CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
KD-S811R/KD-S713R/
KD-S711R
KD-S811R
KD-S713R
KD-S711R
COMPACT
DIGITAL AUDIO
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende
handleiding.
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
GET0013-001A
[E]
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit ...............................
2
SOUND ADJUSTMENTS .................. 17
Adjusting the sound ................................. 17
Using the
LOCATION OF THE BUTTONS............
Control panel ............................................
4
4
Sound Control Memory (SCM) .............. 17
Storing your own sound adjustments ....... 18
BASIC OPERATIONS ......................
5
5
Turning on the power ................................
OTHER MAIN FUNCTIONS ............... 19
Setting the clock ...................................... 19
Changing the general settings (PSM) ...... 19
Detaching the control panel...................... 22
RADIO BASIC OPERATIONS .............
Listening to the radio ................................
Storing stations in memory .......................
Tuning into a preset station.......................
6
6
7
8
REMOTE CONTROLLER .................. 23
(With an optionally purchased remote
RDS OPERATIONS ........................
What you can do with RDS EON..............
Other convenient RDS functions and
9
9
controller) (only for KD-S811R)
Installing the battery ................................. 23
Using the remote controller ...................... 24
adjustments ........................................... 12
TROUBLESHOOTING...................... 25
CD OPERATIONS .......................... 14
Playing a CD ............................................ 14
Locating a track or a particular portion on a
CD ......................................................... 15
Selecting CD playback modes.................. 15
Prohibiting CD ejection ............................. 16
MAINTENANCE ............................ 26
Handling CDs .......................................... 26
SPECIFICATIONS .......................... 27
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
BEFORE USE
*Temperature inside the car....
*For safety....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
3
LOCATION OF THE BUTTONS
Control panel
u
i o
;
a s d
f
h
j
g
Display window
45
6 7
8
2 3
1
w
y
9 p q
e r t
1
(standby/on/attenuator) button
Display window
2 Control dial
3 DISP (display) button
4 AM button
5 CD button
6 FM button
u Volume (or audio) level indicator
Equalization Pattern indicator
i Tuner reception indicators
STEREO, MONO
o RND (random) indicator
; RDS indicators
AF, EON, REG, TP, PTY
a “SCM” indicator
s LOUD indicator
d Sound mode indicators
BEAT, SOFT, POP
f CD indicator
g Band indicators
FM1, FM2, FM3
AM
h Main display
j CD IN indicator
7 0 (eject) button
8
4
/¢
buttons
•
Also functions as SSM buttons when pressed
together.
9 SEL (select) button
p Remote sensor (only for KD-S811R)
q MO (monaural) button
RND (random) button
w Number buttons
e TP (traffic programme)
RDS (radio data system) button
r PTY (programme type) button
t SCM (sound control memory) button
y
(control panel release) button
4
BASIC OPERATIONS
1
3
2
4 Adjust the sound as you want (see
Turning on the power
page 17.)
1 Turn on the power.
To drop the volume in a moment
Press
briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you rotate the control dial clockwise, you can
also restore the sound.
Note on One-Touch Operation:
When you select a source in step 2 below, the power
automatically comes on. You do not have to press
this button to turn on the power.
2 Select the source.
To operate the tuner (AM or FM),
see pages 6 – 13.
To turn off the power
Press and hold
for more than 1 second.
To operate the CD player,
see pages 14 – 16.
Note:
When you use this unit for the first time, set the built-in
clock correctly, see page 19.
3 Adjust the volume.
CAUTION on Volume Setting
To increase the volume.
CDs produce very little noise compared with other
sources. If the volume level is adjusted for the tuner,
for example, the speakers may be damaged by the
sudden increase in the output level. Therefore, lower
the volume before playing a disc and adjust it as
required during playback.
To decrease the volume.
Volume level indicator
Volume level appears.
5
RADIO BASIC OPERATIONS
To stop searching before a station is received,
press the same button you have pressed for
searching.
Listening to the radio
You can use either automatic searching or manual
searching to tune into a particular station.
Searching a station manually:
Manual search
Searching a station automatically:
Auto search
1 Select the band (AM, FM1 – 3).
1 Select the band (AM, FM1 – 3).
FM2
FM3
FM1
FM2
FM3
FM1
AM
AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
Selected band appears.
2 Press and hold ¢
or 4
until
Audio (see page 21) or volume level
indicator
"M"(manual) starts flashing on the
display.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2 Start searching a station.
Press ¢
to search
stations of higher
frequencies.
Press 4
stations of lower
frequencies.
to search
Selected band appears.
When a station is received, searching
stops.
6
3 Tune into a station you want while“M”
Storing stations in memory
is flashing.
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
Press ¢
stations of higher
frequencies.
to search
• Manual preset of both FM and AM stations
Press 4
to search
stations of lower
frequencies.
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).
• If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.
1 Select the FM band (FM1 – 3) you want
to store FM stations into.
• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for FM
and 9 kHz intervals for AM – MW/LW) until
you release the button.
• Each time you press the button, the FM
band changes as follows:
When an FM stereo broadcast is hard to
receive:
FM2
FM3
FM1
Press MO RND (monaural/random) while listening
to an FM stereo broadcast.
• Each time you press the button, the MO indicator
lights up and goes off alternately.
2 Press and hold both buttons for more
than 2 seconds.
Lights up when receiving an
FM broadcast in stereo.
“SSM” appears, then disappears when automatic
preset is over.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3.)
These stations are preset in the number buttons —
No.1 (lowest frequency) to No.6 (highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator goes
off).
7
Notes:
Manual preset
• A previously preset station is erased when a new station
is stored in the same preset number.
• Preset stations are erased when the power supply to the
memory circuit is interrupted (for example, during
battery replacement). If this occurs, preset the stations
again.
You can preset up to 6 stations in each band (FM1,
FM2, FM3 and AM) manually.
Ex: Storing an FM station of 88.3 MHz into the
preset number 1 of the FM1 band
1 Select the FM band (FM1 – 3) you
want to store FM stations into (in
this example, FM1).
Tuning into a preset station
• Each time you press the button, the FM
band changes as follows:
You can easily tune into a preset station.
Remember that you must store stations first. If you
have not stored them yet, see “Storing stations in
memory” on page 7.
FM2
FM3
FM1
1 Select the band (AM, FM1 – 3).
2 Tune into a station of 88.3 MHz.
FM2
FM3
FM1
Press ¢
to tune in
stations of higher
frequencies.
AM
2 Select the number (1 – 6) for the preset
Press 4
stations of lower
frequencies.
to tune in
station you want.
3 Press and hold the number button (in
this example, 1) for more than 2
seconds.
“P1” flashes for a few
seconds.
4 Repeat the above procedure to store
other stations into other preset
numbers.
8
RDS OPERATIONS
To use Network-Tracking Reception, press and
hold TP RDS (Traffic Programme/Radio Data
System) for more than 1 second. Each time you
press and hold the button, Network-Tracking
Reception modes change as follows:
What you can do with RDS EON
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals.For example, the stations send
their station names, as well as information about
what type of programme they broadcast, such as
sports or music, etc.
Mode 1
Mode 2
Mode 3
Another advantage of RDS function is called “EON
(Enhanced Other Networks).” The EON indicator
lights up while receiving an FM station with the EON
data. By using the EON data sent from a station,
you can tune into a different station of a different
network broadcasting your favorite programme or
traffic announcement while listening to another
programme or to another source such as CD.
REG indicator
AF indicator
Mode 1
By receiving the RDS data, this unit can do the
following:
The AF indicator lights up but the REG indicator
does not.
• Tracing the same programme automatically
(Network-Tracking Reception)
Network-Tracking Reception is activated with
Regionalization set to “off.”
• Standby Reception ofTA (Traffic Announcement)
or your favorite programme
• PTY (Programme Type) search
• Programme search
Switches to another station within the same network
when the receiving signals from the current station
become weak.
• And some other functions
•
In this mode, the programme may differ from the one
currently received.
Tracing the same programme
automatically (Network-Tracking
Reception)
Mode 2
Both the AF indicator and the REG indicator light
up.
Network-Tracking Reception is activated with
Regionalization set to “on.”
Switches to another station, within the same
network, broadcasting the same programme when
the receiving signals from the current station
become weak.
When driving in an area where FM reception is not
good, the tuner built in this unit automatically tunes
into another RDS station, broadcasting the same
programme with stronger signals. So, you can
continue to listen to the same programme in its
finest reception, no matter where you drive. (See
the illustration on the next page.)
Mode 3
Two types of the RDS data are used to make
Network-Tracking Reception work correctly — PI
(Programme Identification) and AF (Alternative
Frequency.)
Neither the AF indicator nor the REG indicator lights
up.
Network-Tracking Reception is deactivated.
Without receiving these data correctly from the RDS
station you are listening to, Network-Tracking
Reception will not operate.
9
To deactivate the TA standby mode, press TP
RDS again.
The same programme can be received on
different frequencies.
Programme 1
broadcasting
on frequency A
PTY Standby Reception
Programme 1
broadcasting
on frequency E
When you press PTY while listening to
an FM station, the PTY indicator is lit
during reception of a PTY station and the
PTY standby mode is engaged. The
selected PTY name stored on page 11
flashes for 5 seconds.
Programme 1
broadcasting
on frequency B
•
When the station being received is not a PTY station,
the PTY indicator flashes. Press ¢ or 4
to engage the PTY standby mode. “SEARCH” appears
on the display, and PTY station search starts. When a
PTY station is tuned in, the PTY indicator is lit.
Programme 1
broadcasting
on frequency C
Programme 1
broadcasting
on frequency D
7 If you are listening to a CD and wish to listen to a
selected PTY broadcast, press PTY to enter the
PTY standby mode.(The PTY indicator lights up.)
Using Standby Reception
Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) and Traffic Announcement (TA)
from the current source (another FM station and
CD)
If the selected PTY programme starts broadcasting
while the PTY standby mode is active, the selected
PTY name appears and the playback source
changes to the FM band. The selected PTY
programme can then be heard.
•
Standby Reception will not work if you are listening
to an AM station.
To deactivate the PTY standby mode, press PTY
again.
TA Standby Reception
When you press TP RDS while listening
Selecting your favorite programme for
PTY Standby Reception
to an FM station, the TP indicator is lit
during reception of a TP (Traffic
Programme) station and the TA standby
mode is engaged.
You can select your favorite programme for PTY
Standby Reception to store in memory.
When shipped from the factory, “NEWS” is stored
as the programme type for PTY Standby Reception.
•
When the station being received is not a TP station,
the TP indicator flashes. Press ¢
or 4
to engage the TA standby mode. “SEARCH” appears
on the display, and TP station search starts. When a
TP station is tuned in, the TP indicator is lit.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(PSM: see page 20.)
7 If you are listening to a CD and wish to listen to a
TP station, pressTP RDS to enter theTA standby
mode. (The TP indicator lights up.)
If a traffic programme starts broadcasting while the
TA standby mode is active, “TRAFFIC”appears and
the playback source changes to the FM band.The
volume increases to the presetTA volume level (see
page 13) and the traffic programme can be heard.
10
Searching your favorite programme
2 Select “PTY STBY” (standby) if not
shown on the display.
You can search one of your 6 favorite programme
types stored in memory. When shipped from the
factory, the following 6 programme types have been
stored in the number buttons (1 to 6).
To store your favorite programme types,
see below.
To search your favorite programme type, see
page 12.
3 Select one of twenty-nine PTY codes.
Selected code name appears
on the display and is stored
into memory.
3
1
2
POP M
ROCK M
EASY M
6
4
5
• For details, see the table
below.
CLASSICS
AFFAIRS
VARIED
To store your favorite programme types
4 Finish the setting.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(PSM: see page 20.)
CONTINUED ON THE NEXT PAGE
PTY codes
NEWS:
AFFAIRS:
News
SOCIAL:
Programmes on social
activities
Topical programmes expanding
on current news or affairs
Programmes which impart
advice on a wide variety of
topics
RELIGION:
Programmes dealing with any
aspect of belief or faith, or the
nature of existence or ethics
Programmes where people can
express their views either by
phone or in a public forum
Programmes about travel
destinations, package tours,
and travel ideas and
INFO:
PHONE IN:
TRAVEL:
SPORT:
Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or
regional culture
SCIENCE:
Programmes on natural science
and technology
Other programmes like comedies
or ceremonies
Pop music
Rock music
opportunities
LEISURE:
Programmes concerned with
recreational activities such as
gardening, cooking, fishing,
etc.
Jazz music
Country music
Current popular music from
another nation or region, in that
country’s language
Classic pop music
Folk music
VARIED:
POP M:
ROCK M:
EASY M:
LIGHT M:
JAZZ:
COUNTRY:
NATION M:
Easy-listening music
Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,
the Stock Market, etc.
OLDIES:
FOLK M:
DOCUMENT: Programmes dealing with
factual matters, presented in
an investigative style
CHILDREN: Entertainment programmes for
children
11
2 Select one of PTY codes stored in
2 Select “PTY SRCH” (search) if not
preset number buttons (1 to 6).
shown on the display.
3 Select one of twenty-nine PTY codes.
(See page 11.)
Ex. When “ROCK M” is stored in preset number
button 2
Selected code name appears
on the display.
PTY search for your favorite programme starts
after 5 seconds.
• If the code already stored
in memory is selected, it
will flash on the display.
• If there is a station broadcasting a programme of
the same PTY code you selected, that station is
tuned in.
4 Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset
number you want.
• If there is no station broadcasting a programme
of the same PTY code you selected, the station
will not change.
Note:
In some areas, the PTY search will not work correctly.
The selected code name will flash on
the display.
Other convenient RDS functions
and adjustments
Automatic selection of the station
when using the number buttons
5 Finish the setting.
Usually when you press the number button, the
preset station is tuned in.
However, when the preset station is an RDS station,
something different will happen. If the signals from
that preset station are not sufficient for good
reception, this unit, using the AF data, tunes in
another frequency broadcasting the same
programme as the original preset station is
broadcasting. (Programme search)
To search your favorite programme type
1 Press and hold PTY (programme type)
for more than 1 second while listening
to an FM station.
The last selected PTY code appears.
12
To activate programme search, follow the procedure
below.
• Programme search takes a while.
• See also “Changing the general settings (PSM)”
on page 19.
Setting the TA volume level
You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the preset
level.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
• See also “Changing the general settings (PSM)”
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢
or 4
to select
“P(Programme)-SEARCH.”
3 Rotate the control dial clockwise to select “ON.”
Now programme search is activated.
2 Press ¢
or 4
to select “TA VOL.”
3 Rotate the control dial to set to the desired
volume.
You can set it from “VOL 00” to “VOL 50.”
To cancel programme search, repeat the same
procedure and select “OFF” in step 3 by rotating the
control dial counterclockwise.
Automatic clock adjustment
Changing the display mode while
listening to an FM station
When shipped from the factory, the clock built in
this unit is set to be readjusted automatically using
the CT (Clock Time) data in the RDS signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.
• See also “Changing the general settings (PSM)”
on page 19.
You can change the initial indication on the display
to station name (PS NAME), station frequency
(FREQ) or Clock time (CLOCK) while listening to
an FM RDS station.
• See also “Changing the general settings (PSM)”
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢
or 4
to select “AUTO ADJ.”
3 Rotate the control dial counterclockwise to select
“OFF.”
Now automatic clock adjustment is canceled.
2 Press ¢
or 4
to select “DISPMODE”
(display mode).
3 Rotate the control dial to set to the desired
indication (“PS NAME”, “FREQ” or "CLOCK").
To reactivate clock adjustment, repeat the same
procedure and select “ON” in step 3 by rotating the
control dial clockwise.
Note:
By pressing DISP, you can also change the display while
listening to an FM RDS station.
Each time you press the button, the following information
appears on the display:
Note:
It takes about 2 minutes to adjust the time using the CT
data. So, you should not change the station for more
than 2 minutes continuously; otherwise, the clock time
will not be adjusted.
Station name
(PS NAME)
Station frequency
(FREQ)
CLOCK
(Clock time)
Programme type
(PTY)
•
Then, the display goes back to the original indication
in several seconds.
13
CD OPERATIONS
To stop play and eject the CD
Playing a CD
Press 0.
CD play stops and the CD automatically ejects from
the loading slot.
1 Insert a disc into the loading slot.
The unit turns on,
If you change the source to FM or AM, the CD play
also stops (without ejecting the CD this time).
draws a CD and starts
playback automatically.
Notes:
Note:
• If the ejected disc is not removed for about 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust. (CD play will not
start this time.)
• When a CD is inserted
upside down, the CD
automatically ejects.
• You can eject the CD even when the unit is turned off.
The CD IN indicator lights up.
Total playing time of
the inserted disc
Total track number of
the inserted disc
Current track
Elapsed playing
time
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing CD
turns on the unit and starts playback automatically.
14
Locating a track or a particular Selecting CD playback modes
portion on a CD
To play back tracks at random (Random Play)
You can play back all tracks on the CD at random.
Each time you press MO RND (monaural/random)
To fast-forward or reverse the track
while playing a CD, CD random play mode turns
on and off alternately.
Press and hold ¢
playing a CD, to fast-forward the
track.
, while
Press and hold 4
, while
playing a CD, to reverse the
track.
The RND indicator
To go to the next tracks or the previous
tracks
When the random mode is turned on, the RND
indicator lights up on the display and a track
randomly selected starts playing.
Press ¢
briefly, while
playing a CD, to go ahead to the
beginning of the next track. Each
time you press the button
consecutively, the beginning of
the next tracks is located and
played back.
Press 4
briefly, while
playing a CD, to go back to the
beginning of the current track.
Each time you press the button
consecutively, the beginning of
the previous tracks is located
and played back.
To go to a particular track directly
Press the number button corresponding to the
track number to start its playback.
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.
15
Prohibiting CD ejection
You can prohibit CD ejection and can lock a CD in
the loading slot.
Press and hold CD and 0 for more than 2
seconds.
“EJECT” flashes on the display for about 5
seconds, and the CD is locked and cannot be
ejected.
To cancel the prohibition and unlock the CD,
press and hold CD and 0 again for more than 2
seconds, while pressing CD. “EJECT” appears on
the display, and the CD ejects from the loading slot.
16
SOUND ADJUSTMENTS
2 Adjust the level.
Adjusting the sound
To increase the level.
You can adjust the sound characteristics to your
preference.
1 Select the item you want to adjust.
Each time you press the button, the
adjustable items change as
follows:
To decrease the level.
BAS
FAD
TRE
(bass)
(treble)
(fader)
Equalization pattern changes as you adjust
the bass or treble.
BAL
VOL
LOUD
(balance)
(volume)
(loudness)
Note:
Normally the control dial works for volume
adjustment. So you do not have to select “VOL” to
adjust the volume level.
Indication
To do:
Range
BAS
TRE
FAD*
BAL
Adjust the bass.
–06 (min.)
|
+06 (max.)
Adjust the treble.
–06 (min.)
Using the Sound Control
Memory (SCM)
|
+06 (max.)
Adjust the front
and rear speaker
balance.
R06 (Rear only)
You can select and store a preset sound adjustment
suitable for each playback source.
(Advanced SCM)
|
F06 (Front only)
Adjust the left
and right speaker
balance.
L06 (Left only)
|
Selecting and storing the sound modes
R06 (Right only)
LOUD
Boost low and high
frequencies to
produce a well-
balanced sound
at low volume
level.
Once you select a sound mode, it is stored in
memory. It will be recalled every time you select
the same source and will be shown on the display.
A sound mode can be stored for each of the
following sources — FM1, FM2, FM3, AM and CD.
• If you do not want to store the sound mode
separately for each playback source, but want to
use the same sound mode for all the sources,
see “To cancel Advanced SCM” on page 21.
LOUD ON
|
LOUD OFF
VOL
Adjust the volume. 00 (min.)
|
50 (max.)
* If you are using a two-speaker system, set the fader
level to “00.”
Select the sound mode you want.
Each time you press the button, the
sound mode changes as follows:
BEAT SOFT POP
SCM OFF
17
• When “SCM LINK” is set to “LINK ON”, the
selected sound mode can be stored in memory
for the current source and the effect applies only
to the current source. Each time you change the
playback source, the SCM indicator flashes on
the display.
Storing your own sound
adjustments
You can adjust the sound modes (BEAT, SOFT,
POP) to your preference and store your own
adjustments in memory.
• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
• When “SCM LINK” is set to “LINK OFF”, the
selected sound mode effect applies to any source.
Indication
BEAT
For:
Preset values
BAS
TRE
LOUD
1 Call up the sound mode you want to
adjust.
Rock or disco +02
music
00
ON
• See the left column for details.
SOFT
Quiet
+01
–03
OFF
background
music
2 Select “BAS (Bass),” “TRE (Treble)”
POP
Light music
+04
00
+01
00
OFF
ON
or “LOUD (Loudness).”
SCM OFF (Flat sound)
Recalling the sound modes
When “SCM LINK” is set to “LINK ON,”
Select the source.
3 Adjust the bass or treble level or turn
the loudness function ON/OFF.
• See page 17 for details.
The sound mode stored in memory for the
selected source is recalled.
4 Repeat steps 2 and 3 to adjust the
other items.
5 Press and hold SCM until the sound
mode you have selected in step 1
flashes on the display.
Your adjustment made for the selected
Notes:
sound mode is stored in memory.
• You can adjust each sound mode to your preference,
and store it in memory.
If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments” on
the right column.
• To adjust the bass and treble reinforcement levels or
to turn on/off the loudness function temporarily, see
page 17. (Your adjustments will be canceled if another
source is selected.)
6 Repeat the same procedure to store
other sound modes.
To reset to the factory settings
Repeat the same procedure and reassign the
preset values listed in the table on the left
column.
18
OTHER MAIN FUNCTIONS
Changing the general settings
(PSM)
Setting the clock
You can also set the clock system either 24 hours
or 12 hours.
You can change the items listed on the next page
by using the PSM (Preferred Setting Mode) control.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)
Basic Procedure
1 Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)
2 Set the hour.
1 Select “CLOCK H” if not shown on the
display.
2 Adjust the hour.
2 Select the PSM item you want to
2
1
adjust. (See page 20.)
3 Set the minute.
3 Adjust the PSM item selected above.
1 Select “CLOCK M.”
2 Adjust the minute.
2
1
4 Repeat steps 2 and 3 to adjust the
4 Set the clock system.
1 Select “24H/12H.”
other PSM items if necessary.
2 Select “24H” or “12H.”
2
1
5 Finish the setting.
5 Finish the setting.
To check the current clock time while the unit
is turned off, press DISP (display).
The power turns on, the clock time is shown for
5 seconds, then the power turns off.
19
Preferred Setting Mode (PSM) items
1
2
3
Factory-
preset
settings
See
page
Set.
Counter-
clockwise
Hold.
Select.
Clockwise
Advance
Advance
Back
Back
CLOCK H
CLOCK M
SCM LINK
Hour adjustment
0:00
19
Minute adjustment
Sound control
memory linkage
LINK OFF
12H
LINK ON
24H
LINK ON
24H
18, 21
19
24H/12H
24/12-hour time
display
AUTO ADJ
DISPMODE
Automatic clock
setting
OFF
13
ON
ON
Display mode
FREQ
PS NAME
13
PS NAME
CLOCK
29 programme types
(see page 11.)
PTY STBY
PTY SRCH
TA VOL
PTY standby
PTY search
11
11
NEWS
(See page 11.)
VOL 20
Traffic announcement
volume
VOL 00 – VOL 50
13
13
OFF
ON
OFF
P-SEARCH
LEVEL
Programme search
Level display
AUDIO 2
AUDIO 1
AUDIO 2
21
21
OFF
OFF
MUTING 1
MUTING 2
TEL
Telephone muting
OFF
• Press SEL (select) to finish the setting.
20
To select the telephone muting – TEL
To cancel Advanced SCM – SCM LINK
This mode is used when a cellular phone system is
connected. Depending on the phone system used,
select either “MUTING 1”or “MUTING 2,”whichever
mutes the sounds from this unit.When shipped from
the factory, this mode is deactivated.
You can cancel the Advanced SCM (Sound Control
Memory), and unlink the sound modes and the
playback sources.
When shipped from the factory, a different sound
mode can be stored in memory for each source so
that you can change the sound modes simply by
changing the sources.
• MUTING 1: Select this if this setting can mute
the sounds.
• MUTING 2: Select this if this setting can mute
the sounds.
• LINK ON: Advanced SCM (different sound
modes for different sources)
• OFF:
Cancels the telephone muting.
• LINK OFF: Conventional SCM (one sound
mode for all sources)
To select the level meter – LEVEL
You can select the level display according to your
preference.
When shipped from the factory, “AUDIO 2” is
selected.
• AUDIO 1: Level meter illuminates from bottom
to top.
• AUDIO 2: Alternates level meter (moves from
bottom to top) and illumination
display.
• OFF:
Erases the audio level indicator.
21
Attaching the control panel
Detaching the control panel
1 Insert the left side of the control panel
You can detach the control panel when leaving
the car.
into the groove on the panel holder.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
2 Press the right side of the control
panel to fix it to the panel holder.
1 Unlock the control panel.
2 Pull the control panel out of the unit.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
3 Put the detached control panel into
the provided case.
Connectors
22
REMOTE CONTROLLER
2. Place the battery.
Preparing the remote controller
(With an optionally purchased remote controller)
Slide the battery into the holder with the + side
facing upwards so that the battery is fixed in
the holder.
(only for KD-S811R)
Lithium coin battery
(product number:
CR2025)
We recommend that you use remote controller
RM-RK31 with your unit. The followings are the
instructions for using RM-RK31.
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
3. Return the battery holder.
Insert again the battery holder pushing it until
you hear a clicking sound.
(back side)
Remote sensor
WARNING:
• Do not expose the remote sensor to strong light
(direct sunlight or artificial lighting).
• Store the battery in a place where children cannot
reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble or heat the
battery or dispose it in a fire.
Doing any of these things may cause the battery to
give off heat, crack or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off heat,
crack or start a fire.
• When throwing away or saving the battery, wrap it
in tape and insulate; otherwise, the battery may
start to give off heat, crack or start a fire.
• Do not poke the battery with tweezers or similar
tools.
Installing the battery
When the controllable range or effectiveness of the
remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point pen
or a similar tool.
2) Remove the battery holder.
(back side)
1)
Doing this may cause the battery to give off heat,
crack or start a fire.
2)
23
1 Functions the same as the
button on
Using the remote controller
the main unit.
2 • Functions as the BAND button while listening
to the radio.
Each time you press the button, the band
changes.
• Does not function as the PROG/DISC + button.
3 • Functions as the PRESET button while
listening to the radio.
5
6
1
2
3
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.
7
• Does not function as the DISC – button.
4 Functions the same as the control dial on the
main unit.
4
Note: This button does not function for the preferred
settings mode adjustment.
5 Selects the sound mode.
Each time you press SCM (Sound Control
Memory), the mode changes.
6 Selects the source.
Each time you press FUNC (function), the
source changes.
7 • Searches stations while listening to the radio.
• Fast forwards or reverses the track if pressed
and held while listening to a CD.
• Skips to the beginning of the next tracks or
goes back to the beginning of the current (or
previous tracks) if pressed briefly while
listening to a CD.
24
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
Causes
Remedies
• CD cannot be played back.
CD is inserted upside down.
Insert the CD correctly.
• CD sound is sometimes
interrupted.
You are driving on rough roads.
Stop playing CD while driving
on rough roads.
The disc is scratched.
Change the disc.
Connections are incorrect.
Check the cords and
connections.
Connections are incorrect.
Check the cords and
connections.
• Sound is sometimes
interrupted.
The volume is turned to the
minimum level.
Adjust it to the optimum level.
• Sound cannot be heard from
the speakers.
Connections are incorrect.
Check the cords and
connections.
• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.
Signals are too weak.
Store stations manually.
• Static noise while listening to
the radio.
The antenna is not connected
firmly.
Connect the antenna firmly.
Insert a CD correctly.
• “NO DISC” appears on the
display.
No CD is inserted.
• CD cannot be ejected.
CD is locked.
Unlock the CD (see page 16).
The unit may function
incorrectly.
• CD can be neither played
back nor ejected.
Press and hold both
and 0 at the same time for
several seconds.
Be careful not to drop CD when
it is ejected.
Press and hold both SEL and
at the same time for
The built-in microcomputer may
function incorrectly due to noise,
etc.
• This unit does not work at all.
several seconds to reset the
unit. (The clock setting and
preset stations stored in
memory are erased.) (See
page 2.)
25
MAINTENANCE
Moisture condensation
Handling CDs
Moisture may condense on the lens inside the
CD player in the following cases:
This unit has been designed only to reproduce
the CDs bearing the following marks.
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the CD and leave
the unit turned on for a few hours until the
moisture evaporates.
COMPACT
DIGITAL AUDIO
• Other discs cannot be played back.
Center holder
How to handle CDs
When playing a CD-R (Recordable)
When removing a CD
from its case, press
down the center holder
of the case and lift the
CD out, holding it by the
edges.
You can play back your original CD-Rs on this
receiver.
• Before playing back CD-Rs, read their
instructions or cautions carefully.
• Some CD-Rs recorded on CD recorders may
not be played back on this receiver because of
their disc characteristics, and of the following
reasons:
– Discs are dirty or scratched.
– Moisture condensation occurs on the lens
inside the unit.
• Always hold the CD by the edges. Do not touch
its recording surface.
When storing a CD into its case, gently insert the
CD around the center holder (with the printed
surface facing up).
• Make sure to store CDs into the cases after
use.
– The pickup lens inside the CD player is dirty.
• Use only “finalized” CD-Rs.
• CD-RWs (Rewritable) cannot be played back
on this receiver.
• Do not use CD-Rs with stickers or sticking
labels on the surface. They may cause
malfunctions.
To keep CDs clean
A dirty CD may not play
correctly. If a CD does
become dirty, wipe it with a
soft cloth in a straight line
from center to edge.
CAUTIONS:
To play new CDs
• Do not insert 8 cm CDs (single CDs) into the
loading slot. (Such CDs cannot be ejected.)
• Do not insert any CD of unusual shape — like a
heart or flower; otherwise, it will cause a
malfunction.
• Do not expose CDs to direct sunlight or any heat
source or place them in a place subject to high
temperature and humidity. Do not leave them in
a car.
New CDs may have some
rough spots around the
inner and outer edges. If
such a CD is used, this unit
may reject the CD.
To remove these rough
spots, rub the edges with a
pencil or ball-point pen, etc.
• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean CDs.
About mistracking:
Mistracking may result from driving on extremely
rough roads. This does not damage the unit and the
CD, but will be annoying.
We recommend that you stop CD play while
driving on such rough roads.
26
SPECIFICATIONS
[MW Tuner]
AUDIO AMPLIFIER SECTION
Sensitivity: 20 µV
Selectivity: 35 dB
(For KD-S811R)
Maximum Power Output:
Front:
Rear:
45 W per channel
45 W per channel
[LW Tuner]
Sensitivity: 50 µV
Continuous Power Output (RMS):
Front:
17 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
17 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
CD PLAYER SECTION
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Rear:
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
(For KD-S713R/KD-S711R)
Maximum Power Output:
Dynamic Range:
96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
Front:
Rear:
40 W per channel
40 W per channel
Continuous Power Output (RMS):
Front:
16 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
16 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
GENERAL
Power Requirement:
Rear:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Installation Size: 182 mm × 52 mm × 150 mm
Panel Size: 188 mm × 58 mm × 14 mm
Mass: 1.3 kg (excluding accessories)
Bass:
±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Design and specifications subject to change without
notice.
TUNER SECTION
Frequency Range:
FM:
AM:
87.5 MHz to 108.0 MHz
(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB
27
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Haben Sie PROBLEME mit dem Betrieb?
Bitte setzen Sie Ihr Gerät zurück
Siehe Seite Zurücksetzen des Geräts
Vous avez des PROBLÈMES de fonctionnement?
Réinitialisez votre appareil
Référez-vous à la page intitulée Comment réinitialiser votre appareil
Hebt u PROBLEMEN met de bediening?
Stel het apparaat terug
Zie de pagina met de paragraaf Het apparaat terugstellen
VICTOR COMPANY OF JAPAN, LIMITED
EN, GE, FR, NL
1100HISFLEJES
J
C
V
KD-S811R
KD-S713R
KD-S711R
Installation/ Connection Manual
Einbau/ Anschlußanleitung
Manuel d’installation/ raccordement
GET0013-003A
[E]
1100HISFLEJES
EN, GE, FR
J
C
V
ENGLISH
DEUTSCH
FRANÇAIS
• This unit is designed to operate on 12 V DC, NEGATIVE ground • Dieses Gerät ist für einen Betrieb in elektrischen Anlagen mit • Cet appareil est conçu pour fonctionner sur des sources de
electrical systems.
12 V Gleichstrom und (–) Erdung ausgelegt.
courant continu de 12 V à masse NEGATIVE seulement.
INSTALLATION
EINBAU
INSTALLATION
(IN-DASH MOUNTING)
(IM ARMATURENBRETT)
(MONTAGE DANS LE TABLEAU DE BORD)
• Die folgende Abbildung zeigt einen typischen Einbau. Dennoch • L’illustration suivante est un exemple d’installation typique.
• The following illustration shows a typical installation. However,
you should make adjustments corresponding to your specific
car. If you have any questions or require information regarding
installation kits, consult your JVC IN-CAR ENTERTAINMENT
dealer or a company supplying kits.
müssen Sie entsprechend Ihrem jeweiligen Auto Anpassungen
vornehmen. Bei irgendwelchen Fragen oder wenn Sie
Informationen hinsichtlich des Einbausatzes brauchen, wenden
Sie sich an ihren JVC Autoradiohändler oder ein Unternehmen
das diese Einbausätze vertreibt.
Cependant, vous devez faire les ajustements correspondant à
votre voiture particulière. Si vous avez des questions ou avez
besoin d’information sur des kits d’installation, consulter votre
revendeur d’autoradios JVC ou une compagnie
d’approvisionnement.
1 Before mounting: Press
(Control Panel Release
1 Vor dem Einbau: Drücken Sie
(Freigabe der
1 Avant le montage: Appuyez sur
(déblocage du
panneau de commande) pour éventuellement détacher le
panneau de commande
button) to detach the control panel if already attached.
* When shipped from the factory, the control panel is packed
in the hard case.
Bedienungsblenda), um die Arretierung der
Bedienungsblende zu lösen, sofern diese bereits
angebracht ist.
* Lorsque ce panneau de commande sort d’usine, il est
rangé dans un étui de transport.
* Bei der Auslieferung ab Werk ist die Bedienungsblende
im Etui verpackt.
2 Remove the trim plate.
3 Remove the sleeve after disengaging the sleeve locks.
1 Stand the unit.
2 Retirer la plaque d’assemblage.
3 Libérer les verrous du manchon et retirer le manchon.
1 Poser l’appareil à la verticale.
2 Den Frontrahmen herausnehmen.
3
Die Halterung nach dem Entriegeln der Halterungensperren
abnehmen.
Note: When you stand the unit, be careful not to damage
the fuse on the rear.
Remarque: Lorsque vous mettez l’appareil à la verticale,
faire attention de ne pas endommager le fusible situé
sur l’arrière.
1 Das Gerät aufstellen.
2 Insert the 2 handles between the unit and the sleeve, as
Hinweis: Beim Aufstellen des Geräts darauf achten,
daß die Sicherung auf der Rückseite nicht beschädigt
wird.
illustrated, to disengage the sleeve locks.
2 Insérer les 2 poignées entre l’appareil et le manchon
3 Remove the sleeve.
comme indiqué pour désengagé les verrous de manchon.
2 Die 2 Griffe zwischen dem Gerät und der Halterung wie
abgebildet einstecken und die Halterungensperren
entriegeln.
Note: Be sure to keep the handles for future use after
installing the unit.
3 Retirer le manchon.
Remarque: S’assurer de garder les poignées pour une
utilisation ultérieur, après l’installation de l’appareil.
4 Install the sleeve into the dashboard.
3 Die Halterung entfernen.
* After the sleeve is correctly installed into the dashboard,
bend the appropriate tabs to hold the sleeve firmly in place,
as illustrated.
Hinweis: Sicherstellen, daß die Griffe für künftigen
Gebrauch nach dem Einbau des Geräts aufbewahrt
werden.
4 Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans le tableau
de bord, plier les bonnes pattes pour maintenir fermement
le manchon en place, comme montré.
4 Die Halterung im Armaturenbrett einbauen.
5 Fix the mounting bolt to the rear of the unit’s body and place
the rubber cushion over the end of the bolt.
* Nach dem korrekten Einbau der Halterung im
Armaturenbrett, die entsprechenden Riegel umknicken,
um die Halterung an ihrem Platz zu sichern, siehe
Abbildung.
5 Monter le boulon de montage sur l’arrière du corps de
l’appareil puis passer l’amortisseur en caoutchouc sur
l’extrémité du boulon.
6 Do the required electrical connections.
7 Slide the unit into the sleeve until it is locked.
8 Attach the trim plate so that the projection on the trim plate
5 Die Befestigungsschraube an der Rückseite des
Gerätekörpers befestigen und das Ende der Schraube mit
einem Gummipuffer abdecken.
6 Réalisez les connexions électriques.
is fixed to the left side of the unit.
7 Faire glisser l’appareil dans le manchon jusqu’à ce qu’il soit
9 Attach the control panel.
verrouillé.
6 Nehmen Sie die erforderlichen elektrischen Anschlüsse vor.
7 Das Gerät in die Halterung schieben, bis es einrastet.
8 Befestigen Sie die Frontrahmen in der Form, daß der
Fortsatz der Frontrahmen auf der linken Seite des Geräts
befestigt wird.
8 Attachez la plaque d’assemblage de façon que la projection
de la plaque d'assemblage soit fixée sur le côté gauche de
l’appareil.
9 Remonter le panneau de commande.
9 Die Schalttafel anbringen.
1
2
Dashboard
Armaturenbrett
Tableau de bord
Handle
Griffe
Poignée
3
Rubber cushion
Gummipuffer
Amortisseur en
caoutchouc
184 mm
Lock Plate
Arretierplättchen
Plaque de verrouillage
53 mm
Sleeve
Halterung
Manchon
4
4
Slot
Schlitz
Fente
5
Mounting bolt
Befestigungsschraube
Boulon de montage
7
Fuse
Sicherung
Fusible
6
See “ELECTRICAL CONNECTIONS.”
Siehe „ELEKTRISCHE ANSCHLÜSSE“.
Référez-vous “RACCORDEMENTS
ELECTRIQUES”.
8
*
9
Sleeve
Halterung
Manchon
Trim plate
Frontrahmen
Plaque d’assemblage
• W h e n u sin g th e o p tio n a l sta y
• Be im Ve rw e n d e n d e r An k e r-O p tio n
• Lo rs d e l'u tilisa tio n d u h a u b a n e n o p tio n
• W h e n in sta llin g th e u n it w ith o u t u sin g th e sle e ve
• Be im Ein b a u d e s Ge rä ts o h n e Ha lte ru n g
• Lo rs d e l'in sta lla tio n d e l’a p p a re il sca n s u tilise r d e m a n ch o n
In a Toyota for example, first remove the car radio and install the unit in its place.
Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.
Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.
Fire wall
Feuerwand
Cloison
Flat type screws (M5 x 6 mm)*
* Not included with this unit.
Senkkopfschrauben (M5 x 6 mm)*
Vis à tête plate (M5 x 6 mm)*
* Nicht Teil dieses Geräts.
* Non fourni avec cet appareil.
Stay (option)
Anker (Option)
Hauban (en option)
Washer
Unterlegscheibe
Rondelle
Dashboard
Armaturenbrett
Tableau de bord
Bracket*
Konsole*
Support*
Lock nut
Sicherungsmutter
Ecrou d’arrêt
Screw (option)
Schraube (Option)
Vis (en option)
Pocket
Taschen
Poche
Flat type screws (M5 x 6 mm)*
Senkkopfschrauben (M5 x 6 mm)*
Vis à tête plate (M5 x 6 mm)*
Bracket*
Konsole*
Support*
Mounting bolt
Befestigungsschraube
Boulon de montage
Sleeve
Halterung
Manchon
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
Hinweis: Beim Anbringen des Gerät an der Konsole sicherstellen, daß 6 mm lange Schrauben
verwendet werden. Werden längere Schrauben verwendet, können sie das Gerät beschädigen.
Remarque: Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis
d’une longueur de 6 mm.Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.
Re tra it d e l’a p p a re il
Re m o vin g th e u n it
Au sb a u d e s Ge rä ts
• Avant de retirer l’appareil, libérer la section arrière.
• Before removing the unit, release the rear section.
• Vor dem Ausbau des Geräts den hinteren Teil freigeben.
1 Retirer le panneau de commande.
2 Retirer la plaque d’assemblage.
3 Introduire les deux poignées dans les fentes, comme montré.
Puis, tout en tirant doucement les poignées écartées, faire
glisser l’appareil pour le sortir. (S’assurer de conserver les
poignées après l’installation de l’appareil.)
1 Remove the control panel.
2 Remove the trim plate.
1 Die Schalttafel herausnehmen.
2 Den Frontrahmen abnehmen.
3 Insert the 2 handles into the slots, as shown. Then, while 3 Die 2 Griffe in die Schlitze wie gezeigt stecken. Dann die Griffe
gently pulling the handles away from each other, slide out the
behutsam auseinander ziehen und das Gerät herausziehen.
(Die Griffe nach dem Einbau auf jeden Fall aufbewahren.)
unit. (Be sure to keep the handles after installing it.)
1
2
3
Handle
Griff
Poignée
Control Panel
Trim plate
Schalttafel
Frontrahmen
Panneau de command
Plaque d’assemblage
Liste d e s p iè ce s p o u r l’in sta lla tio n e t
ra cco rd e m e n t
Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.
Te ile liste fü r d e n Ein b a u u n d An sch lu ß
Die folgenden Teile werden zusammen mit diesem Gerät geliefert.
Nach ihrer Überprüfung, die Teile richtig einsetzen.
Pa rts list fo r in sta lla tio n a n d co n n e ctio n
The following parts are provided with this unit.
After checking them, please set them correctly.
Hard case/Control Panel
Etui/Schalttafel
Etui de transport/Panneau de command
Trim plate
Frontrahmen
Plaque d’assemblage
Sleeve
Halterung
Manchon
Power cord
Stromkabel
Cordon d’alimentation
Handles
Griffe
Poignées
Washer (ø5)
Unterlegscheibe(ø5)
Rondelle (ø5)
Lock nut (M5)
Sicherungsmutter (M5)
Ecrou d’arrêt (M5)
Mounting bolt (M5 x 20 mm)
Rubber cushion
Befestigungsschraube (M5 x 20 mm)
Boulon de montage (M5 x 20 mm)
Gummipuffer
Amortisseur en caoutchouc
DEUTSCH
ENGLISH
FRANÇAIS
ELEKTRISCHE ANSCHLÜSSE
ELECTRICAL CONNECTIONS
RACCORDEMENTS ELECTRIQUES
Zur Vermeidung von Kurzschlüssen empfehlen wir, daß Sie den
negativen Batterieanschluß abtrennen und alle elektrischen
Anschlüsse herstellen, bevor das Gerät eingebaut wird. Sind Sie sich
über den richtigen Einbau des Geräts nicht sicher, lassen Sie es von
einem qualifizierten Techniker einbauen.
Pour éviter tout court-circuit, nous vous recommandons de débrancher
la borne négative de la batterie et d’effectuer tous les raccordements
électriques avant d’installer l’appareil. Si l'on n’est pas sûr de pouvoir
installer correctement cet appareil, le faire installer par un technicien
qualifié.
To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections before
installing the unit. If you are not sure how to install this unit correctly,
have it installed by a qualified technician.
Note:
Hinweis:
Remarque:
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems.If your vehicle does not have this system, a voltage
inverter is required, which can be purchased at JVC IN-CAR
ENTERTAINMENT dealers.
Dieses Gerät ist für eine Betrieb in elektrischen Anlagen mit 12 V
Gleichstrom und (–) Erdung ausgelegt. Verfügt Ihr Fahrzeug nicht
über diese Anlage, ist ein Spannungsinverter erforderlich, der bei
JVC Autoradiohändler erworben werden kann.
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce
type d’alimentation, il vous faut un convertisseur de tension, que vous
pouvez acheter chez un revendeur d’autoradios JVC.
• Replace the fuse with one of the specified rating. If the fuse blows
frequently, consult your JVC IN-CAR ENTERTAINMENT dealer.
• If noise is a problem...
• Die Sicherung mit einer der entsprechenden Nennleistung ersetzen.
Brennt die Sicherung häufig durch, wenden Sie sich an ihren JVC
Autoradiohändler.
• Remplacer le fusible par un de la valeur précisée. Si le fusible saute
souvent, consulter votre revendeur d’autoradios JVC.
• Si le bruit est un problème...
This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur. If
this happens, connect the unit’s rear ground terminal (see
connection diagram) to the car’s chassis using shorter and thicker
cords, such as copper braiding or gauge wire. If noise still persists,
consult your JVC IN-CAR ENTERTAINMENT dealer.
• For KD-S811R – Maximum input of the speakers should be more
than 45 W at the rear and 45 W at the front, with an impedance of
4 Ω to 8 Ω.
• For KD-S713R/KD-S711R – Maximum input of the speakers should
be more than 40 W at the rear and 40 W at the front, with an
impedance of 4 Ω to 8 Ω.
• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to touch it
when removing this unit.
• Sind Störgeräusche ein Problem...
Cet appareil incorpore un filtre de bruit dans le circuit d’alimentation.
Cependant, avec certains véhicules, quelques claquements ou
autres bruits non désirés risquent de se produire. Si cela arrive,
raccorder la borne arrière de masse de l’appareil au châssis de la
voiture (voir le diagramme de raccordement) en utiliscant des cordons
les plus gros et les plus courts possibles telle qu'une barre de cuivre
ou une tresse. Si le bruit persiste, consulter votre revendeur
d’autoradios JVC.
Dieses Gerät enthält ein Störfilter im Stromkreis. Bei manchen
Fahrzeugen kann jedoch ein Klicken oder andere unerwünschte
Störgeräusche auftreten. Sollte das der Fall sein, die hintere
Erdungscanschlußklemme (siehe Schaltplan) des Geräts am
Fahrwerk des Fahrzeugs anschließen, dabei kürzere und dickere
Kabel wie beispielsweise Kupfergeflechtdraht oder Stahldraht
verwenden. Bleibt Störgeräusch bestehen, wenden Sie sich an Ihren
JVC Autoradiohändler.
• Pour KD-S811R – La puisscance admissible des haut-parleurs doit
être supérieure à 45 W à l’arrière et à 45 W l’avant, avec une
impédance de 4 Ω à 8 Ω.
• Für KD-S811R – Maximale Eingangsleistung der Lautsprecher muß
höher als 45 W hinten und 45 W vorne sein, mit einer Impedanz von
4 Ω bis 8 Ω.
• Pour KD-S713R/KD-S711R – La puisscance admissible des haut-
parleurs doit être supérieure à 40 W à l’arrière et à 40 W l’avant,
avec une impédance de 4 Ω à 8 Ω.
• Für KD-S713R/KD-S711R – Maximale Eingangsleistung der
Lautsprecher muß höher als 40 W hinten und 40 W vorne sein, mit
einer Impedanz von 4 Ω bis 8 Ω.
• S’assurer de raccorder la mise à la masse de cet appareil au
châssis de la voiture.
• Sicherstellen, daß das Gerät am Fahrwerk geerdet wird.
• Das Abstrahlblech wird nach dem Gebrauch sehr heiß. Beim
Ausbau des Geräts darauf achten, das Abstrahlblech nicht zu
berühren.
• Le dissipateur de chaleur devient très chaud après usage. Faire
attention de ne pas le toucher en retirant cet appareil.
Heat sink
Abstrahlblech
Dissipateur de chaleur
A Ty p ica l Co n n e ctio n s / Ty p isch e An sch lü sse / Ra cco rd e m e n ts ty p iq u e s
Vor dem Anschließen: Die Verdrahtung im Fahrzeug sorgfältig
Avant de commencer la connexion: vérifiez attentivement le
câblage du véhicule. Une connexion incorrecte peut
endommager sérieusement l’appareil.
Before connecting: Check the wiring in the vehicle carefully.
überprüfen. Falsche Anschlüsse können ernsthafte Schäden am
Incorrect connection may cause serious damage to this unit.
Gerät hervorrufen.
1 Connect the colored leads of the power cord to the car
battery, speakers and power aerial (if any) in the following
sequence.
1 Connectez les fils de couleur du cordon d’alimentation à la
batterie de la voiture, aux enceintes et à l’antenne
automatique (s’il y en a une) dans l’ordre suivant.
1 Die farbigen Leitungen des Spannunsgversorgungskabels an
der Autobatterie, den Lautsprechern und dem Motorantenne
(sofern vorhanden) in folgender Reihenfolge anschließen.
1 Black: ground
2 Yellow: to car battery (constant 12 V)
3 Red: to an accessory terminal
4 Blue with white stripe: to power aerial (200 mA max.)
5 Brown: to cellular phone system (For details, refer to
the instructions of the cellular phone.)
6 Others: to speakers
1 Noir: a la masse
1 Schwarz: Erdung
2 Gelb: an Autobatterie (konstant 12 V)
3 Rot: an Zubehöranschlußklemme
4 Blau mit weißem Streifen: an Motorantenne (max. 200 mA)
5 Braun: an Mobiltelefon (Weitere informationen entnehmen
Sie bitte der Bedienungscanleitung des Mobiltelefons.)
6 Andere: an Lautsprecher
2 Jaune: a la batterie de la voiture (12 V constant)
3 Rouge: à la prise accessoire
4 Bleu avec bande blanche: à l’antenne automatique
(200 mA max.)
5 Marron: à un système de téléphone cellulaire (Pour les
détails, se référer aux instructions du téléphone
cellulaire.)
2 Connect the aerial cord.
3 Finally connect the wiring harness to the unit.
2 Das Antennenkabel anschließen.
3 Die Kabelbäume am Gerät anschließen.
Hinweis: Verfügt Ihr Fahrzeug nicht über eine
Zubehöranschlußklemme, die Sicherung von der 1.
Sicherungsposition (Erstposition) in die 2. Sicherungsposition
versetzen, die rote Leitung (A7) an der (+)
6 Autres: aux enceintes
2 Connectez le cordon d’antenne.
3 Finalement, connectez le faisceau de fils à l’appareil.
Note: If your vehicle does not have any accessory terminal,
move the fuse from the fuse position 1 (initial position) to fuse
position 2, and connect the red lead (A7) to the positive (+)
battery terminal.
Remarque: Si votre véhicule ne possède pas de borne
accessoire, déplacez le fusible de la position de fusible 1
(position originale) à la position de fusible 2 et connectez le fil
rouge (A7) à la borne positive (+) de la batterie.
• The yellow lead (A4) is not used in this case.
Batterieanschlußklemme anschließen.
• Die gelbe Leitung (A4) wird in diesem Fall nicht verwendet.
• Le fil jaune (A4) n’est pas utilisé dans ce cas.
ONLY FOR KD-S811R
NUR FÜR KD-S811R
SEULEMENT POUR LE KD-S811R
Fuse position 2
2. Sicherungsposition
Position de fusible 2
B1 B3 B5 B7
B2 B4 B6 B8
A5 A7
Fuse position 1
1. Sicherungsposition
Position de fusible 1
A2 A4 A6 A8
FOR KD-S811R
FÜR KD-S811R
POUR LE KD-S811R
15 A fuse
15 A Sicherung
Fusible 15 A
FOR KD-S713R/KD-S711R
FÜR KD-S713R/KD-S711R
POUR LE KD-S713R/KD-S711R
10 A fuse
B1 B3 B5 B7
B2 B4 B6 B8
A5 A7
1
A8
A2 A4 A6
Rear ground terminal
Hintere
Erdungscanschlußklemme
Borne arrière de masse
10 A Sicherung
Not included with this unit.
Aerial terminal
Antennenanschlußklemme
Borne de l’antenne
*
Ignition switch
Zündschalter
Interrupteur d’allumage
Fusible 10 A
Wird nicht mit Gerät mitgeliefert.
Black
Non fourni avec cet appareil.
*
*
Schwarz
Noir
To metallic body or chassis of the car
Zur metallenen Karosserie oder zum Fahrwerk des
Autos
A8
A4
Line out
(see diagram B )
Schutz kappen
Signalausgang
(siehe Schaltplan B )
Sortie de ligne
1
2
3
2
Vers corps métallique ou châssis de la voiture
Yellow*1
Gelb*1
Jaune*1
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition swich)
Zur einer stromführenden Anschlußklemme im Sicherungsblock zum
Anschließen an die Autobatterie (Umgehen des Zündschalters)
A une borne sous tension du porte-fusible connectée à la batterie de la
voiture (en dérivant l’interrupteur d’allumage)
(voir le diagramme B )
To aerial
Zur Antenne
A l’antenne
Red
Rot
*1: Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
*1: Vor der Überprüfung der Funktionsfähigkeit des Geräts
vor dem Einbau, muß diese Leitung angeschlossen
werden, da sonst die Stromversorgung nicht
eingeschaltet werden kann.
*1: Pour vérifier le fonctionnement de cet appareil avant
installation, ce fil doit être raccordé, sinon l’appareil
ne peut pas être mis sous tension.
Fuse block
Sicherungsblock
Porte-fusible
A7
Rouge
To an accessory terminal in the fuse block
Zur einer Zubehöranschlußklemme im Sicherungsblock
Vers borne accessoire du porte-fusible
3
Blue with white stripe
Blau mit weißem Streifen
Bleu avec bande blanche
A5
To power aerial if any
Zur Motorantenne, sofern vorhanden
Vers l’antenne automatique, s'il y en a une
4
To cellular phone system
Zur Moblitelephon
A2
Brown / Braun / Marron
5
À un système de téléphone cellulaire
B6
B5
B4
B3
B8
B7
B2
B1
6
White with black stripe
Weiß mit schwarzem
Streifen
Gray with black stripe
Grau mit schwarzem
Streifen
Gray
Grau
Gris
Green with black stripe
Grün mit schwarzem
Streifen
Green
Grün
Vert
Purple
Lila
Violet
White
Weiß
Blanc
Purple with black stripe
Lila mit schwarzem Streifen
Violet avec bande noire
Blanc avec bande noire
Gris avec bande noire
Vert avec bande noire
Left speaker (front)
Linker Lautsprecher (vorne)
Enceinte gauche (avant)
Right speaker (front)
Rechter Lautsprecher (vorne)
Enceinte droit (avant)
Left speaker (rear)
Linker Lautsprecher (hinten)
Enceinte gauche (arrière)
Right speaker (rear)
Rechter Lautsprecher
(hinten)
Enceinte droit (arrière)
PRECAUTIO N S o n p o w e r su p p ly a n d sp e a k e r
co n n e ctio n s:
VO RSICHTSMASSREGELN b e im An sch lie ß e n d e r
Stro m ve rso rg u n g u n d La u tsp re ch e r:
PRECAUTIO N S su r l’a lim e n ta tio n e t la
co n n e x io n d e s e n ce in te s:
• DO NOT connect the speaker leads of the power cord to • Die Lautsprecherleitungen des Netzkabels NICHT an der • NE CONNECTEZ PAS les fils d’enceintes du cordon
the car battery; otherwise, the unit will be seriously
damaged.
Autobatterie anschließen, da sonst das Gerät schwer
beschädigt wird.
d’alimentation à la batterie; sinon, l’appareil serait
sérieusement endommagé.
• Connect the black lead (ground), yellow lead (to car battery, • Die schwarze Leitung (Erdung), die gelbe Leitung (zur • Connectez correctement le fil noir (a la masse), le fil jaune (a
constant 12 V), and red lead (to an accessory terminal)
correctly.
Autobatterie, konstant 12 V) und die rote Leitung (zur
Zubehöranschlußklemme) richtig anschließen.
la batterie de la voiture,12 V constant) et le fil rouge (à la prise
accessoire).
• BEFORE connecting the speaker leads of the power cord to • VOR dem Anschließen der Lautsprecherleitungen des • AVANT de connecter les fils d’enceintes du cordon
the speakers, check the speaker wiring in your car.
– If the speaker wiring in your car is as illustrated in Fig. 1
and Fig.2 below, DO NOT connect the unit using that original
speaker wiring. If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect the unit to
the speakers as illustrated in Fig. 3.
– If the speaker wiring in your car is as illustrated in Fig. 3,
you can connect the unit using the original speaker wiring in
your car.
Spannunsgversorgungskabels an die Lautsprecher, die
Lautsprecherverdrahtung in Ihrem Auto überprüfen.
– Ist die Lautsprecherverdrahtung wie unten in “Fig. 1”
und “Fig. 2” abgebildet, das Gerät NICHT mit der
Originalverdrahtung der Lautsprecher anschließen, da
sonst das Gerät schwer beschädigt wird.
Die Lautsprecherverdrahtung erneuern, so daß Sie das Gerät
an den Lautsprechern wie in “Fig. 3” abgebildet anschließen
können.
– Ist die Lautsprecherverdrahtung in Ihrem Auto wie in
“Fig. 3” abgebildet, können Sie das Gerät mit der
Originalverdrahtung der Lautsprecher in Ihrem Auto
anschließen.
– Sind Sie sich über die Lautsprecherverdrahtung in Ihrem Auto
nicht sicher, wenden Sie sich an Ihren Autohändler.
d’alimentation aux enceintes, vérifiez le câblage des enceintes
de votre voiture.
– Si le câblage des enceintes de votre voiture est réalisé
comme montré sur la Fig. 1 ou Fig. 2 ci-dessous, NE
CONNECTEZ PAS l’appareil en utiliscant ce câblage original
d’enceintes. Si vous le faites, l’appareil sera sérieusement
endommagé.
Recommencez le câblage des enceintes de façon que vous
puissiez connecter l’appareil aux enceintes comme montré
sur la Fig. 3.
– Si le câblage des enceintes de votre voiture est comme
montré sur la Fig. 3, vous pouvez connecter l’appareil en
utiliscant ce câblage original d’enceintes pour votre voiture.
– Si vous n’êtes pas sûrs du câblage d’enceintes de votre
voiture, consulter le concessionnaire de votre voiture.
– If you are not sure of the speaker wiring of your car, consult
your car dealer.
+
+
+
-
+
-
L
L
-
+
-
+
-
L
-
+
+
+
-
+
-
R
R
-
+
-
+
-
R
-
Fig. 1
Fig. 2
Fig. 3
Connecting the leads / Anschließen der Leitungen / Raccordement des fils
CAUTION / VORSICHT / PRECAUTION:
• To prevent short-circuit, cover the terminals of the UNUSED leads with
insulating tape.
• Zur Vermeidung eines Kurzschlusses die Anschlußklemmen der NICHT
VERWENDETEN Leitungen mit Isolierklebeband umwickeln.
• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont
PAS utilisés avec de la bande isolante.
Twist the core wires when connecting.
Die Kerndrähte beim Anschließen
verdrehen.
Torsader les âmes des fils en les
Solder the core wires to connect them securely.
Die Kerndrähte anlöten, um sie fest anzuschließen.
Souder les âmes des fils pour les raccorder entre eux
de façon sûre.
raccordant.
B Co n n e ctio n s Ad d in g O th e r Eq u ip m e n t / An sch lü sse zu m Hin zu fü g e n vo n a n d e re r Au srü stu n g / Ra cco rd e m e n t p o u r a jo u te r d ’a u tre s a p p a re ils
Amplifier / Verstärker / Amplificateur
Sie können einen Verstärker anschließen, um Ihre Vous pouvez connecter un amplificateur pour améliorer votre
Autostereoanlage zu erweitern. système autoradio.
• Schließen Sie das Fernbedienungskabel (blau mit weißem • Connectez le fil de commande à distance (bleu avec bande
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
• For amplifier only:
– Connect this unit’s line-out terminals to the amplifier’s line-in
terminals.
– Disconnect the speakers from this unit, connect them
to the amplifier. Leave the speaker leads of this unit
unused. (Cover the terminals of these unused leads with
insulating tape, as illustrated above.)
Streifen) an das Fernbedienungskabel des anderen Geräts an,
so daß es über dieses Gerät gesteuert werden kann.
• Nur für den Verstärker:
blanche) au fil de commande à distance de l’autre appareil de
façon qu’il puisse être commandé via cet appareil.
• Pour l'amplificateur seulement:
– Die Anschlußklemmen am Ausgang dieses Gerät an den
Anschlußklemmen des Eingangs des Verstärkers anschließen.
– Die Lautsprecher von diesem Gerät abtrennen und am
Verstärker anschließen. Die Lautsprecherleitungen dieses
Geräts unbenutzt lassen. (Die Anschlußklemmen dieser
nicht verwendeten Leitungen mit Isolierklebeband
umwickeln, siehe Abbidung oben.)
– Raccorder les bornes de sortie ligne de cet appareil aux bornes
d’entrée ligne de l’amplificateur.
– Déconnectez les enceintes de cet appareil et
connectezles à l’amplificateur. Laissez les fils
d’enceintes de cet appareil inutilisés. (Recouvrir les
extrémités de ces fils inutilisés avec de la bande isolante
comme montré ci-dessus.)
CAUTION / VORSICHT / PRECAUTION:
Rear speakers
Hintere Lautsprecher
Y-connector (not supplied with this unit)
Y-Anschluß (nicht mit diesem Gerät mitgeliefert)
Connecteur Y (non fourni avec cet appareil)
Remote lead
Fernbedienungsleitung
Fil d’alimentation à distance
• To prevent internal heat buildup inside
this unit, place this unit UNDER the
other equipment.
Enceintes arrière
INPUT
JVC Amplifier
• Zur Vermeidung eines Hitzestaus in
diesem Gerät, dieses Gerät UNTER die
andere Geräteansrüstung stellen.
• Pour éviter un échauffement interne de
cet appareil, placez-le SOUS l’autre
appareil.
L
L
JVC Verstärker
JVC Amplificateur
Remote lead (Blue with white stripe)
Fernbedienungsleitung (Blau mit weißem Streifen)
R
R
Fil d’alimentation à distance (Bleu avec bande blanche)
To power aerial if any
Zur Motorantenne, sofern vorhanden
Vers l’antenne automatique, s’il y en a une
Signal cord (not supplied with this unit)
Einzelleitung (nicht mit diesem Gerät mitgeliefert)
Cordon de signal (non fourni avec cet appareil)
LINE OUT
INPUT
JVC Amplifier
JVC Verstärker
Front speakers
Vordere Lautsprecher
Enceintes avant
L
L
L
L
REAR FRONT
R
R
JVC Amplificateur
R
R
KD-S811R
KD-S713R
KD-S711R
ONLY FOR KD-S811R
You can connect another power
amplifier for front speakers.
SOLO PARA KD-S811R
SEULEMENT POUR KD-S811R
Front speakers
Vordere Lautsprecher
Enceintes avant
Podrá conectar otro amplificador
de potencia para los altavoces
delanteros.
Vous pouvez connecter un autre
amplificateur de puissance pour les
enceintes avant.
FEHLERSUCHE
• Die Sicherung brennt durch.
TROUBLESHOOTING
• The fuse blows.
EN CAS DE DIFFICULTÉS
• Le fusible saute.
* Sind die roten und schwarzen Leitungen richtig angeschlossen?
* Are the red and black leads connected correctly?
* Les fils rouge et noir sont-ils racordés correctement?
• Stromversorgung kann nicht eingeschaltet werden.
* Ist die gelbe Leitung angeschlossen?
• Power cannot be turned on.
* Is the yellow lead connected?
• L’appareil ne peut pas être mise sous tension.
* Le fil jaune est-elle raccordée?
• Kein Ton aus den Lautsprechern.
* Ist die Lautsprecherausgangsleitung kurzgeschlossen?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Pas de son des haut-parleurs.
* Le fil de sortie de enceinte est-il court-circuité?
• Ton verzerrt.
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–”terminals of L and R speakers grounded in common?
• Le son est déformé.
* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und rechten
Lautsprecher zusammen geerdet?
* Le fil de sortie de enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–”terminals of L and R speakers grounded in common?
• Gerät wird heiß.
• L’appareil devient chaud.
* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und rechten
Lautsprecher zusammen geerdet?
* Le fil de sortie de enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?
|