43-962A.fm Page 1 Monday, August 16, 1999 3:33 PM
Cat. No. 43-962A
OWNER’S MANUAL
Please read before using this equipment.
System 240
60-Number Memory Caller ID
43-962A.fm Page 3 Monday, August 16, 1999 3:33 PM
FEATURES
The RadioShack System 240 60-Number Memory Caller ID is the latest in tele-
phone technology. When you subscribe to Caller ID service, the telephone com-
pany sends the caller’s name, telephone number, the date, and the time of the
call between the first and second rings. This module stores and displays up to
60 Caller ID records which have either a number, or a name, or both.
The module has these features:
Easy Installation
— so you can quickly begin to see Caller ID information.
Large Display
— makes it easy to see the Caller ID information.
Built-in Error Checking
— checks incoming Caller ID information to ensure it
is accurate.
3
43-962A.fm Page 4 Monday, August 16, 1999 3:33 PM
Trilingual Messages — lets you set the module to display messages in En-
glish, French, or Spanish.
Contrast Control — lets you adjust the display contrast for the best visibility.
This module has been tested and found to comply with all applicable UL and
FCC standards.
Notes:
• To use this module, you must be in an area where Caller ID service is avail-
able, and you must subscribe to the service.
• Your Caller ID module displays name only, number only, or both name and
number, depending upon the information provided by the phone company.
4
43-962A.fm Page 5 Monday, August 16, 1999 3:33 PM
FCC INFORMATION
We have designed your System 240 to conform to federal regulations, and you
can connect it to most telephone lines. However, each system (and each de-
vice, such as a telephone or answering machine) that you connect to the tele-
phone line draws power from the line. We refer to this power draw as the
device’s ringer equivalence number, or REN. The REN is shown on the label on
the bottom of the module.
If you use more than one telephone or other device on the line, add up all of the
RENs. If the total is more than five, your telephone might not ring. In rural areas,
a total REN of three might impair ringer operation. If ringer operation is im-
paired, remove a device from the line.
Your module complies with Part 68 of FCC Rules. You must, upon request, pro-
vide the FCC registration number and the REN to your telephone company.
Both numbers are shown on the bottom of the module.
5
43-962A.fm Page 6 Monday, August 16, 1999 3:33 PM
Note: You must not connect the module to:
• Coin-operated systems
• Party-line systems
• Most electronic key telephone systems
In the unlikely event that your module causes problems on the telephone line,
the telephone company can disconnect your service. The telephone company
attempts to notify you in advance. If advance notice is not practical, the tele-
phone company notifies you as soon as possible and advises you of your right
to file a complaint with the FCC.
Also the telephone company can make changes to its lines, equipment, opera-
tions, or procedures that could affect the operation of this module. The tele-
phone company notifies you of these changes in advance, so you can take the
necessary steps to prevent interruption of your telephone service.
6
43-962A.fm Page 7 Monday, August 16, 1999 3:33 PM
This module complies with the limits for a Class B digital device as specified in
Part 15 of FCC Rules. These limits provide reasonable protection against radio
and TV interference in a residential area. However, your module might cause TV
or radio interference even when it is operating properly. To eliminate interfer-
ence, you can try one or more of the following corrective measures.
• Reorient or relocate the receiving antenna
• Increase the distance between the module and the radio or TV
Consult your local RadioShack store if the problem continues.
7
43-962A.fm Page 8 Monday, August 16, 1999 3:33 PM
CONTENTS
Installing Batteries ......................................................................................... 9
Connecting to the Phone Line .................................................................... 11
Connecting to a Single Line .................................................................... 11
Connecting to a Two-Line, Three-Way Jack ........................................... 13
Connecting to an Answering Machine ..................................................... 15
Mounting the Module ................................................................................... 16
Setting the Display Language ..................................................................... 18
Adjusting the Display Contrast ................................................................... 19
Caller ID Information .................................................................................... 20
Reviewing Call Information ..................................................................... 20
Deleting Call Records ............................................................................. 24
Care and Maintenance ................................................................................. 25
Lightning ................................................................................................. 27
8
43-962A.fm Page 9 Monday, August 16, 1999 3:33 PM
INSTALLING BATTERIES
The System 240 is powered by three AAA batteries. For the longest operation,
we recommend you use alkaline batteries (RadioShack Cat. No. 23-555). Follow
these steps to install the batteries.
Note:
If you are replacing the batteries, unplug the module from the phone line.
1. Press down and slide off the battery compartment cover in the direction of
the arrow.
2. Place the batteries in the compart-
ment, following the correct polarity (+
and –) as marked inside the compart-
ment. The call indicator on the front of
V
A A 1 5 V
+
+
V
the module lights and a test screen
appears. The indicator turns off when
the total memory capacity appears
briefly. Then the screen goes blank.
3. Replace the cover.
9
43-962A.fm Page 10 Monday, August 16, 1999 3:33 PM
When the battery low indicator (
) appears in the top left corner of the dis-
play or the display dims, replace the batteries.
Cautions:
• Once you remove the batteries from the Caller ID module, you have 7 sec-
onds to install new batteries without losing saved information.
• Do not press any buttons after you remove the batteries. Doing so can de-
lete the information stored in the module.
• Do not mix old and new batteries, different types of batteries (standard, al-
kaline, or rechargeable), or rechargeable batteries of different capacities.
10
43-962A.fm Page 11 Monday, August 16, 1999 3:33 PM
CONNECTING TO THE PHONE LINE
CONNECTING TO A SINGLE LINE
The Caller ID module connects to the phone line using a modular telephone-line
connector. If your phone line does not have this type of jack, you can update the
wiring yourself using necessary adapters available at your local RadioShack
store. Or, you can have the telephone company update your telephone wiring
for you.
Note:
The USOC number of the jack to be installed is RJ11C.
11
43-962A.fm Page 12 Monday, August 16, 1999 3:33 PM
Follow these steps to connect the module to the phone line.
R E V I E W
D E
1. Unplug the phone’s cord from the phone line jack and plug this cord into
the module’s PHONE jack.
2. Plug one end of the supplied modular cord into the module’s WALL jack.
3. Plug the other end of the supplied modular cord into the phone line jack.
12
43-962A.fm Page 13 Monday, August 16, 1999 3:33 PM
CONNECTING TO A TWO-LINE, THREE-WAY JACK
You can connect the module to a two-line phone using a two-line, three-way
jack (Cat. No. 279-402). The module only shows information about calls re-
ceived on the line to which it is connected.
Follow these steps to connect the module to a two-line phone.
W
I E
V
E
R
E
T
E
L
D
1. Unplug the phone’s cord from the phone line jack, then plug the two-line,
three-way jack into the phone line jack.
13
43-962A.fm Page 14 Monday, August 16, 1999 3:33 PM
2. Plug the phone’s cord into the L1 + L2 jack on the adapter.
3. Plug one end of the supplied modular cord into the module’s WALL jack.
4. Plug the other end of the modular cord into either the L1 or L2 jack on the
adapter, depending on which line’s calls you want to monitor.
Note: You can also connect two
W
I E
V
E
R
E
T
L
E
D
modules (one module for each
line) as shown here. Each module
shows information for the line you
connect it to. Simply plug the oth-
er module into the remaining jack
W
I E
V
E
R
E
T
E
L
E
D
(L1 or L2) on the adapter.
14
43-962A.fm Page 15 Monday, August 16, 1999 3:33 PM
CONNECTING TO AN ANSWERING MACHINE
1. Unplug the answering machine’s cord
from the phone line jack, then plug the
cord into the module’s PHONE jack.
2. Plug one end of the supplied phone
W
I E
V
E
R
E
T
E
E
D
cord into the WALL jack on the mod-
ule. Then plug the other end of the
cord into the phone line jack.
3. Set the answering machine to answer
calls after at least two rings.
Note:
If you connect a telephone answering machine to the same line as
the Caller ID System 240, you must set the answering machine to answer
in two or more rings in order to receive the Caller ID information.
15
43-962A.fm Page 16 Monday, August 16, 1999 3:33 PM
MOUNTING THE MODULE
You can place the module on a desktop or table, or mount it on a wall. To mount
the System 240 on a wall, you need two wood screws (not supplied).
1. Use the bracket as a template to mark
Screw
Holes
the screw locations, then drill two
holes into the wall.
2. Secure the bracket to the wall by
threading two screws into the bracket.
16
43-962A.fm Page 17 Monday, August 16, 1999 3:33 PM
3. Disconnect the phone lines from the
System 240 and thread them through
the lower opening on the bracket.
4. Reconnect the phone lines to the Sys-
tem 240, then slide the module onto
the bracket, and push the module
down to secure it.
REVIEW
DELETE
17
43-962A.fm Page 18 Monday, August 16, 1999 3:33 PM
SETTING THE DISPLAY LANGUAGE
The System 240 is preset to display mes-
sages in English. To select a language at
any time, hold down both review buttons
until SELECT LANGUAGE appears, then
release the buttons. ESP FRA ENGap-
DELETE
pears. To select Spanish, press
.
REVIEW
To select French, press
. To se-
REVIEW
lect English, press
. After you
DELETE
REVIEW
select the language, the screen again goes
blank, then displays messages in the se-
lected language.
18
43-962A.fm Page 19 Monday, August 16, 1999 3:33 PM
ADJUSTING THE DISPLAY CONTRAST
Follow these steps to adjust the display’s contrast for the best visibility.
DELETE
REVIEW
REVIEW
1. Press either
button so –NOCALLS–(or a call record) appears.
DELETE
Then hold down
.
REVIEW
2. Within 6 seconds, repeatedly press
REVIEW
to decrease the contrast or
to increase it.
DELETE
Note:
If you hold down
for longer than 6 seconds without pressing
button, the system deletes all call records from its memory.
REVIEW
a
DELETE
3. Release
.
19
43-962A.fm Page 20 Monday, August 16, 1999 3:33 PM
CALLER ID INFORMATION
The module automatically displays all received Caller ID information for every
incoming call between the first and second ring. As it receives calls, it stores the
information in the module’s memory for later recall. When the module’s memory
becomes full, any new record replaces the oldest record.
REVIEWING CALL INFORMATION
The System 240 can store up to 60 Caller ID records. If the module has re-
ceived a call since the last time it was reviewed, the call indicator flashes (see
“Deleting Call Records” on Page 24). Press any button to turn off the indicator.
REVIEW
REVIEW
To view the latest call record, press either
or
. Then, to
REVIEW
view other call records, press
to step back through the call records
REVIEW
or
to step forward through them.
20
43-962A.fm Page 21 Monday, August 16, 1999 3:33 PM
Note: The display shows up to 10 digits of the phone number. If the incoming
phone number is longer than 10 digits, the display shows only the last 10 digits.
Display
(English,
French,
Description
Spanish)
Appears the first time you review a call’s infor- XX NEW CALL(S)
mation. XXis the number of new calls that
you have received since you last reviewed
calls.
XX NOUV APPEL(S)
NUEVA LLAMADA
(XX LLAMADAS)
Appears if Caller ID service is not available in -UNAVAILABLE-
the caller’s area. No caller information
appears.
-INCONNU-
-FUERA DE AREA-
21
43-962A.fm Page 22 Monday, August 16, 1999 3:33 PM
Display
(English,
French,
Description
Spanish)
Appears if the caller has elected to block
Caller ID information. Message appears for
about 30 seconds and the call indicator
flashes.
ANONYMOUS CALL
CONFIDENTIEL
LLAMADA ANONIMA
Appears if the Caller ID information was gar- -LINE ERROR-
.
bled Minor electrical disturbances can affect -ERREUR-
the Caller ID information. Occasional errors
are normal. If this message appears fre-
quently, contact your local telephone com-
pany or RadioShack store for assistance.
LINEA CON ERROR
22
43-962A.fm Page 23 Monday, August 16, 1999 3:33 PM
Display
(English,
French,
Description
Spanish)
Appears if there are no call records in the sys- -NO CALLS-
tem’s memory when you press a REVIEW key. -AUCUN APPEL-
NO HAY LLAMADAS
Appears when call information is not sent by
the telephone company. This happens if you
have not subscribed to Caller ID service or if
you answer the call before the second ring.
-NO DATA SENT-
-AUCUNE DONNEE-
SIN INFORMACION
You have reached the end of your call
records. Press the other REVIEW key to see
them again.
-END OF LIST-
-FIN DE LISTE-
-FIN DE LISTA-
23
43-962A.fm Page 24 Monday, August 16, 1999 3:33 PM
DELETING CALL RECORDS
To delete the displayed call record, quickly press DELETE twice.
To delete all call records, hold down DELETE for about 6 seconds. The module
displays –NOCALLS–.
24
43-962A.fm Page 25 Monday, August 16, 1999 3:33 PM
CARE AND MAINTENANCE
Your RadioShack System 240 60-Number Memory Caller ID is an example of
superior design and craftsmanship. The following suggestions will help you care
for the module so you can enjoy it for years.
Keep the module dry. If it gets wet, wipe it dry immediately. Liq-
uids can contain minerals that corrode electronic circuits.
Use and store the module only in normal temperature environ-
ments. Temperature extremes can shorten the life of electronic
devices, damage batteries, and distort or melt plastic parts.
25
43-962A.fm Page 26 Monday, August 16, 1999 3:33 PM
Handle the module gently and carefully. Dropping it can damage
the circuit boards and can cause the module to work improperly.
Wipe the module with a damp cloth occasionally to keep it look-
ing new. Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the module.
Modifying or tampering with the module’s internal components can cause a mal-
function and might invalidate its warranty and void your FCC authorization to
operate it. If your module is not performing as it should, take it to your local Ra-
dioShack store for assistance. If the trouble is harming the telephone lines, the
telephone company might ask you to disconnect the module until you have re-
solved the problem.
26
43-962A.fm Page 27 Monday, August 16, 1999 3:33 PM
LIGHTNING
This system has built-in protection circuits to reduce the risk of damage from
surges in phone and power line current. These protection circuits meet or ex-
ceed the FCC requirements. However, lightning striking the phone or power
lines can damage the system.
Lightning damage is not common. Nevertheless, if you live in an area that has
severe electrical storms, we suggest that you unplug the module during storms
to reduce the possibility of damage.
27
43-962A.fm Page 28 Monday, August 16, 1999 3:33 PM
NOTES
28
43-962A.fm Page 29 Monday, August 16, 1999 3:33 PM
29
43-962A.fm Page 30 Monday, August 16, 1999 3:33 PM
30
43-962A.fm Page 31 Monday, August 16, 1999 3:33 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship
under normal use for one (1) year from the date of purchase from RadioShack company-owned stores
and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack
MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS
PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUS-
TOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO,
ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVE-
NUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of inci-
dental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales
receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless other-
wise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) re-
place the product with one of the same or similar design; or (c) refund the purchase price. All replaced
(Continued)
31
7
39/
l
Sle
e
W
hta
W
e
c
i
v
Sre
e
W
neud)
otni
C
(
|