MICRO COMPONENT SYSTEM
UX-H35— ConsistsofCA-UXH35andSP-UXH35
UX-H33— ConsistsofCA-UXH33andSP-UXH33
UX-H30— ConsistsofCA-UXH30andSP-UXH30
MICRO COMPONENT SYSTEM
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0101-008A
[B]
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards, but like any electrical equip-
ment, care must be taken if you are to obtain the best results and safety is to be assured.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of
equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains
plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way
—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended
operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It
is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case—this
could result in a fatal electrical shock.
— NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1
2
3
Front:
No obstructions and open spacing.
Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
Bottom:
Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
15 cm
Front View
15 cm
Side View
15 cm
1 cm
1 cm
15 cm
UX-H35
UX-H33
UX-H30
15 cm
10 cm
UX-H35/UX-H33/UX-H30
G-2
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain
the best possible performance from your unit, and retain this manual for future
reference.
Power sources
• When unplugging the unit from the wall outlet,
About This Manual
always pull on the plug, not the AC power cord.
This manual is organized as follows:
• The manual mainly explains operations using the
buttons on the remote control.
DO NOT handle the AC power cord with
wet hands.
You can use the buttons both on the remote
control and on the main unit for the same
operations if they have the same or similar names
(or marks), unless mentioned otherwise.
• Basic and common information that is the same for
many functions is grouped in one place, and is not
repeated for each procedure. For instance, we do not
repeat the information about turning on/off the unit,
setting the volume, changing the sound effects, and
others, which are explained in the section “Common
Operations” on pages 10 and 11.
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm
place
Should condensation occur, the unit may malfunction.
In this case, leave the unit turned on for a few hours
until the moisture evaporates, unplug the AC power
cord, then plug it in again.
• The following symbols are used in this manual:
Gives you warning and caution to
prevent damage or risk of fire/electric
shock.
Furthermore, it gives you information
about what is not good for obtaining
the best possible performance from the
unit.
Others
• Should any metallic object or liquid fall into the unit,
unplug the power cord and consult your dealer
before operating any further.
• If you are not going to operate the unit for an
extended period of time, unplug the power cord.
Gives you information and hints you
should know.
DO NOT disassemble the unit since there
are no user serviceable parts inside.
Precautions
If anything goes wrong, unplug the power cord and
consult your dealer.
Installation
• Install in a place which is level, dry and neither too
hot nor too cold—between 5˚C and 35˚C.
• Install the unit in a location with adequate
ventilation to prevent internal heat buildup in the
unit.
• Leave sufficient distance between the unit and the
TV.
• Keep the speakers away from the TV to avoid
interference with TV.
DO NOT install the unit in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or vibration.
1
Contents
Location of the Buttons ............................................... 3
Main Unit .......................................................................... 3
Remote Control ................................................................. 5
Getting Started............................................................. 6
Supplied Accessories ......................................................... 6
Connecting Antennas ........................................................ 6
Connecting Speakers ......................................................... 7
Connecting Other Equipment............................................ 8
Putting the Batteries into the Remote Control .................. 9
Common Operations ................................................. 10
Setting the Clock ............................................................. 10
Turning On the Power ..................................................... 11
Adjusting the Volume ...................................................... 11
Adjusting the Tone (Bass/Treble).................................... 11
Reinforcing the Bass Sound ............................................ 11
Listening to FM and AM (MW) Broadcasts ........... 12
Tuning in to a Station ...................................................... 12
Presetting Stations ........................................................... 12
Tuning in to a Preset Station ........................................... 13
Receiving FM Stations with RDS ................................... 13
Changing the RDS Information ...................................... 14
Searching for Programs by PTY Codes (PTY Search) ... 14
Switching Temporarily to a Program Type
of Your Choice .......................................................... 15
Playing Back Discs..................................................... 16
Playing Back the Entire Disc—Normal Play .................. 16
Basic Disc Operations ..................................................... 17
Programming the Playing Order of the Tracks
—Program Play......................................................... 17
Playing at Random—Random Play ................................ 18
Repeating Tracks—Repeat Play...................................... 18
Playing Back Tapes .................................................... 19
Playing Back a Tape ........................................................ 19
Recording ................................................................... 20
Recording on a Tape ........................................................ 20
Disc Direct Recording ..................................................... 21
One Track Recording ...................................................... 21
Using the Timers ........................................................ 22
Using Daily Timer and Recording Timer ........................ 22
Using Snooze Timer ........................................................ 24
Using Sleep Timer ........................................................... 24
Maintenance ............................................................... 25
Troubleshooting ......................................................... 26
Additional Information ............................................. 27
Specifications.............................................................. 28
2
Location of the Buttons
Become familiar with the buttons on your unit.
Main Unit
Top view
PHONES
1
2
COMPACT
7
8
DIGITAL AUDIO
3
4
TIMER/SNOOZE
OPEN
9
p
MULTI CONTROL
ONE TOUCH
REC
AHB PRO
VOLUME
4
¢
7
BAND
5
6
AUX
TAPE
TUNER
CD
Front view
q
w
STANDBY
r
MICRO COMPONENT SYSTEM
e
t
3
Continued
Display window
1
2
3
4
5
6
7
8
BASS SLEEP SNOOZE
STEREO
REC ON
OFF CLOCK
RDS TA NEWS INFO
9
p
MONO
REC
q
w
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PROGRAM RANDOM
ALL
OVER
e
r
t
y
See the pages in parentheses for details.
Main unit
Display window
1 PHONES jack (11)
2 Disc cover
1 Tape operation indicators
REC
• 2 3 (tape direction),
(reverse mode)
(recording), and
3 TIMER/SNOOZE button (10, 22 – 24)
4 ONE TOUCH REC (recording) button (20, 21)
(standby/on) button (11, 23)
6 Source buttons
2
(timer) indicator
5
3 REC (recording timer) indicator
4 ON/OFF (timer on-time/off-time) indicators
5 CLOCK indicator
6
7
8
• AUX, @ # TAPE, BAND TUNER, and
#/8 CD
Pressing one of these buttons also turns on the
unit.
BASS
indicator
SLEEP
indicator
SNOOZE
indicator
7 MULTI CONTROL buttons
• 4 (reverse skip), 7 (stop), and ¢ (forward
skip)
8 AHB (Active Hyper Bass) PRO button (11)
9 0 OPEN (disc cover open) button (16)
p VOLUME + / – buttons (11)
q Display window
9 MONO and STEREO indicators
p RDS operation indicators
• RDS and TA/NEWS/INFO
q Main display
• Shows the source name, frequency, etc.
w Track calender indicators
e PROGRAM indicator
r RANDOM indicator
w STANDBY lamp (11)
e Cassette holder
t Repeat indicators
r Remote sensor
•
and ALL
t ) (cassette holder open) button (19 – 21)
y OVER indicator
4
Remote Control
See the pages in parentheses for details.
1 Number buttons
2 BASS button (11)
3 Multi control buttons
STANDBY/ON
DISPLAY
•
UP, 4 (reverse skip), 7 (stop), ¢
(forward skip), and DOWN
1
4
3
2
5
8
9
p
q
w
e
4 SET button (13)
5 Source buttons
6
• 3/8 CD, 2 3 TAPE, TUNER, and AUX
Pressing one of these buttons also turns on the
unit.
1
CLOCK
/TIMER
7
9
10
10
SLEEP
6 REV.MODE (reverse mode) button (19 – 21)
7 PRGM (program) button (17)
8 RDS operation buttons (14, 15)
• PTY SEARCH, PTY SELECT + / –, DISPLAY,
and TA/NEWS/INFO
UP
BASS
TREBLE
2
3
SET
4
9 STANDBY/ON
p DISPLAY button (10)
q CLOCK/TIMER button (10, 22, 23)
w SLEEP button (24)
button (11, 23)
CANCEL
DOWN
r
TUNER
AUX
CD
TAPE
5
AUTO
e TREBLE button (11)
REV.MODE FM MODE PRESET
r CANCEL button (18)
t
y
u
i
o
6
7
t AUTO PRESET button (12)
y FM MODE button (12)
u REPEAT button (18)
i RANDOM button (18)
o AHB (Active Hyper Bass) PRO button (11)
; VOLUME + / – button (11)
PRGM
RANDOM REPEAT
AHB PRO
PTY
SEARCH
PTY
SELECT DISPLAY
8
TA/NEWS
+
/INFO
;
–
VOLUME
STANDBY
MICRO COMPONENT SYSTEM
When using the remote control, point it at the
remote sensor on the front panel.
5
Getting Started
Continued
To connect an outdoor FM antenna
Before connecting the antenna, disconnect the supplied
FM antenna.
Supplied Accessories
Make sure that you have all the following items.
The number in parentheses indicates the quantity of
each piece supplied.
• AM loop antenna (1)
• FM antenna (1)
Outdoor FM antenna
(not supplied)
• AC power cord (1)
• Remote control (1)
• Batteries (2)
Coaxial cable (not supplied)
If anything is missing, consult your dealer
immediately.
Connecting Antennas
FM antenna
A 75 Ω antenna with coaxial type connector
(IEC or DIN 45325) should be used.
FM antenna (supplied)
1 Attach the FM antenna to the FM
COAXIAL 75 Ω terminal.
2 Extend the FM antenna.
3 Fasten it up in the position which gives
you the best reception, then fix it on the
wall, etc.
About the supplied FM antenna
The FM antenna supplied with this unit can be used as
temporary measure. If reception is poor, you can connect an
outdoor FM antenna.
6
AM (MW) antenna
Connecting Speakers
1
1
2
Vinyl-covered wire
(not supplied)
Speaker cord
Speaker cord
2
AM loop antenna
(supplied)
Right speaker
Left speaker
1 Connect the AM loop antenna to the
1 Press and hold the clamp of the
speaker terminal on the rear of the
unit.
AM LOOP terminals as illustrated.
2 Turn the AM loop antenna until you
have the best reception.
2 Insert the end of the speaker cord into
the terminal.
Match the polarity between the unit and the
speaker terminals: ª to ª and · to ·.
To connect an outdoor AM (MW) antenna
When reception is poor, connect a single vinyl-covered
wire to the AM EXT terminal and extend it
horizontally. The AM loop antenna must remain
connected.
3 Release your finger from the clamp.
• DO NOT connect speakers while the
power is on.
• DO NOT connect more than one speaker
to each speaker teminal.
For better reception of both FM and AM (MW)
Make sure the antenna conductors do not touch any other
terminals and connecting cords.
•
•
Keep the antennas away from metallic parts of the unit,
connecting cords, and the power cord.
IMPORTANT: Use only speakers with the same
speaker impedance as shown on the speaker
terminals on the rear of the unit.
7
Continued
To remove the speaker grilles
The speaker grilles are removable.
NOW you are ready to plug in the unit
and any other connected equipment.
IMPORTANT: Be sure to check all connections to
Projections
be done before plugging the power cord.
Holes
This unit can be supplied with power through the AC
IN connector (at home) or the DC IN connector (in a
car).
• Do not connect the unit using the AC IN connector
and the DC IN connector at the same time for safe
and correct use.
Speaker grille
To connect the AC power cord
To remove the speaker grille, insert your fingers at
the top of the speaker grille, pull towards you. Then
pull the bottom towards you.
AC power cord (supplied)
AC IN
To attach the speaker grille, follow the illustration
above.
Connect the AC power cord to the AC IN connector
and a wall outlet.
Connecting Other Equipment
To connect an audio equipment
You can connect audio equipment—used only as a
playback device.
• DO NOT connect any equipment while
the power is on.
• DO NOT plug in any equipment until all
connections are complete.
Be sure that the plugs of the audio cords are colored:
White plugs and jacks are for left audio signals, and
red ones for right audio signals.
R
L
L
Audio equipment
R
To audio output
For playing other equipment through this unit,
connect between the audio output jacks on the other
equipment and AUX jacks by using audio cords (not
supplied).
8
When using the unit in your car
Putting the Batteries into the Remote
Control
To car’s cigarette
lighter socket (12 V)
Insert the batteries—R6(SUM-3)/AA(15F)—into the
remote control, by matching the polarity (+ and –) on
the batteries with the + and – markings on the battery
compartment.
When the remote control can no longer operate the
unit, replace both batteries at the same time.
1
12V 4A
DC IN
Car adapter
(JVC model: CA-R120E)
R6(SUM-3)/AA(15F)
2
Connect a car adapter to the DC IN (12 V, 4 A)
connector and the cigarette lighter socket.
• DO NOT connect the car adapter to the
cigarette lighter socket before connecting
it to the DC IN connector. Otherwise, a
short-circuit may occur if the adapter plug
makes contact with any metal part inside
the car.
3
• DO NOT use this unit for a long time in a
car while the car ignition switch is turned
“OFF” (or set to “ACC”). Otherwise, the
car battery will be exhausted.
• DO NOT use an old battery together with
a new one.
• DO NOT use different types of batteries
together.
• DO NOT expose batteries to heat or
flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to
use the remote control for an extended
period of time. Otherwise, the remote
control will be damaged from battery
leakage.
9
Common Operations
Continued
Setting the Clock
3 Press ¢ or 4 to adjust the minute,
then press TIMER/SNOOZE.
Before operating the unit any further, first set the unit’s
clock. When you plug in the power cord, the CLOCK
indicator and “0:00” start flashing on the display.
You can set the clock whether the unit is on or off.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 1.
To check the clock time during play
On the remote control ONLY:
DISPLAY
Press DISPLAY (grey-colored).
• Each time you press the button, the
source indication and the clock time
alternate on the display.
On the remote control:
CLOCK
1 Press CLOCK/TIMER.
The hour digits start flashing on the
display.
/ TIMER
•
•
When you unplug the power cord or if a power failure
occurs
The clock is reset to “0:00” right away. If this happens, set
the clock again.
CLOCK
The clock may gain or lose 1 to 2 minutes per month
If this happens, reset the clock.
UP
2 Press UP or DOWN to
adjust the hour, then press
CLOCK/TIMER.
DOWN
To change the clock
The minute digits start flashing.
1
Make sure the
the display.
(timer) indicator is not lit on
• If it is lit, press and hold CLOCK/TIMER (or
TIMER/SNOOZE on the unit) until it goes off.
CLOCK
CLOCK
/ TIMER
2
Press CLOCK/TIMER (or TIMER/SNOOZE
on the unit) repeatedly until the unit enters the
clock setting mode (the hour digits start flashing
on the display).
3 Press UP or DOWN to adjust the
minute, then press CLOCK/TIMER.
First time you press CLOCK/TIMER (or TIMER/
SNOOZE on the unit), the unit enters the timer
setting mode. (See page 22.)
CLOCK
3
4
Repeat steps 2 and 3 of the procedure of
“Setting the Clock.”
Press and hold CLOCK/TIMER (or TIMER/
SNOOZE on the unit) again so that the
(timer) indicator goes off.
On the unit:
TIMER/SNOOZE
1 Press TIMER/SNOOZE.
The hour digits start flashing on
the display.
2 Press ¢ or 4 to
adjust the hour, then
press TIMER/SNOOZE.
The minute digits start flashing.
TIMER/SNOOZE
10
Turning On the Power
Adjusting the Tone (Bass/Treble)
STANDBY/ON
To turn on the unit, press
You can adjust the bass level (low frequency range)
and the treble level (high frequency range) within a
range of –5 to +5.
When shipped, the bass level set to “BASS 0” and the
treble level set to “TREBLE +1.”
STANDBY/ON
(
on the unit).
The STANDBY lamp on the unit goes off.
• When you press the source button
—3/8 CD, 2 3 TAPE, TUNER (or
BAND TUNER on the unit) and AUX, the unit
automatically turns on and starts playback if the
source is ready.
• This function only affects the playback sound, and
does not affect your recording.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 1.
To turn off the unit (standby), press
STANDBY/ON
(
on the unit) again.
The STANDBY lamp on the unit lights on.
• The CLOCK indicator and “0:00” flash on the
display until you set the built-in clock. After setting
the clock, the clock time will appear on the display
while the unit is on standby.
On the remote control ONLY:
1 Press BASS to adjust the bass level or
press TREBLE to adjust the treble
level.
BASS
TREBLE
• A little power is always consumed even while the
unit is on standby.
To switch off the power supply completely, unplug
UP
the power cord.
2 Press
level or press
decrease it.
UP to increase the
DOWN to
DOWN
When you unplug the power cord or if a power
failure occurs
The clock is reset to “0:00” right away, while the tuner preset
stations (see page 12) will be erased in a few days.
Reinforcing the Bass Sound
You can reinforce the bass sound to maintain rich, full
bass at low volume—Active Hyper Bass Pro.
• This function only affects the playback sound, and
does not affect your recording.
Adjusting the Volume
You can adjust the volume level only while the unit is
turned on. The volume level can be adjusted between
“VOL MIN” and “VOLUME 1” – “VOLUME 40
(VOL MAX).”
AHB PRO
To get the effect, press AHB PRO so
BASS
that the
display.
indicator lights up on the
• Each time you press the button, the
bass reinforcement alternates between on (AHB ON)
and off (AHB OFF).
Press VOLUME + to increase the
volume or press VOLUME – to
decrease it.
To cancel the effect, press AHB PRO again so that the
VOLUME
For private listening
BASS
indicator goes off.
Connect headphones to the PHONES jack. No sound comes
out of the speakers. Be sure to turn down the volume before
connecting or putting on headphones.
DO NOT turn the unit off (standby) with the
volume set to an extremely high level;
otherwise, the sudden blast of sound can
damage your hearing, speakers and/or
headphones when you turn on the unit or
start playing any source next time.
REMEMBER you cannot adjust the volume
level while the unit is on standby.
11
Listening to FM and AM (MW) Broadcasts
Continued
Tuning in to a Station
Presetting Stations
You can preset 30 FM and 15 AM (MW) stations—
using either automatic presetting or manual presetting.
In some cases, test frequencies have been already
memorized for the tuner since the factory examined the
tuner preset function before shipment. This is not a
malfunction.
TUNER
1 Press TUNER (or BAND
TUNER on the unit) to select
the band.
The unit automatically turns on and
tunes in to the previously received
station—either FM or AM (MW).
• Each time you press the button, the
band alternates between FM and AM
(MW).
BAND
TUNER
To preset stations automatically—Automatic
presetting
You need to preset stations separately for the FM and
AM (MW) bands.
On the remote control ONLY:
2 Press and hold ¢ or
4 for more than 1
second.
TUNER
1 Press TUNER to select the
band.
The unit automatically turns on and
tunes in to the previously received
station—either FM or AM (MW).
• Each time you press the button, the band
alternates between FM and AM (MW).
The unit starts searching for
stations and stops when a station of sufficient
signal strength is tuned in.
• If a program is broadcast in stereo, the
STEREO indicator lights up.
AUTO
PRESET
2 Press and hold AUTO
To stop searching, press ¢ or 4.
PRESET for more than 2
seconds.
Local stations with strong signals are
searched for and stored in memory automatically.
When automatic presetting is over, the station
stored in preset number 1 is tuned in.
• Storing new stations erase the previously stored
one.
When you press ¢ or 4 briefly and
repeatedly
The frequency changes step by step.
To change the FM reception mode
On the remote control ONLY:
3 Repeat steps 1 and 2 to store stations
FM MODE
When an FM stereo broadcast is hard to
receive or noisy, press FM MODE so that
the MONO indicator lights up on the
display. Reception will improve.
for the other band.
When you cannot automatically store stations
you want
Stations with weak signals cannot be detected with automatic
presetting. To store such stations, use manual presetting.
To restore the stereo effect, press FM MODE again
so that the MONO indicator goes off. In stereo mode,
you can hear stereo sound when a stereo program is
broadcast.
12
To preset stations manually—Manual presetting
You need to preset stations separately for the FM and
AM (MW) bands.
To tune in to a preset station directly using the
number buttons
On the remote control ONLY:
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 2.
1
4
3
2
5
8
Pressing the number button(s)
allows you to select the preset
number you want.
Ex.: For preset number 5, press 5.
For preset number 15, press
+10, then 5.
6
7
9
On the remote control ONLY:
10
10
1 Tune in to the station you want to
preset.
For preset number 20, press
+10, then 10.
• See “Tuning in to a Station” on page 12.
For preset number 30, press
+10, +10, then 10.
SET
2 Press SET.
Receiving FM Stations with RDS
UP
RDS (Radio Data System) allows FM stations to send
an additional signal along with their regular program
signals. For example, the stations send their station
names, as well as information about what type of
program they broadcast, such as sports or music, etc.
When tuned in to an FM station which provides the
RDS service, the RDS indicator lights up on the
display.
3 Press
UP or
DOWN
to select a preset number.
DOWN
4 Press SET again.
With the unit, you can receive the following types of
RDS signals.
The tuned station in step 1 is stored in the preset
number selected in step 3.
• Storing a new station on a used number erases
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
the previously stored one.
Shows types of broadcast programs.
RT (Radio Text):
When you unplug the power cord or if a power
failure occurs
Shows text messages the station sends.
Enhanced Other Networks:
The tuner preset stations will be erased in a few days. If this
happens, preset the stations again.
Provides information about the types of the
programs sent by other RDS stations.
Tuning in to a Preset Station
More about RDS
On the remote control ONLY:
•
•
Some FM stations do not provide RDS signals.
RDS services vary among FM RDS stations. For details on
RDS services in your area, check with local radio stations.
RDS may not work correctly if the received station is not
transmitting the signals properly or if the signal strength is
weak.
TUNER
1 Press TUNER to select the
band.
•
The unit automatically turns on
and tunes in to the previously
received station—either FM or AM (MW).
• Each time you press the button, the band
alternates between FM and AM (MW).
UP
2 Press
UP or
DOWN
to select a preset number.
DOWN
13
Continued
On the remote control ONLY:
Changing the RDS Information
PTY
SEARCH
1 Press PTY SEARCH.
You can see RDS information on the display while
listening to an FM station.
“PTY” and “SELECT” appear on the
display alternately.
On the remote control ONLY:
PTY
SELECT
2 Press PTY SELECT + or
PTY SELECT – until the
PTY code you want
DISPLAY
Press DISPLAY (orange-colored).
• Each time you press the button, the
display changes to show the following
information:
appears on the display.
• Each time you press the buttons,
the PTY codes change as follows:
PS
PTY
RT
(Program Service) (Program Type)
(Radio Text)
NONE Ô NEWS Ô AFFAIRS Ô
INFO Ô SPORT Ô EDUCATE Ô
DRAMA Ô CULTURE Ô SCIENCE Ô
VARIED Ô POP M Ô ROCK M Ô
EASY M Ô LIGHT M Ô CLASSICS Ô
OTHER M Ô WEATHER Ô
FINANCE Ô CHILDREN Ô SOCIAL Ô
RELIGION Ô PHONE IN Ô TRAVEL Ô
LEISURE Ô JAZZ Ô COUNTRY Ô
NATION M Ô OLDIES Ô FOLK M Ô
DOCUMENT Ô TEST Ô ALARM Ô
(back to the beginning)
Station frequency
(or preset channel no.)
•
•
If no PS, PTY, or RT signals are sent by a station
“NO PS,” “NO PTY,” or “NO RT” appears on the display.
On the characters displayed
When the display shows PS, PTY or RT signals:
– The display shows upper case letters only.
– The display cannot show accented letters; for example,
“A” may represent accented “A’s” like “Á, Â, Ã, À, Ä
and Å.”
3 Press PTY SEARCH once again.
While searching, “SEARCH” and the selected PTY
code alternately appear on the display.
The unit searches 30 preset FM stations, stops
when it finds the one you have selected (“FOUND”
and the selected PTY code appear), and tunes in
that station.
Searching for Programs by PTY Codes
(PTY Search)
One of the advantages of RDS is that you can locate a
particular kind of program by specifying the PTY
codes.
• For details on the PTY codes, see “Additional
Information” on page 27.
• If no program is found, “NOTFOUND” appears
on the display and the unit returns to the last
received station.
To search for a program using the PTY codes
REMEMBER you must preset FM RDS stations to use
the PTY codes. If not yet done, see pages 12 and 13.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 1.
To stop searching any time during the process, press
PTY SEARCH while searching.
If you preset a station while PTY Search is
being carried out
PTY Search may not stop. If this happens, press PTY
SEARCH to stop searching manually.
14
Switching Temporarily to a Program
Type of Your Choice
How the Enhanced Other Networks function
actually works:
The Enhanced Other Networks function allows the unit
to switch temporarily to a broadcast program of your
choice (TA, NEWS, and INFO) from a different
station.
• The function only works when you are listening to a
preset FM RDS stations providing the data.
CASE 1
If there is no station broadcasting the program
you have selected
The unit continues tuning in to the current station.
«
When a station starts broadcasting the program
you have selected, the unit automatically switches
to the station. The indicator of received PTY code
starts flashing.
To activate the Enhanced Other Networks function
REMEMBER you must preset FM RDS stations to use
the function. If not yet done, see pages 12 and 13.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 1.
«
When the program is over, the unit goes back to
the previously tuned station, but the function still
remains activated.
On the remote control ONLY:
CASE 2
TA/NEWS
1 Press TA/NEWS/INFO until
/INFO
the data type you want
If there is a station broadcasting the program
you have selected
The unit tunes in to the program. The indicator of
received PTY code starts flashing.
«
When the program is over, the unit goes back to
the previously tuned station, but the function still
remains activated.
appears on the display.
The selected data type indicator (TA,
NEWS, and INFO) also flashes.
• Each time you press the button, the data type
indicators change as follows:
TA
NEWS
INFO
OFF
(Canceled)
CASE 3
TA
: Traffic announcement
If the FM station you are listening to is
broadcasting the program you have selected
The unit continues to receive the station but the
indicator of received PTY code starts flashing.
«
When the program is over, the indicator of
received PTY code stops flashing and remains lit,
but the function still remains activated.
NEWS : News
INFO : Program the purpose of which is to
impart advice in the widest sense.
OFF
: The function is canceled. The data
type indicator (TA, NEWS, and
INFO) goes off.
2 Wait for about 3 seconds after
specifying the data type.
The data type indicator stops flashing and remains
lit.
More about the Enhanced Other Networks
function
The data sent from some stations may not be compatible
with this unit and also some stations may not include
Enhanced Other Networks data. In this case, the function
may not work correctly.
Now, the function is activated. See “How the
Enhanced Other Networks function actually
works.”
•
•
•
•
While listening to a program tuned into by the function, the
station does not change even if another network station
starts broadcasting a program of the same data.
The function is canceled when you change the source to
CD, TAPE or AUX, while it is temporarily canceled when
you change the source to AM (MW).
This function is also canceled when you turn off the unit.
15
Playing Back Discs
Continued
This unit has been designed to play back the following
discs—CD, CD-R, and CD-RW.
3 Close the disc cover gently.
CD
4 Press 3/8 CD.
When playing a CD-R or CD-RW
The unit automatically turns on and the
first track of the disc starts playing.
User-edited CD-Rs (CD-Recordable) and CD-RWs
(CD-ReWritable) can be played only if they are
already “finalized.”
Track number
REC
Elapsed playing time
• Usually you can play back your original CD-Rs or
CD-RWs recorded in music CD format. However,
sometimes they may not play depending on their
characteristics or recording conditions.
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
OVER
• Before playing CD-Rs or CD-RWs, read their
instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not play on this unit
because of their disc characteristics, damage or stain
on them, or if the player’s lens is dirty.
• CD-RWs may require a longer readout time. This is
because the reflectance of CD-RWs is lower than for
regular discs.
• The track number that has already played
disappears from the track calender on the
display.
• The disc automatically stops when the last track
has finished playing.
To stop playing, press 7.
Total track number
Total playing time
General notes
REC
In general, you will have the best performance by
keeping your discs and the mechanism clean.
• Store discs in their cases, and keep them in cabinets
or on shelves.
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
OVER
• Keep the unit’s disc cover closed when
not in use.
To remove the disc, press 0 OPEN on the unit.
Continued use of irregular shape discs
(heart-shape, octagonal, etc.) can damage
the unit.
•
If the disc cannot be read correctly (because it is
scratched, for example) or an unreadable CD-R or CD-
RW is inserted
Playing Back the Entire Disc—Normal Play
Playback will not start.
•
•
If no disc is inserted
“NO DISC” appears on the display.
If the loaded disc has more than 15 tracks
The OVER indicator lights on the display.
1 Press 0 OPEN on the unit.
OPEN
The disc cover opens.
• You can insert a disc while
listening to another source.
DO NOT try to open the disc cover by hand
as it will be damaged.
2 Place a disc correctly with its label side
up.
CORRECT
INCORRECT
16
Basic Disc Operations
Programming the Playing Order of the
Tracks—Program Play
While playing a disc, you can do the following
operations.
You can arrange the order in which tracks play before
you start playing. You can program up to 20 tracks.
To stop playing for a moment
During play, press 3/8 CD.
While pausing, the elapsed playing time
flashes on the display.
CD
On the remote control ONLY:
1 Load a disc.
• If the current playing source is not the CD
player, press 3/8 CD, then 7 before going to
the next step.
To resume playing, press 3/8 CD again.
To go to another track
Before or during play, press ¢ or
4 repeatedly.
• ¢ : Skips to the beginning of the
next or succeeding tracks.
PRGM
2 Press PRGM (program).
The PROGRAM indicator lights up
on the display.
• 4 : Goes back to the beginning of
the current or previous tracks.
PROGRAM
To go to another track directly using the number
buttons
• If a program has been stored in memory, the
program is called up.
On the remote control ONLY:
UP
3 Press
UP or
DOWN
1
4
3
2
5
8
Pressing the number button(s)
before or during play allows you
to start playing the track number
you want.
to select the track number,
then press SET.
6
DOWN
SET
• You can select the track number
directly using the number
button(s). (See “To go to another
track directly using the number
buttons.”)
7
9
Ex.: For track number 5, press 5.
For track number 15, press
+10, then 5.
10
10
For track number 20, press
+10, then 10.
For track number 32, press
+10, +10, +10, then 2.
Track number
Program step number
To locate a particular point in a track
During play, press and hold ¢ or
4.
4 Repeat step 3 to program
CD
other tracks you want.
• ¢ : Fast-forwards the tracks.
• 4 : Fast-reverses the tracks.
5 Press 3/8 CD.
The tracks are played in the order you have
programed.
If you try to program a 21st track
“FULL” will appear on the display.
To stop playing, press 7.
PRGM
To exit from Program Play, press
PRGM (program) before or after playing.
• The PROGRAM indicator goes off.
17
To skip the current track, press ¢.
• You cannot go back to the previous
track by pressing 4.
To check the program contents
You can check the program
contents by pressing ¢ or 4
before or after playback.
• ¢ : To check the contents in
the programmed order.
To stop playing, press 7.
To exit from Random Play, press
RANDOM before or after playing.
Random Play is canceled and Normal Play
resumes.
• 4 : To check the contents in the reverse order.
RANDOM
To modify the program
On the remote control ONLY:
• The RANDOM indicator goes off.
CANCEL
Before or after playing, you can erase the
last programed track by pressing CANCEL.
• Each time you press the button, the last
programed track is erased from the
program.
Repeating Tracks—Repeat Play
You can have all the tracks, the program or individual
track currently playing, repeat as many times as you
like.
To add tracks in the program before playing, simply
select the track numbers you want to add by following
step 3 of the programming procedure.
On the remote control ONLY:
To repeat playing, press REPEAT before
or during play.
REPEAT
To erase the program, press 7 before or
after playing.
• Each time you press the button, Repeat
Play changes as follows, and the
• Pressing 0 OPEN to open the disc cover
will also erase the programed tracks.
following repeat indicator lights up on the display:
ALL
Playing at Random—Random Play
Canceled
: Repeats one track.
The tracks will play in no particular order when you
use this mode.
ALL : In Normal Play, repeats all the tracks.
In Program Play, repeats all the tracks in
the program.
On the remote control ONLY:
In Random Play, repeats all the tracks in
random order.
1 Load a disc.
• If the current playing source is not the CD
player, press 3/8 CD, then 7 before going to
the next step.
To cancel Repeat Play, press REPEAT repeatedly
until the repeat indicator goes off.
• Repeat Play remains in effect even when you select
another play mode (Normal, Program or Random
Play).
RANDOM
2 Press RANDOM.
The RANDOM indicator lights up on
the display.
• In Random Play,
cannot be selected. If
has
been selected when you press RANDOM, it is
canceled.
CD
3 Press 3/8 CD.
The tracks are randomly played.
Random Play ends when all the tracks
are played once.
18
Playing Back Tapes
You can play back type I tapes.
If no cassette is inserted when you press
2 3 TAPE
“NO TAPE” appears on the display.
Playing Back a Tape
To stop playing, press 7.
1 Press ) for cassette deck on the unit.
The cassette holder opens.
To fast-wind to the left or to the
right, press ¢ or 4 while the
tape is not running.
The tape direction indicator (3 or 2)
starts flashing rapidly on the display.
To remove the cassette, press ) on
the unit.
2 Put a cassette in with the exposed part
To play both sides—Reverse Mode
You can set the deck to play just one side of a tape,
both sides once, or both sides continuously.
of the tape down.
On the remote control ONLY:
REV.MODE
Press REV.MODE (reverse mode).
• Each time you press the button, the
Reverse Mode changes as follows:
3 Close the cassette holder cover gently.
: The deck automatically stops after playing
both sides of the tape. Stops when playback
in the 2 direction is finished.
: The deck continues to play both sides of the
tape until 7 is pressed.
: The deck automatically stops after playing
one side of the tape.
The use of C-120 or thinner tape is not
recommended, since characteristic
deterioration may occur and this tape easily
jams in the pinch-rollers and the capstans.
TAPE
4 Press 2 3 TAPE.
The unit automatically turns on and
the tape starts playing. The tape
direction indicator (3 or 2) flashes
slowly on the display.
• Each time you press the button, the tape
direction changes:
3 : plays the front side.
2 : plays the reverse side.
When the tape plays to the end, the deck
automatically stops if the Reverse Mode is set to
or
. (See “To play both sides—Reverse
Mode.”)
19
Recording
Continued
IMPORTANT:
2 Close the cassette holder gently and
check the recording direction for the
tape.
• It should be noted that it may be unlawful to re-
record pre-recorded tapes, records, or discs
without the consent of the owner of copyright in
the sound or video recording, broadcast or cable
program and in any literary, dramatic, musical,
or artistic embodied therein.
• If the tape direction is not correct, press 2 3
TAPE twice then 7 to change the tape direction.
• If you want to record on both sides of a tape, see
“To record on both sides—Reverse Mode.”
• The recording level is automatically set correctly, so
it is not affected by the other sound settings. Thus,
during recording you can adjust the sound you are
actually listening to without affecting the recording
level.
• If recordings you have made have excessive noise or
static, the unit may be too close to a TV. Increase the
distance between the TV and the unit.
3 Start playing the source—FM, AM
(MW) or auxiliary equipment
connected to AUX jacks.
• When the source is the CD player, see “Disc
Direct Recording” on page 21.
ONE TOUCH
4 Press ONE TOUCH
• You can use type I tape for recording.
REC
REC (recording).
REC
The
(recording) indicator
To protect your recording
Cassettes have two
lights up on the display and recording starts.
small tabs on the
back to protect from
unexpected erasure
or re-recording.
•
•
If no cassette is inserted when you press REC
“NO REC” appears on the display.
If a protected tape is inserted when you press REC
“NO REC” appears on the display.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
To stop while recording, press 7.
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus,
when recording discs or radio broadcasts, wind the leader tape
first to ensure that the recording will be made without any
loss.
To remove the cassette, press ) on the
unit.
To record on both sides—Reverse Mode
On the remote control ONLY:
Recording on a Tape
REV.MODE
Press REV.MODE (reverse mode)
On the unit ONLY:
repeatedly until
• When using the Reverse Mode for
recording, lights up and start
recording in the forward (3) direction first.
or
is lit.
1 Put a recordable cassette in with the
exposed part of the tape down.
Otherwise, recording will stop when recording is
done only on one side (reverse) of the tape.
20
To record on both sides—Reverse Mode
On the remote control ONLY:
Disc Direct Recording
Everything on the disc goes onto the tape in the order it
is on the disc, or according to the order you have set in
Program Play.
REV.MODE
Press REV.MODE (reverse mode)
repeatedly until
• When using the Reverse Mode for Disc
Direct Recording, lights up and start
or
is lit.
On the unit ONLY:
recording in the forward (3) direction first. When
the tape reaches its end while recording a song in the
forward direction (3), the last song will be re-
recorded at the beginning of the reverse side (2).
If you start recording on the reverse side (2),
recording will stop when recording is done only on
one side (reverse) of the tape.
1 Put a recordable cassette in with the
exposed part of the tape down.
2 Load a disc.
• If the current playing source is not the CD
player, press 3/8 CD, then 7 before going to
the next step.
When making Sleep Timer settings while doing
Disc Direct Recording
Set enough time to allow for the disc to finish playing;
otherwise, the power will go off before recording is
completed.
— If you do not want pauses of about 4 seconds
recorded between selections, press 3/8 CD
twice. Otherwise, a non-recorded pause will
be automatically inserted between selections.
• If you want to record on both sides of a tape, see
“To record on both sides—Reverse Mode.”
One Track Recording
ONE TOUCH
3 Press ONE TOUCH
REC
REC (recording).
This recording method is convenient when you record
tracks while playing the disc. You can record just your
favorite songs on the tape.
REC
The
(recording) indicator
lights up on the display and recording starts.
After recording, the CD player and cassette deck
automatically stop.
On the unit ONLY:
1 Put a recordable cassette in with the
To stop while recording, press 7.
The tape stops after 4 seconds.
exposed part of the tape down.
2 Play the track on the disc you wish to
To remove the cassette, press ) on the
unit.
record.
ONE TOUCH
3 Press ONE TOUCH
REC
REC (recording).
The CD player returns to the
beginning of that track and the track is recorded on
the tape.
After recording, the CD player and cassette deck
automatically stop.
4 Repeat steps 2 and 3 to record other
tracks you want.
To stop while recording, press 7.
The tape stops after 4 seconds.
To remove the cassette, press ) on the
unit.
21
Using the Timers
Continued
There are four timers available—Daily Timer,
Recording Timer, Snooze Timer, and Sleep Timer.
Before using the timers, you need to set the unit’s
clock (see page 10).
2 Set the on-time when you want the unit
UP
to turn on.
On the remote control:
DOWN
1) Press
UP or
DOWN to set
the hour, then press
CLOCK/TIMER.
CLOCK
/ TIMER
Using Daily Timer and Recording Timer
2) Press
UP or
DOWN to set
the minute, then press
CLOCK/TIMER.
You can set the timer whether the unit is on or off.
On the unit:
How the timer actually works
1) Press ¢ or 4 to set the
hour, then press TIMER/
SNOOZE.
2) Press ¢ or 4 to set the
minute, then press
When the on-time comes, the unit automatically turns
on (the
[timer] indicator flashes just before the on-
time and continues flashing while the timer is
operating). Then, when the off-time comes, the unit
automatically turns off (standby).
The timer setting remains in memory until you change
it.
TIMER/SNOOZE
TIMER/SNOOZE.
The OFF indicator lights up and the unit enters
off-time setting mode.
• When the
(timer) indicator is lit on the display,
the timer acts as the Daily Timer. Once the timer has
been set, it will be activated at the same time
everyday until the timer is turned off.
OFF
• When the
(timer) and the REC indicators are lit
on the display, the timer acts as the Recording Timer.
After the timer-recording finishes, the details of the
setting remain stored but the timer is turned off.
3 Set the off-time when you want the unit
to turn off (standby).
On the remote control:
Before you start...
1) Press
UP or
DOWN to set the hour, then
When using “TUNER” as the source to play, make
sure to select the desired station before turning off the
power.
press CLOCK/TIMER.
2) Press
UP or
DOWN to set the minute,
then press CLOCK/TIMER.
• There is a time limit in doing the following steps. If
the setting is canceled before you finish, start over
from step 1.
On the unit:
1) Press ¢ or 4 to set the hour, then press
TIMER/SNOOZE.
2) Press ¢ or 4 to set the minute, then press
TIMER/SNOOZE.
CLOCK
1 Press CLOCK/TIMER
(or TIMER/SNOOZE on
the unit).
/ TIMER
The unit enters the timer selecting mode.
The
(timer) and the ON
TIMER/SNOOZE
indicators light up and the
current on-time flashes on the
display.
The unit enters on-time setting mode.
ON
22
UP
4 Select the timer (Daily
Timer or Recording Timer)
with the source to play.
On the remote control:
6 Adjust the clock if you need.
• See “Setting the Clock” on page 10.
DOWN
STANDBY/ON
7 Press STANDBY/ON
(or
on the unit) to turn
Press
UP or
DOWN to
CLOCK
/ TIMER
select the timer, then press
CLOCK/TIMER.
off the unit (standby) if you
have set the timer with the
unit turned on.
On the unit:
Press ¢ or 4 to select the
timer, then press TIMER/SNOOZE.
• When the timer turns on the unit, the
(timer)
indicator starts flashing. (If the Recording Timer
is selected in step 4, the REC indicator also
starts flashing.)
• Each time you press
UP
(¢) or DOWN (4), the
TIMER/SNOOZE
timer mode and the source
change as follows:
CLOCK
To deactivate the timer temporarily,
/ TIMER
press and hold CLOCK/TIMER (or
TIMER/SNOOZE on the unit) until
REC
TUNER
TAPE
TUNER
the
(timer) indicator on the display
CD
goes off.
TIMER/SNOOZE
TUNER : tunes in to the last station you were
To activate or change the timer
(with the previous setting), follow
steps 1 to 7 on pages 22 and 23.
• If you want to change the timer setting after the
Daily Timer be used, first deactivate the timer.
listening to. (Daily Timer)
REC TUNER : records the last station you were
listening to. (Recording Timer)
• Put a recordable cassette into the deck.
CD : plays a disc. (Daily Timer)
• Load a disc.
TAPE : plays a tape. (Daily Timer)
• Make sure that the tape is in the cassette
deck.
•
•
If the unit is turned on when the timer on-time comes
Timer does not work.
When you unplug the power cord or if a power failure
occurs
• Make sure that the tape direction is
correct.
The unit enters the volume level setting mode.
The timer will be canceled. You need to set the clock first,
then the timer again.
5 Select the volume level.
On the remote control:
Press
UP or
DOWN to set the volume level,
then press CLOCK/TIMER.
On the unit:
Press ¢ or 4 to set the volume level, then
press TIMER/SNOOZE.
• You can select the volume level
(“VOLUME – –” and “VOLUME 0” to
“VOLUME 40”).
If you select “VOLUME – –,” the volume is set
to the previous level when the unit was turned
off.
• To turn off the volume while the Recording
Timer (REC TUNER) is working, set the volume
level “VOLUME 0.”
The unit enters the clock setting mode.
23
Using Snooze Timer
Using Sleep Timer
The Snooze Timer turns off the unit (standby) only for
5 minutes while the Daily Timer is in operation.
• You can set the Snooze Timer only while the Daily
Timer is in operation.
With the Sleep Timer, you can fall asleep to music. You
can set the Sleep Timer when the unit is turned on.
How the Sleep Timer actually works
The unit automatically turns off after the specified time
length passes.
TIMER/SNOOZE
Press TIMER/SNOOZE on
the unit (or CLOCK/TIMER
on the remote control) while
On the remote control ONLY:
the Daily Timer is in operation.
SLEEP
CLOCK
1 Press SLEEP.
/ TIMER
The unit turns off (standby) and the
The time length until the shut-off time
SNOOZE
indicator lights up on the display.
SLEEP
appears and the
up on the display.
indicator lights
After 5 minutes, the unit automatically
turns on.
• Each time you press the button, the time length
changes as follows:
SLEEP 10 SLEEP 20 SLEEP 30
SLEEP 60
Canceled SLEEP120 SLEEP 90
•
•
•
If the unit is turned on when the Snooze Timer is
working
The Snooze Timer and the Daily Timer will be canceled.
If you set the Snooze Timer when there is less than 5
minutes until the Daily Timer off-time
The unit will not turn on even when 5 minutes passed.
When you unplug the power cord or if a power failure
occurs
2 Wait for about 5 seconds after
specifying the time length.
To check the remaining time until the shut-off time,
press SLEEP once so that the remaining time until the
shut-off time appears for about 5 seconds.
The timer will be canceled. You need to set the clock first,
then the timer again.
To change the shut-off time, press SLEEP repeatedly
until the desired time length appears on the display.
To cancel the setting, press SLEEP repeatedly until
SLEEP
the
indicator goes off.
• The Sleep Timer is also canceled when you turn off
the unit.
•
•
If you set the Sleep Timer after the Daily Timer starts
playing the selected source
The Daily Timer is canceled. When the Sleep Timer shut-
off time comes, the unit will be turned off.
If you set the Sleep Timer after the Recording Timer
starts recording
The Recording Timer is canceled, but recording continues
until the Sleep Timer shuts off the power.
24
Maintenance
To get the best performance from the unit, keep your discs, tapes, and mechanism clean.
Cleaning the unit
Handling cassette tapes
• If the tape is loose in its cassette,
take up the slack by inserting a
pencil in one of the reels and
rotating.
• If the tape is loose, it may get
stretched, cut, or caught in the
cassette.
• Stains on the unit
Should be wiped off with a soft cloth. If the unit is
heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe
clean with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or have its paint peel, be careful about
the following.
• Be careful not to touch the tape
surface.
• Avoid storing tapes in the following
places:
—DO NOT wipe it with a rough cloth.
—DO NOT wipe it strongly.
—In dusty places
—In direct sunlight or heat
—In moist areas
—DO NOT wipe it with thinner or benzine.
—DO NOT apply any volatile substances such as
insecticides to it.
—On a TV or speaker
—Near a magnet
—DO NOT allow any rubber or plastic to remain in
contact with it for a long time.
To keep the best recording and playback sound
quality
If the heads, capstans, and pinch rollers of the cassette
deck become dirty, the following will occur:
• Impaired sound quality
Handling discs
• Remove the disc from its case by
holding it at the edge while
pressing the center hole lightly.
• Do not touch the shiny surface of
the disc, or bend the disc.
• Discontinuous sound
• Put the disc back in its case after
use to prevent warping.
• Fading
• Incomplete erasure
• Difficulty in recording
• Be careful not to scratch the
surface of the disc when
placing it back in its case.
• Avoid exposure to direct
sunlight, temperature extremes,
and moisture.
To clean the heads, capstans, and pinch rollers
Use a cotton swab moistened with alcohol.
Capstans
To clean the disc
Wipe the disc with a soft cloth
in a straight line from center to
edge.
Heads
Pinch Rollers
To demagnetize the heads
Turn off the unit, and use a head demagnetizer
(available at electronics and audio shops).
DO NOT use any solvent—such as conventional
record cleaner, spray, thinner, or benzine—to clean
the disc.
25
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified
person, such as your dealer, for service.
Symptom
Cause
Action
No sound is heard.
• Connections are incorrect or
loose.
• Headphones are connected.
• Check all connections and make
corrections. (See pages 6 – 9.)
• Disconnect the headphones.
Hard to listen to broadcasts because • Antennas are disconnected.
• Reconnect the antennas correctly
of noise.
and securely.
• The AM loop antenna is too close • Change the position and direction
to the unit.
• The FM antenna is not properly
extended and positioned.
of the AM loop antenna.
• Extend the FM antenna to the best
position.
The disc does not play.
The disc is placed upside down.
The disc is scratched or dirty.
Place the disc with the label side up.
The disc sound is discontinuous.
Clean or replace the disc. (See page
25.)
The cassette holder cannot be
opened.
Power from the power cord has been Plug in the power cord, then turn on
cut off while the tape was running.
the unit.
Impossible to record.
Small tabs on the back of the
cassette are removed.
Cover the holes with adhesive tape.
Operations are disabled.
The built-in microprocessor may
malfunction due to external
electrical interference.
Unplug the power cord and then
plug it back in.
Unable to operate the unit from the
remote control.
• The path between the remote
control and the remote sensor on
the unit is blocked.
• Remove the obstruction.
• The batteries are exhausted.
• Replace the batteries.
26
Additional Information
Description of the PTY codes:
NEWS:
News.
NATION M:
OLDIES:
Current popular music of the nation or
region in that country’s language.
AFFAIRS:
Topical program expanding or enlarging
upon the news—debate, or analysis.
Music from the so-called “golden age” of
popular music.
INFO:
Program the purpose of which is to impart
advice in the widest sense.
FOLK M:
Music which has its roots in the musical
culture of a particular nation.
SPORT:
Program concerned with any aspect of
sports.
DOCUMENT: Program concerning factual matters,
presented in an investigative style.
EDUCATE:
DRAMA:
Educational programs.
TEST:
Broadcasts for testing emergency broadcast
equipment or receiver.
All radio plays and serials.
CULTURE:
Programs concerning any aspect of national
or regional culture, including language,
theater, etc.
ALARM:
Emergency announcement.
SCIENCE:
Programs about natural sciences and
technology.
Classification of the PTY codes for some FM
stations may be different from the above list on
this page.
VARIED:
Used for mainly speech-based programs
such as quizzes, panel games and
personality interviews.
POP M:
Commercial music of current popular
appeal.
ROCK M:
Rock music.
Alarm function
EASY M:
Current contemporary music considered to
If an “ALARM” (Emergency) signal is received
from a station while listening to the radio, the unit
automatically switches to the station broadcasting
the “ALARM” signal, except when you are
listening to non-RDS stations—all AM (MW) and
some FM stations.
be “easy-listening.”
LIGHT M:
CLASSICS:
OTHER M:
Instrumental music, and vocal or choral
works.
Performances of major orchestral works,
symphonies, chamber music, etc.
Music not fitting into any of the other
categories.
Test function
The “TEST” signal is used for testing the
“ALARM” signal.
Therefore, it makes the unit work in the same way
as the “ALARM” signal does.
If a “TEST” signal is received from a station while
listening to the radio, the unit automatically
switches to the station broadcasting the “TEST”
signal, except when you are listening to non-RDS
stations—all AM (MW) and some FM stations.
WEATHER:
Weather reports and forecasts.
FINANCE:
Stock Market reports, commerce, trading
etc.
CHILDREN: Programs targeted at a young audience.
SOCIAL:
Programs about sociology, history,
geography, psychology and society.
RELIGION:
Religious programs.
PHONE IN:
Involving members of the public expressing
their views either by phone or at a public
forum.
TRAVEL:
LEISURE:
JAZZ:
Travel information.
Programs about recreational activities.
Jazz music.
COUNTRY:
Songs which originate from, or continue the
musical tradition of the American Southern
States.
27
Specifications
Amplifier
General
Power requirement:
AC IN:
Output Power:
20 W (10 W + 10 W) at 4 Ω (10% THD)
Audio input sensitivity/Impedance (at 1 kHz)
230 V
, 50 Hz
DC IN:
12 V, 4 A
AUX:
Speakers/Impedance:
500 mV/48.75 kΩ
4 Ω
Power consumption:
35 W (at operation)
3.0 W (on standby)
Dimensions (approx.):
412 mm x 208 mm x 275 mm (W/H/D)
Tuner
Mass (approx.):
6.5 kg
FM tuning range: 87.50 MHz – 108.00 MHz
AM tuning range:
MW:
522 kHz – 1 629 kHz
Design and specifications are subject to change
without notice.
CD player
Dynamic range:
85 dB
Signal-to-noise ratio:
Wow and flutter:
90 dB
Immeasurable
Cassette deck
Frequency response:
Normal (type I):
Wow and flutter:
50 Hz – 15 000 Hz
0.15% (WRMS)
Speaker
Speaker units:
Full range:
8.0 cm cone x 1
Impedance:
Dimensions (approx.):
4 Ω
135 mm x 203 mm x 190 mm (W/H/D)
Mass (approx.): 1.7 kg each
Supplied Accessories
See page 6.
28
VICTOR COMPANY OF JAPAN, LIMITED
EN
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
0103MWMMDWJEM
|