Driver for the XCG Series
High Resistance to Shock and Vibration
Due to their robustness and vibration resistance, the
XCG Series cameras deliver outstanding performance in the
most challenging environmental conditions.
The XCG Series is equipped with a Sony-provided, dedicated
driver. This image filter driver enables jumbo-packet data
transfer across all industry-standard hardware. It is also
capable of non-GigE Vision data transfer in GigE Vision
environments.
Other features
• Vertical and Horizontal Partial Scanning
• Vertical Binning
Bulk Trigger Mode/Sequential Trigger Mode
In addition to its conventional trigger mode, the XCG Series
features an advanced“Bulk Trigger Mode”and“Sequential
Trigger Mode.” “Bulk Trigger Mode”allows the XCG Series to
capture up to 16 images in rapid succession using a single
software or hardware trigger. “Sequential Trigger Mode”
periodically sends a software or hardware trigger to the
camera to capture the successive images. With the cameras’
memory channel, up to 16 different settings can be called up
to capture these images. Thanks to these beneficial trigger
options, the XCG Series reduces the need to receive signals
from the host PC.
DIMENSIONS
PIN ASSIGNMENT
12-pin connector
Pin No.
1
2
DC IN (Ground)
DC IN
3
GND
4
Strobe/Exposure OUT
ISO OUT- (Isolated)
ISO OUT+ (Isolated)
ISO IN+ (Isolated)
GND
2-3 depth 4
19
/32 (13)
5
6
3 (75.5)
7
RJ-45
3
(screw connectors)
17
3
1
/4 (44)
/32 (8)
2
/4 (67.5)
8
9
NC
10
11
12
NC
Trigger IN
ISO IN- (Isolated)
Power LED (Green)
2-M2
12-pin connector
17
3
/32 (13)
2
/8 (60)
1
1
/2 (37.5)
4-3 depth 4
Unit:inches (mm)
OPTIONAL ACCESSORIES
Tripod Adaptor
Camera Adaptor
Cables
VCT-ST701
DC-700
CCXC-12P02N
CCXC-12P05N
CCXC-12P10N
CCXC-12P25N
3
Specifications
XCG-5005E
XCG-U100E
XCG-SX99E
XCG-SX97E
XCG-V60E
2/3-type progressive scan
IT CCD
1/1.8-type progressive scan 2/3-type progressive scan
2/3-type progressive scan
IT CCD
1/3-type progressive scan
IT CCD
Image device
IT CCD
IT CCD
Cell size (H x V)
Standard picture size (H x V)
Resolution depth
Lens mount
3.45 x 3.45 μm
4.4 x 4.4 μm
1,600 x 1,200 pixels
6.45 x 6.45 μm
1,360 x 1,024 pixels
8/10/12 bits/pixel
C mount
6.45 x 6.45 μm
7.4 x 7.4 μm
2,448 x 2,048 pixels
1,360 x 1,024 pixels
640 x 480 pixels
Standard frame rate
Digital interface
Sensitivity
15 fps
15 fps
27 fps
16 fps
90 fps
1000BASE-T (GigE Vision compatible)
400 lx at F5.6 (0 dB)
400 lx at F5.6 (0 dB)
400 lx at F8 (0 dB)
400 lx at F11 (0 dB)
400 lx at F5.6 (0 dB)
Less than 1 lx
(Gain +18 dB, F1.4)
Less than 1 lx
(Gain +18 dB, F1.4)
Less than 0.4 lx
(Gain +18 dB, F1.4)
Less than 0.2 lx
(Gain +18 dB, F1.4)
Less than 1 lx
(Gain +18 dB, F1.4)
Minimum illumination
Gain control
Manual 0 to +18dB,Auto gain
Normal/Binning/Partial scan
Vertical (1x2)
Readout mode
Binning
Partial scan
Vertical/Horizontal
Shutter speed
2 to 1/100,000 s
External trigger shutter
Memory channel
Readout features
Power requirements
Power consumption (Max.)
Dimensions
Pulse-edge detection mode, Pulse-width detection mode, Special trigger mode (Bulk trigger mode/Sequential trigger mode)
16 channels
Binnarization, Gamma correction (LUT), Built-in test pattern
DC+10.5 to +15.0 V
4.3 W
3.1 W
3.6 W
3.1 W
3.1 W
1 3/4 x 1 5/16 x 2 3/4 inches (44 x 33 x 67.5 mm)
Less than 5 3/4 oz (145 g)
23 to 113 °F (-5 to 45 °C)
-22 to 140 °F (-30 to 60 °C)
20 to 80% (no condensation)
20 to 95% (no condensation)
10 G (20 to 200Hz)
Weight
Operating temperature
Storage temperature
Operating humidity
Storage humidity
Vibration resistance
Shock resistance
Supplied accessories
70 G
Lens mount cap, Operating instructions
© 2010 Sony Electronics Inc. All rights reserved.
Reproduction in whole or in part without written permission is prohibited.
Design, features, and specifications are subject to change without notice.
All non-metric weights and measurements are approximate.
Sony is a registered trademark of Sony Corporation.
Sony Electronics Inc.
1 Sony Drive
All other trademarks are the properties of their respective owners.
Park Ridge, NJ 07656
IS-1216B (MK10570V1)
Printed in USA (3/10)
|