OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating your set and
retain it for future reference.
LCD MONITOR MODEL
E2241V
E2341
E2341VG
E2441
2541V
V
V
E
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
Leaving a fixed image on the screen for a long time may cause damage to the
screen and cause image burn-in. Make sure to use a screen saver on the product.
Burn-in and related problems are not covered by the warranty on this product.
Do not shock or scratch the front and sides of the screen with metallic objects.
Otherwise, it may cause damage to the screen.
Make sure the panel faces forward and hold it with both hands to move. If you
drop the product, the damaged product can cause electric shock or fire. Contact
an authorized the service center for repair.
Avoid high temperatures and humidity.
For displays with glossy bezels the user should consider the placement of the
display as the bezel may cause disturbing reflections from surrounding light and
bright surfaces.
2
Important Precautions
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene, paint thinners or alcohol)
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;
wipe in one direction only. Too much moisture may cause staining.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
3
Accessories
!!! Thank for selecting LGE products !!!
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Power Cord
User's Guide/Cards
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be
attached to this product before
shipping out.)
DVI-D Signal Cable
(This feature is not available in all
countries.)
NOTE
This accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite
cores to maintain standard compliance for the product.
4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1. Place the monitor with its front facing downward on
a soft cloth.
2. Assemble the Stand Body into the
3. Assemble the Stand Base(Front,
Rear) into the Stand Body in the
correct direction.
product in the correct direction as shown in
the picture. Make sure you push it until you
hear it “click”.
Hinge Body
Stand Body
Stand Body
Stand Base
4. Use a coin on the back of the stand base and turn the screw clockwise to tighten.
5. Once assembled take the monitor up carefully and face the front side
.
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
5
Connecting the Display
Disassembling the stand
2. Place the monitor face Down on the
1. Put a cushion or soft cloth on aflat
cushion or soft cloth.
surface.
3.Remove the Stand Body and
Stand Base from product in
correct direction as shown in the
4. Use a coin on the back of the Stand
Base and turn the screw anticlock-
wise to loosen
.
picture
.
6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off.
Positioning your display
-After installation, adjust the angle as shown below.
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚ to 15˚
Do not touch or press the screen when
adjusting the angle of the monitor.
When adjusting the angle of the screen, do
not put your finger(s) in between the head of
the monitor and the stand body. You can
hurt your finger(s).
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not exceed 5 degrees.
7
Connecting the Display
E2241V/E2341V/E2341VG/E2441V/E2541V
Connecting with the PC
1. Before setting up the monitor, ensure that the power to the monitor, the computer
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd
in order, then tighten the screw
1
2
of the signal cable.
A
C
Connect DVI-D(Digital signal) Cable
Connect D-sub(Analog signal) Cable
Connect HDMI Cable
B
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
When using a D-Sub signal input cable connector
for Macintosh
Mac adapter :For Apple Macintosh use, a
separate plug adapter is needed to change the
15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2
row connector.
Varies according to model.
Connect the signal
input cable and tighten
it up by turning in the
direction of the arrow
as shown in the figure.
AV equipment
Wall-outlet type
(Set-Top Box, DVD, Video,
Video Game Console)
* HDMI is optimized on the AV equipment.
* Not supported PC
Headphone/Speaker
3. Press the power button on the front panel to turn the power on. When monitor power is
turned on, the 'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
Power Button
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals.
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.
8
Control Panel Functions
Front Panel Controls
For D-SUB and DVI input
Only for HDMI input
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
9
Control Panel Functions
Use this button to enter SUPER ENERGY SAVING
menu.For more information, refer to page 15.
SUPER ENERGY
SAVING Button
AUTO Button
(For D-SUB and
DVI input)
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press the
AUTO button on the MONITOR SETUP OSD. (Only
Analog Mode)
This will automatically adjust your display image to the
ideal settings for the current screen resolution size
(display mode).
The best display mode is
E2241V/E2341V/E2341VG/E2441V/E2541V: 1920 x 1080
To adjust the volume of headphone/speaker.
VOLUME Button
(Only for HDMI input)
Use this button to select source from input.
INPUT Button
(SOURCE Hot key)
When two input signals at least are connected, you can
select the input signal (D-SUB/DVI/HDMI) you want. When
only one signal is connected, it is automatically detected.
The default setting is D-Sub.
EXIT Button
Exit the OSD(On Screen Display).
Use this button to turn the display on or off.
Power Button &
Power Indicator
The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode , the
power indicator is blinking blue.
10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating
parameters of the display is quick and easy with the On Screen
Display Control system.
A short example is given below to familiarize you with the use of the
controls. The following section is an outline of the available
adjustments and selections you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the discretionary Button, then the main menu of the OSD appears.
1
To access a control, use the corresponding Buttons.
2
Use the
Use the
/
/
Buttons to adjust the image to the desired level.
3
4
Button to select other sub-menu items.
Press the EXIT Button to exit from the OSD.
11
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
DSUB : D-SUB(Analog signal) input
: DVI-D(Digital signal) input
: HDMI signal
DVI-D
HDMI
Main menu
Sub-menu
BRIGHTNESS
Supported input
Description
To adjust the brightness of the
screen
MENU
DSUB
DVI-D
HDMI
To adjust the image size
ORIGINAL RATIO
To customize the color of the
screen
COLOR TEMP
(PRESET / USER)
To adjust the contrast of the
screen
CONTRAST
To set offset level
HDMI
BLACK LEVEL
LANGUAGE
DSUB
DVI-D
HDMI
To customize the screen status
for a user's operating
environment
FACTORY RESET
SUPER
Turn on the SUPER ENERGY
SAVING function.
DSUB
DVI-D
HDMI
ON
ENERGY
SAVING
Turn off the SUPER ENERGY
SAVING function.
OFF
Initialize the SUPER ENERGY
SAVING and set to "OFF" mode.
RESET
HDMI
VOLUME
NOTE
To adjust the volume
The order of icons may differ depending on the model (12~17).
12
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
To adjust the brightness of the screen.
WIDE
Switch to full screen mode according to
input image signal.
ORIGINAL
Change the input image signal ratio to
original.
* This function works only if input
resolution is lower than monitor ratio
(16:9).
Select the screen color.
PRESET
• WARM: Set the screen to warm color
temperature .
• MEDIUM: Set the screen to medium
color temperature.
• COOL: Set the screen to cool color
temperature.
USER
RED
Exit : Exit
Set your own red color levels.
,
,
: Move
: Select another sub-menu
GREEN
Set your own green color levels.
BLUE
Set your own blue color levels.
13
On Screen Display(OSD) Selection and Adjustment
Main menu
Description
To adjust the contrast of the screen.
(Only HDMI input)
You can set the offset level. If you select
'HIGH', the screen will be bright and if you
select ‘LOW’, the screen will be dark.
(only for HDMI input)
* Offset? As the criteria for video signal, it
is the darkest screen the monitor can
show.
To choose the language in which the
control names are displayed.
Restore all factory default settings except
"LANGUAGE."
Press the
immediately.
,
buttons to reset
Exit : Exit
,
,
: Move
: Select another sub-menu
14
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the SUPER ENERGY SAVING Button, then the main menu of the
OSD appears.
Menu Name
Sub-menus
Icons
Exit
Button
Move
Tip
Restart to select sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
15
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
Turn on the SUPER ENERGY
SAVING fuction.
ON
When current setting value is
ON,the SUPER SAVING color is
green.
OFF
Turn off the SUPER ENERGY
SAVING function.Now the monitor
is LED SAVING function.
When current setting value is
OFF,the SUPER SAVING color is
gray.
Clear the TOTAL POWER
REDUCTION and TOTAL CO2
REDUCTION values.
RESET
Exit : Exit
,
: Move
: Select another sub-menu
OK : Select
TOTAL POWER REDUCTION : How much power is saved during using the monitor.
TOTAL CO2 REDUCTION : Change the TOTAL POWER REDUCTION to CO2.
16
On Screen Display(OSD) Selection and Adjustment
NOTE
SAVING DATA(W/h):
25 inch
22 inch 23 inch 24 inch
5
4
5
5
SUPER SAVING
LED SAVING
12
15
12
17
Saving Data depends on the Panel. So,those values should be different from
each panel and panel vendor.
LG accumulate those values using integrated function with 10 minutes
broadcast video signal.
LED Saving means that how much power can be saved using WLED Panel
instead of CCFL panel.
SUPER Saving means that how much power can be more saved using
SUPER ENERGY SAVING function.
17
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power indicator
Press the Power button.
light on?
G Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
flickering?
• Try to turn on the PC
.
G Do you see an "OUT OF
RANGE" message on
the screen?
•
•
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
G Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
G
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
18
Troubleshooting
Display image is incorrect
G Display Position is
•
Press the AUTO button to automatically adjust
incorrect.
your display image to the ideal setting.
•
Press the AUTO button to automatically adjust
your display image to the ideal setting.
G On the screen
background, vertical
bars or stripes are
visible.
•
•
Press the AUTO button to automatically adjust
your display image to the ideal setting.
G Any horizontal noise
appearing in any
image or characters
are not clearly
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
portrayed.
IMPORTANT
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be
blurred and the screen may be dimmed, truncated or biased. Make sure to select
the recommend resolution.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer.
19
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
G The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA
DDC) monitor found" message?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
The Audio function is not working
G
Picture OK & No sound.
• Check whether volume is "0".
• Check sound muted.
• HDMI cable installed properly.
• Head phone cable installed properly.
• Check sound format. Not supply to compressed
sound format.
20
Specifications
E2241V
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 54.6 cm
0
.248 mm x 0.248 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
30 kHz to 83 kHz (Automatic)
Sync Input
Video Input
Analog,Digital : 56 Hz to 75 Hz (Automatic)
HDMI : 56 Hz to 61 Hz (Automatic)
Separate Sync.
Input Form
Signal Input
Input Form
Digital
15 pin D-Sub Connector
DVI-D Connector (Digital)
HDMI(TYPE-A) Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
Recommend
VESA 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Analog
,
Digital, HDMI)
:
<
<
24 W(Typ.)
0.3 W
0.3 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 50.9 cm ( 19.80 inch )
Height 38.8 cm ( 15.27 inch )
Depth 16.6 cm ( 6.54 inch )
Width 50.9 cm ( 19.80 inch )
Height 32.2 cm ( 12.67 inch )
Depth 5.8 cm ( 2.28 inch )
Weight(excl. packing)
2.9 kg (6.39 lb)
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type
Power cord
NOTE
Information in this document is subject to change without notice.
21
Specifications
E2341V
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 58.4 cm
0
.265 mm x 0.265 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
30 kHz to 83 kHz (Automatic)
Sync Input
Video Input
Analog,Digital : 56 Hz to 75 Hz (Automatic)
HDMI : 56 Hz to 61 Hz (Automatic)
Separate Sync.
Input Form
Signal Input
Input Form
Digital
15 pin D-Sub Connector
DVI-D Connector (Digital)
HDMI(TYPE-A) Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
Recommend
VESA 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Analog
,
Digital, HDMI)
:
<
<
28 W(Typ.)
0.3 W
0.3 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 54.6 cm ( 21.49 inch )
Height 40.7 cm ( 16.02 inch )
Depth 20.2 cm ( 7.95 inch )
Width 54.6 cm ( 21.49 inch )
Height 34.2 cm ( 13.46 inch )
Depth 5.7 cm ( 2.24 inch )
Weight(excl. packing)
3.4 kg ( 7.49 lb )
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type
Power cord
NOTE
Information in this document is subject to change without notice.
22
Specifications
E2341VG
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Glare coating
Display
Visible diagonal size : 58.4 cm
0
.265 mm x 0.265 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
30 kHz to 83 kHz (Automatic)
Sync Input
Video Input
Analog,Digital : 56 Hz to 75 Hz (Automatic)
HDMI : 56 Hz to 61 Hz (Automatic)
Separate Sync.
Input Form
Signal Input
Input Form
Digital
15 pin D-Sub Connector
DVI-D Connector (Digital)
HDMI(TYPE-A) Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
Recommend
VESA 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Analog
,
Digital, HDMI)
:
<
<
28 W(Typ.)
0.3 W
0.3 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 54.6 cm ( 21.49 inch )
Height 40.7 cm ( 16.02 inch )
Depth 20.2 cm ( 7.95 inch )
Width 54.6 cm ( 21.49 inch )
Height 34.2 cm ( 13.46 inch )
Depth 5.7 cm ( 2.24 inch )
Weight(excl. packing)
3.4 kg ( 7.49 lb )
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.0 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type
Power cord
NOTE
Information in this document is subject to change without notice.
23
Specifications
E2441V
60.97 cm (24 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 60.97 cm
0
.277 mm x 0.277 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
30 kHz to 83 kHz (Automatic)
Sync Input
Video Input
Analog,Digital : 56 Hz to 75 Hz (Automatic)
HDMI : 56 Hz to 61 Hz (Automatic)
Separate Sync.
Input Form
Signal Input
Input Form
Digital
15 pin D-Sub Connector
DVI-D Connector (Digital)
HDMI(TYPE-A) Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
Recommend
VESA 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Analog
,
Digital, HDMI)
:
<
<
25 W(Typ.)
0.3 W
0.3 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 56.9 cm ( 22.40 inch )
Height 41.9 cm ( 16.49 inch )
Depth 17.9 cm ( 7.04 inch )
Width 56.9 cm ( 22.40 inch )
Height 35.4 cm ( 13.93 inch )
Depth 5.9 cm ( 2.32 inch )
Weight(excl. packing)
4.0 kg ( 8.81 lb )
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.2 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type
Power cord
NOTE
Information in this document is subject to change without notice.
24
Specifications
E2541V
63.44 cm (25 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size : 63.44 cm
0.288 mm x 0.288 mm (Pixel pitch)
Horizontal Freq.
Vertical Freq.
30 kHz to 83 kHz (Automatic)
Sync Input
Video Input
Analog,Digital : 56 Hz to 75 Hz (Automatic)
HDMI : 56 Hz to 61 Hz (Automatic)
Separate Sync.
Input Form
Signal Input
Input Form
Digital
15 pin D-Sub Connector
DVI-D Connector (Digital)
HDMI(TYPE-A) Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
Recommend
VESA 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Resolution
Plug&Play
DDC 2B(Analog
,
Digital, HDMI)
:
<
<
33 W(Typ.)
0.3 W
0.3 W
On Mode
Power
Consumption
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
& Weight
Width 59.4 cm ( 23.38 inch )
Height 43.4 cm ( 17.08 inch )
Depth 17.9 cm ( 7.04 inch )
Width 59.4 cm ( 23.38 inch )
Height 37.1 cm ( 14.60 inch )
Depth 6.1 cm ( 2.40 inch )
Weight(excl. packing)
4.4 kg ( 9.70 lb )
Tilt : -5˚ to 15˚
Range
AC 100-240 V~ 50 / 60 Hz 1.2 A
Power Input
Operating Conditions
Environment
al Conditions
Temperature
Humidity
10 ˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20 ˚C to 60 ˚C
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type
Power cord
NOTE
Information in this document is subject to change without notice.
25
Specifications
Preset Modes (Resolution)
DSUB/DVI Timing
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
Polarity(H/V)
-/+
-/-
1
2
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
65.290
67.500
720 x 400
640 x 480
70
60
75
60
75
60
75
75
60
75
60
60
-/-
3
640 x 480
+/+
+/+
-/-
+/+
+/+
+/+
+/+
-/+
+/+
4
800 x 600
800 x 600
5
6
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 1080
7
8
9
10
11
*12
*Recommend Mode
HDMI Timing
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
31.50
31.25
37.50
45.00
28.12
33.75
56.25
67.50
480P
576P
720P
720P
1080i
1080i
1080P
1080P
60
50
50
60
50
60
50
60
Indicator
LED Color
MODE
Blue
Blue Blinking
Off
On Mode
Sleep Mode
Off Mode
26
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2. Remove the Stand Body and Stand Base from product in correct direction as shown in
the picture
.
27
Installing the Wall mount plate
3. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount
plate is purchased.
Kensington Security Slot
<Screw Mounting Interface Dimension>
Hole spacing : 75 mm x 75 mm.
Connected to a locking cable that can
be purchased separately at most
computer stores.
NOTE
VESA compatible only with respect to screw mounting interface dimensions and mounting screw
specifications
Please use VESA standard as below.
* 784.8 mm and under (30.9 inch)
- Wall Mount Pad Thickness : 2.6 mm
- Screw : 4.0 mm x Pitch 0.7 mm x Length 10 mm
* 787.4 mm and above (31.0 inch)
- Please use VESA standard wall mount pad and screws.
28
Make sure to read the Safety Precautions
before using the product.
Keep the OWNER’S MANUAL(CD) in an
accessible place for furture reference.
The model and serial number of the SET is
located on the back or one side of the SET.
Record it below should you ever need service.
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency(EPA).
MODEL
SERIAL
As an ENERGY STAR Partner LGE U. S. A.,Inc.
has determined that this product meets the
ENERGY STAR guidelines for energy efficiency.
|