USB DRIVER
INSTALLATION GUIDE
Thank you for using the Icom Download Service.
Please read this installation guide before installing the USB driver into your PC that is connected to the IC-7200
with the USB (Universal Serial Bus) cable (third party).
OVERVIEW
When the transceiver is connected to a PC with the
USB cable, the following operations can be performed;
System requirements
The PC which supports the following OS (Operating
System) is required;
• Remote control operation (CI-V: Icom Communica-
tion Interface-V) by the PC.
• Modulation input from the PC.
•
•
•
Microsoft® Windows Vista™
Microsoft® Windows® XP
Microsoft® Windows® 2000
• Received audio output to the PC.
NOTE:
USB cable
(third party)
• The USB driver is not supported for Microsoft®
Windows® XP (64 bit).
• Icom is not responsible for whole performance of
the PC that supports above OS.
• In this installation guide, the above OS are de-
scribed as “Windows Vista,” “Windows XP” and
“Windows 2000.”
Transceiver
PC
NOTE:
•
PC software (third party) may be required. (p. 18)
• The CT-17 ci-v level converter is required for re-
mote control operation (CI-V) when the USB cable
is not used. See p. 88 in the IC-7200 instruction
manual for details.
Item requirements
• USB cable (A-B type/third party)
• The transceiver connection may not be recog-
nized by the PC because of the USB cable length.
Using the shorter USB cable as possible is rec-
ommended.
A type
B type
• PC (with USB 1.1 or 2.0)
• Installed audio player
• PC software (third party)
- See p. 18 for details.
Icom, Icom Inc. and the
logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
Microsoft, Windows and Windows Vista are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other
countries.
All other products or brands are registered trademarks or trademarks of their
respective holders.
1
PREPARING
Before installing the USB driver
Icom HP gives the USB driver download service.
Before installing the USB driver, download the follow-
ing compressed file.
• USB driver
(File name: 7200UsbDrv_v100.zip)
Icom is not responsible for any damage or lack of
data resulting from the use of the USB driver.
3
DRIVER INSTALLATION
Windows Vista
NOTE:
• NEVER connect the transceiver to the PC with the USB cable (third party) until the USB driver installation
has been completed.
• The USB driver for Windows Vista does not support the automatic recognition system.
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
t“A program needs your permission to continue” dia-
logue box appears as below.
Click [Continue].
q
Make sure that the transceiver is not connected to
the PC.
Click
w Start up Windows.
• Quit all other application if running.
e Double-click the “WinVista” folder.
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞ “WinVista”
yVerify the installation location, then click [Install].
Click
Double click
uWindows starts scanning for the system, then starts
installing the USB driver.
r Double-click the “CP210xVCPInstaller.exe” to start
up the USB driver installer.
iAfter the installation is completed, click [OK].
• Restarting the PC is recommended.
Click
Double click
☞ Continues to the next page
4
DRIVER INSTALLATION
Windows Vista (Continued)
oAfter restarting the PC, connect the transceiver to
the PC with the USB cable (third party) as shown
below.
!Turn the transceiver power ON.
• “Installing device driver software” appears as below.
• Be sure to connect the USB cable correctly and not up-
side down.
REMOTE
!After the dialogue appears as below, USB driver
installation has been completed.
KEY
SEND
ALC
ACC
Transceiver
To USB jack
Type B
USB cable
(third party)
Type A
PC
To USB port
5
DRIVER INSTALLATION (Continued)
Windows XP
NOTE:
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB
driver.
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
tThe “Welcome to the Found New Hardware Wizard”
will come up as below.
Select “No, not this time,” then click [Next>].
q
Make sure that the transceiver is not connected to
the PC.
w Start up Windows.
• Quit all other application if running.
eConnect the transceiver to the PC with the USB
cable (third party) as shown below.
• Be sure to connect the USB cable correctly and not up-
side down.
Select
Click
REMOTE
ySelect “Install from a list or specific location
(Advanced),” then click [Next>].
KEY
SEND
ALC
ACC
Transceiver
To USB jack
Type B
Select
USB cable
(third party)
Click
uSelect “Search for the best driver in these locations.”
then select “Include this location in the search,” and
click [Browse].
Type A
PC
Select
To USB port
Click
Select
rTurn the transceiver power ON.
• “Found New Hardware” appears as below.
☞ Continues to the next page
6
DRIVER INSTALLATION
Windows XP (Continued)
i Select the “Win” folder, then click [OK].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞ “Win”
!Windows starts installing the USB driver.
Select
Click
oClick [Next>].
!After the installation is completed, click [Finish].
Click
Click
!The Wizard starts searching for the driver and
!
After clicking [Finish], the dialogue appears as below.
shows the dialogue below during search.
!The “Welcom to the Found New Hardware Wizard”
will come up again to install the USB serial port
driver.
Select “No, not this time,” then click [Next>].
!After the driver is found, the “Hardware Installation”
dialogue box appears as below.
Click [Continue Anyway] to start the installation.
Select
Click
Click
☞ Continues to the next page
7
DRIVER INSTALLATION
Windows XP (Continued)
!Select “Install from a list or specific location
@The Wizard starts searching for the driver and
(Advanced),” then click [Next>].
shows the dialogue below during search.
Select
Click
@After the driver is found, the “Hardware Installation”
dialogue box appears as below.
!Select “Search for the best driver in these locations.”
then select “Include this location in the search:”,
and click [Browse].
Click [Continue Anyway] to start the installation.
Select
Click
Select
Click
@Windows starts installing the USB driver.
! Select the “Win” folder, then click [OK].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞ “Win”
Select
Click
@After the installation is completed, click [Finish].
!Click [Next>].
Click
Click
@
After clicking [Finish], the dialogue appears as below.
• Restarting the PC is recommended.
8
DRIVER INSTALLATION (Continued)
Windows 2000
NOTE:
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB
driver.
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
tThe “Found New Hardware Wizard” will come up as
below.
Click [Next>].
q
Make sure that the transceiver is not connected to
the PC.
w Start up Windows.
• Quit all other application if running.
eConnect the transceiver to the PC with the USB
cable (third party) as shown below.
• Be sure to connect the USB cable correctly and not up-
side down.
Click
REMOTE
ySelect “Search for a suitable driver for my device
(recommended),” then click [Next>].
KEY
SEND
ALC
ACC
Transceiver
To USB jack
Type B
Select
USB cable
(third party)
Click
uSelect “Specify a location,” then click [Next>].
Type A
PC
To USB port
Select
Click
rTurn the the transceiver power ON.
• “Found New Hardware” appears as below.
iClick [Browse...].
Click
☞ Continues to the next page
9
DRIVER INSTALLATION
Windows 2000 (Continued)
oSelect “slabbus.inf” in the “Win” folder, then click
!After the installation is completed, click [Finish].
[Open].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞ “Win”
Select
“slabbus.inf”
Click
Click
!The “Found New Hardware Wizard” appears again.
Click [Next>].
!Click [OK].
Click
Click
!When the driver is found, the following dialogue is
displayed.
Click [Next>] to start the installation.
!Select “Search for a suitable driver for my device
(recommended),” then click [Next>].
Click
Select
Click
!Select “Specify a location,” then click [Next>].
Select
Click
☞ Continues to the next page
10
DRIVER INSTALLATION
Windows 2000 (Continued)
!Click [Browse...].
!When the driver is found, the following dialogue is
displayed.
Click [Next>] to start the installation.
Click
!Select “slabw2k.inf” in the “Win” folder, then click
[Open].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞ “Win”
Click
@After the installation is completed, click [Finish].
Select
“slabw2k.inf”
• Restarting the PC is recommended.
Click
!Click [OK].
Click
Click
11
COM PORT CONFIRMATION
After the driver installation is completed, confirming the driver availability and the port number is recommended.
Windows Vista
Windows XP
q Start up Windows.
For Windows 2000:
w Right click “Computer,” then select “Properties.”
• “Computer” is available in <Start> menu.
e “System” screen appears as below.
Click [Device Manager].
Refer to the following instructions because the
operations of Windows 2000 are similar to Windows
XP.
q Start up Windows.
w Right click “My Computer,” then select “Properties.”
• “My Computer” is available in <Start> menu.
e “System Properties” screen appears as below.
Click [Hardware] tab and then click [Device Man-
ager].
Click
Click
Click
r In case “User Account Control” dialogue box ap-
pears as below, click [Continue].
r “Device Manager” screen appears.
Click “ ” of “Ports (COM&LPT).”
t Confirm “CP210x USB to UART Bridge Controller
(COMM)” is displayed.
• If “!” or “×” indicator is displayed on the “Device Man-
ager” screen, the driver may not be installed properly.
Un-install the USB driver then reinstall in such cases.
Click
“M” is the COM port number, that is used for the
communication setting with the utility software.
t “Device Manager” screen appears.
Click “ ” of “Ports (COM&LPT).”
y Confirm “CP210x USB to UART Bridge Controller
(COMM)” is displayed.
q Click “
”
• If “!” or “×” indicator is displayed on the “Device Man-
ager” screen, the driver may not be installed properly.
Un-install the USB driver then reinstall in such cases.
“M” is the COM port number, that is used for the
communication setting with the utility software.
q Click “
”
Check the COM port number.
(In this example, the USB serial
COM port number is “8.”)
w
Check the COM port number.
(In this example, the USB serial
COM port number is “8.”)
w
12
DRIVER UNINSTALLATION
The displayed dialogue boxes or indications may differ slightly from the following instructions according to your
system conditions, or environment.
Windows Vista
Windows XP
q Start up Windows.
For Windows 2000:
w Select the “Control Panel” in the Start menu.
• The control panel appears as shown in the next step
below.
e Click the “Uninstall a program.”
• The “Uninstall or Change a Program” menu appears.
Refer to the following instructions because the
operations of Windows 2000 are similar to Windows
XP.
q Start up Windows.
w Select the “Control Panel” in the Start menu.
• The control panel appears as shown in the next step
below.
e Click the “Add or Remove Programs.”
• The “Add or Remove Programs” menu appears.
Click
Click
r Double-click “Silicon Laboratories CP210x USB to
UART Bridge (DriverRemoval).”
r Select “CP210x USB to UART Bridge Controller,”
t In case “User Account Control” dialogue box ap-
then click [Change/Remove].
pears as below, click [Continue].
Click
Click
y The “Confirm Uninstall” appears.
Click [Uninstall] to uninstall the program from the
PC.
t The “Ready to uninstall CP210x USB to UART
Bridge Controller Driver?” appears.
Click [Yes] to uninstall the program from the PC.
• The uninstallation starts.
• The uninstallation starts.
Click
Click
y After the uninstall is completed, click [OK.]
u After the uninstall is completed, click [OK].
• Restarting the PC is recommended.
• Restarting the PC is recommended.
Click
Click
13
FORYOUR REFERENCE
When the transceiver is connected to a PC with the USB cable (third party), remote control operation can be per-
formed with the CI-V command.
The IC-7200 has the USB-Serial convert function, so the PC recognizes the connected transceiver as COM port
and the CI-V control software can be used.
Simultaneous use of the [USB] and [REMOTE] jacks are available.
COM Port setting
To change the COM Port number setting, connect the transceiver to the PC and then turn the transceiver power ON
after the driver installation is completed.
Windows Vista
q Start up Windows.
y Click [Port Settings] tab, then click [Advanced...].
w Right click “Computer,” then select “Properties.”
• “Computer” is available in <Start> menu.
e “System” screen appears as below.
Click [Device Manager].
Click
Click
Click
r In case “User Account Control” dialogue box ap-
pears as below, click [Continue].
u Set the desired COM port number, then click [OK].
Click
Click
Set
t “Device Manager” screen appears.
Right click “CP210x USB to UART Bridge Controller
(COMM)” and then click “Properties.”
i Click [OK] to close the screen.
“M” is the COM port number, that is used for the
communication setting with the utility software.
Right-click
Click
Click
14
FOR YOUR REFERENCE
COM Port setting (Continued)
Windows XP
t Click [Port Settings] tab, then click [Advanced...].
For Windows 2000:
Refer to the following instructions because the
operations of Windows 2000 are similar to Windows
XP.
Click
q Start up Windows.
w Right click “My Computer,” then select “Properties.”
• “My Computer” is available in <Start> menu.
e “System Properties” screen appears as below.
Click [Hardware] tab and then click [Device Man-
ager].
Click
Click
Click
y Set the COM port number if desired, then click
[OK].
r “Device Manager” screen appears.
Right click “CP210x USB to UART Bridge Controller
(COMM)” and then click “Properties.”
Click
“M” is the COM port number, that is used for the
communication setting with the utility software.
Set
u Click [OK] to close the screen.
Right-click
Click
Click
15
FOR YOUR REFERENCE (Continued)
About audio
When the transceiver is connected to a PC with the USB cable (third party), the following operations can be
performed;
• Received audio output to the PC.
• Modulation input from the PC.
The set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’ must be set as “U” (USB) for
modulation input from the PC.
See p. 17 on this installation guide or p. 77 on the IC-7200 instruction manual for details of settings.
[Received audio output to the PC]
The received audio output format
The received audio output format from the USB jack is listed as below.
The number of data bit 16-bit
The received audio output Sampling rate*
8/11.025/16/22.05/32/44.1/48 kHz
The number of channel Monaural (Stereo: The same audio signals are output from both L/R.)
* The sampling rate other than those above can be used according to the application.
The received audio output
The same audio signals are output from the USB jack and the ACC socket.
• The received audio is always output regardless of the squelch condition (open/close).
(The beep tones and the voice synthesizer announcements are not output).
• The received audio output level cannot be adjusted with the [AF] control.
Operating mode
The modulation input can be used when SSB (LSB/USB), SSB data (LSBD/USBD), AM and AM data (AMD)
mode is in use.
16
FOR YOUR REFERENCE
About audio (Continued)
The modulation input settings
To input the audio signal from the USB jack of the transceiver, set the modulation input connector as “USB” in the
set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’, or CI-V system (command).
• When the data mode is OFF (SSB or AM mode is in use)
<Set mode>
M-CH/RIT
SET
q Push and hold
for 1 sec. twice to enter
the set mode.
w Rotate [M-CH] to select “Mod.”
e Rotate [DIAL] to select the modulation input
connector as “U” (USB) when the data mode is
OFF.
ANF
METER
NB NR
1
1.8
2
3.5
3
7
V/M
A/B
=
SPLIT
4
10
5
14
6
18
MW
M-CL
AGC
VOX
COMP 7
21
8
24
9
28
SCAN
.
0
50
F-INP ENT
BAND
MODE
TS
RIT GENE MNF
P
.AMP
TUNER FILTER
SPCH
ATT
M-CH/RIT
SET
[DIAL]
[M-CH]
U (USB)
M-CH/RIT
SET
r Push
to exit the set mode and return to
normal operation.
<CI-V system>
Send the command “FE FE 76 E0 1A 03 23 03 FD”* to the transceiver.
USB
*The transceiver’s address is described as “76” and the controller’s address is described as “E0” for examples
in this guide.
• When the data mode is ON (SSB data or AM data mode is in use)
<Set mode>
M-CH/RIT
SET
q Push and hold
for 1 sec. twice to enter
the set mode.
w Rotate [M-CH] to select “D-Mod.”
e Rotate [DIAL] to select the modulation input con-
nector as “U” (USB) when the data mode is ON.
ANF
METER
NB NR
1
1.8
2
3.5
3
7
V/M
A/B
=
SPLIT
4
10
5
14
6
18
MW
M-CL
AGC
VOX
COMP 7
21
8
24
9
28
SCAN
.
0
50
F-INP ENT
BAND
MODE
TS
RIT GENE MNF
P
.AMP
TUNER FILTER
SPCH
ATT
M-CH/RIT
SET
[DIAL]
[M-CH]
U (USB)
M-CH/RIT
SET
r Push
to exit the set mode and return to
normal operation.
<CI-V system>
Send the command “FE FE 76 E0 1A 03 24 03 FD”* to the transceiver.
USB
*The transceiver’s address is described as “76” and the controller’s address is described as “E0” for examples
in this guide.
17
FOR YOUR REFERENCE
About audio (Continued)
USB level setting
Set the input modulation level of the USB jack in the set mode item ‘USB Level’ or CI-V system (command).
<Set mode>
M-CH/RIT
SET
q Push and hold
for 1 sec. twice to enter
the set mode.
w Rotate [M-CH] to select “USB LVL.”
e Rotate [DIAL] to set the input modulation level of
the USB jack within 0% to 100% in 1% steps.
ANF
METER
NB NR
1
1.8
2
3.5
3
7
V/M
A/B
=
SPLIT
4
10
5
14
6
18
MW
M-CL
AGC
VOX
COMP 7
21
8
24
9
28
SCAN
.
0
50
F-INP ENT
BAND
MODE
TS
RIT GENE MNF
P
.AMP
TUNER FILTER
SPCH
ATT
M-CH/RIT
SET
[DIAL]
[M-CH]
50% (default)
M-CH/RIT
SET
r Push
to exit the set mode and return to
normal operation.
<CI-V system>
Send the command “FE FE 76 E0 1A 03 25 0128 FD”* to the transceiver from the PC.
Input modulation level
• 0000 (0%) to 0255 (100%) can be set as the input modulation level.
*The transceiver’s address is described as “76,” the controller’s address is described as “E0” and input modula-
tion level is described as “0128 (50%)” for examples in this guide.
The modulation input audio format
The modulation input audio format from the USB jack is listed as below.
The number of data bit
Sampling rate*
16-bit
Modulation input
32/44.1/48 kHz
The number of channel Monaural (Stereo: The audio signal from L is input.)
* The sampling rate other than those above can be used according to the application.
[Installed audio player] (Windows standard software, etc.)
®
When using the audio software (e.g.Windows standard software; Microsoft Sound Recorder, etc.), the following
operations can be performed;
• Received audio output to the PC.
• Modulation input from the PC.
PC software (third party) is additionally required when the following operations are performed;
• Monitoring the received audio with the speaker that is connected to the PC.
• Modulation input for the PC microphone’s audio.
18
FOR YOUR REFERENCE (Continued)
Specifications
Connector type
Interface
USB B type
USB 2.0/1.1
Power supply
Support OS
Self power
The PC cannot recognize the transceiver when the power is OFF.
Windows Vista
Windows XP
Windows 2000
Compliant for CI-V spec.
Asynchronous serial
Construction (1 bite)
Start bit
Serial for CI-V
: 1
Data bit
: 8
Parity bit
: No
Stop bit
: 1
Speed
: 300/1200/4800/9600/19200 bps
Received audio output
Modulation input
Number of data bit
Sampling rate
Number of channel
Number of data bit
Sampling rate
Number of channel
: 16-bit
: 8/11.025/16/22.05/32/44.1/48 kHz
: Monaural (Stereo: The same audio signals are output from both L/R.)
: 16-bit
: 32/44.1/48 kHz
: Monaural (Stereo: The audio signal from L is input.)
All stated specifications are subject to change without notice or obligation.
A-6668-3EX © 2008 Icom Inc.
19
|