JVC Transmit High Quality Sound AA T100BT User Manual

English

FCC INFORMATION

Registering to a Bluetooth device – Pairing

This device complies with Part 15 of the FCC Rules. Operation is subject to the

Before pairing...

2 Connect the unit to the dock

Thank you for purchasing this JVC product. Before you begin operating this unit, please read

the operating instructions carefully to be sure you get the best possible performance. If you have

any questions, consult your JVC dealer.

following two conditions:

•

Turn off the iPod.

connector on the bottom of the

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undesired operation.

Place the target Bluetooth device within 1 m

of the unit.

iPod, then turn on the iPod.

The unit automatically starts pairing and

the LED indicator flashes rapidly. When

the pairing is completed, flash will become

slower after the pairing completed.

CAUTION: Changes or modifications not approved by JVC could void user’s

authority to operate the equipment.

1 Turn on the target Bluetooth

device and execute pairing

operation on the device to find

the unit.

BLUETOOTH TRANSMITTER

ÉMETTEUR BLUETOOTH

TRANSMISOR BLUETOOTH

CAUTION

1. For your safety…

Contact

4. To protect the transmitter, DO NOT…

● allow them to get wet

● shake them or drop them against hard

objects

Address:

JVC AMERICAS CORP.

● Never use the headphones when driving

a car, motorcycle, or bicycle. This could

result in an accident.

JVC COMPANY OF AMERICA

1700 Valley Road, Wayne, N.J. 07470

Telephone: 1 (800) 252-5722

● Pay special attention to traffic around

you when using the headphones outside.

Failure to do so could result in an

accident.

● Be careful not to turn up the sound

volume too high. Your hearing can

be damaged by listening to sounds at

excessive volume for long periods.

● Do not disassemble or modify the

transmitter.

● Do not allow flammable, water or

metallic objects to enter the transmitter.

● In the dry air such as in winter, you

may feel a static shock when using the

transmitter.

2. Avoid using the transmitter…

● in places subject to excessive humidity or

dust

● insert forcibly when connecting the unit;

otherwise the unit and the connected

device may be damaged.

•

The pass code* of the unit is set to “0000.” If the pass code of the target Bluetooth device is

other than “0000,” you cannot execute pairing. When the target device requests the pass code

during pairing operation, enter “0000.”

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

AA-T100BT -J/C

● apply excessive force to the unit when

connected; otherwise the unit and the

connected device may be damaged.

● touch the terminals of the unit and the

connected device or contact metallic

object to them; otherwise damage or

malfunction may be caused with poor

contact or a static shock.

* also called as “pass key,” “PIN number,” etc.

The pairing mode will be canceled about in 60 seconds. In this case, turn off the iPod and

disconnect the unit, and then perform the pairing operation again.

Listening to Music

5. About iPod…

Preparation:

● If the iPod does not play correctly, please

update your iPod software to the latest

version. For details about updating your

iPod, check on the Apple web site.

<http://www.apple.com>

3 Start playback of the iPod.

Refer to the iPod’s instruction manual for

the operation of the iPod.

•

Reorient or relocate the receiving antenna.

•

Finish pairing between the unit and the

Bluetooth device.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

If the target Bluetooth device supports

the AVRCP of the Bluetooth Profile,

play, pause and skip (forward/reverse)

functions are available from the target

Bluetooth device.

1 Turn on the Bluetooth device.

● Sound distortion may occur when playing

back audio source with high recording

levels. When distortion occurs, it is

recommended to turn off the equalizer of

the iPod. For information on operating

the iPod, see the iPod instruction manual.

● JVC is not responsible for any loss of or

damage to iPod that might result from

the use of this product.

•

Consult the dealer or an experienced radio/TV technician for help.

2 Connect the unit to the dock

connector on the bottom of the

iPod, then turn on the iPod.

The unit automatically turns on and will

connect to the target Bluetooth device.

● in places subject to extremely high (over

40°C or 104°F) or low (under 0°C or

32°F) temperatures

IC INFORMATION

3. DO NOT leave the transmitter…

● exposed to direct sunlight

● near a heater

To stop using the unit,

Turn off the iPod and pull off the unit straight

from the iPod.

This device complies with RSS-210 of the IC Rules. Operation is subject to the

following two conditions:

•

If the connection is not completed within

five minutes, the unit automatically turns

off. In this case, turn off the iPod and

disconnect the unit, and then repeat the

procedure from step 1.

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undesired operation of the device.

CAUTION: Changes or modifications not approved by JVC could void user’s

authority to operate the equipment.

About Bluetooth

Contact

Address:

JVC CANADA INC.

LED flashing patterns

Cautions on Bluetooth

communication

INSTRUCTIONS

21 Finchdene Square, Toronto, ON M1X 1A7

Telephone: (416) 293-1311

e-mail: [email protected]

Status

LED

Flashing pattern

MANUEL D’INSTRUCTIONS

•

Microwaves emitted from Bluetooth devices

may affect the operation of electronic

medical devices. Turn off this unit and other

Bluetooth devices in hospitals, airplanes,

trains, or crowding places.

Bluetooth devices use 2.4 GHz band, which

is the same as that used by wireless LAN

devices and microwave oven. Interference

may occur near these devices and cause

noise, disconnectivity, or a decrease of

communication speed.

Connection with all Bluetooth devices cannot

be guaranteed. Connectivity, operation,

display indication or function may differ

depending on the characteristics and

specification of the devices.

Some Bluetooth devices take more time to

establish connection.

Pairing

Blue

●-●-●-●-●-●-●-●-●-●-●-●-●-

●-●-●--------------●-●-●----------

●-●-----------------●-●-------------

●---------------------●-----------------

Bluetooth is a short-range wireless radio

communication technology for the mobile

device such as cellular phones, portable PCs,

and other devices. The Bluetooth devices can

be connected without cables and communicate

each other.

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Industry Canada’s RSS-210. These limits