OPERATING INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
CDC-X517M
YU
CDC-X417
YU
CDC-X317
YU
STEREO CAR CD RECEIVER
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA
AUTOMOVIL
ENGLISH
ESPAÑOL
FRANÇAIS
OWNER’S RECORD
For your convenience, record the model number and
serial number (you will find them on the bottom side of
your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of
difficulty.
Model No. CDC-X517M, CDC-X417, CDC-X317
Serial No.
THEFT PROTECTION
BASIC OPERATION,
AUDIO AND CLOCK
ADJUSTMENT
Take the front panel with you when leaving the car, and
keep it in the supplied carrying case.
Detaching the front panel
Before detaching the front panel, remove the CD to
prevent possible damage to the unit.
1
2
3
Press z to remove the CD.
Press and hold PWR/MUTE until the unit turns off.
Press %. (Hold the panel with one hand to prevent
accidentally dropping it.)
4
Remove the panel.
Smart Jog
Turning the unit on/off
• Press PWR/MUTE to turn on the unit. The unit also
turns on when you insert a CD.
• Press and hold PWR/MUTE until the unit turns off.
Note
Most operations described in this manual require the
unittobeturnedonbeforestartingtheoperation, unless
explicitly stated otherwise.
Attaching the front panel
1
2
Engagetheleftsideofthefrontpaneltotheleftcatch
on the unit.
Changing the source mode
Push the panel forward until it locks. Be sure not to
press any buttons while you are attaching the panel.
1
Press FNC.
Pressing FNC cycles through source modes in the
following order:
* “CD” does not appear in the display when there is no
CD in the unit.
**CD Changer Play mode (CDC-X517M only, available
when an optional CD Changer is connected)
Adjusting the volume
Note
Donottouchthefrontpanelconnector.Thiscouldcause
a poor or faulty connection.
1
Turn the Smart Jog.
VOL (volume) indicator flashes.
Security lamp
Muting the sound
The security lamp will continue to flash while the front
panel is detached from the unit.
1
Press PWR/MUTE briefly.
To restore volume, briefly press PWR/MUTE again.
ENGLISH 2
Adjusting sound
Setting the clock
You can select the following modes for adjusting sound
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/ rear) and H-BASS (high bass)
1
2
3
Press and holdDISP until the clock indicator flashes
in the display.
Press TUNEi (to set hour) or TUNEk (to set
minute) and turn the Smart Jog.
Press DISP.
1
Press SEL repeatedly to select the mode to be
adjusted.
Pressing SEL cycles through the modes. The
selected mode’s indicator flashes.
TurntheSmartJogtoincreaseordecreasethelevel
for the selected mode (except for H-BASS).
In H-BASS mode, turn the Smart Jog to select on or
off.
Displaying the clock
1
Press DISP.
2
To return to the former display, press DISP again.
RADIO OPERATION
Note
Adjust the level or select on/off within 5 seconds, or the
selected mode will return to previous state.
Tuning in to a station
(Seek/Manual Tuning)
Aligning the source levels
(Source Level Adjuster)
Volume may vary each time you change the source
mode. In this case, you can align each source mode’s
volume to almost the same level.
1
2
PressFNCrepeatedlytoselectthedesiredmode.
Press DISP while pressing SEL.
“LA 0” appears in the display.
Stereo indicator Local indicator
3
Turn the Smart Jog to adjust the level.
Note
Adjust the level within 5 seconds, or the selected mode
will be canceled.
Band indicator Frequency indication
Restoring the factory settings
1
Press FNC repeatedly to select the desired band
(FM1, FM2, FM3, AM1 or AM2).
1
2
Turn off the unit.
Press and hold DISP until “LA --” appears in the
display.
2* Press TUNEi (to move to higher frequencies) or
TUNEk (to move to lower frequencies) to tune in to
a station.
Note
“ST” appears in the display when a station is
broadcasting in stereo, and receiving conditions are
good.
YoucanrestorethefactorysettingsonlyforVOL,BASS,
TRE, BAL, FAD, and H-BASS, and aligned source
volume levels.
*Seek Tuning and Manual Tuning
• Press and hold TUNEi or TUNEk until seek Tuning
starts.
Muting button beep sounds
The unit locates a station automatically (Seek Tuning).
• Press TUNEi or TUNEk repeatedly to search for a
desired station while increasing or decreasing the
frequency step by step (Manual Tuning).
To stop Seek Tuning, press TUNEi or TUNEk
again.
1
2
Turn off the unit.
Press and hold SEL until “bEEP” appears in the
display.
3
4
Turn the Smart Jog to select on (level indicators
appear) or off (level indicators disappear).
Press and hold SEL until the unit turns off.
Monaural mode
When signals become weak, or reception becomes
poor, the unit automatically switches to Monaural mode
to reduce noise.
3 ENGLISH
Local mode
Presetting stations manually
(Manual Memory)
Local mode allows you to tune in only to strong stations
during Seek Tuning.
1
2
3
Press FNC repeatedly to select the desired band
(FM1, FM2, FM3, AM1 or AM2).
Press TUNEi or TUNEk to tune in to a desired
station (see “Tuning in to a station,” page 3).
Press the desired preset station button until the unit
beeps.
1
Press LO before you start seek tuning.
“LO” appears in the display.
To return to Distant mode, press LO again.
“LO” disappears and the unit tunes in to all receivable
stations.
Using preset stations
Note
A newly preset station replaces the station on the same
band that was previously stored on that preset station
button.
Youmustpresetstationsbeforeyoucantuneinastation
using preset station number buttons.
Tuning in to a preset station
1
2
Press FNC repeatedly to select the desired band
(FM1, FM2, FM3, AM1 or AM2).
Press the preset station button on which the desired
station is stored.
Preset station buttons 1 ~ 6
Active tuning reception control (ATRC)
The unit automatically suppresses FM noise caused by
vehicle movement, and maintains sound quality.
Using the timer
(My Information)
Preset station
number
You can schedule the radio to activate for daily radio
programs. The unit automatically turns on and off in
Radio mode at the scheduled times.
Presetting stations automatically
(Auto Memory)
1
Press FNC repeatedly to select the desired band
(FM1, FM2, FM3, AM1 or AM2).
Press and hold PS/A.ME until automatic presetting
starts.
2
The unit automatically stores up to 6 stations for
each band.
After completion of automatic presetting, the unit
tunes in to the station stored on preset station
button 1.
MY INFO indicator
Smart Jog
Tocancelautomaticpresetting,pressPS/A.MEagain.
Setting the timer
Checking the preset stations (Preset Scan)
1
2
Turn off the unit.
Press and hold INFO until “PO” flashes in the
display.
Press SEL.
1
Press PS/A.ME briefly.
Each preset station will be tuned in for 5 seconds in
order.
To cancel Preset Scan, press PS/A.ME again or any
3
4
Set the time you wish the unit to turn on.
preset station button.
• Press TUNEi and turn the Smart Jog to set the hour.
• Press TUNEk and turn the Smart Jog to set the
minute.
5
6
7
Press SEL.
Press FNC to select the band.
PressTUNEi,TUNEkorthedesiredpresetstation
button to select the station.
8
9
Press SEL.
Set the time you wish the unit to turn off following the
same procedure used in step 4.
ENGLISH 4
Labeled-side up
10 Press and hold INFO until the unit turns off, and
setting is completed.
When the unit is on, “MY INFO” appears in the
display indicating that the unit is standby for a timer.
During the timer-activated tuning, “MY INFO”
continues to flash.
To cancel the timer standby, press INFO so that
“MY INFO” disappears.
CD indicator
Track number
Note
• To discontinue the timer setting, press and hold PWR/
MUTE until the unit turns off.
• To check the setting, turn off the unit, then pressINFO.
The unit displays the scheduled turn-on and turn-off
times with the appropriate radio frequency.
• The unit automatically starts tuning at the scheduled
time regardless of the current source mode. When the
scheduled program is over, the unit automatically
returns to the former source mode.
• Timer setting remains enabled even if you turn off the
unit, and then turn it on. This is true even if you detach
the front panel, and reattach it.
Elapsed playing time
To
Press
z
Eject a CD
Skip to the next track
t
r
Go back to the beginning
of the current track
Each extra press skips
backward one extra track
• However, ifyoupressFNCtochangethesourcemode
during timer-activated tuning, the scheduled program
is canceled.
Locate a specific point in Press and hold r or
a track
t until you find the
point.
Note
CD PLAYER OPERATION
• When you play a CD that is already inserted, CD play
starts at the point where it stopped the previous time.
A newly inserted CD starts from the first track.
• A CD-R or CD-RW may take some time to start playing
back, but this is not a malfunction.
Playing a CD
You can play CDs, CD-Rs and CD-RWs using the
procedure described below.
• If a CD-R or CD-RW with no data or incompatible data
is inserted, “E03” will appear in the display. The unit
cannot play such discs.
Intro Play
You can locate a desired track by monitoring the first 10
seconds of all the tracks on a CD.
1
Press INT during CD play.
“SCAN” appears in the display.
2
Press INT again when the desired track is played.
The unit returns to normal CD play.
1
Insert a CD.
“CD” appears in the display.
CD play starts.
If a CD is already inserted, press FNC repeatedly to
select CD play mode.
One track Repeat Play
You can play a track repeatedly.
1
Press REP1 during CD play.
“REPEAT1” appears in the display.
To cancel One track Repeat Play, press REP1 again.
In normal play, when the last track finishes, the unit
returns to the first track and continues to play.
Random Play
You can play all the tracks in random order.
1
Press RNDM during CD play.
“RANDOM” appears in the display.
To cancel Random Play, press RNDM again.
Note
During Random Play, pressing r allows you to skip
only to the beginning of the current track, not to the
previous track.
5 ENGLISH
AUXILIARY EQUIPMENT
STEERING WHEEL
REMOTE CONTROL
(CDC-X517M and CDC-X417)
Listening to a cassette/MD/MP3 portable
player or other equipment
Youcanlistentoequipmentconnectedtotheunit. Refer
to the operating instructions for the corresponding
equipment for more detailed information.
Remote control button
Be sure to remove inserted CDs to prevent possible
damage to the unit before connecting the equipment.
1 VOLUME + button: To increase the volume.
2 VOLUME - button: To decrease the volume.
3 FUNCTION button: To select Radio, CD Play, CD
Changer Play (CDC-X517M only) or AUX IN mode.
AUX IN jack
1
2
Connectacassette/MD/MP3portableplayerorother
equipment via the unit’s AUX IN jack (3.5 mm).
Press FNC repeatedly until “AUX” appears in the
display.
4 DISC/PRESET
button:
(CD) To skip back to the beginning of the current
track. Each extra press skips backward one extra
track.
During AUX mode, the clock display appears.
(Radio) To tune in to the next preset station, in
descending order.
(CD Changer: CDC-X517M only)
Press and release to skip back to the beginning of
the current track or the previous track.
Press and hold to switch to the previous CD.
5 DISC/PRESET button:
OTHER FUNCTIONS
(CD) To skip to the next track.
(Radio) To tune in to the next preset station, in
ascending order.
(CD Changer: CDC-X517M only)
Smart Jog
Press and release to skip to the next track.
Press and hold to switch to the next CD.
Changing the key illumination color
(CDC-X517M and CDC-X417)
CD CHANGER
OPERATION
(CDC-X517M only)
Youcanchooseblueorredasthekeyilluminationcolor.
1
Press and hold FNC until “ILL” appears in the
display.
2
TurntheSmartJogtoselect1(forblue)or2(forred).
Playing a CD
YoucanplayCDsfromaconnectedAIWACDChanger.
For detailed information on installing a CD Changer,
refertotheInstallationandConnectionmanualsupplied
with the CD Changer.
ENGLISH 6
CD Changer indicator
Track number
TROUBLESHOOTING
Error code
In the following cases the corresponding error code
indication appears. Follow the suggestions below to
solve such problems. If the error code indication does
not disappear, consult an AIWA service center.
CD number
Press FNC repeatedly to display “CD-CH.”
E01* The disc magazine is not properly inserted in the
CD Changer. Reinsert the magazine. Refer to
the instruction manual for the CD Changer.
E02* No CDs are loaded in the disc magazine. Insert
CDsproperly. Refertotheinstructionmanualfor
the CD Changer.
E03 Focuserror.CheckthattheCDisloadedproperly
(right side up, etc.), and the CD contains valid
data.
E04* Problem with the CD Changer. Reset the unit by
pressing the Reset button. If this does not solve
the problem, consult an AIWA service center.
* CDC-X517M only
1
The CD Changer play starts.
To
Press
Skip to the next track
t
Skip back to the beginning of
the current track or to the
previous track
r
Advance rapidly to locate a
desired point
and hold t, then
release it at the
desired point
Reverse rapidly to locate a
desired point
and hold r, then
release it at the
desired point
Reset button
Start CD Changer play from DISCN
the first track on the next disc
IfaCDdoesnotoperateproperly, presstheresetbutton
with a pointed object such as a pencil, etc. Note that all
your settings will be erased if this button is pressed.
Start CD Changer play from DISCM
the first track on the previous
disc
Intro Play
You can locate a desired track by monitoring the first 10
secondsofallthetracksontheCDsinthediscmagazine.
1
Press INT during CD Changer play.
“SCAN” appears in the display.
Reset button
2
Press INT again when the desired track is played.
The unit returns to normal CD play.
One track Repeat Play
You can play a track repeatedly.
MAINTENANCE
1
Press REP1 during CD Changer play.
“REPEAT1” appears in the display.
To cancel Repeat Play, press REP1 again.
Cleaning the front panel
Wipe the surface with a soft, dry cloth.
One disc Repeat Play
You can play all tracks on a disc repeatedly.
Cleaning the connector
1
Press REP during CD Changer play.
The connector needs to be cleaned occasionally. Wipe
the surface of the connector with a cotton swab slightly
moistened with alcohol.
“REPEAT” appears in the display.
To cancel Repeat Play, press REP again.
Random Play
You can play all the tracks on the CDs in the disc
magazine in random order.
Back of the front panel
1
Press RNDM during CD Changer play.
“RANDOM” appears in the display.
To cancel Random Play, press RNDM again.
Note
PressingrduringRandomPlaylocatesthebeginning
of the current track. The unit does not retrieve previous
tracks during Random Play.
7 ENGLISH
STEERING WHEEL REMOTE CONTROL
SPECIFICATIONS
RADIO SECTION
(CDC-X517M and CDC-X417)
Dimensions: approx. 67 (W) × 26 (H) × 27 (D) mm
(2 3/4 (W) × 1 1/16 (H) × 1 1/8 (D) inches) (excluding
holder)
Weight: approx. 38 g (1.33 oz.) (including holder,
battery)
(FM)
Frequency Range: 87.5 MHz – 108 MHz (100-kHz
steps)* or 87.5 MHz – 108 MHz (50-kHz steps)*
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 80 dB
Supplied Accessories: Mounting kit (1 set), Lithium
battery (1)
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 63 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 70 dB
Capture Ratio: 3 dB
• Specifications and external appearance are subject to
change without notice due to product improvement.
REAR PANEL
(AM)
CDC-X517M
Frequency Range: 530 kHz – 1,710 kHz (10-kHz
steps)* or 531 kHz – 1,602 kHz (9-kHz steps)*
Usable Sensitivity: 30 µV (30 dB)
* Set the frequency increment for your area using
the switch on the bottom of the unit. (The switch
is factory-set to the 10k position [for the U.S.A.])
CDC-X417, CDC-X317
CD SECTION
Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 80 dB
Channel Separation: More than 65 dB
S/N Ratio: More than 85 dB
Wow/Flutter: Not applicable
AUDIO SECTION
Max. Power Output: 50 W × 4 channels
(CDC-X517M), 45 W × 4 channels (CDC-X417,
CDC-X317)
AUX IN input
Input sensitivity (load impedance) AUX IN: 300 mV
(10 kΩ)
GENERAL
Power-Supply Voltage: 14.4 V (11 to 16 V
allowable), DC, negative ground
Load Impedance: 4 Ω
Tone Control:
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz
Preamp Output Voltage (load impedance): 2.2 V
(10 kΩ)
Installed size: 182 (W) × 53 (H) × 155 (D) mm
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)
Supplied Accessory: Carrying case (1)
ENGLISH 8
8B-KCF-901-01
000914ATM-OX
Printed in Indonesia
|