UAB
Compact Disc Player
Lecteur Compact Disque
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1
IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
Relocate either this product or the device that is being
affected by the interference.
2
3
IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to
the operation of other electronic devices.
■ For U.K. customers
CAUTION
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
• This label is attached to U.K. model only.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
10 cm (3 15/16 in) on the top, 10 cm (3 15/16 in) on the left
and right, and 10 cm (3 15/16 in) on the back of this unit.
Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
20 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the wall outlet. Voltages are:
................................. AC 110/120/220/230–240 V, 50/60 Hz
As long as this unit is connected to the wall outlet, it is
not disconnected from the AC power source even if
you turn off this unit by POWER.
3
4
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
5
LASER SAFETY
–
–
–
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
This unit employs a laser. Due to possible eye injury, only a qualified
service person should remove the cover or attempt to service this
device.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye
exposure to beam. When this unit is plugged into the wall outlet, do
not place your eyes close to the opening of the disc tray and other
openings to look into inside.
6
Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
Do not plug in this unit to a wall outlet until all connections
are complete.
The laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
7
8
9
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cables.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or the unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the power cable from the wall
outlet.
16 Install this unit near the wall outlet and where the power cable
can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section in this
manual on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press POWER to turn off this unit
and then disconnect the power cable from the wall outlet.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
iii En
CONTENTS
To improve audio quality (PURE DIRECT mode)
............................................................................. 10
Changing the brightness of the front panel display
............................................................................. 12
■ About this manual
•
y indicates a tip for your operation.
•
In this manual, audio CDs are referred to as “Audio CD”, MP3/WMA discs as “Data Disc”, and MP3/WMA files
stored on the USB device as “USB”.
•
This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
1 En
INTRODUCTION
FEATURES
◆ Optical Digital Output
◆ Program Play (Audio CD only)
◆ Coaxial Digital Output
◆ Random-Sequence Play
◆ CD-R, CD-RW Disc Playability
◆ MP3, WMA Disc Playability
◆ MP3, WMA File Playability Stored on USB Device
◆ Single Track/Entire Disc Repeat Play
◆ Repeat A-B Play (Audio CD only)
◆ Adjustable Display Information and Brightness
◆ PURE DIRECT Function
SUPPLIED ACCESSORIES
Please check that you received all of the following parts:
Remote control
RCA stereo cable
Power cable
Batteries (× 2)
(AA, R6, UM-3)
2 En
CONTROLS AND FUNCTIONS
Front panel
1 POWER
7
(Play)
Press to turn the power to ON/OFF.
Start playback.
y
8
(Pause)
The POWER indicator above lights up when this unit is turned
on.
Pause playback. Press
or
to resume playback.
9
(Stop)
2 USB port
Stop playback.
0 USB indicator
Lights on/off when this unit is in USB/disc mode, and
blinks when this unit is reading the USB device.
3 PURE DIRECT
Turn PURE DIRECT mode on or off to improve audio
quality.
A Front panel display
Shows the current status of this unit.
y
The PURE DIRECT indicator above lights up when this unit is in
B Remote control sensor
4 Disc tray
Receives signals from the remote control.
Load a disc.
5
(Open/Close)
Open or close the disc tray.
6
/
/
(Skip/Search backward),
(Skip/Search forward)
/
/
: Skip to the next track.
: Skip back to the beginning of the current
track.
/
(twice): Skip to the previous track.
Press and hold
/
or
/
to search
backward/ forward.
y
Each time you press and hold
/
or
/
, the
search speed increases by 2 levels.
3 En
CONTROLS AND FUNCTIONS
Front panel display
1 Lights up the icon for the selected playback mode.
3 Shows the track number selected or being played back.
4 Shows the file number.
Audio CD
also when an Audio CD is recognized on the tray.
6 Lights up when MP3 file is played back.
7 Lights up when WMA file is played back.
Data Disc
USB
4 En
CONTROLS AND FUNCTIONS
Remote control
Send infrared signals to this unit.
Switch between disc mode and USB mode.
Select brightness level for the front panel display.
Select a track directly.
Turn program mode on or off.
6
/
(Search backward/forward) (p. 11)
Search tracks backward/forward.
7
/
Skip to the next/previous track or skip back to the
beginning of the current track.
Open or close the disc tray.
Turn PURE DIRECT mode on or off.
Switch the time display.
Confirm the track number when this unit is in program
input mode.
Clear programmed track.
Repeat playback of a single track or all tracks.
Set random-sequence play.
Set repeat A-B.
F
Pause playback.
G
Start playback.
H
(Stop) (p. 10)
Stop playback.
5 En
CONTROLS AND FUNCTIONS
Installing batteries in the remote
control
Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of this unit during
operation.
Within 6 m
(20 ft)
1
2
Press the
compartment cover off.
part and slide the battery
Insert two supplied batteries (AA, R6, UM-3)
according to the polarity markings (+ and –)
on the inside of the battery compartment.
■ Handling the remote control
•
The area between the remote control and this unit must
be clear of large obstacles.
3
Slide the cover back until it snaps into place.
•
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
– high humidity, such as near a bath
– high temperature, such as near a heater or a stove
– extremely low temperatures
■ Notes on batteries
•
•
•
Change both batteries when the operation range of the
remote control decreases.
Use AA, R6, UM-3 batteries.
•
•
Make sure that the polarities are correct. See the
illustration inside the battery compartment.
Remove the batteries if the remote control is not to be
used for an extended period of time.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
•
– dusty places
•
Do not expose the remote control sensor to strong
lighting, in particular, an inverter type fluorescent
lamp; otherwise, the remote control may not work
properly. If necessary, position the unit away from
direct lighting.
•
•
•
•
If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean the
battery compartment thoroughly before installing new
batteries.
Do not throw away batteries with general house waste;
dispose of them correctly in accordance with your local
regulations.
6 En
PREPARATION
CONNECTIONS
Connecting your amplifier
CAUTION
•
•
•
Before making any connection, switch OFF the power to the unit, the amplifier and any other component.
Connections should be made to the correct input terminals of the amplifier or another component.
If the placement of this unit causes noise to another equipment, such as a tuner, move them further away from each
other.
RCA stereo
cable
Optical cable
Coaxial cable
(supplied)
Amplifier
• The digital output is turned off when this unit is in PURE DIRECT mode.
To connect this unit to your amplifier, choose one of the ways listed below.
When the ANALOG OUT terminals of this When the DIGITAL OUT (COAXIAL) terminal
unit are used ( of this unit is used (
)
)
Connect these terminals to the CD (or AUX) terminals of
the amplifier by using a supplied RCA stereo cable. For
details concerning these connections, refer to the
operation instructions of the amplifier being used.
Connect this terminal to the digital input terminal of an
amplifier with a commercially available coaxial cable.
•
Be sure that the left (L) and right (R) of these terminals
are connected to the corresponding (left and right)
terminals of the amplifier or other component.
When the DIGITAL OUT (OPTICAL) terminal
of this unit is used (
)
Connect this terminal to the optical input terminal of an
amplifier with a commercially available optical cable.
•
Use a reliable optical cable.
7 En
CONNECTIONS
Connecting the supplied power
cable
Connecting USB devices
This unit has a USB port and can access MP3 or WMA
files saved on your USB device. Connect your USB
device to the USB port on the front panel of this unit.
CAUTION
Asia and General models
only
Do not disconnect your USB device while playing back
from the USB device, or when the USB indicator blinks.
Europe and U.K. models
■ Supported USB devices
To the wall outlet with the
supplied power cable
This unit supports USB mass storage class devices (e.g.,
flash memories, card readers or portable audio players)
that use FAT16 or FAT32 format.
■ VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
the supplied power cable into the wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a straight
slot screwdriver.
Notes
• Some devices may not work properly even if they meet the
requirements.
• Do not connect devices other than USB mass storage class
devices: USB chargers, USB hubs, PCs, external HDD, etc.
• When you insert two or more memory cards at the same time
into a card reader connected to the USB port on this unit, only
one of the memory cards is recognized.
• Yamaha and suppliers accepts no liability for the loss of data
saved on the USB devices connected to this unit. As a
precaution, it is recommended that the files are made backup
copies.
Voltages are as follows:
.............................. AC 110/120/220/230-240 V, 50/60 Hz
• Playability of and power supply to all kind of USB devices are
not guaranteed.
■ Connecting this unit to the wall outlet
Plug the supplied power cable into the AC IN on the rear
panel of this unit and then plug the power cable into the
wall outlet after all other connections are complete.
8 En
OPERATION
This manual describes how to operate this unit by using the remote control.
To operate this unit from the front panel, use the corresponding buttons on the front panel.
The Audio CD , Data Disc and
used in the operation.
USB
icons indicate music data formats that can be
BASIC OPERATION
Notes
• When you load a disc, set the disc on the inside of the disc
guides (4 marks on the disc tray).
• The disc may not be read correctly, if it is set incorrectly. In this
case, open the disc tray and set the disc again.
2
Press OPEN/CLOSE to close the disc tray.
1
2
Press POWER to turn on the power.
y
You can also close the disc tray by pressing h, a numeric button,
or by pressing the front edge of the disc tray gently. If the tray is
closed in one of these ways, playback starts automatically.
3
Press h to start playback.
Press CD/USB to switch between disc mode
and USB mode.
For an Audio CD, playback starts from the first track,
and for a Data Disc, in alphanumeric order by
filename.
When USB mode is selected, the USB indicator lights
up, and when disc mode is selected, the USB
indicator lights off.
Display information in step 2
Audio CD
y
This setting is retained even if you turn off this unit.
Starting playback
Total number of tracks
Data Disc
Total recorded time of a disc
■ Playing back discs
Audio CD
Data Disc
1
Press OPEN/CLOSE to open the disc tray,
and load a disc.
Label side up.
Total number of files
Disc tray
9 En
BASIC OPERATION
■ Playing back USB devices
Turning off the power
USB
Press POWER again.
Connect your USB device to the USB port on the
When USB mode is selected (USB indicator lights up),
first filename is displayed in the front panel display (refer
date and time of creation if playable files are in the USB
device.
If you turn off the power when disc mode is selected, the
next time you turn the power on, playback starts
automatically of the disc on the tray. If you turn off the
power when USB mode is selected, playback will start
automatically of the USB device connected.
Playing back a desired track
To disconnect USB devices
Press
device.
to stop playback, and then disconnect the USB
Audio CD
Select a desired track by using the numeric
buttons.
Example: To select track number 12
Press “1”, and then press “2”.
Note
+
Do not disconnect your USB device while playing back from the
USB device, or when the USB indicator blinks.
Following information is displayed.
Pausing playback
Audio CD
Data Disc
USB
The selected track number
Playback starts in 2 seconds.
Press e.
Note
This operation is not available for Data Disc and USB.
y
You can also select and playback a desired track during playback.
To resume playback, press e again (or press h).
To improve audio quality (PURE
DIRECT mode)
Stopping playback
Audio CD
Data Disc
USB
Audio CD
Data Disc
USB
Press s.
Press PURE DIRECT.
This unit is set to PURE DIRECT mode.
• The PURE DIRECT indicator lights up.
• The digital output is turned off.
If you press h again, playback starts from the first track.
• The front panel display is turned off and only the minimum
required indicators and messages are displayed during
playback.
Note
Connect using the ANALOG OUT terminals when you use
10 En
BASIC OPERATION
y
• Press PURE DIRECT again to turn off PURE DIRECT mode.
• This setting is retained even if you turn off this unit.
Advancing or reversing playback
rapidly
Audio CD
Data Disc
USB
Skipping to the beginning of a
desired track
To advance rapidly, press
playback.
once during
Audio CD
Data Disc
USB
To play back from the beginning of the next
track, press once.
To reverse rapidly, press
playback.
once during
To play back from the beginning of the current
track, press once.
To resume playback, press
point.
at the desired
To play back from the beginning of the previous
y
track, press
twice.
• These operations can also be performed for Data Disc/USB.
• The sound can be heard (although slightly garbled) during these
operation in either direction. This is convenient for locating a
precise position within a track, or for reviewing the contents
quickly. Sound may not be heard depending on the MP3/WMA
file.
• Each time you press
by 2 levels.
• These operations can also be performed pressing and holding
b/w or f/a on the front panel for more than 2
seconds.
or
, the search speed increases
y
• These operations can also be performed for Data Disc/USB.
• These operations can also be performed when the unit is
paused.
• These operations can also be performed using b/w and
f/a on the front panel.
11 En
BASIC OPERATION
Changing front panel display
■ When playing back an Audio CD
Audio CD
You can select the following front panel displays (1 - 3) by pressing DISPLAY.
1 Elapsed time of the current track (Default)
2 Remaining time of the current track
3 Remaining time of the disc
■ When playing back a Data Disc or USB device
Data Disc
USB
You can temporarily display the filename by pressing DISPLAY.
These front panel display examples are for an MP3 file.
1 Elapsed time of the current track
Returns to the normal display after displaying
a filename.
2 Filename*
* 28 characters maximum
Note
This unit can only show alphanumeric characters.
Changing the brightness of the front panel display
Press DIMMER to change the brightness level for
the front panel display.
Notes
• Brightness is slightly decreased during playback, except when
the level is set to maximum.
• Brightness may temporarily be decreased for some operations,
except when the level is set to maximum.
Each time you press DIMMER, the brightness level
changes in the following order:
• This setting is retained even if you turn off this unit.
Max (brightest) J Level1 (default) J Level2 J Level3
(darkest) J Max
12 En
RANDOM-SEQUENCE PLAY
Audio CD
Data Disc
USB
Note
You can play back the tracks in random sequence.
These operations can also be performed for Data Disc/USB.
To perform random-sequence play
Press , and then, RANDOM.
+
To cancel random-sequence play
Press
.
REPEAT PLAY
Repeating a selected item
S (Single repeat)
Audio CD
Data Disc
USB
A single track is played back repeatedly.
You can play back a single track or all tracks repeatedly
by pressing REPEAT during playback. The repeat
playback mode changes each time you press REPEAT.
ALL (Full repeat)
All tracks (the entire disc) are played back repeatedly.
Note
These operations can also be performed for Data Disc/USB.
(Single repeat)
y
Repeat play also works for program play and random-sequence
play.
(Full repeat)
(off)
13 En
REPEAT PLAY
Repeat A-B
To cancel repeat A-B
Press A/B again to make “A-B” disappear from the front
panel display.
Audio CD
You can repeat a specified section of a track by pressing
A/B during playback to set two points (start and end
points).
Notes
• You cannot set repeat A-B from one track to another track.
• This operation is not available for Data Disc and USB.
• If you stop playback by pressing , repeat A-B is canceled.
• You cannot use repeat A-B when this unit is in PURE DIRECT
mode.
1
2
Press A/B to select the start point of repeat
play.
“A-” lights up.
Press A/B to select the end point of repeat
play.
“A-B” lights up.
The selected section is played back repeatedly.
14 En
PROGRAM PLAY
Following information is displayed.
When you press “6”:
Audio CD
You can customize the playback order of up to 50 tracks
stored on an Audio CD. This operation is not available for
Data Disc and USB.
The selected track number
When you press ENTER:
Total number of tracks
currently programmed
Total time of the tracks
currently programmed
Repeat this operation to program more tracks.
You can select the same track again.
Note
1
2
Press s to stop playback.
Pressing PROGRAM in program input mode exits to normal
playback mode, though programmed tracks are stored.
4
Press h to start program play.
Press PROGRAM.
Following information is displayed.
• In this mode, the front panel
display shows as normally, even
when this unit is in PURE
DIRECT mode.
Elapsed time of the
current track
This unit is set to program input mode.
Current track
3
Program a desired track by pressing the
corresponding numeric button and ENTER.
+
15 En
PROGRAM PLAY
Stopping program playback
Press s.
To restart program play, press h after pressing
PROGRAM.
Playback starts from the first programmed track number.
Clearing programmed track
There are several methods, as described below.
■ Clearing the last programmed track
Press CLEAR during program input mode.
Following information is displayed.
Total number of the
tracks currently
programmed
Total time of the
tracks currently
programmed
The last programmed track is cleared.
■ Clearing all programmed tracks
Press CLEAR after exiting program input
mode.
Following information is displayed.
All programmed tracks are cleared.
The display is turned off after 2 seconds.
Note
Switching to USB mode, opening the disc tray or switching off
the POWER clears all programmed tracks.
16 En
ADDITIONAL INFORMATION
NOTES ABOUT DISCS/MP3, WMA FILES
■ Discs playable with this unit
MP3
MP3 is a standard technology and format for compressing
an audio sequence into a small-sized file. However, the
original level of sound quality is preserved during
playback.
Audio CD Data Disc
This player is designed for playing back compact discs
bearing the marks shown below. Never attempt to load
any other type of disc into the unit. The unit can also play
back 8-cm (3-inch) compact discs.
The playable formats are:
•
•
•
MPEG-1 Audio Layer-3
Bitrate*: 32-320 kbps
....
Compact discs (digital audio)
Sampling frequency: 44.1/48/32 kHz
MPEG-2 Audio Layer-3, 2
Bitrate*: 8-160 kbps
Sampling frequency: 24/22.05/16 kHz
MPEG-2.5 Audio Layer-2
Bitrate*: 8-160 kbps
The most popular discs for commercially
available audio CDs.
....
CD-R,CD-RW digital audio discs
Music CDs made by copying onto a CD-R
or CD-RW (including MP3 or WMA
format files).
Sampling frequency: 12/11.025/8 kHz
* Variable bitrate is supported.
Notes
• Be sure to use a CD-R or CD-RW disc made
by a reliable manufacture.
• Be sure to use a CD-R or CD-RW disc which
has at least one of the following phrases on
the disc or disc case.
WMA
“WMA (Windows Media Audio)” is a Microsoft file
format for encoding digital audio files similar to MP3
though can compress files at a higher rate than MP3.
The playable formats are:
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Be sure to use a finalized CD-R or CD-RW
disc.
•
•
Version 8
Version 9 (Standard and variable bitrates are
supported. Professional and Lossless are not
supported.)
•
•
High Profile
Bitrate*: 32-320 kbps
Sampling frequency: 48/44.1/32 kHz
Mid Profile
Bitrate: 16-32 kbps
....
CD-TEXT discs
The discs recorded with text data such as
album titles, track titles and artist names.
Though these discs can be played back
with ordinary CD players, the text data is
not displayed.
Sampling frequency: 22.05/16 kHz
* Both constant and variable bitrates are supported.
Notes
Note
This compact disc player may not be able to play back some
CD-RW discs or discs on which recording was not made
correctly.
• Playback for Data Disc starts in alphanumeric order.
• Playback for USB starts in order by date and time of creation.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO9660 compatible.
• Text data contained in files is not displayed on this unit.
• The maximum file and folder numbers are as follows.
To prevent a malfunction of this unit:
•
Do not use any nonstandard
shaped disc (heart, etc.) available
on the market because it might
damage the unit.
Data Disc
512
USB
999
Maximum file number
255
255
Maximum folder number
•
Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
511
255
Maximum file number per
folder
■ About MP3 and WMA files
Data Disc
USB
You can play back MP3 and WMA files recorded on a
CD-R/CD-RW and those stored on a USB device.
(continued on the next page)
17 En
NOTES ABOUT DISCS/MP3, WMA FILES
To play back an 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.
■ Notes about handling compact discs
•
Always handle a disc with care so that its surface is not
scratched.
•
•
Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc
is being handled can adversely affect the disc playback.
Be sure to use a felt-tip pen or similar writing tool
when writing on the label side of the disc. Do not use a
ballpoint pen, pencil, or other hard-tipped writing tool,
as these may damage the disc and may adversely affect
the disc playback.
•
•
Do not warp discs.
When a disc is not being used, remove it from the unit
and store in an appropriate case.
•
•
When removing or storing a disc, be careful not to
scratch the playing surface.
Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even
so they should be kept clean. Wipe by using a clean,
dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
•
•
Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid because such
substances might irreparably damage the disc’s
surface.
Do not expose discs to direct sunlight, high
temperature or high humidity for a long period of time,
as these might warp or otherwise damage the disc.
No!
18 En
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the problem can be corrected by the
simple measures suggested. If it cannot be corrected, or if the problem is not listed in the Problems column, disconnect
the power cable and contact your authorized Yamaha dealer or service center for help.
Refer to
page
Problems
Possible Causes
Solutions
This unit fails to turn The power cable is not connected to the AC IN
Connect the power cable firmly.
on.
inlet on the rear panel or not plugged in the wall
outlet.
The disc tray does
not close completely.
A foreign object is obstructing the tray.
Carefully check the disc tray and remove the
foreign object.
—
—
—
Disc playback does
not start.
The disc is damaged.
Check the disc carefully; replace it if necessary.
There is moisture on the laser pickup.
Wait 20 to 30 minutes after switching on the
unit ON before trying to play back a disc.
The disc is loaded upside down.
The disc is dirty.
Reload the disc with the label side up.
Clean the disc.
The format of the MP3 or WMA file is not
compatible with this unit.
Replace the disc with a correctly recorded disc
playable with this unit.
The CD-RW (ReWritable) disc is not recorded
correctly.
Replace the disc with a correctly recorded disc
playable with this unit.
The disc is a non-standard disc not playable with Replace the disc with a correctly recorded disc
this unit.
playable with this unit.
This unit is in USB mode.
Improper USB device connections.
Switch to disc mode by pressing CD/USB.
Connect the USB device again.
5, 9
USB playback does
not start.
The format of the MP3 or WMA file is not
compatible with this unit.
Replace the file with a correctly recorded file
playable with this unit.
This unit is in disc mode.
Switch to USB mode by pressing CD/USB.
5, 9
Playback is delayed,
or begins at the
wrong place.
The disc may be scratched or damaged.
Check the disc carefully; replace it if necessary.
No sound.
Improper output cable connections.
Improper amplifier operation.
PURE DIRECT is turned on.
Connect the cables properly. If the problem
persists, the cables may be defective.
Set the amplifier controls to the correct input
selection.
—
Sound of a
component
Turn PURE DIRECT off. Or make an analog
connection.
connected to the
DIGITAL OUT jacks
is not played.
Sound “skips”.
This unit is being subjected to vibrations or
impacts.
Relocate this unit.
Clean the disc.
—
The disc is dirty.
Sound “hums”.
Improper cable connections.
Securely connect the audio cables. If the
problem persists, the cables may be defective.
Noise from a nearby
tuner.
The tuner is too close to this unit.
The disc may be warped.
Move the tuner and this unit farther apart.
—
—
Noise from inside of
the disc tray.
Replace the disc.
19 En
TROUBLESHOOTING
Refer to
page
Problems
Possible Causes
Wrong distance or angle.
Solutions
The remote control
does not work or
function properly.
The remote control functions within a
maximum range of 6 m (20 ft) and no more than
30 degrees off-axis from the front panel.
Direct sunlight or lighting (from an inverter type Reposition this unit.
of fluorescent lamp, etc.) is striking the remote
control sensor of this unit.
—
The batteries are weak.
Replace all batteries.
SPECIFICATIONS
Audio Section
General
• Frequency response......................................2 Hz - 20 kHz, ± 0.5 dB
• Harmonic distortion + noise (1 kHz) .........................0.002 % or less
• S/N ratio ....................................................................110 dB or more
• Dynamic ...................................................................100 dB or more
• Output voltage (1 kHz, 0 dB)........................................... 2.0 ± 0.3 V
• Power requirements
U.S.A. and Canada models...............................AC 120 V, 60 Hz
Australia model ................................................AC 240 V, 50 Hz
Europe and U.K. models .......................... AC 220-240 V, 50 Hz
Asia and General models.......AC 110-120/220-240 V, 50/60 Hz
Korea model .....................................................AC 220 V, 60 Hz
China model......................................................AC 220 V, 50 Hz
• Power consumption ...................................................................16 W
• Dimensions (W × H × D) ...................................435 × 96 × 300 mm
• Weight ......................................................................................6.2 kg
Laser Diode Properties
• Material ................................................................................. GaAlAs
• Wavelength ............................................................................ 790 nm
• Laser Output.............................................................. max. 1.23 μW*
Please note that all specifications are subject to change
without notice.
* This output is the value measured at a distance of about 200 mm
from the objective lens surface on the Optical Pick-up Block.
20 En
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the
proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in
force in the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the
product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.
■ For U.K. customers
Information for Users on Collection and Disposal of Old Equipment
and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
© 2008 Yamaha Corporation All rights reserved.
Printed in Malaysia
WQ01730
|