CD-RECEIVER
KDC-BT40U
KDC-BT30
INSTRUCTION MANUAL
© B64-4535-00/00 (EW/E0)
Before Use
Notes
2WARNING
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
To prevent injury or fire, take the following
precautions:
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
• The characters which can be displayed by this unit
are A-Z 0-9 @ “ ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel
the Demonstration mode. Refer to <Exit of the
Demonstration Mode> (page 5).
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
Handling CDs
¤
• Do not touch the recording surface of the CD.
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
About the Terminals of the Unit and
Faceplate
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
•
To prevent deterioration, do not touch the terminals of the
unit and faceplate with your fingers.
•
If the terminals on the unit or faceplate get dirty, wipe them
with a clean soft dry cloth.
CDs that cannot be used
Lens Fogging
• CDs that are not round cannot be used.
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-R/
CD-RW recorder instruction manual.)
• 3 inch CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
English
|
3
Component names and functions
1
2
3
4
5
KDC-BT30
15 14 13 12 11
10
9
8
7
6
7
1 Release button
p [4] / [¢] button
The faceplate of the unit can be detached and
taken with you, helping to deter theft. Refer to
<Removing the Faceplate> (page 19).
To select a station, song and setting items.
q Microphone
The microphone for the hands free phone is built
in. When your voice cannot be recognized due
to the low microphone volume, noises or echo
in the vehicle. Adjust the microphone settings
by “MIC GAIN”, “NR LEVEL” and “EC LEVEL” of
<Bluetooth Setup> (page 20).
2 [SRC] button
To turn on this unit and select the Source.
To turn off this unit (press the button at least 1
second).
3 Disc slot
When inserted a disc (label side up), the source is
switched automatically and a song starts playing.
w [VOL] knob
To adjust volume.
Enters function setting mode and setting item
(turn and press the knob). Refer to <Function
Setting Operation> (page 5) for details.
4 Display window
5 [0] button
To eject the disc.
e [BAND] button
To select the remove mode, and remove the USB
device or an iPod (press the button at least 2
seconds or more).
To select the receiving band, the folder for audio
file.
r [
] button
6 USB Terminal: KDC-BT40U only
To return to previous item.
When connecting, open up the USB terminal lid. A
USB device or an iPod can be connected.
t [ ] button
To enter the music search mode.
To enter the PTY and Traffic information mode.
To enter the dialing mode.
7 Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm ø).
•
Use the mini-plug cable which is stereo type and does
not have any resistance.
8 [1] – [6] button
To recall the memorized station.
Switches the play mode between music discs,
audio files, and iPod.
9 [VOICE] button
To make a voice dialing call.
To change text scroll. (press the button at least 1
second)
|
4
KDC-BT40U/KDC-BT30
General operation
Before Using
Function Setting Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
Exit of the Demonstration Mode
Turn off the demonstration mode when you use it
for the first time after installation.
1 Select the source
1 Press the [VOL] knob to quit the demonstration
mode when the messages “CANCEL DEMO” and
“PRESS”, “VOLUME KNOB” are displayed (approx.
15 seconds).
Press the [SRC] button.
Function items vary from source to source. For a list
of the function items. Refer to <Function Item List>
(Page 30).
2 Turn the [VOL] knob to select “YES” and press the
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
”FUNCTION” is displayed.
[VOL] knob.
⁄
•
The demonstration can be set or cancel using
<Demonstration Mode Setting> (page 18).
3 Select your desired function item
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired function
item is selected.
Common Operation
Power and source select
Turns the power ON by pressing the [SRC]
button.
⁄
Press the [ ] button to return to the previous
item.
Pressing [SRC] button each time switches
between sources.
Tuner (“TUNER”) ➜ USB* or iPod* (“USB” or
“iPod”) ➜ CD (“CD”) ➜ Auxiliary input (“AUX”) ➜
Standby (“STANDBY”)
Example:
ꢂ
ꢁ
ꢀ
ꢂ
ꢁ
AUDIO CONTROL
BASS BOOST
ꢀ
ꢀ
[VOL]
[VOL]
ꢂ
Keeping pressing the [SRC] button at least 1
second turns the power OFF.
ꢁ
DETAILED SET
DETAIL SET
SUPREME SET
⁄
DISP SELECT
SETTINGS
•
•
* Function is KDC-BT40U only.
When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
The source “CD” and “iPod” can be selected when each
source is ready to play.
In this manual, the above selection is indicated as
Select “AUDIO CONTROL” (“AUDIO CTRL”) >
“DETAILED SET” (“DETAIL SET”) > “SUPREME SET”.
(“ ”) encloses a display appearing on the KDC-BT30.
It is shown only if it differs from the one appearing
on the KDC-BT40U.
•
Volume
Turning the [VOL] knob adjusts the sound
volume.
4 Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
5
Music Disc/Audio File/iPod Operation
[SRC] [VOL]
Disc slot
[ꢀ]
CA-U1EX
•
•
CA-U1EX (optional accessory) is
required to connect a USB device.
KCA-iP101 (optional accessory) is
required to connect an iPod.
ꢁ E
[ ] / [ ]
[
] [
]
[BAND]
[1] [6]
USB Terminal
—
Basic Operation
Play function
Playing Disc
Scan play
Insert a disc into the disc slot (label side up).
When inserted, the source is switched
Press the [2] button.
Successively plays the intro of the music in the disc
automatically and a song starts playing.
or folder.
When a disc is inserted, the “IN” indicator lights up.
When Scan Play is turned on, “TRACK SCAN”/ “TRAC
SCAN”/ “FILE SCAN” is displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
Playing USB device or iPod (KDC-BT40U only)
Connect a USB device or iPod to the USB terminal.
When connected, the source is switched
automatically and a song starts playing.
⁄
Pause and play
Press the [6] button to pause or resume
playback (track or file).
•
The Scan play operation cannot be performed while
iPod is playing.
Random play
Press the [3] button.
Randomly plays the music in the disc or folder.
When Random Play is turned on, “DISC RANDOM”/
“FOLDER RANDOM”/“FOLD RANDOM” is displayed.
Press this button again cancels the Random play.
Folder select
Press the [BAND] button switches a folder.
The iPod can be operated only when a category
has been selected in the search mode.
Song select
Press the [4] or [¢] button selects a song
Repeat play
Press the [4] button.
Switches between Track Repeat (“TRACK REPEAT”/
“TRAC REPEAT”) and OFF (“REPEAT OFF”) when
pressed while playing a CD.
(track or file).
Fast reverses or forwards the music while
pressing the [4] or [¢] button.
(No sound is output while playing audio file.)
Ejecting Disc
Switches between File Repeat (“FILE REPEAT”),
Folder Repeat (“FOLDER REPEAT”/“FOLD REPEAT”),
and OFF (“REPEAT OFF”) when pressed while
playing an audio file.
Press the [0] button ejects a disc.
You can eject the disc for 10 minutes after
switching off the engine.
Removing USB device or iPod
Press the [0] button for at least 2 seconds can
be entered to the USB Remove mode (“USB
REMOVE” is displayed) and the USB device, iPod
can be removed safely.
Selecting CD, USB or iPod source
Press the [SRC] button.
Select the “CD”/“USB” or “iPod” display.
|
6
KDC-BT40U/KDC-BT30
Function of KDC-BT40U with iPod
Cancelling the Music Search mode
Press the [
] button for at least 1 second.
All Random
⁄
All songs in iPod are played at random.
•
Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs in
the list which is selected. Set the ratio with “SKIP SEARCH”
of <Audio File/ iPod Setting> (page 9). Keep pushing the
Press the [3] button for at least 1 second.
Pressing the button toggles the setting between
All random play on (“ALL RANDOM”) and off
(“RANDOM OFF”). Press this button again cancels
the Random play.
[4] or [¢] button for 3 seconds or longer skips songs
at 10% regardless of the setting. (KDC-BT40U only)
* This operation is effective only for the files registered in
the database created with KENWOOD Music Editor.
•
⁄
•
•
•
The time required to turn on the all random function
may become longer depending on the number of songs
in iPod.
Function of KDC-BT40U with iPod
Turning on the all random function changes the iPod
browse item to “SONGS”. This browse item will not be
changed even if the all random function is turned off.
If the browse item is changed to search for music while
the all random function is on, the all random function is
turned off and the songs in the browse item are played
at random.
Music Search for iPod
Searching for the song (in iPod) you want to play.
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
2 Search for music
Operation type
Move between items
Skip Search
Select an item
Return to previous item Press the [ ] button.
Function of Audio file/ CD source
Operation
Turn the [VOL] knob.
Music Search
Press the [
Press the [VOL] knob.
4] or [¢] button.
Selecting the music you want to listen to from the
device or media being played now.
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
Return to Top menu
Search by Alphabet
Press the [BAND] button.
Press the [ ] button. Refer to <Alphabet
Search> (page 8).
Displays the current Audio file name.
Cancelling the Music Search mode
2 Search for music
Press the [
] button for at least 1 second.
Audio file
⁄
•
Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs in
the list which is selected. Set the ratio with “SKIP SEARCH”
of <Audio File/ iPod Setting> (page 9). Keep pushing the
Operation type
Operation
Move between folders/ Turn the [VOL] knob.
files
Skip Search*
Select of folder/file
Press the [
Press the [VOL] knob.
4] or [¢] button.
[4] or [¢] button for 3 seconds or longer skips songs
at 10% regardless of the setting.
If no characters included in a song name can be
displayed, the browse item name and digits are
displayed.
Return to previous folder Press the [ ] button.
Return to root folder Press the [BAND] button.
•
“<” or “>” beside the displayed folder name
indicates that this folder is preceded or followed by
another folder.
Items
Playlists
Artists
Albums
Songs
Display
Items
Podcasts
Genres
Display
“PLIST***”
“ART***”
“ALB***”
“PRGM***”
“PDCT***”
“GEN***”
“COM***”
CD source
Composers
Operation type
Move between track
Select of track
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Return to first track
Press the [BAND] button before selecting
a track.
English
|
7
Music Disc/Audio File/iPod Operation
Function of KDC-BT40U with iPod
You can select the song to play by referring to
<Music Search for iPod> (page 7).
Alphabet Search
2 Register the song
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected browse item
(artist, album, etc.).
Press the [5] button for at least 2 seconds.
“## STORED (Registration number)” is displayed.
You can register up to 10 songs.
⁄
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
•
Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod, ”NO
INFO” appears and then ”MPLIST DELETE” appears. To
delete the Playlist, turn the [VOL] knob to select “YES”
and then press the [VOL] knob.
2 Enter Alphabet Search mode
Press the [ ] button.
“SEARCH <_ _ _>” is displayed.
•
The song displayed in the Music Search mode can be
registered in the same manner. For how to use the music
search function, refer to <Music Search for iPod> (page
7).
3 Select the character to be searched for
Operation type
Operation
•
•
If you attempt to register the eleventh song, ”MEMORY
FULL” appears and you cannot register it accordingly. To
register the song, delete an unnecessary song.
Do not register Podcasts. Songs you do not want to
register may be registered, or playback may not be
carried out correctly.
Select the characters
Turn the [VOL] knob.
Move the cursor to the Press the [
enter character position
4] or [¢] button.
You can enter up to 3 characters.
4 Determine the selected character
Playing the Song in the Playlist
Press the [VOL] knob.
Start search. When the search is completed,
the music search mode is selected again at the
selected character position.
1 Display the Playlist
Press the [5] button.
“MY PLAYLIST” is displayed.
Cancelling the Alphabet Search mode
2 Play the song in the Playlist
Press the [
] button for at least 1 second.
Turn the [VOL] knob to select the song you
want to play, and then press the [VOL] knob.
⁄
•
The time of Alphabet search may become long
⁄
depending on the number of songs or number of
playlists in iPod.
•
Turning the power OFF stops playing the song in the
Playlist.
•
To search for a character other than A to Z and 0 to 9, enter
“*” at the first character position. In this case, you cannot
enter any character at the second and third character
positions.
•
If a song does not end with at least 1 second of silence,
the ending part of the song may not play out.
Deleting a Song from the Playlist
•
If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
1 Turn the [VOL] knob to display the song you
want to delete, and then press the [VOL] knob
for at least 2 seconds.
2 Turn the [VOL] knob to select ”ONE” or “ALL”,
and then press the [VOL] knob.
Function of KDC-BT40U with iPod
Selecting “DELETE ALL” deletes all songs.
My Playlist for iPod
3 Turn the [VOL] knob to select ”YES”, and then
press the [VOL] knob.
“COMPLETED” is displayed.
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
⁄
Registering Songs in the Playlist
•
You can also delete all songs from the Playlist by
selecting “MPLIST DELETE” described in <Audio File/iPod
Setting> (page 9).
1 Play the song you want to register
Press the [BAND], [4], and [¢] button.
|
8
KDC-BT40U/KDC-BT30
Function of KDC-BT40U
Function of remote control (Optional Accessory)
Audio File/ iPod Setting
Direct Music Search
You can select following setting items.
Searching the music by entering the track number.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
1 Enter Direct Music Search mode
Press the [DIRECT] button.
2 Enter the music number
2 Select the function item
Press the number buttons.
Turn the [VOL] knob and press it when the
desired item is displayed.
3 Search the music
Press the [4] or [¢] button.
Select “SETTINGS” > Function item.
Cancelling Direct Music Search
Function item
“SKIP SEARCH”
Selectable setting/item
Press the [
] button.
The number of songs to be skipped is
determined by the ratio of the total number of
songs in the list which is selected. (iPod and
KENWOOD Music Editor File only)
0.5%/1%/5%/10%
⁄
•
Direct Music Search cannot be performed during playing
of iPod, “Music Editor” media, Random play, or scan play.
“MPLIST DELETE”
Deletes the saved My Playlist. <My Playlist for
iPod>(page 8) (iPod only)
NO/YES
(Factory setting: Underlined)
3 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
When select “MPLIST DELETE”:
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Deletes the saved My Playlist.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
Function of KDC-BT40U with iPod
iPod Control by Hand Mode
Allowing you to operate iPod with the control on
the iPod.
Press the [1] button.
Pressing the button toggles the setting between
iPod control by hand mode on (“HANDS ON”) and
off (“HANDS OFF”).
⁄
•
•
•
In the iPod Control by hand mode, iPod cannot be
operated using this unit.
This mode is not compatible with music information
display. The display will show “iPod MODE”.
iPod can be operated when it conforms to the iPod
control function.
English
|
9
Tuner Operation
Tuner Setting
[SRC] [VOL]
You can select following Tuner Setting items.
1 Select the TUNER source
Press the [SRC] button.
Select the “TUNER” display.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
ꢁ
E
]
[
] [
]
[BAND]
[
] / [
—
[1] [6]
3 Select the function item
Basic Operation
Turn the [VOL] knob and press it when the
desired item is displayed.
Selecting Tuner source
Press the [SRC] button.
Select “SETTINGS” > Function item.
Select the “TUNER” display.
Function item Selectable setting/item
“LOCAL SEEK”
Only stations whose reception is good are searched
in auto seek tuning. (FM band only)
OFF/ON
Selects the tuning mode of the radio.
AUTO1: Automatic search for a station.
AUTO2: Search in order of the stations in the Preset
memory.
Selecting the Receiving Band
Press the [BAND] button.
Each time you press the button, the receiving band
alternates between the FM1, FM2, FM3 and AM.
“SEEK MODE”
Selecting the Receiving station
Press the [4] or [¢] button.
During reception of stereo stations the “ST”
indicator lights up.
MANUAL: Normal manual tuning control.
“AUTO MEMORY”* Putting stations with good reception in the memory
automatically.
NO/YES
Selecting the preset channel
Press the [1] – [6] button.
“MONO SET”
“NEWS SET”
You can reduce the noise when stereo broadcasts
are received as monaural. (FM band only)
OFF/ON
Automatically receives news bulletin when it starts.
Set the time during which interrupt is to be disabled
after start of another news bulletin.
Changing“NEWS 00M”to“NEWS 90M”turns this
function ON. If news bulletin starts when this
function is ON, “NEWS”is displayed and news is
received. If“20M”is has been set, reception of
another news bulletin will not start for 20 minutes.
The news bulletin volume is the same level that
was set for Traffic Information.
Traffic information
Press the [ ] button for at least 1 second.
Turns ON or OFF the Traffic Information function.
When the function is set to ON, “TI” indicator lights
up.
If traffic bulletin starts when the function is ON,
“TRAFFIC INFO” (“TRAFFIC”) is displayed and traffic
information is received.
OFF/00M — 90M
Station Preset Memory
“AF SET”
When station reception is poor, automatically
switches to the station that is broadcasting the
same program over the same RDS network.
OFF/ON
Putting a station in the memory.
1 Select the frequency to put in the memory
“RDS REGIONAL” Sets whether to switch to the station only in the
Press the [4] or [¢] button.
“RDS REG”
specific region using the“AF”control.
OFF/ON
2 Select the number to put in the memory
“AUTO TP SEEK” When traffic information station reception is poor,
Press the [1] – [6] button for at least 2 seconds.
(“ATP SEEK”)
automatically searches for a station that can be
received better.
OFF/ON
⁄
•
Up to 6 stations with a different band (FM/AM) can be
memorized to the [1] – [6] button according to the
setting of “PRESET TYPE” of <Initial Setting> (page 18).
(Factory setting: Underlined)
|
10 KDC-BT40U/KDC-BT30
4 Make a setting
4 Exit PTY mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [
] button.
⁄
When select “AUTO MEMORY”:
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
•
This function cannot be used during a traffic bulletin or
AM reception.
•
When the selected Program Type is not found, “NO PTY”
is displayed. Select another Program Type.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
5 Exit Function Setting mode
Program Type Preset
Press the [
] button for at least 1 second.
Putting the Program Type in the Preset button
memory and quick recall.
⁄
•
* This setting can be made when “TYPE NORMAL” (“TYPE
NORM”) is selected for the “PRESET TYPE” of <Initial
Setting> (page 18).
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 11).
PTY (Program Type)
2 Preset the Program Type
Press the desired [1] — [6] button for at least 2
seconds.
Selecting the Program Type below and searching
for a station.
Recalling the preset Program Type
Program Type Display
Program Type Display
Speech
Music
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening
Music
“SPEECH”
“MUSIC”
“NEWS”
“AFFAIRS”
“INFO”
Serious Classical “CLASSICS”
1 Enter PTY mode
Other Music
Weather
Finance
“OTHER M”
“WEATHER”
“FINANCE”
Refer to <PTY (Program Type)> (page 11).
2 Recall the Program Type
Press the desired [1] — [6] button.
Children’s programs “CHILDREN”
“SPORT”
Social Affairs
Religion
Phone In
“SOCIAL”
“EDUCATE”
“DRAMA”
“CULTURE”
“SCIENCE”
“VARIED”
“POP M”
“ROCK M”
“EASY M”
“RELIGION”
“PHONE IN”
“TRAVEL”
Changing Language for PTY Function
Travel
Selecting the Program Type display language as
follows.
Leisure
“LEISURE”
“JAZZ”
“COUNTRY”
“NATION M”
“OLDIES”
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Language
English
French
Display
“ENGLISH”
“FRENCH”
“GERMAN”
“FOLK M”
“DOCUMENT”
German
Light Classical
“LIGHT M”
1 Enter PTY mode
•
Speech and Music include the Program type shown
below.
Refer to <PTY (Program Type)> (page 11).
Music: Items in the white letters.
Speech: Items in the black letters.
2 Enter Changing Language mode
Press the [ ] button.
1 Enter PTY mode
3 Select the language
Press the [ ] button.
During PTY mode the “ ” indicator is ON.
(KDC-BT40U only)
Turn the [VOL] knob.
4 Exit Changing Language mode
Press the [VOL] knob.
2 Select the Program Type
Turn the [VOL] knob.
3 Search for the selected Program Type station
Press the [4] or [¢] button.
English
|
11
Operation of Hands-Free Phoning
⁄
[SRC] [VOL]
•
When registering from this unit. Refer to <Registering
Bluetooth Device> (page 21).
•
For details on the Bluetooth cell-phone with the hands-
free function, see <About the Cell-Phone> (page 29).
Making a Call
ꢁ
E
]
—
[
][ ][BAND]
[
] / [
[VOICE] [1] [6]
You can select following dialing method.
Connecting a Bluetooth Device
1 Enter Bluetooth mode
Press the [VOL] knob.
“BT MODE” is displayed.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit. The following
3 steps procedure is necessary.
2 Enter dialing method mode
Press the [ ] button.
“PHONE BOOK” is displayed.
Step 1. Pairing (Registering from Bluetooth
devices)
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing).
3 Select a dialing method
Turn the [VOL] knob and press it when the
desired item is displayed.
1 Turn on this unit.
Display
Overview
Press the [SRC] button.
“PHONE BOOK” Selecting the initial to be searched or name for the
phone book.
2 Start registering this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-3P1” from the list of connected units.
“OUT-CALL”
“IN-CALL”
Calling a number in the outgoing call list.
Calling a number in the incoming call list.
“MISSED CALLS” Calling a number in the missed calls list.
(“MIS-CALL”)
“NUMBER DIAL” Making a call by entering phone number.
3 Enter a PIN code
Operation method of each mode is described
below.
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device. PIN code is set to “0000” as
the default. You can change this code. Refer to
<Registering PIN Code> (page 22).
4 Exit the dialing method mode
Press the [
] button for at least 1 second.
Disconnecting a Call
Press the [SRC] button.
4 By operating the Bluetooth device, start hands-
free connection.
Step 2. Connection
Calling a Number in the Phone Book
If you have registered 2 or more cell-phones, you
need to select one of them. For more details, see
<Selecting the Bluetooth Device You Wish to
Connect> (page 23).
1 Select the Phone Book mode
For how to select dialing method, refer to <Making
a Call> (page 12).
When a cell-phone is connected, the “BT” indicator
lights up.
Select the “PHONE BOOK” display.
2 Select the initial to be searched for
Step 3. Hands-free phoning
Operation type
Move to the next character. Turn the [VOL] knob.
Move to the next row. Press the [BAND] button.
Determine the selected initial. Press the [VOL] knob.
Operation
You can do hand-free phoning when the
connection is made.
|
12 KDC-BT40U/KDC-BT30
3 Select the name
Operation type
Move to the next phone
number.
3 Make a call
• Press the [VOL] knob.
• Press the [OK] button on the remote
controller.
Operation
Turn the [VOL] knob.
Move to the next name.
Press the [4] or [¢] button.
⁄
•
You can input max 25 digits.
4 Make a call
Press the [VOL] knob.
⁄
Make a Voice Dialing Call
•
To use the Phone Book, it must be downloaded to this
unit in advance. Refer to <Downloading the Phone
Book> (page 22).
1 Enter voice recogntion mode
Press the [VOICE] button.
“V-RECG READY” (“VR READY”) is displayed.
•
During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
2 Press the [VOL] knob.
“PB NAME” is displayed.
When a beep is heard, say the name within 2
seconds.
Calling a Number in the Call Log
3 “PN TYPE” is displayed.
1 Select the call log mode
When a beep is heard, say the category name
within 2 seconds.
For how to select dialing method, refer to <Making
a Call> (page 12).
Select the “OUT-CALL” (outgoing call), “IN-CALL”
(incoming call), or “MISSED CALLS” (“MIS-CALL”)
(missed call) display.
4 Make a call
Press the [VOL] knob.
Move to the next phone number
Turn the [VOL] knob.
2 Select a name or phone number
Turn the [VOL] knob.
⁄
3 Make a call
•
If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
voice input. (page 37)
Press the [VOL] knob.
⁄
•
•
Both the name and category require registration of a
voice tag. (page 24)
Audio sound is not output during voice recognition.
•
The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
Registering to the Preset Dial Number
(Preset Memory)
Dial a Number
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dial a number/ Calling a number in the call log/
Calling a number in the Phone Book
1 Select the number dial mode
For how to select dialing method, refer to <Making
a Call> (page 12).
Select the “NUMBER DIAL” display.
2 Enter a phone number
2 Select the number to put in the memory
Operation type
Operation
Press the [1] – [6] button for at least 2 seconds.
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
4
] button.
] button.
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
English
|
13
Operation of Hands-Free Phoning
Speed Dialing (Preset Dial)
Call Waiting
1 Select the number you want to recall from the
memory
Answering Another Incoming Call with the
Current Call Suspended
Press the [1] – [6] button.
1 Press the [VOL] knob.
2 Make a call
2 Turn the [VOL] knob and press it when the
Press the [VOL] knob.
desired item is displayed.
Select “ANSWER”.
⁄
•
You need to register the preset dial number.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
Receiving a Call
Continuing the Current Call
1 Press the [VOL] knob.
Answering a Phone Call
Press the [VOL] knob.
2 Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
Select “REJECT”.
•
The following operations disconnect the line:
- Insert a CD.
Answering the Waiting Call after Terminating
the Current Call
Press the [SRC] button.
- Connect a USB device.
•
The name of the calling party is displayed if it has already
been registered in the Phone Book.
Switching between the Current Call and Waiting
Call
Press the [VOL] knob.
Rejecting an Incoming Call
Press the [SRC] button.
Each pressing of this knob switches the calling
party.
During a Call
Disconnecting a Call
Press the [SRC] button.
Other Functions
Clearing the Disconnection Message
Press the [VOL] knob.
“HF DISCONCT” disappears.
Switching to the Private Mode
Press the [6] button.
Switches between Private talk (“PRIVATE TALK”) and
Hands-free talk each time this button is pressed.
Switching between Display Modes
Press the [ ] button.
Pressing this button each time switches between
⁄
•
Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
your cell-phone to return to the hands-free talk mode.
name and telephone number.
Display of Phone Number Type
(Category)
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
The category items in the Phone Book are displayed
as follows.
Display
“GE”
“HM”
“OF”
Information
General
Home
Office
“MO”
“OT”
Mobile
Other
|
14 KDC-BT40U/KDC-BT30
Audio Adjustments
“SUB-W LEVEL”
You can set subwoofer level.
–15 — 0 — +15
[SRC] [VOL]
“DETAILED SET”
(“DETAIL SET”)
Move to detailed item.
“LPF SUBWOOFER” Selects cut off frequency of subwoofer output.
(“LPF SUB-W”) 85/120/160/THROUGH (OFF) Hz
“SUB-W PHASE” Selects the phase of subwoofer output.
REVERSE (180°)/ NORMAL (0°)
“SUPREME SET” Turns on/off the supreme function.
OFF/ON
[
]
“VOLUME OFFSET” Sets each source’s volume as a difference from
(“VOL OFFSET”) the basic volume.
Audio Control
–8 — 0 (AUX: –8 — 0 — +8)
You can adjust following Audio Control items.
(Factory setting: Underlined)
4 Make a setting
1 Select the source
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [SRC] button.
Select the “TUNER”/“USB” or “iPod”/
“CD”/“AUX” display.
5 Exit Function Setting mode
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
Press the [
] button for at least 1 second.
⁄
• SUPREME:
3 Select the function item
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is
cut off when encoding at low bit rate (less than 128Kbps,
Sampling frequency is 44.1kHz).
Supplementing is optimized by compression format
(MP3, WMA and AAC) and processed according to bit
rate. The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “AUDIO CONTROL” (“AUDIO CTRL”) >
Function item or select “AUDIO CONTROL”
(“AUDIO CTRL”) > “DETAILED SET” (“DETAIL
SET”) > Function item.
Function item
Selectable setting/item
“SUBWOOFER SET” Turns on/off the subwoofer output.
(“SUB-W SET”)
“BASS BOOST”
OFF/ON
Selects bass boost setting mode.
OFF/LV1/LV2 (The indicator turns on according
to the setting.)
“SYSTEM Q”
Switches between the following preset equalizer
curves. “EQ“ indicator is lights when System Q is
set to an EQ mode other than“NATURAL”.
NATURAL/USER/ROCK/POPS/EASY/TOP40/
JAZZ/GAME
For USER: This appears when Bass level, Middle
level, and Treble level are adjusted.
You can set bass level for each source.
–8 — 0 — +8
You can set middle level for each source.
–8 — 0 — +8
You can set treble level for each source.
–8 — 0 — +8
Adjusts left/right speaker balance.
(Left) L15 — 0 — R15 (Right)
Adjusts front/rear speaker balance.
(Rear) R15 — 0 — F15 (Front)
“BASS LEVEL”
“MID LEVEL”
“TRE LEVEL”
“BALANCE”
“FADER”
English
|
15
Display Settings
In Standby/ Auxiliary input source
[SRC] [VOL]
Information
Source name
Clock
Display
“SOURCE NAME”
“CLOCK”
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
[
]
[VOICE]
•
•
•
When you select the clock display, the display setting of
each source will be changed to the clock display.
If the selected display item does not have any
information, alternative information is displayed.
When selecting “FOLDER NAME” while playing with
iPod, names will be displayed depending on currently
selected browsing items.
Display Selection
Changing displayed information on each source
following.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
•
•
If the iPod Control by Hand Mode is set to on while
playing the iPod, “iPod MODE” is displayed.
If all characters cannot be displayed while playing with
iPod, the file number in the list is displayed.
2 Enter Display Select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Information
Music title
Folder name
File name
Display
“TITLE***”
“FOLDER***”
“FILE***”
Select “DISP SELECT”.
3 Select the text
Turn the [VOL] knob and press it when the
desired item is displayed.
Text Scroll
In Tuner source
Scrolling the displayed File name, Song title, etc.
Information
Display
Program Service name or Frequency
“FREQUENCY/PS”
(“FREQ/PS”)
Press the [VOICE] button for at least 1 second.
Radio text, Program Service name or Frequency “RADIO TEXT”
Clock
“CLOCK”
In Audio file/ iPod source
Information
Display
Music title & Artist name
“TITLE/ARTIST”
(“TITLE”)
Album & Artist name
“ALBUM/ARTIST”
(“ALBUM”)
Folder name
File name
Play time & Music number
Clock
“FOLDER NAME”
“FILE NAME”
“P-TIME”
“CLOCK”
In CD source
Information
Disc title
Track title
Play time & Track number
Clock
Display
“DISC TITLE”
“TRACK TITLE”
“P-TIME”
“CLOCK”
|
16 KDC-BT40U/KDC-BT30
Display Setting
Auxiliary Input Display Setting
You can select following Display Setting items.
Selecting the display when changing to Auxiliary
input source.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
1 Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
2 Select the function item
Turn the [VOL] knob and press it when the
desired item is displayed.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
Select “SETTINGS” > “DISPLAY” > Function item.
Function item
“DIMMER SET”
Selectable setting/item
Adjusts the brightness of the display according to
the surrounding illumination.
3 Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SETTINGS” > “AUX NAME SET” (“AUX
NAME”).
OFF/ON
“TEXT SCROLL”
Scrolling the displayed File name, Song title, etc.
Selecting AUTO scrolls them automatically.
AUTO/MANUAL
You can display the connection status, signal
strength, and battery level of cell-phone.
HF-CON: Connection status.
BATT: Battery level of cell-phone.
SIGNAL: Signal strength of cell-phone.
• Data are not displayed if information cannot be
obtained from the cell-phone.
• Since the number of steps of this unit is
different from that of the cell-phone, the
statuses displayed on this unit may discord
from those displayed on the cell-phone.
The presently selected Auxiliary input display is
displayed.
“BT DVC STATUS”
(“DVC STATUS”)
4 Select the Auxiliary input display
Turn the [VOL] knob and press it when the
desired item is displayed.
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
(Factory setting: Underlined)
3 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
17
Other Functions
Release button
Demonstration Mode Setting
[SRC] [VOL]
Turning the demonstration mode ON/OFF.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
2 Select Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
[
]
Select “DEMO MODE”.
Clock Adjustment
3 Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
1 Turn on this unit.
Press the [SRC] button.
Select “ON” or “OFF”.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
3 Cancelling “TIME SYNC” mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Initial Setting
You can select following Initial Setting items.
Select “SETTINGS” > “CLOCK” > “TIME SYNC”.
Turn the [VOL] knob to select “OFF”, and then
press the [VOL] knob.
1 Select the Standby source
Press the [SRC] button.
Display
Overview
Select the “STANDBY” display.
“CLOCK ADJUST” Sets the clock. You can do this adjustment when
“TIME SYNC”is set to“OFF”.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
“TIME SYNC”
Synchronizing the RDS station time data and this
unit’s clock.
3 Select the function item
OFF/ON
Turn the [VOL] knob and press it when the
desired item is displayed.
(Factory setting: Underlined)
4 Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SETTINGS” > “CLOCK” > “CLOCK
ADJUST” (“CLOCK ADJ”).
Select “INITIAL SET” > Function item.
Function item Selectable setting/item
“PRESET TYPE” TYPE NORMAL (TYPE NORM):
1 station can be assigned to 1 preset button in each
of 4 bands (FM1, FM2, FM3, and AM), i.e., a total of
24 stations (6 stations x 4 bands) can be preset.
TYPE MIX:
The hour display blinks
5 Adjusting Clock
A total of 6 stations can be assigned to a total of 6
preset buttons regardless of band (FM1, FM2, FM3,
and AM). You can recall a preset station without
switching between bands.
Turn the [VOL] knob to set the hours and press
it when to finish the hour adjusting.
The minute display blinks.
“KEY BEEP”
Setting the operation check sound (beep sound)
on/off.
OFF/ON
Turn the [VOL] knob to set the minutes and
press it when to finish the minute adjusting.
6 Exit Function Setting mode
Press the [
] button for at least 1 second.
|
18 KDC-BT40U/KDC-BT30
“RUSSIAN SET” When this is set to ON, the following character
strings are displayed in Russian. (Folder name/ File
name/ Song title/ Artist name/ Album name)
OFF/ON
Removing the Faceplate
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
Detach the faceplate
Press the Release button.
Reattaching the Faceplate
Refer to the following diagram when
reattaching the faceplate.
“P-OFF WAIT”
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues. Using
this setting can save the vehicle’s battery power.
– – –: Power OFF Timer function is OFF.
20M: Turns the power OFF after 20 minutes.
40M: Turns the power OFF after 40 minutes.
60M: Turns the power OFF after 60 minutes.
“BUILT-IN AUX” When this is set to ON, AUX source can be selected.
(“BUILTIN AUX”) ON1: Outputs the sound of external unit connected
to the AUX terminal when switched to AUX
source.
¤
•
After pressing the Release button, detach the faceplate
immediately. If the faceplate is left attached, it can fall
due to vibration and so on.
ON2: Activates the attenuator function when
turning on the power with AUX source
selected. Cancel the attenuator function
by turning the volume knob clockwise
when listening to the audio of the external
equipment.
•
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
•
•
Keep the faceplate in its faceplate case while detached.
Do not place the faceplate (and the faceplate case)
in areas exposed to direct sunlight, excessive heat or
humidity. Also avoid places with too much dust or the
possibility of water splashing.
OFF: Disables the selection of AUX source. Set to
OFF when not using the AUX terminal.
“CD READ”
Sets the method for reading CD.
1: Automatically distinguishes between audio file
disc and music CD when playing disc.
2: Forces playing as music CD.
“SWITCH PREOUT” Switches the preout between rear output (“REAR”)
(“SWITCH PRE”) and subwoofer output (“SUB-W”)
REAR/SUB-W
How to Reset Your Unit
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when
the Reset button is pressed.
“SP SELECT”
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
SP OFF: OFF
SP 5/4: For 5 & 4 in. speaker
SP 6*9/6: For 6 & 6x9 in. speaker
SP OEM: For the OEM speaker
Display the firmware version and update the
firmware.
MEDIA USB: Select a USB device.
MEDIA CD: Select CD.
1 Release the faceplate lock so that it can be
removed.
Refer to <Removing the Faceplate> (page 19).
“F/W UP”
2 Press the Reset button and reattaching the
faceplate.
(With the KDC-BT30, CD is selected.)
For how to update the firmware, access our web
site.
(Factory setting: Underlined)
Reset button
4 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
19
Bluetooth Setup
“AUTO ANSWER” This function automatically answers (responds
to) a call after lapse of the preset time interval
for automatic answer.
[SRC] [VOL]
OFF: Does not answer the phone call
automatically.
0: Automatically answers the phone call at once.
1 – 8 –99: Automatically answers the phone
call after lapse of 1 – 99 seconds.
“BT SP SELECT” You can specify the audio output speakers.
ꢁ
E
]
[
] / [
[
] [
]
(“BT SP SEL”)
Select the speaker which is further from the
microphone in order to prevent howling or
echoes.
Bluetooth Setup
SP FRONT: Outputs audio from the front-left and
front-right speakers.
You can select following Bluetooth Setup items.
SP ALL: Outputs audio from the all speakers.
You can output a beep from the speaker when a
call comes in.
“CALL BEEP”
1 Enter Bluetooth mode
Press the [VOL] knob.
“BT MODE” is displayed.
ON: Beep is heard.
OFF: Beep is canceled
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
“BT F/W UPDATE” Display the firmware version and update the
(“BT UPDATE”) firmware. Refer to <Displaying the Firmware
Version> (page 22).
“MIC GAIN”
Adjust the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to“+”increases the voice volume.
–3 – 0 – +3
3 Select the function item
Turn the [VOL] knob and it when the desired
item is displayed.
“NR LEVEL”
Reduce the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to“+”increases the
noise reduction.
Select “SETTINGS” > Function item or select
“SETTINGS” > “DETAILED SET” (“DETAIL SET”) >
Function item.
Function item
Selectable setting/item
–3 – 0 – +3
“PHONE SELECT”
(“PHONE SEL”)
Selects a cell-phone connection. Refer to
<Selecting the Bluetooth Device You Wish to
Connect> (page 23).
“EC LEVEL”
Adjust the level of echo cancellation. Setting to
“+”increases the echo cancel reduction.
–2 – 0 – +2
“SMS DOWNLOAD” Download a short message. Refer to
(Factory setting: Underlined)
(“SMS DL”)
“SMS INBOX”
<Downloading the SMS> (page 23).
Display the received short message. Refer to
<SMS (Short Message Service)> (page 24).
Registers voice for voice recognition and
voice to select the Phone number category in
Phone book. Refer to <Adding a Voice Dialing
Command> (page 24) and <Setting a Voice
Command for Category> (page 25).
4 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
“VOICE TAG”
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
“DETAILED SET”
(“DETAIL SET”)
Move to detailed item.
“DEVICE REGIST” Registers a Bluetooth device (pairing).
(“DVC REGIST”) Refer to <Registering Bluetooth Device>
(page 21).
“S-DVC SELECT”
(“S-DVC SEL”)
“DEVICE DELETE” Cancel registration of the Bluetooth device. Refer
(“DVC DELETE”) to <Deleting a Registered Bluetooth Device>
(page 21).
“PIN CODE EDIT” Specify the PIN code required when registering
(“PIN EDIT”)
this unit using the Bluetooth device. Refer to
<Registering PIN Code> (page 22).
|
20 KDC-BT40U/KDC-BT30
Registering Bluetooth Device (Pairing)
2 Enter Special device registration mode
Press the [VOL] knob.
A list is displayed.
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
3 Select a device name
Turn the [VOL] knob and press it when the
desired device name is displayed.
If “COMPLETE” is displayed, registration is
completed.
Registering from this unit
1 Select Bluetooth device registration mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” (“DETAIL
SET”) > “DEVICE REGIST” (“DVC REGIST).
4 Go through the procedure step 3 of
<Registering from this unit> and complete the
registration (pairing).
2 Enter Bluetooth device registration mode
Press the [VOL] knob.
Search for the Bluetooth device.
Cancelling Special device registration mode
Press the [
] button for at least 1 second.
⁄
When search is completed, “FINISHED” is displayed.
•
If the device name is not in the list, select “OTHER
3 Select the Bluetooth device
PHONE”.
Turn the [VOL] knob and press it when the
desired Bluetooth device name is displayed.
Deleting a Registered Bluetooth Device
4 Input the PIN code
You can delete a registered Bluetooth device.
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
1 Select Bluetooth device deletion mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20)
Press the [¢
4
] button.
] button.
Press the [
Select “SETTINGS” > “DETAILED SET” (“DETAIL
SET”) > “DEVICE DELETE” (“DVC DELETE”).
5 Transmit the PIN code
Press the [VOL] knob.
If “PAIRING OK” is displayed, registration is
completed. If the error message appears even
though the PIN code is correct, try Registering
Special Bluetooth device.
2 Enter Bluetooth device deletion mode
Press the [VOL] knob.
“(name)” is displayed.
3 Select the Bluetooth device
6 Return to the device list
Turn the [VOL] knob.
Press the [VOL] knob.
4 Delete the selected Bluetooth device
Press the [VOL] knob.
“DELETE” is displayed.
7 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
5 Exit Function Setting mode
•
This unit allows up to 8 digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be
input from the Bluetooth device.
If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
Press the [
] button for at least 1 second.
⁄
•
When a registered cell-phone is deleted, its Phone Book,
•
log, SMS, and voice tag are also deleted.
Registering Special Bluetooth device
Allow registration of a special device that cannot
be registered normally (pairing).
1 Select Special device registration mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” (“DETAIL
SET”) > “S-DVC SELECT” (“S-DVC SEL”).
English
|
21
Bluetooth Setup
Registering PIN Code
Downloading the Phone Book
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
1 Select PIN code edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
Select “SETTINGS” > “DETAILED SET” (“DETAIL
SET”) > “PIN CODE EDIT” (“PIN EDIT”).
2 Enter PIN code edit mode
Press the [VOL] knob.
The current setting of PIN code is displayed.
⁄
•
•
Setting on the cell-phone may be required.
If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
3 Input the PIN code
Operation type
Operation
Select the numbers.
Turn the [VOL] knob.
Move to the next digit. Press the [
Delete the last digit. Press the [
¢
4
] button.
] button.
To download from the cell-phone manually
1 By operating the cell-phone, end the hands-free
connection.
4 Register a PIN code
Press the [VOL] knob.
2 By operating the cell-phone, send the phone
book data to this unit
By operating the cell-phone, download the phone
If “COMPLETE” is displayed, registration is
completed.
book data to this unit.
• During downloading:
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
“DOWNLOADING” is displayed.
• After completion of downloading:
“COMPLETE” is displayed.
⁄
•
By default, “0000” is specified.
A PIN code can be specified with up to 8 digits.
•
3 By operating the cell-phone, start the hands-
free connection.
⁄
Displaying the Firmware Version
•
Up to 1000 person phone numbers can be registered for
each registered cell-phone.
Display the version of the firmware of this unit.
•
Up to 25 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type
of characters.)
1 Enter Bluetooth Firmware update mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” (“DETAIL
SET”) > “BT F/W UPDATE” (“BT UPDATE”).
•
To cancel downloading of the phone book data, operate
the cell-phone.
2 Enter Bluetooth Firmware update mode
Press the [VOL] knob.
The firmware version appears.
3 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
For how to update the firmware, access our web site.
|
22 KDC-BT40U/KDC-BT30
Selecting the Bluetooth Device You
Wish to Connect
Downloading the SMS
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
When 2 or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
1 Select SMS download mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “SMS DOWNLOAD” (“SMS
DL”).
1 Select Bluetooth device selection mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “PHONE SELECT” (“PHONE
SEL”).
2 Enter SMS download mode
Press the [VOL] knob.
“DOWNLOADING” is displayed.
When the downloading finishes, “COMPLETE” is
displayed.
2 Enter Bluetooth device selection mode
Press the [VOL] knob.
“(name)” is displayed.
3 Exit Function Setting mode
3 Select the Bluetooth device
Press the [
] button for at least 1 second.
Turn the [VOL] knob.
4 Set up the Bluetooth device
⁄
•
The cell-phone must be able to transmit the SMS using
Press the [VOL] knob.
Bluetooth. Setting on the cell-phone may be required.
If the cell-phone does not support SMS function, the
SMS download item in Function Control mode is not
displayed.
When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
‘✱(name)’ or ‘-(name)’ is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
•
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
If a cell-phone is already selected, deselect it, and then
select a different one.
English
|
23
Bluetooth Setup
SMS (Short Message Service)
Adding a Voice Dialing Command
The SMS arrived at the cell-phone is displayed on
the receiver.
Add a voice tag to the phone book for voice dialing.
You can register up to 35 voice tags.
A newly arrived message is displayed.
1 Select Phone book name edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
¤
•
To prevent car accidents, the driver should not read the
SMS while driving.
Select “SETTINGS” > “VOICE TAG”.
2 Enter Voice Tag edit mode
When a new message arrives
“SMS RECEIVED” (“NEW SMS”) is displayed.
The display disappears with any operations.
Press the [VOL] knob.
3 Enter Phone book name edit mode
Turn the [VOL] knob to select “PB NAME EDIT”
(“PB NAME EDT”), and then press the [VOL]
knob.
Displaying the SMS
1 Select SMS Inbox mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20)
4 Search for the name to register
Select the name to register with reference to 3 in
<Calling a Number in the Phone Book> (page 12).
If a voice tag has already been registered for a
name, “*” is displayed before the name.
Select > “SETTINGS” > “SMS INBOX”.
2 Enter SMS Inbox mode
Press the [VOL] knob.
A message list appears.
5 Select a mode
3 Select a message
Turn the [VOL] knob.
Turn the [VOL] knob.
Display
Operation
Each pushing of the [ ] button switches
between telephone number or name and message
reception date.
“PB NAME REG”
“PB NAME CHK”*
“PB NAME DEL”*
“RETURN”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 3.
4 Display the text
Press the [VOL] knob.
* Displayed only when a name for which a voice tag has
been registered is selected.
Turning the [VOL] knob scrolls the message.
Pressing the [VOL] knob again returns to the
message list screen.
Select “PB NAME REG” (Register)
6 Register a voice tag (first)
Press the [VOL] knob.
“ENTER1” is displayed.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
When a beep is heard, say a voice tag within 2
seconds.
•
The unopened message is displayed at the beginning
of the list. Other messages are displayed in the order of
reception.
The SMS that has arrived when the cell-phone is not
linked with Bluetooth cannot be displayed. Download
the SMS.
The short message cannot be displayed during
downloading the SMS.
7 Confirm the voice tag (second)
Press the [VOL] knob.
“ENTER 2” is displayed.
When a beep is heard, say the same voice tag as
that you said in step 5 within 2 seconds.
“COMPLETE” is displayed.
•
•
•
Unread messages are prefixed with an asterisk (*).
8 End registration
Press the [VOL] knob.
Return to step 3. You can register another voice tag
continuously.
|
24 KDC-BT40U/KDC-BT30
⁄
⁄
•
If your voice cannot be recognized, a message is
•
Set the voice tag for all the 5 categories. If the voice tag
displayed. Pressing the [VOL] knob allows you to retry
voice input. (page 37)
is not registered for all the categories, the Phone book
may not be recalled by voice command.
Select “PB NAME CHK” (Play)
6 Press the [VOL] knob.
Play the registered voice and return to step 3.
Select “PB NAME DEL” (Delete)
6 Delete a voice tag
Press the [VOL] knob.
Exit Phone book name edit mode
Press the [
] button for at least 1 second.
⁄
•
Audio sound is not output during voice tag registration.
Setting a Voice Command for
Category
Add a voice tag to the phone number category
(type) for voice calling.
1 Select Phone Number type edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “VOICE TAG”.
2 Enter Voice Tag edit mode
Press the [VOL] knob.
3 Enter Phone Number type edit mode
Turn the [VOL] knob to select “PN TYPE EDIT”
(“PN TYPE EDT”), and then press the [VOL]
knob.
4 Select the category (type) you wish to set
Turn the [VOL] knob and press it when the
desired category name is displayed.
“GENERAL”/ “HOME”/ “OFFICE”/ “MOBILE”/ “OTHER”
5 Select a mode
Turn the [VOL] knob.
Display
Operation
“PN TYPE REG”
“RETURN”
Register a voice tag.
Return to step 3.
6 Register the category (type) by performing
steps 6 to 8 of select “PB NAME REG” (Register)
in <Adding aVoice Dialing Command> (page 24).
7 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
25
Optional Accessory (KCA-RC405)
Basic Operations of Remote Control
In iPod/CD/Audio file Source
Music select [4]/[¢] button
Folder/Disc select [FM+]/[AM–] button
Pause/Play [38] button
Enter Music search mode [5]/[∞] button
Movement between folders/files in Music search
VOL
SRC
ATT
ENT
ꢂ/P
mode [5]/[∞] button
Return to previous folder [ ] button
AUD
FM
EXIT
AM
Hands-Free Phone Control
0 — 9
Making a call
Enter Bluetooth mode
[
] button
Enter the dialing method selection mode
[5]/[∞] button
DIRECT/OK
(page 9, 13)
Select a dialing method [ENT] button
Number dial input
Operation type
Input a digit.
Input“+”.
Input“#”.
Input“*”.
Operation
Volume control [VOL] button
Source select [SRC] button
Volume reduce [ATT] button
“ATT“ indicator is blinks when the attenuator function
is on. (KDC-BT40U only). When the button is pressed
again, the volume returns to the previous level.
[0] – [9] buttons
[¢] button
[FM+] button
[AM–] button
[4] button
Clear the entered phone number.
Make a call [OK] button
Enter Audio Control mode [AUD] button
⁄
Receiving a call
•
Refer to <Audio Control> (page 15) for the operation
method, such as the procedures for Audio control and
others operations.
Answer the call
[
] button
Switch between the private talk mode and the
hands-free talk mode [38] button
Return to previous item
[
] button
Exit from mode [EXIT] button
Selection of item [5]/[∞] button
Determination [ENT] button
Call waiting
Answer Another Incoming Call with the Current
Call Suspended
[
] button
Answer another Incoming Call after Terminating
the Current Call [SRC] button
In Tuner Source
Continue the Current Call [1] button
Band select [FM+]/[AM–] button
Station select [4]/[¢] button
Recall preset stations [1] — [6] button
During a call
End the call [SRC] button
Adjust the voice volume [VOL] button
|
26 KDC-BT40U/KDC-BT30
Preparing the remote control unit
Pull the battery sheet out from the remote control
unit to the direction of the arrow.
Changing the battery of the remote control
unit
Use a commercially available button battery (CR2025).
1 Insert something narrow like a paperclip into the
hole and pull out the battery tray.
Press
Pull out
2 Insert the battery with the + and – poles aligned
properly, following the illustration inside the case.
CR2025(+side)
¤ CAUTION
• Do not set the remote control in hot places such
as on the dashboard.
• Lithium battery.
Danger of explosion if the battery is incorrectly
replaced.
Replace only with the same or equivalent type.
• The battery pack or batteries shall not be exposed
to excessive heat such sunshine, fire or the like.
• Keep battery out of reach of children and in
original package until ready to use. Dispose of
used batteries promptly. If swallowed contact
physician immediately.
English
|
27
Appendix
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
About Audio file
•
•
•
•
Playable Audio file
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device (KDC-BT40U only)
USB mass storage class
iPod/iPhone that can be connected to this
unit (KDC-BT40U only)
Made for
• iPod nano (1st generation) • iPod nano (2nd generation)
• iPod nano (3rd generation) • iPod nano (4th generation)
• iPod nano (5th generation)
•
Playable USB device file system
FAT16, FAT32
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• iPod with video
• iPod classic
• iPod touch (1st generation) • iPod touch (2nd generation)
Works with
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
• iPhone
• iPhone 3G
• iPhone 3GS
<
v
: Folder
Folder
:
A
CD
(ꢂ)
udiofile
vꢀ
ꢁ
ꢃ
vꢆ
vꢇ
• Update iPod/iPhone software to the latest version.
• Type of control available varies depending on the
type of connected iPod. See www.kenwood.com/
cs/ce/ipod for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable*. A KCA-iP101 is required (optional
accessory).
* Not supported model KCA-iP500.
Refer to the web site for connectable iPod and iPod
connection cable.
ꢅ
vꢄ
ꢈ
vꢉ
v.
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
About USB device
• In this manual, the word “USB device” is used for
flash memories and digital audio players which have
USB terminals.
•
If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
•
You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
|
28 KDC-BT40U/KDC-BT30
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
Version
Profile
Bluetooth Standard Ver. 2.0
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phone book Access Profile)
SYNC (Synchronization Profile)
Information on Disposal of Old Electrical
and Electronic Equipment and Batteries
(applicable for EU countries that have
adopted separate waste collection systems)
Products and batteries with the symbol
(crossed-out wheeled bin) cannot be
disposed as household waste.
For the cell-phones verified for compatibility, access
the following URL:
Old electrical and electronic equipment
and batteries should be recycled at a facility
capable of handling these items and their
waste byproducts.
Contact your local authority for details in
locating a recycle facility nearest to you.
Proper recycling and waste disposal will
help conserve resources whilst preventing
detrimental effects on our health and the
environment.
⁄
•
The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
HFP is a profile used to make a hands-free call.
OPP is a profile used to transfer data such as a phone book
between units.
•
•
Notice: The sign “Pb” below the symbol for
batteries indicates that this battery
contains lead.
About “KENWOOD Music Editor”
(KDC-BT40U only)
• This unit supports the PC application “KENWOOD
Music Editor Lite ver1.0” or later.
The marking of products using lasers
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Lite ver1.0”, you can search a file by title, album or
artist name using the <Music Search> (page 7).
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
• “KENWOOD Music Editor Lite ver1.0” is available from
the following web site:
• For further information on “KENWOOD Music Editor
Lite ver1.0”, refer to the site above or the application
help.
English
|
29
Appendix
Function Item List
In Standby
In USB/ iPod source*
1st hierarchy
2nd hierarchy
3rd hierarchy
Page
15
“AUDIO CONTROL”(See in CD/ Audio file source)
(“AUDIO CTRL”)
“DISP SELECT”
1st hierarchy
“DISP SELECT”
“SETTINGS”
2nd hierarchy
3rd hierarchy
Page
16
16
“CLOCK”
“CLOCK ADJUST”
(“CLOCK ADJ”)
“TIME SYNC”
“DIMMER SET”
“TEXT SCROLL”
“SETTINGS”
“SKIP SEARCH”
18
17
9
“MPLIST DELETE”
“CLOCK”(See in standby)
“DISPLAY”(See in standby)
“RDS SET”(See in TUNER source)
18
17
10
18
“DISPLAY”
“BT DVC STATUS”
(“DVC STATUS”)
“DEMO MODE”
“INITIAL SET”
“PRESET TYPE”
“KEY BEEP”
“RUSSIAN SET”
“P-OFF WAIT”
“BUILT-IN AUX”
(“BUILTIN AUX”)
“CD READ”
“SWITCH PREOUT”
(“SWITCH PRE”)
In Tuner source
1st hierarchy
2nd hierarchy
3rd hierarchy
Page
15
“AUDIO CONTROL”(See in CD/ Audio file source)
(“AUDIO CTRL”)
“DISP SELECT”
16
18
“SETTINGS”
“LOCAL SEEK”
“SEEK MODE”
“AUTO MEMORY”
“MONO SET”
“NEWS SET”
“AF SET”
“SP SELECT”
“F/W UP”
10
“DEMO MODE”
18
“RDS REGIONAL”
(“RDS REG”)
In CD/ Audio file source
“AUTO TP SEEK”
(“ATP SEEK”)
“CLOCK”(See in standby)
1st hierarchy
“AUDIO CONTROL” “SUBWOOFER SET”
(“AUDIO CTRL”)
2nd hierarchy
3rd hierarchy
Page
18
17
18
(“SUB-W SET”)
“BASS BOOST”
“SYSTEM Q”
“BASS LEVEL”
“MID LEVEL”
“TRE LEVEL”
“BALANCE”
“FADER”
“SUB-W LEVEL”
“DETAILED SET”
(“DETAIL SET”)
“DISPLAY”(See in standby)
“DEMO MODE”
In AUX source
1st hierarchy
2nd hierarchy
“AUDIO CONTROL”(See in CD/ Audio file source)
(“AUDIO CTRL”)
3rd hierarchy
Page
15
15
“DISP SELECT”
“SETTINGS”
16
“AUX NAME SET”
(“AUX NAME”)
“CLOCK”(See in standby)
“DISPLAY”(See in standby)
17
“LPF SUBWOOFER”
(“LPF SUB-W”)
“SUB-W PHASE”
“SUPREME SET”
“VOLUME OFFSET”
(“VOL OFFSET”)
18
17
10
18
“RDS SET”(See in TUNER source)
“DEMO MODE”
“DISP SELECT”
“SETTINGS”
16
18
17
10
18
“CLOCK”(See in standby)
“DISPLAY”(See in standby)
“RDS SET”(See in TUNER source)
“DEMO MODE”
|
30 KDC-BT40U/KDC-BT30
In Hands-Free BT mode
1st hierarchy
“DISP SELECT”
“SETTINGS”
2nd hierarchy
3rd hierarchy
Page
16
“PHONE SELECT”
(“PHONE SEL”)
“SMS DOWNLOAD”
(“SMS DL”)
“SMS INBOX”
“VOICE TAG”
“DETAILED SET”
(“DETAIL SET”)
“DEVICE REGIST”
(“DVC REGIST”)
“S-DVC SELECT”
(“S-DVC SEL”)
“DEVICE DELETE”
(“DVC DELETE”)
“PIN CODE EDIT”
(“PIN EDIT”)
20
“AUTO ANSWER”
“BT SP SELECT”
(“BT SP SEL”)
“CALL BEEP”
“BT F/W UPDATE”
(“BT UPDATE”)
“MIC GAIN”
“NR LEVEL”
“EC LEVEL”
“CLOCK”(See in standby)
“DISPLAY”(See in standby)
18
17
18
“DEMO MODE”
*KDC-BT40U only
(“ ”) encloses a display appearing on the KDC-BT30. It is
shown only if it differs from the one appearing on the
KDC-BT40U.
English
|
31
Accessories/ Installation Procedure
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Accessories
1
•
..........1
•
•
•
2
..........2
•
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
Installation Procedure
•
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Reception may drop if there are metal objects near the
Bluetooth antenna.
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
•
•
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
Bluetooth antenna unit
For Good Reception
To assure good reception, note the following:
• Communicate with the cell-phone within the line-
of-sight distance of 10 m (30 ft). The communication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
above maximum communication range (10 m) is
not always assured.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
• A broadcast station or walkie-talkie located nearby
can interfere with communication due to too strong
signal.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
•
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
|
32 KDC-BT40U/KDC-BT30
Connecting Wires to Terminals
KDC-BT30
KDC-BT40U
AUX input (Stereo)
Use the mini-plug cable which is
stereo type and does not have any
resistance.
USB connector
Antenna Cord
FM/AM antenna input (JASO)
Rear output/Sub Woofer output
R
L
Switches the preout between rear output (“REAR”) and subwoofer
output (“SUB-W”). Refer to “SWITCH PREOUT”/(“SWITCH PRE” ) of
<Initial Setting> (page 18).
Fuse (10A)
Wiring harness (Accessory1)
If no connections are made, do not let the wire come out from the tab.
Mute control wire (Brown)
To connect the Kenwood navigation system, consult your
navigation manual.
MUTE
Steering remote control (Light Blue/Yellow)
To use the steering wheel remote control feature, you
need to an exclusive remote adapter (not supplied)
matches your car is required.
REMOTE CONT
STEERINGWHEEL
REMOTE INPUT
Power control/Motor antenna
control wire (Blue/White)
Connect either to the power control terminal when using
the optional power amplifier, or to the antenna control
terminal in the vehicle.
P.CONT
ANT. CONT
Battery wire (Yellow)
Ignition wire (Red)
See next page
A–7 Pin (Red)
A–4 Pin (Yellow)
Connector A
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Connector B
English
|
33
Connecting Wires to Terminals
Connector Function Guide
2WARNING
Pin Numbers for
ISO Connectors
External Power
Connector
Cable Colour
Functions
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
Yellow
Blue/White
Red
Battery
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2,
make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
A-5
A-7
A-8
Power Control
Ignition (ACC)
Black
Earth (Ground)
Connection
Speaker Connector
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and
the A-4 pin (yellow) is connected to the constant
power supply.
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Purple
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Purple/Black
Gray
Gray/Black
White
Ignition cable (Red)
A-7 Pin (Red)
White/Black
Green
Unit
Vehicle
Battery cable (Yellow)
A-4 Pin (Yellow)
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
Ignition cable (Red)
A-7 Pin (Red)
Unit
Vehicle
Battery cable (Yellow)
A-4 Pin (Yellow)
|
34 KDC-BT40U/KDC-BT30
Installation/Removing the Unit
Installation
Removing the Hard Rubber Frame
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Accessory2
⁄
Removal tool
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2 When the upper level is removed, remove the
lower two locations.
⁄
•
The frame can be removed from the bottom side in the
same manner.
Removing the Unit
1 Refer to the section <Removing the Hard Rubber
Frame> and then remove the hard rubber frame.
2 Detach the faceplate.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Accessory2
¤
•
¤ CAUTION
Be careful to avoid injury from the catch pins on the
removal tool.
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
5 Pull the unit all the way out with your hands, being
careful not to drop it.
English
|
35
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
Audio file source
? The sound skips when an Audio file is being
played.
!
• Cannot set up the subwoofer.
✔
✔
The media is scratched or dirty.
• Cannot set up the low pass filter.
• No output from the subwoofer.
• “SUBWOOFER SET”/(“SUB-W SET”) of <Audio
Control> (page 15) is not set to ON.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
The recording condition is bad.
Record the media again or use another media.
☞
• Preout is not set to subwoofer.
☞ “SWITCH PREOUT” /(“SWITCH PRE”) of <Initial
Setting> (page 18).
Hands-free phoning
? The hands-free talk volume is low.
✔
The hands-free talk volume is set at a low level.
!
Cannot set up the subwoofer phase.
The Low Pass Filter is set to “THROUGH”.
☞ “LPF SUBWOOFER”/ (“LPF SUB-W”) of <Audio
Control> (page 15).
☞
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free
talk. “MIC GAIN”, “NR LEVEL” and “EC LEVEL” of
<Bluetooth Setup> (page 20).
!
!
Power OFF Timer does not function.
<Exit of the Demonstration Mode> (page 5) is not
turned off.
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
✔
☞
No sound is heard from the rear speakers in the
hands-free talk mode.
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
? No beep is heard at reception of an incoming call.
✔
No beep is heard depending on the type of your
cell-phone.
☞
“CALL BEEP” of <Bluetooth Setup> (page 20) is set
to ON.
? Voice is not recognized.
✔
✔
✔
The vehicle window is open.
What might seem to be a malfunction in your unit
may just be the result of slight miss operation or
miss wiring. Before calling service, first check the
following table for possible problems.
☞
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
Small voice.
If voice is too small, it cannot be recognized
☞
properly. Speak into the microphone a little more
loudly and naturally.
The person saying the voice tag is not the one who
registered the it.
General
? The operation check sound (beep sound) does not
sound.
☞
Only the voice of the person who registered the
voice tag can be recognized.
✔
The preout jack is being used.
☞
The operation check sound (beep sound) cannot
be output for the preout jack.
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
☞
Clean the CD, referring to the CD cleaning of the
section on <Handling CDs> (page 3).
The disc is severely scratched.
Try another disc instead.
☞
|
36 KDC-BT40U/KDC-BT30
NO MUSIC DATA/ERROR 15:
• The connected USB device contains no
The messages shown below display your
systems condition.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
TOC ERROR:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
USB ERROR:
iPod ERROR:
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
ERROR 05:
ERROR 77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
“ERROR 77” code does not disappear,
consult your nearest service center.
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
IN (Blink):
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
USB REMOVE (Blink):
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
NO NUMBER: • The calling party does not notify a caller ID.
• There is no phone number data.
PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the “PROTECT” code does not disappear,
consult your nearest service center.
NO DATA:
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
NO ENTRY:
The cell-phone has not been registered
(pairing).
NA FILE:
An Audio file is played with a format that this
unit can’t support.
HF DISCONCT: The unit cannot communicate with the cell-
phone.
COPY PRO:
A copy-protected file is played.
HF ERROR 07: The memory cannot be accessed.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
READ ERROR: The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
HF ERROR 68: The unit cannot communicate with the cell-
phone.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
NO DEVICE:
N/A DEVICE:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
UNKNOWN:
The Bluetooth device cannot be detected.
DEVICE FULL: 5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
• An unsupported USB device is connected.
• Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 28) for information on supported
iPods.
PIN CODE NG: The PIN code is wrong.
CONNECT NG: The unit cannot be connected to the device.
PAIRING NG:
Pairing error.
English
|
37
Troubleshooting Guide
Specifications
NO MATCHING: The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
FM Tuner Section
Frequency Range (50 kHz Space)
: 87.5 MHz – 108.0 MHz
Usable Sensitivity (S/N = 26dB)
: 1.0 μV/75 Ω
Quieting Sensitivity (DIN S/N = 46dB)
: 2.5 μV/75 Ω
Frequency Response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise Ratio (MONO)
: 63 dB
TOO SOFT:
TOO LOUD:
TOO LONG:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be
recognized.
NO PHONEBOOK (NO PB):
Data is not contained in the phone book.
NO MESSAGE: No short message in In Box.
Stereo Separation (1 kHz)
: 40 dB
NO RECORD: The voice tag is not registered in the phone
book.
MW Tuner Section
Frequency Range (9 kHz space)
: 531 kHz – 1611 kHz
Usable Sensitivity (S/N = 20dB)
: 36 μV
MEMORY FULL: The number of voice tags reaches the
maximum number to be registered in the
phone book.
NO ACCESS:
The procedure preset with mixed preset
memory function cannot be available.
The preset content may not be recalled
depending on the selected band.
LW Tuner Section
Frequency Range
: 153 kHz – 279 kHz
NO VOICE:
No call.
Usable Sensitivity (S/N = 20dB)
: 57 μV
CD Player Section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle Speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency Response ( 1 dB)
: 20 Hz – 20 kHz
Total Harmonic Distortion (1 kHz)
: 0.01 %
Signal to Noise Ratio (1 kHz)
: 105 dB
Dynamic Range
: 93 dB
MP3 Decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA Decode
: Compliant with Windows Media Audio
AAC Decode
: AAC-LC “.m4a” files
|
38 KDC-BT40U/KDC-BT30
USB Interface (KDC-BT40U)
General
USB Standard
: USB1.1/ 2.0 (Full Speed)
Operating Voltage
: 14.4 V (10.5 – 16V allowable)
File System
: FAT16/ 32
Maximum Current Consumption
: 10 A
MP3 Decode
: Compliant with MPEG-1/2 Audio Layer-3
Installation Size (W x H x D)
: 182 x 53 x 155 mm
WMA Decode
: Compliant with Windows Media Audio
Weight
: 1.3 kg
AAC Decode
: AAC-LC “.m4a” files
Maximum Supply Current
: 500 mA
Specifications subject to change without notice.
Bluetooth Section
Version
: Bluetooth Ver. 2.0 Certified
Frequency Range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication Range
: Line of sight approx.10m (32.8 ft)
Profile
: HFP (Hands Free Profile)
: HSP (Headset Profile)
: SPP (Serial Port Profile)
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
Audio Section
Maximum Output Power
•
•
The “AAC” logo is a trademark of Dolby Laboratories.
: 50 W x 4
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
Output Power (DIN 45324, +B=14.4V)
: 30 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone Action
Bass : 100 Hz 8 dB
•
•
iTunes is a trademark of Apple Inc.
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout Level / Load (CD)
: 2000 mV/10 kΩ
Preout Impedance
: ≤ 600 Ω
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
•
•
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
Auxiliary Input
Frequency Response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
•
•
“Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
English
|
39
Magyar
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Alulírott, Kenwood, kijelenti, hogy a jelen KDC-BT40U/KDC-BT30 megfelel az
1999/5/EC irányelvben meghatározott alapvető követelményeknek és egyéb
vonatkozó előírásoknak.
Svenska
Declaration of Conformity with regard to
the R&TTE Directive 1999/5/EC
Härmed intygar Kenwood att denna KDC-BT40U/KDC-BT30 stär l
överensstämelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.
Suomi
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
Kenwood vakuuttaa täten että KDC-BT40U/KDC-BT30 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
EU Representative’s:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
Slovensko
S tem Kenwood izjavlja, da je ta KDC-BT40U/KDC-BT30 v skladu z osnovnimi
zahtevami in ostalimi ustreznimi predpisi Direktive 1999/5/EC.
Slovensky
Spoločnosť Kenwood týmto vyhlasuje, že KDC-BT40U/KDC-BT30 spĺňa zákldné
požiadavky a ďalšie prislušné ustanovenia Direktĺvy 1999/5/EC.
Dansk
English
Hereby, Kenwood declares that this unit KDC-BT40U/KDC-BT30 is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
Undertegnede Kenwood erklærer harved, at følgende udstyr
KDC-BT40U/KDC-BT30 overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Français
Par la présente Kenwood déclare que l’appareil KDC-BT40U/KDC-BT30 est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Kenwood ΔΗΛΩΝΕΙ ΟΤΙ KDC-BT40U/KDC-BT30
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/EK.
Par la présente, Kenwood déclare que ce KDC-BT40U/KDC-BT30 est conforme
aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE
qui lui sont applicables.
Deutsch
Eesti
Sellega kinnitab Kenwood, et see KDC-BT40U/KDC-BT30 vastab direktiivi
1999/5/EC põhilistele nõudmistele ja muudele asjakohastele määrustele.
Latviešu
Hiermit erklärt Kenwood, dass sich dieser KDC-BT40U/KDC-BT30 in
Übereinstimmung mit den grundlegenden Anforderungen und den anderen
relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi)
Hiermit erklärt Kenwood die Übereinstimmung des Gerätes
KDC-BT40U/KDC-BT30 mit den grundlegenden Anforderungen und den
anderen relevanten Festlegungen der Richitlinie 1999/5/EG. (Wien)
Nederlands
Ar šo, Kenwood, apstiprina, ka KDC-BT40U/KDC-BT30 atbilst Direktīvas 1999/5/
EK galvenajām prasībām un citiem tās nosacījumiem.
Lietuviškai
Šiuo, Kenwood, pareiškia, kad šis KDC-BT40U/KDC-BT30 atitinka pagrindinius
Direktyvos 1999/5/EB reikalavimus ir kitas svarbias nuostatas.
Malti
Hierbij verklaart Kenwood dat het toestel KDC-BT40U/KDC-BT30 in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG.
Bij deze verklaat Kenwood dat deze KDC-BT40U/KDC-BT30 voldoet aan de
essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/
EC.
Hawnhekk, Kenwood, jiddikjara li dan KDC-BT40U/KDC-BT30 jikkonforma mal-
ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Українська
Компанія Kenwood заявляє, що цей виріб KDC-BT40U/KDC-BT30 відповідає
ключовим вимогам та іншим пов’язаним положенням Директиви
1999/5/EC.
Italiano
Con la presente Kenwood dichiara che questo KDC-BT40U/KDC-BT30 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Español
Por medio de la presente Kenwood declara que el KDC-BT40U/KDC-BT30
cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.
Português
For Turkey
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan
Elektrikli ve Elektronik Eşyalarda Bazı Zararlı Maddelerin
Kullanımının Sınırlandırılmasına Dair Yönetmeliğe uygun
olarak üretilmiştir.
Kenwood declara que este KDC-BT40U/KDC-BT30 está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Polska
This product complies with Directive, Number 26891
regarding “REGULATION ON THE RESTRICTION OF
THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN
LECTRICAL AND ELECTRONIC EQUIPMENT”.
Kenwood niniejszym oświadcza, że KDC-BT40U/KDC-BT30 spełnia zasadnicze
wymogi oraz inne istotne postanowienia dyrektywy 1999/5/EC.
Český
Kenwood timto prohlasuje, ze KDC-BT40U/KDC-BT30 je ve shode se zakladnimi
pozadavky a s dalsimi prislusnymi ustanoveni Narizeni vlady c. 426/2000 Sb.
This symbol mark indicates that
Kenwood manufactured this product
so as to decrease harmful influence on
the environment.
|