1.5V x 3
“AAA” (LR03)
Battery
Information
SHOWN ACTUAL SIZE
We recommend the use of alkaline
batteries for longer battery life.
Battery Installation
BATTERY COMPARTMENT DOOR
• Locate the battery compartment on the
clock tower.
• Loosen the screw in the battery compartment
door with a Phillips screwdriver. Remove the
battery compartment door.
• Insert three “AAA” (LR03) alkaline batteries.
• Replace the battery compartment door and
tighten the screw with a Phillips screwdriver.
Do not over-tighten.
• When sounds from this toy become faint
or stop, it’s time for an adult to change
the batteries.
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid
battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Never short-circuit the battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable
batteries.
• Insert batteries as indicated inside the
battery compartment.
• Remove rechargeable batteries from the
toy before charging.
• Remove batteries during long periods of
non-use. Always remove exhausted
batteries from the toy. Dispose of
batteries safely. Do not dispose of
batteries in a fire. The batteries may
explode or leak.
• If removable, rechargeable batteries are
used, they are only to be charged under
adult supervision.
3
For layout ideas visit the
GeoTrax™ section of
Care
Wipe the toy with a clean cloth dampened with a
mild soap and water solution. Do not immerse the toy.
Questions? We'd like to hear from you!
Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS (5437)s,
8 AM - 6 PM EST Monday through Friday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470.
Or, write to: Fisher-Price® Consumer Relations, 636 Girard Avenue
East Aurora, New York 14052, U.S.A.
For other countries outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R
3W2. Great Britain: telephone 01628 500302. Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag
#870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. New Zealand: 16-18 William
Pickering Drive, Albany 1331, Auckland. Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre,
Harbour City, Tsimshatsui, HK, China.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2004 Mattel, Inc. All Right Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
C5218a-0920
Assembly
CHIMNEY
4
1
CROSS TRACK
BASE
“Snap” the cross track into the base.
“Snap” the chimney into the top of
the tower.
2
PLAIN
OVERHANG
5
“Snap” the plain overhangs into the
base, as shown.
ARCHED
OVERHANG
3
Place the tower onto the
base assembly.
“Snap” the arched overhangs into
the tower, as shown.
Assembly is now complete!
5
Chimes & Music!
When a train travels through the middle or top level of the tower, you’ll hear
chimes and music.
PRESS
1
POWER
SWITCH
2
• Locate the power switch near the
top of the tower.
• Slide the switch to the
to turn the toy on and the
position to turn the toy off.
position
•
• Press the chimney to
activate the tower.
°
• When the train goes
through either the
middle level or top
level of the tower,
you’ll hear chimes
and music.
Hint: If the a train does not pass through the clock tower in a few minutes, the tower turns off
automatically and plays a chime. Press the chimney again to turn the tower back on.
Important: The clock tower sound effect feature is activated by contrast in lighting. This feature
may not work if the toy is in very bright light or direct sunlight. Please keep the clock tower out of
bright light or direct sunlight.
6
Three Levels of
Track Layouts!
TRACK NOT INCLUDED
• To build a layout on the bottom level, just
place a straight track (not included)
through the bottom arch of the tower.
LEVEL
1
• Use an Elevation Track Pack
(sold separately) to access
the second and third levels
of the tower.
• Attach a ramp assembly (sold
separately) to the middle level
to reach the ground.
LEVEL
2
• Use supports and straight
tracks (sold separately)
to build an elevated
assembly.
• Attach a ramp assembly to a support (each
sold separately) to reach the third level.
LEVEL
3
• Use two supports stacked up and straight
tracks (each sold separately) to build an
elevated assembly.
7
Chimes & Music!
• You do not need an Elevation Track Pack to utilize
the tower sound effect feature.
• Separate the tower into two parts, so the middle
level is now at ground level. When a train goes
through this level, you’ll also hear chimes
and music. (Track sold separately.)
SPIN
• Rotate the spinner
on the tower to
play a song.
The more
you collect,
the more
fun it gets!
Playsets and accessories sold separately and subject to availability.
Two of each Elevation Track Packs used to make this configuration.
8
|