Sony Camcorder HDC 950 User Manual

HD COLOR CAMERA

HDC-900

HDC-900/L

HDC-910

HDC-910/L

HDC-930

HDC-950

HD CCD BLOCK ADAPTOR

HKC-T950

INSTALLATION AND MAINTENANCE MANUAL

1st Edition (Revised 7)

For HDC-900/910/930/950

CAUTION

ADVARSEL

Danger of explosion if battery is incorrectly replaced.

Lithiumbatteri - Eksplosjonsfare.

Ved utskifting benyttes kun batteri som

anbefalt av apparatfabrikanten.

Brukt batteri returneres

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

apparatleverandøren.

Vorsicht!

VARNING

Explosionsgefahr bei unsachgemäßem Austausch

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ

som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande

föreskrifter.

der Batterie.

Ersatz nur durch denselben oder einen vom

Hersteller empfohlenen ähnlichen Typ. Entsorgung

gebrauchter Batterien nach Angaben des

Herstellers.

VAROITUS

ATTENTION

Paristo voi räjähtää jos se on virheellisesti

asennettu.

Il y a danger d’explosion s’il y a remplacement

incorrect de la batterie.

Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

Remplacer uniquement avec une batterie du même

type ou d’un type équivalent recommandé par le

constructeur.

Mettre au rebut les batteries usagées conformément

aux instructions du fabricant.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

HDC-900/950 IMM

1 (P)

For the customers in Japan

For the customers in the Netherlands

Voor de klanten in Nederland

Hoe u de batterijen moet verwijderen, leest u in de

Onderhoudshandleiding.

Gooi de batterij niet weg maar lever deze in als klein

chemisch afval (KCA).

Für Kunden in Deutschland

Entsorgungshinweis: Bitte werfen Sie nur entladene

Batterien in die Sammelboxen beim Handel oder den

Kommunen. Entladen sind Batterien in der Regel dann,

wenn das Gerät abschaltet und signalisiert “Batterie

leer” oder nach längerer Gebrauchsdauer der Batterien

“nicht mehr einwandfrei funktioniert”. Um

sicherzugehen, kleben Sie die Batteriepole z.B. mit

einem Klebestreifen ab oder geben Sie die Batterien

einzeln in einen Plastikbeutel.

For the customers in the U.S.A. and Canada

RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment

by returning your used rechargeable

batteries to the collection and recycling

location nearest you.

For more information regarding recycling of re-

chargeable batteries, call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion

batteries.

HDC-900/950 IMM

2 (P)

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 3 (E)

Related manuals................................................................................................... 3 (E)

Contents ............................................................................................................... 4 (E)

1. Installation Overview

1-1. Checking before Installation .................................................................1-1 (E)

1-1-1. Checking the ROM and Software Version...........................1-1 (E)

1-1-2. Setting the Format of HDCU (HDC-910/930) .....................1-1 (E)

1-2. Connectors and Cables ..........................................................................1-2 (E)

1-2-1. Connector Input/Output Signals...........................................1-2 (E)

1-2-2. Wiring Diagrams for Cables ..............................................1-13 (E)

1-2-3. Connection Connectors/Cables ..........................................1-14 (E)

1-2-4. Note in connecting CCU connector ...................................1-14 (E)

1-3. Location of Printed Circuit Boards .....................................................1-15 (E)

1-4. Opening/Closing the Side Panel..........................................................1-18 (E)

1-5. Switch Setting on the Boards ..............................................................1-19 (E)

1-6. Setting the Utility Out Voltage (HDC-900/910) .................................1-24 (E)

1-7. Adjusting the Position of the Shoulder Pad (HDC-950/930) ..............1-25 (E)

1-8. Installing the Incom Panel Assembly

to the Camera Backside (HDC-950/930) ............................................1-26 (E)

1-9. Installing the Battery Adaptor BKP-L551 (HDC-950/930) ................1-26 (E)

1-10. Disconnecting/Reconnecting Flexible Card Wire...............................1-27 (E)

1-11. Notes on Use of the RTS Kit...............................................................1-28 (E)

2. Service Overview

2-1. Cleaning of Connector/Cable ................................................................2-1 (E)

2-2. Cleaning the Vent Portion of the Fan (HDC-950/930 only) .................2-3 (E)

2-3. Replacing the Fuse ................................................................................2-4 (E)

2-3-1. HDC-900/910 .......................................................................2-4 (E)

2-3-2. HDC-950/930 .......................................................................2-4 (E)

2-4. Recommended Replacing Parts.............................................................2-5 (E)

2-4-1. HDC-900/910 .......................................................................2-5 (E)

2-4-2. HDC-950/930 .......................................................................2-6 (E)

2-4-3. HKC-T950............................................................................2-7 (E)

HDC-900/950 IMM

1 (E)

3. Setup Menu

3-1. Setup Menu ...........................................................................................3-1 (E)

3-2. TOP Menu .............................................................................................3-4 (E)

3-3. OPERATION Menu ..............................................................................3-5 (E)

3-4. PAINT Menu.........................................................................................3-7 (E)

3-5. MAINTENANCE Menu .....................................................................3-19 (E)

3-6. FILE Menu ..........................................................................................3-27 (E)

3-7. DIAGNOSIS Menu .............................................................................3-32 (E)

4. File System

4-1. File Structure .........................................................................................4-1 (E)

4-2. Operator File .........................................................................................4-2 (E)

4-3. Preset Operator File...............................................................................4-3 (E)

4-4. Registering the Scene File.....................................................................4-4 (E)

4-5. Registering Reference Files ..................................................................4-6 (E)

4-6. Registering the Lens File ......................................................................4-9 (E)

4-7. Registering the OHB File ....................................................................4-10 (E)

4-7-1. Storing the Black Shading and White Shading ..................4-10 (E)

4-7-2. Adjusting the ND Offset ....................................................4-11 (E)

4-8. File items .............................................................................................4-12 (E)

HDC-900/950 IMM

2 (E)

Manual Structure

Purpose of this manual

This manual is the installation and maintenance manual of HD Color Camera HDC-

900/910/950/930 and HD CCD Block Adaptor HKC-T950 for HDC-950/930.

This manual is intended for use by trained system and service engineers, and is

provided information required for the installation and maintenance information .

Related manuals

Besides this installation and maintenance manual, the following manuals are avail-

able.

. HDC-900/910 Operation Manual (Supplied with HDC-900/910)

This manual is necessary for the use and the operation of the HDC-900/910.

Part No. : 3-204-021-XX

. HDC-950/930 Operation Manual (Supplied with HDC-950/930)

This manual is necessary for the use and the operation of the HDC-950/930.

Part No. : 3-204-027-XX

. HKC-T950 Operation Manual (Supplied with HKC-T950)

This manual is necessary for the installation and operation of the HKC-T950.

Part No. : 3-206-420-XX

. Maintenance Manual (Available on request)

This manual is intended for use by trained system and service engineers, and

describes the information regarding the circuit description, replacement of main

parts, SERVICE menu and electrical alignment.

For obtaining, contact your local Sony Sales Office/Service Center.

Part No. : 9-968-560-XX

. e-manual (Tentative name) (Available on request)

This electronic manual intended for use by trained system and service engineers

describes (detailed parts list, block diagrams, schematic diagrams, and board

layouts.) required for parts-level service.

For obtaining, contact your local Sony Sales Office/Service Center.

. System Manual (Available on request)

This manual is necessary for connection and operation of this unit and other

peripheral equipment.

If this manual is required, please contact to your local Sony Sales Office/Service

Center.

HDC-900/950 IMM

3 (E)

. “Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in B&P Company equipment.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

maintenance manual for the corresponding unit. The maintenance manual contains

a complete list of all semiconductors and their ID Nos., and thus should be used

together with the CD-ROM.

Part number: 9-968-546-XX

Contents

The installation and maintenance manual is organized by following sections.

Section 1 Installation Overview

This section is described about the information that is required to install (switch

setting on the board, connection information, and the like.) and when installing this

unit.

Section 2 Service Overview

This section is described about the recommended replacing parts, replacing the fuse

and the cleaning procedures.

Section 3 Setup Menu

This section is described about the setup menu (TOP menu, OPERATION menu,

PAINT menu, MAINTENANCE menu, FILE menu and DIAGNOSIS menu).

Section 4 File System

This section is described about the file system to control data.

HDC-900/950 IMM

4 (E)

Section 1

Installation Overview

1-1. Checking before Installation

1-1-1. Checking the ROM and Software Version

When connecting the peripheral equipment in the list below to HDC-900/910/950/

930, be sure to check that the ROM and software version on each peripheral device

is corresponding to the camera to be connected.

When the HKC-T950 is used by connecting into the HDC-950/930, be sure to check

the version of ROM of HDC-950/930.

If the ROM and software version is lower than the specified below, be sure to

perform ROM replacement and updating the software.

If ROM replacement and updating the software are required, contact your local Sony

Sales Office/Service Center.

ROM

Peripheral equipment

Board name

Ref No.

Rom version

MSU-700A/750

CNU-700

CPU-293/CPU-286

AT-89 or AT-89A

AT-100

IC5, IC6/IC5, IC6

IC4, IC5

IC10

Ver. 1.10 or higher

Ver. 3.20 or higher

Ver. 2.80 or higher

Ver. 2.73 or higher

Ver. 1.00 or higher

Ver. 1.20 or higher

Ver. 1.21 or higher

Ver. 1.00 or higher

CNU-500

RCP-720/721

RCP-730/731

RCP-740/741

RCP-700/701

RM-B150

MPU-79

IC10

MPU-79

IC10

MPU-92

IC6

CPU-266

AT-130

IC4

HDC-950

IC1

HDC-930

AT-130

IC1

HDCU-900

HDCU-950

AT-141

IC105, IC106

IC206

AT-149

Software

Peripheral equipment

Board name

Software version

RCP-750/751

RM-B750

MPU-123

MPU-124

Ver. 1.01 or higher

Ver. 1.00 or higher

1-1-2. Setting the Format of HDCU (HDC-910/930)

When setting the format of HDCU-900/950 in the system using the HDC-910/930,

be sure to select the format corresponding to the HDC-910/930.

HDC-900/950 IMM

1-1 (E)

1-2. Connectors and Cables

1-2-1. Connector Input/Output Signals

HDC-900/910 Connector Layout

6 4 3 9 !, 7 8

!] != ![

HDC-900/950 IMM

1-2 (E)

1-2. Connectors and Cables

HDC-950/930 Connector Layout

^*4

!] 5

36 !\

* : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch.

PROMPTER OUT signal become effective when the camera is connected to CCU.

GENLOCK IN and RET IN signals become effective when the camera is used alone.

HKC-T950 Connector Layout

HDC-900/950 IMM

1-3 (E)

1-2. Connectors and Cables

Input/Output Signals

1 CCU connector

7 RET CONTROL (6P FEMALE)

Based upon BTA S-004A/005A/006A 1.485 Gbps

serial

Output Signals

2 EARPHONE OUT (HDC-950/930)

EARPHONE mini jack

(External view)

No. Signal

I/O

Specifications

3 TEST OUT

INCOM 1

MIC ON/OFF

Zi > 10 kZ

ON : GND

OFF : OPEN

BNC type 75 Z, 1.0 V p-p

INCOM 2

MIC ON/OFF

Zi > 10 kZ

ON : GND

OFF : OPEN

4 PROMPTER OUT^*

BNC type 75 Z, 1.0 V p-p

GND

——

5 HD SERIAL DIGITAL OUT

Based upon BTA-S004A

No connection

RET 1 ON/OFF

Zi > 10 kZ

ON : GND

OFF : OPEN

BNC type 75 Z, 0.8 V p-p 1.485 Gbps

@/ VIDEO OUT (HKC-T950)

RET 2 ON/OFF

Zi > 10 kZ

ON : GND

OFF : OPEN

BNC type 75 Z, 1.0 V p-p

Input Signals

4 GENLOCK IN^*(HDC-950/930)

8 DC OUT (4P FEMALE)

BNC type 75 Z, 1.0 V p-p

4 RET IN^*(HDC-950/930)

BNC type 75 Z, 1.0 V p-p

(External view)

6 Not used

No. Signal

I/O

Specifications

* : Use this connector by selecting PROMPTER OUT, GENLOCK IN and

RET IN signals with the switch on the rear panel of HDC-950/930.

PROMPTER OUT signal become effective when the camera is

connected to CCU.

GND

——

GND for POWER

No connection

GENLOCK IN and RET IN signals become effective when the camera is

used alone.

UNREG

OUT +12 V dc 500 mA (max)

HDC-900/950 IMM

1-4 (E)

1-2. Connectors and Cables

9 REMOTE (8P FEMALE)

INTERCOM CH1/CH2 (5P FEMALE)

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

TX (+)

HDC SERIAL DATA

INCOM MIC (Y)

INCOM MIC (X)

_20 dBu (CARBON MIC)

TX (_)

_60 dBu (DYNAMIC MIC)

RX (+)

HDCU/MSU/RCP/CNU/VCS

SERIAL DATA

GND (INCOM/PGM) ——

RX (_)

INCOM

RECEIVE

OUT 0 dBu

TX GND

——

GND for TX

PGM

OUT 0 dBu

POWER (+)

POWER GND

VIDEO (X)

CHASSIS GND

OUT +26 V, 200 mA (max)

(0 dBu = 0.775 Vrms)

——

GND for POWER (+)

75 Z, 1.0 V p-p

CHASSIS GND

!= AC OUT (HDC-900/910)

HDC-900/910 (CE) only

!/ AUDIO IN CH1/CH2 (3P FEMALE)

(External view)

No. Signal

I/O

Specifications

(External view)

GND

——

OUT

CHASSIS GND

UTL (C)

UTL (H)

AC 100 V, 200 V or below

No. Signal

I/O

Specifications

AUDIO (G)

——

_60 dBu, _50 dBu, _40 dBu,

AUDIO (X)

AUDIO (Y)

_30 dBu, _20 dBu, selectable

High impedance, Balanced

![ DC IN (4P MALE)

(0 dBu = 0.775 Vrms)

(External view)

No. Signal

I/O

Specifications

GND

——

GND for DC (+)

No connection

+10.5 to 17 V dc

DC (+)

HDC-900/950 IMM

1-5 (E)

1-2. Connectors and Cables

!] VTR (26P MALE) (HDC-900/910)

VTR (26P MALE) (HDC-950/930)

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

No connection

VTR UNREG

+10.5 to 17 V dc

VTR CMD GND

GENLOCK

——

GND for VTR CMD

UNREG GND

GENLOCK

——

GND for UNREG

Sync 0.6 V p-p, 0 V dc,

Zi = 75 Z

GENLOCK GND

G/Y GND

G/Y

——

OUT

GND for GENLOCK

GND for G/Y

GENLOCK GND

G/Y GND

G/Y

——

OUT

GND for GENLOCK

GND for G/Y

1 Vp-p, 0 V dc, Zo = 75 Z

1 V p-p, 0 Vdc, Zo = 75 Z

R/PR

1 Vp-p/±0.35 V p-p, 0 V dc,

Zo = 75 Z

R/PR

1 V p-p/±0.35 V p-p, 0 V dc,

Zo = 75 Z

R/PR GND

B/PB

——

GND for R/PR

R/PR GND

B/PB

——

GND for R/PR

OUT

1 Vp-p/±0.35 V p-p, 0 V dc,

Zo = 75 Z

OUT

1 V p-p/±0.35 V p-p, 0 V dc,

Zo = 75 Z

B/PB GND

——

OUT

GND for B/PB

B/PB GND

——

OUT

GND for B/PB

CH1 MIC (X)

_20 dBu, Low impedance,

Balanced

CH1 MIC (X)

_20 dBu, Low impedance

Balanced

10 CH1 MIC (Y)

11 CH1/CH2 MIC GND ——

GND for CH1/CH2 MIC

No connection

11 CH1/CH2 MIC GND ——

12 UNREG (+) SENSE IN

13 UNREG (_) SENSE IN

GND for CH1/CH2 MIC

12 NC

13 NC

No connection

14 INCOM LINE

15 CH2 MIC (X)

16 CH2 MIC (Y)

17 NC

IN/OUT 0.5 V p-p

14 INCOM LINE

15 CH2 MIC (X)

16 CH2 MIC (Y)

17 NC

IN/OUT 0.5 V p-p

OUT

_20 dBu, Low impedance,

Balanced

OUT

_20 dBu, Low impedance,

Balanced

No connection

18 RET VIDEO

1.0 V p-p, 0 V dc,

18 RET VIDEO

1.0 V p-p, 0 V dc,

Zi = 75 Z

19 RET VIDEO GND

20 AUDIO

——

GND for RET VIDEO

_6 dBu, 750 Z/1 kHz

RS-422

19 RET VIDEO GND ——

20 AUDIO IN

GND for RET VIDEO

_6 dBu, 750 Z/1 kHz

RS-422

21 RX COMMAND (X) IN

22 RX COMMAND (Y) IN

23 TX COMMAND (X) OUT

24 TX COMMAND (Y) OUT

21 RX COMMAND (X) IN

22 RX COMMAND (Y) IN

23 TX COMMAND (X) OUT

24 TX COMMAND (Y) OUT

RS-422

(0 dBu = 0.775 Vrms)

HDC-900/950 IMM

1-6 (E)

1-2. Connectors and Cables

!\ LENS (36P FEMALE) (HDC-900/910)

(External view)

No. Signal

I/O

Specifications

I/O

Specifications

No connection

23 RET 3 ON

Zi > 10 kZ

ON : GND

OFF : High impedance

COMMON 5 V

24 LENS ADRS 0

25 LENS ADRS 1

26 LENS ADRS 2

27 LENS ADRS 3

^*1

+12 V (LENS)

LENS DC GND

GND (SIG)

OUT +12 V (at 2 A)

——

GND for +12 V (LENS)

GND

No connection

28 EXTENDER 1

OUT ON : GND

OFF : High impedance

^*2

LENS EXT-1

LENS EXT-2

29 EXTENDER 2

OUT ON : GND

OFF : High impedance

10 LENS EXT-3

30 F DEM (FAR)

No connection

11 NC LENS AUX

OUT ON : GND

OFF : High impedance

31 INCOM 1

Zi > 10 kZ

ENG/PRD

ENG : GND

PRD : High impedance

12 IRIS POSI

Zi > 10 kZ

2 to 7 V

32 INCOM 2

Zi > 10 kZ

ENG : GND

PRD : High impedance

“3.4 ± 0.1 V (F16)”

“6.2 ± 0.1 V (F2.8)”

ENG/PROD

13 ZOOM POSI

14 RET 1 ON

Zi > 10 kZ

2 to 7 V

“2 V (WIDE), 7 V (TELE)”

33 INCOM MIC 1

Zi > 10 kZ

ON : GND

OFF : High impedance

Zi > 10 kZ

ON : GND

34 INCOM MIC 2

Zi > 10 kZ

ON : GND

OFF : High impedance

15 RET 2 ON

Zi > 10 kZ

ON : GND

OFF : High impedance

35 F CONT SIG

OUT No connection

IN No connection

36 F DEM (NEAR)

16 FOCUS POSI

17 IRIS CONT SIG

Zi > 10 kZ

2 to 7 V

“2 V (MIN), 7 V (∞ )”

^*1 Zi > 10 kZ

1 : High impedance

OUT 2 to 7 V

+0.5

0 : 0

“3.4 ±0.1 V (F16)”

“6.2 ±0.1 V (F2.8)”

LENS ADRS 0 (low-order bit)

LENS ADRS 3 (high-order bit )

Zo < 1 kZ

18 IRIS AUTO

OUT AUTO : GND

/MANU

MANU : High impedance

Zo < 1 kZ

^*2 Zi > 10 kZ

1 : High impedance

0 : 0 ±0.5 V

19 NC

No connection

20 NC

21 LENS R TALLY

OUT ON : GND

EX1

EX2

EX3

MODE

OFF : High impedance

Zo < 1 kZ

EXTENDER OFF

EXT-1 (x 1.5) ON

EXT-2 (x 2) ON

EXT-3 (x 2.5) ON

22 EXP POSITION

Zi > 10 kZ

1 to 4 V

1 V : _7.5d

4 V : +7.5d

HDC-900/950 IMM

1-7 (E)

1-2. Connectors and Cables

!\ LENS (12P FEMALE)

VF (25P FEMALE) (HDC-900/910)

(HDC-950/930, HKC-T950)

13 12 11 10

25 24 23 22 21 20 19 18 17 16 15 14

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

Y VIDEO (X)

VIDEO GND

P_RVIDEO (X)

OUT

——

OUT

——

OUT

1.0 V p-p, Zo = 75 Z

GND for P^RVIDEO

0.7 V p-p, Zo = 75 Z

GND for P^BVIDEO

0.7 V p-p, Zo = 75 Z

0 to 5 V dc

RET VIDEO

ENABLE : 0 V

DISABLE : +5 V or OPEN

ENABLE

VTR START

/STOP

ENABLE : 0 V

DISABLE : +5 V or OPEN

VIDEO GND

VIDEO (X)

GND

——

GND for UNREG

PEAKING

LEVEL

AUTO SERVO

OUT AUTO : +5 V

MANU : 0 V or OPEN

+12 V

OUT

+10.5 to +20 V

IRIS CONT

OUT +3.4 V (F16) to

+6.2 V (F2.8)

UNREG

OUT +10.5 V to +17 V

No connection

TTL level

IRIS POSITION

+3.4 V (F16) to

10 S-DATA

11 R TALLY

IN/OUT

OUT

+6.2 V (F2.8)

ON : +5 V

OFF : 0 V

AUTO/MANU

OUT AUTO IRIS : 0 V

MANUAL IRIS : +5 V

12 EFFECT

OUT

ON : +5 V

OFF : 0 V

EXTENDER

ON/OFF

EX 2 ON : GND

EX 0.8 ON : 30 kZ to GND

OFF : OPEN

13 NC

No connection

GND for Y VIDEO

TTL level

14 Y VIDEO GND

15 S-CK

——

OUT

EX 2 ON

EX 0.8 ON

16 BATT IND

ON : +5 V

OFF : 0 V

30 kΩ

17 CHASSIS GND

18 G TALLY

——

10 ZOOM

POSITION

WIDE : 2 V

TELE : 7 V

OUT

ON : +5 V

OFF : 0 V

11 FOCUS POSI

(/LENS RX)

∞ : 7 V

min. : 2 V

19 GND (+12 V)

20 GND (+12 V)

21 VF-SEL

——

GND for +12 V

12 (LENS TX)

OUT

BW : 0 V

COLOR : +5 V

22 H EXPAND

OUT

ON : GND

OFF : +5 V

23 NC

No connection

24 NC

25 V EXPAND

OUT

ON : GND

OFF : +5 V

HDC-900/950 IMM

1-8 (E)

1-2. Connectors and Cables

!; VF (20P FEMALE) (HDC-950/930)

EXT I/O (20P) (HDC-950/930)

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

S-DA TA

IN/OUT

TTL level

Y VIDEO (X)

OUT

——

OUT

——

OUT

——

OUT

——

IN/OUT

OUT

1.0 V p-p, Zo = 75 Z

GND for Y VIDEO

1.0 V p-p, Zo = 75 Z

GND for PROMPTER

±0.35 V p-p, Zo = 75 Z

GND for Pr VIDEO

±0.35 V p-p, Zo = 75 Z

GND for Pb VIDEO

TTL level

No connection

TTL level

Y VIDEO (G)

PROMPTER (X)

PROMPTER (G)

Pr VIDEO (X)

Pr VIDEO (G)

Pb VIDEO (X)

Pb VIDEO (G)

SDA VF

SCK

OUT

No connection

G TALLY

ON : 5 V

OFF : GND

No connection

10 VD

Negative Pulse,

10 NC

No connection

3.0 V p-p, Low impedance

11 NC

No connection

11 CALL ON

12 VF POWER OFF

ON : L (0 v)

OFF : H (+3 V)

12 Y VIDEO

13 VIDEO GND

14 Pb VIDEO

15 Pr VIDEO

16 NC

OUT

——

OUT

1.0 V p-p, Zo = 75 Z

GND for VIDEO

OUT

ON : H (+5 V)

OFF : L (0 V)

±0.35 V p-p, Zo = 75 Z

No connection

13 MAIN POWER

ON/OFF

ON : +8 V

OFF : GND

14 SCL VF

OUT

——

OUT

TTL level

15 TALLY GND

16 BACK TALLY

GND for TALLY

17 R TALLY

OUT

ON : 5 V

OFF : GND

ON : 5 V

OFF : GND

18 NC

No connection

17 PANEL DATA

18 PANEL DATA

19 VF UNREG +

20 GND

RX SERIAL DATA

TX SERIAL DATA

+12 V (+10.5 V to +17.0 V)

GND for UNREG

19 UNREG GND

20 UNREG

——

GND for UNREG

+10.5 V to +17 V

OUT

——

OUT

HDC-900/950 IMM

1-9 (E)

1-2. Connectors and Cables

!, TRACKER (FEMALE)

FRONT MIC (3P FEMALE) (HDC-950/930)

11 12 13 14 15

16 17 18 19

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

CHU MIC (G)

——

_60 dBu, _50 dBu, _40 dBu,

TRK R (X)

OUT TRACKER RECEIVE

0 dBu unbalanced

CHU MIC (X)

CHU MIC (Y)

_30 dBu, _20 dBu, selectable

High impedance, Balanced

TRK R (G)

——

GND for TRACKER R

(0 dBu = 0.755 Vrms)

GND

GND for UNREG/TALLY

(UNREG/TALLY)

R TALLY

OUT ON : 5 V (Open Collector)

OFF : 0 V (Open Collector)

@- MIC (HKC-T950)

(3P FEMALE)

(3P MALE)

TRK PGM (G)

UNREG

——

GND for PGM

OUT +12 V (+10.5 to +17.0 V)

TRK T (X)

TRK T (Y)

TRACKER TALK

0 dBu /_20 dBu

High impedance balanced

TRK T (G)

——

GND for TRACKER T

(External view)

No. Signal

(External view)

Specifications

10 TRK PGM (X)

11 NC

OUT _20 dBu unbalanced

I/O

No connection

12 G TALLY

OUT ON : 5 V (Open Collector)

OFF : 0 V (Open Collector)

AUDIO (G)

AUDIO (X)

AUDIO (Y)

——

_60 dBu, _50 dBu, _40 dBu,

_30 dBu, _20 dBu, selectable

13 NC

No connection

High impedance, Balanced

14 RX_DATA (0)

15 RX_DATA (1)

16 NC

TRUNK DATA IN, RS232-C

(0 dBu = 0.755 Vrms)

No connection

@= INCOM (HKC-T950)

17 NC

(5P FEMALE)

(5P MALE)

18 TX_DATA (0)

19 TX_DATA (1)

20 GND

OUT TRUNK DATA OUT, RS232-C

OUT

——

(0 dBu = 0.775 Vrms)

(External view)

No. Signal

(External view)

Specifications

I/O

INCOM MIC (Y)

INCOM MIC (X)

_20 dBu (CARBON MIC)

_60 dBu (DYNAMIC MIC)

GND (INCOMPGM) ——

INCOM RECEIVE OUT 0 dBu

PGM OUT 0 dBu

(0 dBu = 0.755 Vrms)

HDC-900/950 IMM

1-10 (E)

1-2. Connectors and Cables

@[ VF (HKC-T950)

(20P FEMALE)

11 10

11 12 13 14 15

16 17 18 19 20

17 16 15 14 13

20 19

(External view)

I/O Specifications

(External view)

No. Signal

I/O

Specifications

TTL level

S DATA

IN/OUT

TTL level

S DATA

IN/OUT

No connection

SCK

OUT

TTL level

SCK

TTL level

MANU : 0 V or OPEN

No connection

G TALLY

OUT

ON : 5 V

G TALLY

ON : 5 V

OFF : GND

No connection

1.0 V p-p, Zo = 75 Z

GND for VIDEO

No connection

1.0 V p-p, Zi = 75 Z

GND for VIDEO

No connection

10 NC

11 NC

12 Y VIDEO

13 VIDEO GND

14 NC

OUT

12 Y VIDEO

13 VIDEO GND

14 NC

——

15 NC

16 NC

17 R TALLY

OUT

ON : 5 V

17 R TALLY

ON : 5 V

OFF : GND

18 NC

No connection

18 NC

19 NC

20 NC

No connection

19 UNREG GND

20 UNREG

——

GND for UNREG

+10.5 V to +1.7 V

OUT

HDC-900/950 IMM

1-11 (E)

1-2. Connectors and Cables

@] CAM BODY (HKC-T950)

@\ OPT HEAD (HKC-T950)

(26P FEMALE)

(26P MALE)

(External view)

No. Signal

I/O

Specifications

No. Signal

I/O

Specifications

UNREG

13 V to 17 V

UNREG

OUT 13 V to 17 V

UNREG GND

OHB H

——

GND for UNREG

UNREG GND

OHB H

——

GND for UNREG

OUT 0.3 V p-p Positive pulse

0.3 V p-p Positive pulse

GND for OHB H

OHB H (G)

G VIDEO (G)

G VIDEO (X)

R VIDEO (X)

R VIDEO (G)

B VIDEO (X)

B VIDEO (G)

MIC (X)

——

GND for OHB H

OHB H (G)

G VIDEO (G)

G VIDEO (X)

R VIDEO (X)

R VIDEO (G)

B VIDEO (X)

B VIDEO (G)

MIC (X)

——

GND for G VIDEO

OUT 300 mV p-p, Zo = 75 Z (100 %)

300 mV p-p, Zi = 75 Z (100 %)

GND for R VIDEO

OUT 300 mV p-p, Zo = 75 Z (100 %)

——

OUT 95 mV p-p, Zo = 75 Z (100 %)

—— GND for B VIDEO

GND for R VIDEO

——

95 mV p-p, Zi = 75 Z (100 %)

GND for B VIDEO

——

OUT _60 dBu, _50 dBu, _40 dBu,

_60 dBu, _50 dBu, _40 dBu,

_30 dBu, _20 dBu, selectable

10 MIC (Y)

OUT _30 dBu, _20 dBu, selectable

10 MIC (Y)

11 INCOM/MIC GND ——

GND for INCOM/MIC,

CHU F, IRIS CONT

11 INCOM/MIC GND ——

GND for INCOM/MIC,

CHU F, IRIS CONT

12 IRIS CONT

13 CHU F

+3.4 V (F16) to +6.2 V (F2.8)

0.3 V p-p Positive pulse

0 dBu

12 IRIS CONT

13 CHU F

OUT +3.4 V (F16) to +6.2 V (F2.8)

OUT 0.3 V p-p Positive pulse

14 INCOM RECEIVE IN

14 INCOM RECEIVE OUT 0 dBu

15 INCOM MIC (X)

16 INCOM MIC (Y)

17 CHU H

OUT _20 dBu (CARBON MIC)

15 INCOM MIC (X)

16 INCOM MIC (Y)

17 CHU H

_20 dBu (CARBON MIC)

OUT _60 dBu (DYNAMIC MIC)

_60 dBu (DYNAMIC MIC)

150 mV p-p Positive pulse

180 mV p-p, Zi = 75 Z

GND for VF VIDEO,CHU H

0 dBu

OUT 150 mV p-p Positive pulse

18 VF VIDEO (X)

19 VF VIDEO (G)

20 PGM

18 VF VIDEO (X)

19 VF VIDEO (G)

20 PGM

OUT 180 mV p-p, Zo = 75 Z

——

GND for VF VIDEO, CHU H

OUT 0 dBu

21 RX COMMAND (X) IN

22 RX COMMAND (Y) IN

23 TX COMMAND (X) OUT

24 TX COMMAND (Y) OUT

21 RX COMMAND (X) OUT

22 RX COMMAND (Y) OUT 340 mV p-p

23 TX COMMAND (X) IN

340 mV p-p

24 TX COMMAND (Y) IN

HDC-900/950 IMM

1-12 (E)

1-2. Connectors and Cables

1-2-2. Wiring Diagrams for Cables

CCA-5 Cable

HDCZ Cable

Black

White

Yellow

Red

Black

Blue

Red

White

Red

Blue

Red

Brown

Gray

Red

White

Orange

White

Red

Yellow

White

HDC-900/950 IMM

1-13 (E)

1-2. Connectors and Cables

1-2-3. Connection Connectors/Cables

Indication

Connection connector/cable

REMOTE

(8P FEMALE)

1-766-848-11 Plug, 8P Male or

CCA-5 cable assembly (option)^*2

CCA-5-10 (10 m) /CCA-5-3 (3 m) or

REMOTE cable 1-783-372-11

Connection made with the connector panels during instal-

lation or service, should be made with the connectors/

complete cable assemblies specified in the following list,

or equivalent parts.

(supplied with RM-B150, 10 m) ^{*1 *2}

TRACKER

HIROSE HR25-9P-20P equivalent

(20P FEMALE)

Indication

Connection connector/cable

Cable assembly

(supplied with HKC-T950, 0.7 m)

1-792-603-21

TEST OUT

PROMPTER

SERIAL OUT

VIDEO OUT

(BNC)

1-569-370-12 Plug, BNC

(20P FEMALE)

*1: Use of REMOTE cable enables to monitor video signals.

*2: If using a cable of length different from a standard product, contact your

local Sony Sales Office/Service Center.

*3: Only for HKC-T950.

AUDIO IN

MIC IN

(3P FEMALE)

1-508-084-00 XLR, 3P Male or

ITT Cannon XLR-3-12C equivalent

Cable assembly

(supplied with HKC-T950, 0.8 m)

1-823-599-11^*3

1-2-4. Note in connecting CCU connector

MIC IN

(3P MALE)

1-508-083-00 XLR, 3P, Female or

ITT Cannon XLR-3-11C equivalent

Cable assembly

(supplied with HKC-T950, 0.8 m)

1-823-599-11^*3

It is recommendable to clean the optical contact portions

mentioned below before connecting this unit to the camera

control unit.

. CCU connector of this unit

. Camera connector of the camera control unit

. Optical/Electrical cable

RET CONTROL

(6P FEMALE)

1-560-078-00 Plug, 6P Male or

HIROSE HR10-7PA-6P equivalent

DC OUT

1-566-425-11 Plug, 4P Male or

(4P FEMALE)

HIROSE HR10A-7P-4P equivalent

It is also necessary to clean the optical contact portions

mentioned below before using the HDC-950/930 to the

large lens adaptor CA-905L.

INTERCOM

INCOM

(5P FEMALE)

1-508-370-11 XLR, 5P Male or

ITT Cannon XLR-5-12C equivalent

Cable assembly

(supplied with HKC-T950, 0.8 m)

1-823-600-11^*3

. CA cable of a large lens adaptor

. CCU connector of a large lens adaptor

INCOM

(5P MALE)

1-508-363-00 XLR, 5P Female or

ITT Cannon XLR-5-11C equivalent

Cable assembly

(supplied with HKC-T950, 0.8 m)

1-823-600-11^*3

For details on a cleaning method, refer to Section 2-1

“Cleaning of Connector/Cable”.

VTR

CAM BODY

1-564-184-00 Plug, 26P Female or

Cable assembly^*3

HDCZ-A10

(supplied with HKC-T950, 10 m)

1-823-615-11

HDCZ-A25 (option, 25 m)

1-823-616-11

HDCZ-A50 (option, 50 m)

1-823-617-11

OPT HEAD

(26P FEMALE)

1-564-183-31 Plug, 26P Male or

Cable assembly^*3

HDCZ-A10

(supplied with HKC-T950, 10 m)

1-823-615-11

HDCZ-A25 (option, 25 m)

1-823-616-11

HDCZ-A50 (option, 50 m)

1-823-617-11

DC IN

(4P MALE)

1-508-362-00 XLR, 4P Female or

ITT Cannon XLR-4-11C equivalent, or

Cable assembly 1-551-577-00

(Supplied with AC-550/550CE)

HDC-900/950 IMM

1-14 (E)

1-3. Location of Printed Circuit Boards

HDC-900/910

CN-986

RE-182

LE-172

AT-131

MB-883

RE-181

DU-104

AU-271

RE-184

AT-130

PS-582

SW-1020

SG-268

DAP-24

DAD-37

VDA-55

DPR-156

DPR-154

CN-2073

SW-1019

VA-196

SDI-49

IF-784

SW-1045

CN-2074

CN-1702

CN-1974

CN-2016

CN-1956

RX-28

CN-2015

CN-1998

CN-2017

BI-145

TG-214

BI-150

TG-214

DR-412

SERVO DRIVER

DR-492

SERVO DRIVER

RP-114

CN-1947

CN-2329

CN-1961

BI-145

BI-150

DU-69

NR-69/73

PA-239

NR-73

PA-239

HDC-900

HDC-910

HDC-900/950 IMM

1-15 (E)

1-3. Location of Printed Circuit Boards

HDC-950/930

RE-182

RE-184

CN-1952

DU-104

LP-113

RE-188

CN-1954

CN-1953

DPR-156

CN-2018

SW-1018

CN-1702B

CN-2094

RX-28

CN-1702B

SW-1017

SW-1027

CN-1951

CN-2063

SW-1016

MB-882

CN-1955

RE-181

AU-271

AT-130

SG-268

DAP-24

DAD-37

VDA-55

DPR-154

VA-196

CN-1964

SDI-49

SW-1014

SW-1015

CN-2026

SW-1029

SW-1013

PA-239

NR-69/73

PA-239

NR-69/73

TG-214

DU-69

BI-145

DU-69

BI-150

TG-214

RP-114

DR-412

SERVO DRIVER

RP-114

DR-492

SERVO DRIVER

CN-1961

CN-2329

CN-1947

BI-145

BI-150

HDC-950

HDC-930

HDC-900/950 IMM

1-16 (E)

1-3. Location of Printed Circuit Boards

HKC-T950

CN-2270 LE-256

AT-146

IF-845

CN-2271

SW-1065 SW-1066

RE-202

CN-2202

SW-1076

CN-2264

AT-147

CN-2203

IF-846

CN-2265

HDC-900/950 IMM

1-17 (E)

1-4. Opening/Closing the Side Panel

HDC-900/910

1. Unscrew the two lock screws of the side panel.

2. While sliding the safety lock toward the lens, open the

side panel by holding the handle.

3. Close the side panel and tighten securely the lock

screws of the side panel.

[Reference]

Closing the side panel brings the safety lock to an

automatic locking.

Safety lock

Handle

Lock screw of the

side panel

HDC-950/930

1. Unscrew the eight screws as shown in the figure, then

remove the inside panel and outside panel.

2. Reinstall in the reverse order of removal step 1.

Outside panel

Screws

Inside panel

HDC-900/950 IMM

1-18 (E)

1-5. Switch Setting on the Boards

AU-271 board

S101

S104

S102

INCOM 1 switch

S201

DYN

INCOM 1

MIC GAIN

S103

S202

INCOM 1 MIC GAIN switch

S301

S304

S204

INCOM 2 switch

DYN

INCOM 2

MIC GAIN

S203

INCOM 2 MIC GAIN switch

MIC MONITOR switch

MIC

MONITOR

S300

S303

OFF

AU-271 board (A side)

AU-271 board suffix -13 and higher

(B side)

Ref. No.

Name

Contents

Factory Setting

S1-1 ^*1

TRACKER INCOM2 ON/OFF Switch ON to mix the TRACKER TALK signal of the Tracker

connector to CCU INCOM2 RECEIVE OUT.

OFF

S1-2 ^*2

S2-1 ^*2

Not used

——

PGM1 INCOM1 RECEIVE

MIX ON/OFF

Switch ON to mix the PGM1 signal adjusted the sound volume by

the PGM volume control to the INCOM1 RECEIVE signal before

the sound volume adjustment.

OFF

S2-2

PGM2 INCOM2 RECEIVE

MIX ON/OFF

Switch ON to mix the PGM2 signal adjusted the sound volume

by the PGM volume control to the INCOM2 RECEIVE signal before

the sound volume adjustment.

OFF

S101-1

S101-2

S101-3

S101-4

S102-1

S102-2

S102-3

S102-4

PGM1 MUTE ON/OFF

PGM2 MUTE ON/OFF

INCOM1 MUTE ON/OFF

INCOM2 MUTE ON/OFF

PGM1 MUTE ON/OFF

PGM2 MUTE ON/OFF

INCOM1 MUTE ON/OFF

INCOM2 MUTE ON/OFF

Switch OFF to output the PGM1 signal to the PGM OUT of the

INTERCOM1 connector.

OFF

Switch OFF to output the PGM2 signal to the PGM OUT of the

INTERCOM1 connector.

Switch OFF to output the INCOM1 RECEIVE signal to the PGM OUT OFF

of the INTERCOM1 connector.

Switch OFF to output the INCOM2 RECEIVE signal to the PGM OUT ON

of the INTERCOM1 connector.

Switch OFF to output the PGM1 signal to the INCOM OUT of

the INTERCOM1 connector.

OFF

Switch OFF to output the PGM2 signal to the INCOM OUT of

the INTERCOM1 connector.

Switch OFF to output the INCOM1 RECEIVE signal to the INCOM

OUT of the INTERCOM1 connector.

OFF

Switch OFF to output the INCOM2 RECEIVE signal to the INCOM

OUT of the INTERCOM1 connector.

HDC-900/950 IMM

1-19 (E)

1-5. Switch Setting on the Boards

Ref. No.

Name

Contents

Factory Setting

S103

INCOM1 MIC GAIN +/0/_

Select the audio level of INTERCOM1/2 to be sent to CCU.

+ :+6dB

0 : 0dB

_ :_6dB

S104

INCOM1 MIC TYPE

Select from two options below in accordance with the microphone

of the head set connected to the INTERCOM1/2 connector.

CM : Carbon microphone

DYN :Dynamic microphone

S201-1

S201-2

S201-3

S201-4

S202-1

S202-2

S202-3

S202-4

S203

PGM1 MUTE ON/OFF

PGM2 MUTE ON/OFF

INCOM1 MUTE ON/OFF

INCOM2 MUTE ON/OFF

PGM1 MUTE ON/OFF

PGM2 MUTE ON/OFF

INCOM1 MUTE ON/OFF

INCOM2 MUTE ON/OFF

INCOM2 MIC GAIN +/0/_

Switch OFF to output the PGM1 signal to the PGM OUT of the

INTERCOM2 connector.

OFF

Switch OFF to output the PGM2 signal to the PGM OUT of

the INTERCOM2 connector.

Switch OFF to output the INCOM1 RECEIVE signal to the PGM

OUT of the INTERCOM2 connector.

Switch OFF to output the INCOM2 RECEIVE signal to the PGM

OUT of the INTERCOM2 connector.

Switch OFF to output the PGM1 signal to the INCOM OUT of the

INTERCOM2 connector.

Switch OFF to output the PGM2 signal to the INCOM OUT of the

INTERCOM2 connector.

Switch OFF to output the INCOM1 RECEIVE signal to the INCOM

OUT of the INTERCOM2 connector.

Switch OFF to output the INCOM2 RECEIVE signal to the INCOM

OUT of the INTERCOM2 connector.

Select the audio level of the INTERCOM1/2 to be sent to CCU.

+ :+6dB

0 : 0dB

_ :_6dB

S204

INCOM2 MIC TYPE

Select from two options below in accordance with the microphone of

the head set connected to the INTERCOM 1/2 connector.

CM : Carbon microphone

DYN :Dynamic microphone

S300-1^*3

S300-2^*3

S301-1

S301-2

S301-3^*1

S301-4^*1

S303

AUDIO1 +12 V OFF/ON

Switch ON to supply +12 V for MIC POWER to the microphone

connected the AUDIO IN 1 connector.

OFF

AUDIO2 +12 V OFF/ON

Switch ON to supply +12 V for MIC POWER to the microphone

connected the AUDIO IN 2 connector.

TRACKER RECEIVE OUT

PGM1 MIX

Switch ON to mix the PGM1 signal to the TRACKER RECEIVE OUT

of the TRACKER connector.

TRACKER RECEIVE OUT

PGM2 MIX

Switch ON to mix the PGM2 signal to the TRACKER RECEIVE OUT

of the TRACKER connector.

TRACKER RECEIVE OUT

IMCOM2 RECEIVE MIX

Switch ON to mix the INCOM2 RECEIVED signal to the TRACKER

RECEIVE OUT of the TRACKER connector.

TRACKER RECEIVE OUT

INCOM2 TALK MIX

Switch ON to mix the INCOM2 TALK signal to the TRACKER

RECIVE OUT of the TRACKER connector.

MIC MONITOR ON/OFF

Switch ON to monitor the microphone input signal at the INCOM OUT OFF

or EARPHONE OUT.

S304

TRACKER (T) 0/_20

Select the input level of the TRACKER Connector.

0 : 0dBu

_20 : _20dBu

(0dBu = 0.775 Vrms)

HDC-900/950 IMM

1-20 (E)

1-5. Switch Setting on the Boards

*1: The Tracker connector communicates to INCOM1 at the standard setting, yet it is communicable to INCOM2 by setting S1-1, S301-1

and S301-4

to ON.

*2: When setting S2-1 or S2-2 to ON, set bit1 and bit2 of S101, S102, S201 and S202 as shown below to prevent PGM1 and PGM2

signals from being mixed double.

S2-1

S101, 102, 201, 202

bit1

S2-2

S101, 102, 201, 202

bit12

INCOM1

PGM1/2 swiitch

(Panel)

S101

PGM 1

bit1

bit2

bit3

bit4

PGM OUT

INTERECOM CH1

INTERECOM CH2

INCOM2

PGM1/2 swiitch

(Panel)

S102

bit1

bit2

INCOM OUT

bit3

PGM 2

bit4

CCU

S201

S2-1

bit1

bit2

bit3

bit4

PGM OUT

INCOM1

S2-2

S202

bit1

bit2

bit3

bit4

INCOM OUT

INCOM2

Each bit of S101, S102, S103 and S104 is opened when it is set to “ON” position.

Set to “OFF”position to close the switch.

*3: AU-271 board suffix -13 and higher.

HDC-900/950 IMM

1-21 (E)

1-5. Switch Setting on the Boards

DU-104 board

DU-104 board (A side)

[Reference]

The switch setting on this board is valid only when connecting the RTS kit (optional) to the INTERCOM2 connector.

Ref. No.

Name

Contents

Factory Setting

RTS1 RTS 1/NORM/POW

Selects the function of the RTS CH1 side.

NORM

RTS 1 : RTS CH1 of the RTS kit operates as INCOM1 signal line.

NORM : Select NORM except when connecting to the RTS kit.

POW : RTS CH1 of the RTS kit operates as the power supply line

for the RTS belt pack.

RTS2 RTS 2/NORM/POW

Selects the function of the RTS CH2 side.

NORM

RTS 2 : RTS CH2 of the RTS kit operates as INCOM2 signal line.

NORM : Select NORM except when connecting to the RTS kit.

POW : RTS CH2 of the RTS kit operates as the power supply line

for the RTS belt pack.

S4-1

S4-2

RTS1 ON/OFF

RTS2 ON/OFF

Switch ON to use the RTS CH1 as the INCOM1 signal line.

Switch ON to use the RTS CH2 as the INCOM2 signal line.

OFF

When not connecting the RTS kit, make the settings same as factory settings.

When S4-1 setting is ON, set S1 to RTS1, S201-1 through S201-4 on the AU-271 board to ON.

When S4-2 setting is ON, set S2 to RTS2, S201- through S201-4 on the AU-271 board to ON.

HDC-900/950 IMM

1-22 (E)

1-5. Switch Setting on the Boards

AT-130 board

S100

AT-130 board (B side)

Never change the setting of the factory use switches.

The state of the factory setting is different with models.

Switch No.

Designation

Description

Factory setting

S100 1 to 4

SETUP MENU

Select

Setup menu to be displayed on the

viewfinder can be selected. (See the table below)

OFF

S100 5 to 8

——

Factory use

—

Switch Settings

Setup Menu

S100-1 S100-2 S100-3 S100-4

USER^*USER MENU^*OPERATION PAINT MAINTENANCE FILE DIAGNOSIS

CUSTOMIZE

OFF

Yes

OFF

* : These menus are displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

HDC-900/950 IMM

1-23 (E)

1-6. Setting the Utility Out Voltage (HDC-900/910)

1-6. Setting the Utility Out Voltage

(HDC-900/910)

HDC-900/910 (CE) only

Set the utility out voltage in accordance with the voltage of

peripheral devices when they are connected to the camera.

The setting of the utility out voltage can be made by the

combination of the switches 1 and 2 in the figure.

PRESET

AC100V

VTR

AC OUT

DC IN

PRESET

AC100V

200VA MAX

Voltage indication seal

PRESET AC100V

PRESET AC230V~

AC240V~

PRESET

AC120V

PRESET

100 120

230

PRESET AC220V~

. When setting to 100 V

When changing the voltage setting, change the voltage

indication seal.

100 120

230

The seal is supplied with this unit.

. When setting to 120 V

100 120

230

. When setting to 230 V

Operation of the switch 1 is not required.

100 120

230

HDC-900/950 IMM

1-24 (E)

1-7. Adjusting the Position of the Shoulder Pad (HDC-950/930)

1-7. Adjusting the Position of the

Shoulder Pad (HDC-950/930)

The shoulder pad is factory-configured to the more for-

ward position considering the mass of the camera, yet it is

adjustable according to the type of the lens by following

the procedures below.

1. Remove the three screws shown in the figure and take

the shoulder pad out.

2. Remove the two screws to remove the pad spacer.

3. Slide the shoulder pad backward 10 mm and fix it with

the three screws.

Pad spacer

Screws (B3 x 8)

Screws (B3 x 6)

Screw (B4 x 20)

Shoulder pat assembly

HDC-900/950 IMM

1-25 (E)

1-8. Installing the Incom Panel Assembly to the Camera Backside (HDC-950/930)

1-9. Installing the Battery Adaptor BKP-L551 (HDC-950/930)

1-8. Installing the Incom Panel

Assembly to the Camera Backside

(HDC-950/930)

1-9. Installing the Battery Adaptor

BKP-L551 (HDC-950/930)

This section describes the method of installing the battery

adaptor to the right from the standard position.

When disconnecting/connecting a flexible card wire, refer

to Section 1-10.

1. Unscrew the four screws of the blank panel to remove

the blank panel.

1. Unscrew the four screws to the blank panel to remove

the blank panel.

2. Reattach the blank panel upside down with the four

screws.

3. Install the battery adaptor referring to BKP-L551

installation manual.

Screws

Use care that attaching the battery adaptor in this way

restricts the operation of the CCU connector.

Screws

Blank panel

CN1

Screws

Incom panel assembly

Flexible card wire

Screws

2. Unscrew the four screws to the incom panel assembly

and disconnect the flexible card wire from the connec-

tor CN1 of the SW-1017 board, then remove the incom

panel assembly.

Screws

Blank panel

3. Pull out the flexible card wire of the backside of the

camera and connect the connector CN1 of the SW-

1017 board.

4. Exchange the position of the incom panel assembly

and blank panel and install both of them with the

screws.

Flexible card wire

Screws

CN1

Screws

Incom panel assembly

Screws

Blank panel

HDC-900/950 IMM

1-26 (E)

1-10. Disconnecting/Reconnecting Flexible Card Wire

. Be sure to turn off the power when disconnecting and connecting the flexible card wire. To power off,

be sure to disconnect the cable connected to the DC IN connector or the battery, in addition to turning

off the power switch.

. The holded flexible card wire remarkably shortens the life span. Pay careful attention when handling it.

Disconnecting

. Do not pull the flexible card wire before unlocking.

. There are a conductive portion (printed side) and insulation portion (white belt) in the flexible card

wire. Confirm the direction of the flexible card wire before connecting it.

1. Unlock by shifting portion A of the connector in the direction indicated by the arrow, then pull out

the flexible card wire.

Flexible card wire

Insulation portion

Connector

Reconnecting

. Ensure that no stain or dust adheres on the conductive surface of the flexible card wire.

. Ensure that the connector is unlocked.

1. Insert the flexible card wire firmly as far as it will go.

2. Press in the portion A of the connector in the direction indicated by the arrow to lock the connector.

At that time, take care that the flexible card wire is not inclined.

Flexible card wire

Connector

HDC-900/950 IMM

1-27 (E)

1-11. Notes on Use of the RTS Kit

Connecting the RTS Intercom System Kit BKP-7913

(option) to the INTERCOM 2 connector of HDC-900/910/

950/930 allows the INTERCOM 2 connector to work with

an RTS intercom system, and be connected to up to two

child devices.

When connecting the RTS kit, perform the following

setting.

AU-271 board suffix -12

Set the switches on the DU-104 board referring to Section

1-5.

AU-271 board suffix -13 and higher

Mount the following chip conductor to R271 (B side : A-1)

on the AU-271 board, and Set the switches on the DU-104

board referring to Section 1-5.

Ref.No. Name

SONY Part No.

R271

CONDUCTOR, CHIP (1608)

1-216-864-11

R271

AU-271 board suffix -13 and higher

(B side)

HDC-900/950 IMM

1-28 (E)

Section 2

Service Overview

2-1. Cleaning of Connector/Cable

Cleaning

It is recommendable to clean the optical contact portions

mentioned below before connecting this unit to the camera

control unit.

Male connector

Clean the tip of the white optical contacts by a cotton swab

moistened with alcohol.

. CCU connector of this unit

. Camera connector of the camera control unit

. Optical/Electrical cable

Optical contacts (white)

It is also necessary to clean the optical contact portions

mentioned below before using the HDC-950/930 to the

large lens adaptor CA-905L.

. CA cable of a large lens adaptor

. CCU connector of a large lens adaptor

Follow the procedures below for cleaning.

Female connector

The optical contacts for female connector are in an unex-

posed state. In cleaning, it is necessary to be exposed by

removing the alignment sleeve in advance. Proceed as

follows.

Tools Required

. Alignment sleeve remover HC-001

(for female connector)

Sony P/N:

J-6480-010-A

1. Insert the alignment sleeve remover into the alignment

sleeve in the straight line and turn it clockwise.

Insert the shorter nose end when removing/installing the

alignment sleeve.

Grasp not the shock absorber portion of the remover but

the handle in use.

Shock absorber portion

Handle

Insert the shorter nose end

. Cotton swabs (commercially available)

Use the cotton swab with its diameter of around 4 mm.

The cotton swab with its diameter more than 5 mm does

not enough reach to the inner part of the cable, so that

cannot clean the tip of the optical contact.

HDC-900/950 IMM

2-1 (E)

2-1. Cleaning of Optical Connector

2. When the turn stops, pull out the remover in the

straight line forcedly.

The alignment sleeve can be removed/reinstalled with

the sleeve itself attached to the tip of the remover.

Great care should be taken so as not to lose or damage

the alignment sleeve.

(Alignment sleeve: Sony P/N 9-980-074-01)

Alignment sleeve

3. Clean the tip of the white optical contacts by a cotton

swab moistened with alcohol.

Optical contacts (white)

4. Insert the remover with the alignment sleeve attached

to its tip, and push it until it clicks.

5. Rotate the remover counterclockwise to install the

alignment sleeve, and extract the remover.

HDC-900/950 IMM

2-2 (E)

2-2. Cleaning the Vent Portion of the Fan (HDC-950/930 only)

2-2. Cleaning the Vent Portion of the

Fan (HDC-950/930 only)

Tail Net

1. Remove the two screws to remove the tail guard.

2. Take out the tail net and remove dust on the tail net

with a vacuum cleaner.

A part for preventing from dust is attached in the vent

portion of the fan. Clean this component every two or three

months. Clogging may cause the temperature increases

inside the camera and result in a trouble.

. Top Chassis Cover Assembly

. Fan Grill

. Tail Net

Top Chassis Cover Assembly

(A top cushion is stuck on the backside of the assembly for

protecting from dust.)

B3 x 6

Tail net

1. Remove the four screws (precision P2.6 x 5) to

remove the tope chassis assembly.

Tail guard

B3 x 6

2. Wash manually the top chassis cover assembly with

neutral detergent and dry in the shade.

Fan Grill

1. Remove the top chassis cover assembly.

2. Remove the four screws (precision P2.6 x 5) to take

out the fan grill holder.

3. Take out the fan grill and remove dust on the fan grills

with a vacuum cleaner.

Top chassis cover assembly

Precision

P2.6 x 5

Precision

P2.6 x 5

Precision

P2.6 x 5

Fan grill holder

Fan grill

HDC-900/950 IMM

2-3 (E)

2-3. Replacing the Fuse

2-3-2. HDC-950/930

Fuses for protecting from the overcurrent are mounted in

the HDC-950/930.

When a fuse burns, find out the cause of the overcurrent

and solve it before replacing the fuse.

The fuse is critical for safely operating. Do exchange with

the fuses authorized by the manufacturer, otherwise a fire

and electric shock may occur.

2-3-1. HDC-900/910

When replacing, be sure to use the specified fuse below.

Description

Part No.

In the power supply portion of the HDC-900/910, fuses for

protecting from the overcurrent are mounted on each

circuit and each block.

FUSE GLASS 10 A/125 V

! 1-576-048-11

Replacing

When a fuse burns, find out the cause of the overcurrent

and solve it before replacing the fuse.

1. Remove the fuse holder with a flat blade screwdriver

and replace the fuse.

When replacing, be sure to use the specified fuses below.

Holder’s name Description

Part No.

MAIN

FUSE (H.B.C.) 4 A/250 V

! 1-576-231-11

LENS

! 1-576-231-11

FUSE (H.B.C.) 6.3 A/250 V ! 1-576-233-11

CAMERA

OTHERS

FUSE (H.B.C.) 4 A/250 V

FUSE (H.B.C.) 2 A/250 V

! 1-576-231-11

! 1-576-228-11

Fuse

Replacing

Fuse holder

1. Open the side plate. (Refer to Section 1-4.)

2. Remove the fuse holder with a flat blade screwdriver

and replace the fuse.

Use care that the fuses to be used differ depending on

the fuse mounting position.

CAMERA

OTHERS

LENS

MAIN

Fuse

Fuse holder

HDC-900/950 IMM

2-4 (E)

2-4. Recommended Replacing Parts

2-4-1. HDC-900/910

No. Description

Sony Part No.

Following parts are recommended replacing parts. The

optical filter unit may become cloudy with the lapse of

time. By such a cloudy optical filter unit, the characteris-

tics of this camera could not fully exploited, therefore

replace it if necessary.

Besides, the parts made of rubber used for this camera may

become cracked and split with the lapse of time, therefore

also replace it if necessary.

KNOB (DIA 3) ASSY, VOLUME

KNOB, VOLUME (DIA 6)

X-3167-563-X

3-185-872-0X

3-602-483-0X

3-615-750-6X

3-612-712-0X

3-627-260-0X

KNOB, VOLUME 6

SHIELD CUSHION (C)

BAND, CLAMP

PACKING, FAN

FILTER UNIT, OPTICAL

1-758-483-11

(HDC-900)

1-758-778-11

(HDC-910)

HDC-900/950 IMM

2-5 (E)

2-4. Recommended Replacing Parts

2-4-2. HDC-950/930

No. Description

Sony Part No.

Following parts are recommended replacing parts. The

optical filter unit may become cloudy with the lapse of

time. By such a cloudy optical filter unit, the characteris-

tics of this camera could not fully exploited, therefore

replace it if necessary.

Besides, the parts made of rubber used for this camera may

become cracked and split with the lapse of time, therefore

also replace it if necessary.

CAP, CONNECTOR (CCZ)

3-612-791-0X

3-626-974-0X

3-627-210-0X

3-627-968-0X

A-8279-359-X

3-679-668-0X

CAP, TRK

CUSHION, FAN

BUSHING, RUBBER

PAD ASSY, SHOULDER

BUTTON, VTR START

FILTER UNIT, OPTICAL

1-758-483-11

(HDC-950)

1-758-778-11

(HDC-930)

No. Description

Sony Part No.

3-676-244-0X

3-626-953-0X

COVER, SWITCH

SHEET, HANDLE

PACKING, VF

COVER, SW

3-710-024-0X

3-676-244-1X

RUBBER (EA), DROP PROTECTION 3-724-730-0X

CHASSIS COVER ASSY, TOP

X-3605-899-X

HDC-900/950 IMM

2-6 (E)

2-4. Recommended Replacing Parts

2-4-3. HKC-T950

Following parts are recommended replacing parts.

Besides, the parts made of rubber used for this adaptor may

become cracked and split with the lapse of time, therefore

also replace it if necessary.

Description

Sony Part No.

COVER, SWITCH

SHEET, HANDLE

PACKING, VF

3-676-244-0X

3-626-953-0X

3-710-024-0X

3-627-210-0X

CUSHION, FAN

HDC-900/950 IMM

2-7 (E)

Section 3

Setup Menu

3-1. Setup Menu

The setup menu is used for selecting various setting values, items displayed on the viewfinder screen, the

method of displaying, and adjustments. The menu is displayed on the viewfinder screen. The menu can

also be displayed by connecting an external monitor to the TEST OUT connector.

Structure of Setup Menu

The setup menu is composed of the following menus.

. USER menu (This menu is displayed only when the ROM version on the AT board of the unit is Ver

1.30 or higher.)

. USER MENU CUSTOMIZE menu (This menu is displayed only when the ROM version on the AT

board of the unit is Ver 1.30 or higher.)

. OPERATION menu

. PAINT menu

. MAINTENANCE menu

. FILE menu

. DIAGNOSIS menu

[Reference]

Beside above menus, the TOP menu is provided for indicating the whole configuration of the menu items.

Selecting the Menu

The menus to be displayed on the viewfinder screen can be selected by the switches on the AT-130 board

(S100-1 to S100-4). This unit is set to display all menu at the factory setting.

(

) : Shows the factory setting

Switch Settings

Setup Menu

S100-1 S100-2 S100-3 S100-4

USER

USER MENU OPERATION

PAINT

MAINTENANCE

FILE

DIAGNOSIS

CUSTOMIZE

(OFF)

OFF

(OFF)

OFF

(OFF)

OFF

Yes

OFF

Equipment Required

HDC-900/910

7-type viewfinder HDVF-700A/7700/C700W (or black-and-white monitor)

Camera control unit HDCU-900/700A

HDC-950/930

2-type viewfinder HDVF-20A (or black-and-white monitor)

Camera control unit HDCU-900/950/700A, or AC adapter AC-550, etc. for supplying the power to the

camera.

HDC-900/950 IMM

3-1 (E)

3-1. Setup Menu

Switches (HDC-900/910)

DISPLAY switch

: Displays characters and messages indicating the

settings and operating status of the unit on the

viewfinder screen.

OFF : Turns off all the displays on the viewfinder

screen.

MENU : Displays the setup menu on the viewfinder screen.

MENU SELECT control

Selects the items displayed on the viewfinder screen and

changes settings.

MENU SELECT switch

ENTER : Determines the menu and item selected by the

MENU SELECT control, and determines the

setting values.

CANCEL : Cancels the menu setting mode and returns to

the page selection mode or TOP menu.

MENU SELECT control

MENU SELECT switch

DISPLAY switch

Basic Operations (HDC-900/910)

1. Displaying the menu

To display the OPERATION menu, turn the power on and set the DISPLAY switch to “MENU”. ^(*1)

To display the other menus, set the DISPLAY switch from “OFF” to “MENU” while pressing the

MENU SELECT switch toward the “ENTER” side, and obtain the TOP menu screen. Turning the

MENU SELECT control, select the menu to be displayed, and press the MENU SELECT switch

toward the “ENTER” side.

2. To change pages, set the cursor to the page number and turn the MENU SELECT control.

3. To shift the cursor, turn the MENU SELECT control. (Pressing the MENU SELECT switch toward

the “ENTER” side determins the setting.)

4. To change a setting value, set the cursor to the item to be changed and press the MENU SELECT

switch toward the “ENTER” side, then the cursor turns to “?” and the value changes by turning the

MENU SELECT control.

(Turning it fast, the value changes greatly, while turning it slowly, the value changes slightly for fine

adjustment.) To determine the setting, press the MENU SELECT switch toward the “ENTER” side,

and to cancel the change, press the MENU SELECT switch toward the “CANCEL” side.

5. By every set of the MENU SELECT switch to “CANCEL”, the screen returns to the item selection

mode, page selection mode, and then TOP menu^(*2)

6. To delete the menu displayed, set the DISPLAY switch to “OFF”.

(*1) : The display screen at the power on is changeable. For change, refer to MENU RESUME item in

OTHERS 2 Page of the MAINTENANCE menu.

(*2) : The page selection mode is available, only when the basic operation step1 was performed and the

operation started from the TOP menu.

Displaying characters on an external monitor (HDC-900/910)

When you want to display characters including the menu on an external monitor connected to the TEST

OUT conector, proceed as follows.

1. Displaying characters. (including the menu)

While pressing the MENU switch toward the “CANCEL” side, set the DISPLAY switch from “OFF”

to “MENU”.

2. To remove the characters/menu from the external monitor.

While pressing the MENU switch towards the “CANCEL” side, set the DISPLAY switch from

“MENU” to “OFF”.

HDC-900/950 IMM

3-2 (E)

3-1. Setup Menu

Switches (HDC-950/930)

DISPLAY switch

: Displays characters and messages indicating the

settings and operating status of the unit on the

viewfinder screen.

OFF : Turns off all the displays on the viewfinder

screen.

MENU : Displays the setup menu on the viewfinder screen.

Rotary Encoder

Selects the items displayed on the viewfinder screen and

changes settings.

MENU switch

STATUS : Allows you to check the current setting.

CANCEL : Cancels the menu setting mode and returns to

the page selection mode or TOP menu.

DISPLAY switch

MENU switch

Rotary Encoder

Basic Operations (HDC-950/930)

1. Displaying the menu

To display the OPERATION menu, turn the power on and set the DISPLAY switch to “MENU”. ^(*1)

To display the other menus, set the DISPLAY switch from “OFF” to “MENU” while pressing the

rotary encoder, and obtain the TOP menu screen. Turning the rotary encoder, select the menu to be

displayed, and press the rotary encoder.

2. To change pages, set the cursor to the page number and turn the Rotary encoder.

3. To shift the cursor, turn the Rotary encoder. (Pressing the Rotary encoder determins the setting.)

4. To change a setting value, set the cursor to the item to be changed and press the Rotary encoder, then

the cursor turns to “?” and the value changes by turning the Rotary encoder.

(Turning it fast, the value changes greatly, while turning it slowly, the value changes slightly for fine

adjustment.) To determine the setting, press the Rotary encoder, and to cancel the change, press the

MENU switch toward the “CANCEL” side.

5. By every set of the MENU switch to “CANCEL”, the screen returns to the item selection mode, page

selection mode, and then TOP menu^(*2)

6. To delete the menu displayed, set the DISPLAY switch to “OFF”.

(*1) : The display screen at the power on is changeable. For change, refer to MENU RESUME item in

OTHERS 2 Page of the MAINTENANCE menu.

(*2) : The page selection mode is available, only when the basic operation step1 was performed and the

operation started from the TOP menu.

Displaying characters on an external monitor (HDC-950/930)

When you want to display characters including the menu on an external monitor connected to the TEST

OUT conector, proceed as follows.

1. Displaying characters. (including the menu)

While pressing the MENU switch toward the “CANCEL” side, set the DISPLAY switch from “OFF”

to “MENU”.

2. To remove the characters/menu from the external monitor.

While pressing the MENU switch towards the “CANCEL” side, set the DISPLAY switch from

“MENU” to “OFF”.

HDC-900/950 IMM

3-3 (E)

3-2. TOP Menu

The TOP menu is provided for indicating the whole configuration of the menu items.

Displaying the TOP menu

HDC-900/910 : Set the DISPLAY switch from “OFF” to “MENU” while pressing the MENU SELECT

switch toward the “ENTER” side.

HDC-950/930 : Set the DISPLAY switch from “OFF” to “MENU” while pressing the rotary encoder.

[Reference]

To select the menu to be displayed on the viewfinder, switch setting on the AT-130 board is required.

For details, refer to “Selecting the Menu” in Section 3-1.

TOP MENU

USER

USER MENU CUSTOMIZE

OPERATION

PAINT

MAINTENANCE

FILE

DIAGNOSIS

Description

USER^a)

You can select desired pages and items from the OPERATION,

PAINT, MAINTENANCE, FILE and DIAGNOSIS menu pages and set

them on the USER MENU CUSTOMIZE menu.

For details, refer to the operation manual supplied with this unit.

USER MENU CUSTOMIZE^a)

OPERATION

This menu is used for editting menu pages and items to be set on the

USER menu.

For details, refer to the operation manual supplied with this unit.

This menu consists of VF screen display items to be set by a camera

operation.

For details, refer to the operation manual supplied with this unit.

PAINT

This menu consists of general paint operation items such as white.

For details, refer to the operation manual supplied with this unit.

MAINTENANCE

This menu consists of paint items used less frequently such as

shading adjustment and items required for the maintenance of the

camera such as system change.

FILE

This menu is used for performing file operations such as saving the

reference file.

DIAGNOSIS

This menu describes the self-diagnosis and VTR status, etc.

a) These menus are displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

HDC-900/950 IMM

3-4 (E)

3-3. OPERATION Menu

MARKER page

Item

Setting

Initial values

The OPERATION menu consists of the items that a

camera operator can set when using this camera, such as

VF screen display setting.

For details, refer to the operation manual supplied with this

unit.

MARKER

ON, OFF

1, 2, 3, 4

ON, OFF

CENTER^a)

SAFETY ZONE^a)

80.0, 90.0, 92.5, 95.0 90.0

ON, OFF OFF

VF DISPLAY page

EFECT

ASPECT MODE^b)

16:9, 15:9, 15:9, 13:9 4:3

4:3, VAR H, VAR V,

1035, VISTA1, VISTA2

Item

Setting

Initial values

3S, ON, OFF

ALL, AT, WRN, OFF

ZOOM

FOCUS

OFF

MASK^a)

ON, OFF

0 to 100

OFF

VAR WIDTH^b)

SAFETY^{a) b)}

0 to 1920 (VAR H)

0 to 1080 (VAR V)

ON, OFF

IRIS

80.0, 90.0, 92.5, 95.0 90.0

WHITE

D5600K

GAIN

OFF

a) Setting ON/OFF of this item is disabled in HDC-900/910. (“[ON], [OFF]”

is displayed.) To set this item to ON or OFF, use the switch located on

the rear side of HDC-900/910. In addition, when connecting CA-905L to

HDC-950/930, setting ON/OFF of this item is also disabled. (“[ON],

[OFF]” is displayed as well.) To set this item ON or OFF, use the switch

located on the rear side of CA-905L.

b) Setting of this item is disabled when setting VF SCAN switch of HDC-

900/910 to 4:3 or when connecting CA-905L to HDC-950/930 and setting

VF SCAN switch of CA905L to 4:3. (“—” is displayed as well.)

SHUTT

BATT

OFF

RETURN

TALK ^a)

MESSAG

GAIN SW page

ALL

a) This item is displayed only when the ROM version on the AT board of

the unit is Ver 1.30 or higher.

Item

Setting

Initial values

LOW

_3, 0, 3, 6, 12

'!' IND page

MIDDLE

HIGH

Item

Setting

[IND]

Initial values

[NORMAL] [IND] [NORMAL]

ON, OFF 1, 2, 3, 4, 5 ON

ON, OFF A, B, C, D, E ON

ZEBRA/VF DTL page

Item

Setting

Initial values

WHITE

D5600K

GAIN

SHUTT

FAN

ON, OFF P, A, B

ON, OFF ON, OFF

ON, OFF L, M, H

ON, OFF ON, OFF

A, B

OFF

ZEBRA

ON, OFF

1, 2, 1 & 2

58 to 82 %

88 to 112 %

ON, OFF

_99 to 99

ON, OFF

ZEBRA1

70 %

100 %

OFF

AUTO1

ZEBRA2

ON, OFF AUTO1,

AUTO2,

VF SKIN GATE^a)

VF DTL^b)

MIN, MAX

EXT

ON, OFF ON, OFF

OFF

FORMAT

ON, OFF 23.98PsF ^a)ON

60I/59.94I, 50I,

59.94I

a) This item is displayed only when the ROM version on the AT board of

the unit is Ver 1.30 or higher.

30PsF/29.97PsF ^a),

25PsF^a),

24PsF/23.98PsF ^a)

b) Setting ON/OFF of this item is disabled in HDC-900/910. (“[ON], [OFF]”

is displayed.) To set this item to ON or OFF, use the switch located on

the rear side of HDC-900/910. In addition, when connecting CA-905L to

HDC-950/930, setting ON/OFF of this item is also disabled. (“[ON],

[OFF]” is displayed as well.) To set this item ON or OFF, use the switch

located on the rear side of CA-905L.

a) HDC-900/950 only.

HDC-900/950 IMM

3-5 (E)

3-3. OPERATION Menu

AUTO IRIS page

Item

Setting

Initial values

WINDOW

1, 2, 3, 4, 5, 6

OVERRIDE

_99 to 99

BATT ALARM page

Item

Setting

Description

DC IN

TYPE ^c)

LITHIUM, DIGITAL,

OTHERS1, OTHERS2,

AC ADP

BEFORE END^d)

END ^d)

c) Setting of this item is disabled in HDC-900/910.

When HKC-T950 is used, select OTHERS1.

d) When HKC-T950 is used, set BEFORE END and END to 13 V.

OTHERS page

Item

Setting

Initial values

D5600K

ON, OFF

OFF

ASSIGNABLE 1

OFF, FAN MAX,

EXTENDER^e)

ASSIGNABLE 2^f)

MIC 1 GAIN

OFF, FAN MAX

OFF

_60, _50, _40, _30, _20 _60

MIC 2 GAIN

_60, _50, _40, _30, _20 _60

LENS VTR S/S^g)

RET2 SW, INCOM1,

INCOM2

RET2 SW

CAM VTR S/S^g)

ZOOM DISP

RET2 SW, INCOM1,

INCOM2

RET2 SW

LEFT

LEFT, RIGHT

e) Setting to "EXTENDER" is enabled in HDC-900/910 only.

f) Setting of this item is disabled in HDC-900/910. (“—” is displayed.)

g) This setting is valid only when the camera control unit is connected, yet

in the camera is used alone, setting is disabled. (“—” is displayed.)

OPERATOR FILE page

Item

Setting

READ (MS → CAM) *1

WRITE (CAM → MS) *1

PRESET

*1 HDC-900/910 :

Execute by pressing the MENU SELECT switch toward the “ENTER”

side.

HDC-950/930 :

Execute by pressing the rotary encoder.

LENS FILE page

Item

Setting

Initial values

FILE

1 to 16

HDC-900/950 IMM

3-6 (E)

3-4. PAINT Menu

The PAINT menu contains overall general paint adjustment items, such as white adjustment.

For details, refer to the operation manual supplied with this unit.

SW STATUS page

(Display is initial values.)

FLARE

: ON

: OFF

: ON

: OFF

GAMMA

BLK GAM

KNEE

WHT CLIP

DETAIL

LVL DEP

SKIN DTL

MATRIX

Item

Setting

Description

FLARE

ON, OFF

Sets the flare correction circuit to ON or OFF.

Sets the gamma correction function to ON or OFF.

Sets the black gamma correction function to ON or OFF.

Sets the knee correction circuit to ON or OFF.

Sets the white clip function to ON or OFF.

GAMMA

BLK GAM

KNEE

WHT CLIP

DETAIL

Sets the function for attaching the detail signal for improving the

resolution to ON or OFF.

LVL DEP

SKIN DTL

MATRIX

ON, OFF

Sets the level dependence function to ON or OFF.

Sets the skin detail function to ON or OFF.

Sets the linear matrix correction function to ON or OFF.

HDC-900/950 IMM

3-7 (E)

3-4. PAINT Menu

VIDEO LEVEL page

(Display is initial values.)

[R] [G] [B] [M]

WHITE :

BLACK :

FLARE :

GAMMA :

V MOD :

FLARE : ON

V MOD : ON

TEST

: OFF

Item

Setting

Description

WHITE

BLACK

FLARE

GAMMA

V MOD

FLARE

V MOD

TEST

_99 to 99

ON, OFF

OFF, 1, 2

Adjusts the white level of R, G, B.

Adjusts the black level of R, G, B and master.

Adjusts the flare level of R, G, B and master.

Adjusts the gamma correction curve of the R, G, B and master.

Adjusts the V modulation shading of R, G, B and master.

Sets the flare correction circuit to ON or OFF.

Sets the V modulation shading to ON or OFF.

Selects the test signal.

OFF : Provides no test signals.

1 :

2 :

Provides the test signal of the sawtooth waveform.

Provides the test signal of the saw tooth waveform of digital

output.

HDC-900/950 IMM

3-8 (E)

3-4. PAINT Menu

GAMMA page

(Display is initial values.)

<GAMMA>

[R] [G] [B] [M]

LEVEL :

COARSE : 0.45

TABLE : STANDARD

GAMMA :

TEST

: OFF

Item

Setting

Description

LEVEL

_99 to 99

Adjusts the gamma correction curve of the R, G, B and master.

Sets the correction curve of the master gamma in 0.05 steps.

COARSE

TABLE

0.35 to 0.90

STANDARD,

USER^*

Selects the gamma table.

STANDARD : Select the standard gamma table which comes standard

on the unit.

USER :

Selects the user gamma table. (Selectable from 5 files.)

1, 2, 3, 4, 5, 6

When STANDARD is selected:

1: INITIAL GAIN 3.5 (equivalent to ENG camcorder)

2: INITIAL GAIN 4.0 LOW (equivalent to EFP camera)

3: INITIAL GAIN 4.0 HIGH (equivalent to EFP camera)

4: INITIAL GAIN 4.0 (equivalent to SMPT-240M)

5: INITIAL GAIN 4.5 (equivalent to ITU-709)

6: INITIAL GAIN 5.0

GAMMA

TEST

ON, OFF

OFF, 1, 2

Sets the gamma correction function to ON or OFF.

Selects the test signal

OFF : Provides no test signals.

1 :

2 :

Provides the test signal of the sawtooth waveform.

Provides the test signal of the sawtooth waveform of digital output.

*: This item is displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

User gamma table is the file that the customers make according to their needs. The gamma or knee may be set to the fixed value

forcibly when the file is made. In this case, the both or either of gamma and knee controls shown below become disabled.

Gamma

. GAMMA page of the PAINT menu

Item : LEVEL, COARSE, GAMMA

Knee

. KNEE page of the PAINT menu

Item : POINT, SLOPE, KNEE

. External switch

AUTO KNEE (OUTPUT/DCC) switch

HDC-900/950 IMM

3-9 (E)

3-4. PAINT Menu

BLK GAMMA page

(Display is initial values.)

RGB

LEVEL :

RANGE :

[R] [G] [B] [M]

: OFF

LEVEL :

RANGE :

: OFF

TEST

: OFF

Item

Setting

Description

RGB LEVEL

RGB RANGE

_99 to 99

Adjusts the black gamma of the R, G, B and master.

1, 2, 3, 4

Sets the upper limit of the video level which the RGB black gamma

affects.

ON, OFF

Sets the RGB black gamma correction function to ON or OFF.

Y LEVEL

Y Range

_99 to 99

Adjusts the Y black gamma to adjust the contrast without changing the

chroma phase of the dark part.

1, 2, 3, 4

Sets the upper limit of the video level which the Y black gamma

affects.

ON, OFF

OFF, 1, 2

Sets the Y black gamma correction function to ON or OFF.

TEST

Selects the test signal.

OFF : Provides no test signals.

1 :

2 :

Provides the test signal of the sawtooth waveform.

Provides the test signal of the sawtooth waveform of digital output.

LOW KEY SAT page (Displays ROM Version lower than 1.30)

(Display is initial values.)

LEVEL

: 0

: OFF

Item

Setting

Description

LEVEL

_99 to 99

Sets the saturation of the dark part.

ON, OFF

Sets the low key saturation function to ON or OFF.

HDC-900/950 IMM

3-10 (E)

3-4. PAINT Menu

SATURATION page (Displays ROM Version 1.30 or higher)

(Display is initial values.)

SATURATION : 0

: OFF

LOW KEY SAT: 0

RANGE: LOW

: OFF

TEST

: OFF

Item

Setting

Description

SATURATION ^a)

_99 to 99

ON, OFF

_99 to 99

Sets the saturation.

Sets the saturation function to ON or OFF.

Sets the saturation of the dark part.

LOW KEY SAT

RANGE

LOW, L MID, H MID, Sets the upper limit of the video level which the low key saturation

HIGH

affects.

ON, OFF

OFF, 1, 2

Sets the low key saturation function to ON or OFF.

TEST

Selects the test signal.

OFF : Provides no test signals.

1 :

2 :

Provides the test signal of the sawtooth waveform.

Provides the test signal of the sawtooth waveform of digital output.

a) This item is not output from the CHARACTER connector of the CNU-700.

HDC-900/950 IMM

3-11 (E)

3-4. PAINT Menu

KNEE page

ROM Version lower than 1.30

ROM Version 1.30 or higher

(Display is initial values.)

<KNEE>

[R] [G] [B] [M]

POINT :

SLOPE :

WHT CLP:

POINT :

SLOPE :

WHT CLP:

KNEE SAT LEVEL

KNEE : ON

WHT CLIP : ON

KNEE

: ON

AUTO KNEE : OFF

KNEE SAT: OFF

WHT CLIP: ON

KNEE SAT :

TEST

: OFF

TEST

Item

POINT

R/G/B/M

SLOPE

R/G/B/M

Setting

Description

_99 to 99

Sets the knee point level when the settings of the auto knee function

of the R, G, B and master are OFF.

_99 to 99

Sets the knee slope level when the settings of the auto knee function

of the R, G, B and master are OFF.

WHT CLP

R/G/B/M

_99 to 99

Sets the white clip level of the R, G, B and master.

KNEE SAT LEVEL^a)_99 to 99

Sets the knee saturation level.

KNEE

ON, OFF

_99 to 99

ON, OFF

OFF, 1, 2

Sets the knee correction circuit to ON or OFF.

Sets the knee saturation function to ON or OFF.

Sets the white clip function to ON or OFF.

Sets the auto knee function to ON or OFF.

Sets the knee saturation level.

KNEE SAT ^a)

WHT CLIP

AUTO KNEE ^b)

KNEE SAT ^b)

Sets the knee saturation function to ON or OFF.

TEST

Selects the test signal.

OFF : Provides no test signals.

1 :

2 :

Provides the test signal of the sawtooth waveform.

Provides the test signal of the sawtooth waveform of digital output.

a) These items are displayed only when the ROM version on the AT board of the unit is lower than Ver 1.30.

b) These items are displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

HDC-900/950 IMM

3-12 (E)

3-4. PAINT Menu

DETAIL 1 page

(Display is initial values.)

[M] [WHT][BLK]

LEVEL

LIMITER

CRISPEN

HV RATIO :

FREQ

LVL DEP

DETAIL

: ON

LVL DEP

Item

Setting

Description

LEVEL

_99 to 99

Sets the general level of the detail signal.

LIMITER

_99 to 99

Sets the level for clipping the excessive detail signal.

M/WHT/BLK

CRISPEN

_99 to 99

Sets the level for suppressing the noise components contained in the

detail signal.

HV RATIO

FREQ

_99 to 99

ON, OFF

Sets the ratio between H detail signal and V detail signal.

Sets the frequency of the H detail signal.

LVL DEP

DETAIL

Sets the level for suppressing the detail amount in the dark part.

Sets the function for attaching the detail signal for improving the

resolution to ON or OFF.

LVL DEP

ON, OFF

Sets the level depend function to ON or OFF.

DETAIL 2 page

(Display is initial values.)

KNEE APERTURE :

: OFF

Item

Setting

Description

KNEE APERTURE _99 to 99

Sets the knee aperture^a)level.

ON, OFF

Sets the knee aperture^a)function to ON or OFF.

a) This function compensates for decreases by the knee aperture in the detail level at the high luminance level part of the camera subject.

HDC-900/950 IMM

3-13 (E)

3-4. PAINT Menu

SKIN DETAIL page

(Display is initial values.)

SKIN DTL : OFF

SKIN GATE: OFF

[1]

[2]

[3]

OFF

CH SW : (ON) OFF

GATE : ON

OFF

PHASE : AUTO AUTO AUTO

WIDTH : 30

SAT : -89

LEVEL :

-89

Item

Setting

Description

SKIN DTL

ON, OFF

When this setting is ON, the setting [1] of the channel 1 is always set

ON. Sets the skin detail function to ON or OFF.

SKIN GATE ^b)

CH SW

ON, OFF

Sets the zebra indication of the skin tone detail portion to ON or OFF.

Sets each channel of the skin detail function to ON or OFF.

Channel 1 is fixed to ON.

GATE

ON, OFF

AUTO^a)

Sets each channel of the skin gate function to ON or OFF.

PHASE

Set automatically the region of each channel the skin detail function affects.

0d to 359d

Sets the center phase of the chroma phase the skin tone detail function

affects to each channel.

WIDTH

0d to 90d

Adjusts the chroma phase width of the skin tone detail function to each

channel.

SAT

_99 to 99

Adjusts the saturation level of the skin tone detail function to each channel.

Sets the skin tone detail amount to each channel.

LEVEL

_99 to 99

a) Method of executing AUTO

HDC-900/910 : 1. Set the cursor to the AUTO and press the MENU SELECT switch toward the “ENTER” side, then the square-

shaped zebra pattern is displayed on the viewfinder.

2. Set the zebra pattern to the color to be given the effect of the skin tone detail and press the MENU SELECT

switch toward the “ENTER” side. to select the phase.

HDC-950/930 : 1. Set the cursor to the AUTO and press the rotary encoder, then the square-shaped zebra pattern is displayed on

the viewfinder.

2. Set the zebra pattern to the color to be given the effect of the skin tone detail and press the rotary encoder to

select the phase.

b) This item is displayed only when the ROM version on the AT board of the unit is lower than Ver 1.30.

HDC-900/950 IMM

3-14 (E)

3-4. PAINT Menu

USER MATRIX page

(Display is initial values.)

[-R] [-G] [-B]

R :

G :

B :

MATRIX: OFF

PRESET: ON

: SMPTE-240M

USER MATRIX : OFF

MULTI MATRIX: OFF

Item

Setting

Description

R-G, R-B,

G-R, G-B,

B-R, B-G,

MATRIX ^a)

PRESET ^a)

_99 to 99

ON, OFF

Sets the linear matrix coefficient for each R-G, R-B, G-R, G-B, B-R,

and B-G.

Sets the linear matrix correction function to ON or OFF.

Sets the linear matrix correction coefficient set at factory to ON or

OFF.

(When the MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

SMPTE-240M,

ITU-709,

Selects the linear matrix correction coefficient set at factory.

SMPTE-WIDE,

NTSC,

EBU

ITU-609

USER MATRIX ^a)

MULTI MATRIX ^a)

ON, OFF

Sets the linear matrix correction function set by the user to ON or

OFF.

(When the MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

ON, OFF

Sets the multi matrix correction function to ON or OFF.

(When the MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

USER MATRIX

USER MATRIX SW

MATRIX SW

LINEAR MATRIX

CIRCUIT

(+REFERENCE FILE USER MATRIX)

MULTI MATRIX SW

PRESET MATRIX SW

OHB MATRIX SW

MULTI MATRIX

(+REFERENCE FILE MULTI MATRIX)

PRESET MATRIX

OHB MATRIX

(+OHB FILE OHB MATRIX)

USER MATRIX :

MULTI MATRIX :

Linear matrix that can change R-G and R-B in the conventional camera.

Linear matrix that divides the chroma phase width of the linear matrix into 16 segments and can adjust each

individually.

PRESET MATRIX : Addition of the linear matrix value fixed in the standard specification.

OHB MATRIX : Linear (multi) matrix for matching the color between the cameras.

HDC-900/950 IMM

3-15 (E)

3-4. PAINT Menu

MULTI MATRIX page

(Display is initial values.)

PHASE :

HUE

SAT

ALL CLEAR

MATRIX : OFF

PRESET : ON

: SMPTE-240M

USER MATRIX : OFF

MULTI MATRIX: OFF

Item

Setting

Description

PHASE

0, 23, 45, 68, 90,

113, 135, 158, 180,

203, 225, 248, 270,

293, 315, 338

Sets the angle that varies the multi matrix correction function.

(sixteen-axis mode)

HUE

_99 to 99

Adjusts the color phase the multi matrix correction function affects in

every sixteen-axis mode.

SAT

Adjusts the saturation level the multi matrix correction function affects in

every sixteen-axis mode.

ALL CLEAR

Clears the HUE and SAT values in each phase to 0.

(The values in the reference file are not cleared.)

MATRIX^a)

PRESET ^a)

ON, OFF

Sets the liner matrix correction function to ON or OFF.

Sets the multi matrix correction coefficient set at the factory to ON or

OFF. (When MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

SMPTE-240M,

ITU-709,

Selects the multi matrix correction coefficient set at the factory.

SMPTE-WIDE,

NTSC,

EBU

ITU-609

USER MATRIX ^a)

MULTI MATRIX ^a)

ON, OFF

Sets the multi matrix correction function set by the user to ON or OFF.

(When MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

ON, OFF

Sets the multi matrix correction function to ON or OFF.

(When MATRIX setting is OFF, this setting is unavailable, “- - -” is

displayed showing invalid.)

USER MATRIX

USER MATRIX SW

MATRIX SW

LINEAR MATRIX

CIRCUIT

(+REFERENCE FILE USER MATRIX)

MULTI MATRIX SW

PRESET MATRIX SW

OHB MATRIX SW

MULTI MATRIX

(+REFERENCE FILE MULTI MATRIX)

PRESET MATRIX

OHB MATRIX

(+OHB FILE OHB MATRIX)

USER MATRIX :

MULTI MATRIX :

Linear matrix that can change R-G and R-B in the conventional camera.

Linear matrix that divides the chroma phase width of the linear matrix into 16 segments and can adjust each

individually.

PRESET MATRIX : Addition of the linear matrix value fixed in the standard specification.

OHB MATRIX : Linear (multi) matrix for matching the color between the cameras.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-16 (E)

3-4. PAINT Menu

SHUTTER page

(Display is initial values.)

SHUTTER : OFF

: 1/100

ECS FREQ: 30.0Hz

S-EVS : OFF

Item

Setting

Description

SHUTTER

ON, OFF

Sets the shutter/ECS mode to ON or OFF.

Table below^a)

Sets the shutter speed.

(The selectable shutter speed varies with each format.)

ECS FREQ

S-EVS

Table below ^b)

Sets the ECS frequency.

(The selectable ECS frequency variable region varies with each format.)

ON, OFF

Sets the S-EVS mode to ON or OFF.

0 to 100 %

Sets the S-EVS. (When the format setting 30PsF, 29.97PsF, 25PsF,

24PsF and 23.98PsF, this setting is unavailable. “- - -” is displayed

showing invalid.)

For the HDC-910/930, this setting is “100 %” only.

a) Shutter speed setting

Format

Shutter speed

60I/59.94I

1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000

50I

1/60, 1/125, 1/250, 1/500, 1/1000, 1/2000

30PsF/29.97PsF^*

25PsF^*

1/40, 1/50, 1/60, 1/120, 1/125, 1/250, 1/500, 1/1000

1/33, 1/50, 1/60, 1/100, 1/125, 1/250, 1/500, 1/1000

1/32, 1/48, 1/50, 1/60, 1/96, 1/125, 1/250, 1/500, 1/1000

24PsF/23.98PsF^*

* : For the HDC-910/930, this setting is unavailable.

b) ECS frequency setting

HDC-900/950 :

Format

ECS

60I/59.94I

50I

30.0 to 4300 Hz

25.0 to 4700 Hz

30.0 to 2700 Hz

25.0 to 2300 Hz

24.0 to 2200 Hz

30PsF/29.97PsF

25PsF

24PsF/23.98PsF

HDC-910/930 :

Format

ECS

60I/59.94I

50I

60.0 to 4300 Hz

50.0 to 4700 Hz

HDC-900/950 IMM

3-17 (E)

3-4. PAINT Menu

SCENE FILE page

1 2 3 4 5

STORE

STANDARD

READ (MS CAM)

WRITE (CAM MS)

FILE ID:

CAM CODE:

DATE:

Item

Setting

Description

1, 2, 3, 4, 5

Saves and calls the scene file (the data painted in accordance with the

shooting scene.) (Same as the SCENE FILE page in the FILE menu.)

STORE

STANDARD

Returns the current paint adjustment amount and switch settings to the

reference values.

READ (MS → CAM)

WRITE (CAM → MS)

FILE ID

Reads out five scene files from the memory stick to the memory of camera unit.

Writes five scene files stored in the memory of camera unit to the memory stick.

Writes comments to a scene file to be stored to the memory stick.

CAM CODE

Only displays the model name of the scene file saved in the memory stick.

Only displays the date when the scene file was created in the memory stick.

DATE

HDC-900/910

How to save

1. Set “→” to STORE and press the MENU SELECT switch toward the “ENTER” side, then “STORE

NO?”will blink.

2. Select the file No. (1 to 5) for saving.

(If data is already saved, the data will be replaced with new one.)

How to call

Set “→” to the file No. to be called up and press the MENU SELECT switch toward the “ENTER” side.

During calling up, the number is highlighted, and to cancel the operation, press the MENU SELECT

switch toward the “ENTER” side during the highlighting.

HDC-950/930

How to save

1. Set “→” to STORE and press the rotary encoder, then “STORE NO?”will blink.

2. Select the file No. (1 to 5) for saving.

(If data is already saved, the data will be replaced with new one.)

How to call

Set “→” to the file No. to be called up and press the rotary encoder.

During calling up, the number is highlighted, and to cancel the operation, press the rotary encoder during

the highlighting.

HDC-900/950 IMM

3-18 (E)

3-5. MAINTENANCE Menu

This menu consists of paint items used less frequently such as shading adjustment and items required for

the camera maintenance such as system change.

AUTO SETUP page

(Display is initial values.)

AUTO BLACK

AUTO WHITE

AUTO LEVEL

TEST

: OFF

Item

Setting

Description

AUTO BLACK

AUTO WHITE

AUTO LEVEL

TEST

Starts the automatic black balance adjustment.

(Pressing the rotary encoder during the execution, the execution is

canceled.)

Starts the automatic white balance adjustment.

(Pressing the rotary encoder during the execution, the execution is

canceled.)

Starts the automatic level adjustment of the camera circuit.

(Pressing the rotary encoder during the execution, the execution is

canceled.)

OFF, 1, 2

Selects the test signal.

OFF : No test signal is available.

1 :

2 :

Provides the test signal of the sawtooth wave.

Provides the test signal of the sawtooth wave of digital output.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

WHITE SHADING page

(Display is initial values.)

[R] [G] [B] [M]

V SAW :

V PARA :

H SAW :

H PARA :

WHITE :

V MOD :

V MOD

: ON

Item

Setting

Description

V SAW R/G/B

V PARA R/G/B

H SAW R/G/B

H PARA R/G/B

WHITE R/G/B

V MOD R/G/B

V MOD

_99 to 99

ON, OFF

Adjusts the white shading V SAW correction amount of the R,G,B master.

Adjusts the white shading V PARA correction amount of R,G,B.

Adjusts the white shading H SAW correction amount of R,G,B.

Adjusts the white shading H PARA correction amount of R,G,B.

Adjusts the white level of R,G,B.

Adjusts the V modulation shading of R,G,B and master.

Sets the V modulation shading function to ON of OFF.

HDC-900/950 IMM

3-19 (E)

3-5. MAINTENANCE Menu

BLACK SHADING page

(Display is initial values.)

[R] [G] [B] [M]

V SAW :

V PARA :

H SAW :

H PARA :

BLK SET:

BLACK :

MASTER GAIN : 0dB

Item

Setting

Description

V SAW R/G/B

V PARA R/G/B

H SAW R/G/B

H PARA R/G/B

BLK SET R/G/B

BLACK R/G/B/M

MASTER GAIN

_99 to 99

Adjusts the black shading V SAW correction amount of the R,G,B master.

Adjusts the black shading V PARA correction amount of R,G,B.

Adjusts the black shading H SAW correction amount of R,G,B.

Adjusts the black shading H PARA correction amount of R,G,B.

Adjusts the black set correction amount of R,G,B.

Adjusts the black level of the R,G,B and master.

_3, 0, 3, 6, 12 dB

Sets the master gain.

OHB MATRIX page

(Display is initial values.)

PHASE : 0

HUE

SAT

: 0

ALL CLEAR

MATRIX

: OFF

OHB MATRIX: OFF

Item

Setting

Description

PHASE

0, 23, 45, 68, 90,

Set the region the OHB matrix correction function affects.

(sixteen-axis mode)

113, 135, 158, 180,

203, 225, 248, 270,

293, 315, 338

HUE

_99 to 99

Adjusts the color phase the OHB matrix correction function affects in

every sixteen-axis mode.

SAT

Adjusts the saturation level the OHB matrix correction function affects in

every sixteen-axis mode.

ALL CLEAR

Clears the HUE and SAT values in each phase to 0.

(The values in the OHB file are not cleared.)

MATRIX

ON, OFF

Sets the linear matrix correction function ON or OFF.

Sets the OHB matrix correction function ON or OFF.

OHB MATRIX

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-20 (E)

3-5. MAINTENANCE Menu

AUTO IRIS page

ROM Version lower than 1.30

ROM Version 1.30 or higher

(Display is initial values.)

WINDOW

AUTO IRIS : OFF

OVERRIDE :

IRIS LEVEL:

WINDOW

OVERRIDE :

IRIS LEVEL:

APL RATIO : 80

IRIS GAIN :

APL RATIO : 80

IRIS GAIN :

IRIS CLOSE: OFF

Item

Setting

Description

AUTO IRIS^b)

WINDOW

ON, OFF

Sets the auto iris function to ON to OFF.

Selects the auto iris window.^a)

1, 2, 3, 4, 5, 6

_99 to 99

OVERRIDE

Sets the reference value of the auto iris level by ±2 focus.

_99 (2 iris nearly closed) ↔ 99 (2 iris nearly open)

IRIS LEVEL

APL RATIO

_99 to 99

Sets the auto-iris level.

_99 to 99

Sets the method of detecting the light amount of the auto iris.

_99 (Peak light detection ) ↔ 99 (Average value detection of whole screen)

IRIS GAIN

_99 to 99

Sets the iris gain.

IRIS CLOSE^b)

ON, OFF

Sets the iris close function to ON or OFF.

Setting

screen

indicates the auto iris window frame.

b) These items are displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

CAM ID/DATE page

(Display is initial values.)

CAM ID :

DATE/TIME

2000/04/30 08:32

Item

Setting

Description

CAM ID

Sets the camera ID of less 14 characters consisting of alphanumeric,

symbols and spaces.

DATE/TIME

Sets the present date and time.

[Reference]

The way of indicating date is changeable.

Refer to DATE TYPE of OTHER2 page in MAINTENANCE menu.

HDC-900/950 IMM

3-21 (E)

3-5. MAINTENANCE Menu

MULTI FORMAT page

HDC-900/950

HDC-910/930

(Display is initial values.)

CURRENT 59.94I

CURRENT 59.94I

: 59.94I

60I

50I

60I

50I

59.94I

30PsF

29.97PsF

25PsF 24PsF

23.98PsF

Item

Setting

Description

Displays the format being currently selected.

CURRENT

NEXT ^a)

The currently selected format is highlighted in the line below.

Selects the format when the power is turned on next time.

HDC-900/910 :

A turn of the MENU SELECT control shifts the portion highlighted.

Press the MENU SELECT switch toward the “ENTER” side for determi-

nation. (The highlighted portion does not shift to the *** portion.)

HDC-950/930 :

A turn of the rotary encoder shifts the portion highlighted. Press the

rotary encoder for determination. (The highlighted portion does not shift

to the *** portion.)

a) This setting is valid only when the camera is used alone. When the camera control unit is connected, the camera control unit setting

takes a priority.

SDI page (Displays ROM Version lower than 1.30)

OUT PUT page (Displays ROM Version 1.30 or higher)

ROM Version lower than 1.30

ROM Version 1.30 or higher

(Display is initial values.)

<SDI>

PROMPTER

: OFF

PROMPTER

: OFF

BNC SDI OUT: OFF

LINER EXP : OFF

Item

Setting

Description

PROMPTER ^a)

BNC SDI OUT ^b)

LINER EXP ^c)

ON, OFF

ON : Prompter signal is output at PROMPTER OUT connector

OFF : No prompter signal is output

ON : SDI signal is output at HD SERIAL DIGITAL OUT connector

OFF : No SDI signal is output

ON : Improves the reproducibility of high-luminance part in PsF

format.

OFF : Standard setting.

a) This setting is valid only when the camera control unit is connected, yet in the camera is used alone, setting is disabled. (“—” is

displayed.)

b) This setting is valid only when the camera is used alone. When the camera control unit is connected, setting is always ON. (“—” is

displayed.)

c) This can be selected when the VA-223 board is installed.

HDC-900/950 IMM

3-22 (E)

3-5. MAINTENANCE Menu

VTR 26PIN page

(Display is initial values.)

CABLE COMP: OFF

VIDEO SEL : MAIN(RGB)

MAIN VIDEO ADJUST

G :

B :

R :

Y :

Pb :

Pr :

Item

Setting

Description

Selects the VTR (26P) cable compensation

CABLE COMP

VIDEO SEL

OFF, 25 m, 50 m

MAIN (RGB),

MAIN (YPbPr),

RET (YPbPr) ^a)

Selects the video signal to be output to the VTR (26 p) OUT connector.

RET (YPbPr) outputs the return video signal input from the camera

control unit.

_30 to 30

Corrects the output level to the VTR (26 P) OUT connector

a) This setting is valid only when the camera control unit is connected.

BATT ALARM page

(Display is initial values.)

DC IN

TYPE : AC ADP

BEFORE END : --

END

: --

Item

DC IN TYPE ^a)

Setting

Description

LITHIUM, DIGITAL,

OTHERS1^b), OTHERS2 ^b)

AC ADP ^c)

Selects the power running in the DC IN connector.

By this setting, the battery alarm voltage indication in accordance with

the features of the battery or the power supply becomes possible.

BEFORE END 11.0 to 17.0 V

Sets the alarm voltage indicating that the DC power is wearing out.

When the AC ADP is selected, this setting is unavailable “- - -” is

displayed showing invalid.

END

11.0 to 17.0 V

Sets the alarm voltage indicating that the DC power has worn out.

When the AC ADP is selected, this setting is unavailable “- - -” is

displayed showing invalid.

a) Setting change of this item is disabled in HDC-900/910.

b) These can be selected when using batteries other than LITHIUM, DIGITA L, AC ADP and the power supply.

c) This can be selected when using an AC/DC power supply of AC-550 and so on.

HDC-900/950 IMM

3-23 (E)

3-5. MAINTENANCE Menu

OTHERS1 page

(Display is initial values.)

FAN MODE

H PHASE

CHU BARS

: AUTO1

: OFF

Item

Setting

Description

FAN MODE

AUTO1,

AUTO2,

MIN, MAX

Sets the fan mode.

AUTO1 : normal mode

AUTO2 : silent mode

MIN :

MAX :

minimum rotation mode

maximum rotation mode

H PHASE

_3072 to 1023

Adjusts the H phase.

CHU BARS

ON, OFF

Sets the CHU BARS to ON or OFF.

HDC-900/950 IMM

3-24 (E)

3-5. MAINTENANCE Menu

OTHERS2 page

(Display is initial values.)

MENU RESUME : OPE MENU

DATE TYPE : 1 Y/Mn/D

WHITE MEMORY: 2

COLOR BAR

EXT F NO

: FULL 16:9

: CONTROL

TRUNK LINE : (1CH)

Item

MENU RESUME

Setting

Description

OPE MENU,

OFF, ALL

Sets the menu screen displayed when starting the menu.

OPE MENU : Starts to display from the page in the operation menu,

which was displayed at powering off of the previous time.

Starts to display from the first page (VF DISPLAY) in the

operation menu.

OFF :

ALL :

Displays the menu screen, which was displayed at

powering off of the previous time.

To display the TOP menu, refer to Section 3-2.

DATE TYPE

1 to 6

Sets the date.

1: Y/Mn/D Year/Month/Date (Month should be showed by the figure.)

2: Mn/D

3: D/M/Y Date/Month/Year

4: D/M Date/Month

5: M/D/Y Month/Date/Year

6: M/D Month/Date

Month/Date (Month should be showed by the figure.)

WHITE MEMORY

COLOR BAR

2, 10

Sets the number of white balance memory.

2: White balance memory can be set to A and B of WHITE BAL switch

(total 2).

10:White balance memory can be set to A and B of each CC filter and

WHITE BAL switch (total 8).

FULL 16 : 9 ,

SMPTE 16 : 9 ,

FULL 4 : 3 ,

Sets the color bar.

FULL 16 : 9:

SMPTE 16 : 9: 75 % color bar of 16 : 9

FULL 4 : 3: 100 % color bar of 4 : 3

100 % color bar of 16 : 9

SMPTE 4 : 3

SMPTE 4 : 3: 75 % color bar of 4 : 3

EXT F NO ^a)

CONTROL,

POSITION

Selects the iris indication when the lens extender (x2) to ON.

CONTROL : Indicated by the control value from the camera.

POSITION : Indicated by the return value from the lens.

TRUNK LINE^{a) b)}

(1CH)

Only displays the trunk line mode set by the camera control unit.

a) These items are displayed only when the ROM version on the AT board of the unit is Ver 1.30 or higher.

b) This item is displayed only when the camera control unit is connected.

HDC-900/950 IMM

3-25 (E)

3-5. MAINTENANCE Menu

T ADP ADJ page (Displays ROM Version 1.20 or higher)

(Display is initial values.)

[R] [G] [B]

VSAW OFST: -16 -16 -16

CABLE

10M

STORE DATA

Item

Setting

Description

VSAW OFST

_50 ~ +50, - - -

Adjusts V SAW correction amount when HKC-T950 is connected.

When HKC-T950 is not connected, this setting is disable, “- - -” is

displayed showing invalid.

CABLE

10M, 25M, 50M

Displays the cable length being currently connected.

Stores the adjustment value to cable adaptor.

STORE DATA

Execute by pressing

the rotary encoder

HDC-900/950 IMM

3-26 (E)

3-6. FILE Menu

File menu is used to operate the file such as saving the reference file.

OPERATOR FILE page

READ (MS CAM)

WRITE(CAM MS)

PRESET

STORE PRESET FILE

FILE ID:

CAM CODE

DATE

Item

Setting

Description

READ

(MS → CAM)

Reads the operator file from the memory stick.

WRITE

(CAM → MS)

Saves the operator file in the memory stick.

RESET

Reset the operator file items to the preset values.

STORE PRESET

FILE

values of the operator file.

FILE ID

Writes comments to a file.

CAM CODE

DATE

Displays the camera name of the file created.

Displays the date when the file was created.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-27 (E)

3-6. FILE Menu

SCENE FILE page

1 2 3 4 5

STORE

STANDARD

READ (MS CAM)

WRITE (CAM MS)

FILE ID:

CAM CODE

DATE

Item

Setting

Description

1, 2, 3, 4, 5

Saves and calls the scene file (the data painted in accordance with the

shooting scene.) (Same as the SCENE FILE page in the PAINT menu.)

STORE

STANDARD

Returns the current paint adjustment amount and switch settings to the

reference values.

READ (MS → CAM)

WRITE (CAM → MS)

FILE ID

Reads out five scene files from the memory stick to the memory of camera unit.

Writes five scene files stored in the memory of camera unit to the memory stick.

Writes comments to a scene file to be stored to the memory stick.

CAM CODE

Only displays the model name of the scene file saved in the memory stick.

Only displays the date when the scene file was created in the memory stick.

DATE

HDC-900/910

How to save

1. Set “→” to STORE and press the MENU SELECT switch toward the “ENTER” side, then “STORE

NO?”will blink.

2. Select the file No. (1 to 5) for saving.

(If data is already saved, the data will be replaced with new one.)

How to call

Set “→” to the file No. to be called up and press the MENU SELECT switch toward the “ENTER” side.

During calling up, the number is highlighted, and to cancel the operation, press the MENU SELECT

switch toward the “ENTER” side during the highlighting.

HDC-950/930

How to save

1. Set “→” to STORE and press the rotary encoder, then “STORE NO?”will blink.

2. Select the file No. (1 to 5) for saving.

(If data is already saved, the data will be replaced with new one.)

How to call

Set “→” to the file No. to be called up and press the rotary encoder.

During calling up, the number is highlighted, and to cancel the operation, press the rotary encoder during

the highlighting.

HDC-900/950 IMM

3-28 (E)

3-6. FILE Menu

REFERENCE page

STORE FILE

STANDARD

READ(MS CAM)

WRITE(CAM MS)

FILE ID:

CAM CODE

DATE

Item

Setting

Description

STORE FILE

STANDARD

READ (MS → CAM)

WRITE (CAM → MS)

FILE ID

Registers the adjustment values of each item as the reference file.

Returns the data registered in the reference file to the reference value.

Reads out reference file from the memory stick to the memory of camera unit.

Writes reference file stored in the memory of camera unit to the memory stick.

Writes comments to a reference file to be stored to the memory stick.

Only displays the model name of the reference file saved in the memory stick.

Only displays the date when the reference file was created in the memory stick.

CAM CODE

DATE

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

USER GAMMA page (Displays ROM Version 1.30 or higher)

READ (MS CAM)

FILE ID:

CAM CODE

DATE

Item

Setting

Description

READ (MS → CAM) *1

Reads the user gamma file from the memory stick to the memory of the

camcorder.

FILE ID

Writes comments to a user gamma file to be stored to the memory stick.

CAM CODE

Only displays the model name that created the user gamma file saved in the

memory stick.

DATE

Only displays the date when the user gamma file was created in the memory

stick.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-29 (E)

3-6. FILE Menu

LENS FILE page

(Display is initial values.)

STORE FILE

NO. : 1

NAME : HA14x8

F NO : F2.0

CENTER MARKER

H POS: 0

V POS: 0

STORE CENTER

Item

Setting

Description

STORE FILE

Registers the adjustment values for each item (exc. the center marker position)

as the lens file.

No.

1to 16

Selects the file matching with the mounted lens from the sixteen lens files

Displays the lens file name in accordance with the No. (1 to 16) selected.

Sets the open edge F value of the lens.

NAME

F NO

H POS

F1.0 to F3.4

_20 to 20

Sets the center marker position (Horizontal)

20 (right) ↔ _20 (left)

V POS

_20 to 20

Sets the center marker position (Vertical)

20 (lower) ↔ _20 (upper)

STORE CENTER

Registers the center marker position in the lens file being selected.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

OHB FILE page

STORE FILE

Item

Setting

Description

STORE FILE

Stores the OHB file.

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-30 (E)

3-6. FILE Menu

FILE CLEAR page

(Display is initial values.)

PRESET OPERATOR

REFERENCE(ALL)

10 SEC CLEAR: OFF

LENS(CURRENT)

OHB WHITE SHAD

OHB BLACK SHAD

OHB ND OFFSET

OHB MATIX

MS FORMAT

Item

Setting

Description

PRESET

OPERATOR

Returns the preset value of the operator file set by the user to the

original value at factory setting.

REFERENCE (ALL) *1

Returns each adjustment value registered in the reference file to the

original values at factory setting.

10 SEC CLEAR

ON, OFF

HDC-900/910 :

Sets ON or OFF the function to clear the reference value by continuing

to push the MENU SELECT switch toward the “ENTER” side for more

than ten seconds with the cursor set to the reference item and “?”

blinking.

HDC-950/930 :

Sets ON or OFF the function to clear the reference value by continuing

to push the rotary encoder for more than ten seconds with the cursor

set to the reference item and “?” blinking.

The setting returns to OFF when the unit is powered off.

LENS (CURRENT) *1

Returns the lens file being selected to the original value at factory

setting.

OHB WHITE SHAD

OHB BLACK SHAD

OHB ND OFFSET

OHB MATRIX

Clears the white shading in the OHB file to 0.

Clears the black shading in the OHB file to 0.

Clears the ND offset in the OHB file to 0.

Clears the matrix in the OHB file to 0.

Formats the memory stick.

MS FORMAT

*1 HDC-900/910 : Execute by pressing the MENU SELECT switch toward the “ENTER” side.

HDC-950/930 : Execute by pressing the rotary encoder.

HDC-900/950 IMM

3-31 (E)

3-7. DIAGNOSIS Menu

The DIAGNOSIS menu displays the self-diagnosis of every plug-in board and photo-receptive condition

of the optical connector, etc.

SDI page

<SDI>

OPTICAL LEVEL:GREEN

Item

Setting

Description

OPTICAL LEVEL

GREEN,

YELLOW,

RED,

NO SIGNAL

___

Displays a photo-receptive condition of the optical connector

GREEN :

YELLOW :

RED :

Normal (_17 dBm ^*or more)

Normal (_17 to _20 dBm^*)

Abnormal (less than _20 dBm^*)

NO SIGNAL : Out of sync with HDCU

___ :

When the camera is used alone

^*0 dBm = 1 mW

If “RED” is indicated, be sure to clean the optical connector and optical/electrical cable. If “YELLOW” is

indicated, cleaning them is recommended. For details on how to clean, refer to Section 2-1.

HDC-900/950 IMM

3-32 (E)

3-7. DIAGNOSIS Menu

BOARD STATUS page

ROM:V1.00

OHB :OK

SG :OK

:OK

AT :OK

AU :OK

RE :OK

PS :OK

DPR :OK

VDA :OK

DAD :OK

SDI :OK

DAP :OK

Item

Setting

Description

ROM

OHB

Indicates the ROM version for IC1/AT-130 board

Displays the self-diagnosis status of the CCD block. ^b)

Displays the self-diagnosis status of the VA board.

Displays the self-diagnosis status of the DPR board.

Displays the self-diagnosis status of the VDA board.

Displays the self-diagnosis status of the DAD board.

Displays the self-diagnosis status of the SDI board.

Displays the self-diagnosis status of the DAP board.

Displays the self-diagnosis status of the SG board.

Displays the self-diagnosis status of the AT board.

Displays the self-diagnosis status of the AU board.

Displays the self-diagnosis status of the RE board.

Displays the self-diagnosis status of the PS board.

OK, NG

DPR

VDA

DAD

SDI

DAP

PS ^a)

a) This setting is valid only when the camera control unit is connected, yet in the camera is used alone, setting is disabled. (“—” is

displayed.)

b) When HKC-T950 is connected, it judges based on status of the connection cable, communication state between the CCD block

adaptor and cable adaptor and so on in addition to the diagnosis in the camera that is being used alone.

When “NG” is indicated, contact your local Sony Sales Office.

HDC-900/950 IMM

3-33 (E)

Section 4

File System

The HDC-900/910/950/930 are equipped with various file systems for managing data.

4-1. File Structure

The following six types of files are available.

1. Operator File

Stores the items displayed on the viewfinder and switch settings for camera operator. This file is

stored in the memory stick, yet the video data (paint data) cannot be stored.

2. Preset Operator File

Stores the standard state of operator file items.

This file is stored in the camera, yet video data (paint data) cannot be stored.

3. Scene File

Stores the temporary video setting data according to the scene. This file is stored in the camera and

memory stick.

4. Reference File

Stores the custom paint data adjusted by the video engineer. This file is stored in the camera and

memory stick.

5. Lens File

Used for compensation of the deviation which generates by switching the lens extender from OFF to

ON and for compensation of the difference in the characteristics between lenses. This file is stored in

the camera.

6. OHB File

Used for adjustment of the CCD block maintenance. This file is stored in the camera.

Scene File

Refer to Section 4-8. “File Items”.

When STANDARD

Lens File

is executed

When lens extender setting is OFF, Flare R/G/B and

V Modulation Shading R/G/B/Master can be stored.

When lens extender setting is ON, White R/B, Flare R/G/B and

V Modulation Shading R/G/B/Master can be stored.

Output to

hardware^(*1)

Reference File

Refer to Section 4-8. “File Items”.

OHB File

R/G/B for each White Shading H SAW, H PARA, V SAW, VPARA can be stored.

R/G/B for each Black Shading H SAW, H PARA, V SAW, V PARA can be stored.

And OHB matrix and the ND offset can be stored.

Factory-set value 0

Fig. 4-1. Structure of Paint Related Files

(*1): The additional data of each file is sent to each circuit on the unit.

HDC-900/950 IMM

4-1 (E)

4-2. Operator File

Data is stored in the memory stick using the setup menu. As for the items to be stored, refer to Section 4-

8,“ File Items”.

. As for the setup menu, refer to Section 3.

. Operator files stored in the memory stick will not be read when the power is just turned ON. This file

will only be read when READ is executed at the setup menu.

. The current operator file data is retained even when the power is turned off by the power switch.

. Before storing the file in the memory stick, make sure that the LOCK switch on the memory stick is in

OFF position.

Storing the Operator File in the Memory Stick (Refer to step 1 of Fig. 4-2.)

Set the setup menu as follows, and store the current status in the memory stick.

Reading the Operator File from the Memory Stick (Refer to step 2 of Fig. 4-2.)

Set the setup menu as follows.

Memory stick

Reading

(Step 2)

Storing

(Step 1)

Camera unit

Preset

reading

(Step 3)

Preset

initialization

(Step 5)

Current Operator

Preset factory-set

value

Preset Operator File

File Data

Preset

storing

(Step 4)

Output to hardware

Fig. 4-2. Operating Procedure for Operator Files

HDC-900/950 IMM

4-2 (E)

4-3. Preset Operator File

The preset operator file is designed to store the standard values of the operator file items. There are two

ways of calling the preset operator file; calling from the setup menu or reading at power ON. The items

which can be stored on file are the same as Operator File.

As for the setup menu, refer to Section 3.

Calling Using the Setup Menu (Refer to step 3 of Fig. 4-2.)

Set the setup menu as follows.

[OPERATION] → [OPERATOR|FILE] → [PRESET]

Calling without Using the Setup Menu (Refer to step 3 of Fig. 4-2.) (For HDC-950/930)

Set the WHITE BAL switch to “PRST”, and while pushing the AUTO W/B BAL switch to the WHT

side, set the POWER switch to ON.

Storing the Preset Values (Refer to step 4 of Fig. 4-2.)

The items of the preset values can be changed using the setup menu.

Set the setup menu as follows.

[FILE] → [OPERATOR|FILE] → [STORE|PRESET|FILE]

Then, current status can be stored in the camera as Preset Operator File.

Initializing the Preset Values (Refer to step 5 of Fig. 4-2.)

Set the setup menu as follows to initialize the changed preset items to the factory-set data.

[FILE] → [FILE|CLEAR] → [PRESET|OPERATOR]

HDC-900/950 IMM

4-3 (E)

4-4. Registering the Scene File

The scene file is used for storing temporary video adjustment values according to the scene. 5 files can be

stored and the data will be stored in the camera and memory stick. The data can be stored using a setting

menu or MSU (master setup unit).

Scene files can be copied between cameras using the memory stick.

As for the items to be stored, refer to Section 4-8,“ File Items”.

. Scene files are files for storing the differences from the reference file. Therefore when the reference file

is changed, output of the scene file item corresponding with the item changed in the reference file is

also changed.

. As for the setup menu, refer to Section 3.

. Before storing the file in the memory stick, make sure that the LOCK switch on the memory stick is in

OFF position.

Storing Using Setup Menu (Refer to step 1 of Fig.4-3.)

(1) Set the setup menu as follows.

[PAINT] → [SCENE|FILE] → [STANDARD]

(2) Change the scene file item to the desired value.

(3) Set the setup menu as follows.

[PAINT] → [SCENE|FILE] → [STORE]

Select the scene file number to be stored.

Calling Using Setup Menu and Clearing the Call (Refer to step 2 of Fig.4-3.)

Select the scene file number called at the “SCENE FILE” page of the PAINT menu. A file currently being

called is shown with its file No. highlighted. Selecting the number again clears the call and resets the state

before calling.

Storing with MSU (Refer to step 1 of Fig.4-3.)

(1) Change the scene file item to the desired value.

(2) Press “STORE” of the scene file, and press the STORE number.

Calling with MSU and Clearing the Call (Refer to step 2 of Fig.4-3.)

Press the No. switch of the “SCENE FILE” to call. The switch also lights up. Press again to cancel the

call and turn off the switch.

HDC-900/950 IMM

4-4 (E)

4-4. Registering the Scene File

Storing the Scene File to the Memory Stick (Refer to step 1 of Fig. 4-3.)

The scene file stored in the camera unit is stored to the memory stick.

Set the setup menu as follows.

Reading the Scene File from the Memory Stick (Refer to step 3 of Fig. 4-3.)

The scene files stored in the memory stick are read to the memory of camera unit.

Set the setup menu as follows.

When the power is just turned on, the reference files stored in the memory stick will not be read. This file

will only be read when READ is executed at the setup menu.

Camera unit

Storing in

Storing

(Step 1)

memory stick

(Step 1)

Scene File

Memory stick

Current paint data

Output to hardware

Readng from

memory stick

(Step 3)

Calling

(Step 2)

Fig. 4-3. Operating Procedure for Scene Files

HDC-900/950 IMM

4-5 (E)

4-5. Registering Reference Files

This file can be stored and read using the setup menu or MSU (master setup unit). Only one file can be

stored, and will be stored in the camera and memory stick.

As for the items to be stored, refer to Section 4-8,“ File Items”.

For reference files, differential data taking the factory-setting as 0 will be stored. Therefore, initializing

the reference file brings the settings to the same status at factory-setting.^(*1)Using the setting menu, all

items or specified items can be initialized.

Reference files can be copied between cameras using the memory stick.

(*1) : If lens files or OHB file retains the data, those need to be initialized as well.

. As for the setup menu, refer to Section 3.

. Before storing the file in the memory stick, make sure that the LOCK switch on the memory stick is in

OFF position.

Storing Using the Setup Menu (Refer to step 1 of Fig.4-4.)

Set the setup menu as follows.

[FILE] → [REFERENCE] → [STORE|FILE]

The data will be stored in the camera and the numerical data will be displayed as 0. (Excluding some

items. Refer to Section 4-8. “File Items”.)

Storing by MSU (Refer to step 1 of Fig.4-4.)

Set the MODE switch to FILE and press [REFERENCE] and then press [REF|STORE]. The data will

be stored in the camera and the numerical data will be displayed as 0. (Excluding some items. Refer to

Section 4-8. “File Items”.)

Calling Using the Setup Menu (Refer to step 2 of Fig. 4-4, Fig. 4-1.)

Set the setup menu as follows.

[PAINT] → [SCENE|FILE] → [STANDARD]

The temporary paint amount and scene file amount will be cleared and the reference file will be reset to

the state stored in.

Calling with MSU (Refer to step 2 of Fig. 4-4.)

Press the “STANDARD” switch to reset the reference file item to the state stored in.

HDC-900/950 IMM

4-6 (E)

4-5. Registering Reference Files

Reading the Reference File from the Memory Stick (Refer to step 3 of Fig. 4-4.)

During the file storing, the reference files which have been stored in the memory stick at the same time

are read and the reference files in the camera can also be changed.

Set the setup menu as follows.

After the data of the memory stick is read to the camera, STANDARD will be executed automatically.

When the power is just turned on, the reference files stored in the memory stick will not be read. This file

will only be read when READ is executed at the setup menu.

Storing the Reference File to the Memory Stick (Refer to step 1 of Fig. 4-4.)

The reference file stored to the camera unit is stored in the memory stick.

Set the setup menu as follows.

Initializing All File Items Using the Setup Menu (Refer to step 4 of Fig. 4-4.)

Set the setup menu as follows.

HDC-900/950 IMM

4-7 (E)

4-5. Registering Reference Files

Initializing Only Specified Items Using the Setup Menu (Refer to step 4 of Fig. 4-4.)

References files for specified items can be initialized using the setup menu.

(1) Set the setup menu as follows.

[FILE] → [FILE|CLEAR] → [10|SEC|CLEAR] → [ON]

(2) Move to the page containing the items to be initialized from the reference files in the setup menu.

(3) HDC-900/910

Adjust “→” to the item to be initialized using the MENU SELECT control, and keep pressing the

MENU SELECT switch toward the ENTER side about 10 seconds at “?” state until “REF CLEAR “

is displayed. About 3 seconds later, “DATA CLEAR” will be displayed at the bottom most line. The

“REF CLEAR” is displayed about 10 seconds later, and the data will be initialized to 0.

HDC-950/930

Adjust “→” to the item to be initialized using the rotary encoder, and keep pressing the rotary

encoder about 10 seconds at “?” state until “REF CLEAR “ is displayed. About 3 seconds later,

“DATA CLEAR” will be displayed at the bottom most line. The “REF CLEAR” is displayed about

10 seconds later, and the data will be initialized to 0.

The 10 SEC CLEAR function must always be set to OFF when the power is turned ON.

Memory stick

Storing in

memory stick

(Step 1)

Readng from

memory stick

(Step 3)

Camera unit

Storing

Initialization

(Step 4)

(Step 1)

Reference File

factory-set value

(Initial value 0)

Reference File

Current paint data

Output to hardware

Calling

(Step 2)

Fig. 4-4. Operating Procedure for Reference Files

HDC-900/950 IMM

4-8 (E)

4-6. Registering the Lens File

The white shading which occurs when the extender is turned on, flare balance, white balance, F value of

the open edge of the lens, name, etc. can be stored. Up to 16 files can be stored. The adjustment data can

be called by selecting the lens file. This data will be stored in the camera.

As for the items to be stored, refer to Section 4-8,“ File Items”.

The lens file stores the differential data from the reference file.

. Prior to creating the lens file, perform the necessary adjustments by using the lens normally used to

create the reference file.

. As for the setup menu, refer to Section 3.

Adjusting the Lens File

(1) Mount the lens. Select the file with the same name of the lens mounted from the setup menu.

If no file with the same lens name, select “NO OFFSET”.

[FILE] → [LENS|FILE] → [No.] → (Select the No.)

(2) Set the lens file name and F value of the open edge of the lens.

(3) With the lens extender set to OFF, adjust V modulation of R/G/B/Master. Shoot the all white pattern,

set the iris F4 and zoom position to the center of the ring, and perform the adjustment around 560 mV

of 80% video level. Also adjust the flare balance and white balance shooting the grayscale chart.

(4) Store the data in the lens file. Set the setting menus as follows.

[FILE] → [LENS|FILE] → [STORE|FILE]

(5) Set the extender to ON, adjust the V modulation of R/G/B/Master shooting the all white pattern, and

adjust the flare balance and white balance shooting the grayscale chart.

(6) Store the data in the lens file.

(7) If the lens center deviates when the lens extender is switched to ON/OFF, store the center marker

under the extender is ON state. Adjust [CENTER|H|POS] and [CENTER|V|POS] at the

[LENS|FILE] page, and execute [STORE|CENTER].

The center marker will not be stored when the lens file is stored.

Calling the Lens File

Select the lens file set by the setup menu as follows.

[OPERATION] → [LENS|FILE]

Initializing the Lens File

Set the setup menu as follows.

All data of the lens file being currently selected will be initialized to the factory setting values.

HDC-900/950 IMM

4-9 (E)

4-7. Registering the OHB File

The OHB file is used for storing the maintenance adjustment values of the CCD block and the data will

be stored in the camera. The data can be stored using the setup menu or the MSU (master setup unit).

The items to be stored are the black shading, white shading, ND offset and OHB matrix.

As for the setup menu, refer to Section 3.

4-7-1. Storing the Black Shading and White Shading

Storing Using the Setup Menu

(1) Execute the setup menu as follows.

[FILE] → [REFERENCE] → [STANDARD]

(2) Change the items to the desired value; H SAW, H PARA, V SAW and V PARA of each R/G/B for

each of white shading and black shading.

(3) Set the setup menu as follows.

[FILE] → [OHB|FILE] → [STORE|FILE]

Storing with MSU

(1) Change the items to the desired value; H SAW, H PARA, V SAW, V PARA of each R/G/B for each

of white shading and black shading.

(2) Press “STORE” of the OHB file.

HDC-900/950 IMM

4-10 (E)

4-7. Registering the OHB File

4-7-2. Adjusting the ND Offset

The white balance may be slightly deviated in the ND filters. In such cases, adjust the offset. Taking the

ND filter 1 white balance as the reference, the ND offset stores the deviation of the white balance of ND

filter 2, 3, 4.

Adjusting the ND Offset

(1) Set the setup menu as follows.

[FILE] → [REFERENCE] → [STANDARD]

(2) Connect the waveform monitor to MONITOR OUT connector of this unit.

(3) Select ND filter 4, and shoot the grayscale chart. Check that the illuminant condition is under that

video level is within 560 mV thru. 630 mV. Then note the video level at this time.

Do not adjust the ND offset if the video level is less than 560 mV.

(4) Select 1 by the ND filter knob, and set the iris so that the video level is the same level as the noted

video level of Step (2).

(5) Execute the auto white balance.

(6) Select 2 by the ND filter knob, and set the iris to meet the noted video level of Step (2).

(7) Execute the auto white balance.

(8) Select 3 by the ND filter knob, and set the iris to meet the noted video level of Step (2).

(9) Execute the auto white balance.

(10) Select 4 by the ND filter knob, and set the iris to meet the noted video level of Step (2).

(11) Execute the auto white balance.

(12) Store the ND offset.

Execute the setup menu as follows.

[FILE] → [OHB] → [STORE|FILE]

. Adjust precisely to meet the noted video level, otherwise the deviation of the white balance of the ND

filter may generate in some cases.

. If the level cannot be adjusted properly using the iris, adjust the level using the shutter/ECS or gain-up.

Calling the ND Offset

When the ND filter is changed, the ND offset will be called automatically.

Initializing the ND Offset

Execute the setup menu as follows.

[FILE] → [FILE|CLEAR] → [OHB|ND|OFFSET]

HDC-900/950 IMM

4-11 (E)

4-8. File items

OPERATION menu

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

turned ON set

Factory

VF DISPLAY

! IND

(*2)

MARKER

(*2)

GAIN SW L/M/H

ZEBRA

0/6/12 dB

(*2)

VF DETAIL

AUTO IRIS WINDOW

OVERRIDE

BATT ALARM

D5600K

1 ^(*8)

(*2)

REF

OFF

_60 dB

RET2

LEFT

ASSIGNABLE 1/2

MIC 1 GAIN

MIC 2 GAIN

LENS VTR S/S

CAM VTR S/S

ZOOM DISP

LENS FILE NO.

PAINT menu

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

(*4)

WHITE R/B

REF ^(*7)

REF

WHITE G

BLACK R/G/B

BLACK MASTER

FLARE R/G/B

REF

FLARE SW

V MOD R/G/B

V MOD MASTER

V MOD SW

GAMMA R/G/B

GAMMA MASTER

GAMMA COARSE

GAMMA TABLE

GAMMA SW

REF

0.45

STANDARD4

BLK GAMMA R/G/B

BLK GAMMA MASTER

BLK GAMMA RGB RANGE

BLK GAMMA RGB SW

BLK GAMMA Y

REF

OFF

HDC-900/950 IMM

4-12 (E)

4-8. File items

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

BLK GAMMA Y RANGE

REF

OFF

BLK GAMMA Y SW

LOW KEY SAT

OFF

LOW KEY SAT SW

SATURATION SW

SATURATION LEVEL

LOW KEY SAT RANGE

KNEE POINT R/G/B

KNEE POINT MASTER

KNEE SLOPE R/G/B

KNEE SLOPE MASTER

KNEE SW

OFF

LOW

AUTO KNEE SW

OFF

ADAP KNEE SW

OFF

WHITE CLIP R/G/B

WHITE CLIP MASTER

WHITE CLIP SW

KNEE SAT LEVEL

KNEE SAT SW

OFF

DETAIL LEVEL

DETAIL SW

DETAIL WHITE LIMITER

DETAIL BLACK LIMITER

DETAIL LIMITER MASTER

DETAIL CRISPEN

DETAIL H/V RATIO

DETAIL H FREQ

DETAIL LEVEL DEPEND

DETAIL LEVEL DEP SW

KNEE APERTURE

KNEE APT SW

OFF

SKIN DETAIL LEVEL

SKIN DETAIL PHASE 1/2/3

SKIN DETAIL WIDTH 1/2/3

SKIN DETAIL SAT 1/2/3

SKIN DETAIL CH_1 SW

30d

_89

SKIN DETAIL CH_2,3 SW _

SKIN DETAIL GATE SW

SKIN DETAIL GATE 1 SW _

REF

OFF

ON ^(*1)

OFF ^(*1)

SKIN DETAIL GATE 2/3 SW

USER MATRIX

OFF

REF

OFF

USER MATRIX SW

PRESET MATRIX SEL

OFF

SMPTE-240M

HDC-900/950 IMM

4-13 (E)

4-8. File items

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

turned ON set

Factory

PRESET MATRIX SW

REF

OFF

MATRIX SW

MULTI MATRIX PHASE

MULTI MATRIX HUE

MULTI MATRIX SAT

MULTI MATRIX SW

SHUTTER SEL

SHUTTER SW

ECS SW

REF

OFF

1/100

OFF

30.0 Hz

(*5)

REF

ECS FREQ

S_EVS (%)

S_EVS SW

OFF

TEST 1

TEST 2

MAINTENANCE menu

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

WHITE SHADING

VSAW R/G/B

OHB

WHITE SHADING

VPARA R/G/B

WHITE SHADING

HSAW R/G/B

WHITE SHADING

HPARA R/G/B

BLACK SHADING

VSAW R/G/B

BLACK SHADING

VPARA R/G/B

BLACK SHADING

HSAW R/G/B

BLACK SHADING

HPARA R/G/B

BLACK SET R/G/B

MASTER GAIN

(*5)

REF

0 dB

OHB MULTI MATRIX PHASE

OHB MULTI MATRIX HUE

OHB MULTI MATRIX SAT

OHB MATRIX SW

AUTO IRIS SW

OHB

OFF

ON^(*3)

AUTO IRIS LEVEL

AUTO IRIS APL RATIO

AUTO IRIS GAIN

REF

IRIS CLOSE SW

OFF ^(*3)

OFF

CAMERA ID

HDC-900/950 IMM

4-14 (E)

4-8. File items

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

MULTI FORMAT

59.94 I

OFF

PROMPTOR

BNC SDI OUT

LINER EXP

OFF

VTR 26P CABLE COMP

VTR 26P MAIN VIDEO ADJ

VTR 26P VIDEO SEL

BATT ALARM

OFF

YPbPr

(*2)

FAN MODE

REF

AUTO1

H PHASE

CHU BARS

OFF

MENU RESUME

DATE TYPE

OPE MENU

Y/Mn/D

WHITE MEMORY

COLOR BAR

FULL 16 : 9

CONTROL

(1CH)

EXT F NO

TRUNK LINE

VSAW OFST R/G/B^(*10)

(*11)

10 m : _8

25 m : _16

50 m : _32

TEST 1

TEST 2

OFF

FILE menu

page item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

4^a)

LENS FILE NAME

LENS FILE IRIS F NO.

F2.0

LENS FILE CENTER

MARKER H

LENS FILE CENTER

MARKER V

6^a)

REFERENCE 10 SEC

CLEAR

OFF

a) These pages are different by the ROM version on the AT board of the unit.

External switches

item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

Factory

turned ON set

ND FILTER

ND OFFSET

CC FILTER

ND1

CCB

(*5)

AUTO KNEE (DCC)

CHU COLOR BAR

REF

OFF

(*5)

(*6)

WHITE MEMORY PRESET A, B _

HDC-900/950 IMM

4-15 (E)

4-8. File items

MSU connected only

item

OPERATOR REFERENCE SCENE

OHB

LENS

STANDARD ^(*9)Power is

turned ON set

Factory

V DTL CREATION MODE

V DTL CONTROL MODE

KNEE MAX

REF

OFF

REF

H/V

OFF

AUTO KNEE POINT

WHITE SETUP MODE

AWB

shows an analog item which will not be indicated as 0 after being stored.

O shows an analog item which will be indicated as 0 after being stored.

shows a switch which will be stored in the select item.

REF returns the status to the one when stored in the reference file.

OHB returns the status to the one when stored in the OHB file.

If mentioned as ON or OFF, the values will be same as ON or OFF.

If mentioned as _, the value does not change.

(*1): In SKIN DETAIL GATE 1/2/3, one among 1, 2 and 3 is to be set ON.

(*2): Refer to Section 4,“ Setup Menu”.

(*3): Only when using standalone

(*4): WHITE value stored is used when the extender ON.

(*5): The state depends on the one of the external switch when the standalone state.

(*6): When connecting to the MSU (master setup unit), the memory enters the temporally released state. As PRESET

brings WHITE R/G/B to 0, regardless of the factory setting value of 3200K, if changing WHITE R/G/B and per-

forming REFERENCE STORE, the specified value is recalled as PRESET.

(*7): When WHITE SETUP MODE setting is ABW, the value when selecting AWB is returned and when selecting

AUTO LEVEL, 0 is returned.

(*8):

Setting

screen

indicates the auto iris window frame.

(*9): Shows items to be called when [STANDARD] is executed, that is the reference file is called.

(*10): These items can be set only when HKC-T950 is connected.

(*11): Saved in the cable adaptor of HKC-T950.

HDC-900/950 IMM

4-16 (E)

The material contained in this manual consists of

information that is the property of Sony Corporation.

Sony Corporation expressly prohibits the duplication of

any portion of this manual or the use thereof for any

purpose other than the operation or maintenance of the

equipment described in this manual without the express

written permission of Sony Corporation.

Le matériel contenu dans ce manuel consiste en

informations qui sont la propriété de Sony Corporation.

Sony Corporation interdit formellement la copie de

quelque partie que ce soit de ce manuel ou son emploi

pour tout autre but que des opérations ou entretiens de

l’équipement à moins d’une permission écrite de Sony

Corporation.

Das in dieser Anleitung enthaltene Material besteht aus

Informationen, die Eigentum der Sony Corporation sind.

Die Sony Corporation untersagt ausdrücklich die

Vervielfältigung jeglicher Teile dieser Anleitung oder den

Gebrauch derselben für irgendeinen anderen Zweck als

die Bedienung oder Wartung der in dieser Anleitung

beschriebenen

Ausrüstung

ohne

ausdrückliche

schriftliche Erlaubnis der Sony Corporation.

HDC-900/950 IMM

HKC-T950 (SY)

HDC-900 (SY)

HDC-900/L (J)

HDC-910 (UCJ, CE)

HDC-910/L (J)

HDC-930 (SY)

Printed in Japan

2003. 10 08

HDC-950 (JN, SY) J, E

3-204-338-08

Sony Corporation

B&P Company

Vulcan Hart GHCB44 User Manual
Vivitar DVR650 User Manual
Sony XCI SX1 User Manual
Sony WM SP1 User Manual
Sony WM FX521 User Manual
Sony MV 100BAT User Manual
Sony Handycam DCR DVD101E User Manual
Sony DCR DVD300 User Manual
Sony CDC X417 User Manual
Sharp AQUOS BD HP24U(A) User Manual