CD RECEIVER
KD-S100
KD-S100
KD-S100
RECEPTOR CON CD
RÉCEPTEUR CD
For customer Use:
Enter below the Model No.
and Serial No. which are
located on the top or bottom
of the cabinet. Retain this
information for future
reference.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
Model No.
Serial No.
GET0395-001A
[J]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain
the best possible performance from the unit.
CONTENTS
Control panel .................................
Remote controller — RM-RK300 ..........
5
5
The following marks are used to indicate...
Getting started...............................
7
:
:
:
:
Built-in CD player operations.
External CD changer operations.
SD player operations.
Basic operations.................................................
7
Radio operations ............................
Disc/SD card/USB memory
8
External USB memory operations.
operations ................................... 10
Playing a disc in the unit .................................... 10
Playing discs in the CD changer.......................... 10
Playing from an SD card ..................................... 10
Playing from a USB memory .............................. 11
How to reset your unit
Sound adjustments......................... 14
Activating the Bongiovi Acoustics Digital Power
Station™ ..................................................... 14
Setting the sound modes—SEL......................... 14
• Your preset adjustments will also be erased.
General settings — PSM ................. 15
Title assignment ............................ 19
Satellite radio operations ............... 20
How to forcibly eject a disc
• If an SD card is inserted, eject the SD card first (see
page 10).
iPod /D. player operations ............. 23
®
Other external component operations ... 25
Maintenance .................................. 26
More about this unit ....................... 27
Troubleshooting............................. 30
Specifications................................. 34
1
2
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
• If this does not work, reset your unit.
• Be careful not to drop the disc when it ejects.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
Detaching the control panel
Entering the various menus
The main menu contains four menus (MODE, PSM, SEL,
TITLE).
• If no operation is done for about 15 seconds, menu
screen is canceled.
1
2 Select a menu you want.
Attaching the control panel
Time countdown indicator
3 Enter the selected menu.
• To go back to the previous screen
or exit the MENU screen, press
BACK repeatedly.
Changing the control panel angle
1
2
4 Operate as instructed on the screen.
When using the remote controller
• To go back to the MENU screen, press MENU.
Changing the display information
and patterns
Caution:
Ex.: When tuner is selected as the source
Source operation display
Clock time display
Large graphic display
(full display size)
The unit is equipped with the steering wheel
remote control function.
Small graphic display
Steering wheel
remote input
OE remote adapter
(not supplied)
Steering wheel remote
controller (equipped in the car)
4
Control panel
Parts identification
1
BAND button
9 DISP (display) button
2
3
SOURCE button
• Control dial
p 0 (eject) / (angle) button
q 4 /¢ buttons
• POWER/ATT (attenuator)/ENTER button
MENU button
5 5 (up) / ∞ (down) buttons
w
Remote sensor
4
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BACK button
6
Display window
B (Bongiovi Acoustics Digital Power Station™)
button
e
r
t
7
Reset button
(control panel release) button
8
USB (Universal Serial Bus) input terminal
Remote controller —
RM-RK300
Installing the lithium coin battery
(CR2025)
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material—special
handling may apply.
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Continued on the next page
5
3 5 (up) / ∞ (down) buttons
• For FM/AM: Changes the preset stations.
• For SIRIUS®/XM: Changes the categories.
• For MP3/WMA/SD/USB: Changes the folders.
• While listening to an Apple iPod or a JVC
D. player:
Warning:
• Do not install any battery other than CR2025 or
its equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time; otherwise, it may explode.
• Store the battery in a place where children
cannot reach to avoid risk of accident.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
–Pauses/stops or resumes playback with ∞.
–Enters the main menu with 5.
(Now 5/∞/4/¢ work as the menu
selecting buttons.)*
4
5
VOL (volume) + / – buttons
Adjusts the volume level.
Number buttons
• For FM/AM: Selects the preset station if pressed,
or store a station if pressed and held.
• For SIRIUS®/XM: Selects the preset channels if
pressed, or store a channel if pressed and held.
• For CD/CD Text: Selects the tracks.
• For MP3/WMA/SD/USB: Selects the folders.
• For CD changer: Selects the discs.
ANGLE button
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
6
7
Adjusts the control panel angle.
BAND button
Main elements and features
Selects the band.
8 4 / ¢ buttons
• For FM/AM: Searches for stations if pressed, or
skips frequencies after pressed and held.
• For SIRIUS®/XM: Changes the channels if
pressed briefly, or changes the channels rapidly
if pressed and held.
• For CD/CD Text/MP3/WMA/SD/USB: Changes
the tracks if pressed, or fast-forwards or reverses
the track if pressed and held.
• While listening to an iPod or a D. player (in
menu selecting mode):
–Selects an item if pressed briefly. (Then, press
∞ to confirm the selection.)
–Skips 10 items at a time if pressed and held.
1
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
SOURCE button
* 5 : Returns to the previous menu.
∞ : Confirms the selection.
2
Selects the source.
6
To drop the volume in a
moment (ATT)
Getting started
To restore the sound, press it
again.
Basic operations
~ Turn on the power.
To turn off the power
Ÿ
Setting the clock
FM/AM = SIRIUS*/XM* = CD* =
SD* = USB* = CD-CH*/iPod*/D. player*
(or EXT-IN) = LINE-IN = (back to the
beginning)
• See also “General settings — PSM” on pages
15 – 17.
1 Enter the PSM menu (see page 4).
* You cannot select these sources if they are not
ready or not connected.
2 Set the clock.
!
For FM/AM tuner
1 Select “Clock H” (hour), then adjust the hour.
2 Select “Clock M” (minute), then adjust the
minute.
3 Select “24H/12H,” then “24Hours” or
“12Hours.”
For SIRIUS radio
For XM tuner
3 Finish the procedure.
⁄ Adjust the volume.
To check the current clock time while the
power is turned off
@ Adjust the sound as you want. (See
pages 14 and 15.)
7
4
MO indicator lights up. Reception
improves, but stereo effect will be
lost.
Radio operations
~
Ÿ
To restore the stereo effect, repeat the same
procedure and select “Off” in step 3. The MO indicator
goes off.
! Start searching for a station.
Tuning in to FM stations with
strong signals only—LO (local)/
DX (Distance-Extreme)
Selected band appears.
1 Enter the MODE menu (see page 4).
2
When a station is received, searching stops.
To stop searching, press the same button
again.
3
To tune in to a station manually
In step ! above...
1
4
DX indicator goes off and LO
indicator lights up. Only stations
with sufficient signal strength will be
detected.
2
Select a desired station frequency.
To tune in to all receivable stations, repeat the
same procedure and select “DX” in step 3. The LO
indicator goes off and DX indicator lights up.
When an FM stereo broadcast is hard
to receive
1 Enter the MODE menu (see page 4).
Storing stations in memory
You can preset six stations for each band.
2
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
3
1 Select the FM band (FM1 – FM3) you
want to store into.
8
7 Store the station.
2 Enter the MODE menu (see page 4).
3
When using the remote controller
After tuning in to a station you want to preset...
4
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset
number 4 of the FM1 band.
Listening to a preset station
1
1
2
2
3 Enter the MODE menu (see page 4).
• If you hold down 5/∞, the Preset Station List
appears (go to step 6).
When using the remote controller
Directly select the preset number.
4
5
6 Select a preset number.
• You can move to the lists of the other FM bands
by turning the control dial.
9
Playing from an SD card
Disc/SD card/USB memory
operations
Before detaching the control panel, turn off the power.
~
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
SD loading slot
Ÿ
To stop play and eject the disc
Note:
If a USB memory is attached to the unit, you cannot
eject the disc. “Please Eject USB” flashes on the
display. If this happens, detach the USB memory,
then, press 0 / button again.
SD card
Playing discs in the CD changer
Press in the SD card until you hear a clicking
sound.
All discs in the magazine will be played repeatedly until
you change the source.
• Ejecting the magazine will also stop playback.
To eject the SD card, press the SD card again.
• Press the SD card softly (do not release your
finger quickly); otherwise, the SD card may
pop out from the unit.
* If you have changed the external input setting to
“Ext In” (see page 17), you cannot select the CD
changer.
! Attach the control panel.
10
If an SD card or USB memory has been attached...
⁄
The control panel goes back to
the previous position.
Playback starts automatically if tracks are
recorded.
Playback starts from where it has been stopped
previously.
• If a different SD card or USB memory is currently
attached, playback starts from the beginning.
Playing from a USB memory
This unit can play MP3/WMA tracks stored in a USB
memory.
All tracks in the USB memory will be played repeatedly
until you change the source.
About MP3 and WMA tracks
MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• Removing the USB memory will also stop playback.
About the CD changer
It is recommended to use a JVC MP3-compatible CD
changer with your unit.
• You can also connect MP3-incompatible CD changers.
However, these units are not compatible with MP3
discs.
~
• You cannot use the CH-X99, CH-X100, and KD-MK
series CD changers with this unit.
• You cannot play any WMA disc in the CD changer.
• Disc text information recorded in the CD Text can be
displayed when a JVC CD Text compatible CD changer
is connected.
Ÿ
USB input terminal
To fast-forward or reverse the track
USB memory
To detach the USB memory, straightly pull it out
from the unit.
To go to the next or previous tracks
Cautions:
• Avoid using the SD card/USB memory when it
might hinder your safety driving.
• Make sure all important data have been backed
up to avoid losing the data.
11
To go to the next or previous folders (only for
MP3/WMA/SD/USB)
5 Select a disc/folder/file from the list.
Current folder
For MP3 tracks:
For WMA tracks:
Ex.: When “Folder” is selected
in step 3
Only for MP3/WMA/SD/USB:
If you select the current disc/folder (highlighted on
the screen), its Folder/File List appears.
• Holding the buttons can display the Disc List
6 Starts playback.
(
) and Folder List (
/
/
),
see the following.
Other main functions
When using the remote controller
Selecting a disc/folder/track on the
list
• To directly select a disc (
• To directly select a track of an audio CD or a CD
Text (
• To directly select an MP3/WMA folder
)
)
• This function is not available for an audio CD or a CD
Text when the source is “CD.”
(
/
/
)
To select a number from 1 – 6:
1 Enter the MODE menu (see page 4).
2
To select a number from 7 (1) – 12 (6):
3 Select a list type.
For MP3/WMA folders:
1
*
*
Selectable only when the source is “CD-CH.”
Appears only for MP3/WMA/SD/USB.
It is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
2
4 Confirm the selection.
The selected list appears on the
display.
• You can move to the other list by
turning the control dial.
12
Prohibiting disc ejection
Intro
Plays the beginning 15 seconds of...
You can lock a disc in the loading slot.
Track : All tracks of the current playback media.
[
]
1
Folder*1 : First track of all folders of the current
playback media. [
Disc*2 : First track of all the inserted discs.
]
[
]
2 After making sure “No Eject?” is
Off
: Cancels.
selected...
Repeat Plays repeatedly
“No Eject” flashes, and the disc
cannot be ejected.
Track : The current track. [
]
Folder*1 : All tracks of the current folder. [
]
]
Disc*2 : All tracks of the inserted discs. [
To cancel the prohibition, repeat the same
procedure after making sure “Eject OK?” is selected.
• “Eject OK” flashes on the display.
Off
Random Plays at random
Folder*1 : All tracks of the current folder, then tracks
: Cancels.
of the next folder and so on. [
: All tracks of the current disc. [
: All tracks of the inserted discs/media.
]
]
Selecting the playback modes
Disc
All*3
You can use only one of the following playback modes
at a time.
[
]
Off
: Cancels.
1 Enter the MODE menu (see page 4).
1
*
*
*
Only while playing a media (MP3/WMA/SD/USB).
Only when the source is CD-CH.
2
3
2 Select one of the playback modes.
Only when the source is CD-CH, SD, or USB.
3 Select one of the items (see the following
table).
4 Finish the procedure.
13
Setting the sound modes—SEL
Sound adjustments
You can adjust the sound characteristics to your
preference.
Activating the Bongiovi Acoustics
Digital Power Station
™
~ Enter the SEL menu (see page 4).
The Bongiovi Acoustics Digital Power Station™ is
a digital processing method that maximizes the
frequency response of the speakers, the capability
of the amplifier, and the acoustic properties of your
vehicle’s passenger compartment.
Ÿ Select a setting item.
All vehicles have unique acoustic properties such as
speaker placement and passenger compartment design.
Your car has been custom tuned by Bongiovi Acoustics
engineers to provide the optimum listening experience.
The Bongiovi Acoustics Digital Power Station processing
power produces rich, full sound, and also compensates
for any inherent volume differences that may exist
between audio source or program material.
When selecting “Fad/Bal,” “Bass/Tre,” or
“S.woofer,” press POWER/ATT/ENTER to enter
its submenu.
! Adjust the selected setting item.
(See the following for details.)
• To adjust other SEL settings, press BACK. Then
repeat steps Ÿ and !.
Studio Quality Digital Sound
Optimum speaker frequency response
⁄ Finish the procedure.
+
Optimum power distribution from amplifier
+
Custom tuned listening environment
To adjust fader and balance—
Fad/Bal
• Fad (fader)
To enjoy the Bongiovi Acoustics Digital Power
Station’s Studio Quality Digital Sound that has
been custom tuned for your vehicle:
Adjust the front and rear speaker balance.
• Bal (balance)
To deactivate the Bongiovi Acoustics Digital
Adjust the left and right speaker balance.
Power Station™, press the button again.
14
To adjust bass and treble—Bass/Tre
Select “Bass” or “Treble.”
To adjust the input level of each
source—Vol Adj
1
2
This setting is required for each source except for FM.
Once an adjustment is made, it will be memorized.
When you change the source, the volume level will
automatically increase or decrease according to the
adjusted level.
Adjust the bass or treble.
1
2
Select a source before entering the SEL menu.
Adjust to match the input level to the FM sound
level.
To adjust subwoofer output—
S.woofer
1
2
3
Adjust the output level.
General settings — PSM
You can change PSM (Preferred Setting Mode) items
Select a cut-off frequency according to the
connected subwoofer.
(except “Sirius ID”) listed in the table that follows.
1 Enter the PSM menu (see page 4).
2 Select a PSM item.
Adjust the continuity of the sound among speakers
(slope).
3 Select or adjust the selected PSM item.
4 Repeat steps 2 and 3 to adjust the other
PSM items if necessary.
5 Finish the procedure.
Continued on the next page
15
Indications
Items
Settings, [reference page]
(
: Initial)
Anime
Animation
• On
:
An animation screen appears when you turn on or off the
power, change the source, and when you select MENU.
Cancels.
• Off
:
:
Clock H
Hour adjustment
1 – 12 (0 – 23)
[Initial: 1 (1:00AM)]
See also page 7 for setting.
See also page 7 for setting.
See also page 7 for setting.
Clock M
Minute adjustment
00 – 59
[Initial: 00 (1:00AM)]
:
:
:
24H/12H
Time display mode
Clock Adj *1
Time display mode
• 12Hours
• 24Hours
• Auto
The built-in clock is automatically adjusted using the clock data
provided via the satellite radio channel.
Cancels.
• Off
:
:
Time Zone *1,
*
• Eastern
• Atlantic
• Newfndlnd
• Alaska
Select your residential area from one of the following time
zones for clock adjustment.
2
• Pacific
• Mountain
• Central
DST *1
• On
:
Activates daylight savings time if your residential area is
Daylight savings time
subject to DST.
Cancels.
• Off
:
:
Sirius ID *3
—
Your SIRIUS identification number appears on the display, [20].
Scroll *4
• Once
• Auto
• Off
:
:
:
Scrolls the track information once.
Repeats scrolling (at 5-second intervals).
Cancels.
• Pressing DISP for more than one second can scroll the display
regardless of the setting.
Dimmer
• Auto
• Time Set
:
:
Dims the display when you turn on the headlights.
Sets the timer for dimmer, see page 18 for setting.
From: Any hour; To: Any hour
• Off
• On
:
:
Cancels.
Activates dimmer. (Does not work if “Bright” is set to “1.”)
Bright
Display brightness
1 – 10 [Initial: 8]
:
Adjust the display contrast to make the display indications
clear and legible. (If Dimmer is set to “On”, selecting “1” to “4”
takes no effect.)
16
Indications
Items
Settings, [reference page]
(
: Initial)
ID3 Tag
Tag display
• On
• Off
:
:
Shows the Tag information while playing MP3/WMA tracks.
Cancels.
Theme
Display theme
• Large
:
Select the display theme for large graphic display, [4]. See page
18 for setting.
Select the display theme for small graphic display, [4]. See page
18 for setting.
(1 [Initial] or 2)
• Small
(1 [Initial] or 2)
:
IF Band
Intermediate frequency
band
• Auto
:
:
Increases the tuner selectivity to reduce interference noises
between close stations. (Stereo effect may be lost.)
Subject to interference noises from adjacent stations, but sound
quality will not be degraded and the stereo effect will remain.
• Wide
Area
• US
• SA
• EU
:
:
:
When using in North/Central/South America. AM/FM intervals
are set to 10 kHz/200 kHz.
When using in South American countries where FM interval is
100 kHz. AM interval is set to 10 kHz.
When using in any other areas. AM/FM intervals are set to
9 kHz/50 kHz (100 kHz during auto search).
Tuner channel interval
Beep
Key-touch tone
• On
• Off
:
:
Activates the key-touch tone.
Deactivates the key-touch tone.
Ext In *5
External input
• Changer
:
To use a JVC CD changer, [10], a JVC compatible satellite (SIRIUS/
XM) tuner, [20], or an Apple iPod or a JVC D. player, [23].
To use any other external component than the above, [25].
• Ext In
:
:
Tel
• Muting 1/
Select either one which mutes the sounds while using a cellular
Telephone muting
Muting 2
phone.
• If CD/CD-CH/SD/USB/iPod/D. player has been selected as the
source, playback pauses during telephone muting.
Cancels.
• Off
:
Amp Gain
Amplifier gain control • Low PWR
• High PWR
:
:
Volume 00 – Volume 50
Volume 00 – Volume 30 (Select this if the maximum power of
the speaker is less than 50 W to avoid damaging the speakers.)
Deactivates the built-in amplifier.
• Off
:
1
*
*
*
*
*
Displayed only when SIRIUS Satellite radio or XM Satellite radio is connected.
Displayed only when “Clock Adj” is set to “Auto.”
Displayed only when SIRIUS Satellite radio is connected.
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
Displayed only when one of the following sources is selected—FM, AM, CD, SD, USB, or LINE-IN.
2
3
4
5
17
Selecting timer for the dimmer
Selecting the graphic theme
You can dim the display at night or as you set the timer.
You can select the graphic theme for large and small
display sizes (see also page 4).
1 Select “Dimmer” from the PSM menu.
1 Select “Theme” from the PSM menu.
2 Select “Time Set.”
2 Select the size of the display.
3 Adjust the dimmer time.
1 Set the dimmer start time.
24Hours: [0 – 23]
3 Select the theme.
12Hours: [1A (1AM) – 12A (12AM);
1P (1PM) – 12P (12PM)]
4 Repeat steps 2 and 3 to select the other
display size and theme.
5 Finish the procedure.
2 Set the dimmer end time.
24Hours: [0 – 23]
12Hours: [1A (1AM) – 12A (12AM);
1P (1PM) – 12P (12PM)]
To show the selected display theme, press DISP
repeatedly while playing a source.
4 Finish the procedure.
18
3
4
Move to the next (or previous) character
position.
Title assignment
You can assign titles to station frequencies, CDs (both
in this unit and in the CD changer) and the external
components (LINE-IN and EXT-IN).
Repeat steps 1 to 3 until you finish entering
the title.
Sources
Maximum number of characters
Station
Up to 16 characters (up to 30 station
4 Finish the procedure.
• To cancel the title entry without
registration, press MENU.
frequencies frequencies including both FM and AM)
CDs/CD-CH* Up to 32 characters (up to 30 discs)
External
Up to 16 characters
component
* You cannot assign names to any discs other than
conventional CDs.
Available characters
In addition to the Roman alphabets (A – Z, a – z),
the following characters will be used.
1 Select the sources.
• For FM/AM tuner: Select a station.
• For CDs in this unit: Insert a CD.
• For CDs in the CD changer: Select “CD-CH,” then
select a disc number.
Accented letters: upper case
Accented letters: lower case
Numbers and symbols
• For external component: Select “LINE-IN” or
“EXT-IN.”
2 Enter the TITLE menu (see page 4).
3 Assign a title.
1
Select a character set.
A (A – Z: upper case) = a (a – z: lower case)
= 0 (numbers and symbols) = Á (Accented
letters: upper case) = á (Accented letters:
lower case) = (back to the beginning)
To erase the entire title
2
Select a character.
In step 3...
19
Activate your SIRIUS subscription after
connection:
1
Satellite radio operations
This unit is satellite (SAT) Radio Ready—compatible
with both SIRIUS Satellite radio and XM Satellite radio.
Before operating your satellite radio, refer also to the
Instructions supplied with your SIRIUS Satellite radio or
XM Satellite radio.
2
JVC DLP starts updating all the SIRIUS channels.
Once completed, JVC DLP tunes in to the preset
channel, CH184.
• “SIRIUS” and the SIRIUS dog logo are registered
trademarks of SIRIUS Satellite Radio Inc.
• XM and its corresponding logos are registered
trademarks of XM Satellite Radio Inc.
• “SAT Radio,” the SAT Radio logo and all related marks
are trademarks of SIRIUS Satellite Radio Inc., and XM
Satellite Radio, Inc.
3
4
Check your SIRIUS ID, see page 16.
Contact SIRIUS on the internet at
activate your subscription, or you can call
SIRIUS toll-free at 1-888-539-SIRIUS (7474).
“Subscription Updated Press Any Key to Continue”
appears on the display once subscription has been
completed.
Listening to the satellite radio
Connect either one of the following (separately
purchased) to the CD changer jack on the rear of this
unit.
• JVC SIRIUS radio DLP—Down Link Processor, for
listening to the SIRIUS Satellite radio.
• XMDirectTM Universal Tuner Box—Using a JVC
Smart Digital Adapter (XMDJVC100: not supplied), for
listening to the XM Satellite radio.
Activate your XM subscription after
connection:
• Only Channel 0, 1, and 247 are available before
activation.
1
GCI (Global Control Information) update:
• If channels are updated after subscription, updating
starts automatically.
2
The following appears and no sound can be heard.
– For SIRIUS Satellite radio: “Channels Updating
XX%* Completed”
– For XM Satellite radio: “UPDATING”
• Update takes a few minutes to complete.
• During update, you cannot operate your satellite
radio.
TM
XMDirect Universal Tuner Box starts updating
all the XM channels. “Channel 1” is tuned in
automatically.
3
Check your XM Satellite radio ID labelled on
the casing of the XMDirectTM Universal Tuner
Box, or tune in to “Channel 0” (see page 22).
* Changes every 20% of update is completion, (ex. 20%,
40%, 60%).
20
4
Contact XM Satellite radio on the internet
activate your subscription, or you can call
1-800-XM-RADIO (1-800-967-2346).
Listening to the XM Satellite radio
1
2
Once completed, the unit tunes in to one of
the available channels (Channel 4 or higher).
3 Select a channel for listening.
• Holding the button changes the
Listening to the SIRIUS Satellite radio
channels rapidly.
1
2
Searching for category/channel
You can search for programs by category (Category
Search) or channel number (Channel Search).
• In Category Search, you can tune in to the channels
of the selected category. Category Search begins from
the currently selected channel.
3 Select a category.
You can tune in to all the channels of every
category by selecting “ALL.”
• In Channel Search, you can tune in to all channels
(including non-categorised channels).
Selecting a particular category (SPORTS,
ENTERTAINMENT, etc.) allows you to enjoy only the
channels from the selected category.
• Holding either of the buttons can display the
category list (see page 22).
1 Select a category (Category Search).
• For Channel Search, skip this
step.
4 Select a channel for listening.
2 Select a channel for listening.
• Holding the button changes the
channels rapidly.
• When changing the category or channel, invalid and
unsubscribed channels are skipped.
If no operation is done for about 15 seconds,
Category Search is canceled.
In Channel Search, channel name and channel
number appear on the display during search.
• While searching, invalid and unsubscribed channels
are skipped.
21
Checking the XM Satellite radio ID
While selecting “XM1,” “XM2,” or “XM3,” select
“Channel 0.”
6 Select a user preset number.
• You can move to the lists of the other SIRIUS bands by
turning the control dial.
The display alternately shows “RADIO ID” and the
8-digit (alphanumeric) ID number.
7 Store the channel.
To cancel the ID number display, select any channel
other than “Channel 0.”
Storing user channels in memory
Listening to a user preset channel
You can preset six channels for each band.
1
2
Ex.: Storing a SIRIUS channel into preset number 4 of
the SR1 band.
1
2
• Holding this button displays the User Preset
Channel List (see step 6 above).
3 Perform steps 3 to 6 (on the left column)
to select a user preset channel.
• Holding the button displays the User Preset
Channel List (see step 6 on the right column).
4 Finish the procedure.
3 Enter the MODE menu (see page 4).
4 Select “Preset.”
Selecting a category/channel on the
list
5
Selecting a category from the list
1 Enter the MODE menu (see page 4).
2 Select “Category.”
22
3
5 Finish the procedure.
4 Select a category you want.
To change the display information while
listening to a channel
• You can move to the other lists by turning the
control dial.
Category name and channel name = Artist/
composer* name and song/program name =
Clock = Small graphic display = Large
graphic display = (back to the beginning)
5 Finish the procedure.
The first channel of the selected
category is tuned in.
* Only for SIRIUS Satellite radio.
• If you select the current category (highlighted on
the display), its channel list appears.
iPod /D. player
operations
®
Holding 5/∞ also shows the Category List while
listening to a channel.
This unit is ready for operating an Apple iPod or a JVC
D. player from the control panel.
Selecting a channel from the list
1 Enter the MODE menu (see page 4).
Before operating your iPod or D. player:
• Connect either one of the following (separately
purchased) to the CD changer jack on the rear of this
unit.
2 Select “Channel.”
– Interface adapter for iPod , KS-PD100, for
®
controlling an iPod.
– D. player interface adapter, KS-PD500, for
controlling a D. player.
3
• Refer also to the manual supplied with the interface
adapter for details.
4 Select a channel you want.
Caution:
Make sure to turn off this unit or turn off the
vehicle’s ignition switch before connecting or
disconnecting the iPod or D. player.
• You can move to the other lists by turning the
control dial.
Continued on the next page
23
Preparations:
Make sure “Changer” is selected for the external input
setting, see page 17.
Selecting a track from the menu
1 Enter the main menu.
Now the 5/∞/4 /¢
buttons work as the menu selecting
buttons*.
~
Ÿ
* The menu selecting mode will be canceled:
– If no operations are done for about 5 seconds.
– When you confirm the selection of a track.
Playback starts automatically from where it has
been paused*1 or stopped*2 previously.
2 Select the desired menu.
! Adjust the volume.
For iPod:
Playlists Ô Artists Ô Albums Ô Songs
Ô Genres Ô Composers Ô (back to the
beginning)
For D. player:
Playlist Ô Artist Ô Album Ô Genre Ô
⁄ Adjust the sound as you want. (See
pages 14 and 15.)
• Make sure the equalizer on the iPod or
D. player is deactivated.
Track Ô (back to the beginning)
To pause*1 or stop*2
playback
3 Confirm the selection.
• To move back to the previous
menu, press 5.
To resume playback, press it
again.
To fast-forward or
reverse the track
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
To go to the next or
previous tracks
• Holding 4 /¢ can skip 10 items at
a time.
1
*
*
For iPod
For D. player
2
24
Selecting the playback modes
Other external component
operations
1 Enter the MODE menu (see page 4).
You can connect an external component to the LINE IN
plugs on the rear or to the CD changer jack on the rear
using the Line Input Adapter—KS-U57 (not supplied)
or AUX Input Adapter—KS-U58 (not supplied).
2 Select one of the playback modes.
3 Select an item (see table below).
4 Finish the procedure.
• For listening to the SD card/USB memory, see pages
10 – 13; For iPod, or D.player, see pages 23 – 25.
~
LINE-IN : For selecting the external component
connected to the LINE IN plugs.
EXT-IN : For selecting the external component
connected to the CD changer jack.
If “EXT-IN” does not appear, see page 17 and
select the external input (“Ext In”).
Repeat play
One
: Functions the same as “Repeat One” of
the iPod or “Repeat Mode = One” for the
D. player.
Ÿ Turn on the connected component
and start playing the source.
All
: Functions the same as “Repeat All” of
the iPod or “Repeat Mode = All” for the
D. player.
! Adjust the volume.
Off
: Cancels.
Random play
Album* : Functions the same as “Shuffle Albums”
of the iPod.
Song/On : Functions the same as “Shuffle Songs” of
the iPod or “Random Play = On” of the
D. player.
⁄ Adjust the sound as you want. (See
pages 14 and 15.)
Off
: Cancels.
* For iPod: Only if you select “All” in “Albums” of the
main “MENU.”
25
To keep discs clean
Maintenance
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvent (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
Connector
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture evaporates.
How to handle SD card
SD cards are precision products. DO NOT impact, bend,
drop, or wet them.
Do not use the following discs:
Warped disc
How to handle discs
Center holder
When removing a disc from its
case, press down the center holder
of the case and lift the disc out,
holding it by the edges.
Sticker
Sticker residue
Stick-on label
• Always hold the disc by the edges. Do not touch its
recording surface.
When storing a disc into its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs into the cases after use.
26
Inserting a disc
More about this unit
Basic operations
Turning on the power
• By pressing SOURCE on the unit, you can also turn on
the power. If the source is ready, playback also starts.
• When a disc is inserted upside down, the control
panel moves down, and the disc automatically ejects
from the loading slot.
• If you keep the control panel open for about
1 minute, (beeps sound when the “Beep” setting is
turned “On”—see page 17) the control panel returns
to its previous position.
• Do not insert 8 cm discs (single CD) and unusual
shape discs (heart, flower, etc.) into the loading slot.
Turning off the power
• If you turn off the power while listening to a disc, disc
play will start from where playback has been stopped
previously, next time you turn on the power.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play back only files of the same type
which are first detected if a disc includes both audio
CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
–Discs are dirty or scratched.
–Moisture condensation occurs on the lens inside the
unit.
–The pickup lens inside the unit is dirty.
–CD-R/CD-RW on which the files are written with
“Packet Write” method.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and
stations are stored newly.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc/SD card/USB memory operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
–There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
• Do not use the following CD-Rs or CD-RWs:
–Discs with stickers, labels, or protective seal stuck to
the surface.
General
• This unit has been designed to reproduce CDs/CD
Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable)
in audio CD (CD-DA) and MP3/WMA format; MP3/
WMA files recorded in an SD card or a USB memory.
• While playing an audio CD: If a title has been
assigned to the audio CD (see page 19), it will be
shown on the display.
–Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperatures or high
humidities may cause malfunctions or damage to the
unit.
• While fast-forwarding or reversing an MP3/WMA
track, you can only hear intermittent sounds.
Continued on the next page
27
Playing an MP3/WMA discs
Playing MP3/WMA tracks from an SD card or
a USB memory
• While playing from an SD card or a USB memory, the
playback order may differ from other players.
• This unit may be unable to play back some SD cards
or USB memories due to their characteristics or
recording conditions.
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3/WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files compliant to
ISO 9660 Level 1/Level 2, Romeo, Joliet, Windows
long file name.
• The maximum number of characters for file/folder
names vary among the disc format used (includes 4
extension characters—<.mp3> or <.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo*: up to 128 (72) characters
• Depending on the shape of the USB memories and
connection ports, some USB memories may not be
attached properly or the connection might be loose.
• It is not recommended to use a USB memory wider
than 20 mm as it will block you from pressing some
buttons on the control panel.
• If the connected USB memory does not have the
correct files, “No Files” appears and the unit returns
to the previous source.
• This unit can show Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3/WMA files.
– Joliet*: up to 64 (36) characters
– Windows long file name*: up to 128 (72)
characters
• This unit can play back MP3 files recorded in VBR
(variable bit rate).
• For SD card: The maximum number of characters
for folder name is 8 characters; file names is 12
characters. This unit cannot recognize folder with
period (.) on the folder name.
For USB memory: The maximum number of
characters for folder and file names is 25 characters;
128 characters for MP3/WMA tag information.
• For SD card: This unit can recognize a total of 255 files
and 63 folders.
For USB memory: This unit can recognize a total of
2 500 files and 250 folders (999 files per folder).
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
* The parenthetic figure is the maximum number of
characters for file/folder names in case the total
number of files and folders is 313 or more.
• This unit can play back the files recorded in VBR
(variable bit rate).
Files recorded in VBR have a discrepancy in elapsed
time display, and do not show the actual elapsed
time. Especially, after performing the search function,
this difference becomes noticeable.
• This unit can recognize a total of 512 files, of 200
folders, and of 8 hierarchies.
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media Audio.
– WMA files copy-protected with DRM.
– Files which have the data such as WAVE, ATRAC3,
®
Media Audio.
®
– WMA files copy-protected with DRM.
– Files which have the data such as WAVE, ATRAC3,
etc.
etc.
• The search function works but search speed is not
constant.
• The search function works but search speed is not
constant.
28
Changing the source
Satellite radio operations
• If you change the source, playback also stops.
Next time you select the same source again, playback
starts from where it has been stopped previously.
• You can also connect the JVC SIRIUS radio PnP
(Plug and Play), using the JVC SIRIUS radio adapter,
KS-U100K (not supplied) to the CD changer jack on
the rear.
By turning on/off the power of the unit, you can turn
on/off the JVC PnP. However, you cannot control it
from this unit.
• To know more about SIRIUS Satellite radio or to sign
up, visit <http://www.sirius.com>.
• For the latest channel listings and programming
information, or to sign up for XM Satellite radio, visit
<http://www.xmradio.com>.
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust. (Disc will not play
this time.)
Sound adjustments
Setting the sound modes—SEL
iPod or D. player operations
• When you turn on this unit, the iPod or D. player is
charged through this unit.
• While the iPod or D. player is connected, all
operations from the iPod or D. player are disabled.
Perform all operations from this unit.
• The text information may not be displayed correctly.
– Some characters such as accented letters cannot be
shown correctly on the display.
– Depends on the condition of communication
between the iPod or D. player and the unit.
• If the text information includes more than 16
characters, it scrolls on the display (see also page 16).
This unit can display up to 40 characters.
• If you are using a two-speaker system, set the fader
level to the center.
• Subwoofer out setting takes effect only when a
subwoofer is connected.
• You cannot change the input level—“VolAdjust” of
the FM stations. If the source is FM, “Fix” will appear
when you try to adjust it.
General settings — PSM
• “Auto Dimmer” may not work correctly on some
vehicles, particularly on those having a control dial
for dimming. In this case, change the “Dimmer”
setting to any one other than “Auto.”
• If you change the “Amp Gain” setting from “High
PWR” to “Low PWR” while the volume level is set
higher than “Volume 30,” the unit automatically
changes the volume level to “Volume 30.”
Notice:
When operating an iPod or a D. player, some
operations may not be performed correctly or as
intended. In this case, visit the following JVC web
site:
For iPod users: <http://www.jvc.co.jp/english/
car/support/ks-pd100/index.html>
Title assignment
• If you try to assign titles to more than 30 station
frequencies or 30 discs, “Name Full” appears. Delete
unwanted titles before assignment.
• Titles assigned to discs in the CD changer can also be
shown if you play back the disc in the unit and vice
versa.
For D. player users: <http://www.jvc.co.jp/
english/car/support/ks-pd500/index.html>
29
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• “Connect Error” appears on the display.
Remove the control panel, wipe the connector, then attach
it again (see pages 4 and 26).
• “Push Reset” appears on the display and the Reset the unit (see page 3). If this does not work, check the
control panel movement is freezed.
• SSM automatic presetting does not work.
• Static noise while listening to the radio.
• Disc cannot be played back.
installation.
Store stations manually.
Connect the antenna firmly.
Insert the disc correctly.
• Insert a finalized CD-R/CD-RW.
• CD-R/CD-RW cannot be played back.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can be neither played back nor ejected. • Unlock the disc (see page 13).
• Eject the disc forcibly (see page 3).
• Disc cannot be recognized (“No Disc,”
“Loading Error,” or “Eject Error” appears).
Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in the format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the file
names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or WMA
tracks.)
• A longer readout time is required (“File
Check” keeps flashing on the display).
Do not use too many hierarchies and folders.
30
Symptoms
Remedies/Causes
• Tracks do not play back in the order you have Playback order is determined when the files are recorded.
intended them to play.
• Elapsed playing time is not correct.
This sometimes occurs while playing. This is caused by
how the tracks are recorded on the disc.
• “No Files” appears on the display.
Insert a disc that contains MP3/WMA tracks.
• “Not Support” appears on the display and
track skips.
Skip to the next track encoded in an appropriate format
or to the next non-copy-protected WMA track.
• “No Music” appears on the display.
Change the disc that contains MP3/WMA tracks.
• Correct characters are not displayed (e.g.
album name).
This unit can only display letters (capital: A – Z, small:
a – z), numbers, and a limited number of symbols and
special characters (see page 19).
• Noise is generated.
The track played back is not an MP3/WMA track. Skip to
another file. (Do not add the extension code <.mp3> or
<.wma> to non-MP3 or WMA tracks.)
• “File Check” keeps flashing on the display.
• “No Files” appears on the display.
• Readout time varies depending on the device.
• Do not use too many hierarchy and folders.
• Turn off the power then on again.
Play a device that contains tracks encoded in an
appropriate format.
• “Not Support” appears on the display and
track skips.
The track is unplayable.
• “Read Failed” appears on the display, then
returns to the previous source.
• The device may be malfunctioning, or may not have
been formatted correctly.
The files included in the device are corrupted.
• Do not pull out or attach the USB memory repeatedly
while “File Check” appears on the display.
• “SD Loading Error” appears on the display
while playing tracks from an SD card.
Detach the control panel and reinsert the SD card. The
control panel goes back to initial position (Angle 1).
• While playing a track, sound is sometimes
interrupted.
MP3/WMA tracks have not been properly copied into the
device.
Copy MP3/WMA tracks again into the device, and try
again.
• Correct characters are not displayed (e.g.
album name).
This unit can only display letters (capital: A – Z, small:
a – z), numbers, and a limited number of symbols and
special characters (see page 19).
Continued on the next page
31
Symptoms
Remedies/Causes
• “No Disc” appears on the display.
• “No Magazine” appears on the display.
• “Reset 8” appears on the display.
Insert a disc into the magazine.
Insert the magazine.
Connect this unit and the CD changer correctly and press
the reset button of the CD changer.
• “Reset 1” – “Reset 7” appears on the display. Press the reset button of the CD changer.
• The CD changer does not work at all.
Reset the unit (see page 3).
• “CALL 1-888-539-SIRIUS TO SUBSCRIBE”
scrolls on the display while listening to the
SIRIUS Satellite radio.
Starts subscribing SIRIUS Satellite radio (see page 20).
• No sound can be heard. “Channel Updating
XX%* Completed” appears on the display.
The unit is updating the channel information and it takes a
few minutes to complete.
• Either “No Signal” or “NO SIGNAL” appears
on the display.
Move to an area where signals are stronger.
• Either “No Antenna” or “CHECK ANTENNA”
appears on the display.
Connect the antenna firmly.
• “Invalid Channel” appears on the display for No broadcast on the selected channel.
about 5 seconds, then returns to the previous Select another channel or continue listening to the
display while listening to the SIRIUS Satellite previous channel.
radio.
• “No Name” appears or scrolls on the display No text information for the selected channel.
while listening to the SIRIUS Satellite radio.
• “---” appears on the display while listening
to the XM Satellite radio.
• “---” appears on the display for about
2 seconds, then returns to the previous
channel while listening to the XM Satellite
radio.
Selected channel is no longer available or is unauthorized.
Select another channel or continue listening to the
previous channel.
• “OFF AIR” appears on the display while
listening to the XM Satellite radio.
Selected channel is not broadcasting at this time.
• “LOADING” appears on the display while
listening to the XM Satellite radio.
Select another channel or continue listening to the
previous channel.
• “Reset 08” appears on the display.
The unit is loading the channel information and audio. Text
information are temporarily unavailable.
• Satellite radio does not work at all.
Reconnect this unit and the satellite radio correctly and
reset this unit.
* Changes every 20% of update is completion, (ex. 20%, 40%, 60%).
32
Symptoms
Remedies/Causes
• The iPod or D. player does not turn on or
does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• Buttons do not work as intended.
• The sound is distorted.
The functions of the buttons have been changed. Press
POWER/ATT/ENTER before performing the operation.
Deactivate the equalizer either on the unit or the iPod/
D. player.
• “Disconnect” appears on the display.
• Playback stops.
Check the connecting cable and its connection.
The headphones are disconnected during playback. Restart
the playback operation using the control panel (see page
24).
• No sound can be heard when connecting an Disconnect the headphones from the iPod nano.
iPod nano.
• No sound can be heard.
• “ERROR 01” appears on the display when
connecting a D. player.
Disconnect the adapter from the D. player. Then, connect
it again.
• “No Files” or “No Track” appears on the
display.
No tracks are stored. Import tracks to the iPod or D. player.
• “Reset 1” – “Reset 7” appears on the display. Disconnect the adapter from both the unit and iPod/
D. player. Then, connect it again.
• “Reset 8” appears on the display.
Check the connection between the adapter and this unit.
• The iPod’s or D. player’s controls do not work Reset the iPod or D. player.
after disconnecting from this unit.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
• SD logo is a trademark.
• iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
33
Specifications
Power Output:
20 W RMS × 4 Channels at 4 Ω and
≤ 1% THD+N
Signal to Noise Ratio: 80 dBA (reference: 1 W into 4 Ω)
Load Impedance:
Tone Control Range: Bass:
Tre:
4 Ω (4 Ω to 8 Ω allowance)
+6 dB/–10 dB at 30 Hz
+6 dB/–10 dB at 12 kHz
40 Hz to 20 000 Hz
Frequency Response:
Level/Impedance:
Line-In:
Line-Out:
1.5 V/20 kΩ load (full scale)
5.0 V/20 kΩ load (full scale)
1 kΩ
Output Impedance:
Subwoofer-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Other Terminals:
Frequency Range:
LINE IN, CD changer, Steering wheel remote input
FM:
87.5 MHz to 107.9 MHz
(with channel interval set to 200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM:
530 kHz to 1 710 kHz
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
FM Tuner
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response:
Stereo Separation:
40 Hz to 15 000 Hz
35 dB
AM Tuner
Type:
Sensitivity/Selectivity:
Compact disc player
20 μV/65 dB
Signal Detection
System:
Non-contact optical pickup (semiconductor laser)
Number of Channels:
Frequency Response:
Wow and Flutter:
MP3:
2 channels (stereo)
5 Hz to 20 000 Hz
Less than measurable limit
32 kbps – 320 kbps
Bit Rate:
Sampling Frequency:
MPEG-1: 48 kHz, 44.1 kHz, 33 kHz
MPEG-2: 24 kHz, 22.05 kHz, 16 kHz
8 kbps – 320 kbps
WMA:
Bit Rate:
Sampling Frequency:
48 kHz, 44.1 kHz, 32 kHz
34
Format:
FAT 12/16
Storage:
8 MB – 512 MB
Playable Audio Format:
MP3:
MP3/WMA
8 kbps – 320 kbps
Bit Rate:
Sampling Frequency:
MPEG-1: 48 kHz, 44.1 kHz, 33 kHz
MPEG-2: 24 kHz, 22.05 kHz, 16 kHz
8 kbps – 192 kbps
WMA:
Bit Rate:
Sampling Frequency:
48 kHz, 44.1 kHz, 32 kHz
FAT 12/16/32
Format:
Storage:
Less than 4 GB (1 partition type)
MP3/WMA
Less than 500 mA
Playable Audio Format:
Max. Current:
MP3:
Bit Rate:
32 kbps – 320 kbps
Sampling Frequency:
MPEG-1: 48 kHz, 44.1 kHz, 32 kHz
MPEG-2: 24 kHz, 22.05 kHz, 16 kHz
MPEG-2.5: 12 kHz, 11.025 kHz, 8 kHz
5 kbps – 320 kbps
WMA:
Bit Rate:
Sampling Frequency:
Operating Voltage:
8 kHz – 48 kHz
DC 14.4 V (11 V to 16 V allowance)
Negative ground
Power Requirement:
Grounding System:
Allowable Operating Temperature:
Dimensions (W × H × D): Installation Size (approx.):
0°C to +40°C (32°F to 104°F)
182 mm × 52 mm × 162 mm
"
"
"
(7-3/16 × 2-1/16 × 6-7/16 )
188 mm × 58 mm × 11 mm
Panel Size (approx.):
"
"
"
(7-7/16 × 2-5/16 × 7/16 )
Mass (approx.):
1.7 kg (3.8 lbs) (excluding accessories)
Design and specifications are subject to change without notice.
If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.
35
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Still having trouble??
USA ONLY
Call 1-800-252-5722
We can help you!
EN, SP, FR
0906DTSMDTJEIN
© 2006 Victor Company of Japan, Limited
|