PROFESSIONAL DISC RECORDER
PDW-F1600
PDW-HD1500
The supplied CD-ROM includes operation manuals for the PDW-F1600/HD1500 Professional Disc
Recorder (English, Japanese, French, German, Italian, Spanish and Chinese versions) in PDF
format.
OPERATION MANUAL [English]
1st Edition (Revised 3)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
WARNING
Excessive sound pressure from earphones and headphones
can cause hearing loss.
In order to use this product safely, avoid prolonged listening at
excessive sound pressure levels.
This Professional Disc Recorder is classified as a CLASS 1
LASER PRODUCT.
Laser diode properties
VAROITUS!
Wave length: 400 to 410 nm
Emission duration: Continuous
Laser output power: 135 mW (max. of pulse peak), 65 mW
(max. of CW)
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
Standard: IEC60825-1 (2001)
VARNING
Egenskaber for laserdiode
Bølgelængde: 400 til 410 nm
Strålingsvarighed: Kontinuerlig
Afgivet lasereffekt: 135 mW (maks stråletoppunkt), 65 mW
(maks ved kontinuerlig stråling)
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
When installing, the installation space must be secured in
consideration of the ventilation and service operation.
• Do not block the ventilation slots at the left side, right side
and bottom of front side panels, and vents of the fans.
• Leave more than 25 cm of space in the rear of the unit.
• Leave more than 2 cm of space in the left side, right side and
top of the unit.
Standard: IEC60825-1 (2001)
Tekniska data för laserdiod
Våglängd: 400 till 410 nm
Emissionslängd: Kontinuerlig
Laseruteffekt: 135 mW (max. för pulstopp), 65 mW (max. för
kontinuerlig våg)
Standard: IEC60825-1 (2001)
For the customers in the USA
Egenskaper for laserdiode
Bølgelengde: 400 til 410 nm
Strålingsvarighet: Uavbrutt
Utgangseffekt for laser: 135 mW (maks av pulshøyde), 65
mW (maks av CW)
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Standard: IEC60825-1 (2001)
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
This label is located on the top panel of the drive unit.
Denna etikett finns på ovansidan av driftenheten.
Denne mærkat sidder på drevenhedens øverste panel.
Tämä kyltti sijaitsee ajurilaitteen yläpinnalla.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Dette merket er plassert på oversiden av driverenheten.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-
003.
CAUTION
The use of optical instruments with this product will increase
eye hazard.
For the customers in Europe
This product with the CE marking complies with both the EMC
Directive and the Low Voltage Directive issued by the
Commission of the European Community.
3
Compliance with these directives implies conformity to the
following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment, ex. TV
studio).
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
Cette étiquette est placée sur le panneau supérieur de l’unité
de commande.
The Authorized Representative for EMC and product safety is
Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or guarantee matters
please refer to the addresses given in separate service or
guarantee documents.
AVERTISSEMENT
Une pression acoustique excessive en provenance des
écouteurs ou du casque peut provoquer une baisse de l’acuité
auditive.
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
Pour utiliser ce produit en toute sécurité, évitez l’écoute
prolongée à des pressions sonores excessives.
Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan
Pour les clients au Canada
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
For the Customers in Taiwan only
Pour les clients européens
Ce produit portant la marque CE est conforme à la fois à la
Directive sur la compatibilité électromagnétique (EMC) et à la
Directive sur les basses tensions émises par la Commission
de la Communauté Européenne.
La conformité à ces directives implique la conformité aux
normes européennes suivantes :
• EN60065 : Sécurité des produits
• EN55103-1 : Interférences électromagnétiques (émission)
• EN55103-2 : Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans les environnements
électromagnétiques suivants :
E1 (résidentiel), E2 (commercial et industrie légère),
E3 (urbain extérieur) et E4 (environnement EMC contrôlé ex.
studio de télévision).
AVERTISSEMENT
Afin de réduire les risques d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution,
garder le coffret fermé. Ne confier
l’entretien de l’appareil qu’à un personnel
qualifié.
AVERTISSEMENT
1.Utilisez un cordon d’alimentation (câble secteur à 3 fils)/
fiche femelle/fiche mâle avec des contacts de mise à la terre
conformes à la réglementation de sécurité locale applicable.
2.Utilisez un cordon d’alimentation (câble secteur à 3 fils)/
fiche femelle/fiche mâle avec des caractéristiques
nominales (tension, ampérage) appropriées.
Pour toute question sur l’utilisation du cordon d’alimentation/
fiche femelle/fiche mâle ci-dessus, consultez un technicien du
service après-vente qualifié.
CET APPAREIL DOIT ÊTRE RELIÉ À LA
TERRE.
ATTENTION
Pour les clients en Europe
Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan,
Eviter d’exposer l’appareil à un égouttement ou à des
éclaboussures. Ne placer aucun objet rempli de liquide,
comme un vase, sur l’appareil.
Minato-ku, Tokyo, Japon.
Le représentant autorisé pour EMC et la sécurité des produits
est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Allemagne. Pour toute question concernant le
service ou la garantie, veuillez consulter les adresses
indiquées dans les documents de service ou de garantie
séparés.
Cet appareil n’est pas déconnecté de la source d’alimentation
secteur tant qu’il est raccordé à la prise murale, même si
l’appareil lui-même a été mis hors tension.
4
Für Kunden in Europa
WARNUNG
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die
EMV-Richtlinie sowie die Niederspannungsrichtlinie der EG-
Kommission.
Um die Gefahr von Bränden oder
elektrischen Schlägen zu verringern, darf
dieses Gerät nicht Regen oder Feuchtigkeit
ausgesetzt werden.
Um einen elektrischen Schlag zu
vermeiden, darf das Gehäuse nicht
geöffnet werden. Überlassen Sie
Wartungsarbeiten stets nur qualifiziertem
Fachpersonal.
Angewandte Normen:
• EN60065: Sicherheitsbestimmungen
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit)
Für die folgenden elektromagnetischen Umgebungen:
E1 (Wohnbereich), E2 (kommerzieller und in beschränktem
Maße industrieller Bereich), E3 (Stadtbereich im Freien) und
E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio)
WARNUNG
1. Verwenden Sie ein geprüftes Netzkabel (3-adriges
Stromkabel)/einen geprüften Geräteanschluss/einen
geprüften Stecker mit Schutzkontakten entsprechend den
Sicherheitsvorschriften, die im betreffenden Land gelten.
2. Verwenden Sie ein Netzkabel (3-adriges Stromkabel)/einen
Geräteanschluss/einen Stecker mit den geeigneten
Anschlusswerten (Volt, Ampere).
DIESES GERÄT MUSS GEERDET
WERDEN.
ACHTUNG
Das Gerät ist nicht tropf- und spritzwassergeschützt. Es
dürfen keine mit Flüssigkeiten gefüllten Gegenstände, z. B.
Vasen, darauf abgestellt werden.
Wenn Sie Fragen zur Verwendung von Netzkabel/
Geräteanschluss/Stecker haben, wenden Sie sich bitte an
qualifiziertes Kundendienstpersonal.
Solange das Netzkabel an eine Netzsteckdose
angeschlossen ist, bleibt das Gerät auch im ausgeschalteten
Zustand mit dem Stromnetz verbunden.
Für Kunden in Europa
Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
Der autorisierte Repräsentant für EMV und Produktsicherheit
ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in
Bezug auf Kundendienst oder Garantie wenden Sie sich bitte
an die in den separaten Kundendienst- oder
Garantiedokumenten aufgeführten Anschriften.
Dieser Professional Disc Recorder ist als CLASS 1 LASER
PRODUCT eingestuft.
Daten der Laserdiode
Wellenlänge: 400 bis 410 nm
Emissionsdauer. Ununterbrochen
Laser-Ausgangsleistung: 135 mW (max. Impulsspitze),
65 mW (max. Dauerstrich)
Standard: IEC60825-1 (2001)
Dieser Aufkleber befindet sich oben auf der Antriebseinheit.
WARNUNG
Zu hoher Schalldruck von Ohrhörern und Kopfhörern kann
Gehörschäden verursachen.
Um dieses Produkt sicher zu verwenden, vermeiden Sie
längeres Hören bei sehr hohen Schalldruckpegeln.
5
Table of Contents
Features..........................................................................................11
Preparations......................................................................................... 16
Display window................................................................................... 23
Supplying power.................................................................................. 32
Initial Setup ....................................................................................33
Using the editing functions of the recorder (controlling through
6
Table of Contents
Notes on handling................................................................................ 52
Continuing recording while exchanging discs (disc exchange cache
Handling of discs when recording does not end normally (salvage
Playback......................................................................................... 62
Playback operation............................................................................... 63
Overview......................................................................................... 66
Displaying menus ................................................................................ 70
7
Table of Contents
Setting clip flags.................................................................................. 82
Directory structure............................................................................. 104
Recording Continuous Timecode with FAM and FTP
8
Table of Contents
Digital hours meter ............................................................................ 155
Correspondence between Setting Items of the HKDV-900 and
9
Table of Contents
Overview
1
Chapter
Marks for Model-Specific Features
Functions
The PDW-F1600 or PDW-HD1500 is a professional disc
recorder supporting full HD (1920 × 1080 and 1280 × 720)
playback and recording with Professional Disc media.
1)
In this manual, functions that are supported only by the
PDW-F1600 or only by the PDW-HD1500 are indicated
by the following marks.
When you use this unit in combination with a nonlinear
editing system, the FAM function enables data file
transfers between the unit and computers over the
i.LINK interface, allowing the unit to be used like an
2)
: PDW-F1600
F1600
3)
: PDW-HD1500
HD1500
external hard drive. The unit can be used as a player for
video editing and program output, and as a recorder for
nonlinear editing.
For these applications, it can be connected to Sony
nonlinear editors, monitors, and video equipment with
HDSDI interfaces via its standard HDSDI I/O connectors.
It has a compact, lightweight body for easy portability
outdoors, and can be powered from any of three power
4)
sources: AC, DC, or battery power.
1) Professional Disc is a trademark of Sony Corporation.
2) FAM: File access mode
3) This unit does not support DV stream output.
4) BKP-L551 Battery Adaptor is required.
Features of this unit
The principal features of this unit are as follows.
1)
MPEG HD422 codec
High-quality video and audio recording and
playback
The MPEG HD422 codec provides video compression
compliant with the MPEG-2 422P@HL standard. It
enables HD 4:2:2 (50 Mbps) digital component file
recording in the 1080i (1,080 effective scanning lines,
interlaced) or 720P (720 effective scanning lines,
progressive) format currently in use by many broadcast
facilities.
11
Marks for Model-Specific Functions / Features
Uncompressed PCM recording of 24-bit 48 kHz audio
enables 8-channel audio recording at high sound quality.
Note
Continuous playback may not be possible at the transition
point between two clips with different recording formats.
1) MPEG HD422 is a trademark of Sony Corporation.
Long recording times
F1600 Linear editing
Using this unit as the recorder, you can perform insert and
assemble editing of recorded clips.
PDW-F1600 or PDW-HD1500 supports dual-layer
Professional Discs (50 GB). When dual-layer Professional
Discs are used, this unit can record about 95 minutes.
SD upconvert function
The unit can output HD signals while playing discs
recorded as SD, allowing SD material to be utilized in an
HD environment.
Recording and playback functions
1)
1)
Support for multiple SD and HD codecs
In addition to the MPEG HD422 codec, this unit supports
HD1500
1)
When the PDBK-S1500 or PDBK-F1500 option is installed.
2)
the MPEG HD codec. It can record HD 4:2:0 digital
3)
component files at both 1080i (35/25/18 Mbps ) and 720P
HD downconvert function
(35/25 Mbps), allowing HD operation across a wide range
of recording times and application objectives. The unit is
also capable of SD (IMX 30/40/50 Mbps or DVCAM
codec) recording and playback.
The unit is provided with a downconvert function. HD disc
playback signals can be downconverted to SD signals and
then output as SDSDI or composite signals. This allows
you to use SD nonlinear editors and monitors for editing
and program output.
HD1500
1)
When the PDBK-S1500 or PDBK-F1500 option is installed.
2) MPEG HD is a registered trademark of Sony Corporation.
3) Playback only supported for 18 Mbps.
1080/720 cross-conversion
This unit supports cross-conversion output. It can output
720 while playing discs recorded as 1080, and output 1080
while playing discs recorded as 720.
Support for multiple frame frequencies
This unit can record and play multiple frame frequencies at
both 1080 (59.94i, 50i, 29.97P, 25P, and 23.98P) and 720
(59.94P and 50P) (for MPEG HD422). It can also perform
HDSDI remote recording
HDSDI connections can be made to camcorders with
remote HDSDI support (PDW-700 XDCAM HD422
1)
pulldown playback of discs recorded at 23.98P.
1)
1) HD1500 When the PDBK-S1500 option is installed.
camcorder, HDW-730/730S/750/790/F900R HDCAM
camcorders) to enable recording synchronized to REC and
STOP operations on the camcorder.
Support for mixed format recording mode
As long as the frame frequency group is the same, clips in
different recording formats can be recorded or written to
1) HDCAM is a trademark of Sony Corporation.
1)
the same disc.
Clip Continuous Rec function
The system frequencies supported by this unit are divided
into frame frequency groups, as shown in the following
table.
Normally, a clip is generated as an independent file every
time recording starts and stops. The Clip Continuous Rec
function allows you to continue recording to the same clip
until the function is stopped or turned off, regardless of
how many times recording starts and stops. This is
convenient if you want to avoid generating a large number
of short clips, or if you want to record without worrying
about the limit on the number of clips (maximum 300).
1) The recording format is regarded as different whenever the system
frequency, video resolution, video codec/bit rate, or number of audio
channels or number of bits does not match.
Frame frequency group
System frequency
59.94Hz
59.94P
59.94i
29.97P
50P
Note
This function is available only when you are operating
equipment connected to the REMOTE(9P) or SD/HDSDI
INPUT connector. It is not available on the front panel.
50Hz
50i
25P
Recording of proxy AV data
23.98Hz
23.98P
Proxy AV data is a low-resolution (1.5 Mbps video, 64
kbps per audio channel), MPEG-4 based version of a full
resolution data stream. Whenever this unit records full
resolution MPEG HD422 data, it simultaneously generates
and records low-resolution proxy AV data. Because of its
small size, proxy AV data can be transferred quickly over
computer networks, easily edited in the field with laptop
You can record clips with different recording formats, for
example HD422 and HD420SP clips, by putting this unit
into mixed format recording mode.
12
Features
1)
computers, and readily used in a wide variety of
Usability features
applications, such as content management on small-scale
servers.
1)
AC, DC, and battery power support
The unit can be used even where AC power is not
available, for example outdoors or in cars or helicopters.
1) The supplied PDZ-1 Proxy Browsing Software can be used to create
simple EDLs (Edit Decision Lists).
1) BKP-L551 Battery Adaptor is required.
High-speed searches with the jog and shuttle
dials
Color LCD display
The jog and shuttle dials can be used to find scenes inside
clips, in the same way as the jog and shuttle dials on
conventional VTRs.
The unit is equipped with a 16:9, 4.3-inch color LCD
which allows you to check the contents of the disc and use
the menu system without connecting an external monitor.
In jog and variable modes, you can search in field units at
from –2 to +2 times normal speed. Shuttle mode supports
high-speed searches up to a maximum of 20 times normal
speed. (F.FWD and F.REV are possible up to 35 times
normal speed.)
Built-in speakers
The unit features built-in speakers, allowing you to check
recorded audio. You can check your clips and editing
results on the color LCD and speakers even when no
monitors or separate speakers are available.
Convenient disc-based playback and searching
Like previous products in the XDCAM series, this unit
supports a number of convenient search functions,
including scene selection, thumbnail searches, essence
marks searches, and expand searches.
Tiltable front panel
The front panel is tiltable for easy rack-mount and desktop
operation. You can adjust the panel to the angle that makes
the buttons easiest to use.
Scene selection: This function allows you to select clips
from the disc and insert them into playlists. Clips can
be inserted and played back in any order.
Cache recording for seamless disc exchanges
About 30 seconds (this duration may differ depending on
the state of a disc) of video and audio data can be recorded
to the unit’s internal memory cache during a disc
exchange, and then written back to the newly loaded disc.
This allows seamless recording across extended recording
sessions, including recording of video feeds, with no
important scenes lost while discs are being exchanged.
Thumbnail searches: The unit creates thumbnails from
the first frame of each generated clip, and displays
them in thumbnail lists on the color LCD or an
external monitor. You can cue up clips very easily by
simply by selecting them from thumbnail lists.
Essence mark searches: Essence marks can be recorded
at any scene during or after recording. Lists of these
marks can be displayed on the color LCD or an
external monitor, allowing you to quickly find scenes
that were marked for later reference.
Cart system support
With its compact body, this unit can replace the SD PDW-
1500 unit. You can mount this unit in the PDJ-C1080 and
PDJ-A640 XDCAM cart systems.
Expand searches: This function allows you to look inside
the clip selected in a thumbnail screen, or inside the
segment from a selected essence mark to the next
essence mark. The selection range is divided into 12
equal blocks, and the first frames of those blocks are
displayed as thumbnails. By checking the thumbnails,
you can easily find the scene you want.
IT friendly
Computer access to files (file access mode)
Video and audio clip data are recorded as files. The FAM
function enables quick random access by computers to the
video, audio, and metadata files stored on Professional
Discs, with the ability to display thumbnail lists on the
computer screen and perform file-based reads and writes.
Filter Clips function
You can select clips of a certain type from among all of the
clips on a disc. For example, you can do the following.
• Select clips in a certain video format from a disc that
contains clips in different video formats.
• Select only clips with NG (bad) clip flags, and delete all
of those clips in one operation.
• Select only clips that were recorded according to
planning metadata, and use the Direct FTP function to
transfer those clips to an external device.
Equipped with network connector
The unit features a Gigabit Ethernet connector as standard
equipment. Via this connector, you can connect the unit to
computers and networks to enable listing of the video,
audio, and metadata files recorded on the Professional
Disc, and rapid file transfers. Support for FTP commands
makes it easy to carry out network file transfers from
remote locations.
The unit has two optical pickups for high-speed transfers.
Direct FTP function
You can use this unit as a local FTP host to send and
receive MXF files to and from other XDCAM devices,
13
Features
without using a computer. This function is available
through simple operations on the GUI screen.
Supports SNMP for maintenance and service
This unit supports Sony’s SNMP-based remote
maintenance and monitoring software. This software
allows you to monitor the status of the hardware via a TCP/
IP network in real time, and to record the results in a status
log.
User data recording mode
User data (files other than XDCAM AV files) can be
recorded on Professional Discs as PC data via the i.LINK
or FTP interface. This allows Professional Discs to be used
as data recording media, with a data storage capacity of
46.4 GB (when dual-layer PFD50DLA discs are used).
Supports a variety of interfaces
This unit supports the following interfaces.
• HDSDI video, 8-channel audio input and output
• SDSDI video, 8-channel audio input and output
(the SD/HDSDI INPUT connector doubles as an SDSDI
input connector)
• SD composite output
• AES/EBU digital audio 4-channel input and output
• Analog audio 2-channel input and output
• Remote
- RS-422A (D-sub 9-pin × 1)
- Video remote (D-sub 9-pin × 1)
TBC control is available from the front panel.
• i.LINK TS (HDV) input and output (when PDBK-201
option board is installed)
14
Features
System Configurations
DIGITAL
AUDIO (AES/EBU)
OUT/IN
Professional Discs
PDW-700
ANALOG
AUDIO
OUTPUT/INPUT
• PFD23A
• PFD50DLA
HKDV-900
a)
HKDV-900 video control unit
PDW-1500
Sony BP-L80S/GL95
battery
SDSDI
OUTPUT
HDSDI
INPUT
VIDEO
CONTROL
BKP-L551 battery
adaptor
EJECT
RM-280 editing
controller
REMOTE
MARK1
OUT
PUSH SET(S.SEL)
ACCESS
IN
REMOTE (9P)
CH-1
CH-3
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
CH-4
DC IN 12V
RESET
REMOTE (9P)
DC power source
AC power source
CHAPTER
RETURN
EXPAND
- AC IN
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
BVE-700
ANALOG AUDIO INPUT
PHONES
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
SDSDI
OUTPUT
COMPOSITE
OUTPUT
DIGITAL
AUDIO
(AES/EBU)
OUT/IN
ANALOG
AUDIO
OUTPUT/
INPUT
HDSDI
OUTPUT/
INPUT
Microphone
SD video monitor
Headphones
HDSDI
OUTPUT
HDCAM
HD video monitor
Audio monitor
REMOTE
(9P) b)
AUDIO
MONITOR
HDW-2000 series
(i.LINK) S400
PDW-F75
Laptop computer
a) If an HKDV-900 is connected, be sure to check that the
version of the HKDV-900 is 2.00 or higher.
b) For HDW-2000 series only.
15
System Configurations
Using the CD-ROM
Manual
The supplied CD-ROM includes versions of the Operation
Manual for the PDW-HD1500 in English, Japanese,
French, German, Italian, Spanish and Chinese in PDF
format.
Preparations
The following program must be installed on your computer
in order to read the operation manuals contained on the
CD-ROM.
• Adobe Reader Version 6.0 or higher
Memo
If Adobe Reader is not installed, you can download it from
the following URL:
http://www.adobe.com/
Adobe and Adobe Reader are trademarks of Adobe
Systems Incorporated in the United States and/or other
countries.
Reading the CD-ROM manual
To read the operation manual contained on the CD-ROM,
do the following.
1
2
Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your browser.
If it does not appear automatically in the browser,
double-click on the index.htm file on the CD-ROM.
Select and click on the operation manual that you want
to read.
This opens the PDF file of the operation manual.
Memo
The files may not be displayed properly, depending on the
version of Adobe Reader. In such a case, install the latest
version you can download from the URL mentioned in
“Preparations” above.
Note
If you have lost or damaged the CD-ROM, you can
purchase a new one to replace it. Contact your Sony
service representative.
16
Using the CD-ROM Manual
Names and Functions of
Parts
2
Chapter
Front Panel
The names and symbols of buttons and knobs on the front
panel are color coded according to function.
White: Function when the button or knob is operated
independently.
Orange: Function when the button is operated with the
SHIFT button held down.
Blue: Function related to thumbnail operations.
1 On/standby button and
Handle
indicator
EJECT
7 Disc slot and EJECT
button
MARK1
PUSH SET(S.SEL)
ACCESS
2 ACCESS indicator
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
1 Audioleveladjustment
ALL CH
VAR/JOG
CH-2
section (see page 18)
RESET
CHAPTER
EXPAND
RETURN
3 Remote control switch
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
3 Shuttle/jog/variable
control section (see
SET
OFF
PB
HOME
4 KEY INHI switch
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
5 PHONES jack
DISC MENU
TOP
F REV
F FWD
END
STANDBY REC INHI
6 LEVEL adjustment knob
4 Display/menu control
section (see page 20)
a On/standby (1) button and indicator
When the POWER switch on the rear panel is in the @
position, and when DC power is connected to the DC IN
12V connector on the rear panel, this switches the unit
between the operating state (the indicator is lit green) and
the standby state (the indicator is lit red).
lights continuously red. If a disc is loaded in the unit, the
indicator flashes before changing to continuously lit red.
When using this unit, normally leave the rear panel
POWER switch in the @ (on) position, and use this button
to switch the unit between the operating state and standby
state.
When the indicator is lit red, pressing the button switches
this unit to the operating state, and the indicator lights
continuously green.
When the indicator is lit green, pressing the button
switches the unit to the standby state, and the indicator
b ACCESS indicator
This lights when the disc is accessed and when a file is
on/standby button is pressed while this indicator is lit,
17
Front Panel
1 Audio level adjustment section
access to the disc is completed before the unit switches to
the standby state.
1 CH-1/ALL CH, CH-2 to CH-4 adjustment knobs
Note
CH-1
CH-3
While the ACCESS indicator is lit, do not turn off the
POWER switch on the rear panel or disconnect the power
cord. This could lead to a loss of data from the disc.
ALL CH
CH-2
CH-4
c Remote control switch
Different positions of the switch allow different operations
VARIABLE KEY INHI
REC
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
as follows.
NET: Enables access to the network. The indicator lights
when an external network device is being accessed. In
this state, operation from the front panel is not
possible.
LOCAL: Enables operation from the front panel.
REMOTE: Enables remote control of this unit from the
following devices:
2 VARIABLE switch
a CH-1/ALL CH, CH-2 to CH-4 (audio level)
adjustment knobs
Depending on the setting of the VARIABLE switch, these
adjust the input audio or playback audio levels of channels
1 to 4.
• Devices connected to the REMOTE(9P) connector
on the rear panel
• Devices connected to the SD/HDSDI INPUT
connector with SDI remote control functions
• Devices connected to the (i.LINK) S400
connector
You can adjust levels of channels 5 to 8 using the function
By the setting of setup menu item 131 AUDIO VOLUME,
you can enable the CH-1/ALL CH adjustment knob to
simultaneously adjust all eight channels. When this
simultaneous adjustment is enabled, the ALL CH indicator
lights.
Use setup menu item 214 REMOTE INTERFACE to
select which of the connectors is used for remote control
about how to make extended menu settings.
b VARIABLE (audio level adjustment selector)
switch
This selects whether input audio levels or playback audio
levels are adjusted by the CH-1/ALL CH and CH-2 to CH-
4 adjustment knobs for channels 1 to 4, or by the function
menu setting for channels 5 to 8.
d KEY INHI switch
This turns key operation inhibit mode on or off.
Use setup menu item 118 KEY INHIBIT SWITCH
EFFECTIVE AREA to specify the keys to inhibit.
REC: Adjust the input audio levels. The playback audio
levels are fixed at their preset values.
PRESET: The audio levels are fixed at their preset values.
PB: Adjust the playback audio levels. The input audio
levels are fixed at their preset values.
e PHONES jack
The jack is a standard stereo jack. Connect stereo
headphones to monitor the audio during recording,
playback, and editing. (Non-audio signals are muted.) The
monitored channel is selected with MONITR L and
MONITR R on page P2 AUDIO of the function menu (see
2 Arrow buttons
The four arrow buttons are also used as the MARK1
button, MARK2 button, IN button, and OUT button. The
correspondence with these buttons is as follows.
V button: MARK1 button
f LEVEL (volume) adjustment knob
Adjust the volume of headphones or speakers with the
knob. You can also cause this to simultaneously adjust the
output volume from the AUDIO MONITOR R, L
connectors on the rear panel. To do this, set setup menu
item 114 AUDIO MONITOR OUTPUT LEVEL to “var”.
v button: MARK2 button
B button: IN button
b button: OUT button
You can use these buttons for thumbnail selection, menu
setting operations, setting In/Out points, and so on.
g Disc slot and EJECT button
Insert a disc in the disc slot. To remove the disc, press the
EJECT button.
18
Front Panel
3 Shuttle/jog/variable control section
1 V/MARK1 button and v/MARK2 button
2 IN indicator and OUT indicator
1 SHTL/JOG button
2 VAR/JOG button
MARK1
3 Jog/shuttle transport indicators
IN
OUT
SHTL/JOG
VAR/JOG
3 B/IN button and b/OUT button
RESET
MARK2
RETURN
L/JOG
a V/MARK1 button and v/MARK2 button
can use these for thumbnail selection.
During recording or playback, a shot mark 1 or shot mark
2 is recorded as an essence mark when you press the PUSH
SET (S.SEL) knob with the V/MARK1 or v/MARK2
button held down. If you connect a Windows USB
keyboard to the MAINTENANCE connector, you can
record shot marks from Shot Mark0 up to Shot Mark9 by
pressing the 0 to 9 keys on the numeric keypad.
Use the PDZ-1 Proxy Browsing Software on the supplied
XDCAM Application Software CD-ROM to delete and
modify essence marks.
5 Shuttle dial
4 Jog dial
For details of playback operations with these buttons and
a SHTL/JOG button
Press this button, turning it on, to perform shuttle playback
with the shuttle dial or jog playback with the jog dial.
When pressed during recording, stops recording and
selects shuttle/jog mode. If you do not want to stop
recording when this button is pressed, set setup menu item
145 MODE KEY ENABLE DURING RECORDING to
“stop”.
Essence marks can also be deleted and modified from the
Thumbnail Menu of the chapter thumbnail screen (see
b IN indicator and OUT indicator
IN indicator: When an In point is set, this lights. If an
attempt is made to set the In point after a recorded Out
point, this flashes.
b VAR/JOG button
Press this button, turning it on, to perform variable
playback with the shuttle dial or jog playback with the jog
dial.
OUT indicator: When an Out point is set, this lights. If an
attempt is made to set the Out point before a recorded
In point, this flashes.
When pressed during recording, stops recording and
selects variable/jog mode. If you do not want to stop
recording when this button is pressed, set setup menu item
145 MODE KEY ENABLE DURING RECORDING to
“stop”.
c B/IN button and b/OUT button
can use these for thumbnail selection.
An In or Out point is set when you press the PUSH
SET(S.SEL) knob with the B/IN or b/OUT button held
down. The In or Out point setting is deleted when you
press the RESET/RETURN button with the B/IN or b/
OUT button held down.
c Jog/shuttle transport indicators
These show the playback direction in jog, shuttle, or
variable speed mode.
b (green): Lights during playback in the reverse direction.
B (green): Lights during playback in the forward
direction.
x (red): Lights during still image display.
d Jog dial
Turn this for playback in jog mode. Turn clockwise for
forward direction playback, and counterclockwise for
reverse direction playback. In jog mode, the playback
speed varies from –1 to +1 times normal speed, according
to the rotation rate of the jog dial. There are no detents.
Normally, you press the SHTL/JOG or VAR/JOG button
before turning the jog dial, but it is also possible to make a
setting to enable jog mode directly by turning the dial (set
19
Front Panel
setup menu item 101 SELECTION FOR SEARCH DIAL
ENABLE to “dial”).
a Function buttons (F1 to F6)
These buttons are enabled when the function menu (see
page 48) is visible. Each press of a button changes the
setting of the corresponding item in the menu.
For convenience, this manual refers to these buttons as
buttons F1 to F6, in order from the top.
e Shuttle dial
Turn this for playback in shuttle mode or variable speed
mode. Turn clockwise for forward direction playback, and
counterclockwise for reverse direction playback.
• In shuttle mode, the playback speed varies in the range
20 times normal speed, according to the angular
position of the shuttle dial.
• In variable speed mode, you can finely adjust the
playback speed from –2 to +2 times normal speed,
according to the angular position of the shuttle dial.
The shuttle dial has a detent at the center position, for still
image playback.
b Display
Displays menus, audio level meters, and data such as time
data or clip information. The DISPLAY button lets you
switch to the video monitor display.
For details, see “Display window” on page 23.
c PUSH SET(S.SEL) knob
Normally, you press the SHTL/JOG button before turning
the shuttle dial, but it is also possible to make a setting to
enable shuttle mode directly by turning the dial (set setup
menu item 101 SELECTION FOR SEARCH DIAL
ENABLE to “dial”).
Use for menu and GUI screen operations. Turn the knob to
select items, and press it to confirm the selection. This
button is also used to set numerical and timecode values.
You can also change the playback speed by pressing the
PLAY button and turning this knob during playback (see
Note
information about how to use the thumbnail screens.
When setup menu item 101 SELECTION FOR SEARCH
DIAL ENABLE is set to “dial”, after using the shuttle dial,
return it to the center position. If the shuttle dial is not in
the center position, it is possible occasionally for vibration
from other operations to activate the dial, and start
playback in shuttle mode.
d MENU button
Displays the setup menu or the GUI screen menu. The
setup menu appears when no GUI screen is visible. The
same information is also superimposed on the display on a
monitor connected to the unit. Press once more to return to
the original display.
4 Display/menu control section
information about how to use the thumbnail screens.
5 RESET/RETURN button
4 MENU button
3 PUSH SET(S.SEL) knob
e RESET/RETURN button
1 Function buttons (F1 to F6)
Functions as the RESET button or the RETURN button.
RESET button: Reset counters or the setting values of the
timecode generator. This button is also used to abort
or cancel setup menu, scene selection, and thumbnail
search operations.
2 Display
RETURN button: In setup menu and GUI screens,
returns to the previous procedure.
f SUB CLIP/DISC MENU button and indicator
When pressed alone, functions as the SUB CLIP button.
When pressed together with the SHIFT button, functions
as the DISC MENU button.
SUB CLIP button: Press the button, lighting the
indicator, to carry out playback in clip list order (see
page 85). Jog and shuttle operations are supported
during clip list playback. To return to playback in
recording order, press the button again, turning the
indicator off.
6 SUB CLIP/DISC MENU button and
indicator
7 THUMBNAIL button and indicator
8 DISPLAY button
9 SHIFT button
0 PAGE/HOME button
qa EXPAND button
qs CHAPTER button
20
Front Panel
When this button is pressed together with the SHIFT
button, the unit returns to the previous division level.
Press the RESET/RETURN button to return to the
thumbnail screen.
Note
If no clip list is registered, this button does not light
when pressed. The operation is invalid.
This button also becomes a function button (F6) when the
function menu is visible.
DISC MENU button: When pressed together with the
Press the button again, turning the indicator off, to
hide the Disc Menu.
function.
information about how to use the thumbnail screens.
l CHAPTER button
When pressed during thumbnail display, displays a list of
thumbnails of the frames where essence marks are
recorded (chapter function). When this is pressed again,
returns to normal thumbnail display. The chapter function
can be useful when essence mark thumbnails provide more
information about the content of the clip than the index
pictures of the first frames. This can also be used to cue up
long clips.
g THUMBNAIL button and indicator
To carry out a thumbnail search or create a clip list in the
GUI screen, press this button turning the indicator on.
Thumbnail images representing each clip or sub-clip
appear. Press once more, turning the indicator off, to return
to a whole-screen display.
To display the thumbnails of essence mark frames (frames
with an essence mark attached), hold down the SHIFT
button, and press this button. The essence mark selection
menu appears. Select the desired type of essence mark, and
the corresponding essence mark frames appear in
thumbnails. Press once more, turning the indicator off, to
return to a whole-screen display.
This button also becomes a function button (F5) when the
function menu is visible.
function.
5 Recording and playback control section
information about how to use the thumbnail screens.
1 PREV button
2 PLAY button
3 NEXT button
h DISPLAY button
Each press of this button switches between the basic
This button is disabled unless either the basic operation
display or the video monitor display is displayed.
4 STOP button
5 REC button
PREV
PLAY
NEXT
STOP
REC
i SHIFT button
TOP
F REV
F FWD
END
STANDBY REC INHI
Switches between functions for any button with two
functions.
6 STANDBY indicator
7 REC INHI indicator
j PAGE/HOME button
When pressed alone functions as the PAGE switching
button. When pressed together with the SHIFT button,
functions as the HOME button.
PAGE button: Displays the function menu, if it is not
already visible. (The most recently displayed page of
the function menu appears.)
HOME button: When pressed with the function menu
visible, returns to the HOME page of the function
menu.
a PREV (previous) button
Press this button, turning it on, to show the first frame of
the current clip. While the first frame of a clip is shown,
pressing this button jumps to the beginning of the previous
1)
clip.
This button is also used together with other buttons
for the following operations.
Reverse direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the reverse direction is carried out.
Displaying the first frame of the first clip: Hold down
the SHIFT button, and press this button.
k EXPAND button
When pressed during thumbnail display, divides the
selected clip into 12 blocks and displays a list of
thumbnails of the first frame in each block (expand
function). The division is repeated with each press (up to 3
times, for a total of 1,728 blocks).
1) When setup menu item 153 FIND MODE is set to “clip & rec start mark”,
this button jumps to the frame where the previous Rec Start essence mark
is set and displays the video of that frame.
21
Front Panel
b PLAY button
f STANDBY indicator
To start playback, press this button, turning it on.
When pressed during recording, stops recording and enters
stop mode. If you do not want to stop recording when this
button is pressed, set setup menu item 145 MODE KEY
ENABLE DURING RECORDING to “stop”.
Lights when the unit is in standby mode (STOP button and,
STANDBY indicator lit).
After a certain time passes in a disc stop mode, the unit
automatically enters standby off mode and the indicator
goes off.
c NEXT button
Press this button, turning it on, to jump to the next clip, and
show the first frame. This button is also used together
You can specify the time until the unit enters standby off
mode. For details, see the description of setup menu item
1)
with other buttons for the following operations.
Forward direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the forward direction is carried out.
Displaying the last frame of the last clip: Hold down the
SHIFT button, and press this button.
g REC INHI (recording inhibit) indicator
This lights in the following cases.
• When a disc with recording inhibited is loaded.
• When REC INH on the HOME page of the function
menu is set to “ON”.
• The format of the recorded part of the disc does not
match the system frequency settings of the unit.
1) When setup menu item 153 FIND MODE is set to “clip & rec start mark”,
this button jumps to the frame where the next Rec Start essence mark is set
and displays the video of that frame.
d STOP button
To stop recording or playback, press this button, turning it
on. The frame at the stop point appears.
The unit enters standby off mode when you press this
button with the SHIFT button held down. It returns from
standby off mode to the original state when you press this
button again with the SHIFT button held down. (The lit or
unlit status of the STOP button does not change.)
Note
This button flashes when setup menu item 105
REFERENCE SYSTEM ALARM is set to “on” and the
correct reference video input signal (as specified by OUT
REF on page P6 REF of the function menu) is not being
input.
This unit can automatically enter standby off mode
whenever a specified time elapses in disc stop mode. For
details, see the description of setup menu item 501 STILL
e REC (record) button
To start recording, hold down this button, and press the
PLAY button. The recording takes place on an unrecorded
part of the disc.
To stop recording, press the STOP button.
To monitor in E-E mode
You can press this button from stop mode to monitor input
signals in E-E mode. The button lights when pressed. Press
the STOP button to return to the original video.
You can also press this button during playback and
searches. E-E mode playback continues for as long as the
button is held down.
22
Front Panel
Display window
Basic operation display
1 Audio input display/
a)
Audio level meters
6 Disc information
2 Function menu
7 System information
3 Clip information
8 Format conversion
4 Recording format
5 Time data display area
9 Reference signal
q; Video input display
a) The mixing display appears only on the PDW-F1600
(see the following figure).
a Audio input display/Audio level meters
Displays information about audio. There are two display
mode, which can be switched over using AU METER on
page P4 AUDIO of the function menu.
modes for the audio level meter: FULL mode and FINE
Meter display mode: FULL
Meter display mode: FINE
A Input signal display
H Meter display mode
B Data indication
DATA
DATA
AES/EBU
AES/EBU HD-SDI
HD-SDI
FINE
2
1
0
2
1
0
-1
-2
-1
-2
L
R
1
2
3
4
G Level bar
F Reference level
E Audio channel
D Monitor channel
C F1600 Mixing
A Input signal display: Displays the audio input signal.
23
Front Panel
.
Display
ANA-1
ANA-2
MIC-1
MIC-2
Input signal
All remaining clips or clip list playback time
Total number of clips recorded on disc
Analog audio
signal
Channel 1, 3
Channel 2, 4
Input signal from Channel 1, 3
the microphone
Channel 2, 4
connected to
ANALOG
AUDIO INPUT
connector
PDW-HD1500
001/001 000:00
Number of current clip
Clip name
AES/EBU
HD-SDI
SD-SDI
SG
AES/EBU format digital audio signal
(flashes when there is no input signal)
d Recording format
Displays the system frequency and the video and audio
formats.
HDSDI audio signal (flashes when
there is no input signal)
SDSDI audio signal (flashes when
there is no input signal)
59.94i HD422-1080 50Mbps 8CH-24BIT
Test signal from the internal signal
generator
Audio format
No indication Undefined audio signal, or no audio
input
Video format
System frequency
B Data indication: Appears when the input signals are
non-audio signals.
C
Mixing: Displays the input channels used for
audio mixing. (These channels are selected with setup
F1600
e Time data display area
menu item 819 AUDIO INPUT ARRANGE.)
A Remaining disc recording capacity
D Monitor channel: Displays the audio monitoring
channels set with MONITR L and MONITR R on
E Audio channel: Displays the audio channels.
Also indicates preset or variable mode by its color
B Rec Run/Free Run
C Timecode generator mode
D VITC
E Time data type
White: Preset mode
Green: Variable mode
F Reference level: Displays the reference level for
recording as set in the maintenance menu.
G Level bars: Display the audio recording or playback
levels of channels 1 to 8. The OVER indicators light
when the audio level exceeds 0 dB.
F Time data
G Recording mode indication
H Meter display mode: Displays the audio level meter
display mode selected with AU METER on page P4
A Remaining disc recording capacity: Displays the
amount of recording capacity remaining on the disc.
B Rec Run/Free Run: Displays the timecode run mode.
The run mode is set with RUN MODE on page P5 TC
C Timecode generator mode: Displays the timecode
source and generation method (preset or regenerate).
These are set with PRST/RGN and TCG on page P5
b Function menu
Use the PAGE/HOME button to display this menu, and to
1)
switch between the pages (HOME, P1 to P7, (P8) ,
1)
(HOME2) ) of the menu. Each page has three to six
setting items. Press the corresponding button to change a
setting.
D VITC: Lights in the following cases.
1) If a menu item is assigned using maintenance menu item M38: F-KEY
CONFIG
• When VITC is read in playback mode. (This has no
relations to the display in the time data display
area.)
For details, see page 48 “Basic Operations of the
• When VITC recording is possible.
E Time data type: Displays the type of time data
displayed in the time data display area. The type of
time data is selected with CNTR SEL on the HOME
c Clip information
Displays clip information.
24
Front Panel
Display
TC
Type of time data
Timecode
Display
Usable format
HD422: HD422
HD420: HD420HQ/HD420SP/HD420LP
a)
COUNTER
UB
Elapsed recording/playback time
User bits
a) HD420LP supports playback only.
VITC
VITC
VIUB
TCG
VIUB
When the PDBK-S1500 option is installed
Timecode generator value
User bits generator value
Display
Usable format
UBG
HD422: HD422
a)
F Time data: Normally displays timecode or VITC,
according to the selection made with TCR on page P5
TC of the function menu.
G Recording mode indication: This appears when setup
menu item 150 REC MODE is set to “disc exchange
cache” or “clip continuous rec” (see page 130).
HD420: HD420HQ/HD420SP/HD420LP
IMX: MPEG IMX 50Mbps/40Mbps/
30Mbps
DVCAM: DVCAM
a) HD420LP supports playback only.
exchange cache function.
B System frequency: Displays the system frequency of
the clips recorded on the disc.
Continuous Rec function.
C Video format: Displays the video format and bitrate of
the clips recorded on the disc.
D Audio format: Displays the audio format of the clips
recorded on the disc.
f Disc information
g System information
A Disc loaded indication/usable
format
A Power status
B System frequency
59.94i
B Menu setting status
C Clip playback format
DEFAULT
422-1080
50Mbps
C Remote interface
RM-9P
REPEAT
D Audio format
8CH-24BIT
D Clip playback mode
E Jog/shuttle dial mode
SHTL/JOG
A Disc loaded indication/usable format: When a disc is
loaded in this unit, a disc loaded indication appears.
When no disc is loaded, the usable formats are
displayed.
A Power status: Displays the status of the power supply
to the unit.
Display
Power status
The background color of the disc loaded mark
indicates one of the following disc states.
Blue: Disc capable of recording and playback.
Yellow: Disc capable of playback only.
AC power
Battery
Red: Disc incapable of recording and playback.
Battery almost exhausted: Flashes at 1 Hz
Battery exhausted: Flashes at 4 Hz
Note
AC power (power-saving mode)
Battery (power-saving mode)
Battery (power-saving mode/low)
Even if the background is blue, recording is not
possible in the following cases.
• When a disc with recording inhibited is loaded.
• When REC INH on the HOME page of the function
menu is set to “ON”.
B Menu setting status: Displays the current setting
The usable formats displayed when no disc is loaded
in this unit are as follows.
status of setup menu.
25
Front Panel
INPUT: Input video
HD REF: HD-format reference signal
SD REF: SD-format reference signal
Display
Description
BANK1
The current menu settings are the same
as the settings in menu bank 1.
BANK2
The current menu settings are the same
as the settings in menu bank 2.
Note
The HD REF or SD REF display flashes when the video
input signal is not synchronized to the reference signal, and
when the signals are synchronized but their phases do not
match.
BANK3
The current menu settings are the same
as the settings in menu bank 3.
DEFAULT
The current menu settings are the same
as the factory defaults.
No display The current menu settings are different
from all of the above.
j Video input display
This displays the currently selected video input signal.
C Remote interface: When the remote control switch is
set to REMOTE, displays the name of the interface
selected with setup menu item 214 REMOTE
INTERFACE.
HDSDI: HDSDI video input
SDSDI: SDSDI video input
i.LINK: i.LINK TS (HDV) input
SG: Test video signal from the internal signal generator
1)
D Clip playback mode: The clip playback mode appears
as follows, according to the settings of setup menu
items 142 REPEAT MODE and 154 SINGLE CLIP
PLAY MODE.
1) When the PDBK-201 option board is installed
Note
The display blinks when there is no video input signal, and
when the video input signal does not match the system
frequency of this unit.
Display Setup menu setting Description
Item 142 Item 154
REPEAT play
off
on
on
Repeat playback
mode: Perform
repeat playback of
all clips on the disc.
The video signal input is selected with V INPUT on page
SINGLE off
Single clip playback
mode: Play the
currently selected
clip once.
Video monitor display
A Audio level meters
SNGL
RPT
play
off
Single clip repeat
playback mode:
Play the currently
selected clip
0
0
-10
-20
-10
-20
repeatedly.
-30
-40
-30
-40
-60
-60
No
off
Continuous
1
2
3
4
display
playback mode:
Perform continuous
playback of all clips
on the disc, playing
each clip once.
TCR.00:45.39.18*
JOG
STILL
DC-SQ
B Superimposed information
E Jog/shuttle dial mode: Appears when the unit is in
shuttle, jog, or variable mode.
C Recording mode indication
h Format conversion
This displays the status of 1080/720 format conversion.
D Low battery warning
E Converter display
: Format conversion is not being performed.
FC
: Format conversion is being performed.
When you press the DISPLAY button, the display window
changes to the video monitor display.
A Audio level meters: LEVEL MT on page P2 AUDIO
of the function menu decides whether the meter is to
be displayed and on which side, left or right, it is
displayed in the display window.
B Superimposed information: Appears when CHAR
SEL on the HOME page of the function menu is set to
“ON” or “LCD”.
convert function.
i Reference signal
This displays the type of reference signal to which this unit
is synchronizing.
When there is no display, the unit is synchronizing to the
internal reference signal.
26
Front Panel
C Recording mode indication: This appears when setup
menu item 150 REC MODE is set to “disc exchange
cache” or “clip continuous rec” (see page 130).
exchange cache function.
Continuous Rec function.
D Low battery warning: Appears and flashes during
operation with a battery pack when the battery power
is almost exhausted.
E Converter display: Displays the current down- or up-
converter mode, depending on the state of the unit.
The current down-converter (DC) mode appears
when HD video is being input and when an HD disc
is being played. The current up-converter (UC) mode
appears when SD video is being input and when an
1)
SD disc is being played.
The current modes are those selected with setup menu
items 930 DOWN CONVERTER MODE (DC) and
1)
950 UP CONVERTER MODE .
1)When the PDBK-S1500 option is installed.
DC-EC: Down-converter edge-crop mode
DC-LB: Down-converter letter box mode
DC-SQ: Down-converter squeeze mode
UC-EC: Up-converter edge-crop mode
UC-LB: Up-converter letter box mode
UC-SQ: Up-converter squeeze mode
27
Front Panel
Rear Panel
=
DC IN 12V
POWER
AC IN
REMOTE
4 DC IN 12V connector
5 REMOTE connector
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
1
2
2
R
L
6 SD/HDSDI INPUT connector
2 Analog audio signal input/
output section (see
7 HDSDI OUTPUT 1, 2
(SUPER) connectors
DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT
HDSDI OUTPUT
IN
1/2
3/4
1
2
(SUPER)
8 COMPOSITE OUTPUT1, 2
COMPOSITE OUTPUT
(SUPER)
REF.VIDEO INPUT
IN
(SUPER) connectors
3 Digital audio signal input/
output section (see
1
2
OUT
SDSDI OUTPUT
1
9 REF.VIDEO INPUT
2
(SUPER)
connectors
1/2
3/4
TIME CODE
MAINTENANCE
S400
VIDEO CONTROL
REMOTE(9P)
IN
OUT
4 Timecode input/output
1
(i.LINK) S400 connector
section (see page 30)
0
(network) connector
2 VIDEO CONTROL connector
qa MAINTENANCE connectors
3 REMOTE(9P) connector
qs SDSDI OUTPUT1, 2
(SUPER) connectors
a
(i.LINK) S400 connector (6-pin, IEEE1394
compliant)
d DC IN 12V connector (XLR 4-pin, male)
Connect to a DC power source of 12 V.
Connect a computer or other device, using an i.LINK
cable.
When using the BKP-L551 Battery Adaptor to mount a
battery pack, connect the power cable of the BKP-L551.
When the PDBK-201 option board is installed, i.LINK TS
(HDV) signals can be input and output via this connector.
e REMOTE connector (4-pin)
Supplies power to the RM-280 Editing Controller.
Notes
• When this unit is connected to a device with a 6-pin
i.LINK connector by an i.LINK cable, before
f SD/HDSDI INPUT (SDSDI/HDSDI signal input)
connector (BNC type)
This inputs an SDSDI or HDSDI format video/audio
unplugging the i.LINK cable, first power off the device
and disconnect the power plug from the outlet. If the
i.LINK cable is unplugged with the device power plug
still connected, a current from an excessive voltage (8 to
40 V) output from the i.LINK connector of the device
flows into this unit. This may cause a failure of the unit.
• When connecting this unit to a device with a 6-pin
i.LINK connector, connect to the 6-pin i.LINK
connector of the other device first.
signal.
g HDSDI OUTPUT 1, 2 (SUPER) (HDSDI signal
output 1, 2 (superimpose)) connectors (BNC type)
These output HDSDI format video/audio signals.
When editing with two PDW-HD1500 units, connect a
cable between these connectors on the player unit and the
SD/HDSDI INPUT connector on the recorder unit.
You can superimpose timecodes, menu settings, error
messages, or other information on the output of the HDSDI
OUTPUT 2 (SUPER) connector with the setting for
CHAR SEL on the HOME page of the function menu or
with the setting for setup menu item 028 HD
b VIDEO CONTROL connector (D-sub-9-pin)
Connect an HKDV-900 video control unit.
HKDV-900 and setup menu of this unit.
CHARACTER. You can always disable to superimpose
the data independent of the setting for CHAR SEL with the
setting for setup menu item 028.
c REMOTE(9P) (remote control 9-pin) connector
(D-sub 9-pin)
To control this unit from a controller or VTR supporting
the RS-422A Sony 9-pin VTR protocol, connect the device
to this connector.
for more information about the CHAR SEL settings.
28
Rear Panel
item 028 HD CHARACTER.
l SDSDI OUTPUT 1, 2 (SUPER) (SDI signal outputs
1, 2 (superimpose)) connectors (BNC type)
These output SDSDI format video/audio signals.
When the unit is shipped from the factory, audio signal
output is eight channels with no switching, and RP188
timecode output is set to on. You can change these settings
with setup menu item 828 SDI AUDIO OUTPUT
SELECT and setup menu item 920 SD-SDI H-ANC
CONTROL.
To treat the input and output signals of these connectors as
non-audio signals, set the maintenance menu item M37:
AUDIO CONFIG >M372: NON-AUDIO INPUT
AUDIO FLAG PB (playback).
The output from the 2 (SUPER) connector can have
timecode, menu settings, alarm messages, and other text
information superimposed. To turn superimposition off,
set CHAR SEL on the HOME page of the function menu
to “OFF”.
h COMPOSITE OUTPUT 1, 2 (SUPER) (analog
composite video output 1, 2 (superimpose))
connectors (BNC type)
Output analog composite video signals. You can
superimpose timecodes, menu settings, or error messages
on the output of the 2 (SUPER) connector when CHAR
SEL on the HOME page of the function menu is set to ON.
information.
for more information about the CHAR SEL setting.
for more information.
i REF.VIDEO INPUT (reference video signal input)
connectors (BNC type)
1 Power supply section
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector, the
same signal is input from the right connector (
) to a
1 POWER switch
connected device. When no connection is made to the right
connector, the left connector is automatically terminated
with an impedance of 75 ohms.
2 - AC IN connector
POWER
AC IN
j
(network) connector (RJ-45 type)
This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
a POWER (main power) switch
Press the : side to power on the unit. Press the a side to
power off.
When using the unit, normally leave the POWER switch in
the : (on) position, and use the on/standby button on the
front panel to switch the unit between the operating state
and standby state.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive à ce port. Suivez les instructions pour ce port.
Note
Before turning the main power off, always check to be sure
that the unit is in the standby state, and then press the main
power switch to the a side.
ACHTUNG
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-
Anschluss verbinden, der zu starke Spannung für diese
Buchse haben könnte. Folgen Sie den Anweisungen für
diese Buchse.
b -AC IN connector
Connect to an AC power supply with the power cord (not
supplied).
k MAINTENANCE connectors
These are the USB connectors for maintenance.
Connect a Windows USB keyboard or mouse (see
page 81), or a USB flash drive to access planning metadata
29
Rear Panel
2 Analog audio signal input/output section
for more information.
1 ANALOG AUDIO INPUT 1, 2 connectors
3 Digital audio signal input/output section
2 ANALOG AUDIO OUTPUT 1, 2
connectors
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
R
1
2
2
L
1 DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4
connectors
DIGITAL AUDIO (AES/EBU)
IN
1/2
3/4
OUT
3 AUDIO MONITOR R, L connectors
1/2
3/4
a ANALOG AUDIO INPUT 1, 2 connectors (XLR 3-
pin, female)
2 DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4
connectors
These input analog audio signals.
With A1 INPUT or A2 INPUT on page P2 AUDIO, and
A3 INPUT or A4 INPUT on page P3 AUDIO of the
signal input to connector 1 is assigned to audio channel 1or
3, and whether the signal input to connector 2 is assigned
to audio channel 2 or 4.
You can set the reference input level with the maintenance
(Factory default setting: +4 dB)
a DIGITAL AUDIO (AES/EBU) IN (digital audio
input) 1/2, 3/4 connectors (BNC type)
These input AES/EBU format digital audio signals. The
left connector (1/2) corresponds to audio channels 1 and 2,
and the right connector (3/4) corresponds to audio
channels 3 and 4.
b DIGITAL AUDIO (AES/EBU) OUT (digital audio
output) 1/2, 3/4 connectors (BNC type)
These output AES/EBU format digital audio signals.
When the unit is shipped from the factory, the 1/2
connector is set to audio channel 1/2, and the 3/4 connector
is set to audio channel 3/4. You can change these settings
with setup menu item 827 AES/EBU AUDIO OUTPUT
Microphone settings
If you have connected a microphone to this unit, you can
set input level, AGC, and limiter values for the
microphone with setup menu items 834, 839, 840, and 841
Note
To treat the input and output signals of these connectors as
non-audio signals, set the maintenance menu item M37:
AUDIO CONFIG >M372: NON-AUDIO INPUT
AUDIO FLAG PB (playback).
An unpleasant sound may be output if you have connected
a microphone to the ANALOG AUDIO INPUT 1 or 2
connector and power the microphone on with the input
level too high. Check the input level setting before
connecting a microphone.
4 Timecode input/output section
b ANALOG AUDIO OUTPUT 1, 2 connectors (XLR
3-pin, male)
These output analog audio signals.
1 TIME CODE IN connector
When the unit is shipped from the factory, the 1 connector
is set to audio channel 1, and the 2 connector is set to audio
channel 2. You can change these settings with setup menu
item 824 ANALOG LINE OUTPUT SELECT (see
2 TIME CODE OUT
connector
TIME CODE
IN
OUT
You can set the output level with the maintenance menu
default setting: +4 dB)
a TIME CODE IN connector (BNC type)
This inputs an SMPTE timecode generated by an external
device.
Non-audio signals are muted.
c AUDIO MONITOR R, L connectors (XLR 3-pin,
male)
This outputs an audio signal for monitoring.
The monitored channel is selected with MONITR L and
MONITR R on page P2 AUDIO of the function menu.
b TIME CODE OUT connector (BNC type)
This outputs the following timecode, depending on the
operating state of this unit.
During playback: Playback timecode
30
Rear Panel
During recording: The timecode from the internal
timecode generator or the timecode input to the TIME
CODE IN connector
When setup menu item 611 TC OUTPUT PHASE IN EE
MODE is set to “muting”, no timecode is output.
31
Rear Panel
Preparations
3
• Before using the batteries, be sure to charge them fully
with the special battery charger. Refer to the operating
instructions for your battery charger for more
information about how to charge the batteries.
• Batteries may not be completely charged if you charge
them immediately after use when they are still warm.
You should wait until the batteries cool before charging
them.
Chapter
Continuous recording time at room temperature
BP-GL95 lithium-ion battery pack: 80 minutes (95
minutes when used in power save mode)
Preparing Power Sources
For details on charging battery packs, refer to the
operation manual for the battery charger.
This unit can be powered by AC power, DC power, or a
battery pack.
For safety, use only the Sony battery packs listed below.
Lithium-ion battery pack: BP-L80S, BP-GL95
Notes about battery usage
Note
If you load or remove a battery pack incorrectly, it may fall
and cause bodily injury. Follow the procedures described
below to load or remove them.
Supplying power
Attaching a battery pack
AC power supply
Attaching and removing of the BP-GL95 Battery Pack is
described below.
The BP-L80S can also be attached and removed in the
same way.
Connect the AC IN connector to an AC power source using
the specified AC power cord. To supply AC power to the
unit, set the on/standby button on the front panel to ON and
the POWER switch on the rear panel to = (ON).
For details on attaching the BKP-L551, refer to the
installation manual for the BKP-L551.
DC power supply
Connect the DC IN 12V connector to a DC power source.
To supply DC power to the unit, set the on/standby button
on the front panel to ON and the POWER switch on the
rear panel to OFF. If the POWER switch on the rear panel
is set to = (ON), AC power is supplied.
1
Attach the BKP-L551 to the side panel.
Battery power supply
Battery packs that can be used with this unit are as follows.
To use battery pack, a BKP-L551 Battery Adaptor and a
BC-L100 Battery Charger are also required.
• BP-L80S
BKP-L551
• BP-GL95
2
Align the grooves on the BP-GL95 with the
projections on the BKP-L551.
32
Preparing Power Sources
Initial Setup
This unit is shipped with the area of use, system frequency,
recording format, and current date and time still unset.
Therefore, you need to make initial setup settings before
using the unit. (You cannot use the unit without setting it
up.)
BP-GL95
Once the unit has been set up, the settings are retained even
when the unit is powered off.
3
Slide the BP-GL95 as shown below so that the
connectors on the BP-GL95 and the BKP-L551 are
connected.
Use the following procedures.
POWER
AC IN
1
EJECT
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
4
Connect the DC cable of the BKP-L551 to the DC IN
12V connector.
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
Removing the battery pack
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
With the lever pushed in, slide the BP-GL95 out as shown
below.
5,6
2,3,4 5
1
Power the unit on.
The INITIAL SETUP screen appears on the display.
RETURN
INITIAL SETUP
UC/J MODEL
SELECT
Lever
NONE
Checking the remaining battery power
You can use the LEDs on the side panel of the battery to
check the remaining power of the battery.
SET
INC/DEC : CTRL.KNOB
F1(RET)
F5(SET)
CANCEL&PREV :
SET&NEXT :
INIT
2
3
Turn the PUSH SET(S.SEL) knob to select the area of
use.
Display UC (for regions outside Japan) or J (for
Japan), and then press the SET function button (F5).
The system frequency screen appears.
Turn the PUSH SET(S.SEL) knob to select the system
frequency.
33
Initial Setup
RETURN
RETURN
INITIAL SETUP
INITIAL SETUP
SYSTEM FREQUENCY
SELECT
Push F5(SAVE) Key!!
1080/50i
SET
SET
INC/DEC : CTRL.KNOB
F1(RET)
F5(SET)
CANCEL&PREV :
SET&NEXT :
CANCEL&PREV :
SAVE&REBOOT :
F1(RET)
F5(SET)
INIT
INIT
Display the system frequency that you want to use, and
then press the SET function button (F5).
The DATE/TIME PRESET screen appears.
The message “NOW SAVING...” appears again, and
the setting screen disappears. Then the unit powers
itself off and on again.
To return to the original screen without saving
settings
Press the RETURN function button (F1).
4
In the DATE/TIME PRESET screen, set the current
date and time by setting the following items.
RETURN
DATE/TIME PRESET
Note
YEAR
MONTH
DAY
2008
11
19
The time zone is reset to the factory default when you
execute the maintenance menu item M49: RESET ALL
SETUP. You will need to set it again. The date and time
are not reset.
TIME 16:49:00
TIME ZONE UTC+00:00
SET
INC/DEC : CTRL.KNOB
SHIFT : (P)(p)KEY
CANCEL&PREV :
SET&NEXT :
F1(RET)
F5(SET)
INIT
YEAR: Year
MONTH: Month
DAY: Day
TIME: Time
TIME ZONE: Time zone (as a difference in hours
with respect to Coordinated Universal Time
(UTC))
In the setting screen, you can change the value of the
flashing digit.
Press the B/IN or b/OUT button to make the previous
digit or next digit start flashing.
Press the V/MARK1 or v/MARK2 button (or turn the
PUSH SET(S.SEL) knob) to increment or decrement
the value of the flashing digit.
When you have finished making settings, press the
SET function button (F5).
The date, time, and time zone settings are saved, and
the message “NOW SAVING...” appears.
5
If you want to save the settings made up to this point,
press the SET function button (F5) again.
34
Initial Setup
To change the angle of the front panel
To change the angle to position 2 from position 1, pull the
front panel out to position 2.
To change the angle to position 1 from position 2, first
unlock the front panel by pulling it all the way out to the
return position. Then return it to position 0, and pull out
again to position 1.
Front Panel Tilt
Mechanism
The front panel of this unit has a tilt mechanism that allows
you to pull the front panel out and adjust it to a convenient
angle.
To pull the front panel out
Grasp the holds (small protrusions) on both sides of the
front panel and pull out as indicated by the arrow.
You can fix the angle of the front panel in position 1 (15
degrees) or position 2 (40 degrees).
Return position
Position 2 (40 degrees)
Position 1 (15 degrees)
Position 0
Note
The angle cannot be fixed if you pull the front panel past
position 2 all the way out to the return position. To fix the
front panel, return it to position 0 and then pull it out to
position 1 or position 2.
To return the front panel to its original
position
Unlock the front panel by pulling it out to the return
position. You can then return it to position 0.
35
Front Panel Tilt Mechanism
Settings on this unit
Connections and
Settings
Remote control switch: NET (see page 18)
Setup menu item 257 NETWORK ENABLE: net
Connecting three PDW-F1600 or PDW-HD1500
units to a laptop computer via a LAN
Note
PDW-F1600 or
PDW-HD1500
Production of some of the peripherals and related devices
described in this chapter has been discontinued.
For advice about choosing devices, please contact your
Sony dealer or a Sony sales representative.
Laptop computer
Connections for using PDZ-1 Proxy
Browsing Software
LAN
You can use the PDZ-1 Proxy Browsing Software on the
supplied XDCAM Application Software CD-ROM to
carry out simple editing with proxy AV data.
Network cable
(not supplied)
For an overview of PDZ-1 and how to install the software,
page 170. For information about how to use the software,
refer to the Help provided in the software.
To
connector
(network)
Settings on all PDW-HD1500
Using the
connection)
The following shows an example of an FTP (File Transfer
Protocol) connection.
(network) connector (FTP
Remote control switch: NET (see page 18)
Setup menu item 257 NETWORK ENABLE: net
Using the (i.LINK) S400 connector (FAM
connection)
Note
The following shows an example of a FAM (file access
mode) connection.
To use PDZ-1 requires the PDW-F1600 or PDW-HD1500
IP address and other network-related settings to be made
beforehand.
Note
For details of the network-related settings, see “To change
The PDZ-1 Proxy Browsing Software must be installed in
advance.
The required FAM driver is also installed when you install
the PDZ-1 software.
Connecting this unit directly to a laptop computer
PDW-F1600 or PDW-
HD1500 (this unit)
for more information about installing the PDZ-1 software.
Laptop computer
Some limitations apply to FAM connections. For details,
To
(network) connector
Network cable (not supplied)
36
Connections and Settings
Use of a shielded cable is recommended.
PDW-F1600 or PDW-
HD1500 (this unit)
Laptop computer
To S400 connector
i.LINK cable (not supplied)
Connections for cut editing
The following figure shows a cut editing system
comprising this unit as a player.
When making the connections, also refer to the manuals
provided with the equipment to be connected.
unit settings.
When using an editing control unit
Using BVE-700/700A
The following figure shows a cut editing system
comprising this unit as a player, an HDW-M2000/M2000P
unit as a recorder, and a BVE-700/700A as an editing
control unit.
37
Connections and Settings
1: 75Ω coaxial cable (not supplied)
HD video monitor
2: 9-pin remote control cable (not supplied)
To HDSDI input connector
HDSDI OUTPUT 2
(SUPER)
1
PDW-F1600 or
PDW-HD1500
(this unit, player)
=
DC IN 12V
POWER
AC IN
REMOTE
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
1
2
2
R
L
REF.VIDEO
INPUT
DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT
HDSDI OUTPUT
Reference video signal
IN
1/2
3/4
1
2
(SUPER)
COMPOSITE OUTPUT
(SUPER)
REF.VIDEO INPUT
IN
1
2
REF.VIDEO
INPUT
OUT
SDSDI OUTPUT
1
2
(SUPER)
1/2
3/4
TIME CODE
MAINTENANCE
S400
VIDEO CONTROL
REMOTE(9P)
IN
OUT
1
HDSDI
REMOTE(9P)
OUTPUT1
2
REF VIDEO
INPUT
HDSDI
INPUT
1
HDW-M2000 (recorder)
PLAYER-1
75Ω
REF VIDEO
INPUT
SDI OUT
SDI IN
AC IN
MONITOR
OUT
VIDEO
OUT2
VIDEO
OUT1
AUX/
TITLE
RECORDER
PLAYER-2
PLAYER-1
PLAYER-1
PLAYER-3
1
SWER
MIXER
RECORDER
PLAYER-3
PLAYER-2
NETWORK
PANEL
GPI
EDL
REF VIDEO IN
REF
RECORDER
VIDEO IN
BVE-700/700A
(editing control unit)
HDSDI
OUTPUT 3
(SUPER)
REMOTE 1-IN(9P)
To HDSDI input
connector
1
2
HD video monitor
HDW-M2000 (recorder) settings
BVE-700/700A (editing control unit)
setting
Settings on this unit
REMOTE 1 (9P) button: Lit
SYNCHRONIZE menu:OFF
Remote control switch: REMOTE (see
REF.VIDEO INPUT connector 75 Ω
termination switch: OFF
Setup menu item 214 REMOTE
INTERFACE: 9PIN
Audio selection function switching button
INPUT button: HDSDI
Function menu HOME >F1 (VID. IN): SDI
Function menu page 1 >F1 (TCG): INT
Function menu page 1 >F2 (PR/RGN):
PRESET
Function menu page 1 >F3 (RUN): FREE
38
Connections and Settings
Editing Control Unit Settings
When connecting an editing control unit (BVE-700/700A/
2000) to use with this unit, set VTR constants as follows.
F1600
System
frequency
VTR CONSTANT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
a)
a)
59.94i/
59.94P/
29.97P
A0
97
00
96
03
80
0A
07
FE
00
80
5A
FF
5A
07
07
a)
a)
a)
a)
50i/50P/25P A1
23.98P A2
97
97
00
00
7D
78
03
03
80
80
0A
0A
07
07
FE
FE
00
00
80
80
4C
48
FF
FF
4B
48
07
07
07
07
a) This is 15 when maintenance menu item M393: AUDIO DSP is set to
“AGC/limiter”.
HD1500
.
System
frequency
VTR CONSTANT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
59.94i/
59.94P/
29.97P
A0
96
00
96
15
15
03
80
0A
07
FE
00
80
5A
FF
5A
50i/50P/25P A1
96
96
00
00
7D
78
15
15
15
15
03
03
80
80
0A
0A
07
07
FE
FE
00
00
80
80
4C
48
FF
FF
4B
48
a)
A2
23.98P
a) When the PDBK-F1500 option is installed.
Using RM-280
The following figure shows a cut editing system
comprising a PDW-HD1500 as a player, a PDW-F1600
unit as a recorder, and an RM-280 as an editing controller.
39
Connections and Settings
1: 75Ω coaxial cable (not supplied)
HD video monitor
2: 9-pin remote control cable (not supplied)
To HDSDI input connector
HDSDI OUTPUT 2
(SUPER)
1
=
DC IN 12V
POWER
AC IN
PDW-HD1500 (player)
REMOTE
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
1
2
2
R
L
REF.VIDEO
INPUT
1
DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT
HDSDI OUTPUT
IN
1/2
3/4
1
2
(SUPER)
Reference video signal
COMPOSITE OUTPUT
(SUPER)
REF.VIDEO INPUT
IN
1
2
OUT
SDSDI OUTPUT
1
2
(SUPER)
1/2
3/4
TIME CODE
MAINTENANCE
S400
VIDEO CONTROL
REMOTE(9P)
IN
OUT
HDSDI
REMOTE(9P)
OUTPUT1
1
REF VIDEO
INPUT
PDW-F1600
(recorder)
SD/HDSDI
INPUT
=
POWER
AC IN
DC IN 12V
2
REMOTE
REMOTE(9P)
RECORDER(DEVICE2)
ANALOG AUDIO INPUT
1
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
2
2
R
L
RM-280
(editing
controller)
REF.VIDEO
INPUT
(
)
REMOTE 9P
REC TALLY
OUTPUT
REF
IN OUT
DC IN
/
(
)
1
(
)
2
RECORDER DEVICE
PLAYER DEVICE
RS232C
DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT
HDSDI OUTPUT
IN
1/2
3/4
1
2
(SUPER)
1
COMPOSITE OUTPUT
(SUPER)
REF.VIDEO INPUT
IN
1
2
OUT
SDSDI OUTPUT
1
2
(SUPER)
1/2
3/4
REF.VIDEO
INPUT
REMOTE(9P)
RECORDER(DEVICE1)
REF IN/OUT
TIME CODE
MAINTENANCE
S400
VIDEO CONTROL
REMOTE(9P)
IN
OUT
HDSDI
To HDSDI input
connector
REMOTE(9P)
1
OUTPUT 2
(SUPER)
2
1
HD video monitor
PDW-F1600 (recorder) settings
RM-280 (editing controller) settings
PDW-HD1500 (player) settings
Remote control switch: REMOTE
EDITOR/REMOTE CONTROL selector
switch: EDITOR
Remote control switch: REMOTE (see
Setup menu item 214 REMOTE
INTERFACE: 9PIN
Setup menu 01 PREROLL: 5s
Setup menu item 214 REMOTE
INTERFACE: 9PIN
Function menu page P1 VIDEO >V
INPUT: HD SDI
Setup menu 05 SYNC SEL: ON
Function menu pages P2 and P3 AUDIO Setup menu 06 SYNC VTR:
>A1 to A8 INPUT: SDI RECORDER
Function menu page P5 TC >TCG: INT Setup menu 09 EDIT DLY: –7
Function menu page P5 TC >PRST/
RGN: PRESET
Setup menu 10 R ST DLY:AUTO
Function menu page P5 TC >RUN
MODE: FREE RUN
Setup menu 11 P ST DLY:AUTO
40
Connections and Settings
HDW-M2000 (recorder)
setting
Settings on this unit
Using the editing functions of the
recorder (controlling through
REMOTE(9P) connector)
REMOTE 1 (9P) button:
Unlit
Remote control switch:
REMOTE (see page 18)
Setup menu item 214
The following figure shows a cut editing system
comprising this unit as a player, and an HDW-M2000/
M2000P unit as a recorder. In this example, video and
audio signals are connected by HDSDI, and control signals
are transferred via the REMOTE(9P) connector.
REMOTE INTERFACE: 9PIN
For details of HDW-M2000/M2000P settings, refer to the
HDW-M2000/M2000P Operation Manual.
HD video monitor
Connections for pool coverage
To HDSDI input connector
The following figure shows an example of connections for
pool coverage, with the PDW-700 Professional Disc
Camcorder connected.
1
HDSDI
OUTPUT2
PDW-F1600 or PDW-HD1500
(this unit, player)
PDW-F1600 or PDW-
(SUPER)
PDW-700
HD1500 (this unit)
=
POWER
AC IN
DC IN 12V
REMOTE
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
AUDIO MONITOR
1
2
2
R
L
REF.VIDEO
INPUT
Reference
DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT
HDSDI OUTPUT
video signal
IN
1/2
3/4
1
2
(SUPER)
1
COMPOSITE OUTPUT
(SUPER)
REF.VIDEO INPUT
IN
1
2
OUT
SDSDI OUTPUT
1
2
(SUPER)
1/2
3/4
REF.VIDEO
INPUT
TIME CODE
MAINTENANCE
S400
VIDEO CONTROL
REMOTE(9P)
IN
OUT
To SDI OUT 1 connector
To SD/HDSDI INPUT
connector
1
HDSDI
REMOTE(9P)
75Ω coaxial cable (not supplied)
OUTPUT1
PDW-700 (camcorder)
setting
Settings on this unit
HDW-M2000
(recorder)
REF VIDEO
INPUT
HDSDI
INPUT
1
HDSDI REMOTE I/F on
page CAM CONFIG 1 of
the MAINTENANCE menu:
other than OFF
Remote control switch:
REMOTE (see page 18)
75Ω
Setup menu item 214
REMOTE INTERFACE: SDI
2
HDSDI
OUTPUT 3
(SUPER)
REMOTE 1-OUT(9P)
To HDSDI
input
1
connector
HD video monitor
1: 75Ω coaxial cable (not supplied)
2: 9-pin remote control cable (not supplied)
41
Connections and Settings
Synchronization Reference Signals
The synchronization reference signal generator of this unit
synchronizes to a reference signal input to the REF.
VIDEO INPUT connector or to a video input signal.
External synchronization is as follows, depending on the
setting of OUT REF on page P6 REF of the function menu,
and on the type of the selected input signal. Video output
signals are always synchronized to the internal
synchronization signal.
b)
Input to SD/HDSDI
INPUT connector
Input to REF. VIDEO
INPUT connector
Setting of OUT REF on page P6 REF
REF
a)
INPUT
Yes
Yes
Synchronize to the signal input to Synchronize to the signal input to
the REF. VIDEO INPUT connector the SD/HDSDI INPUT connector
Yes
No
No
No
Yes
No
Synchronize to the signal input to the SD/HDSDI INPUT connector
Synchronize to the signal input to the REF. VIDEO INPUT connector
No external synchronization is made
a) Same as when V INPUT on page P1 VIDEO of the function menu is set to
“SG”.
b) FAM and FTP connections always synchronize to the internal
synchronization reference signal, regardless of the setting of OUT REF.
Synchronization reference signals when
you are recording, playing, or editing 720P
signals
When you are recording, playing, or editing 720P signals,
set OUT REF on page P6 REF of the function menu item
to “REF”, and synchronize the internal reference signal
generator of this unit to a reference signal input to the REF.
VIDEO INPUT connector. The following reference
signals may be used.
720/59.94P system: 1080/59.94i tri-level sync signal, 525
black burst signal
720/50P system: 1080/50i tri-level sync signal, 625 black
burst signal
When you connect this unit directly to the video I/O
connectors of the PDW-F1600/HD1500/F800/700, you
can record and dub 720P signals even if you set OUT REF
on page P6 REF of the function menu item to “INPUT”.
42
Synchronization Reference Signals
Setting System
Frequency
Setting Timecode
There are the following four ways of recording timecode:
Internal Preset mode: This records the output of the
internal timecode generator, set beforehand to an
initial value. The following run modes can be
selected.
This unit can record and play back video at the system
frequencies of 59.94i, 50i, 29.97P, 25P, and 23.98P
(1080) or 59.94P and 50P (720).
1)
• Free Run: Timecode advances continually.
• Rec Run: Timecode advances only during
recording.
1)
When the PDBK-F1500 option is installed.
HD1500
Selecting the system frequency
Internal Regen mode: This records the output of the
internal timecode generator, initialized to timecode
following continuously upon the timecode of the last
frame of the last clip on the disc.
External Regen mode: This records the output of the
internal timecode generator, synchronized to an
external timecode generator. As the external input, the
timecode input to any of the following connectors can
be selected.
1
Set setup menu item 013 SYSTEM FREQUENCY
SELECT MENU to “on” and press the PUSH
SET(S.SEL) knob.
The system frequency selection screen appears.
RETURN
SYSTEM FREQUENCY
SELECT
• TIME CODE IN connector: LTC
• SD/HDSDI INPUT connector: VITC and LTC
-
1080/59.94i
•
(i.LINK) S400 connector: TC
+
If the System Frequency
setting is changed,
External Preset mode: This directly records the input of
an external timecode generator. As the external input,
the timecode input to any of the TIME CODE IN
connector can be selected.
SAVE
Turn power off and on
again.
EXIT
SETUP
To record timecode after setting an initial
value (Internal Preset)
2
Turn the PUSH SET(S.SEL) knob to select the system
frequency to be used.
Proceed as follows with the function menu. For setting the
timecode, set TCG on page P5 TC of the function menu to
INT and PRST/RGN to PRESET.
RETURN
SYSTEM FREQUENCY
SELECT
-
1080/50i
+
Push F5(SAVE) Key!!
SAVE
EXIT
SETUP
3
4
Press the PUSH SET(S.SEL) knob or the SAVE
function button (F5).
The message “Turn off/on POWER!!” appears.
Time data display area
Function menu
After pressing the on/standby button to power off the
unit, power it on again.
Function buttons
Setting an initial timecode value
1
Press the CNTR SEL function button on the HOME
page of the function menu, and select TC.
43
Setting System Frequency / Setting Timecode
2
Press the TCG SET function button (F5).
Select UB by pressing the CNTR SEL function button (F4)
in step 1 of “Setting an initial timecode value” and carry
out steps 2 to 5. Settings are made in hexadecimal (0-9,
A-F).
The first digit of the time data display starts flashing.
You can record ID codes in user bits.
To record timecode that follows
sequentially upon the last recorded
timecode (Internal Regen)
You can record timecode so that it is continuous from one
clip to the next on the disc.
Set TCG on page P5 TC of the function menu to INT, and
PRST/RGN to TC or VITC. When this setting is in force,
the unit reads the timecode of the last frame of the last
recorded clip on the disc before starting to record, and
internally generates timecode that follows upon the
recorded timecode.
The frame count mode (for system frequency 59.94i/
59.94P/29.97P only) is set to the same mode as the last
recorded timecode on the disc (drop-frame or non-drop-
frame).
3
4
Press the T or t function button (F1 or F2) to select
a digit to be set.
The selected digit starts flashing.
Use the PUSH SET(S.SEL) knob or – or + function
button (F3 or F4) to set the value for the selected digit.
To set the next-most significant digit (10s place)
Turn the PUSH SET(S.SEL) knob while holding down
the SHIFT button.
To record with the internal timecode
generator synchronized to external
timecode (External Regen)
Use this method to synchronize the timecode generators of
a number of recorders, to record the playback timecode of
external VTRs, or to record while maintaining
synchronization between the source video and timecode.
Use either of the following procedures according to the
type of external timecode.
Repeat steps 3 and 4 to set all digits that should be set.
To set to 00:00:00:00
Press the RESET/RETURN button.
5
Press the SET function button (F5) .
If RUN MODE on page P5 TC is set to FREE RUN,
the timecode starts running.
Synchronizing with timecode input to the TIME
CODE IN connector
To cancel a setting
1
Connect the timecode output of an external device to
the TIME CODE IN connector, and input a reference
video signal to the REF. VIDEO INPUT connector.
Press the EXIT function button (F6). Any new settings to
that point are canceled, and the setting operation is
terminated.
Setting the timecode to the current time
2
Make the following settings on page P5 TC of the
function menu.
1
2
Set RUN MODE on page P5 TC to FREE RUN and
DF/NDF to DF (in 59.94i/59.94P/29.97P mode only).
• Set TCG to “EXT”.
• Set PRST/RGN to “TC”.
Perform steps 1 to 4 of “Setting an initial timecode
value” to set the timecode to a time slightly ahead of
the current time.
Synchronizing with embedded LTC input to the
SD/HDSDI INPUT connector
1
Input an HDSDI signal containing embedded LTC to
the SD/HDSDI INPUT connector, and a reference
video signal to the REF. VIDEO INPUT connector.
3
Press the SET function button (F5) at the instant when
the current time matches the displayed timecode.
Setting user bits
You can record up to 8 hexadecimal digits of information
(date, time, event number, etc.) on the timecode track.
2
Make the following settings on page P5 TC of the
function menu.
• Set TCG to “SDI”.
44
Setting Timecode
• Set PRST/RGN to “TC”.
Superimposed Text
Information
Executing either of these procedures starts the internal
timecode generator running in synchronization with the
external timecode generator.
Once the internal timecode generator is synchronized with
the external timecode generator, the internal timecode
generator continues to run even if the external timecode
generator connection is removed.
The timecode advance mode is set automatically to Free
Run. The frame count mode (for system frequency 59.94i/
59.94P/29.97P only) is set to the same mode as the external
timecode signal (drop-frame or non-drop-frame).
The video signal output from the COMPOSITE OUTPUT
2 (SUPER) connector, SDSDI OUTPUT 2 (SUPER)
connector, or the HDSDI OUTPUT 2 (SUPER) connector
contains superimposed text information, including
timecode, menu settings, and alarm messages.
Adjusting the text display
You can adjust the position, size and type of the
superimposed text using setup menu items 002, 003, 005,
009, 011, and 012.
To check the synchronization to the external
signal
Press the STOP button to stop this unit, then press the REC
button.
Check that the timecode value shown in the time data
display coincides with the external timecode value.
Information displayed
To record external timecode directly
(External Preset)
When you use this method, the internal timecode generator
advances without being affected by the external timecode.
1 Type of time data
2 Timecode reader drop frame mark
(for 59.94i/59.94P/29.97P mode only)
To directly record timecode input to the TIME
CODE IN connector
Input the timecode output of an external device to the
TIME CODE IN connector, and make the following
settings on page P5 TC of the function menu.
• Set TCG to “EXT”.
3 Timecode generator drop
frame mark (for 59.94i/
59.94P/29.97P mode only)
• Set PRST/RGN to “PRESET”.
Time data
4 VITC field mark
T C R
0 0
:
0 4
.
4 7
.
0 7 *
P L A Y
L O C K
6 Playback condition
mark/Disc
exchange cache
mark
5 Operation mode
Note
The display shown above corresponds to the factory
default settings of the unit. You can change the type of
information to be displayed in the lower line of the display
by changing the setting of setup menu item 005 DISPLAY
INFORMATION SELECT.
45
Superimposed Text Information
a Type of time data
Display
Block A
Operation mode
Display
CNT
TCR
UBR
TCR.
UBR.
TCG
UBG
IN
Meaning
Block B
a)
Counter data
C.STANDBY OFF
Standby off mode
Stop mode
TC reader timecode
STOP
TC reader user bits data
VITC reader timecode
VITC reader user bits data
TC generator timecode
TC generator user bits data
In point time data
a)
C.STOP
Stop mode
NEXT xxx
Cuing up to the first frame of the
next clip.
PREV xxx
Cuing up to the first frame of the
current clip.
F.FWD
F.REV
PLAY
Fast forward search
Fast reverse search
OUT
DUR
Out point time data
Playback mode (servo unlocked)
Playback mode (servo locked)
Record mode (servo unlocked)
Duration between In point and Out point
PLAY
REC
LOCK
Note
a)
C.REC
If the time data or user bits data cannot be read correctly,
they will be displayed with an asterisk. For example,
“T*R”, “U*R”, “T*R.” or “U*R.”.
Record mode (servo unlocked)
REC
LOCK
LOCK
Record mode (servo locked)
a)
C.REC
Record mode (servo locked)
JOG
JOG
JOG
STILL
FWD
REV
A still picture in jog mode
Jog mode in forward direction
Jog mode in reverse direction
A still picture in shuttle mode
Shuttle mode
b Timecode reader drop-frame mark (for 59.94i/
59.94P/29.97P mode only)
“.”: Indicates drop-frame mode.
“:”: Indicates non-drop-frame mode.
SHUTTLE STILL
SHUTTLE (Speed)
c Timecode generator drop-frame mark (for 59.94i/
59.94P/29.97P mode only)
“.”: Indicates drop-frame mode (factory default setting).
VAR
VAR
STILL
A still picture in variable mode
Variable speed mode
(Speed)
“:”: Indicates non-drop-frame mode.
TOP 0001/xxxx
END xxxx/xxxx
PREROLL
Cuing up to the first frame of the
first clip.
d VITC field mark
Cuing up to the last frame of the
last clip.
“ ” (blank): Fields 1 and 3 (for 59.94i/59.94P/29.97P/
23.98P mode) or fields 1, 3, 5 and 7 (for 50i/50P/25P
mode)
Cuing up during thumbnail search
“*”: Fields 2 and 4 (for 59.94i/59.94P/29.97P/23.98P
mode) or fields 2, 4, 6 and 8 (for 50i/50P/25P mode)
a) Display when the unit is in Clip Continuous Rec mode.
f Playback condition mark/Disc exchange cache
mark
e Operation mode
One of three channel condition marks is displayed when
the ACCESS indicator is lit during any mode except
recording. The indication “C” appears here when the disc
exchange cache function is operating.
The field is divided into two blocks as shown below.
• Block A displays the operation mode.
• Block B displays the servo lock status or playback speed.
Display Name
Description
Green
condition
There is no problem with the
playback condition. This unit and
the disc can be used just as they
are. This corresponds to the
“green” channel condition
indicator of a VTR.
A
B
Display
Operation mode
Yellow
condition
The playback condition has
deteriorated to some degree.
There are no read errors, but you
should take the action described
in the next section. This
corresponds to the “yellow”
channel condition indicator of a
VTR.
Block A
Block B
DISC OUT
LOADING
Disc is not loaded.
Disc is being loaded.
Disc is being unloaded.
Standby off mode
UNLOADING
STANDBY OFF
46
Superimposed Text Information
To prevent playback conditions from
deteriorating
Pay attention to the following points when handling discs.
• Do not open disc cartridges and touch discs directly with
your hands.
• Do not store for long periods in locations which are
dusty or exposed to air circulated by fans.
• Do not store for long periods under high temperatures or
in locations exposed to direct sunlight.
Display Name
Description
Red condition The playback condition has
deteriorated. There are no read
a)
errors, but you should take the
action described in the next
section. This corresponds to the
“red” channel condition indicator
of a VTR.
C
Disc
exchange
cache
This appears during cache
recording.
If playback conditions have deteriorated
If a yellow or red playback condition mark appears, check
the following points.
For details, see page 56.
a) Read errors will occur if the playback condition continues to deteriorate.
If a read error occurs, a “Disc Error!” alarm appears in the time data
display, the picture freezes, and audio is muted.
Whether the disc displays the same playback condition
on other XDCAM devices: If so, the surface of the
disc may be dirty or scratched, or the performance of
the recording layers on the disc may have worsened
due to age. Do not use discs with these symptoms.
Whether every disc inserted into an XDCAM device
displays the same playback conditions: If so, the
performance of the laser diodes may have
To display playback condition marks, set setup menu item
012 CONDITION DISPLAY ON VIDEO MONITOR to
“ena”, and set setup menu item 005 DISPLAY
INFORMATION SELECT to “T&sta”.
For details about operation, see “Basic menu operations”
deteriorated. Check the total optical output time.
Playback condition displays
You can be alerted in advance to deteriorating playback
conditions and to error correction rates which are
approaching their limits.
Deteriorating playback may be due to the following
causes.
• Scratches and dust on the disc surface
This includes fingerprints, dust from the air, tar from
cigarette smoke, and so on.
Scratches and soiling which occur before recording are
not a problem because they are registered in advance as
defects, and recording avoids them. However, scratches
and soiling which occur after recording can lead to
deteriorating playback conditions.
• Aging of disc recording layers
Over several decades, the recording layers of optical
discs can age and cause deteriorating playback
conditions.
You can use this function to check archival discs and
other discs which have been stored for extended periods,
so that you can take action before the deterioration
progresses further.
• Deteriorating laser diodes performance
The performance of the laser diodes used in optical
heads can worsen with age, leading to deteriorating
playback conditions.
this setting.
Refer to the Maintenance Manual for an approximate
guide to when it is time to replace optical heads.
47
Superimposed Text Information
button again while the page P2 is displayed switches the
page to P8.
Basic Operations of the
Function Menu
To clear the function menu from the screen
Press the DISPLAY button to switch to the video monitor
display.
The function menu provides access to frequently used
settings, such as input video signal selection and timecode
settings.
Menu settings are stored in nonvolatile memory and are
preserved even after the unit is powered off.
To change the setting of a function menu
item
Use the function buttons.
To select the value of the setting item
Press the button to the left of each setting item to change
the value of the item. Keep pressing the button until the
value you want appears.
Function menu operations
The function menu appears on the color LCD of this unit.
The following figure shows the buttons (numbered 1 to 6
beginning at the top) used in function menu operations.
To set the value of the setting item
• Press the button to the left of each setting item so that the
setting value flashes to enable adjustment of the value
and then turn the PUSH SET(S.SEL) knob to increase or
decrease the value.
• Turning the PUSH SET(S.SEL) knob while holding
down the SHIFT button increases the increment of
adjustment.
Function buttons (1 to 6)
Function menu
• Pressing the button to the left of each setting item while
the setting value is flashing causes the value to stop
flashing and completes the adjustment.
Function menu settings
PUSH SET(S.SEL) knob
DISPLAY button
The following tables list the setting items on each page and
describe their setting values. Underlined values are the
factory defaults.
PAGE/HOME button
To display the function menu
HOME page
The function menu is made up of the HOME page and
1)
1)
pages P1 to P7, (P8) , (HOME2) .
Item
Setting
If the function menu is not already visible, press the
PAGE/HOME button to display it. (The most recently
accessed function menu page appears.)
1) If a menu item is assigned using maintenance menu item M38: F-KEY
CONFIG
F1: CHAR SEL
Turns the display of character
information on the color LCD and on an
external monitor on and off.
ON: Character information on
OFF: Character information off
LCD: Character information on for the
color LCD only
To display a different page
Each press of the PAGE/HOME button displays the next
function menu page in the order: HOME tP1 t P2 t
F2: PB/EE
Selects the type of video and audio
signals to output during fast forward, fast
reverse, stop, and standby.
PB: Playback signal
1)
1)
P3 t P4 t P5 t P6 t P7 t (P8) t (HOME2)
t HOME…
1) If a menu item is assigned using maintenance menu item M38: F-KEY
CONFIG
EE: E-E signal
F3: REC INH
Specifies whether to inhibit recording to
the disc.
OFF: Do not inhibit recording.
ON: Inhibit recording to the disc.
• Turning the PUSH SET(S.SEL) knob while holding
down the PAGE/HOME button changes the page
forward or backward.
• Pressing F1 to F6 buttons while holding down the
PAGE/HOME button switches the page directly to pages
P1 to P6. Pressing the F1 button again while the page P1
is displayed switches the page to P7. Pressing the F2
48
Basic Operations of the Function Menu
Item
Setting
Item
Setting
F4: CNTR SEL
Selects the type of time data to display in
the time data display area.
TC: Timecode
COUNTER: Elapsed recording or
playback time
F5: HUE/CHRM Sets the hue (chroma phase).
PHS
PRESET: Set the hue (chroma phase) to
a preset value, regardless of manual
setting.
Manual setting: While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the hue
(chroma phase) over the range
30°.
UB: User bits
F5: TCG SET
• When CNTR SEL is set to “TC” ,
displays a screen where you can set
the initial value of the timecode
generated by the internal timecode
F6: SETUP/
BLACK
Sets the HD/SD output black setup level
or black level.
PRESET: Set the level to the preset
value, regardless of the manual
setting.
Manual setting: While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to set the black
setup level (in 59.94i/59.94P/
29.97P/23.98P mode) over the
range 30 IRE or the black level (in
50i/50P/25P mode) over the range
210 mV.
a)
• When CNTR SEL is set to “UB” ,
displays a screen where you can set
a)
F6:
(Unassigned function button)
a) This is displayed only when TCG on page P5 TC of the function menu is
set to “INT”, and PRST/RGN is set to “PRESET”.
P1 VIDEO page
Item
Setting
P2 AUDIO page
F1: V INPUT
Selects the video input signal.
HDSDI: HDSDI signal
SDSDI: SDSDI signal
Item
Setting
i.LINK: i.LINK signal (when the PDBK-
201 option board is installed)
SG: Test signal from internal signal
generator (Normally this item is not
displayed. It appears when you hold
the button down for 3 seconds.)
F1: A1 INPUT
Selects the audio input signal to assign
to audio channel 1.
SDI: Audio signal embedded into SDI
signal
ANALOG1: Analog 1 audio signal
AES/EBU1: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 1/2 connectors
SG: Test signal from internal signal
generator (Normally this item is not
displayed. It appears when you hold
the button down for 3 seconds. The
test signal is assigned to audio
channels 1 to 8 simultaneously.)
Press one of the function buttons
corresponding to A1 INPUT to A8
INPUT again to stop output of the
test signal.
F2: VID. PROC
Selects the method used to control the
internal video signal processor and make
related settings.
LOCAL: Use the function menu to
change settings.
MENU: Use the setup menu to change
settings.
F3: VIDEO
Sets the output level for HD/SD video
signals (range –∞ to +3 dB).
PRESET: Set the video signal output
level to a preset value, regardless of
manual setting.
i.LINK: i.LINK signal (when the PDBK-
201 option board is installed)
Manual setting: While the setting value
F2: A2 INPUT
Selects the audio input signal to assign
to audio channel 2.
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the video
signal output level.
SDI: Audio signal embedded into SDI
signal
F4: CHROMA
Sets the output level for HD/SD chroma
signals (range –∞ to +3 dB).
PRESET: Set the chroma signal output
level to a preset value, regardless of
manual setting.
ANALOG2: Analog 2 audio signal
AES/EBU2: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 1/2 connectors
F3: MONITR L
F4: MONITR R
Selects the channel to monitor as the left
monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
Manual setting: While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the
chroma SETUP signal output level.
Selects the channel to monitor as the
right monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
49
Basic Operations of the Function Menu
Item
Setting
Item
Setting
F5: SPEAKER
Enables or disables output from this
unit’s speaker.
F6: A8 INPUT
Selects the audio input signal to assign
to audio channel 8.
OFF: Do not output
ON: Output
SDI: Audio signal embedded into SDI
signal
ANALOG2: Analog 2 audio signal
AES/EBU4: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
F6: LEVEL MT
Specifies the position at which to
superimpose audio level meters in the
video monitor screen (in full-screen
display mode).
OFF: Do not superimpose.
P4 AUDIO page
LEFT: Superimpose the audio level
meters of 2 channels on the left side.
RIGHT: Superimpose the audio level
meters of 2 channels on the right
side.
Item
Setting
a)
F1: A5 VOL
Sets the volume of audio channel 5.
The volume can be adjusted within the
range from –200 to +200 (–∞ to +12 dB)
by turning the PUSH SET(S.SEL) knob.
LEFT(4): Superimpose the audio level
meters of 4 channels on the left side.
RIGHT(4): Superimpose the audio level
meters of 4 channels on the right
side.
LEFT(8): Superimpose the audio level
meters of 8 channels on the left side.
RIGHT(8): Superimpose the audio level
meters of 8 channels on the right
side.
a)
F2: A6 VOL
F3: A7 VOL
F4: A8 VOL
Sets the volume of audio channel 6.
The volume can be adjusted within the
range from –200 to +200 (–∞ to +12 dB)
by turning the PUSH SET(S.SEL) knob.
a)
Sets the volume of audio channel 7.
The volume can be adjusted within the
range from –200 to +200 (–∞ to +12 dB)
by turning the PUSH SET(S.SEL) knob.
P3 AUDIO page
a)
Sets the volume of audio channel 8.
The volume can be adjusted within the
range from –200 to +200 (–∞ to +12 dB)
by turning the PUSH SET(S.SEL) knob.
Item
Setting
F1: A3 INPUT
Selects the audio input signal to assign
to audio channel 3.
Specifies whether to perform audio
mixing according to the settings of setup
menu item 819 AUDIO INPUT
ARRANGE.
OFF: Do not perform audio mixing.
ON: Perform audio mixing.
F1600
F5: MIX/SWAP
SDI: Audio signal embedded into SDI
signal
ANALOG1: Analog 1 audio signal
AES/EBU3: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
F2: A4 INPUT
F3: A5 INPUT
F4: A6 INPUT
F5: A7 INPUT
Selects the audio input signal to assign
to audio channel 4.
(Unassigned function button)
HD1500
F5:
SDI: Audio signal embedded into SDI
signal
F6: AU METER
Selects the display mode of the audio
level meters.
FULL: Display the range from –60 dB to
0 dB.
FINE: Display a magnified section with
0.25 dB step marks.
ANALOG2: Analog 2 audio signal
AES/EBU4: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
Selects the audio input signal to assign
to audio channel 5.
SDI: Audio signal embedded into SDI
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
signal
ANALOG1: Analog 1 audio signal
AES/EBU1: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 1/2 connectors
-
-
Set the VARIABLE switch of the front panel to “REC” or “PB”.
Set setup menu item 131 AUDIO VOLUME to “EACH”.
Selects the audio input signal to assign
to audio channel 6.
SDI: Audio signal embedded into SDI
signal
ANALOG2: Analog 2 audio signal
AES/EBU2: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 1/2 connectors
Selects the audio input signal to assign
to audio channel 7.
SDI: Audio signal embedded into SDI
signal
ANALOG1: Analog 1 audio signal
AES/EBU3: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
50
Basic Operations of the Function Menu
P5 TC page
P6 REF page
Item
Setting
Item
Setting
F1: TCG
Selects the timecode signal to which the
internal timecode generator
synchronizes.
INT: Follow the initial value set from the
control panel or remotely from the
device connected to the
F1: OUT REF
Selects the reference signal for the
output signals of this unit.
REF: Use the signal input to the
REF.VIDEO INPUT connector as the
output reference signal.
INPUT: Use the input video signal as the
output reference signal.
REMOTE(9P) connector, or
synchronize to timecode played
back from the disc.
F2:
(Unassigned function button)
(Unassigned function button)
(Unassigned function button)
EXT: Synchronize to external timecode
input to the TIME CODE IN
connector.
F3:
F4:
SDI: Synchronize to timecode
embedded into HDSDI signal input
to SD/HDSDI INPUT connector.
F5: SYNC
Sets the sync phase of HD output
signals. While the setting value is
flashing, turn the PUSH SET(S.SEL)
knob to adjust the sync phase of output
signals with respect to the input
reference signal, over the range 15 µs.
(The display shows –128 to +127.)
Note
If you select “EXT” or “SDI” while i.LINK
TS signals are being input, synchronizes
to the timecode data in the TS signals.
F6: FINE
Makes fine adjustment to the sync phase
of HD output signals. While the setting
value is flashing, turn the PUSH
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified
from the control panel or remotely
from the device connected to the
REMOTE(9P) connector. This is
valid when “INT” is selected with the
F1: TCG item on this page. The
operation is the same as “TC” when
anything else is selected.
SET(S.SEL) knob to adjust the sync
phase of output signals with respect to
the input reference signal, over the range
200 ns. (The display shows 0 to 1023.)
P7 OTHER page
Item
Setting
F1: CONV IMP
Selects whether to display convert status
on the display during convert operations.
OFF: Do not display.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
ON: Display.
VITC: Generate timecode synchronized
to VITC read by the internal
timecode reader.
F2: ERR LOG
F3: CLIP FLG
Displays an error log screen.
Sets a clip flag for the clip being
recorded or played back using the
function button.
If a clip flag is already set for the clip,
“Marked” is displayed in the function
menu item corresponding to one of the
F1 to F3 buttons depending on the type
of flag that has been set.
F3: RUN MODE Selects the timecode run mode.
FREE RUN: Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN: Timecode advances only
during recording. When you select
this item, also set F1: TCG on this
page to “INT” and set F2: PRST/
RGN to “PRESET”.
A clip flag can also be set or deleted
using the GUI screen. See page 82 for
details.
F4: DF/NDF
F5: PDPSET
Selects the drop-frame mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF: Drop-frame mode
Sub-Item
F1: OK
F2: NG
F3: KEEP
F4:
Set an OK flag.
Set an NG flag.
Set a KEEP flag.
–
NDF: Non-drop-frame mode
When the system frequency is set to
1080/59.94i, 1080/29.97P, or 720/
59.94P, presets the timecode of the A
frame of the pulldown sequence.
24F TC: Reference timecode for A frame
30F TC: Timecode after pulldown
conversion from 24-frame timecode
F5: DELETE Delete the clip flag.
F6: EXIT
Exit the clip flag sub-
menu.
F6: TCR
Selects the type of timecode to display in
the time data display area.
TC: Display TC.
VITC: Display VITC.
51
Basic Operations of the Function Menu
Item
Setting
Handling Discs
F4: PC RMT
Enables or disables a FAM connection.
The connection can be cut off while it is
maintained or remade while it is
disabled.
ENABLE: Enable a connection.
Discs used for recording and
playback
DISABLE: Disable a connection.
Notes
• PC REMOTE under maintenance
menu item M33: FILE I/F CONFIG
must be set to “F-KEY SELECT” in
order to use this function (see
• “DISABLE” is always selected when
the unit is powered off and then on
again, regardless of the previous
setting.
This unit can record and play back the following
Professional Disc formats.
• PFD23A (capacity 23.3 GB)
• PFD50DLA (capacity 50.0 GB)
1)
1) Professional Disc is a trademark of Sony Corporation.
Notes
F5:
F6:
(Unassigned function button)
(Unassigned function button)
• It is not possible to use the following discs for recording
or playback:
- Blu-ray Disc
- Professional Disc for Data
• PFD50DLA discs can be used only by XDCAM devices
with the DL mark (see the following illustration). They
cannot be used by XDCAM devices without this mark.
DL mark
Notes on handling
Handling
The Professional Disc is housed in a cartridge, and is
designed to allow handling free of risk from dust or
fingerprints. However, if the cartridge is subjected to a
severe shock, for example by dropping it, this can result in
damage or scratching of the disc. If the disc is scratched, it
may be impossible to record video/audio, or to play back
the content recorded on the disc. The discs should be
handled and stored carefully.
• Do not touch the surface of the disc itself within the
cartridge.
• Deliberately opening the shutter may cause damage.
• Do not disassemble the cartridge.
• The supplied adhesive labels are recommended for
indexing discs. Apply the label in the correct position.
Storage
• Do not store discs where they may be subjected to direct
sunlight, or in other places where the temperature or
humidity is high.
• Do not leave cartridges where dust may get inside.
• Store cartridges in their cases.
Care of the discs
• Remove dust and dirt on the outside of a cartridge using
a soft dry cloth.
52
Handling Discs
• If condensation forms, allow ample time to dry before
use.
MODE KEY ENABLE DURING RECORDING to
“stop”.
Write-protecting discs
Formatting a disc
To protect the content recorded on the disc from accidental
erasure, move the Write Inhibit tab on the lower surface of
the disc in the direction of the arrow, as shown in the
following figure.
Unused discs are formatted automatically when they are
loaded into this unit.
To format a recorded disc, use the GUI screen.
Lower surface of the disc
Write Inhibit tab
E
V
A
S
Slide in the direction of the arrow
Write Inhibit tab settings
SAVE
SAVE
Recording disabled
Recording enabled
You can also write protect individual clips. For details, see
Loading and unloading a disc
When the on/standby button and indicator are lit green,
you can load and unload a disc as shown in the following
figure.
On/standby button and indicator
To unload
Press the EJECT button.
To load
Insert a disc face up.
The disc is drawn in.
When the EJECT button is pressed during recording,
recording stops and the disc is ejected. If you do not want
to eject the disc and stop recording when the EJECT button
is pressed during recording, set setup menu item 145
53
Handling Discs
Recording and Playback
4
Chapter
Frame frequency groups
The system frequencies supported by this unit are divided
into frame frequency groups, as shown in the following
table.
Recording
This section describes video and audio recording on the
unit.
Frame frequency group
System frequency
59.94 Hz
59.94P
59.94i
29.97P
50P
Chapter 3 for more information.
50 Hz
See page 121 “Menus” in Chapter 7 for more information
about setup menu operations.
50i
25P
23.98 Hz
23.98P
Mixed recording of clips in different
formats on the same disc
You can record clips with different recording formats, for
example HD422 and HD420SP clips, by putting this unit
into mixed format recording mode.
As long as the frame frequency group is the same, clips in
different recording formats can be recorded or written to
the same disc.
In this manual, this is referred to as “mixed format
recording mode”.
To enable mixed format recording mode
Set maintenance menu item M390: MIXED REC to
1)
If you want to disable mixing of clips with different
recording formats, leave this item set to “DSABL”.
However, regardless of the mixed format recording mode
setting, it is always possible to mix clips in the following
format groups.
1) The recording format is regarded as different whenever the system
frequency, video resolution, video codec/bit rate, or number of audio
channels or number of bits does not match.
Notes
• HD420 HQ, SP, and LP
• 1080/59.94i and 1080/29.97P
• 1080/50i and 1080/25P
• Regardless of frame frequency group matching, it is not
possible to mix clips with different video resolutions
(number of system lines) in the same clip list.
• When the unit is in a mode that calls for playback across
clips that were recorded in different recording formats,
video and audio playback may stop at the point where
the format changes from one format into another, and
then start again.
Preparations for recording
Make the following settings and adjustments before
starting to record.
• If a transition point between two clips with different
recording formats exists in the preroll segment, that
segment cannot be edited.
Video input signal selection: Select with V INPUT on
page P1 VIDEO of the function menu.
Audio input signal selection: Select with A1 INPUT and
A2 INPUT on page P2 AUDIO, from A3 INPUT to
A8 INPUT on page P3 AUDIO of the function menu.
54
Recording
Recording starts.
Selection of time data to display: Select with CNTR SEL
on HOME page of the function menu.
Selection of audio channels to monitor: Select with
MONITR R and MONITR L on page P2 AUDIO of
the function menu.
3
To stop recording, press the STOP button.
If the disc becomes full
Recording stops and the message “ALARM DISC END.”
appears on the monitor.
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
Notes
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set setup menu item 214
REMOTE INTERFACE (“RM-” and the connector
used appear on the system information of the display)
• The shortest clip that can be recorded is 2 seconds long.
Even if recording start and stop operations are performed
within 2 seconds, a 2-second clip is recorded.
• The maximum number of clips that can be recorded is
300. If the loaded disc already contains 300 clips,
recording operation is not possible. (The message
“MAX # Clips” appears in the time data display area.)
• This unit can record video input signals that are not
synchronized to a reference signal. However, in that
case, video breakup and audio noise may occur in E-E
playback.
SD up convert function
You can input SD signals to the SD/HDSDI INPUT
connector and record them as HD signals.
User data recording
You can record user data (files other than XDCAM AV
files) on Professional Discs as PC data via the i.LINK or
FTP interface.
This allows Professional Discs to be used as data recording
media, with a data storage capacity of 46.4 GB (when dual-
layer PFD50DLA discs are used).
• During recording, do not turn off the POWER switch on
the rear panel or disconnect the power cord. This could
cause the clip being recorded to be lost.
To adjust the audio recording levels
When carrying out audio recording at a reference
level
Carrying out recording
Set the VARIABLE switch to PRESET.
The audio signals will be recorded at a preset reference
level.
One recording segment (from the start to the end of
recording) is called a “clip”.
You can change the reference level and the input levels
with maintenance menu item M37: AUDIO CONFIG.
maintenance menu settings.
1
Manually adjusting the audio recording levels
Set the VARIABLE switch to REC and adjust the CH-1/
ALL CH and CH-2 to CH-4 knobs so that the audio level
indications on the audio level meters do not exceed 0 dB
for a maximum volume. Carry out the adjustment in E-E
mode.
EJECT
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PRE-
PAGE
NET
LOCAL
ON
SET
PB
OFF
REMOTE
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
See setup menu item 108 AUTO EE SELECT (page 129)
for more information about the signal output settings in E-
E mode.
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
2 3
To set shot marks
1
2
Insert a disc.
A Shot Mark1 essence mark or Shot Mark2 essence mark
is set if you hold down the V/MARK1 or v/MARK2
button and press the PUSH SET(S.SEL) knob during
recording. If you connect a Windows USB keyboard to the
Hold down the REC button, and press the PLAY
button.
55
Recording
MAINTENANCE connector, you can record shot marks
from Shot Mark0 up to Shot Mark9 by pressing the 0 to 9
keys on the numeric keypad.
If the unit is set up to display superimposed text
appears every time you set an essence mark.
When Shot Mark0 to Shot Mark 9 is set, you can search for
the shot marks by displaying thumbnails of the frames at
When recording on the current disc ends, the disc is
ejected. Until the next disc is inserted, the unit records
to its internal cache memory. Then, after the new disc
is inserted, it copies the data from the cache to the disc
and resumes normal recording.
Disc exchange cache indications and their
meanings
Indication
Meaning
You can also use shot mark positions as edit points during
Right side of icon Recording to the cache
flashes once per
second
You can also set shot marks during playback. See page 64
for the procedure.
Left side of icon
flashes twice per
second
Remaining memory capacity: Low
To set a clip flag
Whole icon flashes Remaining memory capacity:
You can set one of the three types of flag (OK, NG or
KEEP) for the clip while it is being recorded by viewing its
four times per
second
None (disc full)
You can also set a clip flag during playback. See page 64
for details.
“C” indications in superimposed text information
and their meanings
Indication
Meaning
You can also set a clip flag on the GUI screen. See page 82
for details.
“C” flashes once
per second
Recording to the cache
“C” flashes twice
per second
Remaining memory capacity: Low
Continuing recording while
exchanging discs (disc exchange
cache function)
An alarm message Remaining memory capacity:
appears instead of None (disc full)
“C”.
About 30 seconds (this duration may differ depending on
the state of a disc) of video and audio data can be recorded
to the unit’s internal memory cache during a disc
To stop disc exchange cache recording
Do any of the following during cache recording.
• Press the STOP button.
exchange, and then written back to the newly loaded disc.
• Set setup menu item 150 REC MODE to “normal”.
1
2
Check that setup menu item 150 REC MODE is set to
“disc exchange cache”.
Notes
• If the disc becomes full while setup menu item 150 REC
MODE is set to “disc exchange cache”, the disc is
ejected and the unit continues to record to its internal
memory (for about 30 seconds depending on the state of
a disc).
• Recording and playback operations by all buttons and
dials other than the STOP button are disabled during
cache recording.
• If the amount of cache data exceeds the capacity of the
unit’s internal memory during a disc exchange, an alarm
message appears and the data in cache memory is
overwritten. The internal memory always contains the
latest cache data, so the clip data will be continuous after
the next disc is inserted and recording to the disc
resumes.
If the disc exchange cache indication is lit in the time
display, setup menu item 150 REC MODE is set to
“disc exchange cache”.
If none of the indications of step 1 appear, set setup
menu item 150 REC MODE to “disc exchange cache”
The setting of 150 REC MODE can be changed even
during recording.
However, if you change the setting from “clip
continuous rec”, the setting change is enabled after the
end of Clip Continuous Rec mode recording.
3
Exchange the disc.
56
Recording
Exchanging discs
Recording with the HDSDI remote
control function
Even during recording, it is possible to eject discs by
pressing the EJECT button on the front panel. After a disc
is exchanged, the unit resumes operation according to the
embedded REC or STOP command.
This section explains the settings required for recording in
HDSDI remote control mode, and how the unit operates in
this mode.
Note
This unit begins recording operation about one second
after the camcorder.
Note
The unit (camcorder) that controls this unit must also
support HDSDI remote output.
Recording with the Clip Continuous
Rec function
Settings
Set setup menu item 214 REMOTE INTERFACE to
“SDI”, and set the remote control switch on the front panel
to “REMOTE”.
This unit enters HDSDI remote control mode, in which it
is controlled by command packets received via the SD/
HDSDI INPUT connector.
Normally, a clip is generated as an independent file every
time recording starts and stops. The Clip Continuous Rec
function allows you to continue recording to the same clip
until the function is stopped or turned off, regardless of
how many times recording starts and stops. This is
convenient if you want to avoid generating a large number
of short clips, or if you want to record without worrying
about the limit on the number of clips (maximum 300). A
Rec Start essence mark is recorded whenever recording
starts, which makes it easy to find the recording start points
Note
The following limitations apply in HDSDI remote control
mode.
• Commands received via the REMOTE(9P) connector
are ignored.
• Recording and playback operations on the front panel
are disabled, except for the EJECT button.
Note
A new clip may be created the next time you start
recording if it is impossible to continue recording to the
same clip because of signal noise or some other reason.
Monitor display in HDSDI remote control mode
“RM-SDI” appears in the remote interface display area
(see page 26) of the monitor. This display lights if
command packets are embedded into HDSDI signals, and
flashes if they are not. However, the “RM-SDI” continues
to flash until the time the controlling camcorder is powered
on and the time that the REC button is pressed on the
camcorder.
To enable the function
Set setup menu item 150 REC MODE to “clip continuous
rec”.
For details about operation, see “Basic menu operations”
Recording operation
When a recordable disc is inserted, recording (or stop) is
executed according to the REC (or STOP) command
embedded into the HDSDI signals.
Recording stops automatically when the end of the disc is
reached.
To record
Send a “REC” command from a controlling device
connected to either of the following connectors.
• REMOTE(9P) connector
• SD/HDSDI INPUT connector (Put the unit into HDSDI
remote control mode.)
When HDSDI signals are interrupted during
recording
To stop recording
Recording stops if HDSDI signals are interrupted during
recording, for example because the HDSDI cable is
disconnected or the controlling camcorder is powered off.
When HDSDI signal input is restored, the unit resumes
operation according to the embedded REC or STOP
command.
Send a “REC PAUSE” command.
To stop the function
Do one of the following to stop the Clip Continuous Rec
function. (A new clip will be generated the next time you
start recording.)
• Perform a clip operation (lock, delete, or rename a clip)
• Make a network or FAM connection
• Eject the disc
57
Recording
system to perform a full salvage of the disc. As the other
system, use the PDW-F800 or PDW-700.
appear when you insert a disc:
“DISC CANNOT BE RECORDED. FORMAT DISC
OR CONTACT SERVICE TO RUN CLIP SALVAGE
PROGRAM. (XXXX)”
• Change the recording format (change the setting of setup
menu item 031 RECORDING FORMAT)
• Power the unit off
To turn the function off
Set setup menu item 150 REC MODE to “normal”.
This message means that recording on that disc did not
end normally. The “XXXX” in the message is a code for
XDCAM devices that can salvage the disc. Refer to the
following table and use one of the indicated devices to
salvage the disc.
Handling of discs when recording
does not end normally (salvage
functions)
Recording processing does not end normally if, for
example, the POWER switch on the rear panel is turned off
during recording, or if the power cord is disconnected
during recording. Because the file system is not updated,
video and audio data recorded in real time is not
recognized as files and clip contents recorded up to that
point are lost.
However, this unit has salvage functions which can hold
losses to the minimum by reconstructing clips on such
discs. There is a quick salvage function which executes
automatically and a full salvage function which you can
execute as required.
Code (XXXX) Model
0002
PDW-1500/530/510/R1
PDW-F70/F350/F330
0200
PDW-F70/F350/F330 (Version 1.9 or
higher)
PDW-F75/F355/F335
a)
a)
PDW-HD1500/HR1/700
0300
0301
PDW-HD1500/700 (Version 1.5 or higher)
PDW-F1600/F800
a)Does not appear on this unit.
• Even when these functions are used, it is not possible to
recover data from immediately before the interruption of
recording. The amount of data lost is as follows.
Quick salvage: From 2 to 4 seconds of data before the
interruption of recording.
Quick salvage: Clips are reconstructed on the basis of
backup data stored in nonvolatile memory and
markers recorded on the disc. Processing time is about
5 seconds.
Quick salvage executes automatically if the unit is
powered on with a disc still loaded after recording
was interrupted by power off.
Full salvage: From 4 to 6 seconds of data before the
interruption of recording.
(More data may be lost when the unit is subject to
vibrations, and when you switch frequently between
recording and paused.)
• You are prompted to execute a full salvage every time
you insert a disc that has not been salvaged, or power the
unit on with such as disc loaded.
• No recording is possible on discs containing clips that
have not been salvaged, although it is possible to play
back the normally recorded sections. Recording
becomes possible if you perform a quick format, but this
erases all of the original recorded content.
Full salvage: Clips are reconstructed on the basis of
markers recorded on the disc. Nonvolatile memory
cannot be used, so processing takes longer than for a
quick salvage (about 30 seconds, although it depends
on the state of the disc).
You are prompted to execute a full salvage whenever
you insert a disc that was removed manually from a
powered off device after interruption of recording by
power off.
Note that no recorded clip contents are lost when the on/
standby button on the front panel is set to standby during
recording, because the unit does not enter standby mode
until after the end of recording processing.
To restore clips with a full salvage
1
Insert the disc on which recording did not end
normally.
Notes
• Even after recording finishes, do not set the POWER
switch on the rear panel to off until the ACCESS
indicator has gone out.
• These functions salvage as much recorded material as
possible after an unforeseen accident, but 100%
restoration cannot be guaranteed.
The message “Salvage ?” appears on the display.
To cancel the clip salvage
Press the RESET/RETURN button.
Notes
• When recording on the PDW-F1600 or PDW-HD1500
does not end successfully, you can use another XDCAM
• The message “EJECT?” appears when “REC INHI”
is displayed. If the disc is write protected, eject the
58
Recording
disc, set the Write Inhibit tab to enable recording,
and then insert the disc again. If REC INH on
HOME page of the function menu is set to “ON”, set
F1600
Linear Editing
• This operation cannot be cancelled once it begins.
2
Press the PUSH SET(S.SEL) knob.
Overview
Processing begins and the message “Executing.”
appears.
When processing finishes, a message appears to
display the results.
You can perform the following types of editing on
recorded clips.
Type of editing
Editing target
If the message reads “Incomplete!”, the clips that
failed were lost.
Insert editing
Video tracks in a single clip.
Audio tracks in a single clip. (Split editing
is also possible. But the Out point must
be shared with the video tracks.)
Timecode in a single clip.
Assemble editing Final clip.
Notes
• A disc which contains clip lists cannot be used as a disc
for editing. However, it can be used as a playback disc.
• A disc which contains clips in different recording
formats cannot be used as a disc for editing. However, it
can be used as a playback disc if you create a clip list that
contains only clips in one of the recording formats.
• Locked clips cannot be edited.
• Editing across multiple clips is not possible.
• It is not possible to carry out assemble editing other than
on the final clip.
• If there is no space on the disc, in assemble editing it will
not be possible to extend the clip.
• Preread editing is not supported.
• After linear editing, discs in the MPEG HD422 format
cannot be read by the versions 1.2 or earlier of the PDW-
HD1500/700. To play such discs on the PDW-HD1500/
700, upgrade the software to version 1.5 or higher.
• Even after linear editing, the underlying VANC data is
not rewritten. (VANC data cannot be edited.) However,
essence mark data is rewritten (can be edited).
• Linear editing is not possible when the unit is in one of
the following modes. To perform linear editing, exit the
mode.
- Single clip playback mode
- Clip Continuous Rec mode
- Disc Exchange Cache mode
• Normally, linear editing on this unit can target only clips
that have been created on XDCAM devices. It may not
be possible to edit clips that been created by other
software applications and uploaded to this unit as files.
Editable clip recording formats
This unit supports editing of the following recording
formats.
• MPEG HD422 1080 59.94i/29.97P/50i/25P/23.98P
• MPEG HD422 720 59.94P/50P
59
Linear Editing
• MPEG IMX 59.94i/50i
• DVCAM 59.94i/50i
recording format of the editing target clip. The following
table shows the required settings.
Item
Setting
Note
Recording format Check the recording format of the clip
with the display window (see page 24)
Editing of the MPEG HD420 format is not supported.
and select the same format with setup
menu item 031 RECORDING FORMAT.
Editable video and audio signals
This unit supports editing of the following signals on video
and audio tracks.
• Video
Audio/Non-audio
(data)
To perform insert editing of non-audio
(data), set maintenance menu item
M37: AUDIO CONFIG >M372: NON-
AUDIO INPUT to “data”.
- HD-SDI (for HD recording)
- SD-SDI (for SD recording)
• Audio
- SDI
- Analog
Notes
• When you insert non-audio into a clip,
the channels containing the non-
audio are treated as non-audio
across their entire length.
• Use channel pairs (CH1/2, CH3/4,
CH5/6, CH7/8) for non-audio insert
editing. Non-audio editing is not
executed unless a channel pair is
specified.
- AES/EBU
Notes
• Video and audio signals input to the (i.LINK) S400
connector cannot be edited.
• Editing cannot be done with a File Access Mode (FAM)
connection.
operations.
• Recording of upconverted SD is not supported.
menu operations.
Discs that can be used
Settings required for editing
Use the following Professional Discs.
The following table shows the settings required for editing.
Model number Capacity
Data transfer rate
(writing)
Item
Setting
PFD23A
23.3 GB
50.0 GB
2.4 times normal
Audio digital signal With the maintenance menu item M39:
PFD50DLA
processor
OTHER CONFIG >M393: AUDIO DSP,
select “linear edit”.
Note
Video input signal
Select the video input signal with V
INPUT on page P1 VIDEO of the
function menu.
A PFD23 Professional Disc with a 2 times normal data
transfer rate cannot be used for linear editing.
Audio input signal
Input audio level
Select the audio input signal with A1
INPUT and A2 INPUT on page P2
AUDIO, and A3 INPUT to A8 INPUT
on page P3 AUDIO of the function
menu.
Connections
Adjust the input audio level with the
CH-1/ALL CH and CH-2 to CH-4
knobs.
Make connections in the same way as for a cut editing
Edit point transition With setup menu item 317 AUDIO
When making the connections, also refer to the operation
manuals provided with the equipment to be connected.
type
EDIT MODE, select “cut edit” or “cross
fade”.
Audio mix
Time code
See the next section “To set up mixing
of audio input signals”.
Preparations for editing
• With TCG on page P5 TC of the
function menu, select “INT”.
• With PRST/RGN on page P5 TC of
the function menu, select
“PRESET”.
• With RUN MODE on page P5 TC of
the function menu, select “FREE
RUN”.
Recording format settings
Before performing clip editing, you need to set the
recording format of the PDW-F1600 units to match the
60
Linear Editing
menu operations.
In this state, you can turn the selected input channel on
or off.
operations.
To toggle the input channel on (highlighted) or off
Do one of the following.
• Turn the PUSH SET(S.SEL) knob.
• Press the – or + function button (F3 or F4).
operations.
To confirm the setting and return to the input
channel selection screen
Press the PUSH SET(S.SEL) knob.
To set up mixing of audio input signals
By making setup menu settings, you can perform the
following kinds of audio mixing.
• Mixing of audio input signals.
• Changing the channels of audio input signals and
recording to disc.
To exchange input channels
For example, turn input channel 2 on for recording
channel 1, and turn input channel 1 on for recording
channel 2.
• Mixing of audio input signals and audio that has been
recorded to disc (sound on sound).
To mix multiple audio input signals
For each of the recording channels, turn any two input
channels on.
1
Display setup menu item 819 AUDIO INPUT
ARRANGE.
To make sound-on-sound settings
In addition to the input channels, also turn “PB” on.
operations.
4
5
Repeat steps 2 and 3 until you have set up mixing for
all of the required channels.
ITEM-819
Press the SAVE function button (F5).
AUDIO INPUT ARRANGE
The settings are saved, and the unit exits the audio
setup mode.
*CH1: 1 2 3 4 5 6 7 8 PB
CH2: 1 2 3 4 5 6 7 8 PB
CH3: 1 2 3 4 5 6 7 8 PB
CH4: 1 2 3 4 5 6 7 8 PB
CH5: 1 2 3 4 5 6 7 8 PB
CH6: 1 2 3 4 5 6 7 8 PB
CH7: 1 2 3 4 5 6 7 8 PB
CH8: 1 2 3 4 5 6 7 8 PB
6
Set MIX/SWAP on page P4 AUDIO of the function
menu to “ON”.
The setting of setup menu item 819 AUDIO INPUT
ARRANGE is enabled.
Input channels
Recording channels
Editing operations
To return to the setup menu
Press the PUSH SET(S.SEL) knob without turning it.
Notes
• When the In and Out points are not set in the same clip,
insert editing is performed only for the clip containing
the In point.
2
3
Turn the PUSH SET(S.SEL) knob to move the “*” to
the recording channel that you want to set up, and then
press the PUSH SET(S.SEL) knob.
The screen changes to the input channel selection
screen.
Clip 2
Clip 1
To return to the recording channel selection screen
Press the PUSH SET(S.SEL) knob without turning it.
IN point
OUT point
Turn the PUSH SET(S.SEL) knob to move “p” to the
input channel that you want to turn on, and then press
the PUSH SET(S.SEL) knob.
Edit execution segment
61
Linear Editing
• If the OUT point is set within the final clip, in assemble
editing the length of the clip does not change.
Playback
Carrying out clip editing
To carry out clip editing, use an RM-280 or similar editing
controller.
This section describes playback of video and audio on the
unit.
Before starting playback, make the following settings and
adjustments.
Selection of time data to display: Select with CNTR SEL
on HOME page of the function menu.
Selection of audio channels to monitor: Select with
MONITR L and MONITR R on page P2 AUDIO of
the function menu.
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set setup menu item 214
REMOTE INTERFACE (“RM-” and the connector
For details of how to set edit points and carry out editing,
refer to the operation manual for the editing controller.
Note
If an assemble edit command is received while
maintenance menu item M393: AUDIO DSP is set to
“AGC/limiter”, the unit creates a new clip and performs
normal recording.
Essence marks recorded by clip editing
“CUT” is recorded as an essence mark at the IN and OUT
points of video insert editing, and at the IN point of
assemble editing. By selecting “CUT” in the essence mark
selection screen, you can search the result of editing.
Clip playback modes
You can set the clip playback mode to either of the
following.
For details of searching using essence marks, see page 76.
Continuous playback mode: The playback target is all of
the clips on the disc (factory default setting)
Single clip playback mode: The playback target is the
currently selected clip only
To select single clip playback mode
Set setup menu item 154 SINGLE CLIP PLAY MODE to
“on”.
Playback in single clip playback mode
Playback stops when it reaches the start or end of the clip.
The next and preceding clips are not played, even if they
exist on the disc. The available playback types include
normal playback, high-speed playback in the forward or
reverse directions, and jog, shuttle, and variable playback.
When this unit is set to repeat playback mode, the selected
clip only is played repeatedly.
To move to another clip, press the PREV, NEXT, SHIFT
+ PREV, or SHIFT + NEXT button, or perform a
thumbnail search.
Pulldown playback
When this unit’s system frequency is set to 1080/59.94i,
1080/29.97P, or 720/59.94P, clips recorded as 1080/
23.98P are converted by 2-3 pulldown before playback
(pulldown playback).
Timecode in pulldown playback
During pulldown playback, timecode is also converted to
30 frames to match the output video signals.
The upper row of the time data display area displays the
original 24-frame timecode, and the lower row displays the
30-frame timecode.
62
Playback
SD up convert function
TC
VITC
00:59:59:23
By installing the PDBK-S1500 option, you can output HD
while playing discs recorded as SD.
PDT 00:59:59:29
You can superimpose the 30-frame timecode after
pulldown on an external monitor. To do so, set setup menu
item 005 DISPLAY INFORMATION SELECT to “time
data only”.
HD down convert function
You can always output SD while playing discs recorded as
HD.
TCR 00:59:59:23
PDT 00:59:59:29
To specify the frame to use as the
thumbnail image
Disc playback start position
Although this unit uses optical discs, it is designed to offer
the most convenient features of tape playback by VTRs.
One of these is the playback start position, which works in
the same way as tape, as described below.
You can display a list of thumbnails of all clips on a disc,
When the unit is shipped from the factory, it is set up to
display the first frame of each clip as the thumbnail. As
required, you can select another frame to display as the
thumbnail.
For example, if there are several seconds of color bars
recorded at the start of the clip, selecting a frame several
seconds after the end of the recording of color bars can
make it easier to identify the clip.
After playback stop
The unit stops at the position where the STOP button was
pressed.
Press the PLAY button to resume playback at the stop
position.
After recording
The unit stops at the position where recording ended.
To play back a clip, press the PREV button to move to the
start frame of any clip or press the PREV button with the
PLAY button held down to move to any position.
The GUI screen allows you to select thumbnail frames
while viewing the video.
After disc insertion
The unit stops at the position of the disc when it was most
recently ejected.
Press the PLAY button to resume playback at the most
recent position.
The playback position is saved to the disc when the disc is
ejected, which allows playback to start at that position
whenever it is loaded into any XDCAM player.
You can also use setup menu item 143 INDEX PICTURE
POSITION to specify a different default frame. You can
specify the initial frame in any of the first few seconds
after the initial frame. The setting range is 0 seconds to 10
seconds.
Playback operation
Note
This section describes the following types of playback:
Normal playback: Playback at normal speed
Playback in jog mode: Variable-speed playback, with the
speed determined by the speed of turning the jog dial
Playback in shuttle mode: Variable-speed playback, with
the speed determined by the angular position of the
shuttle dial
Playback in variable-speed mode: Variable-speed
playback, with the speed finely determined by the
angular position of the shuttle dial
This function is not available when the Write Inhibit tab of
the disc is set to the recording disabled position, and when
REC INH on HOME page of the function menu is set to
“ON”.
The REC INHI indicator may light when neither of the
above is true if the format of recorded sections on the disc
is not the same as the recording settings of this unit. In this
case, the playback position can be saved to the disc.
1080/720 cross convert function
Normal playback
First insert a disc.
You can output 720 while playing discs recorded as 1080,
and output 1080 while playing discs recorded as 720.
When the system frequency of the loaded disc (59.94i/
59.94P/29.97P, 50i/50P/25P, or 23.98P) matches the
system frequency of the unit, but the system line settings
(1080 or 720) do not match, then an “FC” mark appears
and disc playback is cross converted automatically. E-E
output is not cross converted.
For details of how to insert a disc, see “Loading and
63
Playback
information about how to install it.
EJECT
You can also delete and modify essence marks from the
Thumbnail Menu of the chapter thumbnail screen (see
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
ARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
To set a clip flag
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
You can set one of the three types of flag (OK, NG or
KEEP) for the clip while it is being played back by
viewing its video image and using the function menu (see
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
1 2 3 4
5 6 7
1 PREV button
2 PLAY button
3 NEXT button
4 STOP button
5 Jog dial
6 Shuttle dial
7 V/MARK1 button and v/MARK2 button
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +1 times normal speed.
To carry out playback in jog mode, proceed as follows.
To start playback
EJECT
Press the PLAY button.
Playback starts.
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
When two or more clips are recorded on the disc, they are
played back continuously.
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
Note
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
No audio is output when non-audio signals are played
back.
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
To jump to the next or previous clip, then start
playback
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
1 2,3 1
1
2
Press the SHTL/JOG button or VAR/JOG button,
turning it on.
To stop playback
Press the STOP button.
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
If you play back to the end of the last clip, playback
automatically stops.
If, in this state, you press the PLAY button, the message
“Disc End!” appears on the display.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial” (factory
default setting), you can start jog playback by simply
rotating the jog dial, even when the SHTL/JOG and
VAR/JOG buttons are not lit.
To set shot marks
While playing back a disc, you can set essence marks such
as Shot Mark1 and Shot Mark2 in desired frames.
To set a Shot Mark1 or Shot Mark2, hold down the V/
MARK1 or v/MARK2 button and press the PUSH
SET(S.SEL) knob. If you connect a Windows USB
keyboard to the MAINTENANCE connector, you can
record shot marks from Shot Mark0 up to Shot Mark9 by
pressing the 0 to 9 keys on the numeric keypad.
Use the PDZ-1Proxy Browsing Software on the supplied
XDCAM Application Software CD-ROM to delete and
modify essence marks.
Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is 20 times normal speed.
To carry out playback in shuttle mode, proceed as follows.
64
Playback
1
2
Press the VAR/JOG button, turning it on.
EJECT
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
Playback in variable-speed mode starts.
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
3
To stop playback in variable-speed mode, return the
shuttle dial to the center position, or press the STOP
button.
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
To alternate between normal-speed playback and
variable-speed mode playback
Set the shuttle dial to the position corresponding to the
desired variable playback speed, then switch between
normal-speed playback and variable-speed mode playback
by pressing the PLAY and VAR/JOG buttons alternately.
3
1 2,3
1
2
Press the SHTL/JOG button, turning it on.
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
To perform manual frame sync playback
Playback in shuttle mode starts.
During playback, you can adjust the playback output phase
in units of one frame. To do so, hold down the PLAY
button and turn the PUSH SET(S.SEL) knob in either
direction.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
To speed up the phase: Turn clockwise.
To delay the phase: Turn counterclockwise.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial” (factory
default setting), you can start shuttle playback by
simply rotating the shuttle dial, even when the SHTL/
JOG button is not lit.
Playback operations using
thumbnails
To alternate between normal-speed playback and
shuttle mode playback
Playback operations that you can perform with thumbnails
include searching for clips, displaying clip information,
playing clip lists created with the scene selection function,
and locking and deleting clip. This allows you to check the
actual video as you work.
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SHTL/JOG buttons alternately.
Playback in variable-speed mode
information about thumbnail operations, and “Scene
information about the scene selection function.
In variable-speed mode, you can control the speed of
playback in the range of –2 to +2 times normal speed. (You
can use setup menu item 119 VARIABLE SPEED LIMIT
IN KEY to specify the speed range of variable playback.)
To carry out playback in variable-speed mode, proceed as
follows.
EJECT
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
3
2,3 1
65
Playback
Operations in GUI
Screens
5
Chapter
Overview
You can perform scene searches, play the searched scenes,
and select scenes (edit clip list) in Graphical User Interface
(GUI) screens. The GUI screens are your gateways to discs
and the data saved on discs.
(The GUI screens can display European languages,
Japanese, Korean, Simplified Chinese, and Traditional
Chinese for clip names and titles.)
Switching between GUI screens
The most important GUI screens are:
Clip thumbnail screen: displays thumbnails of clips on
the disc. “Clip” is displayed as the title at the upper
Clip list thumbnail screen: displays thumbnails of sub
clips in a clip list. “Clip List” is displayed as the title
There are also two playback screens:
Clip playback screen: playback screen for normal video
Clip list playback screen: playback screen for clip list
video
You will use the THUMBNAIL button 1 and the SUB
CLIP/DISC MENU button 2 to switch between these
four screens. Each press of these buttons switches between
the screens as shown in the following figure. The
THUMBNAIL and SUB CLIP/DISC MENU indicators
light as follows, according to the type of screen that is
currently displayed.
Note
To switch between these four screens, a disc with recorded
clips must be loaded in the unit.
66
Overview
a)
Clip thumbnail screen
Clip playback screen
Clip:C0006
006/040
TC 00:25:06:14
TC 00:27:51:09
TC 00:23:54:22
1
1
TC 00:23:00:25
TC 00:25:49:23
TC 00:28:06:09
TC 00:23:40:07
TC 00:26:22:10
TC 00:28:22:02
TC 00:24:45:11
TC 00:27:19:04
TC 00:23:34:18
TCR 00 : 23 : 00 . 26
JOG
STILL
001/036
DATE&TIME 30 NOV 2005 13:38 DUR 0:00:10:23
THUMBNAIL
THUMBNAIL
Unlit
Unlit
Lit
1
2
1
2
SUB CLIP
SUB CLIP
Unlit
DISC MENU
DISC MENU
2
2
2
2
a), b)
b)
Clip list playback screen
Clip list thumbnail screen
Clip List:E0001
002/013
TC 00:00:20:13
TC 00:00:53:22
TC 00:01:17:27
1
1
TC 00:00:00:00
TC 00:00:28:08
TC 00:00:59:16
TC 00:00:04:14
TC 00:00:35:15
TC 00:01:06:18
TC 00:00:12:04
TC 00:00:46:08
TC 00:01:13:11
TCR 00 : 00 : 18 . 01
SHUTTLE STILL
F0008 : 003/005
DATE&TIME 28 JUL 2006 19:55
TOTAL DUR 00:01:31:16
THUMBNAIL
THUMBNAIL
Unlit
Lit
Lit
1
2
1
2
SUB CLIP
SUB CLIP
Lit
DISC MENU
DISC MENU
a) Playback screens appear when you switch to video monitor display. Use the DISPLAY button to switch from the basic monitor
b) The clip list playback screen appears when a clip list is loaded into the unit’s memory (see page 90).
The other thumbnail screens are:
To specify that titles, if they exist, should be displayed
with higher priority than names, select one of the following
under Settings >Display Title in the Disc Menu.
On: Title1 "title1": Display in the order title1, title2, clip
or clip list name.
• Expand thumbnail screen
• Chapter thumbnail screen
• Essence mark thumbnail screen
On: Title2 {title2}: Display in the order title2, title1, clip
or clip list name.
Information and controls in
thumbnail screens
To change the display language according to the area of
Settings >Select Font in the Disc Menu.
About the display of clip and clip list
names
You can specify that titles should appear instead of names
in the clip name areas of thumbnail screens. You can also
change the display language.
Area of use
setting
Select Font
setting
Displayable
languages
J (for Japan)
–
English/Japanese
67
Overview
e Recording format
Area of use
setting
Select Font
setting
Displayable
languages
The recording format of the selected clip is displayed as a
combination of the following information.
• Video format logo
UC (for regions European
outside Japan) Alphabet
English/European
languages
• Number of system lines
• Recording quality
• Number of audio channels
Korean
English/Korean
Simplified
Chinese
English/Simplified
Chinese
Traditional
Chinese
English/Traditional
Chinese
f Clip date and time
Displays the date and time when the selected clip was shot
and recorded.
Clip thumbnail screen
g Duration
This screen displays thumbnails of clips on the disc in the
order that they were recorded. You can use this screen to
work with clips – deleting or locking them, selecting their
index pictures, adding them to clip lists, and so on.
Displays the duration (recording time) of the selected clip.
When multiple clips are selected, displays the total
recording time of the selected clips.
A Thumbnail display items
1
2
3
OK
TC 00:26:22:10
4
5
6
a Index picture
Displays an image to stand for the content of the clip. The
index picture is normally the first frame of the clip.
b Index picture changed mark
a Clip name
Displays the name or a title of the selected clip (see
This mark, like the folded-over corner of a page that you
want to remember, appears when the index picture has
been changed to any frame other than the first frame of a
b Selection frame
Indicates that the thumbnail is selected. To select another
selection frames appear when multiple thumbnails are
Note
When you cue up a clip, the unit always cues up the first
frame, even when the index picture has been changed to a
different frame.
c Clip number/total number of clips
Displays the total number of clips on the disc, and the
number of the selected clip.
c S mark
This mark appears when shot marks or other essence
The chapter thumbnail screen can be displayed for clips
d Scrollbar
When not all of the thumbnails can be displayed in the
thumbnail display area, the position of the slider shows the
relative position of the currently displayed clips, and the
length of the slider shows the relative length of currently
displayed clips within all of the clips.
When you have a large number of thumbnails, you can
save time by using the Skip Scroll function to jump
d Clip flag icon
Displays the corresponding icon when a clip flag (OK/NG/
KP (KEEP)) is set in the clip.
e Clip and frame information
Displays the clip or frame information selected with the
Clip Information item in the Thumbnail Menu (see
68
Overview
page 79). The factory default selection is the timecode of
f Total duration
the first frame or the timecode of the thumbnail frame.
Displays the total duration of all sub clips in the clip list.
f Lock icon
Expand thumbnail screen
This screen displays thumbnails of equally sized divisions
of the selected clip.
This icon appears when the clip is locked (protected) (see
page 83). Clips cannot be deleted and their clip
information cannot be changed when this mark is
displayed.
1
2
3
4
Clip list thumbnail screen
This screen displays thumbnails of the clips in the current
clip list. You can use this screen to create and edit clips
lists.
Expand Clip 008/024 x 12
001/012
TC 00:01:36:27
TC 00:01:38:22
TC 00:01:40:16
TC 00:01:35:17
TC 00:01:37:11
TC 00:01:39:06
TC 00:01:38:00
TC 00:01:37:24
TC 00:01:38:19
TC 00:01:36:14
TC 00:01:38:08
TC 00:01:40:02
1
2
3
4
Clip List:E0001
002/013
TC 00:00:20:13
TC 00:00:53:22
CLIP Tene
DUR 0:00:00:13
TC 00:00:00:00
TC 00:00:28:08
TC 00:00:59:16
TC 00:00:04:14
TC 00:00:12:04
TC 00:00:46:08
TC 00:01:13:11
5
6
TC 00:00:35:15
TC 00:01:06:18
a Selection frame
TC 00:01:17:27
DATE&TIME 28 JUL 2006 19:55
TOTAL DUR 00:01:31:16
b Clip number/total clips × number of divisions
Displays the number of the selected clip, the total number
of clips on the disc, and the number of times that the
selected clip has been divided to display the expansion
thumbnails.
5
6
a Clip list name
c Thumbnail number/total thumbnails
Displays the total number of expanded thumbnails and the
number of the selected thumbnail.
b Selection frame
d Scrollbar
c Sub clip number/number of sub clips
Displays the total number of sub clips in the clip list, and
the number of the selected sub clip.
e Clip name
d Scrollbar
Displays the name or a title of the expanded clip (see
f Duration
e Clip list date and time
Displays the time from the selected thumbnail to the next
one.
Displays the date and time when the clip list was created,
or the date and time of its most recent modification. An
asterisk (*) appears after the date and time of creation
when the current clip list has not been saved to the disc.
Chapter thumbnail screen
Chapters are the sections between the shot marks, Rec
Start marks, and other essence marks that have been
recorded in clips. This screen allows you to display
thumbnails of the chapters in the selected clip.
Note
“New File” appears when no clip list has been loaded into
the unit’s memory, and when a clip list has been cleared
from the unit’s memory.
69
Overview
Essence mark thumbnail screen
Note
This screen displays thumbnails of the specified essence
mark, found by searching all clips on the disc.
Shot marks can be set by the user during recording and
playback. They can be deleted and moved.
Essence marks other than shot marks are set automatically.
They cannot be deleted or moved.
1
2
3
4
1
2
3
4
5
Shot Mark1
TC 00:23:02:00
TC 00:26:22:11
TC 00:28:35:00
001/029
TC 00:25:40:24
TC 00:28:06:17
TC 00:29:20:03
Chapter of Clip 001/024
001/003
TC 00:24:45:25
TC 00:27:19:25
TC 00:28:55:02
TC 00:25:07:01
TC 00:27:51:25
TC 00:29:10:05
TC 00:23:00:25
TC 00:23:02:00
TC 00:23:04:00
30 NOV 2006 19:55
"Capping literally years of spe..."
CLIP C0001
DUR 0:00:01:05
5
6
a Essence mark name
6
7
Displays the name of the essence mark (Shot Mark1 here).
If the shot mark name has been defined by the user, it is
enclosed in quotation marks (" ") in the display (see
a Selection frame
b Selection frame
b Clip number/total clips
Displays the total number of clips on the disc and the
number of the clip that contains the displayed chapters.
If the essence mark name is a user-defined name, it is
displayed between quotation marks, for example as
c Essence mark number/total essence marks
Displays the total number of essence marks and the
number of the selected essence mark.
c S1/S2/RS marks
Note
The “S1”, “S2”, and “RS” marks on the thumbnails
indicate frames where Shot Mark1, Shot Mark2, and Rec
Start essence marks are set.
The total number of essence marks is the total number of
essence marks that have been set in all clips on the disc.
d Chapter number/total chapters
Displays the total number of chapters and the number of
the selected chapter.
d Scrollbar
Note
e Clip date and time
Displays the date and time when the clip that contains the
selected thumbnail was recorded or last modified.
The total number of chapters is the total number of
chapters in the specified clip only.
f Clip name
Displays the name or a title of the clip that contains the
e Scrollbar
f Clip name
Displays the name or a title of the clip whose chapter is
Displaying menus
Thumbnail Menu
g Duration
The Thumbnail Menu displays menu items that are valid
for the currently displayed thumbnail screen.
Displays the time from the first frame of the selected
chapter to the first frame of the next chapter.
70
Overview
To display the Thumbnail Menu
Clip thumbnail screen
To display the Thumbnail Menu, press the MENU button
with a thumbnail screen displayed. To return to the original
screen, press the MENU button again, or press the RESET/
RETURN button.
1
2
EJECT
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
1
1 or 2
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
1 MENU button
2 RESET/RETURN button
Thumbnail Menu of the clip thumbnail screen
Shortcut operations
Shortcut button names are displayed next to the menu
Note
Shortcuts displayed within parentheses should be used
with all menus closed.
Thumbnail Menu submenus
• The Thumbnail Search Menu contains the basic
commands for thumbnail searches.
• The Thumbnail View Menu contains the basic
commands for moving to other menus.
Disc Menu
The Disc Menu allows you to do the following.
Item
Operation/Setting
Load Clip List
Save Clip List
Load clip list into this unit’s memory.
Save a clip list on the disc under its current name, overwriting the old
contents.
Save Clip List as…
Save a clip list on the disc under a new name.
Delete a clip list from the disc.
Delete Clip List
Clear Clip List
Clear the current clip list from the unit’s memory.
Load Planning Metadata/Select Drive
Select a media disc or drive and load planning metadata into this
unit’s memory.
Planning Metadata Properties
Clear Planning Metadata
Display the properties of the currently loaded planning metadata.
Clear the currently loaded planning metadata from the unit’s memory.
71
Overview
Item
Operation/Setting
Lock or Delete All Clips
Sub-Item
Lock All Clips
Unlock All Clips
Delete All Clips
Lock all clips.
Unlock all clips.
Delete all clips.
Disc Properties
Format Disc
Display the properties of the currently loaded disc. Or edit the user
disc ID, title 1, and title 2.
Format (initialize) the currently loaded disc.
Download Clip via Direct FTP
Settings Sub-Item
Used to send clip to and from remote devices and remote computers.
SET Key on Thumbnail
Selects the behavior of the unit when the PUSH SET(S.SEL) knob is
pressed with one thumbnail selected.
Cue up & Still: Cue up the selected thumbnail.
Cue up & Play: Cue up and play the selected thumbnail.
Sort Clip List by…
Selects a method to sort the clip list.
Name (A-Z): Sort in ascending alphabetic order.
Date (Newest First): Sort by date and time of creation, newest clip
list first.
Sort Planning Metadata
by...
Selects a method to sort the planning metadata.
Name (A-Z): Sort in ascending alphabetic order.
Date (Newest First): Sort by date and time of creation, newest
planning metadata first.
Display Title
Selects whether to display clip and clip list titles.
On: Title1 "title1": Display the title in the following order of priority:
Title1, Title2, Clip name or Clip list name.
On: Title2 {title2}: Display the title in the following order of priority:
Title2, Title1, Clip name or Clip list name.
Off: Do not display the title. Always display the clip name or clip list
name.
Planning Clip Name in Clip Selects whether to display in the video monitor screen the title
Info. Area
contained in a planning metadata file that is loaded into this unit.
Off: Do not display title.
ASCII Clip Name: Display title in ASCII format.
Clip Name: Display title in UTF-8 format.
Disable “Format Disc”
Select Font
Selects whether to disable the Format Disc command.
Disable: Disable the command.
Enable: Enable the command.
Selects the language (font) used to display clip names, clip list
names, and title2 clip titles.
Select USB Keyboard
Language
Selects a language of the USB keyboard used on the software
keyboard.
Select Mouse Pointer
Speed
Selects the speed of the USB mouse pointer used on the software
keyboard from the following values.
5 Fast/4/3 Middle/2/1 Slow
To display the Disc Menu
To display the Disc Menu, press the SUB CLIP/DISC
MENU button with the SHIFT button held down in one of
the following screens.
• Clip thumbnail screen
• Clip list thumbnail screen
• Clip playback screen
• Clip list playback screen
To return to the original screen, press the RESET/
RETURN button.
72
Overview
GUI screen operations
3
EJECT
1
2
3
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
EJECT
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
CH-2
RESET
CHAPTER
EXPAND
MARK1
PUSH SET(S.SEL)
ACCESS
RETURN
IN
OUT
CH-1
CH-3
CH-4
VARIABLE KEY INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
MENU
PRE-
ARK2
SET
OFF
SHTL/JOG
PB
HOME
ALL CH
VAR/JOG
CH-2
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
RESET
CHAPTER
EXPAND
RETURN
SUB CLIP
DISC MENU
VARIABLE KEY INHI
TOP
F
REV
F
FWD
END
STANDBY REC INHI
REC
PAGE
NET
LOCAL
REMOTE
ON
PRE-
SET
OFF
PB
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
1
2
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
1 SHIFT button
2 SUB CLIP/DISC MENU button
3 RESET/RETURN button
6
5
4
1 PUSH SET(S.SEL) knob
2 B/IN, b/OUT button
Clip list thumbnail screen
Clip List:E0001
3 V/MARK1, v/MARK2 button
4 Jog and shuttle dials
5 RESET/RETURN button
6 SHIFT button
002/013
TC 00:00:00:00
TC 00:00:28:08
TC 00:00:59:16
TC 00:00:04:14
TC 00:00:35:15
TC 00:01:06:18
TC 00:00:12:04
TC 00:00:46:08
TC 00:01:13:11
TC 00:00:20:13
TC 00:00:53:22
To select items
Do one of the following to select thumbnails, menu items,
timecode digits, and other items.
• Turn the PUSH SET(S.SEL) knob.
• Turn the jog or shuttle dial.
• Press the V/MARK1, v/MARK2, B/IN or b/OUT
button.
• Press the PREV or NEXT button.
TC 00:01:17:27
DATE&TIME 28 JUL 2006 19:55
TOTAL DUR 00:01:31:16
1+2
3
• With the SHIFT button held down, press the PREV or
NEXT button (to move to the first or last item).
• With the SHIFT button held down, press the V/MARK1
or v/MARK2 button (to move to the previous or next
page).
Disc Menu
Load Clip List
Save Clip List
Save Clip List as...
Delete Clip List
Clear Clip List
Load Planning Metadata/Select Drive
Planning Metadata Properties
Clear Planning Metadata
To select multiple thumbnails
Do one of the following
• Turn the PUSH SET(S.SEL) knob with the SHIFT
button held down.
Lock or Delete All Clips
• With the SHIFT button held down, press the B/IN or b/
OUT button.
To return to the previous screen
Press the RESET/RETURN button.
To move from a menu level to the next
lower or higher menu level
For a menu item displayed together with b or B, you can
move to the next lower or higher menu level by pressing
the B/IN or b/OUT button.
73
Overview
To scroll hidden parts of the string into
view
When a b or B mark is displayed for an item, you can
press the B/IN or b/OUT button to scroll the display by
one character for each press.
Thumbnail Operations
You can use thumbnail screens to display clip information
and to find, protect, and delete clips. The thumbnails
provide visual confirmation of these and other operations.
The V/MARK1 and v/MARK2 buttons scroll the
beginning and end of the string into view.
To increment and decrement numbers
Do one of the following.
Selecting thumbnails
• Press the V/MARK1 or v/MARK2 button.
• Turn the PUSH SET(S.SEL) knob.
• Turn the jog dial.
currently selected thumbnail.
To move the thumbnail selection frame
Turn the PUSH SET(S.SEL) knob.
To confirm selections
Press the PUSH SET(S.SEL) knob.
To skip quickly through thumbnails (Skip
Scroll function)
When you have a large number of thumbnails, like in
expand thumbnail screen, you can use the Skip Scroll
function to skip through them quickly.
thumbnail screens.
1
2
In the screens like clip thumbnail screen or expand
thumbnail screen, display the Thumbnail Menu.
Select Skip Scroll, and then press the PUSH
SET(S.SEL) knob.
A small popup window appears on the scrollbar to
indicate the position of the currently selected
thumbnail within the set of all thumbnails.
Expand
007/235
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
Skip Scroll
007/235
DUR 0:00:00:01
CLIP "Seashore"
DUR 0:00:00:01
3
Turn the PUSH SET(S.SEL) knob.
1
The current position moves by an amount equal to /
of the total number of thumbnails.
10
When you reach a point that is close to the thumbnail
you want, turn the jog dial to move the selection frame
in units of 1 thumbnail.
74
Thumbnail Operations
4
Press the PUSH SET(S.SEL) knob at the new position.
first frame in each block. This is a quick and efficient way
to review the selected clip and search for target scenes.
You can specify 12, 144, or 1728 divisions.
The thumbnail at the position indicated in the small
popup window appears in a thumbnail screen like the
1)
following .
Expand
007/235
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
DUR 0:00:00:01
Note
The maximum number of blocks may be other than 1728
when the recorded duration of the clip is short. In this case,
the frame interval of expanded thumbnails is fixed at 1
frame. This allows you to view expanded thumbnails at
equal intervals.
CLIP "Seashore"
DUR 0:00:00:01
1)Expand thumbnail screen
operations.
To select multiple thumbnails
Move the selection frame to the first thumbnail that you
want to select. Then, with the SHIFT button held down,
turn the PUSH SET(S.SEL) knob.
To cancel the multiple selection, move the selection frame
without the SHIFT button held down.
1
2
In the clip thumbnail screen, select the thumbnail of
the clip that contains the scene you want to find.
Press the EXPAND button.
The selected clip is divided into 12 blocks, and a list
appears in the expand thumbnail screen (see page 69)
with the first frame of each block displayed as a
thumbnail.
Clip:"Navigating sibling relati..."
018/036
TC 00:30:25:11
TC 00:24:24:29
TC 00:25:49:07
TC 00:29:19:23
TC 00:30:40:13
TC 00:24:34:27
TC 00:29:38:25
TC 01:01:28:25
TC 00:24:46:22
TC 00:29:50:04
TC 00:09:43:14
TC 00:25:42:08
3
4
Select the thumbnail that you want to expand further.
Repeat steps 2 and 3 up to 2 times, as required.
Note
DATE&TIME 30 NOV 2005 14:14 DUR 0:23:22:26
Thumbnails cannot be further expanded when they already
have the minimum duration (1 frame).
Searching with thumbnails
To return to the previous expansion level
Press the EXPAND button with the SHIFT button held
down.
By using the thumbnails that appear in the various
thumbnail screens, you can easily cue up and play clips
and sub clips.
To display the expand thumbnail screen of the
previous or next clip
With the expand thumbnail screen still active, press the
PREV button or the NEXT button.
Using thumbnails to find clips
The clip thumbnail screen displays thumbnails of all clips
recorded on the disc. You can use this screen to cue up the
Using the chapter function to find scenes
Chapters are the sections between the shot marks, Rec
Start marks, and other essence marks.
Rec Start essence marks are set automatically at the start of
recording, but shot marks can be set at any scene during
recording or playback.
information.
Using the expand function to find scenes
The expand function allows you to divide a selected clip
into equally sized blocks, and to display thumbnails of the
The chapter function allows you to display thumbnails of
the chapters in a clip.
75
Thumbnail Operations
2
3
Display the Thumbnail Menu.
operations.
Select Move Essence Mark.
The Move Essence Mark screen is displayed.
1
In the clip thumbnail screen, select the thumbnail of a
clip with chapters set.
The “S” mark appears on the thumbnails of clips with
chapters set.
2
Press the CHAPTER button.
with thumbnails of the frames where chapters are set.
The “S1”, “S2”, and “RS” marks on the thumbnails
indicate frames where Shot Mark1, Shot Mark2, and
Rec Start essence marks are set.
You can perform playback and searches in this screen.
4
5
Use the PLAY button or jog dial to display the frame
you want.
To delete the shot mark at a chapter position
You can delete the shot mark (Shot Mark0 to 9) at the
chapter position in the chapter thumbnail screen. (Rec
Start cannot be deleted.).
Select OK, and then press the PUSH SET(S.SEL)
knob.
To display the chapter thumbnail screen of the
previous or next clip with chapters
With the chapter thumbnail screen still active, press the
PREV button or the NEXT button.
The unit searches in the reverse or forward direction for the
next clip with chapters, beginning with the previous or
next clip.
1
In the chapter thumbnail screen, select the thumbnail
for the frame whose shot mark you want to delete.
2
3
Display the Thumbnail Menu.
Select Delete Essence Mark.
A message appears asking if you are sure that you want
to delete the shot mark.
Using essence marks to find scenes
operations.
1
In the clip playback screen or the clip thumbnail
screen, press the THUMBNAIL button with the
SHIFT button held down.
The Select Essence Mark screen appears.
The names of essence marks that are not recorded on
the disc are displayed in gray.
4
Select OK to delete the mark, or Cancel to cancel the
deletion, and then press the PUSH SET(S.SEL) knob.
Select Essence Mark
Shot Mark1
Shot Mark2
Rec Start
Cut
To adjust the position of shot marks at chapter
positions
You can use the chapter thumbnail screen to adjust the
position of shot marks (Shot Mark0 to 9) at chapter
positions. (The positions of Rec Start essence marks
cannot be adjusted.)
Others
1
In the chapter thumbnail screen, select the thumbnail
of the shot mark whose position you want to adjust.
76
Thumbnail Operations
If planning metadata with user-defined essence
mark has been loaded
You can select user-defined essence marks (see
To search for a thumbnail position and cue
it up
operations.
1
Select the thumbnail that you want to cue up.
Clip:C0010
010/041
OK
TC 00:23:00:25
TC 00:25:49:23
TC 00:28:06:09
TC 00:23:40:07
TC 00:26:22:10
TC 00:28:22:02
TC 00:24:45:11
TC 00:27:19:04
TC 00:23:34:18
TC 00:25:06:14
TC 00:27:51:09
TC 00:23:54:22
2
Select the essence mark that you want, and then press
the PUSH SET(S.SEL) knob.
DATE&TIME 30 NOV 2005 13:40 DUR 0:00:04:14
The essence mark thumbnail screen displays a list of
frames where the selected essence mark is set.
2
Press the PUSH SET(S.SEL) knob.
To switch directly to the Rec Start essence mark
thumbnail screen
Before starting, set setup menu item 153 FIND MODE to
“clip & rec start mark”.
By pressing the DISPLAY button in the clip thumbnail
screen, you can switch directly to the Rec Start essence
mark thumbnail screen. As long as the setting of setup
menu item 153 does not change, the DISPLAY button
switches between the clip thumbnail screen and the Rec
Start essence mark thumbnail screen.
To play clips with the PUSH SET(S.SEL) knob
In the Disc Menu, set Settings >SET Key on Thumbnail to
“Cue up & Play”. Playback begins from the selected frame
when you press the PUSH SET(S.SEL) knob, in the same
way as when you press the PLAY button.
To search for a thumbnail position and
play from there
This setting allows you to use the DISPLAY button as a
shortcut to Rec Start essence mark thumbnail screen,
which is convenient for checking start points in clip
recorded with the Clip Continuous Rec function.
Also, when the Rec Start essence mark thumbnail screen is
displayed, each press of the THUMBNAIL button
switches between that screen and the clip playback screen
(Resume function). In the clip playback screen, the PREV
and NEXT buttons jump to the previous or next recording
start points.
operations.
1
2
Select the thumbnail that you want to play.
Press the PUSH SET(S.SEL) button.
Note
The DISPLAY button does not switch to the Rec Start
essence mark thumbnail screen from the expand thumbnail
screen or the chapter thumbnail screen.
TCR 00 : 26 : 22 : 10
PLAY
C0010: 010/041
Playing the scene you have found
After finding a clip with one of the methods explained in
the previous section, “Searching with thumbnails” (see
page 75), you can cue up and play the clip that you have
found.
Selecting clips by type (Filter Clips
function)
You can select clips of a certain type from among all of the
clips on a disc (Filter Clips function). For example, you
can do the following.
77
Thumbnail Operations
• Select clips in a certain video format from a disc that
contains clips in different video formats.
• Select clips that have been set “NG” as a clip flag, and
delete all of those clips in one operation.
• Select only clips that have been recorded on the basis of
a specified planning metadata entry, and transfer those
clips to an external device using the Direct FTP function.
To filter clips
operations.
7
If you want to filter the clips again with a different
filtering condition (to narrow down the filtering
results), repeat steps 2 to 6. (The command name
selected in step 4 changes to Filter Clips(Narrowing).)
1
2
Display the clip thumbnail screen.
If you want to select clips by video format, select the
thumbnails of clips in that format.
To play selected clips continuously
Register all of the filtered clips in an automatically
generated clip list, and play the clip list.
3
4
Display the Thumbnail menu.
Select “Filter Clips”, and then press the PUSH
SET(S.SEL) knob.
1
2
Display the Thumbnail Menu in the filter thumbnail
screen.
The Filter Clips screen appears.
Select “Copy to Clip List”, and then press the PUSH
SET(S.SEL) knob.
A clip list thumbnail screen appears, showing filtered
clips that have been registered in the clip list.
5
Select the clip filtering condition.
Item name
Filtering condition
Clip Flag: OK
Clip Flag: NG
Clip flag set in the clip (OK/NG/
KP(KEEP)/none)
3
Press the PLAY button.
Clip Flag:
KP(KEEP)
The screen changes to the clip playback screen, and
playback starts.
Clip Flag: none
Current Planning
Metadata
Clips that have been recorded
according to the instructions in the
currently loaded planning
metadata
Operations on filtering results
You can use the Thumbnail Menu in the filter thumbnail
screen to perform the following operations.
AV Format of
Selected Clip
Video format of the selected clips
Item name
Function
6
Press the PUSH SET(S.SEL) knob.
Clip Information
Select the information to be
displayed at the bottom of the
thumbnails.
A filter thumbnail screen appears, showing only clips
that meet the specified condition.
The filtering condition appears at the lower left of the
screen.
Lock or Delete All Filtered Lock all of the filtered clips.
Clips >Lock All Filtered
Clips
78
Thumbnail Operations
Sequence Number: Thumbnail sequence number
Return to Upper Menu: Returns to the Thumbnail
Menu
Item name
Function
Lock or Delete All Filtered Unlock all of the filtered clips.
Clips >Unlock All Filtered
Clips
The selected information will appear at the bottom of
the thumbnails when you display a thumbnail screen.
Lock or Delete All Filtered Delete all of the filtered clips.
Clips >Delete All Filtered
Clips
Filter Clips(Narrowing)
Narrow down the filtering
results.
Changing clip index pictures
Copy to Clip List
Copy all of the filtered clips to a
new clip list.
The clip thumbnail screen displays thumbnails as index
pictures for clips. Normally the index picture is the first
frame in a clip, but you can set any frame in the clip as the
index picture.
Upload Clips via Direct
FTP
Transfer all of the filtered clips
to an external device via a
network.
To display clip filtering conditions as Title2 titles
For clip lists created with the Copy to Clip List command,
you can display the clip filtering conditions as Title2 titles.
When Settings >Display Title in the Disc Menu is set to
"On: Title2 {title2}", the clip filtering conditions are
displayed automatically in screens such as the Load Clip
List screen.
Note
You can only change index pictures from the clip
thumbnail screen. The thumbnails shown in the clip list
thumbnail screen, the expand thumbnail screen, and the
chapter thumbnail screen cannot be changed.
To select a clip index picture while viewing the
video
Selecting the information displayed
on thumbnails
operations.
You can select the information to be displayed at the
bottom of the thumbnails in thumbnail screens.
1
In the clip thumbnail screen, select the thumbnail of
the clip whose index picture you want to change.
operations.
2
3
Display the Thumbnail Menu.
Select Select Index Picture.
Select Index screen appears.
1
2
Display the Thumbnail Menu in the clip thumbnail
screen.
Select Clip Information.
018/036
Select Index:"Navigating sibling relati..."
A window appears in which you can select the
information to display.
Thumbnail Menu
Clip Information
Return to Upper Menu
Date
OK
TCR 01:09:16:13
Cancel
Time Code
Duration
Sequence Number
You can play and search with this screen.
4
5
Select a frame with the PLAY button or the jog dial.
Select OK, and then press the PUSH SET(S.SEL)
knob.
3
Select the items that you want to display.
Date: Date and time of creation, or date and time of the
more recent modification
Time Code: Timecode of first frame
Duration: Playback time
79
Thumbnail Operations
To select index pictures by using the expand and
chapter functions
frame as the index picture of the clip.
The following example explains how to do so from the
expand thumbnail screen.
operations.
1
In the expand thumbnail screen, select the thumbnail
to set as the index picture.
Clip No.: Clip number/total number of clips
Name: Clip name
1)
2
3
Display the Thumbnail Menu.
Select Set Index Picture.
Title1: Title1
Title2: Title 2
AV Format: Recording format
TC: Timecode of first frame
DUR: Recording time
Created: Date and time of creation
Modified: Date and time of most recent modification
Rec Device: Name of device that created clip (product
number)
1)
A message appears asking you to confirm that you
want to set the current frame as the index picture.
Set Index Picture
OK
TC 00:01:38:00
1)When the unit’s area of use (UC/J MODEL SELECT) (see page 33)
is set to “UC”, titles can be displayed in European languages.
Cancel
To scroll hidden parts of the string into view
When a b or B mark is displayed for an item, you can
press the B/IN or b/OUT button to scroll the display
by one character for each press.
The V/MARK1 and v/MARK2 buttons scroll the
beginning and end of the string into view.
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
To display the properties of the previous or the
next clip
Press the PREV button or the NEXT button.
After pressing the RESET/RETURN button to return
to the clip thumbnail screen, check to make sure that
the newly selected frame is displayed as the index
picture.
To return to the clip thumbnail screen
Press the PUSH SET(S.SEL) knob.
To edit clip information
You can edit the name, title1, and title 2 of a clip by
Checking clip properties
1)
using a software keyboard.
You can check clip properties such as the title, timecode,
duration, date and time of creation, and date and time of
the more recent modification.
1) The “NAMING FORM” sub-item on setup menu item 036 must be set to
operations.
Notes
• The only characters that can be entered are the
alphanumeric characters and characters in the fonts
supported by this version of the unit’s firmware.
Japanese kanji cannot be entered.
• Names and titles must be within the specified character
length limits.
1
2
Display the Thumbnail Menu in the clip thumbnail
screen.
Select Clip Properties.
The Clip Properties screen appears.
• Some symbols cannot be used in clip names. The keys
for those symbols are disabled when you are editing a
clip name.
80
Thumbnail Operations
operations.
To enter text using a USB keyboard or USB
mouse
You can connect a Windows USB keyboard or a Windows
1)
1
In the Clip Properties screen, turn the PUSH
SET(S.SEL) knob to select the item you want to edit
page 29), and use them together with the software
keyboard to enter text.
1)
(Name, Title1 , or Title2).
Connect a Japanese keyboard if you have set the area of
use to “J” (for Japan).
1)Only ASCII characters can be used for Title1.
2)
Connect a keyboard that corresponds to the font selected
with Disc Menu item Settings >Select Font if you have set
the area of use to “UC” (for regions outside Japan).
2
Press PUSH SET(S.SEL) knob.
An input screen appears for the selected item.
(If the area of use setting is “UC” (for regions outside
Japan), a keyboard appears that corresponds to the font
selected with Disc Menu item Settings >Select Font.)
A Japanese keyboard appears if the area of use setting
is “J” (for Japan).)
1) Some USB keyboards or USB mice may not be recognized. In this case,
the message “Unknown USB” appears.
2) Only ASCII characters can be entered from a Japanese keyboard.
To change the display language (font) for clip names,
clip list names, and title2 clip titles: Select one of
the following languages (fonts) with the Disc menu
item Settings >Select Font.
• European Alphabet: The keyboard language can be
selected with the Disc Menu item Settings >USB
Keyboard Language (see following section).
• Korean: The Korean keyboard is selected
automatically. You can enter Hangul characters if
you have connected a Korean USB keyboard.
• Simplified Chinese: The keyboard layout is identical
to that of the English [United States] keyboard. Only
ASCII characters can be entered.
3
Edit the string in the edit box.
• Traditional Chinese: The keyboard layout is
identical to that of the English [United States]
keyboard. Only ASCII characters can be entered.
To change the keyboard language: Select the desired
language from the following values using Settings
>Select USB Keyboard Language in the Disc Menu.
• English [United Kingdom]
To enter characters
Use the V/MARK1, v/MARK2, B/IN or b/OUT
buttons or turn the PUSH SET(S.SEL) knob to select a
key, and then press the PUSH SET(S.SEL) knob.
Functions of special keys
• English [United States]
• French [France]
• German [Germany]
• Italian [Italy]
Key
Function
B, b
Move the cursor one character forward or
back.
,
Move the cursor to Home or End position.
Deletes the character in front of the cursor.
• Polish (Programmers) [Poland]
• Russian [Russia]
• Spanish [Spain]
Back
Space
CapsLock Turns the Shift key on permanently (until
pressed again), and enables input of capital
letters and symbols.
the characters that can be input in each language.
F Shift
Enables input of capital letters and symbols.
Turns off after entry of one character.
Note
Enter
Confirms the edit and enables the OK and
Cancel buttons.
The keyboard language cannot be changed in the following
cases.
• When the area of use is set to “J” (for Japan).
• When the area of use is set to “UC” (for regions outside
Japan), and the Disc Menu item Settings >Select Font is
set to “Korean”, “Simplified Chinese”, or “Traditional
Chinese”.
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
You return to the Clip Properties screen, and the
results of the editing are reflected in the clip
information.
81
Thumbnail Operations
The keyboard icon on the software keyboard is highlighted
when a USB keyboard has been recognized and enabled
for use with this unit, and the mouse icon is highlighted
and a mouse pointer appears when a USB mouse has been
enabled.
To change the speed of the mouse pointer: Select the
desired speed using Settings >Select Mouse Pointer
Speed in the Disc Menu. Select the speed that works
best with the connected mouse.
To exit the software keyboard from a USB
keyboard
1
2
With the cursor in an edit box, press the Enter key to
move the focus to OK.
Do one of the following.
To confirm the edit and then exit the software
keyboard: While OK is selected, press the Enter
key.
To discard the edit and then exit the software
keyboard: On the USB keyboard, press the r key
or the Tab key to move to Cancel, and then press
the Enter key.
To continue editing: Press any key except the Enter
key, the Esc key, and the Tab key.
Notes
• Use the proper keyboard for the area of use. Some
characters may not be entered correctly if you use a
keyboard designed for use in another area.
• It is not possible to enter Japanese, even on a Japanese
keyboard.
Setting clip flags
USB keyboard special functions keys
In addition to the special function keys of the software
keyboard, you can use the following special function keys
on a USB keyboard.
You can set three types of clip flags (OK/NG/KP (KEEP))
during recording or playback. Setting these flags in each
clip that you record makes it easy for editors and other
colleagues to find and select the clips that they need.
Key
Function
V, v
When the cursor is in an edit box:
Move the cursor to the start or
end.
operations.
When “OK” or “Cancel” has the
focus: Moves the focus between
“OK” and “Cancel”.
1
In the clip thumbnail screen, select the thumbnail of
the clip where you want to set a flag.
Delete
Deletes the character after the cursor.
2
3
Display the Thumbnail Menu.
Shift + B, Shift + b Selects the string before or after the
cursor.
Select Set Clip Flag.
Ctrl + C, X, V, A, Z Ctrl + C: Copies the selected string.
Ctrl + X: Cuts the selected string.
Ctrl + V: Pastes a copied or cut string.
Ctrl + A: Selects the entire string.
Ctrl + Z: Undoes the immediately
preceding operation.
The clip flag setting screen appears.
Thumbnail Menu
Set Clip Flag
Enter
When the cursor is in an edit box:
Moves the focus to OK.
When OK or Cancel has the focus:
Exits the software keyboard.
Return to Upper Menu
OK
NG
KP (KEEP)
none
Esc
Tab
When the cursor is in an edit box,
moves the focus to Cancel.
Moves the focus between OK and
Cancel.
4
Select the clip flag that you want to set (OK/NG/KP
(KEEP)).
USB mouse functions
You can use the mouse to move the cursor on the software
keyboard. You can also left click on a key to enter the
character for that key.
have clip flags set.
82
Thumbnail Operations
To clear clip flags
Carry out steps 1 to 3, selecting a clip that has a flag set,
and then select “none” in step 4.
3
Select OK to lock all clips or Cancel to cancel it, and
then press the PUSH SET(S.SEL) knob.
To unlock a specific clip
You can also use CLIP FLG on page P7 OTHER of the
operations.
Locking (write-protecting) clips
1
In the clip thumbnail screen, select the thumbnail of
the clip that you want to unlock.
In a clip thumbnail screen, you can lock the selected clips
so that they cannot be deleted or altered.
Locking prevents the following operations on clips.
• Deletion
2
3
Display the Thumbnail Menu.
Select Lock/Unlock Clip.
• Changing the index picture
• Adding and deleting shot marks
• Setting and clearing clip flags
A message appears asking you to confirm the
unlocking.
Notes
• Locked clips are deleted along with other clips when a
disc is formatted.
• Clips cannot be locked or unlocked when the write
inhibit tab of the disc is set to the recording disabled
position, or when REC INH in the HOME page of the
function menu is set to ON.
Unlock Clip
C0004
Unlock this Clip?
OK
Cancel
To lock clips
operations.
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
In step 1, you can also perform a shortcut operation by
pressing the STOP button with the SHIFT button held
down.
1
In the clip thumbnail screen, select the thumbnails of
the clips that you want to lock.
2
3
4
Display the Thumbnail Menu.
Select Lock/Unlock Clip.
To unlock all clips
1
2
Display the Disc Menu.
Press the PUSH SET(S.SEL) knob.
Select Lock or Delete All Clips, and then select
Unlock All Clips.
the locked clips.
A message appears asking you to confirm that you
want to unlock all clips.
In step 1, you can also perform a shortcut operation by
pressing the STOP button with the SHIFT button held
down.
3
Select OK to execute the unlock, or Cancel to cancel
it, and then press the PUSH SET(S.SEL) knob.
To lock all clips
1
2
Display the Disc Menu.
Deleting clips
You can delete clips while checking their contents.
Select Lock or Delete All Clips, and then select Lock
All Clips.
A message appears asking you to confirm locking all
clips.
Notes
• Clips cannot be deleted when the write inhibit tab of the
disc is set to the recording disabled position, or when
83
Thumbnail Operations
REC INH in HOME page of the function menu is set to
ON.
• Locked clips cannot be deleted.
• If a deletion target clips is referenced by clip lists on the
disc, all of those clip lists are deleted as well.
• If a deletion target clip is referenced in the current clip
list, only those referencing sub clips are deleted at the
same time as the deletion target clip.
2
3
Select Lock or Delete All Clips, and then select Delete
All Clips.
A message appears asking you to confirm that you
want to delete all clips.
Select OK to execute the deletion, or Cancel to cancel
it, and then press the PUSH SET(S.SEL) knob.
Note
operations.
Locked clips cannot be deleted.
1
In the clip thumbnail screen, select the thumbnail of
the clip that you want to delete.
2
3
Display the Thumbnail Menu.
Select Delete Clip.
A window appears asking you to confirm the deletion.
The window displays thumbnails of four frames from
the target clip (the first frame, two intermediate
frames, and the last frame), along with the name, title1,
date of creation, and duration of the clip.
One of the following messages also appears,
depending on whether the clip is referenced in a clip
list.
• When the clip is not referenced in a clip list:
“Delete Clip”
• When the clip is referenced in a clip list: “Delete
Clip & Clip List” (All clip lists that reference the
target clip are deleted along with the clip.)
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
The selected clip is deleted, and you return to the clip
thumbnail screen.
In step 1, you can also perform a shortcut operation by
pressing the RESET/RETURN button with the SHIFT
button held down.
To delete all clips
1
Display the Disc Menu.
84
Thumbnail Operations
Sub clips (clips in clip lists)
Clips (or parts of clips) that have been added to a clip list
are called “sub clips”. Sub clips are virtual editing data that
specify ranges in the original clips. You can use them
without modifying the original data.
Scene Selection (Clip List
Editing)
The following figure illustrates the relation between clips
and sub clips.
What is scene selection?
Clips on disc
Scene selection is a function which allows you to select
material (clips) from the material recorded on a disc and
perform cut editing. You can do this by operating on this
unit only.
Clip 1
Clip 3
(C0003)
Clip 4
(C0004)
Clip 2 (C0002)
(C0001)
• Scene selection is a convenient way to perform cut
editing in the field and in other offline situations.
• In scene selection you create a clip list (editing data).
Since the material itself is not affected, you can repeat
this any number of times.
Clip list (E0001)
Sub clip 1
Sub clip 2
Sub clip 3
• You can play back the edit list created by scene selection
on this unit.
• In scene selection you can add whole clips or add parts
of a clip. You can add scenes using chapters, change the
playback sequence, and amend or delete In and Out
points. All of these operations can be carried out easily
on this unit.
• Clip lists (editing data) created with the scene selection
function can be used on XPRI and other full-feature
nonlinear editing systems.
In the above example, the whole of clip 2 has been added
as sub clip 1, and the whole of clip 4 has been added as sub
clip 2.
Sub clip 3 is part of clip 3. Therefore, when clip list E0001
is played back, clip 4 is played after clip 2, and then the
part of clip 3 shown in gray color is played.
Clip list editing (current clip list)
To edit a clip list, you need to load the clip list from the
disc into the unit’s internal memory.
The clip list which is currently loaded into the unit memory
is called the “current clip list”.
The current clip list is always the target of sub clip creation
and editing. Clip list playback also uses the current clip
list.
Clips
Material recorded with this unit is managed in units called
clips. A clip contains the material from a recording start
point to a recording end point.
Clips have numbers beginning with C, for example C0001.
After creating and editing a clip list, you need to save it to
disc.
Recording
start point of Recording end
clip 2
point of clip 2
Unit memory
Current clip list
Can be edited (adding, deleting, and
reordering sub clips)
t Clip list playback
and thumbnail
display
Clip 1
(C0001)
Clip 2
(C0002)
Clip 3
(C0003)
Clip 4
(C0004)
SAVE Mm LOAD
Disc
You can also assign titles to your clips and use the titles to
manage them, instead of the clip numbers. For more
information, “Assigning user-defined clip titles”
C0001 (Clip 1)
C0002 (Clip 2)
C0003 (Clip 3)
E0001 (Clip list 1)
E0002 (Clip list 2)
E0003 (Clip list 3)
•
•
•
•
•
•
E0099 (Clip list 99)
Clip lists
You can use the scene selection function to select clips
from the clips saved on a disc and create a cut edit list
called a “clip list”.
Clip lists have numbers beginning with E, for example
E0001. Up to 99 clip lists can be saved on a disc.
Clip list playback
Clips and clip lists are saved together on a disc.
85
Scene Selection (Clip List Editing)
To play a clip list, insert a disc into the unit, load the clip
list that you want to play, and press the PLAY button.
Clips are played according to the data in the clip list.
To add sub clips
You can add sub clips to clip lists from with the clip
thumbnail screen or the clip list thumbnail screen.
However, you must use the clip list thumbnail screen to
edit clip lists.
Creating and editing clip lists
Adding sub clips from the clip thumbnail screen
The following procedure explains operations in the clip
thumbnail screen. You can proceed in the same way in the
expand thumbnail screen and the chapter thumbnail
screen. Expanded blocks are added as sub clips in the
expand thumbnail screen, and chapters are added as sub
clips in the chapter thumbnail screen.
The following table lists the steps in the creation and
editing of clip lists with the scene selection function. To
create a clip list, you always need to carry out the steps
inside the heavy lines. Other steps can be carried out as
required.
1
Add sub clips: Use the Add Sub Clips command to add
the clips you want to use to a clip list. You can add
up to 300 sub clips to one clip list.
This operation can be carried out in the following
thumbnail screens.
operations.
1
In the clip thumbnail screen, select the clip that you
want to add as a sub clip (multiple selections possible).
• Clip thumbnail screen
• Expand thumbnail screen
• Chapter thumbnail screen
• Clip list thumbnail screen
2
3
Display the Thumbnail Menu.
2
Change the sub clip order: Use the Move Sub Clips
command to change the order of sub clips in a clip
list.
Delete sub clips: Use the Delete Sub Clips command
to delete specified sub clips from a clip list.
Trim sub clips: Use the Trim Sub Clip command to
adjust the In and Out points of a sub clip. This
function can also be used to adjust the overall
duration of the clip list.
Select Add Sub Clips, and then press the PUSH
SET(S.SEL) knob.
The Add Sub Clip screen appears.
The clip(s) selected in step 1 appear in the upper part
of this screen, and the clip list appears in the lower
Scene Selection window. The I cursor in the Scene
Selection window indicates the location where the
currently selected sub clip(s) will be inserted.
Set the start timecode: Use the Set Start Time Code
command to set the timecode at the start of a clip
list.
3
4
Play the clip list: Use the PLAY button and other
playback controls to play the current clip list and
check its contents.
Add Sub Clip
002
017/035
Save the clip list: Use the Save Clip List or Save Clip
List as… command to save the newly created clip
list to the disc.
TC 00:30:25:11
TC 00:30:40:13
TC 00:24:34:27
TC 01:01:28:25
TC 00:09:43:14
TC 00:24:24:29
TC 00:24:46:22
TC 00:24:56:24
To reedit clip lists on the disc
TOTAL
00:13:48:24
Scene Selection
Use the Load Clip List command to load the clip lists you
want to edit, and perform the steps 2 to 4 in the previous
section.
You can also delete clip lists on the disc.
To display the total duration after addition of the
selected clip
Press the SHIFT button.
Note
4
5
In the Scene Selection window, move the I cursor to
the location where you want to insert the clip. (The
existing thumbnails arrange themselves to the left and
right of the I cursor.)
Clip lists can be created and edited even when the write
inhibit tab of the disc is set to recording disabled, and when
REC INH on the HOME page of the function menu is set
to ON. However, if you need to save the clip list, set write
inhibit tab and REC INH to enable recording before you
create or edit the clip list.
Press the PUSH SET(S.SEL) knob.
The selected clip is inserted as a sub clip and a “+”
mark appears on the thumbnail in the Scene Selection
window.
86
Scene Selection (Clip List Editing)
To check the addition results
Move the cursor.
the location where the currently selected sub clips will
be inserted.
6
Press the RESET/RETURN button.
To display the total duration after addition of the
selected clips
Press the SHIFT button.
This returns you to the Clip thumbnail screen.
7
8
Repeat steps 1 to 6 as required to add more clips.
5
6
In the Scene Selection window, move the I cursor to
the location where you want to insert the clip. (The
existing thumbnails arrange themselves to the left and
right of the I cursor.)
In step 1, you can hold down the SHIFT button when you
press the PUSH SET(S.SEL) knob. This is a shortcut that
displays the Add Sub Clip screen immediately. You can
also save the clip list immediately in step 5 by executing
the Save Clip List command in the Disc Menu.
Press the PUSH SET(S.SEL) knob.
The sub clips are added at the I cursor position, and
you return to the clip list thumbnail screen.
You can check the results of the addition in that screen.
Adding sub clips from the clip list thumbnail
screen
7
8
Repeat steps 1 to 6 as required to add more clips.
operations.
In step 1, you can also perform a shortcut operation by
pressing the PUSH SET(S.SEL) knob with the SHIFT
button held down.
1
2
Display the Thumbnail Menu.
Select Add Sub Clips, and then press the PUSH
SET(S.SEL) knob.
To add clips from the clip playback screen (quick
insertion)
This method allows you to decide the range to use and add
that range as a sub clip while viewing the video in the clip
playback screen. It does not use GUI screens. You can do
this during recording, playback (including pauses), and
searches.
The Clip List (Add) screen appears.
Clip List (Add)
002
017/035
TC 00:30:25:11
TC 00:30:40:13
TC 01:01:28:25
TC 00:09:43:14
1
Find the point that you want to make the start point of
the sub clip, and then press the PUSH SET(S.SEL)
knob with the B/IN button held down.
TC 00:24:24:29
TC 00:24:34:27
TC 00:24:46:22
TC 00:24:56:24
TOTAL
00:13:48:24
Scene Selection
An In point is set and the IN indicator lights.
2
Find the point that you want to make the end point of
the sub clip, and then press the PUSH SET(S.SEL)
knob with the b/OUT button held down.
3
4
Select the sub clips that you want to add from the
upper part of the screen (the part where 8 thumbnails
are displayed, multiple selections possible).
An Out point is set and the OUT indicator lights. (This
determines the range of the sub clip to be added.)
To select from expanded thumbnails
Press the EXPAND button to display the expand
thumbnail screen.
To check the timecode of the In point or Out point
Press the B/IN button or the b/OUT button.
To select from chapter thumbnails
Press the CHAPTER button to display the chapter
thumbnail screen.
To cue up the In point or Out point
Press the PREV button or the NEXT button with the
B/IN button or b/OUT button held down.
Press the PUSH SET(S.SEL) knob.
To check the duration (time from In point to Out
point)
Press the B/IN and b/OUT buttons at the same time.
The thumbnail selection is confirmed, and an I cursor
appears at the bottom of the Clip List (Add) screen (in
the Scene Selection window). The I cursor indicates
87
Scene Selection (Clip List Editing)
To delete the In point or Out point
Press the RESET/RETURN button with the B/IN or
b/OUT button held down.
5
Press the PUSH SET(S.SEL) knob.
The sub clips are moved to the I cursor position.
6
7
Repeat steps 1 to 5 as required.
3
With the SHIFT button held down, press the PUSH
SET(S.SEL) knob.
A sub clip with the range specified in steps 1 and 2 is
added to the end of the clip list.
To adjust the In and Out points of sub clips
(trim)
Proceed as follows to define the range of a scene by
changing the positions of the In and Out points.
When you specify a range that spans several clips
Sub clips are generated for each of the clips in the
range.
To check the newly added sub clips
You can check the newly added sub clips by
displaying the clip list thumbnail screen.
operations.
1
2
3
In the clip list thumbnail screen, select a thumbnail.
Display the Thumbnail Menu.
4
5
Repeat steps 1 to 3 as required to add more sub clips.
Select Trim Sub Clip, and then press the PUSH
SET(S.SEL) knob.
To reorder sub clips
The Clip List (Trim) screen appears.
Note
001/034
Clip List (Trim)
When this unit is in single clip playback mode (see
page 76), only the selected sub clip can be played.
Total 00:13:48:24
DUR 00:00:21:27
IN
operations.
01:17:33:08
OUT
01:17:55:05
OK
TCR 01:17:33:08
019/035
CLIP
1
In the clip list thumbnail screen, select the thumbnails
of the sub clips that you want to move (multiple
selections possible).
Cancel
Like the clip playback screen, this screen allows you to
play and search all clips on the disc.
2
3
Display the Thumbnail Menu.
Select Move Sub Clips, and then press the PUSH
SET(S.SEL) knob.
To display a list of In and Out point operations that
you can perform
Press the MENU button.
The Clip List (Move) screen appears.
4
5
When you find the point that you want to make the
start point, select “IN” and then press the PUSH
SET(S.SEL) knob.
Clip List (Move)
006
001/034
TC 00:00:00:00
TC 00:04:35:12
TC 00:06:03:03
TC 00:00:21:27
TC 00:04:06:00
TC 00:05:19:08
TC 00:06:46:27
TC 00:04:13:14
TC 00:05:41:05
TC 00:07:08:25
The timecode of the new In point appears in the
timecode display, and the Total (total duration) and
DUR (clip duration) displays are updated.
TC 00:04:57:10
TC 00:06:25:00
When you find the point that you want to make the end
point, select “OUT” and then press the PUSH
SET(S.SEL) knob.
DATE&TIME 08 AUG 2007 11:50
TOTAL DUR 00:13:48:24
The timecode of the new Out point appears in the
timecode display, and the Total (total duration) and
DUR (clip duration) displays are updated.
4
Move the I cursor to the point where you want to move
the selected thumbnails.
88
Scene Selection (Clip List Editing)
To cue up the In point or Out point
Display the Thumbnail Menu, select Cue up Inpoint or
Cue up Outpoint, and then press the PUSH
SET(S.SEL) knob.
To start play from the start of the clip list
Select the thumbnail of the first sub clip.
2
Press the PUSH SET(S.SEL) knob.
To play using the clip list playback screen
To cancel the In point or Out point setting
Display the Thumbnail Menu, select Reset Inpoint or
Reset Outpoint, and then press the PUSH SET(S.SEL)
knob.
1
2
Display the clip list playback screen.
Press the PREV button or the NEXT button to display
the sub clip that you want to play.
The In point or Out point setting returns to the previous
value.
To start play from the first sub clip
Press the SHIFT + PREV buttons to move to the start
of the clip list.
6
Select OK, and then press the PUSH SET(S.SEL)
knob.
3
Press the PUSH SET(S.SEL) knob.
7
8
Repeat steps 1 to 6 as required.
To change the starting timecode of clip
lists
To delete sub clips
The timecode of clip lists is continuous timecode,
unrelated to the timecode of the original clips. By default
the timecode (LTC) of the start of the clip list is
00:00:00:00, but it can be set to any value.
operations.
1
Select the clips to delete in the clip list thumbnail
screen (multiple selections possible).
operations.
2
3
Display the Thumbnail Menu.
1
2
In the clip list thumbnail screen, display the
Thumbnail Menu.
Select Delete Sub Clips, and then press the PUSH
SET(S.SEL) knob.
Select Set Start Time Code, and then press the PUSH
SET(S.SEL) knob.
A message appears asking you to confirm the deletion.
The Set Start Time Code screen appears.
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
Set Start Time Code
5
6
Repeat steps 1 to 4 as required.
TC
2 2 : 3 4 . 5 6 : 1 7
M I N S E C F R M
H
To play the clip list
Preset TC 00:00:00:00
OK
Cancel
Note
When this unit is in single clip playback mode (see
page 62), only the selected sub clip can be played.
3
4
5
Press the B/IN or b/OUT button to select the digit that
you want to change.
operations.
Turn the PUSH SET(S.SEL) konb or the jog dial to
change the value of the digit.
To play using GUI screens
Repeat steps 3 and 4 as required.
1
In the clip list thumbnail screen, select the thumbnail
of the sub clip where you want to start play.
89
Scene Selection (Clip List Editing)
To reset the timecode to 00:00:00:00
Select Reset to Zero in the Thumbnail Menu, and then
press the PUSH SET(S.SEL) knob.
Date(Newest First): Sort by date and time of clip list
creation, newest first.
3
Select the desired clip list name, and then press the
PUSH SET(S.SEL) knob.
To preset the frequently used timecode
Select Save Preset TC in the Thumbnail Menu, and
then press the PUSH SET(S.SEL) knob.
The timecode set in steps 4 and 5 is saved as a preset
value.
To save under the same name
The following procedure saves the current clip list under
its current name (the name that appears in the clip list
thumbnail screen).
To recall the preset timecode
Select Recall Preset TC in the Thumbnail Menu, and
then press the PUSH SET(S.SEL) knob.
operations.
1
2
In the clip list thumbnail screen, display the Disc
6
Press the PUSH SET(S.SEL) knob.
OK is selected.
Select Save Clip List, and then press the PUSH
SET(S.SEL) knob.
7
8
Press the PUSH SET(S.SEL) knob again.
The clip list is saved. However, Save Clip List as... is
executed when the name displayed in the clip list
thumbnail screen is “no name”.
To save clip lists
Note
To save under a specified name
If you press the EJECT button or the on/standby button
before saving a new or edited clip list, a message appears
asking if you want to discard your changes and continue.
Follow the instructions in the message to continue or
cancel the operation.
operations.
1
2
In the clip list thumbnail screen, display the Disc
Menu.
Select Save Clip List as..., and then press the PUSH
SET(S.SEL) knob.
Managing clip lists
A list of clip lists appears.
To load clip lists
The following procedure loads a clip list stored on the disc
into the unit’s internal memory as the current clip list.
Disc Menu
Save Clip List as... Name & Date/Sorted by Name
DVD og BI... 08 AUG2007 11:50
operations.
E0003
E0004
E0005
E0006
E0007
E0095
E0098
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
18 MAY2006 10:25
13 JUN2006 13:43
1
2
In the clip list thumbnail screen, display the Disc
Menu.
Display Select
Select Load Clip List, and then press the PUSH
SET(S.SEL) knob.
To switch the information displayed for clip lists
Press the b/OUT button.
A list of clip lists stored on the disc appears.
With each press, the display changes in the order:
“Name & Date” >“Name & Title” >“Name & Sort
Date” >...
To sort clip lists
Select one of the following orders by selecting
Settings >Sort Clip List by... in the Disc Menu.
Name(A-Z): Sort in ascending order by clip list name.
90
Scene Selection (Clip List Editing)
A list of clip lists appears.
Disc Menu
Load Clip List
DVD og BI... 08 AUG2007 11:50
3
Select the clip list that you want to delete, and then
press the PUSH SET(S.SEL) knob.
Name & Date/Sorted by Name
E0003
E0004
E0005
E0006
E0007
E0095
E0098
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
03 AUG2007 17:51
18 MAY2006 10:25
13 JUN2006 13:43
A message appears asking you to confirm the deletion.
Display Select
Delete Clip List
E0001
Delete this Clip List?
OK
3
Select the desired clip list, and then press the PUSH
SET(S.SEL) knob.
Cancel
The name of the clip list selected here appears in the
clip list thumbnail screen. When you execute the Save
Clip List command in the Disc Menu, the clip list will
be saved under that name.
4
Select OK, and then press the PUSH SET(S.SEL)
knob.
To create a new clip list
Select New File and then press the PUSH SET(S.SEL)
knob.
To sort clip lists
To clear clip lists
The following procedure clears the current clip list from
the unit’s internal memory.
operations.
1
2
3
4
In the clip list thumbnail screen, display the Disc
Menu.
operations.
Select Settings, and then press the PUSH SET(S.SEL)
knob.
1
2
In the clip list thumbnail screen, display the Disc
Menu.
Select Sort Clip List by..., and then press the PUSH
SET(S.SEL) knob.
Select Clear Clip List, and then press the PUSH
SET(S.SEL) knob.
Select one of the following sort methods, and then
press the PUSH SET(S.SEL) knob.
A message appears asking you to confirm that you
want to clear the clip list.
Name(A-Z): Sort in ascending order by clip list name.
Date(Newest First): Sort by date and time of clip list
creation, newest first.
3
Select OK, and then press the PUSH SET(S.SEL)
knob.
Clip lists will be displayed in the specified order the
next time that you carry out an operation such as
loading a clip list.
The current clip list returns to the unnamed state
“(no name)”.
To delete clip lists
The following procedure deletes a clip list from the disc.
operations.
1
2
In the clip list thumbnail screen, display the Disc
Menu.
Select Delete Clip List, and then press the PUSH
SET(S.SEL) knob.
91
Scene Selection (Clip List Editing)
Using planning metadata
Disc Operations
Planning metadata is a file that contains metadata about the
clips to be shot and recorded.
To use planning metadata, you will need to save a file in
advance in the specified location of a media, and insert the
media into this unit.
Checking disc properties
operations.
(page 151) for details.
1
2
Display the Disc Menu.
To load planning metadata files
Select Disc Properties, and then press the PUSH
SET(S.SEL) knob.
operations.
The Disc Properties screen appears.
1
2
Display the Disc Menu.
Select Load Planning Metadata/Select Drive, and then
press the PUSH SET(S.SEL) knob.
A media selection screen appears.
Disc Menu
Load Planning Metadata/Select Drive
Return to Upper Menu
Professional Disc
1), 2)
User Disc ID: User disc ID
1)
USB Flash Drive
Title1: Title1
1), 2)
Title2: Title2
Total DUR: Total recording time
Remain: Remaining recording time
Rewrite: Number of times rewritten
1)This can be specified with the PDZ-1 Proxy Browsing Software on
the supplied XDCAM Application Software CD-ROM.
3
Select the media where your planning metadata file is
stored, and then press the PUSH SET(S.SEL) knob.
2)When the unit’s area of use (UC/J MODEL SELECT) (see page 33)
A list of the planning metadata files stored on the
media appears.
is set to “UC”, titles can be displayed in European languages.
To scroll hidden parts of the string into view
When a b or B mark is displayed for an item, you can
press the B/IN or b/OUT button to scroll the display
by one character for each press.
The V/MARK1 and v/MARK2 buttons scroll the
beginning and end of the string into view.
Disc Menu
Load Planning Metadata/
PM_001_sample
Professional Disc
04 AUG 10:39
04 AUG 10:39
04 AUG 10:39
04 AUG 10:39
PM_002_sample
PM_003_sample
PM_004_sample
To return to the previous screen
Press the PUSH SET(S.SEL) knob.
Name &Date/ Sorted by Name
To edit disc information
You can edit the user disc ID, title1 , and title2 by using a
software keyboard.
4
Select the desired planning metadata file, and then
press the PUSH SET(S.SEL) knob.
1)
The selected planning metadata file is loaded into the
unit’s memory, and the Planning Metadata Properties
screen appears.
1) Only ASCII characters can be used for the title1.
information about operations.
92
Disc Operations
5
Check the information that appears, and press the
PUSH SET(S.SEL) knob.
To clear planning metadata
operations.
To sort planning metadata
You can sort planning metadata by operating in the same
3, select Sort Planning Metadata by....
The planning metadata will be displayed in the specified
order the next time you load planning metadata.
1
2
Display the Disc Menu.
Select Clear Planning Metadata, and then press the
PUSH SET(S.SEL) knob.
A message appears asking if you are sure that you want
to clear the plannning metadata.
To check planning metadata properties
You can check the properties of the planning metadata that
is loaded into this unit’s memory, including the date and
time of creation and the clip titles.
3
Select OK, and then press the PUSH SET(S.SEL)
knob.
The planning metadata is cleared from this unit’s
memory.
operations.
To switch the title display in the display
window
When planning metadata is loaded into this unit, you can
select the format of the title to display in the display
window.
1
2
Display the Disc Menu.
Select Planning Metadata Properties, and then press
the PUSH SET(S.SEL) knob.
The Planning Metadata Properties screen appears.
1
2
Display the Disc Menu.
Select Settings, and then press the PUSH SET(S.SEL)
knob.
3
Select Planning Clip Name in Clip Info. Area and then
press the PUSH SET(S.SEL) knob.
information area.
File Name: Planning metadata file name
Assign ID: Assign ID
Created: Date and time of creation
4
Select one of the following, and then press the PUSH
SET(S.SEL) knob.
Modified: Date and time of most recent modification
Modified by: Name of person who modified the file
Off: Do not display a title.
ASCII Clip Name: Display the ASCII format title
1)
Title1: Title 1
Title2: Title 2
Material Gp: Material group name
1)This can be set as the clip name (see page 151).
To scroll hidden parts of the string into view
When a b or B mark is displayed for an item, you can
press the B/IN or b/OUT button to scroll the display
by one character for each press.
Checking user-defined essence
marks
The V/MARK1 and v/MARK2 buttons scroll the
You can display the names of user-defined Shot Mark0 to
Shot Mark9 essence marks in planning metadata (UTF-8
format, maximum 32 bytes).
beginning and end of the string into view.
To return to the previous screen
Press the PUSH SET(S.SEL) knob.
93
Disc Operations
1
2
Display the Planning Metadata Properties screen (see
page 93) for the planning metadata loaded into this
unit.
To exit the formatting screen
Press the PUSH SET(S.SEL) knob with Exit selected.
To disable the Format Disc command
To prevent inadvertent disc formatting, resulting in the
loss of recorded data, you can disable the Format Disc
command.
The , button is enabled when the planning metadata
Press ,, and then turn the PUSH SET(S.SEL) knob.
The User Defined Essence Marks screen appears.
1
2
Display the Disc Menu.
Select Settings, and then press the PUSH SET(S.SEL)
knob.
3
4
Select Disable “Format Disc”, and then press the
PUSH SET(S.SEL) knob.
Select Disable, and then press the PUSH SET(S.SEL)
knob.
Formatting discs
Displaying disc and clip properties
in a web browser
operations.
By connecting this unit and a computer over a network,
you can display disc properties and clip properties in a web
browser installed on the computer (Web Thumbnail
function).
The Clip Properties page also allows you to download
high-resolution clip data, proxy AV data, and metadata
from this unit and to save that data on your computer.
1
2
Display the Disc Menu.
Select Format Disc, and then press the PUSH
SET(S.SEL) knob.
A message appears asking you to confirm the format.
Format Disc
To display the unit’s XDCAM web pages
All Clips, Clip Lists and
Non-AV Data (General Files)
will be Deleted.
1
2
Connect this unit and a computer to a network (see
Format OK?
Start the browser on the computer, and enter “http://”
+ IP_address_of_this_unit + “/” in the address bar of
the browser, and then press the Enter key.
OK
Cancel
For example, if the IP address of this unit is
“192.168.001.010”, enter “http://192.168.1.10/”.
If the connection succeeds, you will be prompted to
enter a user name and a password.
3
Select OK, and then press the PUSH SET(S.SEL)
knob.
To cancel the format
Select Cancel, and then press the PUSH SET(S.SEL)
knob.
3
Enter your user name and password, and then press the
Enter key.
The user name and password are set to the following
when the unit is shipped from the factory.
• User name: admin
• Password: Model name (“pdw-f1600” or “pdw-
hd1500”)
To continue by formatting another disc
Exchange the disc, select OK, and then press the
PUSH SET(S.SEL) knob.
94
Disc Operations
After the user name and password are verified, an
XDCAM web page appears.
To display disc and clip properties
1
Insert a disc into this unit, and put this unit into the
following state.
• Recording, playback, search and other disc
operations: Stopped
• THUMBNAIL button: Off
• Disc access by Lock or Delecte All Clips, Format
Disc, and so on in the Disc Menu: Stopped
• FAM or FTP connection for file operations:
Disconnected, or logged out
2
Display the XDCAM web pages in the browser of your
computer (see the previous section).
When multiple pages exist, you can switch pages by
clicking << (back five pages), < (back one page), >
(forward one page), or >> (forward five pages).
To display disc properties
Click “Disc Properties” in the Disc menu.
The disc properties of this unit appear in the Disc
Properties page.
To display clip properties
In the Thumbnails page, select a clip by clicking its
thumbnail.
The properties of that clip appear in the Clip Properties
page.
information about the various properties.
information about the various properties.
To display clip thumbnails
Click “Thumbnails” in the Disc menu.
A page of thumbnails of clips on the disc appears.
Each thumbnail page displays up to 12 thumbnails.
To download high-resolution clip data (HIGH
resolution file), proxy AV data (LOW resolution file),
or metadata (Clip NRT metadata), click the Download
button to the right of the item that you want. Then click
“Save” in the dialog that appears and specify the save
destination.
The specified data is downloaded to the specified
location in your computer.
95
Disc Operations
Notes
• The characters that can be used in the names of clip-
related data files are single-byte letters, numbers,
and symbols. However, the following symbols
cannot be used.
" # * / : < > ? \ |
• If you click “Cancel” in the download dialog, or if
the download is cancelled in some other way with
the browser still connected to the unit by FTP, click
“Back to Thumbnails” to return to the thumbnails
screen, or exit the web browser.
96
Disc Operations
Transferring clips (Direct FTP function)
You can transfer clips (MXF files) between this unit and
Transfer direction Transfer target
Function
external devices over a network. This unit has an Direct
FTP function, which allows you to connect to any
XDCAM device or computer with an FTP server function
and transfer files with a few simple operations in the GUI
screen.
Download
One clip
get
Note
File transfers with this function are limited to clips (high-
resolution data) and clip list files. To transfer files of other
types (proxy AV data, files in the General and User Data
directories, and so on), operate after establishing a FAM or
The following table lists the types of file transfers that this
unit can execute.
Transfer direction Transfer target
Function
Upload
One or more clips
Multiple clips with clip list
Part of one clip
put
partial put
Upload clip (put)
Download clip (get)
PDW-HD1500
Network
a)
Laptop computer
Local host (this unit)
a) The following software requirements must be satisfied.
•
•
An FTP server function must be available.
In the case of Windows, Microsoft Window IIS (Internet Information
Service) Version 7.0 or higher.
Material server
Remote server
•
In the case of Macintosh, Mac OS X Version 10.5.6 or higher.
• For XDCAM devices that support UPnP (universal plug
and play), the UPnP function must be enabled (the
setting may vary).
Preparations for clip transfers
Check the following points.
• This unit must be connected over a network to the
transfer target device (XDCAM device or computer).
• The settings under maintenance menu item M5:
NETWORK must be set to values that allow network
connections.
To enable the UPnP function
The UPnP (universal plug and play) function allows
devices to be easily connected to networks. The following
XDCAM devices support UPnP.
• PDW-F1600
• The remote control switch must be set to NET.
• PDW-HD1500
• PDW-F800
97
Transferring clips (Direct FTP function)
• PDW-700
• PDW-740
Note
If the remote host is a computer, clips are transferred
with the UMID unchanged regardless of this setting.
To enable the UPnP function on this unit, set maintenance
menu item M59: UPnP to ENABLE.
To reconnect to a remote host
The Reconnect button is enabled if the most recent
operation successfully established a connection to a
remote host.
For the settings on other XDCAM devices, refer to the
operation manuals supplied with the devices.
You can select “Reconnect” and press the PUSH
SET(S.SEL) knob to reconnect to that host. The host is
selected automatically and the screen changes directly
to the Connecting Status screen (see step 9 in the
procedure).
Uploading clips
To upload entire clips
Proceed as follows to upload selected clips or all clips and
clip lists on the disc.
Note
The Reconnect button is not enabled if the most recent
operation failed to connect to a remote host.
operations.
5
Select ,, and then press the PUSH SET(S.SEL)
knob.
1
In the clip thumbnail screen, select the clip to upload
(multiple selections possible).
The Select Remote Host screen appears.
To upload all clips and clip lists on the disc, start from
step 2.
2
3
Display the Thumbnail Menu.
Select Upload Clips via Direct FTP, and then press the
PUSH SET(S.SEL) knob.
The Select Transfer Type screen of the Upload Clips
via Direct FTP command appears.
6
Select the remote host (the target device to which you
want to transfer the clips).
You can register up to four remote hosts.
Remote Host 1 to 3: Register these in the settings
screen.
Remote Host 4(UPnP): A remote host that supports
UPnP (universal plug and play) is detected and
registered automatically (see “To enable the
4
Select the type of clip transfer.
To check remote hosts discovered by the UPnP
function
Select “Hosts Discovered via UPnP”, and then press
the PUSH SET(S.SEL) knob. (If the UPnP function of
this unit is disabled, a confirmation screen appears
prompting you to enable it. Select “OK” and then press
the PUSH SET(S.SEL) knob.
The Select Host Discovered via UPnP screen appears.
(Some time may be required before the search for
remote hosts finishes.)
Selected Clips: Clips selected in step 1.
All Clips & ClipList: All clips and clip lists on the
disc.
To transfer while preserving the UMID of the
transfer source clips
Check the “UMID Unchanged” option.
Select the name of a remote host from the list, and
press the PUSH SET(S.SEL) knob. A network settings
98
Transferring clips (Direct FTP function)
screen appears (see step 7). If you establish a
Item
Setting
connection with the selected remote host, the network
settings are saved in Remote Host 4. From the next
time that you select “Remote Host 4(UPnP)”, the
remote host that you select here will be connected.
Device Type
The type of the remote host
• If the remote host is an XDCAM
device, select the model name or
“Other XDCAM model” (if the model
name is not in the list) from the list of
a)
model names.
To check the network settings of this unit
Select “Network Config”, and then press the PUSH
SET(S.SEL) knob. The following network settings
appear.
• If the remote host is a computer,
select “Others(PC Server)” from the
list of model names.
Description
Comment about the remote host. (UTF-
8 encoding, up to 128 characters. This
setting has no effect on the connection.)
The setting that you make here appears
as the remote host name in the Select
Remote Host screen (see step 5 of the
procedure).
Item
Setting
Host Name
IP Address
Host name
a)
IP address
Subnet Mask
DHCP
Subnet mask
Path
If the remote host is a computer, path to
the transfer destination directory. (This
is not needed if the remote host is an
XDCAM device.)
Setting that specifies whether to
acquire the IP address
automatically from a DHCP server
Enabled: Acquire automatically
Disabled: Do not acquire
automatically
User Name
Password
User name for FTP login. (If the remote
host is an XDCAM device, the default is
“admin”.)
Address Status
Method used to set IP address
Manual Set: Manually
DHCP: DHCP function
AutoIP: Auto IP addressing
function
Password for FTP login. (If the remote
host is an XDCAM device, the default is
the model name, such as “pdw-
hd1500”.)
Undefined: Nothing specified
a) If an XDCAM device is selected as the Device Type, then the User
Name and Password are set automatically to the default, and you do
not need to make the Port and Path settings. Simply selecting the
Host Name (or as appropriate the Description) is enough to fulfill the
requirements for connection.
Default Gateway
Default gateway
a) An IP address determined by a DHCP server appears instantly in this
field.
Select OK and press the PUSH SET(S.SEL) knob to
return to the previous screen.
If the User Name or Password of the device that you
want to connect to changes, set them here.
7
Select ,, and then press the PUSH SET(S.SEL)
8
9
Set the various items.
knob.
A network settings screen for the remote host appears.
To select an item
Turn the PUSH SET(S.SEL) knob to move the cursor,
and then push the PUSH SET(S.SEL) knob.
A software keyboard appears so that you can enter a
setting.
Select “Connect”, and then press the PUSH
SET(S.SEL) knob.
The settings are saved and the Connecting Status
screen appears.
Item
Setting
Host Name
Host name or IP address. (If this is a
host name, a DNS server must be
available on the connected network.
Specification of an IP address is
recommended.)
Port
Port used by the FTP server (normally
“21”).
99
Transferring clips (Direct FTP function)
To check the connection on the remote host side
If the remote host is an XDCAM device, check that the
“NETWORK!” has appeared in the display or other
status display location.
The following table lists the various stages that appear
in the connection status screen and describes the
corresponding processing.
Item
Description
The progress bars show the progress of the transfer. If
multiple clips are being transferred, a count of the clips
that have been successfully transferred appears.
If the remote host is an XDCAM device, the disc usage
also appears. (It does not appear if the remote host is a
computer).
DNS Name
Resolving
When host was specified by a
host name instead of an IP
address, the unit is querying a
DNS server for the host’s IP
address.
ping - echo back
The unit has issued a ping
(communications established)
command and is waiting for a
response.
If a file of the same name already exists at the
transfer destination
Open Remote Host The unit is connecting to the
The file name is changed so that it does not conflict
with the file at the destination.
remote host over the specified
port.
The name of the file on the transfer source (this unit)
appears in the “Original” field, and the name of the file
on the transfer destination appears in the “Copy”
FTP Login
The unit is logging in to the
remote host with specified user
name and password.
1)
field.
Change Directory When a path was specified, the
unit is changing to the specified
directory.
1) If the clip name is a standard name, it is changed to the unused clip
name with the smallest number. (Example: If names C0001 to C0020
are in use, the name C0021.)
If the clip name is a user-defined name, a serial number is appended
to the clip name. (Example: If the name is EveningNews,
EveningNews(1).)
The status indicated beside each item lights in yellow
during processing for that item, and lights in green
when the processing finishes.
To cancel the processing
Do one of the following.
• Select “Abort: Immediately”, and then press the
PUSH SET(S.SEL) knob.
• If you are transferring multiple clips, select “Abort:
After this clip”, and then press the SET/S.SEL
button or the MENU knob. (The transfer of
subsequent clips will be cancelled after transfer of
the current clip finishes.)
If an error occurs
The status indicator changes to red.
Correct the condition that caused the error and repeat
the operation.
If you cannot connect
Check the following points.
• Make sure that this unit and the remote host are
correctly connected to the network.
• If the remote host is an XDCAM device, make sure
that it is not displaying a GUI screen.
• If the remote host is an XDCAM device, make sure
that a disc is inserted.
• Set the remote control switch of the unit to
“LOCAL”.
Note
When several files are to be transferred, the entire
transfer task is cancelled when the first transfer failure
occurs. Subsequent clips are not transferred.
When the connection is complete (the indicators of all
items have turned green), the Upload Clips via Direct
FTP screen appears.
When the transfer of all files has finished, the
Uploading Result Report screen appears.
Press the PUSH SET(S.SEL) knob. This returns you to
the clip thumbnail screen.
100
Transferring clips (Direct FTP function)
operations.
1
2
Display the Disc Menu.
Select Download Clip via Direct FTP, and then press
the PUSH SET(S.SEL) knob.
The Select Remote Host screen of the Download Clip
via Direct FTP command appears.
To upload part of a clip
You can select part of a clip in the expand thumbnail
screen or the chapter thumbnail screen and upload that
part.
Expand thumbnail screen: The clip is divided arbitrarily
into parts of equal length, regardless of content. Use
this method if you do not need to specify the transfer
range precisely.
Chapter thumbnail screen: Use this method if you want
to transfer a specific range. (By setting essence marks
at the start point and end point of the transfer range,
you can specify the range with a precision of one
frame.)
3
If the connection succeeds, the Select Clip to
Download screen appears.
1
In the clip thumbnail screen, select a clip and press the
EXPAND or CHAPTER button.
The expand thumbnail screen or the chapter thumbnail
screen appears.
2
Select the transfer range.
To select multiple thumbnails
While holding the SHIFT key down, turn the PUSH
SET(S.SEL) knob, or press the B/IN or b/OUT button.
The duration of the transfer range appears in the lower
right of the screen.
Notes
• If the remote host is a computer, only the MXF files
in the specified directory appear.
• File names containing other than ASCII characters
(kanji and so on) are not displayed.
Note
When the selected range (duration) in the expand
thumbnail screen is less than two seconds, it is
expanded automatically to two seconds.
4
Select a clip to download, and then press the PUSH
SET(S.SEL) knob.
3
Execute step 2 to 9 of the previous section “To upload
entire clips”.
The download starts.
When the download finishes, the Downloading Result
Report screen appears.
Select “OK”, and then press the PUSH SET(S.SEL)
knob. This returns you to the clip thumbnail screen.
Downloading clips
Proceed as follows to download clips from a remote host
(such as other XDCAM device devices or a material
server).
101
Transferring clips (Direct FTP function)
The Select Remote Host screen appears.
Copying clips directly between
XDCAM devices
9
Select “Hosts Discovered via UPnP”, and then press
the PUSH SET(S.SEL) knob.
In the field or another environment where the devices are
not connected to a network, you can copy (upload) clips
between XDCAM devices by connecting them directly.
The example in the following procedure shows how to
copy a clip from this unit to a PDW-HD1500. Insert discs
into both units and proceed as follows.
The detected connection destination device (the PDW-
HD1500) appears in the Select Host Discovered via
UPnP screen.
10Press the PUSH SET(S.SEL) knob.
Detailed information about the connection destination
device (the PDW-HD1500) appears.
1
Connect this unit and the PDW-HD1500 by a network
cable.
The cable can be either a cross cable or a straight cable.
11With “Connect” selected, press the PUSH
SET(S.SEL) knob.
Transfer of the clip begins as soon as the connection is
established.
During transfer of the clip, “NETWORK!” appears in
the display of the connection destination device (the
PDW-HD1500).
This unit
Network cable
(not supplied)
When transfer of the clip completes, an Uploading
Result Report appears on the screen.
Press the PUSH SET(S.SEL) knob to return to the clip
thumbnail screen.
PDW-HD1500
12Check the copied clip in the clip thumbnail screen of
the connection destination device (the PDW-
HD1500).
2
Set up the two units as follows.
Item
Setting
Item M50: DHCP in the Maintenance menu ENABLE
Item M59: UPnP in the Maintenance menu ENABLE
3
4
Power both units off and on again, and wait for about
three minutes.
Check that the IP addresses of the two units have been
set as follows by the Auto-IP function.
Item
Item M51: IP ADDRESS PRESET 169.254.XXX.XXX
in the Maintenance menu (X: any number)
Setting
5
In the clip list thumbnail screen of this unit, select the
clip to copy (upload).
6
7
Display the Thumbnail Menu.
Select Upload Clips via Direct FTP, and then press the
PUSH SET(S.SEL) knob.
With , selected, the Select Transfer Type screen of
the Upload Clips via Direct FTP command appears.
8
Press the PUSH SET(S.SEL) knob.
102
Transferring clips (Direct FTP function)
Shortcut List
You can access many functions from the buttons, without
displaying a menu (shortcut operations).
Shortcuts are available for the following functions. The
plus sign (+) indicates that one button is held down while
another is pressed, for example “SHIFT + RESET/
RETURN”.
Note
The same shortcut may access different functions,
depending on the screen that is active when it is executed.
Function
Operation
Clip List Thumbnail (display the clip list thumbnail screen) SUB CLIP
Expand Thumbnail (display expand thumbnail screen)
Chapter Thumbnail (display chapter thumbnail screen)
EXPAND
CHAPTER
Essence Mark Thumbnail (display essence mark
thumbnail screen)
SHIFT + THUMBNAIL
Add Sub Clip (add sub clip)
Delete Clip (delete clip)
SHIFT + PUSH SET(S.SEL) knob
SHIFT + RESET/RETURN
SHIFT + STOP
Lock/Unlock Clip (lock or unlock clip)
Set Inpoint (set In point)
B/IN + PUSH SET(S.SEL) knob
b/OUT + PUSH SET(S.SEL) knob
B/IN + PREV or B/IN + NEXT
b/OUT + PREV or b/OUT + NEXT
B/IN + RESET/RETURN
Set Outpoint (set Out point)
Cue up Inpoint (cue up In point)
Cue up Outpoint (cue up Out point)
Reset Inpoint (reset In point)
Reset Outpoint (reset Out point)
Cue up (cue up)
b/OUT + RESET/RETURN
a)
PUSH SET(S.SEL) knob
b)
Cue up & Play (cue up and play)
PLAY
Page Down (switch to next page)
Page Up (switch to previous page)
Go To End (go to the last item)
SHIFT + v/MARK2
SHIFT + V/MARK1
SHIFT + NEXT
Go To Top (go to the first item)
SHIFT + PREV
Select Multi Clip (select multiple clips)
Exit (exit the current thumbnail screen)
SHIFT + b/OUT or SHIFT + B/IN
THUMBNAIL
a) If Settings >SET Key on Thumbnail in the Disc Menu is set to “Cue up &
Play”, then playback starts as soon as cueup is ready.
b) If Settings >SET Key on Thumbnail in the Disc Menu is set to “Cue up &
Play”, then pressing the PUSH SET(S.SEL) knob has the same effect.
103
Shortcut List
File Operations
6
Chapter
Overview
A remote computer can be connected to this unit and used
to operate on recorded data which has been saved in data
files, such as video and audio data files.
There are two ways to connect a remote computer.
• FAM connection
Connect the (i.LINK) S400 connector on this unit to
the i.LINK (IEEE1394) connector on the remote
• FTP connection
Connect the network connectors on this unit and the
Directory structure
The following figure shows the directory structure of discs
visible to a remote computer.
Note
This structure is not the same as the actual structure
recorded on the disc.
(Continued)
a) Root directory
b) Only when sub item NAMING FORM of setup menu item 036 is set to
“free”
104
Overview
(Continued)
File operation restrictions
This section explains which operations are possible on
files stored in each directory.
Write: Write data sequentially from the start to the end of
the file.
When required, the following operation tables distinguish
reading and writing from partial reading and writing.
Read: Read data sequentially from the start to the end of
the file.
Partial write: Write data to a part of the file only.
Note
Operations other than Read and Partial read are possible
only when the Write Inhibit tab of the disc is set to
recording enabled.
Partial read: Read only a part of the data in the file.
Root directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
INDEX.XML
ALIAS.XML
Contains data for management of the Yes
material on the disc.
No
No
No
No
a)
Contains conversion tables for
assigning user-defined names to clips
and clip lists.
Yes
No
No
No
No
b)
DISCMETA.XML Contains metadata to indicate the
disc properties.
Yes
Yes
No
No
No
No
No
No
No
MEDIAPRO.XML Contains a list of material on the disc, Yes
basic properties, related information,
and information about access
methods.
SYSPRO.XML
Other files
Contains information about device
system settings and menu settings.
Yes
–
No
No
No
–
No
No
No
–
Files other than the above
a) Only when sub item NAMING FORM of setup menu item 036 is set to
“free”
Notes
b) Only files which can be written by XDCAM
• Directories cannot be created in the root directory.
105
Overview
• The directories in the root directory (Clip, Edit, Sub,
UserData, General, and PROAV) cannot be deleted or
renamed.
Clip directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
b), c)
d)
b)
e)
a)
Clip file created by recording (MXF
file)
Yes
Yes
Yes
Yes
Yes
*
C .MXF
*: 0001 to 9999
f)
g)
h)
i)
a)
Metadata file generated automatically Yes
when C .MXF file is created.
*: 0001 to 9999
Yes
No
No
No
No
*
C M01.XML
*
i)
a)
f)
g)
f)
User metadata file. This type of file is
generated automatically during recording
via an FTP or FAM connection when the
unit recognizes that an MXF file contains
metadata that was generated by a non-
XDCAM device.
Yes
Yes
C*M02.KLV
Yes
No
Yes
*: 0001 to 9999
Other files
Files other than the above
–
–
No
–
a) The unit can handle files with user-defined names in the “C*” part.
g) When the “C*” part of a C*.MXF file name is changed, a C*M01.XML
file and a C*M02.KLV file with the same name in the “C*” part is also
changed automatically.
h) When a C*.MXF file is created, a C*M01.XML file with the same name
in the “C*” part is created automatically.
b) Only files which are 2 seconds or longer in length, in a format matching
the format (system frequency) and recording format (MPEG HD and
number of audio channels) of the recorded sections of the disc, and which
can be overwritten by XDCAM. (Partial writing is not possible.)
c) Overwriting is not possible.
i) When a C*.MXF file is deleted, a C*M01.XML file and a C*M02.KLV
file with the same name in the “C*” part is also deleted automatically.
d) Only when sub item NAMING FORM of setup menu item 036 is set to
“free”.
e) Any clip may be selected and deleted.
f) Only files which can be written by XDCAM
Note
Directories cannot be created in the Clip directory.
Edit directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
b)
c)
d)
a)
Clip list file
*: 0001 to 0099
Yes
Yes
Yes
Yes
Yes
*
E E01.SMI
b)
e)
f)
g)
a)
Metadata file generated automatically Yes
when E*E01.SMI file is created.
*: 0001 to 0099
Yes
No
–
No
No
No
–
*
E M01.XML
Other files
Files other than the above
–
No
a) The “E*” part can be changed to a user-defined name.
b) Only files which can be written by XDCAM. Partial writing is not
possible.
c) Only when sub item NAMING FORM of setup menu item 036 is set to
“free”.
Note
Directories cannot be created in the Edit directory.
d) Only files which can be written by XDCAM
e) When the “E*” part of an “E*01.SMI” file name is changed, an
E*M01.XML file with the same name in the “E*” part is also changed
automatically.
f) When an E*E01.SMI file is created, an E*M01.XML file with the same
name in the “E*” part is also generated automatically.
g) When an E*E01.SMI file is deleted, an E*M01.XML file with the same
name in the “E*” part is also deleted automatically.
106
Overview
Sub directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
b)
c)
d)
a)
Proxy AV data (MXF) file generated
automatically when a C*.MXF file is
created.
Yes
No
No
No
No
*
C S01.MXF
*: 0001 to 9999
Other files
Files other than the above
–
No
–
No
–
a) The “C*” part can be changed to a user-defined name.
Note
b) When the “C*” part of a C*.MXF file name is changed, a C*S01.MXF file
with the same name in the “C*” part is generated automatically.
c) When a C*.MXF file is created, a C*S01.XML file with the same name in
the “C*” part is generated automatically.
Directories cannot be created in the Sub directory.
d) When a C*.MXF file is deleted, the C*S01.XML file with the same name
in the “C*” part is also deleted automatically.
UserData directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
a)
Any file
Yes
Yes
Yes
Yes
Yes
a) UTF-8 file names can be up to 63 bytes in length. (Depending on the
character type, file names (including extension) may be limited to 21
characters.)
The following directory operations are possible in the
UserData directory.
• Directory creation (up to 62 levels, including the
UserData directory)
• Deletion and renaming of directories
General directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create Delete
a)
Any file
Yes
Yes
Yes
Yes
Yes
a) UTF-8 file names can be up to 63 bytes in length. (Depending on the
character type, file names (including extension) may be limited to 21
characters.)
- Symbols: ", *, /, :, <, >, ?, \, |
1) The following character codes cannot be used by FAM connections.
U+010000, U+020000, U+030000, U+040000, U+050000, U+060000,
U+070000, U+080000, U+090000, U+0A0000, U+0B0000, U+0C0000,
U+0D0000, U+0E0000, U+0F0000, U+100000
The following directory operations are possible in the
General directory.
• Directory creation (up to 63 levels, including the
General directory)
• Deletion and renaming of directories
PROAV directory
This directory contains individual files recorded on the
disc.
To display the PROAV directory, set maintenance menu
item M33: FILE I/F CONFIG > PROAV DISPLAY to
“ENABLE”.
Notes
• The maximum number of files that can be created on a
disc is 5,000 for single-layer discs and 6,000 for dual-
layer discs (both including directories).
• File names and directory names can use letters, numbers,
and symbols from the Unicode 2.0 (UTF-8) character
set.
Assigning user-defined clip titles
However, the following control characters and
symbols cannot be used.
- Control characters: U+0000 to U+001F, U+007F
By default, clips on each disc are assigned names in the
range C0001.MXF to C9999.MXF. For this reason, two
discs can contain clips with the same names. The
1)
107
Overview
automatic title generation function allows you to assign
titles to all of the clips on several discs, which facilitates
clip management. For example, if the titles TITLE00001 to
TITLE00020 are assigned to clips C0001.MXF to
C0020.MXF on disc 1, then the titles TITLE00021 to
TITLE00037 are assigned to clips C0001.MXF to
C0017.MXF on disc 2.
5
6
Turn the PUSH SET(S.SEL) knob to select “enable”,
and press the knob.
The automatic title generation function is enabled.
Turn the PUSH SET(S.SEL) knob to move the asterisk
(*) on the left of the menu items to the item you want
to select, and press the knob.
PREFIX: A string of up to 10 characters. The
allowable characters are alphanumeric characters,
symbols (! # $ % & ' ( ) + ,- . ; = @ [ ] ^ _ { } ~),
and the space character.
NUMERIC: A five-digit number (00001 to 99999) to
serve as the initial value of the serial number.
C0020.MXF
0002.MXF
C0001.MXF
TITLE00020
TITLE00002
TITLE00001
7
8
9
Turn the PUSH SET(S.SEL) knob to select the
character position to set, and press the knob.
Clips recorded on Disc 1
Turn the PUSH SET(S.SEL) knob to select the
character to set.
C0017.MXF
Repeat steps 7 and 8 as required.
0002.MXF
C0001.MXF
When you are setting the “NUMERIC” item, you can
press the RESET/RETURN button to return the initial
value of the serial number to 00001 (factory default
setting).
TITLE00037
TITLE00022
TITLE00021
Clips recorded on Disc 2
10Carry out steps 7 to 9 to set the other item.
Proceed as follows to specify a title and assign it to
recorded clips.
11Press the SAVE function (F5) button.
The title is saved.
1
2
Press the MENU button.
To check the titles of recorded clips
Press the THUMBNAIL button to display the thumbnail
screen, and select the clip whose title you want to check.
The title of the selected clip appears at the upper left of the
screen.
Turn the PUSH SET(S.SEL) knob to select setup
menu item 035, and press the knob.
3
Turn the PUSH SET(S.SEL) knob to select “on”, and
press the knob.
information about the thumbnail screen.
The clip title naming screen appears.
RETURN
Notes
ITEM-035
SELECT
• The value of the serial number is incremented by 1 every
time a title is generated. When the value reaches 99999,
the next number restarts from 00001.
• Duplicate clip titles can be generated if you reset the
serial number after recording several clips or the same is
true depending on the value setting. Care should be taken
when setting the serial number.
CLIP TITLE NAMING
SELECT
*TITLE
PREFIX
NUMERIC
- disable
- TITLE
- 00001
SAVE
EXIT
SETUP
• The “PREFIX” setting is saved in memory banks, but the
4
Turn the PUSH SET(S.SEL) knob to move the asterisk
(*) on the left of the menu items to “TITLE”, and press
the knob.
The asterisk indicates the selected item.
108
Overview
Command prompt FTP commands do not support
UTF-8.
Assigning user-defined clip and clip
list names
The following standard format names are assigned
automatically to clips and clip lists that are created or
recorded by XDCAM devices.
C0001.MXF
Clips: C0001.MXF to C9999.MXF
Clip lists: E0001E01.SMI to E0099E01.SMI
This unit can handle clips and clip lists with user-defined
names as well as names in the standard format.
TITLE00001
Limitations
When the “AUTO NAMING” sub item of setup menu
item 036 is set to “C****”
• Letters, numbers and symbols from the Unicode 2.0
character set can be used.
However, the following control characters and symbols
cannot be used.
- Control characters: U+0000 to U+001F, U+007F
- Symbols: ", *, /, :, <, >, ?, \, |
TITLE00001.MXF
• Depending on the character type, the length of user-
defined names (the “C*” or “E*E01” part) may be
limited to 14 characters. (The limit for ASCII characters
is 56 characters.)
TITLE00001
• All file name extensions are converted automatically to
uppercase.
When the “AUTO NAMING” sub item of basic menu item
036 is set to “title”
• Titles are used as user-defined clip names on this unit.
Therefore, the available characters are limited to those
supported by the title function.
• Files generated along with clips and clip lists use the
same names (the “C*” or “E*” part of the following file
names).
- Clips: Metadata files (C*M01.XML), user metadata
files (C*M02.KLV), proxy AV data files
(C*S01.MXF)
- Clip lists: Metadata files (E*M01.XML)
• The following names cannot be assigned.
- Clips: C0000.MXF
1
Before you start, set the “TITLE” sub item of setup
menu item 035 CLIP TITLE NAMING SELECT to
“enable”, and set a title (see the previous section).
2
3
Press the MENU button.
Turn the PUSH SET(S.SEL) knob to select setup
menu item 036.
4
Turn the PUSH SET(S.SEL) knob to move the “*” to
the left of the item names to “NAMING FORM”.
- Clip lists: E0000E01.SMI, E0100E01.SMI to
E9999E01.SMI, E0000.SMI, E0100.SMI to
E9999.SMI
The “*” indicates the selected item.
• The following names should be avoided.
- Clips: C5000.MXF to C9999.MXF
- Clip lists: E0001.SMI to E0099.SMI
RETURN
ITEM-036
SELECT
FILE NAMING
* NAMING FORM
AUTO NAMING
END
- C****
- C****
To assign clip names on this unit
The title assigned to clip becomes its clip name (file
name).
SAVE
EXIT
SETUP
Notes
• When the first letter of the title setting with setup menu
item 035 CLIP TITLE NAMING SELECT is a space or
period (.), the clip name is the title string minus the first
letter.
• An FTP client that supports UTF-8 is required to use
Unicode characters other than ASCII characters.
5
Turn the PUSH SET(S.SEL) knob to select “free”, and
press the knob.
You are now able to use clips and clip lists with user-
defined names.
109
Overview
6
7
8
Turn the PUSH SET(S.SEL) knob to move the “*” to
the left of “AUTO NAMING”, and press the knob.
File Operations in File
Access Mode (for
Windows)
Turn the PUSH SET(S.SEL) knob to select “title”, and
press the knob.
Press the SAVE function (F5) button.
The same name will now be given to newly recorded
clips.
File access mode operating environment
Operating system requirements for file operations by file
access mode (called FAM below) are as follows.
• Computer operating system: Microsoft Windows XP
Professional SP2 or later, or Microsoft Windows Vista
Ultimate/Business (32-bit)
To use clips and clip lists with user-defined
names over FAM and FTP connections
Carry out steps 2 to 5 of “To assign clip names on this
unit”, and then press the SAVE function (F5) button.
It is now possible to write, transfer, and rename clips and
clip lists with user-defined names over file access mode
Note
64-bit editions of Windows Vista are not supported.
Preparations
Install the FAM driver on the remote computer (see the
next section).
Fuji.MXF
To install the FAM driver
Insert the supplied CD-ROM (XDCAM Application
Software) into the CD-ROM drive of your computer,
navigate to the FAM Driver directory, and run the installer
in the directory for your operating system, then follow the
installation instructions.
Able to use clips with user-defined names
over FAM and FTP connections
For details, refer to the ReadMe file contained on the CD-
ROM disc.
Sakura.SMI
Note
Able to use clip lists with user-defined names
over FAM and FTP connections
Use Version 2.10 or higher of the FAM driver. The FAM
driver on the supplied CD-ROM is Version 2.10 or higher.
If a FAM driver is already installed on your computer,
check the version.
To check clip names
Press the THUMBNAIL button to display the thumbnail
screen, and select the clip whose name you want to check.
The name of the selected clip appears at the upper left of
the screen.
To check the version
On Windows XP
information about the thumbnail screen.
Select “ProDisc” from “Add or Remove Programs” in the
control panel, and then click “Click here for support
information”.
Note
On Windows Vista
(1) Open “Programs” >“Programs and Functions” in the
control panel, and then right click the header (where
“Name” and “Supplier” are displayed) and select
“Other...”.
(2) In the Advanced Settings dialog, check “Version” and
click “OK”. The version column appears. Check the
version of “ProDisc”.
The item at the upper left of the screen is displayed
according to the following order of priority.
Title >User-defined clip name >Standard format clip name
Therefore, the display of this item changes as following,
depending on whether there is a title.
- When a title has been set as a clip name on this unit, for
clips recorded on this unit, the title is displayed.
- The user-defined name or standard format name is
displayed for clips without a title.
110
File Operations in File Access Mode (for Windows)
Check that a drive letter has been assigned to this unit.
(The drive letter will differ depending on the number
of other peripherals connected to the remote
computer.)
Making FAM connections
1
If there is a disc loaded in this unit, put the unit into the
following state.
2
Use Explorer to perform file operations on the disc
loaded in this unit.
• Recording, playback, search and other disc
• Disc access by Lock or Delecte All Clips, Format
Stopped
You can operate in the same way that you operate on
local drives and files on network computers.
Notes
• Unsaved current clip list: Save or clear
• If you power this unit off during an FAM
connection, the data transferred thus far is discarded.
• All file operations are not possible for some types of
files.
2
3
If this unit is connected to a remote computer by FTP,
Connect the (i.LINK) S400connector on this unit to
the i.LINK (IEEE1394) connector on the remote
computer, using an i.LINK cable (see connections
For details, see “File operation restrictions”
To eject discs from a remote computer
Right click the icon representing this unit in Explorer, and
select “Eject” from the menu which appears.
Windows recognizes this unit as a removable disc, and
displays one of the following icons on the remote
computer’s task bar:
• Windows XP:
Exiting file operations
• Windows Vista:
Note
The remote computer is now able to perform file
operations when a disc is inserted into this unit.
Do not disconnect the cable before performing steps 1 to 3.
Note
1
Do one of the following on the
or
icon
You will not be able to log in if you put the unit into
the state described in step 1 after connecting the cable.
To log in, disconnect the cable, put the unit into the
state described in step 1, and connect it again.
displayed in the remote computer’s taskbar.
• Double click.
• Right click, and select the “Safely Remove
Hardware”.
When you make your first FAM connection
The Found New Hardware Wizard dialog appears when
you connect this unit to your computer. Select “Install the
software automatically (Recommended)”, and then click
the Next button. Click the Finish button when the software
installation finishes.
The “Safely Remove Hardware” dialog appears.
2
3
Select “Sony XDCAM PDW-****** IEEE 1394
SBP2 Device” (******: “F1600” or “HD1500”) and
click “Stop”.
Operation limitations during FAM connections
• Front panel operations are disabled, except for
operations with the EJECT button.
• This unit cannot be controlled from devices connected to
the REMOTE(9P) connector (D-sub 9-pin) and
(i.LINK) S400 connector.
The “Stop a Hardware device” dialog appears.
Select “Sony XDCAM PDW-****** IEEE 1394
SBP2 Device” (******: “F1600” or “HD1500”) and
click “OK”.
• Windows XP: “Sony XDCAM PDW-****** IEEE
1394 SBP2 Device” (******: “F1600” or
“HD1500”) is deleted from the “Hardware devices”
list.
• Signal input to this unit and signal output from this unit
are stopped.
• Windows Vista: A message appears to inform you
that you can now safely remove the device from
your computer.
Operating on files
1
Start Explorer.
111
File Operations in File Access Mode (for Windows)
This unit can now resume normal operations. (The
limitations described in “Operation limitations during
FAM connections” no longer apply.)
File Operations in File
Access Mode (for
Macintosh)
4
Disconnect the i.LINK cable as required.
To reconnect
To reconnect after exiting file operations, do one of the
following, depending on whether an i.LINK cable is
connected.
i.LINK cable is not connected: Connect this unit and a
remote computer with an i.LINK cable.
i.LINK cable is connected: Disconnect the i.LINK cable
from either this unit or the remote computer, wait for
at least 10 seconds, and then reconnect the
disconnected cable.
File access mode operating environment
Operating system requirements for file operations by file
access mode are as follows.
• Computer operating system: Mac OS X v10.4.11 or
higher
Preparations
Do the following on the remote computer and this unit.
• Install the FAM driver on the remote computer (see the
next item).
The unit is powered off and an i.LINK cable is
connected: Power the unit on.
You can enable and disable FAM connection from the
To install the FAM driver
Insert the supplied CD-ROM (XDCAM Application
Software) into the CD-ROM drive of your computer, and
execute the dmg file in FAM Driver >Mac >FAM Driver,
then follow the installation instructions.
For details, refer to the ReadMe file contained on the
CD-ROM disc.
To check the FAM driver version
Connect this unit to your computer with an i.LINK cable,
and then, with a disc loaded, start the system profiler utility
of the application. The version appears to the right of
“prodisk_fs” when you select “Advanced Functions”
under “Software”.
Making FAM connections
1
If there is a disc loaded in this unit, put the unit into the
following state.
• Recording, playback, search and other disc
• Disc access by clip deletion, disc formatting, etc.:
Stopped
• Unsaved current clip list: Save or clear
2
Connect the (i.LINK) S400 connector on this unit to
the i.LINK (IEEE1394) connector on the remote
When a disc is inserted into this unit, the remote
computer recognizes this unit as a removable disc. The
following icon appears in the Finder on the remote
112
File Operations in File Access Mode (for Macintosh)
computer, indicating that the computer is now able to
perform file operations.
Note
Do not disconnect the cable before performing steps 1 and
2.
1
Eject the disc by clicking the eject button to the right
of the icon for this unit in the Finder, or by dragging
the icon for this unit from the Finder to the Trash.
Operation limitations during FAM
connections
2
Disconnect the i.LINK cable as required.
• With the exception of the EJECT button, recording
buttons and playback control buttons are disabled.
• Do not use the EJECT button to eject discs. Always eject
discs from the computer.
• Do not disconnect the i.LINK cable during a FAM
connection. Doing so may result in unstable operation.
Always eject any loaded disc before disconnecting the
i.LINK cable.
To make a reconnection
To reconnect after exiting file operations, do one of the
following, depending on whether an i.LINK cable is
connected.
i.LINK cable is not connected: Connect this unit and a
remote computer with an i.LINK cable.
i.LINK cable is connected: The unit is mounted
automatically, so you do not need to do anything.
The unit is powered off and an i.LINK cable is
connected: Power the unit on.
Operating on files
You can enable and disable FAM connection from the
Proceed as follows.
1
2
Start the Finder.
Check to be sure that a drive has been assigned to this
unit.
Operate from the Finder on the files on the disc in this
unit.
You can operate in the same way that you operate on
local drives and files on network computers.
Notes
• If you power this unit off during a FAM connection, the
data transferred thus far is discarded.
• All file operations are not possible for some types of
files.
To eject discs from a remote computer
Click the eject button to the right of the icon for this unit in
the Finder, or drag the icon for this unit from the Finder to
the Trash.
Exiting file operations
Proceed as follows.
113
File Operations in File Access Mode (for Macintosh)
Note
FTP File Operations
An FTP client that supports UTF-8 is required to use
Unicode characters other than ASCII characters.
Command prompt FTP commands do not support UTF-8.
File operations between this unit and a remote computer
can be carried out by the File Transfer Protocol (called
FTP below).
To log in
If this unit is connected to a remote computer with a FAM
connection, first exit file operations on the FAM
Preparations
1
Connect the network connectors of this unit and a
remote computer with a network cable (see
unit to the network to which the remote computer is
1
Load a disc into this unit and put the unit into the
following state.
• Recording, playback, search and other disc
• Disc access by Lock or Delete All Clips, Format
Stopped
2
Set the IP address and other network setting items for
this unit.
1)
For details, see “To change network settings”
Note
If network settings have already been made
Check the IP address of this unit.
Login is not possible unless a disc is loaded and the
unit is in the state described above.
2
3
Start the command prompt.
1) This unit is able to acquire an IP address automatically from a DHCP
server. It also supports an Auto-IP function to assign an IP address
automatically when access from this unit to the DHCP server times
out. You can check DHCP settings and the assigned IP address on
page M5:NETWORK of the maintenance menu.
Enter “ftp <SP> <IP address>”, and press the Enter
key. (<SP> refers to a space.)
For example, if the IP address of this unit is set to
“192.168.001.010”, enter “ftp 192.168.1.10”.
Note
Refer to the Windows help for more information about
the FTP command.
If this unit is directly connected to a computer running
Windows Vista with a network cable, change the
setting as follows:
(1) Open “Network and Sharing Center” >“Manage
network connections” >“Local Area Connection” in
the control panel. (2) In the “Local Area Connection
Properties”, uncheck the “Internet Protocol Version 6
(TCP/IPv6)”, and then click the OK button.
If the connection succeeds, you are prompted to enter
a user name.
4
5
Enter the user name “admin” and press the Enter key.
When the user name is verified, you are prompted to
enter a password.
3
Enter the password and press the Enter key.
The password is set to the model name (“pdw-f1600”
or “pdw-hd1500”) when the unit is shipped from the
factory.
Making FTP connections
The login is complete when the password is verified.
FTP connections between this unit and a remote computer
can be made with either of the following.
• The command prompt
supported by this unit.
• FTP client software
If the connection times out
This section explains how to use the command prompt. For
more information about using FTP client software, refer to
the documentation of the FTP client software on your
system.
This unit terminates FTP connections if no command
is received within 90 seconds of the last command. If
this occurs, log out (see the next section) and repeat
steps 2 to 4.
114
FTP File Operations
Command syntax: PORT <SP> <h1,h2,h3,h4,p1,p2>
<CRLF>
Note
If you power this unit off during an FTP connection,
the data transferred thus far is discarded.
• h1 (most significant byte) to h4 (least significant byte): IP
address
• p1 (most significant byte), p2 (least significant byte): Port
address
To log out
Input example: PORT 10,0,0,1,242,48
To log out after finishing file operations, enter “QUIT” at
the command prompt and press the Enter key.
(IP address: 10.0.0.1, Port number: 62000)
PASV
Command list
This command requests this unit to “listen” on a data port
(which is not its default data port). (It puts this unit into
passive mode, waiting for the remote computer to make a
data connection.)
The FTP protocol commands supported by this unit
include standard commands (see the next section) and
Command syntax: PASV <CRLF>
Notes
TYPE
• To execute FTP commands, you must install application
software such as PDZ-1 on your computer.
• The commands supported by application software vary.
• An FTP client that supports UTF-8 is required to use
Unicode characters other than ASCII characters.
Command prompt FTP commands do not support
UTF-8.
Specifies the type of data to be transferred.
Command syntax: TYPE <SP> <type-code (options
delimited by <SP>)> <CRLF>
<type-code> can be any of the following. However, for
XDCAM, data is always transferred as “I”, regardless of
the type-code specification.
• A: ASCII
- N: Non-print
Standard commands
In the command syntax, <SP> means a space, entered by
pressing the space bar, and <CRLF> means a new line,
entered by pressing the Enter key.
- T: Telnet format
- C: ASA Carriage Control
• E: EBCDIC
- N: Non-print
USER
- T: Telnet format
Send this command to begin the login process.
Command syntax: USER <SP> <user name> <CRLF>
- C: ASA Carriage Control
• I: IMAGE (Binary) (default)
• L: LOCAL BYTE
- SIZE: byte size
Input example: USER admin
Input example: TYPE I
PASS
After sending the USER command, send this command to
complete the login process.
STRU
Command syntax: PASS <SP> <password> <CRLF>
Specifies the data structure.
Command syntax: STRU <SP> <structure-code>
<CRLF>
Input example: PASS pdw-hd1500
QUIT
<structure-code> can be any of the following. However,
for XDCAM, the structure is always “F”, regardless of the
structure-code specification.
Terminates the FTP connection. If a file is being
transferred, terminates after completion of the transfer.
Command syntax: QUIT <CRLF>
• F: File structure (default)
• R: Record structure
PORT
• P: Page structure
Specifies the IP address and port to which this unit should
connect for the next file transfer (for data transfer from this
unit).
Input example: STRU F
115
FTP File Operations
The wildcard characters “*” (any string) and “?” (any
character) may be used in <path-name>.
MODE
Specifies the transfer mode.
Command syntax: MODE <SP> <mode-code> <CRLF>
Input example 1: NLST-l
Input example 2: NLST Clip/*.MXF
<mode-code> can be any of the following. However, for
XDCAM, the mode is always “S”, regardless of the mode-
code specification.
RETR
Begins transfer of a copy of a file in the specified path on
this unit to the current directory on the remote computer.
• S: Stream mode (default)
• B: Block mode
Command syntax: RETR <SP> <path-name> <CRLF>
• C: Compressed mode
Input example: RETR Clip/C0001.MXF
Input example: MODE S
STOR
LIST
Begins transfer of a copy of a file in the specified path on
the remote computer to the current directory on this unit.
Depending on the type of file transferred, the following
files are created.
Sends a list of files from this unit to the remote computer.
Command syntax: LIST <SP> <options> <SP> <path-
name> <CRLF>
1)
• C*.MXF file
<options> can be any of the following.
• -a: Also display file names that begin with “.”
• -F: Append “/” to directory names.
-C*M01.XML file (metadata)
-C*M02.KLV file (user metadata)
-C*S01.MXF file (proxy AV data)
2)
• E*E01.SMI file
The following data is transferred, depending on whether
<path-name> specifies a directory or file.
• Directory specified: A list of the files in the specified
directory
-E*M01.XML file (metadata)
1) *: 0001 to 9999
2) *: 0001 to 0099
• File specified: Information about the specified file
• No specification: A list of the files in the current directory
The wildcard characters “*” (any string) and “?” (any
character) may be used in <path-name>.
Notes
• For C*.MXF files, the UMID of the copy source file is
not saved. However, it is saved if an immediately
preceding SITE UMMD extended command has been
issued.
• For C*.MXF files, some data, such as file header
metadata, may be missing.
Input example 1: LIST-a Clip
Input example 2: LIST Clip/*.MXF
NLST
• Depending on the transfer destination directory and the
file type, transfer may not be possible.
Sends a list of file names from this unit to the remote
computer, with no other information.
Command syntax: NLST <SP> <options or path-name>
<CRLF>
Command syntax: STOR <SP> <path-name> <CRLF>
Input example: STOR Edit/E0001E01.SMI
The following options may be specified when no path-
name is specified.
• -a: Also display file names that begin with “.”.
RNFR
RNTO
• -l: Display information other than file name (gives the same
result as the LIST command).
Rename a file.
• -F: Append “/” to directory names.
Specify the file to be renamed with the RNFR command,
and specify the new name with the RNTO command.
(Always follow a RNFR command with a RNTO
command.)
The following data is transferred, depending on whether
<path-name> specifies a directory or file.
• Directory specified: A list of the file names only in the
specified directory
• No specification: A list of the file names only in the current
directory.
116
FTP File Operations
Command syntax: RNFR <SP> <path-name (before
change)> <CRLF>
HELP
Displays a list of the commands supported by this unit, or
an explanation of the specified command.
RNTO <SP> <path-name (after change)> <CRLF>
Input example: RNFR General/info.txt
Command syntax: HELP <SP> <command-name>
<CRLF>
RNTO General/clip_info.txt
The following data is transferred, depending on whether a
command name is specified with <command-name>.
• Command name specified: Explanation of the specified
command.
DELE
Deletes the specified file on this unit.
Note
• No specification: Command list
Depending on the directory and file type, deletion may not
be possible.
Input example: HELP RETR
NOOP
Does nothing except return a response. (Used to check
whether this unit is running.)
Command syntax: DELE <SP> <path-name> <CRLF>
Command syntax: NOOP <CRLF>
Input example: DELE Clip/C0099.MXF
PWD
STAT
Displays the current directory (“/” if the directory is the
root directory).
Sends information about properties of the specified file, or
about data transfer status, from this unit to the remote
computer.
Command syntax: PWD <CRLF>
The following property information is sent, depending on
the file type.
CWD
• MXF file
Changes the current directory (moves from the current
directory to another directory).
- File name
- File type
Command syntax: CWD <SP> <path-name> <CRLF>
- CODEC type
- Frame rate
- Number of audio channels
- Duration
Moves to a directory as follows, depending on whether a
directory is specified with <path-name>.
• Directory specified: To the specified directory
• No specification: To the root directory
- UMID
• non-MXF file
- File name
Input example: CWD General
Command syntax: STAT <SP> <path-name> <CRLF>
CDUP
Moves one level up in the directory structure (makes the
parent of the current directory be the current directory).
The following data is transferred, depending on whether a
file is specified with <path-name>.
• File specified: The properties of the specified file
Command syntax: CDUP <CRLF>
• No specification: The size of the data transferred thus far
(unit: bytes)
MKD
Input example: STAT Clip/C0001.MXF
Creates a new directory.
ABOR
Note
Requests this unit to abort a file transfer currently in
progress.
Directories can be created only in the General directory.
Command syntax: ABOR <CRLF>
Command syntax: MKD <SP> <path-name> <CRLF>
SYST
Displays the system name of this unit.
Command syntax: SYST <CRLF>
117
FTP File Operations
Input example: SITE REPF Clip/C0001.MXF 5 150
(Transfer C0001.MXF. Body data is transferred only
from frame 6 to frame 150.)
RMD
Deletes a directory.
Note
SITE REPFL
Directories can be deleted only in the General directory.
Sends an MXF file from the specified path on this unit to
the remote computer. This command allows you to specify
a segment in the body of the MXF file (composed of video
and audio data), for transfer of the required segment only.
Command syntax: RMD <SP> <path-name> <CRLF>
Note
MDTM
A segment greater than the file size cannot be specified.
Command syntax: SITE REPFL <SP> “<path-name>”
<SP> <start-frame> <SP> <transfer-size> <CRLF>
Acquires the date and time of the most recent modification
of the file in the format “YYYYMMDDhhmmss” (YYYY:
year, MM: month, DD: day, hh: hour, mm: minute, ss:
second).
<path-name> specifies the path name of the file to transfer.
Enclose the path name in double quotation marks.
<start-frame> specifies an offset from the start of the file.
Data is transferred from the video frame at the offset (the
first frame is 0).
Note
The date and time cannot be acquired in the following
cases.
• When the path name includes a wildcard (“*”, replaced
by any string of characters, or “?”, replaced by any single
character).
• When the size of the path name is greater than 1023
bytes.
<transfer-size> specifies the number of video frames to
transfer (specify 0 to transfer to the end of the file).
Input example: SITE REPFL “Clip/sakura 0001.MXF” 5 150
(Transfer sakura 0001.MXF. Body data is transferred
only from frame 6 to frame 150.)
Command syntax: MDTM <SP> <path-name> <CRLF>
Input example: MDTM PROAV/DISCMETA.XML
SITE FSTS
Acquires the system status of this unit.
One of the following status codes is sent.
• 0: Initial state, or no disc is loaded.
• 1: File system mount is OK.
Extended commands
In the Command syntax, <SP> means a space, entered by
pressing the space bar, and <CRLF> means a new line,
entered by pressing the Enter key.
• 3: File system mount is not OK.
Command syntax: SITE FSTS <CRLF>
SITE REPF
SITE MEID
Sends an MXF file from the specified path on this unit to
the remote computer. This command allows you to specify
a segment in the body of the MXF file (composed of video
and audio data), for transfer of the required segment only.
Acquires the media ID of the disc loaded in this unit.
Command syntax: SITE MEID <CRLF>
SITE FUNC
Notes
Acquires the function and version of the extended
commands.
Information is sent in the following format.
• A segment greater than the file size cannot be specified.
• This command cannot be used when the path names
contains a space. Use the SITE REPFL command
instead.
Command syntax: <main function> <SP> <branch
function> <SP> <branch function version>
Command syntax: SITE REPF <SP> <path-name> <SP>
<start-frame> <SP> <transfer-size> <CRLF>
For XDCAM, sent in a format like “200 MXF DISK 1”
(“200” is a response code).
<start-frame> specifies an offset from the start of the file.
Data is transferred from the video frame at the offset (the
first frame is 0).
Command syntax: SITE FUNC <CRLF>
<transfer-size> specifies the number of video frames to
transfer (specify 0 to transfer to the end of the file).
118
FTP File Operations
Input example: SITE TCPR 00050001
SITE UMMD
(The starting timecode is preset to 01:00:05:00.)
When a C*.MXF file is sent with the STOR command, the
copy source UMID is saved if this command is invoked
immediately before the STOR command.
Command syntax: SITE UMMD <CRLF>
SITE DF
Acquires the amount of free disc space.
Command syntax: SITE DF <CRLF>
SITE CHMOD
Locks and unlocks clips. Also sets permissions for
directories and files in the General directory.
Command syntax: SITE CHMOD <SP> <flag> <SP>
<path-name> <CRLF>
Specify one of the following values in <flag>, according to
the specification in <path-name>.
• When a clip is specified in <path-name>
- 444: Lock.
- 666: Unlock.
• When a directory in the General directory is specified in
<path-name>
- 555: Forbid writing to the directory.
- 777: Allow writing to the directory.
• When a file in the General directory is specified in <path-
name>
- 444: Forbid writing to and execution of the file.
- 555: Forbid writing to the file, but allow execution.
- 666: Allow writing to the file, but forbid execution.
- 777: Allow writing to and execution of the file.
Input example: SITE CHMOD 444 Clip/C0001.MXF
(Lock clip C0001.MXF)
SITE TCPR
Presets the starting timecode of a clip copied with the
STOR command. Specify the timecode in the format
“ffssmmhh” (ff: frames, ss: seconds, mm: minutes, hh:
hours).
Notes
• This command remains in effect until a STOR command
is executed, or (if no STOR command is executed) until
the FTP connection is terminated.
• If a SITE UMMD command is executed after this
command, the SITE UMMD command takes priority
and this command is discarded.
• If this command is executed several times in sequence,
the last command takes priority.
Command syntax: SITE TCPR <SP> <timecode >
<CRLF>
119
FTP File Operations
Recording Continuous
Timecode with FAM and
FTP Connections
When you are connected to the unit by FAM or FTP, you
can create new clips with timecode that is continuous with
the timecode of the last frame of the last clip on the disc.
To record continuous timecode, set TCG on page P5 TC of
the function menu to “INT”, and set PRST/RGN to “TC”.
Then proceed as follows.
Note
Continuous timecode cannot be recorded if PRST/RGN on
page P5 TC of the function menu is set to “VITC”.
information.
FAM connection
Write clip files to the unit from the computer or other
device that is connected to this unit.
FTP connection
Use the “STOR” command to transfer clip files from the
computer that is connected to this unit.
If you issue the “SITE UMMD” command immediately
before the “STOR” command, the original timecode of the
transferred file is recorded, regardless of the setting of
TCG on page P5 TC of the function menu.
120
Recording Continuous Timecode with FAM and FTP Connections
Menus
7
Chapter
Menu System
Configuration
Setup Menu
The setup menu system of this unit comprises the basic
setup menu and extended setup menu.
The settings for this unit use the following menus.
Basic menu
Setup menu
The setup menu system of this unit comprises the basic
setup menu and extended setup menu.
This menu is used to make settings relating, for example,
to the following.
- the digital hours meter
- the preroll time
Maintenance menu
- the text information superimposed on the video output
to the monitor
- the menu banks for retaining menu settings
This provides audio control, and network and setup menu
settings, and also shows version information.
Extended menu
This menu is used to make a wide range of settings
relating to the functions of this unit, for example, the
control panel functions, video and audio control, and
digital data processing.
Function menu
For details, see “Basic Operations of the Function Menu”
Configuration of the basic menu
The basic menu comprises the following groups of items.
Disc Menu
For details, see “Disc Operations” (page 92).
Item group
Function
Refer to
Items
H01 to H17
Display of the total number of
hours the unit has been
powered on, and other
information collected by the
digital hours meter
Items
001 to 099
time, superimposed text
information, switching between
59.94i/59.94P/29.97P and 50i/
50P/25P/23.98P modes, etc.
Items
B01 to B20
Settings relating to the menu
banks for saving menu settings
Configuration of the extended menu
The extended menu comprises the following groups of
items.
121
Menu System Configuration / Setup Menu
Item group
Function
Refer to
Item group
Function
Refer to
Items
600 to 650
Settings relating to the
timecode generator
Items
100 to 199
Settings relating to control
panels
Items
651 to 699
Settings relating to the
metadata and UMID
Items
200 to 299
control interface
Items
700 to 799
Settings relating to video
control
Items
300 to 399
Settings relating to editing
operations
Items
800 to 899
Settings relating to audio
control
Items
400 to 499
Settings relating to preroll
Items
900 to 999
Settings relating to digital
processing
Items
500 to 599
Settings relating to disc
protection
Items in the basic menu
The basic menu items (excluding the items related to the
digital hours meter) are listed in the following table.
connector, or the HDSDI OUTPUT 2 (SUPER)
connector.
• An abbreviated name appears in the time data display
area when you press the NEXT button.
• Item names are the names which appear on the video
monitor screen of this unit and an external monitor,
when the input signals to the monitor are the video
signals output from the COMPOSITE OUTPUT 2
(SUPER) connector, the SDSDI OUTPUT 2 (SUPER)
• The values in the Settings column are the values which
appear in the time data display area. (The values may
appear in a different format on an external monitor. In
this case, the external monitor values are shown in
parentheses.) Underlined values are the factory defaults.
Item number Item name
Settings
001
002
PREROLL TIME
0 s (0 sec)... 5 s (5 sec)... 30 s (30 sec): Set the preroll time to between 0
and 30 seconds in steps of 1 second.
A preroll time of at least 5 seconds is recommended when using this
unit for editing.
CHARACTER H-POSITION
Adjust the horizontal screen position (as a hexadecimal value) of the text
information output from the COMPOSITE OUTPUT 2 (SUPER) connector,
the SDSDI OUTPUT 2 (SUPER) connector, or the HDSDI OUTPUT 2
(SUPER) connector for superimposed display on the monitor. The
hexadecimal value 00 is for the far left of the screen. Increasing the value
moves the position of the characters to the right.
00 ... 0C ... 28 (When the number of system lines is 1080 and the
system frequency is 59.94i, 29.97P, 50i, 25P, or 23.98P.)
00 ... 0B ... 28 (When the number of system lines is 720 and the system
frequency is 59.94P or 50P.)
Set this item by adjusting to the required position while viewing the monitor.
003
CHARACTER V-POSITION
Adjust the vertical screen position (as a hexadecimal value) of the text
information output from the COMPOSITE OUTPUT 2 (SUPER) connector,
the SDSDI OUTPUT 2 (SUPER) connector, or the HDSDI OUTPUT 2
(SUPER) connector for superimposed display on the monitor. The
hexadecimal value 00 is for the top of the screen. Increasing the value
lowers the position of the characters.
00 ... 2A ... 32 (When the number of system lines is 1080 and the
system frequency is 59.94i, 29.97P, 50i, 25P, or 23.98P.)
00 ... 29 ... 32 (When the number of system lines is 720 and the system
frequency is 59.94P or 50P.)
Set this item by adjusting to the required position while viewing the monitor.
122
Setup Menu
Item number Item name
005 DISPLAY INFORMATION
Settings
Determine the kind of text information to be output from the COMPOSITE
OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2 (SUPER) connector,
or the HDSDI OUTPUT 2 (SUPER) connector.
SELECT
T&sta (time data & status): Time data and the units status.
T&UB (time data & UB): Time data and user bits data. (When UB (user bits
data) is selected with CNTR SEL on the HOME page of the function
menu, the user bits data and time data arranged in that order are
displayed.)
T&CNT (time data & CNT): Time data and counter count. (When
COUNTER is selected with CNTR SEL on the HOME page of the
function menu, the counter count and time data arranged in that order
are displayed.)
T&T (time data & timecode): Time data and timecode (TC or VITC)
T&clp (time data & clip no): Time data and clip number
time (time data only): Time data only
006
LOCAL FUNCTION ENABLE
Determine which recording and playback control buttons on the front panel
are enabled when this unit is controlled from external equipment.
dis (all disable): All buttons and switches are disabled.
st&ej (stop & eject): Only the STOP button and EJECT button are enabled.
ena (all enable): All buttons and switches are enabled.
007
009
DISC TIMER DISPLAY
CHARACTER TYPE
Determine whether to display the counter in 12-hour mode or 24-hour mode.
+ –12H (+/–12H): 12-hour mode
24H: 24-hour mode
Determine the type of characters such as timecode output from the
COMPOSITE OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2
(SUPER) connector, or the HDSDI OUTPUT 2 (SUPER) connector for
superimposed display on the monitor.
white: White letters on a black background
black: Black letters on a white background
W/out: White letters with black outline
B/out: Black letters with white outline
Set this item by selecting the required type while viewing the monitor.
011
012
CHARACTER V-SIZE
Determine the vertical size of characters such as timecode output from the
COMPOSITE OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2
(SUPER) connector, or the HDSDI OUTPUT 2 (SUPER) connector for
superimposed display on the monitor.
×1
:Standard size
×2 :2 times standard size
Set this item by selecting the required size while viewing the monitor.
CONDITION DISPLAY ON
VIDEO MONITOR
Select whether to display disc condition marks in external monitor output
(output from the COMPOSITE OUTPUT 2 (SUPER) connector, the SDSDI
OUTPUT 2 (SUPER) connector, or the HDSDI OUTPUT 2 (SUPER)
connector).
dis (disable): Do not display.
ena (enable): Display.
123
Setup Menu
Item number Item name
Settings
013
SYSTEM FREQUENCY
SELECT MENU
Specify whether to enable switching the system frequencies (59.94i, 59.94P,
29.97P, 50i, 50P, 25P, 23.98P).
off: Do not enable switching the system frequencies.
on: Enable switching the system frequencies.
Note
Settings for both basic and extended menu items are saved separately for
different system frequencies.
• 1080 59.94i/29.97P
• 1080 50i/25P
• 1080 23.98P
• 720 59.94P
• 720 50P
Therefore, when you switch system frequencies, all menu items are reset to
the current settings for the new mode. (They are different from the setting for
the previous mode.)
016
017
ALARM DISPLAY
Select whether to display alarm messages.
off: Do not display alarm messages. (However, certain important alarms are
displayed.)
limit (on (limited)): Display only a minimum number of alarm messages.
on: Display all alarm messages.
For details about alarm message display conditions, see “Alarms”
SUB STATUS DISPLAY SELECT Determine the kind of sub status information to be output from the
COMPOSITE OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2
(SUPER) connector, or the HDSDI OUTPUT 2 (SUPER) connector.
off: Do not output sub status information.
rmain (disc remain): Available disc space (unit: minute)
clip (clip no): Order of playback of the selected clip/total number of clips
pbr (playback remain): The remaining playback time of the selected clip
from the current playback position (hours:minutes:seconds:frames).
a)
edit (edit preset): Edit preset state
a)
ed&tc (edit preset & tc mode): Edit preset state and settings of timecode
Note
When menu item 005 is set to “off”, sub status information is not displayed
when this item is set to anything other than “off”.
024
MENU CHARACTER TYPE
Determine the type of characters in menu text output from the COMPOSITE
OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2 (SUPER) connector,
or the HDSDI OUTPUT 2 (SUPER) connector for superimposed display on
the monitor.
white: White letters on a black background.
black: Black letters on a white background.
W/out: White letters with black outline.
B/out: Black letters with white outline.
Set this item by selecting the required type while viewing the monitor.
028
029
HD CHARACTER
Specify whether to superimpose text information on the video signal output
from the HDSDI OUTPUT 2 (SUPER) connector.
off: Do not superimpose.
f-key: Follow the function menu setting.
STORED OWNERSHIP
Specify whether to enable changing UMID ownership information settings
(COUNTRY, ORGANIZATION and USER).
off: Do not enable.
on: Enable.
124
Setup Menu
Item number Item name
Settings
031
RECORDING FORMAT
Set the recording format.
HD422: HD422
420HQ: HD420HQ
420SP: HD420SP
b)
b)
b)
IMX50(IMX50Mbps): MPEG IMX 50 Mbps
IMX40(IMX40Mbps): MPEG IMX 40 Mbps
IMX30(IMX30Mbps): MPEG IMX 30 Mbps
b)
DVCAM: DVCAM
033
034
BATTERY END VOLTAGE
Sets the voltage to shut down the unit in the battery operation. The battery
near end indicator flashes at +0.7 V of the set voltage.
10.5V to 13.5V: 10.5 V to 13.5 V in 0.5 V unit.
MENU STATUS DISPLAY ON
Specify whether to display the setup menu status at the left edge of the
status display line when setup menu item 005 “DISPLAY INFORMATION
SELECT” is set to “T&sta”.
a)
VIDEO MONITOR
dis (disable): Do not display.
ena (enable): Display. (The display is visible only when no disc is loaded,
and during insertion and ejection of a disc.)
035
CLIP TITLE NAMING SELECT
Sub-item
Specify whether to allow user definition of the titles assigned to clips.
off: Do not allow assignment.
on: Allow assignment.
about assigning titles.
1
TITLE
Specify whether to assign titles to recorded clips.
disable: Do not assign titles to clips.
enable: Assign titles to clips.
2
PREFIX
Set the prefix of the title (up to 10 characters). The allowable characters are
alphanumeric characters, symbols (! # $ % & ' ( ) + , - . ; = @ [ ] ^ _ { } ~), and
the space character.
TITLE
3
NUMERIC
Set the initial value of the numeric part of the title (00001 to 99999, five-digit
number).
00001
036
FILE NAMING
Specify whether to allow use of clip and clip list files with user-defined
names.
how to make the settings.
Sub-item
1
2
NAMING FORM
Specify the clip and clip list naming format. (Specify whether to allow use of
files with user-defined names.)
C****: Standard format (Do not allow use of files with user-defined names)
free: Free format (Allow use of files with user-defined names)
AUTO NAMING
When “free” is selected under the sub-item “NAMING FORM”, specify the
format of the names of clips recorded on this unit. Specify the standard
name format, or the same name as the title listed below, or the name
specified in planning metadata.
C****: Use the standard format for clip names.
title: Use the title set in setup menu item 035 “CLIP TITLE NAMING
SELECT” for clip names.
plan: Use the name specified in planning metadata.
B01
B02
B03
B11
B12
B13
RECALL SETUP BANK-1
RECALL SETUP BANK-2
RECALL SETUP BANK-3
SAVE SETUP BANK-1
SAVE SETUP BANK-2
SAVE SETUP BANK-3
Set to “on” to recall menu settings from menu bank 1.
Set to “on” to recall menu settings from menu bank 2.
Set to “on” to recall menu settings from menu bank 3.
Set to “on” to save current menu settings to menu bank 1.
Set to “on” to save current menu settings to menu bank 2.
Set to “on” to save current menu settings to menu bank 3.
125
Setup Menu
Item number Item name
Settings
B20
RESET SETUP MENU
Set to “on” to return the settings of the current menu to the factory default
settings. Set to “bank-4” to set the current menu to the settings saved in
menu bank 4.
off:
on: Return the current menu to the factory default settings.
bank-4: Set the current menu to the settings saved in menu bank 4.
a) PDW-F1600 only
b) HD1500 When the PDBK-S1500 or PDBK-F1500 option is installed.
connector, or HDSDI OUTPUT 2 (SUPER) connector on
this unit, and press the MENU button.
To display menus in the time data display area
Press the MENU button to display a setup menu on the
video monitor display, and press the DISPLAY button.
The video monitor display is switched the basic operation
display, and the number and setting of the currently
selected menu item appear in the time data display area.
Basic menu operations
The setup menus are displayed in the time data display area
of the basic operation display or on the video monitor
display. If you have connected an external monitor, they
are also superimposed over the picture shown on that
monitor.
To display the setup menu
H01: 000109
Item number (flashing)
Setting
To display the full item name
Hold down the NEXT button.
Buttons used to change settings
Use the following buttons to change setup menu settings.
Menu control
buttons
Functions
MENU button
• Displays and hides the setup and user
interface menus.
• Returns to the menu from a setting
screen.
DISPLAY button
MENU button
Time data display area
Press the MENU button.
A setup menu appears on the video monitor display, and a
cursor “*” indicates the currently selected menu item.
PUSH
SET(S.SEL) knob
• When turned clockwise or
counterclockwise, moves the “*” mark
up or down in the list of menu items to
select the item to change.
• When turned clockwise or
counterclockwise, changes a menu
item setting.
Cursor indicating the currently selected item
Group name for the currently selected item
• When pressed, answers “Yes” to a
question.
Function buttons RETURN: Goes up one level.
HOUR METER
*HO1:OPE HOURS
-
H11:OPE HOURS r-
102
102
F1 to F6
SELECT: Selects an item.
UP: Skips back 100 or 50 items in the
list of menu items.
(The function to
be displayed
I
I
I
I
I
I
I
varies depending DOWN: Skips forward 100 or 50 items in
on the situations.)
the list of menu items.
SAVE: Saves a new setting to memory.
EXIT: Exits the current menu.
–: Changes a setting.
+: Changes a setting.
RESET/RETURN • Returns the current setting to the
button
factory default.
• Answers “No” to a question.
To display menus on the external monitor
Connect the monitor to the COMPOSITE OUTPUT 2
(SUPER) connector, SDSDI OUTPUT 2 (SUPER)
126
Setup Menu
video monitor display and the time data display area
return to their normal indications.
To change the settings of menu items
Proceed as follows to change the settings of menu items.
Notes
1
Use the PUSH SET(S.SEL) knob to select the required
item.
• If you power off the unit before a save operation is
completed, settings may be lost. Wait until the save is
completed before powering off the unit.
Example: Screen display when item 005 DISPLAY
INFORMATION SELECT is selected
• If, instead of pressing the SAVE function button (F5),
you press the MENU button, the new settings are not
saved. The message “ABORT !” appears on the video
monitor display and “Abort !” in the time data display
area for about 0.5 seconds, and the system exits the
menus. To change more than one setting, be sure to press
the SAVE function button (F5) after making the settings.
Current setting
KEY PARAMETER
0O1:P-ROLL TIME -
002:CHARA H-POS -
003:CHARA V-POS -
5 s
0A
2E
*005:DISPLAY SEL - T&CNT
006:LOCAL ENA - st&ej
007:DISC TIMER - +-12H
009:CHARA TYPE - white
011:CHARA SIZE -
012:COND DISPLY -
013:SYSTEM FREQ -
x1
dis
off
on
To return menu settings to their factory
default settings
016:ALARM
-
After changing menu settings, use the following procedure
to return the settings to their factory default settings
(setting initialization).
2
Press the PUSH SET(S.SEL) knob or the SELECT
function button (F2).
To return a particular setting to its factory default
setting
In the screen that selects the setting of that item, press the
RESET/RETURN button.
For example, proceed as follows to return the 005
DISPLAY INFORMATION SELECT item to its default
setting. This assumes that the setting has been changed
from the factory default “time data & status” in step 3 of
the procedure in “To change the settings of menu items”
This displays the setting screen 2 for the menu item
selected in step 1.
Example: Setting screen display when item 005
DISPLAY INFORMATION SELECT is selected
ITEM-005
DISPLAY INFORMATION
SELECT
time data & CNT
1
Press the RESET/RETURN button.
“time data & status” (factory default setting) is
selected.
Current setting
2
Press the SAVE function button (F5).
3
Use the PUSH SET(S.SEL) knob or the +/– function
button (F3 or F4) to change the setting.
The setting returned to its factory default is saved in
memory as the current setting.
Turning the PUSH SET(S.SEL) knob while holding
down the SHIFT button increases the increment of
adjustment.
To return all settings to their factory default
settings
1
2
Press the MENU button to display the setup menu.
Press the RESET/RETURN button.
4
5
To change other settings, press the PUSH SET(S.SEL)
knob or the SELECT function button (F2) to return to
the previous screen, then repeat steps 1 to 3.
A message appears, to confirm whether you wish to
return all settings to their factory default settings.
When you have completed the settings, press the
SAVE function button (F5).
Message on the video
monitor display
Initialize all items to factory
preset values?
The message “NOW SAVING...” appears on the video
monitor display, and “Saving...” appears in the time
data display area, while the new settings are saved in
memory. When the saving operation is completed, the
Message in the time data Init setup?
display area
127
Setup Menu
3
Press the SAVE function button (F5).
You can press the UP function button (F3) or the
DOWN function button (F4) to move the “*” mark by
100 menu items.
The message “NOW SAVING...” appears on the video
monitor display, and “Saving...” appears in the time data
display area, while the settings of all items are returned to
their factory default settings. These factory default settings
are saved in memory. If you power off the unit while
settings are being saved, settings may not be correctly
returned to their factory default settings. Wait until the
saving is completed before powering off the unit.
4
Press the PUSH SET(S.SEL) knob.
A setting screen for the currently selected item
appears.
RETURN
CUSTOM ITEM-H13
To abandon the resetting operation
Instead of pressing the SAVE function button (F5), press
the RESET/RETURN button. The display returns to the
top level of the setup menu, leaving the settings
unchanged.
SEEK RUNNING HOURS 0
(resettable)
-
on
+
SAVE
EXIT
To customize the display of setup menu
items
You can select the menu items displayed in the setup
menu.
SETUP
5
6
Turn the PUSH SET(S.SEL) knob to select “on” or
“off”.
on: Display the item in the setup menu.
off: Do not display the item in the setup menu.
1
2
Set maintenance menu item M41: CUSTOMIZE to
“ENABLE”.
Press the PUSH SET(S.SEL) knob.
maintenance menu.
To continue selecting items
Repeat steps 3 to 6.
Hold down the MENU button for about three seconds.
The SETUP CUSTOMIZE screen appears.
To set items more quickly
In step 3, turn the PUSH SET(S.SEL) knob to move
the “*” mark, and then press the ON function button
(F1) or OFF function button (F2) to set items
continuously.
ON
SETUP CUSTOMIZE
*H01:OPE HOURS -
H02:LASER0
H03:LASER1
on
on
OFF
UP
-
-
on
on
H11:OPE HOURS r-
H13:SEEK HOURS0r-
H14:SPDL HOURS r-
H15:LOAD COUNT r-
H17:SEEK HOURS1r-
001:P-ROLL TIME -
002:CHARA H-POS -
003:CHARA V-POS -
off
off
off
off
off
off
off
7
Press the SAVE function button (F5).
DOWN
SAVE
EXIT
SETUP
Customization indication in the setup menu
When you open the setup menu after customizing the
displayed menu item, a “[C]” mark appears at the upper
right of the screen to indicate that the menu has been
customized.
3
Turn the PUSH SET(S.SEL) knob so that the “*” mark
appears next to the item you want to hide or display in
the setup menu.
ON
SETUP CUSTOMIZE
H01:OPE HOURS -
H02:LASER0
H03:LASER1
on
on
OFF
UP
-
-
on
on
H11:OPE HOURS r-
*H13:SEEK HOURS0r-
H14:SPDL HOURS r-
H15:LOAD COUNT r-
H17:SEEK HOURS1r-
001:P-ROLL TIME -
002:CHARA H-POS -
003:CHARA V-POS -
off
off
off
off
off
off
off
DOWN
SAVE
EXIT
SETUP
128
Setup Menu
Items in the extended menu
The following tables show the items in the extended menu.
• Item names are the names which appear on an external
monitor to which the output of the COMPOSITE
OUTPUT 2 (SUPER) connector, the SDSDI OUTPUT 2
(SUPER) connector, or the HDSDI OUTPUT 2
(SUPER) connector is input.
• The values in the Settings columns are the values which
appear in the time data display area. (The values may
appear in a different format on an external monitor. In
this case, the external monitor values are shown in
parentheses.) Underlined values are the factory defaults.
• An abbreviated name appears in the time data display
area when you press the NEXT button.
Menu items in the 100s, relating to the control panels
Settings
Item number Item name
101
105
107
108
SELECTION FOR SEARCH DIAL
ENABLE
Select how the unit enters the shuttle, jog, or variable speed mode.
dial (dial direct): Press the SHTL/JOG or VAR/JOG button or, except
during recording/editing, turn the jog dial or shuttle dial.
key (via search key): Press the SHTL/JOG or VAR/JOG button.
REFERENCE SYSTEM ALARM
Select whether to display a warning when the reference video signal is
not being supplied, or when it differs from this unit’s system frequency.
off: No warning.
on: Flash the STOP button as a warning.
REC INHIBIT LAMP FLASHING
AUTO EE SELECT
Select whether to flash the REC INHI indicator when recording is
off: Light the REC INHI indicator.
on: Flash the REC INHI indicator.
When a disc is inserted and PB/EE on the HOME page of the function
menu is set to “EE”, select the operation modes in which input video and
audio signals are automatically handled in E-E mode.
S/F/R (stop/f.fwd/f.rev): In stop/fast-forward/fast-reverse modes
stop: In stop mode
109
114
FORCED EE WHEN DISC UNLOAD During disc loading/unloading and when no disc is inserted, select
whether to control the output signal PB/EE setting.
on: Do not control (the signal is always an E-E signal).
off: Control.
AUDIO MONITOR OUTPUT LEVEL Select whether to control the level of the audio signal output from the
AUDIO MONITOR R, L connectors with the LEVEL knob for the
PHONES jack.
var (variable): Control.
fixed: Do not control.
118
KEY INHIBIT SWITCH EFFECTIVE Select which buttons can be operated when the KEY INHI switch is set to
AREA
“ON”. The following sub-items control different sets of buttons
independently.
Sub-item
1
FUNCTION-KEY
Select whether function buttons on the front panel are enabled.
dis (disable): Disabled.
ena (enable): Enabled.
2
CONTROL PANEL
Select operable buttons on the front panel are enabled.
dis (disable): Disabled.
ena (enable): Enabled.
119
121
130
VARIABLE SPEED LIMIT IN KEY
FRAME PB MODE
Select the playback speed range when carrying out playback in variable
speed mode from the front panel of this unit.
off (off (–2 to +2)): –2 to +2 times normal speed.
on (on ( 0 to +1)): 0 to +1 times normal speed.
Select the variable playback field/frame mode.
auto: Field playback
frame: Frame playback. Compared to field playback, frame playback
gives more detail during playback of still pictures.
DISPLAY DIMMER CONTROL
Set the brightness of the indication on the LCD.
10%, 25%, 50%, 75%, 100%
129
Setup Menu
Menu items in the 100s, relating to the control panels
Settings
Item number Item name
131
AUDIO VOLUME
Select whether each of the CH-1/ALL CH, CH-2 to CH-4 adjustment
knobs on the control panel is effective to control the audio recording level
and playback level on each channel or the CH-1/ALL CH adjustment
knob alone functions as a master control to control the audio level on all
channels together.
each: Each of the CH-1/ALL CH, CH-2 to CH-4 adjustment knobs is
effective to control each channel.
all: The CH-1/ALL CH adjustment knob alone functions as a master
control.
When “all” is selected, the ALL CH indicator under the CH-1/ALL CH
adjustment knob lights up.
140
142
AREA MARKER
REPEAT MODE
Select whether to display the display area of SD output on the color LCD.
off: Do not display.
on: Display.
Put the unit into repeat playback mode, or exit from repeat playback
mode.
off: Exits from repeat playback mode.
play: Puts the unit into repeat playback mode.
143
145
INDEX PICTURE POSITION
Select the frame of the clip to use as the thumbnail image (index picture)
when recording.
0sec to 10sec: Can be set in the range from 0 seconds (first frame of the
clip) to10 seconds, in units of 1 second.
MODE KEY ENABLE DURING
RECORDING
Select whether the STOP button is the only button that stops recording.
a)
ena (all enable): Recording stops when the EJECT button , PLAY
b)
button, STOP button, SHTL/JOG button, and VAR/JOG button are
pressed.
stop: Recording stops only when the STOP button is pressed.
150
151
REC MODE
Select the recording mode.
normal: Normal recording mode
D.EXC (disc exchange cache): Disc Exchange Cache mode
C.REC (clip continuous rec): Clip Continuous Rec mode
GUI OPERATION
Select whether to disable the display of the Thumbnail Menu and Disc
Menu when this unit is in any mode other than stop mode.
ena(enable): Do not disable.
stop(via stop): Enable the display of menus in the stop mode.
dis(disable): Disable.
153
154
FIND MODE
Specify the frame to be cued up when the PREV or NEXT button is
pressed.
clip: The first frame of the clip
R.ST (clip & rec start mark): The frame where a Rec Start essence
mark is set (if no essence mark is set, the first frame of the clip)
SINGLE CLIP PLAY MODE
Put the unit into single clip playback mode, or exit from single clip
playback mode.
off: Exits from single clip playback mode. (Puts the unit into continuous
playback mode.)
on: Puts the unit into single clip playback mode.
a) The disc is ejected after recording stops.
b) The unit enters stop mode when the PLAY button is pressed. It enters
freeze picture mode (jog, shuttle, or variable mode) when the SHTL/JOG
button or VAR/JOG button is pressed.
Menu items in the 200s, relating to the remote control interface
Item number Item name
Settings
201
PARA RUN
Select whether to use synchronized operation for two or more VTRs.
dis (disable): No synchronized operationena
ena (enable): Use synchronized operation
Note
To use synchronized operation for two or more VTRs, set item 201 to ena
on all of the VTRs.
130
Setup Menu
Menu items in the 200s, relating to the remote control interface
Settings
Item number Item name
212
VIDEO REMOTE CONTROL
Select whether to control the up converter or down converter when
a)
controlling the image enhancer from the HKDV-900 or another unit
connected to the VIDEO CONTROL connector.
down: Control the down-converter.
SELECT
up: Control the up-converter.
u&d: Control both the up- and down-converter.
Note
It is also possible to adjust setup menu item 718 SETUP LEVEL/BLACK
LEVEL from the HKDV-900. Hold down the D2 button on the HKDV-900
and rotate the SETUP dial.
214
REMOTE INTERFACE
When the remote control switch is set to REMOTE, select the device from
which to remote-control this unit.
9PIN: Device connected to the REMOTE(9P) connector.
SDI: Device connected to the SD/HDSDI INPUT connector.
i.LINK: Device connected to the (i.LINK) S400 connector.
b)
b)
215
257
i.LINK MODE
Select the connection method for the (i.LINK) S400 connector.
FAM (FAM (PC REMOTE)): FAM connection
TS: TS connection
NETWORK ENABLE
Select the remote control switch positions which enable network
connections.
net (network): Only when the switch is set to “NET”.
n&9P (network & remote(9PIN)): When the switch is set to “NET”, and
when the switch is set to “REMOTE” and setup menu item 214 is set
c)
to “9PIN”.
a) HD1500 When the PDBK-S1500 or PDBK-F1500 option is installed.
b) When the PDBK-201 option board is installed
connections, the device connected to the REMOTE(9P) connector cannot
be used to control this unit.
c) FTP connections can be made only when the device connected to the
REMOTE(9P) connector (D-sub 9 pin) is in stop mode. During FTP
Menu items in the 300s, relating to editing operations
Settings
Item number Item name
301
VAR SPEED RANGE FOR
SYNCHRONIZATION
Select the playback speed range when carrying out playback in variable
speed mode from a remote control unit connected to the REMOTE(9P)
connector.
–2~+2: –2 to +2 times normal speed.
wide: –2.20 to +2.20 times normal speed.
311
312
313
314
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH1
Select methods for setting the edit presets of the digital audio channels
CH1 to CH4 of this unit. Make these settings when using an editor (PVE-
500, BVE-600, etc.) or remote control unit without a function to control
digital audio edit presets.
The edit presets of the digital audio channels of this unit are turned on
and off according to the specified analog audio presets of the editor or
remote control unit.
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH2
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH3
nodef (no definition): No definition
ch 1 (analog ch1): Follow the edit preset of analog channel 1.
ch 2 (analog ch2): Follow the edit preset of analog channel 2.
ch1+2 (analog ch1+ch2): Follow the edit preset of analog channel 1 or
2.
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH4
(The default settings for each item are as follows)
311: ch 1 (analog ch1)
312: ch 2 (analog ch2)
313: nodef (no definition)
314: nodef (no definition)
131
Setup Menu
Menu items in the 300s, relating to editing operations
Settings
Item number Item name
317 [F1600]
AUDIO EDIT MODE
Select the type of audio transition used for linear editing.
cut edit: Cut editing (audio discontinuity at transition point, and possible
noise during playback).
cross fade: Cross-fade
320
DIGITAL AUDIO PB PROCESS ON Specify the handling of audio at edit points and at the second and
EDIT POINT
subsequent recording start points in Clip Continuous Rec recording.
cut: Carry out a cut (possibly resulting in audio discontinuities at the edit
point).
fade: Fade out and fade in.
329
330
331
332
344
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH5
Select methods for setting the edit presets of the digital audio channels
CH5 to CH8 of this unit. Make these settings when using an editor
(PVE-500, BVE-600, etc.) or remote control unit without a function to
control digital audio edit presets.
The edit presets of the digital audio channels of this unit are turned on
and off according to the specified analog audio presets of the editor or
remote control unit.
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH6
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH7
nodef (no definition): No definition
ch 1 (analog ch1): Follow the edit preset of analog channel 1.
ch 2 (analog ch2): Follow the edit preset of analog channel 2.
ch1+2 (analog ch1+ch2): Follow the edit preset of analog channel 1 or
2.
[F1600]
ANALOG AUDIO EDIT PRESET
REPLACE FOR CH8
ASSEMBLE AUTO EDIT
POSTROLL RECORDING
Set whether to record 2 seconds of postroll when an additional clip is
recorded by sending the AUTO EDIT command (9-pin protocol 20·42)
from a nonlinear editing system connected to the REMOTE(9P)
connector on the rear panel.
Note
When using a linear editing system, postroll will not be recorded
regardless of this setting.
off: Do not record postroll.
on: Records approximately 2 seconds of postroll.
Menu items in the 400s, relating to preroll
Settings
Item number Item name
401
FUNCTION MODE AFTER CUE-UP Select the state that the unit goes into after a cuing-up operation.
stop: Stops (the stop mode).
still: Still playback (in jog and shuttle mode).
Menu items in the 500s, relating to disc protection
Item number Item name
501 STILL TIMER
Settings
To protect the disc against shock and vibrations, and to lengthen the life
of the laser diodes, the unit automatically enters standby off mode
whenever a specified time elapses in a disc stop mode (stop mode or the
still picture mode of search mode). This allows you to set the time after
which the unit exits a disc stop mode and enters standby off mode.
0.5 s (0.5 sec)... 8 m (8 min)... 30 m (30 min): Can be set in the range
from 0.5 seconds to 30 minutes.
off: Do not put into standby off mode.
132
Setup Menu
Menu items in the 600s, relating to the timecode, metadata, and UMID
Settings
Item number Item name
601
VITC POSITION In 59.94i/59.94P/ Select the line into which to insert VITC signals (SD output)
b)
29.97P mode
12H ... 16H ... 20H: Any line from line 12 through line 20.
SEL-1
Notes
• You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
• In 59.94i/59.94P/29.97P/23.98P mode (J), output of wide picture
information is given priority if OUTPUT in setup menu item 731 is set to
“auto” and the VITC insertion line is set to line 16.
• In 59.94i/59.94P/29.97P/23.98P mode (UC), output of wide picture
information is given priority if OUTPUT in setup menu item 731 is set to
“auto” and the VITC insertion line is set to line 20.
In 50i/50P/25P
mode
Select the line into which to insert VITC signals (SD output)
9H ... 19H ... 22H: Any line from line 9 through line 22.
Note
You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
602
VITC POSITION In 59.94i/59.94P/ Select the line into which to insert VITC signals (SD output)
b)
29.97P mode
12H ... 18H ... 20H: Any line from line 12 through line 20.
SEL-2
Notes
• You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
• In 59.94i/59.94P/29.97P mode (J), output of wide picture information is
given priority if OUTPUT in setup menu item 731 is set to “auto” and the
VITC insertion line is set to line 16.
• In 59.94i/59.94P/29.97P mode (UC), output of wide picture information
is given priority if OUTPUT in setup menu item 731 is set to “auto” and
the VITC insertion line is set to line 20.
In 50i/50P/25P
mode
Select the line into which to insert VITC signals (SD output)
9H ... 21H ... 22H: Any line from line 9 through line 22.
Note
You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
605
607
TCG REGEN MODE
Select the signal to be regenerated when the timecode generator is in the
regeneration mode.
TC&UB: Both the timecode and user bits are regenerated.
TC: Only the timecode is regenerated.
UB: Only the user bits are regenerated.
U-BIT BINARY GROUP FLAG
Select the user bits to be used in the timecode generated by the
timecode generator.
000 (000:not specified): Character set not specified.
001 (001:iso character): 8-bit characters compliant with ISO 646 and
ISO 2022.
010 (010:unassigned-1): Undefined.
011 (011:unassigned-2): Undefined.
100 (100:unassigned-3): Undefined.
101 (101:page / line): SMPTE-262M page/line multiplex system.
110 (110:unassigned-4): Undefined.
111 (111:unassigned-5): Undefined.
133
Setup Menu
Menu items in the 600s, relating to the timecode, metadata, and UMID
Settings
Item number Item name
610 [F1600]
REGEN CONTROL MODE
Select whether or not the time code is automatically regenerated.
auto(assem & insert)edit: In automatic editing carried out in either
assemble mode or insert mode with this unit as the recorder,
regardless of the settings of F1 (TCG) and F2 (PRST/RGN) in
function menu page 5, the time code generator regenerates
according to the time code on the disc.
auto assemble edit: In automatic editing carried out in assemble mode
with this unit as the recorder, regardless of the settings of F1 (TCG)
and F2 (PRST/RGN) in function menu page 5, the time code
generator regenerates according to the time code on the disc.
manual: Regardless of whether this unit is the recorder or player, the
time code generator operates in accordance with the settings of F1
(TCG) and F2 (PRST/RGN) in function menu page 5.
assemble & insert: Whether local or remote and regardless of the
settings of F1 (TCG) and F2 (PRST/RGN) in function menu page 5,
the time code generator regenerates according to the time code
played back from the disc.
611
TC OUTPUT PHASE IN EE MODE Select the timecode output mode for output from the TIME CODE OUT
connector in E-E mode.
thru (through): Output the timecode input to the TIME CODE IN
connector as it is.
v-in (video input phase): Output the timecode with the same phase as
the input video signal phase.
v-out (video output phase): Output the timecode with the same phase
as the output video signal phase.
612
618
619
TC OUTPUT MUTING IN SEARCH Select whether to suppress the output from the TIME CODE OUT
MODE
connector in jog/shuttle mode.
on: Suppress.
off: Do not suppress.
a)
Select the source of the VITC embedded into output HDSDI when up
converting during playback of SD discs.
UPCONV EMBEDDED VITC
VITC: Select the VITC of the SD disc.
LTC: Select the LTC of the SD disc.
a)
Select whether to record the VITC generated by the internal timecode
generator during IMX recording.
VITC
off: Do not record the internally generated VITC.
on: Record the internally generated VITC.
Note
Even if this item is set to “off”, VITC is recorded if the input video signal
contains VITC and the VITC line is set to “thru” in menu item 723.
651
652
UMID SDI OUTPUT
Select whether to output UMID in the VANC of the SDI output.
off: Do not output.
on: Output.
b)
Select the line in which UMID is output when menu item 651 is set to
“on”.
UMID SD VANC LINE
12 H (12 line), 13 H (13 line), 15 H (15 line), 16 H (16 line), 17 H (17
line), 18 H (18 line), 19 H (19 line) (59.94i/59.94P/29.97P mode)
9 H (9 line), 10 H (10 line), 12 H (12 line), 13 H (13 line), 14 H (14 line),
15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line) (50i/50P/
25P mode)
134
Setup Menu
Menu items in the 600s, relating to the timecode, metadata, and UMID
Settings
Item number Item name
653
UMID HD VANC LINE
Specify the HDSDI signal VANC line into which the UMID should be
inserted.
9H to 17H to 20H (59.94i, 50i, 29.97P, 25P, 23.98P mode)
9H to 17H to 25H (59.94P, 50P mode)
Note
The output VANC line during playback follows the setting for recording.
657
660
ESSENCE MARK SDI OUTPUT
ESSENCE MARK SD VANC LINE
Select whether to output essence marks in the SDI output VANC.
off: Do not output.
on: Output.
b)
When menu item 657 is set to “on”, select the line to which to output
essence marks.
12 H (12 line), 13 H (13 line), 15 H (15 line), 16 H (16 line), 17 H (17
line), 18 H (18 line), 19 H (19 line) (59.94i/59.94P/29.97P mode)
9 H (9 line), 10 H (10 line), 12 H (12 line), 13 H (13 line), 14 H (14 line),
15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line) (50i/50P/
25P mode)
665
ESSENCE MARK HD VANC LINE
METADATA ITEM OUT
When item 657 is set to “on”, select the line to which to output essence
marks.
9H to 17H to 20H (59.94i, 50i, 29.97P, 25P, 23.98P mode)
9H to 17H to 25H (59.94P, 50P mode)
Note
The output VANC line during playback follows the setting for recording.
666
668
Specify whether to include the information from recorded VANC packets
in data items in the DATA ITEM section of MXF files.
off: Do not include VANC packet information in data items.
on: Include VANC packet information in data items.
USER META DATA OUTPUT IN
MXF
Select whether to output user metadata to MXF files.
off: Do not output.
on: Output.
a) HD1500 When the PDBK-S1500 or PDBK-F1500 option is installed.
b) Not displayed when the unit is in 23.98P mode.
135
Setup Menu
Menu items in the 700s, relating to video control
Settings
Item number Item name
703
BLANK LINE SELECT
Switch blanking of the video output signal on or off for individual lines in
the vertical blanking interval.
Sub-Item
ALL LINE
The Y/C signal and odd/even fields are blanked simultaneously.
- - -: Specify the blanking for each line separately.
blnk (blank): Regardless of the setting of other sub-items, blank all lines
which can be specified in this menu item.
thru (throu): Regardless of the setting of other sub-items, switch off
blanking for all lines which can be specified in this menu item.
In 59.94i/
59.94P/29.97P LINE 19
mode (UC)
LINE 12 ...
Specify blanking for lines 12 to 19.
blnk (blank): Carry out blanking.
thru (throu): Switch off blanking.
LINE 20
Specify blanking for line 20.
blnk (blank): Carry out blanking.
half: Carry out half-blanking.
thru (throu): Switch off blanking.
In 59.94i/
59.94P/29.97P LINE 20
mode (J)
LINE 12 …
Specify blanking for lines 12 to 20.
blnk (blank): Carry out blanking.
thru (throu): Switch off blanking.
LINE 21
Specify blanking for line 21.
blnk (blank): Carry out blanking.
half: Carry out half-blanking.
thru (throu): Switch off blanking.
In 50i/50P/25P LINE 9 ...
Specify blanking for lines 9 to 22.
blnk (blank): Carry out blanking.
thru (throu): Switch off blanking.
mode
LINE 22
LINE 23
Specify blanking for line 23.
half: Carry out half-blanking.
thru (throu): Switch off blanking.
705
707
EDGE SUBCARRIER REDUCER Select whether to enable the edge subcarrier reducer (ESR).
MODE
on: Enable.
off: Do not enable.
When playing back a composite signal, set this to “on”.
FORCED VERTICAL
INTERPOLATION OFF
The “Y-add” function is normally switched on automatically during jog or
variable speed playback. This item selects whether to force the “Y-add”
function off.
auto: Automatically switch the “Y-add” function on.
off (forced YADD off): Force the “Y-add” function off.
The “Y-add” function is off while a disc image is displayed in stop mode
(menu item 108 AUTO EE SELECT is “off”).
The “Y-add” function is a circuit operation to interpolate the video signal
vertically during jog or variable speed playback for the purpose of
reducing the vertical movement of the playback picture.
710
INTERNAL VIDEO SIGNAL
GENERATOR
Select the test signal to be output from the internal test signal generator.
When V INPUT on the P1 VIDEO page of the function menu is set to
“SG”, the internal test signal generator operates to output the selected
test signal. This signal can also be recorded.
CB75 (75% Color Bars): 75% color bar signal
CB100 (100% Color Bars): 100% color bar signal
MLTBS (Multi Burst): Multi-burst signal
10STEP (10 steps): 10-step signal
PLSBR (Pulse and Bar): Pulse and bar signal
RAMP (Ramp): Ramp signal
BLACK (Black): Black signal
ARIB CB (ARIB Color Bars): ARIB color bar signal, modify width, 100%
Note
ARIB CB cannot be specified when SD recording is selected. If ARIB CB
is selected, the selection is changed to CB75 (75% Color Bars).
136
Setup Menu
Menu items in the 700s, relating to video control
Item number Item name
Settings
b)
713
Set the video setup amount to be added to the composite output signal (in
59.94i/59.94P/29.97P mode only).
VIDEO SETUP REFERENCE
Sub-item
OUTPUT
LEVEL
In 59.94i/59.94P/ Add the setup level selected by this item to the output signal.
29.97P mode (UC) 0.0%, 7.5%
In 59.94i/59.94P/ Add the setup level selected by this item to the output signal.
29.97P mode (J)
0.0%, 7.5%
715
716
717
718
VIDEO GAIN CONTROL
Adjust the video output level.
–2048 to 0 to 848
CHROMA GAIN CONTROL
CHROMA PHASE CONTROL
Adjust the chroma output level.
–2048 to 0 to 848
Adjust the chroma phase.
–128 to 0 to 127
SETUP LEVEL (59.94i/59.94P/
29.97P/23.98P mode)/BLACK
LEVEL (50i/50P/25P mode)
Adjust the setup level (black level).
–272 to 0 to 272
b)
719
720
723
SYSTEM PHASE SYNC
Adjust the output signal sync phase.
–128 to 0 to 127
SYSTEM PHASE SC
Adjust the output signal subcarrier phase.
0 to 511
a)
Switch blanking on or off for lines in the vertical blanking interval of input
video signals. Lines can be specified individually. Y/C signals and odd/
even fields are blanked simultaneously.
INPUT VIDEO BLANK
Sub-Item
Blanking in recorded signals is carried out according to these settings.
1
ALL LINE
- - -: Specify the blanking for each line separately.
blnk (blank): Regardless of the settings of other sub-items, blank all lines
which can be specified in this menu item.
thru (throu): Regardless of the settings of other sub-items, switch
blanking off for all lines which can be specified in this menu item.
2...10 LINE 12 In 59.94i/59.94P/ Specify blanking for lines 12 to 20.
...
29.97P mode
blnk (blank): Switch blanking on.
thru (throu): Switch blanking off.
LINE 20
2...15 LINE 9 In 50i/50P/25P
Specify blanking for lines 9, 322 to 22, and 335.
blnk (blank): Switch blanking on.
thru (throu): Switch blanking off.
...
mode
LINE 22
726
H BLANKING WIDTH
Select the horizontal blanking width of the output analog video signal.
narow (narrow): Digital blanking (narrow)
wide: Analog blanking (wide)
When “wide” is selected, the horizontal blanking width complies with
SMPTE170M, and normally the blanking is widened and the image
becomes narrower. It is recommended to select “narow” at the editing
stage, then later, for broadcast transmission to select “wide”, to output a
signal conforming to the standard. Note, however, that “narow” has to be
always selected for SDI signals.
728
OUTPUT SCH PHASE
Set the subcarrier H phase.
–512 (–512 (DEC))... 0 (0 (DEC))... 511 (511 (DEC))
137
Setup Menu
Menu items in the 700s, relating to video control
Settings
Item number Item name
731
WIDE MODE
Sub-Item
Specify whether to record and play back with the addition of wide picture
information.
a)
1
Select whether to save wide picture information to the disc when
recording.
INPUT
auto: Automatically save wide picture information when it is detected in
the selected input video signal.
on: Always save wide picture information.
off: Never save wide picture information.
2
OUTPUT
Select whether to add wide picture information to the signal output when
down-converter output is set to squeeze mode.
thru (through): Do not add.
auto: Add.
Notes
• To add wide picture information to the output signal, another setting is
required in addition to this item. In setup menu item 703, set line 16
(59.94i/59.94P/29.97P/23.98P mode (J)), line 20 (59.94i/59.94P/
29.97P/23.98P mode (UC)), or line 23(50i/50P/25P mode) to “thru”.
• In 59.94i/59.94P/29.97P/23.98P mode (J), output of wide picture
information is given priority if the VITC insertion line is set to line 16 in
setup menu item 601 or 602.
• In 59.94i/59.94P/29.97P/23.98P mode (UC), output of wide picture
information is given priority if the VITC insertion line is set to line 20 in
setup menu item 601 or 602.
740
MASTER LEVEL (HD)
Adjust the high-definition video signal output from the HDSDI OUTPUT 1,
2 (SUPER) connectors. This adjusts the Y, PB, and PR levels
simultaneously.
–2048 to 0 to 846
741
742
743
745
746
747
Y LEVEL (HD)
Adjust the Y level of the high-definition video signal output from the
HDSDI OUTPUT 1, 2 (SUPER) connectors.
–2048 to 0 to 846
PB LEVEL (HD)
PR LEVEL (HD)
SETUP LEVEL (HD)
SYNC PHASE (HD)
FINE (HD)
Adjust the PB level of the high-definition video signal output from the
HDSDI OUTPUT 1, 2 (SUPER) connectors.
–2048 to 0 to 846
Adjust the PR level of the high-definition video signal output from the
HDSDI OUTPUT 1, 2 (SUPER) connectors.
–2048 to 0 to 846
Adjust the setup level of the high-definition video signal output from the
HDSDI OUTPUT 1, 2 (SUPER) connectors.
–272 to 0 to 272
Control the H sync phase of the high-definition video signal output from
the HDSDI OUTPUT 1, 2 (SUPER) connectors.
–128 to 0 to 127
Fine control the H sync phase of the high-definition video signal output
from the HDSDI OUTPUT 1, 2 (SUPER) connectors.
0 to 1023
a) HD1500 When the PDBK-S1500 or PDBK-F1500 option is installed.
b) Not displayed when the unit is in 23.98P mode.
Menu items in the 800s, relating to audio control
Item number Item name
802 DIGITAL AUDIO MUTING IN
SHUTTLE MODE
Settings
Set the audio muting conditions during shuttle playback.
off: Not muted.
on: Muted.
138
Setup Menu
Menu items in the 800s, relating to audio control
Settings
Item number Item name
807
808
815
AUDIO OUTPUT PHASE
Set the output timing of digital audio playback signals (HDSDI, SDI, AES/
EBU only), with 80H as a reference position. Output timing is earlier for
values smaller than 80H and later for values greater than 80H. (80H, 128
samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs)
0 (0 (HEX))... 80 (80 (HEX))... FF (FF (HEX)): Values can be set in this
range.
INTERNAL AUDIO SIGNAL
GENERATOR
Select the operation of the internal audio test signal generator.
silnc (silence): Silent signal.
1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.
When you set the A1 INPUT item on page P2 AUDIO of the function
menu to “SG”, the internal signal generator operates and outputs
AUDIO SAMPLING RATE
CONVERTER
Select the mode of operation of the sampling rate converter for AES/
EBU input to channels 1 to 4.
off: Do not operate.
on: Operate.
819
823
[F1600]
AUDIO INPUT ARRANGE
Set up mixing of audio signals.
NON-AUDIO FLAG PB
Sub-item
Control non-audio flags in digital audio output.
1
2
3
4
CH1/CH2
CH3/CH4
CH5/CH6
CH7/CH8
During playback (except E-E mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto: Set as follows.
• When data is read from disc and confirmed: Follow the data.
• When data from disc is not confirmed: Maintain current state.
824
827
ANALOG LINE OUTPUT SELECT
Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
AES/EBU AUDIO OUTPUT SELECT Select the audio signals to assign to AES/EBU audio output channels.
Sub-item
1
2
CH1/CH2
CH3/CH4
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
828
SDI AUDIO OUTPUT SELECT
Sub-item
Select the audio signals to assign to SDI audio output channels.
1
CH1/CH2
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2
CH3/CH4
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
a)
831
Select the number of output channels for i.LINK TS (HDV) signals.
4ch: 4 channels
2ch: 2 channels
TS OUT AUDIO MODE
139
Setup Menu
Menu items in the 800s, relating to audio control
Item number Item name
Settings
834
AUDIO INPUT LEVEL
Sub-item
Select the analog audio input source.
1
CH1
line: Line input
mic: Microphone input
2
CH2
line: Line input
mic: Microphone input
839
840
AUDIO AGC/LIMITER MODE
AUDIO AGC SELECT
For automatic input level adjustments performed on the analog audio
signals recorded on channels 1 and 2, select whether to perform the
adjustments in stereo mode or independently for channels 1 and 2.
mono: Perform automatic adjustments independently for channels 1 and
2.
stereo: Perform automatic adjustments in stereo mode.
Set the AGC saturation level.
off: AGC does not operate.
–6dB, –9dB, –12dB, –15dB, –17dB: AGC operates when the
VARIABLE switch is set to PRESET.
Note
This setting is valid only for channels where “mic” is selected with setup
menu item 834 AUDIO INPUT LEVEL. Regardless of this setting, AGC is
“off” for channels where “line” is selected.
841
AUDIO LIMITER SELECT
Select the limiter saturation level, for limiting large input signals, for use
in manual adjustment of audio input levels.
off: The limiter does not operate.
–6dB, –9dB, –12dB, –15dB, –17dB: The limiter operates when the
VARIABLE switch is set to PRESET.
Note
This setting is valid only for channels where “mic” is selected with setup
menu item 834 AUDIO INPUT LEVEL. Regardless of this setting, the
limiter is “off” for channels where “line” is selected.
a) When the PDBK-201 option board is installed
Menu items in the 900s, relating to digital process
Item number Item name
Settings
920
SD-SDI H-ANC CONTROL
Sub-item
Select whether to add information to the SDI output.
1
AUDIO 5CH-8CH
off: Do not add digital audio data channels 5 to 8.
on: Add digital audio data channels 5 to 8.
2
RP188 ATC
off: Do not add RP188 timecode data.
on: Add RP188 timecode data.
a)
923
930
Select whether to use auto squeeze mode.
off: Do not use.
on: Use.
AUTO SQUEEZE
DOWN CONVERTER MODE (DC)
Select the down-converter mode.
crop: Select the edge-crop mode.
l-box: Select the letter box mode.
squez: Select the squeeze mode.
931
DOWN CONVERTER LETTER BOX Select the aspect ratio of the down-converter output when menu item
MODE (DC)
930 is set to “l-box”.
16:9: Set the aspect ratio of the HD-SD converter output to 16:9.
14:9: Set the aspect ratio of the HD-SD converter output to 14:9.
13:9: Set the aspect ratio of the HD-SD converter output to 13:9.
932
934
H CROP POSITION (DC)
CROSS COLOR (DC)
Adjust the H-crop (the horizontal position when cropping in the edge crop
mode) of the down converter output when menu item 930 is set to “crop”.
–120 to 0 to 120
Adjust the down-converter cross color.
0 to 8 to 15
140
Setup Menu
Menu items in the 900s, relating to digital process
Settings
Item number Item name
DETAIL GAIN (DC)
935
936
937
938
939
940
942
Adjust the down-converter image enhancer, the sharpness of edge
enhancement.
0 to 7FH
LIMITER (DC)
CRISP (DC)
Adjust the down-converter image enhancer, the maximum detail level
added to emphasize the original signal.
0 to 20H to 3FH
Adjust the down-converter image enhancer, the threshold amplitude at
which low amplitude signals are not emphasized.
0 to FH
LEVEL DEPEND THRESHOLD (DC) Adjust the down-converter image enhancer. Set the luminance range for
edge enhancement.
0 to 8 to FH
H DETAIL FREQUENCY (DC)
H/V RATIO (DC)
Adjust the down-converter image enhancer. Set the central frequency for
edge enhancement.
2.6MHz, 3.4MHz, 3.9MHz, 4.6MHz
Adjust the down-converter image enhancer. Set the horizontal/vertical
ratio for edge enhancement.
0 to 3 to 7
V FILTER SELECT (DC)
CROSS COLOR CRISP (DC)
Set the vertical interpolation filter coefficient for down-converter output (in
1080 mode only).
1 to 3
943
950
Set the cross color crisp level for down-converter output.
0 to 4 to FH
a)
Select the up-converter mode.
UP CONVERTER MODE
EDGE CROP: Select the edge-crop mode.
LETTER BOX: Select the letter box mode.
SQUEEZE: Select the squeeze mode.
a)
951
952
Adjust the H-crop (the horizontal position when cropping in the edge crop
mode) of the up converter output when menu item 950 is set to “crop”.
–120 to 0 to 120
H CROP POSITION (UC)
a)
When menu item 950 is set to “l-box”, adjust the vertical location of the
position where the picture is cut out for up converter output in letter box
LETTER BOX POSITION (UC)
mode.
–120 to 0 to 120
a)
953
954
955
956
957
958
Select the source picture to use in converting SD to HD.
FIELD: Use field pictures.
UP CONVERTER PROCESS (UC)
ADAPTIVE: Frame or field is selected automatically.
a)
Adjust the up-converter image enhancer, the sharpness of edge
enhancement.
0 to 40H to 7FH
DETAIL GAIN (UC)
a)
Adjust the up-converter image enhancer, the maximum detail level added
to emphasize the original signal.
0 to 20H to 3FH
LIMITER (UC)
a)
Adjust the up-converter image enhancer, the threshold amplitude at
which low amplitude signals are not emphasized.
0 to 8 to FH
CRISP THRESHOLD (UC)
Adjust the up-converter image enhancer. Set the luminance range for
edge enhancement.
0 to 8 to FH
LEVEL DEPEND THRESHOLD (UC)
a)
a)
Adjust the up converter image enhancer. Set the center frequency and
frequency properties for edge enhancement.
3.2MHz: 3.2 MHz 1.1 MHz
H DETAIL FREQUENCY (UC)
4.5MHz: 4.5 MHz 1.4 MHz
5.0MHz: 5.0 MHz 0.7 MHz
4.0MHz: 4.0 MHz 2.0 MHz
141
Setup Menu
Menu items in the 900s, relating to digital process
Settings
Item number Item name
a)
959
Adjust the up-converter image enhancer. Set the horizontal/vertical ratio
for edge enhancement.
H/V RATIO (UC)
0 to 3 to 7
965
IMAGE ENHANCER (INPUT UP
CONVERTER)
Set up the operation of the up converter image enhancer for SD input,
separately from the settings for playback (menu items 950 to 959).
Sub-Item
a)
1
pb: While SD signals are input, make the behavior of the image
enhancer of the up-converter follow the settings for playback (menu
items 950 to 959) (Settings for sub-items 2 to 11 under menu item
965 become invalid).
ENH SETTING
input: While SD signals are input, make the behavior of the image
enhancer of the up-converter follow the settings for sub-items 2 to 11
under menu item 965 (separate settings during input of SD signals
from those during playback).
2
3
4
CONVERT
H CROP P
L BOX P
Select the up-converter mode.
CROP: Select the edge-crop mode.
L-BOX: Select the letter box mode.
SQUEZ: Select the squeeze mode.
When sub-item UP CONVERTER MODE of menu item 965 is set to
“crop”, adjust the H-crop (horizontal crop) position for up converter output
in edge crop mode.
–120 to 0 to 120
When sub-item UP CONVERTER MODE of menu item 965 is set to “l-
box”, adjust the vertical location of the position where the picture is cut
out for up converter output in letter box mode.
–120 to 0 to 120
5
6
7
8
9
CNV PROC
DETAIL
Select the source picture to use in converting SD to HD.
FIELD: Use field pictures.
ADAPT: Frame or field is selected automatically.
Adjust the up-converter image enhancer. Set the sharpness of edge
enhancement.
0 to 40H to 7FH
LIMITER
CRISP
Adjust the up-converter image enhancer. Set the maximum detail level
added to emphasize the original signal.
0 to 20H to 3FH
Adjust the up-converter image enhancer. Set the threshold amplitude at
which low amplitude signals are not emphasized.
0 to 8 to FH
DEPEND
Adjust the up-converter image enhancer. Set the luminance range for
edge enhancement.
0 to 8 to FH
10 H DETL F
Adjust the up converter image enhancer. Set the center frequency and
frequency properties for edge enhancement.
3.2MHz: 3.2 MHz 1.1 MHz
4.5MHz: 4.5 MHz 1.4 MHz
5.0MHz: 5.0 MHz 0.7 MHz
4.0MHz: 4.0 MHz 2.0 MHz
11 HV RATIO
Adjust the up-converter image enhancer. Set the horizontal/vertical ratio
for edge enhancement.
0 to 3 to 7
a) HD1500 When the PDBK-S1500 or PDBK-F1500 option is installed.
However, since with the factory default settings the
extended menu is not displayed, it is first necessary to
enable display of the extended menu.
Extended menu operations
To enable display of the extended menu
Proceed as follows to use the maintenance menu.
The extended menu can be used with the same procedures
as in the basic menu.
142
Setup Menu
1
Holding down the PAGE/HOME button and the
SHIFT button, press the MENU button.
When you next display the menu and change the item
display, the extended menu will appear after the basic
menu.
The maintenance menu appears on the video monitor
display.
MAINTENANCE MENU
M0:CHECK
M1:ADJUST
p
M2:SERVICE SUPPORT
M3:OTHERS
M4:SETUP MAINENANCE
M5:NETWORK
M6:DRIVE
2
Turn the PUSH SET(S.SEL) knob to select “M4
SETUP MAINTENANCE”, then press the PUSH
SET(S.SEL) knob or the SELECT function button
(F2).
The sub-items of M4: SETUP MAINTENANCE
appears.
MAINTENANCE MENU
M4:SETUP MAINTENANCE
PM40:EXTEND MENU: dis
M40:CUSTOMIZE : dis
M46:MENU DATA CONTROL
M47:SETUP BANK4
p
M48:AUTO RECALL: off
M49:RESET ALL SETUP
3
Turn the PUSH SET(S.SEL) knob to select “M40
EXTENDED MENU”, then press the PUSH
SET(S.SEL) knob or the SELECT function button
(F2).
The setting screen for M40: EXTENDED MENU
appears.
MAINTENANCE MENU
M4:SETUP MAINTENANCE
M40:EXTEND MENU: dis
P
* DISABLE
ENABLE
p
4
Turn the PUSH SET(S.SEL) knob to select
“ENABLE”, and press the SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor display, and “Saving...” appears in the time
data display area, while the new settings are saved in
memory. When the saving operation is completed, the
video monitor display and the time data display area
return to their normal indications.
143
Setup Menu
Maintenance Menu
Items in the maintenance menu
The following tables show the items in the maintenance
menu.
• The values in the Settings columns are the values which
appear in the time data display area. (The values may
appear in a different format on an external monitor. In
this case, the external monitor values are shown in
parentheses.) Underlined values are the factory defaults.
• Item names are the names which appear on the video
monitor of this unit and an external monitor to which the
output of the COMPOSITE OUTPUT 2 (SUPER)
connector, the SDSDI OUTPUT 2 (SUPER) connector,
or the HDSDI OUTPUT 2 (SUPER) connector is input.
An abbreviated name appears in the time data display
area when you press the NEXT button.
This manual does not explain the menu items in M0:
CHECK, M1: ADJUST, M2: SERVICE SUPPORT, and
M6: DRIVE. Refer to the Maintenance Manual for an
explanation of these items.
M3: OTHERS: Other setting items
Setting
Item
M30: SOFTWARE VERSION
M31: SERIAL NUMBER
Display of the software version of this unit
Display of the serial number of this unit
M33: FILE I/F
CONFIG
PROAV DISPLAY
Selects whether or not to display PROAV directory.
DISABLE: Do not display PROAV directory.
ENABLE: Display PROAV directory.
PC REMOTE
Disables or enables a FAM connection.
ENALBE: Enable a FAM connection.
F-KEY SELECT: Enable or disable a FAM connection using the function menu.
M36: HOURS METER RESET
Display and reset of the hours meter and the thread counter
M37: AUDIO
CONFIG
M370: HEAD ROOM
Select the audio reference level (headroom).
–20dB, –18dB, –16dB, –12dB, EBUL
Note
EBUL can be selected only when the system frequency is 50i/50P/25P.
M371: DATA LEN
Select the audio channel configuration for IMX recording.
16bit × 8ch: 16-bit, 8-channel configuration
24bit × 4ch: 24-bit, 4-channel configuration
M372: NON-AUDIO
INPUT
Select whether to handle digital audio signals as non-audio signals during
recording.
Audio (audio): Handle as linear PCM audio signals.
data: Handle as non-audio signals.
Sub-Item
1
2
3
4
Tr1/Tr2
Tr3/Tr4
Tr5/Tr6
Tr7/Tr8
M373: INPUT LEVEL
Set the upper limit for the signal level input to audio channels 1/3 or 2/4.
+4dB, 0dB, –3dB, –6dB, EBUL
Sub-Item
1
2
CH1/CH3
CH2/CH4
Note
EBUL can be selected only when the system frequency is 50i/50P/25P.
M377: OUTPUT LEVEL
Set the reference level for audio output signals.
+4dB, 0dB, –3dB, –6dB, EBUL
Note
EBUL can be selected only when the system frequency is 50i/50P/25P.
144
Maintenance Menu
M3: OTHERS: Other setting items
Setting
Item
M38: F-KEY
CONFIG
For details, refer to the Maintenance Manual.
M380: HOME2
Assign a function menu item to page HOME2 of the function menu as a user
setting.
M381: PAGE8 ASSIGN
M382: PAGE8 NAME
Assign a setup menu item to page P8 of the function menu as a user setting.
Specify the name of a setup menu item assigned with M381: PAGE8 ASSIGN.
Save the settings of M380 to M382.
M38F: NV-RAM
CONTROL
M39: OTHER
CONFIG
M390: MIXED REC
Select whether to enable mixed format recording mode.
DISABLE: Do not enable.
ENABLE: Enable.
M391: VITC REC
Select whether to record the VITC in the input HDSDI signals in the LTC user bits
area.
DIS: Do not record.
ENA: Record.
M392: PB POS
When you switch between the clip playback screen and the clip list playback
screen, specifies the clip or sub clip playback start position.
KEEP: Play from the position where playback stopped.
FORCED TOP: Play from the first frame of the first clip or sub clip.
[F1600]
M393: AUDIO DSP
Select the function for which the audio digital signal processor shall be used.
linear edit: Use for linear editing (microphone input is disabled).
AGC/limiter: Use for microphone input (linear editing is disabled).
Note
It is not possible to use the audio digital signal processor for multiple functions at
the same time.
145
Maintenance Menu
M3: OTHERS: Other setting items
Item
Setting
M3B: VANC RX M3B0: VANC RX
For setting HDSDI VANC data input parameters
PARAMETER
PACKET
Notes
• In 59.94i, 50i, 29.97P or 25P mode, selecting the line also selects the
corresponding line in the second field (for example, if line 9 is selected, line 527
is also selected for VANC packet reception).
• Menu item M3B0 enables recording of one VANC packet when the selected line
contains any packets whose DID/SDID matches the value set with this menu
item.
• Up to four packets are recorded per each line regardless of the DID and SDID
for the VANC set with menu item M3B1 or M3B2.Menu items M3B1 and MSB2
enable recording of up to four VANC packets in the selected line, respectively,
regardless of the DID/SDID value.
• It is not possible to set the same line with menu items M3B0, M3B1, and M3B2.
If the same line is specified, priority is given in the order of M3B0, M3B1, and
M3B2 (for example, if the same line is specified with M3B0 and M3B1, the
setting with M3B1 is ignored).
• When VANC data is output to HDSDI playback signals, the number of the
output VANC line is the same as that of the input VANC line.
• When a UMID or essence mark line is selected with M3B1 or M3B2, UMID or
essence mark output takes priority. To disable UMID or essence mark output,
set setup menu item 651 or 657 to “off”.
Sub-item
1
LINE
Selects the lines for the VANC to be received.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
2
3
DID
Specification of the DID of the VANC to receive
00h-FFh
SDID
Specification of the SDID of the VANC to receive
00h-FFh
M3B1: LINE1 SEL
M3B2: LINE2 SEL
Selects the lines to be received for the HDSDI VANC data.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
Selects the lines to be received for the HDSDI VANC data.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
M3C: POWER SAVE CONTROL
Specification of whether to enable the power saving function
OFF, ON
M3D: DATE/TIME PRESET
M3E: USB MEMORY UTIL
Specification of the date and time
For installation of software upgrade
For details, refer to the Maintenance Manual.
For details, refer to the Maintenance Manual.
M3F: FACTORY SETUP
M4: SETUP MAINTENANCE: items relating to the setup menu
Setting
Item
M40: EXTENDED MENU
Select whether to display the extended menu.
DISABLE: Do not display.
ENABLE: Display.
M41: CUSTOMIZE
Select whether to enable the customization function of the setup menu.
DISABLE: Do not display.
ENABLE: Display.
146
Maintenance Menu
M4: SETUP MAINTENANCE: items relating to the setup menu
Item
Setting
M46: MENU
DATA
CONTROL
M461: MENU
STATUS
DISPLAY
Displays the status of the menu bank where the current menu settings are stored.
M462: SAVE
MENU DATA
Select whether to temporarily back up (save) setup menu settings before operations such as
software upgrades.
SAVE function button (F5): Back up (save) the settings.
MENU button: Return to next highest menu level without backing up.
M463: LOAD
MENU DATA
Select whether to restore (load) setting that were backed up (saved) with the “SAVE MENU
DATA” item.
SAVE function button (F5): Restore (load) the settings.
MENU button: Return to the next highest menu level without restoring.
M47: SETUP BANK4
Select the bank to be stored in menu bank 4, or reset menu bank 4.
CURRENT TO BANK4: Store the current menu settings in menu bank 4.
BANK1 TO BANK4: Store the menu bank 1 settings in menu bank 4.
BANK2 TO BANK4: Store the menu bank 2 settings in menu bank 4.
BANK3 TO BANK4: Store the menu bank 3 settings in menu bank 4.
RESET BANK4: Reset menu bank 4.
M48: AUTO RECALL
Select whether to recall settings automatically from a menu bank when the system is
powered on, and if so which menu bank to recall from.
off: Do not recall settings from a menu bank.
from BANK1: Recall settings from menu bank 1.
from BANK2: Recall settings from menu bank 2.
from BANK3: Recall settings from menu bank 3.
from BANK4: Recall settings from menu bank 4.
M49: RESET ALL SETUP
Reset the current menu settings to the factory settings.
SAVE function button (F5): Reset.
MENU button: Return to the next highest menu level without resetting.
Notes
• The system frequency setting is also cleared. If you execute this item, reset the system
• Date and time settings are not cleared, but the time zone setting is cleared. After executing
M5: NETWORK: items relating to network settings
Setting
Item
M50: DHCP
Set whether to assign an IP address automatically with the DHCP server.
DISABLE: Do not assign automatically.
ENABLE: Assign automatically.
M51: IP ADDRESS PRESET
Set the IP address of this unit.
192.168.001.010
Notes
• IP address cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired IP address of this unit, close the maintenance menu
and then open it again.
M52: SUBNET MASK PRESET Set the subnet mask.
255.255.255.000
Notes
• Subnet mask cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired subnet mask, close the maintenance menu and then
open it again.
147
Maintenance Menu
M5: NETWORK: items relating to network settings
Setting
Item
M53: DEFAULT GATEWAY
PRESET
Set the address of the default gateway.
000.000.000.000
Notes
• The address of the default gateway cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired address of the default gateway, close the maintenance
menu and then open it again.
M54: LINK SPEED
M55: DUPLEX
Set the communications speed.
AUTO, 10Mbps, 100Mbps, 1000Mbps
Set the communications method.
AUTO, Full Duplex, Half Duplex
a)
Set the size of jumbo frames.
9014, 4088, OFF(1514)
M56: JUMBO FRAME
Note
This value does not include the 4 bytes of the FCS (Frame Check Sequence).
M57: DNS1
M58: DNS2
Set the address of DNS server 1.
000.000.000.000
Notes
• The address of DNS server 1 cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired address of DNS server 1, close the maintenance
menu and then open it again.
Set the address of DNS server 2.
000.000.000.000
Notes
• The address of DNS server 2 cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired address of DNS server 2, close the maintenance
menu and then open it again.
M59: UPnP
Select whether to enable the UPnP (universal plug and play) function.
DISABLE: Disable the UPnP function.
ENABLE: Enable the UPnP function.
M5F: RESET NET CONFIG
Reset network settings to the factory defaults.
SAVE function button (F5): Reset.
MENU button: Return to the next highest menu level without executing the reset.
a) A jumbo frame is a frame larger than the maximum 1514 bytes (not
including FCS) of the standard Ethernet frame. Jumbo frames make it
possible to deliver larger payloads per packet. Since fewer packets need to
be routed, packet processing overhead is lower and network throughput is
potentially improved. (Note that this item is enabled only when LINK
SPEED is set to “1000Mbps”. For it to work, all other devices that handle
packets on the network must also support jumbo frames.)
The maintenance menu appears on the video monitor
display and the currently-set menu item is displayed in
reverse video.
Meanings of indications on the menu
screen
Maintenance menu operations
On-screen indication Meaning
Right-pointing arrow
(c) at the right of a
menu item
Pressing the PUSH SET(S.SEL)
knob or the b/OUT button switches
to the next lower menu level or to a
setting selection screen.
This section describes the indications in the maintenance
menu and how to change the settings.
Left-pointing arrow (C) Pressing the PUSH SET(S.SEL)
To display the maintenance menu
Holding down the PAGE/HOME button and the SHIFT
button, press the MENU button.
at the left of a menu
item
knob or the B/IN button switches to
the previous (higher) menu level.
148
Maintenance Menu
To cancel changing a setting
On-screen indication Meaning
Before pressing the SAVE function button (F5), press the
MENU button.
The menu disappears from the video monitor display,
without saving the new setting.
Character string at the Current setting of the menu item
right of a menu item
When shown with a colon (:): the
current setting is the same as
the factory default setting.
When shown with a raised dot
(.): the current setting is
different from the factory
default setting.
To change network settings
To change network settings, carry out the procedure
described in the previous section, “To display the
maintenance menu”, to display the NETWORK menu
item, then carry out the following operations.
An * (asterisk) in a
Factory default setting
complete list of settings
To change a menu item setting
Carry out the following operations to change the setting.
For details of the settings, consult your network
administrator.
For information about how to change network settings see
next section “To change network settings”.
When the IP address is assigned automatically
Note
Arrow buttons
PUSH SET(S.SEL) knob
Function buttons
Check that the network cable is connected to this unit
before carrying out the operation.
Follow the procedure as shown in previous section “To
change a menu item setting” to set maintenance menu item
M5: NETWORK >M50: DHCP to “ENABLE”.
EJECT
MARK1
PUSH SET(S.SEL)
ACCESS
IN
OUT
CH-1
CH-3
CH-4
MENU
MARK2
SHTL/JOG
ALL CH
VAR/JOG
To check the assigned IP address
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS PRESET.
CH-2
RESET
CHAPTER
EXPAND
RETURN
VARIABLE KEY INHI
REC
PRE-
PAGE
NET
LOCAL
ON
SET
PB
OFF
REMOTE
HOME
PHONES
LEVEL
PREV
PLAY
NEXT
STOP
REC
DISPLAY
SHIFT
THUMBNAIL
SUB CLIP
DISC MENU
TOP
F
REV
F
FWD
END
STANDBY REC INHI
Note
If the IP address cannot be assigned, this is shown as
“000.000.000.000.” In this case, consult the network
administrator.
SHIFT button
PAGE/HOME button
MENU button
To set the IP address
First set DHCP to “DISABLE” (see the previous section,
“When the IP address is assigned automatically”).
1
2
Use the PUSH SET(S.SEL) knob or the V/MARK1
and v/MARK2 buttons to select the required item,
then press the PUSH SET(S.SEL) knob or the
SELECT function button (F2).
1
2
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS PRESET.
The sub-items of the selected item appears.
Press the PUSH SET(S.SEL) knob.
Select a sub-item with the same operation as step 1,
and use the PUSH SET(S.SEL) knob or the V/MARK1
and v/MARK2 buttons to change the setting.
The IP address appears, and the digit that can be
changed flashes.
3
4
Press the PUSH SET(S.SEL) knob or the SELECT
function button (F2) to confirm the setting change.
3
Set the IP address.
To select a different digit to be changed
Use the B/IN and b/OUT buttons.
Press the SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor display, and “Saving...” appears in the time
data display area, while the new settings are saved in
memory. When the saving operation is completed, the
video monitor display and the time data display area
return to their normal indications.
To change the value of a digit
Turn the PUSH SET(S.SEL) knob.
Turning clockwise increases the value, and turning
counterclockwise decreases the value.
The V/MARK1 and v/MARK2 buttons can be used.
149
Maintenance Menu
To return to the factory default setting
Press the RESET/RETURN button.
2
3
Press the PUSH SET(S.SEL) knob.
The communications protocols (AUTO, Full Duplex,
Half Duplex) appear, and the arrow flashes.
4
When all digits are set, press the SAVE function
button (F5).
Press the PUSH SET(S.SEL) knob or use the V/
MARK1 or v/MARK2 button to select a
communications protocol.
This returns to the NETWORK menu.
5
6
7
Repeat steps 1 to 4 as required, to set the subnet mask
and default gateway.
To return to the factory default setting
Press the RESET/RETURN button.
In the NETWORK menu, press the SAVE function
button (F5).
4
Press the SAVE function button (F5).
This returns to the NETWORK menu.
When the “NOW SAVING...” message vanishes,
power the unit off and then on again with the on/
standby button.
To set the communications speed and
protocol
Set the communications speed (LINK SPEED) and
communications method (DUPLEX) to match the network
environment.
To set the communications speed and communications
protocol, proceed as explained in the previous section “To
display the maintenance menu” to display the NETWORK
menu and then proceed as follows.
Contact your network administrator if you have any
questions about the proper settings for these items.
To set the communications speed
1
2
Select maintenance menu item M5: NETWORK
>M54: LINK SPEED.
Press the PUSH SET(S.SEL) knob.
The communications speeds (AUTO, 10Mbps,
100Mbps, and 1000Mbps) appear, and the arrow
flashes.
3
4
Press the PUSH SET(S.SEL) knob or use the v/
MARK1 or V/MARK2 button to select a
communications speed.
To return to the factory default setting
Press the RESET/RETURN button.
Press the SAVE function button (F5).
This returns to the NETWORK menu.
To set the communications protocol
1
Select maintenance menu item M5: NETWORK
>M55: DUPLEX.
150
Maintenance Menu
Planning Metadata
8
Chapter
2) When no UTF-8 format name string is specified, the ASCII format name
string is registered as the actual clip name.
Overview
By loading a file from one of the following locations into
the unit’s memory before starting to record, you can
register the names in the file as clip names.
There are two ways to load files.
• Automatically load a file that has been written to the
following directory on a Professional Disc via an FTP or
FAM connection.
Planning metadata is a file that contains metadata about the
clips to be shot and recorded.
To use planning metadata, you will need to save a file in
advance in one of the locations shown below, and insert
the media into this unit. (Up to 99 planning metadata files
can be saved on one Professional Disc or USB Flash
drive.)
• Use a GUI screen to load a file that has been written to
the following directories on a Professional Disc or a
1)
Professional Disc: General/Sony/Planning directory
USB Flash drive: General/Sony/Planning directory
File creation rules
1) Created automatically when a disc is formatted.
File location
File name
Professional Disc:
• Format that can be used
General/Sony/Planning in the General directory
Manipulating planning metadata
a)
directory
• Extension: XML
This unit allows you to perform the following operations
on planning metadata using the GUI screen.
• To load planning metadata files
• To sort planning metadata
• To check planning metadata properties
• To clear planning metadata
USB memory:General/
Sony/Planning
directory
• ASCII characters (up to
63 characters including
the extension)
• Extension: XML
a) General/Sony/Planning directory is created automatically when a disc is
formatted. Automatically when a disc is formatted.
• To switch the title display in the video monitor screen
Note
Do not save more than 100 planning metadata files in the
above save locations. The unit may fail to load the files
correctly if more than 100 are saved.
To set clip names by using planning
metadata
Clip name string format
In a text editor, modify the two fields in the <Title> tag that
contain the clip name strings (the shaded fields in the
example below).
Enter a name in the first field in ASCII format (up to 13
characters), and enter another name in the second field in
UTF-8 format (up to 52 characters).
The following two types of clip name strings can be
written in a planning metadata file.
• The ASCII format name that appears in the video
1)
monitor screen
• The UTF-8 format name that is actually registered as the
2)
clip name
Clip name string example
1) It is also possible to display the UTF-8 format name, or no name (see
<?xml version="1.0" encoding="UTF-8"?>3
sp
sp
<PlanningMetadata xmlns="http://
sp
151
Overview
xmlns.sony.net/pro/metadata/
planningmetadata" assignId="
• Serial numbers are not reset when you power the unit off
or exchange discs (newly generated numbers are
continuous on the old ones).
sp
P0001" creationDate="
sp
2008-01-20T17:00:00+09:00"splastUpdate="
2008-03-28T10:30:00+09:00"spload="
• If the ASCII format clip name string is longer than 14
characters, it is displayed in the viewfinder as the first 8
characters + x (abbreviated) + the last 4 characters, for
a total of 13 characters.
false" version="1.00">3
sp
<Properties propertyId="
sp
assignment" update="2008-01-20T09:00:
sp
00+09:00" modifiedBy="Chris">3
sp
Typhoon
<Title usAscii="
" xml:lang="
sp
sp
Setting essence mark names by
using planning metadata
Typhoon_Strikes_Tokyo
en">
</Title>3
</Properties>3
</PlanningMetadata>3
You can use planning metadata to specify user-defined
names for the Shot Mark0 to Shot Mark 9 essence marks
that correspond to the 0 to 9 keys on a USB keyboard.
When planning metadata that contains user-defined
essence mark name strings is loaded into this unit’s
memory, the unit displays those names for the essence
marks that correspond to the keys and that are recorded
when the keys are pressed.
In the above example, indicates a space and 3 indicates
sp
a carriage return.
Notes
• When creating a file, write each line as a single
statement, inserting carriage returns only at the indicated
carriage return locations, and inserting no unspecified
spaces.
• If the UTF-8 format string is longer than 52 characters,
the ASCII format string is used as the clip name string.
to load files.
Essence mark name string format
Setting clip names
Use a text editor to enter essence mark names in the
sections indicated by shading in “Essence mark name
string example”. Names can be either in ASCII format (up
to 32 characters) or UTF-8 format (up to 16 characters).
1
2
3
Load a planning metadata file containing clip names
Note
If a name string contains even one non-ASCII character,
the maximum length of that string is 16 characters.
Turn the PUSH SET(S.SEL) knob to display “PLAN”,
and then press the PUSH SET(S.SEL) knob.
Essence mark name string example
Each time that you start recording, the unit
automatically creates clip names using the names
specified in the planning metadata file. An underscore
(_) and a three-digit serial number (001 to 999) is
appended to each clip name.
<?xml version="1.0" encoding="UTF-8"?>3
sp
sp
<PlanningMetadata xmlns="http://xmlns.sony.net/pro/
metadata/planningmetadata" assignId="H00123"
sp
sp
creationDate="2009-04-15T08:00:00Z" lastUpdate=
sp
"2009-04-15T15:00:00Z" version="1.00">3
sp
<Properties propertyId="assignment" class=
sp
Examples of automatically generated clip names
Clip names displayed in the video monitor screenr:
Typhoon_001, Typhoon_002, ...
"original" update="2009-04-15T15:00:00Z"
sp
sp
modifiedBy="Chris">3
<Title usAscii="Football Game" xml:lang=
sp
The actually recorded clip names:
"en">Football Game 15/04/2009</Title>3
Typhoon_Strikes_Tokyo_001,
Typhoon_Strikes_Tokyo_002, ...
<Meta name="_ShotMark1" content=
sp
1)
Goal
"
"/>3
<Meta name="_ShotMark2" content=
sp
1) When display of the ASCII format clip name has been selected (see
Shoot
"
"/>3
<Meta name="_ShotMark3" content=
sp
Corner Kick
"
"/>3
Notes
<Meta name="_ShotMark4" content=
sp
Free Kick
"
"/>3
• The serial numbers return to 001 on the next recording
operation if you reach number 999.
<Meta name="_ShotMark5" content=
sp
Goal Kick
"
"/>3
152
Overview
<Meta name="_ShotMark6" content=
sp
Foul
"
"/>3
<Meta name="_ShotMark7" content=
sp
PK
"
"/>3
<Meta name="_ShotMark8" content=
sp
1st Half
"
"/>3
<Meta name="_ShotMark9" content=
sp
2nd Half
"
"/>3
<Meta name="_ShotMark0" content=
sp
Kick Off
"
"/>3
</Properties>3
</PlanningMetadata>3
In the above example, indicates a space and 3 indicates
sp
a carriage return.
You can check user-defined essence mark name strings in
Note
When you create a definition file, enter each statement as
a single line with a CRLF only after the last character in the
statement line, and do not enter spaces except where
specified, except within essence mark name strings.
153
Overview
Appendix
temperature inside a car with the windows closed can
easily exceed 50°C (122°F).
• In damp or dusty locations
• Locations where the unit may be exposed to rain
• Locations subject to violent vibration
• Near strong magnetic fields
Important Notes on
Operation
• Close to radio or TV transmitters producing strong
electromagnetic fields.
Use and storage
• In direct sunlight or close to heaters for extended periods
Do not subject the unit to severe shocks
The internal mechanism may be damaged or the body
warped.
To prevent electromagnetic interference from
portable communications devices
The use of portable telephones and other communications
devices near this unit can result in malfunctions and
interference with audio and video signals.
Do not cover the unit while operating
Doing so will cause temperatures to rise inside the unit,
possibly resulting in failure.
It is recommended that the portable communications
devices near this unit be powered off.
After use
Turn off the on/standby button.
If you plan not to use the unit for a long time, turn off the
POWER switch on the rear panel as well.
Condensation
Shipping
If you move the unit from a very cold place to a warm
place, or use it in a damp location, condensation may form
on the optical pickup. Then, if the unit is operated in this
state, recording and playback may not be performed
properly.
Do the following to prevent this from happening.
• When you move or operate the unit in an environment
where condensation may form, be sure to insert a disc in
advance.
• Whenever you turn on the on/standby button, check that
the HUMID indicator does not appear on the color LCD.
If it appears, wait until it disappears before inserting a
disc.
• Remove the disc before transporting the unit.
• If sending the unit by truck, ship, air or other
transportation service, pack it in the shipping carton of
the unit.
Care of the unit
If the body of the unit is dirty, clean it with a soft, dry cloth.
In extreme cases, use a cloth steeped in a little neutral
detergent, then wipe dry. Do not use organic solvents such
as alcohol or thinners, as these may cause discoloration or
other damage to the finish of the unit.
In the event of operating problems
If you should experience problems with the unit, contact a
Sony service representative.
About the LCD panel
Use and storage locations
LCD panels are manufactured with extremely high
precision technology that yields effective pixel rates of
99.99% or higher. However, very rarely, one or more
pixels may be permanently dark or permanently lit in
white, red, blue, or green.
Store in a level, ventilated place. Avoid using or storing the
unit in the following places.
• In excessive heat or cold (operating temperature range:
5°C to 40°C (41°F to 104°F))
Remember that in summer or in warm climates the
154
Important Notes on Operation
This phenomenon is not a malfunction. Such pixels have
no effect on the recorded data, and the unit may be used
with confidence even if they are present.
Periodic Maintenance
Digital hours meter
The digital hours meter can provide eight items of
information about the operational history of the unit. The
information can be displayed in the time data display area
and also, by text superimposition, on the monitor
connected to the unit. Use the information as a guide in
scheduling periodic maintenance.
For periodic maintenance, consult a Sony service
representative.
Display modes of the digital hours meter
H01: OPERATION HOURS mode
Displays the total number of hours the unit has been
powered on in units of 1 hour.
H02: LASER PARAMETER 0 mode (not
resettable)
Of the two optical heads, this shows a counter of the
cumulative light output time by one optical head in units of
1)
hours.
This can be used as a guide in determining when to replace
the optical head.
1) The counter advances at different rates during recording and playback. It
is also affected by the ambient temperature.
H03: LASER PARAMETER 1 mode (not
resettable)
Same as H02.
Of the two optical heads, this shows a counter of the
cumulative light output time by the other optical head in
1)
units of hours.
1) The counter advances at different rates during recording and playback. It
is also affected by the ambient temperature.
H11: OPERATION HOURS mode (resettable)
Same as H01 except that the count is resettable.
This can be used as a guide in determining when to replace
parts.
H13: SEEK RUNNING HOURS 0 mode (resettable)
Of the two optical heads, this shows the cumulative seek
operation time for one optical head in units of hours. The
count is resettable.
This can be used as a guide in determining when to replace
the seek motor.
H14: SPINDLE RUNNING HOURS mode
(resettable)
This shows the cumulative spindle rotation time, in units of
hours. The count is resettable.
155
Periodic Maintenance
This can be used as a guide in determining when to replace
the spindle motor.
H15: LOADING COUNTER mode (resettable)
Display the total number of times disc has been loaded in
the unit. The count is resettable.
H17: SEEK RUNNING HOURS 1 mode (resettable)
Same as H13.
Of the two optical heads, this shows the cumulative seek
operation time for the other optical head in units of hours.
The count is resettable.
To display the digital hours meter
Press the MENU button to display the setup menu, then
turn the PUSH SET(S.SEL) knob to display the required
item in the time data display area and on the monitor
connected to the unit.
To exit from the digital hours meter
Press the RETURN function button (F1) to return to the
setup menu.
Press the EXIT function button (F5) to return to the screen
that was displayed before you entered the setup menu.
156
Periodic Maintenance
Troubleshooting
Alarms
An alarm (warning message) appears in the time data
display area when an operation is attempted which is
inappropriate for the settings on this unit or the state of the
disc. Both the alarm message and the action to take to
resolve the problem appear in the monitor video section
and on the screen of the external video monitor connected
to the unit.
R E M O T E !
Example alarm in time data display area
ALARM
REMOTE MODE IS SELECTED.
SET REMOTE/LOCAL/NETWORK
SWITCH TO LOCAL.
Example alarm in monitor video section
When an alarm is displayed, remove the alarm cause by
following the action to take. If the alarm display does not
disappear, contact a Sony service representative.
Please note that there are some alarms which do not appear
depending on the setting of setup menu item 016 ALARM
operations.
When the unit is powered on
Alarm message in time
data display area
Alarm message in video monitor screen
Description/action
ADJ. Mode!
MENU Ver.UP
ILL. SETUP!
THE UNIT IS IN ADJUSTMENT MODE.
This appears when the unit is in adjustment
mode.
Contact a Sony service representative.
CHECK THE SWITCHES OF S2701 ON THE
HPR-23 BOARD AND S1 ON THE VPR-99
BOARD.
THE SETUP MENU SOFTWARE HAS BEEN
UPGRADED.
SET THE SETUP MENU ITEMS TO THE
DESIRED SETTINGS.
Reset the settings in the setup menu (see
INVALID SETTINGS SELECTED IN SETUP
MENU.
SET ITEMS IN THE SETUP MENU TO THE
Reset the settings in the setup menu (see
page 127). If the same message appears after
you reset the settings, contact a Sony service
APPROPRIATE VALUES. CONTACT SERVICE representative.
IF THIS ALARM APPEARS AGAIN AFTER
ABOVE PROCEDURE.
Exchg batt!
Update Err!
BATTERY NEEDS REPLACING. PLEASE
CONTACT SERVICE.
The NVRAM battery is exhausted. Contact a
Sony service representative.
RUN SOFTWARE UPDATE PROGRAM.
The software version is not properly updated.
Update the software version again. If the same
message appears after you update the software
version, contact a Sony service representative.
157
Troubleshooting
When a disc is inserted
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
Unknown FS!
UNKNOWN FILE SYSTEM.
PLEASE FORMAT DISC OR EJECT.
No FS!
NO FILE SYSTEM.PLEASE EJECT DISC. Eject the disc.
ILL. Disc!
IRREGULAR DISC IS USED.
USE PROFESSIONAL DISC.
Use a Professional Disc.
IRREGULAR DISC IS USED.
PLEASE EJECT DISC.
Salvage NG!
Salvage XXXX
DISC CANNOT BE RECORDED.
FORMAT DISC OR CONTACT SERVICE
TO RUN CLIP SALVAGE PROGRAM.
(XXXX)
Over DUR!
EXCESSIVE DURATION IS IN DISC.
RECORDING AND PLAYBACK IS NOT
POSSIBLE.
Data in excess of the rated capacity is recorded on
the disc.
No Support!
FORMAT NOT SUPPORTED.
RECORDING AND PLAYBACK IS NOT
POSSIBLE.
A disc in an unsupported recording format is loaded.
Use a disc in a format supported by this unit.
ILL. Index!
INDEX FILE ERROR.
PLEASE FORMAT DISC OR EJECT.
Formatting!
FORMAT NG!
AUTO FORMATTING IS EXECUTING.
Wait until the format has been completed and try
again.
AUTO FORMATTING WAS NOT
COMPLETED.
Eject the disc and insert it again, or insert another
disc.
DI read err
Read err
CANNOT READ DISC INFORMATION.
PLEASE EJECT DISC.
DRV ADJ err
CANNOT PERFORM AUTO DRIVE
ADJUSTMENT.
During front panel operations
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
a)
KEY INHIBIT MODE IS SELECTED.
SET KEY INHIBIT SWITCH TO OFF.
This appears when the KEY INHI switch is “on”.
Set the KEY INHI switch to “off”.
KEY INHI.!
a)
REMOTE MODE IS SELECTED.
SET REMOTE/LOCAL/NETWORK
SWITCH TO LOCAL.
Set the remote control switch to “LOCAL”.
REMOTE!
a)
NO DISC.
Insert a disc and try again.
No Disc!
158
Troubleshooting
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
REC INHI.!
AUTO FORMATTING WAS NOT
COMPLETED.
Set the disc’s Write Inhibit tab to enable recording
THE DISC WRITE PROTECT TAB IS SET
TO SAVE.
PLEASE EJECT DISC.
THE DISC WRITE PROTECT TAB IS SET
TO SAVE.
AUTO FORMATTING WAS NOT
COMPLETED.
REC INHIBIT MODE IS SELECTED.
CHECK FUNCTION MENU.
PLEASE EJECT DISC.
This appears when REC INH on the HOME page of
the function menu is set to “ON”.
REC INHIBIT.
This appears if you press the REC button when a disc
error has occurred. Correct the disc error and try
again.
b)
NO CLIP.
This appears when a playback, search or delete
operation is attempted on a disc with no clips
recorded on it.
No Clip!
Insert a disc with clips recorded on it.
a)
DISC TOP.
DISC END.
CLIP TOP.
This appears if you press the PREV button or conduct
a high-speed reverse search when the unit is stopped
at the start of the disc.
Disc Top!
Use forward search or playback instead.
a)
This appears if you press the NEXT button or conduct
a forward high-speed search when the unit is stopped
at the end of the disc.
Disc End!
Use reverse search or playback instead.
Clip Top!
Clip End!
This appears in single clip playback mode if you
execute a reverse search when the unit is stopped at
the first frame of a clip. To move to another clip, press
the PREV, NEXT, SHIFT + PREV, or SHIFT + NEXT
button, or perform a thumbnail search.
CLIP END.
This appears in single clip playback mode if you
execute a forward search when the unit is stopped at
the last frame of a clip. To move to another clip, press
the PREV, NEXT, SHIFT + PREV, or SHIFT + NEXT
button, or perform a thumbnail search.
MAX # Clips
MAX # Files
DISC CANNOT BE RECORDED TO.
FOR MORE RECORDING, DELETE
SOME CLIPS.
Delete unneeded clips, or insert a disc with enough
free space.
DISC CANNOT BE RECORDED TO.
FOR MORE RECORDING SPACE,
DELETE CLIPS OR NON-AV DATA.
(GENERAL FILES)
Delete clips or GENERAL files.
Disc Full!
DISC FULL.
FOR MORE RECORDING, DELETE
SOME CLIPS.
Delete unneeded clips, or insert a disc with enough
free space.
b)
NO MORE SUB CLIPS CAN BE ADDED This appears when an attempt is made to add sub
MAX# SB CLP
TO CLIP LIST.
clips when 300 sub clips have already been
registered.
Limit the creation of sub clips to 300 or fewer.
b)
DURATION OF ONE CLIP LIST MUST BE This appears when you try to add a sub clip when the
CL OVER DUR
LESS THAN 24 HOURS.
total duration of sub clips in a clip list has already
reached 24 hours.
Create clip lists so that the total duration is within 24
hours.
159
Troubleshooting
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
Run Salvage
EXECUTE SALVAGE PROGRAM.
This appears when recording, E-E display, essence
mark recording, or sub clip addition for quick scene
selection is attempted on a disc that needs to be
salvaged.
a)
COUNTER MODE IS SELECTED.
SET COUNTER SELECT MENU TO TC
OR UB.
This appears when CNTR SEL on the HOME page of
the function menu is set to “COUNTER”, and you try
to preset timecode or user bits.
CNT mode!
To use timecode or user bits, set CNTR SEL to “TC”
b)
TC EXTERNAL IS SELECTED.
SET TC INTERNAL MODE IN FUNCTION function menu is set to “EXT”, and you try to preset
This appears when TCG on page P5 TC of the
TC EXT!
MENU.
timecode or user bits by setting PRST/RGN to
“PRESET”.
a)
TCG REGEN MODE IS SELECTED.
SET TC PRESET MODE IN FUNCTION
MENU.
This appears when PRST/RGN on page P5 TC of the
function menu is set to “TC” or “VITC”, and you try to
preset timecode or user bits.
REGEN mode!
a)
TCG RUN MODE IS SET TO REC RUN.
SET TC FREE RUN MODE IN FUNCTION the function menu is set to “REC RUN”, and you try to
This appears when RUN MODE on page P5 TC of
REC RUN!
MENU.
preset timecode or user bits.
b)
THUMBNAIL(S) CANNOT BE
DISPLAYED DURING RECORDING.
Stop recording and try again.
REC mode!
CANNOT EXECUTE IN REC MODE.
DRIVE MAINTENANCE MENU CANNOT
BE EXECUTED WHILE IN REC MODE.
INPUT SELECTION CANNOT BE
CHANGED DURING RECORDING.
AUDIO REC MODE CANNOT BE
CHANGED DURING RECORDING.
REC-PAUSE!
Disc Exchg!
TC/UB CANNOT BE PRESET IN REC-
PAUSE MODE.
Stop recording and try again.
EXIT DISC EXCHANGE CACHE MODE. This appears when you perform one of the following
operations.
• Attempt to preset timecode or user bits.
• Attempt to make a FAM connection.
• Press the button such as PLAY button while the
disc is being ejected during disc exchange.
b)
CLIP LIST IS NOT SELECTED.
This appears when you press the SUB CLIP/
DISC MENU button while the clip list on the disc is
not loaded into the current clip list.
No SEL List
b)
TO ADD AN ESSENCE MARK, EXIT
FROM SUB CLIP MODE FIRST.
This appears when an attempt is made to manipulate
the essence mark while the SUB CLIP/DISC MENU
indicator is lit or to set a clip flag while the clip list is
being played back (SUB CLIP indicator is lit). Perform
the operation after pressing the SUB CLIP/DISC
MENU button to turn it off.
SB CLP mode
b)
SUB CLIP IS INVALID.
SET APPROPRIATE IN/OUT POINTS.
Set the In and Out points again.
SUB CLIP NG
b)
NO CLIP LIST.
This appears when you try to delete a clip list when
there is no clip list saved on the disc.
Load the disc that contains the clip list you want to
delete.
No List!
160
Troubleshooting
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
Loading List!
LOADING CLIP LIST.
This appears if the SUB CLIP/DISC MENU button is
pressed while a clip list is loading.Wait for the clip list
to finish loading and try again.
b)
STOP ONCE, THEN EXECUTE.
This appears when the SUB CLIP/DISC MENU
button is pressed while the clip list is being played
back or when an attempt is made to open the GUI
screen with setup menu item 151 GUI OPERATION
set to “stop”. Perform the operation after stopping
playback.
STOP ONCE!
No EM space
ESSENCE MARK NOT RECORDED.
NO SPACE AVAILABLE TO RECORD
ESSENCE MARK.
Use the PDZ-1 Proxy Browsing Software to delete
unneeded essence marks.
Or, delete unneeded shot marks in the chapter
thumbnail screen.
EM Full!
NO MORE ESSENCE MARKS CAN BE
RECORDED.
Disc Damage
NON-AV Full
DISC CANNOT BE RECORDED TO.
USE ANOTHER DISC FOR RECORDING.
Use another disc.
DISC CANNOT BE RECORDED TO.
FOR MORE RECORDING SPACE,
DELETE NON-AV DATA. (GENERAL
FILES)
Delete unneeded GENERAL files.
Index File!
UNSUPPORT INDEX FILE.
DISC CANNOT BE RECORDED TO.
Use another disc.
File System
CURRENT VERSION OF THE
SOFTWARE SETS THE DISC WRITE
PROTECTED.
This appears when you insert a disc that can be
played back but not recorded.
Exchange the disc for one with a file system
supported by this unit. Or format the disc (see
FILE SYSTEM ON THE DISC INHIBITS
WRITING.
a)
LOADING.
This appears if you press a button while a disc is
loading. Wait until the disc has finished loading and
try again.
Loading!
a)
UNLOADING.
This appears if you press a button while a disc is
unloading.
Unloading!
Wait until the disc has finished unloading and try
again.
Clip lock!
File Access
Inhibit!
CLIP IS LOCKED.
UNLOCK CLIP IN THUMBNAIL MENU.
This appears when an operation is attempted on a
locked clip, or when an edit preset command is
received for such a clip. Use the Thumbnail Menu to
CANNOT CHANGE SETTINGS DURING This appears when an attempt is made to change the
FILE ACCESS.
setting of PC RMT (ENABLE/DISABLE) on page P7
OTHER of the function menu while accessing a file or
processing the command with PC REMOTE.
PC REMOTE IS DISABLED.
CHECK MAINTENANCE MENU M33.
This appears when an attempt is made to change the
setting of PC RMT (ENABLE/DISABLE) on page P7
OTHER of the function menu while maintenance
menu item M33: FILE I/F CONFIG >PC REMOTE is
set to “ENABLE”.
PC REMOTE IS DISABLED.
CHECK SETUP MENU 215.
This appears when an attempt is made to change the
setting of PC RMT (ENABLE/DISABLE) on page P7
OTHER of the function menu while setup menu item
215 i.LINK mode is set to the value other than “FAM”.
GUI Inhibit
GUI OPERATION IS INHIBITED.
CHECK SETUP MENU.
This appears when the THUMBNAIL button or the
DISC MENU (SHIFT+SUB CLIP) button is pressed
while setup menu item 151 GUI OPERATION is set to
“dis”.
161
Troubleshooting
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
Mixed REC!
THIS DISC CANNOT BE RECORDED.
TWO OR MORE AUDIO OR VIDEO
FORMATS ARE RECORDED ON THE
DISC.
This appears if a disc containing clips recorded in
different recording formats is inserted while mixed
format recording mode is disabled. Enable mixed
format recording mode, or insert another disc.
b)
DISC CANNOT BE EDITED.
MIXED AUDIO/VIDEO MODE ON DISC.
This appears when an edit preset command is
received, but the inserted disc contains clips with
mixed recording formats.
Mixed REC!
Exchange the inserted disc for a disc that does not
contain clips with mixed recording formats.
Resolution
THIS CLIP CANNOT BE ADDED.
THE CLIP’S RESOLUTION DOES NOT
Clips can be registered in clip lists only if their
resolution (number of system lines) matches the
MATCH THE CLIP LIST’S RESOLUTION. resolution of clips in the clip list.
b)
CANNOT EDIT AV MATERIAL WHEN
INPUT SIGNAL IS VIA i.LINK.
This appears when an edit preset command is
i.LINK!
received, but “i.LINK” is selected as the input signal.
Under V INPUT on the P1 VIDEO page of the
function menu, select a signal other than “i.LINK”.
b)
CANNOT EDIT AV MATERIAL WHEN
INPUT SIGNAL IS VIA SD-SDI.
This appears when an edit preset command is
received, but the recording format is set to HD422
and “SDSDI” is selected as the video input signal.
Under V INPUT on the P1 VIDEO page of the
function menu, select “HDSDI”.
SD Input!
b)
AUDIO INSERT EDITING WITH
INDEPENDENT CHANNELS IS NOT
POSSIBLE.
This appears when digital audio signals are set to
“data” and an edit preset command is received for
individual channels in the audio input channel pairs
(CH1/2, CH3/4, CH5/6, CH7/8). To perform insert
NON-AUDIO!
CHANGE ‘NON-AUDIO INPUT’ IN
MAINTENANCE MENU FROM ‘DATA’ TO editing of non-audio signals, always operate on
‘AUDIO’.
channel pairs.
If you want to perform insert editing of the audio of
individual channels from channel pairs, set
maintenance menu item M37: AUDIO CONFIG
>M372: NON-AUDIO INPUT to “audio”.
List Exists
DISC CANNOT BE EDITED.
DELETE ALL CLIP LIST BEFORE
BEGINNING DESTRUCTIVE EDITING.
This appears when an edit preset command is
received but the inserted disc contains a clip list.
Exchange the disc for one that does not contain a clip
list, or delete all clip lists from the disc.
b)
CANNOT EDIT AV MATERIAL.
CHECK REC FORMAT IN CLIP.
This appears when an edit preset command is
received for an HD420 clip or another clip that cannot
be edited.
N/A Clip!
Check the recording format of the edit target clip (see
b)
CANNOT EDIT AV MATERIAL.
CHANGE ‘SNGL CLIP PB’ TO ‘OFF’ AND received but the unit is in Single Clip Playback mode,
This appears when an edit preset command is
Mode Err!
‘REC MODE’ TO ‘NORMAL’ IN SETUP
MENU.
Disc Exchange Cache mode, or Clip Continuous Rec
mode.
Set setup menu item 154 SINGLE CLIP PLAY MODE
to “off”, or set setup menu item 150 REC MODE to
“normal”.
b)
DISC CANNOT BE EDITED.
USE PFD23A OR PFD50DLA.
This appears when an edit preset command is
received, but linear editing is not possible for the
inserted disc.
N/A Disc!
Insert a disc that can be edited by linear editing (see
a) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on”.
b) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on” or “limit”.
162
Troubleshooting
During recording and editing operations
Alarm message in time
data display area
Alarm message in video monitor screen Description/action
a)
VIDEO INPUT SIGNAL DOES NOT
MATCH SYSTEM SETUP.
This appears when the signal that does not
correspond to the system frequency or the number of
lines set in this unit is being input, or when HDSDI or
i.LINK TS is selected as a video input signal while
setting the SD signal recording.
Input Sig!”
Input a signal that matches the system frequency, or
change this unit’s system frequency setting (see
a)
ENCODING DOES NOT SYNCHRONIZE Check the signals being input to this unit.
WITH REF VIDEO.
ILL. REC!
a)
INPUT VIDEO SIGNAL DOES NOT
SYNCHRONIZE WITH REF VIDEO
SIGNAL.
Input a reference signal synchronized with this unit’s
system frequency.
ILL. REF!
USE COMMON REFERENCE SIGNAL
OR CONNECT RECORDER REF OUT TO
PLAYER REF IN.
a)
MEMORY FULL !!
Check the disc being recorded by this unit.
MEM. Full!
Verify ERR!
DISC ERROR DETECTED.
This appears when an error is found in the signal
recorded on the disc while performing the recording
verification function. Change the disc.
Recording
NOW RECORDING ...
Wait for recording to finish.
Cache Full!
CACHE FULL.
DATA IS BEING OVERWRITTEN.
This appears when the memory becomes full while
performing the disc exchange cache function.
Change the disc immediately.
Clip End!
Disc Full!
EDITING ACROSS MULTIPLE CLIPS IS
NOT POSSIBLE.
This appears when an edit across multiple clips is
attempted.
It is not possible to edit across multiple clips.
DISC FULL.
FOR MORE RECORDING, DELETE
SOME CLIPS.
This appears when the free capacity of the disc is
exhausted during assemble editing.
Delete unneeded clips, or exchange the disc for one
with enough free capacity.
a)
REC MODE SELECTION DIFFERENT
FROM AUDIO/VIDEO ON DISC.
MATCH REC MODE SELECTION WITH
CLIP.
This appears when editing of mixed recording formats
is enabled and an attempt is made to edit an
underlying clip in a different recording format.
Reset the recording format to match the format of the
REC Format!
a)
PREROLL TIME SETTING IS SHORT.
This appears when editing is impossible because the
preroll time is too short.
Preroll!
Set setup menu item 001 PREROLL TIME to 5
seconds or longer.
a)
ASSEMBLE EDITING IS NOT POSSIBLE This appears when an attempt is made to perform an
Last Clip!
BESIDES LAST CLIP.
assemble edit on a clip that is not the last clip on the
disc.
Assemble editing is possible only on the last clip.
a) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on” or “limit”.
During playback
Alarm message in time data
display section
Alarm message in monitor video
section
Description/action
a)
ILLEGAL PLAYBACK.
Check the disc being played by this unit.
Check the disc being played by this unit.
Use another disc.
ILL. PLAY!
a)
MEMORY EMPTY !!
MEM. Empty!
Disc Error!
DISC ERROR DETECTED.
163
Troubleshooting
a) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on” or “limit”.
During thumbnail search, scene selection, and clip list operations
Alarm message in GUI
screen
Description/action
Cannot Expand Clip any
Further.
The clip cannot be expanded into more blocks.
This appears when the EXPAND button is pressed when the number of block is maximum, or
when the duration of an expanded thumbnail is 1 frame.
Selected Essence Mark does The selected essence mark does not exist.
not Exist.
This appears in the essence mark selection screen when the specified essence mark does not
exist on the disc.
Sub Clip is Invalid.
Set Appropriate IN/OUT
Points.
The temporal relationship between the specified In and Out points in sub clip trimming is not
correct.
Reset so that the value of the Out point timecode is larger than the value of the In point
timecode.
Duration of One Clip List
The total duration of the current clip list is greater than 24 hours.
must be Less than 24 Hours. This appears when the total duration of the current clip list exceeds the upper limit of 24 hours as
the result of adding or trimming sub clups.
No More Sub Clips can be
Added to the Clip List.
The upper limit of sub clips in the current clip list has been reached.
This appears when the upper limit of 300 clips in a clip list has been reached as the result of
adding or trimming sub clips.
Sub Clip does not Exist.
Clip List does not Exist.
There are no sub clips in the current clip list.
This appears when an attempt is made to move, trim or delete sub clips or preset timecode.
There are no clip lists on the disc.
This appears when an attempt is made to execute a Delete Clip List operation when there are no
clip lists on the disc.
Move is Invalid.
The sub clip cannot be moved.
This appear when an attempt is made to execute a Move Sub Clips operation when there are no
sub clip in the current clip list, or when there is only one sub clip.
Chapter does not Exist.
The specified chapter has not been recorded.
This appears when an attempt is made to display a chapter when a chapter has not been
recorded for that clip.
Some Essence Mark cannot The essence mark cannot be deleted.
be Deleted. This appears when an attempt is made to delete an essence mark that cannot be deleted with a
Delete Essence Mark operation. Rec Start and Cut essence marks cannot be deleted.
Some Essence Mark cannot The essence mark cannot be moved.
be Moved.
This appears when an attempt is made to move an essence mark that cannot be moved with a
Move Essence Mark operation. Rec Start and Cut essence marks cannot be moved.
Clip is Locked.
The clip is locked.
This appears when an attempt is made to delete a clip, set the clip thumbnail, or delete a shot
mark when the clip is locked.
All Clips are Locked.
All Clips are Unlocked.
Command Disabled.
All clips are locked.
This appears when an attempt is made to execute a Lock All Clips operation when all clips are
already locked.
All clips are unlocked.
This appears when an attempt is made to execute an Unlock All Clips operation when all clips
are already unlocked.
This appears when an attempt is made to perform Format Disc operation while Disable “Format
Disc” is set to “Disable”.
A File with the Name you
Specified Already Exists.
Specify a Different Name.
This appears when an attempt is made to set an existing clip name while changing the clip name
using Set Clip Name.
Set NAMING FORM to “free” This appears when an attempt is made to change the clip name using Set Clip Name even
“No Flash Drive”
This appears when an attempt is made to select “USB Flash Drive” in the media selection
screen under Load Planning Metadata/Select Drive even though the USB memory is not
connected.
164
Troubleshooting
Alarm message in GUI
screen
Description/action
Not Loaded.
This appears when a command related to planning metadata is executed with no planning
metadata loaded.
Load planning metadata and try again.
Syntax Error!
This appears when loading of planning metadata fails because of a syntax error. Correct the
syntax error and try loading the metadata again.
Irregular Disc is Used.
Use Professional Disc.
This appears when the unit is unable to record or play the inserted disc.
This unit can record and play Professional Discs. Insert a Professional Disc.
The Disc Write Protect TAB
is set to Save.
This appears when an attempt is made to format a write-protected disc.
Try formatting the disc after moving the write protect tab away from the Save position.
The REC Inhibit Mode is
Selected.
Check Function Menu.
This appears when an attempt was made to format when function menu item HOME >F3: REC
INH is set to “ON”.
Set F3: REC INH to “OFF” and try formatting again.
Auto Formatting was not
Completed.
This appears when auto formatting fails.
Video Resolution Differ from This appears when an attempt is made to add a clip to a clip list containing clips with a different
it on Clip List.
video resolution (number of system lines).
It is not possible to add clips to clip lists containing clips with a different video resolution.
No Clip Meets the Condition. This appears when no clip is found to meet clip filtering conditions.
Alarms relating to audio and video signals
Alarm message in time
data display area
Alarm message in video monitor screen Action
a)
INPUT VIDEO IS NOT DETECTED.
CHECK THE VIDEO INPUT MODE AND
SUPPLY A VIDEO SIGNAL TO VIDEO
INPUT.
• Check the setting of V INPUT on Page P1 VIDEO of
• Input an HDSDI signal.
No INPUT!
a)
INPUT AUDIO EMPHASIS IS NOT
SUPPORTED.
CHECK THE EMPHASIS OF THE AUDIO
INPUT SIGNAL.
Check the emphasis of the audio input signal.
Input a standard signal.
EMPHASIS!
REF NON-STD
A NON-STANDARD REF SIGNAL IS
BEING USED FOR REF VIDEO. USE A
STANDARD SIGNAL.
a) Displayed only when setup menu item 016 ALARM DISPLAY is set to
“on”.
Alarms relating to sensors and drives
Alarm message in time
data display area
Alarm message in video monitor acreen Description/action
FAN Stopped
DR-FAN Stop
N-FAN Stop
FAN MOTOR STOPPED.
Contact a Sony service representative.
Note
DRIVE FAN MOTOR STOPPED.
The unit will not stop operating, but if you continue to
use it in this state temperatures inside the unit or the
drive will rise, possibly resulting in failure or fire.
FAN MOTOR ON NET-4 BOARD
STOPPED.
High TEMP!
HIGH TEMPERATURE.
HIGH TEMPERATURE IN DRIVE.
HIGH TEMPERATURE ON NET-4 BOARD.
MOISTURE HAS BEEN DETECTED.
HUMID!
Stop recording or playback, power the unit off and on
again, and wait until the HUMID display disappears.
BATT EMPTY!
BATTERY EMPTY!
Change the battery.
165
Troubleshooting
Alarm message in time
data display area
Alarm message in video monitor acreen Description/action
UNKNOWN USB DEVICE. The USB connector of this unit is for maintenance
Unknown USB
purposes and connection of USB devices. Connect a
compatible USB device.
Alarms related to system frequency and recording format
The following alarms are displayed only when setup menu
item 016 ALARM DISPLAY is set to “on” or “limit”.
Alarm message in time
data display area
Alarm message in video monitor screen Action
1080/59.94i
1080/29.97P
1080/50i
RECORDING AND PLAYBACK IS NOT
POSSIBLE.
SYSTEM SETTINGS DIFFERENT FROM the same system frequency as the unit, or change the
This appears when the system frequency of the unit
differs from that of the loaded disc. Insert a disc with
DISC.
unit’s system frequency.
1080/25P
1080/23.98P
720/59.94P
720/50P
525/59.94i
625/50i
1080/59.94i
1080/50i
DISC CANNOT BE RECORDED.
VIDEO RESOLUTION DIFFER FROM IT disabled and the current system lines setting of this
ON DISC.
This appears when mixed format recording mode is
unit does not match the resolution of the inserted
disc.
Insert a disc with a resolution that matches the
current system lines setting of this unit, or change the
system lines setting of this unit, or enable mixed
format recording mode.
1080/29.97P
1080/25P
1080/23.98P
720/59.94P
720/50P
HD422 1080
HD422 720
HD420 1080
HD420 720
IMX50 Clip
IMX40 Clip
IMX30 Clip
8CH×16 Clip
4CH×24 Clip
2CH×16 Clip
DISC CANNOT BE RECORDED.
VIDEO REC MODE SELECTION
DIFFERENT FROM VIDEO ON DISC.
This appears when mixed format recording mode is
disabled, and the video recording format of this unit
does not match the video recording format of the
inserted disc.
Insert a disc with a video recording format that
matches the video recording format of this unit, or
change the video recording format of this unit.
DISC CANNOT BE RECORDED.
AUDIO REC MODE SELECTION
DIFFERENT FROM AUDIO ON DISC.
This appears when mixed format recording mode is
disabled, and the audio recording format of this unit
does not match the audio recording format of the
inserted disc.
Insert a disc with a audio recording format that
matches the audio recording format of this unit, or
change the audio recording format of this unit.
166
Troubleshooting
Error messages
Specifications
Error codes appear in the time data display when an error
(usually a hardware problem) occurs. In addition, both
error messages and error codes appear in the monitor video
section and on the video monitor connected to the unit.
When an error message appears, follow the instructions in
the error message to resolve the problem.
General
External dimensions (w/h/d, excluding projections)
1
3
5
210×132×396 mm (8 / ×5 / ×15 /
8
4
8
inches)
Error code
E r r o r 5 0 - 0 1 0
Error code in time data display area
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
50-010
PRESS EJECT KEY
TO EJECT DISC.
Error code
Example error in video monitor screen
3
210 (8 / )
in mm (inches)
8
Mass
6.5 kg (14 lb. 5 oz.)
Power requirements
To eject discs with the unit powered
off
100 V to 240 V AC, 50/60 Hz
12 V DC
Power consumption
As an emergency measure, disc cartridges can be removed
with the unit powered off. This operation should always be
done by a trained service technician.
AC operation: 80 W
DC operation: 65 W
(Power saving mode: 55 W)
Peak inrush current
(1) Power ON, current probe method:
45 A (240 V), 18 A (100 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1: 11 A
(230 V)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage temperature
–20ºC to +60ºC (–4ºF to +140ºF)
Operating relative humidity
25 to 90%
System
Recording/playback format
Video
Proxy video
MPEG HD 422: 50 Mbps
MPEG-4
167
Specifications
Audio
Proxy audio
24 bits, 48 kHz, 8 channels
A-law 8 bits, 8 kHz, 8 channels
Input connectors
Digital video inputs
SD/HDSDI INPUT
Recording/playback times
PFD23A discs Approx. 43 minutes
PFD50DLA discs
BNC type (×1), complying with SMPTE-
259M (SD)/SMPTE-292M (HD)
Approx. 95 minutes
(i.LINK) S400
6-pin type (×1), complying with IEEE
1394
Note
The recording and playback times listed above are
approximate. Maximum recording times may vary
depending on recording conditions.
Analog video inputs
REF.VIDEO INPUT
BNC type (×2, loop-through), HD Tri-
level sync (0.6 Vp-p/75 Ω/sync
negative), SD black burst, or SD
composite sync (0.286 Vp-p/75 Ω/
sync negative)
Search speed
Jog mode
Variable-speed mode
–2 to +2 times normal speed
–1 to +1 times normal speed
Shuttle mode –20 to +20 times normal speed
Fast forward mode
+35 times normal speed
Fast reverse mode
Analog audio inputs
ANALOG AUDIO INPUT 1, 2
XLR 3-pin, female (×2), +4 dBu, high
impedance, balanced
–35 times normal speed
Digital audio inputs
DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4
BNC type (×2), 1/2ch, 3/4ch complying
with AES-3id-1995
Video performance
Sampling frequency
Y: 74.25 MHz, R–Y/B–Y: 37.125 MHz
8 bits/sample
Compression MPEG-2 422P@HL
Timecode input
TIME CODE IN
Quantization
BNC type (×1), SMPTE timecode, 0.5 to
18 Vp-p, 10 kΩ, unbalanced
Composite output
Frequency response
0.5 to 5.75 MHz+0.5/–2.0 dB
53 dB or more
20 ns or less
Output connectors
S/N (Y)
Y/C delay
Digital video outputs
HDSDI OUTPUT 1, 2(SUPER)
K-factor (K2T) 1.0% or less
BNC type (×2), complying with SMPTE-
292M
Processor adjustment range
SDSDI OUTPUT 1, 2(SUPER)
Video level
Chroma level –∞ to +3 dB
–∞ to +3 dB
BNC type (×2), complying with SMPTE-
259M
Set up/black level
30 IRE/ 210 mV
30°
Analog video outputs
COMPOSITE OUTPUT 1, 2(SUPER)
Chroma phase
System phase SYNC: 15 µs
SC: 0 to +400 ns
BNC type (×2), 1.0 Vp-p, 75 Ω, sync
negative, complying with SMPTE-
170M
Audio performance
Sampling frequency
48 kHz
Analog audio outputs
ANALOG AUDIO OUTPUT 1, 2
XLR 3-pin, male (×2), +4 dBu, 600 Ω,
low impedance, balanced
AUDIO MONITOR
Quantization
Headroom
24 bits
–20/–18/–16/–12 dB (selectable)
XLR 3-pin, male (×2), +4 dBu, 600 Ω,
Frequency response
20 Hz to 20 kHz +0.5/–1.0 dB (0 dB at
low impedance, balanced
PHONES
Stereo phone jack (×1), –∞ to –13 dBu,
8 Ω, unbalanced
1 kHz)
Dynamic range 90 dB or more
Distortion
0.05% or less (at 1 kHz)
168
Specifications
Digital audio outputs
BKP-L551 Battery Adaptor
MPEG TS Board
DIGITAL AUDIO (AES/EBU) OUTPUT 1/2, 3/4
BNC type (×2), 1/2 ch, 3/4 ch complying
with AES-3id-1995
PDBK-201
HD1500
SD Record And Playback Key
PDBK-S1500
24P Record And Playback Key
PDBK-F1500
Timecode output
TIME CODE OUT
BNC type (×1), SMPTE timecode,
1.0 Vp-p, 75 Ω, unbalanced
Design and specifications are subject to change without
notice.
Remote control connectors
REMOTE(9P) D-sub 9-pin, female (×1), complying
with RS-422A
Notes
VIDEO CONTROL
• Always make a test recording, and verify that it was
recorded successfully. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF FAILURE OF THIS UNIT OR ITS
RECORDING MEDIA, EXTERNAL STORAGE
SYSTEMS OR ANY OTHER MEDIA OR
STORAGE SYSTEMS TO RECORD CONTENT
OF ANY TYPE.
D-sub 9-pin, female (×1), complying
with EIA RS-423
4-pin, female (×1)
DC 12 V, 7.5 W
RJ-45 type (×1)
1000BASE-T: complying with
IEEE802.3ab
100BASE-TX: complying with
IEEE802.3u
REMOTE
Network
10BASE-T: complying with IEEE802.3
• Always verify that the unit is operating properly
before use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE
LOSS OF PRESENT OR PROSPECTIVE PROFITS
DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
Other
MAINTENANCE connectors
(High Speed USB (USB 2.0) Type-A)
Accessories supplied
Operation manuals
English version (1)
Japanese version (1)
CD-ROM manual (1)
Installation manual (1)
XDCAM Application Software CD-ROM (1)
Connector caps
Accessories not supplied
AC power cord
• For the customers in the U.S.A and Canada
Part number 1-551-812-41 (125 V, 10 A, about 2.4 m)
• For the customers in the United Kingdom
Part number 1-777-823-12 (250 V, 10 A, about 2.0 m)
• For the customers in European countries other than the
United Kingdom
Part number 1-551-631-61 (250 V, 10 A, about 2.0 m)
RCC-G5 9-pin Remote Control Cable
RM-280 Remote Edit Controller
PFD23A Professional Disc
PFD50DLA Dual-layer Professional Disc
BP-L80S Battery Pack
BP-GL95 Battery Pack
169
Specifications
Using PDZ-1 Proxy
Browsing Software
When a computer with the PDZ-1 Proxy Browsing
Software installed is connected to this unit, you can
transfer the proxy AV data and metadata files recorded on
a disc to the computer. On the computer side, PDZ-1
enables you to browse the proxy AV data, add or modify
metadata (titles, comments, essence marks, etc.), or create
a clip list.
The modified metadata and the created clip list can then be
written back to the disc loaded in this unit.
For more information about PDZ-1 functions and
operations, refer to the PDZ-1 help.
System requirements
The following are required to use PDZ-1.
• Computer: PC with Intel Pentium M processor, at least 1
GHz (installed memory: at least 512 MB)
• Operating system: Microsoft Windows XP Professional
SP2 or higher, Windows Vista Ultimate/Business
(32 bit)
• Web browser: Internet Explorer 6.0 SP1 or higher
• DirectX: DirectX 8.1b or higher
To install PDZ-1
Insert the supplied XDCAM Application Software CD-
ROM into the CD-ROM drive of your computer, and then
run the installer in the PDZ-1 directory of the CD-ROM.
For details, refer to the ReadMe file contained on the
CDROM disc.
Notes
• Make sure that the hard disk drive on which the work
folder to store the material transferred from this unit has
adequate free space.
• To transfer files between the computer and this unit
requires this unit’s IP address and other network-related
settings to be made.
For details of the network-related settings, see “To change
170
Using PDZ-1 Proxy Browsing Software
Using UMID Data
Metadata is additional information recorded on discs along
with audio-visual data. It is used to bring greater efficiency
to the flow of operations from material acquisition through
editing, and to make it easier to find and reuse material.
As one of application of metadata, the UMID has been
internationally standardized.
What is a UMID?
A UMID (Unique Material Identifier) is a unique i-
dentifier for audio-visual material defined by the
SMPTE-330M-2003 standard.
A UMID may be either as a 32-byte Basic UMID or an
Extended UMID, which includes an additional 32 bytes of
Source Pack to make a total 64 bytes.
For details, refer to SMPTE-330M.
Extended UMID (64 bytes)
Basic UMID (32 bytes)
Instance
Source Pack (32 bytes)
Spatial
Coordinates
Time/Date
8 bytes
Universal label
12 bytes
L
Material Number
Country Org
User
No.
4 bytes 4 bytes 4 bytes
1
16 bytes
3 bytes
12 bytes
A globally unique ID is automatically recorded for every
clip.
The Extended UMID is metadata that provides additional
information such as location, time/date, company ID and
so on.
The UMID is applied as follows.
Material No.
ID generated when
shooting
Source Pack
Shooting
information (when,
where and who)
Same as the above
Instance No.
Same as the above
Original material: 00 00 00
Copied material: generation number (1 byte)
+ random number (2 bytes)
Distinguish between the
original material and copied
material
Material source ID/
detecting material
Metadata pack that
identifies the source of
material unit by defining the
when, where and who of
the material unit with which
it is associated.
Using the Extended UMID
Functions of UMID data
UMID data enables the following:
• Addition of a globally unique ID to every clip of audio-
visual material. The unique ID is used to detect the
material source and to link it with the original source
material.
You have to enter a country code, organization code and
user code. Set the country code referring to the table in ISO
3166, and set the organization code and user code
according to the guidelines of your organization.
For details, see “Setting UMID ownership information”
• Distinguishing between original material and copied
material. 00 is added to the Instance Number for original
material.
171
Using UMID Data
• Recording with UTC time. UTC (coordinated universal
time) is used when recording the UMID. Use of a
universal time system enables uniform management of
source material recorded all over the world.
• Calculation of date differences. Source material is
recorded using modified Julian dates (MJD), which
enables easy calculation of date differences between
different source material items.
About the UMID ownership information
COUNTRY (country code)
Set the country code by entering an abbreviated
alphanumeric string (4-byte alphanumeric string)
according to the values defined in ISO 3166-1.
There are about 240 country codes.
Find your own country code on the following web page.
Refer to ISO 3166-1:
http://www.iso.org/iso/country-codes/
iso_3166_code_lists.htm
Setting UMID ownership information
Proceed as follows.
1
Set setup menu item 029 STORE OWNER to “on”
When the country code is less than 4 bytes, the active part
of the code occupies the first part of the 4 bytes and the
remainder must be filled with the space character (20h).
operations.
Example: Japan
For Japan, the country code is JP, which is 2 bytes, or JPN,
which is 3 bytes.
Thus, enter the following:
The STORED OWNERSHIP (UMID ownership
information setting) screen appears.
JP_ _
RETURN
or
ITEM-029
SELECT
JPN _
STORED OWNERSHIP
where _ represents a space.
*COUNTRY
ORGANIZATION
USER
-
-
-
ORGANIZATION (organization code)
Enter a 4-byte alphanumeric string for the organization
code.
SAVE
EXIT
SETUP
Notes
COUNTRY: Sets the country code.
ORGANIZATION: Sets the organization code.
USER: Sets the user code
• There are no problems in recording or playing back
audio-video signals, even if the ORGANIZATION is not
set.
• Organization codes must be acquired by applying to the
SMPTE registration office. When no organization code
has been acquired, it is forbidden to enter an arbitrary
string. As a rule, the code “00” must be entered.
Freelance operators who do not belong to an origination
should enter “~”.
See the next item “About the UMID ownership
information” for more information about these codes.
2
3
Use the PUSH SET(S.SEL) knob to select the item to
set and the character input location, then press the
knob.
USER (user code)
Use the PUSH SET(S.SEL) knob, – or + function
button (F3 or F4) to select characters to input at the
selected location.
Enter a 4-byte alphanumeric string to identify the user.
The user code is registered with each organization locally.
It is usually not centrally registered.
When the user code is less than 4 bytes, enter the user code
at the beginning of the 4 bytes and fill the remainder of the
string with the space character (20h).
To delete all input data
Press the RESET/RETURN button.
This user code is determined by the organization. The
methods used depend on the organization.
4
Press SAVE function button (F5).
The message “NOW SAVING...” appears, and the
ownership information is saved.
Note
User code cannot be entered when no organization code
has been entered.
172
Using UMID Data
Ancillary data in MXF files
Ancillary Data
VANC ancillary data recorded from a HDSDI signal can
be inserted to an MXF file as an ANC Frame Element
(conforming to the SMPTE436M-2006) and can be output.
This data can also be input and recorded on the disc.
This unit can play and record ancillary data multiplexed
into HDSDI signals. It can also input and output ancillary
data in MXF files when transferring files via FAM or FTP
connections. Transferable auxiliary data includes text data
(captions and metadata) and control signals.
To insert ancillary data into MXF files to
output
In setup menu item 666 METADATA ITEM OUT, select
Ancillary data in HDSDI signals
This unit can record and play back closed captions
HANC/VANC packets
1)
conforming to the EIA-708-B standard and text data
2)
conforming to the ARIB TRB23 which comprise the
Detection of HANC/VANC packets
VANC (Vertical ancillary data) packets.
HANC/VANC packets are recorded on the disc only when
the DATA ITEM of the head frame is identified as ANC
Frame Elements conforming to the SMPTE436M-2006
when an MXF file is input.
1) EIA: Electronic Industries Alliance
2) ARIB: Association of Radio Industries and Businesses
To record ancillary data
In maintenance menu item M3B: VANC RX
General MXF metadata
PARAMETER, set the lines where ancillary data is
inserted, the DID (Data Identifier word), and the SDID
This unit examines the data contained in the header
1)
metadata area when an MXF file is input. If the data is
identified as the data created by the device other than
XDCAM at this time, one file (KLVE file) is created.
To record EIA-608-B standard closed caption
signals in SDSDI signals after conversion to the
EIA-708-B standard
1) The header metadata area contains the metadata information about the
entire file. See SMPTE377M for details.
Set the following items.
• Sub items of maintenance menu item M3B: VANC RX
PARAMETER
For details, see “Directory structure” (page 104) and
- DID (data identification word): 61h
- SDID (secondary data identification word): 01h
• V INPUT on function menu page P1 VIDEO: SDSDI
• Setup menu item 031 RECORDING FORMAT: HD422,
420HQ, or 420SP
VANC packets
• The Japanese ARIB TR-B23 standard limits the number
of packets that can be multiplexed into HDSDI to 4
packets per line.
• The number of VANC packets that can be recorded that
is set using maintenance menu item M3B is limited to 9
packets per frame for 50P or 59.94P mode and 18
packets per frame for other modes.
• When VANC packets are not continuous from word 0,
and there is unused area on the line, then information
about the packet position is not recorded. Packets are
output flush left.
• During input, if a parity error is detected in a VANC
packet, the packet is discarded and recorded flush left.
173
Ancillary Data
Setting item of
HKDV-900
Menu item of this unit’s setup
menu
Correspondencebetween
Setting Items of the
HKDV-900 and Setup
Menu of This Unit
FREQUENCY
939: H DETAIL FREQUENCY (DC)/
958: H DETAIL FREQUENCY (UC)
b)
H/V RATIO
940: H/V RATIO (DC)/
b)
959: H/V RATIO (UC)
GAMMA
CROP
No menu item corresponds to this setting
item.
930: DOWN CONVERTER MODE/
b)
950: UP CONVERTER MODE
Setting item of
HKDV-900
Menu item of this unit’s setup
menu
LETTER BOX
SQUEEZE
930: DOWN CONVERTER MODE/
b)
950: UP CONVERTER MODE
a)
HD Master
HD Y
740: MASTER LEVEL (HD)
930: DOWN CONVERTER MODE/
a)
b)
741: Y LEVEL (HD)
950: UP CONVERTER MODE
a)
HD Pb
742: Pb LEVEL (HD)
a) The setting becomes effective for the output only when VID. PROC on
page P1 VIDEO of the function menu is set to “MENU”.
a)
HD Pr
743: Pr LEVEL (HD)
b) Whether to set the down-converter or up-converter is determined using
setup menu item 212 VIDEO REMOTE CONTROL SELECT. If both
converters are selected (“u & d” of menu item 212), the relevant menu item
allows both converters to be set, but only the value for the down-converter
is used as the return value from this unit and the unity value.
a)
HD Setup
HD Sync Phase
HD Fine
745: SETUP LEVEL (HD)
a)
746: SYNC PHASE (HD/UC)
a)
747: FINE (HD/UC)
Meaning of abbreviations within parentheses in
the table
HD: HDSDI output during playback of HD format video
DC: Down-conversion output to SD (D1 SDI/
COMPOSITE) during playback of HD format video
SD: SD (D1 SDI/COMPOSITE) output during playback
of SD format video
D1 Master
No menu item corresponds to this setting
item.
D1 Y
No menu item corresponds to this setting
item.
D1 B-Y
D1 R-Y
D2 VIDEO
No menu item corresponds to this setting
item.
UC: Up-conversion output to HDSDI during playback of
SD format video
No menu item corresponds to this setting
item.
715: VIDEO GAIN CONTROL (HD/DC/
a)
SD/UC)
D2 CHROMA
D2 HUE
716: CHROMA GAIN CONTROL (HD/
DC/SD/UC)
a)
717: CHROMA PHASE CONTROL (HD/
a)
DC/SD/UC)
SETUP
718: SETUP LEVEL/BLACK LEVEL (HD/
DC/SD/UC)
a)
SD Sync Phase 719: SYSTEM PHASE SYNC (DC/SD)
SD Fine 720: SYSTEM PHASE SC (DC/SD)
CROSS COLOR 934: CROSS COLOR (DC)
H CROP
POSITION
932: H CROP POSITION (DC)/
951: H CROP POSITION (UC)
b)
DETAIL GAIN
935: DETAIL GAIN (DC)/
954: DETAIL GAIN (UC)
b)
b)
LIMITTER
CRISP
936: LIMITER (DC)/955: LIMITER (UC)
937: CRISP (DC)/
956: CRISP THRESHOLD (UC)
b)
DEPEND
938: LEVEL DEPEND THRESHOLD
(DC)/
957: LEVEL DEPEND THRESHOLD
b)
(UC)
174
Correspondence between Setting Items of the HKDV-900 and Setup Menu of This Unit
List of Supported USB Keyboards
Select the corresponding language by selecting Settings
>Select USB Keyboard Language in the Disc Menu (see
When the area of use is set to “UC” and
1)
the font setting is “European Alphabet”
On this unit, you can enter any of the characters and
symbols supported by the keyboards listed below.
1) When the font setting is “Simplified Chinese” or “Traditional Chinese”, a
keyboard with the same layout as the English [United States] keyboard is
selected automatically.
English [United Kingdom]
English [United States]
French [France]
German [Germany]
175
List of Supported USB Keyboards
Italian [Italy]
Polish (Programmers) [Poland]
Russian [Russia]
Spanish [Spain]
When the area of use is set to “UC” and
the font setting is “Korean”
The keyboard is fixed as the Korean keyboard, and you can
enter Hangul characters.
Note
The keyboard language cannot be changed.
176
List of Supported USB Keyboards
When the area of use is set to “J”
Notes
The keyboard is fixed as the Japanese keyboard.
• The keyboard language cannot be changed.
• It is not possible to enter Japanese hiragana, katakana,
and kanji.
177
List of Supported USB Keyboards
About IJG (Independent JPEG
Group)
Trademarks and Licenses
This software is based in part on the work of the
Independent JPEG Group.
MPEG-4 visual patent portfolio
license
Character display software “iType”
THIS PRODUCT IS LICENSED UNDER THE MPEG-4
VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A
CONSUMER FOR
This product includes technology from Monotype Imaging
®
Inc., including iType and certain fonts.
(i) ENCODING VIDEO IN COMPLIANCE WITH THE
MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”)
AND/OR
About net-snmpd
(ii) DECODING MPEG-4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE
MPEG-4 VIDEO.
---- Part 1: CMU/UCD copyright notice: (BSD like) -----
Copyright 1989, 1991, 1992 by Carnegie Mellon
University
Derivative Work - 1996, 1998-2000
NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL
Copyright 1996, 1998-2000 The Regents of the University
of California
INFORMATION INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND COMMERCIAL
USES AND LICENSING MAY BE OBTAINED FROM
MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM
All Rights Reserved
Permission to use, copy, modify and distribute this
software and its documentation for any purpose and
without fee is hereby granted, provided that the above
copyright notice appears in all copies and that both that
copyright notice and this permission notice appear in
supporting documentation, and that the name of CMU and
The Regents of the University of California not be used in
advertising or publicity pertaining to distribution of the
software without specific written permission.
MPEG LA is offering licenses for (i) manufacturing/sales of any storage
media storing MPEG-4 Visual video information (ii) distribution/
broadcasting of MPEG-4 Visual video information in any manner (such as
online video distribution service, internet broadcasting, TV broadcasting).
Other usage of this product may be required to obtain license from
MPEGLA. Please contact MPEG LA for any further information. MPEG LA,
L.L.C., 250 STEELE STREET, SUITE 300, DENVER, COLORADO
80206, http://www.mpegla.com
CMU AND THE REGENTS OF THE UNIVERSITY OF
CALIFORNIA DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS. IN NO EVENT SHALL CMU OR THE
REGENTS OF THE UNIVERSITY OF CALIFORNIA
BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM THE LOSS OF
USE, DATA OR PROFITS, WHETHER IN AN ACTION
OF CONTRACT, NEGLIGENCE OR OTHER
MPEG-2 video patent portfolio
license
ANY USE OF THIS PRODUCT OTHER THAN
CONSUMER PERSONAL USE IN ANY MANNER
THAT COMPLIES WITH THE MPEG-2 STANDARD
FOR ENCODING VIDEO INFORMATION FOR
PACKAGED MEDIA IS EXPRESSLY PROHIBITED
WITHOUT A LICENSE UNDER APPLICABLE
PATENTS IN THE MPEG-2 PATENT PORTFOLIO,
WHICH LICENSE IS AVAILABLE FROM MPEG LA,
L.L.C., 250 STEELE STREET, SUITE 300, DENVER,
COLORADO 80206.
TORTIOUS ACTION, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE
OF THIS SOFTWARE.
“PACKAGED MEDIA” means any storage media storing MPEG-2 video
information such as DVD movie which are sold/distributed to general
consumers. Disc replicators or sellers of the PACKAGED MEDIA need to
obtain licenses for their own business from MPEG LA. Please contact MPEG
LA for any further information. MPEG LA, L.L.C., 250 STEELE STREET,
SUITE 300, DENVER, COLORADO 80206
---- Part 2: Networks Associates Technology, Inc
copyright notice (BSD) -----
http://www.mpegla.com
178
Trademarks and Licenses
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
Copyright (c) 2001-2003, Networks Associates
Technology, Inc
All rights reserved.
• The name of Cambridge Broadband Ltd. may not be
used to endorse or promote products derived from this
software without specific prior written permission.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of the Networks Associates
Technology, Inc nor the names of its contributors may be
used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDER ``AS IS'' AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS
IS'' AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDERS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
---- Part 4: Sun Microsystems, Inc. copyright notice (BSD)
-----
Copyright ÅE2003 Sun Microsystems, Inc., 4150 Network
Circle, Santa Clara, California 95054, U.S.A. All rights
reserved.
Use is subject to license terms below.
This distribution may include materials developed by third
parties.
POSSIBILITY OF SUCH DAMAGE.
---- Part 3: Cambridge Broadband Ltd. copyright notice
(BSD) -----
Sun, Sun Microsystems, the Sun logo and Solaris are
trademarks or registered trademarks of Sun Microsystems,
Inc. in the U.S. and other countries.
Portions of this code are copyright (c) 2001-2003,
Cambridge Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
179
Trademarks and Licenses
OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
• Neither the name of the Sun Microsystems, Inc. nor the
names of its contributors may be used to endorse or
promote products derived from this software without
specific prior written permission.
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS
IS'' AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDERS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
---- Part 6: Cisco/BUPTNIC copyright notice (BSD) -----
Copyright (c) 2004, Cisco, Inc and Information Network
Center of Beijing University of Posts and
Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
POSSIBILITY OF SUCH DAMAGE.
---- Part 5: Sparta, Inc copyright notice (BSD) -----
• Neither the name of Cisco, Inc, Beijing University of
Posts and Telecommunications, nor the names of their
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
Copyright (c) 2003-2006, Sparta, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS
IS'' AND ANY EXPRESS OR IMPLIED
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of Sparta, Inc nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDERS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS
IS'' AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDERS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
POSSIBILITY OF SUCH DAMAGE.
180
Trademarks and Licenses
---- Part 7: Fabasoft R&D Software GmbH & Co KG
copyright notice (BSD) -----
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
Copyright (c) Fabasoft R&D Software GmbH & Co KG,
2003
oss@fabasoft.com
• Neither name of Intel Corporation nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
Author: Bernhard Penz <bernhard.penz@fabasoft.com>
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS
IS'' AND ANY EXPRESS OR IMPLIED
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• The name of Fabasoft R&D Software GmbH & Co KG
or any of its subsidiaries, brand or product names may
not be used to endorse or promote products derived from
this software without specific prior written permission.
WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL INTEL OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDER ``AS IS'' AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
About libupnp
Copyright (c) 2000-2003 Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
181
Trademarks and Licenses
For more efficient searches,
XDCAM equipment records essence
marks as part of Non-RealTime
metadata, and uses them to display
thumbnails.
automatically whenever high-
resolution MPEG HD data is
recorded.
Glossary
Reference video signal
AES/EBU
A video signal that contains a sync
signal or sync and burst signals, used
as a reference for synchronization of
video equipment.
A standard established jointly by the
AES (Audio Engineering Society)
and EBU (European Broadcasting
Union) for serial transmission of
digital audio. Two channels of audio
can be transmitted via a single
connector.
HD tri-level sync
An HDTV analog reference signal
that applies to 59.94/50Hz systems.
A sync signal defined in SMPTE-
274M with positive, negative, and
zero values.
SDSDI signal
SD Serial Digital Interface. An
interface standardized as SMPTE-
259M which enables the
transmission of an uncompressed
digital component stream.
HDSDI signal
Abbreviation of HD Serial Digital
Interface.
A signal in the HDTV serial interface
defined by SMPTE-292M.
Clip
A recording unit. Clips are created
every time recording starts and stops.
S/N
Clip list
Signal-to-Noise ratio. The relation of
the strength of the desired signal to
the accompanying electronic
interference, the noise. If S/N is high,
sounds are reproduced with less noise
and pictures are reproduced clearly
without snow.
A list of locations in the material
recorded on the disc, arranged in any
order. Clip lists can be created with
the scene selection function of this
unit, and with the PDZ-1 Proxy
Browsing Software.
Metadata
Information about the properties of
video and audio content. XDCAM
records metadata such as UMIDs and
essence marks, and the PDZ-1 Proxy
Browsing Software can be used to
record information such as titles and
comments.
Composite video signal
A video signal in which luminance
and chrominance are combined along
with timing reference “sync”
information to make composite
video.
Sub clip
One of the sections which make up a
clip list. A sub clip may be part of a
clip or an entire clip.
MXF
Material eXchange Format. A file
exchange format developed by the
Pro-MPEG Forum. Equipment from
different manufacturers can
exchange files in this format.
Thumbnail image
A reduced still picture of video for
display on a GUI screen. XDCAM
creates thumbnail images from proxy
video, and displays them as index
pictures on GUI screens.
Drop-frame mode
SMPTE timecode runs at 30 frames/
second, while the NTSC color
television system runs at about 29.97
frames/second. Drop-frame mode
adjusts the running of timecode to
eliminate the discrepancy between
timecode value and actual time by
dropping two frames from the
timecode value at the beginning of
each minute except every tenth
minute.
Non-audio
General term for audio signals other
1)
than linear PCM, such as Dolby E
and Dolby Digital (AC-3).
1)
Timecode
A digitally encoded signal which is
recorded with video data to identify
each frame of the video by hour,
minute, second and frame number.
SMPTE timecode is applied to NTSC
system, and EBU timecode to PAL
and SECAM systems.
XDCAM can record non-audio as an
input signal.
1) Dolby is a trademark of Dolby Laboratories.
Non-drop-frame mode
A mode of advancing timecode
which ignores the difference in frame
values between real time and the
timecode. Using this mode produces
a difference of approximately 86
seconds per day between real time
and timecode, which causes
problems when editing programs in
units of seconds using the number of
frames as a reference.
E-E mode
UMID
Electric-to-Electric mode. When you
operate a VDR in E-E mode, input
video and/or audio signals pass
through electric circuits only and
then come out from the output
connectors, without passing through
electromagnetic conversion circuits
such as recording heads.
Unique Material Identifier. A
standard (SMPTE-330M) for video
and audio metadata. The Basic
section of a UMID contains a
globally unique number and a
material number for the identification
of recorded material. An optional
section called the “Source Pack”
contains information such as the time
and location of recording. A UMID
with the Basic section only is called a
Basic UMID. A UMID with the
Proxy AV data
Low-resolution data with a video
bandwidth of 1.5 Mbps and an audio
bandwidth of 64 kbps per channel.
This unit records proxy AV data
Essence mark
A type of metadata that may be set for
a specified frame.
Glossary
182
Source Pack is called an Extended
UMID.
User bits
A total of 32 bits are provided in the
timecode which the user can use to
record such information as date, reel
number, or scene number on video
tape or disc. Also called user’s bits.
VBID (Video Blanking ID)
This is a video ID signal, defined in
the EIAJ CPR-1204 standard, which
is inserted into VBS video output to
enable the aspect ratio to be detected.
The ID signal is inserted into line 20,
VBI 283.
183
Glossary
DISC MENU
Index
A
Accessories
ejecting with the unit powered off
Clip List
Analog
audio signal input/output section
ANALOG AUDIO
DISPLAY
Audio
Audio level
AUDIO MONITOR R, L connectors
COMPOSITE OUTPUT 1, 2 (SUPER)
E
Editing
Essence mark
Expand
B
returning to factory default
using the editing function of
Battery
C
D
CH-1/ALL CH, CH-2 to CH-4
Chapter
DIGITAL AUDIO (AES/EBU)
Digital audio signal input/output
F
File access mode (FAM) connections
184
Index
I
IN
File Operations in File Access Mode
(for Macintosh) 112
File Operations in File Access Mode
(for Windows) 110
Index picture
O
OUT
J
Jog
P
PDZ-1
recording continuous timecode
120
K
L
recording continuous timecode
120
M
Playback condition
Maintenance
Menu
Preparation
G
R
H
HDSDI remote control function
57
HDSDI OUTPUT 1, 2 (SUPER)
connectors 28
N
Network
Index
185
Recording and playback control
section 21
T
THUMBNAIL
Thumbnail
selecting information displayed
79
Returning to factory default settings
127
TIME CODE
S
Scene
SDSDI OUTPUT 1, 2 (SUPER)
connectors 29
Setup menu
recording external timecode
directly 45
recording sequentially upon the
44
recording with the internal
synchronized 44
Shuttle
U
User bits
SUB CLIP
V
W
186
Index
The material contained in this manual consists of information
that is the property of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use thereof for any purpose
other than the operation or maintenance of the equipment
described in this manual without the express written
permission of Sony Corporation.
PDW-F1600
PDW-HD1500
(SYL)
Sony Corporation
Printed in Japan
2009.05 13
© 2008
3-282-295-06 (1)
Printed on recycled paper.
|
Westcott 1863 User Manual
Weil McLain SGO Series 3 User Manual
Victor Enterprise 1260 3 User Manual
Venturer LCD Kitchen TV User Manual
Specialized S WORKS CARBON HARDTAIL User Manual
Sony Camcorder W570D User Manual
Sony BDP S590 3D Blu ray Disc Playe Blu Ray DVD Players BDPS590 User Manual
Sharp XE A403 User Manual
Sanyo NV E7000 User Manual
Sanyo CR V3 User Manual