De’Longhi America, Inc.
Park 80 West, Plaza One
Saddle Brook, NJ 07663
1-866-528-8323 (1-866-Latte-Best)
De’Longhi Canada, Inc.
6150 McLaughlin Road
Mississauga, Ontario
L5R 4E1 Canada
1-888-335-6644
Fiducia Italiana S.A de C.V.
Pestalozzi 814
Col. Del Valle
Del. Benito Juarez
México D.F. 03100
tels: 5543 1447 y 5543 6492
Lada sin costo: 01800 711 8805
5713212301/07.09
2
A
B
A4 A5
A3
B1
B3
A6
B6
A2
A1
A7
A8
A9
B5
B4
A22
B2
A10
A21
A20
A19
A11
A12
A23
A24
A13
A14
A15
A18
A17
A16
C
C15
C16
C1
C2
C3
Ready
espresso
C14
C13
C12
C4
C5
C6
C11
C10
C9
C8
C7
3
1
2
3
7
5
6
4
8
9
10
11
15
13
14
12
4
normal coffee
16
17
18
19
M
A
X
20
21
22
23
27
24
25
26
29
30
31
28
5
33
34
32
35
36
38
39
37
40
41
hot WAtEr.....................................17
Preparation ....................................................17
Changing the quantity....................................17
InDEx
ImportAnt SAFEGuArDS.................... 8
Short CorD InStruCtIonS ................ 8
CLEAnInG.......................................17
Cleaning the coffee maker..............................17
Cleaning the coffee grounds container...........17
Cleaning the drip tray.....................................18
Cleaning the water tank..................................18
Cleaning the coffee nozzles............................18
Cleaning the pre-ground coffee feed funnel ...18
Cleaning the inside of the machine ................18
Cleaning the brew group................................18
Cleaning the milk container............................19
IntroDuCtIon ................................. 9
Symbols used in these instructions.................9
Letters in brackets ...........................................9
Troubleshooting and repairs ............................9
DESCrIptIon.................................... 9
Description of appliance ..................................9
Description of milk container...........................9
Description of control panel (touch screen).....9
DESCALInG .....................................19
prELImInAry ChECKS .......................10
Controls after transport..................................10
Installing the appliance ..................................10
Connecting the appliance...............................10
Setting up the appliance.................................11
SEttInG WAtEr hArDnESS.................20
Measuring water hardness.............................20
Setting water hardness ..................................20
uSInG CompArtmEnt For LAttE GLASS 20
DISpLAyED mESSAGES.......................21
trouBLEShootInG...........................22
LImItED WArrAnty..........................24
turnInG thE AppLIAnCE on ...............11
turnInG thE AppLIAnCE oFF .............11
ChAnGInG thE mEnu SEttInGS ...........12
Setting the language .....................................12
Setting the clock ............................................12
Setting auto-start time...................................12
Setting the temperature .................................12
Setting auto-off..............................................12
Resetting default values (reset) .....................13
Statistics function..........................................13
Acoustic signal (Beep enabled)......................13
mAKInG CoFFEE ..............................13
Selecting the coffee taste...............................13
Selecting the quantity of coffee in the cup .....13
ESPRESSO (oz) .............................................13
LONG COFFEE (oz).........................................13
Programming the espresso “my coffee”
quantity..........................................................13
Programming the long “my coffee” quantity..14
Regulating the coffee mill ..............................14
Making espresso coffee using coffee beans...14
Making long coffee using coffee beans..........14
Making espresso or long coffee using
pre-ground coffee..........................................15
mAKInG DrInKS WIth mILK ................15
Filling and attaching the milk container..........15
Making latte ..................................................15
Making cappuccino........................................16
Making Italian macchiato...............................16
Making hot milk.............................................16
Cleaning the milk container after use.............16
Programming the size for each beverage
button ............................................................16
7
I m p o r t A n t S A F E G u A r D S
When using electrical appliances, basic safety precautions should always be followed, inclu-
ding the following.
•
•
Read all instructions carefully.
Make sure the voltage of your electrical system corresponds to the voltage shown on the
bottom of the machine.
Do not touch hot surfaces. Use handles or knobs.
To protect against fire, electrical shock and personal injury, do not immerse cord, plug or
appliance in water or other liquid.
Keep the appliance out of the reach of children and do not leave appliance unattended
while in operation.
•
•
•
•
•
Unplug from the outlet when not in use and before cleaning.
Do not operate with a damaged cord or plug, or after the appliance malfunctions, or has
been damaged in any manner. Return the appliance to the nearest authorized service
facility for examination, repair or adjustment.
The use of accessory attachments not recommended by the manufacturer may result in
fire, electrical shock, or personal injury.
Do not use outdoors.
•
•
•
Make sure the power cord does not hang over the edge of the table or counter-top to avoid
getting accidentally caught or entangled.
•
•
•
Do not place the appliance or its electrical parts on or near electric stoves, cooking surfa-
ces, or gas burners.
Plug cord into the wall outlet. To disconnect, first turn machine “off”, then remove plug
from wall outlet.
Do not use the appliance for other than the intended use. This appliance is to be utilized
for domestic use only. The manufacturer declines all responsibility for any damage caused
by improper, incorrect, or irresponsible use.
WArnInG: to reduce the risk of fire or electric shock, do not remove the cover or the exterior of the
unit. Don’t attempt to repair or modify the machine, doing so will void the warranty. repair should
be done by authorized service personnel only!
SAVE thESE InStruCtIonS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
Short CorD InStruCtIonS
A short power cord is provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
Longer, detachable power supply cords or extension cords are available and may be used if care is
exercised in their use.
If an extension cord is used, the marked electrical rating should be at least as great as the electrical
rating of the appliance. If the appliance is provided with 3- wire, grounding type cord, the extension
should be a GROUNDING TYPE 3 - WIRE CORD. The longer cord should be arranged so that it will
not drape over the counter-top or table top where it can be pulled on by children or tripped over.
Your product is equipped with a polarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
-
-
-
8
IntroDuCtIon
DESCrIptIon
Description of appliance
(page 3 - A )
A1. Grinding coarseness regulator knob
A2. Container for coffee beans
A3. Main switch (some models only)
A4. Bean container lid
ThankyouforchoosingtheESAM6700automatic
coffee and cappuccino maker.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the
machine.
A5. Cover for pre-ground coffee funnel
A6. Measuring scoop compartment
A7. Cup warmer shelf
A8. Ground coffee funnel
A9. Display
Symbols used in these instructions
Important warnings are identified by these
symbols.
These warnings must absolutely be respected.
A10. Touch screen (control panel)
A11. Hot water and steam nozzle
A12. Brew group
A13. Water tank
A14. Power cable
Danger!
Failure to observe the warning could result in
possibly life threatening injury from electric
shock.
A15. Cup tray
A16. Drip tray
A17. Compartment for latte glass
A18. Grounds tray
Important!
Failure to observe the warning could result in
injury or damage to the appliance.
A19. Service door
Danger Of burns!
A20. Coffee spout (adjustable height)
A21. Coffee guide
A22. ON/STAND-BY button
A23. Hot water spout
Failure to observe the warning could result in
scalds or burns.
Information :
This symbol identifies important advice or
information for the user. .
A24. Coffee scoop
Description of milk container
(page 3 - B )
B1. Milk frother selector
B2. Milk container handle
B3. CLEAN button
B4. Milk intake tube
B5. Frothed milk spout
B6. Lid for milk frother
Letters in brackets
The letters in brackets refer to the legend in the
description of the appliance on page 3.
troubleshooting and repairs
In the event of problems, first try and resolve
them following the information given in the
sections “Displayed messages” on page 21 and
“Troubleshooting” on page 23.
Description of control panel (touch screen)
If this does not resolve the problem or you
require further information, you should consult
Customer Service by calling the number given on
the “Customer Service” sheet.
If your country is not among those listed on the
sheet, call the number given in the guarantee.
If repairs are required, contact De’Longhi
customer services only.
(page 3 - C )
Information: Only the icons relating to
the controls enabled for the particular function
currently being used will be lit on the touch
screen.
C1. Display: guides the user in using the
appliance.
C2. : icon: to scroll forwards through the
programming menu.
The addresses are given in the warranty
certificate provided with the machine.
C3.
icon: to deliver one cup of espresso
coffee.
icon: to deliver one cup of espresso
C4.
9
coffee.
prELImInAry ChECKS
Controls after transport
After removing the packaging, make sure the
product is complete and undamaged and that all
accessories are present.
Do not use the appliance if it is visibly damaged.
Contact Customer Service.
C5. oK icon: to enable and confirm the selected
function.
C6.
icon: to rinse or deliver hot water.
C7. hot mILK icon: to deliver a cup of steamed
milk.
C8. ItALIAn mACChIAto icon: to deliver a
shot of espresso with a small amount of
foam on top.
Installing the appliance
C9. LonG
icon: to deliver one cup of
C10. CAppuCCIno icon: to deliver
cappuccino.
C11. LAttE icon: to deliver a latte.
a
Important!
When you install the appliance, you should follow
the safety warnings below:
C12. p icon: to access the programming menu.
C13. ESC icon: to exit the selected function in
the menu.
•
The appliance gives off heat. After positioning
the appliance on the work top, leave a space
of at least 1 in (3 cm) between the appliance
and the side and rear walls and at least 6 in
(15 cm) above the coffee maker.
Water penetrating the appliance could cause
damage. Do not place the appliance near
taps or sinks.
The appliance could be damaged if the
water it contains freezes. Do not install the
appliance in a room where the temperature
could drop below freezing point.
C14.
C15.
C16.
icon: to select the coffee’s strength.
icon: to select the coffee size.
icon: to scroll backwards through the
programming menu.
•
•
Information : A light touch is enough to
activate the icon.
•
Arrange the power cable in such a way that
it cannot be damaged by sharp edges or
contact with hot surfaces (e.g. electric hot
plates).
Connecting the appliance
Important! Check that the power outlet
supply voltage corresponds to the value
indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed
and correctly installed outlet with a minimum
current rating of 12A only. If the power outlet
does not match the plug on the appliance, have
the outlet replaced with a suitable type by a
qualified professional.
10
Setting up the appliance
turnInG thE AppLIAnCE on
Information :
Information: In models provided with main
switch, before turning the appliance on, make
sure the main switch on the back of the appliance
is in the I position (fig. 1).
•
Coffee has been used to factory test the
appliance and it is therefore completely
normal for there to be traces of coffee in the
mill.
The machine is, however, guaranteed to be
new.
You should customize water hardness as
soon as possible following the instructions
in the section “Setting water hardness” on
page 20.
Each time the appliance is turned on, it performs
an automatic preheat and rinse cycle which
cannot be interrupted.
•
The appliance is ready for use only after
completion of this cycle.
Danger of burns! During rinsing, a little
hot water comes out of the coffee spouts and is
collected in the drip tray underneath.
1. Plug the appliance into the power outlet and
(in models provided with main switch) place
the main switch on the back of the appliance
in the I position (fig. 1).
Avoid contact with splashes of water.
You must first select the language (the
languages scroll through at intervals of about
two seconds):
2. When English appears, press the oK icon for
3 seconds (fig. 2). Once the language has
been saved, the message “English installed”
is displayed.
Follow the instructions indicated by the
appliance:
3. “FILL TANK!”: remove the water tank, fill to
the MAX line with fresh water then replace in
the appliance (fig. 3).
•
To turn the appliance on, press the button on
the left side of the machine (fig. 5): the
message “Heating up... please wait” is dis
When heating is complete, the message changes
to: “Rinsing”. As well as heating the boiler, this
also heats the internal circuits by circulating hot
water.
The appliance is at temperature when the
message “STANDARD COFFEE standard taste”
is displayed.
4. “INSERT WATER SPOUT AND PRESS OK”:
Check that the hot water spout is inserted on
the nozzle and place a container underneath
(fig. 4).
turnInG thE AppLIAnCE oFF
Each time the appliance is turned off, it performs
an automatic rinse cycle which cannot be
interrupted.
Press the oK icon (fig. 2). “PLEASE WAIT...” is
displayed and the appliance begins to deliver
hot water.
Danger of burns! During rinsing, a little hot
water flows from the coffee spouts.
Avoid contact with splashes of water.
The appliance ends the first start up procedure,
then the message “Turning off, please wait...” is
displayed and the appliance goes off.
The coffee maker is now ready for normal use.
To turn the appliance off, press the
button
(fig. 5). The appliance performs the rinse cycle
then goes off.
Information: In models provided with
main switch, if the appliance is not used for an
extended period, place the main switch on the
back of the appliance in the 0 position (fig. 6).
Information: When using the appliance
for the first time, you need to make 4-5 cups of
coffee and 4-5 cappuccinos before the appliance
starts to give satisfactory results.
11
5. Press the oK icon to confirm: the minutes
ChAnGInG thE mEnu SEttInGS
flash on the display;
Setting the language
To modify the language on the display, proceed
as follows:
6. Press the
minutes;
or
icon to change the
7. Press the OK icon to confirm: “Auto-start
Enabled?” is displayed;
8. Press the ESC icon to exit the menu: a symbol
appears next to the clock to indicate that
auto-start has been programmed.
To deactivate the function:
1. Press the p icon to enter the programming
menu;
2. Press the or
is displayed;
icon until “Set language”
3. Press the oK icon;
4. Press the
or
icon until the required
1. Press the p icon to enter the programming
menu;
language is displayed;
5. Press the oK icon to confirm (or the ESC
icon to cancel the operation);
6. Press the ESC icon to exit the menu.
2. Press the
or
icon until “Auto-start
Enabled?” is displayed;
3. Press the oK icon: the hours flash on the
display;
Setting the clock
To adjust the time on the display, proceed as
follows:
4. Press the ESC icon. This deactivates the
function and the
the display.
5. Press the ESC icon to exit the menu.
symbol disappears from
1. Press the p icon to enter the programming
menu;
Information : To activate this function, the
time must have been set previously.
2. Press the
or
icon until “Adjust time” is
displayed;
3. Press the oK icon: the hours flash on the
Setting the temperature
display;
To modify the temperature (low, medium, high)
of the water used to make the coffee, proceed
as follows:
4. Press the
or
icon to change the
hours;
5. Press the oK icon to confirm (or the ESC
icon to cancel the operation): the minutes
flash on the display;
1. Press the p icon to enter the menu;
2. Press the
is displayed;
or
icon until “Temperature”
6. Press the
or
icon to change the
minutes;
3. Press the oK icon;
4. Press the or
temperature (low, medium or high) is
displayed;
5. Press the oK icon to confirm (or the ESC
icon to cancel the operation);
7. Press the oK icon to confirm (or the ESC
icon to cancel the operation);
8. Press the ESC icon to exit the programming
menu.
icon until the required
Setting auto-start time
6. Press the ESC icon to exit the menu.
You can set the auto-start time in order to
have the appliance ready at a certain time (for
example in the morning) so you can make coffee
immediately.
1. Press the p icon to enter the programming
menu;
Setting auto-off
Information: The appliance is set to switch
automatically to stand-by if not used for 30
minutes. The time can be changed so that the
appliance switches off after 1 or 2 hours.
2. Press the
or
icon until “Auto-start
disabled” is displayed; “Enable?” is displayed
and the hours flash on the display;
3. Press the oK icon: the hours flash on the
display;
1. Press the p icon to enter the menu;
2. Press the
displayed;
or
icon until “Auto-off” is
icon until the required
3. Press the oK icon;
4. Press the or
4. Press the
hours;
or
icon to change the
12
number of hours of operation (30 minutes, 1
or 2 hours) is displayed;
5. Press the oK icon to confirm (or the ESC
icon to cancel the operation);
mAKInG CoFFEE
Selecting the coffee taste
The appliance is preset to make coffee with a
standard taste.
6. Press the ESC icon to exit the menu.
You can choose between 5 different coffee
tastes:
resetting default values (reset)
This resets all menu settings and programmed
quantities back to the default values (with the
exception of the language, time and beep which
remains as set as well as the counter for the
statistics function).
Extra-mild taste
Mild taste
Standard taste
Strong taste
1. Press the p icon to enter the menu;
Extra-strong taste
2. Press the or
is displayed;
icon until “Default values”
To change the flavor, press the
icon
3. Press the oK icon;
(fig. 7) repeatedly until the required taste is
displayed.
4. The message “Confirm?” is displayed.
5. Press the oK icon to confirm and exit (or the
ESC icon to cancel the operation).
Selecting the quantity of coffee in the cup
To select the quantity of coffee, press the
icon repeatedly (fig. 8) until the required quantity
of coffee is displayed. The quantities delivered
are different according to the type of coffee
selected:
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the p icon to enter the menu;
2. Press the
displayed;
or
icon until “Statistics” is
ESprESSo
LonG
3. Press the oK icon;
4. By pressing the or icon, you can check:
(oz)
CoFFEE (oz)
MY COFFEE
max: ≃6
max: ≃ 8.5
-
-
-
how many coffees have been made;
how many drinks with milk have been made;
how many times the machine has been
descaled;
SHORT
COFFEE
≃1.4
≃ 4.2
STANDARD
COFFEE
≃ 2
≃ 6
-
the total number of liters of water delivered;
5. Press the ESC icon twice to exit the menu.
LONG COFFEE
≃ 3
≃ 4
≃ 7
≃ 8.5
Acoustic signal (Beep enabled)
EXTRA LONG
COFFEE
This activates or deactivates the beep emitted
by the machine each time an icon is pressed or
an accessory is inserted/removed. The beep is
enabled by default.
1. Press the p icon to enter the menu;
2. Press the or icon until “Beep enabled” is
displayed;
3. Press the oK icon to confirm, “Confirm?” is
displayed;
4. Press the oK icon again to confirm activation
or the ESC icon to deactivate the function;
5. Press the ESC icon to exit the menu.
programming the espresso “my coffee”
quantity
The appliance is set by default to automatically
deliver 1 oz of espresso coffee.
To modify this quantity, proceed as follows:
1. Press the
“MY COFFEE” is displayed.
2. Press and hold the one cup
icon repeatedly (fig. 8) until
icon (fig. 9)
for about 8 seconds until “Program quantity”
is displayed, then release. The machine
starts delivering the coffee and the
flashes;
Information : The descale and water hard-
ness functions will be explained later in the
manual.
icon
3. As soon as the coffee in the cup reaches the
13
making espresso coffee using coffee beans
required level, press the
icon again.
The quantity set has now been programmed.
Important! Do not use caramelized or
candied coffee beans as they could stick to the
coffee mill and make it unusable.
Information: This setting is valid for mak-
ing both one and two cups. You cannot program
a quantity for two cups. To obtain 2 quantities of
1. Fill the container with coffee beans (fig. 12).
2. Place under the coffee spouts:
- one cup, if you want one coffee (fig. 13);
- two cups, if you want two coffees (fig. 14);
3. Lower the spouts as near as possible to the
cup. This makes a creamier coffee (fig. 15).
4. Choose the strength by hitting the
“my coffee press the
button.
programming the long “my coffee” quantity
The appliance is set by default to automatically
deliver ≃ 3.4 oz of LONG coffee. To modify this
quantity, proceed as follows:
1. Press the
icon repeatedly (fig. 8) until
“MY COFFEE” is displayed.
2. Press the LonG
and size by hitting the
.
icon (fig. 10) until “Pro-
5. Press the icon corresponding to the number
gram quantity” is displayed, then release.
The machine starts delivering the coffee and
the LonG icon flashes;
of coffees required (one cup
or two cups
) (fig. 9 and 16).
6. Preparation begins. A progress bar appears
on the display and gradually advances as the
procedure progresses (fig. 17).
Once the coffee has been made, the appliance is
ready to use again.
3. As soon as the coffee in the cup reaches the
required level, press the LonG icon again.
The quantity set has now been programmed.
regulating the coffee mill
The coffee mill is preset in the factory to prepare
coffee correctly and should not require regulating
initially.
However, if after making the first few coffees
you find that delivery is either too fast or too
slow (a drop at a time), this can be corrected
by regulating the grinding adjustment knob (fig.
11).
Information:
•
•
While the machine is making coffee, delivery
can be interrupted at any moment by pressing
the lit cup icon.
For a hotter coffee, before delivery rinse the
appliance through by pressing the
and confirming with the OK icon. Hot water
flows out of the coffee spouts and heats the
internal circuit of the machine so that the
coffee delivered will be hotter.
For an even hotter coffee, heat the cups by
rinsing them with the hot water.
If the coffee is delivered in drops, too fast
and not creamy enough or too cold, read the
tips in the “Troubleshooting” section on page
22.
icon
Important! The grinding coarseness
regulator must only be turned when the coffee
mill is in operation (when you hear the grinder
in motion).
•
•
For slower coffee delivery
and a creamier coffee, turn
one click towards “1” (finer
ground coffee).
making long coffee using coffee beans
For more rapid coffee deliv-
ery (not in drops), turn one
click towards “7” (coarser
ground coffee).
Information:
activated, a long coffee similar to drip coffee is
obtained.
When this function is
Important! Do not use caramelized or
candied coffee beans as they could stick to the
coffee mill and make it unusable.
Information: These adjustments will only
be evident after at least two cups of coffee have
been made.
1. Fill the container with coffee beans (fig. 12).
2. Adjust the height of the spout according to
14
the cup used. Put the cup for long coffee
under the spouts (fig. 18);
3. Choose the strength by hitting the
mAKInG DrInKS WIth mILK
Filling and attaching the milk container
1. Turn the lid of the milk container clockwise
until it becomes noticeably difficult to turn,
then remove the lid (fig. 20).
2. Fill the milk container with a sufficient
quantity of milk, not exceeding the MAX level
marked on the handle (fig. 21).
and size by hitting the
.
4. Press the LonG icon (fig. 10). Preparation
begins. A progress bar appears on the display
and gradually advances as the procedure
progresses.
Information:
Information! We recommend using skim
or 2% milk at refrigerator temperature (about
41°F). To avoid milk with poor froth or large
bubbles, always clean the milk lid and hot water
nozzle as described in the section “Cleaning the
milk container” on page 19.
•
While the machine is making coffee, delivery
can be interrupted at any moment by pressing
the LonG icon.
Only one cup of long coffee can be made at a
time.
When delivering more than 4.2 oz, the
appliance automatically grinds more coffee
halfway through delivery.
•
•
3. Make sure the milk intake tube is correctly
inserted in the bottom of the milk container
lid (fig. 22).
4. Replace the milk container lid and turn
counterclockwise as far as it will go until you
hear it click.
making espresso or long coffee using pre-
ground coffee
Important!
•
•
Never add pre-ground coffee when the
machine is off or it could spread through the
inside of the machine and dirty it.
Never use more than one level measuring
scoop or it could dirty the inside of the
machine or block the funnel.
5. Remove the hot water spout from the nozzle
(fig. 23).
6. Attach the container to the nozzle and push as
far as it will go (fig. 24). The machine emits
a beep when milk container is attached
correctly (if the beep function is enabled).
7. Place a sufficiently large cup under the coffee
spouts and frothed milk spout.
Information: If you use pre-ground coffee,
you can only make one cup of coffee at a time.
To use particularly tall cups/glasses, raise
the lid (A17) of the special compartment in
the cup tray (fig. 25).
1. Press the icon repeatedly (fig. 7)
until “Pre-ground” flashes on the display.
2. Put one level measuring scoop of pre-ground
coffee into the funnel (fig. 19).
3. Place a cup under the coffee spouts.
4. To make espresso coffee, press the one cup
icon (fig. 9). To make a long coffee,
press the LonG icon (fig. 10).
making latte
1. After attaching the milk container, place
frothed milk regulator (B1) on lid to position
2 for LATTE (fig. 26).
2. Press the LAttE icon (fig. 27).
The message “Caffelatte... Jug selector in
position: 2” appears. After a few seconds,
frothed milk is delivered from the milk
spout into the cup below. The milk will stop
automatically and delivery of coffee will
begin.
Information: LonG CoFFEE: when deliver-
ing more than 4.2 oz, the appliance requests a
new level measure of pre-ground coffee halfway
through delivery. When you have added the pre-
ground coffee, confirm by pressing the oK icon.
Information: If during delivery you want
to stop preparing milk, press the LATTE icon or
interrupt preparation of the coffee by pressing
the
icon.
15
making cappuccino
Cleaning the milk container after use
1. After attaching the milk container, place
frothed milk regulator (B1) on lid to position
2 for CAPPUCCINO (fig. 28). the quantity
of froth can be adjusted by moving the
regulator towards number 2 for a denser
froth.
moving it towards number 1 obtains a less
dense froth.
2. Press the CAppuCCIno icon (fig. 29). The
message “Cappuccino... Jug selector in
position: 1” appears . After a few seconds,
frothed milk flows out of the milk spout into
the cup below.
Important! Danger of burns When cleaning
the internal tubes of the milk container, a little hot
water comes out of the frothed milk tube (B5).
Avoid contact with splashes of water.
When “Press CLEAN button” flashes on the
display (each time you use a milk function):
1. Leave the jug attached the machine (you do
not need to empty it);
2. Place a cup or other recipient under the
frothed milk spout.
3. Press the CLEAN button (fig. 32) and keep
pressing until the progress bar which
appears on the display together with the
message “Cleaning...” is complete.
4. Remove the milk container and always clean
the nozzle with a sponge (fig. 33).
The milk will stop automatically and delivery
of coffee will begin.
Information! If during delivery you want to
stop preparing milk, press the CAppuCCIno icon
or interrupt preparation of the coffee by pressing
Information!
the
icon.
•
•
When “Press CLEAN button” flashes on the
display, you can still prepare any type of
coffee or milk. If you have to make a number
of drinks with milk, wait until you have
delivered the last cup before cleaning the
container.
making Italian macchiato
1. After attaching the milk container, place
frothed milk regulator (B1) on lid to position
2 for ITALIAN MACCHIATO (fig. 28)
2. Press the ItALIAn mACChIAto icon (fig.
30). The message “Macchiato... Jug selector
in position: 2” appears.
The milk left in the jug can be kept in the
refrigerator.
After a few seconds, frothed milk flows out
of the milk spout into the cup below.
The milk will stop automatically and delivery
of coffee will begin.
programming the size for each beverage
button
The appliance is factory preset to automatically
deliver standard quantities.
Information: If during delivery you want to
stop preparing milk, press the italian MACCHIATO
icon or interrupt preparation of the coffee by
To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk
spout.
pressing the
icon.
2. Press the icon corresponding to the function
you want to program (LATTE, CAPPUCCINO,
ITALIAN MACCHIATO or HOT MILK) until
“Milk for... Program quantity” appears on
the display and the icon corresponding to
the selected function flashes.
making hot milk
1. After attaching the milk container, position
the frothed milk regulator (B1) according to
the quantity of froth you require (pos. 1 =
little froth; pos. 2 = abundant froth).
2. Press the hot mILK icon (fig. 31). “HOT
MILK” appears on the display and after a few
seconds, frothed milk is delivered from the
milk spout into the cup below. Delivery of
milk stops automatically.
3. Release the icon. The appliance starts
delivering milk.
4. When the required quantity of milk has been
delivered into the cup, press the icon again.
5. After a few seconds, the appliance starts
delivering coffee into the cup and the
message “Coffee for... Program quantity”
is displayed (with the exception of the HOT
Information: If during delivery you want to
stop preparing milk, press the hot mILK icon
once.
MILK function) and the
icon flashes.
16
6. As soon as the coffee in the cup reaches the
CLEAnInG
required level, press the
delivery stops.
icon. Coffee
Cleaning the coffee maker
The following parts of the appliance must be
cleaned regularly:
The machine is now reprogrammed with the new
quantities.
-
-
-
-
coffee grounds container (A18),
drip tray (A16),
water tank (A13),
coffee spouts (A20) and hot water nozzle
(A11),
hot WAtEr
preparation
Important! Danger of burns. Never leave
the machine unsupervised while delivering hot
water. The hot water spout becomes hot while
water is being delivered and must be held by the
handle only.
-
-
pre-ground coffee feed funnel (A8),
inside the machine, accessible after opening
the service door (A19),
brew group (A12),
milk container (B)
control panel (C)
-
-
-
1. Make sure the hot water spout is attached
correctly (fig. 4).
2. Place a container under the spout (as close
as possible to avoid splashes).
Important!
•
Do not use solvents, abrasive detergents
or alcohol to clean the coffee maker. With
De’Longhi superautomatic coffee makers,
you need not use chemical products to clean
the machine. The descaler recommended
by De’Longhi is made from natural and
completely biodegradable substances.
None of the components of the appliance can
be washed in a dishwasher with the exception
of the milk container (B).
3
Press the
“Rinsing” “Hot water...” is displayed.
4. Press the icon to select the “Hot water...”
icon (fig. 34). The message
function (the selected message flashes on
the display) and confirm the selection by
pressing the oK icon (or cancel the selection
by pressing the ESC icon).
•
•
5. Water flows out of the spout. Delivery stops
automatically after 8.5 oz (250ml).
6. To interrupt delivery of hot water manually,
Do not use metal objects to remove
encrustations or coffee deposits as they
could scratch metal or plastic surfaces.
press the
icon again.
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is
displayed,thegroundscontainermustbeemptied
and cleaned. Until the grounds container has
been cleaned, the appliance continues to display
the message and coffee cannot be made.
To clean:
Important! You should not deliver hot
water for more than two minutes at a time.
Changing the quantity
The appliance is factory preset to automatically
deliver8.5 oz(250ml). Tomodifythesequantities,
proceed as follows:
1. Position a container under the spouts.
2. Once the “Hot water” function has been
selected, press and hold the OK icon (about 8
seconds) until “Hot water Program quantity”
•
open the service door on the front of the
appliance (fig. 35), extract the drip tray (fig.
36), empty and clean.
•
Empty the grounds container (A18) and
clean thoroughly to remove all residues left
on the bottom.
appears and the
When the hot water in the cup reaches the
required level, press the icon again.
icon flashes.
•
Important! when removing the drip tray,
the grounds container must be emptied, even if
it is not completely full.
The machine is now reprogrammed with the new
quantity.
If this is not done, when you make the next
coffees, the grounds container may fill up more
than expected and clog the machine.
17
Cleaning the drip tray
Important! If the drip tray is not emptied
regularly, the water could overflow from the edge
and seep inside or around the machine. This
could damage the machine, the surface it rests
on or the surrounding area.
Cleaning the inside of the machine
1. Check regularly (about once a week) that the
inside of the machine is not dirty. If neces-
sary, remove coffee deposits with a dull knife
and sponge.
2. Remove the residues with a vacuum cleaner
(fig. 40).
The drip tray is fitted with a level indicator (red)
showing the level of water it contains (fig. 37).
Before the indicator protrudes from the cup tray,
the drip tray must be emptied and cleaned.
Cleaning the brew group
The brew group must be cleaned at least once
a month.
Important! The brew group (A8) must not
be removed when the appliance is on. Do not
attempt to use force to remove the brew group
as this could damage the machine.
To remove the tray:
1. Open the service door (fig. 35);
2. Remove the drip tray and the grounds
container (Fig. 36);
3. Empty the drip tray and grounds container
(A18) and wash them;
4. Replace the drip tray complete with grounds
container (A18);
5. Close the service door.
1. Make sure the machine is correctly turned
off (see Turning off, page 31).
2. Open the service door (fig. 35);
3. Remove the drip tray and grounds container
(fig. 36);
4. Press the two red release buttons inwards
and at the same time pull the brew group
outwards (fig. 41).
Cleaning the water tank
1. Clean the water tank (A13) regularly (about
once a month) with a damp cloth and a little
mild dish soap.
2. Clean to remove all soap residues, then rinse
the water tank thoroughly.
Important! Do not use detergents or liq-
uid soap to clean the brew group. The detergent
would remove the lubricant applied to the inside
of the piston, causing the brew group to seize up
and become unusable.
Cleaning the coffee nozzles
1. Clean the nozzle periodically using a sponge
5. Soak the brew group in water for about 5
minutes, then rinse under the tap.
6. After cleaning, replace the brew group by
sliding it onto the internal support and pin at
the bottom, then push the PUSH symbol fully
in until it clicks into place.
or cloth (fig. 38).
2. Check regularly that the holes in the coffee
spout are not blocked.
If necessary, remove coffee deposits with a
toothpick (fig. 39).
Cleaning the pre-ground coffee feed funnel
•
Check regularly (about once a month ) that
the pre-ground coffee funnel is not blocked.
If necessary, remove coffee deposits with a
dull knife.
Danger of electric shock! Before perform-
ing any cleaning operations, the machine must
be turned off and disconnected from the main
power supply. Never immerse the coffee maker
in water.
18
DESCALInG
Information!
Descale the machine when the message
“DESCALE!” flashes on the LCD display.
If the brew group is
difficult to insert, you
must first adapt it to the
Important! Descaler contains acids which
may irritate the skin and eyes. It is vital to adhere
to the manufacturer’s safety warnings given on
the descaler pack and the warnings relating to
the procedure to follow in the event of contact
with the skin and eyes.
right
dimension
by
pressing it forcefully from
the bottom and top as shown in the figure.
7. Once inserted, make sure the
two red buttons have snapped
out.
8. Replace the drip tray and
grounds container.
Information! Use De’Longhi recommended
descaler only. Under no circumstances should
you use sulphamic or acetic based descalers.
Their use invalidates the warranty. Failure to
descale the appliance as described above also
invalidates the warranty.
9. Close the service door.
Cleaning the milk container
Clean the milk container each time you prepare
milk as described below:
1. Clean the milk
container each
1. Turn the machine on.
2. Enter the programming menu by pressing
the p icon.
3. Press the
displayed.
4. Select by pressing the oK icon.
“Descaling Confirm?” is displayed. Press OK
to activate the function.
5. The message “ Add descaler. Confirm?” is
displayed.
6. Before confirming, empty the water tank
(A13).
time you prepare
milk as described
below:
or
icon until “Descaling” is
2. Remove the milk
spout and intake
tube.
3. Remove
selector
the
by
it
pulling
outwards.
4. Wash all the
Pour the descaler diluted with water
(respecting the proportions indicated on the
descaler bottle) into the water tank.
Place an empty container with a minimum
capacity of 50 oz (1.5 L) under the hot water
spout.
c o m p o n e n t s
thoroughly with
hot water and
mild dish soap.
All components
can be washed
in a dishwasher,
placing them in the top basket of the
dishwasher.
Important! Danger di of burns Hot water
containing descaler flows out of the hot water
spout. Avoid contact with splashes of water.
7. Confirm by pressing the oK icon.
8. The message “Descaling Underway...” is
displayed. The descaling program starts and
the descaler liquid comes out of the water
spout.
The descale program automatically performs a
series of rinses and pauses to remove limescale
deposits from inside the machine.
Make sure there are no milk residues left
inside the holes and the groove on the fine
end of the selector.
5. Check that the intake tube and spout are not
clogged with milk residues.
6. Replace the selector, milk spout and intake
tube.
7. Replace the lid on the milk container, turning
it counterclockwise to hook it in place.
After about 30 minutes, the message “Rinsing
FILL TANK!” is displayed.
19
Setting water hardness
1. Press the p icon to enter the programming
9. The appliance is now ready for rinsing
through with clean water.
menu.
2. Press the
hardness”.
3. Confirm the selection by pressing the oK
icon.
4. Press the
Remove the water tank, empty, rinse under
running water, fill with clean water and
replace. “Rinsing... Press OK” is displayed.
10. Empty the container used to collect the
descaler solution and replace it under the hot
water spout.
or
icon and select “Water
or
icon to set the number
of squares formed on the reactive strip (see
figure in the previous section).
5. Press the oK icon to confirm the setting.
6. Press the ESC icon to exit the menu.
11. Press the oK icon to start rinsing. Hot water
flows out of the spout and the message
“Rinsing...” is displayed.
12. When the water tank is completely empty,
the message “Rinsing complete... Press OK”
is displayed.
The machine is now reprogrammed with the new
water hardness setting.
13. Press the oK icon, fill the water tank and the
appliance is ready for use.
uSInG CompArtmEnt For LAttE
SEttInG WAtEr hArDnESS
The DESCALE message is displayed after a
period of time established according to water
hardness.
The machine is factory set for a hardness value
of 4 (very hard water).
GLASS
To accommodate larger latte cups under the cof-
fee spouts, lift compartment door (A17) towards
machine and place glass in compartment.
The machine can also be programmed according
to the actual hardness of the tap water in the
various regions, varying the frequency with
which the message is displayed.
soft water
l
slightly hard water
ll
hard water
lll
very hard water
llll
measuring water hardness
1. Remove the “TOTAL HARDNESS TEST”
indicator paper from its pack.
2. Immerse the paper completely in a glass of
water for about a second.
3. Remove the paper from the water and shake
lightly.
After about a minute, 1, 2, 3, or 4 red squares
form, depending on the hardness of the water.
Each square corresponds to one level.
20
DISpLAyED mESSAGES
DISpLAyED mESSAGE poSSIBLE CAuSE
rEmEDy
•
•
The water tank is empty or positioned
incorrectly.
•
•
Fill the tank with water and/or insert it
correctly, pushing it as far as it will go.
FILL TANK!
The grinding is too fine and the coffee is
delivered too slowly.
Make the coffee again and turn the
grinding adjustment knob one click
clockwise towards “7” while the coffee
mill is in operation. The effect is only
visible after delivering two coffees.
GROUND TOO FINE
ADJUST MILL!
Insert water spout and
press OK
•
•
The machine cannot make coffee as
there is air in the hydraulic circuit
•
•
Press the oK icon to deliver water from
the spout until it flows out normally.
The water spout is not inserted or is
inserted incorrectly.
Insert water spout as far as it will go.
INSERT WATER
SPOUT!
•
The grounds container is too full or
more than 3 days have passed since you
last made coffee (this guarantees correct
hygiene of the machine).
•
Empty the grounds container and clean,
then replace.
EMPTY GROUNDS
CONTAINER
Important: when removing the drip tray,
the grounds container MUST be emptied,
even if it is not completely full.
If this is not done, when you make the
next coffees, the grounds container may
fill up more than expected and clog the
machine.
•
After cleaning, the grounds container
has not been replaced.
•
Open the service door and insert the
grounds container.
If grounds container is inside the
machine and message is still displayed,
there may be a damaged mircoswitch
and customer service should be called.
INSERT GROUNDS
CONTAINER
•
•
•
•
•
The milk container is not inserted. .
The machine must be descaled.
•
•
•
•
•
Insert milk container as far as it will go.
INSERT MILK
CONTAINER!
The descaling procedure described in
the “Descaling” section needs to be
performed as soon as possible.
DESCALE!
Too much ground coffee has been used.
Select a milder taste or reduce the
quantity of pre-ground coffee, then make
the coffee again.
LESS COFFEE!
The “pre-ground coffee” function has
been selected without placing any pre-
ground coffee in the funnel.
Place pre-ground coffee in the funnel.
ADD PRE-GROUND
COFFEE!
The funnel (A8) is blocked.
Empty the funnel with the help of a
dull knife, as described in the section
“Cleaning the pre-ground coffee feed
funnel”.
•
•
•
The coffee beans have run out.
•
•
•
Fill bean container
FILL BEANS
CONTAINER!
The brew group has not been replaced
after cleaning.
Insert the brew group as described in the
section “Cleaning the brew group”.
INSERT BREW GROUP
ASSEMBLY!
The service door is open
Close the service door.
CLOSE DOOR!
21
DISpLAyED mESSAGE poSSIBLE CAuSE
rEmEDy
•
The inside of the appliance is very dirty.
•
Clean the inside of the appliance
GENERAL ALARM!
thoroughly as described in the section
“Cleaning the inside of the machine”.
If the message is still displayed after
cleaning, contact customer services.
•
•
Milk has been delivered recently and the
tubes inside the milk container must be
cleaned.
•
•
Press the CLEAN button and keep it
pressed until the progress bar which
appears on the display together with the
message “Cleaning” is complete.
PRESS CLEAN
BUTTON
The appliance is delivering a LONG
coffee of more than 4.2 oz (125 ml).
Add a level measure of pre-ground
coffee and confirm by pressing the oK
icon.
ADD PRE-GROUND
COFFEE!
PRESS OK
trouBLEShootInG
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact customer service.
proBLEm
poSSIBLE CAuSE
rEmEDy
•
•
The cups have not been preheated.
•
•
Warm the cups by rinsing them with hot
The coffee is not hot
water.
The brew group has cooled down
because 2-3 minutes have elapsed since
the last coffee was made.
Before making coffee, rinse as described
in the notes in the section “Preparing
coffee using coffee beans”.
•
The coffee is ground too coarsely.
•
Turn the grinding adjustment knob one
click anticlockwise towards “1” while the
coffee mill is in operation (fig. 11).
Continue one click at a time until coffee
delivery is satisfactory.
The coffee is not
creamy enough
The effect is only visible after delivering
two coffees.
•
•
Wrong type of coffee.
•
•
Use a type of coffee for espresso coffee
makers.
The coffee is ground too finely.
Turn the grinding adjustment knob
one click clockwise towards “7” while
the coffee mill is in operation (fig. 11).
Continue one click at a time until coffee
delivery is satisfactory. The effect is only
visible after delivering two coffees.
The coffee is delivered
too slowly or a drop at
a time.
•
•
The coffee is ground too coarsely.
The spouts are blocked.
•
•
Avoid turning the grinding coarseness
regulator excessively otherwise when
you select two cups, the coffee may be
delivered a drop at a time.
The effect is only visible after delivering
two coffees.
The coffee is delivered
too quickly.
Clean the spouts with a toothpick (fig.
39).
Coffee does not come
out of one of the
spouts.
•
•
The holes in the spouts are clogged with
•
•
Clean the spouts with a toothpick,
The coffee does not
come out of the spouts,
but from around the
service door (A19).
dry coffee dust.
sponge or hard bristled kitchen brush.
The coffee guide (A21) inside the service
door is blocked and cannot swing.
Thoroughly clean the coffee guide
(A21), particularly near the hinges.
22
proBLEm
poSSIBLE CAuSE
rEmEDy
•
The milk is not cold enough or is not
semi-skimmed.
•
You should ideally use skimmed or semi-
skimmed milk at refrigerator temperature
(about 41°F).
If the result is still disappointing, try
another brand of milk.
The milk contains
bubbles or squirts out
of the milk spout
•
•
The milk frother selector is incorrectly
•
•
Adjust following the instructions in the
adjusted.
section on preparing drinks with milk.
The milk container lid is dirty.
Clean the milk container lid as described
in the section “Cleaning the milk
container”.
•
•
It is not plugged into the power outlet.
Il caffè è macinato troppo fine.
•
•
Plug into the power outlet.
The appliance does not
come on.
Ruotare la manopola di regolazione
macinatura di uno scatto verso il numero
7 in senso orario, mentre il macinacaffè
è in funzione (fig. 11). Procedere
Il caffè LonG ha troppa
crema
uno scatto alla volta fino ad ottenere
un’erogazione soddisfacente. L’effetto è
visibile solo dopo l’erogazione di 2 caffè.
23
This warranty applies to Super Automatic Espresso Machines with the De’Longhi brand name.
LImItED WArrAnty
What does the warranty cover?
We warrant each appliance to be free from defects in material and workmanship. Our obligation under
this warranty is limited to repair at our factory or authorized service center of any defective parts or
part thereof, other than parts damaged in transit. The repaired or new model will be returned at the
company expense.
This warranty shall apply only if the appliance is used in accordance with the factory directions, which
accompany it, and on an alternating current ( AC ) circuit.
how long does the coverage last?
This warranty runs for two years ( 2 ) from the purchase date found on your receipt and applies only to
the original purchaser for use.
What is not covered by the warranty?
The warranty does not cover defects or damage of the appliance, which result from repairs or alterations
to the appliance outside our factory or authorized service centers, nor shall it apply to any appliance,
which has been subject to abuse, misuse, negligence or accidents. Also, consequential and incidental
damage resulting from the use of this product or arising out of any breach of contract or breach of this
warranty are not recoverable under this warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damage, so the above limitation may not apply to you.
how do you get service?
If repairs become necessary, see contact information below:
u.S. residents:
Please contact our toll free hotline at 1-866-528-8323 (1-866-Latte-Best) or log onto our website at
For all accessories, spare parts or replacement parts, please contact our parts division at 1-800-865-
6330.
residents of Canada:
Residents of Canada: Please contact our toll free hotline at 1-888-335-6644 or log onto our website at
residents of mexico:
Please refer to the Limited Warranty statement for Mexico (see page 63 ).
Please refer to the back page of the manual for De’Longhi addresses.
The above warranty is in lieu of all other express warranties and representations. All implied warranties
are limited to the applicable warranty period set forth above. This limitation does not apply if you enter
into an extended warranty with De’Longhi. Some states do not allow limitations on how long an implied
warranty lasts, so the above exclusions may not apply to you. De’Longhi does not authorize any other
person or company to assume for it any liability in connection with the sale or use of its appliance.
how does state law apply?
This warranty gives you specific legal rights, and you may also have other rights, which vary from state
to state
24
|