BenQ M300
Mobile Phone User’s Manual
Safety Information
For your safety, please read the guidelines below carefully
before you use your phone:
Exposure to Radio Frequency Signals
Max. SAR measurement
EU: GSM900: 0.621 mW/g; DCS1800: 0.259 mW/g.
USA: PCS1900: 0.641 mW/g.
To avoid exceeding the FCC RF exposure limits, please do not wear
the phone in front of your chest.
SAR compliance for body-worn operations is restricted to belt-clips,
holsters or similar accessories that have no metallic component in the
assembly and must provide at least 1.5 cm separation between the device,
including its antenna, and the user's body.
Your wireless handheld portable telephone is a low power transmitter and
receiver. When it is ON, it receives and also sends out radio frequency
(RF) signals.
European and international agencies have set standards and
recommendations for the protection of public exposure to RF
electromagnetic energy.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996
• Verband Deutscher Elektringenieure (VDE) DIN- 0848
• Directives of the European Community, Directorate General V in
Matters of Radio Frequency Electromagnetic Energy
• National Radiological Protection Board of the United Kingdom, GS 11,
1988
• American National Standards Institute (ANSI) IEEE. C95.1- 1992
• National Council on Radiation Protection and Measurements (NCRP).
Report 86
Safety Information
i
• Department of Health and Welfare Canada. Safety Code 6
These standards are based on extensive scientific review. For example,
over 120 scientists, engineers and physicians from universities,
government health agencies and industry reviewed the available body of
research to develop the updated ANSI Standard.
The design of your phone complies with these standards when used
normally.
Specific Operating Restrictions
No metallic component allowed in body-worn accessories.
Antenna Care
Use only the supplied or approved replacement antenna. Unauthorized
antennas, modifications or attachments may damage the phone and
violate FCC regulations.
Phone Operation
Normal Position: Hold the phone as you would any other telephone with
the antenna pointed up and over your shoulder.
For your phone to operate most efficiently, do not touch the antenna
unnecessarily when the phone is in use. Contact with the antenna affects
call quality and may cause the phone to operate at higher power level than
otherwise needed.
Batteries
All batteries can cause property damage, injury or burns if a conductive
material such as jewelry, keys or beaded chains touches exposed terminals.
The material may complete electrical circuit and become quite hot. To
protect against such unwanted current drain, exercise care in handling any
charged battery, particularly when placing it inside your pocket, purse or
other container with metal objects. When battery is detached from the
phone, your batteries are packed with a protective battery cover; please
use this cover for storing your batteries when not in use.
ii
Safety Information
Driving
Check the laws and regulations on the use of wireless telephones in the
areas where you drive. Always obey them. Also, if using your phone while
driving, please:
• Give full attention to driving--driving safety is your first responsibility.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving
conditions so require.
Electronic Devices
Most modern electronic equipment is shielded from RF signals. However,
certain electronic equipment may not be shielded against the RF signals
from your wireless phone.
Pacemakers
The Health Industry Manufacturers Association recommends that a
minimum separation of six (6") inches be maintained between a handheld
wireless phone and a pacemaker to avoid potential interference with the
pacemaker. These recommendations are consistent with the independent
research by and recommendations of Wireless Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the phone more than six inches from their
pacemaker when the phone is turned ON.
• Should not carry the phone in a breast pocket.
• Should use the ear opposite the pacemaker to minimize the potential for
interference.
If you have any reason to suspect that the interference is taking place, turn
your phone OFF immediately.
Hearing Aids
Some digital wireless phones may interfere with some hearing aids. In the
event of such interference you may want to consult your hearing aid
manufacturer to discuss alternatives.
Safety Information
iii
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of
your device to determine if they are adequately shielded from external RF
energy. Your physician may be able to assist you in obtaining this
information.
Turn your phone OFF in health care facilities when any regulations posted
in these areas instruct you to do so. Hospitals or health care facilities may
be using equipment that could be sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles. Check with the manufacturer or its
representative regarding your vehicle. You should also consult the
manufacturer of any equipment that has been added to your vehicle.
Posted Facilities
Turn your phone OFF in any facility where posted notice so requires.
Aircraft
FCC regulations prohibit using your phone while in the air. Switch OFF
your phone before boarding an aircraft.
Blasting Areas
To avoid interfering with blasting operations, turn your phone OFF when
in a “blasting area” or in area posted “TURN OFF TWO-WAY RADIO.”
Obey all signs and instructions.
Potentially Explosive Atmospheres
Turn your phone OFF and do not remove the battery when in any area
with
a
potentially explosive atmosphere and obey all signs and
instructions. Sparks, from your battery, in such areas could cause an
explosion or fire resulting in bodily injury or even death.
iv
Safety Information
Areas with a potentially explosive atmosphere are often, but not always
clearly marked. They include fueling areas such as gasoline stations; below
deck on boats; fuel or chemical transfer or storage facilities; vehicles using
liquefied petroleum gas (such as propane or butane); areas where the air
contains chemicals or particles, such as grain, dust, or metal powders; and
any other area where you would normally be advised to turn off your
vehicle engine.
For Vehicles Equipped with an Air Bag
An air bag inflates with great force. DO NOT place objects, including both
installed or portable wireless equipment, in the area over the air bag or in
the air bag deployment area. If in-vehicle wireless equipment is
improperly installed and the air bag inflates, serious injury could result.
Federal Communications Commission
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiated radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Safety Information
v
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
European Union Directives Conformance Statement
This device complies with the OJ-Directive as below:
Electromagnetic Compatibility Directive (89/336/EEC), Low Voltage
Directive (73/23/EEC)
And R&TTE Directive (99/05/EEC).
And also complies with the standard:
3GPP TS 51.010-1
EN 301 511
EN 30360/ EN30361
ETSI EN 301 489-1/-7
EN 60950
vi
Safety Information
Table of Contents
2. Preparing Your Phone For Use................................... 1
Inserting Your SIM Card ..................................................... 1
Installing the Battery ............................................................ 2
Installing the Back Cover ..................................................... 2
Charging the Phone.............................................................. 3
Turning the Phone On......................................................... 4
3. Getting to Know Your Phone ..................................... 6
Your Phone at a Glance........................................................ 6
Standby Screen...................................................................... 8
Main Screen..............................................................................8
Icons in the LCD display's Status Bar......................................9
Using the Keys in the Standby Mode ....................................12
Menu Navigation................................................................ 15
Main menu map.....................................................................21
4. Using Your Phone ..................................................... 22
Making a Phone Call .......................................................... 22
Ending a Phone Call........................................................... 22
Answering a Phone Call ..................................................... 23
Rejecting an Incoming Call................................................ 23
Making an International Call............................................. 23
Making an Emergency Call................................................ 24
Dialing an Extension Number........................................... 24
Table of Contents
vii
Phone Book......................................................................... 26
SIM Card Phone Book ...........................................................29
Finding Contacts in the Phone Book ....................................30
Last Missed, Dialed, and Received Calls............................ 32
In-Call Menu ...................................................................... 35
Using the Silent Profile....................................................... 38
Camera Function................................................................ 39
Shortcuts Menu .................................................................. 42
Setting Function Shortcuts ....................................................42
Setting Phone Number Shortcuts..........................................44
Using Function and Phone Number Shortcuts....................45
Messages Menu................................................................... 46
SMS .........................................................................................47
MMS........................................................................................54
SMS Chat ................................................................................59
Voicemail................................................................................61
Cell Broadcast.........................................................................62
Memory Status .......................................................................63
Input Modes ....................................................................... 64
Changing the Text Input Mode.............................................64
Letter Input Mode (ABC)......................................................65
Numeric Input Mode (123)...................................................65
Predictive Input Mode (iTap) ...............................................65
viii
Table of Contents
Symbol Input Mode ...............................................................67
Direct Connection to URLs ............................................... 68
Phone Book......................................................................... 70
Find .........................................................................................70
Add..........................................................................................70
Delete ......................................................................................71
Caller Group...........................................................................71
Business Card .........................................................................72
My Number ............................................................................73
Memory Status .......................................................................73
Call Records........................................................................ 74
Missed Calls ............................................................................74
Received Calls.........................................................................74
Dialed Calls.............................................................................74
Cleanup All .............................................................................74
Call Duration..........................................................................74
Call Cost..................................................................................75
Messages.............................................................................. 76
Games.................................................................................. 77
Games......................................................................................77
Camera................................................................................ 80
Media Center ...................................................................... 80
Album .....................................................................................80
Image.......................................................................................81
Table of Contents
ix
Melody ....................................................................................82
Cleanup All .............................................................................83
Memory Status .......................................................................83
Tools.................................................................................... 84
Alarm ......................................................................................84
World Clock ...........................................................................85
Calendar..................................................................................86
Shortcuts.................................................................................87
Calculator................................................................................88
Currency Converter ...............................................................88
Stopwatch ...............................................................................89
Oper. Service....................................................................... 90
WAP Service ...........................................................................90
Settings.............................................................................. 104
Date & Time .........................................................................104
Auto Power On/Off..............................................................104
Profiles ..................................................................................105
Display ..................................................................................108
Audio.....................................................................................110
Call Settings ..........................................................................110
Network ................................................................................114
Security .................................................................................116
Power Saving Mode..............................................................118
Language...............................................................................118
Input......................................................................................119
Restore ..................................................................................119
6. Care and Maintenance ............................................ 120
x
Table of Contents
7. Troubleshooting...................................................... 121
Table of Contents
xi
xii
Table of Contents
Preparing Your Phone For Use
Inserting Your SIM Card
Slide the entire SIM card into the slot in the direction of arrow shown
on the compartment, with the metal contacts of the SIM card facing
down and the cut corner at the top left.
SIM card
A SIM card can be easily damaged if its metal contacts become
scratched. Therefore, take special care when holding or inserting it.
If you wish to remove the SIM card, you
must first press down the stay, then push
the SIM card out of the slot.
/
Stay
SIM card
Preparing Your Phone For Use
1
Installing the Battery
1. Place the battery onto the back of the phone, with the battery's
contacts facing downwards and the tab on its top edge in alignment
with the holes in the battery compartment.
2. Push the battery against the top of the compartment and press it
down to click it into the compartment.
Do not remove the battery when the phone is on. Doing so could
cause you to lose personal settings or data stored either on your SIM
card or in the phone's memory.
Installing the Back Cover
Place the back cover onto the back of your phone and slide forward
until the latch catches the cover.
2
Preparing Your Phone For Use
Charging the Phone
1. Insert the charger connector into the charger socket at the bottom
right of your phone. Make sure that the connector is inserted in the
right direction (with the arrow sign on the top ).
Charger socket
Charger connector
2. Plug the charger into a power outlet.
3. Once the phone is fully charged, remove the charger from both the
power outlet and the phone.
•Charging requires approximately 4 hours.
•When charging while the phone is turned off, the LCD display
/
shows the
animation. If the charging is performed while the
phone is on, the LCD display shows the
icon. The lines
showing the battery power level will scroll until the battery is fully
charged.
•When the battery is out of power, the phone will play an alert sound
to remind you to recharge it and then will automatically turn off.
Do not remove the battery while the phone is charging.
Preparing Your Phone For Use
3
Turning the Phone On
1. Long press
to turn the phone on. The phone
will display the welcome animation.
•You can select and set a welcome animation, image, or message
that will display when you turn on your phone, as well as the music
/
that will be played. Go to the menu: Settings → Display
→
Welcome Message. For details, please refer to page 108.
•If the welcoming music goes on too long, once the standby screen
comes up, you can press to stop playback.
2. Enter your PIN code. If you enter the PIN code incorrectly,
press
hold
(Clear) to delete the incorrect numerals. Press and
to delete all numerals that have been entered. After
completing entry of your PIN code, press
to confirm.
8
The PIN (Personal Identification Number) is a password provided by
a network operator with a SIM card. You need this password in order
to use the SIM card.
If you enter the PIN incorrectly 3 times in a row, the SIM card will lock
down and no longer be usable. If this happens, you must enter the
PUK (Personal Unblocking Key) for that SIM card in order to unlock
it. Please contact your network operator to obtain a PUK.
To cancel PIN password authentication, go to the menu Settings →
/
Security → PIN Code → PIN Code. Please see page 116.
4
Preparing Your Phone For Use
3. When the PIN code entered has been accepted, the phone will
automatically search for the designated network. This search process
may take a few seconds.
4. The standby screen will be displayed, as well as network signal
strength and the name of the network operator. You can now use the
phone.
8
8
If the phone cannot detect the network, the on-screen signal strength
meter will show no bars.
If the phone links to a network that you are not authorized to use, the
signal strength meter will show a level of zero. You will only be able to
make emergency calls.
Preparing Your Phone For Use
5
Bottom and back views
Hands-free headset/
Data cable jack
Charger socket
Wrist strap hole
Mirror used to take a
self portrait
Camera lens
Buzzer
Battery Contacts
Back cover
Battery compartment
SIM card holder
To avoid exceeding the FCC RF exposure limits, please do not wear
the phone in front of your chest.
Getting to Know Your Phone
7
Icons in the LCD display's Status Bar
•You can set the animation or image you wish to use as wallpaper
when the phone is in standby mode by going to the menu Media
/
Center → Album. Alternatively, you can go to the menu Settings
→ Display → Wallpaper. See page 80 and page 108.
•To set the current time and date, as well as the format in which they
will be shown on standby screen, go to the menu Settings → Date
& Time. See page 104.
•You can go to the menu Settings → Profiles → Personal to
change the name of the profile to your own user name. When this
profile is activated, your own name will appear in the standby
screen on the LCD display. For details, see page 106.
•For enhanced security, you can use the screen lock function. Go to
the menu Settings → Security → Screen Lock. If the screen lock
is activated, and you have not performed any tasks with the phone
for a set time, the phone will automatically bring up the screen lock
image. The purpose is to protect any personal data on your phone
from being read by other persons. To restore the original display
screen, you must enter a password that you provide for this
function. For details on settings, see page 118.
•After the standby screen remains idle for 10 seconds, the soft key
bar, time and date, as well as all the other words currently displayed
will automatically disappear, showing the full-screen wallpaper. You
can also press
to display/hide the status bar and words
normally shown on the standby screen.
Icon
Function
Description
Signal strength of the network. The more
bars indicated, the stronger the signal.
Signal strength
Getting to Know Your Phone
9
Icon
Function
Description
Shows the current level of battery power.
The more bars indicated, the more power
that remains. Four bars: fully charged. No
Battery status bars: immediate charging needed. When
charging the phone, the icon will scroll
through the bars until the battery is fully
charged.
GPRS services have been activated on your
GPRS network
SIM card.
Shows that an SMS/MMS message is being
received or that there are unread messages.
If the icon
appears in red, this indicates
Message
that the SIM card's text message memory is
full. For information about the message
function, see page 46, "Messages Menu".
You've got a WAP message (this icon will
WAP message only appear when there are no incoming or
unread SMS/MMS messages).
Indicates that you have voicemail messages
Voicemail
Alarm
(this icon will only appear if the function is
supported by your network operator).
The alarm is turned on. To set the alarm, go
to the menu Tools → Alarm. See page 84.
Shows the number of the line currently in
use. To set the line, go to the menu Settings
→ Call Settings → Active Line. For details,
see page 114.
Line in use
Vibrate
In the standby screen, press and hold
to activate the silent profile. See page 38,
"Using the Silent Profile".
10
Getting to Know Your Phone
Icon
Function
Description
Shows that the Normal profile is in use. To
set the operating mode, go to the menu
Settings → Profiles. See page 105.
Normal
Meeting
Outdoors
Personal
Handsfree
Shows that the Meeting profile is in use.
Shows that the Outdoors profile is in use.
Shows that the Personal profile is in use.
Shows that the Handsfree profile is in use.
Shows that the call divert function is active.
To make settings for this function, go to the
menu Settings → Call Settings → Call
Divert. See page 111.
Divert
Roaming has been activated (not your
regular network)
Roaming
Getting to Know Your Phone
11
Using the Keys in the Standby Mode
8
In this user manual, "long-press" means to press and hold down a key
for about two seconds before release. "Press" means to press a key
and release immediately.
8
The chart below is meant only to introduce the commands accessible
with keys when the phone is in standby mode. For information on
other key commands available in other operating modes, see the
pertinent sections in this user manual.
Function keys
•When any key is pressed, the phone will provide aural feedback
through keypad tones. To activate or cancel this aural feedback,
/
enter the menu Settings → Profiles. Scroll to the profile currently
in use and press
(Edit). Then select Keypad Tone. You can
also go to Settings → Audio → Keypad Tone to turn the aural
feedback on or off. See page 107 and page 110.
Key
Commands and functions
Power on/off key
•Long-press to turn the phone on or off.
•Press this key to reject incoming calls or cancel a call
being dialed.
Send/Answer key
•Press to send or answer a call.
•Long-press and your phone will automatically call the
last number dialed.
•Press to access the list of last missed/dialed/received
calls.
OK key
•Press to open up the main menu and show its first item.
12
Getting to Know Your Phone
Key
Commands and functions
Left soft key
•Press to access the Phone Book (when PBook is
shown).
•Press to save the phone number keyed in from the
standby screen to the Phone Book (when Save is
shown).
Right soft key
•
Press this key to use the camera function (when
Camera is shown).
•Press this key to delete entered digits one by one; long-
press to delete all digits entered (when Clear is shown).
•Long-press to turn the silent profile on or off.
Scroll key
•Press
to enter the Quick Access menu. For
information about the Quick Access menu, see page 42.
•Press
to retrieve photos stored in the Album menu.
to enter the Messages menu. For
•Press
a
description of the Messages menu, see page 46.
•Press
to select the profile to activate.
Asterisk key
•Press this key to enter an asterisk " * ".
•To make an international call, long-press this key until
the display shows "+" ,Then enter the recipient's country
code, area code and phone number.
Voicemail key
•Long-press to dial your voicemail number.
Getting to Know Your Phone
13
Key
Commands and functions
# key
•Press to enter "#".
•For extensions: After entering a phone number, long-
press to enter a "P" and then enter the extension
number.
Alphanumeric keys
•Press to enter digits in a phone number.
~
•Shortcut key: Long-press a key to immediately access
the function, or dial the number, that it represents. See
page 42, "Shortcuts Menu".
Alphanumeric keys
Key
Digit
Key
Digit/Symbol/Function
1
7
2
3
8
9
4
5
6
0
* + (long-press)
# P(long-press after entering
a phone number)
8
Long-pressing an alphanumeric key will access the function it
represents, or dial the number that has been assigned to it (shortcut
function).
14
Getting to Know Your Phone
Menu Navigation
When the phone is in standby mode, press
to bring up the main
menu and highlight the first item in that menu: Phone Book.
8
For details on how to use the various functions listed in the menu, see
page 70, "Menus".
Main menu
The main menu
item to which you
have scrolled will
be displayed as an
animation.
Each icon
represents a
sub-menu.
The name of the
main menu item
you have scrolled
to.
Indicates that
pressing
will return the
display to the
standby screen.
Getting to Know Your Phone
15
Sub-menus
The highlighted
row is the currently
selected item.
The name of the
current menu.
Press
to
enter the
highlighted menu
item for editing.
Press
return to the
previous menu
or screen.
to
Press
to enter the sub-menu
represented by highlighted item or
to activate the highlighted
function. Press
to scroll up
or down to an item.
Pop-up menus
Press
to enter the
highlighted
activate the function
represented by the item.
item
or
Press
to
close a pop-up
menu.
Press
to scroll up or
down to an item.
16
Getting to Know Your Phone
Menu navigation example
The example given below demonstrates how to use menus to change the
language setting.
Regular access
1.In the standby mode, press
or to open the main
menu.
2.In the main menu, press
to scroll to the Settings menu
icon. Press
menu.
to enter this
3.In the Settings menu, press
to scroll to the Language
item, then press
to enter
the Language menu.
Getting to Know Your Phone
17
4.Press
language you wish to use.
Then press to confirm
to scroll to the
your selection. If, for example,
you wish to set English as the
display language, scroll to
highlight English, and then
press
. The display will
automatically return to the
Settings menu, displayed in
English.
5.Press
or press
(Back) repeatedly
once to return
to the standby screen.
18
Getting to Know Your Phone
Access through number shortcuts
1.In the standby mode, press
or to bring up the main
menu.
2.The location of items in the
main menu corresponds to
the position of the
keys in the
to
alphanumeric keypad. Thus,
pressing will bring up
the Settings menu.
3.In the Settings menu, the
alphanumeric keys
to
represent menu items 1
to 10. Since Language is item
number 10 in the Settings
menu, pressing
will
bring up the Language sub-
menu.
Getting to Know Your Phone
19
4.Press
language you wish to use.
Then press to confirm
to scroll to the
your selection. If, for example,
you wish to set English as the
display language, scroll to
highlight English, and then
press
. The display will
automatically return to the
Settings menu, displayed in
English.
5.Press
or press
(Back) repeatedly
once to return
to the standby screen.
20
Getting to Know Your Phone
Main menu map
Find
Add
Edit
Phone book
Missed Calls
Received Calls
Dialed Calls
Cleanup All
Call Duration
Call Cost
Copy
Delete
Caller Group
Business card
My Number
Memory Status
Call Records
SMS
MMS
SMS Chat
Voicemail
Cell Broadbast
Memory Status
Messages
Game
Cherry Boy
Eda Mouse
Camera
Camera View Finder
Album
Image
Melody
Cleanup All
Media Center
Alarm
World Clock
Calendar
Memory Status
Tools
Shortcuts
Calculator
Currency Converter
Stopwatch
Date& Time
Auto Power On/Off
Profiles
Oper. Service
WAP Service
STK
Display
Audio
Call Settings
Network
Security
Settings
Power Saving Mode
Language
Input
Restore
Getting to Know Your Phone
21
Using Your Phone
Making a Phone Call
To make a phone call, check your phone is powered on showing the idle
screen. Enter the desired number using the alphanumeric keys
. Press to dial your call.
to
During a call, you can use the options. See page 35, "In-Call Menu".
/
To modify a phone number that you have entered, press
(Clear) to
to delete
delete individual digits. Long-press (Clear) or press
all digits entered and return to the standby screen.
Ending a Phone Call
Press
to end a call. The display will show the total call time, and
then return to the standby screen.
To cancel a call that is being dialed, press
.
/
8
If you also have a call waiting or on hold, after you press
, the
display will show a menu to allow you to choose the call you wish to
end.
22
Using Your Phone
Answering a Phone Call
When a call is received, your phone rings or vibrates, with the display
showing the caller's number (if supported by your network vendor). If
the caller is a contact stored in the Phone Book, the phone will show the
name recorded in the Phone Book.
•If the caller is a member of a caller group, the ring tone assigned to
this group will sound. The display will show the image ID that is
associated with this group as well, to help you identify the caller.
/
•For information on how to set up caller groups in the Phone Book,
see page 26, "Adding Contacts to the Phone Book".
8
If you wish to change the answering mode so that you can press any
key to answer a call, go the menu Settings → Profiles. After
selecting the currently active profile, press
(Edit) and go to
Answer Mode → Any Key.
Rejecting an Incoming Call
• Press
to reject the incoming call.
Making an International Call
1. Enter the outgoing international call code, or long-press
until
"+" appears on the display.
2. Enter the recipient's country code, area code and phone number.
Dial the call by pressing
.
Using Your Phone
23
Making an Emergency Call
To call emergency services, enter 112 (the international emergency
number) and then press to dial the call. You can make an
emergency call even if your phone is locked or cannot access your
network, or there is no SIM card inserted, so long as you are within
range of a network of the type supported by your phone.
Dialing an Extension Number
After you enter a telephone number, long-press
, The phone
display will show "P". At this point, you can enter the desired extension
number, and then press
to dial it.
Speed Dialing
8
You must assign a number key as the shortcut for a particular phone
number in order to use speed dialing for that phone number. For
information on how to set up a shortcut, see page 42, "Shortcuts
Menu".
After you have assigned a number key to serve as the shortcut key for a
particular phone number, you can long-press this key when the phone
is in the standby mode to dial the corresponding phone number. For
example, if you have selected
phone number, long-pressing
as the shortcut key for a certain
will dial this number.
24
Using Your Phone
Listening to Voicemails
When your voicemail inbox contains new messages, your network
vendor will send you a text message to inform you of a new voicemail
message (if the network vendor supports it, the voicemail icon
will
appear on the LCD display). There are two ways to access and listen to
voicemail:
1. When the phone is in standby mode, long press
to directly dial
the voicemail phone number and listen to your voicemail messages.
2. Go to the menu Messages → Voicemail → Get Voicemail to dial the
voicemail number.
8
If the voicemail number is not stored on your SIM card or in the phone
itself, you will not be able to access your voicemail by long-pressing
. Generally speaking, network operators will store the voicemail
number on a SIM card before giving it to you. If so, you will be able to
dial your voicemail number by long-pressing
when the phone is
in standby mode, without needing to manually store this number. If
however your network vendor did not store the number on your SIM
card, you will need to do this yourself. To save or modify a voicemail
phone number, go to the menu Messages → Voicemail → Set
Number.
Using Your Phone
25
Phone Book
Adding Contacts to the Phone Book
The Phone Book will have different formats and data headings
depending on whether you have chosen to use a phone book stored on
your SIM card or in your phone's memory. The phone book in your
phone's memory can store up to 500 contacts. The capacity of a phone
book on your SIM card depends on the particular service provided by
your network vendor.
Phone Book in the phone's memory
1. In the standby screen, enter the phone number you
wish to store, and then press
(Save). The
display will show the default data fields for a new
contact.
2. In the contact data screen, scroll to the data field
that you wish to edit, and then press
(Options) to bring up a pop-up menu. You can then
use the following options with the contact data:
• Save: Save the entries you have entered.
• Change Type: Change the category of the phone
number (for example, from Mobile Number to
Home Number). This option can only be used in the
phone number data field.
• Add New Field: Adds other data fields for a contact.
• Delete Field: Removes the selected data field.
3. After completing the data for the various fields, you must press
(Options) and then select Save in order for the contact's data to be
stored in the Phone Book.
26
Using Your Phone
8
8
If you do not wish to save a modified Phone Book record, press
or (Back) to abort.
You can also add a new contact by going to the menu Phone Book
→ Add.
• The default data fields for a contact are as follows:
The contact's name.
The contact's mobile phone number.
The contact's home phone number.
Used to assign a contact to a caller group. Press
to select a
group, and then press
.
Used to set a ring tone for the contact. When there is an incoming
call from the contact, the phone will play this ring tone.
8
A ring tone set in this field will replace the one associated
with the contact's caller group, if any.
Used to set the photo that will appear on the phone's display when
there is an incoming call from the contact.
8
The photo set in this field will replace the image associated
with the contact's caller group, if any.
Using Your Phone
27
• In addition to the contact data fields described above, you can also
add the data fields listed below by pressing
selecting Add New Field.
(Option) and then
The contact's mobile phone number.
The contact's home phone number.
The contact's office phone number.
Other phone number for the contact.
The contact's email address.
The contact's home address.
The contact's office address.
The contact's company name.
The contact's department name.
The contact's job title.
Used for notes about the contact.
28
Using Your Phone
SIM Card Phone Book
In the standby mode, press
(PBook) and then press
(Option), select Add. The Add function will prompt you to select
from To SIM or To Phone. Select To SIM here to add a contact to your
SIM card.
The data fields provided by a SIM card phone book are as follows:
The contact's name.
The contact's mobile phone number.
Used to select a caller group for the contact. Press
to select a
group and then press . When there is an incoming call from this
contact, the ring tone assigned to this group will sound and the
display will show the animation/image associated with the group.
8
8
To set a ring tone and animation/image for each caller group,
go to the menu Phone Book → Caller Group. See page 71.
You can also go the menu Phone Book → Caller Group to
set a caller group for a contact.
Using Your Phone
29
Finding Contacts in the Phone Book
In the standby mode, press
(PBook) to
display contacts stored in the Phone Book.
There are two ways to locate a specific contact in the Phone Book:
• Press
to scroll through the names (listed in alphabetical order)
until the one you want is highlighted.
• Press the alphanumeric key that corresponds to the first letter of the
name you wish to locate the appropriate number of times. For
instance, if the name starts with "K", you would press
"K". The names starting with "K" will appear, with the first one
highlighted. Press to scroll to the name you want.
twice for
8
You can also go to the menu Phone Book → Find, and then enter
the full name or the first letter of the name to locate a contact.
When the desired contact's name is highlighted, you can do one of the
following:
• Press
to dial the first phone number saved in that contact.
• Press
(Option) to bring up a pop-up menu, which contains the
following items:
„ Add: Add a new contact to the phone book.
„ Edit: Edit the Phone Book data for this contact. When you are
finished, press
26.
. For more information on editing, see page
8
If you do not wish to save a modified Phone Book record, press
(Back) or to abort.
30
Using Your Phone
„ Copy to SIM (Phone): If you are currently using a phone book
stored in the phone's memory, you can copy the contact's data to
the phone book stored on your SIM card. Conversely, if you are
currently using a phone book stored on your SIM card, you can
copy the contact's data to the phone book stored in the phone's
memory.
8
The only information that can be copied from a phone book
stored in the phone's memory to the one on your SIM card is a
contact's name, phone number, and caller group. If a contact has
more than one phone number associated with it, when that
contact's data is copied from the phone to the SIM card's phone
book, each phone number will be stored as separate contact.
„ Delete: Erases the contact's data from the Phone Book.
„ Send vCard: Attaches the contact's data to a message and send it
to others.
• Press
to show the information in all data fields
for that contact. You can then perform the following
tasks:
„ Scroll to the number that you wish to dial, and then press
.
„ Scroll to the desired data field. If the complete contents cannot be
displayed on the screen, or there is no content to display (for
example, Note
), press
to display the complete contents
(if the data field is for a voice dialing prompt
, you can press
to play the sound of this voice dialing prompt.
„ Press
following items:
• Add: Add a new contact to the phone book.
(Option) to bring up a pop-up menu that contains the
Using Your Phone
31
• Edit: Used to edit the Phone Book data for this contact. For
information on editing, see page 26.
8
If you do not wish to save a modified Phone Book record,
press or (Back) to abort.
• Copy to SIM (Phone): If you are currently using a phone
book stored in the phone's memory, you can copy the
contact's data to the phone book stored on your SIM card.
Conversely, if you are currently using a phone book stored on
your SIM card, you can copy the contact's data to the phone
book stored in the phone's memory.
• Delete: Erases the contact's data from the Phone Book.
• Call: Dial the currently highlighted number.
• Send Msg.: Send a message (SMS or MMS) to the current
highlighted number.
• Send vCard: Attaches the contact's data to a message and
send to others.
Last Missed, Dialed, and Received Calls
There are two ways you can view the last missed, dialed, and received
calls on your phone, as well as information on their date and time:
1. If there have been any missed calls, the display will show a missed call
message along with the number of calls that were missed.
Press
(View), and then press
to scroll to the desired phone
number.
2. In the standby mode, press
to view the list of the most recent
missed, dialed, and received calls. Press
phone number.
to scroll to the desired
32
Using Your Phone
8
The icon
will appear beside missed calls; the icon
will
appear beside dialed calls; the
calls.
will appear beside received
8
8
If a phone number has already been stored in the information for a
contact in the Phone Book, the display will show the name of this
contact.
If a call for the same number has been missed, dialed, or received
two or more times, a note such as "x02" will appear beside the record
of the call to show the number of times it was missed, dialed, or
received.
8
If your network operator is not able to display a certain call's number,
the list will not show a number for the call.
When the number for a missed, dialed, or received call is highlighted,
you can perform the following tasks:
• Press
to re-dial the number.
• Press
(Option) to bring up a pop-up menu:
„ Save (Edit): If the phone number for the call has not been stored
in the Phone Book, select the Save option to create a contact for
this number in the Phone Book. If this phone number is already
stored under a contact in the Phone Book, select the Edit option
to edit this information for this contact. For information about
editing Phone Book data, see page 26, "Adding Contacts to the
Phone Book".
„ Delete: Erases the record of the call from the list.
„ Call: Dial the phone number.
„ Send Msg.: Send a message to this phone number.
„ Delete All: Erase all the call records.
• Press
time.
to display the details on this call such as caller's name and
Using Your Phone
33
Operations During a Call
8
The following options marked with an asterisk (*) are dependent on
network support and may require a subscription.
Mute
Press
(Mute) to turn off the microphone. The person on the
other end of the line will not be able to hear your voice. To restore the
microphone's function, press
(Unmute).
Putting a Call on Hold*
1. When the only call is active:
a. Press
b. Press
(Hold) to hold this call.
to end this call.
2. When the only call is on hold:
a. Press
b. Press
(Unhold) to resume the call.
to end this call.
3. When there is an active call and a call on hold.
a. Press (Swap) to resume the call that is on hold, and
put the active call on hold.
b. Press
end.
to show on the display a list of calls that you can
Making a Second Call*
Enter a phone number, or select one from the phone number or call
record, and then press
to dial it. The currently active call will
automatically be placed on hold. However, if there is already one active
call and another on hold, this action will fail.
34
Using Your Phone
Call Waiting*
If there is an incoming call while you are on the phone, a tone will
sound through the earpiece and the display will show that a second call
is currently waiting. You can handle the waiting call and currently active
call in the following ways:
1. Answer the waiting call: Press
automatically be placed on hold. However, if there is already another
call on hold, a menu will appear on the display allowing you to select
a call to end and then answer the waiting call.
2. Reject the waiting call: Press
or
(End). Pressing
will bring
(End) will immediately reject the waiting call; pressing
up a menu on the display that you can use to select a call to end.
In-Call Menu
If you press
during a call, it will bring up the call menu. Press
to scroll to the desired item (press
to scroll through the menu page
by page) and then press
to enter that item; press
(Back) to
return to the pervious menu; press
menu.
to return directly to the call
8
Items marked with an asterisk (*) depend on network support and
may require a subscription.
Phone Book
Accesses data in the Phone Book. For details, see page 26, "Phone
Book".
Using Your Phone
35
Call Records
Allows you to view information on missed, received, and dialed calls.
See page 32, "Last Missed, Dialed, and Received Calls".
Conference*
Conference calls allow you to converse with more than one party at a
time. The conference menu contains the following options:
8
The maximum number of parties that can be accommodated during a
conference call depends on the particular service provided by a
network vendor.
Hold/Unhold/Swap*
Toggles the call status.
Join/Private
Adds a party that is on hold to the current conference call, or
isolates a single party in a conference call and puts all other parties
on hold.
Forward
Allows two parties to connect, while ending one's own call (one of
the two parties may be involved in an active call while the other is
either on hold or being dialed), so as to allow the two parties to
have their own call.
Send DTMF
When the phone is connected with other devices or services, you can
send DTMF (Dual Tone Modulation Frequency) strings. DTMF strings
are keypad tones that can be sent via the microphone as you dial
another number. Your phone will emit the tones in order to
communicate with answering machines, pagers, computerized
telephone services, and so forth.
36
Using Your Phone
Enter the phone number and then press
to send the DTMF string.
End Call
End All
Ends all calls, whether active or on hold.
End Active
Ends only the active call.
End Hold
Ends only a call or calls on hold.
End One
Ends only a single call.
Hold/Unhold/Swap
Toggles the call status.
Mute/Unmute
Activates/cancels the silent mode.
Messages
Enters the SMS (Short Message Service — i.e. text message) menu. For
details on the SMS menu, see page 46, "Messages Menu".
Calculator
Allows you to use the calculator. For information about the calculator,
see page 88.
Using Your Phone
37
Using the Silent Profile
From the standby screen, you can long-press
to activate the Silent
profile. Once it is activated, the phone will alert you to an incoming call
by vibrating with no ring tone.
• When you long-press
to activate the Silent profile, the phone
will appear in the LCD
will vibrate for one second. The icon
display's status bar (the external display will show
you that your phone is currently using the Silent profile.
) to remind
• To cancel the Silent profile and restore the previously active vibrant
and ring tone settings, long-press
.
This feature is very convenient for switching to the Silent profile
during, say, a meeting to avoid the disruption caused by a ring tone.
/
8
To set and select a profile, please enter the main menu's Settings →
Profiles. See page 105.
38
Using Your Phone
Camera Function
You can take photos using your phone's embedded camera, and then set
photos as wallpapers for the LCD display's standby screen, or send them
to others through MMS.
1. From the standby screen, press
the view finder.
(Camera), which will bring up
2. Press
(Option) to make the following settings for the camera:
• Resolution: Sets the desired resolution for photographing. You
have the following resolution values to choose from:
Option
High
Represented Resolution
352 x 288
Medium
Low
176 x 144
80 x 72
• Scene: Base on the light conditions of the environment selected,
the camera will automatically adjust its color balance in order for
you to take best-quality pictures.
• Effect: Enables you to apply a special effect to your image to
create an artistic style.
• Free Space: Shows the amount of remaining available memory for
storing photos.
3. In the view finder, press
to bring up the resolution and scene
status bar. Press to hide the status bar. The number at the top
right corner of the screen indicates the number of photos available to
be taken. You will find the following icons on the status bar:
Using Your Phone
39
Scene was set to Automatic.
Scene was set to Indoors.
Scene was set to Outdoors.
Scene was set to Night.
One filled star indicates that Low resolution was chosen.
Two filled stars indicate that Medium resolution was chosen.
Three filled stars indicate that High resolution was chosen.
You can also use the camera by going to the menu: Camera.
/
4. After you have completed necessary camera settings, press
to
photograph the object when it is in focus. Its photo will then show up
on the LCD display.
Please note the following while shooting photos
•The external camera does not have a flash. Please take photos in a
well-lit area.
•When taking photos, do not block or touch the camera lens on the
back of the phone.
•Always photograph your object with the source of light behind you.
•Do not shake the phone when taking photos.
•Please be sure that the lens is perfectly clean before taking photos.
Use a soft cloth to wipe the lens if it is not clean.
40
Using Your Phone
5. Press
(Save) to save this photo to Media Center → Album. To
(Discard) to take a new one.
take another photo simply press
After you have saved a photo to the phone, you can manage this
photo using the options below:
• Send Photo: Sends the picture in a MMS message.
8
For information about messaging features, see page 46,
"Messages Menu".
• Set Image ID: Set the current selected photo as a phone book
contact's visual caller ID. When there is an incoming call from
that contact, the phone's display will show this photo.
•New Entry: Enables you to create a new contact in the
Phone Book using the photo as her/his caller ID.
•Exist Entry: Associate the current selected photo with a
contact in the phone book entries.
8
This function is only available for contacts saved in the phone
memory's phone book.
• Set Wallpaper: Designates this photo as the wallpaper for the
LCD display's standby screen. You can also do so by using the
menu: Media Center → Album, or by using Settings → Display
→ Wallpaper → Photo.
• Rename: Give this photo a new file name.
8
A photo's name can't be left empty, nor can it share the same
name with another photo already stored in your phone.
• Details: Shows the photo's name, date, resolution, and file size.
Using Your Phone
41
Shortcuts Menu
You can use the Shortcuts menu to assign 8 alphanumeric keys as
shortcuts to commonly used functions or frequently dialed numbers.
The number 1 key has been assigned to voicemail dialing and you are
not allowed to change it.
Entering the Shortcuts Menu
From the standby screen, press
to enter the
Shortcuts menu. The numbers 2 to 9 displayed in the
menu's default screen represent the corresponding 8
alphanumeric keys on the phone.
Setting Function Shortcuts
1. In the Shortcuts menu, press
selection box to the number key you wish to use as
a shortcut key ( is selected in the example
on the right). You can also press the actual
alphanumeric key to select it.
to move the
2. Press
and use
(Option) to bring up a pop-up menu,
to select Add Function. Then press
.
42
Using Your Phone
3. From the Add Function menu, press
to
select the function to be represented by the
shortcut key
,
and then press
.
Alternatively, you can press
a
corresponding
alphanumeric key to select the function you want.
8
The functions listed in the Add Function menu
are selected from various other menus. For
details on these functions, see page 70, "Menus".
4. After
has been set as the function shortcut
key, the '2' icon in the shortcut menu screen will
be replaced by the icon for the function assigned
to
. The top of the screen will display the
name of the function currently assigned to this
key.
5. Repeat the above step to add or modify function
shortcut key assignments.
6. To cancel a shortcut key and restore the key's
original function, use
to move the selection
box to the icon for the shortcut key that you wish
to cancel, and then press
(Option). Select
Delete to cancel the shortcut.
8
If you select Delete All, all shortcut settings will
be cancelled.
Using Your Phone
43
Setting Phone Number Shortcuts
1. The method for setting a phone number shortcut
key is largely the same as for a function shortcut
key. After selecting the shortcut key, press
(Option) to bring up a pop-up menu. After
selecting Add Phone, press
to confirm.
2. From the Phone Book, select a contact, and then
press
.
3. Next, from the list of phone numbers for this
contact, select the one that you wish to access
through the shortcut key, and then press
.
4. After you have set the shortcut key, the number
icon for the key will be replaced by an icon
representing a phone number shortcut. The upper
part of the screen will display the name of the
contact to whom the phone number accessible by
the shortcut key belongs.
44
Using Your Phone
5. Repeat the above step to add or modify a phone
number shortcut.
Different categories of phone
numbers will be represented by
different phone number shortcut
icons.
Using Function and Phone Number Shortcuts
There are two ways to use shortcuts:
1. From the standby screen, long-press
to
to access the
function represented by that key or dial the number it represents.
2. From the standby screen, press
You can then:
to enter the Shortcuts menu.
a. Press
the desired key. Then press
or dial the assigned phone number.
to move the selection box to the icon corresponding to
to access the assigned function
b. Press the corresponding key
to
to access the
function represented by that key or dial the number it represents.
Using Your Phone
45
Messages Menu
Your phone supports various messaging services including SMS (Short
Messaging Service) and MMS (Multimedia Messaging service). SMS
allows you to insert simple animations and ring tones into your short
messages, while MMS enables you to send photos, colored images and
music through your phone. You must have a subscription that supports
MMS. Please contact your service provider for details.
From the standby screen, press
to enter the Messages menu. You
can also press when in the standby screen and then enter from the
main menu by selecting
.
Additional information about messaging
•When a new message is received, or when there are unread messages in
the phone's or SIM card's memory, the LCD display will show the
in its status bar to remind you that you have unread messages.
icon
•When a message has arrived, it will be saved either to the the phone's
memory or to your SIM card's memory, depending on the preferred
memory you have selected in the menu: Messages → SMS → Settings →
Save Msg. to (See page 51).
•If the LCD display shows a red icon
, this means that the SIM card's
message memory is full. When the SIM card's memory is full, your phone
will not be able to receive any new messages. The display will show a
"Message capacity exceed" message.
The items in the Messages menu are as follows:
46
Using Your Phone
SMS
Editing and Sending a New Short Message
1. Go to menu: SMS > New to bring up the message
editor so you can write a new short message. Use the
alphanumeric keys to enter text.
8
For information on how to use the input methods
provided by the phone for writing messages, see
page 64, "Input Modes".
8
If no text has been entered in the editing screen,
press
to return to the standby screen; if some
will bring up
text has been entered, pressing
the prompt "Cancel Message?", to make sure you
wish to abort the message being edited. If you
press
(Yes), you will return to the standby
screen; if you press
writing the message.
(No), you can continue
2. When writing a message, press
following tasks:
(Option) to perform the
• Insert: You can insert the following types of objects:
„ Text: This is a list of templates that can be used instead of
entering all the characters individually. You can use the
factory default templates or templates of your own that you
previously saved to the list.
8
To create your own quick message templates, go the menu
Messages → SMS → Templates. See page 59.
Using Your Phone
47
„ Image: You can select an animation from the image library to
insert into your message. Press to select image you wish
once to preview and then press again to
to insert, press
insert the image.
„ Melody: You can select a ring tone from the melody library to
insert into your message. Scroll to ring tone you desire, and
then press
to insert the ring tone into your message. The
inserted ring tone will be displayed as musical note within the
message's text.
„ vCard: You can select a contact's data from your Phone Book
to attach to your message. After receiving your message, the
recipient can save the attached contact data to their own
Phone Book.
„ vCalendar: You can select a Calendar memo and then attach
it to your message. After receiving your message, the recipient
can save this attached memo to their own Calendar.
• Alignment: Used to select the type of text alignment for the
message's content.
3. After you have finished editing the message, press
following options appear:
and the
• Send: Press
to enter a recipient's phone number editor. You
(Browse) to select
may enter a phone number or press
recipients from the list of contacts in the Phone Book. Follow the
steps below:
a. Press
press
to scroll to the name of contact, and then
to select it. Repeat the step to select multiple
contacts.
b. Press
(Done) to return to the recipient's phone
48
Using Your Phone
number editor.
c. Press to send.
8
When a message is to be sent, a copy of the message will be saved
to the Outbox folder. If the save fails, the "Save to Outbox Failed!"
screen will appear and the send operation will stop.
• Save to Draft: Saves the message to the Drafts folder.
• Discard: Discards the message.
Receiving and Reading a Short Message
1. When you receive a new short message, the phone will play the alert
sound and the message "1 New SMS" along with the sender's name
will appear. If the sender is not stored in the phone book then only
phone number will be shown.
2. Press
(Option) the following options appear:
„ New: Allows you to write and send a new message.
„ Delete: Delete the selected message.
„ Call Sender: Uses the number from which the message was sent
to call the sender.
„ Chat: Starts a chat session with the sender.
„ Forward: Forward the massage to others and you may edit the
content beforehand.
„ Save Sender Info: Save the phone number from which the
message was sent to the Phone Book.
„ Delete All: Delete all messages in the Inbox.
3. Press
to read your message. Then press
(Option) the
following options appear:
„ Reply: Allows you to write and send a reply message.
„ Delete: Deletes the message being read.
„ Call Sender: Uses the number from which the message was sent to
call the sender.
Using Your Phone
49
„ Chat: Starts a chat session with the sender.
„ Forward: Forward the massage to others and you may edit the
content beforehand.
„ Save: Allows you to save the following content:
• Save the phone number from which the message was sent
(the number shown on the display in the "Sender Info" item)
to the Phone Book.
• Save the phone number displayed in the message's contents.
(the option for a directly displayed number).
• If the message has a picture or ring tone attached, you can
save these objects to your phone's memory. Depending on
the type of the object, the phone will save it to the
corresponding category in the Media Center menu.
8
8
8
If you are saving an image or photo, you can select the
Save as Wallpaper option, setting it as the wallpaper for the
standby screen.
If you are saving a melody, you can also select the Save as
Ring Tone option, setting it as the ring tone that will play
when there is an incoming call.
If the message has a contact's information attached to it, you
8 can save that contact's information to your Phone Book.
If the message has a Calendar memo attached to it, you can
8 save that memo to your Calendar.
For details on the Media Center menu, see page 80.
Managing Outbox
Go to menu: SMS > Outbox. This option preserves a backup copy of
messages that you previously sent. Scroll to the massage and then press
(Option) to delete, resend or forward the message. Select Delete
All to erase all messages.
50
Using Your Phone
Managing Drafts
Go to menu: SMS > Drafts. This option allows you to preserve message
drafts that you have saved. Scroll to the desired message record, and then
you can:
• Press
(Option) to delete the draft or to delete all.
to edit the contents of the message.
• Press
Using the SMS Templates
Go to menu: SMS
>
Templates. You can use the quick message
templates in this menu to compose a message without having to enter
the entire text character by character. You can use the factory default
templates, or templates that you previously saved to the list. Scroll to the
desired template and then press
to insert its text into your message.
You can then edit the text as you wish and then send the message.
To create your own quick message templates, press
(Option) and
then select Add. You can then enter the text for the template, pressing
to save it.
8
If a template is one of the factory defaults, you will not be able to use
the editing function to modify it.
Cleaning Up Messages
Go to menu: SMS > Cleanup. This option allows you to cleanup part of
or all of the messages. The options for cleanup includes All, Inbox, All
Read, Outbox, and Drafts.
Settings
Save Msg. to
Here you can determine whether a new message will be saved
to the phone's memory or to your SIM card's memory.
Using Your Phone
51
Service Center No.
This feature allows you to save the message center's phone
number for sending your messages. The messages that you
send are sent to recipients through this message center.
Enter the message number provided by the network vendor.
After you are finished, press
to confirm.
Bearer Mode
This can be set according to whether you are using a GPRS
network system or a regular GSM dialup network. If you are
using a GPRS network, you can use both the GPRS and dialup
network to send and receive SMS messages. If however you are
using a dialup network, you are restricted to using only the
dialup network for sending and receiving SMS messages.
• GPRS: Use only the GPRS network to send and receive SMS
messages.
• CSD: Use only the dialup network to send and receive SMS
messages.
• GPRS Preferred: Use the GPRS network preferentially. Only if
there is no GPRS network present will the dialup network be
used.
• CSD Preferred: Use the dialup network preferentially. Only if
there is no GPRS network will the GPRS network be used.
Validity Period
This sets the duration that an undeliverable SMS message that
you send can be stored at the message center. During this
period, the message center will continue to attempt to deliver
the message to the designated number.
52
Using Your Phone
Message Type
You can request that your network operator convert your text
messages to different types.
Status Report
After activating this function, the network vendor will report
to you when a message has been delivered.
Direct Reply
You can request that your reply to an SMS be sent directly
through the sender's message center.
Using Your Phone
53
MMS
8
Before you start to use MMS, you have to subscribe to both GPRS
and MMS services provided by your operator. Then you have to
adjust MMS settings in your phone to be able to use MMS.
Because MMS uses your operator's MMS server on a GPRS network
to send messages to phones, you need to adjust the following
settings correctly in order to use MMS:
Go to menu: Oper.Service > WAP Service > WAP Setting to create a
new WAP profile for your network settings. See page 97, "WAP Settings"
for details about how to set up a WAP profile.
Go to menu: Message > MMS > Settings > Server Info to select the MMS
server for sending and receiving MMS messages.
8
You should contact your operator for details on MMS settings. Some
operators may adjust the settings for you after you subscribe to MMS.
Editing and Sending MMS Messages
Go to menu: MMS > New, and follow the steps below to write and send
new MMS message.
1. Fill in below fields required for sending a MMS message.
• To: Press
to enter a recipient's phone number editor. You
(Browse) to select
may enter a phone number or press
recipients from the list of contacts in the Phone Book. Follow the
steps below:
a. Press
press
to scroll to the name of contact, and then
to select it. Repeat the step to select multiple
contacts.
b. Press
number editor.
(Done) to return to the recipient's phone
54
Using Your Phone
c. Press
• Subject: press
• Content: press
to send.
to enter the text for the subject.
to enter the slide editor. See below for details
on the options of editing the content.
• Cc: You can send the message as a carbon copy to others.
• Bcc: You can send the message as a confidential carbon copy to
others.
• Priority: press
to set the priority high, normal, or low for this
message.
• Receipt: press
to choose from the following receipt modes:
„ Both Delivery/Read: Asks the recipient to return
confirmation after receiving and reading your message.
a
„ Delivery Only: Asks the recipient to return a confirmation
after receiving your message.
„ Read Only: Asks the recipient to return a confirmation after
reading your message.
„ None: Cancels this function.
2. To edit the MMS message content, scroll to the Content and then press
to enter the slide editor. Press
execute the following tasks:
(Option) you can
• Insert:
„ New Photo: Brings up camera view finder for you to take a
new photo. The photo can then be inserted into the current
MMS slide afterwards.
„ Photo: You can select a photo saved in the Album to insert
into a MMS slide. Press
(Save) to immediately insert
the highlighted photo into current slide, or press
to view
Using Your Phone
55
the highlighted photo. Press
will display the next or
previous photo. Press
slide.
again to save the photo into the
„ Templates: Insert the default MMS templates into your
messages. Those templates contain images and text. You can
customize those by inserting more objects you like.
„ Image: You can select a image saved in the image library to
insert into a MMS slide. Press
(Save) to immediately
insert the highlighted image into current slide, or press
to view the highlighted image.
„ Melody: You can select a ring tone saved in the phone to
insert into a MMS page. Scroll to highlight the file name of
the desired ring tone, and then press
tone to the MMS page.
to insert this ring
8
Each MMS page is only able to accommodate one image and
one audio file. If you insert another image or audio file into the
same page, the newly inserted file will replace the existing one.
„ Text: Enter text templates into your message.
„ Slide Before: Insert a new page before the current one.
„ Slide After: Insert a new page after the current one.
• Preview: Plays all the slides in the message in sequence.
• Remove Melody: Remove the audio file on the current shown
slide.
• Remove Text: Remove the text on the current shown slide.
• Remove Image/Slide: Remove the image if your message contains
only one slide. Remove the current shown slide if your message
contains multiple slides.
• Previous/Next Slide: Going to the previous or next slide.
56
Using Your Phone
• Slide Duration: To set the duration of each slide during playing.
For example, 30 means each slide will played for 30 seconds.
8
Each slide allows only one image and one audio file. If you try to
insert a second image or audio, an Out of range message will
pop up.
3. After you finish all slides for a MMS message, press
and choose from the following options:
(Option)
• Send: Send the message immediately.
• Save to Draft: Store the message in Outbox.
• Preview: Preview the message.
• Discard: Discards the message.
Reading an MMS Message
Having successfully downloaded the MMS message, the display will
automatically switch to Inbox, press to start playing the MMS
again to stop playing. Press
message page by page. Press
(Option) to execute the following taks:
• Reply: Reply to the sender.
• Delete: Delete this message.
• Forward: Forward the message to someone else.
• Save: Save the image shown on the slide or the sender information to
your phone. After you save it, you can go to the menu: Media Center >
Image to see it.
• Save all: Save the audio files and the images attached on the message
to your phone.
Using the MMS Templates
These preset MMS templates contain images and text. Scroll to
highlight the template you like and then press
template into your own MMS message.
to customize that
Using Your Phone
57
Cleaning Up Messages
Go to menu: MMS > Cleanup. This option allows you to cleanup part of
or all of the messages. The options for cleanup includes All, Inbox, All
Read, Outbox, and Drafts.
Settings
Before you start to use MMS, go to menu: MMS > Settings to adjust the
following settings:
Filter
Your phone will reject all MMS messages from the senders
listed here.
Expiry
Sets the length of time your outgoing MMS message stays on
the server before it reaches the recipient successfully.
Reply Type
You can determine here whether you want to use an SMS
message or MMS message in reply to an MMS message you
have received.
Size Limit
Sets the maximum size for a message that the phone receives. If
an incoming message exceeds this size, the phone will not be
able to download that message.
Server Info
Activates the MMS server used for sending and receiving MMS
messages.
58
Using Your Phone
Deferred Download
After you activate this function, the phone will only download
the information associated with the sender when it receives an
MMS message. You can then decide whether to download this
message's content after you have read the information related
to the sender.
Delivery Report
Asks the recipient to return a confirmation after receiving your
MMS message.
Read Report
Asks the recipient to return a confirmation after reading your
message.
SMS Chat
You can engage in a peer-to-peer chat session by writing short messages
to another mobile phone user. This feature allows you to have a
continuous text conversation with someone without having to enter the
number of the recipient each time you have something new to say. The
text conversation is recorded so you can review what has been said in
the chat session.
Starting a chat session
There are two ways of initiating a chat session.
1. Go to: SMS Chat →Start Chat to start a new chat session. Follow
the steps below to conduct the chat:
a.Enter the nickname for the chat session, and press
b.Enter the phone number of the person you want to chat with.
c.Write your message. When you finish, press to send the
message to invite the recipient to a chat. The chat log shows
.
Using Your Phone
59
your nickname followed by your message as “nickname>
message”.
d.When the chat message is sent, press
(Option) and then
choose Send to enter another message. The message will
automatically be sent to the same recipient. Repeat the same
process to send more messages to the same person.
2. Alternatively, to start a chat session, you can select a message from
Inbox, press
(Option) and then choose Chat. Select a chat
. Write your
to send the message to invite the recipient
partner from the Nickname list and then press
message and press
to a chat.
Receiving a reply to your chat message
When your phone receives a reply from your chat partner, the chat
log will show your partner’s name and message, followed by the
previous message(s) you sent. You can now begin to chat with your
partner.
Receiving a request for a new chat
When your phone receives a chat request from another person, a
dialogue box would pop up on the display asking if you want to join
the chat. Follow the steps below to reply to the chat message:
1. Press
2. Press
press
to view the chat message.
to join the chat. Enter your nickname and message, and
to send your message.
60
Using Your Phone
Leaving a chat session
If you want to leave a chat session, press
(back) or
. This
will take you back to the SMS Chat menu. You phone will keep the
records of the last chat session. To resume the previous chat session,
scroll to select Previous Chat. If you want to start a new chat, go to:
SMS Chat →New Chat.
When you are interrupted by an incoming call during a
chat session
1. Answer the call. Upon ending the call, the display returns to the
idle mode. Then you may resume the chat session by selecting
Previous Chat from the SMS Chat menu.
2. Reject the incoming call and continue the chat by selecting
Previous Chat from the SMS Chat menu.
Voicemail
Get Voicemail
Used to dial the voicemail number provided by your network
vendor to listen to your voicemails.
Set Number
You can save your voicemail phone number here.
8
Your network vendor will provide you with your voicemail inbox
number and a number for accessing any other voicemail services.
For detailed information about voicemail services, contact your
network operator to see if you need to save a specific phone number
to your phone in order to access your voicemail inbox.
Using Your Phone
61
Cell Broadcast
Cell broadcast messages are general messages that your network
operator broadcasts to all phones within a particular area. These
messages are broadcast in numbered channels. For example, channel
030 might be for local weather, 060 for traffic reports, 080 for
information about local hospitals, taxis, pharmacies, and so forth.
You can receive cell broadcast messages that your network operator
broadcasts, and select your preferred topics and languages.
8
8
For more information about available channels and a list of the
information they provide, contact your network operator.
When you receive a cell broadcast, the content will be displayed twice
in ticker-tape fashion.
Receive
Allows you to select whether or not to receive cell broadcast
messages.
Topics
Allows you to decide what information you wish to receive
from your network operator's cell broadcasts. The topics listed
in the Topics list represent the broadcast information that you
have selected to receive from your network operator.
If you have not previously saved any topics, you can press
(Option) and then select the Add option so that you can
enter the desired range of topic numbers (that is, the channel
numbers). The upper and lower limits of the range are the
highest and lowest channel numbers, respectively. The largest
62
Using Your Phone
possible range is 0 to 65534. You are no longer limited to
selecting only single channels, but can specify a range. After the
list has stored the topic range, you can select a specific topic
and then press
(Option) to add it to the list. You can also
edit or delete selected topics.
Language
You can limit the cell broadcast information that you receive
from your network operator to
a
specific language.
Press
press
(Select) to select your preferred language, and then
.
Memory Status
Displays the amount of remaining available memory, including
pictures, animations and ring tones stored on the phone.
Using Your Phone
63
Input Modes
Changing the Text Input Mode
The text input mode
currently in use
When the display shows the editing screen, you
will be able to see the name of the current text
input mode in the upper right corner of the
screen. Press
to change the input mode.
The input mode icons (names) that may appear in the upper right
corner of the screen represent the following input modes:
Uppercase letters input mode.
Lowercase letters input mode.
iTap (predictive input mode) for uppercase letters.
iTap (predictive input mode) for lowercase letters.
Numeric input mode (123).
You can set the default input mode to the one you most frequently
/
use. Go the menu Settings → Input Mode. See page 119.
64
Using Your Phone
Letter Input Mode (ABC)
In this mode, press the key containing the desired letter repeatedly to
scroll through the available characters in order until it is reached.
How to use the letter input mode
• You must press the key corresponding to the desired letter the correct
number of times in order to enter the letter you want. Display letters
for entry according to the order shown on each key. Pressing a key
once will display the first letter listed on the key, while pressing it twice
will display the second letter, and so on.
• When you have entered a letter and wish to enter the next letter, either
wait for two seconds until the cursor moves to the next text entry
position, or immediately press the key for the next letter.
• Press
• While entering text, press
to move the cursor up or down. Press
to enter a space before beginning a new word.
to move the cursor left or right; press
once to delete a
to delete all entered content.
character; long-press
Numeric Input Mode (123)
The numeric input mode allows you to use the alphanumeric keys
to to enter numbers.
Predictive Input Mode (iTap)
iTap analyzes letters as they being inputted, making intelligent
predictions about the words you are attempting to enter, and speeding
up text entry.
Using Your Phone
65
How to use iTap
• Press once the alphanumeric key corresponding to the first letter of
the word you wish to enter without considering where that letter falls
in the sequence of characters available through that key. Then press
the key corresponding to the second letter, and so forth. The phone
will predict which word you wish to enter based on the set of keys you
have pressed. The predicted word will be shown in the lower left
portion of the screen. This word may change as you continue to press
other keys; therefore, before you have entered a complete word, you
do not need to worry if the displayed word does not yet match the
word you intend to enter.
• After pressing keys for a complete word, if the displayed word does
not match the one you intended to enter, press
candidate words and locate the desired word.
to view other
• Once the correct word is displayed on the screen, press
to enter this
word. A space will automatically be inserted after the word.
• While entering text, press
to move the cursor left or right; press
to move the cursor up or down. Press
once to delete a
character; long-press
to delete all entered text.
Example of iTap in use
To enter "COME HOME" in the message editing screen using iTap, use
the following steps:
1. Press
2. Press
3. Press
to switch to iTap for uppercase letters (ITAP).
to select C, O, M, E.
to enter "COME" as text. A space will automatically be
inserted after "COME".
4. Press
to enter "HOME".
66
Using Your Phone
5. Since "GOOD" is not the word that you wish to enter, press
display the next candidate word, "HOME".
to
6. Press
to place "HOME" into the message.
Symbol Input Mode
When editing messages, press
to open the symbols field along the
to move the selection box to the symbol
to place it in the message text.
bottom of the screen. Use
you wish to enter, and then press
Using Your Phone
67
Direct Connection to URLs
Your phone provides handy preset URL text hotkeys, enabling you to
enter a complete URL more quickly and conveniently, and making
Internet access more efficient and enjoyable.
From the standby screen, you can rapidly key in numerical URLs. If, for
example, you wish to enter "http://123.com" you need only key in "123"
and then press
. The full URL will appear on the screen.
automatically adds the necessary "http://" prefix and the ".com" domain
suffix. To actually connect to this website, simply press to confirm
and the phone's browser will be started up so that you can get online.
When entering a URL, you can also use
functions:
to access the following
• After pressing
once, further presses of
will switch to the URL
suffixes shown in the chart:
Number of
times
Output result
0
1
2
3
4
5
. com
.com.tw
.net
.net.tw
.com.cn
.net.cn
• You can convert
(*) into the (.) that appears in URL addresses.
For example, if you enter 123*456 in the standby screen, and then
press
, the URL "http://123.456.com" will appear on the screen.
68
Using Your Phone
• After you press
to enter "http://" press
to enter "/" and "-".
For example, if after you enter "123" and then press
"http://123.com" to appear on the screen-you press
once-causing
again, the
URL will change to "http://123.com/". Pressing
switch between "/" and "-".
again will
• When the screen shows the desired URL, press
to connect to the
Internet and access this URL address.
Using Your Phone
69
Menus
The phone's menus provide various features. The main menu consists
of 9 icons. Each icon represents a particular menu item, which is used to
access related sub-menus.
For information about navigating menus, see page 15, "Menu
Navigation".
Phone Book
This menu provides various functions for managing the Phone Book,
including the ability to add, locate, and copy contact data; add contacts
to a caller group; and so forth.
Find
Used to locate a contact in the Phone Book. You can enter the full name
of the desired contact, or if you are not sure about the spelling of the
contact's name, simply enter the first letter, and then press
. The
phone will locate all contacts whose names begin with this letter, and
you can scroll to the field containing the contact you want. For details
on what to do after locating the desired contact, see page 29, "SIM Card
Phone Book".
Add
Used to add a new contact to the Phone Book. You will be prompted to
select from To SIM or To Phone. Select To SIM the contact will be saved
on your SIM memory, and select To Phone the contact will be saved on
the phone. You can follow the procedure described on page 26, "Adding
Contacts to the Phone Book".
70
Menus
Edit
After selecting a particular contact, you can follow the procedure
described on page 26 for editing the data for this contact.
Copy
If you are using the phone book stored in the phone's memory, you can
copy contact data to the SIM card's phone book, and vice versa. You can
select a contact to copy from one phone book to the other, and copy all
contacts in one phone book to the other by choosing the option All
Phone to SIM (All SIM to Phone).
Delete
Deletes a contact from the Phone Book. You can delete one contact at a
time, or delete all contacts at once.
Caller Group
Caller groups are combinations of phone settings used to identify a
particular group of contacts, such as work colleagues, family members,
or friends. For example, you can associate a ring tone and animation
with one group, and when a member of that group calls, the phone will
use the group's ring tone and display its animation.
The phone provides 5 caller groups: Colleagues, Family, Friends, VIP,
Others.
After you scroll the caller group that you wish to configure, you can
perform the following tasks:
• Press
(Option): Used to select the ring tone or image ID
that will help you identify the caller group to which a particular
caller belongs, or to rename the caller group.
Menus
71
• Press
: Allows you to view a list of all contacts that belong to
the caller group. Press
to highlight the desired contact, and
(Option) to access the following options:
then press
„ Add: Add a contact to the caller group. Press
contact to add, and when finished press
„ Delete: Deletes the selected contact from the contact group.
to select a
.
Business Card
You can use this option to enter your own business card information.
The data fields are as follows:
Your name.
Your mobile phone number.
Your e-mail address.
Your company's address.
Your job title.
Press
to begin entering the text. After you are finished entering the data, press
to return to the previous screen. Press (Option) and select
to scroll to the data field you wish to edit, and then press
Save to save all the business card data, or select Send vCard to send this
business card as an attachment in a short message.
72
Menus
My Number
This option allows you to save your SIM card number and name to your
SIM card's memory.
Press
(Option) and select Add to enter your name and number.
(Option) and then select Save to
When you are finished, press
save your data. If you wish to edit the current name and number, press
(Option) and select Edit to edit the currently selected data.
Memory Status
Shows you the entries that have been stored and the maximum entries
that can be stored, on the SIM and on the phone.
Menus
73
Call Records
8
Your network operator must support this feature in order for you to be
able to use it.
This menu includes a list of your missed calls, dialed calls, and received
calls. Call costs and time are also recorded.
Missed Calls
Shows your most recent missed calls.
Press
to scroll to the missed call that you wish to select. You can
now choose to view, edit, or delete the number for the missed call. The
procedure is the same as that described on page 32, "Last Missed,
Dialed, and Received Calls".
Received Calls
Shows your most recent received calls.
The procedure for using this feature is the same as that described on
page 32, "Last Missed, Dialed, and Received Calls".
Dialed Calls
Shows your most recent dialed calls.
The procedure for using this feature is the same as that described on
page 32, "Last Missed, Dialed, and Received Calls".
Cleanup All
Deletes all call records.
Call Duration
8
This feature is only accessible if supported by your network operator.
Last Call Time
74
Menus
Shows the duration of the last call.
All Calls Time
Shows the total time for all calls.
Received Calls Time
Shows the total time for all received calls.
Dialed Calls Time
Shows the total time for all dialed calls.
Reset
Clears all call time records.
8
You must enter your PIN2 code in order to zero call times.
What is a PIN2 code?
/
•The PIN2 is the second PIN code. Its main use is in controlling
restricted services-for example, call time limits and restricted phone
numbers.
•If the PIN2 code is incorrectly entered three times consecutively, the
PIN2 code will be locked. To unlock the PIN2 code, you will need to
enter the PUK2 code, which you obtain from your network operator.
Call Cost
Last Call Cost
Shows the cost of your last call.
8
Requires the support of the network operator.
All Calls Cost
Shows the total cost of all calls.
8
Requires the support of the network operator.
Menus
75
Reset
Clears all call cost records.
8
Requires entry of the PIN2 code.
Call Cost Limit
Shows the current limit set for total call costs.
Set Call Cost
Allows you to first enter the unit price and a currency for
calculating call costs.
8
Requires entry of the PIN2 code.
Messages
For a description of the features available in the messages menu, see
page 46, "Messages Menu".
76
Menus
Games
Your phone provides a number of exciting games that you can use to
entertain yourself when you have a spare moment.
Games
Cherry Boy
This game contains five levels and in each level the
player has three lives. To pass one level you must
collect all the cherries before time is up, or you
must obtain the key to the next level. If you bump
into a monkey, you lose one life. Press
to
begin a new game. Press
menu item you want.
to scroll to the
Game screen
Number of remaining
lives
Your Score
R e m a i n i n g
time
Number of remaining
treasures
Cherry boy you
are controlling
Monkey or the
enemy in this
game
Cherry or the
treasure in this
game
Menus
77
Game controls
Press
Press
a ladder. Press
or
to move the player left or right.
to move the player up or down on
to pause the game.
or
Press
to split the path so the monkey will fall. The
split will be reconnected in 5 seconds.
78
Menus
Eda Mouse
This game contains eight levels and to pass each
level player has to eliminate the fruit to a certain
amount. You pass one level when your score has
reached a thousand points. To eliminate the fruit,
player has to arrange three identical fruit in a row.
You lose the game when the fruit reach the eda
mouse's head.
Mixed sorts of fruit.
Level
Your score
The vertical dotted line
indicates the path you
aim at the target.
Press
or
to move the eda mouse
left or right.
For example, press
once to collect one apple, and
press twice to collect two apples. You can only collect up
to three and they have to be the same kind.
Press
three times to move the mouse to the right
to release the two apples
by three lines. Then press
that you collected. The apples on the vertical line are now
eliminated.
Menus
79
Camera
The digital camera function you access through the main menu is the
same as pressing
(Camera) from the standby screen. For details
on how to use the camera to take photos, see page 39, "Camera
Function".
Media Center
Album
This album stores the phone's default pictures, as well as images
received in MMS messages, or photos taken using the camera on the
phone.
After entering this menu, the photos will shown as thumbnails on the
left, and on the right side of each thumbnail you will see some details
associate with that photo.
• The date when the photo was taken: Shown as "yyyy.mm.dd".
• The photo's resolution: Shown as "width x height".
• The photo's file size: Shown as "xxx KB".
Steps for handling photos are as follows:
Scroll to the desired picture to access the following options:
• Press
to display this picture. Pressing
will display the next or
previous picture.
• Press (Option) to perform the following tasks with the picture:
„ Delete: Deletes the picture.
80
Menus
„ Set Image ID: Set the current selected photo as a phone book
contact's visual caller ID. When there is an incoming call from
that contact, the phone's display will show this photo.
•New Entry: Enables you to create a new contact in the
Phone Book using the photo as her/his caller ID.
•Exist Entry: Associate the current selected photo with a
contact in the phone book entries.
„ Set Wallpaper: Use the picture as the wallpaper for the standby
screen.
„ Send: Sends the picture in a MMS message.
8
For information about messaging features, see page 46,
"Messages Menu".
„ Rename: Allows you to provide the picture with a new name.
„ Delete All: Deletes all the photos in the album.
„ Details: Shows the name of the photo, the date it was taken, and
the size of the image.
Image
This image library stores the phone's default images, as well as images
received in messages, downloaded through WAP services or using
multimedia communications tools. You may set the image as caller ID
image, or send the image in a short message.
The file formats supported by the phone are BMP, PNG, GIF, JPEG
(progressive or marithmetic-encoded saves not supported), and EMS
picture.
Menus
81
Melody
This ring tone library includes the phone's default ring tones, as well as
ring tones received in messages, or downloaded through WAP services
or using multimedia communications tools.
The phone supports the following music file formats: MIDI, SMAF,
and iMelody.
Scroll to the desired ring tone, and press
following tasks with the ring tone:
(Option) to perform the
„ Set Ring ID: Set the current selected ringtone for a contact. When
there is an incoming call from the contact, the phone will play this
ring tone.
•New Entry: Enables you to create a new contact using the
current selected ringtone.
•Exist Entry: Associate the current selected ringtone with
a contact in the phone book entries.
• Set Ringtone: Makes the ring tone the alert sound for incoming
calls.
• Rename: Allows you to give a new name to the ring tone.
8
The phone's default ring tones cannot be renamed, so they do
not present this option.
• Delete: Deletes user-defined ring tones.
8
The phone's default ring tones cannot be deleted. Only user-
defined ring tones provide this option.
• Send: Sends the ring tone in a message.
8
For information about messaging features, see page 46,
"Messages Menu".
82
Menus
• Details: Displays the name of the ring tone, its file size, and
whether it is a default ring tone, or a file that you have saved or
downloaded yourself (noted as User Defined).
Cleanup All
Deletes all the data stored in the media center.
Memory Status
Displays the amount of remaining available memory, including photos,
images, and ring tones stored on the phone.
Menus
83
Tools
Alarm
If you activate the Alarm Clock feature, when the specified date and
time arrive, the phone will sound the alarm, even if your phone is
turned off.
1. Select the alarm you wish to set and press
.
2. The status of the alarm will appear, press
on or off.
to set the alarm status
3. After your alarm is turned on, setting options appear as shown in the
chart below:
Switch the alarm on or off.
Enter the time when an alarm will go off.
Use
to set the alarm mode:
•Once: Alarm will go off only once.
•Daily: Alarm will go off daily.
•Weekday: Alarm will go off Monday through Friday.
Allows you to select the length of the alarm. Press
desired alarm duration.
to select the
Set the ring tone for the alarm. Press
desired ring tone.
(Set) and then select the
84
Menus
4. Lastly, you must press
(Save)to save all your current Alarm
settings. After completing Alarm settings,
standby screen's status bar.
will appear in the
World Clock
If during travel, you move between time zones, the phone will
automatically adjust the time displayed on the screen based on the time
zone prompts provided by the local network operator so that you always
have access to accurate local time.
On
The time displayed on your phone will be reset automatically
according to the local network operator's time zone prompts.
Off
You phone will display the time you have set, and when you travel
to other time zones, the phone will ignore time zone prompts
issued by the local network operator.
Confirm First
The phone will ask for your confirmation before it resets its time.
Menus
85
Calendar
You can use the Calendar to set up memos for forthcoming events such
as a meeting, an appointment, or a friend's birthday. The Calendar will
also remind you about events you have previously scheduled.
1. When you open the Calendar, the phone will
show the calendar for the current date.
8
If you have not set the current date on your
phone, go the menu Settings → Date & Time.
See page 104 .
When the Calendar is
opened, the current
date will be
In the Calendar screen, press
to move
the red box to the date where you wish
create a memo. You can also press
(Option) and select the Go to Today option.
highlighted by a red
box.
2. When the red box is highlighting the desired date,
press (Option) and select the Add option to
open the memo editor.
3. In the memo editor screen, scroll to the data field you wish to edit,
and then press
, or press alphanumeric keys to begin entering
data. You can enter data in these fields:
Enter the subject for the event.
Enter the start date of the event.
Enter a start time of the event.
86
Menus
Enter the end date of the event.
Enter an end time of the event.
This option allows you to set the time you want the reminder to
remind you about the event. For example, if you want the reminder
to sound 30 minutes before the meeting, chose 30 minutes to set
the reminder to do so.
This option allows you to set the reminder repeatedly to go off.
For example, if a meeting is held every Thursday starting 2004/08/
05, you may select 2004/08/05, and then chose Weekly to set the
reminder to go off on Thursdays beginning with 2003/08/05.
Enter a location for the event.
Enter the names of the participants in the event.
Record any notes about the event.
4. After completing entry of data in each of the fields, you must press
(Save) to save the memo to that date.
Shortcuts
For a description of the features accessible through the Shortcuts menu,
see page 42, "Shortcuts Menu".
Menus
87
Calculator
Entered numbers
and calculation
results will appear
in this field.
Allows you to use the phone as a
calculator. Use
to perform
the mathematical operations
shown on the screen.
Press
to
enter a decimal
point.
8
You can enter numbers up
to a maximum of 8 digits in
length.
Currency Converter
Below is a description of the Currency Converter screen:
1. To set the currencies for conversion, press
(Option) and select
either Currency 1 (to set the currency at the top of the screen) or
Currency 2 (to set the currency at the bottom of the screen), then
press
.
to confirm. After selecting a currency from the list, press
2. Used to set the exchange rate.
Press
(Option) and select Rate Setting, then enter the rate for
converting from Currency
1
to Currency 2. The conversion
calculation result will be displayed in the same line as the bottom
currency on the screen. Use the to view the calculation result.
The calculation can provide precision up to two decimal places.
8
The exchange rate field can accommodate a maximum of five digits
(including decimal digits).
8
Press
to enter a decimal point.
88
Menus
3. After returning to the Currency Converter screen, you can select one
of the currencies and then enter an amount that you wish to convert
into the other currency.
8
You can enter amounts up to six digits long.
4. After pressing
the converted amount will appear in the field for
the other currency.
Stopwatch
1. Press
to start the stopwatch.
2. While the stopwatch is running, you can press
(Split) to save up four elapsed times (such as
in a race). The display will show the saved times in
the lower part of the screen.
8
Pressing
(Back) while the stopwatch is
running will bring up the "Quit?" warning message
(the stopwatch will continue to run). Press
(Yes) to stop the stopwatch or
(No) to return
to the timer screen.
3. Press
to halt the stopwatch.
4. Once the stopwatch is halted, press
stopwatch.
(Reset) to zero the
Menus
89
Oper. Service
Your phone includes a built-in WAP browser, allowing you to use the
phone for mobile Internet connectivity. You can browse the online
services offered by the network operator or ISP, such as information on
financial news, sports, travel, and entertainment. To use the phone to
get online, necessary WAP and GPRS settings must be made in this
menu.
8
You must apply to a network operator for WAP services and complete
WAP and GPRS settings in this menu before you will be able to take
advantage of mobile Internet connectivity. In general, once the
service you have applied for has been activated, the network operator
will automatically transmit the needed settings to your phone. If this is
not the case, you must perform this configuration yourself. For
information about WAP and GPRS services and configuration details,
contact a network operator providing these services.
WAP Ser v ice
Your phone provides the following methods for activating the browser
/
and getting online.
1. From the standby screen, activate the browser and get online by
using the feature that allows you to connect directly to URLs. For
details, see page 68, "Direct Connection to URLs".
2. Activate the browser from the three options in the menu Oper.
Service → WAP Service:
• Start Browser: Starts up the browser and connects to the
homepage.
• WAP Message: Starts up the browser and accesses the WAP
inbox for reading text messages.
• Goto URL: Starts up the browser and connects to the URL that
you enter.
90
Menus
Start Browser
Starts up the browser and connects to the homepage.
Browsing a webpage
Referring to the soft key commands at the bottom of the screen,
press
and
to perform needed tasks while browsing a
webpage. Press
to scroll up or down a webpage. For details on
browsing a webpage, inquire with the network operator providing
WAP services. Your Internet connectivity service will determine the
layout and content of the webpages you view. Depending on the
specifics of your service, they way you browse the Internet on your
phone will differ.
How to close the browser and end the online session
• While online, press
or long-press
.
• If you are already viewing a WAP webpage, long-press
or
from the browser's menu select Exit.
How to display the browser's menu
While viewing a WAP webpage, press
menu. Referring to the soft key commands at the bottom of the
screen, press and to access the various options. Press
to display the browser's
the corresponding alphanumeric keys to directly select an option.
The browser menu contains the following items:
Back
Selecting this option will take you to the page you viewed
previously.
Menus
91
Home
Returns to the home page. To designate a particular page to be
your home page, go to 9 Settings → 1 Homepage.
Exit
Closes the browser and returns you to the main menu screen.
Inbox
When your phone receives a message that can only be viewed
using a WAP browser, you enter this WAP inbox to read the
message.
Bookmarks
You can open the Bookmarks menu and select webpage
bookmarks.
View
Allows you to see the current bookmarks and bookmarks
folders. Scroll to the desired bookmark or bookmarks
folder, and you can:
• Press
(Go) to link to the webpage that the
bookmark represents. If you have selected a bookmarks
folder, select the desired bookmark from within the
folder, and then press
(Go).
• Press (Menu) to display the following options:
„ Details: Displays the bookmark's title and the URL it
represents.
„ Delete: Deletes the bookmark or bookmarks folder.
„ New Bookmark: Creates a new bookmark.
„ New Folder: Creates a new bookmarks folder.
92
Menus
„ Move to Folder: Moves
a
bookmark to the
designated folder.
„ Delete All: Deletes all bookmarks and book-marks
folders.
„ Hotkeys: Allows you set a numerical key as a hotkey
for a bookmark. After completing the setting, you
can press this numerical key to directly link to the
webpage represented by the bookmark.
Mark Site
Adds the current webpage to your bookmarks list.
GoTo URL
Press
(Edit) and enter the URL of the webpage that you
wish to browse, and then scroll to the Go option and press
(Go) to link to that URL.
Save Items
When viewing a webpage, if you discover that it contains an
image that can be downloaded, you can access this option to
save the image to your phone. Subsequently, this image will be
available for use when you are composing messages or
choosing a standby screen wallpaper.
Reload
Reloads the current webpage.
Settings
You can enter this item to making the following settings:
8
For detailed information about the following settings, contact
your ISP.
Menus
93
Homepage
Designates a homepage. When you start up the WAP
browser or if you select Home from the browser's menu,
the screen will display the homepage you designate.
a. Press
(Edit) and then enter the URL of the
webpage that you wish to use as your homepage. (Some
WAP service providers do not allow users to set a
homepage.)
b. Select the Save option to designate the URL you entered
as your homepage. Select Use Default to use the
homepage designated by your WAP service provider.
Scroll Mode
You can select two scrolling modes: Block or Smooth. In
the Block mode, as many words as will fit in a line are
shown for a few seconds, then the next line is shown, and
so on. In the Smooth mode, the content scrolls smoothly
on the screen. You can also adjust the scrolling speed: Fast,
Medium, Slow.
Send Referrer
This option allows you to determine whether the browser
will send an HTTP referrer header.
Key Press Timeout
This option sets the amount of time that the phone waits
during text entry before automatically advancing the
cursor to the next entry position. As long as the same key is
re-pressed within the interval of time set here, it will
continue to cycle through the characters available through
that key.
94
Menus
Set Proxy
Your phone can save the settings for six WAP proxy
servers. You can select one of these proxy settings for use as
a default so that your phone will connect to that proxy
server when you begin an Internet session.
You can also go to the menu Oper. Service → Wap Service
→ Wap Setting to select the server that you wish to
activate. See page 97.
Circuit Prompt
The Circuit Prompt is a message displayed before each
circuit data call is made. It reads, "Circuit is down. Start a
data call?" You can choose to enable or disable this feature.
Security
Secure Prompt
The Secure Prompt message is displayed before you
leave a secure area. It reads, "Entering a non-secure
area. OK?" You can choose to enable or disable this
feature.
Current Certificate
Displays information on the certificate currently in
use.
CA Certificates
Displays information on the built-in certificate. A
certificate is a digital ID issued by a trusted third party
known as a certificate authority (CA). The phone uses
CA certificates to authenticate websites that send
information to the phone.
Menus
95
Authentication
You can decide whether your phone should store your
user name and passwords for websites that require
them. If you allow your phone to authenticate you
automatically, you will not need to re-enter your user
name and password each time you visit the same
website.
Advanced
Restart Browser
Restarts the browser, and automatically returns to the
designated homepage. This feature is provided for
your convenience if network errors occur, allowing
you to restart the browser and re-establish your
Internet connection.
Downloads
If this option is enabled, you will not be able to
download images, background audio, and objects.
View Title Region
You can choose whether or not to have the browser
display webpage titles. You can also set this option so
that titles exceeding a certain length will be split into
separate lines. (The first line of the browser displays a
"G" and a globe image, while the second is the "title
region". The actual webpage content begins on the
third line.)
About…
From here, you can view information about the
version of the browser that you are using.
96
Menus
WAP Message
When you receive a new WAP message, the status bar will show the
icon to remind you that you have an unread WAP message. Starts up
the browser and displays the WAP inbox so you can read WAP
messages.
Goto URL
Enter the URL of the webpage that you wish to browse, and then
scroll to the Go option and press
(Go) to link to that URL.
Resume
Returns to the last webpage you viewed.
WAP S ett ings
In this menu, you can make settings for the WAP servers of six
different network operators, and select the server that you would
like to use when connecting to the Internet.
The first time that you start your phone after inserting a SIM card,
the ISP name of the network operator issuing the SIM card will
appear in this menu's first group of settings. This indicates that
your network operator's WAP server settings will be saved under
the name shown. The phone will activate this group of settings for
use in connecting to the Internet.
To activate another set of WAP server settings, scroll to the group of
settings you wish to use and then press
. The phone will activate
these settings for use in connecting to the Internet.
Menus
97
By scrolling to a particular group of WAP server settings that you
wish to modify, and then pressing (Option), you can create a
new group of settings, edit the settings, or delete the settings.
WAP server settings include the fields listed below. Press
(Edit) to edit the setting in each field. When you are finished with
the settings for all fields, you must press
group of WAP server settings to be saved.
in order for this
• Profile Name: Gives the WAP server settings a name.
• Homepage: Sets the webpage that the browser will link to when it
is started up. After you enter this item, key in the URL for the
webpage that you would like to use as the homepage — for
example, http://wap.yahoo.com.
• IP Address: Enter the IP address used for accessing the mobile
Internet.
• Port: Enter the connection port specified by the network operator
—for example, 9201.
• Bearer Mode: Before connecting to the Internet, you must set this
item according to whether your Internet connection bearer mode
is a GPRS network system or a GSM dialup network. Doing so
will allow you to properly link to the data network to browse WAP
pages, download Java programs, and so forth. If you are using a
GPRS network, you can use both the GPRS and dialup network to
connect to the Internet. If, however, you are using a dialup
network, you are restricted to using only the dialup network to
connect to the Internet.
„ GPRS/CSD: Use the GPRS network preferentially. Only if
there is no GPRS network present will the dialup network be
used.
„ GPRS: Use only the GPRS network.
98
Menus
„ CSD/GPRS: Use the dialup network preferentially. Only if
there is no dialup network will the GPRS network be used.
„ CSD: Use only the dialup network.
A dialup network is a GSM Circuit Switch Data Service (CSD
/
for short). Using a dialup network can be likened to using a
home computer's modem, in that before connecting to the
Internet a number must be dialed. As for GPRS, it like the
LANs used at company, where users do not need to dial a
number to access the network. Regular GSM users who are
not using a GPRS network system can only have a dialup
connection to the Internet.
• GPRS: To modify settings for a GPRS account, press
(Edit)
to edit the settings in each field. GPRS settings include the
following fields:
„ APN: Enter the APN (Access Point Name) assigned by your
network operator.
„ User Name: If needed, enter the user name provided by your
network operator.
„ Password: If needed, enter the account password provided by
your network operator.
• CSD: If you are using a GSM network, you must configure and
activate a CSD account. Press
the following fields:
(Edit) to edit the settings in
„ Dial Number: When you start up the browser to connect to
the Internet, you phone will dial this number. Your telecoms
network operator or ISP will provide this number to you.
„ User Name: This is your user account name, and is provided
by your network operator.
„ Password: The account password provided by the network
provider.
Menus
99
„ Line Type: This is the type of dialup connection. Press
to select.
„ Baud Rate: The default value is 9600, which is the standard
speed for data connections with a GSM mobile phone.
„ Auth
Type: This is information needed for
telecommunications protocol authentication.
Save Items
When viewing a webpage, if you discover that it contains an
image that can be downloaded, you can access this option to
save the image to your phone. Subsequently, this image will be
available for use when you are composing messages or
choosing a standby screen wallpaper.
Reload
Reloads the current webpage.
Settings
You can enter this item to making the following settings:
8
For detailed information about the following settings, contact
your ISP.
Homepage
Designates a homepage. When you start up the WAP
browser or if you select Home from the browser's menu,
the screen will display the homepage you designate.
a. Press
(Edit) and then enter the URL of the
webpage that you wish to use as your homepage. (Some
WAP service providers do not allow users to set a
homepage.)
100
Menus
b. Select the Save option to designate the URL you entered
as your homepage. Select Use Default to use the
homepage designated by your WAP service provider.
Scroll Mode
You can select two scrolling modes: Block or Smooth. In
the Block mode, as many words as will fit in a line are
shown for a few seconds, then the next line is shown, and
so on. In the Smooth mode, the content scrolls smoothly
on the screen. You can also adjust the scrolling speed: Fast,
Medium, Slow.
Send Referrer
This option allows you to determine whether the browser
will send an HTTP referrer header.
Key Press Timeout
This option sets the amount of time that the phone waits
during text entry before automatically advancing the
cursor to the next entry position. As long as the same key is
re-pressed within the interval of time set here, it will
continue to cycle through the characters available through
that key.
Set Proxy
Your phone can save the settings for six WAP proxy
servers. You can select one of these proxy settings for use as
a default so that your phone will connect to that proxy
server when you begin an Internet session.
You can also go to the menu Oper. Service → Wap Service
→ Wap Setting to select the server that you wish to
activate. See page 97.
Menus
101
Circuit Prompt
The Circuit Prompt is a message displayed before each
circuit data call is made. It reads, "Circuit is down. Start a
data call?" You can choose to enable or disable this feature.
Security
Secure Prompt
The Secure Prompt message is displayed before you
leave a secure area. It reads, "Entering a non-secure
area. OK?" You can choose to enable or disable this
feature.
Current Certificate
Displays information on the certificate currently in
use.
CA Certificates
Displays information on the built-in certificate. A
certificate is a digital ID issued by a trusted third party
known as a certificate authority (CA). The phone uses
CA certificates to authenticate websites that send
information to the phone.
Authentication
You can decide whether your phone should store your
user name and passwords for websites that require
them. If you allow your phone to authenticate you
automatically, you will not need to re-enter your user
name and password each time you visit the same
website.
102
Menus
Advanced
Restart Browser
Restarts the browser, and automatically returns to the
designated homepage. This feature is provided for
your convenience if network errors occur, allowing
you to restart the browser and re-establish your
Internet connection.
Downloads
If this option is enabled, you will not be able to
download images, background audio, and objects.
View Title Region
You can choose whether or not to have the browser
display webpage titles. You can also set this option so
that titles exceeding a certain length will be split into
separate lines. (The first line of the browser displays a
"G" and a globe image, while the second is the "title
region". The actual webpage content begins on the
third line.)
About…
From here, you can view information about the
version of the browser that you are using.
Clear Cache
Clears webpage content that the browser temporarily stores in
memory.
Clear URLs
Clears URL strings that the browser temporarily stores in memory.
Menus
103
Settings
Date & Time
Used to set the time and date, as well as the format in which the time
and date will be displayed on the startup screen. Press
settings.
to save the
Date
Enter the date using appropriate number keys.
Time
Enter time using appropriate number keys.
Format
This option is used to decide the format in which the time and date
will appear in the standby screen.
Auto Power On/Off
Designates a time for the phone to be automatically turned on or off. If
this option is activated, the phone will be automatically turned on or off
at the designated time each day.
When riding in an airplane or in any other situation where you cannot
use a mobile phone, remember to deactivate the Power On/Off
option.
Power On
When you see Status Off displays on the screen, press
and
choose the On option, scroll to Time and then enter a time you
wish the phone to be auto turned on.
104
Menus
Power Off
When you see Status Off displays on the screen, press
and
choose the On option, scroll to Time and then enter a time you
wish the phone to be auto turned off.
Profiles
A profile is a group of settings that determine whether the phone will
alert you to incoming calls through a ring tone or a vibrating alert, and
how ring tones in general are used on the phone. These settings allow
the phone's operation to best suit the environment you are in.
1. Press
to scroll to the desired profile and then press
to
activate this profile. You can choose from among the following
profiles:
Normal
This is the default profile. Once this profile is activated, the
LCD display's status bar will show the
icon.
Meeting
The options in this profile have been preset to suit a meeting
environment (for example, only a vibrating alert is used, with
no audible ring tone and no keypad tones). Once this profile is
activated, the LCD display's status bar will show the
icon.
Silent
The options in this profile have been preset for occasions where
silence is required (for example, there will be no audible ring
tone, no keypad tones, and no vibrating alert). Once this
profile is activated, the LCD display's status bar will show the
icon.
Menus
105
Outdoors
The options in this profile have been preset to suit an outdoor
activity (for example, use of the highest ring tone volume,
activation of both ring tone and vibrating alerts, and use of
keypad tones). Once this profile is activated, the LCD display's
status bar will show the
.
Handsfree
This profile is only active when a hands-free kit is attached to
the phone. Once this profile is activated, the LCD display's
status bar will show the
icon.
Airplane
When you are on a plane, you can select this profile to turn off
the phone. Once this profile is activated, the phone will
automatically be powered off, and all alarms will be suspended.
If the phone is turned off by long-pressing
still go off at the appointed times.
, the alarms will
Personal
You can use this profile as a group of custom settings, and
rename the profile if desired. Once this profile is activated, the
LCD display's status bar will show the
icon. If you have
renamed this profile, the new name will replace Personal in the
profiles list.
2. Press
to scroll to the desired profile, and then press
(Edit)
to modify the settings listed below and adjust the profile to suit a
particular environment.
Vibration
Includes the following setting options:
106
Menus
• Ring Only: When there is an incoming call, the phone will
use a ring tone but no vibrating alert.
• Vibrate Only: When there is an incoming call, the phone will
use a vibrating alert but no ring tone.
• Ring & Vibrate: When there is an incoming call, the phone
will use both a vibrating alert and a ring tone.
• Vibrate then Ring: When there is an incoming call, the phone
will first use a vibrating alert and then a ring tone.
Call Ring
Your phone includes various types of ring tone melodies. Scroll
to the desired ring tone, and after one second or so you will be
able to hear that ring tone. Press
to confirm your selection.
Message Tone
The ring tone that your phone uses when a message is received.
Calendar Tone
The ring tone used for Calendar events for which you have set
an alarm.
Keypad Tone
Determines whether keypad tones are played when keys are
pressed.
Ring Volume
Press
to adjust the ring tone volume or
mute the ring tone.
Answer Mode
• Send Key: Allows incoming calls to be answered only by
pressing
.
Menus
107
• Any Key: Allows any key except
to be used to answer an
is used to reject an
incoming call. In this mode,
incoming call, and not to answer.
• Automatic: If the Automatic answer mode is activated, the
phone will ring for five seconds, and then the incoming call
will be automatically answered (only the Handsfree profile
allows this setting).
Rename
Allows you to provide a new name for the profile (only
available for the Personal profile).
Restore
Returns the above settings for the profile to their factory
default values.
8
Requires entry of the phone password, whose default value
is 1234.
Display
Wallpaper
Designates the wallpaper used for the LCD display's standby screen.
Select image or photo and press
to enter the image or photo
library. Scroll to the name of the image or photo that you wish to
use, press
to view the whole image. Press
will display the
next or previous image or photo; Press
selection.
to confirm your
Welcome Message
Used to select and configure the image, photo, music or text that is
displayed when the phone is turned on.
108
Menus
• Image: Press
(Edit) to enter the image library. Only the
image selected in this option will be displayed when the phone is
turned on. After selecting an image, you will need to select the
desired music to be played when the phone is turned on. Select
Silent if you do not wish any music to be played.
• Photo: Follow the same steps as selecting images.
• Text: Press
(Edit) to input the text. Only the text entered
in this option will be displayed when the phone is turned on.
After inputting text, you will need to select the desired music to
be played when the phone is turned on. Select Silent if you do not
wish any music to be played.
• Off: Returns the settings for startup music and animation to their
factory default values.
Personal Banner
Enter the text you wish to be displayed on the standby screen.
Contrast
Press
to adjust the contrast of the screen's
display. Press
to confirm the setting.
Brightness
Press
to adjust the brightness of the phone's display
backlighting. Press
to confirm the setting.
Menus
109
Audio
This menu allows you to set various sounds that the phone uses.
8
Some of the options provided in this menu and the Profiles menu are
identical (for example, Call Ring). Therefore the particular setting that
the phone uses will depend on which menu you last used to make the
setting.
Call Settings
Answer Mode
• Any Key: Allows any key except
to be used to answer an
incoming call. In this mode,
call, and not to answer.
is used to reject an incoming
• Send Key: Allows incoming calls to be answered only by pressing
.
Connect Alert
This feature allows the phone to provide a ring tone or vibrating
alert, or flash the backlighting when the recipient of a call has
answered.
Minute Minder
If you turn this function on, the phone will emit a beep per minute
during a call.
Show Number
You can decide whether or not to display your phone number on
the recipient's phone when you make a call.
On: When you call someone, the recipient's phone will display your
phone number.
110
Menus
Off: Your phone number will not be shown on the recipient's
phone.
8
If this feature is turned off, you may not be able to make phone
calls in certain countries, such as Singapore and China.
Preset: Whether your phone number will be displayed on a
recipient's phone will be determined by the default set by the
network operator.
Call Divert
8
Requires the support of the network operator.
Forward All
Forwards all incoming calls to a designated phone number or
voicemail inbox. When you use this feature, you must enter a
phone number to which to forward incoming calls.
8
After the Forward All mode is activated, the standby screen
will display the icon.
When Busy
The phone will divert incoming calls to another number when
you are in the middle of another call.
No Reply
Forwards incoming calls to another number when you do not
answer.
Not Reachable
Diverts incoming calls when your phone is turned off or
outside network coverage.
Cancel All
Cancels all call divert options.
Menus
111
Call Barring
You can request that your network operator block the dialing or
receiving of certain calls. The call barring services below require the
support of your network operator. To activate or cancel any of the
options below, you must enter the network password provided by
the network operator.
All Outgoing
Blocks dialing of any calls from the phone.
Intl. Out
If this option is activated, no international calls can be made
with your phone.
Intl. Except Home
If this option is activated, your phone can only be used to dial
local calls and calls to your home country from abroad. Other
international calls will be barred.
All Incoming
Rejects all incoming calls.
Incoming When Roaming
If you are in another country (using roaming), activating this
option will cause the phone to reject all incoming calls.
Cancel All
Cancels all call barring settings. You must enter the network
password in order to cancel these settings.
Change Password
You can change the network password, which can be obtained
from the network operator.
112
Menus
Call Waiting
If there is an incoming call when you are in the middle of another
call, the screen will display the number of the incoming call and call
waiting message to alert you. You can activate, cancel, or view the
status of this feature from this menu.
8
You must apply to the network operator for the call waiting
service in order to use this feature.
Auto Redial
If there is no answer at a number you have dialed, the phone will
automatically redial.
Fixed Dialing Number
After this feature is activated, the phone will only be able to dial
numbers on the Fixed Dial Number list. If a number is not on the
list, calls cannot be made to this number.
8
When you activate or cancel this feature, you must enter the
PIN2 code.
If the PIN2 code is entered incorrectly three consecutive times,
the PIN2 code will be locked down. You will need the PUK2 code
to unlock the PIN2 code. Contact your network operator to obtain
the PUK2 code.
Before activating the Fixed Dial Number feature, you must
press (View), then press (Option) and select Add to
create a Fixed Dial Number list. You must enter the PIN2 code, and
then add a new number to your Fixed Dial Number list.
After creating the list, you can view, edit and delete numbers in the
list.
Menus
113
Active Line
This feature allows you to use two different phone numbers on one
phone. You can designate one number for dialing calls, while
accepting incoming calls dialed to both numbers without needing
to use two phones. Select either Line 1 or Line 2. The number you
select (
or
) will appear on the standby screen.
8
This feature requires the support of the network operator.
User Group
User Group
Used to create a closed group of callers based on a service
provided by the network operator. The members of a User
Group can call each other, but cannot conduct calls with
anyone outside the group unless special provisions are made.
This option can be used to select whether or not to activate this
service.
Outside Access
When the User Group service is activated, enabling Outside
Access will allow users in the group to make calls to numbers
outside the group. However, incoming calls will still be
restricted to calls from within the group.
Network
Generally speaking, the choice of the network that your phone uses is
configured automatically. When turned on, the phone will
automatically connect to the network provided by your network
operator, or will automatically connect to the roaming network when
you are outside the coverage of your regular network.
If you wish to change the connection network, this menu will allow you
to select the network you want to use. When outside the coverage of
114
Menus
your regular network in your home country or when abroad, you can
manually select the local network system.
8
Your network operator must be able to support network selection in
order for you to use this feature.
Network Mode
You can choose whether the network selection mode that the phone
will use when it is turned on is automatic or manual.
Automatic: If this option is selected, when outside the coverage of
your regular network, the phone will automatically search for
usable networks.
Manual: If this option is selected, when outside the coverage of
your regular network, the phone will list all the networks of telecom
vendors and allow you to choose.
Available List
Allows you to manually select a network. Your phone will list all the
networks of telecoms vendors so you can choose.
8
Not all networks listed will necessarily be available for use. If you
require further information, contact your network operator.
Band Setting
According to your requirements, you can set an appropriate band
in the GSM network system.
Connection
Used to set whether the phone will also search for a GPRS network
when it is turned on.
• GPRS & GSM: When it is turned on, the phone will search for
available GPRS and GSM networks.
• GSM Only: When it is turned on, the phone will search only for a
GSM network.
Menus
115
Service Tone
Used to set whether the phone will sound when it detects an
available network.
Security
You can use a PIN code, phone password, and SIM card lock
authentication to prevent unauthorized use of the phone.
PIN Code
A PIN (Personal Identification Number) code is a password
provided by a network operator. When PIN code authentication is
activated, it will prevent unauthorized use of the SIM card. Unless
the correct PIN code is entered when the phone is turned on, the
SIM card cannot be used, even if it is inserted in another phone.
If the PIN code is entered incorrectly three consecutive times,
this will cause the SIM card to lock down, and a PUK1 code
provided by the network operator will be required to unlock it.
After unlocking, the PIN code will be automatically set to activate
,
once the phone is turned on.
PIN Code
Used to activate/deactivate or change the PIN Code. Before
changing settings for the PIN Code feature, the previously set
PIN Code must be entered.
If you wish to change the PIN Code, you must press
in
the Enable item to select On, so that you will be able to enter
and confirm the new password.
PIN2 Code
Used to change the PIN2 code. The procedure is the same as for
the PIN Code.
116
Menus
Phone Lock
Activates/deactivates or changes the phone's startup password. The
startup password prevents unauthorized persons from using your
phone. Once the phone's password is activated, the phone will be
locked down when it is turned on unless this password is correctly
entered. If an incorrect password is entered, your phone will remain
locked down, and cannot be unlocked even if the SIM card is
replaced by another one. When the phone is locked, you will only
be able to make emergency calls.
Once the phone password is activated, you must enter the password
each time the phone is turned on in order to unlock the phone
(there is no limit on the number of attempts to enter the phone
password).
The procedure for setting the phone password is the same as for the
PIN Code (the default phone password is 1234).
SIM Lock
Using this feature, you can prevent unauthorized persons from
using your phone with other SIM cards. After you activate the SIM
Lock feature, only the SIM card present when the feature was
activated will be accepted by the phone. If a new SIM card is
inserted in the phone, when the phone is turned on and a PIN code
is entered, the phone will request entry of a SIM Lock password
(there is no limit on the number of attempts to enter the SIM Lock
password.
If the password is entered correctly, the phone will be able to
recognize the new SIM card and use it normally. The next time the
phone is turned on with this SIM card inserted, the phone will not
ask again for you to enter the SIM Lock password.
8
Your phone can recognize a maximum of three different SIM
cards.
Menus
117
Before setting the SIM Lock feature, you must enter the previously
set SIM Lock password (the default SIM Lock password is 1234).
The password must be between 4 and 8 digits in length.
Screen Lock
Used to create a security screensaver. When you
have not performed any tasks with the phone for a
set period of time, the phone will automatically
activate the screensaver shown on the right. To
activate the screen lock, you must first enter the
Screen Lock password that was previously set (the
default password is 1234). Scroll to On and press
(Edit) to set
a different period of inactivity for the screen lock to be activated.
Keypad Lock
Used to create a keypad lock. When you have not performed any
tasks with the keypad for a set period of time, the keypad will be
locked. Scroll to Auto Lock and press
(Edit) to set a different
period of inactivity for the keypad lock to be activated
automatically.
Power Saving Mode
After you activate the power saving mode, keypad and display
backlighting will be turned off, in order to conserve power.
Language
You can select the language that the phone will use to display
information.
118
Menus
Care and Maintenance
Take note of the points noted below to ensure that you are using the
phone properly and to extend the lifespan of the phone.
• Store the phone and its accessories out of the reach of children.
• Keep the phone and accessories dry, and use the phone in
environments where the temperature is between –20°C and 55°C.
High or low temperatures outside this range may damage the phone.
• If possible, do not use or store the phone in excessively dusty or dirty
environments.
• Do not remove the warranty seal on the phone yourself, nor allow an
unauthorized dealer to do so.
• Do not use strong detergents or organic solvents to wipe or clean the
phone.
• If your phone or its accessories are not operating normally, contact an
authorized dealer immediately.
• Use only genuine BenQ accessories such as batteries, battery charger
and hands-free kit to ensure the phone's normal operation and
preserve battery life, as well as protect the safety of your person and
belongings. Use of non-BenQ accessories will not allow your phone to
achieve optimal performance, and may cause the phone to
malfunction. Any malfunctions or damage caused by the use of third-
party accessories are not be covered by the terms of the product
warranty, and will void the product warranty.
• Avoid allowing objects that may discharge electricity to contact the
charging socket on the bottom of the phone or the metal contacts on
the battery, as this may cause short circuits and put you in danger.
120
Care and Maintenance
Troubleshooting
If you encounter problems while using the phone, or if it performs
erratically, you can consult the information in the chart below. If your
particular problem cannot be resolved using the information in the
chart, contact the dealer where you purchased the phone.
Problem
Possible cause
Solution
Move to a location where the
network signal can be
properly received.
•The network signal is too
weak at your current
location — for example, in
a basement or near a tall
building-because wireless
transmissions can not
effectively reach it.
Poor
reception
Avoid using the phone at
such times, or try again after
waiting a short time.
•The network is busy at
the current time (for
example, during peak
times, there may be too
much network traffic to
handle additional calls).
You can request a service
area map from your network
operator.
•You are too far away from
a
base station for your
network operator.
Hang up the phone and dial
again. You may be switched
to a better-quality network
trunk or phone line.
•Poor network trunk quality
on the part of your
network operator.
Echo or noise
•Poor local telephone line
quality.
Troubleshooting
121
Problem
Possible cause
Solution
If you are located in an area
where signaling is weak,
temporarily shut off the
phone.
•The standby time is
related to your network
operator's system
configuration. The same
phone used with different
network operators'
systems will not provide
exactly the same length
of standby time.
Use a new battery.
•The battery is depleted. In
high-temperature
environments, battery life
will be shortened.
Shortened
standby time
Change your location to one
where the network is
accessible, or temporarily
turn off your phone.
•If you are not able to
connect to the network,
the phone will continue to
send out signals as it
attempts to locate a base
station. Doing so
consumes battery power
and will consequently
shorten standby time.
You cannot
switch your
phone on.
Recharge the phone's
battery.
•Battery power has been
depleted.
Take the SIM card to your
network operator for testing.
•SIM card malfunction or
damage.
SIM card
error
Insert the SIM card properly.
•SIM card inserted
improperly.
Use a soft, dry cloth to clean
the SIM card contacts.
•Debris on the SIM card
contacts.
122
Troubleshooting
Problem
Possible cause
Solution
Contact your network
operator.
•SIM card invalid.
Unable to
connect to the
network.
Check the service area with
your network operator.
•You are not within the
network's service area.
Move to an open space, or if
you are inside a building,
move closer to a window.
•Poor signal.
You cannot
answer
incoming
calls.
•You have activated the
Go to the menu Settings →
Call Settings → Call
Barring, and then select
Cancel All.
Call Barring feature.
•You have activated the
Go to the menu Settings →
Call Settings → Call
Barring, and then select
Cancel All.
Call Barring feature.
You cannot
make
outgoing
calls.
•You have activated the
Fixed Dial Number
feature.
Go to the menu Settings →
Call Settings → Fixed Dial
Number, and then select
Off to turn off this feature.
Contact your network
operator. If the network
operator provides the SIM
card's PUK code, use the
PUK code to unlock the SIM
card.
•You have entered an
incorrect PIN code three
consecutive times.
PIN Code is
blocked.
Contact the dealer.
•The battery or battery
charger is damaged.
Adjust the battery charging
environment to avoid
extremes of temperature.
•The phone's temperature
is below 0°C or higher
than 45°C.
Battery will
not charge.
Check all connectors to
make sure all connections
have been properly made.
•Poor contact between the
battery and charger.
Troubleshooting
123
Problem
Possible cause
Solution
Unable to
enter
Delete unnecessary data
from the Phone Book.
•The Phone Book's
memory is already full.
information
into the
Phone Book.
Contact your network
operator.
•Your network operator
does not support these
features, or you have not
applied for services that
provide these features.
Unable to
select certain
features.
124
Troubleshooting
|
Mr Coffee URT85 User Manual
Motorola Nextel i860 User Manual
Motorola IDEN I470 User Manual
Motorola I600 User Manual
Gateway DVD Player User Manual
Fujitsu MHZ2080BJ User Manual
Dell PowerVault 740N User Manual
Cypress CY14B101K User Manual
Clarion DB175MP User Manual
Casio Digital Diary SF 3990 User Manual