Quick Installation Guide
TV-IP602WN
1.01
1. Before You Start
Package Contents
ŸTV-IP602WN
ŸCD-ROM (Utility and User’s Guide)
ŸMulti-Language Quick Installation Guide
Ÿ2 x 2dbi Detachable Antennas
ŸNetwork Cable (1.5m/5ft.)
ŸMounting Kit
ŸPower Adapter (12V DC, 1.5A)
System Requirements
ŸA computer with a wired network adapter properly installed.
ŸCD-ROM Drive
ŸVGA Resolution: 800 x 600 or above
ŸWeb Browser: Internet Explorer (6.0 or higher)
ŸWireless Router (e.g. TEW-691GR)
ŸAn available DHCP Server –routers usually have a built-in DHCP server
CPU
Memory
Supported Operating Systems
Windows 7 (32/64-bit)
Windows Vista (32/64-bit)
Windows XP (32/64-bit)
1.3GHz or above 1GB RAM or above
1.3GHz or above 512MB RAM or above
1.3GHz or above 256MB RAM or above
1
2. Hardware Installation and Configuration
Note: It is recommended that you configure the IP Camera from a wired computer.
1. Insert the Utility CD-ROM into your CD-ROM
drive.
2. Click Run autorun.exe (Windows 7/Vista only).
3. Click Setup Wizard.
4. Click Next. Then follow the Setup Wizard
instructions.
5. Click Close.
2
6. Double click on the SetupWizard icon on your
desktop.
7. Connect the provided network cable from one
of your Router's network ports to the Ethernet
port on the IP Camera.
8. Connect the Power Adapter to the IP Camera
and then to a power outlet.
9. Click Next.
10. Select the IP camera and click Next. Verify
that the MAC address listed matches the MAC
address on your IP camera. The MAC address
is listed on the bottom of the TV-IP602WN .
Click Re-Scan if no cameras are detected.
11. Enter your ID and password. Then click Next.
By default:
ID: admin
Password: admin
12. Configure the Camera Name and Camera
Time. Click Copy Local Time to automatically
configure the Camera Time to match your
computer. Then click Next.
3
13. If you would like to change the administrator
password, click Change Password, enter a
new password, retype the new password and
then click Next. Leave Change Password
unchecked if you do not wish to change the
password.
Note:
1. Setting a password prevents other users from accessing the TV-IP602WN's
configuration.
2. It is recommended that you enter a new password. If you decide to change this
setting, please write down the new password.
3. Password is limited to up to 8 characters.
14. Select DHCP and then click Next.
15. Click I want to use wireless for the camera
and then click Next .
16. Select your wireless network from the
Available AP dropdown list. If your wireless
network does not appear, manually enter the
SSID of your wireless network. If you have
Encryption enabled, select the
Authentication, select the Encryption and
enter your Key. Then click Next.
4
17. Click Next.
18. Please wait while the settings on your cameras
are being saved.
19. Select By using wireless and then click Next.
20. Disconnect the RJ-45 cable. Verify that the
LINK (RED) LED is lit and then click Next.
Note: The TV-IP602WN will not work wirelessly until you disconnect the Ethernet cable
from the back of the camera.
21. Please wait while the settings on your
cameras are being saved.
5
22. Click on the following URL or click Link to
open up the browser configuration.
23. Enter the User name and Password, and then
click OK. By default:
User Name: admin
Password: admin
24. Right click on the information bar and select
Install This Add-on for All Users on This
Computer… (Internet Explorer 8)
25. Click Install. (Internet Explorer 8)
26. Right click on the information bar and select
Install ActiveX Control
(Internet Explorer 6/7).
27. Click Install (Internet Explorer 6/7).
6
28. Live Video will now appear.
29. Use the command icons to control the IP
camera
30. Unplug the power adapter and disconnect the
TV-IP602WN from your computer. Place the
TV-IP602WN in your desired location. Please
refer to the Wireless Tips section for optimal
placement of the TV-IP602WN .
31. Plug the power adapter back into the
TV-IP602WN .
Your installation is complete
1. For detailed information regarding the TV-IP602WN configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
2. If you would like to use IPViewPro 2.0 software, please install the software by clicking
Install IPView Pro 2.0 in the Autorun window and refer to the User's Guide on the CD for
more information.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
Thank you for choosing TRENDnet
7
Troubleshooting
1. I inserted the Utility CD-ROM into my computer's CD-ROM Drive but the installation menu
does not appear automatically. What should I do?
1. For Windows 7, if the installation menu does not appear automatically, click on the
Windows Icon on the bottom left hand corner of the screen,, click the “Search programs
and files” box, and type D:\autorun.exe, where “D” in “D:\autorun.exe” is the letter
assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard .
2. For Windows Vista, if the installation menu does not appear automatically, click Start, click
the Start Search box, and type D:\autorun.exe where "D" in "D:\autorun.exe" is the letter
assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard.
3. For Windows XP, if the window does not appear automatically, click Start, click Run
and type D:\autorun.exe where “D” in “D:\autorun.exe” is the letter assigned to your
CD-ROM Drive, and then press the ENTER key on your keyboard.
2. Setup Wizard is unable to detect my camera. What should I do?
1. Verify that you have followed all the steps in Section 2: Hardware Installation.
2. Disable any software firewall programs such as ZoneAlarm or Norton Internet Security. If
you are using Windows 7, Vista or XP disable the built in firewall.
3. Click on Re-scan in the Setup Wizard.
4. Take a pin or paper clip. Then press on the Reset button on the back on the IP Camera
for 10 seconds, then let go.
3. I do not have a DHCP server or DHCP is disabled on my network and I am unable to
configure the TV-IP602WN. What should I do?
1. Go to the TCP/IP settings on your computer and assign a static IP address on your
computer's network adapter in the subnet of 192.168.10.x. Since the default IP address of
the TV-IP602WN is 192.168.10.30, do not assign a static IP address of 192.168.10.30 on
your computer's network adapter.
4. The Image is blurry. How can I adjust the focus on the Internet camera?
You can adjust the Internet Camera's focus by rotating the lens.
5. When I click on Live View the image does not load?
1. Make sure that you are using a browser that supports Active X.
2. Make sure that ActiveX is installed. See steps 25 to 28 in Section 2: Hardware
Installation and Configuration.
6. How do I connect the TV-IP602WN to my wireless router or access point?
Make sure that you configure the camera to have the same SSID, encryption mode and key
(if enabled). Follow the instructions in section 2 to configure the camera with the SSID and
encryption key.
8
7. After I successfully configured the TV-IP602W to match my wireless network settings, I
can not connect to the camera.
1. Verify that the wireless settings match your wireless network settings.
2. Verify in the wireless section of the browser configuration that the Enable Wireless option
is checked.
3. Make sure to disconnect the Ethernet cable from the camera and verify that the
LINK LED is blinking red.
4. Please refer to the Wireless tips section if you continue to have wireless connectivity
problems.
8. I forgot my password. What should I do?
Take a pin or paperclip and press the reset button on the back of the unit for 15 seconds.
This will return settings back to factory defaults. Open up the SetupWizard program to find
out the IP address of the camera (see step 11 in Section 2: Hardware Installation and
Configuration. If you do not have a DHCP server on your network, the default IP address is
192.168.10.30. The default administrator ID and password is admin.
If you still encounter problems or have any questions regarding the TV-IP602WN, please contact
TRENDnet's Technical Support Department.
9
Wireless Tips
The following are some general wireless tips to help minimize the impact of interference within an
environment.
Assign your network a unique SSID
Do not use anything that would be identifying like “Smith Family Network”. Choose
something that you would easily identify when searching for available wireless networks.
Do not turn off the SSID broadcast
The SSID broadcast is intended to be on and turning it off can cause connectivity issues.
The preferred method of securing a wireless network is to choose a strong form of encryption
with a strong and varied encryption key.
Note: after setting up the SSID, encryption type and encryption key/passphrase, please
make a note of them for future reference. You will need this information to connect your
wireless computers to the wireless router/access point.
Change the channel
Most wireless access points and routers are defaulted to channel 6. If you have a site survey
tool that will display the channels you can plan your channel selection around neighboring
access points to minimize interference from them. If your site survey tool does not display
the channel try using channels 1 or 11.
If using 802.11n you should be securing the network with WPA2 security.
Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP
encryption this device may operate in legacy wireless mode (802.11b/g). You may not get
802.11n performance as these forms of encryption are not supported by the 802.11n
specification.
Please also make sure that the wireless hardware is not placed in any type of shelving or
enclosures.
Avoid stacking hardware on top of each other to prevent overheating issues. Maintain
enough free space around the hardware for good ventilation and airflow. There should also
be plenty of free space around the antennas to allow the wireless signal to propagate.
10
There are a number of other environmental factors that can impact the range of wireless devices.
1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at
an angle. The more material the signal has to pass through the more signal you will lose.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of
a wireless device. Position the wireless devices in a manner that will minimize the amount
of obstructions between them.
3.Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through less
dense material such as dry wall. Dense materials like metal, solid wood, glass or even
furniture may block or degrade the signal.
4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless
adapter's site survey tool to determine the best antenna orientation for your wireless
devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your
signal. Position your wireless devices away from anything that generates RF noise, such
as microwaves, HAM radios, Walkie-Talkies and baby monitors.
6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as
2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency
can potentially drop the wireless signal. Although the phone may not be in use, the base
can still transmit wireless signal. Move the phone's base station as far away as possible
from your wireless devices.
If you are still experiencing low or no signal consider repositioning the wireless devices or
installing additional access points. The use of higher gain antennas may also provide the
necessary coverage depending on the environment.
11
Copyright ©2011. All Rights Reserved. TRENDnet.
|