[ Quick Start Guide ]
4 0 0 0 S E R I E S A D A P T E R I N S T A L L A T I O N
z
Quick Start Guide
Installation Instructions
This Quick Start Guide describes how to install and configure your new QLogic host bus adapter in four simple steps:
■
■
■
■
Step 1. Verify the package contents.
Step 2. Install the adapter hardware.
Step 3. Install the adapter driver.
Step 4. Install the SANsurfer iSCSI HBA Manager application.
Keep the host bus adapter in the antistatic bag until installation. The host bus adapter contains parts that can be
damagedbyelectrostaticdischarge(ESD). Beforehandlingthehostbusadapter, usestandardmethodstodischarge
static electricity. Place the host bus adapter on the bag when examining it. Retain the bag for future use.
CAUTION!
Step 1. Verify the Package Contents
The QLogic host bus adapter is shipped with the following items:
■
■
QLogic adapter
Low-profile bracket (not available in all models)
Step 2. Install the Adapter Hardware
NOTE:
When installing the QLogic host bus adapter and driver in a Solaris system that does not already have QLogic
adapters or drivers installed, please install the QLogic Solaris driver before you install the QLogic adapter hardware.
This allows Solaris to correctly bind the QLogic Solaris driver to the QLogic adapter. Failure to do so will require an
additional system reboot after the driver is loaded.
To install the adapter hardware, you need to open the computer and locate the appropriate bus slot. If necessary, consult
your computer system manual for instructions to remove the computer cover.
Follow these steps to install the adapter hardware:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Power off the computer and all attached devices such as monitors, printers, and external components.
Disconnect the power cable.
Remove the computer cover and find an empty bus slot.
Pull out the slot cover (if any) by removing the screw or releasing the lever.
Install the low-profile bracket (if required).
Grasp the adapter by the top edge and seat it firmly into the slot (see Figure 1).
Refasten the adapter’s retaining bracket using the existing screw or lever.
Close the computer cover.
Plug in the power cable and turn on the computer.
3
HOST BUS
ADAPTER
LEVER
64-BIT PCI-X SLOT
(QLA405x ADAPTERS) OR
SCREW
PCI EXPRESS x4, x8, x16
SLOT (QLE406xC
ADAPTERS)
ADAPTER RETAINING
BRACKET
SLOT COVERS
SYSTEM
CHASSIS
Figure 1. Illustration of Server Motherboard and Slots
Step 3. Install the Adapter Driver
To install the adapter drivers:
1.
2.
3.
Click QLogic Products.
From the table at the bottom of the page, select iSCSI Adapters, the appropriate adapter model, and
your operating system, and then click Go. The product download page opens.
4.
5.
On the download page under Drivers, select the appropriate driver and download it to your system.
Follow the instructions in the driver readme file for installing the downloaded driver.
Step 4. Install the SANsurfer iSCSI HBA Manager Application
To install the SANsurfer iSCSI HBA Manager application:
1.
2.
3.
Click QLogic Products.
From the table at the bottom of the page, select iSCSI Adapters, the appropriate adapter model, and
your operating system, and then click Go. The product download page opens.
4.
5.
OnthedownloadpageunderManagementTools,selectSANsurferiSCSIHBAManageranddownload
it to your system.
Follow the instructions in the iSCSI HBA Manager readme file for installing the downloaded software.
Additional Resources
■
To obtain the most current drivers, management applications, user instructions, and documentation, please
■
■
For descriptions and procedures related to SANsurfer iSCSI HBA Manager, use the built-in help system.
The following section contains additional information about the QLogic adapter, including the LED scheme,
warranty, and laser safety certification information.
4
Adapter LEDs
Table 1. QLogic QLA4050 Host Bus Adapter LED Scheme
Green LED
Activity
Link established
On
Table 2. QLogic QLA4050C/4052C and QLE4060C/4062C Host Bus Adapter LED Scheme
Green LED
On
Activity
Link established
Receive/transmit activity
Flashing
Warranty
For warranty details, please check the QLogic Web site at http://www.qlogic.com/Support/Pages/Warranty.aspx.
Laser Safety
FDA Notice
This product complies with DHHS Rules 21CFR Chapter I, Subchapter J. This product has been designed and manufactured according to
IEC60825-1 on the safety label of laser product.
Class 1 Laser Product
Appareil laser de classe 1
Produkt der Laser Klasse 1
Luokan 1 Laserlaite
Caution—Class 1 laser radiation when open
Do not view directly with optical instruments
CLASS I LASER
Attention—Radiation laser de classe 1
Ne pas regarder directement avec des instruments optiques
Vorsicht—Laserstrahlung der Klasse 1 bei geöffneter Abdeckung
Direktes Ansehen mit optischen Instrumenten vermeiden
Varoitus—Luokan 1 lasersäteilyä, kun laite on auki
Älä katso suoraan laitteeseen käyttämällä optisia instrumenttej
5
Agency Certification
QLogic Adapters
The following sections contain a summary of EMC/EMI test specifications performed on the QLogic host bus adapters to comply with
radiated emission, radiated immunity, and product safety standards:
EMI and EMC Requirements
FCC Part 15 compliance: Class B
FCC compliance information statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
ICES-003 compliance: Class B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE Mark 89/336/EEC EMC Directive compliance:
EN55022:1998/CISPR22:1997—Class B
EN55024:1998
Immunity Standards
IEC61000-4-2
IEC61000-4-3
IEC61000-4-4
IEC61000-4-5
IEC61000-4-6
IEC61000-4-8
:
:
:
:
:
:
ESD
RF Electro Magnetic Field
Fast Transient/Burst
Fast Surge Common/ Differential
RF Conducted Susceptibility
Power Frequency Magnetic Filed
IEC61000-4-11 : Voltage Dips and Interrupt
IEC61000-3-2
IEC61000-3-3
:
:
Harmonic Current Emission
Voltage Fluctuation and Flicker
VCCI compliance: Class B
AS/NZS CISPR22 compliance: Class B
CNS 13438 compliance: Class B
MIC compliance: Class B
■
Korea MIC Class B Certified
Product Name/Model
Certification holder
iSCSI host bus adapter
QLogic Corporation
Manufactured date
Refer to date code listed on product
QLogic Corporation/USA
Manufacturer/Country of origin
B class equipment
(Household purpose info/telecommunications
equipment)
As this equipment has undergone EMC registration for
household purpose, this product can be used in any area
including residential area.
■
Korean Language Format— Class B
6
Product Safety Compliance
UL, cUL product safety compliance:
UL60950
CSA C22.2 No.60950
Class 1 Laser Product per DHHS 21CFR (J)
Complies with 21 CFR 1040.10 and 1040.11
Use only with listed ITE or equivalent.
73/23/ECC low voltage directive:
TUV:
-EN60950-1:2001
-EN60825-1
-EN60825-2
7
8
9
10
© 2005–2011 QLogic Corporation. QLogic, the QLogic logo, and SANsurfer are trademarks or registered trademarks
of QLogic Corporation. All other brands and product names are trademarks or registered trademarks of their respective
owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no
responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes
in product design or specifications
Corporate Headquarters
International Offices
QLogic Corporation
UK | Ireland | Germany | France
India | Japan | China
Hong Kong | Singapore | Taiwan
26650 Aliso Viejo Parkway
Aliso Viejo, CA 92656
949.389.6000 www.qlogic.com
*IS0054501-00 E*
IS0054501-00 E
|