A2-5732131300 6-12-2004 11:43 Pagina 1
IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
MODE D’EMPLOI IMPORTANT
CONSERVEZ LES PRESENTES INSTRUCTIONS
INSTRUCIONES IMPORTANTES
REPASE Y GUARDE ESTAS INSTRUCCIONES
LEA ESTE INSTRUCTIVO ANTES DE UTILIZAR EL APARATO
ISTRUZIONI IMPORTANTI
CONSERVARE LE ISTRUZIONI
COFFEE MAKER TYPE BAR 32/CAFETERIE MODÈLE BAR 32/CAFETERA ELECTRICA MODELO BAR 32/
MACCHINA DA CAFFÈ BAR32
Register this product on-line and receive a free trial issue of Cook's Illustrated. Visit www.prodregister.com/delonghi.
Enregistrez ce produit en ligne et recevez un numéro gratuit de Cook's Illustrated. Visitez www.prodregister.com/delonghi.
Visitez www.delonghi.com pour y voir une liste des centres de réparation proches de chez vous. (É.-U. et Canada).
Registre este producto en línea y reciba un ejemplar gratis de Cook's Illustrated. Visite www.prodregister.com/delonghi.
Visite www.delonghi.com para ver la lista de centros de servicios cercanos a usted. (Estados Unidos y Canada)
Registra questo prodotto "on-line" per ricevere una copia omaggio della rivista. Visita www.prodregister.com/delonghi.
Visita www.delonghi.com per una lista dei centri di servizio a te piu vicini. (Stati Uniti e Canada)
ELECTRONIC CHARACTERISTICS: CARACTÉRISTIQUES ÉLECTRIQUES: CARACTERISTICAS ELECTRICAS:
CARATTERISTICHE ELETTRICHE: 120V-60HZ 1100W
A2-5732131300 6-12-2004 11:43 Pagina 3
A2-5732131300 6-12-2004 11:43 Pagina 4
A2-5732131300 6-12-2004 11:43 Pagina 5
EC190/200 GB 6-12-2004 12:38 Pagina 6
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the
following:
•
•
•
Read all instructions.
Do not touch hot surfaces. Use handles and knobs.
To protect against fire, electrical shock and personal injury, do not immerse cord, plug or appliance in
water or other liquid.
•
•
Never allow the appliance to be used by children
Unplug from the outlet when not in use and before cleaning. Allow to cool before fitting or taking off parts,
and before cleaning the appliance.
•
•
Do not operate with a damaged cord or plug, or after the appliance malfunctions, or has been damaged
in any manner. Return the appliance to the nearest authorized service facility for examination, repair or
adjustment.
The use of accessory attachments or spare parts not recommended by the appliance manufacturer may
result in fire, electrical shock or personal injury.
•
•
•
•
•
Do not use outdoors.
Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
Do not place on or near a hot gas or electrical burner, or in a heated oven.
Plug cord into the wall outlet. To disconnect, turn any control to “off”, then remove plug from wall outlet.
Do not use the appliance for other than the intended use. This appliance is to be utilized for domestic use
only. Any other use is to be considered improper and therefore, dangerous.
•
DO NOT unscrew or remove boiler cap while the machine is in operation. Wait until brewing cycle is
completed and all water and steam has been used up.
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY
SHORT CORD INSTRUCTIONS
A short power cord is provided to reduce risks resulting from becoming entangled in or tripping over a
longer cord.
-
-
-
Longer, detachable power supply cords or extension cords are available and may be used if care is
exercised in their use.
If an extension cord is used, the marked electrical rating should be at least as great as the electrical rating
of the appliance. If the appliance is provided with 3- wire, grounding type cord, the extension should be
a GROUNDING TYPE 3 - WIRE CORD. The longer cord should be arranged so that it will not drape over
the counter-top or table top where it can be pulled on by children or tripped over.
-
Your product is equipped with a polarized alternating current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
6
EC190/200 GB 6-12-2004 12:38 Pagina 7
Read this manual thoroughly before installing and • If it requires repair, contact an authorized service
using the appliance.
This is the only way to ensure best results and
maximum safety for the user.
center only and ask for original spare parts to be
used.
• Failure to respect the above could reduce the safety
of the appliance.
• The power cable for this appliance must not be
replaced by the user as this operation requires the
use of special tools.
• If the cable is damaged or requires replacing,
contact an authorized service center only to avoid all
risks.
DESCRIPTION
(see figure on page 3).
The terminology below will be used repeatedly on the
following pages.
1
2
3
4
5
6
7
8
9
One filter holder
Large filter for 2 cups ground coffee
Small filter for 1 cup ground coffee or 1 pod
Steam knob
INSTALLATION
• Place the appliance on a work surface away from
taps and sinks.
Tamper
Cup tray
Power cable
Temperature OK light (coffee/hot water or steam)
light (appliance on)
• Check that the voltage of the power supply
corresponds to the value indicated on the appliance
rating plate.
• Connect the appliance to an efficiently grounded
outlet with a minimum current rating of 10 A only.
• The manufacturer may not be considered liable for
possible incidents caused by the failure to
adequately ground the outlet.
• If the plug fitted to the appliance does not match the
power outlet, have the outlet replaced with a suitable
type by a qualified professional.
• Never install the appliance in environments where
the temperature may reach 0°C (32°F) or lower (the
appliance may be damaged if the water freezes).
• If the power cable is longer than the distance
required to reach the mains outlet, the extra length
can be stored inside the appliance by pushing the
cable back through the cable opening.
10 Function selector knob
11
position to run off coffee/hot water
12 Off position
13 Steam position
14 Coffee measure
15 Boiler outlet
16 Steam/hot water tube
17 Jet frother
18 Water tank
19 Water tank lid
SAFETY WARNINGS
• This appliance is designed to "make espresso coffee"
and "hot drinks". Use with care to avoid scalds from
the water and steam jets or through incorrect use.
• Never touch hot parts.
• After removing the packaging, make sure the
product is complete. If in doubt, do not use the
appliance and contact a De’Longhi Customer
Service.
• The packing elements (plastic bags, polystyrene
foam, etc.) should be kept out of the reach of children
as they are a safety hazard.
• This appliance is intended for domestic use only. Any
other use is considered improper and thus
dangerous.
• The power cable can be positioned to the right or left
according to the location of the nearest outlet, resting
it in the guides on the bottom of the appliance (fig.
1).
When the power cable is in the required position,
make sure it is correctly held in place by the clips on
the bottom of the appliance (fig. 1).
• The manufacturer cannot be held responsible for any
damage caused through incorrect, wrong or
unreasonable use.
• Never touch the appliance with wet or damp hands.
• Never let children use the appliance without
supervision.
• Never allow children to play with the appliance.
• In the event of malfunction or faulty operation, switch
off and do not attempt to repair.
7
EC190/200 GB 6-12-2004 12:38 Pagina 8
for two coffees.
HOW TO MAKE ESPRESSO COFFEE
FILLING THE WATER TANK
Remove the water tank lid (fig. 2) and then take out the
tank by pulling upwards (fig. 3).
Fill the tank with fresh clean water taking care not to
exceed the MAX level (fig. 4).
Replace the tank, pressing lightly to open the valve
located on the bottom of the tank.
More simply, the tank can also be filled without
removing it, pouring the water directly from a jug.
IMPORTANT: It is normal for there to be water in the
space under the tank. This should therefore be dried
regularly with a clean sponge.
Note: Never use the appliance without water in the
tank and always remember to top up when the level
drops to about an inch from the bottom.
2.To make a single coffee only, place one level measure
of ground coffee, about 7 grams, in the filter (fig. 10).
To prepare two coffees, place two loosely filled
measures of ground coffee (about 6+6 g) in the filter.
Fill the filter a little at a time to prevent the ground
coffee from overflowing.
IMPORTANT: for correct operation, before adding the
ground coffee to the filter, clean the filter from
residues of ground coffee from the previous infusion.
3.Distribute the ground coffee evenly and press lightly
with the tamper (fig. 11). Note: Correct pressing of
the ground coffee is essential to obtain a good
espresso. If pressing is excessive, coffee delivery will
be slow and the froth will be dark. If pressing is too
light, coffee delivery will be too rapid and the froth
will be skimpy and light colored.
PREHEATING THE COFFEE UNIT
4.Remove any excess coffee from the rim of the filter
holder and attach the filter holder to the appliance.
Rotate firmly (fig. 6) to avoid leaks of water.
5.Place the cup or cups (ideally preheated by rinsing
with a little hot water) under the filter holder spouts
(fig. 12).
To obtain espresso coffee at the ideal temperature, it is
recommended that the coffee machine be preheated.
Turn the selector knob to the
position (fig. 5) before
making coffee, making sure the filter holder is attached
to the appliance (check that the steam knob is closed).
To attach the filter holder, position it under the boiler
outlet with the handle towards the left (see fig. 6), push
it upwards and at the same time rotate the handle
towards the right. Rotate firmly. Wait until the
preheating process is complete, and then make coffee
as described in the following chapter.
6.Make sure the OK light (fig. 7) is on (if off, wait until
it comes on), then turn the knob to the
position
(fig. 8) until the required quantity is obtained. To
interrupt, place the selector back in the
(fig. 5).
position
7.To remove the filter holder, rotate the handle from
right to left.
IMPORTANT: to avoid splashes, never remove the
filter holder while the appliance is delivering
coffee.
8.To eliminate the used coffee grounds, block the filter
in place using the lever incorporated in the handle
and empty the coffee by turning the filter holder
upside down and tapping (fig. 13).
9.To turn the appliance off, rotate the selector knob to
the "O" position (fig. 14).
Alternatively, preheating can be achieved more rapidly
proceeding as follows:
1.Turn the appliance on by rotating the selector knob to
the
position (fig. 5) and attach the filter holder to
the appliance without adding ground coffee.
2.Place a cup under the filter holder. Use the same cup
as will be used to prepare the coffee in order to
preheat it.
3.Wait for the OK indicator light to come on (fig. 7),
then immediately rotate the selector knob to the
position (fig. 8), run the water off until the OK
indicator light goes out, then interrupt delivery by
IMPORTANT: the first time the appliance is used, all
accessories must be washed thoroughly by making at
least five coffees without using ground coffee.
rotating the selector knob to the
position (fig. 5).
4.Empty the cup. Wait until the OK indicator light
comes on again then repeat the same operation.
HOW TO PREPARE ESPRESSO COFFEE USING THE
FILTER FOR GROUND COFFEE
1.After preheating the appliance as described above,
place the ground coffee filter in the filter holder,
making sure the projection is correctly inserted in the
slot as shown in fig. 9. For appliances with two
filters, use the smallest for one coffee and the largest
8
EC190/200 GB 6-12-2004 12:38 Pagina 9
HOW TO PREPARE ESPRESSO COFFEE USING PODS 7.Pour the frothed milk into the cups containing the
(FOR APPLIANCES WITH TWO FILTERS ONLY)
1.Preheat the appliance as described in the section
"PREHEATING THE COFFEE UNIT", making sure the
filter holder is attached.
espresso coffee prepared previously.
The cappuccino is ready. Sweeten to taste and if
desired, sprinkle the froth with a little cocoa powder.
Note: to make coffee again after the milk has been
frothed, cool down the boiler first or the coffee will
burn. To cool, place a container under the boiler
outlet, turn the selector to the "coffee" position and
run off the water until the OK light goes out. Turn the
NOTE: use pods conforming to the ESE standard,
indicated on the pack by the following symbol:
selector back to the
as described above.
position and make the coffee
IMPORTANT: always clean the Jet Frother after use.
Proceed as follows:
1.Discharge a little steam for a few seconds by rotating
the steam knob (fig. 18).
2.Wait several minutes for the steam tube to cool
down. Unscrew the cappuccino maker by rotating
clockwise (fig. 20) and wash thoroughly with warm
water.
3.Make sure the three holes in the cappuccino maker
shown in fig. 21 are not blocked. If necessary, clean
with a pin.
The ESE standard is a system accepted by leading pod
producers and enables espresso coffee to be prepared
simply and cleanly.
2.Place the small 1 coffee or pod filter in the filter
holder, making sure the projection is correctly
inserted in the slot as shown in fig. 12.
3.Insert a pod, centering it as far as possible on the
filter (fig. 15).Always follow the instructions on the
pod pack to position the pod on the filter correctly.
4.Attach the filter holder to the appliance. Always
rotate as far as it will go (fig. 6).
5.Proceed as in points 5, 6 and 7 in the previous
paragraph.
4.Clean the steam tube, taking care to avoid burns.
5.Screw the cappuccino maker back in place.
HOW TO MAKE CAPPUCCINO COFFEE
1.Prepare the espresso coffees as described in the
previous paragraphs, using sufficiently large cups.
HOT WATER PRODUCTION
1.Turn the appliance on by rotating the selector knob to
2.Rotate the selector knob to the
position (fig. 16)
the
position (fig. 5).
and wait until the OK light comes on (fig. 7). This
indicates that the boiler has reached the ideal
temperature for steam production.
2.Place a container under the cappuccino maker.
3.When the OK indicator light comes on, turn the
selector knob to the
position (fig. 8) and at the
1
3.In the meantime, fill a container with about 3 /
2
same time, rotate the steam knob counter -clockwise
(fig. 18). Hot water is delivered from the Jet Frother.
4.To interrupt delivery of hot water, rotate the steam
knob clockwise and position the selector knob to "O"
(fig. 14).
ounces of milk for each cappuccino to be prepared.
The milk must be at refrigerator temperature (not
hot!). In choosing the size of the container, bear in
mind that the milk doubles or triples in volume.
Note: You are recommended to use skim milk at
refrigerator temperature.
CLEANING AND MAINTENANCE OF THE
FILTER
About every 300 coffees or when the coffee drips out
of the filter holder or not at all, clean the ground coffee
filter holder as follows:
4.Place the container with milk under the Jet Frother
(fig. 17).
5.Immerse the Jet Frother in the milk about 1/4 of an inch
and rotate the steam knob counter-clockwise (fig. 18)
(rotating the knob more or less varies the quantity of steam
discharged by the Jet Frother). The milk now starts to
increase in volume and take on a creamy appearance.
6.When the milk has doubled in volume, immerse the
Jet Frother deeply and continue heating the milk (fig.
19). When the required temperature is reached (the
ideal is 60°C - 140°F), interrupt steam delivery by
rotating the steam knob clockwise and placing the
selector in the "O" position (fig. 14).
• Remove the filter from the filter holder.
• Remove the filter cap (fig. 22) by unscrewing in the
direction indicated by the arrow on the cap.
• Remove the frother from the container by pushing it
from the cap end.
• Remove the gasket (fig. 25).
• Rinse all components and clean the metal filter
thoroughly in hot water using a brush (fig. 23).
Make sure the holes in the metal filter are not
blocked. If necessary, clean with a pin (see fig. 24).
9
EC190/200 GB 6-12-2004 12:38 Pagina 10
• Replace the filter and gasket on the plastic disk as
shown in fig. 25.
DESCALING
You are recommended to descale the coffee machine
about every 200 coffees.
Make sure to insert the pin on the plastic disk into the
hole in the gasket indicated by the arrow in fig. 25.
• Replace the assembly in the steel filter container (fig.
26), making sure the pin is inserted into the hole in
the support (see arrow in fig. 26).
• Finally, screw on the cap (fig. 27).
Failure to clean as described above invalidates the
resulting.
You should use a commercially available product
specifically for descaling espresso coffee machines.
If such a product is not available, proceed as follows.
1.Fill the tank with one litre of water.
2.Dissolve 2 spoonfuls (about 1 ounce) of citric acid.
3.Rotate the selector knob to the
until the OK indicator light comes on.
4.Make sure the filter holder is not attached and
position a container under the boiler outlet.
position and wait
CLEANING THE BOILER OUTLET
About every 300 coffees, the espresso boiler outlet
must be cleaned as follows:
• Make sure the appliance is not hot and that it is
unplugged from the outlet.
• Using a screwdriver, unscrew the screw fixing the
espresso boiler outlet filter (fig. 28).
• Clean the outlet filter thoroughly in hot water using a
brush. Make sure the holes are not blocked. If
necessary, clean with a pin.
5.Rotate the selector knob to the
position (fig. 8)
and run off half the solution in the tank.
Then interrupt the flow by rotating the selector to the
"O" position (fig. 14).
6.Leave the solution to work for about 15 minutes, then
run off the rest of the water in the tank.
7.To eliminate residues of solution and scale, rinse the
tank well, fill with clean water and replace.
8.Rotate the selector knob to the
position (fig. 8)
Failure to clean as described above invalidates the
resulting.
and run off the water until the tank is completely
empty;
9 Rotate the selector knob to the
and repeat operations 7 and 8 again.
Repair of damage to the coffee machine caused by
scale is not covered by the resulting unless descaling is
performed regularly as described above.
position (fig. 5)
OTHER CLEANING OPERATIONS
1.Do not use solvents or abrasive cleaning products to
clean the appliance. A soft, damp cloth is sufficient.
2.Remove the drip tray, empty and wash frequently.
3.Clean the water tank regularly.
IMPORTANT: during cleaning, never immerse the
coffee machine in water. It is an electrical appliance.
10
EC190/200 GB 6-12-2004 12:38 Pagina 11
PROBLEM
POSSIBLE CAUSES
SOLUTION
• Ground coffee too damp and/or
packed down too tightly.
• Make the coffee again packing it
down less and/or using different
ground coffee.
• Fill the tank with water.
• Clean the spout holes
No espresso coffee is
delivered
• No water in the tank
• The holes in the filter holder spouts
are blocked.
• The espresso boiler outlet is blocked.
• Clean as described in the chapter
"Cleaning the boiler outlet".
• Clean as described in the section
"Cleaning the filter".
• The filter is blocked
• The tank is incorrectly inserted and
the valve on the bottom is not open.
• Press the tank down lightly to open
the valve on the bottom.
• The filter holder is inserted incorrectly.
• Attach the filter holder correctly and
rotate firmly as far as it will go.
The espresso coffee drips
from the edges of the filter
holder rather than the holes
• The espresso boiler gasket has lost
elasticity.
• Have the espresso boiler gasket
replaced at a service center.
• The holes in the filter holder spouts
are blocked.
• Clean the spout holes
• The espresso OK indicator light was
not on when the coffee switch was
pressed.
• Wait until the espresso OK indicator
light comes on.
The espresso coffee is cold
• No preheating performed
• Preheat as described in the
paragraph "Preheating the espresso
coffee unit".
• The cups were not preheated
• Preheat the cups.
• The water tank is empty.
• The tank is incorrectly inserted and
the valve on the bottom is not open.
•
•
The pump is excessively noisy
Refill the tank.
Press the tank down lightly to open
the valve on the bottom.
•
•
•
•
•
•
•
•
The coffee froth is too
light (delivered from the
spout too fast)
The ground coffee is not pressed
down firmly enough.
Press the ground coffee down more
firmly (fig. 11).
Increase the quantity of ground
coffee.
Use ground coffee for espresso coffee
machines only.
Change the type of ground coffee.
There is not enough ground coffee.
The ground coffee is too coarse
Incorrect type of ground coffee.
•
The coffee froth is too dark
(delivered from the spout too
slowly)
• The ground coffee is pressed down
too firmly.
• There is too much ground coffee.
• The espresso boiler outlet is blocked.
Press the coffee down less firmly (fig.
11).
Reduce the quantity of ground coffee.
Clean as described in the chapter
"Cleaning the espresso boiler outlet".
Clean as described in the section
"Cleaning the filter".
•
•
•
•
•
• The filter is blocked
• The ground coffee is too fine.
Use ground coffee for espresso coffee
machines only.
• The ground coffee is too fine or is
damp.
Use ground coffee for espresso coffee
machines only and make sure it is not
damp.
•
• Incorrect type of ground coffee.
Change the type of ground coffee.
•
•
No milk froth is formed when
making cappuccino
• Milk not cold enough.
• Jet Frother dirty.
Always use skim milk at refrigerator
temperature.
Thoroughly clean the holes in the Jet
Frother in particular those indicated
in figure 21.
11
EC190/200 GB 6-12-2004 12:38 Pagina 12
This warranty applies to all products with De’Longhi or Kenwood brand names.
LIMITED WARRANTY
What does the warranty cover?
We warrant each appliance to be free from defects in material and workmanship. Our obligation
under this warranty is limited to repair at our factory or authorized service center of any defective
parts or part thereof, other than parts damaged in transit. In the event of a products replacement or
return, the unit must be returned transportation prepaid. The repaired or new model will be returned
at the company expense.
This warranty shall apply only if the appliance is used in accordance with the factory directions,
which accompany it, and on an Alternating current ( AC ) circuit.
How long does the coverage last?
This warranty runs for one year ( 1 ) from the purchase date found on your receipt and applies only
to the original purchaser for use.
What is not covered by the warranty?
The warranty does not cover defects or damage of the appliance, which result from repairs or
alterations to the appliance outside our factory or authorized service centers, nor shall it apply to
any appliance, which has been subject to abuse, misuse, negligence or accidents. Also,
consequential and incidental damage resulting from the use of this product or arising out of any
breach of contract or breach of this warranty are not recoverable under this warranty. Some states
do not allow the exclusion or limitation of incidental or consequential damage, so the above
limitation may not apply to you.
How do you get service?
If repairs become necessary, see contact information below:
U.S. Residents:
Please contact our toll free hotline at 1-800-322-3848 or log onto our website at
For all accessories, spare parts or replacement parts, please contact our parts division at 1-800-
865-6330.
Residents of Canada:
Please contact our toll free hotline at 1-888-335-6644 or log onto our website at
Residents of Mexico:
Please refer to the Limited Warranty statement for Mexico.
Please refer to the back page of the manual for De’Longhi addresses.
The above warranty is in lieu of all other express warranties and representations. All implied
warranties are limited to the applicable warranty period set forth above. This limitation does not
apply if you enter into an extended warranty with De’Longhi. Some states do not allow limitations
on how long an implied warranty lasts, so the above exclusions may not apply to you. De’Longhi
does not authorize any other person or company to assume for it any liability in connection with the
sale or use of its appliance.
How does state law apply?
This warranty gives you specific legal rights, and you may also have other rights, which vary from
state to state.
12
|