 kHz............................... 4 Hz ~ 44 kHz
Signal to noise ratio ........................................... More than 100 dB
Dynamic range.......................................................More than 92 dB
Total harmonic distortion .................... Less than 0.020 % (1 kHz)
Analog output level/impedance................................... 2 V / 330 Ω
Digital output level/impedance
COAXIAL ............................................................... 0.5 Vp-p / 75 Ω
[Video Block]
Video output format..................................................... NTSC/PAL
Composite video output level................................ 1 Vp-p (75 Ω)
S-video output level (For Australia)
(Y-signal)............................................................... 1 Vp-p (75 Ω)
(C-signal)
NTSC......................................................... 0.286 Vp-p (75 Ω)
PAL ........................................................... 0.300 Vp-p (75 Ω)
Component Video output level
(Y-signal)............................................................... 1 Vp-p (75 Ω)
(CB-signal) .........................................................0.7 Vp-p (75 Ω)
(CR-signal) .........................................................0.7 Vp-p (75 Ω)
RGB output level (SCART) (For Europe) ..............0.7 Vp-p (75 Ω)
Horizontal resolution.................................. More than 500 lines
Video signal to noise ratio ................................More than 68 dB
[General]
Power consumption................................................................. 8 W
Standby power consumption .............................Less than 0.6 W
Dimensions........................................................... Width: 440 mm
Height: 41 mm
Depth: 204 mm
Weight (net) .......................................................................... 1.5 kg
÷
÷
Design and specifications are subject to change without notice.
Full performance is not guaranteed in extremely cold environ-
ments (under water-freezing temperatures).
DVF-3500
34
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOM-
MENDED THAT THE USER SWITCH THE CONNECTION TO THE "STANDARD DEFINITION" OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525P AND 625P DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
dealer for information or service on this product.
Model
Serial Number
|