Owner’s Manual
for advanced features
Digital Camera
Model No.
DMC-FH6
DMC-FH4
DMC-S5
DMC-S2
DMC-FH6
DMC-FH4
DMC-S5
DMC-S2
Before connecting, operating or adjusting this product,
please read the instructions completely.
VQT4G44
M1211KZ0
Contents
- 3 -
Before use
■
Camera handling
Keep the camera away from excessive vibration, force,
or pressure.
Avoid using the camera under the following conditions,
●
which may damage the lens, LCD monitor, or camera
body. This may also cause the camera to malfunction or
prevent recording.
• Dropping or hitting the camera against a hard surface
• Sitting down with the camera in your pants pocket or
forcing it into a full bag
• Adding accessories to the camera strap
• Pushing with excessive force on the lens or LCD monitor
The camera is not dust resistant, splash resistant, or
waterproof.
Avoid using the camera in places with excessive dust
or sand, or where water can come into contact with the
camera.
Avoid using the camera under the following conditions,
●
which present a risk that sand, water, or foreign material
may enter the camera through the lens or openings around
buttons. Be especially careful, because these conditions
may damage the camera and such damage may not be
repairable.
• In extremely dusty or sandy places
• In the rain or by the shore, where the camera may be
exposed to water
■
Condensation (When the lens or the LCD monitor is fogged up)
Condensation may occur when the camera is exposed to
●
sudden changes of temperature or humidity. Avoid these
conditions, which may make the lens or LCD monitor dirty,
cause mold, or damage the camera.
If condensation does occur, turn off the camera and wait
●
about two hours before using it. Once the camera adjusts
to the surrounding temperature, the fogging will clear
naturally.
- 4 -
Before use
■
■
■
Always take a test shot first
Before important events when you will use the camera (at weddings, for example),
always take a test shot to make sure that pictures and sound record correctly.
No compensation for missed shots
We cannot compensate for missed shots if technical problems with the camera or card
prevent recording.
Carefully observe copyright laws
Unauthorized use of recordings which contain works with copyright for purposes other
than personal use is prohibited under copyright law. Recording of certain material may
be restricted even for the purpose of personal use.
■
●
Please note that the actual controls and components, menu items, and other
information for your digital camera may differ from those in the illustrations and screens
provided in this manual. When operation or other information is more or less the same
between models, DMC-FH6 is used as examples for the instructions provided in this
manual.
The operations, procedures, or functions that differ among models are indicated
separately, together with the relevant model number.
●
●
(Example)
DMC-FH6
DMC-S2
Recording mode icons
Recording mode:
Available recording modes
Unavailable recording modes
- 5 -
Standard Accessories
Check that all the accessories are supplied before using the camera.
The accessories and their shape will differ depending on the country or area where the
camera was purchased.
●
For details on the accessories, refer to Basic Owner’s Manual.
Battery Pack is indicated as battery pack or battery in the text.
Battery Charger is indicated as battery charger or charger in the text.
SD Memory Card, SDHC Memory Card and SDXC Memory Card are indicated as card
in the text.
●
●
●
Please dispose of all packaging appropriately.
Keep small parts in a safe place out of the reach of children.
●
●
■
Optional accessories
• Cards are optional. You can record or play back pictures on the built-in memory
• If any accessories are lost, customers in the USA and Puerto Rico should contact
Panasonic’s parts department at 1-800-833-9626 and customers in Canada should
contact 1-800-99-LUMIX (1-800-995-8649) for further information about obtaining
replacement parts.
- 6 -
Names and Functions of Main Parts
We recommend using
the supplied hand strap
to avoid dropping the
camera.
3 Lens
4 Lens barrel
9
DMC-FH6
DMC-FH4
DMC-S5
DMC-S2
11 Hand strap eyelet
13
[
/
14 [MENU/SET] button
16 Cursor button
17 Tripod receptacle
18 Speaker
19 DC coupler cover
For dealer display purpose only
• When using an AC adaptor, ensure that the Panasonic DC coupler (for dealer
display purpose only) and AC adaptor (for dealer display purpose only) are used.
- 8 -
Names and Functions of Main Parts
Cursor button
[MENU/SET]
Up cursor button ( )
Left cursor button ( )
Right cursor button ( )
Down cursor button ( )
• Changing information display
In this manual, the button that is used is shaded or indicated by
.
●
The illustrations and screens in this manual may differ from the actual product.
Do not block the microphone when recording motion pictures.
Some tripods or unipods, and some methods of holding the camera may block the
speaker, making it difficult to hear the beep, etc.
●
●
●
- 9 -
Charging battery
Always charge before first use! (battery shipped uncharged)
■
About batteries that you can use with this unit
It has been found that counterfeit battery packs which look very similar to the
genuine products are made available to purchase in some markets. Some of
these battery packs are not adequately protected with internal protection to
meet the requirements of appropriate safety standards. There is a possibility
that these battery packs may lead to fire or explosion. Please be advised that
we are not liable for any accident or failure occurring as a result of use of a
counterfeit battery pack. To ensure that safe products are used we recommend
that a genuine Panasonic battery pack is used.
• Use the dedicated charger and battery.
Insert the battery terminals and attach the battery
to the charger
Connect the charger to the electrical outlet
Plug-in type
Inlet type
●
●
Battery
Charging light
([CHARGE])
On: Charging in progress
(approx. 120 min. if fully
depleted)
• The AC
cable does
not fit
entirely into
the AC input
terminal. A gap will remain.
Off: Charging complete
If light is flashing:
• Charging may take longer
than normal if battery
Charger
(model-specific)
temperature is too high or
too low (charging may not be
completed).
Charge the battery with the charger indoors
(10 °C to 30 °C (50 °F to 86 °F)).
●
• Battery/charger connector is
dirty. Clean with a dry cloth.
Detach the battery after charging is
completed
The battery charger is in the standby condition when the AC power is supplied.
The primary circuit is always “live” as long as the battery charger is connected to
an electrical outlet.
●
- 10 -
Charging battery
Guidelines for number of recordable pictures and operating time
The number of recordable pictures or available operating time may vary according to
surrounding environment and usage conditions. Figures may be reduced if flash, zoom,
or other functions are used frequently, or in colder climates.
DMC-FH6 DMC-FH4
DMC-S5
DMC-S2
Number of recordable pictures (Approx.)
Recording time (Approx.)
280 pictures
140 min.
260 pictures
130 min.
Recording conditions by CIPA standard
• CIPA is an abbreviation of [Camera & Imaging Products Association].
• [Normal Picture] Mode.
●
• Temperature: 23 °C (73.4 °F) / Humidity: 50%RH when LCD monitor is on.
• Using a Panasonic SD Memory Card (32 MB).
• Using the supplied battery.
• Starting recording 30 seconds after the camera is turned on. (When the Optical
Image Stabilizer function is set to [ON].)
• Recording once every 30 seconds with full flash every second recording.
• Perform a zoom operation every recording (W end → T end, or T end → W end)
• Turning the camera off every 10 recordings and leaving it until the temperature of the
battery decreases.
Number reduced if intervals are longer – e.g. to approx. one quarter for 2-minute
intervals under the above conditions.
Playback time (Approx.)
240 min.
The time required for charging varies depending on conditions of battery usage.
Charging takes longer at high or low temperatures and when the battery has not been
used for some time.
●
Battery will be warm during charging and for some time thereafter.
Battery will run out if not used for long periods of time, even after being charged.
We do not recommend frequently charging the battery.
(Frequently charging battery reduces maximum usage time and can cause battery to
expand.)
●
●
●
If available battery power is significantly reduced, battery is reaching end of lifespan.
Please purchase a new battery.
●
- 11 -
Inserting and removing the card (optional)/
the battery
Turn off the power and slide
the card/battery door out ( )
before opening the door ( ) as
illustrated
Insert the battery and card,
making sure that their
orientation is correct
• Battery: Insert all the way firmly until
a locking sound is heard, and
check that the lever is hooked
over the battery.
• Card: Insert all the way firmly until it
clicks.
Card
(check orientation:
terminals face LCD)
Do not touch the terminal
Charged battery (check orientation)
Close the card/battery door and slide the door in until you
hear a locking sound
- 12 -
Inserting and removing the card (optional)/the battery
■
To remove
• To remove battery: Move lever in direction of arrow.
DMC-FH6
DMC-FH4
DMC-S5
DMC-S2
• To remove card: Press down in center.
Always use genuine Panasonic batteries.
If you use other batteries, we cannot guarantee the quality of this product.
Remove battery from camera after use.
• Keep the battery in a plastic bag, making sure that it is kept away from metallic
objects (such as clips) when carrying or storing the battery.
●
●
●
To remove the card or battery, turn the camera off and wait until the LCD monitor
display is completely blank. (Failure to wait may cause the camera to malfunction and
may damage the card or recorded data.)
●
Keep the Memory Card out of reach of children to prevent swallowing.
The unusable battery should be discarded in accordance with battery recycling laws.
Call the RBRC hotline at 1-800-822-8837 for information.
●
●
- 13 -
Inserting and removing the card (optional)/the battery
Picture save destination (cards and built-in memory)
■
Built-in memory (Approx. 70 MB)
The access time for the built-in memory may be longer than the access time for a card.
●
●
■
Compatible memory cards (optional)
The following SD standard-based cards (Panasonic brand recommended)
Type of Card
SD Memory Cards
Capacity
Notes
∗
8 MB – 2 GB
4 GB – 32 GB
48 GB, 64 GB
• Using a card of SD speed “Class 6” or above is
recommended for recording motion pictures.
• Can be used with devices compatible with the
respective formats.
SDHC Memory Cards
SDXC Memory Cards
• Before using SDXC Memory Cards, check that
your computer and other devices support this type
of card.
http://panasonic.net/avc/sdcard/information/SDXC.html
• Only the cards listed on the left with the given
capacities are supported.
∗
SD speed class refers to a specification for sustained write speeds. Confirm the SD speed by
checking the card label or other card related materials.
(Example)
Please reformat the card with this camera if it has already been
If the write-protect switch is set to “LOCK”, the card cannot be used
to record or delete pictures, and it cannot be formatted.
It is recommended that you copy important pictures to your
●
●
●
computer (as electromagnetic waves, static electricity, or faults may
cause data to be damaged).
Switch
Latest information:
http://panasonic.jp/support/global/cs/dsc/ (This Site is English only.)
●
- 14 -
Inserting and removing the card (optional)/the battery
Remaining battery and memory capacity
Remaining battery (only when using battery)
(flashes red)
If the battery mark flashes red, recharge or replace battery.
Estimated remaining pictures or recording time capacity
Displayed when no card is inserted (pictures will be saved to built-in memory)
When in operation
(Card) or
(Built-in memory) are illuminated red.
While the light remains lit, an operation is taking place, such as picture writing or reading.
While the light is lit, do not turn off the power or remove battery, card, AC adaptor (for
dealer display purpose only) or DC coupler (for dealer display purpose only), as this can
cause data loss or damage. Do not subject the camera to vibrations, impact, or static
electricity. Should any of these cause camera operation to be terminated, attempt to
perform the operation again.
Recording capacity guidelines (pictures/recording time)
The number of pictures you can take and the recording time vary in proportion to card
capacity (and depending on recording conditions and type of card).
If you make Web upload settings, the recording picture capacity and the recording time
capacity of the card may be reduced.
●
■
Recording picture capacity (still pictures)
[Picture Size]
Built-in memory
2 GB
300
32 GB
4910
64 GB
9880
1
∗
11
16M
2
∗
12
25
330
650
5490
10620
162960
10980
21490
14M
5M
0.3M
390
10050
247160
• When the number of recordable pictures exceeds 99,999, “+99999” is displayed.
■
Recording time capacity (motion pictures)
[Rec Quality]
Built-in memory
2 GB
10m10s
8m10s
21m40s
1h02m00s
32 GB
64 GB
1
∗
–
–
–
2h47m00s
2h14m00s
5h54m00s
16h59m00s
5h39m00s
4h32m00s
11h56m00s
34h21m00s
HD
HD
VGA
2
∗
QVGA
2m25s
([h], [m] and [s] indicate “hour”, “minute” and “second”.)
• Motion pictures can be recorded continuously up to 2 GB.
The maximum available recording time for up to 2 GB only is displayed on the screen.
1 DMC-S5
∗
2 DMC-FH6, DMC-FH4, DMC-S2
∗
- 15 -
Setting the clock
The clock is not set when the camera is shipped.
Press the Power button
The power is turned on.
If the language select screen is not displayed,
proceed to step
.
Press [MENU/SET] while the
message is displayed
Press
to select the language,
and press [MENU/SET]
• The [Please set the clock] message
appears.
Press [MENU/SET]
Press
to select the items
(year, month, day, hour, minute,
display order or time display
format), and press
to set
• To cancel → Press [
/
] button.
Press [MENU/SET]
Press [MENU/SET]
• To return to the previous screen,
press [ ] button.
/
If the clock is not set, the correct date cannot be printed when you order a photo studio
to print the picture, or when you stamp the date on the pictures with [Date Stamp].
If the clock is set, the correct date can be printed even if the date is not displayed on
the screen of the camera.
●
●
- 16 -
Setting the clock
To change time setting
When resetting date and time, select [Clock Set] from the [Setup] menu.
• Clock settings will be saved for approx. 3 months even after battery is removed,
provided a fully-charged battery was installed in the camera for 24 hours beforehand.
Set the date and time
• Press
to select the items (year, month, day, hour, minute, display order or
to set.
time display format), and press
To cancel → Press [
/
] button.
- 17 -
Sequence of operations
Press the Power button
Press [MODE] button
Use cursor button to select the
recording mode and press
[MENU/SET]
■
■
Recording mode
Take pictures with automatic settings.
Take pictures with your own settings.
Take pictures according to scene.
Take motion pictures.
Press [MENU/SET]
Use cursor button and [MENU/SET] to select the menu
Press [
/
] button
- 18 -
Sequence of operations
Flash
Holding the camera
Microphone
• To avoid camera shake, hold it with both
hands keeping your arms close to your body
and standing with your feet slightly apart.
• Do not touch the lens.
• Do not block the flash or the AF Assist
Lamp. Do not look at it from close range.
• Try to hold the camera steady when you
press the shutter button.
• Be careful not to block the microphone or
the speaker.
Speaker
AF Assist Lamp
■
Zoom In/Out
DMC-FH6
We recommend using the
supplied hand strap to avoid
dropping the camera.
Capture a
wider area
Enlarge
the subject
(telephoto)
(wide-angle)
DMC-FH4
DMC-S5
DMC-S2
Capture a
wider area
(wide-angle)
Enlarge
the subject
(telephoto)
■
Flash, self-timer, and other functions
Exposure
Compensation
Self-timer
Flash
Changing
information
display
- 19 -
Sequence of operations
Press the shutter button and take
pictures
Press halfway
(press lightly to focus)
Press fully
(press the button all the
way to record)
• For motion pictures, recording will start.
To end recording, press the shutter
button again.
Press the Playback button
Press [MODE] button
Use cursor button to select playback
mode and press [MENU/SET]
■
Playback mode
Displays all pictures that can be played back.
Automatically plays back the still pictures in order, in parallel with music.
Only pictures in selected categories and pictures set as favorite are
displayed.
Pictures recorded on the date selected on the calendar screen can be
displayed.
- 20 -
Sequence of operations
Use cursor button to select a
picture to be played back
• Play back motion pictures or
panorama pictures
• [Auto Retouch]
• [Beauty Retouch]
DMC-FH6
Previous
Next
Changing
information
display
• Editing or performing settings for
Press the Power button
- 21 -
Taking pictures with automatic settings
[Intelligent Auto] Mode
Recording mode:
Optimum settings are made automatically from information such as “face”, “movement”,
“brightness”, and “distance” just by pointing the camera at the subject, meaning that clear
pictures can be taken without the need to make settings manually.
Shutter button
Display the screen for recording
mode selection
Select
[Intelligent Auto] Mode
Focus display
(When focus is aligned: illuminated
When focus is not aligned: flashing)
Take pictures
Press halfway
(press lightly to focus)
Press fully
(press the button all the
way to record)
- 22 -
Taking pictures with automatic settings [Intelligent Auto] Mode
Automatic Scene Detection
Camera reads scene when pointed at subject, and makes optimum settings automatically.
Recognizes people
Recognizes landscapes
Recognizes night scenes and people in them
∗
is selected)
Recognizes night scenes
Recognizes close-ups
Recognizes sunsets
(Only when
∗
Reads subject movement to avoid blurring when scene
does not correspond to any of the above.
We recommend using a tripod and the self-timer.
The icon of scene detected
∗
Depending on recording conditions, different scene types may be determined for the
same subject.
If desired scene type is not selected, we recommend manually selecting the appropriate
recording mode.
●
●
●
●
When
or
is detected, Face Detection is activated, and the focus and exposure
are adjusted for the recognized faces.
About Backlight Compensation
Backlight is a condition where a light shines from behind a subject. When there is a
backlight, a subject appears darker and the camera automatically corrects the exposure
by increasing the brightness of an entire image. When the camera detects backlight,
is displayed on the LCD monitor.
About flash
Press to select
or
is selected, the optimum flash is selected automatically depending on
.
When
●
When
When
or
or
is selected, the red-eye reduction function is activated.
is selected, the shutter speed is reduced.
●
●
About the Happy color setting
■
Settings:
Press [MENU/SET]
Press
Press
Press
to select [Rec] menu and press [MENU/SET]
to select [Color Mode] and press [MENU/SET]
to select [Happy] and press [MENU/SET]
- 23 -
Taking pictures with automatic settings [Intelligent Auto] Mode
Notes on setting items
Only menu items which are displayed in the [Intelligent Auto] Mode can be set.
The settings selected in the [Normal Picture] Mode or other modes are reflected for not
displayed menu items on the [Setup] menu.
The settings for the following items are different from other recording modes:
●
DMC-FH6
[Picture Size], [Color Mode] and [Burst]
The settings for the following functions are fixed:
on the [Rec] menu
●
DMC-FH6
• [Auto Review]: [2 SEC.]
DMC-FH4
DMC-S5
DMC-S2
[ON]
• [Stabilizer]: [ON]
• [AF Assist Lamp]: [ON]
• [i.Resolution]: [i.ZOOM]
• [Sensitivity]:
• [AF Mode]:
• [i.Exposure]: [ON]
∗
(Face Detection)
• [Auto Power Off]: [5 MIN.]
• [White Balance]: [AWB]
(23-area-focusing) when face cannot be recognized
The following functions cannot be used:
[Exposure], [Digital Zoom]
• [Red-Eye Removal]: [ON]
∗
●
- 24 -
Taking motion pictures [Motion Picture] Mode
Recording mode:
Display the screen for recording
mode selection
Microphone
(Do not block the microphone
with your fingers)
Select
[Motion Picture] Mode
Start recording
Press halfway
(adjust the focus)
Press fully
(start recording)
• Immediately release the shutter button after
pressing it all the way.
Remaining recording time (approx.)
• The focus and zoom will remain as they
were at the beginning of recording.
End recording
Elapsed recording time
Press fully
Depending on the type of card used, a card-access display may appear for a while after
motion picture recording. This is not a fault.
●
In [AF Mode],
In [Stabilizer], [ON] is fixed.
When there is no space left to store the motion picture, recording automatically ends.
Additionally, recording in progress may be stopped, depending on the card used.
(23-area-focusing) is fixed.
●
●
●
- 25 -
Viewing your pictures
[Normal Play]
When a card is in the camera, pictures are played back from the card, and without a card,
pictures are played back from the built-in memory.
Press the Playback button
• Press again to enter the
recording mode.
Scroll through pictures
Previous Next
File number
Picture number/Total pictures
• Hold down to quickly scroll forwards/
backwards.
• Press the shutter button to switch to
recording mode.
■
Changing recording information display
Press
.
It may not be possible to view pictures on this camera that were previously edited on a
computer.
After pressing the Playback button and switching it into the playback mode, the lens
barrel will be retracted after approx. 15 seconds.
This camera is compliant with the unified DCF (Design rule for Camera File system)
standard formulated by the Japan Electronics and Information Technology Industries
Association (JEITA), and with Exif (Exchangeable image file format). Files that are not
DCF-compliant cannot be played back.
●
●
●
- 26 -
Viewing your pictures [Normal Play]
Viewing motion pictures
Select a picture with the motion picture icon, and press
Playback now starts.
Motion picture recording time
When playback starts, the elapsed playback time is displayed
in the top right of the screen.
Example: After 3 minutes and 30 seconds: [3m30s]
Motion picture icon
■
Operations during motion picture playback
Pause/play
Fast rewind (2 steps)
Single-frame rewind (while paused)
Fast forward (2 steps)
Single-frame forward (while paused)
Stop
Volume can be adjusted with the zoom lever or the zoom button.
●
It may not be possible to properly play back motion pictures recorded using other
cameras.
Motion pictures can be viewed on your computer using “PHOTOfunSTUDIO” on the
supplied CD-ROM.
Be careful not to block the speaker.
●
●
●
Speaker
- 27 -
Viewing your pictures [Normal Play]
Zooming in and viewing “Playback Zoom”
DMC-FH6
DMC-FH4
Turn the zoom lever to T side
DMC-S5 DMC-S2
Press the T side of the zoom
button
Current zoom position (displayed for 1 sec.)
1x
2x
4x
8x
16x
DMC-FH6
Turn the zoom lever to T side/
DMC-FH4
DMC-S5
DMC-S2
Press the T side of the zoom button
DMC-FH6
DMC-FH4
Turn the zoom lever to W side/
DMC-S5
DMC-S2
Press the W side of the zoom button
• Move zoom position → Use cursor button to move the zoom position
Playback zoom cannot be used during motion picture playback.
●
- 28 -
Viewing your pictures [Normal Play]
Viewing a list of pictures “Multi Playback”
DMC-FH6
DMC-FH4
Picture no./Total no.
Turn the zoom lever to W side
DMC-S5 DMC-S2
Motion pictures
Panorama pictures
Press the W side of the zoom
button
1-picture
screen
12-picture
screen
30-picture
screen
Calendar
Playback
DMC-FH6
Turn the zoom lever to W side/
DMC-FH4
DMC-S5
DMC-S2
Press the W side of the zoom button
DMC-FH6
DMC-FH4
Turn the zoom lever to T side/
DMC-S5
DMC-S2
Press the T side of the zoom button
• When you select a picture using the cursor button and press [MENU/SET] on the
12-picture or 30-picture screen, the selected picture is displayed on the 1-picture
screen (full-screen).
Pictures displayed with [!] cannot be played back.
●
- 29 -
Viewing your pictures [Normal Play]
Viewing pictures by their recording date “Calendar Playback”
DMC-FH6
Selected date (First picture from the date)
Turn the zoom lever to W
several times
DMC-FH4
DMC-S5
DMC-S2
Press the W side of the zoom
button several times
1-picture
screen
12-picture
screen
30-picture
screen
Calendar
Playback
DMC-FH6
Turn the zoom lever to W side/
DMC-FH4
DMC-S5
DMC-S2
Press the W side of the zoom button
DMC-FH6
DMC-FH4
Turn the zoom lever to T side/
DMC-S5
DMC-S2
Press the T side of the zoom button
• When you select a recording date using the cursor button and press [MENU/SET], the
display method changes to the 12-picture screen.
Only months when pictures were taken are shown on the calendar screen. Pictures
●
taken without clock settings are displayed with the date January 1, 2012.
Pictures taken with destination settings made in [World Time] are displayed in the
calendar screen using the appropriate date for the destination’s time zone.
●
- 30 -
Deleting pictures
Pictures will be deleted from the card if the card is inserted, or from the built-in memory if
the card is not inserted. (Deleted pictures cannot be recovered.)
Press to delete displayed picture
• A confirmation screen is displayed. Select [Yes]
with cursor button and then press [MENU/SET].
Do not turn off the power during deletion.
Use a sufficiently charged battery.
Pictures cannot be deleted in the following cases:
• Protected pictures
●
●
●
• Card switch is in “LOCK” position.
- 31 -
Deleting pictures
To delete multiple (up to 50)/To delete all pictures
Press to delete displayed picture
Select [Delete Multi]/[Delete All]
[Delete Multi]
Use cursor button to select picture and press
[MENU/SET].
●
• To cancel → Press [MENU/SET] again.
Use cursor button to select [OK] and press
[MENU/SET].
Picture selected
• You can select [All Delete Except Favorite] in
[Delete All] if there are pictures that have been
• A confirmation screen is displayed. Select [Yes]
with cursor button and then press [MENU/SET].
• May take time depending on number of pictures
deleted.
- 32 -
Setting the menu
Refer to the procedure below for an example on how to operate the menus.
Example: Changing [AF Mode] in the [Rec] menu in [Normal Picture] Mode
Press [MENU/SET]
The menu selection screen is displayed.
Select [Rec] menu and press [MENU/SET]
Press
Press
to select [AF Mode] and press [MENU/SET]
Pages
The pages can also be selected with the zoom lever or the
zoom button.
to select a setting, and then press [MENU/SET]
The selected setting is set.
• To cancel → Press [
/
] button.
Settings
Selected setting
Press [
/
] button several times
The menu closes and the monitor returns to the previous screen.
- 33 -
Setting the menu
The operation screen examples in this manual may differ from the actual screen display
or some parts of the screen display are omitted.
●
The menu types and items that are displayed vary according to the mode.
The setting methods vary depending on the menu item.
In recording mode, the menu screen can also be exited by pressing the shutter button
halfway.
●
●
●
Menu type
[Rec] menu (In recording mode only)
• Enables you to set the coloring, picture size, and other items.
[Setup] menu
• Enables you to specify clock settings, sound volume, and so on to make the camera
easier to use.
[Playback] menu (In playback mode only)
• Enables you to specify picture protection, resizing, and other settings for pictures you
have taken.
- 34 -
Using the [Setup] menu
[Clock Set], [Auto Power Off] and [Auto Review] are important for clock setting and
battery life. Please check these before use.
Item
Settings, notes
Set time, date, and display format.
[Clock Set]
Message will be displayed when setting for the first time. In
[World Time]
this case, press [MENU/SET] and skip to step
.
Set the local time at
travel destination.
Use cursor button to select [Home] or [Destination] and
press [MENU/SET]
Use cursor button to select area and press
[MENU/SET]
Current time at
selected destination
City/area name
Difference with
home time
When [Destination] has been selected
■
To set summer time
Press in step . (Press again to release the setting)
• If you cannot find your destination in the area displayed
on the screen, set based on difference with home time.
•
is displayed on the screen for pictures recorded at
the destination when they are played back.
• When summer time is set, the current time is advanced
by 1 hour. If the setting is canceled, the time
automatically returns to the current time.
- 35 -
Using the [Setup] menu
Item Settings, notes
[Beep Level]
: Low / High / Mute
[Beep Tone]
: Change beep tone.
[Shutter Vol.]
: Low / High / Mute
[Shutter Tone]
DMC-FH6
[Beep]
/
/
Change or mute the
beep/shutter sounds.
/
/
/
/
/
/
: Change shutter tone.
: Low / High / Mute
DMC-FH4
DMC-S2
DMC-S5
/
/
[Beep]
Adjust volume of beep
sounds.
[0] / [1] / [2] / [3] / [4] / [5] / [6]
[Volume]
• Cannot be used to adjust TV speaker volume when
connected to TV.
Adjust volume of sound
from speakers (7 levels).
Press
make adjustments
Press [MENU/SET]
to select the setting item and press
to
[LCD Display]
Adjust brightness and
color of the LCD monitor.
• Some subjects may look different from their actual
appearance, but the recorded picture will not be affected.
- 36 -
Using the [Setup] menu
Item
Settings, notes
[Focus Icon]
/
/
/
/
/
Change the focus icon.
[2 MIN.] / [5 MIN.] / [10 MIN.] / [OFF]
[Auto Power Off]
• To restore → Press the Power button
Turn off the power when
you are not using the
camera to minimize
battery consumption.
• Cannot be used in the following cases:
When connected to computer/printer, during motion
picture recording/playback, during Slide Shows, during
automatic demo playback
• Settings fixed to [5 MIN.] in [Intelligent Auto] Mode.
DMC-FH6
[Auto Review]
[1 SEC.] / [2 SEC.]
[HOLD]: Auto review screen remains until a button (other
Automatically display
still pictures immediately
after taking them.
than ) is pressed
[OFF]
DMC-FH4
DMC-S5
DMC-S2
[ON] / [OFF]
• Settings fixed to [2 SEC.] in [Intelligent Auto] Mode.
DMC-FH6
• Settings fixed to [ON] in [Intelligent Auto] Mode.
DMC-FH4
DMC-S5
DMC-S2
• In [Panorama Shot] and [Photo Frame] Scene Modes,
or in [Burst] Mode, Auto Review performed regardless of
setting.
• Motion pictures cannot be automatically reviewed.
[Reset Rec. settings?]
[Reset]
[Reset setup parameters?]
Reset to the default
settings.
• When the setup parameters settings are reset, [Age] for
[Baby] and [Pet] Scene Modes are also reset.
• Folder numbers and clock settings will not be reset.
• Camera movement may be audible as the lens function
is reset. This is not a fault.
- 37 -
Using the [Setup] menu
Item
[Output]
Settings, notes
[Video Out]
(DMC-FH6PU/DMC-FH4PU/DMC-S5PU/DMC-S2PU/
DMC-FH6PR/DMC-FH4PR/DMC-S5PR only)
Adjust the settings used
when the camera is
connected to a TV, etc.
via the AV cable.
[NTSC] / [PAL]
(Playback mode only.)
[TV Aspect]
/
:Rotate and display pictures displayed on a TV
screen as well as those displayed on the LCD
monitor of the camera in portrait orientation.
Rotate and display only pictures displayed on a TV
screen in portrait orientation.
[Rotate Disp.]
Automatically rotate
portrait still pictures.
:
[OFF]
• [Rotate Disp.] cannot be used with motion pictures.
• Still pictures taken with the lens surface facing up or
down, or still pictures taken on other cameras may not
rotate.
• Pictures cannot be rotated during Multi Playback.
• Will only be displayed rotated on computer if in Exif-
Current version is displayed.
[Version Disp.]
Check the version of the
camera firmware.
- 38 -
Using the [Setup] menu
Item
[Format]
Settings, notes
• This requires a sufficiently charged battery. When
formatting the built-in memory, remove the cards.
(Only inserted card will be formatted if present; built-in
memory will be formatted if no card is inserted.)
• Always format cards with this camera.
• All protected pictures and other picture data will be
deleted.
Use when [Built-In
Memory Error] or
[Memory Card Error]
appears, or when
formatting the built-in
memory or card.
• Do not turn off power or perform other operations during
formatting.
When a card/built-in
memory is formatted,
the data cannot be
restored. Check the
content of the card/
built-in memory
• Formatting the built-in memory may take several
minutes.
• If the card cannot be formatted, please try another card
before contacting your nearest Service Center.
For USA and Puerto Rico assistance, please call:
1-800-211-PANA(7262) or, contact us via the web at:
http:www.panasonic.com/contactinfo
carefully before
formatting.
For Canadian assistance, please call:
1-800-99-LUMIX (1-800-995-8649) or
send e-mail to: [email protected]
Set the language displayed on the screen.
[Language]
Change display
language.
[Stabilizer Demo.]
[Demo Mode]
Extent of jitter is shown on graph (estimate)
View demonstration of
functions.
Extent of jitter
Extent of jitter after correction
• During demo screen display, the Optical Image Stabilizer
switches ON and OFF every time [MENU/SET] is
pressed.
[Auto Demo]: View introductory Slide Show
[ON] / [OFF]
• [Auto Demo] cannot be displayed on external devices
such as TVs.
- 39 -
Taking pictures with your own settings
[Normal Picture] Mode
Recording mode:
Using the [Rec] menu to change settings and set up your own recording environment.
Display the screen for recording
mode selection
Shutter button
Select
[Normal Picture] Mode
Take a picture
Press halfway
(press lightly to
focus)
Press fully
(press the button all
the way to record)
■
Changing recording information display
Press
.
If a warning is displayed about jitter, use [Stabilizer], a
tripod, or [Selftimer].
If aperture and shutter speed are shown in red, you do
not have appropriate exposure. Either use the flash or
change the “ISO Sensitivity” settings.
●
●
Jitter alert
display
Aperture value Shutter speed
- 40 -
How to adjust focus
Useful when subject is not in center of picture.
First adjust focus according to subject
Align the AF area
with the subject
Focus display
(When focus is aligned: illuminated
When focus is not aligned: flashing)
AF area
(When focus is aligned: green
When focus is not aligned: red)
Hold down
halfway
Return to desired composition
Subjects/environments which may
make focusing difficult:
●
• Fast-moving or extremely bright
objects, or objects with no color
contrast.
• Taking pictures through glass or
near objects emitting light. In dark,
or with significant jitter.
Press fully
AF area
• When too close to object or when
taking pictures of both distant and
close objects together in the same
picture.
- 41 -
How to adjust focus
■
Focus range
Zoom position
The shortest focusing distance
from the surface of the lens
W end
T end
5 cm (0.16 feet)
1 m (3.3 feet)
∗
When the zoom is operated from the W (wide-angle) end to the T (telephoto) end, the shortest
focusing distance changes in stages.
Focus display
The focus display flashes and beep sounds when focus is not
aligned.
Use the focus range displayed in red as a reference.
Even if the focus display is lit, the camera may be unable to bring
the subject into focus if it is out of range.
●
●
The AF area display size may increase when adjusting the focus
when it is dark and depending on the zoom ratio used.
Focus range
- 42 -
Using zoom
Recording mode:
You can adjust the area of a picture to be taken using zoom.
DMC-FH6
Capture a wider area
(wide-angle)
Enlarge the subject
(telephoto)
DMC-FH4
DMC-S5
DMC-S2
Capture a wider area
(wide-angle)
Enlarge the subject
(telephoto)
When Extended Optical Zoom is set
Optical Zoom range
Focus range
3.3ft
-
∞
Zoom ratio
5X
Digital Zoom range
i.Zoom range
Zoom bar
Adjust the focus after adjusting the zoom.
Do not touch the lens barrel during zooming.
The zoom ratio and the zoom bar displayed on the screen are estimates.
The camera may make a rattling noise and vibrate when the zoom lever or the zoom
button is operated - this is not a fault.
●
●
●
●
- 43 -
Using zoom
Zoom types and use
■
Optical Zoom
Zooming in up to 5 times
possible if pictures without
DMC-FH6
DMC-FH4
DMC-S5
DMC-S2
/4 times
is
have been selected by [Picture Size] on the [Rec] menu.
Optical Zoom cannot be used in [Panorama Shot] Scene Mode.
●
■
Extended Optical Zoom
When you select a picture size with
for [Picture Size] on the [Rec] menu, you can
zoom pictures to a higher zoom ratio with no deterioration in picture quality. The zoom
ratio changes in accordance with the picture size setting. EZ is short for “Extended
Optical Zoom.”
Extended Optical Zoom cannot be used in the following cases:
• [Motion Picture] Mode
●
• Scene Modes ([Panorama Shot] [High Sens.] and [Photo Frame])
• When the [Burst] setting is set to
or
DMC-FH6
To increase the zoom ratio further, the following zoom can be used in combination.
■
i.Zoom
You can use the camera’s super resolution technology to increase the zoom ratio up
to 2 times higher than the original zoom ratio while preventing deterioration of picture
When [i.Resolution] is set to [i.ZOOM], super resolution technology is applied to the
picture.
●
[i.ZOOM] cannot be used in the following cases:
• [Motion Picture] Mode
●
• Scene Modes ([Panorama Shot] and [High Sens.])
• When the [Burst] setting is set to
or
DMC-FH6
■
Digital Zoom
Zoom 4 times further than Optical/Extended Optical Zoom. Note that, with Digital Zoom,
enlarging will decrease picture quality. Set the [Digital Zoom] in the [Rec] menu to [ON].
Digital Zoom cannot be used in the following modes:
• [Intelligent Auto] Mode
●
• Scene Modes ([Panorama Shot] [High Sens.] and [Photo Frame])
• When the [Burst] setting is set to
or
DMC-FH6
• When Digital Zoom is used simultaneously with i.Zoom, you can only increase the
zoom ratio up to 2 times.
- 44 -
Taking pictures with flash
Recording mode:
Press to display [Flash]
Use cursor button to select the desired type and press
[MENU/SET]
Type, operations
Uses
[Auto]
• Automatically judges whether or not to flash
[Auto/Red-Eye]
• Automatically judges whether or not to flash
(reduce red-eye)
Normal use
∗
Taking pictures of subjects in dark
places
[Forced Flash On]
• Always flash
[Slow Sync./Red-Eye]
• Automatically judges whether or not to flash
(reduce red-eye; slow shutter speed to take
brighter pictures)
Taking pictures with backlight or
under bright lighting (e.g. fluorescent)
∗
Taking pictures of subjects against a
nightscape (tripod recommended)
[Forced Flash Off]
• Never flash
Places where flash use is prohibited
∗
Two flashes will be emitted. Do not move until after the second flash. Interval between flashes varies
according to brightness of subject.
If [Red-Eye Removal] on the [Rec] menu is [ON], the
is automatically detected and still picture data is corrected. (Only when [AF Mode] is
Detection))
appears with the flash icon, red-eye
(Face
The effect of red-eye reduction varies depending on the subject and is affected by
factors such as distance to the subject, whether the subject is looking at the camera
during preliminary flash, and so on. In some cases, the effect of red-eye reduction may
be negligible.
Do not put your hands over the light-emitting area of the flash
or look at it from close range (a few centimeters away).
Do not use the flash at close distances to other subjects (heat/
light may damage subject).
●
●
Flash settings may be changed when changing recording mode.
Scene Mode flash settings are restored to default when Scene Mode
is changed.
●
●
No pictures may be taken if these marks (e.g.
(flash is charging).
If light from the flash on a subject is insufficient, neither the proper exposure nor White
Balance is not achieved.
The flash effect may not be sufficient in the following cases:
• Slow shutter speed
) are flashing
●
●
●
Flash
DMC-FH6
• [Flash Burst] is set
Flash charging may take time if battery is low, or if using flash repeatedly.
●
- 45 -
Taking pictures with flash
Available types in each mode (○: Available, –: Not available, : Default setting)
■
[Scene Mode]
1
∗
○
○
○
–
○
○
○
○
–
○
○
○
○
–
○
○
–
○
–
○
○
–
○
–
○
○
○
○
–
○
○
–
○
–
○
○
–
○
–
○
○
○
○
–
○
○
–
–
–
○
○
–
–
–
○
1 Set to
∗
,
,
or
depending on the subject and brightness.
• The flash cannot be used when recording motion pictures or Scene Modes
or
,
,
,
.
■
■
The available flash range when [Sensitivity] setting is [
]
DMC-FH6
Max. W
Max. T
Approx. 40 cm-4.1 m (1.3 feet-13 feet)
Approx. 1.0 m-1.6 m (3.3 feet-5.2 feet)
DMC-FH4
DMC-S5
DMC-S2
Max. W
Max. T
Approx. 40 cm-3.3 m (1.3 feet-11 feet)
Approx. 1.0 m-1.6 m (3.3 feet-5.2 feet)
Shutter speeds for each flash mode
1/60 - 1/1600th
1/8 2 - 1/1600th
∗
2 Max. 1/4 sec. when [
] in [Sensitivity] is set; max. 1 sec. when [Stabilizer] is set to [OFF] or
∗
when blur is insignificant. Also varies according to [Intelligent Auto] Mode and Scene Modes, etc.
- 46 -
Taking pictures with self-timer
Recording mode:
We recommend using a tripod. This is also effective for correcting jitter when pressing the
shutter button, by setting the self-timer to 2 seconds.
Press to display [Selftimer]
Use cursor button to select time duration and press
[MENU/SET]
Take a picture
Press the shutter button fully to start recording after the preset time.
Self-timer indicator
(Flashes for set duration)
• To cancel while in operation → Press [MENU/SET]
Focus will be automatically adjusted immediately before recording if shutter button is
pressed fully here.
●
After Self-timer indicator stops flashing, it may then be lit for AF Assist Lamp.
●
- 47 -
Taking pictures with Exposure Compensation
Recording mode:
Corrects exposure when adequate exposure cannot be obtained (if difference between
brightness of object and background, etc.).
Press to display [Exposure]
Use cursor button to select a value and press [MENU/SET]
• If the picture is too dark, adjust the exposure to the “+”
direction.
• If the picture is too bright, adjust the exposure to the “-”
direction.
• After exposure adjustment, the adjustment value (
for example) is displayed in the bottom-left corner of the
screen.
No compensation: ±0
• The Exposure Compensation value you set is retained
even after the camera is turned off.
Depending on the brightness, this may not be possible in some cases.
●
- 48 -
Taking pictures according to the scene
[Scene Mode]
Recording mode:
Using [Scene Mode] enables you to take pictures with optimum settings (exposure,
coloring, etc.) for given scenes.
Display the screen for recording
mode selection
Select
[Scene Mode]
Select and set the scene
Scene menu
●
Selecting a Scene Mode inappropriate for the actual scene may affect the coloring of
your picture.
Following [Rec] menu settings will be automatically adjusted and cannot be selected
manually.
●
●
[Sensitivity], [i.Exposure], [i.Resolution], [Color Mode]
●
- 49 -
Taking pictures according to the scene [Scene Mode]
Improves the skin tone of subjects for a healthier appearance in bright
daylight conditions.
Tips
[Portrait]
• The closer the zoom is positioned to the T (telephoto) edge and the closer the
camera is brought to the subject, the greater the effect will be.
Smooths skin colors in bright, outdoor daylight conditions (portraits from
chest upwards).
Tips
[Soft Skin]
[Scenery]
• The closer the zoom is positioned to the T (telephoto) edge and the closer the
camera is brought to the subject, the greater the effect will be.
Takes clear pictures of wide, distant subjects.
- 50 -
Taking pictures according to the scene [Scene Mode]
Creates a single panorama picture by stitching multiple still pictures taken
in rapid succession.
Use cursor button to select the recording direction, and press [MENU/SET] to
set.
Check the recording direction and press [MENU/SET]
Special panorama guidelines will be displayed during recording.
Press the shutter button halfway to focus
Press the shutter button fully and pan the camera in a small circular motion in
the selected direction to start recording
• Taking pictures from left to right
2 sec.
Pan the camera at a speed
that turning halfway around in
approx. 4 seconds
1 sec.
3 sec.
• Pan the camera at a constant
speed.
• You may not be able to take
pictures successfully if you
move the camera too quickly
or too slowly.
Pan the
[Panorama
Shot]
camera in a
small circular
motion
Press the shutter button fully again to end recording
• You can also end the recording if you stop panning the camera while taking
pictures.
Tips
• Pan the camera in the recording direction as steadily as possible.
If the camera shakes too
much, it may not be able to
take pictures or may end up
creating a narrow (small)
panorama picture.
The subjects that are displayed in this range are recorded. (guideline)
- 51 -
Taking pictures according to the scene [Scene Mode]
Notes
• The zoom position is fixed to the W end.
• Since the focus, White Balance, and Exposure Compensation are all fixed
when settings are made for the first picture, recording settings such as
brightness and color may not be optimal for subsequent pictures.
• The following functions are fixed to the settings indicated below.
[Stabilizer]: [OFF] [Date Stamp]: [OFF]
• For some subjects, the recorded pictures may be distorted or the joined
sections of multiple successively taken pictures that are stitched may be also
noticeable.
• Picture size varies depending on the recording direction and number of
stitched pictures.
The maximum number of recording pixels is as follows:
- Taking pictures in landscape orientation: Approx. 2M (3200×720)
- Taking pictures in portrait orientation: Approx. 3M (960×3200)
• Panorama pictures may not be created or pictures may not be recorded
properly when taking pictures of the following subjects or when taking pictures
in the following recording conditions:
- Subjects that have a continuous monotone or pattern (sky, beach, etc.)
- Moving subjects (person, pet, vehicle, waves, or flowers swaying in the wind,
etc.)
[Panorama
Shot]
(Continued)
- Subjects whose colors or patterns change quickly (large displays, etc.)
- Dark locations
- Locations with a flickering light source (fluorescent lamp, candle light, etc.)
About panorama playback
You can operate the zoom lever/zoom button to enlarge pictures taken in
[Panorama Shot] mode in the same way as with other still pictures. You can also
press to automatically scroll pictures in the same way as when playing back a
motion picture.
• Unlike motion picture playback, you cannot perform fast forward or rewind
by pressing or while the pictures are scrolling automatically. (You can
perform single-frame forward or rewind while the automatic scrolling operation
is paused.)
- 52 -
Taking pictures according to the scene [Scene Mode]
Takes pictures of scenes with fast movement, e.g. sports.
Tips
• Stand at least 5 m (16 feet) away.
[Sports]
Notes
• Shutter speed may slow down up to 1 second.
Takes pictures of people and nightscapes with close to actual brightness.
Tips
• Use flash.
• Subject should not move.
• Tripod, self-timer recommended.
[Night Portrait]
Notes
• Shutter speed may slow down up to 8 seconds.
• After recording, the shutter may stay closed (up to 8 seconds) to process the
signal. This is not a malfunction.
Takes clear pictures of night scenes.
Tips
• Tripod, self-timer recommended.
[Night
Scenery]
Notes
• Shutter speed may slow down up to 8 seconds.
• After recording, the shutter may stay closed (up to 8 seconds) to process the
signal. This is not a malfunction.
Takes natural-looking pictures of food.
[Food]
- 53 -
Taking pictures according to the scene [Scene Mode]
Uses weak flash to bring out skin colors.
([Baby1] and [Baby2] can be set separately.)
Use cursor button to select [Age] and press [MENU/SET].
Use cursor button to select [SET] and press [MENU/SET].
Set birthday with cursor button, and press [MENU/SET].
Use cursor button to select [Exit] and press [MENU/SET].
Tips
• Make sure [Age] is [ON] before taking a picture.
[Baby]
Notes
• Age display format depends on [Language] setting.
• Shutter speed may slow down up to 1 second.
• [Age] print setting can be made on your computer using the supplied CD-ROM
“PHOTOfunSTUDIO”.
Records pet’s age when taking pictures.
• Refer to [Baby] for other tips and notes.
[Pet]
Takes clear pictures of scenes such as sunsets.
[Sunset]
Prevents blurring of subject in dark, indoor conditions.
Select the aspect ratio and the picture size with cursor button and press [MENU/
SET].
[High Sens.]
Most suitable for taking pictures such as a landscapes through the
transparent glass of a train/vehicle or building.
Notes
• If there are stains such as dust or a reflection on the glass, the camera may
focus on the glass instead of a subject.
• The color of pictures may appear unnatural due to the color of the glass.
(You may be able to reproduce the appropriate color by adjusting the White
Balance.)
[Glass
Through]
A frame is superimposed over the image.
Use cursor button to select the frame, and then press [MENU/SET].
Notes
[Photo Frame]
• The recording pixel level is 5 M (
• Guide lines cannot be displayed.
).
- 54 -
Using the [Rec] menu
[Picture Size]
Set the size (number of pixels) of still pictures. Number of pictures which can be recorded
depends on this setting.
■
■
Recording mode:
Settings:
DMC-FH6 DMC-FH4
DMC-S2
DMC-S5
Recording pixel level type
Recording pixel level type
14 M 4320×3240
16 M
4608×3456
3648×2736
2560×1920
2048×1536
640×480
∗
∗
3648×2736
2560×1920
2048×1536
640×480
10 M
10 M
5 M
3 M
5 M
3 M
∗
∗
0.3 M
0.3 M
12.5 M
10.5 M
10.5 M
4320×2880
4320×2432
3232×3232
14 M
4608×3027
4608×2592
3456×3456
12 M
12 M
∗
This setting is not available in
([Intelligent Auto] Mode).
represent the aspect ratios of the still pictures.
Mosaic effect may appear depending on subject and recording conditions.
●
●
Setting guide
Larger picture size
Crisper picture
Smaller picture size
Coarser picture
Lower recording
capacity
Higher recording
capacity
- 55 -
Using the [Rec] menu
[Rec Quality]
Set the picture size of motion pictures.
■
■
Recording mode:
Settings:
Picture Quality
[HD]
Picture Size
1280 × 720 pixels
640 × 480 pixels
320 × 240 pixels
No. of Frames
Picture Aspect Ratio
1
2
∗
∗
24 fps / 30 fps
16:9
[VGA]
30 fps
4:3
3
∗
[QVGA]
1 DMC-S5
∗
2 DMC-FH6, DMC-FH4, DMC-S2
∗
3 [QVGA] is fixed when recording to the built-in memory.
∗
Depending on the motion picture recording environment, static electricity or
electromagnetic waves may cause the screen to go black momentarily or noise to be
recorded.
If you attempt to play motion pictures recorded with the camera on other devices,
playback may not be possible, or the picture or sound quality may be poor.
Additionally, incorrect recording information may be indicated.
●
●
[Sensitivity]
Set ISO Sensitivity (sensitivity to lighting) manually.
We recommend higher settings to take clear pictures in darker locations.
■
■
Recording mode:
Settings: [Intelligent ISO] / [100] / [200] / [400] / [800] / [1600]
Setting guide
[Sensitivity]
[100]
[1600]
Location
Bright
(outdoors)
Slow
Low
Increased
Dark
(recommended)
Shutter speed
Interference
Fast
High
Less
Jitter of the subject
[
] is automatically set in a range up to 1600 based on subject movement and
●
brightness.
- 56 -
Using the [Rec] menu
[White Balance]
Adjust coloring to suit light source if colors otherwise appear unnatural.
■
■
Recording mode:
Settings: [AWB] (automatic) /
(outdoor, shade) /
(outdoor, clear sky) /
(incandescent lighting) /
) / (set manually)
(outdoor, cloudy sky) /
(uses value set in
[AWB] operational range:
10000K
Blue sky
9000K
8000K
Cloudy sky (rain)
Shade
7000K
6000K
Sunlight
5000K
White fluorescent lighting
4000K
3000K
2000K
Incandescent lighting
Sunset/sunrise
Candlelight
K=Kelvin color Temperature
■
Setting White Balance manually (
)
Only takes picture of white
objects within frame (step
Select
and press [MENU/SET].
)
Point the camera towards a white object (e.g. paper)
and press [MENU/SET].
• White Balance is set to
.
• The White Balance you set is retained even after
the power is turned off.
• White Balance setting may not be possible if the
subject is too bright or too dark. In such cases,
adjust the subject to an appropriate brightness, and
then set the White Balance again.
A picture may appear reddish or bluish when the White Balance is outside the [AWB]
operational range. Even if the White Balance is within the [AWB] operational range, this
function may not work correctly if there are multiple light sources.
●
Under fluorescent lighting, LED lighting fixture etc., the appropriate White Balance will
●
●
●
vary depending on the lighting type, so use [AWB] or [
].
White Balance setting is fixed to [AWB] in the following Scene Modes:
[Scenery], [Night Portrait], [Night Scenery], [Food], and [Sunset]
If the Scene Mode is changed, the white balance setting returns automatically to [AWB].
- 57 -
Using the [Rec] menu
[AF Mode]
Method of aligning focus can be changed according to position and number of subjects.
■
■
Recording mode:
Settings:
/
/
Taking front-on
pictures of people
Recognizes faces (up to 15 people) and adjusts exposure and focus
accordingly.
(Face Detection)
AF area
Yellow : When the shutter button is pressed halfway, the frame turns
green when the camera is focused.
White : Displayed when more than one face is detected. Other faces
that are the same distance away as faces within the yellow
AF area are also focused.
Subject not centered
in picture
Focuses on up to 23 points in each AF area.
(AF area not displayed until focused)
(23-area-focusing)
Determined position
for focus
Focuses on AF area in center of picture.
(Recommended when focus is difficult to align)
(1-area-focusing)
Cannot set to “Face Detection” in the following cases:
[Panorama Shot], [Night Scenery], [Food] Scene Modes
If the camera misinterprets a non-human subject as a face in the “Face Detection”
setting, switch to another setting.
If conditions prevent the face from being recognized, such as when the movement of
●
●
●
the subject is too rapid, the [AF Mode] setting switches to
(23-area-focusing).
- 58 -
Using the [Rec] menu
[i.Exposure]
Automatically adjusts contrast and exposure to give more lifelike colors when there is
significant contrast between background and subject.
■
■
Recording mode:
Settings: [ON] / [OFF]
When [i.Exposure] works, the color of
Even if [Sensitivity] is set to [100], when [i.Exposure] is activated, pictures may be taken
at a higher ISO Sensitivity than the setting.
changes.
●
●
[i.Resolution]
You can use the camera’s super resolution technology to record still pictures with sharper
outlines and clearer resolution. Also, when [i.ZOOM] is set, the zoom ratio can be
increased two times higher than the original zoom ratio while preventing deterioration of
picture quality.
■
■
Recording mode:
Settings: [ON] / [i.ZOOM] / [OFF]
●
●
●
The setting is fixed to [i.ZOOM] in [Intelligent Auto] Mode.
The setting is fixed to [ON] in [High Sens.] Scene Mode, [OFF] in [Panorama Shot]
Scene Mode, and to [i.ZOOM] in other Scene Modes.
[Digital Zoom]
Zoom 4 times further than Optical/Extended Optical Zoom. (Note that enlarging will
decrease picture quality with Digital Zoom.)
■
■
Recording mode:
Settings: [ON] / [OFF]
When Digital Zoom is used simultaneously with i.Zoom, you can only increase the
zoom ratio up to 2 times.
●
- 59 -
Using the [Rec] menu
DMC-FH6
[Burst]
Enables still pictures to be taken in succession while the shutter button is pressed fully.
■
■
Recording mode:
Settings:
Item
Settings
Maximum burst speed: Approx. 1.5 fps
• You can record a series of still pictures successively until the card or built-in
memory is full, but at some point the burst speed drops. (The timing at
which the burst speed drops varies depending on the type of card and the
number of recording pixels.)
• The camera fixes its focus with the first picture to be taken. Both exposure
and White Balance are adjusted for each of a picture.
• The camera automatically fixes a succession of still pictures into three
when the self-timer is used.
[Burst]
• When burst is selected, the flash is unavailable.
Maximum burst speed: Approx. 10 fps
∗
• Number of pictures taken using burst
Built-in memory Approx. 15 pictures or more
Card Approx. from 15 pictures to maximum of 100 pictures
The number of pictures that can be taken using burst varies depending
on the recording conditions and the type of card.
∗
[Hi-Speed Burst]
• The camera fixes its focus along with both exposure and White Balance,
with the first picture to be taken.
• [Sensitivity] is automatically adjusted.
• The camera automatically fixes a succession of still pictures into three
when the self-timer is used.
• When burst is selected, the flash is unavailable.
∗
• Number of pictures taken using burst : maximum of 5 pictures
∗
The number of pictures that can be taken using burst varies depending
on the recording conditions and the type of card.
• The camera fixes its focus along with both exposure and the amount of
light to be emitted from a flash, based on the first picture taken.
• [Sensitivity] is automatically adjusted.
• The camera automatically fixes a succession of still pictures into five when
the self-timer is used.
[Flash Burst]
[OFF]
Cancels burst mode.
- 60 -
Using the [Rec] menu
About [Hi-Speed Burst] and [Flash Burst]
• The settings can be made in [Normal Picture] Mode only.
●
prior to the setting.
Picture Aspect Ratio
Picture Size
3 M
4:3
3:2
2.5 M
16:9
1:1
2 M
2.5 M
When ISO Sensitivity is set to high, or when the shutter speed becomes slow in dark
locations, the burst speed may become slow.
When you track subjects in motion and take successive pictures in where there is a
significant difference between light and dark areas, it may not be possible to achieve
the optimal exposure.
●
●
The setting is fixed to [OFF] in [Panorama Shot] and [Photo Frame] Scene Modes.
●
DMC-FH4
DMC-S5
DMC-S2
[Burst]
Enables a rapid succession of still pictures to be taken. Succession of still pictures taken
while shutter button is held down.
■
■
Recording mode:
Settings:
/ [OFF]
DMC-FH4
DMC-S5
DMC-S2
Maximum burst speed: Approx. 1.5 fps
Maximum burst speed: Approx. 1.4 fps
●
• You can record a series of still pictures successively until the card or built-in memory
is full, but at some point the burst speed drops. (The timing at which the burst speed
drops varies depending on the type of card and the number of recording pixels.)
Focus is fixed from first picture. Exposure and White Balance is adjusted for each
picture.
The camera automatically fixes a succession of still pictures into three when the self-
timer is used.
Burst speed may be reduced if ISO Sensitivity is set to high, or if shutter speed is
reduced in darker locations.
●
●
●
When burst is selected, the flash is disabled.
●
●
When you record subjects in motion where there is a significant difference between
light and dark areas, it may not be possible to achieve the optimal exposure.
The setting is fixed to [OFF] in [Panorama Shot] and [Photo Frame] Scene Modes.
●
- 61 -
Using the [Rec] menu
[Color Mode]
Set color effects.
■
■
Recording mode:
Settings: [STANDARD] / [VIVID] (sharper) / [B&W] / [SEPIA] / [Happy]
1
2
∗
∗
1 [Normal Picture] Mode and [Motion Picture] Mode only
∗
2 [Intelligent Auto] Mode only
∗
[AF Assist Lamp]
Illuminates lamp when dark to facilitate focus alignment.
■
■
Recording mode:
Settings: [ON] : Lamp illuminated with halfway press of shutter
button (
and larger AF area displayed)
[OFF] : Lamp off (taking pictures of animals in dark, etc.)
The AF Assist Lamp has an effective distance of approx. 1 m
(3.3 feet)
• Do not block the lamp with your fingers or look at it from close
range.
• The AF Assist Lamp’s effective distance becomes shorter when
using the zoom and depending on subject conditions.
The setting is fixed to [OFF] in the following Scene Modes:
[Scenery], [Night Scenery], [Sunset] and [Glass Through] Scene
Modes
●
●
AF Assist Lamp
[Red-Eye Removal]
Automatically detects red-eye and corrects still picture data when recording with flash
red-eye reduction ( ).
■
■
Recording mode:
Settings: [ON] / [OFF]
This setting will work only when [AF Mode] is
Depending on the circumstance, it may not be possible to correct red-eye.
(Face Detection).
●
●
●
When the function setting is [ON], a
appears with the flash icon.
- 62 -
Using the [Rec] menu
[Stabilizer]
Automatically detects and prevents jitter.
■
■
Recording mode:
Settings: [ON] / [OFF]
Cases where Optical Image Stabilizer may be ineffective:
Heavy jitter, high zoom ratio (also in the Digital Zoom range), fast-moving objects,
indoors or in dark locations (due to low shutter speed)
●
[Date Stamp]
Still pictures can be taken with the recording date and time stamped on the still picture.
■
■
Recording mode:
Settings: [W/O TIME] / [WITH TIME] / [OFF]
Date stamps on still pictures cannot be erased.
The date cannot be stamped when [Burst] is set.
●
●
●
●
The setting is fixed to [OFF] in [Panorama Shot] Scene Mode.
Do not request date printing in store or make date printing on printer for still pictures
with date stamps. (Date printing may be overlapping.)
Cannot change the setting in [Intelligent Auto] Mode. The setting in other Recording
Mode is applied.
●
[Clock Set]
Set the clock. Same function as that in [Setup] menu.
- 63 -
Different playback methods
[Playback Mode]
Recorded pictures can be played back in a variety of ways.
Press the Playback button
Display the screen for [Playback
Mode] selection
Select the method of playback
When no card is inserted, pictures are played back from the built-in memory.
The [Playback Mode] automatically becomes [Normal Play] when switching from
recording mode to playback mode.
●
●
- 64 -
Different playback methods [Playback Mode]
[Slide Show]
Automatically play pictures in order and to music. Recommended when viewing on TV
screen.
Use cursor button to select the playback method and press
[MENU/SET]
[All]
Play all.
[Category
Selection]
Select category and playback.
[Favorite]
Play back pictures set as [Favorite].
Use cursor button to set playback effects and press
[MENU/SET]
[Effect] (Select music and effects according to picture atmosphere)
[AUTO] (only available with [Category Selection] setting) / [NATURAL] / [SLOW] / [SWING] /
[URBAN] / [OFF]
[Setup]
[1 SEC.] / [2 SEC.] / [3 SEC.] / [5 SEC.] (Only available when [Effect] is
[Duration]
[OFF])
[Repeat]
[Music]
[ON] / [OFF]
[ON] / [OFF]
Select [Start] with cursor button and press [MENU/SET]
■
Operations during Slide Show
Pause/Play
(While paused)
Previous
(While paused)
Next
• Volume can be adjusted with the zoom
lever or the zoom button.
Stop
- 65 -
Different playback methods [Playback Mode]
When [URBAN] has been selected, the picture may appear in black and white as a
screen effect.
●
When panorama pictures are played back, the [Duration] setting is disabled.
Part of [Effect] cannot be used when displaying pictures recorded in portrait position.
Music effects cannot be added.
Motion pictures cannot be played back in a Slide Show. The initial screens of motion
pictures are played back as still pictures in the Slide Show.
●
●
●
●
[Filtering Play]
You can refine the selection of pictures to be viewed by narrowing them down to pictures
in selected categories or to favorite pictures, and then view those pictures.
Select the method to narrow down the displayed pictures
[Category
Selection]
Display only pictures in the selected category.
[Favorite]
Display pictures set as [Favorite].
When [Category Selection] has been selected in step , select
a category
[Category]
Recording information such as Scene Modes
[Portrait] /
/ [Soft Skin] / [Night Portrait] /
/ [Panorama Shot] / [Sunset] /
/ [Baby]
[Scenery] /
/ [Glass Through]
[Night Portrait] /
[Sports]
/ [Night Scenery] /
[Baby]
[Pet]
[Food]
[Motion Picture]
- 66 -
Retouching pictures
[Auto Retouch]
You can adjust the color and brightness of a still picture to bring them into balance.
• New pictures are created after editing pictures with [Auto Retouch]. Before starting to
edit, make sure that there is enough free space in the built-in memory or memory card.
DMC-FH6
Select a still picture to retouch during playback and press
Use cursor button to select [Auto Retouch] and press [MENU/
SET]
A still picture retouched with colors and brightness is displayed.
Use cursor button to select [ON] and press [MENU/SET]
• A confirmation screen is displayed. If you select [Yes], the new retouched still
picture is saved.
• When [OFF] is selected, you can restore a picture to its original condition (before
retouching).
DMC-FH4
DMC-S5
DMC-S2
Select a still picture to retouch during playback and press
A still picture retouched with colors and brightness is displayed.
Press [MENU/SET]
• A confirmation screen is displayed. If you select [Yes], the new retouched still
picture is saved.
The retouch effect may be less apparent in some still pictures.
Some still pictures may have higher noise levels after retouching.
It may not be possible to use [Auto Retouch] with still pictures that have already been
retouched.
●
●
●
It may not be possible to retouch still pictures recorded with other cameras.
[Auto Retouch] is unable to be performed in the following cases:
• Motion pictures
●
●
• Still pictures recorded in [Panorama Shot] Scene Mode
• Still pictures recorded in [Photo Frame] Scene Mode
- 68 -
Retouching pictures
DMC-FH6
[Beauty Retouch]
Still pictures taken by the camera that recognize the subject as a face can be retouched
using the makeup effect etc., to enhance the portrait.
• New pictures are created after editing pictures with [Beauty Retouch]. Before starting to
edit, make sure that there is enough free space in the built-in memory or memory card.
Select a still picture that has a face in it and press
Use cursor button to select [Beauty Retouch] and press
[MENU/SET]
Use cursor button to select a face and press [MENU/SET]
• Press or to move the cursor to select a face. If the cursor does not move to
a face, it means that the camera cannot detect this face and thus it cannot be
selected.
Set the effects
Use or to select the effect that you want to apply and press
Use or to select the setting and press
• Repeat steps and to set another effect.
Menu item
Settings
Creates smooth, clear skin or enhances the whiteness of eyes
and teeth.
[Aesthetic Retouch]
[Foundation]
Adjusts the skin color.
Enhances the color of lips, renders faces with a three-dimensional
look, or creates a sharper outline of the eyes.
[Make Up Retouch]
Press [MENU/SET] to end the retouching operation
Use cursor button to select [Yes] and press [MENU/SET]
• A screen comparing the original picture to the picture with effects applied is
displayed.
Press [MENU/SET]
• A confirmation screen is displayed. If you select [Yes], the new retouched still
picture is saved.
- 69 -
Retouching pictures
You cannot retouch an already-retouched subject or two or more subjects at once. To
perform such an operation, save the picture once and then select a subject that you
want to retouch again.
The brightness or color between a picture viewed before saving and the saved picture
may be different.
●
●
It may not be possible to retouch still pictures taken with other cameras.
You cannot retouch motion pictures and still pictures recorded in [Panorama Shot]
Scene Mode.
●
●
If the face is not detected properly, it may not be possible to retouch the face as
desired.
To take a still picture suitable for [Beauty Retouch]:
• Take a picture of the face from the front
●
●
• Avoid taking a picture under very low lighting conditions
• Take a clear picture of the area that you want to retouch
Reallusion is a trademark of Reallusion Inc.
●
- 70 -
Using the [Playback] menu
You can set the recorded picture to upload to the image-sharing websites, edit the picture
(for example, trimming), and set a protection setting in the picture.
• Depending on the [Playback Mode], some [Playback] menu items are not displayed.
• It may not be possible to set or edit pictures taken with other cameras.
• New pictures are created after editing pictures with tools such as [Resize] and
[Cropping]
. Before starting to edit, make sure that there is enough free
DMC-FH6
space in the built-in memory or memory card.
[Upload Set]
You can select pictures on the camera for uploading to image-sharing websites
(Facebook or YouTube).
• Only still pictures can be uploaded to Facebook and only motion pictures can be
uploaded to YouTube.
making [Upload Set] settings.
Use cursor button to select [SINGLE] or [MULTI], and then
press [MENU/SET]
Select picture and make setting
[SINGLE]
Use cursor button to select
[MULTI]
●
●
Use cursor button to select picture and press
picture and press [MENU/SET] [MENU/SET]
• To cancel
→ Press [MENU/SET]
again.
• To execute
→ Use cursor button to
select [OK] and press
[MENU/SET].
• Confirmation screen is
displayed. If you select
[Yes], the operation is
executed.
Web upload setting
• To cancel
→ Press [MENU/SET] again.
Web upload setting
■
Uploading to image-sharing websites
When setting [Upload Set], the built-in uploading tool automatically makes copies
- 71 -
Using the [Playback] menu
■
To clear all
Select [CANCEL] in step
and select [Yes].
Not available on cards with less than 512 MB.
●
[Resize]
Picture size can be reduced to facilitate e-mail attachment and use in web pages, etc.
(Still pictures recorded at the smallest recording pixel level cannot be further reduced.)
■
[SINGLE]
Use cursor button to select [SINGLE] and press [MENU/SET]
Use cursor button to select a still picture and press
[MENU/SET]
Use cursor button to select size and press [MENU/SET]
Current size
Size after change
• Confirmation screen is displayed. If you select [Yes], the operation is executed.
- 72 -
Using the [Playback] menu
■
[MULTI]
Use cursor button to select [MULTI] and press [MENU/SET]
Use cursor button to select size and press [MENU/SET]
Use cursor button to select a still picture and press
[MENU/SET] (up to 50 pictures)
• To cancel
→ Press [MENU/SET] again.
• To execute
→ Use cursor button to select
Resize setting
[OK] and press [MENU/SET].
Number of pixels before/
after resizing
• Confirmation screen is displayed. If you select [Yes], the operation is executed.
Picture quality is reduced after resizing.
Cannot resize the following pictures.
• Motion pictures
●
●
• Still pictures already stamped with the date and time
• Panorama pictures
DMC-FH6
[Cropping]
Enlarge your still pictures and crop unwanted areas.
Use cursor button to select a still picture, and then press
[MENU/SET]
Select area to crop and press [MENU/SET]
Expand
Change position
• Confirmation screen is displayed. If you select [Yes], the operation is executed.
Picture quality is reduced after cropping.
Cannot crop the following pictures.
• Motion pictures
●
●
• Still pictures already stamped with the date and time
• Panorama pictures
- 73 -
Using the [Playback] menu
[Favorite]
By labeling your favorite pictures with a star ( ), you can play back your favorite pictures
only, or you can delete all pictures except your favorites.
Use cursor button to select [SINGLE] or [MULTI] and press
[MENU/SET]
Use cursor button to select picture and press [MENU/SET]
[SINGLE]
[MULTI]
●
●
Favorite picture setting
Favorite picture setting
• To cancel → Press [MENU/SET] again.
■
To clear all
Select [CANCEL] in step
and select [Yes].
- 74 -
Using the [Playback] menu
DMC-FH6
[Print Set]
Picture/picture no./date printing settings can be made for when printing with DPOF print-
compatible shops or printers. (Ask at shop to check compatibility)
For more information visit:
http://panasonic.jp/dc/dpof_110/white_e.htm
Use cursor button to select [SINGLE] or [MULTI] and press
[MENU/SET]
Use cursor button to select picture and press [MENU/SET]
Use cursor button to set number of pictures and press [MENU/
SET]
(repeat steps
and
when using [MULTI] (up to 999 pictures))
[SINGLE]
[MULTI]
●
●
Date print set
No. to print
Date print set
No. to print
• Date print setting/release → Press
■
To clear all
Select [CANCEL] in step
and select [Yes].
Depending on the type of printer, the printer settings may take priority over camera
settings.
●
Cannot be set for files that are not compliant with the DCF standard.
Some DPOF information set by other equipment cannot be used. In such cases, delete
all of the DPOF information and then set it again with this camera.
Date print setting cannot be made for still pictures that have been taken with [Date
Stamp].
●
●
●
●
Print setting cannot be made for motion pictures.
- 75 -
Using the [Playback] menu
[Protect]
Set protection to disable picture deletion. Prevents deletion of important pictures.
Use cursor button to select [SINGLE] or [MULTI] and press
[MENU/SET]
Use cursor button to select picture and press [MENU/SET]
[SINGLE]
[MULTI]
●
●
Picture protected
Picture protected
• To cancel → Press [MENU/SET] again.
■
To clear all
Select [CANCEL] in step
and select [Yes].
■
To cancel while releasing all
Press [MENU/SET].
May not be effective when using other devices.
●
- 76 -
Using the [Playback] menu
[Copy]
You can copy pictures between built-in memory and memory card.
Use cursor button to select the copy method (direction) and
press [MENU/SET]
: Copy all pictures from built-in memory to card (go to step ).
: Copy 1 picture at a time from card to built-in memory.
Select picture with cursor button and press [MENU/SET]
Use cursor button to select [Yes] and press [MENU/SET]
• To cancel → Press [MENU/SET].
• After all the pictures are copied from the built-in memory to the memory card, the
display returns automatically to the playback screen.
Copying pictures may take several minutes. Do not turn off power or perform other
operations during copying.
●
If identical names (folder/file numbers) are present in the copy destination, a new
folder for copying will be created when copying from built-in memory to card (
●
).
Identically-named files will not be copied from card to built-in memory (
The following settings are not copied. Set them again after copying.
).
●
●
- [Protect] - [Favorite] - [Print Set]
DMC-FH6
Only pictures from Panasonic digital cameras (LUMIX) may be copied.
- 77 -
Viewing on TV screen
You can view pictures on a TV screen by connecting your camera to your TV with the AV
cable.
Getting Ready:
• Turn off both camera and TV.
Connect camera to TV
Turn on TV
Set to auxiliary input.
●
Turn on camera
Press the Playback button
Check socket direction and insert
straight in.
(Damage to socket shape can lead to
faulty operation.)
Yellow: To video socket
AV cable
(Optional)
White: To audio socket
■
When TVs or DVD recorders have an SD card slot
Insert the SD Memory Card into the SD card slot
• You can play back only still pictures.
• You cannot play back motion pictures.
• You may not be able to play back panorama pictures. Also you cannot perform automatic
scrolling playback of panorama pictures.
• When using both SDHC and SDXC Memory Cards, be sure to play each type of card
in equipment compatible with the particular format.
- 78 -
Viewing on TV screen
Also consult TV operating manual.
Always use a genuine Panasonic AV cable (optional).
●
●
●
You can play back pictures on TVs in other countries (regions) which use the NTSC or
PAL system when you set [Video Out] in [Setup] menu. (DMC-FH6PU/DMC-FH4PU/
DMC-S5PU/DMC-S2PU/DMC-FH6PR/DMC-FH4PR/DMC-S5PR only)
Pictures rotated to portrait may be blurred slightly.
Change picture mode settings on TV if aspect ratios are not displayed correctly on
widescreen or high-definition televisions.
●
●
- 79 -
Using with your PC
Still/motion pictures can be copied from the camera to your computer by connecting the
two together.
• Some computers can read directly from the camera’s memory card.
For details, see the manual for your computer.
• If your computer does not support SDXC Memory Cards a message will be displayed
requesting you to format the card. (Do not format the card. This will erase recorded
pictures.) If the card is not recognized, refer to the following support website.
http://panasonic.net/avc/sdcard/information/SDXC.html
• You can use pictures copied to your computer for printing, attaching them to e-mail, or
other operation. The “PHOTOfunSTUDIO” software on the CD-ROM (supplied) enables
you to perform these functions easily.
Using the supplied software
The supplied CD-ROM contains the following software.
Install the software on your computer before using.
■
PHOTOfunSTUDIO 8.0 LE (Windows XP/Vista/7)
This software allows you to copy still pictures or motion pictures to a computer and sort
the copied pictures by their recording date and time, model name of the digital camera
used, or other attributes. You can write pictures to a DVD, create a Slide Show using
your preferred music or effects and so on before saving it to a DVD.
■
LoiLoScope 30 day full trial version (Windows XP/Vista/7)
LoiLoScope is a video editing software where that draws out the full power of your
PC. Creating videos is as easy as organizing cards on top of a desk. Use your music,
picture and video files to create videos to share with your friends and family by burning
it to a DVD, uploading it to websites, or simply share your videos with your friends via
e-mail.
• This will only install a shortcut to the trial version download site.
For more information on how to use LoiLoScope, read the LoiLoScope
manual available for download at the link below.
Manual URL: http://loilo.tv/product/20
- 80 -
Using with your PC
Installing supplied software (PHOTOfunSTUDIO)
This software allows you to acquire pictures to the PC, and also categorize these
acquired pictures by their recording date or the model name of the camera used.
• Before inserting the CD-ROM, close all running applications.
Check the environment of your PC
Operating environment of PHOTOfunSTUDIO 8.0 LE
Windows XP (32 bit) SP3
OS
Windows Vista (32 bit) SP2
Windows 7 (32 bit/64 bit) and SP1
Windows XP
Windows Vista
Windows 7
Pentium III 500 MHz or higher
800 MHz or higher
1 GHz or higher
CPU
1024 × 768 pixels or more
(1920 × 1080 pixels or more recommended)
Display
Windows XP
512 MB or more
Windows Vista
RAM
1 GB or more (32 bit)
Windows 7
2 GB or more (64 bit)
Free hard disk space 450 MB or more for installing software
• Refer to the Operating Instructions of “PHOTOfunSTUDIO” (PDF) for further
information about the operating environment.
Insert the CD-ROM with the supplied software
When you insert the supplied CD-ROM, the install menu will start.
Click on the [Applications] on the install menu
Click on the [Recommended Installation]
• Proceed with installation according to messages appearing on the screen.
The software compatible with your PC will be installed.
PHOTOfunSTUDIO is not compatible with Mac.
●
●
- 81 -
Using with your PC
Copying still pictures and motion pictures
Check socket direction and insert straight in.
(Damage to socket shape can lead to faulty operation.)
Getting Ready:
• Charge the battery
sufficiently.
• When importing pictures from
the built-in memory, remove
any memory cards.
• Turn on the camera and
computer
USB connection cable
(always use cable supplied)
[Access] (sending data)
• Do not disconnect
the USB connection
cable while [Access] is
displayed.
Connect camera to computer
• Please make sure you use the supplied USB connection cable.
Use of cables other than the supplied USB connection cable may cause
malfunction.
Use cursor button on the camera to select [PC], and press
[MENU/SET]
Use “PHOTOfunSTUDIO” to copy pictures to your computer
• For details on how to use “PHOTOfunSTUDIO”, see the “PHOTOfunSTUDIO”
manual (PDF).
• You can save pictures to your computer by dragging and dropping folders and files
containing the pictures that you want to copy into other folders in the computer.
- 82 -
Using with your PC
■
Folder and file names on computer
DCIM (Still/motion pictures)
100_PANA (Up to 999 pictures/folder)
P1000001.JPG
JPG:
:
Windows
●
●
Still pictures
P1000999.JPG
Drives are displayed
in “My Computer” or
“Computer” folder.
MOV:
Motion pictures
101_PANA
1
∗
:
999_PANA
MISC (Favorite)
Mac
2,
3
Drives are displayed on
the desktop.
(Displayed as “LUMIX”,
“NO_NAME”, or
“Untitled”.)
∗ ∗
AD_LUMIX (Folder for Web uploading)
LUMIXUP.EXE (Uploading tool)
1 New folders are created in the following cases:
• When pictures are taken to folders containing files numbered 999.
∗
• When using cards already containing the same folder number (for example, pictures taken with
other cameras, etc.).
2 Note that pictures cannot be uploaded to image-sharing websites if the files in the AD_LUMIX
folder are deleted.
∗
3 This folder is not created in the built-in memory.
∗
■
■
To cancel connection
Click “Safely Remove Hardware” in the Windows System Tray
When using Windows XP, Windows Vista, Windows 7, or Mac OS X
The camera can be connected to your computer even if you select [PictBridge (PTP)] in
the step
on the previous page.
• Only picture output can be performed.
• It may not be possible to import if there are 1000 or more pictures on the card.
Do not use any other USB connection cables except the supplied one.
Turn off power before inserting or removing memory cards.
When the battery begins to run out during communication, a warning beep sounds.
Cancel communication via your computer immediately. Use a sufficiently charged
battery.
●
●
●
For more details, consult your computer operating manual.
●
- 83 -
Using with your PC
Uploading pictures to image-sharing websites
Using the uploading tool ([LUMIX Image Uploader]), you can upload still pictures and
motion pictures to image-sharing websites (Facebook or YouTube).
There is no need to copy pictures to your computer or install specialized software.
Uploading pictures from the camera is easy with a computer connected to a network,
even when you are away from your regular computing environment.
• This tool supports only computers that run on Windows XP, Windows Vista, and
Windows 7.
• For more information, read the operating instructions (PDF) for the [LUMIX Image
Uploader].
Getting ready:
• Connect your computer to the Internet
• Create an account for the applicable image-sharing website and prepare your login
information
Double-click “LUMIXUP.EXE” to start it
• If you have installed “PHOTOfunSTUDIO” from the CD-ROM (supplied),
“Uploading tool ([LUMIX Image Uploader])” may start automatically.
Select the upload destination
• Do the further steps in accordance with the instructions displayed on the computer
screen.
Because YouTube and Facebook services and specifications are subject to change,
operation of online services cannot be guaranteed in the future. Available services and
screens are subject to change without notice.
●
(This service is available as of November 1, 2011)
Do not upload pictures protected by copyright except when you are the copyright holder
or permission has been obtained from the corresponding copyright holder.
●
The pictures may contain information that identifies an individual, such as the title of
●
a picture, recording date and time, information of the location where a picture was
taken using a camera with GPS function, and so on. Before uploading the pictures to
image-sharing websites, check the pictures carefully for information that should not be
disclosed.
- 84 -
Printing
You can connect directly to a PictBridge-compatible printer for printing.
• Some computers can read directly from the camera’s memory card.
For details, see the manual for your computer.
• Do not disconnect the USB connection cable when
the cable disconnection icon is displayed (may
not be displayed with some printers).
Getting Ready:
• Charge the battery sufficiently.
• When copying pictures from the
built-in memory, remove any memory
cards.
• Adjust the print quality or other
settings on your printer, as needed.
• Turn on the camera and printer
Check socket direction and insert straight in.
(Damage to socket shape can lead to faulty
operation.)
USB connection cable
(always use cable supplied)
Connect camera to printer
• Please make sure you use the supplied USB connection cable. Use of cables
other than the supplied USB connection cable may cause malfunction.
Use cursor button on the camera to select [PictBridge (PTP)],
and press [MENU/SET]
Use cursor button to select a picture to print and press
[MENU/SET]
Use cursor button to select [Print start] and press [MENU/SET]
■
To cancel print Press [MENU/SET]
Do not use any other USB connection cables except the supplied one.
Disconnect USB connection cable after printing.
Turn off power before inserting or removing memory cards.
When the battery begins to run out during communication, a warning beep sounds.
Cancel printing and disconnect USB connection cable. Use a sufficiently charged
battery.
●
●
●
●
- 85 -
Printing
Printing multiple pictures
Connect camera to printer
• Please make sure you use the supplied USB connection cable. Use of cables
other than the supplied USB connection cable may cause malfunction.
Use cursor button on the camera to select [PictBridge (PTP)],
and press [MENU/SET]
Press
Use cursor button to select item and press [MENU/SET]
• [Multi Select]:
Scroll between pictures with cursor button select pictures
to print with [MENU/SET]. (Press [MENU/SET] again to
release selection.)
Use cursor button to select [OK] and press [MENU/SET].
Print all pictures.
• [Select All]:
DMC-FH6
• [Print Set (DPOF)]
• [Favorite]:
:Print pictures selected in [Print Set].
Print pictures selected as [Favorite].
Use cursor button to select [Print start] and press [MENU/SET]
Select [Yes] if print confirmation screen is displayed.
●
●
●
An orange “ ” displayed during printing indicates an error message.
●
Print may be divided into several times if printing a large amount of pictures.
(Remaining sheets display may differ from set number.)
- 86 -
Printing
Making print settings on the camera
(Make settings before selecting [Print start])
Use cursor button to select the item and press [MENU/SET]
Item
Settings
[Print with
Date]
[ON] / [OFF]
Set number of pictures (up to 999 pictures)
[Num.of
prints]
[Paper Size]
When
is selected, the printer settings take priority.
[Page
Layout]
(printer takes priority) /
(1 picture, with border) /
(1 picture, no border) /
(2 pictures) / (4 pictures)
Use cursor button to select setting and press [MENU/SET]
Items may not be displayed if incompatible with printer.
●
●
To arrange
“2 pictures” or
“4 pictures” in the same still picture, set the number of
prints for the still picture to 2 or 4.
To print to paper sizes/layouts not supported by this camera, set to
settings on the printer. (Consult your printer’s operating manual.)
[Print with Date] and [Num.of prints] are not shown when you have selected [Print Set]
and make
●
●
●
●
DMC-FH6
settings.
Even with completed [Print Set] settings, dates may not be printed, depending on the
DMC-FH6
shop or printer used.
When setting [Print with Date] to [ON], check the date printing settings on the printer
(printer settings may be prioritized).
Print with date and text
■
Printing in store
Only recording date can be printed. Request date printing in store.
• When printing still pictures of 16:9 Aspect Ratio, check in advance that the store can
accept this size.
■
■
Using computer
Print settings for recording date and text information can be made using the supplied
CD-ROM “PHOTOfunSTUDIO”.
Using printer
Recording date can be printed by setting [Print with Date] to [ON] when connecting to a
printer compatible with date printing.
- 87 -
List of LCD monitor displays
■
In recording
1
2
3
4
5
6
7
14
13
12
11
8
10
9
1
2
9
10
Current date/time
3
Recording state
11
12
13
4
5
14
∗
6
7
8
RXXhXXmXXs
Focus range
3.3ft
-
∞
5X
∗
[h], [m] and [s] indicate “hour”, “minute” and “second”.
Screens shown here are only examples. The actual display may vary.
- 88 -
List of LCD monitor displays
■
In playback
1
2
3
9
8
4
5
7
6
1
2
6
7
Recorded date and time
XXhXXmXXs
Cable disconnection warning icon
DMC-FH6
3
4
8
9
∗
5
DMC-FH6
∗
[h], [m] and [s] indicate “hour”, “minute” and “second”.
Screens shown here are only examples. The actual display may vary.
- 89 -
Message displays
Meanings of and required responses to major messages displayed on LCD monitor.
[This memory card cannot be used]
A MultiMediaCard was inserted.
→ Not compatible with the camera. Use a compatible card.
●
[Some pictures cannot be deleted] [This picture cannot be deleted]
●
[No additional selections can be made]
The number of pictures that can be deleted at once has been exceeded.
More than 999 pictures have been set as [Favorite].
The number of pictures allowing [Resize] (multiple settings) at once has been exceeded.
●
●
●
[Please turn camera off and then on again] [System Error]
The lens is not working correctly.
→ Turn on power again.
●
(Consult the dealer or your nearest Service Center if display still remains)
[Some pictures cannot be copied] [Copy could not be completed]
Pictures cannot be copied in following cases.
→ Picture of same name already exists in built-in memory when copying from card.
●
→ Picture taken or edited on a different device.
[Not enough space on built-in memory] [Not enough memory on the card]
There is no space left on the built-in memory or the card. When you copy pictures from the built-in
memory to the card (batch copy), the pictures are copied until the capacity of the card becomes full.
●
[Built-In Memory Error] [Format built-in memory?]
Displayed when formatting built-in memory via computer, etc.
→ Reformat directly using camera. Data will be deleted.
●
[Memory Card Error] [Format this card?]
The card format cannot be used with this camera.
●
[Insert SD card again] [Try another card]
Access to card has failed.
→ Insert card again.
●
Try with a different card.
●
- 90 -
Message displays
[Memory Card Error] [Memory card parameter error]
Card is not of SD standard.
When cards in capacities of 4 GB or more are used, only SDHC or SDXC Memory Cards are
supported.
●
●
[Read Error]/[Write Error] [Please check the card]
Data read has failed.
Data write has failed.
→ Turn off power and remove card, before re-inserting and turning on power again.
Card may possibly be damaged.
Try with a different card.
●
●
●
●
[Motion recording was cancelled due to the limitation of the writing speed of the card]
speed has dropped. If this happens, we recommend backing up the data on the memory card and
●
Motion picture recording may be automatically terminated with certain cards.
●
[A folder cannot be created]
Folder numbers in use have reached 999.
●
[Picture is displayed for 16:9 TV] [Picture is displayed for 4:3 TV]
AV cable is connected to camera.
→ To remove message immediately → Press [MENU/SET].
●
USB connection cable (supplied) is only connected to camera.
→ Message disappears when cable is also connected to another device.
●
- 91 -
Q&A
Troubleshooting
If the problem persists, performing [Reset] in the [Setup] menu may resolve the issue.
(Note that except for some items such as [Clock Set], all settings are returned to their
values from the time of purchase.)
Battery, power
Camera does not work even if power is turned on.
●
The power cuts off during use.
Battery needs recharging.
→ Turn on the power again.
●
●
Recording
Cannot record pictures.
The camera is in Playback Mode.
→ Press the Playback button to switch to recording mode.
●
●
Recorded pictures look white.
Lens is dirty (fingerprints, etc.).
→ Clean lens surface with a soft, dry cloth.
●
●
Recorded pictures are too bright/too dark.
●
2-3 pictures are taken when I press the shutter button just once.
●
Focus not aligned correctly.
Not set to mode appropriate for distance to subject. (Focus range varies according to recording
mode.)
●
Subject outside of focus range.
●
●
Recorded pictures are blurred. Optical Image Stabilizer ineffective.
Shutter speed is slower in dark locations and Optical Image Stabilizer is less effective.
→ Hold camera firmly with both hands, keeping arms close to body.
●
→ Set [Digital Zoom] to [OFF] and [Sensitivity] to [
Recorded pictures appear coarse, or there is interference.
ISO Sensitivity is high, or shutter speed is low.
●
(Default [Sensitivity] setting is [
] – interference may appear with indoor pictures.)
→ Take pictures in brighter locations.
Camera is set to [High Sens.].
(Picture becomes slightly coarser in response to high sensitivity.)
●
- 92 -
Q&A Troubleshooting
Recording (Continued)
Brightness or coloring of recorded picture different from real life.
When recording under fluorescent or LED lighting fixture etc., increasing the shutter speed may
introduce slight changes to brightness and color. These are a result of the characteristics of the light
source and do not indicate a malfunction.
●
Red banding may appear on the LCD monitor or part or the entire
screen may have a reddish tint, when recording or pressing the shutter
button halfway.
This is a characteristic of CCD and may appear if subject contains brighter
areas. Some blurring may occur around these areas, but this is not a fault. This
will be recorded in motion pictures, but not in still pictures.
●
We recommend keeping the screen away from strong light sources such as
sunlight when taking pictures.
●
Motion picture recording stops midway.
With some cards, access display may appear briefly after recording, and recording may end midway.
●
∗
When recording motion picture, use a card rated with an SD speed class of “Class 6” or higher.
●
●
∗
SD speed class refers to a specification for sustained write speeds.
If recording stops even when using a card with speed of “Class 6” or faster, the data writing speed is
Panorama picture recording stops before finishing.
If the pan motion of the camera is too slow, the camera assumes that the operation has been
aborted and stops recording.
●
If the pan motion of the camera is too shaky when it is moved toward the recording direction, the
camera stops recording.
●
→To record panorama pictures, pan the camera in a small circular motion, as in parallel with the
recording direction, at a speed that turning halfway around in approx. 4 seconds (guideline).
The beep volume is low.
The speaker is blocked.
●
LCD monitor
Monitor sometimes shuts off even though power is on.
After recording, monitor shuts off until next picture can be recorded. (Approx. 6 seconds (max.)
when recording to the built-in memory)
●
Brightness is unstable.
Aperture value is set while shutter button is pressed halfway.
(Does not affect recorded picture.)
●
Monitor flickers indoors.
The LCD monitor may flicker for a few seconds after turning on. This is an operation to correct
flicker caused by lighting such as fluorescent lights, LED lights etc. and is not a malfunction.
●
The LCD monitor is too bright or too dark.
●
Black/blue/red/green dots or interference appears. Monitor looks distorted when
touched.
This is not a fault, and will not be recorded on the actual pictures, so there is no need to worry.
●
- 93 -
Q&A Troubleshooting
Flash
No flash emitted.
Flash set to [Forced Flash Off]
The flash is unavailable when using [Burst] (other than [Flash Burst]
[Scenery], [Panorama Shot], [Night Scenery], [Sunset], or [Glass Through] Scene Modes.
●
) or when using
DMC-FH6
●
Multiple flashes are emitted.
●
[Burst] is set to [Flash Burst]
●
DMC-FH6
Playback
Pictures have been rotated.
[Rotate Disp.] is set to
→ For full-screen display without picture rotation, set [OFF].
.
●
Cannot view pictures.
Press the Playback button.
No pictures in built-in memory or card (pictures are played from card if inserted, from built-in
memory if card is not inserted).
●
●
Camera set to [Filtering Play].
●
Folder/file number displayed as [-]. Picture is black.
Picture edited on computer or taken with a different device.
Battery removed immediately after picture taken, or picture taken with low battery.
●
●
The Playback volume and beep volume are low.
The speaker is blocked.
●
Incorrect date displayed in Calendar Playback.
Picture edited on computer or taken with a different device.
(Incorrect date may be displayed in Calendar Playback on pictures copied to computer and then
back to camera, if computer and camera dates differ.)
●
●
White round spots like soap bubbles appear on the recorded picture.
If you take a picture with the flash in a dark place or indoors, white round spots may
●
appear on the picture caused by the flash reflecting particles of dust in the air. This is
not a fault. A characteristic of this is that the number of round spots and their position
differ in every picture.
[Thumbnail is displayed] is shown on the screen.
The still pictures may have been recorded with another device. If so, they may be displayed with
poor picture quality.
●
- 94 -
Q&A Troubleshooting
Playback (Continued)
Blackened red areas in recorded pictures.
When digital red-eye correction (
colored areas with red areas inside, the digital red-eye correction function may blacken the red
areas.
,
) is operating, if a subject is recorded that has skin-
●
→ We recommend setting the Flash Mode to
,
or , or [Red-Eye Removal] to [OFF] before
recording.
The sound of recorded motion pictures is not audible.
Be sure not to block the microphone with your fingers when recording motion pictures.
●
The sound of the recorded motion pictures sometimes breaks up.
This unit automatically adjusts the aperture during motion picture recording. At such times, the
sound may break up. This is not a malfunction.
●
Motion pictures recorded on this camera cannot be played on other devices.
Motion pictures (Motion JPEG) recorded with this camera may not be played on digital cameras of
●
other manufacturers. Additionally, motion pictures recorded with this camera cannot be played on
Panasonic LUMIX digital cameras sold before July 2008. (However, motion pictures recorded with
LUMIX digital cameras sold before this date can be played on this camera.)
TV, computer, printer
No image appear on TV. Image blurred or not colored.
The television has not been switched to auxiliary input.
●
●
TV screen display different to LCD monitor.
Aspect ratio may be incorrect or edges may be cut off with certain televisions.
●
Cannot play motion pictures on TV.
Card is inserted into TV.
●
→ Connect the camera to the TV with the AV cable, and then access playback mode on the camera.
Picture is not displayed on full TV screen.
●
Cannot send pictures to computer.
Check whether computer has recognized camera.
●
●
●
Computer does not recognize card (only reads built-in memory).
Disconnect USB connection cable and reconnect with card in place.
●
- 95 -
Q&A Troubleshooting
TV, computer, printer (Continued)
The card is not recognized by the computer.
(You are using an SDXC Memory Card.)
Make sure your computer supports SDXC memory cards.
http://panasonic.net/avc/sdcard/information/SDXC.html
●
When you insert a card, a message will be displayed requesting you to format the card, but do not
format it.
If [Access] remains displayed on the LCD monitor, turn off the camera and then disconnect the USB
cable.
●
●
Uploading to YouTube or Facebook cannot be performed properly.
→ Confirm that the login information (login ID, user name, e-mail address and password) is correct.
→ Confirm that the PC is connected to the Internet.
→ Confirm that the resident software (such as anti-virus software and the firewall, etc.) is not
blocking access to YouTube or Facebook.
→ Check the YouTube or Facebook site.
Cannot print when connecting to printer.
Printer is not compatible with PictBridge.
●
●
Cannot print the date.
Make date printing settings before printing.
→ With supplied software: Select “with dates” within print settings.
●
●
Edges cut off pictures when printing.
Release any trimming or edgeless printing settings on printer before printing.
(Consult printer operating manual.)
●
The pictures were recorded in
→ If printing in shop, check if 16:9 sizes can be printed.
aspect ratio.
●
- 96 -
Q&A Troubleshooting
Others
Menu not displayed in desired language.
●
Camera rattles if shaken.
This sound is made by the lens movement and is not a fault.
●
Red lamp illuminated when pressing shutter button halfway in dark locations.
●
AF Assist Lamp is not illuminated.
[AF Assist Lamp] is set to [OFF].
Not illuminated in bright locations.
●
●
Camera is hot.
Camera may become a little warm during use, but this does not affect performance or quality.
●
Lens makes a clicking noise.
When brightness changes, the lens may make a clicking noise and the monitor brightness may also
change, but this is due to aperture settings being made.
(Does not affect recording.)
●
Clock is incorrect.
Camera has been left for a long period.
●
When using zoom, picture becomes slightly warped and the edges of the subject
become colored.
Pictures may be slightly warped or colored around the edges, depending on the zoom ratio, but this
is not a fault.
●
File numbers are not recorded in sequence.
●
File numbers have jumped backwards.
Battery was removed/inserted with power on.
(Numbers may jump backwards if folder/file numbers are not correctly recorded.)
●
When the camera is left alone, the slide show is suddenly displayed.
This is the [Auto Demo] to introduce the features of the camera.
●
- 97 -
Usage cautions and notes
When in use
Camera may become warm if used for long periods of time, but this is not a fault.
Keep this unit as far away as possible from electromagnetic equipment (such as microwave
ovens, TVs, video games etc.).
●
●
• If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted
by electromagnetic wave radiation.
• Do not use this unit near cell phones because doing so may result in noise adversely affecting the
pictures and/or sound.
• Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields created
by speakers or large motors.
• Electromagnetic wave radiation generated by microprocessors may adversely affect this unit,
disturbing the pictures and/or sound.
• If this unit is adversely affected by electromagnetic equipment and stops functioning properly, turn
this unit off and remove the battery or disconnect AC adaptor (for dealer display purpose only).
Then reinsert the battery or reconnect AC adaptor and turn this unit on.
Do not use this unit near radio transmitters or high-voltage lines.
• If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound may
be adversely affected.
Do not keep objects that may be influenced magnetically close to the speaker.
• Magnetized objects such as bank cards, commuter passes, watches, may be adversely affected
by the magnetic influence of the speaker.
Do not extend the supplied cord or cable.
Do not allow camera to come into contact with pesticides or volatile substances (can cause surface
damage or coating to peel).
●
●
●
Never leave the camera and the battery in a car or on a car hood in the summer.
It may cause leakage of the battery electrolyte, a generation of heat, and may cause a fire and the
battery to burst due to the high temperature.
●
Caring for your camera
To clean your camera, remove the battery, and wipe with a soft, dry cloth.
Use a damp cloth to remove stubborn stains, before wiping with a dry cloth.
Do not use benzene, thinners, alcohol, or kitchen detergent, as these may damage the outer casing
and finish of the camera.
●
●
If using a chemically-treated cloth, read the supplied instructions carefully.
●
When not using for a while
Turn off camera power before removing battery and card (ensure that battery is removed to prevent
damage through over-discharge).
●
Do not leave in contact with rubber or plastic bags.
Store together with a drying agent (silica gel) if leaving in drawer, etc. Store batteries in cool (15 °C
- 25 °C (59 °F - 77 °F)) places with low humidity (40%RH - 60%RH) and no major temperature
changes.
●
●
Charge battery once per year and use completely before storing again.
●
- 98 -
Usage cautions and notes
Memory cards
To prevent damage to cards and data
• Avoid high temperatures, direct sunlight, electromagnetic waves, and static electricity.
• Do not bend, drop, or expose to strong impacts.
●
• Do not touch connectors on reverse of card or allow them to become dirty or wet.
When disposing of/transferring memory cards
• If using the “format” or “delete” functions on your camera or computer, this only changes the file
management information, and does not completely delete the data from within the memory card.
When disposing of or transferring your memory cards, we recommend physically destroying the
memory card itself, or using commercially available computer data erasing software to completely
delete the data from the card. Data within memory cards should be managed responsibly.
●
LCD Monitor
Do not press hard on the LCD monitor. This may cause uneven display and damage the monitor.
●
In cold climates or other situations when the camera becomes cold, the LCD monitor may be slightly
less responsive than normal immediately after startup. Normal brightness will return once the
internal components have warmed up.
●
Extremely high precision technology is employed to produce the LCD monitor screen. However
there may be some dark or bright spots (red, blue or green) on the screen. This is not a
malfunction. The LCD monitor screen has more than 99.99% effective pixels with a mere 0.01% of
the pixels inactive or always lit. The spots will not be recorded on pictures on the built-in memory
or a card.
About charging the battery
The time required for charging varies depending on conditions of battery usage. Charging takes
●
longer at high or low temperatures and when the battery has not been used in some time.
Battery will be warm during charging and for some time thereafter.
Battery will run out if not used for long periods of time, even after being charged.
Do not leave any metal items (such as clips) near the contact areas of the power plug.
Otherwise, a fire and/or electric shocks may be caused by short-circuiting or the resulting heat
generated.
●
●
●
Frequently charging up battery is not recommended.
(Frequently charging battery reduces maximum usage time and can cause battery to expand.)
Do not disassemble or modify the charger.
If available battery power is significantly reduced, battery is reaching end of lifespan. Please
purchase a new battery.
●
●
●
When charging:
●
• Remove any dirt on connectors of charger and battery with dry cloth.
• Keep at least 1 m (3.3 feet) away from AM radio (may cause radio interference).
• Noises may be emitted from inside of charger, but this is not a fault.
• After charging, remove the charger from the wall socket, and then remove the battery from the
charger (up to 0.1 W consumed if left in place).
Do not use a damaged or dented battery (especially connectors), e.g. by dropping (can cause
faults).
●
- 99 -
Usage cautions and notes
Lens
If lens is dirty:
●
Images may appear slightly white if lens is dirty (fingerprints, etc.). Turn the power on, hold the
extracted lens barrel with your fingers, and gently wipe the lens surface with a soft, dry cloth.
Do not leave the lens exposed to direct sunlight.
Do not touch the lens barrier, as this may damage lens. Be careful when removing camera from
bag, etc.
●
●
When using a tripod or unipod
Do not apply excessive force or tighten screws when they are crooked. (This may damage the
camera, screw hole, or label.)
●
Ensure that the tripod is stable. (Refer to the tripod instructions.)
You may not be able to remove the card or the battery when using a tripod or unipod.
●
●
Personal Information
If birthdays are set in [Baby] Mode, keep in mind that the camera and recorded pictures will contain
personal information.
Disclaimer
●
• Data containing personal information can be altered or lost due to malfunction, static electricity,
accidents, breakdowns, repairs, or other operations.
Panasonic will not be liable for any damage that occurs, direct or indirect, as a result of the
alteration or loss of data containing personal information.
When ordering repairs or transferring/disposing of the camera
●
• Remove the memory card from the camera.
• When ordering repairs, the built-in memory and other settings may be returned to the initial
purchase state.
• If the above operations cannot be performed because of a camera malfunction, consult with the
dealer or nearest Service Center.
When transferring or disposing of your memory card, see “When disposing of/transferring
memory cards” in the previous section.
- 100 -
• SDXC Logo is a trademark of SD-3C, LLC.
• QuickTime and the QuickTime logo are trademarks or
registered trademarks of Apple Inc., used under license
therefrom.
• Mac and Mac OS are trademarks of Apple Inc., registered in
the U.S. and other countries.
• Windows and Windows Vista are either registered trademarks
or trademarks of Microsoft Corporation in the United States
and/or other countries.
• YouTube is a trademark of Google Inc.
• This product uses “DynaFont” from DynaComware Corporation.
DynaFont is a registered trademark of DynaComware Taiwan
Inc.
• Other names, company names, and product names printed in
these instructions are trademarks or registered trademarks of
the companies concerned.
|