Dell™ PowerVault™
DL2100 Systems
Hardware Owner’s
Manual
Contents
1
About Your System
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
11
Accessing System Features During Startup
Front Panel Features and Indicators
.
.
.
12
LCD Panel Features
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
15
16
16
Home Screen .
Setup Menu
.
.
View Menu .
Hard-Drive Indicator Patterns for RAID .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
17
20
21
.
.
.
.
.
.
Power Indicator Codes
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
NIC Indicator Codes .
.
LCD Status Messages .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
22
22
Removing LCD Status Messages
System Messages .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
36
52
52
52
53
Warning Messages
Diagnostics Messages
Alert Messages .
.
.
.
Other Information You May Need .
Contents
3
2
UEFI Boot Manager
55
Choosing the System Boot Mode
.
.
.
.
.
.
.
.
.
.
.
.
55
Entering the System Setup Program .
Responding to Error Messages
Using the System Setup Program
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
56
56
Navigation Keys
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
56
System Setup Options
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
60
61
62
63
63
64
65
66
67
Main Screen
.
.
Memory Settings Screen .
Processor Settings Screen .
SATA Settings Screen
.
.
.
.
.
.
Boot Settings Screen .
Integrated Devices Screen .
PCI IRQ Assignments Screen
Serial Communication Screen
Embedded Server Management Screen .
Power Management Screen .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
System Security Screen
Exit Screen .
.
.
.
.
.
.
.
.
.
.
.
.
Entering the UEFI Boot Manager
.
.
.
.
.
.
.
.
.
.
.
.
68
Using the UEFI Boot Manager
Navigation Keys
UEFI Boot Manager Screen
UEFI Boot Settings Screen .
System Utilities Screen .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
68
69
69
69
.
.
System and Setup Password Features
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
70
70
72
Using the System Password
.
.
.
.
.
.
Using the Setup Password .
4
Contents
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
73
Entering the iDRAC Configuration Utility .
74
3
Installing System Components
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
75
Recommended Tools
Inside the System
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
75
Front Bezel (Optional) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
77
Removing the Front Bezel
Installing the Front Bezel .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
78
Opening the System
.
.
.
.
.
.
.
.
Closing the System .
Information Tag
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
79
80
Removing the Information Tag .
Installing the Information Tag
.
Hard Drives
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
81
81
82
82
Removing a Hard-Drive Blank
.
Carrier
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
83
83
Installing a Hard Drive Into a Hard-Drive
Carrier
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Power Supplies
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
85
85
86
87
Removing a Power Supply .
Replacing a Power Supply .
Removing the Power Supply Blank
Contents
5
.
.
.
.
.
.
.
.
Internal SD Module
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
87
87
89
Installing the Internal SD Module
Internal SD Flash Card .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
89
Installing the Internal SD Flash Card .
Internal USB Memory Key .
Internal USB Cable
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
92
92
92
Removing the Internal USB Cable
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
93
Installing an iDRAC6 Enterprise Card
VFlash Media (Optional) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
95
95
NIC Hardware Key .
Cooling Shroud
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
97
97
98
Removing the Cooling Shroud
Cooling Fans .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
99
Removing a Cooling Fan
Replacing a Cooling Fan
100
100
102
Removing the Fan Bracket .
Replacing the Fan Bracket .
Optical Drive .
Removing the Optical Drive
Installing the Optical Drive .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
102
102
102
6
Contents
Removing the Integrated Storage Controller
Card
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
105
106
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Card
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
RAID Battery .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Removing a RAID Battery
Installing a RAID Battery .
Cable Routing
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
111
112
Removing the Cable Retention Bracket
Installing the Cable Retention Bracket
Expansion Cards and Expansion-Card Risers
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
113
116
117
119
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Removing Expansion-Card Riser 1 .
Expansion-Card Bracket .
.
.
.
.
.
.
.
.
.
.
.
.
.
Expansion-Card Bracket .
System Memory
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
121
.
.
.
.
.
.
.
.
122
General Memory Module Installation
Guidelines
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
122
124
127
129
Mode-Specific Guidelines .
Installing Memory Modules
Removing Memory Modules .
Processors .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
130
Removing a Processor .
130
Contents
7
Installing a Processor
System Battery .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Replacing the System Battery
Control Panel Assembly
136
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
138
138
Removing the Control Panel Display Module
.
.
.
.
.
.
.
.
.
.
SAS Backplane
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
141
142
Installing a SAS Backplane
System Board
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
143
145
Removing the System Board
Installing the System Board
4
Troubleshooting Your System
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
147
147
147
147
148
148
149
149
150
151
Safety First—For You and Your System
Troubleshooting System Startup Failure
.
.
.
.
.
.
.
.
.
Troubleshooting External Connections .
Troubleshooting the Video Subsystem
.
.
.
.
.
.
Troubleshooting a USB Device
.
.
.
.
.
.
.
.
Troubleshooting a Serial I/O Device
Troubleshooting a NIC .
.
.
.
.
.
.
.
.
.
.
Troubleshooting a Wet System
Troubleshooting a Damaged System
8
Contents
Troubleshooting the System Battery
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
152
152
153
154
154
156
157
158
159
160
161
162
Troubleshooting Power Supplies .
.
Troubleshooting System Cooling Problems .
Troubleshooting a Fan .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Troubleshooting System Memory .
Troubleshooting an Internal SD Card .
Troubleshooting an Internal USB Memory Key .
Troubleshooting an Optical Drive .
Troubleshooting a Hard Drive .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Troubleshooting a Storage Controller
Troubleshooting Expansion Cards
.
.
.
.
Troubleshooting the Processor(s) .
5
Running the System Diagnostics
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
165
165
165
166
167
Using Dell Online Diagnostics
.
.
.
.
.
.
.
.
.
.
.
.
.
Embedded System Diagnostics Features .
Running the Embedded System Diagnostics
.
.
.
.
Embedded System Diagnostics Testing Options
Using the Custom Test Options
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
167
167
167
168
Selecting Devices for Testing
Selecting Diagnostics Options .
Viewing Information and Results
Contents
9
6
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
169
System Board Jumpers
.
.
.
.
.
.
.
.
.
.
.
System Board Connectors .
172
SAS Backplane Board Connectors
175
Expansion-Card Riser-Board Components and
.
PCIe Buses .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
176
.
.
.
.
.
.
.
7
Getting Help
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
181
Contacting Dell
.
181
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Index
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
193
10
Contents
About Your System
Accessing System Features During Startup
The following keystrokes provide access to system features during startup.
Keystroke
Description
<F2>
Enters the System Setup program. See "Using the System Setup
Program and UEFI Boot Manager."
<F10>
Enters System Services, which opens the Unified Server Configurator
(USC) from which you can access utilities such as system diagnostics.
See the Unified Server Configurator user documentation for more
information.
NOTE: Some USC processing, such as software updates, can cause
virtual devices to be created that at times may appear as USB devices
attached to your system. These connections are both secure and
temporary, and can be disregarded.
<F11>
<F12>
Enters the BIOS Boot Manager or the UEFI Boot Manager,
depending on your system’s boot configuration. See "Using the
System Setup Program and UEFI Boot Manager."
Enters PXE boot, if enabled.
<Ctrl><E> Enters the iDRAC Configuration Utility, which allows access to the
system event log (SEL) and configuration of remote access to the
system. See the iDRAC user documentation for more information.
<Ctrl><C> Enters the SAS Configuration Utility. For more information, see the
documentation for your SAS controller.
<Ctrl><R> Enters the PERC Configuration Utility. For more information, see
the documentation for your PERC card.
<Ctrl><S> Enters the utility to configure NIC settings for PXE boot. For more
information, see the documentation for your embedded NIC.
About Your System
11
Front Panel Features and Indicators
Figure 1-1. Front Panel Features and Indicators
7
8
9
1
5
6
3
4
2
10
Item
Indicator, Button, or
Connector
Icon
Description
1
Information tag
A slide-out label panel for system
information including the Express
Service tag, Embedded NIC1 MAC
address, and iDRAC6 Enterprise card
MAC address.
12
About Your System
Item
Indicator, Button, or
Connector
Icon
Description
2
Power-on indicator,
power button
The power-on indicator lights when the
system power is on.
The power button controls the DC
power supply output to the system.
When the system bezel is installed, the
power button is not accessible.
NOTE: When powering on the system, the
video monitor can take up to 25 seconds
to display an image, depending on the
amount of memory installed in the system.
NOTE: On ACPI-compliant operating
systems, turning off the system using the
power button causes the system to
perform a graceful shutdown before
power to the system is turned off.
NOTE: To force an ungraceful shutdown,
press and hold the power button for five
seconds.
3
NMI button
Used to troubleshoot software and
device driver errors when using certain
operating systems. This button can be
pressed using the end of a paper clip.
Use this button only if directed to do so
by qualified support personnel or by the
operating system's documentation.
4
5
USB connectors (2)
Video connector
Connects USB devices to the system.
The ports are USB 2.0-complaint.
Connects a monitor to the system.
6
LCD menu buttons
Allows you to navigate the control panel
LCD menu.
About Your System
13
Item
Indicator, Button, or
Connector
Icon
Description
7
LCD panel
Provides system ID, status information,
and system error messages.
The LCD lights blue during normal
system operation. The LCD lights
amber when the system needs attention,
and the LCD panel displays an error
code followed by descriptive text.
NOTE: If the system is connected to AC
power and an error has been detected,
the LCD lights amber regardless of
whether the system has been powered on.
8
System identification
button
The identification buttons on the front
and back panels can be used to locate a
particular system within a rack. When
one of these buttons is pushed, the LCD
panel on the front and the system status
indicator on the back flash blue until
one of the buttons is pushed again.
9
Optical drive
One slim-line SATA DVD-ROM drive or
DVD+RW drive.
NOTE: DVD devices are data only.
10
Hard drives
Up to six 3.5-inch hot-swappable.
LCD Panel Features
The system's LCD panel provides system information and status messages to
signify when the system is operating correctly or when the system needs
attention. See "LCD Status Messages" for information on specific status
codes.
The LCD backlight lights blue during normal operating conditions and lights
amber to indicate an error condition. When the system is in standby mode,
the LCD backlight is off and can be turned on by pressing the Select button
on the LCD panel. The LCD backlight will remain off if LCD messaging is
turned off through the iDRAC utility, the LCD panel, or other tools.
14
About Your System
Figure 1-2. LCD Panel Features
1
2
3
4
Item
1
Buttons
Left
Description
Moves the cursor back in one-step increments.
2
Select
Selects the menu item highlighted by the
cursor.
3
Right
Moves the cursor forward in one-step
increments.
During message scrolling:
• Press once to increase scrolling speed.
• Press again to stop.
• Press again to return to default scrolling
speed.
• Press again to repeat the cycle.
4
System ID
Turns the system ID mode on and off.
Press quickly to toggle the system ID on and
off. If the system hangs during POST, press and
hold the system ID button for more than five
seconds to enter BIOS Progress mode.
Home Screen
The Home screen displays user-configurable information about the system.
This screen is displayed during normal system operation when there are no
status messages or errors present. When the system is in standby, the LCD
backlight turns off after five minutes of inactivity if there are no error
messages. Press one of the three navigation buttons (Select, Left, or Right) to
view the Home screen.
To navigate to the Home screen from another menu, continue to select the
up arrow until the Home icon
icon.
is displayed, and then select the Home
About Your System
15
From the Home screen, press the Select button to enter the main menu. See
the following tables for information on the Setup and View submenus.
Setup Menu
NOTE: When selecting an option in the Setup menu, you are asked to confirm the
option before you can continue.
Option
Description
DRAC
Select DHCP or Static IP to configure the network
mode. If Static IP is selected, the available fields are IP,
Subnet (Sub), and Gateway (Gtw). Select Setup DNS
to enable DNS and to view domain addresses. Two
separate DNS entries are available.
Set error
that matches the IPMI description in the SEL log. This
can be useful when trying to match an LCD message
with a SEL entry.
Select Simple to display LCD error messages in a
simplified, user-friendly description. See "LCD Status
Messages" for a list of messages in this format.
Set home
Select the default information to be displayed on the
LCD Home screen. See "View Menu" to see the options
and option items that can be selected to display by
default on the Home screen.
View Menu
Option
Description
DRAC IP
Displays the IPv4 or IPv6 addresses for the iDRAC6.
Addresses include DNS (Primary and Secondary),
Gateway, IP, and Subnet (IPv6 does not have Subnet).
MAC
Displays the MAC addresses for DRAC, iSCSIn, or
NETn.
Name
Displays the name of the Host, Model, or User String
for the system.
Number
Displays the Asset tag or the Service tag for the system.
16
About Your System
Option
Description
Power
Displays the power output of the system in BTU/hr or
Watts. The display format can be configured in the "Set
home" submenu of the Setup menu (see "Setup
Menu").
Temperature
Displays the temperature of the system in Celsius or
Fahrenheit. The display format can be configured in the
"Set home" submenu of the Setup menu (see "Setup
Menu").
Hard-Drive Indicator Patterns for RAID
Figure 1-3. Hard-Drive Indicators
1
2
1
drive-activity indicator (green)
2
drive-status indicator
About Your System
17
Drive-Status Indicator Pattern
(RAID Only)
Condition
Blinks green two times per
second
Identify drive/preparing for removal
Off
Drive ready for insertion or removal
NOTE: The drive status indicator remains off until all
hard drives are initialized after system power is
applied. Drives are not ready for insertion or removal
during this time.
Blinks green, amber, and off
Drive predicted failure
Drive failed
Blinks amber four times per
second
Blinks green slowly
Steady green
Drive rebuilding
Drive online
Back Panel Features and Indicators
Figure 1-4. Back Panel Features
1
2
3
4
5
6
15
14
13
12
11
10
9
8
7
18
About Your System
Item
Indicator, Button, or
Connector
Icon
Description
1
PCIe slot 1
PCI Express (Generation 2) x4-link
expansion slot (full-height, 30.99-cm
[12.2-in] length)
2
3
PCIe slot 2
PCIe slot 3
PCIe x4-link Gen 2 expansion slot
(low-profile, 24.13-cm [9.5-in] length)
PCIe x8-link Gen 2 expansion slot
(full-height, 24.13-cm [9.5-in] length)
or
optional PCIe x16-link Gen 2
expansion slot (full-height, 24.13-cm
[9.5-in]) (no slot 4 with this option)
4
PCIe slot 4
PCIe x8-link Gen 2 expansion slot
(full-height, 24.13-cm [9.5-in] length)
5
6
7
power supply 1 (PS1)
power supply 2 (PS2)
870-W or 570-W power supply
870-W or 570-W power supply
system identification
button
The identification buttons on the front
and back panels can be used to locate a
particular system within a rack. When
one of these buttons is pushed, the
LCD panel on the front and the system
status indicator on the back flash blue
until one of the buttons is pushed
again.
8
9
system status indicator
Provides a power on indicator for the
back of the system
system status indicator
connector
Connector for attaching a system
indicator extension cable that is used
on a cable management arm
10
11
Ethernet connectors
(4)
Integrated 10/100/1000 NIC connectors
USB connectors (2)
Connects USB devices to the system.
The ports are USB 2.0-complaint
About Your System
19
Item
12
Indicator, Button, or
Connector
Icon
Description
video connector
Connects a VGA display to the system
Connects a serial device to the system
13
serial connector
14
iDRAC6 Enterprise
port (optional)
Dedicated management port for the
optional iDRAC6 Enterprise card
15
VFlash media slot
(optional)
Connects an external SD memory card
for the optional iDRAC6 Enterprise
card
Power Indicator Codes
An LED indicator on the power button indicates when power is supplied to
the system and the system is operational.
Redundant power supplies have an indicator that shows whether power is
present or whether a power fault has occurred.
•
•
Not lit — AC power is not connected.
Green — In standby mode, indicates that a valid AC source is connected
to the power supply and that the power supply is operational. When the
system is on, also indicates that the power supply is providing DC power to
the system.
•
•
Amber — Indicates a problem with the power supply.
Alternating green and amber — When hot-adding a power supply,
indicates that the power supply is mismatched with the other power
supply (a High Output 870-W power supply and an Energy Smart 570-W
power supply are installed in the same system). Replace the power supply
that has the flashing indicator with a power supply that matches the
capacity of the other installed power supply.
CAUTION: When correcting a power supply mismatch, replace only the power
supply with the flashing indicator. Swapping the opposite power supply to make a
matched pair can result in an error condition and unexpected system shutdown. To
change from a High Output configuration to an Energy Smart configuration or vice
versa, you must power down the system.
20
About Your System
Indicator
Description
Link indicator is green
The NIC is connected to a valid network link at
1000 Mbps.
Link indicator is amber
The NIC is connected to a valid network link at
10/100 Mbps.
Activity indicator is green
blinking
Network data is being sent or received.
The LCD messages consist of brief text messages that refer to events recorded
in the System Event Log (SEL). For information on the SEL and configuring
system management settings, see the systems management software
documentation.
NOTE: If your system fails to boot, press the System ID button for at least five
seconds until an error code appears on the LCD. Record the code, then see "Getting
Help."
Viewing Status Messages
If a system error occurs, the LCD screen will turn amber. Press the Select
button to view the list of errors or status messages. Use the left and right
arrow buttons to highlight an error number, and press Select to view the error.
Removing LCD Status Messages
For faults associated with sensors, such as temperature, voltage, fans, and so
on, the LCD message is automatically removed when that sensor returns to a
normal state. For other faults, you must take action to remove the message
from the display:
•
Clear the SEL — You can perform this task remotely, but you will lose the
event history for the system.
•
Power cycle — Turn off the system and disconnect it from the electrical
outlet; wait approximately ten seconds, reconnect the power cable, and
restart the system.
NOTE: The following LCD status messages are displayed in the Simple format. See
“Setup Menu" to select the format in which the messages are displayed.
22
About Your System
Table 1-1. LCD Status Messages
Code Text
Cause
Corrective Actions
E1000 Failsafe
voltage
Check the system event log Remove AC power to the
for critical failure events.
system for 10 seconds and
restart the system.
error.
Contact
support.
If the problem persists,
see "Getting Help."
E1114 Ambient Temp Ambient temperature has a See "Troubleshooting
exceeds
allowed
range.
reached a point outside of System Cooling
the allowed range.
Problems."
E1116 Memory
disabled,
Memory has exceeded
Remove AC power to the
allowable temperature and system for 10 seconds and
temp above
has been disabled to
restart the system.
range. Power prevent damage to the
See "Troubleshooting
System Cooling
cycle AC.
components.
Problems." If the problem
persists, see "Getting
Help."
E1210 Motherboard
battery
CMOS battery is missing or See "Troubleshooting the
the voltage is outside of the System Battery."
allowable range.
failure.
Check
battery.
E1211 RAID
Controller
battery
RAID battery is either
Reseat the RAID battery
missing, bad, or unable to connector. See "Installing
recharge due to thermal
issues.
a RAID Battery" and
"Troubleshooting System
Cooling Problems."
failure.
Check
battery.
E1216 3.3V
Regulator
failure.
3.3V voltage regulator has Remove and reseat the
failed.
PCIe expansion cards. If
the problem persists, see
"Troubleshooting
Reseat PCIe
cards.
Expansion Cards."
About Your System
23
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1229 CPU # VCORE
Regulator
Specified processor
Reseat the processor(s).
VCORE voltage regulator See "Troubleshooting the
failure.
has failed.
Processor(s)."
Reseat CPU.
If the problem persists,
see "Getting Help."
E122A CPU # VTT
Regulator
Specified processor VTT
Reseat the processor(s).
voltage regulator has failed. See "Troubleshooting the
Processor(s)."
failure.
Reseat CPU.
If the problem persists,
see "Getting Help."
E122C CPU Power
cycle AC.
A power fault was detected Remove AC power to the
Fault. Power when powering up the
processor(s).
system for 10 seconds and
restart the system.
If the problem persists,
see "Getting Help."
E122D Memory
Regulator #
Failed.
One of the memory
regulators has failed.
Reseat the memory
modules. See
"Troubleshooting System
Memory."
Reseat DIMMs.
E122E On-board
regulator
One of the on-board
Remove AC power to the
system for 10 seconds and
restart the system.
voltage regulators failed.
failed. Call
support.
If the problem persists,
see "Getting Help."
E1310 Fan ## RPM
exceeding
RPM of specified fan is
outside of the intended
See "Troubleshooting
System Cooling
Problems."
range. Check operating range.
fan.
E1311 Fan module ## RPM of specified fan in
See "Troubleshooting
RPM exceeding specified module is outside System Cooling
range. Check of intended operating Problems."
fan.
range.
24
About Your System
Table 1-1. LCD Status Messages (continued)
Code
E1313 Fan
redundancy
Text
Cause
Corrective Actions
The system is no longer fan Check LCD for additional
redundant. Another fan
failure would put the
system at risk of
scrolling messages. See
"Troubleshooting a Fan."
lost. Check
fans.
over-heating.
E1410 System Fatal A fatal system error has
Check LCD for additional
scrolling messages.
Error
been detected.
detected.
Remove AC power to the
system for 10 seconds and
restart the system.
If the problem persists,
see "Getting Help."
E1414 CPU # temp
exceeding
Specified processor is out of Ensure that the processor
acceptable temperature
heat sinks are properly
installed. See
range. Check range.
CPU heatsink.
"Troubleshooting the
Processor(s)" and
"Troubleshooting System
Cooling Problems."
E1418 CPU # not
detected.
Specified processor is
missing or bad, and the
Ensure that the specified
processor is properly
Check CPU is system is in an unsupported installed. See
seated
configuration.
"Troubleshooting the
properly.
Processor(s)."
E141C Unsupported
Processors are in an
Ensure that your
CPU configur- unsupported configuration. processors match and
ation. Check
CPU or BIOS
revision.
conform to the type
described in the processor
technical specifications
outlined in your system’s
Getting Started Guide.
E141F CPU #
protocol
The system BIOS has
reported a processor
Remove AC power to the
system for 10 seconds and
restart the system.
error. Power protocol error.
cycle AC.
If the problem persists,
see "Getting Help."
About Your System
25
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1420 CPU Bus
The system BIOS has
Remove AC power to the
system for 10 seconds and
restart the system.
parity error. reported a processor bus
Power cycle
AC.
parity error.
If the problem persists,
see "Getting Help."
E1422 CPU # machine The system BIOS has
Remove AC power to the
check error. reported a machine check system for 10 seconds and
Power cycle
AC.
error.
restart the system.
If the problem persists,
see "Getting Help."
E1610 Power Supply Specified power supply was See "Troubleshooting
# (### W)
missing.
Check power
supply.
removed or is missing from Power Supplies."
the system.
E1614 Power Supply Specified power supply has See "Troubleshooting
# (### W)
failed.
Power Supplies
error. Check
power supply.
E1618 Predictive
failure on
A power supply fan failure, See "Troubleshooting
an over-temperature
Power Supplies."
Power Supply condition, or power supply
# (### W).
Check PSU.
communication error has
caused the predictive
warning of an impending
power supply failure.
E161C Power Supply Specified power supply is
Check the AC power
# (### W)
lost AC
power. Check
PSU cables.
attached to the system, but source for the specified
it has lost its AC input.
power supply. If the
problem persists, see
"Troubleshooting Power
Supplies."
26
About Your System
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1620 Power Supply Specified power supply's
Check the AC power
# (### W) AC AC input is outside of the source for the specified
power error. allowable range.
Check PSU
cables.
power supply. If the
problem persists, see
"Troubleshooting Power
Supplies."
E1624 Lost power
The power supply
See "Troubleshooting
Power Supplies."
supply
subsystem is no longer
redundant. If the remaining
power supply fails, the
system will shut down.
redundancy.
Check PSU
cables.
E1626 Power Supply The power supplies in the Ensure that power
Mismatch.
PSU1 = ### W, wattage.
PSU2 = ### W.
system are not the same
supplies with matching
wattage are installed. See
the technical
specifications outlined in
your system’s Getting
Started Guide.
E1629 Power
required >
The system configuration Turn off power to the
requires more power than system, reduce the
PSU wattage. the power supplies can
Check PSU and provide, even with
hardware configuration or
install higher-wattage
power supplies, and then
restart the system.
config.
throttling.
E1710 I/O channel
The system BIOS has
Check the SEL for more
information and then
clear the SEL. Remove
AC power to the system
for 10 seconds and restart
the system.
check error. reported an I/O channel
Review &
clear SEL.
check.
If the problem persists,
see "Getting Help."
About Your System
27
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1711 PCI parity
The system BIOS has
Remove and reseat the
error on Bus reported a PCI parity error PCIe expansion cards. If
## Device ## on a component that the problem persists, see
"Troubleshooting
Function ##
resides in PCI
configuration space at bus Expansion Cards."
##, device ##, function
##.
PCI parity
The system BIOS has
Remove and reseat the
error on Slot reported a PCI parity error PCIe expansion cards. If
#. Review &
clear SEL.
on a component that
resides in the specified slot. "Troubleshooting
Expansion Cards."
the problem persists, see
E1712 PCI system
The system BIOS has
Remove and reseat the
error on Bus reported a PCI system error PCIe expansion cards. If
## Device ## on a component that the problem persists, see
"Troubleshooting
Function ##
resides in PCI
configuration space at bus Expansion Cards."
##, device ##, function
##.
PCI system
The system BIOS has
Reinstall the
error on Slot reported a PCI system error expansion-card riser. See
#. Review &
clear SEL.
on a component that
"Expansion Cards and
resides in the specified slot. Expansion-Card Risers." If
the problem persists, the
riser card or system board
is faulty. See "Getting
Help."
E1714 Unknown
The system BIOS has
Check the SEL for more
error. Review determined there has been information and then
& clear SEL. an error in the system, but clear the SEL. Remove
is unable to determine its AC power to the system
origin.
for 10 seconds and restart
the system.
If the problem persists,
see "Getting Help."
28
About Your System
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1715 Fatal I/O
The system BIOS has
Check the SEL for more
Error. Review determined there has been information, and then
& clear SEL. a fatal error in the system. clear the SEL. Remove
AC power to the system
for 10 seconds, and restart
the system.
If the problem persists,
see "Getting Help."
E1716 Chipset IERR The system BIOS has
Bus ## Dev ## reported a chipset internal information, and then
Function ##. error that resides in bus clear the SEL. Remove
##, device ##, function AC power to the system
Check the SEL for more
Review &
clear SEL.
##.
for 10 seconds, and restart
the system.
If the problem persists,
see "Getting Help."
E1717 CPU #
internal
The system BIOS has
determined that the
Check the SEL for more
information, and then
error. Review specified processor has had clear the SEL. Remove
& clear SEL. an internal error.
AC power to the system
for 10 seconds, and restart
the system.
If the problem persists,
see "Getting Help."
About Your System
29
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E171F PCIe fatal
The system BIOS has
Remove and reseat the
error on Bus reported a PCIe fatal error PCIe expansion cards. If
## Device ## on a component that the problem persists, see
"Troubleshooting
Function ##
resides in PCI
configuration space at bus Expansion Cards."
##, device ##, function
##.
PCIe fatal
The system BIOS has
Reinstall the
error on Slot reported a PCIe fatal error expansion-card riser. See
#. Review &
clear SEL.
on a component that
"Expansion Cards and
resides in the specified slot. Expansion-Card Risers." If
the problem persists, the
riser card or system board
is faulty. See "Getting
Help."
E1810 Hard drive ## The specified hard drive
fault. Review has experienced a fault.
& clear SEL.
See "Troubleshooting a
Hard Drive."
E1812 Hard drive ## The specified hard drive
Information only.
removed.
has been removed from the
Check drive. system.
E1A11 PCI Riser PCIe risers are not
hardware & configured correctly. Some expansion-card riser. See
configuration invalid configurations
mismatch. prevent the system from
Reinstall the
"Expansion Cards and
Expansion-Card Risers."
Reconfigure. powering on.
If the problem persists,
the riser card or system
board is faulty. See
"Getting Help."
E1A12 PCI Riser not One or both of the PCIe
Reinstall the missing riser
card(s). See "Removing
Expansion-Card Riser 2"
and "Replacing
detected.
risers are missing. This
Check Riser. prevents the system from
powering on.
Expansion-Card Riser 2."
30
About Your System
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E1A14 SAS cable A
failure.
SAS cable A is missing or
bad.
Reseat the cable. If the
problem persists, replace
cable.
Check
connection.
If the problem persists,
see "Getting Help."
E1A15 SAS cable B
failure.
SAS cable B is missing or
bad.
Reseat the cable. If the
problem persists, replace
cable.
Check
connection.
If the problem persists,
see "Getting Help."
E1A1D Control panel USB cable to the control
USB cable not panel is missing or bad.
detected.
Reseat the cable. If the
problem persists, replace
cable.
Check cable.
If the problem persists,
see "Getting Help."
E2010 Memory not
detected.
Inspect
No memory was detected in Install memory or reseat
the system.
the memory modules. See
"Installing Memory
Modules" or
DIMMs.
"Troubleshooting System
Memory."
E2011 Memory
Memory detected, but is
See "Troubleshooting
System Memory."
configuration not configurable. Error
failure. detected during memory
Check DIMMs. configuration.
E2012 Memory Memory configured, but is See "Troubleshooting
configured unusable. System Memory."
but unusable.
Check DIMMs.
E2013 BIOS unable
to shadow
The system BIOS failed to See "Troubleshooting
copy its flash image into
System Memory."
memory. Check memory.
DIMMs.
About Your System
31
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E2014 CMOS RAM
failure.
CMOS failure. CMOS
RAM not functioning
properly.
Remove AC power to the
system for 10 seconds and
restart the system.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E2015 DMA
DMA controller failure.
Remove AC power to the
system for 10 seconds and
restart the system.
Controller
failure.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E2016 Interrupt
Controller
failure.
Interrupt controller failure. Remove AC power to the
system for 10 seconds and
restart the system.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E2017 Timer refresh Timer refresh failure.
Remove AC power to the
system for 10 seconds and
restart the system.
failure.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E2018 Programmable Programmable interval
Remove AC power to the
system for 10 seconds and
restart the system.
Timer error. timer error.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E2019 Parity error. Parity error.
Remove AC power to the
system for 10 seconds and
restart the system.
Power cycle
AC.
If the problem persists,
see "Getting Help."
32
About Your System
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
E201A SuperIO
failure.
SIO failure.
Remove AC power to the
system for 10 seconds and
restart the system.
Power cycle
AC.
If the problem persists,
see "Getting Help."
E201B Keyboard
Controller
Keyboard controller failure. Remove AC power to the
system for 10 seconds and
error. Power
cycle AC.
restart the system.
If the problem persists,
see "Getting Help."
E201C SMI
System management
Remove AC power to the
system for 10 seconds and
restart the system.
initializatio interrupt (SMI)
n failure.
Power cycle
AC.
initialization failure.
If the problem persists,
see "Getting Help."
E201D Shutdown test BIOS shutdown test failure. Remove AC power to the
failure.
Power cycle
AC.
system for 10 seconds and
restart the system.
If the problem persists,
see "Getting Help."
E201E POST memory
Check DIMMs.
BIOS POST memory test See "Troubleshooting
test failure. failure.
System Memory."
If the problem persists,
see "Getting Help."
E2020 CPU
Processor configuration
Check screen for specific
error messages. See
"Troubleshooting the
Processor(s)."
configuration failure.
failure.
Check screen
message.
E2021 Incorrect
Incorrect memory
configuration.
Check screen for specific
error messages. See
"Troubleshooting System
Memory".
memory
configur-
ation. Review
User Guide.
About Your System
33
Table 1-1. LCD Status Messages (continued)
Code Text Cause
Corrective Actions
E2022 General
failure
General failure after video. Check screen for specific
error messages.
during POST.
Check screen
message.
E2023 BIOS unable
to mirror
The system BIOS could not See "Troubleshooting
enable memory mirroring System Memory."
memory. Check because of a faulty memory
DIMMs.
module or an invalid
memory configuration.
E2110 Multibit
The memory module in slot See "Troubleshooting
Error on DIMM "##" has had a multi-bit
System Memory."
##. Reseat
DIMM.
error (MBE).
E2111 SBE log
disabled on
DIMM ##.
The system BIOS has
Remove AC power to the
disabled memory single-bit system for 10 seconds and
error (SBE) logging and will restart the system.
Reseat DIMM. not log any more SBEs until
If the problem persists,
see "Troubleshooting
System Memory."
the system is rebooted.
"##" represents the
memory module implicated
by the BIOS.
E2113 Mem mirror
OFF on DIMM
## & ##.
The system BIOS has
Remove AC power to the
disabled memory mirroring system for 10 seconds and
because it has determined restart the system.
Power cycle
AC.
one half of the mirror has
If the problem persists,
had too many errors. "##
see "Troubleshooting
& ##" represents the
System Memory."
memory module pair
implicated by the BIOS.
I1910 Intrusion
detected.
System cover has been
removed.
Information only.
Check chassis
cover.
34
About Your System
Table 1-1. LCD Status Messages (continued)
Code
Text
Cause
Corrective Actions
I1911 LCD Log Full. LCD overflow message. A Check the SEL for details
Check SEL to maximum of ten error
on the events.
review all
Errors.
messages can display
sequentially on the LCD.
The eleventh message
instructs the user to check
the SEL for details on the
events.
Remove AC power to the
system for 10 seconds or
clear the SEL.
I1912 SEL full.
Review &
The SEL is full of events
and is unable to log any
more.
Check the SEL for more
information and then
clear the SEL.
clear log.
W1228 RAID
Controller
battery
Warns predictively that the Allow RAID battery to
RAID battery has less than charge to greater than 24
24 hours of charge left.
hours of sustained charge.
capacity <
24hr.
If problem persists,
replace the RAID battery.
See "Installing a RAID
Battery."
W1627 Power
required >
The system configuration Turn off power to the
requires more power than system, reduce the
PSU wattage. what the power supply can hardware configuration or
Check PSU and provide.
config.
install higher-wattage
power supplies, and then
restart the system.
W1628 Performance
degraded.
The system configuration Turn off power to the
requires more power than system, reduce the
Check PSU and what the power supply can hardware configuration or
system
configur-
ation.
provide, but it can boot if install higher-wattage
throttled. power supplies, and then
restart the system.
NOTE: For the full name of an abbreviation or acronym used in this table, see "Glossary."
About Your System
35
System Messages
System messages appear on the screen to notify you of a possible problem
with the system.
NOTE: If you receive a system message not listed in the table, check the
documentation for the application that is running when the message appears or the
operating system's documentation for an explanation of the message and
recommended action.
Table 1-2. System Messages
Message
Causes
Corrective Actions
128-bit Advanced The Advanced ECC option Check other messages for a
ECC mode
was enabled in BIOS, but is faulty memory module.
disabled. For
no longer valid due to an
Reconfigure the memory
128-bit Advanced unsupported memory
modules for Advanced ECC
mode. See "System Memory."
ECC, DIMMs must
be installed in
configuration, possibly a
faulty or removed memory
pairs. Pairs must module. The Advanced ECC
be matched in
size and
setting has been disabled.
geometry.
Alert! Advanced
ECC Memory Mode
Advanced ECC Memory
Mode was enabled in the
Ensure that the memory
modules are installed in a
configuration the current configuration Advanced ECC Memory
Advanced ECC
Memory Mode.
ECC Memory Mode. A
memory module may be
faulty.
messages for additional
information for possible
causes. For memory
configuration information,
see "General Memory
Module Installation
Guidelines." If the problem
persists, see
"Troubleshooting System
Memory."
36
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Alert! iDRAC6 not The iDRAC6 is not
Wait for the system to
reboot.
responding.
Rebooting.
responding to BIOS
communication either
because it is not functioning
properly or has not
completed initialization.
The system will reboot.
Alert! iDRAC6 not The iDRAC6 is hung.
Remove AC power to the
system for 10 seconds and
restart the system.
responding.
The iDRAC6 was remotely
Power required
reset while system was
may exceed PSU
booting
wattage.
After AC recovery, the
Alert!
iDRAC6 takes longer than
Continuing
normal to boot.
system boot
accepts the risk
that system may
power down
without warning.
Alert! Node
Interleaving
disabled! Memory interleaving, or the
configuration
does not support (for example, a memory
The memory configuration Ensure that the memory
does not support node
modules are installed in a
configuration that supports
node interleaving. Check
other system messages for
additional information for
configuration has changed
Node
module has failed) so that
Interleaving.
node interleaving cannot be possible causes. For memory
supported. The system will configuration information,
run but without node
interleaving.
see "General Memory
Module Installation
Guidelines." If the problem
persists, see
"Troubleshooting System
Memory."
About Your System
37
Alert! Power
required exceeds
PSU wattage.
Check PSU and
system
configuration.
Alert!
Continuing
system boot
accepts the risk
that system may
38
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
BIOS Update
Attempt Failed!
Remote BIOS update
attempt failed.
Retry the BIOS update. If
problem persists, see
"Getting Help."
Caution!
NVRAM_CLR jumper is
Move the NVRAM_CLR
NVRAM_CLR jumper installed in the clear setting. jumper to the default
is installed on
system board
CMOS has been cleared.
position (pins 3 and 5). See
Figure 6-1 for jumper
location. Restart the system
and re-enter the BIOS
settings. See "Using the
System Setup Program and
UEFI Boot Manager."
CPU set to
minimum
frequency.
The processor speed may be If not an intentional setting,
intentionally set lower for
power conservation.
check any other system
messages for possible causes.
CPU x installed
Memory modules are
Install memory modules for
with no memory.
required but not installed in the processor. See "System
the indicated processor’s Memory."
memory slots.
CPUs with
different cache
sizes detected.
Mismatched processors have Ensure that all processors
been installed in the system. have the same cache size,
number of cores and logical
processors, and power rating.
CPUs with
Ensure that the processors
different core
sizes detected!
System halted
are properly installed. See
"Processors."
CPUs with
different
logical
processors
detected! System
halted
CPUs with
different power
rating detected!
System halted
About Your System
39
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Current boot mode The system failed to boot
Ensure that the boot mode is
is set to UEFI.
Please ensure
compatible
bootable media is non-UEFI.
available. Use
because UEFI boot mode is set correctly and that the
enabled in BIOS and the
boot operating system is
proper bootable media is
available. See "Using the
System Setup Program and
UEFI Boot Manager."
the system setup
program to change
the boot mode as
needed.
Decreasing
Faulty or improperly
Reseat the memory modules.
available memory installed memory modules. See "Troubleshooting System
Memory."
DIMM
Invalid memory
Ensure that the memory
modules are installed in a
dual-processor system. The valid configuration. See
configuration on configuration on a
each CPU should
match.
memory module
"General Memory Module
Installation Guidelines."
configuration for each
processor must be identical.
Embedded NICx and The OS NIC interface is set Check the system
NICy:
in BIOS. The Management management software or the
OS NIC=<ENABLED
|DISABLED>,
Management
Shared NIC=
<ENABLED
Shared NIC interface is set System Setup program for
in management tools.
NIC settings. If a problem is
indicated, see
"Troubleshooting a NIC."
|DISABLED>
Error 8602 -
Mouse or keyboard cable is Reseat the mouse or
Auxiliary Device loose or improperly
keyboard cable.
Failure. Verify
that mouse and
keyboard are
securely
attached to
correct
connected.
Defective mouse or
keyboard.
Ensure that the mouse or
keyboard is operational. See
"Troubleshooting a USB
Device."
connectors.
40
About Your System
Table 1-2. System Messages (continued)
Message
Gate A20 failure Faulty keyboard controller; See "Getting Help."
faulty system board.
Causes
Corrective Actions
General failure
The operating system is
unable to carry out the
command.
This message is usually
followed by specific
information. Note the
information, and take the
appropriate action to resolve
the problem.
Invalid
An invalid system
configuration caused a
system halt.
Run the System Setup
configuration
information -
please run SETUP
program.
program and review the
current settings. See "Using
the System Setup Program
and UEFI Boot Manager."
Invalid PCIe card The system halted because Remove the PCIe expansion
found in the an invalid PCIe expansion card and install the
Internal_Storage card is installed in the integrated storage controller
dedicated storage controller in the dedicated slot. See
slot. "Integrated Storage
Controller Card."
slot!
Keyboard
controller
failure
Faulty keyboard controller; See "Getting Help."
faulty system board
Keyboard data
line failure
Keyboard cable connector is Reseat the keyboard cable. If
improperly connected or the the problem persists, see
keyboard is defective.
"Troubleshooting a USB
Device."
Keyboard stuck
key failure
Keyboard fuse has Overcurrent detected at the See "Getting Help."
failed keyboard connector.
About Your System
41
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Local keyboard
may not work
because all user
accessible USB
ports are
The USB ports are disabled Power down and restart the
in the system BIOS.
system from the power
button, and then enter the
System Setup program to
enable the USB port(s). See
"Entering the System Setup
Program."
disabled. If
operating
locally, power
cycle the system
and enter system
setup program to
change settings.
Manufacturing
mode detected
mode.
out of manufacturing mode.
Maximum rank
count exceeded.
The following
DIMM has been
disabled: x
Invalid memory
Ensure that the memory
modules are installed in a
valid configuration. See
Installation Guidelines."
configuration. The system
will run but with the
specified memory module
disabled.
Memory address
line failure at
address, read
value expecting
value
Faulty or improperly
See "Troubleshooting System
installed memory modules. Memory."
Memory double
word logic
Faulty or improperly
See "Troubleshooting System
installed memory modules. Memory."
failure at
address, read
value expecting
value
Memory
Invalid memory
Ensure that the memory
Initialization
Warning: Memory
size may be
reduced
configuration. The system
will run but with less
memory than is physically
available.
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines."
42
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Memory odd/even
Faulty or improperly
See "Troubleshooting System
logic failure at installed memory modules. Memory."
address, read
value expecting
value
Memory
Faulty or improperly
See "Troubleshooting System
write/read
failure at
address, read
value expecting
value
installed memory modules. Memory."
Memory set to
minimum
The memory frequency may If not an intentional setting,
be intentionally set lower for check any other system
frequency.
power conservation.
The current memory
messages for possible causes.
Ensure that your memory
configuration may support configuration supports the
only the minimum
frequency.
higher frequency. See
"General Memory Module
Installation Guidelines."
Memory tests
terminated by
keystroke.
POST memory test was
terminated by pressing the
spacebar.
Information only.
Invalid memory
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines."
MEMTEST lane
failure
detected on x
configuration. A
mismatched memory
module is installed.
Mirror mode
disabled. For
mirror mode,
DIMMs must be
installed in
pairs. Pairs must
be matched in
size and
The memory configuration Reconfigure the memory
does not match the setting modules for Memory
in BIOS. The BIOS setting Mirroring mode. See "System
has been disabled.
Memory."
geometry.
About Your System
43
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
No boot device
available
Faulty or missing optical
or hard-drive subsystem, or persists, see
no bootable USB key
installed.
"Troubleshooting an Internal
SD Card," "Troubleshooting
a USB Device,"
"Troubleshooting an Optical
Drive," and "Troubleshooting
a Hard Drive." See "Using the
System Setup Program and
UEFI Boot Manager" for
information on setting the
order of boot devices.
No boot sector on Incorrect configuration
Check the hard-drive
hard drive
settings in System Setup
program, or no operating
system on hard drive.
configuration settings in the
System Setup program. See
"Using the System Setup
Program and UEFI Boot
Manager." If necessary, install
the operating system on your
hard drive. See your
operating system
documentation.
No timer tick
interrupt
Faulty system board.
See "Getting Help."
PCI BIOS failed
to install
PCIe device BIOS (Option Reseat the expansion card(s).
ROM) checksum failure Ensure that all appropriate
detected during shadowing. cables are securely connected
to the expansion card(s). If
Cables to expansion card(s)
the problem persists, see
loose; faulty or improperly
"Troubleshooting Expansion
installed expansion card(s).
Cards."
PCIe Training
Error: Expected
Link Width is x, specified slot.
Actual Link Width
is y.
Faulty or improperly
installed PCIe card in the
Reseat the PCIe card in the
specified slot number. See
"Troubleshooting Expansion
Cards." If the problem
persists, see "Getting Help."
44
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Plug & Play
Configuration
Error
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper in the clear position
(pins 1 and 3) and reboot the
system. See Figure 6-1 for
jumper location. If the
problem persists, see
"Troubleshooting Expansion
Cards."
Quad rank DIMM
detected after
single rank or
dual rank DIMM in
socket.
Invalid memory
configuration.
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines."
Read fault
read from the hard drive, USB medium or device.
Requested sector
not found
optical drive, or USB device, Ensure that the SAS
the system could not find a backplane, USB, or SATA
particular sector on the disk, cables are properly
or the requested sector is
defective.
connected. See
"Troubleshooting a USB
Device," "Troubleshooting an
Optical Drive," or
"Troubleshooting a Hard
Drive" for the appropriate
drive(s) installed in your
system.
SATA Portx device There is no device connected Information only.
not found to the specified SATA port.
About Your System
45
Table 1-2. System Messages (continued)
Message
Causes
The drive connected to the Replace the faulty drive.
specified SATA port is faulty.
Corrective Actions
SATA port x
device auto-
sensing error
SATA port x
device
configuration
error
SATA port x
device error
Sector not found Faulty hard drive, USB
device, or USB medium.
Replace the USB medium or
device. Ensure that the USB
or SAS backplane cables are
properly connected. See
"Troubleshooting a USB
Device" or "Troubleshooting
a Hard Drive" for the
Seek error
Seek operation
failed
appropriate drive(s) installed
in your system.
Shutdown failure General system error.
See "Getting Help."
The amount of
system memory has removed or a memory
changed module may be faulty.
Memory has been added or If memory has been added or
removed, this message is
informative and can be
ignored. If memory has not
been added or removed,
check the SEL to determine
if single-bit or multi-bit
errors were detected and
replace the faulty memory
module. See
"Troubleshooting System
Memory."
46
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
The following
DIMMs should
match in
geometry:
x,x,...
Invalid memory
Ensure that the memory
configuration. The specified modules are installed in a
memory modules do not
match in size, number of
ranks, or number of data
lanes.
valid configuration. See
"General Memory Module
Installation Guidelines."
The following
DIMMs should
match in rank
count: x,x,...
The following
DIMMs should
match in size:
x,x,...
The following
DIMMs should
match in size
and geometry:
x,x,...
The following
DIMMs should
match in size
and rank count:
x,x,...
Thermal sensor
not detected on x thermal sensor is installed in See "System Memory."
the specified memory slot
Time-of-day
clock stopped
Faulty battery or faulty chip. See "Troubleshooting the
System Battery."
Time-of-day not
set - please run settings; faulty system
SETUP program battery.
Incorrect Time or Date
Check the Time and Date
settings. See "Using the
System Setup Program and
UEFI Boot Manager." If the
problem persists, replace the
system battery. See "System
Memory."
About Your System
47
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Timer chip
Faulty system board.
See "Getting Help."
counter 2 failed
TPM
A TPM configuration
Information only.
configuration
operation
honored. System
will now reset.
command has been entered.
The system will reboot and
execute the command.
TPM
This message displays during Enter Ior Mto proceed.
system restart after a TPM
configuration
operation is
pending. Press
configuration command has
been entered. User
(I) to Ignore OR interaction is required to
(M) to Modify to proceed.
allow this change
and reset the
system.
WARNING:
Modifying could
prevent
security.
TPM failure
A Trusted Platform Module See "Getting Help."
(TPM) function has failed.
48
About Your System
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Unable to launch System halted after F10
Restart the system and
update the Unified Server
Configurator repository to
the latest software to restore
full functionality. See the
Unified Server Configuration
user documentation for more
information.
System Services
image. System
halted!
keystroke because System
Services image is either
corrupted in the system
firmware or has been lost
due to system board
replacement.
The iDRAC6 Enterprise card Restore the flash memory
flash memory may be
corrupted.
using the latest version on
support.dell.com. See the
iDRAC6 user's guide for
instructions on performing a
field replacement of the flash
memory.
Unexpected
Improperly seated memory Reseat the memory modules.
interrupt in
protected mode
modules or faulty
keyboard/mouse controller
chip.
See "Troubleshooting System
Memory." If the problem
persists, see "Getting Help."
Unsupported CPU
combination
by the system.
or processor combination.
See "Processors."
Unsupported CPU
stepping
detected
Unsupported DIMM Invalid memory
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines."
detected. The
following DIMM
has been
configuration. The system
will run but with the
specified memory module
disabled.
disabled: x
Unsupported
memory
Invalid memory
Ensure that the memory
modules are installed in a
configuration. Memory
configuration.
DIMM mismatch
across slots
detected:
modules are mismatched in valid configuration. See
the specified slots.
"General Memory Module
Installation Guidelines."
x,x,...
About Your System
49
Table 1-2. System Messages (continued)
Message
Causes
Corrective Actions
Unused memory
The memory configuration is Reconfigure the memory for
detected. DIMM’s not optimal for mirroring or Memory Mirroring or
installed in the Advanced ECC Memory
following slot Mode. Modules in the
are not available specified slots are unused.
when in mirror or
Advanced ECC Memory
Mode, or change the memory
mode to Optimized in the
BIOS setup screen. See
"System Memory."
128-bit advanced
ECC modes: x,x,x
Warning: A fatal A fatal system error occurred Check the SEL for
error has caused and caused the system to information that was logged
system reset!
Please check the
system event log!
reboot.
during the error. See the
applicable troubleshooting
section in "Troubleshooting
Your System" for any faulty
components specified in the
SEL.
Warning: Control The control panel is not
Install the control panel, or
Panel is not
installed.
installed or has a faulty cable check the cable connections
connection.
between the display module,
the control panel board, and
the system board. See
"Control Panel Assembly."
Warning! No micro Micro code update failed.
code update
Update the BIOS firmware.
See "Getting Help."
loaded for
processor n
50
About Your System
Table 1-2. System Messages (continued)
Message
Causes
The system configuration of If any system components
were just upgraded, return
the system to the previous
cards may not be supported configuration. If the system
Corrective Actions
Warning! Power
required exceeds processor(s), memory
PSU wattage.
Check PSU and
system
modules, and expansion
by the power supplies.
then the replaced
configuration.
component(s) are not
supported with this power
supply. If Energy Smart
power supplies are installed,
replace them with High
Output power supplies to use
the components. See "Power
Supplies."
Warning!
Performance
degraded. CPU and
memory set to
minimum
frequencies to
meet PSU wattage.
System will
reboot.
Warning! PSU
mismatch. PSU
A High Output power supply Install two High Output or
and an Energy Smart power two Energy Smart power
redundancy lost. supply are installed in the
supplies in the system.
Check PSU.
system at the same time.
You can also run the system
on one power supply until
you can obtain two power
supplies of the same type.
See "Troubleshooting Power
Supplies."
Warning!
Unsupported
memory
configuration
detected. The
memory
configuration is
not optimal. The
recommended
memory
Invalid memory
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines." If
the problem persists, see
"Troubleshooting System
Memory."
configuration. The system
will run but with reduced
functionality.
configuration
is: <message>
About Your System
51
Warning Messages
A warning message alerts you to a possible problem and prompts you to
respond before the system continues a task. For example, before you format a
drive, a message will warn you that you may lose all data on the drive.
Warning messages usually interrupt the task and require you to respond by
typing y(yes) or n(no).
NOTE: Warning messages are generated by either the application or the operating
system. For more information, see the documentation that accompanied the
operating system or application.
Diagnostics Messages
The system diagnostic utilities may issue messages if you run diagnostic tests
on your system. See "Running the Embedded System Diagnostics" for more
information about system diagnostics.
Alert Messages
Systems management software generates alert messages for your system. Alert
messages include information, status, warning, and failure messages for drive,
52
About Your System
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with your
system. Warranty information may be included within that document or as a
separate document.
•
•
•
The rack documentation included with your rack solution describes how to
install your system into a rack.
The Getting Started Guide provides an overview of system features, setting
up your system, and technical specifications.
Any media that ships with your system that provides documentation and
tools for configuring and managing your system, including those
pertaining to the operating system, system management software, system
updates, and system components that you purchased with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
About Your System
53
54
About Your System
Using the System Setup Program
and UEFI Boot Manager
The System Setup program is the BIOS program that enables you to manage
your system hardware and specify BIOS-level options. From the System Setup
program, you can:
•
•
•
•
•
Change the NVRAM settings after you add or remove hardware
View the system hardware configuration
Enable or disable integrated devices
Set performance and power management thresholds
Manage system security
Choosing the System Boot Mode
The System Setup program also enables you to specify the boot mode for
installing your operating system:
•
•
BIOS boot mode (the default) is the standard BIOS-level boot interface.
UEFI boot mode is an enhanced 64-bit boot interface based on Unified
Extensible Firmware Interface (UEFI) specifications that overlays the
system BIOS. See "Entering the UEFI Boot Manager" for more
information on this interface.
You select the boot mode in the Boot Mode field of the Boot Settings screen of
the System Setup program. See "Boot Settings Screen." Once you specify the
boot mode, the system boots in the specified boot mode and you install your
operating system from that mode. Thereafter, you must boot the system to
the same boot mode (BIOS or UEFI) to access the installed operating system.
Trying to boot the operating system from the other boot mode will cause the
system to halt immediately at startup.
®
NOTE: Operating systems must be UEFI-compatible (for example, Microsoft
®
Windows Server 2008 x64 version) to be installed from the UEFI boot mode. DOS
and 32-bit operating systems do not support UEFI and can only be installed from the
BIOS boot mode.
Using the System Setup Program and UEFI Boot Manager
55
Entering the System Setup Program
1
Turn on or restart your system.
2
Press <F2> after you see the following message:
<F2> = System Setup
NOTE: The system will not respond until the USB keyboard is active.
If your operating system begins to load before you press <F2>, allow the
system to finish booting, and then restart your system and try again.
Responding to Error Messages
If an error message appears while the system is booting, make a note of the
message. See "System Messages" for an explanation of the message and
suggestions for correcting errors.
NOTE: After installing a memory upgrade, it is normal for your system to display a
message that the system memory size has changed the first time you start your
system.
Using the System Setup Program Navigation Keys
Keys
Action
Up arrow or <Shift><Tab>
Down arrow or <Tab>
Moves to the previous field.
Moves to the next field.
Spacebar, <+>, <–>, left and Cycles through the settings in a field. In many
right arrows
<Esc>
fields, you can also type the appropriate value.
Exits the System Setup program and restarts the
system if any changes were made.
<F1>
Displays the System Setup program's help file.
NOTE: For most of the options, any changes that you make are recorded but do not
take effect until you restart the system.
56
Using the System Setup Program and UEFI Boot Manager
System Setup Options
Main Screen
Figure 2-1. Main System Setup Program Screen
NOTE: The options for the System Setup program change based on the system
configuration.
in the following sections, where applicable.
Option
Description
System Time
System Date
Memory Settings
Sets the time on the system's internal clock.
Sets the date on the system's internal calendar.
Displays information related to installed memory. See
"Memory Settings Screen."
Processor Settings
Displays information related to processors (speed,
cache size, and so on). See "Processor Settings Screen."
Using the System Setup Program and UEFI Boot Manager
57
Option
Description
SATA Settings
Displays a screen to enable or disable the integrated
SATA controller and ports. See "SATA Settings Screen."
Boot Settings
Displays a screen to specify the boot mode (BIOS or
boot devices. See "Boot Settings Screen."
Integrated Devices
Displays a screen to enable or disable integrated device
and options. See "Integrated Devices Screen."
PCI IRQ Assignment
Displays a screen to change the IRQ assigned to each of
expansion card that requires an IRQ. See "PCI IRQ
Assignments Screen."
Serial Communication
Displays a screen to enable or disable the serial ports
and specify related features and options. See "Serial
Communication Screen."
Embedded Server
Management
Displays a screen to configure the front panel LCD
"Embedded Server Management Screen."
Power Management
Enables you to manage power usage of the processor(s),
fans, and memory modules with preconfigured or
customized settings. See "Power Management Screen."
System Security
Displays a screen to configure the system password and
setup password features. See "System Security Screen,"
Using the System Password," and "Using the Setup
Password" for more information.
Keyboard NumLock
Determines whether your system starts up with the
NumLock mode activated on 101- or 102-key keyboards
(does not apply to 84-key keyboards).
(On default)
Report Keyboard Errors
Report default)
Enables or disables reporting of keyboard errors during
the POST. Select Report for host systems that have
keyboards attached. Select Do Not Report to suppress
all error messages relating to the keyboard or keyboard
controller during POST. This setting does not affect the
operation of the keyboard itself if a keyboard is attached
to the system.
(
58
Using the System Setup Program and UEFI Boot Manager
Option
Description
F1/F2 Prompt on Error
Enables the system to halt on errors during POST,
which allows the user to observe events that may scroll
by unnoticed during normal POST. The user can press
<F1> to continue or <F2> to enter the System Setup
program.
(Enabled default)
CAUTION: When setting this option to Disabled,
the system will not halt if an error occurs during
POST. Any critical errors will be displayed and
logged in the system event log.
Memory Settings Screen
Option
Description
System Memory Size
System Memory Type
System Memory Speed
Video Memory
Displays the amount of system memory.
Displays the type of system memory.
Displays the system memory speed.
Displays the amount of video memory.
System Memory Testing
Specifies whether system memory tests are run at system
(Enabled default)
boot. Options are Enabled and Disabled.
Memory Operating Mode This field displays the type of memory operation if a
valid memory configuration is installed. When set to
Optimizer Mode, the memory controllers run
independently of each other for improved memory
performance. When set to Mirror Mode, memory
mirroring is enabled. When set to Advanced ECC
Mode, two controllers are joined in 128-bit mode
running multi-bit advanced ECC. For information about
the memory modes, see "System Memory."
Node Interleaving
(Disabled default)
If this field is Enabled, memory interleaving is supported
if a symmetric memory configuration is installed. If
Disabled, the system supports Non-Uniform Memory
architecture (NUMA) (asymmetric) memory
configurations.
Using the System Setup Program and UEFI Boot Manager
59
Processor Settings Screen
Option
Description
64-bit
Specifies if the processor(s) support 64-bit extensions.
Displays the processor clock speed.
Core Speed
Bus Speed
Displays the processor bus speed.
Logical Processor
On processors that support Simultaneous
Multi-Threading (SMT) technology, each processor core
supports up to two logical processors. If this field is set to
Enabled, the BIOS reports both logical processors. If set
Disabled, only one logical processor is monitored by
the BIOS.
(Enabled default)
Virtualization Technology Enabled permits virtualization software to use the
(Disabled default)
virtualization technology incorporated in the processor.
NOTE: Disable this feature if your system will not be
running virtualization software.
Execute Disable
Enables or disables Execute Disable Memory Protection
(Enabled default)
Technology.
Number of Cores per
Processor
If set to All, the maximum number of cores in each
processor is enabled.
(All default)
Turbo Mode
If Turbo Boost Technology is supported by the
processor(s), enables or disables Turbo Mode.
C States
When set to Enabled, the processor(s) can operate in all
(Enabled default)
available power states.
Processor X ID
Displays the family, model, Level 2 cache size, Level 3
cache size, and number of cores of each processor.
SATA Settings Screen
Option
Description
Embedded SATA
ATA Mode enables the integrated SATA controller. Off
(ATA Mode default)
disables the controller.
Port A
Auto enables BIOS support for the device attached to
(Auto default)
SATA port A. Off disables BIOS support for the device.
60
Using the System Setup Program and UEFI Boot Manager
Option
Description
Port B
Auto enables BIOS support for the device attached to
(Off default)
SATA port B. Off disables BIOS support for the device.
Boot Settings Screen
Option
Description
Boot Mode
CAUTION: Switching the boot mode could prevent
the system from booting if the operating system was
not installed in the same boot mode.
(BIOS default)
If the system operating system supports Unified
Extensible Firmware Interface, you can set this option to
UEFI. Setting this field to BIOS allows compatibility
with non-UEFI operating systems.
NOTE: Setting this field to UEFI disables the Boot
Sequence, Hard-Disk Drive Sequence, and USB Flash Drive
Emulation Type fields.
Boot Sequence
If Boot Mode is set to BIOS, this field tells the system
where the operating system files needed for startup are
located. If Boot Mode is set to UEFI, you can access the
UEFI boot manager utility by rebooting the system and
pressing <F11> when prompted to do so.
Hard-Disk Drive
Sequence
Determines the order in which the BIOS will attempt to
boot from hard drives in the system during system
startup.
USB Flash Drive
Emulation Type
(Auto default)
Determines the emulation type for a USB flash drive.
Hard disk allows the USB flash drive to act as a hard
drive. Floppy allows the USB flash drive to act as a
removable diskette drive. Auto automatically chooses an
emulation type.
Auto automatically chooses the appropriate emulation
type for the device, except for devices installed in the
internal SD card slot. A device installed in the internal
SD card slot will automatically emulate a hard drive. If
you install a device in this slot that is configured as a
removable diskette drive, you must manually set the
emulation type to Floppy.
Using the System Setup Program and UEFI Boot Manager
61
Option
Description
Boot Sequence Retry
If this field is enabled and the system has failed to boot,
the system will reattempt to boot after 30 seconds.
(Disabled default)
Integrated Devices Screen
Option
Description
Enables or disables the integrated storage controller.
Integrated SAS/RAID
Controller
(Enabled default)
User Accessible USB Ports Enables or disables the user-accessible USB ports.
(All Ports On default)
Options are All Ports On, Only Back Ports On, and All
Ports Off.
Internal USB Port
Enables or disables the internal USB port.
Enables or disables the internal SD card port.
(On default)
Internal SD Card Port
Embedded NIC1 and
NIC2
Enables or disables the OS interface of the four
embedded NICs. (The NICs may also be accessed
through the system’s management controller.)
Embedded NIC3 and
NIC4
Embedded Gb NICx Enables or disables the embedded NICs. Options are
(NIC1 default: Enabled Enabled, Enabled with PXE, Enabled with iSCSI Boot,
with PXE;
and Disabled. PXE support allows the system to boot
Other NICs: Enabled)
from the network.
MAC Address
Displays the MAC address for the NIC.
Capability Detected
Displays the features of the NIC hardware key, if
installed.
NOTE: Some NIC features may require the installation of an
additional driver.
62
Using the System Setup Program and UEFI Boot Manager
Option
Description
OS Watchdog Timer
Sets a timer to monitor the operating system for activity,
and aids in recovery if the system stops responding.
When Enabled, the operating system is allowed to
initialize the timer. When Disabled, the timer is not
initialized.
(Disabled default)
NOTE: This feature is usable only with operating systems
that support WDAT implementations of the Advanced
Configuration and Power Interface (ACPI) 3.0b
specification.
I/OAT DMA Engine
Enables or disables the I/O Acceleration Technology
feature.
(Disabled default)
Embedded Video
Controller
Enables or disables BIOS support for the integrated video
controller.
(Enabled default)
NOTE: This field can be disabled only if an add-in video
card is present. If this field is disabled, remote access
features such as virtual KVM are not available.
PCI IRQ Assignments Screen
Option
Description
<PCIe device>
Use the <+> and <-> keys to manually select an IRQ
for a given device, or select Default to allow the BIOS to
select an IRQ value at system startup.
Serial Communication Screen
Option
Description
Serial Communication
(On without Console
Redirection default)
Selects whether the serial communication devices
(Serial Device 1 and Serial Device 2) are enabled in
BIOS. BIOS console redirection can also be enabled and
the port address used can be specified.
Options are On without Console Redirection, On with
Console Redirection via COM1, On with Console
Redirection via COM2, and Off.
Using the System Setup Program and UEFI Boot Manager
63
Option
Description
Serial Port Address
(Serial Device 1=COM1,
Serial Device2=COM2
default)
Sets the serial port addresses for the two serial devices.
NOTE: Only Serial Device 2 can be used for Serial Over
LAN (SOL). To use console redirection by SOL, configure
the same port address for console redirection and the
serial device.
External Serial Connector Specifies whether Serial Device 1, Serial Device 2, or
Remote Access Device has access to the external serial
connector.
NOTE: Only Serial Device 2 can be used for Serial Over
LAN (SOL). To use console redirection by SOL, configure
the same port address for console redirection and the
serial device.
Failsafe Baud Rate
Displays the failsafe baud rate used for console
redirection. BIOS attempts to determine the baud rate
automatically. This failsafe baud rate is used only if the
attempt fails. This rate should not be adjusted.
(115200 default)
Remote Terminal Type
Sets the remote console terminal type, either
(VT 100/VT220 default)
VT100/VT220 or ANSI.
Redirection After Boot
Enables or disables BIOS console redirection when the
operating system is loaded.
(Enabled default)
Embedded Server Management Screen
Option
Description
Front Panel LCD Options Options are User Defined String, Model Number, or
None.
If the LCD Home screen is set to an option other than
these three choices, the option will be displayed as
"Advanced" in the BIOS. In this event, the option cannot
be changed in the BIOS unless it is changed back to User
Defined String, Model Number, or None through
another LCD configuration utility (such as the iDRAC
Configuration Utility or the LCD panel menu).
User-Defined LCD String You can enter a name or other identifier for the system, to
be displayed on the LCD module screen.
64
Using the System Setup Program and UEFI Boot Manager
Power Management Screen
Option
Description
Power Management
Options are OS Control, Active Power Controller,
Custom, or Maximum Performance. For all but the
Custom setting, the BIOS pre-configures the power
settings on this screen as follows:
•
OS Control sets the CPU power to OS DBPM, the fan
power to Minimum Power, and the memory power to
Maximum Performance. In this setting, all processor
performance information is passed from the system
BIOS to the operating system for control. The operating
system sets the processor performance based on
processor utilization.
•
Active Power Controller sets the CPU power to System
DBPM, the fan power to Minimum Power, and the
memory power to Maximum Performance. The BIOS
sets the processor performance based on processor
utilization.
•
Maximum Performance sets all fields to Maximum
Performance
.
If you select Custom, you can configure each option
independently.
CPU Power and
Performance
Options are OS DBPM, System DBPM, Maximum
Performance, or Minimum Power.
Management
Fan Power and
Performance
Management
Options are Maximum Performance or Minimum Power.
Memory Power and
Performance
Options are Maximum Performance, a specified
frequency, or Minimum Power.
Management
Using the System Setup Program and UEFI Boot Manager
65
System Security Screen
Option
Description
System Password
Displays the current status of the password security
feature and allows a new system password assignment and
verification.
NOTE: See "Using the System Password" for more
information.
Setup Password
Restricts access to the System Setup program by using a
setup password.
NOTE: See "Using the System Password" for more
information.
Password Status
When Setup Password is assigned and this field is
Locked, the system password cannot be changed or
disabled at system start-up.
(Unlocked default)
See "Using the System Password" for more information.
TPM Security
Sets the reporting of the Trusted Platform Module
(TPM) in the system.
(Off default)
If Off, the presence of the TPM is not reported to the
operating system.
If On with Pre-boot Measurements, the system reports
the TPM to the operating system and stores the pre-boot
measurements to the TPM during POST.
If On without Pre-boot Measurements, the system
reports the TPM to the operating system and bypasses
pre-boot measurements.
TPM Activation
When set to Activate, the TPM is enabled to default
settings. When set to Deactivate, the TPM is disabled.
The No Change state initiates no action. The operational
state of the TPM remains unchanged (all user settings for
the TPM are preserved).
(No Change default)
NOTE: This field is read-only when TPM Security is set to
Off.
66
Using the System Setup Program and UEFI Boot Manager
Option
Description
CAUTION: Clearing the TPM will lose all encryption
TPM Clear
(No default)
keys in the TPM. This option prevents booting to the
operating system and results in data loss if the
encryption keys cannot be restored. Back up the TPM
keys prior to enabling this option.
When set to Yes, all TPM contents are cleared.
NOTE: This field is read-only when TPM Security is set to
Off.
Power Button
If Enabled, the power button can turn the system's power
off and on. On an ACPI-compliant operating system, the
system performs an orderly shutdown before power is
turned off.
(Enabled default)
When Disabled, the button can only turn on system
power.
NMI Button
CAUTION: Use the NMI button only if directed to do
so by qualified support personnel or by the operating
system's documentation. Pressing this button halts
the operating system and displays a diagnostic
screen.
(Disabled default)
Enables or disables the NMI feature.
AC Power Recovery
Determines how the system reacts when power is
restored. If set to Last, the system returns to the last
power state. On turns on the system after power is
restored. Off allows the system to remain off after power
is restored.
(Last default)
AC Power Recovery Delay Determines when the system restarts after power is
restored. Options are Immediate, Random (a random
value of 30 to 240 seconds), or a user-defined value of 30
to 240 seconds.
Exit Screen
Press <Esc> to exit the System Setup program; the Exit screen displays:
• Save Changes and Exit
• Discard Changes and Exit
• Return to Setup
Using the System Setup Program and UEFI Boot Manager
67
Entering the UEFI Boot Manager
®
NOTE: Operating systems must be 64-bit UEFI-compatible (for example, Microsoft
®
Windows Server 2008 x64 version) to be installed from the UEFI boot mode. DOS
and 32-bit operating systems can only be installed from the BIOS boot mode.
NOTE: The Boot Mode must be set to UEFI in the System Setup program to access
the UEFI Boot Manager.
The UEFI Boot Manager enables you to:
•
•
Add, delete, and arrange boot options
Access the System Setup program and BIOS-level boot options without
rebooting
1
Turn on or restart your system.
2
Press <F11> after you see the following message:
<F11> = UEFI Boot Manager
NOTE: The system will not respond until the USB keyboard is active.
If your operating system begins to load before you press <F11>, allow the
system to finish booting, and then restart your system and try again.
Using the UEFI Boot Manager Navigation Keys
Keys
Action
Up arrow
Down arrow
Moves to and highlights the previous field.
Moves to and highlights the next field.
Cycles through the settings in a field.
Spacebar, <Enter>, <+>,
<–>,
<Esc>
Refreshes the UEFI Boot Manager screen, or
returns to the UEFI Boot Manager screen from the
other program screens.
<F1>
Displays the UEFI Boot Manager help file.
68
Using the System Setup Program and UEFI Boot Manager
UEFI Boot Manager Screen
Option
Description
Continue
The system attempts to boot to devices starting with
the first item in the boot order. If the boot attempt fails,
the system will continue with the next item in the boot
order until the boot is successful or no more boot
options are found.
<Boot options>
Displays the list of available boot options (marked with
asterisks). Select the boot option you wish to use and
press Enter.
NOTE: If you hot-add a boot device, press <ESC> to
refresh the list of boot options.
UEFI Boot Settings
Enables you to add, delete, enable, or disable boot
options; change boot order; or execute a one-time boot
option.
System Utilities
Enables you to access the System Setup program,
System Services, and BIOS-level boot options.
UEFI Boot Settings Screen
Option
Description
Add Boot Option
Delete Boot Option
Adds a new boot option.
Deletes an existing boot option.
Enable/Disable Boot
Option
Disables and enables a boot option in the boot option
list.
Change Boot Order
Changes the order of the boot option list.
One-Time Boot From File Sets a one-time boot option not included in the boot
option list.
System Utilities Screen
Option
Description
System Setup
Accesses the System Setup program without rebooting.
Using the System Setup Program and UEFI Boot Manager
69
Option
Description
System Services
Restarts the system and accesses the Unified Server
Configurator, which enables you to run utilities such as
system diagnostics.
BIOS Boot Manager
Accesses the BIOS-level boot options list without
switch to BIOS boot mode if you need to boot to a
device with a non-UEFI operating system, such as a
bootable DOS media with diagnostics software.
Reboot System
Restarts the system.
System and Setup Password Features
NOTE: For a forgotten password, see "Disabling a Forgotten Password."
Your system is shipped without the system password feature enabled in BIOS.
CAUTION: Anyone can access the data stored on your system if the system is
running and unattended.
Using the System Password
When a system password is assigned, the system prompts for the system
password after the system starts and only those with the password have full
use of the system.
Assigning a System Password
Before assigning a system password, enter the System Setup program and
check the System Password option.
When a system password is assigned, System Password is Enabled. If
Password Status is Unlocked, you can change the system password. If Locked,
you cannot change the system password. Disabling the password jumper on
the system board sets System Password to Disabled, and you cannot change
or enter a new system password.
When a system password is not assigned and the password jumper on the
system board is in the enabled position, System Password is Not Enabled and
Password Status is Unlocked. To assign a system password:
1
Verify that Password Status is Unlocked.
70
Using the System Setup Program and UEFI Boot Manager
2
3
Highlight the System Password option and press <Enter>.
Type your new system password.
You can use up to 32 characters in your password.
As you type, placeholders appear in the field.
The password assignment is not case-sensitive. To erase a character, press
<Backspace> or the left-arrow key.
NOTE: To escape from the field without assigning a system password, press
<Enter> to move to another field, or press <Esc> prior to completing step 5.
4
5
Press <Enter>.
To confirm your password, type it a second time and press <Enter>.
begin using your system.
6
Either reboot the system now for the password protection to take effect or
continue working.
NOTE: Password protection does not take effect until the system reboots.
Using Your System Password to Secure Your System
NOTE: If you have assigned a setup password (see "Using the Setup Password"),
the system accepts your setup password as an alternate system password.
When Password Status is Unlocked, you have the option to leave the
password security enabled or to disable password security.
To leave the password security enabled:
1
2
Turn on or reboot your system by pressing <Ctrl><Alt><Del>.
Type your password and press <Enter>.
To disable the password security:
1
2
Turn on or reboot your system by pressing <Ctrl><Alt><Del>.
Type your password and press <Ctrl><Enter>.
When Password Status is Locked, you must type the password and press
<Enter> when prompted at reboot.
Using the System Setup Program and UEFI Boot Manager
71
If an incorrect system password is entered, the system displays a message and
prompts you to re-enter your password. You have three attempts to enter the
correct password. After the third unsuccessful attempt, the system displays an
error message that the system has halted and must be shut down manually
with the power button. Even after you shut down and restart the system, the
error message continues to be displayed until the correct password is entered.
NOTE: You can use the Password Status option in conjunction with the System
Password and Setup Password options to protect your system from unauthorized
changes.
Changing an Existing System Password
1
2
3
4
Enter the System Setup program by pressing <F2> during POST.
Select the System Security screen.
Verify that the Password Status is Unlocked
.
Type the new system password in the two password fields.
The System Password field changes to Not Enabled if the password was
deleted.
Disabling the System Password
If the system password is already set, you can disable it by typing the password
during POST and pressing <Ctrl><Enter>, or you can enter the System
Setup program and press <Enter> twice in the system password menu.
Using the Setup Password
Assigning a Setup Password
You can assign a setup password only when the Setup Password is Not
Enabled. To assign a setup password, highlight the Setup Password option
and press the <+> or <–> key. The system prompts you to enter and verify
the password.
NOTE: The setup password can be the same as the system password. If the two
passwords are different, the setup password can be used as an alternate system
password. The system password cannot be used in place of the setup password.
You can use up to 32 characters in your password.
As you type, placeholders appear in the field.
72
Using the System Setup Program and UEFI Boot Manager
The password assignment is not case-sensitive. To erase a character, press
<Backspace> or the left-arrow key.
When you verify the password, the Setup Password changes to Enabled. The
next time you enter the System Setup program, the system prompts you for
the setup password.
A change to the Setup Password option becomes effective immediately
(restarting the system is not required).
Operating With a Setup Password Enabled
If Setup Password is Enabled, you must enter the correct setup password
before modifying most of the System Setup options.
If you do not enter the correct password in three attempts, the system lets you
view, but not modify, the System Setup screens. The following options are
exceptions: If System Password is not Enabled and is not locked through the
Password Status option, you can assign a system password. You cannot disable
or change an existing system password.
NOTE: You can use the Password Status option in conjunction with the Setup
Password option to protect the system password from unauthorized changes.
Deleting or Changing an Existing Setup Password
1
2
Enter the System Setup program and select the System Security
.
Highlight Setup Password, press <Enter> to access the setup password
window. Press <Enter> twice to clear the existing setup password.
The setting changes to Not Enabled
.
3
If you want to assign a new setup password, perform the steps in "Assigning
a Setup Password."
iDRAC Configuration Utility
The iDRAC Configuration Utility is a pre-boot configuration environment
that allows you to view and set parameters for the iDRAC6 and for the
managed server. The iDRAC Configuration Utility enables you to:
•
Configure, enable, or disable the iDRAC6 local area network through the
dedicated iDRAC6 Enterprise card port or the embedded NICs.
•
Enable or disable IPMI over LAN.
Using the System Setup Program and UEFI Boot Manager
73
•
•
•
Enable a LAN Platform Event Trap (PET) destination.
Attach or detach the Virtual Media devices.
Change the administrative username and password and manage user
privileges.
•
View System Event Log (SEL) messages or clear messages from the log.
For additional information on using iDRAC6, see the documentation for
iDRAC6 and systems management applications.
Entering the iDRAC Configuration Utility
1
2
Turn on or restart your system.
Press <Ctrl><E> when prompted during POST.
If your operating system begins to load before you press <Crtl><E>,
allow the system to finish booting, and then restart your system and try
again.
74
Using the System Setup Program and UEFI Boot Manager
Installing System Components
Recommended Tools
•
•
•
•
Key to the system keylock
#1 and #2 Phillips screwdrivers
Wrist grounding strap
T8, T10, and T15 Torx drivers
Inside the System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Installing System Components
75
Figure 3-1. Inside the System
7
8
9
6
5
4
10
3
2
1
11
12
18
17
16
13
15
14
2
1
USB connector for optional internal
USB key
Internal SD Module
3
5
RAID battery (optional)
4
6
hot-swappable cooling fans (4 or 5)
processors (1 or 2)
memory modules (up to 18 total, 9 for
each processor)
7
9
power supply bays (2)
8
riser 2 (PCIe slots 3 and 4)
riser 1 (PCIe slots 1 and 2)
10 iDRAC6 Enterprise card (optional)
12 integrated storage controller card
14 slimline optical drive
11 RAID battery connector (optional)
13 SAS backplane
15 SAS or SATA hard drives
17 control panel
16 LCD display module
18 information tag
76
Installing System Components
Front Bezel (Optional)
A lock on the bezel restricts access to the power button, optical drive, and
hard drive(s). The LCD panel and navigation buttons are accessible through
the front bezel. See Figure 3-2.
Removing the Front Bezel
1
2
3
Using the system key, unlock the bezel.
Pull up on the release latch next to the key lock.
Rotate the left end of the bezel away from the system to release the right
end of the bezel.
4
Pull the bezel away from the system. See Figure 3-2.
Figure 3-2. Removing the Front Bezel
2
1
4
3
1
3
release latch
hinge tabs
2
4
bezel
key lock
Installing System Components
77
Installing the Front Bezel
1
Insert the hinge tab on the right of the bezel into the slot on the right side
of the system front panel.
2
3
Rotate the left side of the bezel toward the system.
Press the bezel to the system to engage the latch.
Opening and Closing the System
WARNING: Whenever you need to lift the system, get others to assist you. To
avoid injury, do not attempt to lift the system by yourself.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Opening the System
1
Unless you are installing a hot-swappable component such as a cooling fan
or power supply, turn off the system and attached peripherals, and
disconnect the system from the electrical outlet and peripherals.
2
3
4
Rotate the latch release lock counter-clockwise to the unlocked position.
See Figure 3-3.
Lift up on the latch on top of the system and slide the cover back. See
Figure 3-3.
Grasp the cover on both sides and lift the cover away from the system.
Closing the System
1
2
Lift up the latch on the cover.
Place the cover onto the chassis and offset the cover slightly back so that it
clears the chassis hooks and lays flush on the system chassis. See
Figure 3-3.
3
4
Push down the latch to lever the cover into the closed position.
Rotate the latch release lock in a clockwise direction to secure the cover.
78
Installing System Components
Figure 3-3. Removing or Installing the Cover
1
2
3
1
3
latch
2
latch release lock
chassis hooks
Information Tag
Removing the Information Tag
1
2
3
Pull the information tag out of its slot in the chassis, until it is in the lock
position.
To release the top portion of the tag, pull down on the tag until it
disengages from the slot in the chassis.
To release the lower portion of the tag, pull up on the tag until it
disengages from the slot in the chassis.
Installing System Components
79
Figure 3-4. Removing the Information Tag
1
1
information tag
Installing the Information Tag
1
2
Align the information tag with the slot on the chassis.
Slide the information tag into the chassis, until it locks into place
Hard Drives
Your system supports up to six 3.5-inch hot-swappable SAS and SATA hard
drives.
The hard drives are installed at the front of the system and connect to the
system board through the SAS backplane. Hard drives are supplied in special
hot-swappable hard-drive carriers that fit in the hard-drive bays.
CAUTION: Before attempting to remove or install a drive while the system is
running, see the documentation for the storage controller card to ensure that the
host adapter is configured correctly to support hot-swap drive removal and
insertion.
80
Installing System Components
CAUTION: Do not turn off or reboot your system while the drive is being formatted.
Doing so can cause a drive failure.
NOTE: Use only drives that have been tested and approved for use with the SAS
backplane board.
When you format a hard drive, allow enough time for the formatting to be
completed. Be aware that high-capacity hard drives can take a number of
hours to format.
Removing a Hard-Drive Blank
CAUTION: To maintain proper system cooling, you must install drive blanks in all
empty hard-drive bays.
1
2
Remove the front bezel. See "Removing the Front Bezel."
Grasp the front of the hard-drive blank, press the release lever on the
right side, and slide the blank out until it is free of the drive bay. See
Figure 3-5
.
Figure 3-5. Removing and Installing the Hard Drive Blank
1
2
1
3.5-in hard drive blank
2
release latch
Installing a Hard-Drive Blank
Align the hard-drive blank with the drive bay and insert the blank into the
drive bay until the release lever clicks into place.
Installing System Components
81
Removing a Hot-Swap Hard Drive
CAUTION: Ensure that your operating system supports hot-swap drive removal
and installation. See the documentation provided with your operating system for
more information.
1
2
If present, remove the front bezel. See "Removing the Front Bezel."
From the RAID management software, prepare the drive for removal. Wait
until the hard-drive indicators on the drive carrier signal that the drive
can be removed safely. See your SAS RAID controller documentation for
information about hot-swap drive removal.
If the drive has been online, the green activity/fault indicator will flash as
the drive is powered down. When the drive indicators are off, the drive is
ready for removal.
3
4
Press the button on the front of the drive carrier and open the drive
carrier release handle to release the drive. See Figure 3-6
.
Slide the hard drive out until it is free of the drive bay.
CAUTION: To maintain proper system cooling, all empty hard-drive bays must
have drive blanks installed.
5
6
Insert a drive blank in the vacated drive bay. See "Installing a Hard-Drive
Blank."
If applicable, install the bezel. See "Installing the Front Bezel."
Installing a Hot-Swap Hard Drive
CAUTION: When installing a hard drive, ensure that the adjacent drives are fully
installed. Inserting a hard-drive carrier and attempting to lock its handle next to a
partially installed carrier can damage the partially installed carrier's shield spring
and make it unusable.
CAUTION: To prevent data loss, ensure that your operating system supports
hot-swap drive installation. See the documentation supplied with your operating
system.
1
2
If present, remove the front bezel. See "Removing the Front Bezel."
If a drive blank is present in the bay, remove it. See "Removing a Hard-
Drive Blank."
82
Installing System Components
Figure 3-6. Installing the Hot-Swap Hard Drive
1
2
1
release button
2
hard drive carrier handle
3
Install the hot-swap hard drive.
a
b
Press the button on the front of the drive carrier and open the handle.
Insert the hard-drive carrier into the drive bay until the carrier
contacts the backplane.
c
Close the handle to lock the drive in place.
4
If applicable, install the bezel. See "Installing the Front Bezel."
Removing a Hard Drive From a Hard-Drive Carrier
Remove the screws from the slide rails on the hard-drive carrier and separate
the hard drive from the carrier. See Figure 3-7
.
Installing a Hard Drive Into a Hard-Drive Carrier
1
Insert the hard drive into the hard-drive carrier with the connector end
of the drive at the back. See Figure 3-7
.
2
Align the screw holes on the hard drive with the back set of holes on the
hard drive carrier.
When aligned correctly, the back of the hard drive will be flush with the
back of the hard-drive carrier.
Installing System Components
83
Power Supplies
Your system supports the following power supply modules:
•
•
570-W Energy Smart power supply
870-W High Output power supply
NOTE: The system does not support a mixed installation of High Output and Energy
Smart power supplies.
If only one power supply is installed, it must be installed in the PS1 power
supply bay.
CAUTION: To ensure proper system cooling, the power supply blank must be
installed in the PS2 bay in a non-redundant configuration. See "Installing the
Power Supply Blank."
Removing a Power Supply
CAUTION: If troubleshooting a power supply mismatch error, replace only the
power supply with the flashing indicator. Swapping the opposite power supply to
make a matched pair can result in an error condition and unexpected system
shutdown. To change from a High Output configuration to an Energy Smart
NOTE: You may have to unlatch and lift the optional cable management arm if it
interferes with power supply removal. For information about the cable management
arm, see the system’s rack documentation.
1
2
Disconnect the power cable from the power source and the power supply
you intend to remove and remove the cables from the Velcro strap.
Press the lever release latch and slide the power supply out of the chassis.
See Figure 3-8.
Installing System Components
85
Figure 3-8. Removing and Installing the Power Supply
1
2
3
1
3
power supply handle
release latch
2
Velcro strap
Replacing a Power Supply
1
On a system with redundant power supplies, verify that both power
supplies are the same type and have the same maximum output power.
NOTE: The maximum output power (shown in watts) is listed on the power
supply label.
2
Slide the new power supply into the chassis until the power supply is fully
seated and the release latch snaps into place. See Figure 3-8.
NOTE: If you unlatched the cable management arm in step 2 of the previous
procedure, relatch it. For information about the cable management arm, see
the system’s rack documentation.
3
Connect the power cable to the power supply and plug the cable into a
power outlet.
CAUTION: When connecting the power cable, secure the cable with the Velcro
strap.
86
Installing System Components
NOTE: When installing, hot-swapping, or hot-adding a new power supply, allow
several seconds for the system to recognize the power supply and determine its
status. The power-supply status indicator turns green to signify that the power
supply is functioning properly (see Figure 1-5).
Removing the Power Supply Blank
If you are installing a second power supply, remove the power supply blank in
the bay by pulling outward on the blank.
CAUTION: To ensure proper system cooling, the power supply blank must be
installed in the second power supply bay in a non-redundant configuration.
Remove the power supply blank only if you are installing a second power supply.
Installing the Power Supply Blank
NOTE: Install the power supply blank only in the second power supply bay.
To install the power supply blank, align the blank with the power supply bay
and insert it into the chassis until it clicks into place.
Internal SD Module
Installing the Internal SD Module
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Position the module so the tabs on the underside of the tray fit into the
hooks on the chassis, then lower the opposite edge of the card into place.
See Figure 3-9.
Installing System Components
87
Figure 3-9. Removing or Installing the Internal SD Module
3
4
2
5
1
6
8
7
1
3
5
7
latch
2
4
6
8
SD flash card
SD card slot (SD connector)
internal SD module cable
control panel board
release tab
internal SD module connector
4
Connect the internal SD module cable to the connector on the control
panel board. See Figure 3-9.
5
6
Close the system. See "Closing the System."
Reconnect the system and peripherals to their power sources, and turn
them on.
88
Installing System Components
Removing the Internal SD Module
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
by your warranty. Read and follow the safety instructions that came with the
product.
1
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Disconnect the cable from the internal SD module and from the control
panel board. See Figure 3-9.
4
Lift upwards on the latch securing the internal SD module to the chassis,
then lift the tray out of the chassis. See Figure 3-9.
5
6
Close the system. See "Closing the System."
Reconnect the system and peripherals to their power sources, and turn
them on.
Internal SD Flash Card
Installing the Internal SD Flash Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: To use an SD card with your system, ensure that the internal SD card port is
enabled in the System Setup program. See "Using the System Setup Program and
UEFI Boot Manager."
1
2
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
Open the system. See "Opening the System."
Installing System Components
89
3
Locate the SD card connector on the internal SD module and, with the
label side facing up, insert the contact-pin end of the card into the slot.
See Figure 3-9.
NOTE: The slot is keyed to ensure correct insertion of the card.
Press the card into the card slot to lock it into place.
Close the system. See "Closing the System."
4
5
6
Reconnect the system to power and restart the system.
Removing the Internal SD Flash Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Locate the SD card slot on the internal SD module and press inward on
the card to release it from the slot and remove the card.
4
5
Close the system. See "Closing the System."
Reconnect the system to power and restart the system.
Internal USB Memory Key
An optional USB memory key installed inside your system can be used as a
boot device, security key, or mass storage device. The USB connector must be
enabled by the Internal USB Port option in the Integrated Devices screen of
the System Setup program. See "Using the System Setup Program and UEFI
Boot Manager."
To boot from the USB memory key, configure the USB memory key with a
boot image and then specify the USB memory key in the boot sequence in the
System Setup program.
90
Installing System Components
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: Maximum dimensions supported for the USB memory key are 24-mm (.94-in)
wide, 79-mm (3.11-in) long, and 8.6-mm (.33-in) tall.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
Open the system. See "Opening the System".
Locate the USB connector on the control panel. See Figure 3-10.
Insert the USB memory key into the USB connector. See Figure 3-10.
Figure 3-10. Removing or Installing the USB Memory Key
3
1
2
1
3
control panel board
USB memory key
2
USB memory key connector
5
Close the system. See "Closing the System."
6
Reconnect the system to power and restart the system.
Installing System Components
91
Internal USB Cable
Removing the Internal USB Cable
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
Open the system. See "Opening the System".
Remove the fan bracket. See "Removing the Fan Bracket".
Remove the USB cable from the appropriate connector on the Control
Panel.
5
6
Remove the USB cable from the cable routing guides on the inside of the
chassis. If applicable, remove any other cables from the cable routing
guides.
Remove the USB cable from the connector on the system board.
Installing the Internal USB Cable
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
5
Open the system. See "Opening the System".
Remove the fan bracket. See "Removing the Fan Bracket".
Connect the USB cable to the appropriate connector on the control panel.
Route the cable through the cable routing guides on the inside of the
chassis.
6
7
8
9
Connect the USB cable to the connector on the system board.
Replace the fan bracket. See "Replacing the Fan Bracket".
Close the system. See "Closing the System".
Reconnect the system to the electrical outlet, including any attached
peripherals, and turn the system on.
92
Installing System Components
iDRAC6 Enterprise Card (Optional)
The optional Integrated Dell™ Remote Access Controller 6 (iDRAC6)
Enterprise card provides a set of advanced features for managing the server
remotely.
Installing an iDRAC6 Enterprise Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Remove the plastic filler plug for the iDRAC6 Enterprise port from the
system back panel. See "Back Panel Features and Indicators" for the port
location.
4
5
If installed, remove all expansion cards from expansion-card riser 1. See
"Removing an Expansion Card."
Install the iDRAC6 Enterprise card:
a
b
Angle the card so that the RJ-45 connector fits through the back-panel
opening. See Figure 3-11.
standoffs next to the iDRAC6 connector on the system board. See
Figure 6-2 for the location of the connector.
c
Press the card down until it is fully seated. See Figure 3-11.
When the front of the card is fully seated, the plastic standoffs snap
over the edge of the card.
6
Reinstall all expansion cards in expansion-card riser 1. See "Installing an
Expansion Card."
7
8
Close the system. See "Closing the System."
Reconnect the system and peripherals to their power sources, and turn
them on.
Installing System Components
93
Figure 3-11. Removing and Installing the iDRAC6 Enterprise Card
2
1
3
5
4
1
3
5
iDRAC6 Enterprise card
VFlash SD card
2
4
VFlash media slot
retention standoff posts (2)
iDRAC6 Enterprise card connector
Removing an iDRAC6 Enterprise Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
If installed, remove all expansion cards from expansion-card riser 1. See
"Removing an Expansion Card."
4
5
Remove the VFlash media card (if installed) from the iDRAC6 Enterprise
card. See "VFlash Media (Optional)."
If present, disconnect the Ethernet cable from the iDRAC6 Enterprise
card.
94
Installing System Components
6
Remove the iDRAC6 Enterprise card:
a
b
c
Pull back slightly on the two tabs at the front edge of the card and
gently lift the front edge of the card off of the retention standoffs.
As the card releases from the standoffs, the connector under the card
disengages from the system board connector.
Slide the card away from the back of the system until the RJ-45
connector is clear of the back panel, then lift the card out of the
system.
7
8
9
Install the plastic filler plug for the vacated RJ-45 Ethernet port in the
system back panel.
Reinstall the expansion card(s) in expansion-card riser 1. See "Installing an
Expansion Card."
10 Reconnect the system and peripherals to their power sources, and turn
them on.
VFlash Media (Optional)
The optional VFlash media is a Secure Digital (SD) card that can be used
with the optional iDRAC6 Enterprise card. See "iDRAC6 Enterprise Card
(Optional)."
1
Locate the VFlash media slot on the back of the system and insert the
contact-pin end of the SD card (with the label side facing up) into the
slot. See "Back Panel Features and Indicators" for the slot location.
NOTE: The slot is keyed to ensure correct insertion of the card.
2
Press inward on the card to lock it into the slot
.
To remove the card, push inward on the card to release it, and pull the card
from the card slot.
NIC Hardware Key
iSCSI and other future functionalities for the system’s embedded NICs are
enabled by installing an optional NIC hardware key in the ISCSI_KEY socket
on the system board.
Installing System Components
95
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NIC hardware key (if installed) with a new hardware key.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
Open the system. See "Opening the System."
Locate the ISCSI_KEY connector on the system board. See Figure 6-2.
Insert the NIC hardware key into the connector onto the board. See
Figure 3-12.
Figure 3-12. Removing or Installing the NIC Hardware Key
1
2
1
NIC hardware key
2
ISCSI_KEY connector
5
Close the system. See "Closing the System."
96
Installing System Components
6
Reconnect the system to the electrical outlet and turn on the system and
attached peripherals.
Cooling Shroud
The system provides a cooling shroud that directs airflow from the cooling
fans over the system processor(s) and memory module(s).
WARNING: The memory modules are hot to the touch for some time after the
system has been powered down. Allow the memory modules to cool before
handling them.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: Never operate your system with the cooling shroud removed.
Overheating of the system can develop quickly resulting in a shutdown of the
system and the loss of data.
Removing the Cooling Shroud
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Use the lift handles on the cooling shroud to lift the shroud out of the
system. See Figure 3-13.
Installing System Components
97
Figure 3-13. Removing and Installing the Cooling Shroud
1
2
3
1
3
lift handles
processors
2
alignment tabs
Installing the Cooling Shroud
1
Align the tabs on the right side of the cooling shroud with the cutouts in
the right chassis wall.
2
Lower the right end of the shroud into the chassis cutouts and rotate the
left end down inside the left chassis wall.
3
4
Close the system. See "Closing the System."
Reconnect the system to the electrical outlet and turn on the system and
attached peripherals.
98
Installing System Components
Cooling Fans
The system has either five or four hot-swappable fans to provide cooling to
the system’s interior components.
•
•
Dual-processor configurations have five fans.
Single-processor configurations have four fans (fans 1 through 4) and a
blank inserted in the fan 5 bay. Fan 5 can be installed as an optional fan.
NOTE: In the event of a problem with a particular fan, the fan’s number is
referenced by the system’s management software, allowing you to easily identify
and replace the proper fan.
Removing a Cooling Fan
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: The cooling fans are hot-swappable. To maintain proper cooling while
the system is on, replace only one fan at a time.
CAUTION: On single-processor systems using four fans, the fan blank must be
installed in the FAN5 bay to maintain proper cooling while the system is on.
NOTE: If a fan is installed in FAN5 in a single-processor configuration, the fan will
still be operational, however the fan will not appear in the iDRAC user interface
unless the fan was installed before the system was started.
1
2
Open the system. See "Opening the System."
WARNING: Use caution when handling the fan until the fan blades stop spinning.
Press the release tab while grasping the ends of the fan and lift the fan
straight up from the fan bracket. See Figure 3-14.
Installing System Components
99
Figure 3-14. Removing and Installing the Cooling Fan
2
1
3
1
3
fan
2
fan release handle
fan bracket
Replacing a Cooling Fan
1
Align the fan plug with the connector at the base of the fan bracket and
lower the fan into the bracket until the fan is fully seated. See Figure 3-14.
2
Close the system. See "Closing the System."
Removing the Fan Bracket
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
100
Installing System Components
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Optional: Remove the fans from the fan bracket. See "Removing a Cooling
Fan."
4
Lift the release latches on each end of the fan bracket and lift the bracket
out of the system. See Figure 3-15.
Figure 3-15. Removing and Installing the Processor Fan Bracket
1
2
4
3
1
3
fan bracket
2
4
release latch
mounting pin
fan connector on system board
Installing System Components
101
Replacing the Fan Bracket
1
Align the fan bracket down onto the bracket base so that the mounting
pins fit correctly into the bracket base. See Figure 3-15.
2
3
Insert the bracket and engage the release levers to lock it in place.
If removed, replace the fans in the fan bracket. See "Replacing a Cooling
Fan."
4
Close the system. See "Closing the System."
Optical Drive
An optional slimline DVD-ROM or DVD+RW optical drive slides into the front
panel and connects to the SATA controller on the system board. The optical
drive is on the right or left side of the system, depending on your chassis.
NOTE: DVD devices are data only.
Removing the Optical Drive
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from its electrical outlet.
2
3
4
Open the system. See "Opening the System."
Disconnect the optical drive cable from the back of the optical drive.
To remove the optical drive, press down on the blue release tab at the back
of the optical drive and push the drive out of the system. See Figure 3-16.
Installing the Optical Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
102
Installing System Components
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from its electrical outlet.
2
3
Open the system. See "Opening the System."
To remove the optical drive blank, press down on the blue release tab at
the back of the blank and push the blank out of the system.
4
5
6
7
Align the optical drive with its opening in the front panel. See Figure 3-16.
Slide in the optical drive until the latch snaps into place.
Connect the optical drive cable to the back of the drive tray.
If not already done, connect the power and interface cables from the
optical drive to the system board connectors.
a
Connect the power cable to the DVD/TBU_PWR connector on the
Installing System Components
103
Figure 3-17. Routing the Optical Drive Cable
4
2
3
1
1
3
optical drive connector
cable retention bracket
2
4
DVD/TBU_PWR connector
SATA_A connector
Integrated Storage Controller Card
Your system includes a dedicated expansion-card slot on riser 1 for an
integrated storage controller card that provides the storage subsystem for your
system’s internal hard drives. The controller supports SAS and SATA hard
drives and also enables you to set up the hard drives in RAID configurations
as supported by the version of the storage controller included with your
system.
Installing System Components
105
Removing the Integrated Storage Controller Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Remove all expansion cards from expansion-card riser 1. See "Removing an
Expansion Card."
4
Disconnect the SAS cable(s) from the storage controller card.
CAUTION: Disconnecting the RAID battery cable from a PERC card can cause
data loss if the "dirty cache" LED on the card is lit. The LED indicates that data is
still cached in controller memory and the data was not cleared at system
shutdown.
5
6
If necessary, disconnect the RAID battery cable from the controller.
Bend both card-edge guides outward and pull the storage controller card
out of the connector. See Figure 3-18.
7
Bend outward on both card-edge guides to release the controller, lift the
side of the controller that is adjacent to the blue guide, and then remove
the controller out toward the rear of the chassis. See Figure 3-18.
Installing the Integrated Storage Controller Card
1
With the storage controller card-edge facing the riser, insert one side of the
card into the black card-edge guide.
2
Bend outward on the blue card-edge guide, lower the card onto the blue
card-edge guide, and release the guide. See Figure 3-18.
106
Installing System Components
6
7
If not already done, route the interface and RAID battery cables in the
cable path inside the right interior wall of the chassis beneath the cable
retention bracket. See "Cable Routing" and Figure 3-21.
Connect the SAS A cable to the SAS A connector on the backplane and, if
applicable, connect the SAS B cable to the SAS B connector on the
backplane.
8
9
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
Figure 3-19. Storage Controller Card Cabling
7
2
5
8
1
4
6
3
1
3
5
7
RAID battery (PERC only)
2
SAS B connector on backplane
cable retention bracket
SAS A connector on backplane
integrated storage controller card
SAS_1 connector
4
6
8
SAS_0 connector
RAID battery connector (PERC only)
108
Installing System Components
RAID Battery
The information in this section applies only to systems with the optional
PERC controller card.
Removing a RAID Battery
1
Pull back gently on the right edge of the battery bay and draw out the
RAID battery from the battery carrier.
2
Disconnect the cable between the RAID battery and the storage controller
card. See Figure 3-20.
Installing a RAID Battery
1
2
3
Locate the battery bay on top of the hard drive bays. See Figure 3-1.
With the cable oriented toward the back, angle the left side of the RAID
battery into the left side of the battery bay. See Figure 3-20.
4
5
6
Rotate the right side of the battery down and press into the locked
position.
If not already done, route the battery cable through the right chassis wall.
See "Cable Routing."
Connect the battery cable to the battery connector on the storage
controller. See Figure 3-18.
Installing System Components
109
Cable Routing
Cables that extend through the system front-to-back are routed along a cable
path within the interior right wall of the system chassis. The cables are
secured by a cable retention bracket that attaches to the inner wall.
Removing the Cable Retention Bracket
1
2
3
Remove the cooling shroud. See "Removing the Cooling Shroud."
Remove the cooling fan bracket. See "Removing the Fan Bracket."
Press outward on the blue release latch on the cable retention bracket and
slide the bracket back until the tabs at the bottom of the bracket clear the
chassis. See Figure 3-21.
4
Lift the cable retention bracket off the chassis wall.
Figure 3-21. Removing and Installing the Cable Retention Bracket
3
4
2
1
5
6
1
3
5
cable retention bracket
hooks (3)
2
4
6
release latch
right chassis wall
tab (3)
chassis slots (6)
Installing System Components
111
Installing the Cable Retention Bracket
1
Insert the hooks and tabs of the cable retention bracket into the slots in
the chassis wall and slide the bracket back until the latch engages.
2
3
Install the cooling fan bracket. See "Replacing the Fan Bracket."
Install the cooling shroud. See "Installing the Cooling Shroud."
Expansion Cards and Expansion-Card Risers
The system supports up to four PCI Express (PCIe) expansion cards on two
expansion-card risers.
•
•
Expansion-card riser 1 provides two PCIe x4-link Gen 2 expansion slots.
Expansion-card riser 2 is offered in two versions:
–
The standard expansion-card riser 2 provides two PCIe x8-link Gen 2
expansion slots.
–
The optional expansion-card riser 2 provides one PCIe x16-link Gen 2
expansion slot.
CAUTION: Expansion cards can only be plugged into the slots on the expansion-
card risers. Do not plug any expansion cards into the riser connectors on the
system board.
To identify expansion slots, see "Expansion-Card Riser-Board Components
and PCIe Buses."
Expansion Card Installation Guidelines
Observe the following notes and guidelines regarding the expansion-card
slots:
•
PCI Express Generation 2 and Generation 1 expansion cards are supported
in all slots.
•
In slots 2, 3, and 4, expansion cards can have a maximum length of 24.13
cm (9.5 in). Slot 1 supports a full-length (30.99-cm [12.2-in]) expansion
card.
•
•
The system supports three full-height expansion cards and one low-profile
expansion card (slot 2).
Although slots 1 and 2 are physically PCIe x8 connectors, they function
only as PCIe x4-link slots.
112
Installing System Components
•
•
•
When the optional x16-link riser is installed, slot 4 is not available.
The expansion-card slots are not hot-swappable.
Besides the integrated storage controller, the system supports a maximum
of two PERC or SAS controller expansion cards to manage external
storage.
CAUTION: To ensure proper cooling no more than two of the four expansion cards
can have a power consumption of greater than 15W (up to 25W maximum each),
not including the integrated storage controller.
•
Table 3-1 provides a guide for installing expansion cards to ensure proper
cooling and mechanical fit. The expansion cards with the highest priority
should be installed first using the slot priority indicated. All other
expansion cards should be installed in card priority and slot priority order.
Table 3-1. Expansion-Card Installation Order
Card
Max Greater
Allowed Than 15W?
Priority Card Type
Slot Priority
1
2
3
4
5
6
PERC 5/E controller
1,3,4
2
2
2
2
4
4
Y
Y
Y
Y
N
N
PERC 6/E controller
10 Gb NIC
3,4,1
3,4,1,2
3,4,1
All other Dell storage cards
All other NICs
1
1
2
2
1,2,3,4
1,2,3,4
Non-Dell storage cards
1
2
Maximum of 2 of any card whose maximum power exceeds 15W.
See the expansion card documentation to ensure that the maximum power does not exceed 15W.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: Before installing any expansion cards, see "Expansion Card Installation
Guidelines."
Installing System Components
113
except that slots 3 and 4 on riser 2 have card-edge guides for installing 24.13-cm
(9.5-in) expansion cards.
1
2
Unpack the expansion card and prepare it for installation.
For instructions, see the documentation accompanying the card.
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
3
4
Open the system. See "Opening the System."
Open the expansion-card guide latch and remove the filler bracket at the
back of the system. See Figure 3-22.
NOTE: Keep this bracket in case you need to remove the expansion card.
Filler brackets must be installed over empty expansion-card slots to maintain
FCC certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system.
5
Install the expansion card:
a
b
c
d
If the expansion card is 24.13 cm (9.5 in), align its front edge with the
front card guide. See Figure 3-22.
Position the expansion card so that the card-edge connector aligns
with the expansion-card connector on the expansion-card riser board.
Insert the card-edge connector firmly into the PCIe card connector
until the card is fully seated.
When the card is seated in the connector, close the expansion-card
latch. See Figure 3-22.
6
Connect any expansion-card cables for the new card.
See the documentation that came with the card for information about its
cable connections.
7
8
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
114
Installing System Components
Removing an Expansion Card
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
Open the system. See "Opening the System."
Disconnect any cables connected to the expansion card.
Remove the expansion card:
a
b
Open the expansion-card latch at the back of the system chassis. See
Figure 3-22.
Grasp the expansion card by its top corners, and carefully pull the card
from the expansion-card connector.
5
If you are removing the card permanently, install a metal filler bracket over
the empty expansion slot opening and close the expansion-card latch.
NOTE: You must install a filler bracket over an empty expansion slot to
maintain Federal Communications Commission (FCC) certification of the
system. The brackets also aid in proper cooling and airflow inside the system.
6
7
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
Installing System Components
115
Figure 3-22. Removing or Installing the Expansion Card
4
3
2
5
1
1
3
5
front card guide
2
4
expansion-card riser 2
expansion-card connector
expansion card
expansion-card guide latch
Removing Expansion-Card Riser 1
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: You must remove all expansion cards from the expansion-card riser before
removing the riser from the system.
NOTE: The system will not start with a riser board removed.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
116
Installing System Components
2
3
4
Open the system. See Opening the System.
Disconnect all cables connected to the expansion card.
Remove all expansion cards from the expansion-card riser. See Removing
an Expansion Card.
5
Press the tab at the bottom of the riser to release the board from the card
slot and lift expansion-card riser 1 off of the mounting pins and out of the
system. See Figure 3-23.
Replacing Expansion-Card Riser 1
NOTE: The system will not start with a riser board removed.
1
Aligning the pin collar over the mounting pin on the system board, lower
expansion-card riser 1 until the board connector is firmly seated into the
system board socket. See Figure 3-23.
2
3
4
5
Reinstall any expansion cards. See "Installing an Expansion Card."
Reconnect all expansion-card cables.
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
Installing System Components
117
Figure 3-23. Removing and Replacing Expansion-Card Riser 1
2
1
3
4
1
3
release button
2
4
expansion-card riser 1
system board socket
card edge guides
Removing Expansion-Card Riser 2
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: You must remove all expansion cards from the expansion-card riser before
removing the riser from the system.
NOTE: The system will not start with an expansion-card riser removed.
118
Installing System Components
1
the system from the electrical outlet.
2
3
4
Open the system. See Opening the System.
Disconnect all cables connected to the expansion card.
Remove any expansion cards from the expansion-card riser. See "Removing
an Expansion Card."
5
Press the blue release latch on expansion-card riser 2 and lift the riser
straight up to clear the chassis. See Figure 3-24.
Replacing Expansion-Card Riser 2
1
Align the guides on each end of expansion-card riser 2 with the mounting
pins on the system board, and lower the riser into the system until the
latches on the riser the engage. See Figure 3-24.
2
3
4
5
Reinstall any expansion cards. See "Installing an Expansion Card."
Reconnect all expansion-card cables.
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
Installing System Components
119
Figure 3-24. Removing and Replacing Expansion-Card Riser 2
2
3
1
4
5
1
3
5
expansion-card riser 2
pin collars (2)
2
4
mounting pins (2)
riser 2 connector on system board
Removing Expansion-Card Riser 2 From the Expansion-Card Bracket
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
3
Open the system. See "Opening the System."
Remove any expansion cards from the expansion-card riser 2. See
"Removing an Expansion Card."
4
Remove expansion-card riser 2. See "Removing Expansion-Card Riser 2."
120
Installing System Components
Figure 3-25. Removing and Replacing the Riser 2 Board
2
1
3
4
5
1
3
5
expansion-card bracket
tab slot (4)
2
4
tab hook (4)
riser 2 board
screw
5
Remove the expansion-card riser board:
a
Using a Phillips screwdriver, remove the securing screw from the
b
c
Slide the riser board off of the four securing tab hooks.
Lift the riser board from the bracket.
Replacing the Riser 2 Board on the Expansion-Card Bracket
1
Place the riser board in the expansion-card bracket so that the four tab
hooks are fully inserted through the tab slots on the riser board. See
Figure 3-25.
2
3
Slide the riser board into the tab hooks.
Using a Phillips screwdriver, secure the board with the Phillips screw.
Installing System Components
121
4
5
Reinstall expansion-card riser 2. See "Replacing Expansion-Card Riser 2."
Install all expansion cards in the expansion-card slots. See "Installing an
Expansion Card."
6
7
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
System Memory
Your system supports DDR3 registered DIMMs (RDIMMs) or ECC
unbuffered DIMMs (UDIMMs). Single and dual-rank DIMMs can be 1067-
or 1333-MHz, and quad-rank DIMMs can be 1067-MHz.
The system contains 18 memory sockets split into two sets of nine sockets,
one set for each processor. Each nine-socket set is organized into three
channels of three memory sockets per channel. The first socket of each
channel is marked with white release levers.
The maximum memory that is supported on your system varies according to
the types and sizes of memory modules being used:
•
•
•
Single-rank and dual-rank RDIMMs of sizes 2-GB, 4-GB, and 8-GB
(when available) are supported for a total of up to 144 GB.
Quad-rank RDIMMs (two per channel) are supported for a total of up to
96 GB.
1-GB and 2-GB UDIMMs are supported for a total of up to 24 GB.
General Memory Module Installation Guidelines
To ensure optimal performance of your system, observe the following general
guidelines when configuring your system memory.
NOTE: Memory configurations that fail to observe these guidelines can cause your
system to halt at startup without any video output of system messages.
•
•
•
RDIMMs and UDIMMs cannot be mixed.
No more than two UDIMMs can be populated per channel.
Except for memory channels that are unused, all populated memory
channels must have identical configurations.
122
Installing System Components
•
•
In a dual-processor configuration, the memory configuration for each
processor must be identical.
Memory modules of different sizes can be mixed within a memory channel
(for example, 2-GB, 8-GB, and 4-GB), but all populated channels must
have identical configurations.
•
•
For Optimizer Mode, memory modules are installed in the numeric order
of the sockets beginning with A1 or B1.
For Memory Mirroring or Advanced ECC Mode, the three sockets furthest
from the processor are unused and memory modules are installed
beginning with socket A2 or B2 and proceeding in the numeric order of the
remaining sockets (for example, A2, A3, A5, A6, A8, and A9).
•
•
Advanced ECC Mode requires x4 or x8 DRAM device widths.
The memory speed of each channel depends on the memory
configuration:
–
For single or dual-rank memory modules:
•
•
•
One memory module per channel supports up to 1333 MHz.
Two memory modules per channel supports up to 1067 MHz.
Three memory modules per channel are limited to 800 MHz,
regardless of memory module speed.
–
For quad-rank memory modules:
•
•
One memory module per channel supports up to 1067 MHz.
Two memory modules per channel are limited to 800 MHz,
regardless of memory module speed.
•
•
If a quad-rank memory module is installed, then only one other memory
module can be added to that channel.
If quad-rank memory modules are mixed with single- or dual-rank
modules, the quad-rank modules must be installed in the sockets with the
white release levers.
•
If memory modules with different speeds are installed, they will operate at
the speed of the slowest installed memory module(s).
Installing System Components
123
Mode-Specific Guidelines
Three memory channels are allocated to each processor. The number of
channels and allowable configurations depend on the memory mode selected.
Advanced ECC (Lockstep) Mode Support
In this configuration, the two channels closest to the processor are combined
to form one 128-bit channel. This mode supports SDDC for both x4- and x8-
based memory modules. Memory modules must be identical in size, speed,
and technology in corresponding slots.
Memory Mirroring Support
The system supports memory mirroring if identical memory modules are
installed in the two channels closest to the processor (memory is not installed
in the farthest channel). Mirroring must be enabled in the System Setup
program. In a mirrored configuration, the total available system memory is
one-half of the total installed physical memory.
Optimizer (Independent Channel) Mode
In this mode, all three channels are populated with identical memory
modules. This mode permits a larger total memory capacity but does not
support SDDC with x8-based memory modules.
A minimal single-channel configuration of one 1-GB memory module per
processor is also supported in this mode.
Table 3-2 and Table 3-3 show sample memory configurations that follow the
appropriate memory guidelines stated in this section. The samples show
identical memory-module configurations and their physical and available
memory totals. The tables do not show mixed or quad-rank memory-module
configurations, nor do they address the memory speed considerations of any
configuration.
124
Installing System Components
Table 3-2. Sample RDIMM Single- and Dual-Rank Memory Configurations (Per
Processor)
Memory Sockets
Single Processor
Dual Processor
Memory
Memory Module
1
2
3
Physical Available Physical Available
Memory Memory Memory Memory
4
5
6
Mode
Size
7
8
9
(GB)
(GB)
(GB)
(GB)
Optimizer 2-GB
X
X
X
2
all
4
all
X
X
4
6
8
X
12
8
X X
X X
X X
4
X X
X X
8
16
24
24
36
X X
12
12
18
X X X X X X
X X X X X X X X X
4-GB
X
4
all
8
all
X
X
X
8
16
24
16
32
48
48
72
X
X
12
8
X X
X X
X X
X X
X X
16
24
24
36
X X
X X X X X X
X X X X X X X X X
1
8-GB
X
8
all
16
32
48
32
64
96
96
144
all
X
X
X
16
24
16
32
48
48
72
X
X
X X
X X
X X
X X
X X
X X
X X X X X X
X X X X X X X X X
Installing System Components
125
Table 3-2. Sample RDIMM Single- and Dual-Rank Memory Configurations (Per
Processor)
Memory Sockets
Single Processor
Dual Processor
Memory
Module
Size
1
2
3
Physical Available Physical Available
Memory Memory Memory Memory
Memory
Mode
4
5
6
7
8
9
(GB)
(GB)
(GB)
(GB)
Advanced 2-GB
vacant
vacant
vacant
vacant
vacant
vacant
X
X X
X
X X
4
all
8
all
2
ECC
8
16
24
X X X X X X
12
4-GB
8-GB
X
X X
X
X X
8
all
all
16
32
48
all
all
16
24
X X X X X X
1
X
X X
X
X X
16
32
48
32
64
96
X X X X X X
Mirroring 2-GB
X
X X
X
X X
4
8
2
4
6
8
4
8
16
24
X X X X X X
12
12
4-GB
X
X X
X
X X
8
4
8
16
32
48
8
16
24
16
24
X X X X X X
12
1
8-GB
X
X X
X
X X
16
32
48
8
32
64
96
16
32
48
16
24
X X X X X X
1 When available
2 Requires x4- or x8-based memory modules
126
Installing System Components
Table 3-3. Sample UDIMM Memory Configurations (Per Processor)
Memory Sockets Single Processor
Memory
Dual Processor
1
2
3
Physical Available Physical Available
Memory Memory Memory Memory
Memory Module
Size
4
5
6
Mode
7
8
9
(GB)
(GB)
(GB)
(GB)
Optimizer 1-GB
X
X
X
1
all
2
all
X
X
2
3
4
6
4
6
X
X X
X X
X X
X X
8
X X
12
2-GB
X
2
4
all
4
all
X
X
8
X
X
X
6
12
16
24
X X
X X
X X
X X
8
X X
12
Advanced 1-GB
vacant
vacant
vacant
vacant
X
X X
X
X X
2
4
all
all
4
8
all
all
1
ECC
2-GB
Mirroring 1-GB
2-GB
X
X X
X
X X
4
8
8
16
X
X X
X
X X
2
4
1
2
4
8
2
4
X
X X
X
X X
4
8
2
4
8
4
8
16
1 Requires x4- or x8-based memory modules
Installing Memory Modules
WARNING: The memory modules are hot to the touch for some time after the
system has been powered down. Allow time for the memory modules to cool
before handling them. Handle the memory modules by the card edges and avoid
touching the components on the memory module.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Installing System Components
127
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
5
Open the system. See "Opening the System."
Remove the cooling shroud. See "Removing the Cooling Shroud."
Locate the memory module sockets. See Figure 6-2.
Press outward on the memory module ejectors to allow the memory
module to be inserted into the socket. See Figure 3-26.
Figure 3-26. Installing and Removing the Memory Module
1
2
3
1
3
memory module
alignment key
2
memory module socket ejectors (2)
touch the components on the module.
6
Align the memory module's edge connector with the alignment key of the
memory module socket, and insert the memory module in the socket.
NOTE: The memory module socket has an alignment key that allows you to
install the memory module in the socket in only one way.
7
Press down on the memory module with your thumbs until the ejectors
lock into position. See Figure 3-26.
128
Installing System Components
When the memory module is properly seated in the socket, the ejectors on
the memory module socket align with the ejectors on the other sockets
that have memory modules installed.
8
9
Repeat step 5 through step 7 of this procedure to install the remaining
memory modules. See Table 3-2 or Table 3-3.
Replace the cooling shroud. See "Installing the Cooling Shroud."
10 Close the system. See "Closing the System."
on the system.
12 Press <F2> to enter the System Setup program, and check the System
Memory setting on the main System Setup screen.
The system should have already changed the value to reflect the newly
installed memory.
13 If the value is incorrect, one or more of the memory modules may not be
installed properly. Repeat step 2 through step 12 of this procedure,
checking to ensure that the memory modules are firmly seated in their
sockets.
14 Run the system memory test in the system diagnostics. See "Running the
Embedded System Diagnostics."
Removing Memory Modules
WARNING: The memory modules are hot to the touch for some time after the
system has been powered down. Allow time for the memory modules to cool
before handling them. Handle the memory modules by the card edges and avoid
touching the components on the memory module.
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
Open the system. See "Opening the System."
Installing System Components
129
3
4
5
Remove the cooling shroud. See "Removing the Cooling Shroud."
Locate the memory module sockets. See Figure 6-2.
Press down and out on the ejectors on each end of the socket until the
memory module pops out of the socket. See Figure 3-26.
CAUTION: Handle each memory module only by the card edges, ensuring not to
touch the components on the module.
6
7
8
Reinstall the cooling shroud.
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
Processors
Removing a Processor
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
Prior to upgrading your system, download the latest system BIOS version
from support.dell.com and follow the instructions included in the
compressed download file to install the update on your system
.
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet. When disconnected from AC power,
press and hold the power button for 3 seconds to fully drain the system of
stored power prior to removing the cover.
NOTE: It is recommended that you always use a static mat and static strap
while working on components in the interior of the system.
3
4
Open the system. See "Opening the System."
Remove the cooling shroud. See "Removing the Cooling Shroud."
WARNING: The heat sink and processor are hot to the touch for some time after
the system has been powered down. Allow the heat sink and processor to cool
before handling them.
130
Installing System Components
CAUTION: Never remove the heat sink from a processor unless you intend to
remove the processor. The heat sink is necessary to maintain proper thermal
conditions.
5
6
7
8
Release one of the heat-sink release levers. See Figure 3-27.
Wait 30 seconds for the heat sink to loosen from the processor.
Release the other heat-sink release lever.
Gently lift the heat sink off of the processor and set the heat sink aside
upside down (thermal grease side facing up).
Figure 3-27. Installing and Removing the Heat Sink
2
1
1
heat sink
2
release lever (2)
Installing System Components
131
CAUTION: The processor is held in its socket under strong pressure. Be aware
that the release lever can spring up suddenly if not firmly grasped.
9
Position your thumb firmly over the processor socket-release lever and
release the lever from the locked position by pushing down and pulling out
from under the tab. Rotate the lever 90 degrees upward until the processor
is released from the socket. See Figure 3-28.
10 Use the tab on the processor shield to rotate processor shield upward and
out of the way. See Figure 3-28.
Figure 3-28. Removing the Processor
2
3
1
4
1
3
socket-release lever
processor shield
2
4
processor
ZIF socket
CAUTION: Be careful not to bend any of the pins on the ZIF socket when removing
the processor. Bending the pins can permanently damage the system board.
11 Carefully, lift the processor out of the socket and leave the release lever up
so that the socket is ready for the new processor.
After removing the processor, place it in an antistatic container for reuse,
return, or temporary storage. Do not touch the bottom of the processor.
Touch only the side edges of the processor.
132
Installing System Components
If you are permanently removing the processor, you must install a processor
blank and a heat-sink blank in the CPU2 socket to ensure proper system
cooling. Adding the blank is similar to installing a processor. See "Installing
a Processor."
Installing a Processor
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: In a single-processor configuration, the CPU1 socket must be used.
1
2
If you are adding a second processor for the first time, remove the
heat-sink blank and the processor blank from the vacant processor socket.
Removing the blanks is similar to removing a processor. See "Removing a
Processor."
Remove the processor from the packing material by the processor’s edges
only. Do not touch the bottom of the processor. Handle the processor
carefully with your fingers on the side edges. Place your hand beneath the
3
4
Locate the pin 1 indicator on the system board socket.
Locate the pin 1 indicator on the top of the processor. The pin 1 indicator
is shown as a triangle on the top of the processor. See Figure 3-29.
system board or the processor. Be careful not to bend the pins in the socket.
5
6
Place the processor over the socket with each pin 1 aligned and level. See
Figure 3-29.
CAUTION: Do not use force to seat the processor. When the processor is
positioned correctly, it engages easily into the socket.
Align the notches in the
socket. See Figure 3-29.
p
rocessor with the socket keys on the ZIF
Installing System Components
133
7
Install the processor in the socket. Keep the processor level (see
Figure 3-29) and insert it straight down into the socket. Allow the
processor to float on the pins, allowing the processor shield to hold it in
place.
Figure 3-29. Installing and Removing the Processor
3
2
4
1
5
7
6
1
3
5
7
socket-release lever
processor shield
socket key (2)
2
4
6
processor
notch in processor (2)
ZIF socket
pin 1 indicators (2)
8
Verify that the processor is properly aligned and seated.
Close the processor shield. See Figure 3-30.
9
134
Installing System Components
10 Rotate the socket-release lever down until it snaps into place.
Figure 3-30. Closing the Processor Shield
2
1
3
1
3
socket-release lever
processor shield
2
processor
11 Install the heat sink.
NOTE: Your kit may contain a replacement heat sink if you are installing a
processor that consumes additional power. The new heat sink may not appear
different than the original one; however, it has improved thermal dissipation
specifications and must be used.
a
Using a clean lint-free cloth, remove the thermal grease from the heat
sink.
in contact with and contaminating the processor socket.
b
Open the grease packet included with your processor kit and apply a
spot of thermal grease equal to the size of a finger nail to the top
center of the new processor.
c
d
Place the heat sink on the processor. See Figure 3-27
.
Close the heat-sink release levers or replace the screws at the corners
of the heat sink. See Figure 3-27
.
Installing System Components
135
12 Replace the cooling shroud. See "Installing the Cooling Shroud."
13 Close the system. See "Closing the System."
14 Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
15 Press <F2> to enter the System Setup program, and check that the processor
information matches the new system configuration. See "Entering the
System Setup Program."
16 Run the system diagnostics to verify that the new processor operates
correctly.
See "Running the Embedded System Diagnostics" for information about
running the diagnostics.
System Battery
Replacing the System Battery
WARNING: There is a danger of a new battery exploding if it is incorrectly
installed. Replace the battery only with the same or equivalent type recommended
by the manufacturer. See your safety information for additional information.
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
4
Open the system. See "Opening the System."
Remove the fan bracket. See "Removing the Fan Bracket."
Locate the battery socket. See "System Board Connectors."
.
CAUTION: To avoid damage to the battery connector, you must firmly support the
connector while installing or removing a battery.
5
Remove the system battery.
a
Support the battery connector by pressing down firmly on the positive
side of the connector.
136
Installing System Components
b
Press the battery toward the positive side of the connector and lift it
up out of the securing tabs at the negative side of the connector.
Figure 3-31. Replacing the System Battery
1
2
3
1
3
positive side of battery connector
negative side of battery connector
2
system battery
6
Install the new system battery.
a
b
c
Support the battery connector by pressing down firmly on the positive
side of the connector.
Hold the battery with the "+" facing up, and slide it under the
securing tabs at the positive side of the connector.
place.
7
8
9
Replace the fan bracket. See "Replacing the Fan Bracket."
Close the system. See "Closing the System."
Reconnect the system to the electrical outlet and turn the system on,
including any attached peripherals.
10 Enter the System Setup program to confirm that the battery is operating
properly. See "Entering the System Setup Program."
11 Enter the correct time and date in the System Setup program's Time and
Date fields, and re-enter any customized option settings as needed.
12 Exit the System Setup program.
Installing System Components
137
Control Panel Assembly
NOTE: The control panel assembly consists of two separate modules—the display
module and the control panel circuit board. Use the following instructions to
remove and install either module.
Removing the Control Panel Display Module
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and peripherals.
2
3
Open the system. See "Opening the System."
Disconnect the display module cable from the control panel board. See
Figure 3-32.
4
Using a knife or a small flat-blade screwdriver, insert the blade beneath the
front panel of the display and slide the blade across the bottom to lift the
panel outward. See Figure 3-32.
5
6
Using a T10 Torx driver, remove the two screws that secure the display
module to the system chassis.
7
Installing the Control Panel Display Module
1
Insert the display module into the chassis cutout and secure with the two
Torx screws. See Figure 3-32.
2
3
4
5
Attach the replacement panel to the front of the display module.
Connect the display module cable to the control panel board.
Close the system. See "Closing the System."
Reconnect the system to the power source and turn on the system and
attached peripherals.
138
Installing System Components
Figure 3-32. Removing and Installing the Control Panel
4
3
2
1
5
6
1
3
5
front panel screw (Torx)
control panel board
2
4
6
display module cable
control panel cable
display module
mounting screws (3 Torx)
Removing the Control Panel Board
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Installing System Components
139
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and peripherals.
2
3
Open the system. See "Opening the System."
Disconnect the display module cable from the control panel board. See
Figure 3-32.
4
Disconnect the control panel cable at back of the control panel board. See
Figure 3-32.
5
6
Disconnect the internal SD module cable.
If present, remove the internal USB memory key.
CAUTION: Do not pull on the cable to unseat the connector. Doing so can damage
the cable.
7
8
Using a T8 Torx driver, remove the screw on the front panel located
beneath the left USB connector. See Figure 3-32.
Using a T10 Torx driver, remove the three screws that secure the control
panel board to the system chassis and remove the board.
Installing the Control Panel Board
1
Install the front panel screw in the screw hole located beneath the left USB
connector. See Figure 3-32.
2
Install the control panel board in the system chassis and secure with the
three Torx screws. See Figure 3-32.
3
4
5
6
7
8
Connect the display module cable to the control panel board.
Connect the control panel cable to the control panel board.
Connect the internal SD module cable.
Install the internal USB memory key.
Close the system. See "Closing the System."
Reconnect the system to the power source and turn on the system and
attached peripherals.
140
Installing System Components
SAS Backplane
Removing the SAS Backplane
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
If applicable, remove the bezel. See "Removing the Front Bezel."
from the electrical outlet.
3
Open the system. See "Opening the System."
CAUTION: To prevent damage to the drives and backplane, you must remove the
SAS drives from the system before removing the backplane.
CAUTION: You must note the number of each hard drive and temporarily label
them before removal to ensure that you can replace them in the same locations.
4
5
6
7
Remove all hard drives. See "Removing a Hot-Swap Hard Drive."
Disconnect the power cable from the end of the SAS backplane.
Disconnect the SAS data cables from the backplane.
Remove the SAS backplane from the system:
a
b
While pulling the blue latch toward the front of the system, slide the
backplane upward. See Figure 3-33.
When the backplane cannot slide upward any farther, pull the
backplane toward the back of the system to remove it from the
retention hooks.
c
d
Lift the board out of the system, being careful to avoid damaging
components on the face of the board.
Place the SAS backplane face down on a work surface.
Installing System Components
141
Figure 3-33. Removing and Installing the SAS Backplane
3
4
5
2
1
6
7
8
1
3
5
7
drive bays
2
4
6
8
SAS backplane board
SAS A cable
power cable from system board
SAS B cable
securing slots (8)
securing tabs (7)
SAS backplane board release tab
Installing a SAS Backplane
1
Lower the backplane into the system, being careful to avoid damaging
components on the face of the board.
2
Align the slots in the backplane with the retention hooks on the back of
the drive bays, then move the backplane forward until the retention hooks
fit through the slots in the backplane. See Figure 3-33.
142
Installing System Components
3
Slide the backplane downward until the blue retention latch locks into
place.
4
5
6
7
Connect the SAS data and power cables to the SAS backplane.
Install the hard drives in their original locations.
Close the system. See "Closing the System."
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
System Board
Removing the System Board
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: If your system uses the Trusted Platform Module (TPM) with an
encryption program, you must supply the recovery key for your data before you can
access the encrypted data on your hard drives. See the documentation for your
encryption software for more information.
Server Configurator repository to the latest software to restore full functionality.
See the Unified Server Configurator user documentation for more information.
1
from the electrical outlet.
2
3
4
5
Remove the power supply(ies). See "Removing a Power Supply."
Remove the cooling shroud. See "Removing the Cooling Shroud."
Remove all expansion cards and the integrated storage controller card. See
"Removing an Expansion Card" and "Removing the Integrated Storage
Controller Card."
6
If installed, remove the NIC hardware key from the system board. See
"NIC Hardware Key."
Installing System Components
143
7
Remove the two riser boards. See "Removing Expansion-Card Riser 1" and
"Removing Expansion-Card Riser 2."
8
9
Remove the fan bracket. See "Removing the Fan Bracket."
CAUTION: To prevent damage to the drives and backplane, you must remove the
SAS drives from the system before removing the backplane.
CAUTION: You must note the number of each hard drive and temporarily label
them before removal to ensure that you can replace them in the same locations.
a
b
Remove all hard drives. See "Removing a Hot-Swap Hard Drive."
Disconnect the power and interface cables from the SAS backplane.
See Figure 3-33.
c
d
Pull the blue latch toward the front of the system and slide the
backplane upward.
When the backplane cannot slide upward any farther, pull the
backplane toward the back of the system to remove it from the
retention hooks.
e
f
Lift the board out of the system, being careful to avoid damaging
components on the face of the board.
Place the SAS backplane face down on a work surface.
10 Disconnect all cables from the system board.
11 Remove the system board assembly:
a
Pull up the spring-loaded blue retention pin located in the center of
the system board, and then slide the system board assembly toward
the front end of the chassis.
WARNING: Do not lift the system board by the memory modules latches,
processor heatsink, or any component on the system board.
b
Grasp the system board assembly by the edges of the system board
tray, and lift the assembly from the chassis. See Figure 3-34.
144
Installing System Components
Figure 3-34. System Board Removal
1
2
1
system-board tray riser release pin
2
system board
Installing the System Board
1
2
3
4
Unpack the new system board and remove the label placard that is inserted
in the memory module socket.
Remove the labels from the placard and affix them to the information tag
on the front of the system. See Figure 1-1.
Transfer the processors and heat sinks to the new system board. See
"Removing a Processor."
Remove the memory modules and transfer them to the same locations on
the new board. See "Removing Memory Modules" and "Installing Memory
Modules."
5
Install the new system board:
a
b
Angle the system board as you lower it into the chassis and set the
board flat inside the chassis.
Maneuver the system board so that all of the retention hooks on the
chassis are inserted into the retention slots on the system board.
Installing System Components
145
c
Push the system board toward the back of the chassis until the blue
retention pin locks into place.
6
7
If applicable, transfer the NIC hardware key.
Replace the riser boards. See "Replacing Expansion-Card Riser 1" and
"Replacing Expansion-Card Riser 2."
8
9
Reinstall the integrated storage controller card. See "Installing the
Integrated Storage Controller Card."
If applicable, reconnect the RAID battery cable to the storage controller
card.
of the connectors on the system board).
11 If removed, reinstall the SAS backplane and all hard drives. See "System
Board."
12 Install all expansion cards. See "Installing an Expansion Card."
13 If applicable, transfer the iDRAC6 Enterprise card to the new system
board. See "Installing an iDRAC6 Enterprise Card."
14 Replace the fan bracket. See "Replacing the Fan Bracket."
15 Replace the cooling shroud. See "Installing the Cooling Shroud."
16 Close the system. See "Closing the System."
17 Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
146
Installing System Components
Troubleshooting Your System
Safety First—For You and Your System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Troubleshooting System Startup Failure
If your system halts during startup prior to video imaging or LCD messaging,
especially after installing an operating system or reconfiguring your system’s
hardware, check for the following conditions.
•
If you boot the system in BIOS boot mode after installing an operating
system in UEFI boot mode, the system will hang. The reverse is also true.
You must boot to the same boot mode in which you installed the operating
system. See "Using the System Setup Program and UEFI Boot Manager."
•
Invalid memory configurations could cause the system to halt at startup
without any video output. See "System Memory."
For all other startup issues, note the LCD panel messages and any system
messages that appear on-screen. See "LCD Status Messages" and "System
Messages" for more information.
Troubleshooting External Connections
Ensure that all external cables are securely attached to the external
connectors on your system before troubleshooting any external devices. See
Figure 1-1 and Figure 1-4 for the front- and back-panel connectors on your
system.
Troubleshooting Your System
147
Troubleshooting the Video Subsystem
1
2
3
Check the video interface cabling from the system to the monitor.
If two monitors are attached to the system, disconnect one monitor. The
system supports only one monitor attached to either the front or back
video connector.
4
5
Try using a monitor that is known to be working.
Run the appropriate online diagnostic test. See "Using Dell Online
Diagnostics."
If the tests run successfully, the problem is not related to video hardware.
If the tests fail, see "Getting Help."
Troubleshooting a USB Device
1
Use the following steps to troubleshoot a USB keyboard and/or mouse. For
other USB devices, go to step 2.
a
b
Disconnect the keyboard and mouse cables from the system briefly
and reconnect them.
Connect the keyboard/mouse to the USB port(s) on the opposite side
of the system.
If the problem is resolved, restart the system, enter the System Setup
program, and check if the nonfunctioning USB ports are enabled.
c
Replace the keyboard/mouse with another working keyboard/mouse.
If the problem is resolved, replace the faulty keyboard/mouse.
If the problem is not resolved, proceed to the next step to begin
troubleshooting the other USB devices attached to the system.
2
3
Power down all attached USB devices and disconnect them from the
system.
Restart the system and, if your keyboard is functioning, enter the system
setup program. Verify that all USB ports are enabled. See "Integrated
Devices Screen."
If your keyboard is not functioning, you can also use remote access.
148
Troubleshooting Your System
4
5
Reconnect and power on each USB device one at a time.
If a device causes the same problem, power down the device, replace the
USB cable, and power up the device.
If the problem persists, replace the device.
If all troubleshooting fails, see "Getting Help."
Troubleshooting a Serial I/O Device
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Swap the serial interface cable with another working cable, and turn on the
system and the serial device.
If the problem is resolved, replace the interface cable.
3
4
Turn off the system and the serial device, and swap the device with a
comparable device.
Turn on the system and the serial device.
If the problem is resolved, replace the serial device.
If the problem persists, see "Getting Help."
Troubleshooting a NIC
1
2
3
Run the appropriate online diagnostic test. See "Using Dell Online
Diagnostics."
Restart the system and check for any system messages pertaining to the
NIC controller.
Check the appropriate indicator on the NIC connector. See "NIC Indicator
Codes."
•
•
If the link indicator does not light, check all cable connections.
If the activity indicator does not light, the network driver files might
be damaged or missing.
•
Use another connector on the switch or hub.
If you are using a NIC card instead of an embedded NIC, see the
documentation for the NIC card.
Troubleshooting Your System
149
4
5
6
Ensure that the appropriate drivers are installed and the protocols are
bound. See the NIC's documentation.
Enter the System Setup program and confirm that the NIC ports are
enabled. See "Integrated Devices Screen."
Ensure that the NICs, hubs, and switches on the network are all set to the
same data transmission speed and duplex. See the documentation for each
network device.
7
Ensure that all network cables are of the proper type and do not exceed the
maximum length.
If all troubleshooting fails, see "Getting Help."
Troubleshooting a Wet System
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
3
Open the system. See "Opening the System."
Disassemble components from the system. See "Installing System
Components."
•
•
•
•
•
•
•
•
•
Cooling shroud
Hard drives
SD cards
USB memory key
NIC hardware key
Internal SD Module
Expansion cards and both expansion-card risers
Integrated storage controller
iDRAC6 Enterprise card
150
Troubleshooting Your System
•
•
•
•
Power supplies
Processors and heat sinks
Memory modules
Fan bracket
4
5
Let the system dry thoroughly for at least 24 hours.
Reinstall the processors and heat sinks, memory modules, power supplies,
cooling shroud, and fan bracket.
6
7
Close the system. See "Closing the System."
Reconnect the system to the electrical outlet, and turn on the system.
If the system does not start properly, see "Getting Help."
8
9
If the system starts properly, shut down the system and reinstall the rest of
the components that you removed in step 3. See "Installing an Expansion
Card."
Run the appropriate online diagnostic test. See "Running the Embedded
System Diagnostics."
If the tests fail, see "Getting Help."
Troubleshooting a Damaged System
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
3
Open the system. See "Opening the System."
Ensure that the following components are properly installed:
•
•
•
•
Expansion cards and both expansion-card risers
Power supplies
Fans and cooling shroud
Processors and heat sinks
Troubleshooting Your System
151
•
•
Memory modules
Hard-drive carriers
4
5
6
Ensure that all cables are properly connected.
Close the system. See "Closing the System."
Run the system board tests in the system diagnostics. See "Running the
Embedded System Diagnostics."
If the tests fail, see "Getting Help."
Troubleshooting the System Battery
1
the System Setup Program and UEFI Boot Manager."
2
Turn off the system and disconnect it from the electrical outlet for at least
one hour.
3
4
Reconnect the system to the electrical outlet and turn on the system.
Enter the System Setup program.
If the date and time are not correct in the System Setup program, replace
the battery. See "System Battery."
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
If the problem is not resolved by replacing the battery, see "Getting Help."
Troubleshooting Power Supplies
CAUTION: At least one power supply must be installed for the system to operate.
Operating the system with only one power supply installed for extended periods of
time without a power-supply blank installed in the PS2 power-supply bay can
cause the system to overheat.
1
Identify the faulty power supply by the power supply's status indicator. See
"Power Indicator Codes."
152
Troubleshooting Your System
CAUTION: If troubleshooting a power supply mismatch error, replace only the
power supply with the flashing indicator. Swapping the opposite power supply to
make a matched pair can result in an error condition and unexpected system
shutdown. To change from a High Output configuration to an Energy Smart
configuration or vice versa, you must power down the system.
2
Reseat the power supply by removing and reinstalling it. See "Removing a
Power Supply" and "Replacing a Power Supply."
NOTE: After installing a power supply, allow several seconds for the system
to recognize the power supply and to determine if it is working properly. The
status indicator turns green to signify that the power supply is functioning
properly.
If the problem persists, replace the faulty power supply with the same type
of power supply.
3
If the problem persists, see "Getting Help."
Troubleshooting System Cooling Problems
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Ensure that none of the following conditions exist:
•
•
•
•
System cover, cooling shroud, drive blank, power supply blank (in single
power supply configurations), or front or back filler panel is removed.
FAN5 blank or heat sink blank is removed in single-processor
configurations.
The expansion card installation guidelines have not been followed. See
"Expansion Card Installation Guidelines."
Ambient temperature is too high. See your Getting Started Guide for the
system’s operating temperature requirements.
•
•
External airflow is obstructed.
Cables inside the system obstruct airflow.
Troubleshooting Your System
153
•
An individual cooling fan is removed or has failed. See "Troubleshooting a
Fan."
Troubleshooting a Fan
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Open the system. See "Opening the System."
CAUTION: The cooling fans are hot-swappable. To maintain proper cooling while
the system is on, only replace one fan at a time.
2
3
Locate the faulty fan indicated by the LCD panel or the diagnostic
software.
Reseat the fan. See "Removing a Cooling Fan" and "Replacing a Cooling
Fan."
NOTE: Wait at least 30 seconds for the system to recognize the fan and
determine whether it is working properly.
4
If the problem is not resolved, install a new fan.
If the replacement fan does not operate, see "Getting Help."
Troubleshooting System Memory
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: Invalid memory configurations can cause your system to halt at startup
without video output. See "General Memory Module Installation Guidelines" and
verify that your memory configuration complies with all applicable guidelines.
1
If the system is operational, run the appropriate online diagnostic test. See
"Using Dell Online Diagnostics."
154
Troubleshooting Your System
If diagnostics indicates a fault, follow the corrective actions provided by
the diagnostic program.
2
3
If the system is not operational, turn off the system and attached
seconds and then reconnect the system to power.
Turn on the system and attached peripherals and note the messages on the
screen or LCD panel.
Go to step 14 if an error message appears indicating a fault with a specific
memory module.
4
See "Memory Settings Screen." Make any changes to the memory settings,
if needed.
If the memory settings match the installed memory but a problem is still
indicated, go to step 14.
5
from the electrical outlet.
6
7
8
Open the system. See "Opening the System."
Remove the cooling shroud. See "Removing the Cooling Shroud."
Check the memory channels and ensure that they are populated correctly.
See "General Memory Module Installation Guidelines."
9
Modules."
10 Replace the cooling shroud. See "Installing the Cooling Shroud."
11 Close the system. See "Closing the System."
12 Reconnect the system to its electrical outlet, and turn on the system and
attached peripherals.
13 Enter the System Setup program and check the system memory setting.
See "Memory Settings Screen."
If the problem is not resolved, proceed with the next step.
14 Turn off the system and attached peripherals, and disconnect the system
from the power source.
15 Open the system. See "Opening the System."
Troubleshooting Your System
155
17 If a diagnostic test or error message indicates a specific memory module as
faulty, swap or replace the module.
18 To troubleshoot an unspecified faulty memory module, replace the
memory module in the first DIMM socket with a module of the same type
and capacity. See "Installing Memory Modules."
19 Replace the cooling shroud. See "Installing the Cooling Shroud."
20 Close the system. See "Closing the System."
21 Reconnect the system to its electrical outlet, and turn on the system and
attached peripherals.
22 As the system boots, observe any error message that appears on the screen
or the LCD panel on the front of the system.
23 If the memory problem is still indicated, repeat step 14 through step 22 for
each memory module installed.
If the problem persists after all memory modules have been checked, see
"Getting Help."
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
Enter the System Setup program and ensure that the internal SD card port
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
3
4
Open the system. See "Opening the System."
Reseat the internal SD module cable. See "Installing the Internal SD
Module."
5
Locate the SD card and reseat it. See "Removing the Internal SD Flash
Card" and "Installing the Internal SD Flash Card."
156
Troubleshooting Your System
6
7
Close the system. See "Closing the System."
Turn on the system and attached peripherals and check if the SD card is
functioning.
8
9
If the problem is not resolved, repeat step 2 and step 3.
Insert a different SD card that you know works properly.
10 Close the system. See "Closing the System."
11 Turn on the system and attached peripherals and check if the SD card is
functioning.
If the problem is not resolved, see "Getting Help."
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
port is enabled. See "Integrated Devices Screen."
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
3
4
Open the system. See "Opening the System."
Locate the internal USB key and reseat it. See "Internal USB Memory
Key."
5
6
Close the system. See "Closing the System."
Turn on the system and attached peripherals and check if the USB key is
functioning.
7
8
9
If the problem is not resolved, repeat step 2 and step 3.
Insert a different USB key that you know works properly.
Close the system. See "Closing the System."
Troubleshooting Your System
157
10 Turn on the system and attached peripherals and check if the USB key is
functioning.
If the problem is not resolved, see "Getting Help."
Troubleshooting an Optical Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
3
Try using a different DVD.
Ensure that the device drivers for the optical drive are installed and are
configured correctly
4
5
6
Enter the System Setup program and ensure that the drive’s controller is
enabled. See "Using the System Setup Program and UEFI Boot Manager."
Run the appropriate online diagnostic test. See "Using Dell Online
Diagnostics."
from the electrical outlet.
7
8
Open the system. See "Opening the System."
Ensure that the interface cable is securely connected to the optical drive
and to the system board. See "Optical Drive."
9
Ensure that a power cable is properly connected to the drive and the
system board.
10 Close the system. See "Closing the System."
11 Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
If the problem is not resolved, see "Getting Help."
158
Troubleshooting Your System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Run the appropriate online diagnostic test. See "Using Dell Online
Diagnostics."
Depending on the results of the diagnostics test, proceed as needed
through the following steps.
2
3
Remove the bezel. See "Removing the Front Bezel."
If your hard drives are configured in a RAID array, perform the following
steps.
a
Restart the system and enter the host adapter configuration utility
program by pressing <Ctrl><R> for a PERC controller or
<Ctrl><C> for a SAS controller.
See the documentation supplied with the host adapter for information
about the configuration utility.
b
c
d
Ensure that the hard drive(s) have been configured correctly for the
RAID array.
Take the hard drive offline and then reseat the hard drive. See
"Removing a Hot-Swap Hard Drive."
Exit the configuration utility and allow the system to boot to the
operating system.
4
5
Ensure that the required device drivers for your controller card are installed
and are configured correctly. See the operating system documentation for
more information.
Restart the system, enter the System Setup program, and verify that the
controller is enabled and the drives appear in the System Setup program.
See "Using the System Setup Program and UEFI Boot Manager."
If the problem persists, see "Troubleshooting a Storage Controller."
Troubleshooting Your System
159
.
NOTE: When troubleshooting a SAS or PERC controller, also see the
documentation for your operating system and the controller.
1
2
Run the appropriate online diagnostic test. See "Running the Embedded
System Diagnostics."
Enter the System Setup program and ensure that the SAS or PERC
controller is enabled. See "Using the System Setup Program and UEFI
Boot Manager."
3
Restart the system and press the applicable key sequence to enter the
configuration utility program:
•
•
<Ctrl><C> for a SAS controller
<Ctrl><R> for a PERC controller
See the controller's documentation for information about configuration
settings.
4
Check the configuration settings, make any necessary corrections, and
restart the system.
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
5
Turn off the system and attached peripherals, and disconnect the system
from its electrical outlet.
6
7
Open the system. See "Opening the System."
Ensure that the controller card is firmly seated into the expansion-card
connector. See "Installing the Integrated Storage Controller Card."
8
9
If you have a battery-cached PERC controller, ensure that the RAID
battery is properly connected and, if applicable, the memory module on
the PERC card is properly seated.
Verify that the cable connections between the SAS backplane and the
integrated storage controller are correct. See "Installing the Integrated
Storage Controller Card" and Figure 3-18.
160
Troubleshooting Your System
10 Ensure that the cables are firmly connected to the storage controller and
the SAS backplane board.
11 Close the system. See "Closing the System."
12 Reconnect the system to its electrical outlet, and turn on the system and
attached peripherals.
If the problem persists, see "Getting Help."
Troubleshooting Expansion Cards
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: When troubleshooting an expansion card, see the documentation for your
operating system and the expansion card.
1
2
Run the appropriate online diagnostic test. See "Using Dell Online
Diagnostics."
from the electrical outlet.
3
4
Open the system. See "Opening the System."
card installation guidelines. See "Expansion Card Installation Guidelines."
5
Reseat any expansion card that is not firmly seated in its connector. See
"Installing an Expansion Card."
6
7
Close the system. See "Closing the System."
Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
If the problem is not resolved, proceed to step 8.
8
9
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
Open the system. See "Opening the System."
Troubleshooting Your System
161
10 Remove all expansion cards installed in the system. See "Removing an
Expansion Card."
11 Reseat the expansion-card risers to the system board. See "Expansion
Cards and Expansion-Card Risers."
12 Close the system. See "Closing the System."
13 Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
14 Run the appropriate online diagnostic test.
If the tests fail, see "Getting Help."
15 For each expansion card you removed in step 10, perform the following
steps:
a
Turn off the system and attached peripherals, and disconnect the
system from the electrical outlet.
b
c
d
e
Open the system. See "Opening the System."
Reinstall one of the expansion cards.
Close the system. See "Closing the System."
Run the appropriate diagnostic test.
If the tests fail, see "Getting Help."
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
2
Run the appropriate online diagnostics test. See "Using Dell Online
Diagnostics."
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
3
4
Open the system. See "Opening the System."
Remove the cooling shroud. See "Removing the Cooling Shroud."
162
Troubleshooting Your System
5
Ensure that each processor and heat sink are properly installed. See
"Installing a Processor."
6
7
8
Replace the cooling shroud. See "Installing the Cooling Shroud."
Close the system. See "Closing the System."
Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
9
Run the appropriate online diagnostic test.
If your system only has one processor and a problem is still indicated, see
"Getting Help."
10 For systems with multiple processors, turn off the system and attached
peripherals, and disconnect the system from the electrical outlet.
11 Open the system. See "Opening the System"
12 Remove the cooling shroud. See "Removing the Cooling Shroud."
CAUTION: Be careful not to bend any of the pins on the ZIF socket when removing
the processor. Bending the pins can permanently damage the system board.
13 Remove processor 2. See "Removing a Processor."
14 Replace the cooling shroud. See "Installing the Cooling Shroud."
15 Close the system. See "Closing the System."
16 Reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
17 Run the appropriate online diagnostic test.
If the test fails, the processor is faulty. See "Getting Help."
18 Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
19 Open the system. See "Opening the System."
20 Remove the cooling shroud. See "Removing the Cooling Shroud."
21 Replace the processor with the processor you removed in step 13. See
"Installing a Processor."
22 Replace the cooling shroud. See "Installing the Cooling Shroud."
23 Repeat step 15 through step 17.
If the problem persists, the system board is faulty. See "Getting Help."
Troubleshooting Your System
163
164
Troubleshooting Your System
Running the System Diagnostics
If you experience a problem with your system, run the diagnostics before
calling for technical assistance. The purpose of the diagnostics is to test your
system's hardware without requiring additional equipment or risking data
loss. If you are unable to fix the problem yourself, service and support
personnel can use diagnostics test results to help you solve the problem.
Using Dell Online Diagnostics
To assess a system problem, first use the Dell™ Online Diagnostics. Dell
Online Diagnostics is a suite of diagnostic programs, or test modules, that
include diagnostic tests on chassis and storage components such as hard
drives, physical memory, communications and printer ports, NICs, CMOS,
and more. If you are unable to identify the problem using the Dell Online
Diagnostics, then use the embedded system diagnostics.
The files required to run Online Diagnostics for systems running supported
®
®
Microsoft Windows and Linux operating systems are available at
support.dell.com and on the DVDs that came with your system. For
information about using diagnostics, see the Dell Online Diagnostics User's
Guide.
The embedded system diagnostics can be launched using Unified Server
Configurator (USC). For more information about using USC, see the Unified
Server Configurator documentation on the Dell Support website at
support.dell.com/manuals.
Embedded System Diagnostics Features
The embedded system diagnostics provides a series of menus and options for
particular device groups or devices. The system diagnostics menus and
options allow you to:
•
•
•
Run tests individually or collectively
Control the sequence of tests
Repeat tests
Running the System Diagnostics
165
•
•
Display, print, or save test results
Temporarily suspend testing if an error is detected or terminate testing
when a user-defined error limit is reached
•
•
•
View help messages that briefly describe each test and its parameters
View status messages that inform you if tests are completed successfully
View error messages that inform you of problems encountered
during testing
When to Use the Embedded System Diagnostics
If a major component or device in the system does not operate properly,
component failure may be indicated. As long as the processor and the
system's input/output devices are functioning, you can use the system
diagnostics to help identify the problem.
Running the Embedded System Diagnostics
You can run the embedded system diagnostics program from the USC main
screen.
CAUTION: Use the system diagnostics to test only your system. Using this
program with other systems may cause invalid results or error messages.
1
2
As the system boots, press <F10> to start the USC.
Click Diagnostics in the left pane and click Launch Diagnostics in the
right pane.
The Diagnostics menu allows you to run all or specific diagnostics tests or
to exit.
166
Running the System Diagnostics
Embedded System Diagnostics Testing Options
Click the testing option in the Main Menu window.
Testing Option
Function
Express Test
Performs a quick check of the system. This option runs
device tests that do not require user interaction.
Extended Test
Performs a more thorough check of the system. This test
can take an hour or longer.
Custom Test
Information
Tests a particular device.
Displays test results.
Using the Custom Test Options
When you select Custom Test in the Main Menu window, the Customize
window allows you to select the device(s) to be tested, select specific options
for testing, and view the test results.
Selecting Devices for Testing
The left side of the Customize window lists devices that can be tested. Click
the (+) next to a device or module to view its components. Click (+) on any
component to view the tests that are available. Clicking a device, rather than
its components, selects all of the components of the device for testing.
NOTE: After you select all the devices and components that you want to test,
highlight All Devices and then click Run Tests.
Selecting Diagnostics Options
From the Diagnostics Options area, select the test(s) you want to run on a
device:
•
Non-Interactive Tests Only — Runs only tests that require no user
intervention.
•
•
Quick Tests Only — Runs only the quick tests on the device.
Show Ending Timestamp — Time stamps the test log.
Running the System Diagnostics
167
•
•
Test Iterations — Selects the number of times the test is run.
Log output file pathname — Enables you to specify the diskette drive or
USB memory key where the test log file is saved. You cannot save the file to
a hard drive.
Viewing Information and Results
The following tabs in the Customize window provide information about the
test and the test results:
•
•
•
Results — Displays the test that ran and the result.
Errors — Displays any errors that occurred during the test.
Help — Displays information about the currently selected device,
component, or test.
•
•
Configuration — Displays basic configuration information about the
currently selected device.
Parameters — Displays parameters that you can set for the test.
168
Running the System Diagnostics
Jumpers and Connectors
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
System Board Jumpers
For information on resetting the password jumper to disable a password, see
"Disabling a Forgotten Password."
Jumpers and Connectors
169
Figure 6-1. System Board Jumpers
Jumper
Setting
Description
PWRD_EN
Pins 2 and
4(default)
The password feature is enabled.
Pins 4 and 6 The password feature is disabled and
iDRAC6 local access is unlocked at the next
AC power cycle.
NVRAM_CLR
Pins 3 and 5 The configuration settings are retained at
(default)
system boot.
170
Jumpers and Connectors
Jumper
Setting
Description
Pins 1 and 3 The configuration settings are cleared at the
next system boot. If the configuration
settings become corrupted to the point
where the system will not boot, install the
jumper and boot the system. Remove the
jumper before restoring the configuration
information.
Jumpers and Connectors
171
Connector
iDRAC6
SATA_A
SATA_B
Description
3
4
5
6
iDRAC6 Enterprise card connector
SATA A connector
SATA B connector
B1
B4
B7
B2
B5
B8
B3
B6
B9
memory module slot B1(white release lever)
memory module slot B4
memory module slot B7
memory module slot B2(white release lever)
memory module slot B5
memory module slot B8
memory module slot B3(white release lever)
memory module slot B6
memory module slot B9
7
8
9
FAN5
System cooling fan
BP_PWR
CPU2
Backplane power connector
Processor 2
10 FAN4
System cooling fan
11 BATTERY
12 DVD/TBU_PWR
13 FAN3
System battery
Power connector for optical drive and tape backup unit
System cooling fan
14 CPU1
Processor 1
15 CTRL_USB
16 FAN2
Control panel USB interface connector
System cooling fan
17 CTRL_PNL
18 FAN1
Control panel interface connector
System cooling fan
Jumpers and Connectors
173
Connector
19 A1
Description
memory module slot A1(white release lever)
memory module slot A4
A4
A7
A2
A5
A8
A3
A6
A9
memory module slot A7
memory module slot A2(white release lever)
memory module slot A5
memory module slot A8
memory module slot A3(white release lever)
memory module slot A6
memory module slot A9
20 PWR2
Power supply connector for PS2
Power supply connector for PS1
NIC hardware key
21 PWR1
22 ISCSI_KEY
174
Jumpers and Connectors
SAS Backplane Board Connectors
Figure 6-3. SAS Backplane Board (6 Slots)
1
2
3
4
5
6
front
9
8
7
back
1
3
5
7
9
drive 1 connector
drive 3 connector
drive 5 connector
2
4
6
8
drive 0 connector
drive 2 connector
drive 4 connector
SAS A connector
backplane power (BP_PWR)
SAS B connector
Jumpers and Connectors
175
Expansion-Card Riser-Board Components and
PCIe Buses
Figure 6-4. PCIe Expansion-Card Riser 1 Components
1
2
3
4
5
1
slot 1 PCIe - x4 link (full-height, 30.99-
cm [12.2-in] length)
2
4
slot 2 PCIe - x4 link (low profile, 24.13-
cm [9.5-in] length)
3
5
storage controller socket
release button
card edge connector
176
Jumpers and Connectors
Figure 6-6. Optional PCIe x16 Expansion-Card Riser 2 Components
1
3
2
4
5
1
3
chassis intrusion switch
2
plunger
cm [9.5-in] length)
5
card edge connector
Disabling a Forgotten Password
The system's software security features include a system password and a setup
password, which are discussed in detail in "Using the System Setup Program
and UEFI Boot Manager." The password jumper enables these password
features or disables them and clears any password(s) currently in use.
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
3
Open the system. See "Opening the System."
Move the password jumper plug to the disabled position (pins 4 and 6).
178
Jumpers and Connectors
See Figure 6-1 to locate the password jumper (labeled "PWRD_EN") on
the system board.
4
5
Close the system. See "Closing the System."
Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
The existing passwords are not disabled (erased) until the system boots
with the password jumper plug in the disabled position. However, before
you assign a new system and/or setup password, you must reset the jumper
plug to the enabled position.
still in the disabled position, the system disables the new password(s) the next
time it boots.
6
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
7
8
9
Open the system. See "Opening the System."
Move the password jumper plug to the enabled position (pins 2 and 4).
Close the system. See "Closing the System."
10 Reconnect your system and peripherals to their electrical outlets, and turn
on the system.
11 Assign a new system and/or setup password.
To assign a new password using the System Setup program, see "Assigning
a System Password."
Jumpers and Connectors
179
180
Jumpers and Connectors
Getting Help
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options.
Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or
customer service issues:
1
2
Visit support.dell.com.
Verify your country or region in the Choose A Country/Region drop-down
menu at the bottom of the page.
3
4
Click Contact Us on the left side of the page.
Select the appropriate service or support link based on your need.
Choose the method of contacting Dell that is convenient for you.
Getting Help
181
182
Getting Help
Glossary
A — Ampere(s).
AC — Alternating current.
ACPI — Advanced Configuration and Power Interface. A standard interface for
enabling the operating system to direct configuration and power management.
ambient temperature — The temperature of the area or room where the system is
located.
ANSI — American National Standards Institute. The primary organization for
developing technology standards in the U.S.
asset tag — An individual code assigned to a system, usually by an administrator, for
security or tracking purposes.
backup — A copy of a program or data file. As a precaution, back up your system’s
hard drive(s) on a regular basis.
blade — A module that contains a processor, memory, and a hard drive. The modules
are mounted into a chassis that includes power supplies and fans.
bootable media — A diskette, USB memory key, or optical media that is used to start
your system in lieu of the hard drives.
BTU — British thermal unit.
bus — An information pathway between the components of a system. Your system
contains an expansion bus that allows the processor to communicate with controllers
for the peripheral devices connected to the system. Your system also contains an
address bus and a data bus for communications between the processor and RAM.
C — Celsius.
cache — A fast storage area that keeps a copy of data or instructions for quick data
retrieval.
cm — Centimeter(s).
COMn — The device names for the serial ports on your system. Serial ports can be
either physical or virtual.
control panel — The part of the system that contains indicators and controls, such as
the power button and power indicator.
controller — A chip or expansion card that controls the transfer of data between the
processor and memory or between the processor and a peripheral device.
coprocessor — A chip that relieves the system’s processor of specific processing tasks.
A math coprocessor, for example, handles numeric processing.
Glossary
183
CPU — Central processing unit. See processor.
DC — Direct current.
DDR — Double-data rate. A technology in memory modules that potentially doubles
the data rate by transferring data on both the rising and falling pulses of a clock cycle.
device driver — A program that allows the operating system or some other program to
interface correctly with a peripheral.
DHCP — Dynamic Host Configuration Protocol. A method of automatically
assigning an IP address to a client system.
diagnostics — A comprehensive set of tests for your system.
DIMM — Dual in-line memory module. See also memory module.
DNS — Domain Name System. A method of translating Internet domain names, such
as www.example.com, into IP addresses, such as 208.77.188.166.
DRAM — Dynamic random-access memory. A system’s RAM is usually made up
entirely of DRAM chips.
driver — See device driver.
DVD — Digital versatile disc or digital video disc.
ECC — Error checking and correction.
EMI — Electromagnetic interference.
ESD — Electrostatic discharge.
ESM — Embedded server management. See iDRAC.
expansion bus — Your system contains an expansion bus that allows the processor to
communicate with controllers for peripherals, such as NICs.
expansion card — An add-in card, such as a NIC or SCSI adapter, that plugs into an
expansion-card connector on the system board. An expansion card adds some
specialized function to the system by providing an interface between the expansion
bus and a peripheral.
expansion-card connector — A connector on the system board or riser board for
plugging in an expansion card.
F — Fahrenheit.
FAT — File allocation table. The file system structure used by MS-DOS to organize
®
®
and keep track of file storage. The Microsoft Windows operating systems can
optionally use a FAT file system structure.
Fibre Channel — A high-speed network interface used primarily with networked
storage devices.
184
Glossary
flash memory — A type of electronic chip that can be programmed and
reprogrammed using a software utility.
FTP — File transfer protocol.
g — Gram(s).
G — Gravities.
Gb — Gigabit(s); 1024 megabits or 1,073,741,824 bits.
GB — Gigabyte(s); 1024 megabytes or 1,073,741,824 bytes. However, when referring
to hard-drive capacity, the term is usually rounded to 1,000,000,000 bytes.
graphics mode — A video mode that can be defined as x horizontal by y vertical pixels
by z colors.
host adapter — A controller that implements communication between the system’s
bus and the peripheral device, typically a storage device.
hot-swap — The ability to insert or install a device, typically a hard drive or an internal
cooling fan, into the host system while the system is powered on and running.
Hz — Hertz.
I/O — Input/output. A keyboard is an input device, and a monitor is an output device.
In general, I/O activity can be differentiated from computational activity.
iDRAC iDRAC6 — Integrated Dell Remote Access Controller. A systems management
,
hardware and software solution that provides remote management capabilities, crashed
system recovery, and power control functions for Dell PowerVault systems.
IP — Internet Protocol.
IPv6 — Internet Protocol version 6.
IPX — Internet package exchange.
IRQ — Interrupt request. A signal that data is about to be sent to or received by a
peripheral device travels by an IRQ line to the processor. Each peripheral connection
must be assigned an IRQ number. Two devices can share the same IRQ assignment,
but you cannot operate both devices simultaneously.
iSCSI — Internet SCSI (see SCSI). A protocol that enables SCSI device
communication across a network or the Internet.
jumper — Small blocks on a circuit board with two or more pins emerging from them.
Plastic plugs containing a wire fit down over the pins. The wire connects the pins and
creates a circuit, providing a simple and reversible method of changing the circuitry in
a board.
K — Kilo-; 1000.
Kb — Kilobit(s); 1024 bits.
Glossary
185
KB — Kilobyte(s); 1024 bytes.
Kbps — Kilobit(s) per second.
KBps — Kilobyte(s) per second.
kg — Kilogram(s); 1000 grams.
kHz — Kilohertz.
KVM — Keyboard/video/mouse. KVM refers to a switch that allows selection of the
system from which the video is displayed and for which the keyboard and mouse are
used.
LAN — Local area network. A LAN is usually confined to the same building or a few
nearby buildings, with all equipment linked by wiring dedicated specifically to the
LAN.
LCD — Liquid crystal display.
LED — Light-emitting diode. An electronic device that lights up when a current is
passed through it.
local bus — On a system with local-bus expansion capability, certain peripheral
devices (such as the video adapter circuitry) can be designed to run much faster than
they would with a traditional expansion bus. See also bus.
LOM — LAN on motherboard. Also referred to as embedded NIC.
LVD — Low voltage differential.
m — Meter(s).
mA — Milliampere(s).
MAC address — Media Access Control address. Each network device’s unique
hardware number on a network.
mAh — Milliampere-hour(s).
Mb — Megabit(s); 1,048,576 bits.
MB — Megabyte(s); 1,048,576 bytes. However, when referring to hard-drive capacity,
the term is often rounded to mean 1,000,000 bytes.
Mbps — Megabits per second.
MBps — Megabytes per second.
MBR — Master boot record.
memory address — A specific location, usually expressed as a hexadecimal number, in
the system’s RAM.
memory module — A small circuit board containing DRAM chips that connects to the
system board.
186
Glossary
memory — An area in your system that stores basic system data. A system can contain
several different forms of memory, such as integrated memory (ROM and RAM) and
add-in memory modules (DIMMs).
memory key — A portable flash memory storage device integrated with a USB
connector.
MHz — Megahertz.
mirroring — A type of data redundancy applicable to hard drives or system memory.
When applied to hard drives, a set of physical drives stores data and one or more sets
of additional drives stores duplicate copies of the data. Mirroring functionality is
provided by software. See also striping and RAID. When applied to system memory,
data in one set of memory modules is duplicated in an identical set of memory
modules.
mm — Millimeter(s).
ms — Millisecond(s).
NAS — Network Attached Storage. NAS is one of the concepts used for implementing
shared storage on a network. NAS systems have their own operating systems,
integrated hardware, and software that are optimized to serve specific storage needs.
NIC — Network interface controller. A device that is installed or integrated in a
system to allow connection to a network.
NMI — Nonmaskable interrupt. A device sends an NMI to signal the processor about
hardware errors.
ns — Nanosecond(s).
NVRAM — Nonvolatile random-access memory. Memory that does not lose its
contents when you turn off your system. NVRAM is used for maintaining the date,
time, and system configuration information.
parity — Redundant information that is associated with a block of data.
parity stripe — In RAID arrays, the parity-striped hard drive of a set of striped hard
drives contains parity data that enable data recovery in the event that one of the other
hard drives fails.
partition — You can divide a hard drive into multiple physical sections called
partitions with the fdisk command. Each partition can contain multiple logical drives.
You must format each logical drive with the format command.
PCI — Peripheral Component Interconnect. A standard for local-bus
implementation.
PCIe — PCI Express. An improved PCI expansion bus technology that uses one or
multiple full-duplex serial data lines to interface between the CPU and the expansion
card and which greatly increases data bandwidth.
Glossary
187
PDU — Power distribution unit. A power source with multiple power outlets that
provides electrical power to servers and storage systems in a rack.
peripheral — An internal or external device, such as a diskette drive or keyboard,
connected to a system.
pixel — A single point on a video display. Pixels are arranged in rows and columns to
create an image. A video resolution, such as 640 x 480, is expressed as the number of
pixels across by the number of pixels up and down.
POST — Power-on self-test. Before the operating system loads when you turn on your
system, the POST tests various system components such as RAM and hard drives.
processor — The primary computational chip inside the system that controls the
interpretation and execution of arithmetic and logic functions. Software written for
one processor must usually be revised to run on another processor. CPU is a synonym
for processor.
PSU — Power supply unit.
PXE — Preboot eXecution Environment. A way of booting a system via a LAN
(without a hard drive or bootable diskette).
QPI— QuickPath Interconnect. The bus interface between the processors and
between the processors and the IOH chip.
RAID — Redundant array of independent disks. A method of providing data
redundancy. Some common implementations of RAID include RAID 0, RAID 1, RAID
5, RAID 10, RAID 50, and RAID 60. See also mirroring and striping.
RAM — Random-access memory. The system’s primary temporary storage area for
program instructions and data. Any information stored in RAM is lost when you turn
off your system.
RDIMM — A registered DDR3 memory module.
readme file — A text file, usually shipped with software or hardware, that contains
information supplementing or updating the product’s documentation.
read-only file — A read-only file is one that you are prohibited from editing or
deleting.
ROM — Read-only memory. Your system contains some programs essential to its
operation in ROM code. A ROM chip retains its contents even after you turn off your
system. Examples of code in ROM include the program that initiates your system’s
boot routine and the POST.
ROMB — RAID on motherboard.
SAN — Storage Area Network. A network architecture that enables remote network-
attached storage devices to appear to a server to be locally attached.
188
Glossary
SAS — Serial-attached SCSI.
SATA — Serial Advanced Technology Attachment. A standard interface between the
system board and storage devices.
SCSI — Small computer system interface. An I/O bus interface.
SD card — Secure digital flash memory card.
SDDC — Single device data correction.
SDRAM — Synchronous dynamic random-access memory.
sec — Second(s).
serial port — A legacy I/O port with a 9-pin connector that transfers data one bit at a
time and is most often used to connect a modem to the system.
service tag — A bar code label on the system used to identify it when you call Dell for
technical support.
SMART — Self-Monitoring Analysis and Reporting Technology. Allows hard drives to
report errors and failures to the system BIOS and then display an error message on the
screen.
SMP — Symmetric multiprocessing. Used to describe a system that has two or more
processors connected via a high-bandwidth link and managed by an operating system,
where each processor has equal access to I/O devices.
SNMP — Simple Network Management Protocol. A standard interface that allows a
network manager to remotely monitor and manage workstations.
SSD — Solid State Drives.
striping — Disk striping writes data across three or more disks in an array, but only
uses a portion of the space on each disk. The amount of space used by a "stripe" is the
same on each disk used. A virtual disk may use several stripes on the same set of disks
in an array. See also guarding, mirroring, and RAID.
system board — As the main circuit board, the system board usually contains most of
your system’s integral components, such as the processor(s), RAM, controllers for
peripherals, and various ROM chips.
system configuration information — Data stored in memory that tells a system what
hardware is installed and how the system should be configured for operation.
system memory — See RAM.
System Setup program — A BIOS-based program that allows you to configure your
system’s hardware and customize the system’s operation by setting features such as
password protection. Because the System Setup program is stored in NVRAM, any
settings remain in effect until you change them again.
Glossary
189
TB — Terabyte(s); 1024 gigabytes or 1,099,511,627,776 bytes. However, when
referring to hard-drive capacity, the term is usually rounded to 1,000,000,000,000
bytes.
TCP/IP — Transmission Control Protocol/Internet Protocol.
termination — Some devices (such as the last device at each end of a SCSI cable)
must be terminated to prevent reflections and spurious signals in the cable. When
such devices are connected in a series, you may need to enable or disable the
termination on these devices by changing jumper or switch settings on the devices or
by changing settings in the configuration software for the devices.
TOE — TCP/IP offload engine. A technology that offloads network processing to the
network controller.
UDIMM — An unregistered (unbuffered) DDR3 memory module.
UEFI — Unified Extensible Firmware Interface.
uplink port — A port on a network hub or switch used to connect to other hubs or
switches without requiring a crossover cable.
UPS — Uninterruptible power supply. A battery-powered unit that automatically
supplies power to your system in the event of an electrical failure.
USB — Universal Serial Bus. A USB connector provides a single connection point for
multiple USB-compliant devices, such as mice and keyboards. USB devices can be
connected and disconnected while the system is running.
USB memory key — See memory key.
utility — A program used to manage system resources—memory, disk drives, or
printers, for example.
V — Volt(s).
VAC — Volt(s) alternating current.
VDC — Volt(s) direct current.
video adapter — The logical circuitry that provides (in combination with the monitor)
your system’s video capabilities. A video adapter may be integrated into the system
board or may be an expansion card that plugs into an expansion slot.
video memory — Most VGA and SVGA video adapters include memory chips in
addition to your system’s RAM. The amount of video memory installed primarily
influences the number of colors that a program can display (with the appropriate video
drivers and monitor capabilities).
video resolution — Video resolution (800 x 600, for example) is expressed as the
number of pixels across by the number of pixels up and down. To display a program at
190
Glossary
a specific graphics resolution, you must install the appropriate video drivers and your
monitor must support the resolution.
virtualization — The ability via software to share the resources of a single computer
across multiple environments. A single physical system may appear to the user as
multiple virtual systems able to host multiple operating systems.
W — Watt(s).
WH — Watt-hour(s).
XML — Extensible Markup Language. XML is a way to create common information
formats and to share both the format and the data on the World Wide Web, intranets,
and elsewhere.
ZIF — Zero insertion force.
Glossary
191
192
Glossary
Index
cable routing, 111
optical drive, 102
A
Advanced ECC memory
mode, 124
storage controller, 108
connectors
expansion-card riser 1, 176
expansion-card riser 2, 177-178
NIC, 19
B
back panel features, 18
backplane
See SAS backplane.
system board, 172
USB, 12
battery (RAID)
installing, 109
removing, 109
video, 12
contacting Dell, 181
battery (system)
replacing, 136
control panel assembly
features, 12
troubleshooting, 152
LCD panel features, 14
BIOS boot mode, 55
control panel board
installing, 140
blank
removing, 139
hard drive, 81
power supply, 87
installing, 138
boot mode, 55
removing, 138
cooling fan
removing, 99
C
replacing, 100
troubleshooting, 154
cable retention bracket
installing, 112
cooling shroud
removing, 111
installing cooling shroud, 98
removing, 97
cable routing, 111
cabling
Index
193
cover
closing, 78
opening, 78
removing, 116
connectors, 177-178
installing, 119
D
installing into expansion-card
bracket, 121
damaged systems
removing, 118
troubleshooting, 151
removing from expansion-card
bracket, 120
Dell
contacting, 181
diagnostics
testing options, 167
using Online Diagnostics, 165
when to use, 166
fan
removing, 99
replacing, 100
DIMMs
fan brackets
removing, 100
replacing, 102
See memory modules (DIMMs).
drive blank
installing, 81
removing, 81
front panel features, 12
drive carrier
hard drive, 83
G
DVD drive
guidelines
See optical drive.
expansion card installation, 112
E
error messages, 56
H
expansion cards
hard drive
See PCIe expansion cards.
drive carrier, 83
installing, 82
removing, 82
expansion-card riser 1
connectors, 176
194
Index
heat sink, 131
RAID battery, 109
riser 2 into expansion-card
bracket, 121
hot-swap
cooling fans, 99
hard drives, 80
power supplies, 85
SAS backplane board, 142
SD card, 89
storage controller, 106
VFlash SD card, 95
Integrated Dell Remote Access
Controller
I
See iDRAC6 Enterprise card.
iDRAC6 Enterprise card
installing, 93
integrated storage controller
See storage controller.
removing, 94
internal SD flash card
installing, 89
indicators
back panel, 18
front panel, 12
NIC, 21
power, 12, 20
internal USB memory key, 90
troubleshooting, 157
installing
cable retention bracket, 112
control panel board, 140
control panel display module, 138
cooling shroud, 98
expansion-card riser 1, 117
hard drive blank, 81
jumpers (system board), 169
hard drives, 82
iDRAC6 Enterprise card, 93
internal SD flash card, 89
internal SD module, 87
internal USB memory key, 90
memory modules, 127
optical drive, 102
keyboard
troubleshooting, 148
L
PCIe expansion cards, 113
power supply blank, 87
processor, 133
LAN-on-motherboard (LOM)
See NICs.
Index
195
LCD panel
features, 14
menus, 15
hardware key, 95
indicators, 21
troubleshooting, 149
M
O
memory
troubleshooting, 154
Online Diagnostics
using, 165
mode, 124
memory mode
troubleshooting, 158
Advanced ECC, 124
Memory Mirroring, 124
Optimizer, 124
memory modules (DIMMs)
configuring, 122
installing, 127
RDIMM configurations, 125
removing, 129
password
disabling, 178
setup, 72
UDIMM configurations, 113,
127
system, 70
messages
PCIe expansion cards
installing, 113
error messages, 56
status LCD, 22
system, 36
removing, 115
troubleshooting, 161
warning, 52
microprocessor
POST
See processor.
accessing system features, 11
power indicators, 12, 20
power supplies
indicators, 20
removing, 85
replacing, 86
N
NIC hardware key, 95
NICs
196
Index
troubleshooting, 152
power supply, 85
power supply blank, 87
processor, 130
power supply blank, 87
processor
RAID battery, 109
riser 2 from bracket, 120
SAS backplane board, 141
SD card, 90
installing, 133
removing, 130
troubleshooting, 162
upgrades, 130
PSU
replacing
See power supply.
cooling fan, 100
R
RAID battery
installing, 109
removing, 109
removing
cable retention bracket, 111
control panel board, 139
control panel display module, 138
cooling fan, 99
safety, 147
cooling shroud, 97
expansion-card riser 1, 116
expansion-card riser 2, 118
fan brackets, 100
SAS controller
hard drive blank, 81
See storage controller.
hard drive from a drive carrier, 83
hard drives, 82
SD card
iDRAC6 Enterprise card, 94
integrated storage controller, 106
internal SD flash card, 89
internal SD module, 89
memory modules, 129
optical drive, 102
installing, 89
removing, 90
troubleshooting, 156
SD card (VFlash)
installing, 95
securing your system, 66, 71
PCIe expansion cards, 115
Index
197
serial connector, 20
main screen, 57
service-only procedures
control panel assembly, 138
SAS backplane, 141
memory settings, 59
PCI IRQ assignments, 63
system board, 143
setup password, 72
SSD hard drives, 80
options, 63
startup
system security options, 66
system startup failure, 147
storage controller
cabling, 108
installing, 106
T
removing, 106
troubleshooting, 160
TPM security, 66
support
troubleshooting
cooling fans, 154
contacting Dell, 181
damaged system, 151
internal USB memory key, 157
keyboard, 148
system board
connectors, 172
installing, 145
jumpers, 169
removing, 143
memory, 154
NIC, 149
system cooling
PCIe expansion cards, 161
power supplies, 152
SD card, 156
troubleshooting, 153
system features
accessing, 11
system messages, 36
system password, 70
storage controller, 160
system battery, 152
system cooling, 153
system startup failure, 147
video, 148
system setup program
boot settings, 61
embedded server management
options, 64
wet system, 150
integrated devices options, 62
198
Index
U
UEFI Boot Manager
entering, 68
main screen, 69
System Utilities screen, 69
UEFI Boot Settings screen, 69
UEFI boot mode, 55
upgrades
processor, 130
USB
back-panel connectors, 19
front panel connectors, 12
USB memory key
See internal USB memory key.
V
VFlash media, 95
video
front panel connectors, 12
troubleshooting, 148
W
warning messages, 52
warranty, 53
wet system
troubleshooting, 150
Index
199
200
Index
|