A-E99-100-11 (1)
HD Color Video Camera
Command List
Version 1.00
BRC-H900
© 2012 Sony Corporation
Note
1)
VISCA RS-232C/RS-
In the same network, all the camera address selectors
should be set to “0” (automatic setting) or all the
selectors should be manually set to “1” to “7”. Do not
mix the automatic and manual settings.
422 Commands
Use of RS-232C/RS-422 control software based upon
this command list may cause malfunction or damage to
hardware and software. Sony Corporation is not liable
for any such damage.
Each VISCA equipment has VISCA IN and VISCA
OUT connectors.
Set the DTR input (the S output of the controller) of
VISCA IN to H when controlling VISCA equipment
from the controller.
Overview of VISCA
Fig. 1 VISCA network configuration
In VISCA, the side outputting commands, for example,
a computer, is called the controller, while the side
receiving the commands, such as a BRC-H900, is called
the peripheral device. The BRC-H900 serves as a
peripheral device in VISCA. In VISCA, up to seven
peripheral devices like the BRC-H900 can be connected
to one controller using communication conforming to
the RS-232C/RS-422 standard. The parameters of RS-
232C/RS-422 are as follows.
VISCA Controller
VISCA Equipment
IN
OUT
• Communication speed: 9600 bps/38400 bps
• Data bits : 8
• Start bit : 1
IN
• Stop bit : 1
• Non parity
Flow control using XON/XOFF and RTS/CTS, etc., is
not supported.
OUT
Peripheral devices are connected in a daisy chain. As
shown in Fig. 1, the actual internal connection is a one-
direction ring, so that messages return to the controller
via the peripheral devices. The devices on the network
are assigned addresses.
IN
The address of the controller is fixed at 0.
OUT
The addresses of peripheral devices are as follows.
When the camera address selector is set to 0
(automatic setting mode)
The peripheral devices are assigned to the addresses, 1,
2, 3… in the connected order, starting from the one
connected nearest to the controller. These addresses are
set when the controller sends address commands during
initialization of the network.
When the camera address selector is set to 1
through 7 (manual setting mode)
The addresses of the peripheral devices will be set to the
pre-selected numbers. Within a single system, the same
number can be used only once. If an address selector
number other than 0 is used, set the camera address
selectors on the connected BRC-H900 cameras to
different numbers.
............................................................................................................................................................................................................................
1) VISCA is a protocol developed by Sony for controlling a consumer’s camcorder. “VISCA” is a trademark of Sony Corporation.
3
BRC-H900 assigned address 2 is 82H. In the command
list, as the header is 8X, input the address of the BRC-
H900 to X. The header of the reply packet from the
BRC-H900 assigned address 1 is 90H. The packet from
the BRC-H900 assigned address 2 is A0H.
Some of the setting commands for BRC-H900 can be
sent to all devices at one time (broadcast). In the case of
broadcast, the header should be 88H in hexadecimal.
When the terminator is FFH, it signifies the end of the
packet.
VISCA Communication
Specifications
VISCA packet structure
The basic unit of VISCA communication is called a
packet (Fig. 2). The first byte of the packet is called the
header and comprises the sender’s and receiver’s
addresses. For example, the header of the packet sent to
the BRC-H900 assigned address 1 from the controller
(address 0) is 81H in hexadecimal. The packet sent to the
Packet (3 to 16 bytes)
Message (1 to 14 bytes)
Header
Terminator
Byte 1
Byte 2
Byte 3
FF
Sender’s
address
Receiver’s address
1
0
1
1
1
1
1
1
1
1
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(MSB) (LSB)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(MSB)
(LSB)
Fig. 2 Packet structure
Note
Fig. 2 shows the packet structure, while Fig. 3 shows the
actual waveform. Data flow will take place with the LSB
first.
1 byte
Start
bit
Stop
bit.
Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7
(LSB) (MSB)
Fig. 3 Actual waveform for 1 byte.
Timing Chart
General commands
As VISCA command processing can only be carried out
a maximum of one time in a Vertical (V*) cycle, it takes
maximum 4V-cycle time for an ACK/Completion to be
returned.
If the Command and ACK/Completion communication
time is shorter than 1V-cycle time, a command can be
received at every 1V cycle. From this point, if two or
more commands are to be sent successively, wait for a
reply command (an ACK or error message for a general
command, and an inquiry packet for an inquiry
command) of the previous command to be received
before sending the next command.
Command
RxD
TxD
ACK Completion
Within 4V
Within 4V
Inquiry commands
Command
RxD
Inquiry Packet
*1V=16.7 msec (NTSC, 1080/59.94i, 720/59.94p), 20 msec (PAL, 1080/
50i, 720/50p)
TxD
16 Bytes
4
Command and inquiry
Socket number
•Command
When command messages are sent to the BRC-H900, it
is normal to send the next command message after
receiving the completion message or error message.
However, to deal with advanced uses, the BRC-H900
has two buffers (memories) for commands, so that up to
two commands including the commands currently being
executed can be received. (There is a wait longer than a
1V cycle between commands.) However, depending on
the command, it may be necessary to wait until the first
command is completed. When the BRC-H900 receives
commands, it notifies the sender which command buffer
was used, using the socket number of the ACK message.
As the completion message or error message also has a
socket number, it indicates which command has ended.
Even when two command buffers are being used, a
BRC-H900 management command and some inquiry
messages can be executed.
Sends operational commands to the BRC-H900.
•Inquiry
Used for inquiring about the current state of the BRC-
H900.
Command Packet
Note
1)
Inquiry
1)
8X QQ RR ... FF
QQ = Command/Inquiry,
2)
RR = category code
QQ = 01 (Command), 09 (Inquiry)
RR = 00 (Interface), 04 (camera 1), 06 (Pan/Tilter)
2)
X = 1 to 7: BRC-H900 address
For actual values to be sent, see Command Lists or
Inquiry Command Lists.
The ACK message is not returned for these commands
and inquiries, and only the completion message of
socket number 0 is returned.
Responses for commands and inquiries
•ACK message
Returned by the BRC-H900 when it receives a
command. No ACK message is returned for an
inquiry.
Command execution cancel
To cancel a command which has already been sent, send
a Cancel command as the next command. To cancel one
of two commands which have been sent, use the cancel
message.
•Completion message
Returned by the BRC-H900 when execution of
commands or inquiries is completed. In the case of
inquiry commands, reply data for the inquiry is
contained after the 3rd byte of the packet. If the ACK
message is omitted, the socket number will contain 0.
Cancel Packet
8X 2Y FF
Note
Y = socket number
Cancel
X = 1 to 7: BRC-H900 address, Y = socket number
Reply Packet
X0 4Y FF
X0 5Y FF
Note
Error message “Command canceled” will be returned
for this command, but this is not a fault. It indicates that
the command has been canceled.
Ack
Y = socket number
Y = socket number
Y = socket number
Completion (Commands)
Completion (Inquiries)
X0 5Y ... FF
X = 9 to F: BRC-H900 address + 8
Note
•Error message
To cancel a command when VISCA PAN-TILT Drive
(page 12) is being executed, wait at least 200 msec after
executing. Then send a cancel command to ensure that
PAN-TILT Drive stops effectively.
When a command or inquiry command could not be
executed or failed, an error message is returned
instead of a completion message.
To execute a PAN-TILT Drive command again, wait at
least 200 msec after the message “Command canceled”
has appeared.
Error Packet
X0 6Y 01 FF
X0 6Y 02 FF
X0 6Y 03 FF
X0 6Y 04 FF
X0 6Y 05 FF
X0 6Y 41 FF
Description
Message length error
Syntax Error
Command buffer full
Command canceled
No socket (to be canceled)
Command not executable
X = 9 to F: BRC-H900 address + 8, Y = socket number
5
VISCA Device Setting Command
Before starting control of the BRC-H900, be sure to
send the Address command and the IF_Clear command
using the broadcast function.
For VISCA network administration
•Address
Sets an address of a peripheral device. Use when
initializing the network, and receiving the following
network change message.
•Network Change
Sent from the peripheral device to the controller when
a device is removed from or added to the network. The
address must be re-set when this message is received.
Packet
88 30 01 FF
X0 38 FF
Note
Address
Network Change
Always broadcasted.
X = 9 to F: BRC-H900 address + 8
VISCA interface command
•IF_Clear
Clears the command buffers in the BRC-H900.
When cleared, the operation currently being executed
is not guaranteed.
Command Packet
8X 01 00 01 FF
88 01 00 01 FF
Reply Packet
X0 50 FF
88 01 00 01 FF
Note
IF_Clear
IF_Clear (broadcast)
X = 1 to 7: BRC-H900 address (For inquiry packet)
X = 9 to F: BRC-H900 address +8 (For reply packet)
VISCA interface and inquiry
•CAM_VersionInq
Returns information on the VISCA interface.
Inquiry
Inquiry Packet Reply Packet
Description
CAM_VersionInq 8X 09 00 02 FF Y0 50 GG GG HH HH JJ JJ KK FF GGGG = Vender ID
(0001: Sony)
HHHH = Model ID
0501: BRC-H700
0502: BRU-H700
0505: BRC-Z700
0507: BRC-Z330
050B: BRC-H900
JJJJ = ROM revision
KK = Maximum socket # (02)
X = 1 to 7: BRC-H900 address (For inquiry packet)
X = 9 to F: BRC-H900 address +8 (For reply packet)
6
VISCA Command/ACK Protocol
Command
Command Message Reply Message
Comments
General Command 81 01 04 38 02 FF
(Example)
90 41 FF (ACK)+90 51 FF Returns ACK when a command has been accepted, or
(Completion)
Completion when a command has been executed.
90 42 FF 90 52 FF
81 01 04 38 FF
(Example)
90 60 02 FF
(Syntax Error)
Accepted a command which is not supported or a command
lacking parameters.
81 01 04 38 02 FF
(Example)
90 60 03 FF
(Command Buffer Full)
Could not accept the command as there are two commands
currently being executed.
81 01 04 08 02 FF
(Example)
90 61 41 FF
(Command Not Executable)
90 62 41 FF
Could not execute the command in the current mode.
Inquiry Command 81 09 04 38 FF
(Example)
90 50 02 FF (Completion) Does not return ACK.
81 09 05 38 FF
(Example)
90 60 02 FF
(Syntax Error)
Accepted an incompatible command.
Address Set
88 30 01 FF
88 30 02 FF
The device address number plus 1 is returned.*
The same command is returned.
IF_Clear
88 01 00 01 FF
88 01 00 01 FF
(Broadcast)
IF_Clear (For x)
Command Cancel
8x 01 00 01 FF
8x 2y FF
z0 50 FF (Completion)
ACK is not returned for this command.
z0 6y 04 FF
(Command Canceled)
Returned when the command of the socket specified is
canceled. Completion for the command canceled is not
returned.
z0 6y 05 FF
(No Socket)
Returned when the command of the specified socket has
already been completed or when the socket number specified
is wrong.
* When the camera address selector is set to an address other than 0, the value x in 88 30 0x FF will be variable.
Do not transmit the command (except Address Set,
any menu is displayed on the screen. If displayed, clear
the menu first using MENU Display OFF (page 13)
Command, and then proceed.
7
VISCA Camera-Issued Messages
ACK/Completion Messages
Command
Command Message
Comments
ACK
z0 4y FF
(y: Socket No.)
Returned when the command is accepted.
Completion
z0 5y FF
Returned when the command has been executed.
(y: Socket No.)
z = Device address + 8
Error Messages
Command
Command Message
Comments
Syntax Error
z0 60 02 FF
Returned when the command format is different or when a command with
illegal command parameters is accepted.
Command Buffer Full
Command Canceled
z0 60 03 FF
Could not accept a command that is received while two commands are
currently being executed (two sockets have been used).
z0 6y 04 FF
(y: Socket No.)
Returned when a command which is being executed in a socket specified by
the cancel command is canceled. The completion message for the command
is not returned.
No Socket
z0 6y 05 FF
(y: Socket No.)
Returned when no command is executed in a socket specified by the cancel
command, or when an invalid socket number is specified.
Command Not Executable z0 6y 41 FF
(y: Socket No.)
Returned when a command cannot be executed due to current conditions.
For example, when a command for controlling the manual focus is received
during the auto focus mode.
Network Change Message
Command
Command Message
Comments
Network Change
z0 38 FF
Issued when power is supplied to the camera.
8
BRC-H900 Commands
BRC-H900 Command List (1/5)
Command Set
Command
FULL AUTO
MANUAL
Command Packet
8x 01 04 39 00 FF
Comments
EXPOSURE
MODE
8x 01 04 39 03 FF
SHUTTER Pri 8x 01 04 39 0A FF
IRIS Pri 8x 01 04 39 0B FF
BACK LIGHT 8x 01 04 33 02 FF
SPOT LIGHT 8x 01 04 3A 02 FF
Available only when MODE is set to FULL
AUTO.
IRIS
Reset
8x 01 04 0B 00 FF
When EXPOSURE MODE is set to MANUAL or
IRIS Pri, the setting is F5.6.
Up (OPEN)
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
Down
(CLOSE)
Direct
8x 01 04 4B 00 00 0p 0q FF pq: See the VISCA Command Setting Values
(IRIS) section
SHUTTER
Reset
8x 01 04 0A 00 FF
When EXPOSURE MODE is set to MANUAL or
SHUTTER Pri, the setting is 1/60 (for 1080/
59.94i, 720/59.94p).
When EXPOSURE MODE is set to MANUAL or
SHUTTER Pri, the setting is 1/50 (for 1080/50i,
720/50p).
Up (HIGH)
8x 01 04 0A 02 FF
Down (LOW) 8x 01 04 0A 03 FF
Direct
8x 01 04 4A 00 00 0p 0q FF pq: See the VISCA Command Setting Values
(SHUTTER) section
GAIN
Reset
8x 01 04 0C 00 FF
When EXPOSURE MODE is set to MANUAL,
the setting is 0dB.
Up
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
Down
Direct
8x 01 04 4C 00 00 0p 0q FF pq: See the VISCA Command Setting Values
(GAIN) section
AE SPEED
AE LEVEL
Direct
Reset
Up
8x 01 04 5D 0p FF
8x 01 04 0E 00 FF
8x 01 04 0E 02 FF
8x 01 04 0E 03 FF
p 1: LOW 2: MID 3: HIGH
Down
Direct
ON/OFF
Direct
Direct
Direct
8x 01 04 4E 00 00 00 0p FF p 5: -1.0 6: -0.5 7: 0 8: +0.5 9: +1.0
AGC
8x 01 7E 01 75 0p FF
8x 01 04 2C 0p FF
p 2: ON 3: OFF
AGC LIMIT
AGC POINT
p 0: 3dB 1: 6dB 2: 9dB 3: 12dB 4: 18dB
p 0: F5.6 1: F4 2: F2.8
p 2: ON 3: OFF
8x 01 7E 01 76 0p FF
8x 01 7E 01 77 0p FF
AUTO
SHUTTER
SHUTTER
LIMIT
Direct
Direct
8x 01 7E 01 78 0p FF
8x 01 7E 01 79 0p FF
p 0: 1/100 1: 1/125 2: 1/250 3: 1/500
p 0: F5.6 1: F8 2: F11 3: F16
SHUTTER
POINT
9
BRC-H900 Command List (2/5)
Command Set
Command
Command Packet
Comments
COLOR
WHITE
BALANCE
-
8x 01 04 35 0p FF
p 0: AUTO 1: INDOOR 2: OUTDOOR 3: ONE
PUSH 5: MANUAL
One Push WB
Trigger
-
8x 01 04 10 05 FF
R.GAIN
B.GAIN
Reset
Up
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
Down
Direct
Reset
Up
8x 01 04 43 00 00 0p 0q FF pq: 00 (-128) - 80 (0) - FF (+127)
8x 01 04 04 00 FF
8x 01 04 04 02 FF
Down
Direct
-
8x 01 04 04 03 FF
8x 01 04 44 00 00 0p 0q FF pq: 00 (-128) - 80 (0) - FF (+127)
SPEED
8x 01 04 56 0p FF
p: (Slow) 1, 2, 3, 4, 5 (Fast)
OFFSET
Reset
Up
8x 01 7E 01 2E 00 00 FF
8x 01 7E 01 2E 00 02 FF
8x 01 7E 01 2E 00 03 FF
8x 01 7E 01 2E 01 0p FF
8x 01 7E 01 3D 0p FF
Down
Direct
-
p: 0 (-7) - 7 (0) - E (+7)
MATRIX
LEVEL
p: 2 ON (STD) 3: OFF 4: ON (HIGH SAT)
5: ON (FL LIGHT)
Reset
Up
8x 01 04 09 00 FF
8x 01 04 09 02 FF
8x 01 04 09 03 FF
Down
Direct
Reset
Up
8x 01 04 49 00 00 00 0p FF p: 0 (-7) - 7 (0) - E (+7)
8x 01 04 0F 00 FF
PHASE
8x 01 04 0F 02 FF
Down
Direct
Direct
Direct
Direct
Direct
Direct
Direct
ON/OFF
Reset
Up
8x 01 04 0F 03 FF
8x 01 04 4F 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
R-G
8x 01 7E 01 7A 0p 0q FF
8x 01 7E 01 7B 0p 0q FF
8x 01 7E 01 7C 0p 0q FF
8x 01 7E 01 7D 0p 0q FF
8x 01 7E 01 7E 0p 0q FF
8x 01 7E 01 7F 0p 0q FF
8x 01 7E 01 60 0p FF
8x 01 04 02 00 FF
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
p 2: ON 3: OFF
R-B
G-R
G-B
B-R
B-G
DETAIL
DETAIL
LEVEL
8x 01 04 02 02 FF
Down
Direct
Direct
Direct
Direct
Direct
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
FREQUENCY
CRISPENING
H/V RATIO
8x 01 7E 01 61 0p 0q FF
8x 01 7E 01 62 0p 0q FF
8x 01 7E 01 63 0p 0q FF
8x 01 7E 01 64 0p 0q FF
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
WHITE
LIMITTER
BLACK
LIMITTER
Direct
-
8x 01 7E 01 65 0p 0q FF
8x 01 7E 01 66 0p FF
8x 01 7E 01 67 0p 0q FF
pq: 00 (-99) - 63 (00) - C6 (+99)
p: 0 NAM 1: G 2: G+R 3: Y
pq: 00 (-99) - 63 (00) - C6 (+99)
V DTL
CREATION
KNEE APT
LEVEL
Direct
* Number in ( ) is MENU display values.
10
BRC-H900 Command List (3/5)
Command Set
Command
Command Packet
8x 01 7E 01 68 0p FF
8x 01 7E 01 69 0p 0q FF
8x 01 7E 01 6A 0p FF
Comments
COLOR
DETAIL
COLOR DETAIL
-
p 2: ON 3: OFF
LEVEL
Direct
-
pq: 00 (-99) - 63 (00) - C6 (+99)
p 2: ON 3: OFF
AREA
INDICATION
SATURATION
PHASE
Direct
Direct
Direct
-
8x 01 7E 01 6B 0p 0q FF
pq: 00 (-99) - 63 (00) - C6 (+99)
8x 01 7E 01 4D 00 0p 0q 0r FF pqr: 000 - 167 (h)
WIDTH
8x 01 7E 01 6C 0p 0q FF
8x 01 7E 01 6D 0p FF
8x 01 7E 01 54 0p FF
pq: 00 (0) - 28 (40) - 5A (90)
KNEE
MODE
p 2: ON 3: OFF
AUTO KNEE
POINT
-
p 0: Auto 4: Off
Direct
Direct
Direct
8x 01 7E 01 6E 0p 0q FF
8x 01 7E 01 6F 0p 0q FF
8x 01 7E 01 70 0p 0q FF
pq: 32 (50) - 5A (90) - 6D (109)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (00) - 32 (50) - 63 (+99)
SLOPE
KNEE SAT
LEVEL
GAMMA
MODE
-
8x 01 04 5B 0p FF
p: 0 STD3 1: CINEMA1 2: STD1 3: STD2
4: STD4 5: CINEMA2 6: CINEMA3
7: CINEMA4
LEVEL
BLACK
Direct
Direct
Direct
8x 01 7E 01 71 0p 0q FF
8x 01 7E 01 73 0p 0q FF
8x 01 7E 01 72 0p 0q FF
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
pq: 00 (-99) - 63 (00) - C6 (+99)
BLACK
GAMMA
FLICKER
CANCEL
MODE
-
8x 01 04 32 0p FF
8x 01 7E 01 74 0p FF
8x 01 04 38 0p FF
8x 01 04 38 10 FF
p 2: ON 3: OFF
FREQUENCY
MODE
-
0: 50Hz 1: 60Hz
p 2: Auto 3: Manual
FOCUS
ON/OFF
Except ON/
OFF
One Push AF
Trigger
-
8x 01 04 18 01 FF
8x 01 04 18 02 FF
FOCUS ∞
-
PAN TILT
PAN TILT Limit Limit Set
8x 01 06 07 00 0W 0Yp 0Yq W: 1=UpRight 0=DownLeft
0Yr 0Ys 0Yt 0Zp 0Zq 0Zr 0Zs Yp Yq Yr Ys Yt Zp Zq Zr Zs: See Pan/Tilt
FF
Position (for reference) in the VISCA
Command Setting Values section
Limit Clear
8x 01 06 07 01 0W 07 0F 0F
0F 0F 07 0F 0F 0F FF
RAMP CURVE
IR RECEIVE
-
-
8x 01 06 31 0p FF
8x 01 06 08 pq FF
p: 2 MODE1 3 MODE2
SYSTEM
pq: 02 ON 03 OFF 10 ON/OFF Toggle
movement
IMG FLIP
-
8x 01 04 66 0p FF
p: 2 ON 3: OFF
p: 1 ON 0: OFF
p: 1 ON 0: OFF
p: 2 ON 3: OFF
p: 0 HD 3: SD
RAN REVERSE
TILT REVERSE
DISPLAY INFO
SYNC MASTER
HPHASE
-
8x 01 7E 01 06 00 0p FF
8x 01 7E 01 09 00 0p FF
8x 01 7E 01 18 0p FF
8x 01 7E 01 2C 0p FF
8x 01 7E 01 3E 00 02 FF
8x 01 7E 01 3E 00 03 FF
-
-
-
Up
Down
Direct
8x 01 7E 01 5B 00 0p 0q 0r FF pqr: 000 - 3BF
STEADY SHOT
COLOR BAR
TALLY MODE
-
-
-
8x 01 04 34 pq FF
p: 2 ON 3: OFF
8x 01 04 7D 0p FF
p: 2 ON 3: OFF
8x 01 7E 01 0A 01 0q FF
q: 0 OFF 4: ON (LOW) 5: ON (HIGH)
11
BRC-H900 Command List (4/5)
Command Set
VIDEO OUT
Command
Command Packet
8x 01 7E 01 03 00 0p FF
Comments
p: 0 RGB 1: YPbPr
D-SUB 15
FORMAT
-
ADD
-
8x 01 7E 01 07 00 0p FF
p: 0 RGB SYNC OFF 2: RGB SYNCON
SYNC(RGB)
SYNC TYPE
IMG SIZE
-
-
8x 01 7E 01 1A 00 0p FF
8x 01 7E 01 3C 0p FF
p: 0 3-state SYNC 1: VD
p: 0 4: 3 [SQUEEZE] 1 16: 9 [LETTER] 2 4:
3 [CROP]
SETUP
ON/OFF
-
-
-
-
8x 01 7E 01 3F 0p FF
8x 01 04 00 0p FF
8x 01 7E 01 0B 0p qq FF
p: 0 ON (7.5IRE) 1: OFF (0IRE)
p: 2 ON 3: OFF
p: Preset number of speed setting -1 (0-F)
qq: p position direction speed 01-18 (h)
POWER
PRESET Drive
Speed
TALLY
PAN-TILT Drive Up
Down
ON/OFF
-
-
-
-
-
-
-
-
-
-
-
8x 01 7E 01 0A 00 0p FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
VV: PAN speed 00-18 (h)
WW: TILT speed 00-18 (h)
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
ABS (Absolute
Position)
8x 01 06 02 VV 00 0Yp 0Yq 0Yr VV: Speed 00-18 (h)
0Ys 0Yt 0Zp 0Zq 0Zr 0Zs FF
REL (Relative
Position)
-
8x 01 06 03 VV 00 0Yp 0Yq 0Yr Yp Yq Yr Ys Yt Zp Zq Zr Zs: See Pan/Tilt
0Ys 0Yt 0Zp 0Zq 0Zr 0Zs FF
Position (for reference) in the VISCA
Command Setting Values section
Home
Reset
-
-
-
-
8x 01 06 04 FF
8x 01 06 05 FF
8x 01 04 22 0p 0q 0r 0s FF
CAMERA ID
Setting
pqrs: 0000 - FFFF
TITLE Display Title Set1
(Preset Position)
-
8x 01 7E 01 14 uu vv 0w 0! 00 00 uu: Character start position display, H position
00 00 00 00 00 FF
00-1A
vv: Character start position display, V position
00-0D
w: Blinking character display 1 ON, 0 OFF
!: Preset number of character display -1 0-F
Title Set2
Title Set3
-
-
8x 01 7E 01 15 0! aa bb cc dd ee !: Preset number of character display -1 0-F
ff gg hh ii jj FF
aa bb cc dd ee ff gg hh ii jj: First 10 characters
setting (ASCII CODE 0x20-0x7E)
8x 01 7E 01 16 0! kk ll mm nn oo !: Preset number of character display -1 0-F
pp qq rr ss tt FF
kk ll mm nn oo pp qq rr ss tt: Last 10
characters setting (ASCII CODE 0x20-0x7E)
Title Clear
Title On
Title Off
-
-
-
8x 01 7E 01 17 0! 00 FF
8x 01 7E 01 17 02 FF
8x 01 7E 01 17 03 FF
!: Preset number of character display -1 0-F
12
BRC-H900 Command List (5/5)
Command Set
Command
Command Packet
Comments
TITLE Display Title Set1
(Standard)
-
8x 01 7E 01 10 uu vv 0w 00 uu: Character start position display, H position
00-1A
00 00 00 00 00 00 FF
vv: Character start position display, V position
00-0D
w: Blinking character display 1 ON, 0 OFF
Title Set2
Title Set3
-
-
8x 01 7E 01 11 aa bb cc dd aa bb cc dd ee ff gg hh ii jj: First 10 characters
setting (ASCII CODE 0x20-0x7E)
8x 01 7E 01 12 kk ll mm nn kk ll mm nn oo pp qq rr ss tt: Last 10 characters
ee ff gg hh ii jj FF
setting (ASCII CODE 0x20-0x7E)
oo pp qq rr ss tt FF
8x 01 7E 01 13 00 FF
8x 01 7E 01 13 02 FF
8x 01 7E 01 13 03 FF
8x 01 06 06 03 FF
Title Clear
Title On
Title Off
-
-
-
-
MENU Display
OFF
-
PRESET
Set
-
-
-
-
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 07 00 FF
Reset
Recall
Stop
p: Preset number -1 0-F
p: 0 (Slow) to 7 (Fast)
Zoom
Tele (Standard
Speed)
Wide (Standard
Speed)
Tele (Variable
Speed)
Wide (Variable
Speed)
-
-
-
-
-
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
Direct
8x 01 04 47 0p 0q 0r 0s FF pqrs: See the VISCA Command Setting Values
(ZOOM) section
FOCUS
Stop
Far (Standard
Speed)
-
-
8x 01 04 08 00 FF
8x 01 04 08 02 FF
Near (Standard
Speed)
Far (Variable
Speed)
Near (Variable
Speed)
Direct
-
-
-
-
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
p: 0 (Slow) to 7 (Fast)
8x 01 04 48 0p 0q 0r 0s FF pqrs: See the VISCA Command Setting Values
(FOCUS) section
BRBK-SA1 Command
D-SUB 9Pin OUT1
-
-
-
-
8x 01 7E 01 24 0p 0q FF
8x 01 7E 01 25 0p 0q FF
8x 01 7E 01 26 0p 0q FF
8x 01 7E 01 27 0p 0q FF
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 0 RGB 1 YCbCr
D-SUB 9Pin OUT2
RGB SYNC
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 0 Y/C 1 VBS
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 2 SYNC OFF 3 SYNC ON RGB
IMG SIZE
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 0 4: 3 [SQUEEZE] 1 16: 9 [LETTER] 2 4: 3
[CROP]
SETUP
-
-
8x 01 7E 01 3B 0p 0q FF
8x 01 7E 01 43 0p 0q FF
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 0 ON (7.5IRE) 1 OFF (0IRE)
BRBK-HSD2 Command
IMG SIZE
p: 0 Main Unit Card Slot 1 BRU-SF10 Card Slot
1 2 BRU-SF10 Card Slot 2
q: 0 4: 3 [SQUEEZE] 1 16: 9 [LETTER] 2 4: 3
[CROP]
13
BRC-H900 Inquiry Command List (1/3)
Inquiry Command
Command Packet Inquiry Packet
Comments
EXPOSURE MODE FULL AUTO
8x 09 04 39 FF
y0 50 0p FF
p: 0 FULL AUTO 3 MANUAL A
SHUTTER Pri B IRIS Pri
IRIS Pri
SHUTTER Pri
MANUAL
Inquiry
BACK LIGHT ON/ 8x 09 04 33 FF
OFF Inquiry
y0 50 0p FF
y0 50 0p FF
p: 2 ON 3: OFF
p: 2 ON 3: OFF
SPOT LIGHT ON/
OFF Inquiry
8x 09 04 3A FF
8x 09 04 4B FF
8x 09 04 4A FF
8x 09 04 4C FF
IRIS
SHUTTER
-
-
-
y0 50 00 00 0p 0q FF pq: See the VISCA Command
Setting Values (IRIS) section
y0 50 00 00 0p 0q FF pq: See the VISCA Command
Setting Values (SHUTTER) section
GAIN
y0 50 00 00 0p 0q FF pq: See the VISCA Command
Setting Values (GAIN) section
AE SPEED
AE LEVEL
-
-
8x 09 04 5D FF
8x 09 04 4E FF
y0 50 0p FF
p 1: LOW 2: MID 3: HIGH
y0 50 00 00 00 0p FF p 5: -1.0 6: -0.5 7: 0 8: +0.5
9: +1.0
AGC
ON/OFF Inquiry
-
8x 09 7E 01 75 FF
y0 50 0p FF
p: 2 ON 3: OFF
AGC LIMIT
8x 09 04 2C 0p FF y0 50 0p FF
p 0: 3dB 1: 6dB 2: 9dB 3: 12dB
4: 18dB
AGC POINT
-
-
8x 09 7E 01 76 FF
8x 09 7E 01 77 FF
y0 50 0p FF
y0 50 0p FF
p 0: F5.6 1: F4 2: F2.8
p 2: ON 3: OFF
AUTO
SHUTTER
SHUTTER
LIMIT
-
8x 09 7E 01 78 FF
8x 09 7E 01 79 FF
8x 09 04 35 FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
p 0: 1/100 1: 1/125 2: 1/250
3: 1/500
SHUTTER
POINT
-
p 0: F5.6 1: F8 2: F11 3: F16
COLOR
WHITE
MODE Inquiry
BALANCE
R.GAIN
B.GAIN
SPEED
OFFSET
MATRIX
LEVEL
PHASE
R-G
-
-
-
-
-
-
-
-
-
-
-
-
-
8x 09 04 43 FF
8x 09 04 44 FF
8x 09 04 56 FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 0p FF
8x 09 7E 01 2E FF y0 50 00 00 00 0p FF p: 0 (-7) - 7 (0) - E (+7)
8x 09 7E 01 3D FF y0 50 0p FF
8x 09 04 49 FF
8x 09 04 4F FF
y0 50 00 00 00 0p FF p: 0 (-7) - 7 (0) - E (+7)
y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7A FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7B FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7C FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7D FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7E FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 7F FF y0 50 00 00 00 0p FF pq: 00 (-99) - 63 (00) - C6 (+99)
R-B
G-R
G-B
B-R
B-G
* Number in ( ) is MENU display values.
14
BRC-H900 Inquiry Command List (2/3)
Inquiry Command
Command Packet
Inquiry Packet
Comments
DETAIL
DETAIL
-
-
-
-
-
-
8x 09 7E 01 60 FF
8x 09 04 42 FF
y0 50 0p FF
LEVEL
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
FREQUENCY
CRISPENING
H/V RATIO
8x 09 7E 01 61 FF
8x 09 7E 01 62 FF
8x 09 7E 01 63 FF
8x 09 7E 01 64 FF
WHITE
LIMITTER
BLACK
LIMITTER
-
-
-
-
8x 09 7E 01 65 FF
8x 09 7E 01 66 FF
8x 09 7E 01 67 FF
8x 09 7E 01 68 FF
8x 09 7E 01 69 FF
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
V DTL
CREATION
y0 50 0p FF
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 0p FF p 2: ON 3: OFF
p: 0 NAM 1: G 2: G+R 3: Y
KNEE APT
LEVEL
COLOR
DETAIL
COLOR
DETAIL
LEVEL
-
-
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
p 2: ON 3: OFF
AREA
8x 09 7E 01 6A FF y0 50 0p FF
INDICATION
SATURATION -
8x 09 7E 01 6B FF y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
8x 09 7E 01 4D FF y0 50 00 00 0p 0q FF pqr: 000 - 167
PHASE
-
-
-
-
-
-
-
WIDTH
MODE
8x 09 7E 01 6C FF y0 50 00 00 0p 0q FF pq: 00 (0) - 28 (40) - 5A (90)
KNEE
8x 09 7E 01 6D FF y0 50 0p FF
8x 09 7E 01 54 FF y0 50 0p FF
p 2: ON 3: OFF
p 0: Auto 4: Off
AUTO KNEE
POINT
8x 09 7E 01 6E FF y0 50 00 00 0p 0q FF pq: 32 (50)
SLOPE
8x 09 7E 01 6F FF y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
KNEE SAT
LEVEL
8x 09 7E 01 70 FF
y0 50 00 00 0p 0q FF pq: 00 (00) - 32 (50) - 63 (+99)
GAMMA MODE
-
8x 09 04 5B FF
y0 50 0p FF
p: 0 STD3 1: CINEMA1 2: STD1
3: STD2 4: STD4 5: CINEMA2
6: CINEMA3 7: CINEMA4
LEVEL
BLACK
-
-
-
8x 09 7E 01 71 FF
8x 09 7E 01 73 FF
8x 09 7E 01 72 FF
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
y0 50 00 00 0p 0q FF pq: 00 (-99) - 63 (00) - C6 (+99)
BLACK
GAMMA
FLICKER MODE
CANCEL
-
-
-
-
8x 09 04 32 FF
8x 09 7E 01 74 FF
8x 09 04 38 FF
8x 09 06 31 FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
p 2: ON 3: OFF
FREQUENCY
p 0: 50Hz 1: 60Hz
p 2: Auto 3: Manual
p: 2 MODE1 3 MODE2
FOCUS
MODE
PAN TILT RAMP
CURVE
SYSTEM IR RECEIVE
IMG FLIP
-
-
-
8x 09 06 08 FF
8x 09 04 66 FF
8x 09 7E 01 06 FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
p: 2 ON 3: OFF
p: 2 ON 3: OFF
p: 1 ON 0: OFF
RAN
REVERSE
TILT
REVERSE
-
-
-
8x 09 7E 01 09 FF
8x 09 7E 01 18 FF
y0 50 0p FF
y0 50 0p FF
p: 1 ON 0: OFF
p: 2 ON 3: OFF
p: 0 HD 3: SD
DISPLAY
INFO
SYNC
8x 09 7E 01 2C FF y0 50 0p FF
MASTER
HPHASE
-
-
8x 09 7E 01 3E FF y0 50 00 0p 0q 0r FF pqr: 000 - 3BF
STEADY
SHOT
8x 09 04 34 FF
y0 50 0p FF
p: 2 ON 3: OFF
COLOR BAR
-
8x 09 04 7D FF
y0 50 0p FF
p: 2 ON 3: OFF
15
BRC-H900 Inquiry Command List (3/3)
Inquiry Command
Command Packet
8x 09 7E 01 03 FF
Inquiry Packet
y0 50 0p FF
Comments
p: 0 RGB 1: YPbPr
VIDEO
OUT
D-SUB 15
FORMAT
-
ADD
SYNC(RGB)
-
8x 09 7E 01 07 FF
y0 50 0p FF
p: 0 RGB SYNC OFF 2: RGB
SYNCON
SYNC TYPE
IMG SIZE
-
-
8x 09 7E 01 1A FF
8x 09 7E 01 3C FF
y0 50 0p FF
y0 50 0p FF
p: 0 3-state SYNC 1: VD
p: 0 4: 3 [SQUEEZE] 1 16: 9
[LETTER] 2 4: 3 [CROP]
SETUP
D-SUB 9Pin
OUT1
-
-
8x 09 7E 01 3F FF
y0 50 0p FF
p: 0 ON (7.5IRE) 1: OFF (0IRE)
BRBK-
SA1
8x 09 7E 01 24 0p FF y0 50 0q FF
8x 09 7E 01 25 0p FF y0 50 0q FF
8x 09 7E 01 26 0p FF y0 50 0q FF
8x 09 7E 01 27 0p FF y0 50 0q FF
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 0 RGB 1 YCbCr
D-SUB 9Pin
OUT2
-
-
-
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 0 Y/C 1 VBS
RGB SYNC
IMG SIZE
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 2 SYNC OFF 3 SYNC ON RGB
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 0 4: 3 [SQUEEZE] 1 16: 9
[LETTER] 2 4: 3 [CROP]
SETUP
-
-
8x 09 7E 01 3B 0p FF y0 50 0q FF
8x 09 7E 01 43 0p FF y0 50 0q FF
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 0 ON (7.5IRE) 1 OFF (0IRE)
BRBK-
HSD2
IMG SIZE
p: 0 Main Unit Card Slot 1 BRU-
SF10 Card Slot 1 2 BRU-SF10
Card Slot 2
q: 0 4: 3 [SQUEEZE] 1 16: 9
[LETTER] 2 4: 3 [CROP]
POWER
Status
CAMERA
Software
Version
ON/OFF
Inquiry
-
-
-
8x 09 7E 04 00 FF
8x 09 00 02 FF
y0 50 0p FF
p: 2 ON 3: OFF
y0 50 00 01
mn pq rs tu vw FF
mnpq: Model Code (05xx)
rstu: ROM version
vw: Socket Number (02)
PRESET
Drive
Speed
-
-
8x 09 7E 01 0B 0p FF y0 50 qq FF
p: Preset number of speed retrieving
-1 (0-F)
qq: p position direction speed
response 01-18 (h)
TALLY
PAN-TILT
Position
-
-
-
-
8x 09 7E 01 0A FF
8x 09 06 12 FF
y0 50 0p FF
p: 2 ON 3: OFF
y0 50 Yp Yq Yr Ys Yp Yq Yr Ys Yt Zp Zq Zr Zs: See
Yt Zp Zq Zr Zs FF
Pan/Tilt Position (for reference) in
the VISCA Command Setting
Values section
CAMERA
ID
TITLE
(Preset
Postion)
TITLE
Display
(Standard)
-
-
-
8x 09 04 22 FF
y0 50 0p 0q 0r 0s FF pqrs: ID
ON/OFF
Inquiry
8x 09 7E 01 17 FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
y0 50 0p FF
p: 2 ON 3: OFF
ON/OFF
Inquiry
-
-
-
8x 09 7E 01 13 FF
8x 09 06 06 FF
8x 09 04 3F FF
p: 2 ON 3: OFF
p: 2 ON 3: OFF
MENU
Display
Status
ON/OFF
Inquiry
PRESET
-
Return the last preset number which
has been operated (VISCA
parameters [0-F])
Zoom
-
-
-
-
8x 09 04 47 FF
8x 09 04 48 FF
y0 50 0p 0q 0r 0s FF pqrs: See the VISCA Command
Setting Values (ZOOM) section
y0 50 0p 0q 0r 0s FF pqrs: See the VISCA Command
Setting Values (FOCUS) section
FOCUS
16
BRC-H900 Block Inquiry Command List
Lens control system inquiry commands…..Command Packet 8x 09 7E 7E 00 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7
6
5
Destination Address
4
4
4
6
12
3
0
3
3
2
1
0
7
6
5
2
1
0
7
6
5
4
2
1
0
7
6
5
Source Address
0
1
0
1
0
0
0
0
0
0
0
0
4
4
7
1
13
3
3
2
1
3
2
1
0
7
6
5
2
1
0
7
6
5
Focus Mode (1: Auto
0: Manual)
0
7
6
5
4
3
0
0
0
0
0
4
4
8
2
3
3
2
1
0
7
6
5
2
1
0
7
6
5
Focus Position (HH)
Zoom Position (HH)
Camera Memory Recall
(1: Executing
2
1
0
14
0: Stopped)
0
0
0
0
0
0
0
0
Focus Command
(1: Executing
0: Stopped)
Zoom Command
(1: Executing
0: Stopped)
4
4
9
3
3
3
2
1
0
7
6
5
2
1
0
7
6
5
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
Focus Position (HL)
Zoom Position (HL)
0
0
0
0
0
0
0
0
15
4
4
10
3
4
3
2
1
0
7
6
5
2
1
0
7
6
5
Focus Position (LH)
Zoom Position (LH)
0
0
0
0
0
0
0
0
4
4
11
3
5
3
2
1
0
2
1
0
Focus Position (LL)
Zoom Position (LL)
17
Camera control system inquiry commands (1/2)…..Command Packet 8x 09 7E 7E 01 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
4
0
0
7
6
5
0
0
0
7
6
5
Destination Address
COLOR SPEED (1 - 5)
4
4
12
3
0
3
2
1
6
3
EXPOSURE MODE
Manual Gain Position
WHITE BALANCE
MODE
(0: Auto 1: Indoor
2: Outdoor 3: Onepush
5: Manual)
2
1
0
7
6
5
4
2
1
0
7
6
5
Source Address
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
0
0
0
0
0
0
4
1
13
3
2
1
3
7
2
1
0
7
6
5
IMG FLIP MODE
(1: On 0: Off)
0
DETAIL SETTING
(0: Off 1: On)
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
0
0
0
0
7
6
5
4
3
2
1
0
7
6
5
4
0
0
0
0
4
2
3
14
2
1
0
7
6
5
8
AE LEVEL
(5: 1.0 6:-0.5 7: 0
8: +0.5 9: +1.0)
WB R Gain(H)
EXPOSURE MODE
(0: Auto 1: Manual
A: Shutter Pri
0
0
0
0
B: Iris Pri)
1
1
1
1
1
1
1
1
0
0
0
0
4
3
3
15
2
1
0
7
6
5
WB R-Gain (L)
SPOT LIGHT MODE
(1: On 0: Off)
9
3
2
BACK LIGHT MODE
(1: On 0: Off)
0
0
0
0
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
0
0
0
0
0
4
4
3
2
1
0
7
6
5
WB B-Gain (H)
10
EXPOSURE MODE
Manual Shutter Position
0
0
0
0
4
0
0
0
5
3
2
1
0
WB B-Gain (L)
11
EXPOSURE MODE
Manual Iris Position
18
Camera control system inquiry commands (2/2)…..Command Packet 8x 09 7E 7E 02 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
7
6
5
4
0
0
0
0
7
6
5
Destination Address
STEADY SHOT (1: On
0: Off)
4
4
0
11
AGC MODE (1: ON
0: OFF)
3
3
3
5
0
0
2
1
0
7
6
5
Source Address
2
2
1
0
7
6
5
4
AGC LIMIT
(0: 3dB 1: 6dB 2: 9dB
3: 12dB 4: 18dB)
FLICKER CANCEL
(1: On 0: Off)
1
0
1
0
1
0
0
0
0
0
0
0
0
0
FRECKER CANCEL
FREQUENCY (0: 50Hz
1: 60Hz)
0
0
Shutter Point (0: F5.6
1: F8 2: F11 3: F16)
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
0
4
1
Shutter Limit
(0: 1/100 1: 1/125
2: 1/250 3: 1/500)
3
12
3
2
1
0
7
6
5
4
4
Auto Shutter (1: ON
0: OFF)
6
2
3
2
1
0
7
6
5
1
0
7
6
5
AGC Point (0: F5.6 1: F4
2: F2.8)
0
0
0
0
3
2
4
1080/720 mode (1: 1080
0: 720)
13
3
2
1
0
4
7
59.94/50 mode (1: 59.94
0: 50)
3
2
1
0
7
6
5
R-G (H)
2
1
0
7
6
5
Camera status (1: Power
On 0: Sleep)
GAMMA MODE (0 - 7)
0
0
0
0
7
6
5
0
0
0
0
0
0
0
0
4
4
14
3
3
4
3
8
3
2
1
0
7
6
5
2
1
0
7
6
5
R-G (L)
COLOR OFFSET
0 (-7) - 7 (0) - E (+7)
2
1
0
7
6
5
COLOR PHASE (H)
1
1
1
1
1
1
1
1
0
0
0
0
0
MATRIX
(2: On (STD) 3: OFF
4: ON (HIGH SAT)
5: ON (FL LIGHT)
4
15
3
4
4
4
9
3
2
1
0
3
2
1
0
MATRIX
COLOR LEVEL
0 (-7) - 7 (0) - E (+7)
2
1
0
7
6
5
COLOR PHASE (L)
0
0
0
0
0
0
4
10
3
2
1
0
AE SPEED (1: Low
2: Mid 3: High)
19
Other enlargement inquiry commands (1/5) .......... Command Packet 8x 09 7E 7E 03 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
0
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
7
6
5
Destination Address
4
4
4
6
12
3
0
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
G-B (H)
Source Address
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
4
4
4
7
13
3
1
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
G-B (L)
B-G (H)
0
0
0
0
0
0
0
0
4
4
4
8
14
3
2
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
B-R (H)
B-G (L)
R-B (H)
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
4
4
4
9
15
3
3
3
3
2
1
0
7
6
2
1
0
2
1
0
7
6
5
B-R (L)
0
R-B (L)
0
0
0
0
Camera block FAN
rotating status
(1: Rotating 0: Stop)
4
5
COLOR DETAIL (1: On
0: Off)
4
3
10
4
2
1
0
7
6
5
G-R (H)
3
2
1
0
7
6
5
Shutter Pri Position
0
0
0
0
0
0
0
4
5
3
2
1
0
4
G-R (L)
11
3
2
1
0
Iris Pri Position
20
Other enlargement inquiry commands (2/5) .......... Command Packet 8x 09 7E 7E 04 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
0
7
6
5
0
0
0
7
6
5
Destination Address
4
4
4
6
12
3
0
3
3
2
1
0
7
6
5
2
1
0
7
6
5
Gain Current Position
2
1
0
7
6
5
DETAIL LEVEL (H)
Source Address
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
4
4
4
7
13
3
1
3
3
2
1
0
7
6
5
4
2
1
0
7
6
5
DETAIL FREQUENCY
(H)
2
1
0
7
6
5
DETAIL LEVEL (L)
0
0
0
0
0
0
0
COLOR DETAIL AREA
INDICATION (1: ON
0: OFF)
4
4
14
3
2
3
8
2
1
0
7
6
5
DETAIL FREQUENCY
(L)
2
1
0
7
6
5
3
2
1
0
7
6
5
Current R GAIN (H)
COLOR DETAIL
LEVEL (H)
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
4
4
15
3
3
3
4
9
2
1
0
2
1
0
7
6
5
3
Current R GAIN (L)
2
1
0
7
6
5
COLOR DETAIL
LEVEL (L)
0
0
0
0
0
0
4
COLOR DETAIL (1: On
0: Off)
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
10
Current B GAIN (H)
Shutter Current Position
0
0
0
0
0
0
0
4
5
3
2
1
0
Current B GAIN (L)
11
Iris Current Position
21
Other enlargement inquiry commands (3/5) .......... Command Packet 8x 09 7E 7E 05 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
0
7
6
5
0
0
0
0
7
6
5
Destination Address
4
4
4
6
12
3
0
3
3
2
1
0
7
6
5
2
1
0
7
6
5
DETAIL WHITE
LIMITTER (H)
COLOR DETAIL
SATURATION (H)
2
1
0
7
6
5
Source Address
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
4
4
4
7
13
3
1
3
3
2
1
0
7
6
5
2
1
0
7
6
5
DETAIL WHITE
LIMITTER (L)
COLOR DETAIL
SATURATION (L)
2
1
0
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
V DETAIL CREATION
0 - 3
4
4
4
8
14
3
2
3
3
2
1
0
7
6
5
2
1
0
7
6
5
DETAIL BLACK
LIMITTER (H)
2
1
0
7
6
5
DETAIL CRISPENING
(H)
0
0
0
0
0
0
0
0
4
4
4
9
15
3
3
3
3
2
1
0
7
6
5
2
1
0
DETAIL BLACK
LIMITTER (L)
2
1
0
7
6
5
DETAIL CRISPENING
(L)
0
0
0
0
0
0
0
0
4
4
10
3
4
3
2
1
0
7
6
5
2
1
0
7
6
5
KNEE APT LEVEL (H)
DETAIL H/V RATIO (H)
0
0
0
0
0
0
0
0
4
4
11
3
5
3
2
1
0
2
1
0
KNEE APT LEVEL (L)
DETAIL H/V RATIO (L)
22
Other enlargement inquiry commands (4/5) .......... Command Packet 8x 09 7E 7E 06 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
7
6
5
0
0
0
0
7
6
5
Destination Address
AUTO KNEE (1: ON
0: OFF)
4
4
12
3
0
4
KNEE MODE (1: ON
0: OFF)
3
6
2
1
0
7
6
5
2
1
0
7
6
5
3
2
1
0
7
6
5
GAMMA LEVEL (H)
Source Address
KNEE POINT (H)
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
4
4
13
3
1
3
4
7
2
1
0
7
6
5
2
1
0
7
6
5
3
GAMMA LEVEL (L)
2
1
0
7
6
5
KNEE POINT (L)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
4
4
14
3
2
3
4
COLOR DETAIL
PHASE (H)
8
2
1
0
7
6
5
2
1
0
7
6
5
3
2
1
0
7
6
5
KNEE SLOPE (H)
0
0
0
0
0
0
0
0
4
4
15
3
3
3
4
9
2
1
0
2
1
0
7
6
5
COLOR DETAIL
PHASE (L)
3
2
1
0
7
6
5
KNEE SLOPE (L)
0
0
0
0
0
0
0
0
4
4
3
4
10
3
2
1
0
7
6
5
COLOR DETAIL
WIDTH (H)
2
1
0
7
6
5
KNEE SATLEVEL (H)
0
0
0
0
0
0
0
0
4
5
3
4
11
3
2
1
0
COLOR DETAIL
WIDTH (L)
2
1
0
KNEE SATLEVEL (L)
23
Other enlargement inquiry commands (5/5) .......... Command Packet 8x 09 7E 7E 07 FF
Byte Bit
Comments
Byte Bit
Comments
Byte Bit
Comments
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7
6
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
7
6
5
Destination Address
4
4
4
6
12
3
0
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
Source Address
0
1
0
1
0
0
0
0
0
0
0
4
4
4
7
13
3
1
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
4
4
4
8
14
3
2
3
3
2
1
0
7
6
5
2
1
0
7
6
5
2
1
0
7
6
5
BLACK LEVEL (H)
0
0
0
0
4
4
4
9
15
3
3
3
3
2
1
0
7
6
5
2
1
0
2
1
0
7
6
5
BLACK LEVEL (L)
0
0
0
0
4
4
10
3
4
3
2
1
0
7
6
5
2
1
0
7
6
5
BLACK GAMM LEVEL
(H)
0
0
0
0
4
4
11
3
5
3
2
1
0
2
1
0
BLACK GAMM LEVEL
(L)
24
VISCA Command Setting Values
IRIS
GAIN
Parameter
Parameter
p
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
q
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F No.
F1.9 (OPEN)
F2.2
F2.4
F2.6
F2.8
F3.1
F3.4
F3.7
F4
p
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
q
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
Gain (dB)
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
F4.4
F4.8
F5.2
F5.6
F6.2
F6.8
F7.3
F8
8
F8.7
F9.6
F10
7
6
5
F11
4
F12
3
F13
2
F15
1
F16
0
CLOSE
-3
SHUTTER
Parameter
p
0
0
0
0
0
0
0
0
0
0
q
F
E
D
C
B
A
9
Shutter Speed (sec)
1/8000
1/4000
1/2000
1/1000
1/500
1/250
1/125
8
1/120
7
1/100
1/60*
6
*
The setting is 1/60 when the video format is set to 1080/59.94i or 720/
59.94p.
The setting is 1/50 when the video format is set to 1080/50i or 720/50p.
25
Pan/Tilt Position (for reference)
Focus Ratio and Focus Distance
(for reference)
Pan
Focus Ratio
1000
Focus Distance
Left
Right
Angle (degrees)
∞
Yp Yq Yr Ys Yt
00000
Yp Yq Yr Ys Yt
00000
2000
14.6m
6.3m
3.9m
2.8m
2.2m
1.7m
1.4m
1.2m
1.0m
0.9m
0.8m
0
3000
10
00938
FF6C8
FED90
FE458
4000
20
01270
5000
30
01BA8
024E0
02E18
03750
6000
40
FDB20
FD1E8
FC8B0
FBF78
FB640
FAD08
FA3D0
F9A98
F9160
7000
50
8000
60
9000
70
04088
A000
B000
C000
80
049C0
052F8
90
100
110
120
130
140
150
160
169
05C30
06568
Zoom Position and Zoom Ratio (for reference)
06EA0
077D8
08110
F8828
Zoom Position
0000
Zoom Ratio
F7EF0
F75B8
F6C80
F6422
×1
×2
08A48
09380
1140
1A80
×3
09BDE
2180
×4
2740
×5
Tilt
2BC0
2F60
×6
×7
Up
Zp Zq Zr Zs
0000
Down
Angle (degrees)
32A0
×8
Zp Zq Zr Zs
35A0
×9
0
0000
3840
×10
×11
×12
×13
×14
10
20
30
40
50
60
70
80
90
0938
F6C8
3AA0
3CC0
3EC0
4000
1270
ED90
1BA8
24E0
E458
-
-
-
-
-
-
2E18
3750
4088
49C0
52F8
26
Pan/Tilt Status Code List
P
Q
R
S
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – 0 0
0 – 0 1
0 – 1 0
0 – 1 1
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – 0 0
– – 1 0
0 1 – –
1 0 – –
– – – –
– – – –
– – – –
– – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
– – 0 0
– – 1 0
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
0 – – –
– – – 1
– – 1 –
– 1 – –
1 – – –
1 1 1 1
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
Panning reaches the end of the left.
Panning reaches the end of the right.
Tilting reaches the upper limit.
Tilting reaches the lower limit.
Pan/tilt position cannot be detected.
Pan functions normally.
Pan mechanism is defective.
Tilt functions normally.
Tilt mechanism is defective.
Pan/Tilt operating
Pan/Tilt operations complete.
Not initialized
Initializing
Initialization completes.
Initialization failed.
( – : optional)
27
Memory Function (Inquiry Commands)
Preset No.
last operated
pp: Memory number
last operated
Comments
–
00
While no Recall commands are used after the power
has been tuned on
1
2
7F
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
≠00 (or =00 for Reset, Set and Recall commands)
3
4
5
6
7
8
9
10
11
12
13
14
15
16
28
|