This product is eligible for the AVCCAM
3 Year Warranty Repair Program. For
details, see page 9.
Operating Instructions
Memory Card Camera-Recorder
Model No.
Model No.
AG-3DA1P
AG-3DA1E
Before operating this product, please read the instructions carefully and save
this manual for future use.
ENGLISH
SS0710AS1080 -PS D
Printed in Japan
VQT2Z46-1
Read this first! (For AG-3DA1P) (continued)
indicates safety information.
CAUTION:
CAUTION:
Do not leave the unit in direct contact with the
skin for long periods of time when in use.
Low temperature burn injuries may be suffered
if the high temperature parts of this unit are
in direct contact with the skin for long periods
of time. When using the equipment for long
periods of time, make use of the tripod.
This apparatus can be operated at a voltage in
the range of 110 – ꢀ40 V AC.
Voltages other than 1ꢀ0 V are not intended for
U.S.A. and Canada.
Operation at a voltage other than 1ꢀ0 V AC
may require the use of a different AC plug.
Please contact either a local or foreign
Panasonic authorized service center for
assistance in selecting an alternate AC plug.
FCC NOTICE (USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (ꢀ) this device must accept any
interference received, including interference that may cause undesired operation
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions
and the user must use only shielded interface cables when connecting to host computer or
peripheral devices. Also any unauthorized changes or modifications to this equipment could void
the user's authority to operate this device.
NOTIFICATION (Canada)
This class B digital apparatus complies with Canadian ICES-003.
A lithium ion/polymer battery that is recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special
handling may apply.
3
Read this first! (For AG-3DA1P) (continued)
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
ꢀ) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
1ꢀ) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
Note:
Camera-Recorder
The rating plate is on the underside of the viewfinder.
Battery Charger / AC Adaptor
The rating plate is on the underside of the Battery Charger and AC Adaptor. Disconnect the AC mains
plug from the AC mains socket when not in use.
Conforms to ANSI/UL Std. 60065
4
Read this first! (For AG-3DA1E)
indicates safety information.
WARNING:
CAUTION:
This equipment must be earthed.
The mains plug of the power supply cord shall
remain readily operable.
To ensure safe operation, the three-pin plug
must be inserted only into a standard three-
pin power point which is effectively earthed
through normal household wiring.
The AC receptacle (mains socket outlet) shall
be installed near the equipment and shall be
easily accessible.
Extension cords used with the equipment must
have three cores and be correctly wired to
provide connection to the earth. Wrongly wired
extension cords are a major cause of fatalities.
The fact that the equipment operates
satisfactorily does not imply that the power
point is earthed or that the installation is
completely safe. For your safety, if you are
in any doubt about the effective earthing of
the power point, please consult a qualified
electrician.
To completely disconnect this equipment from
the AC mains, disconnect the power cord plug
from the AC receptacle.
CAUTION:
Danger of explosion or fire if battery is
mistreated.
• Do not leave the battery in an automobile
exposed to direct sunlight for a long period
of time with doors and windows closed.
• Do not disassemble the battery or dispose
of it in fire.
WARNING:
• Do not store in temperatures over 60 °C
(140 °F).
• Use specified battery charger.
• Replace only with same or specified type.
• To reduce the risk of fire or electric shock,
do not expose this equipment to rain or
moisture.
• To reduce the risk of fire or electric shock
hazard, keep this equipment away from all
liquids. Use and store only in locations which
are not exposed to the risk of dripping or
splashing liquids, and do not place any liquid
containers on top of the equipment.
CAUTION:
In order to maintain adequate ventilation, do
not install or place this unit in a bookcase,
built-in cabinet or any other confined space.
To prevent risk of electric shock or fire hazard
due to overheating, ensure that curtains
and any other materials do not obstruct the
ventilation.
WARNING:
Always keep memory cards (optional
accessory) or accessories (screw spacer,
microphone holder screws, microphone holder
adapter, INPUT terminal covers) out of the
reach of babies and small children.
CAUTION:
Do not lift the unit by its handle while the
tripod is attached. When the tripod is attached,
its weight will also affect the unit’s handle,
possibly causing the handle to break and
hurting the user. To carry the unit while the
tripod is attached, take hold of the tripod.
CAUTION:
Do not remove panel covers by unscrewing
them.
To reduce the risk of electric shock, do not
remove the covers. No user serviceable parts
inside.Refer servicing to qualified service
personnel.
CAUTION:
Excessive sound pressure from earphones
and headphones can cause hearing loss.
CAUTION:
CAUTION:
To reduce the risk of fire or electric shock and
annoying interference, use the recommended
accessories only.
Do not leave the unit in direct contact with the
skin for long periods of time when in use.
Low temperature burn injuries may be suffered
if the high temperature parts of this unit are
in direct contact with the skin for long periods
of time. When using the equipment for long
periods of time, make use of the tripod.
CAUTION:
Do not jar, swing, or shake the unit by its
handle.
Any strong jolt to the handle may damage the
unit or result in personal injury.
Note:
Camera-Recorder
The rating plate is on the underside of the viewfinder.
Battery Charger / AC Adaptor
The rating plate is on the underside of the Battery Charger and AC Adaptor. Disconnect the AC mains
plug from the AC mains socket when not in use.
5
Read this first! (For AG-3DA1E) (continued)
indicates safety information.
Caution for AC Mains Lead
For battery charger
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe,
etc. and the other one is only for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is
not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
FOR U.K. ONLY
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
How to replace the fuse
1. Open the fuse compartment with a
screwdriver.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a
rating of 5 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI
mark on the body of the fuse.
If the plug contains a removable fuse cover
you must ensure that it is refitted when the
fuse is replaced.
2. Replace the fuse
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
Fuse
A replacement fuse cover can be
purchased from your local Panasonic
Dealer.
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
6
Read this first! (For AG-3DA1E) (continued)
indicates safety information.
Caution for AC Mains Lead
For AC adaptor
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe,
etc. and the other one is only for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is
not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
FOR U.K. ONLY
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
How to replace the fuse
1. Open the fuse compartment with a
screwdriver.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a
rating of 5 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI
mark on the body of the fuse.
If the plug contains a removable fuse cover
you must ensure that it is refitted when the
fuse is replaced.
2. Replace the fuse
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
Fuse
A replacement fuse cover can be
purchased from your local Panasonic
Dealer.
7
Read this first! (For AG-3DA1E) (continued)
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Applicable standards and operating environment
The apparatus is compliant with:
• standards EN55103-1 and EN55103-ꢀ ꢀ009, and
• electromagnetic environments E1, Eꢀ, E3 and E4.
2. Pre-requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting
cables
• The purchaser/user is urged to use only equipment which has been recommended by us
as peripheral equipment to be connected to the apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the
apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency
applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are
recommended for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for
AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission
applications, for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use shielded cables, which provide quality performance for high-frequency applications,
as connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s)
following instructions in this manual.
3. Performance level
The performance level of the apparatus is equivalent to or better than the performance level
required by these standards.
However, the apparatus may be adversely affected by interference if it is being used in an
EMC environment, such as an area where strong electromagnetic fields are generated (by the
presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse
effects of the interference on the apparatus in cases like this, it is recommended that the
following steps be taken with the apparatus being affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
ꢀ. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other
appliances.
8
Read this first! (For AG-3DA1P/AG-3DA1E)
Recommendation for Use of Genuine Panasonic Battery
(Rechargeable Battery)
Thank you for using a Panasonic product.
It has been found that counterfeit battery packs which look very similar to the genuine product are
made available to purchase in some markets. Some of these battery packs are not adequately
protected with internal protection to meet the requirements of appropriate safety standards. There is
a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not
liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure
that safe products are used we would recommend that a genuine Panasonic battery pack is used.
• Be aware that many batteries sold at extremely cheap prices or in situations where it is difficult to
verify the actual products before purchase have proven to be counterfeit.
■Batteries that may be used with this product (Correct as of August 2010)
Panasonic CGA-D54 batteries may be used with the AG-3DA1P.
Panasonic CGA-D54s batteries may be used with the AG-3DA1E.
EU
To remove the battery
Main Power Battery
(Refer to page 24 for the detail.)
Press the battery release button.
Battery release
button
Back-up Battery
• For the removal of the battery for disposal
at the end of its service life, please
consult your dealer.
3D image shooting/viewing
• Do not set a wide parallax (parallax between the left and right eyes) when shooting a 3D image.
Viewing the 3D image shot with a wide parallax may cause eyestrain or other adverse effects.
For details on the parallax, see “Adjusting the convergence point.” (Page 38)
• When viewing 3D images, observe the viewing precautions indicated in the operating instructions
of the monitor. If you continue viewing 3D images in incorrect conditions, it may cause eyestrain
or other adverse effects.
AVCCAM 3 Year Warranty Repair Program*1
Thank you for purchasing this Panasonic AVCCAM device.
Register as a user for this device to receive a special service warranty up to three years of free warranty repairs.
Customers who register as users on the website will receive an extended warranty repair valid for up to
three years.
1st year
2nd year
3rd year
2
3
4
AVCCAM device
Basic warranty
Extended warranty repair
*
*
*
*1: Please note that this extended warranty is not available in some countries/regions. *2: Not all models eligible for extended warranty coverage.
*3: The basic warranty period may vary depending on the country/region. *4: Not all repair work is covered by this extended warranty.
Free 3 years of Warranty Repairs
Make sure to save the “Registration Notice” e-mail
during the warranty period.
Purchase
AVCCAM product
Register online
within 1 month
“Registration Notice”
e-mail sent
Please note, this is a site that is not maintained by Panasonic Canada Inc. The Panasonic Canada Inc. privacy policy does not apply and is not applicable in relation to any
information submitted. This link is provided to you for convenience.
9
●SDHC Logo is a trademark of SD-3C, LLC.
●“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
●This product has been manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
●HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and/or other countries.
●Microsoft®, Windows®, and Windows Vista® are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
●Screenshots are used in accordance with Microsoft Corporation guidelines.
●IBM and PC/AT are registered trademarks of International Business Machines Corporation.
●Intel® is a registered trademark or a trademark of Intel Corporation in the United States and/or other
countries.
●Apple®, Macintosh®, and Mac OS® are trademarks of Apple Inc., registered in the United States
and other countries.
●Other model names, company names, and product names listed in these operating instructions are
trademarks or registered trademarks of their respective companies.
●This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial
use of a consumer, and no license is granted or shall be implied for any use other than the personal
uses detailed below.
– To encode video in compliance with the AVC standard (“AVC Video”)
– To decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial
activity
– To decode AVC Video that was obtained from a video provider licensed to provide AVC Video
• Additional information may be obtained from MPEG LA, LLC (http://www.mpegla.com).
– Separate license contracts must be obtained from MPEG LA where SD Memory Cards containing
information recorded with this product are to be distributed to end users for commercial purposes. “End
user” refers to persons or organizations handling such contents for personal use.
Note concerning illustrations in these instructions
• Illustrations (camera-recorder, menu screens, etc.) in these operating instructions differ slightly from
the actual camera-recorder.
References
• References are shown as (Page 00).
Terminology
• Both SD Memory Cards and SDHC Memory Cards as referred to as “SD Memory Cards” in these
operating instructions.
• Video that is created during a single recording operation is referred to as a “clip” in these operating
instructions.
10
Overview
This camera-recorder is an integrated 3D camera-recorder equipped with twin lenses in a single body.
The twin-lens system allows you to adjust the convergence point within the camera and record 3D
images with natural sense of depth.
The main features of the unit are as follows:
- Compact and lightweight, with high mobility.
- Easy 3D recording with no need for adjusting two lenses.
- Use of two SD Memory Cards allows simultaneous recording/playback of two channels (AVCHD, PH
mode).
- Two-channel HD SDI outputs (L and R channels) and HDMI (3D) output are provided for 3D video
signals.
3D image and convergence point
When shooting
When viewing a 3D image
Convergence point
3D glasses
• The illustration above is an image for explanation.
The convergence point is a point where the optical axes of the left and right lenses converge. This
indicates the reference plane when viewing a 3D image.
When shooting, adjust the convergence point by shooting the subject you want to set on the
reference plane so that the image of the subject from the left lens is completely superimposed
onto that from the right lens.
When viewing the 3D image, a subject located closer than the convergence point is displayed in
front of the screen, and a subject located farther than the convergence point is displayed behind
the screen.
11
Contents
Read this first! (For AG-3DA1P)..................2
Read this first! (For AG-3DA1E)..................5
Read this first!
(For AG-3DA1P/AG-3DA1E) .................9
Overview......................................................11
Operating precautions...............................14
Shooting
Basic shooting operations ........................30
Preparing for recording................................. 30
Formatting a card ......................................... 30
Basic shooting operation.............................. 31
Checking photos taken (REC CHECK) ........ 31
SD Memory Card access lamps................... 3ꢀ
SD Memory Card recording times................ 3ꢀ
Removing SD Memory Cards....................... 33
Protecting SD Memory Cards....................... 33
Repairing SD Memory Cards ....................... 33
Using the zoom function............................34
Shooting in progressive mode..................35
Adjusting the focus....................................36
Manual focusing ........................................... 36
Using focus assist ........................................ 36
Adjusting the brightness ...........................37
Adjusting the convergence point..............38
Tips on convergence point adjustment......... 38
Adjusting the white balance......................40
White balance adjustments .......................... 40
Using presets ............................................... 40
Black balance adjustments........................... 41
Shooting techniques for different
targets..................................................42
Low angle recording..................................... 4ꢀ
Zebra pattern................................................ 4ꢀ
Checking and displaying shooting status ..... 43
Using the USER buttons ............................. 43
Color bars..................................................... 43
Wave form monitor function.......................... 44
Adjusting the volume while shooting ............ 44
Shot mark function ....................................... 44
3D FINE function.......................................... 45
Adjusting the shutter speed......................46
Synchro scan................................................ 47
Switching Audio Input................................48
Using the built-in microphone....................... 48
Using an external microphone and audio
Before use
Precaution for use......................................16
SD Memory Cards compatible with this
product ..................................................... 17
(SD speed class 4)..................... 18
SDHC Memory Cards................................... 18
Compatibility with equipment other than
AG-3DA1 (this product)............................ 18
About AVCHD............................................... 18
Accessories ................................................19
Optional accessories .................................19
Description of parts
Description of parts....................................20
Right side and rear side ............................... ꢀ0
Left side........................................................ ꢀ1
Terminals and mounting parts ...................... ꢀꢀ
Preparation
Charging the battery ..................................23
Charging....................................................... ꢀ3
Power sources............................................24
Using the battery .......................................... ꢀ4
Using the AC adaptor ................................... ꢀ4
Turn on/off the camera...............................25
Tally lamp ....................................................25
Viewfinder ...................................................26
Using the viewfinder..................................... ꢀ6
Using the LCD.............................................. ꢀ7
Emphasizing outlines ................................... ꢀ7
Setting the calendar...................................28
equipment................................................. 48
Adjusting the recording level ........................ 49
Clip metadata..............................................50
Uploading the metadata (META DATA) ........ 51
Selecting the USER CLIP NAME recording
method ..................................................... 5ꢀ
Using the Counter ......................................53
Charging the built-in battery/Setting the
time code.............................................54
Recharging the built-in battery ..................... 54
Setting the time code.................................... 54
Specifying the time code (TC PRESET)....... 54
Setting user information ............................... 56
1ꢀ
Playback
Menu
Basic playback operations........................57
Thumbnail screen.......................................58
Basic thumbnail screen operations .............. 58
Adding shot marks to clips ........................... 59
Playback settings (PLAY SETUP)..............60
Resume playback (RESUME PLAY)............ 60
Thumbnail operations................................61
Selecting the thumbnail display method
(THUMBNAIL SETUP) ............................. 61
Deleting and protecting clips
(OPERATION).......................................... 6ꢀ
Checking clip information
(CARD FUNCTIONS)............................... 63
Useful playback functions.........................64
Fast forward/rewind...................................... 64
Next/previous clip......................................... 64
Frame-by-frame playback ............................ 65
Adjust volume............................................... 65
Viewing images on a monitor or television... 65
Checking the date and time.......................... 65
Using the setup menus..............................75
Using the menus .......................................... 75
Initializing the menu settings ........................ 76
Setup menu structure ................................77
Camera mode menu..................................... 77
Playback mode menu................................... 77
Setup menu list...........................................78
CAMERA SETUP screen.............................. 78
SW MODE screen........................................ 79
RECORDING SETUP screen....................... 80
TC/UB SETUP screen.................................. 80
AV OUT SETUP screen................................ 81
DISPLAY SETUP screen.............................. 81
CARD FUNCTIONS screen ......................... 8ꢀ
META DATA screen ...................................... 8ꢀ
OTHER FUNCTIONS screen....................... 83
PLAY SETUP screen.................................... 84
THUMBNAIL SETUP screen........................ 84
OPERATION screen..................................... 84
Reference
Editing
Before calling for service...........................85
Updating the firmware in the camera .......87
Cleaning ......................................................88
Storage Precautions...................................89
Recording format........................................90
How to handle data recorded on SD
Connecting external units .........................66
Headphones................................................. 66
External microphone .................................... 66
TV/Monitor.................................................... 67
Memory Card.......................................91
Specifications.............................................92
Index ............................................................94
Displays
Screen displays..........................................68
Regular displays........................................... 68
Main warning displays.................................. 71
Setting the DISPLAY items........................... 74
13
Operating precautions
Do not allow any water to get into the camera-
recorder when using it in the rain or snow or
at the beach.
• The battery charger may make some noise
when you are using it, but this is normal.
• Failure to heed this caution will cause the
camera-recorder or a card to malfunction (and
may result in irreparable damage).
Take precautions not to drop the camera-
recorder when moving it.
• Strong impacts may damage the camera-
recorder and cause it to stop working.
• Strong shock may lead to vertical misalignment
of the images from the two lenses.
Keep the camera-recorder away from
equipment (such as TV sets and video game
machines) that generate magnetic fields.
• Using the camera-recorder on top of or near
a TV set may cause distortion in the images
and/or sound due to the electromagnetic waves
that the set emits.
• The powerful magnetic fields generated by
speakers or large motors may damage your
recordings or distort the images.
• The electromagnetic waves emitted from a
microcomputer will adversely affect the camera-
recorder, causing the images and/or sound to
be distorted.
• If the camera-recorder is so adversely affected
by products that generate magnetic fields that
it no longer operates properly, turn it off and
remove the battery or unplug the AC adaptor
from the power outlet. Then install the battery
again or reconnect the AC adaptor. After this,
turn the camera-recorder back on.
• Handle the camera-recorder with care, securely
gripping the handle or hand strap to carry it.
Do not spray the camera-recorder with insect
sprays or other volatile substances.
• These can warp the camera-recorder or cause
the finish to come off.
• Do not leave the camera-recorder in contact
with rubber or PVC products for extended
periods of time.
After use, remove the battery and disconnect
the AC power supply cable.
Battery characteristics
This camera-recorder uses a rechargeable
lithiumion battery that uses its internal
chemical reaction to generate electrical
energy. This reaction is easily influenced by
the ambient temperature and humidity, and the
battery’s effective operating time is reduced
as the temperature rises or falls. In very low
temperatures, the battery may last only 5
minutes.
Do not use the camera-recorder near radio
transmitters or high-voltage equipment.
• Using the camera-recorder near a radio
transmitter or high-voltage equipment may
adversely affect the recorded images and/or
sound.
Protective circuitry functions if you use the
battery where it is very hot and you will have to
wait before you can use it again.
Do not allow any sand or dust to get into the
camera-recorder when using it at the beach
and other similar places.
• Sand and dust can damage the camera-
recorder or a card. (Be especially careful when
inserting or removing a card.)
Remove the battery after use.
Completely remove the battery. (The battery
continues to be used even if you have turned
the camera-recorder off.) The battery can over
discharge if you leave it in the camera-recorder
and it may become impossible to recharge it.
Battery charger and battery
• If the CHARGE lamp continues to blink even
when the battery temperature is normal, there
may be something wrong with the battery or
battery charger. Contact your dealer.
• The battery takes longer to charge when it is
warm.
Disposing of spent batteries
The battery will become unchargeable. Rather
than throwing the battery into the garbage, take it
to a store that can assist in recycling it.
• The battery charger can interfere with radio
reception so keep radios at least 1 meter away
from it.
14
What to remember when throwing memory
cards away or transferring them to others
Formatting memory cards or deleting data using
the functions of the unit or a computer will merely
change the file management information: it will
not completely erase the data on the cards.
When throwing these cards away or transferring
them to others, either physically destroy them
or use a data deletion program for computers
(commercially available) to completely erase the
data. Users are responsible for managing the
data on their memory cards.
Liquid crystal displays
• Images or letters can get burned onto the
screen of the LCD or viewfinder if they are
displayed for a long time, but you can fix this
by leaving the camera-recorder off for several
hours.
• The pixels of the LCD monitor are controlled
to obtain high precision with 99.99 % of the
effective pixels. This leaves less than 0.01 %
of pixels that may not light or may remain on all
the time. These phenomena are normal and will
have no effect on the images you shoot.
• Condensation may form if you use the camera-
recorder where temperatures fluctuate. Wipe
dry with a soft, dry cloth.
• The LCD may appear dim after immediately
turning on a cold camera-recorder, but will
brighten as the camera-recorder warms up.
Do not point the lens or viewfinder at the sun.
Doing so may damage the parts inside.
Protective caps for the connectors
Keep the protective caps fitted over any
connectors that are not being used.
15
Precaution for use
Always take some trial shots before actual shooting.
• When shooting important events (such as weddings), always take some trial shots and check that the
sound and images have been recorded properly before actual shooting.
Be sure to check and set the calendar and time zone.
• These settings affect the control and playback sequence of the recorded contents. Before making a
recording, set and check the calendar and time zone. (Page ꢀ8)
Panasonic makes no guarantees for your recordings.
• Please understand that Panasonic makes no guarantees for your recordings in cases where images
and/ or sound were not recorded as you intended due to problems with the camera-recorder or
SD/SDHC Memory Cards.
Respect copyrights
• Copyright laws forbid the use of video and audio material you have recorded for any purpose other
than your own personal enjoyment. Remember that restrictions apply to the shooting of certain
material even if it is intended for private use.
Caution regarding laser beams
• The MOS may be damaged if it is subjected to light from a laser beam.
When using the camera-recorder in locations where laser irradiation equipment is used, be careful
not to allow the laser beam to shine directly on the lens.
Media that can be used in this unit
• SD/SDHC Memory Cards can be used in this unit. For details, refer to page 17.
Mounting the camera-recorder on a tripod
• There are tripod mounting holes that are compatible with 1/4-ꢀ0UNC screws. A removable screw
spacer is installed in one of the screw holes, which is compatible with 3/8-16UNC screws when the
screw spacer is removed. Use the size that matches the diameter of the tripod’s fixing screw. To
remove the screw spacer, use a slot screwdriver.
• The tripod mounting hole is 5.5 mm deep. Do not force the tripod screw beyond this depth.
Screw spacer
Attach the tripod to the tripod hole.
16
SD Memory Cards compatible with this product
Use SD Memory Cards or SDHC Memory Cards of SD speed class 4 or above. It is recommended that
you use the Panasonic SDHC Memory Cards listed below (correct as of August ꢀ010).
• SDXC cards are not available for this product.
Card type
Recording capacity
Recording/playback
51ꢀ MB
1 GB
RP-SDV51ꢀ
SD Memory
Card
RP-SDV01G
RP-SDM01G
RP-SDV0ꢀG
RP-SDM0ꢀG
ꢀ GB
RP-SDV04G
RP-SDM04G
RP-SDW04G
RP-SDP04G
4 GB
6 GB
8 GB
RP-SDM06G
RP-SDV08G
RP-SDM08G
RP-SDW08G
RP-SDP08G
SDHC Memory
Card
RP-SDM1ꢀG
RP-SDP1ꢀG
1ꢀ GB
16 GB
RP-SDV16G
RP-SDM16G
RP-SDW16G
RP-SDP16G
RP-SDV3ꢀG
RP-SDW3ꢀG
RP-SDP3ꢀG
3ꢀ GB
• Please see our support page at the following website for the latest information not included in these
operating instructions.
• This product is compatible with SD Memory Cards formatted under the SD-standard FAT1ꢀ and
FAT16 formats, and with SDHC Memory Cards formatted under the FAT3ꢀ format.
• Only SDHC Memory Cards may be used for capacities of 4 GB or greater.
• 4 GB (or greater) memory cards without the SDHC logo are not based on the SD standard.
• Use this product to format the SD Memory Cards to be used. Formatting memory cards on computers
or other devices may cause recording to take longer than normal, or may cause cards to become
incompatible with this product. (Page 30) (Use this product to reformat any cards that have already
been formatted on computers, etc.)
• Always install the relevant special adapter when using microSD/microSDHC cards with this product.
(The product will not operate correctly if only the adapter is inserted – always insert a memory card
into the adapter first.)
• MultiMediaCards cannot be used with this product.
• SD/SDHC Memory Cards with a memory size from 8 MB to 3ꢀ GB can be used to read metadata.
17
Precaution for use (continued)
(SD speed class 4)
This refers to a class 4 speed standard (SD speed class) for the continuous writing of data between
SD-compatible devices and SD Memory Cards, as designated by the SD standards.
When the use of an SD speed class 4 card is recommended for SD-compatible products, this indicates
that stable recording operation can be achieved when using SD Memory Cards of class 4 and above.
Cautions for usage
• Do not allow dirt, water, or other substances to come into contact with the connector part on the
reverse of the card.
• Do not leave the card in the following places:
– In direct sunlight or in places of high humidity, e.g. close to heating equipment
– In highly humid or dusty locations
– In locations with high variations in temperature (condensation may appear on card)
– In places subject to static electricity or electromagnetic waves
• Store cards in bags or cases after use.
SDHC Memory Cards
●SDHC Memory Cards cannot be used with non-SDHC-compatible equipment.
●Ensure that all equipment is SDHC-compatible when using card with other
devices.
To play back 3D images shot with this product, use the PB mode of this product.
Note the following when you play back clips of either the left or right channel of
the 3D image.
Compatibility with equipment other than AG-3DA1 (this product)
●Recorded video cannot be used with non-AVCHD-compatible equipment.
For details, please see your product’s operating instructions.
●Recorded video cannot be played back on non-compatible (non-AVCHD-compatible) equipment.
●Playback may not always be possible on all AVCHD-compatible equipment.
Clip imformation such as meta data and 3D information cannot be read with AVCHD-compatible
equipment other than this product.
●If you perform additional recording or delete clips with another equipment, the 3D information is lost
and playback or recording is no longer possible with the product.
About AVCHD
●AVCHD is a standard for the recording and playback of highly detailed, high-definition video.
●Video is compressed in the MPEG-4 AVC/H.ꢀ64 formats, and audio is recorded in Dolby Digital.
18
Accessories
Battery
Battery charger / AC power supply cables
AG-3DA1P
AG-3DA1E
(For the U.K.)
(For areas other than
the U.K.)
For part numbers
for the battery, see
“Optional accessories”
below.
Eye cup
AC adaptor / AC power supply cables
AG-3DA1P
AG-3DA1E
(For the U.K.)
(For areas other than
the U.K.)
Microphone holder
Microphone holder
screws
Microphone holder
adaptor
CD-ROM
Length 6-mm (2)
Length 12-mm (2)
The following accessories are attached to the unit.
Lens cap
INPUT terminal
cover (2)
Screw spacer
• After unpacking, dispose of the AC power supply cable caps and packing materials properly.
• Please consult a retailer when purchasing additional accessories.
Optional accessories
• XLR microphone
AG-MCꢀ00G
• Battery
CGA-D54 (7.ꢀ V, 5400 mAh: equivalent to accessory battery for the AG-3DA1P)
CGA-D54s (7.ꢀ V, 5400 mAh: equivalent to accessory battery for the AG-3DA1E)
19
Description of parts
Right side and rear side
4
5
6
7
8
9
10
11
1
2
CAMERA
PB
14
POWER
15
ON
OFF
HA
1
ND
2
3
LE ZOOM
OF
F
ON
3
L
R
.
12
13
16
1718
1
2
3
4
5
6
7
8
9
POWER/Mode selector switch (Page 24)
Mode lamps (Pages 31 and 57)
START/STOP button (Page 31)
REC CHECK button (Page 31)
Zoom button (Page 34)
10 Built-in stereo microphone (Page 48)
11 Tally lamp (Front) (Page 25)
12 Right lens
13 Left lens
14 Viewfinder (Page 26)
HANDLE ZOOM switch (Page 34)
REC selector switch (Page 42)
Handle zoom button (Page 34)
Handle START/STOP button (Page 42)
15 SD Memory Card slot cover (Page 30)
16 Tally lamp (Rear) (Page 25)
17 Battery compartment (Page 24)
18 Battery release button (Page 24)
ꢀ0
Left side
4
5
6
7
8
9
10
19
20
25
MENU
EXEC
21
22
PUSH
ENTER
LINE
INPUT
MIC
LINE MIC
INPUT
MENU
EXEC
1
2
PUSH
ENTER
AUDIO MON/ADV
AUDIO MON/ADV
1
23 24
26
FOCUS
BAR
1
2
3
2
3
FOCUS
PUSH
AUTO
USER
BARS
SHUTTER
SPEED SEL
∞
CH
1
SELECT CH
INT(L)
2
1
INPUT
ON
OFF
2
INT(R)
INPUT
INPUT
INPUT
1
2
2
CH
1
AUDIO
PUSH
TURN
CH
2
WHITE BAL
DIAL
DISP/MODE CHK
CONV.
MIC POWER +48V
B
AUDIO
A
PRST IRIS
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
AWB
11
27
28
29
30 31
12 13 14 15
16
17 18
1
2
3
4
5
6
7
8
9
Built-in speaker (Page 65)
Focus ring (Page 36)
Zoom ring (Page 34)
17 LCD monitor (Page 27)
18 OPEN button (Page 27)
19 MENU button (Page 75)
INPUT 1/2 (LINE/MIC) switches (Page 48)
PUSH AUTO button (Page 36)
20 EXEC button (Pages 45 and 62)
21 Operation lever (Page 75)
FOCUS BAR button (Page 36)
22 AUDIO MON/ADV buttons (Pages 44 and
65)
button (Page 36)
∞
23 CH1, CH2 SELECT switches (Page 48)
24 BARS button (Page 43)
USER 1/2 buttons (Pages 43 and 79)
3D GUIDE button (Page 38)
25 SHUTTER, SPEED SEL +/- buttons
(Page 46)
10 Diopter adjustment dial (Page 26)
11 AWB button (Page 40)
26 INPUT 1/2 switches (MIC POWER +48V)
(Page 48)
12 IRIS/CONV. dial (Pages 37 and 38)
13 WHITE BAL switch (Page 40)
27 COUNTER - RESET buttons (Page 53)
28 MIX button (Page 38)
14 DIAL (IRIS/CONV.) selector switch (Pages
37 and 38)
29 EVF DTL button (Page 27)
30 ZEBRA button (Page 42)
31 WFM button (Page 44)
15 DISP/MODE CHK button (Page 43)
16 AUDIO LEVEL control knobs (CH1, CH2)
(Page 49)
ꢀ1
Description of parts (continued)
Terminals and mounting parts
1
2
3
4
HD SDI
1(L)
8
9
10
11
CONV.
2(R)
CAM REMOTE
FOCUS IRIS
ZOOM S/S
7
5
6
1
2
3
4
Accessory mounting hole
Light shoe
10 Headphone jack (3.5 mm stereo mini jack)
(Page 66)
11 CAM REMOTE jack
*
Microphone shoe (Page 66)
CONV. (2.5 mm super mini jack)
You can connect a remote control unit
(optional) to control the convergence point
adjustment (adjustment of the reference plane
for the 3D image).
Audio INPUT 1/2 terminals (XLR 3 pin)
(Page 48)
5
6
Card slot cover OPEN lever (Page 30)
SD Memory Card slots and access lamps
(Page 32)
FOCUS/IRIS (3.5 mm mini jack)
You can connect a remote control unit
(optional) to control the FOCUS and IRIS
(aperture).
7
8
9
Tripod hole (Page 16)
HD SDI L/R terminals (Page 67)
HDMI OUT terminal (Page 67)
ZOOM S/S (2.5 mm super mini jack)
You can connect a remote control unit
(optional) to control zoom and start/stop of
recording.
Do not connect any equipment except the
*
remote controller to the remote control jack.
Connecting any equipment other than the
remote control may cause the image brightness
to change and/or the images to appear out of
focus.
ꢀꢀ
Charging the battery
Charging
■Charging time and available recording time
Before using the battery, fully charge it with
the battery charger.
(Approx.)
Keep a spare battery with you.
Battery
model
(included)
Maximum
continuous
recording time
Voltage/ Charging
capacity
time
Align the battery with the
marking on
1
the battery charger, place it flat, slide it
in the direction shown below and press
firmly.
CGA-D54
(AG-3DA1P)
CGA-D54s 5400 mAh
(AG-3DA1E)
Approx.
330
7.ꢀ V/
Approx.
180 minutes
minutes
• The times apply when the ambient operating
temperature is ꢀ0 °C (68 °F) and humidity
is 60 %. Charging may take longer at other
temperatures and humidity levels.
Press firmly.
■Remaining battery capacity displays
The battery display will change
→
→
→
as battery
capacity decreases.
will be displayed in
red when the battery is empty.
(For details on the remaining battery capacity
displays: Page 70)
Connect the AC power supply cable.
Connect the AC power supply cable in the
2
order
and
.
• The POWER lamp and CHARGE lamp
on the battery charger light, and charging
begins.
• If the CHARGE lamp does not light when
attached, detach the battery and then
attach it again.
• Keep metal objects (such as necklaces
and hairpins) away from the battery.
Short-circuiting may occur across the
terminals, causing the battery to heat up,
and you may seriously burn yourself if
you touch the battery in this state.
• The battery becomes hot while it is being
used or charged. The camera itself also
becomes hot during use.
Insert it all
the way in.
CHARGE
• Discharge the battery before storing it.
• When storing it for an extended time, charge
it at least once a year, use up its charge in
the camera, and then store it again.
• If the battery is extremely hot or cold, the
CHARGE lamp will blink several times before
charging starts.
• If the CHARGE lamp continues to blink even
when the battery temperature is normal,
there may be something wrong with the
battery or battery charger. Contact your
dealer.
POWER
• When the battery is charged, the CHARGE
lamp on the battery charger goes out.
Slide the battery and remove it.
3
• The battery takes longer to charge when it
is warm.
• The battery charger can interfere with radio
reception so keep radios at least 1 meter
away from it.
• The battery charger may make some noise
when you are using it, but this is normal.
ꢀ3
Power sources
Using the battery
Installation
Removal
Insert the battery until it clicks into place.
Set the POWER/Mode selector switch to
OFF, and check that the mode lamps are
off. (Page 25)
1
2
Remove the battery while pressing the
battery release button.
• Support the battery with your hand to
ensure that it will not fall.
Mode lamps
CAMERA
PB
POWER
ON
M
D
E
OFF
Battery release button
Using the AC adaptor
Installation
Removal
Insert the DC cable’s battery connector
until it clicks into place.
Set the POWER/Mode selector switch to
OFF, and check that the mode lamps are
off. (Page 25)
1
1
Connect the AC power supply cable.
Connect the AC power supply cable in the
2
Remove the DC cable’s battery connector
while pressing the battery release button.
2
3
order
and
.
Disconnect the AC power supply cable
from the power outlet.
DC cable’s battery
connector
CAUTION:
• Disconnect the AC power supply cable from
the power outlet when the unit is not going
to be used.
• When the AC power supply cable is
disconnected from the power outlet, the
power lamp on the AC adaptor remains
lit for a while then shuts off. This is not a
malfunction.
Insert it all
the way in.
ꢀ4
Turn on/off the camera
While pressing the lock release button, move the
POWER/Mode selector switch to ON or OFF.
Turn on the camera:
The mode lamp (CAMERA) lights red (CAMERA
mode) and the camera is now in the recording
pause mode.
Mode lamp
(CAMERA)
Turn off the camera:
The mode lamp (CAMERA) goes out.
CAMERA
PB
POWER
ON
OFF
Lock release
button
Tally lamp
The tally lamp can be illuminated during
recording by setting the REC LAMP item on the
OTHER FUNCTIONS screen (Page 83) to any
setting other than OFF.
The tally lamp will flash in any of the following
circumstances.
• Recording error has occurred
(flashes 4 times per second)
• Battery is empty (flashes 4 times per second)
• Available SD Memory Card capacity is low
(flashes 4 times per second)
Tally lamp
(rear)
• Problem with focus function
(flashes 4 times per second)
• Remaining memory capacity of the SD Memory
Card is less than ꢀ minutes (flashes once per
*
second)
Tally lamp
(front)
Time for a rough guide
*
ꢀ5
Viewfinder
This camera has two viewfinders; one is a
miniature LCD in the viewfinder and the other is a
retractable 3.ꢀ-type LCD.
Use the viewfinder that best suits the application
and shooting conditions.
• The brightness and hue may differ between the
images appearing on the viewfinder and LCD
monitor and those displayed on a TV monitor.
To see how the final images will appear, check
them on a TV monitor.
Do not allow the eyepiece of the viewfinder
to remain in direct contact with sunlight or
other strong light sources.
• Internal components may be damaged and
fire may be caused if light accumulates
through the lens.
Fitting the eye cup
Attach the eye cup by aligning the ridges on the
eye cup holder with the grooves on the eye cup
and fitting them together.
• Turning the eye cup after attaching it may
cause the eye cup holder to come off. If the
eyecup holder does come off, see “Cleaning
the Viewfinder” (Page 88) for details on how to
refit it.
Using the viewfinder
Set the POWER/Mode selector switch
to ON (Page 25) and check that images
appear in the viewfinder.
1
CAMERA
PB
Eye cup holder
POWER
ON
OFF
Eye cup
Adjust the viewfinder’s angle so that the
screen is positioned where it is easiest to
see.
2
• You can move the viewfinder out to about
90° perpendicular to the camera.
Align the ridges with the grooves.
Adjust the diopter adjustment dial so
that you can see the characters on the
viewfinder screen clearly.
3
Diopter adjustment dial
Eye piece
ꢀ6
Using the LCD
Emphasizing outlines
Set the POWER/Mode selector switch to
ON. (Page 25)
Emphasizing the outlines of the images you see
in the viewfinder or on the LCD makes it easier
to focus.
Emphasizing the outlines does not effect the
images you shoot.
1
Hold down the OPEN button and open the
LCD monitor.
• It can open out to 90°. Do not try to open it
further as this will damage the camera.
2
In CAMERA mode, press the EVF DTL
button.
1
“EVF DTL ON” appears on the screen for
about ꢀ seconds.
90°
BARS
CH 1
SHUTTER
SPEED SEL
SELECT CH 2
1
INPUT
2
INT(L)
INT(R)
INPUT
ON
INPUT
INPUT
1
2
2
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
OPEN button
EVF DTL
ZEBRA
Position the LCD monitor where it is easiest
to see.
3
EVF DTL button
• The monitor can be rotated 180° toward
the lens and 90° toward you.
Press the EVF DTL button again to return to
the original display. “EVF DTL OFF” appears
on the screen for about ꢀ seconds.
180°
90°
• Do not apply unnecessary force to the
open LCD. This can damage the camera.
• Ensure the LCD is fully closed.
ꢀ7
Setting the calendar
The CLOCK SET value is recorded in the
contents (clip). Before carrying out recording, be
sure to check and set CLOCK SET and TIME
ZONE.This shows you how to adjust the calendar
to 17:ꢀ0 on ꢀ5 December, ꢀ010.
Tilt the Operation lever in the direction
and select YES in the CLOCK SET item
on the settings menu OTHER FUNCTIONS
screen.
5
CLOCK SET
REC LAMP
Set the camera’s POWER/Mode selector
switch to ON. (Page 25)
1
CLOCK SET
TIME ZONE
YES
NO
SYSTEM FREQ
SYSTEM INFO
Press the MENU button.
• Menu operation (Page 75)
2
Select the TIME ZONE item on the settings
3
menu OTHER FUNCTIONS screen, and
push the Operation lever (or tilt lever in
direction).
Tilt the Operation lever in the
directions and set to DEC.
6
7
CLOCK SET
TIME ZONE
REC LAMP
CLOCK SET
TIME ZONE
+00:00
D E C 13 2010 23 01
SYSTEM FREQ
SYSTEM INFO
Tilt the Operation lever to the direction
to change to the next item, and set to 25 by
Pushing the Operation lever twice brings
up the setting screen. Tilt the Operation
4
tilting in the
directions.
lever in the
directions to set the time
CLOCK SET
difference from Greenwich Mean Time,
and push the Operation lever again.
Factory default setting is +00:00.
D E C 25 2010 23 01
TIME ZONE
TIME ZONE
+00:00
Repeat steps 6 and 7 to set the remaining
items.
8
CLOCK SET
D E C 25 2010 17 20
• The date can be set to any date between
1 January, ꢀ001 and 31 December, ꢀ039.
• Time is displayed in ꢀ4-hour format.
ꢀ8
When settings are complete, push
the Operation lever, select YES on the
confirmation screen, and push the
Operation lever again.
9
CLOCK SET
CLOCK
SET?
YES
NO
• The clock can vary in accuracy so check that
the time is correct before shooting.
• When using the camera overseas, do not
set the CLOCK SET option to the local time,
but instead enter the time difference from
Greenwich mean time according to TIME
ZONE.
ꢀ9
Basic shooting operations
Preparing for recording
• When an SD Memory Card is formatted,
all data recorded on the card will be
erased and will not be restorable.
Save all important data to your computer.
• If “CHECK CARD” is displayed on the
viewfinder or the LCD monitor, please
remove the SD Memory Cards and insert
them again.
2
• Mosaic-like noise may appear on the
playback screen under the following shooting
conditions:
CAMERA
3
1
� When there are complex patterns in the
background
PB
POWER
ON
OFF
� When the camera is moved in large
motions or when it is moved very quickly
�
When a fast-moving subject has been
recorded
Insert the connector part in
the direction shown here,
and push until the card clicks
firmly into place.
Lock release
button
Formatting a card
If you use SD Memory Cards for the first time for
shooting with this camera, format the cards as
follows:
While pressing the lock release button,
turn the POWER/Mode selector switch to
OFF.
1
• Be sure to format the two cards simultaneously
using this product.
• Check that the mode lamps are off.
Tilt the viewfinder upwards, and open the SD
Memory Card slot cover by sliding the OPEN
lever to the right.
2
3
While pressing the lock release button,
turn the POWER/Mode selector switch to
ON.
1
Fully insert two SD Memory Cards into the
card slots.
• Be sure to insert two SD Memory Cards.
• Use SD Memory Cards of the same type
and capacity.
•
Check that the mode lamp (CAMERA) is
lighted red.
Press the MENU button.
2
3
Tilt the Operation lever in the
directions to select CARD FUNCTIONS,
and push the Operation lever (or tilt in the
direction).
Close the SD Memory Card slot cover.
• Ensure that the cover firmly clicks into
place.
4
• Do not perform any of the following
operations while the SD Memory Card
access lamp is flashing.
Performing these operations may damage
the SD Memory Card or its contents, or
cause the camera to fail to operate correctly.
- Opening the card slot cover and removing
the SD Memory Card
Confirm that CARD FORMAT is selected,
and push the Operation lever.
4
5
Tilt the Operation lever in the
directions to select whether or not
to format (YES or No), and push the
Operation lever.
• By selecting YES, SD Memory Cards will
be formatted. Proceeding will erase all data
from the cards.
• If only one SD Memory Card is inserted,
CAN NOT OPERATE PLEASE INSERT
THE TWO CARDS is displayed. Be sure to
insert two cards.
- Switching off the power
- Shaking or striking the camera
• Always format SD Memory Cards that have
been used in other devices when first using
them with this camera. (below)
• If the system frequency of the camera
is changed, the SD Memory Card will no
longer be able to be used. Such cards
may be used again by formatting them
with the current SYSTEM FREQ settings.
30
Basic shooting operation
• The images shot from when shooting starts
until it is stopped are recorded as one clip.
• When recording is paused after a short
period, a small amount of time may be
required after pressing the START/STOP
button to stop recording before writing to the
SD Memory Card is terminated.
Mode lamp
(CAMERA)
1
CAMERA
PB
POWER
ON
OFF
This means that operations cannot be
accepted if the START/STOP button is
pressed immediately.
Lock release
button
• The camera will read information from the
SD Memory Card immediately after the card
is inserted. Press the START/STOP button to
begin recording after PAUSE is displayed in
the operation status display. (Page 70)
• The camera’s factory default setting is
1080/60i recording (AG-3DA1P) or 1080/50i
recording (AG-3DA1E).
(To view current setting status: Page 43)
• The upper limit for the number of clips which
can be recorded on a single SD Memory
Card is ꢀ00. (However, this number may
exceed ꢀ00 clips at times such as when
shooting immediately after the POWER/
Mode selector switch has been set to ON.)
CAMERA
3
PB
POWER
ON
OFF
While pressing the lock release button,
turn the POWER/Mode selector switch to
ON.
Check that the mode lamp (CAMERA) is
lighted red (CAMERA mode).
1
2
•
Adjust the focus, brightness, white
balance, and convergence point.
•
Focus adjustment (Page 36)
Checking photos taken (REC CHECK)
• Brightness adjustment (Page 37)
• White balance adjustment (Page 40)
• Convergence point adjustment (Page 38)
Press the REC CHECK button while recording is
paused. The last two seconds of video and audio
will be played, and the camera will then return to
the recording pause mode.
Press the START/STOP button (Red) to
start shooting.
3
• Only the POWER/Mode selector switch is
operable during REC CHECK.
• Press again to return the camera to the
recording pause mode.
• The REC CHECK images are also recorded
when a device is connected to the camera and
backup images have been recorded.
• Use the handle START/STOP button to
make it easier to shoot from low angles.
(Page 4ꢀ)
• The REC CHECK function does not work when
PB has been selected as the operation mode.
• This function also does not work if the REC
FORMAT has been changed or if the camera
has been set to CAMERA mode after having
switched to PB mode after recording.
The handle START/STOP button can be
enabled (ON) and disabled (OFF) with the
handle REC selector switch.
• Shooting is not possible when a menu
screen is displayed. First, close the menu
screen, and then press the START/STOP
button.
• Shooting stops when the SD Memory Card
slot cover is opened during shooting.
31
Basic shooting operations (continued)
SD Memory Card access lamps
SD Memory Card recording times
Each SD Memory Card access lamp indicates
the status of the SD Memory Card inserted in the
corresponding SD card slot.
• Total available recording times (approx.) when
using SDHC Memory Cards manufactured by
Panasonic
Recording mode PH
(19ꢀ0 × 1080 pixels or
1ꢀ80 × 7ꢀ0 pixels)
SDHC Memory
Card capacity
Illuminated:
Reading/writing possible
Flashing (fast):
4 GB
8 GB
16 GB
3ꢀ GB
Approx. ꢀ1 min
Approx. 45 min
Approx. 90 min
Approx. 180 min
Verifying card/inspecting card for possible
defects
Flashing (slow): Accessing card
Off: No card inserted/unformatted, incompatible
card inserted or card full
• This product allows PH recording mode only.
• The quality of AVCCAM recording modes are
PH>HA>HG>HE in the order of high to low
quality.
• Use an SD Memory Card of SD speed class 4
or above. Recording cannot be completed on
SD Memory Cards of lower speed classes.
•
This camera uses the VBR recording system.
“VBR” stands for Variable Bit Rate, and it refers to
a system in which the bit rate (volume of data per
given time period) varies automatically depending
on the subject which is being shot. This means
that the recording times will be shorter when fast-
moving subjects have been recorded.
•
Times displayed include time needed for
processing, etc. – actual available recording times
will be slightly shorter.
SD Memory Card access lamps
• Repeatedly recording or deleting images over
and over again may reduce the recording time
on the SD Memory Card. In such cases, format
the SD Memory Card using the camera. When
a card is formatted, all of its recorded data
will be erased, and it will not be subsequently
possible to restore this data. Save any valuable
data on your PC prior to formatting.
3ꢀ
Removing SD Memory Cards
Protecting SD Memory Cards
Tilt the viewfinder upwards, and open the
SD Memory Card slot cover by sliding the
OPEN lever to the right.
Move the write-protect switch on the SD Memory
Card to the “LOCK” position to prevent recorded
contents being accidentally erased from the card.
1
• Ensure that the SD Memory Card access
lamps are not flashing before opening the
cover.
Write-protect
switch
Press the center of the SD Memory Card
so that it pops out slightly, and pull the
card straight outwards.
2
Repairing SD Memory Cards
Never remove the SD Memory Card or
disconnect the battery or DC cable’s battery
connector while the SD Memory Card access
lamp is flashing, as doing so may damage the
SD Memory Card. In the event that the SD
Memory Card has been removed while the SD
Memory Card access lamp was flashing, or
that the battery or DC cable’s battery connector
has been disconnected during recording or
the recording finalization process, a repair
verification screen will be displayed the next time
the power is switched on in order to allow errors
to be repaired.
1
SD Memory Card
access lamps
2
In this case, use the AVCCAM Restorer contents
repair software to repair the errors.
• Do not remove the SD Memory Card
or switch off the power in the following
circumstances. Doing so may damage your
SD Memory Card.
1) While the SD Memory Card access lamp
is still flashing after an SD Memory Card
has been inserted.
ꢀ) While the SD Memory Card access lamp
is flashing such as during recording or
during recording finalization.
• It is recommended that you note “Right” or
“Left” on the SD Memory Cards. If the left
and right SD Memory Cards are inserted in
the wrong respective slots, CHECK CARD
LEFT/RIGHT is displayed on the viewfinder
and LCD monitor.
33
Using the zoom function
This camera has an approximately 5.6 × optical
zoom function. Zoom with the zoom button or the
zoom ring.
HANDLE ZOOM switch
Handle zoom button
Zoom button
Zoom button
Zoom ring
Using the zoom button, you can perform the
motor-driven zoom.
T:
Zoom in
W: Zoom out
Gently press the zoom button on the hand strap
side to zoom slowly, firmly press to zoom faster.
Handle zoom button
You can change the zoom speed on the handle
zoom button by selecting one of three speeds
with the HANDLE ZOOM switch.
Set the HANDLE ZOOM switch speeds by going
to the setup menus, SW MODE screen, HANDLE
ZOOM. (Page 79)
Zoom ring
Using the zoom ring, you can perform manual
zooming.
• During zooming, the image may move
horizontally in small motions. This
phenomenon is caused by the camera’s
control action to keep the convergence
point constant, and it does not indicate a
malfunction.
34
Shooting in progressive mode
Selecting 1080/30P and 1080/ꢀ4P (when
SYSTEM FREQ is set to 59.9 Hz) , or 1080/ꢀ5P
(when SYSTEM FREQ is set to 50 Hz) in the
REC FORMAT item (Page 80) on the setting
menu RECORDING SETUP screen enables
shooting in progressive mode.
Note the following when shooting in
progressive mode.
• Set the shutter speed to 1/50 (OFF) for best
results.
• There may be a slight delay to the start
of recording when you use the ꢀ4P mode
because 4 frames are recorded at a time.
(Only when SYSTEM FREQ is set to 59.9
Hz)
30P mode (when SYSTEM FREQ is set to 59.9
Hz):
Shoot 30 frames a second in the progressive
mode.
For output and recording, the 30-frame-per-
second signal is converted to 60-field-per-
second interlace.
This mode gives you high quality images.
30 P A B C D E F G H I J
AoAeBoBeCoCeDoDeEoEe Fo FeGoGeHoHe Io Ie Jo Je
60 i
24P mode (when SYSTEM FREQ is set to 59.9
Hz):
Shoot ꢀ4 frames a second in the progressive
mode.
The video signal will be recorded natively.
25P mode (when SYSTEM FREQ is set to 50
Hz):
Shoot ꢀ5 frames a second in the progressive
mode.
For output and recording, the ꢀ5-frame-per-
second signal is converted to 50-field-per-
second interlace.
This mode gives you high quality images.
25 P A B C D E F G H I J
AoAeBoBeCoCeDoDeEoEe Fo FeGoGeHoHe Io Ie Jo Je
50 i
35
Adjusting the focus
Manual focusing
Using focus assist
Pressing the FOCUS BAR button displays the
focus bar indicating the focus adjustment on the
viewfinder or LCD monitor. Adjust the focus so
that the bar becomes as long as possible.
Focus ring
FOCUS BAR button
PUSH
PUSH AUTO button
button
∞
PUSH
Turn the focus ring by hand to adjust the focus
manually.
• Press the FOCUS BAR button to make the
focus bar disappear.
Temporarily switching to auto focus
The camera will focus automatically while you
press down the PUSH AUTO button.
• The correct focus may not be obtained with
auto focusing, depending on the condition of
the subject. In this case, use manual focusing.
• Auto focus may not work properly if there is
flickering. Select a shutter speed suited to the
ambient light. (Page 46)
• If the auto focus mode is set with any format
except 60i and 60P (when SYSTEM FREQ is
set to 59.9 Hz), or 50i and 50P (when SYSTEM
FREQ is set to 50 Hz), controlling the focus will
take slightly longer than in the normal focus
mode.
Adjusting the focus to infinity
Press the ∞ button to focus the camera to infinity.
MF95 is displayed on the viewfinder and LCD
monitor.
36
Adjusting the brightness
PUSH
IRIS/CONV. dial
DIAL (IRIS/CONV.)
selector switch
Set the DIAL (IRIS/CONV.) selector switch
to IRIS.
With this setting, the camera will adjust the
image brightness by controlling the aperture
of the lens iris and gain according to the
setting of the IRIS/CONV. dial.
1
2
Turn the IRIS/CONV. dial to adjust the
brightness.
To get a brighter image when the lens
aperture is OPEN, the camera will enter the
gain adjustment automatically.
• The adjusted iris and gain values are
displayed on the screen.
0dB
F2.0
• Set the direction of the IRIS/CONV. dial and
aperture control in the setup menus, SW MODE
screen, IRIS DIAL. (Page 79)
When this camera’s lens aperture is open, the
F-value will be F1.8 when the lens zoom is set
to maximum wide-angle (W), and Fꢀ.4 when
set to maximum telescopic (T).
37
Adjusting the convergence point
3D guide function
If you press the 3D GUIDE button, the viewfinder
and the LCD monitor display a guide for the
distance range within which the camera can
shoot the subject so as to comfortably reproduce
a 3D image. The 3D guide display (Page 69)
changes as follows each time you press the 3D
PUSH
GUIDE button: no display
Guide display 1
Guide display ꢀ no display…
IRIS/CONV. dial
DIAL (IRIS/CONV.)
selector switch
When shooting, select the guide display
according to the size of monitor you intend to use
for viewing.
Guide display 1 (3D indication in white):
Target monitor screen size is less than
77-type.
Guide display 2 (3D indication in green):
Target monitor screen size is 77-type or
greater.
Set the DIAL (IRIS/CONV.) selector switch
to CONV.
With this setting, the camera will adjust the
convergence point (depth of the reference
plane for the 3D image) according to the
setting of the IRIS/CONV. dial.
1
2
Turn the IRIS/CONV. dial to adjust the
convergence point.
Tips on convergence point
adjustment
PUSH
Using the MIX button
If you press the MIX button, the image from
the left lens and that from the right lens are
superimposed on the LCD monitor and viewfinder
(MIX image).
Turn the IRIS/CONV. dial so that the outline of the
subject at the reference plane from the left lens is
completely aligned with that from the right lens.
3D GUIDE button
• If you shoot a subject beyond the distance
range shown by the guide display, a double
image or strangeness feeling may be
produced, or the shot image may not be
reproduced as a 3D image correctly.
• If the subject is outside the distance range
shown by the guide display, readjust the
convergence point so that the subject goes
within the distance range of the guide
display.
BARS
SHUTTER
SPEED SEL
CH 1
SELECT CH 2
1
INPUT
2
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
ON
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
Convergence display
EVF DTL
ZEBRA
If you set CONVERGENCE to ON, on the setup
menu DISPLAY SETUP screen (Page 81), the
convergence display indicates the distance
between the camera and the adjusted reference
plane as C00 to C99. The larger the number, the
greater the distance to the reference plane.
MIX button
Press the MIX button again to display the
image shot by the left lens only.
• The left and right images will not be perfectly
aligned if the subject is located at a distance
of less than ꢀ.ꢀ m.
• The MIX image does not affect the recorded
image.
• The MIX image is cancelled when the
display status is changed, for example,
when a menu is changed or REC CHECK is
performed.
C50
38
What is convergence point adjustment?
Parallactic angle
in depth
• What is parallax?
Convergence point
Parallactic angle
Left-lens image
⇒ A human’s stereoscopic viewing takes advantage of
the brain’s ability to process information from the left
and right eyes of two images seen from their respective
perspectives. The misalignment of the two images is called
binocular parallax.
Mainly binocular parallax is used by 3D equipment to
create the feeling of stereoscopic images. When shooting,
the images from the left and right lenses are misaligned
because of the difference in the positions of the lenses
as well as in the directions of the optical axes. This
misalignment (called parallax) changes according to the
distance of the subject being shot (illustration at right).
If parallax is excessive, it is difficult to fuse the two images
within the brain. This may produce a double image, create
a feeling of strangeness, etc., causing eyestrain.
Limiting the parallax appropriately during shooting is
important for comfortable 3D viewing.
Parallactic angle
for pop out
Right-lens image
• Are there guidelines for appropriate parallax?
Parallatctic
angle in depth
⇒ There are two guidelines for parallax.
A Parallactic angle for pop out: 1 degree or less
A parallactic angle is produced between the left and right
lenses and the subject (illustration at right). It also changes
according to the distance of the subject being shot.
It is usually said that a parallactic angle for pop out within 1
degree is appropriate for comfortable 3D viewing.
Assuming that people view 3D images from a distance
three times the effective height of the screen, a parallactic
angle of 1 degree corresponds to misalignment of
approximately 3 % the effective width of the screen. This
leads to one of the guidelines for parallax, which is to limit
horizontal misalignment to within 3 % the effective width of
the screen.
Parallactic angle for pop out
• Extreme parallax between left and
right images is demonstrated in the
illustration above.
B Parallax in depth: 50 mm or less
■Parallax for pop out
Parallax: Approx. 3 % or less
(any screen size)
Parallax in depth is created when an image from the right
lens is displayed to the right and an image from the left
lens to the left on the screen.
If the value of this parallax exceeds the pupil distance of a
viewer, it will cause eyestrain.
In consideration of individual differences of viewers such
as age and pupil distance, setting parallax to within 50 mm
is preferable.
Parallax in depth is related to screen size. For a 16:9
screen, if the screen size is 77-type or less, limiting
parallax to within 3 % the effective width of the screen
means that parallax in depth will not exceed 50 mm. If the
target screen size is 103-type, limit parallax to ꢀ.ꢀ %. For a
ꢀ00-type screen, limit parallax to 1.1 %.
■Parallax in depth
For a screen of 77-type or less
Parallax: Approx. 3 % or less
• How to operate this camera
⇒ The 3D guide function of this camera (Page 38) provides
a rough guide of distance ranges from the subject for
achieving appropriate parallax in two cases: for an intended
screen size of 77-type or less, and for ꢀ00-type. Referring
to the guide, change the layout of the subject or adjust the
zoom and convergence, so that the subject can be shot
within the distance range shown by the 3D guide function.
Check the parallax value (% effective screen width), using
a monitor.
For a screen of 77-type or more
Parallax: 50 mm or less
39
Adjusting the white balance
In order to reproduce the white accurately, adjust
the ratio between the three RGB primary colors.
If the white balance is not adjusted properly,
not only will the white be reproduced poorly but
the color tones of the entire screen will also be
downgraded. When you are shooting in manual
mode, readjust the white balance whenever
lighting conditions change.
Hold down the AWB button for a while.
The following messages appear on the
screen.
4
Message during adjustment
AWB ABB Ach ACTIVE
*
• The camera performs the white balance
adjustment and the black balance
adjustment in sequence. The adjustment
will be finished in a few seconds.
You can save adjustments and reselect them by
setting the WHITE BAL switch to A or B.
You can also use the preset values.
Use the settings to suit the shooting conditions.
Message after adjustment
AWB ABB Ach END
*
• An error message appears on the screen
when white balance adjustment is not
possible.
L
SE
D
EE
SP
R
TE
UT
SH
RS
BA
2
P
U
T
I
N
1
N
H
2
O
C
E
C
T
R
T
)
2
F
F
E
L
N
N
T
(
P
U
O
S
I
I
N
(
L
)
R
+
4
8
V
T
I
B
A
Message when adjustment cannot be
done
AWB Ach NG
*
AWB button
WHITE BAL switch
Bch when the WHITE BAL switch is set to
*
B.
White balance adjustments
Using presets
Set the shutter speed. (Page 46)
1
2
Use this feature when you have no time to make
white balance adjustments.
Place a white pattern in a location with the
same lighting conditions and light source
as the subject, then zoom in and fill the
whole screen with white.
Something white (a white cloth or wall) near
the subject can be used instead.
• Do not include bright spotlights in your
shot.
Set the WHITE BAL switch to PRST.
1
The current white balance value appears.
• White balance values 3ꢀ00 K and 5600 K
are preset in the PRST position.
Guide to the preset values
P3.ꢀK (3ꢀ00 K): halogen light
P5.6K (5600 K): outdoors
Set the WHITE BAL switch to A or B
(whichever one you want to save the
adjustment in).
3
Press the AWB button.
White balance switches between 3ꢀ00 K and
5600 K.
2
40
Black balance adjustments
In order to reproduce the black accurately, adjust
the zero level of all three RGB primary colors.
If the black balance is not adjusted properly,
not only will the black be reproduced poorly but
the color tones of the entire screen will also be
downgraded.
It is not normally necessary to adjust the black
balance. Adjust it when:
• You use the camera for the first time.
• You use the camera after not using it for a long
time.
• The ambient temperature changes greatly.
• You switch to the normal (OFF) shutter speed
or to slow shutter.
• You switch between the progressive and
normal (60i ) modes.
*
50i when SYSTEM FREQ is set to 50 Hz
*
By pressing the AWB button, first the white
balance is adjusted automatically, then the black
balance is adjusted. Set the conditions for white
balance adjustment before proceeding.
• Only the black balance is adjusted when the
WHITE BAL switch is set to PRST.
41
Shooting techniques for different targets
Zebra pattern
Low angle recording
Recording can be controlled with the handle
START/STOP button during low angle recording
by moving the REC selector switch to the ON
position.
• To prevent erroneous operation when not using
the handle START/STOP button, set the REC
selector switch to the OFF position.
Press the ZEBRA button in the CAMERA mode
to show the zebra pattern on the viewfinder and
the LCD monitor so you can check the brightness
of the subject.
Parts that may be whited out through over
exposure are shown as a zebra pattern.
• Very bright
Handle START/
STOP button
• Reflecting parts
You can remove most overexposed parts by
adjusting the iris and shutter speed in the manual
mode to remove the areas with zebra patterns.
The display changes as follows each time you
REC selector switch
press the ZEBRA button: OFF
ZEBRA1
ZEBRAꢀ
OFF …
BARS
SHUTTER
SPEED SEL
CH 1
SELECT CH 2
1
INPUT
2
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
ON
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
ZEBRA button
The zebra pattern you have set appears as a
percentage on the display for about ꢀ seconds.
• In the setup menus, DISPLAY SETUP screen,
ZEBRA DETECT1 and ZEBRA DETECTꢀ, set
the brightness for the zebra patterns. (Page 81)
4ꢀ
Using the USER buttons
Checking and displaying shooting
status
You can allocate one of three features to each of
the USER 1, ꢀ buttons.
For details, see the setup menus, SW MODE
screen, USER1 and USERꢀ. (Page 79)
• If you press a USER button to which one of the
functions has been allocated and then turn off
the power, the added effect to the image will not
be retained.
PUSH
Color bars
DISP/MODE CHK button
Press the BARS button in the CAMERA mode
to output a color bar screen to a television or
monitor so you can adjust them. Press the button
again to turn the feature off.
Pressing the DISP/MODE CHK button during
recording or while recording is paused will
remove all displays from the screen except
for the operation status, counter, and warning
display. Press the button again to return to the
normal display. (Page 74)
• While the color bar is displayed, a test tone of
1 kHz will be output from the headphone
*
terminal, the HD SDI terminals or the HDMI
terminal. There will be no speaker output.
• The normal display is resumed when the power
is turned on.
997 Hz when SYSTEM FREQ is set to 50 Hz
• The color bar can be recorded by pressing the
START/STOP button.
*
During recording or while recording is paused,
information such as recording functions setting
status and a list of functions allocated to the
USER buttons can be displayed by keeping the
DISP/MODE CHK button held down. Release the
button to return to the normal display.
• The BARS button does not work in the PB
mode.
• The color bar display is canceled when the
power is turned off.
Pressing the DISP/MODE CHK button while the
thumbnail screen is displayed in PB mode will
display the properties of the selected clip.
(Clips can be selected by moving the cursor with
the Operation lever.)
43
Shooting techniques for different targets (continued)
Wave form monitor function
Adjusting the volume while shooting
AUDIO MON/ADV buttons
An image wave form can be displayed on the
LCD monitor by pressing the WFM button while
in CAMERA mode.
The display changes as follows each time you
press the WFM button: OFF
VECTOR OFF…
WFM (wave form)
• Wave forms will not be displayed in the
viewfinder.
PUSH
• Wave forms cannot be recorded.
• While wave forms are displayed, use the
viewfinder as well since part of the recording
screen will be hidden by the wave forms.
• Wave forms are not displayed when the
adjustment using the 3D FINE function is
being performed (Page 45), the images from
both the left and right lenses are displayed
(MIX image: Page 38) or only the image from
the right lens is being displayed (R-IMAGE
image: Page 79).
If you are monitoring the sound through
headphones while shooting, you can adjust the
volume with the AUDIO MON/ADV buttons.
(To adjust the recording level: Page 49)
• Volume adjustments will be memorized if the
power is turned off by moving the POWER/
Mode selector switch to the OFF position.
Shot mark function
The marks attached to the thumbnails of clips
are called shot marks. On the thumbnail screen
monitor you can select only those clips with a
shot mark and display them or play them back.
During recording, when you press the USER
button to which the SHOT MARK function has
been allocated, MARK ON appears in the LCD
monitor or the viewfinder, and a shot mark is
set for the thumbnail of the clip being recorded.
If you press the button again, the shot mark is
released. You can also set or release the shot
marks by performing the thumbnail operations for
clips. (Page 59)
• To display the left-lens image when the MIX
or R-IMAGE image is on the screen, press
the WFM button.
However, note that you cannot set or release
shot marks during playback.
• INVALID appears when you cannot set or
release shot marks.
44
Focus (FOCUS): Tilt the Operation lever in
the directions. The focal length for the
right lens is increased by tilting it in the
direction, and is reduced by tilting it in the
direction.
3D FINE function
As the left and right lenses are linked, you
normally do not need to adjust them.
If you wish to perform fine adjustments between
the two lenses, the 3D FINE function allows you
to adjust the vertical position of the images, focus
and iris.
Iris (IRIS): Press the AUDIO MON/ADV
+/- buttons. The iris of the right lens is opened
by pressing the + button, and is closed by
pressing the – button.
MENU
EXEC
PUSH
ENTER
Press the EXEC button to confirm the
adjustments.
4
• When the adjustment screen of the 3D FINE
function is being displayed, only the MIX
button and the USER button with R-IMAGE
allocated operate. The other buttons are not
operative.
AUDIO MON/ADV
Perform zoom adjustment (Page 34),
focus adjustment (Page 36) or brightness
adjustment (Page 37).
1
• The fine adjustment value is cleared when
a zoom operation, focus adjustment, or
brightness adjustment using the IRIS/CONV.
dial is performed after the adjustment.
• The fine adjustment value is cleared when
the power of the unit is turned off.
Press the EXEC button.
The fine adjustment screen is displayed.
2
3
Adjust the vertical position of the images,
focus and iris finely.
Vertical position of the images
(VERTICAL): Tilt the Operation lever in the
directions. The image from the right lens
moves upwards by tilting it in the direction,
and downwards by tilting it in the direction.
• This product is preadjusted at the factory
1
to minimize vertical misalignment. The
*
specification for vertical misalignment is
1.ꢀ % or less.
1
It is indicated in percentage of vertical
*
misalignment between the images from
the left and right lenses at the center
of the screen according to the effective
height of the screen, when measured
under the following conditions: the zoom
position at the maximum wide-angle
(Z00), the convergence point in the
center (C50), and shooting a subject at a
distance of 4.3 m.
45
Adjusting the shutter speed
• Remember that the faster the shutter speed,
the lower the sensitivity.
SPEED SEL
buttons
SHUTTER button
• The current shutter speed appears on the
viewfinder and LCD monitor when you have
selected ON in OTHER DISPLAY in the
DISPLAY SETUP screen of the setup menus.
It is not displayed if you have set the shutter
speed to normal (OFF).
• With artificial lighting and especially fluorescent
lights and mercury-vapor lamps, the luminance
changes in synchronization with the power
line frequency. When this frequency is 50 Hz,
mutual interference will occur between the
camera-recorder’s vertical sync frequency
(approx. 60 Hz) and the lighting frequency (50
Hz). This means that the white balance may
change periodically.
BARS
SHUTTER
SPEED SEL
CH 1
SELECT CH 2
1
INPUT
2
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
ON
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
Press the SHUTTER button.
1
2
Each time you press the SHUTTER button,
the shutter speed switches between normal
(OFF) and the speed you selected with the
SPEED SEL buttons.
Before shooting in areas with artificial lighting
or adjusting the white balance, set the shutter
speed as follows.
When SYSTEM FREQ is set to 59.9 Hz
SHUTTER 1/60
Progressive
Shutter speed
50 Hz
1/100
OFF (1/50)
OFF (1/50)
60 Hz
OFF (1/60)
1/60
mode
OFF (60i)
30P
ꢀ4P
1/1ꢀ0
After you have pressed the SHUTTER
button, press SPEED SEL buttons to
select the shutter speed.
The shutter speed changes as follows each
time you press SPEED SEL + button (The
order is reversed for the SPEED SEL −
button.)
When SYSTEM FREQ is set to 50 Hz
Progressive
Shutter speed
50 Hz
OFF (1/50)
OFF (1/50)
60 Hz
1/60
1/60
mode
OFF (50i)
ꢀ5P
When SYSTEM FREQ is set to 59.9 Hz
With the 1080/60i or 720/60P format
Standard (OFF)
1/60
1/250
1/100
1/120
SYNCRO SCAN
1/60
1/30
1/24
With the 1080/30P format
Standard (OFF)
1/50
1/120
1/250
1/50
SYNCRO SCAN
1/60
With the 1080/24P format
Standard (OFF)
1/50
1/50
1/60
1/120
1/250
SYNCRO SCAN
46
When SYSTEM FREQ is set to 50 Hz
With the 1080/50i or 720/50P format
Standard (OFF)
1/50
1/120
1/250
1/50
SYNCRO SCAN
1/60
With the 1080/25P format
Standard (OFF)
1/50
1/120
1/250
1/50
SYNCRO SCAN
1/25
1/60
Synchro scan
Set the shutter speed of the synchro scan (used
when shooting a television or computer monitor)
in the setup menus, CAMERA SETUP screen,
SYNCRO SCAN. (Page 78)
• Adjust the shutter speed to match the
frequency of the television or computer monitor
to minimize the horizontal noise that appears
when shooting such subjects.
• If the SYNCRO SCAN item is displayed in grey,
it cannot be used with the current recording
format. This function will only operate for preset
values for each recording format.
• You can change the progressive mode in the
setup menu with REC FORMAT item on the
RECORDING SETUP screen. (Page 80)
47
Switching Audio Input
During shooting, you can record up to two
channels of sound. You can also switch the input
sound to be recorded on each of the channels to
the built-in microphones, external microphones or
audio equipment connected to camera.
Using an external microphone and
audio equipment
Connect an external microphone or audio
1
equipment to the INPUT 1/2 (XLR 3-pin)
terminals. (Page 66)
CH1 SELECT switch CH2 SELECT switch
INPUT 1 terminal
INPUT 2 terminal
BARS
SHUTTER
SPEED SEL
CH 1
SELECT CH 2
1
INPUT
2
1
2
3
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
ON
HANDLE ZOOM
OFF
ON
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
Use the INPUT 1/2 switches to switch the
audio input.
2
INPUT 1/2 (MIC POWER +48V) switches
INPUT 1 switch INPUT 2 switch
Using the built-in microphone
Switch the CH1 SELECT switch to INT (L).
• Audio from the built-in microphone Lch is
recorded to audio channel 1.
1
Switch the CH2 SELECT switch to INT (R).
• Audio from the built-in microphone Rch is
recorded to audio channel ꢀ.
2
PUSH
LINE: (audio equipment is connected)
Input level is 0 dBu.
MIC: (an external microphone is
connected)
Input level is –50 dBu.
You can change the input level to –60 dBu
in the setup menus, RECORDING SETUP
screen MIC GAIN1 and MIC GAINꢀ. (Page
80)
Be aware that sensitivity will be higher if
you choose –60 dBu so you will record
more noise.
48
Adjusting the recording level
When using the phantom microphone
(which requires + 48 V power supply),
set the INPUT 1/ꢀ (MIC POWER +48V)
switches to ON.
3
ON: (When using the phantom
microphone)
+48 V power supply to INPUT 1/ꢀ
terminals.
PUSH
OFF: (When a phantom microphone is not
connected)
No power supply for INPUT 1/ꢀ terminals.
AUDIO LEVEL control knobs
Use the AUDIO LEVEL control knobs to adjust
the recording level of the built-in microphone
or of audio signals input through the INPUT 1/ꢀ
(XLR 3-pin) terminals.
(To adjust the volume of the sound for monitoring:
Page 44)
To adjust the recording level of the audio signals,
turn the AUDIO LEVEL control knobs while
referring to the audio level meter at the bottom
left of the viewfinder and LCD monitor.
• The battery will discharge faster if you use a
phantom microphone.
• Set to OFF if you connect equipment not
compatible with +48 V. You can damage such
equipment if you leave the setting at ON.
• When using the AG-MCꢀ00G (optional), set the
MIC GAIN item to –50 dBu.
Use the CH1 SELECT switch to select the
input signal to be recorded to audio channel
1.
4
-12dB
0dB
C 1
H
CH 2
INT (L):
Audio from the built-in microphone Lch is
recorded to audio channel 1.
INPUT 1:
• Check the recording volume level prior to
shooting.
Audio from a device connected to INPUT 1
terminal is recorded to channel 1.
INPUT 2:
Audio from a device connected to INPUT ꢀ
terminal is recorded to channel 1.
• The recording level of this camera is set
approximately 8 dB higher than Panasonic
broadcasting camera recorders (AJ series
products).
Use the CH2 SELECT switch to select the
input signal to be recorded to audio channel
2.
5
INT (R):
Audio from the built-in microphone Rch is
recorded to audio channel ꢀ.
INPUT 2:
Audio from a device connected to INPUT ꢀ
terminal is recorded to channel ꢀ.
• When inputting the microphone signal to
channels 1 and ꢀ, connect the microphone to
INPUT ꢀ and switch both CH1 SELECT and
CHꢀ SELECT to INPUT ꢀ.
49
Clip metadata
You can add the video and audio systems, name
of the videographer, shooting location, text
memos and other information to the video data
you have recorded on the SD Memory Cards.
This data is called the clip metadata.
videographer) and the PLACE NAME (name of
location).
4
LOCATION:
*
This indicates ALTITUDE, LONGITUDE,
LATITUDE, and SOURCE (altitude, longitude,
latitude, information source).
(Display method: Page 63)
2
SCENARIO:
*
There are two kinds of clip metadata: the data
that is recorded automatically during shooting,
and the data in the metadata upload file created
on the SD Memory Card which is loaded in the
unit.
This indicates the PROGRAM NAME, SCENE
NO. and TAKE NO.
NEWS 1:
This indicates the REPORTER (name of the
reporter) and PURPOSE (purpose of data
collection).
(Loading method: Page 51)
• Metadata can be produced with AVCCAM
Viewer. (Page 91)
When producing metadata using AVCCAM
Viewer, be sure to format SD Memory Cards
with this product and record the metadata on
the left-channel SD Memory Card.
NEWS 2:
This indicates the OBJECT (target of data
collection).
3
MEMO:
*
This indicates the PERSON (name of the
person who recorded the text memo) and
TEXT (contents of memo).
1 If there is no information in the metadata
What the clip metadata consists of
*
upload file, consecutive five-digit numbers will
be applied to the clips in the order that they
were recorded, with the first clip to be recorded
being given the number 0. The USER CLIP
NAME recording method is selectable. (Page
51)
2 When SCENARIO is to be input, you must
input the PROGRAM NAME. You cannot input
the SCENE NO. and TAKE NO. only.
You can set the items underlined below
by loading the metadata upload file on the
SD Memory Card. All other items are set
automatically during shooting.
GLOBAL CLIP ID:
This indicates the global clip ID that shows the
shooting status of the clip.
*
USER CLIP NAME:
This indicates the name of the clip that the
3 When MEMO is to be input, you must input
TEXT. You cannot input PERSON only.
*
1
user has set.
*
4 This information is not recorded with this unit.
*
VIDEO & AUDIO:
This indicates the recorded image’s FRAME
• Only printable ASCII characters can be
displayed by this unit.
RATE, RESOLUTION, PULL DOWN 4 system
*
and AUDIO.
• Due to the limitations imposed by this unit
on the number of characters which can be
displayed, not all the data can be displayed.
(This does not mean that the data which is
not displayed has been deleted.) Use an
AVCCAM viewer or other program to check
all the data.
ACCESS:
This indicates the CREATOR (name of
the person recording), CREATION DATE
(recording date), LAST UPDATE DATE (date
on which the data was last updated) and
LAST UPDATE PERSON (the person who last
updated the data).
DEVICE:
This indicates the MANUFACTURER
(manufacturer of the equipment), SERIAL NO.
(serial number of the equipment) and MODEL
NAME (equipment model name: AG-3DA1).
SHOOT:
This indicates the SHOOTER (name of the
50
CARD READ:
Read metadata set to the SD Memory Card
with the camera.
Uploading the metadata (META
DATA)
Move to LOAD, push the Operation lever,
select whether or not to read the metadata
(YES/NO), and push the Operation lever
again.
You can perform any of the following operations.
If necessary, make preparations prior to
undertaking the operations.
� Up to 10 items of metadata on the SD
Memory Card can be displayed, starting
from the most recent date of production.
� If characters other than single-byte
alphanumeric characters are used in the
metadata file name to be loaded, they
Loading the metadata
• Load the metadata recorded on the left-channel
SD Memory Card. (For details on contents of
the metadata, see the previous page.)
Selecting whether to record the metadata on
the SD Memory Cards
are displayed as “ ”.
RECORD:
∗
Initializing the metadata inside the unit
Displaying the metadata inside the unit
Select this to set whether to record the
metadata to be loaded into the unit
simultaneously on the SD Memory Cards.
Select ON to record the metadata or OFF to
cancel the recording, and push the Operation
lever.
Press the mode button and select
CAMERA mode.
1
Press the MENU button.
• Menu operation (Page 75)
2
The factory setting for this mode is OFF.
USER CLIP NAME:
The USER CLIP NAME recording method
is selectable. (For details: Page 5ꢀ)
CLIP COUNT RESET:
Tilt the lever in the
META DATA, and push the Operation lever
(or tilt in the direction).
directions to select
3
CAM MENU
2/2
Reset the counter value to 1.
DISPLAY SETUP
CARD FUNCTIONS
META DATA
Select whether or not to reset (YES/NO),
and push the Operation lever.
META DATA PROP:
OTHER FUNCTIONS
Select this to display the metadata which
has been recorded in the unit.
META INITIAL SET:
Select this to initialize the metadata which
has been recorded in the unit.
Select YES to initialize the metadata or NO
to cancel the initialization, and push the
Operation lever.
Tilt the Operation lever in the
directions to select item, and push the
Operation lever.
4
META DATA
1/2
CARD READ
NO
Press the MENU button to release the
menu mode.
RECORD
OFF
5
USER CLIP NAME
CLIP COUNT RESET
META DATA PROP
TYPE1
NO
NO
51
Clip metadata (continued)
Selecting the USER CLIP NAME
recording method
Press the MENU button and select META DATA
→ USER CLIP NAME to select the recording
method. Two options are available: TYPE1 and
TYPEꢀ.
USER CLIP NAME to be recorded
TYPE1
TYPEꢀ
Uploaded
data +
If clip metadata has Uploaded
been read in
data
COUNT
value
*
If no clip metadata
has been read in
or if the setting
Sequential 5- Sequential 5-
digit number, digit number,
for recording clip
metadata has been recording
turned off
in order of
in order of
recording
The COUNT value is indicated as a four-digit
number. The COUNT value is incremented
each time a new clip is captured if clip
metadata has been read in and TYPEꢀ has
been selected as the recording method.
The COUNT value can be reset using the
following procedure.
*
Press the MENU button, select META DATA→
CLIP COUNT RESET→YES, and push the
Operation lever to reset the counter value to 1.
CLIP COUNT RESET
CARD READ
RECORD
USER CLIP NAME
CLIP COUNT RESET
META DATA PROP
YES
NO
5ꢀ
Using the Counter
You can display a counter that indicates how
much time has elapsed during shooting or
playback.
Press the COUNTER button.
1
Each time you press the button, the display
changes as follows. (Page 68)
0 : 00. 00 (CAMERA mode only)
Counter value
CLIP 0 : 00 . 00
Displayed when CLIP is selected in the
REC COUNTER item on the settings menu
DISPLAY SETUP screen.
Values are automatically reset when
recording is started, and counter values are
displayed for each individual clip.
TC 12 : 34 : 56 . 01
Time code value
If SYSTEM FREQ is set to 59.9 Hz, time
code frame digits are displayed in ꢀ4
frames when ꢀ4P is set, and in 30 frames
when any other format is set.
If SYSTEM FREQ is set to 50 Hz, time
code frame digits are displayed in ꢀ5
frames.
UB 12 34 56 78
User information
No display
Data is not displayed.
Resetting the counter
Press the RESET button while the counter is
displayed.
53
Charging the built-in battery/Setting the time code
Recharging the built-in battery
Specifying the time code
(TC PRESET)
The camera’s internal battery saves the date and
time.
Set TC PRESET so you can record a value of
your choice as the initial setting for the time code
to be used at the start of recording.
When LOW INTERNAL BATTERY (indicating that
the internal battery has no remaining charge) is
displayed even when the date and time are set,
it means that the charge of the internal battery is
depleted. Do the following to recharge it.
Reset the date and time when fully recharged.
Set the POWER/Mode selector switch to
ON.
1
Select the TC PRESET item on the settings
menu TC/UB SETUP screen.
2
Connect the AC adaptor. (Page 24)
• Leave the POWER/Mode selector switch
at OFF.
1
• Menu operation (Page 75)
TC/UB SETUP
TC MODE
TCG
DF
REC RUN
NO
Leave the camera like this for about 4
hours.
• The internal battery charges during this
time.
2
TC PRESET
UB PRESET
NO
• Check the time code and menu operations
after recharging.
Tilt the Operation lever in the direction
to move to YES, and push the Operation
lever.
If the date and time are not memorized after
recharging, the internal battery requires
changing. Please consult the place of purchase.
3
TC PRESET
Setting the time code
TC MODE
TCG
In the setup menus, TC/UB SETUP screen, set
the following time code related items. (Page 80)
• TC MODE
TC PRESET
UB PRESET
YES
NO
(Only when SYSTEM FREQ is set to 59.9 Hz)
• TCG
• TC PRESET
54
When the screen below appears, set the
time code value.
Tilt the Operation lever in the direction
to move to YES, and push the Operation
lever.
4
6
Tilt the Operation lever in the
and select time code value.
directions
TC PRESET
TC PRESET
TC
PRESET?
TC
0 0 h 0 0m 0 0 s 0 0 f
YES
NO
With this unit, the time code value is adjusted
in accordance with the format and frame rate.
For this reason, bear in mind that making a
change in the format or frame rate may result in
discontinuity from the last time code value of the
previous recording. (Only when SYSTEM FREQ
is set to 59.9 Hz)
Tilt in the direction to move to the next digit,
and tilt in the
value.
directions again to select
TC PRESET
Time code
Recording format
TC
1 0 h 0 0m 0 0 s 0 0 f
adjustment
Adjustable in
1080/ꢀ4P
4-frame increments
You can reset the time code to zero by
pressing RESET button.
BARS
SHUTTER
SPEED SEL
CH 1
SELECT CH 2
1
INPUT
2
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
ON
OFF
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
RESET button
Push the Operation lever when you have
finished setting the time code.
5
55
Charging the built-in battery/Setting the time code (continued)
Setting user information
Set the user information.
Tilt the Operation lever in the
and select user information characters.
• You can use numbers from 0 to 9 and
letters from A to F.
4
directions
Setting user information allows you to store 8-
digit information in the hexadecimal format.
User information is automatically saved in the
memory and retained after you turn off the power.
UB PRESET
Set the POWER/Mode selector switch to
ON.
1
UB
0 0 0 0 0 0 0 0
In the setup menus, TC/UB SETUP screen,
select UB PRESET.
2
• Menu operation (Page 75)
Tilt in the direction to move to the next digit,
TC/UB SETUP
and tilt in the
character.
directions again to select
TC MODE
TCG
DF
REC RUN
NO
TC PRESET
UB PRESET
UB PRESET
NO
UB
F 0 0 0 0 0 0 0
Tilt the Operation lever in the direction
to move to YES, and push the Operation
lever.
3
You can reset the user information to nothing
by pressing RESET button.
UB PRESET
TC MODE
TCG
BARS
SHUTTER
SPEED SEL
TC PRESET
UB PRESET
YES
NO
CH 1
SELECT CH 2
INT(L)
INPUT 1
INPUT 2
1
INPUT
ON
OFF
2
INT(R)
INPUT 2
MIC POWER +48V
AUDIO
COUNTER RESET
MIX
WFM
EVF DTL
ZEBRA
RESET button
Push the Operation lever when you have
finished setting the user information.
5
6
Tilt the Operation lever in the direction
to move to YES, and push the Operation
lever.
UB PRESET
UB
PRESET?
YES
NO
56
Basic playback operations
CAMERA
Turn the POWER/Mode selector switch to
ON.
While pressing the lock release button, turn
the switch to ON.
1
2
1
PB
POWER
ON
OFF
Press the POWER/Mode selector switch
downwards so the mode lamp (PB) turns
on.
The camera is now in the PB mode.
• Each time you press the button, the mode
changes as below.
Lock release
button
Mode lamp
2
(PB)
CAMERA
PB
POWER
ON
OFF
PB
CAMERA
Play a clip using the Operating lever.
• For details on plyaing back clips using
thumbnails, see page 58.
3
Play (
)
Push
Push to play the clip currently indicated by the cursor.
MENU
EXEC
PUSH
ENTER
AUDIO MON/ADV
Fast forward (
)
MENU
EXEC
Tilt during playback to scroll quickly through the clip.
Tilt while paused to move to the next clip.
PUSH
ENTER
Tilt
rightward
AUDIO MON/ADV
Rewind (
)
MENU
EXEC
Tilt during playback to scroll quickly backwards through the clip.
Tilt while paused to move to the beginning of the current clip
and then to the previous clip.
PUSH
ENTER
Tilt
leftward
AUDIO MON/ADV
Stop (
)
MENU
EXEC
PUSH
ENTER
AUDIO MON/ADV
Tilt downwards
Pause (
)
Tilt upwards
Tilt during playback to pause the clip.
Play (
Tilt again to return to normal playback.
MENU
EXEC
)
PUSH
ENTER
AUDIO MON/ADV
• Clips shot by another AVCCAM or AVCHD device cannot be played back with this unit. Clips
shot with this camera will not be played back if you record on an SD Memory Card using another
AVCCAM or AVCHD device or delete some clips from the SD Memory Card.
• During initiation of an operation, for example, starting playback or between play of multiple clips in
succession, video and audio are muted and a black screen appears. This is not a malfunction.
• You cannot view a 3D image during fast forward or rewind. In these modes, the image from the left
lens is displayed on both the left and right channels.
57
Thumbnail screen
Video data created in one shooting session is called a clip. When the PB mode has been established,
the clips will be displayed on the LCD monitor as thumbnails. (When there is a large number of clips, it
will take some time for them to be displayed on the screen.)
You can perform the following operations using the thumbnail screen.
• Play and delete clips
• Add or delete shot marks
Basic thumbnail screen operations
To select a thumbnail:
MENU
EXEC
Tilt the Operation lever in the
directions to select a
thumbnail (yellow frame moves).
PUSH
ENTER
To play back clips:
Select the thumbnail, and push the Operation lever.
AUDIO MON/ADV
1
2
3
0004
M
10
9
11
4
5
6
7
8
58
1
Thumbnail display status (Page 61)
The types of clips displayed as thumbnails
appear in this area.
Adding shot marks to clips
Adding shot marks ( M ) will make it easier to
find the clips you are looking for.
2
3
4
5
Card status display
Displays the status of SD Memory Card.
Tilt the Operation lever in the
directions to move the yellow frame to the
clip for which a shot mark is to be added.
1
Battery remaining display (Page 70)
Displays the remaining battery capacity.
Cursor (yellow frame)
Displayed on the currently selected thumbnail.
Press the USER button to which the shot
mark function has been allocated. (Page
79)
2
Recording mode display
Displays the recording mode of the clip
currently highlighted by the cursor.
To release a shot mark, repeat the above steps.
• It is possible to add shot marks to clips
recorded using this product only.
6
7
8
Recording format display
Displays the recording format of the currently
selected clip.
Duration display
Displays the duration of the currently selected
clip.
Time display (Page 61)
Displays the time code at the start of clip
recording/user information at the start of clip
recording/time of recording/date of recording/
date and time of recording–according to the
settings.
9
Clip number
Displayed in order of recording (up to ꢀ00
clips). Numbers of clips that cannot be played
back (e.g. clips of different recording formats)
are displayed in red.
10
: Clip protect display
Displayed on the protected clips.
11 Indicators
: Shot mark
M
This indicates that a clip has a shot mark.
(Right column)
: Resume playback display
Displayed on the clips on which the resume
playback setting has been applied.
59
Playback settings (PLAY SETUP)
Resume playback (RESUME PLAY)
Use this setting to play back from where the clip
had previously been paused.
Press the MENU button.
• Menu operation (Page 75)
1
Set the RESUME PLAY item on the PLAY
SETUP screen to ON.
2
Press the MENU button to return to the
thumbnail screen.
3
Select a clip for playback.
If playback has previously been paused,
4
the resume playback indicator
will be
displayed on the clip thumbnail, and the
remainder of the clip will be played next time
the clip is selected for playback.
• To turn the resume playback setting off,
select OFF in step 2.
60
Thumbnail operations
Selecting the thumbnail display method (THUMBNAIL SETUP)
You can display the kind of clips you want to see
as thumbnails.
You can also set more precisely how you want
the thumbnails to appear on the screen.
INDICATOR:
Set whether or not to display the indicators
(ON/OFF). (Factory default setting is ON.)
Clip protect display and resume playback
display will still appear even if this setting is
set to OFF.
Press the MENU button.
• Menu operation (Page 75)
1
DATA DISPLAY:
Select the format of clip time display – time
code (TC)/user information (UB)/recording
time (TIME)/recording date (DATE)/
recording date and time (DATE & TIME).
DATE FORMAT:
Select the THUMBNAIL SETUP screen, and
push the Operation lever (or tilt in the
direction).
2
THUMBNAIL SETUP
Select the display order for recording date
- year-month-date (Y-M-D)/month-date-year
(M-D-Y)/date-month-year (D-M-Y).
This setting will not be reflected in CLIP
PROPERTY.
THUMBNAIL MODE
INDICATOR
ALL
ON
TC
DATA DISPLAY
DATE FORMAT
・
・
M
D
Y
Press the MENU button to return to the
thumbnail screen.
4
Tilt the Operation lever in the
3
directions to select item, and push the
Operation lever.
THUMBNAIL MODE
THUMBNAIL MODE
INDICATOR
ALL
SAME FORMAT
MARKER
DATADISPLAY
DATE FORMAT
THUMBNAIL MODE:
Select the clips to be displayed.
ALL:
Display all clips.
SAME FORMAT:
Display all clips of the same format
as the current recording format for
CAMERA mode.
MARKER:
Display all clips with shot marks.
61
Thumbnail operations (continued)
Deleting and protecting clips (OPERATION)
Clips may be deleted or protected.
• Protected clips cannot be deleted.
• If selecting ALL CLIPS to delete all clips from
the memory, this operation may take some
time to complete, depending on the volume
of clips to be deleted.
Press the MENU button.
• Menu operation (Page 75)
1
Select the OPERATION screen, and
push the Operation lever (or tilt in the
direction).
2
CLIP PROTECT:
PB MENU
YES:
PLAY SETUP
Select clips and push the Operation
lever to protect the selected clips.
THUMBNAIL SETUP
OPERATION
(
mark will be displayed.)
AV OUT SETUP
CARD FUNCTIONS
• Cancel protection when the protected
clip is selected.
(
mark will disappear.)
Executing a format of the memory card
will delete all clips even if they are
protected.
Tilt the Operation lever in the
directions to select item, and push the
Operation lever.
3
NO:
Return to the previous screen.
OPERATION
DELETE
NO
NO
Press the MENU button to return to the
thumbnail screen.
4
CLIP PROTECT
DELETE:
ALL CLIPS:
Delete all clips.
Select whether or not to delete (YES/
NO), and push the Operation lever.
SELECT:
Delete selected clips.
Select clips with the Operation lever.
Selected clips will be outlined in orange.
(Repeat this operation to select multiple
clips.)
Press the EXEC button to confirm, tilt
the Operation lever in the
directions
to select whether or not to delete (YES/
NO), and push the Operation lever.
NO:
Return to the previous screen.
6ꢀ
Checking clip information (CARD FUNCTIONS)
Clip information can be checked.
Clip information screen
CLIP PROPERTY
Press the MENU button.
• Menu operation (Page 75)
1
1
2
Select CARD FUNCTIONS, and push the
Operation lever (or tilt in the direction).
2
M
3
PB MENU
PLAY SETUP
THUMBNAIL SETUP
OPERATION
4
AV OUT SETUP
CARD FUNCTIONS
1 Clip number
2 Thumbnail (Thumbnail screen: Page 58)
3 Clip information
Displays the indicators attached to the clip,
and various other information.
Select YES, and push the Operation lever.
Information of the selected clip is displayed
on CLIP PROPERTY. (Right column)
3
START TC:
Time code value at start of
recording
START UB:
User information value at
start of recording
• Tilt the Operation lever in the
directions to display information from
previous or subsequent clips.
DATE/TIME: Date of recording and time
at start of recording
TIME ZONE: Time zone
DURATION: Clip length
Press the MENU button to return to the
thumbnail screen.
4
FORMAT:
Recording format
4 Clip meta data
Push the Operation lever while the clip
information screen is displayed to display
more detailed information, including
video and audio formats, name of the
videographer, etc.
Tilt the Operation lever in the
directions to verify the desired information.
(For more information on clip metadata:
Page 50)
63
Useful playback functions
Fast forward/rewind
Next/previous clip
Tilt the Operation lever in the
or
(rewind)
(fast forward) direction during
playback.
Tilt the Operation lever in the direction
during playback to pause the clip.
1
1
A clip will play forwards or backwards at
approximately 5 times normal speed.
MENU
EXEC
PUSH
ENTER
MENU
EXEC
PUSH
ENTER
AUDIO MON/ADV
Operation lever
AUDIO MON/ADV
Tilt the Operation lever in the
(rewind)
2
Operation lever
or
(fast forward) direction during
playback.
For a higher speed forward or rewind (at
• The screen will return to the thumbnail
display when moving beyond the beginning
of the first clip or the end of the final clip.
approximately 15 times normal speed), tilt the
Operation lever in the
(fast forward) or
(rewind) direction again during fast forward or
rewind.
To return to normal playback, tilt the Operation
lever in the direction (play).
• The screen will return to the thumbnail display
after the playback of the last clip is completed
during fast forward playback.
• The screen will return to the thumbnail display
after the playback of the first clip is completed
during rewind playback.
• No audio will be played during fast forward or
rewind playback.
64
Frame-by-frame playback
Viewing images on a monitor or television
Tilt the Operation lever in the direction
during playback to pause the clip.
You can view the images on a monitor or
television if you connect the unit using HD
SDI cables (not included) or HDMI cable (not
included).
1
Press the AUDIO MON/ADV buttons.
2
MENU
EXEC
Connect the camera to the monitor or TV
set. (Page 67)
1
PUSH
ENTER
Start playback.
2
• To show the information that appears on
the viewfinder and the LCD monitor on
the monitor or television, select ON in the
OUTPUT OSD item on the setup menu
DISPLAY SETUP screen. (Page 81)
AUDIO MON/ADV
AUDIO MON/ADV +/– buttons
When the + button is pressed, the images are
advanced in the forward direction, and when the
- button is pressed, they are advanced in the
reverse direction at half-second intervals.
To return to normal playback, tilt the Operation
lever in the direction (play).
Checking the date and time
To show the date and time of shooting on the
viewfinder and the LCD monitor, select the item
to be displayed with the DATE/TIME item on the
setup menu DISPLAY SETUP screen. (Page 81)
TIME: To display the time
Adjust volume
DATE: To display the date
TIME & DATE: To display the time and date
OFF: No display
The volume of audio output from the internal
speaker and headphone jack can be adjusted
with the AUDIO MON/ADV buttons during
playback.
MENU
EXEC
PUSH
ENTER
AUDIO MON/ADV
AUDIO MON/ADV +/– buttons
65
Connecting external units
Headphones
3.5-mm stereo mini jack
• Sound is no longer heard from the speaker when the headphones (optional) are connected.
External microphone
Microphone holder
Microphone (optional)
Microphone
AG-MC200G
holder adapter
12 mm
INPUT1 or
INPUT2
6 mm
• When attaching an external microphone to the microphone shoe, use the supplied microphone holder
and microphone holder adapter.
• When attaching the microphone holder and the microphone holder adapter, be sure to tighten the
screws firmly even though you might hear a squeaking sound.
66
TV/Monitor
Only the output signals from the camera are shown.
Monitor
HD SDI
1(L)
HD SDI
HD SDI
1(L)
2(R)
2(R)
HD SDI cable
(optional)
TV
HDMI
HDMI cable
(optional)
HDMI
• The signals cannot be output simultaneously from both the HD SDI terminals and HDMI terminal.
• Connect the left (L) and right (R) connectors correctly. Reverse connection may cause eyestrain.
67
Screen displays
Regular displays
24
23
1
TC 00 : 00 : 00 : 00
20min
PAUSE
2
3
4
5
6
R-IMAGE
P3.2K
22
21
20
PH1080
60
0
dB
7
8
9
19
MARK ON
ALC
DEC 25 2010 9:56:04
3D 1.5-12m MF55
18
17
16
1/250
24P
C 1
H
CH 2
F2.0
C00
Z01
10
11
12
13
14
15
_
[ + ]
[
]
25
VOLUME
1
Time code display
3
Media information display
Displays basic information about inserted SD
Memory Cards.
: Recording possible with both right and
left cards
Each time you press the COUNTER button,
the display switches over to the following data
(or no indication).
COUNTER:
Counter value
:
Right and/or left card is write-protected
CLIP:
: Recording not possible with right and/or
left card
CLIP counter value for respective clip
Displayed when the REC COUNTER item
on the settings menu DISPLAY SETUP
screen is set to CLIP.
� During playback, the time code display
is automatically set to CLIP, and the time
code is counted from a value of 0:00:00
for each clip.
: Right and/or left card is full
� Recording may be possible in some
cases even when this icon is displayed.
� Depending on the memory size and type
of SD Memory Card used, the icon may
not be displayed even when the card’s
memory becomes full during shooting
and shooting is stopped.
TC:
Time code value
: Playback-only
When the time code value could not be
read correctly from the SD Memory Card,
[TC∗] is displayed.
SD Memory Cards already containing ꢀ00
or more clips may be used for playback
only.
UB:
: Accessing card
User information
: No card inserted
When user information could not be read
correctly from the SD Memory Card, [UB∗]
is displayed.
4
5
Recording format display (Page 80)
System frequency display
60: 59.9 Hz 50: 50 Hz
2
Media capacity display
Displays a rough guide of the remaining
recording capacity of the card in use.
Not displayed during PB mode.
68
6
Information display
15 Convergence display
The following information is displayed
depending on the situation.
• Warning (Page 71)
• Performance of the auto white balance or
the auto black balance
The distance of the reference plane for a 3D
image is displayed with C00 to C99.
The higher the number is, the greater the
distance is.
• Use this as a rough guide.
• Switch position
16 Zoom position display
The zoom position is displayed with Z00
(maximum wide-angle) - Z99 (maximum
zoom).
7
8
Shutter speed display
The shutter speed is displayed here.
Microphone level automatic control
display
17 Focus control information display
Displays the focus control information with
95 - 00.
Appears when the MIC ALC item on the setup
menu RECORDING SETUP screen is set to
ON.
In the manual focus mode, MF appears. MF
is not displayed when the PUSH AUTO button
is pressed and the auto focus mode is set,
When the display is set to macro control,
the black and white of MF are displayed in
reverse.
9
Frame rate display
Displays recording frame rate.
• When SYSTEM FREQ is set to 59.9 Hz,
1080/60i is not displayed.
• When SYSTEM FREQ is set to 50 Hz,
1080/50i is not displayed.
95 (Focal distance: infinity)
:
10 Audio level meter display (Page 49)
Displayed when the LEVEL METER item on
the setup menu DISPLAY SETUP screen is
set to ON.
00 (Focal distance: approx. 5 cm)
Depending on the zoom position, the macro
range may not be enabled.
Also, depending on the zoom position, the
lower limit value of the macro range may be
different.
11 Focus bar display
Displayed when the FOCUS BAR button is
pressed.
18 Date and time display
12 Safety zone
Month:
The range of the zone is displayed when
the SAFETY ZONE item on the setup menu
DISPLAY SETUP screen is set to ON. (Page
81)
This indicates the range (90 %) within which
signals can be displayed by an ordinary
home-use TV set.
JAN (January), FEB (February),
MAR (March), APR (April), MAY (May),
JUN (June), JUL (July), AUG (August),
SEP (September), OCT (October),
NOV (November), DEC (December)
Day of the month
Year:
2001 - 2039
13 3D guide display
Hours
Displays the shooting range of distance within
which the shot subject can be reproduced as
a comfortable 3D image.
Minutes
Seconds
• Use this as a rough guide.
mmm dd yyyy hh:mm:ss
14 Iris display
19 Shot mark recording display
(SHOT MARK)
Displays the F-value.
Displayed when a USER button to which the
SHOT MARK function has previously been
allocated is pressed during recording.
INVALID will be displayed if a shot mark
cannot be attached.
(Continued on the next page)
69
Screen displays (continued)
24 Operation status display
20 Gain display
REC:
PAUSE:
CHK:
:
:
(
Recording
Recording standby
Rec check
Displays the gain value of the image amplifier
configured.
21 White balance information display
Displays the information on white balance.
P3.2 K/P5.6 K: Preset value
Playback
Playback paused
):Frame-by-frame playback
(Frame-by-frame reverse
playback)
): Skip (reverse skip)
): Fast forward/fast playback
(Rewind/fast reverse playback)
):
High-speed forward (high-speed
rewind)
Paused in final scene (paused in
initial scene)
Ach/Bch: Value set to position A or B of
WHITE BAL switch
22 Screen mode display
(
(
Displays the current screen mode.
It is cancelled when the display status is
changed, for example, when a menu is
changed or REC CHECK is performed.
R-IMAGE: The image from the right lens is
displayed.
(
(
):
MIX: The images from the left and right
lenses are superimposed and displayed.
25 Monitor audio level meter
When you press the AUDIO MON/ADV
button, the sound volume output from the
built-in speaker and headphone jack is
displayed.
23 Remaining battery capacity display
The battery display will change
→
→
→
as battery
capacity decreases.
will be displayed
in red when the battery is empty.
•
Remaining battery capacity may not be
displayed correctly with use at high or low
temperatures, or when the battery has
not been used for a long period of time.
To ensure that remaining battery capacity
is displayed correctly, use the battery
completely from a fully-charged state,
and charge the battery again. (Remaining
battery capacity may still not be displayed
correctly if the battery has been used for
long periods at high or low temperatures,
or if the battery has been recharged a large
number of times.)
• The remaining battery capacity display is
a guideline and may change according to
usage conditions.
70
Main warning displays
The main warning displays appearing on the LCD monitor or viewfinder are listed below. If a warning
display is not listed, check carefully the message displayed.
■C
CANNOT RECORD
CANNOT BE USED DUE TO
VIDEO IMAGES ARE PROTECTED.
INCOMPATIBLE DATA.
REMOVE PROTECTION?
No use is possible because the standard for
YES NO
the data is different.
Recording is not possible, as the video images
If the system frequency has been changed,
in the card are protected. Do you wish to
format the SD Memory Cards with current
remove the protection?
SYSTEM FREQ setting.
Yes/No
CANNOT DELETE.
CANNOT RECORD — INCOMPATIBLE
Clip cannot be deleted.
CONTROL DATA.
Recording is not possible, as the unit does not
CANNOT DELETE WITH THIS BUTTON
Clip cannot be deleted.
support this control data.
CANNOT RECORD 3D CLIP INTO THIS
CARD
3D clips cannot be recorded with this card.
CANNOT HANDLE. THE NUMBER OF
CLIPS HAS EXCEEDED THE MAXIMUM
LIMIT.
The maximum number of clips has been
reached and no further operation is possible.
CANNOT RECORD 3D CLIP THIS CARD.
PLEASE CHANGE THE CARD.
3D clips cannot be recorded with this card. Use
cards of class 4 or above.
CANNOT OPERATE. FAN MOTOR IS STOP.
PLEASE TURN OFF.
The unit cannot operate, as the fan motor has
stopped. Turn off the power.
CANNOT SELECT MORE CLIPS.
Additional clips cannot be selected.
CANNOT OPERATE. TEMPERATURE IS
HIGH. PLEASE TURN OFF AND WAIT A
WHILE.
The unit cannot operate, as the temperature is
too high. Turn off the power and wait a while.
CANNOT SET.
The operation you intended is not possible
now.
CARD DOOR OPENED.
The SD Memory Card slot cover is open.
CANNOT PLAY.
No playback is possible.
CARD ERROR.
PLEASE REFORMAT.
Formatting has failed. The card needs to be
reformatted.
CANNOT PLAY WITH THIS BUTTON
No playback is possible.
CANNOT PROTECT.
Clip protection is not possible.
CARD FULL.
The card is full.
CANNOT RECORD.
THE NUMBER OF CLIPS HAS EXCEEDED
THE MAXIMUM LIMIT.
The maximum number of clips has been
reached and no further clips can be recorded.
(Continued on the next page)
71
Screen displays (continued)
■L
CHECK CARD.
LOW BATTERY
The remaining battery power is low.
Please check the card.
If you use an SD Memory Card that has been
used with other devices or personal computers,
for the first time with this unit, CHECK CARD
may be displayed and the unit cannot operate.
In this case, perform the following:
LOW INTERNAL BATTERY
The remaining power of the internal battery is
low.
■N
NO CARD
A Remove the SD Memory Card from the unit
and reinsert it. (Page 30)
No card is inserted.
The CHECK CARD display may disappear if
the unit detects the card.
NO DATA
There are no clips in the card.
B If CHECK CARD remains displayed even
if you remove and insert the card several
times, check the contents of the card
and delete all its data, using a personal
computer.
NOW ACCESSING.
PLEASE DO NOT REMOVE CARD.
Card is currently being accessed. Please do
not remove the card.
C Format the card with this unit. (Page 30)
If the data in the card is unreadable or cannot
be deleted with a personal computer, the card
may be damaged. Use another SD Memory
Card.
■P
PLAYBACK ONLY
The card is for playback only.
CLIP NUMBER IS FULL
No more clips can be recorded with this card.
■R
REC STOPPED BY REC SIZE LIMIT.
PLEASE PUSH REC BUTTON AGAIN TO
RESTART.
Recording has stopped, as the maximum file
size that can be recorded has been exceeded.
If you wish to continue recording, press the
START/STOP button.
CONTROL DATA ERROR HAS BEEN
DETECTED.
An error has been detected in the control
information.
■I
INCOMPATIBLE DATA
Data are incompatible with this unit.
■S
If INCOMPATIBLE DATA is displayed and the
unit cannot operate, perform the following:
SD CARD FORMAT?
YES NO
Do you wish to format the SD Memory Card
A Remove the SD Memory Card from the unit.
B Check the contents of the card and delete
all its data, using a personal computer.
now?
Yes/No
C Format the card with this unit. (Page 30)
SET DATE AND TIME
Set the date and time.
If the data in the card is unreadable or cannot
be deleted with a personal computer, the card
may be damaged. Use another SD Memory
Card.
■T
THE CLIP IS PROTECTED.
PLEASE CANCEL PROTECTION.
The clip is protected. Please cancel the
protection.
INCOMPATIBLE CARD.
PLEASE CHECK CARD.
Recording may not be successful with this
card. Please check the card.
7ꢀ
Main error displays
THE TC MODE IS CHANGED TO "NDF"
NDF is selected as the TC MODE setting.
(Only when SYSTEM FREQ is set to 59.9 Hz)
The following messages are displayed when
an error has occurred in the camera or the SD
Memory Card. If the problem is not solved by
switching the power off and back on again,
either change the card in accordance with the
instructions displayed, or consult the place of
purchase.
THIS CARD CANNOT RECORD IN VIDEO
MODE.
The card cannot be used for video recording.
THUMBNAIL DATA ERROR IS DETECTED.
An error has been detected in the thumbnail
information.
■C
CANNOT RECORD
TURN POWER OFF
Displayed when an error has occurred during
recording.
Turn the power off.
■U
■N
UNABLE TO FORMAT.
The card cannot be formatted.
NG
Displayed when an error has occurred with the
camera itself. Start the recording again.
FOCUS NG (error with focus operation)
ZOOM NG (error with zoom operation)
USER CLIP NAME MODIFIED
The user clip name you entered has been
modified.
■W
WRITE PROTECT
■R
REC WARNING
The card is write-protected.
Displayed when an error has occurred during
recording. Start the recording again. If the
message appears again, please consult the
place of purchase.
• Please switch the power off if the message
continues to appear.
• Please try inserting a different card if the
message appears again after restarting
recording.
■S
SYSTEM ERROR
TURN POWER OFF
Displayed when an error has occurred in the
system. Switch the power off and back on
again.
•
If this error is displayed when accessing
the SD Memory Card, such as when
deleting a clip, the SD Memory Card may
be damaged. Please replace it with a new
SD Memory Card.
73
Screen displays (continued)
Setting the DISPLAY items
Display the following items on the viewfinder and LCD monitor by pressing the DISP/MODE CHK
button or by configuring OTHER DISPLAY of the DISPLAY SETUP screen of the setup menus. (Page
8ꢀ)
MODE CHK
OTHER DISPLAY settings
Displays
(Hold down DISP/
MODE CHK button)
DISPLAY
ON
OFF
1
ꢀ
3
4
5
6
7
8
Time code display
—
—
—
—
—
—
—
x
Media capacity display
Media information display
Recording format display
System frequency display
Information display
x
—
—
—
x
Shutter speed display
Microphone level automatic control
display
x
9
Frame rate display
x
10 Audio level meter display
11 Focus bar display
—
—
—
—
—
—
—
—
x
1ꢀ Safety zone
—
—
—
13 3D guide display
14 Iris display
15 Convergence display
16 Zoom position display
17 Focus control information display
18 Date and time display
19 Shot mark recording display
ꢀ0 Gain display
—
—
—
—
—
—
—
—
—
—
x
—
—
ꢀ1 White balance information display
ꢀꢀ Screen mode display
ꢀ3 Remaining battery capacity display
ꢀ4 Operation status display
ꢀ5 Monitor audio level meter
x
—
—
—
—
—
—
—
—
—
—
—
—
:
Displayed
x: Not displayed
—: Displayed depending on other settings
The item in in the MODE CHK space appears when you press and hold the DISP/MODE CHK
button.
The item in in the DISPLAY space disappears when you press the DISP/MODE CHK button.
74
Using the setup menus
Use the setup menus to change the settings to
suit the scenes you are shooting or what you are
recording.
Tilt the Operation lever in the
directions to move the yellow cursor to the
function you wish to set.
Example:
2
MENU button
CAM MENU
1/2
MENU
EXEC
CAMERA SETUP
SW MODE
PUSH
ENTER
RECORDING SETUP
TC/UB SETUP
Operation
lever
AUDIO MON/ADV
AV OUT SETUP
Push the Operation lever (or tilt in the
direction) to display the setting items.
Example:
3
4
PUSH
SW MODE
HANDLE ZOOM
IRIS DIAL
USER1
L/OFF/H
DOWN OPEN
SHOT MARK
Using the menus
・
USER2
R
IMAGE
• The menu items indicated in the gray
characters cannot be changed its settings.
• Only the CARD FUNCTIONS screen can be
changed when the left and right SD Memory
Cards are inserted in reverse order or
Tilt the Operation lever in the
directions to move the yellow cursor to the
item you wish to set.
unformatted SD Memory cards are inserted.
Example:
SW MODE
When the unit is in other than playback or
1
HANDLE ZOOM
IRIS DIAL
USER1
L/OFF/H
recording mode, press the MENU button.
The following is displayed on the viewfinder
and LCD monitor.
DOWN OPEN
SHOT MARK
・
USER2
R
IMAGE
CAMERA mode (Example)
CAM MENU
1/2
CAMERA SETUP
SW MODE
RECORDING SETUP
TC/UB SETUP
Push the Operation lever (or tilt in the
direction) to set the item.
To change values or other parameters, tilt the
5
AV OUT SETUP
Operation lever in the
directions.
Example:
PB mode (Example)
IRIS DIAL
HANDLE ZOOM
IRIS DIAL
USER1
PB MENU
DOWN OPEN
UP OPEN
PLAY SETUP
THUMBNAIL SETUP
OPERATION
USER2
AV OUT SETUP
CARD FUNCTIONS
• Tilt the Operation lever in the direction to
return to the previous menu.
(Continued on the next page)
75
Using the setup menus (continued)
Repeat steps 4 - 5 to change any other
items.
6
Press the MENU button to complete settings
and return to the normal screen.
Repeat steps 2 - 5 to change any other
settings.
7
Press the MENU button to complete settings
and return to the normal screen.
Initializing the menu settings
You can initialize the menu settings to their
factory default ones by selecting YES for the
MENU INIT item on the OTHER FUNCTIONS
screen. (Page 83)
• The TIME ZONE setting will not return to the
factory setting.
76
Setup menu structure
Camera mode menu
CAM MENU
CAMERA SETUP
(Page 78)
SYNCRO SCAN
DETAIL LEVEL
V DETAIL LEVEL
DETAIL CORING
CHROMA LEVEL
CHROMA PHASE
COLOR TEMP Ach
COLOR TEMP Bch
MASTER PED
GAMMA
SW MODE
(Page 79)
HANDLE ZOOM
IRIS DIAL
USER1
USERꢀ
KNEE
MATRIX
RECORDING SETUP
(Page 80)
REC FORMAT
MIC ALC
MIC GAIN1
MIC GAINꢀ
TC/UB SETUP
(Page 80)
TC MODE
TCG
TC PRESET
UB PRESET
AV OUT SETUP
(Page 81)
SDI OUT
HP MODE
DISPLAY SETUP
(Page 81)
ZEBRA DETECT1
ZEBRA DETECTꢀ
SAFETY ZONE
REC COUNTER
OUTPUT OSD
CARD FUNCTIONS
(Page 8ꢀ)
CARD FORMAT
DATE/TIME
META DATA
(Page 8ꢀ)
CARD READ
RECORD
USER CLIP NAME
CLIP COUNT RESET
META DATA PROP
META INITIAL SET
LEVEL METER
ZOOM & FOCUS
COVERGENCE
CARD & BATTERY
OTHER DISPLAY
LCD/EVF BACKLIGHT
OTHER FUNCTIONS
(Page 83)
REC LAMP
CLOCK SET
TIME ZONE
SYSTEM FREQ
SYSTEM INFO
MENU INIT
OPERATION
UPDATE
LOG DATA
Playback mode menu
PB MENU
PLAY SETUP
(Page 84)
RESUME PLAY
THUMBNAIL SETUP
(Page 84)
THUMBNAIL MODE
INDICATOR
DATA DISPLAY
DATE FORMAT
OPERATION
(Page 84)
DELETE
CLIP PROTECT
AV OUT SETUP
(Page 81)
SDI OUT
CARD FUNCTIONS
(Page 8ꢀ)
CLIP PROPERTY
77
Setup menu list
CAMERA SETUP screen
Display
mode
Item
Description of settings
SYNCRO
SCAN
(Camera) Adjusts the synchro scan shutter speed used for shooting images on a TV
screen, etc.
Holding the Operation lever toward the or direction will cause the values
to change at a faster rate.
Available shutter speeds with SYSTEM Available shutter speeds with
FREQ 59.9 Hz
• 60P/60i:
SYSTEM FREQ 50 Hz
• 50P/50i:
1/60.0…1/ꢀ50.0
• 30P:
1/50.0 … 1/ꢀ50.0
• 25P:
1/30.0…1/48.0…1/ꢀ50.0
• 24P:
1/ꢀ5.0 … 1/48.0 … 1/ꢀ50.0
1/ꢀ4.0…1/48.0…1/ꢀ50.0
DETAIL LEVEL (Camera) Adjusts the level of the image outline correction (in the horizontal and vertical
directions).
- 7…0…+ 7
V DETAIL
LEVEL
(Camera) Adjusts the level of outline correction in the vertical direction.
- 7…0…+ 7
DETAIL
CORING
(Camera) Adjusts the level of noise reduction of the detail signal.
- 7…0…+ 7
Set to – for a clearer image. Noise increases slightly.
Set to + to reduce noise.
CHROMA
LEVEL
(Camera) Adjusts the chroma level.
- 7…0…+ 7
CHROMA
PHASE
(Camera) Makes fine adjustments to the chroma phase.
- 7…0…+ 7
COLOR TEMP (Camera) Makes fine adjustments to the color temperature (after white balance Ach
Ach
adjustment).
- 7…0…+ 7
COLOR TEMP (Camera) Makes fine adjustments to the color temperature (after white balance Bch
Bch
adjustment).
- 7…0…+ 7
MASTER PED
(Camera) Adjusts the master pedestal (black level of the image) as the basis for
images.
- 15…0…+ 15
GAMMA
(Camera) Selects the gamma curves.
HD NORM: This gamma setting is suitable for HD shooting.
LOW:
Makes a mellow image using the gamma curve which has a
gentle incline in low-brightness curve. The contrast sharpens.
Expands the tone of dark parts and makes a brighter image using
the gamma curve which has a sharp incline in low-brightness
curve. The contrast softens.
HIGH:
B.PRESS: Makes the contrast shaper than LOW.
CINE-LIKE D: Uses a gamma designed to create cinema-like images.
CINE-LIKE V: Uses a gamma designed to create cinema-like images with
emphasized contrast.
• When you select CINE-LIKE gamma, we recommend setting the lens
aperture lower than normal image level (approximately 1/ꢀ) for optimal
results.
indicates the factory setting.
78
CAMERA SETUP screen (continued)
Display
mode
Item
Description of settings
KNEE
(Camera) To avoid overexposure, select the compression level (knee point) of the high
intensity video signals received through MOS.
LOW: Low setting (Compression starts at approx. 80 %.)
MID:
Medium setting (Compression starts at approx. 90 %.)
HIGH: High Setting (Compression starts at approx. 100 %.)
• Not available when GAMMA is set to CINE-LIKE.
MATRIX
(Camera) Selects the MATRIX table suitable for the desired color expression during
shooting.
NORM1: Suitable for shooting in the open air or under a halogen lamp.
NORM2: Suitable for brighter colors than the NORM1 mode.
CINE-LIKE: Suitable for cinema-like image.
SW MODE screen
Display
mode
Item
Description of settings
HANDLE
ZOOM
(Camera) Sets the zoom speed assigned to each setting position of the HANDLE ZOOM
switch.
L/OFF/H: Sets LOW (low speed)/OFF/HIGH (high speed) to the 1/ꢀ/3 position.
(Zoom is disabled when set to OFF.)
L/M/H: Sets LOW (low speed)/MID (medium speed)/HIGH (high speed) to
the 1/ꢀ/3 position.
L/OFF/M:Sets LOW (low speed)/OFF/MID (medium speed) to the 1/ꢀ/3
position. (Zoom is disabled when set to OFF.)
IRIS DIAL
USER1
(Camera) Sets the rotation direction and the aperture control of the IRIS/CONV. dial.
DOWN OPEN:The iris opens when the IRIS/CONV. dial is turned downward.
UP OPEN: The iris opens when the IRIS/CONV. dial is turned upward.
• This setting does not change the direction of the convergence point
adjustment.
(Camera) Selects the function assigned to the USER1 button.
INH:
USER1 button is disabled. No function operates by pressing
the USER1 button.
R-IMAGE:
MIX:
The image from the right lens is displayed on the viewfinder
and LCD monitor.
The images from the left and right lenses are superimposed
and displayed on the viewfinder and LCD monitor. (Page 38)
SHOT MARK: Shot mark recording (Page 44)
USER2
(Camera) Assigns a function to the USERꢀ button.
The setting contents are the same as USER1.
INH
R-IMAGE
MIX
SHOT MARK
indicates the factory setting.
79
Setup menu list (continued)
RECORDING SETUP screen
Display
mode
Item
Description of settings
REC FORMAT
(Camera) Selects the recording format.
When SYSTEM FREQ is set to 59.9 Hz
PH 1080/60i
PH 1080/30P
PH 1080/24P
PH 720/60P
• PH 1080/ꢀ4P represents native recording.
When SYSTEM FREQ is set to 50 Hz
PH 1080/50i
PH 1080/25P
PH 720/50P
MIC ALC
(Camera) Sets mic level auto control to ON or OFF.
ON OFF
Set to ON to reduce distortion at high input levels.
To adjust the recording level of audio signals (not related to this setting), use
the AUDIO LEVEL knobs.
MIC GAIN1
MIC GAIN2
(Camera) Sets the input level of the external microphone connected to the INPUT 1
terminal. (Page 48)
-50dB -60dB
(Camera) Sets the input level of the external microphone connected to the INPUT ꢀ
terminal. (Page 48)
-50dB -60dB
TC/UB SETUP screen
Display
mode
Item
Description of settings
TC MODE
(Camera) Selects the correction mode of the internal time code generator when the time
code of the internal time code generator is recorded.
DF:
Uses the drop frame mode.
NDF:
Uses the non-drop frame mode.
• TC MODE is automatically set to NDF when you set recording frame rate of
recording format to ꢀ4P. (Only when SYSTEM FREQ is set to 59.9 Hz)
TCG
(Camera) Sets the mode in which you advance the internal time code generator.
FREE RUN: The time code is advanced regardless of the operation mode.
• A slight time error may occur when switching to PB mode if the frame rate is
set to ꢀ4P. (Only when SYSTEM FREQ is set to 59.9 Hz)
REC RUN: The time code is advanced only when recording.
TC PRESET
UB PRESET
(Camera) Sets the initial time code.
YES NO
• Set the frame value to 0 or a multiple of 4 when you set recording frame
rate of recording format to ꢀ4P. If any other value is set, the recorded time
code will mis-match. (Only when SYSTEM FREQ is set to 59.9 Hz)
(Camera) Sets the user information.
YES NO
indicates the factory setting.
80
AV OUT SETUP screen
Display
mode
Item
Description of settings
SDI OUT
(Camera) Sets whether to output the signal from the HD SDI terminal.
(PB)
ON: The signal is output from the HD SDI terminal. It is not output from the
HDMI terminal.
OFF: The signal is not output from the HD SDI terminal. It is output from the
HDMI terminal.
HP MODE
(Camera) Selects the sound heard through the headphones.
LIVE: The sound which has been input from the microphone is output
as is. This setting is selected when delays in the sound are
annoying.
RECORDING: The sound in the status which is to be recorded (the sound
synchronized with the images) is output.
DISPLAY SETUP screen
Display
mode
Item
Description of settings
ZEBRA
(Camera) Selects the brightness level of the left-leaning zebra patterns on the screen.
DETECT1
105%, 100%, 95%, 90%, 85%, 80%, 75%, 70%, 65%, 60%, 55%, 50%
ZEBRA
(Camera) Selects the brightness level of the right-leaning zebra patterns on the screen.
DETECT2
105%, 100%, 95%, 90%, 85%, 80%, 75%, 70%, 65%, 60%, 55%, 50%
SAFETY ZONE (Camera) Sets whether to display the safety zone. (Page 69)
ON OFF
REC
COUNTER
(Camera) Selects counter operation during recording.
TOTAL: The count continues to increase until the RESET button is pressed
to reset it.
CLIP: Resets the counter at start of recording and counts the time of each
recording session.
• In PB mode, operation is always in CLIP mode.
OUTPUT OSD (Camera) Select ON to output the information displayed on the screen together with the
video signals.
ON OFF
• Time code, audio lever meter, and focus bar displays are not output.
DATE/TIME
(Camera) Sets whether to display the date and time on the screen together with the
video signals.
TIME: The time is displayed.
DATE: The date is displayed.
TIME & DATE: The date and time are displayed.
OFF:
The date and time are not displayed.
LEVEL METER (Camera) Select ON to display the audio level meter.
ON OFF
ZOOM &
FOCUS
(Camera) Sets whether to display the zoom and focus values.
ON OFF
CONVERGENCE (Camera) Sets whether to display the position of the reference plane (relative value).
(Page 38)
ON OFF
indicates the factory setting.
81
Setup menu list (continued)
DISPLAY SETUP screen (continued)
Display
mode
Item
Description of settings
CARD &
(Camera) Select ON to display the remaining SD Memory Card recording capacity and
BATTERY
remaining battery charge.
ON OFF
OTHER
(Camera) Select how much information to display on the viewfinder and the LCD
DISPLAY
monitor. (Page 74)
ON OFF
LCD/EVF
(Camera) Adjusts the backlight of the LCD monitor and viewfinder. Select HIGH for
BACKLIGHT
brighter backlight.
LOW, NORMAL, HIGH
CARD FUNCTIONS screen
Display
mode
Item
Description of settings
CARD
(Camera) Formats the SD Memory Card.
FORMAT
YES:
NO:
Formats the card.
Returns to the last screen.
• Be sure to insert the two SD Memory Cards.
CLIP
(PB)
Displays information about the selected clip.
PROPERTY
YES:
NO:
Displays clip information.
Returns to the last screen.
META DATA screen
Display
mode
Item
Description of settings
CARD READ
(Camera) Loads the metadata recorded on the SD Memory Card into the unit.
YES NO
• Be sure to insert the two SD Memory Cards.
• “NO FILE” is displayed when no metadata is recorded in the SD Memory
Card.
RECORD
(Camera) Sets whether to record the metadata to be loaded into the unit simultaneously
on an SD Memory Card.
ON:
Records simultaneously.
OFF:
Does not record simultaneously.
USER CLIP
NAME
(Camera) Selects the method of USER CLIP NAME recording.
TYPE1: User clip name is the same as the CLIP NAME if there is no
uploaded metadata or data.
TYPE2: User clip name is the same as the CLIP NAME if no combination of
data and COUNT value is uploaded, or if there is no uploaded data.
CLIP COUNT
RESET
(Camera) Resets the COUNT value to 1.
YES NO
META DATA
PROP
(Camera) Displays the metadata which has been recorded in the unit.
YES NO
META INITIAL
SET
(Camera) Initializes the metadata which has been recorded in the unit. All the settings
including the ON or OFF setting for RECORD are now cleared.
YES NO
indicates the factory setting.
8ꢀ
OTHER FUNCTIONS screen
Display
mode
Item
Description of settings
REC LAMP
(Camera) Sets lighting of the tally lamp.
FRONT: Front tally lamp (microphone side) lights.
REAR: Rear tally lamp (viewfinder side) lights.
BOTH: Both tally lamps light.
OFF:
The tally lamp does not light.
CLOCK SET
TIME ZONE
(Camera) Sets the camera’s calendar.
YES NO
(Camera) Adds to or deducts from GMT the time value of -1ꢀ:00 to +13:00 in 30-minute
steps. (Refer to the table below.)
+00:00
Time
difference
Time
difference
Area
Area
+ 00:00
– 01:00
– 02:00
– 03:00
– 04:00
– 05:00
– 06:00
– 07:00
– 08:00
– 09:00
– 10:00
– 11:00
– 12:00
+ 13:00
+ 12:00
+ 11:00
+ 10:00
+ 09:00
+ 08:00
+ 07:00
+ 06:00
+ 05:00
+ 04:00
+ 03:00
+ 02:00
+ 01:00
Greenwich
Azores Islands
Mid-Atlantic
Buenos Aires
Halifax
New York
Chicago
Denver
Los Angeles
Alaska
Hawaii
Midway Island
Kwajalein
– 00:30
– 01:30
– 02:30
– 03:30
– 04:30
– 05:30
– 06:30
– 07:30
– 08:30
– 09:30
– 10:30
– 11:30
+ 12:30
+ 11:30
+ 10:30
+ 09:30
+ 08:30
+ 07:30
+ 06:30
+ 05:30
+ 04:30
+ 03:30
+ 02:30
+ 01:30
+ 00:30
Newfoundland Island
Marquesas Islands
Norfolk Island
Lord Howe Island
Darwin
New Zealand
Solomon Islands
Guam
Tokyo
Beijing
Yangon
Mumbai
Kabul
Bangkok
Dacca
Islamabad
Abu Dhabi
Moscow
Eastern Europe
Central Europe
Tehran
SYSTEM FREQ (Camera) This is used to switch the system frequency.
59.9Hz: NTSC mode (59.94 Hz)
50Hz: PAL mode
• When the system frequency has been changed, turn the unit’s power off
and then back on so that the setting takes effect.
SYSTEM INFO (Camera) Displays the version of the system in this camera.
YES NO
MENU INIT
(Camera) Returns the menu settings to the factory settings.
YES NO
• TIME ZONE setting will not return to the factory setting.
OPERATION
UPDATE
(Camera) Displays the power-on time of the unit (a 5-digit figure).
(Camera) Updates the system version of this unit.
YES: Enables updating.
NO: Updating is not performed.
• For detailed information on updating, visit the following website:
indicates the factory setting.
83
Setup menu list (continued)
OTHER FUNCTIONS screen (continued)
Display
mode
Item
Description of settings
LOG DATA
(Camera) Stores the product information of this unit in the SD Memory Card.
YES NO
PLAY SETUP screen
Display
mode
Item
Description of settings
RESUME PLAY (PB)
ON OFF
When set to ON, playback resumes from the video position at which clip
playback stopped.
THUMBNAIL SETUP screen
Display
mode
Item
Description of settings
Selects the thumbnail display method.
ALL: All the clips are displayed.
SAME FORMAT: The clips in the same recording format are displayed.
MARKER: The clips with shot marks are displayed.
Sets whether the indicator is to be displayed or not.
THUMBNAIL
MODE
(PB)
INDICATOR
(PB)
ON:
Displayed
OFF:
Not displayed
DATA DISPLAY (PB)
Selects the information displayed in the time display of clips.
TC:
UB:
Time code
User information
TIME: Shooting time
DATE: Shooting date
DATE & TIME: Shooting date and time
DATE FORMAT (PB)
Selects the order for displaying the recording date/time when DATE DISPLAY
is set to DATE.
Y-M-D: year/month/day
M-D-Y: month/day/year
D-M-Y: day/month/year
OPERATION screen
Display
mode
Item
Description of settings
DELETE
(PB)
Deletes clips.
ALL CLIPS: Deletes all clips.
SELECT:
Deletes only the selected clips. Press the EXEC button to
delete clips.
NO:
Returns to the last screen.
• Clips for which CLIP PROTECT is specified are not deleted.
CLIP PROTECT (PB)
Protects clips to prevent accidental deletion.
YES:
NO:
Enables clip protection or cancels protection.
Returns to the last screen.
• Executing a format of the memory card will delete all clips even if they are
protected. (Page 30)
indicates the factory setting.
84
Before calling for service
Power supply
There’s no power.
• Make sure the battery and AC adaptor are connected properly.
Check the connections again.
Page ꢀ4
Page ꢀ3
Power goes off as soon as
it is turned on.
• The battery may have run out.
If the remaining battery charge display
battery is exhausted.
turns red, the
Either recharge the battery or replace the discharged battery
with a fully charged one.
Battery
The battery runs down
quickly.
• Make sure the battery is fully charged.
Keep charging until the CHARGE lamp on the battery charger
goes out.
Page ꢀ3
• Are you using the battery in a cold place?
The battery is affected by the ambient temperature. Its
operating time is reduced in low-temperatures.
• The battery may have reached the end of its service life. The
battery will become unchargeable. The battery has a certain
service life which varies depending on how the battery is used.
If the battery operates only for a short period even when it is
charged adequately, it has reached the end of its service life.
The remaining battery
capacity is not displayed
correctly.
• The remaining battery capacity display is merely a guideline.
To ensure that remaining battery capacity is displayed correctly,
use the battery completely from a fully-charged state, and
charge the battery again. (Remaining battery capacity may still
not be displayed correctly if the battery has been used for long
periods in high or low temperatures, or if the battery has been
recharged a large number of times.)
—
Shooting/recording
Cannot start shooting.
• Make sure the POWER/Mode selector switch is ON.
Page ꢀ5
Page 33
Cannot record even
through the SD Memory
Cards are inserted
correctly.
• Is the write-protect switch on the SD Memory Cards in the
“LOCK” position? The card cannot be recorded to if the switch
is in the “LOCK” position.
• Is the remaining memory available on the SD Memory Cards
extremely low? Please save contents onto different media and
delete unneeded data from the cards, or use new cards instead.
• Have the SD Memory Cards been correctly formatted?
Alternatively, are the cards of a format that is incompatible with
this camera? Reformat the cards with the camera.
Page 30
• 8 MB - 16 MB SD Memory Cards cannot be used.
Page 17
Page 17
Recording stops by itself.
• Is your SD Memory Card compatible with use for video
recording?
Always use SD Memory Cards compatible with use for video
recording.
There is a vertical
misalignment between the
left and right images.
• Adjust the images using the 3D FINE function, to minimize
misalignment. If the misalignment cannot be reduced to the
specified value even if adjusted with the 3D FINE function,
consult your dealer.
Page 45
—
There is focus
misalignment between the
left and right images.
• The focus may have been misaligned by shock applied to
the camera. Turn the power off then on again. If the focus
misalignment persists, consult your dealer.
(Continued on the next page)
85
Before calling for service (continued)
Playback
Cannot play even when I
press the play button.
• Is the PB lamp on? If the CAMERA lamp is on, press the
POWER/Mode selector switch so that the PB lamp turns on.
• Is the recording format correct?
Change to a recording format for proper playback.
• Are the SD Memory Cards inserted in reverse left-right order?
Insert the left and right SD Memory Cards correctly.
Page 57
Page 80
Page 30
Mosaic-like noise appears
when I cue or review a clip.
• This noise is inherent to digital video technology. This is normal.
—
A black screen appears
during clip changeover.
• When playing back multiple clips in succession, a black screen
appears at the changeover between clips. This is normal.
—
—
Images do not appear on
the television even though
I have connected the
• Make sure the input selector on your television is set to video
input. Read the television’s instructions carefully and select the
correct video input connector for the camera-recorder.
• Is the 3D setting correct on your television?
Read the television’s instructions carefully and select the
correct setting.
camera-recorder properly.
—
• Is the setting for the output terminal correct?
Set it correctly on the AV OUT SETUP screen.
Page 81
Page 65
Cannot hear any sound
from the camera-recorder’s
speaker.
• You may have turned down the camera-recorder’s volume
control too far.
Adjust the volume level using the AUDIO MON/ADV button +.
Other
There is a rattling sound
when the camera-recorder
is tilted back and forth.
• This is the sound of the lens moving. This is not a fault. No
sound should be heard when the camera’s power is switched
on.
—
—
A clicking sound is heard
when the power is turned
on.
• This initialization operation is performed when the camera starts
up. It occurs due to the construction of the camera and is not
indicative of any trouble.
The SD Memory Card
screen appears strange.
• The data on the card could be corrupted. Data can be corrupted
by static electricity and electromagnetic waves. Please always
save important data to a computer or other storage media.
—
The SD Memory Card
cannot be used even after
formatting.
• There could be a fault with the camera or with the SD Memory
Card. Please consult the place of purchase. Always use only
SD Memory Cards of 51ꢀ MB - 3ꢀ GB with this camera.
—
The camera does not
recognize the SD Memory
Card even though it is
inserted correctly.
• Was the inserted SD Memory Card originally formatted with
a computer? Always use this camera to format SD Memory
Cards. Please be aware that, when an SD Memory Card is
formatted, all data recorded on the card will be erased and will
not be restorable.
Page 30
The SD Memory Card is not • Please check that the device is compatible with the capacity or
Page 17
recognized when inserted
into other devices.
type (SD Memory Card/SDHC Memory Card) of the SD Memory
Card that you are using.
For details, please consult the device’s own operating
instructions.
86
Updating the firmware in the camera
Check firmware version of the unit with the SYSTEM INFO item on the setup menu OTHER
FUNCTIONS screen. Then access the site listed below to check the most recent firmware information
and download any firmware you require.
Download the update file to the unit by placing it on SD Memory Cards. For detailed information on the
update procedure, visit the below site.
• For updating, use only SD Memory Cards that comply with the SD or SDHC specifications.
• Be sure to insert two SD Memory Cards.
• Be sure to format SD Memory Cards on this unit.
87
Cleaning
Cleaning the Viewfinder
Eye cup holder
If there is dust inside the viewfinder, remove the
eye cup holder and get rid of the dust.
• The interior of the eye cup holder is specially
finished, so do not ever wipe it. If there is dust
on it, blow it off with an air blower.
Eye cup
• Remove the eye cup holder with the eye cup
attached by rotating it counterclockwise. (It will
be tightly screwed on.) When you do this, tilt
the viewfinder slightly upward.
• To mount the eye cup holder, align the ridges
and grooves of the eye cup holder and camera-
recorder, and turn clockwise until the holder
clicks into place.
Align the ridges with the grooves.
When cleaning, do not use benzene or
thinner.
• Using benzine or paint thinners may deform
the camera-recorder and/or cause the surface
finish to peel off.
• Before proceeding with maintenance, remove
the battery or disconnect the AC power cable
from the power outlet.
• Use a soft, clean cloth to wipe the camera-
recorder. To remove stubborn dirt, wipe the
camera-recorder with a cloth moistened with
kitchen detergent that has been diluted with
water and then use a dry cloth to take up the
remaining moisture.
88
Storage Precautions
Before storing the camera-recorder, remove the
SD Memory Cards and battery.
Store all of these items in a place with low
humidity and relatively constant temperature.
[Recommended temperature range: 15 °C to
ꢀ5 °C (59 °F to 77 °F)]
SD Memory Cards
• After ejecting an SD Memory Card from the
unit, be absolutely sure to stow it in its own
case.
• Do not leave SD Memory Cards in areas where
corrosive gases, etc. are present.
• Do not leave the cards inside vehicles, in
places exposed to direct sunlight or in other
places where the temperature is high.
• Do not leave the cards where the humidity level
is high or where there are high concentrations
of dust.
[Recommended relative humidity: 40 % to 60 %]
Camera-recorder
• Wrap the camera-recorder in a soft cloth to
keep the dust off.
Battery
• The battery life is shortened in places with
extreme temperatures.
• Storing the battery in a location with oily vapors
or high dust concentrations may corrode the
terminals or cause other damage, leading to
malfunction.
• Keep metal objects (such as necklaces and
hairpins) away from the terminals.
Short-circuiting may occur across the
terminals, causing the battery to heat up,
and you may seriously burn yourself if you
touch the battery in this state.
89
Recording format
When SYSTEM FREQ is set to 59.9 Hz
Recording mode
Frame rate
60
30P
ꢀ4P
1080/30P
(over 60i)
1080/ꢀ4P
(Native recording)
1080/60i
PH
1080/60i
7ꢀ0/60P
7ꢀ0/60P
When SYSTEM FREQ is set to 50 Hz
Recording mode
Frame rate
50
ꢀ5P
1080/ꢀ5P
(over 50i)
1080/50i
PH
1080/50i
7ꢀ0/50P
7ꢀ0/50P
• This product allows PH recording mode only.
90
How to handle data recorded on SD Memory Card
Data recorded in AVCHD format offers excellent
compatibility with computers due to the file type,
Drive: \
PRIVATE
but since this format includes not only video
and audio data, but also a variety of important
information, the folder structure will consist of file
associations as illustrated in the diagram on the
right. If even part of this information is modified
or deleted, the data may no longer be recognized
as AVCHD data, or the memory card may not
longer be able to be used with AVCHD devices.
AVCHD
AVCHDTN
BDMV
CLIPINF
PLAYLIST
STREAM
■Concerning the handling of the camera’s metadata
A special manufacturer area in the control file area under the AVCHD standard is employed for the
metadata which is supported by this camera.
If files are deleted or copied, if clip protection is added or removed or if other such editing operations
have been performed using editing software or a camera recorder which does not support this
camera’s metadata, the special area for the metadata will be erased, and the shot marks added
by the camera as well as the PH mode information and other information will be lost. Therefore,
before proceeding with these kinds of editing operations, check whether the camera’s metadata is
supported.
91
Specifications
[General]
• When SYSTEM FREQ is set to 50 Hz
Preset
50i/50P mode: 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50
seconds
ꢀ5P mode: 1/ꢀ5, 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50
seconds
Supply voltage:
DC 7.ꢀ V (when the battery is used)
DC 7.9 V (when the AC adaptor is used)
Power consumption: 17 W (recording)
Synchro scan
indicates safety information.
50i/50P mode: 1/50.0 to 1/ꢀ50.0 seconds
ꢀ5P mode: 1/ꢀ5.0 to 1/ꢀ50.0 seconds
Ambient operating temperature
0 °C to 40 °C (3ꢀ °F to 104 °F)
Ambient operating humidity
10 % to 80 % (no condensation)
Weight
[Video recording/playback]
Recording specification
AVCHD specifications
Compression method
MPEG-4 AVC/H.ꢀ64
Recording media
• Use an SD/SDHC Memory Card of class 4 or
above when recording.
Camera-recorder:
Approx. ꢀ.4 kg (5.3 lb) (excluding battery)
Approx. ꢀ.7 kg (6.0 lb) (with battery attached)
Dimensions (W × H × D)
158 mm × 187 mm × 474 mm (6-1/4 inches ×
7-3/8 inches × 18-11/16 inches)
(excluding the projecting part)
SD Memory Card:
51ꢀ MB, 1 GB, ꢀ GB (FAT1ꢀ and FAT16
formats)
SDHC Memory Card:
[Camera]
4 GB, 6 GB, 8 GB, 1ꢀ GB, 16 GB, 3ꢀ GB
(FAT3ꢀ format)
Recording format
Pickup devices
1/4.1-type MOS solid-state image sensing
device ×3 ×ꢀ
Picture elements
Effective picture elements: Approx. ꢀ,070,000
pixels ×3 (16:9) ×ꢀ
• When SYSTEM FREQ is set to 59.9 Hz
PH 1080/59.94i
PH 1080/ꢀ9.97P (over 59.94i)
PH 1080/ꢀ3.98P (native recording)
PH 7ꢀ0/59.94P
Lens
Motorized 5.6 x zoom,
F1.8 (WIDE) to Fꢀ.4 (TELE) (f=4.ꢀ mm to
ꢀ3.5 mm)
(35 mm equivalent: 47.1 mm to ꢀ64 mm), 16:9
Color separation optical system
Prism system
Distance between the optical axes
Approx. 60 mm (ꢀ-3/8 inches)
Minimum shooting distance
Approx.1.ꢀ m (47-1/4 inches) (all zoom range)
Reference plane adjustment range
• When SYSTEM FREQ is set to 50 Hz
PH 1080/50i
PH 1080/ꢀ5P
PH 7ꢀ0/50P
Transmission rate
PH mode: Approx. ꢀ1 Mbps (VBR)
Recording time (rough indication)
When a Panasonic SDHC Memory Card is
used
Capacity Recording time
(Recording mode: PH,
Approx. ꢀ.ꢀ m (86-5/8 inches) to
Gain settings
∞
19ꢀ0×1080 or 1ꢀ80×7ꢀ0 pixels)
0 to +ꢀ4 dB (variable in 1 dB steps)
Color temperature settings
3ꢀ00 K/5600 K preset, Ach, Bch
Shutter speed settings
• When SYSTEM FREQ is set to 59.9 Hz
Preset
4 GB
Approx. ꢀ1 min.
Approx. 45 min.
Approx. 90 min.
Approx. 180 min.
8 GB
16 GB
3ꢀ GB
60i/60P mode: 1/60, 1/100, 1/1ꢀ0, 1/ꢀ50
seconds
SD Memory Card slot
ꢀ slots (left/right)
30P mode: 1/30, 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50
seconds
ꢀ4P mode: 1/ꢀ4, 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50
seconds
Maximum number of clips to be recorded
continuously in an SD Memory Card
ꢀ00 clips (when formatting and recording
continues without removing the card)
Maximum number of clips to be played back
in an SD Memory Card
Synchro scan
60i/60P mode: 1/60.0 to 1/ꢀ50.0 seconds
30P mode: 1/30.0 to 1/ꢀ50.0 seconds
ꢀ4P mode: 1/ꢀ4.0 to 1/ꢀ50.0 seconds
ꢀ00 clips (up to ꢀ00 clips can be displayed)
9ꢀ
Thumbnail display
8 thumbnails/page
Editing functions
Delete, protect
Formatting
[Other inputs/outputs]
Camera remote
Super mini jack (ꢀ.5 mm diameter)×1 (ZOOM
S/S)
Mini jack (3.5 mm diameter)×1 (FOCUS, IRIS)
Super mini jack (ꢀ.5 mm diameter)×1 (CONV.)
Available
[Video System]
[Monitor]
Video output
LCD monitor
HDMI output: HDMI×1 (HDMI Type A
connector), 3D compatible (Not compatible
with VIERA Link)
3.ꢀ-type (16:9) LCD color monitor (approx.
9ꢀ1,000 pixels)
Viewfinder
0.45-type (16:9) LCD color viewfinder (approx.
1,ꢀꢀ6,000 pixels)
• When SYSTEM FREQ is set to 59.9 Hz
1080/59.94i Frame Packing, 1080/ꢀ3.98p
Frame Packing, 7ꢀ0/59.94p Frame Packing
1080/59.94i, 7ꢀ0/59.94p, 480/59.94p
• When SYSTEM FREQ is set to 50 Hz
1080/50i Frame Packing, 7ꢀ0/50 Frame
Packing, 1080/50i, 7ꢀ0/50p, 576/50p
[AC adaptor]
Power Source: 100 V - ꢀ40 V AC,
47 Hz - 63 Hz
0.55A
Power Output: 7.9 V DC, ꢀ.53 A
HD SDI 1(L) output: BNC×1, 0.8 V [p-p], 75 Ω
HD SDI 2(R) output: BNC×1, 0.8 V [p-p], 75 Ω
• When SYSTEM FREQ is set to 59.9 Hz
1080/59.94i, 1080/ꢀ3.98PsF, 7ꢀ0/59.94p
• When SYSTEM FREQ is set to 50 Hz
1080/50i, 7ꢀ0/50p
indicates safety information.
Weight
Approx. ꢀꢀ0 g (0.49 lb)
Dimensions (W x H x D)
4ꢀ mm × 31 mm × 104.4 mm (1-5/8 inches ×
1-1/4 inches × 4-1/8 inches)
[Audio System]
Compression method
Recording/playback: Dolby Digital/ꢀ ch
Sampling frequency
48 kHz
Quantization
16 bit
[Battery charger]
Power Source: 100 V - ꢀ40 V AC, 50/60 Hz
0.4 A
Power Output: 8.4 V DC, 1.ꢀ A
Compressed bit-rate
PH mode: 384 kbps
indcates safety information.
[Audio Input/Output]
Internal microphone
Stereo microphone
XLR input
XLR (3 pins) × ꢀ (INPUT1, INPUTꢀ)
High impedance
Weight
Approx. 160 g ( 0.35 lb)
Dimensions (W x H x D)
70 mm × 35 mm × 115 mm ( ꢀ-3/4 inches ×
1-3/8 inches × 4-1/ꢀ inches)
(excluding the projecting part)
LINE: 0 dBu
MIC: –50/–60 dBu (selectable in menu)
HDMI output
ꢀ ch (linear PCM)
Headphone output
Stereo mini jack (3.5 mm diameter)×1
Internal speaker
ꢀ0 mm (round)×1
Inrush current, measured according to European
standard EN55103-1: 6.5 A
Weight and dimensions are approximate.
Specifications are subject to change without
notice.
93
Index
Numerics
F
3D FINE function.............................................. 45
3D guide display............................................... 69
3D guide function.............................................. 38
3D image ....................................................11, 38
Fine adjustment between the two lenses ......... 45
Firmware........................................................... 87
FOCUS............................................................. 45
Focus
Auto focus.................................................. 36
Focus assist............................................... 36
Infinity ........................................................ 36
Manual focusing......................................... 36
Focus bar display ............................................. 69
A
AC adaptor ....................................................... ꢀ4
Audio equipment............................................... 48
AVCCAM Restorer............................................ 33
AVCHD ............................................................. 18
AVCHD-compatible equipment......................... 18
G
Gain.................................................................. 37
B
H
Battery.............................................................. ꢀ4
Black balance................................................... 41
Headphones..................................................... 66
C
I
Calendar........................................................... ꢀ8
CAMERA mode ................................................ 31
CARD FUNCTIONS ......................................... 63
Charging
Battery ....................................................... ꢀ3
Built-in battery............................................ 54
Clip
IRIS................................................................... 45
Iris..................................................................... 37
IRIS/CONV. dial..........................................37, 38
L
LCD monitor ..................................................... ꢀ7
M
Deleting...................................................... 6ꢀ
Information................................................. 63
Metadata.................................................... 50
Playback.................................................... 58
Protecting................................................... 6ꢀ
Color bar........................................................... 43
Convergence display..................................38, 69
Convergence point ............................................11
Adjustment................................................. 38
What is....................................................... 39
Counter............................................................. 53
Menu
Initializing................................................... 76
List............................................................. 78
Structure.................................................... 77
Using.......................................................... 75
Metadata
Contents .................................................... 50
Uploading................................................... 51
Microphone
Built-in microphone.................................... 48
External microphone............................48, 66
Phantom microphone................................. 49
MIX image ........................................................ 38
Monitor........................................................65, 67
D
Date and time................................................... 65
DIAL (IRIS/CONV.) selector switch.............37, 38
O
E
OPERATION..................................................... 6ꢀ
EXEC button..................................................... 45
Eye cup............................................................. ꢀ6
P
Parallactic angle............................................... 39
Parallax............................................................. 39
PB mode........................................................... 57
Progressive mode............................................. 35
94
R
W
REC CHECK .................................................... 31
Recording format.............................................. 90
Recording level................................................. 49
Remaining battery capacity display.................. 70
RESUME PLAY ................................................ 60
Resume playback............................................. 60
Warning display................................................ 71
Wave form ........................................................ 44
White balance
Adjustment................................................. 40
Preset ........................................................ 40
Z
S
Zebra pattern.................................................... 4ꢀ
Zoom ................................................................ 34
Safety zone....................................................... 69
Screen mode display........................................ 70
SD Memory Card
Access lamp .............................................. 3ꢀ
Card type................................................... 17
Formatting.................................................. 30
Inserting..................................................... 30
Protecting................................................... 33
Recorded data........................................... 91
Recording time........................................... 3ꢀ
Removing................................................... 33
Repairing ................................................... 33
Shooting ........................................................... 31
Shot mark...................................................44, 59
Shutter speed................................................... 46
Specifications ................................................... 9ꢀ
Synchro scan.................................................... 47
T
Tally lamp.......................................................... ꢀ5
Thumbnail
Display method.......................................... 61
Thumbnail screen...................................... 58
THUMBNAIL SETUP........................................ 61
Time code......................................................... 54
Time code display............................................. 68
TV...............................................................65, 67
U
User information ............................................... 56
V
VERTICAL........................................................ 45
Vertical misalignment........................................ 45
Viewfinder......................................................... ꢀ6
Volume
Adjusting while shooting............................ 44
Playback volume........................................ 65
95
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points, in accordance with your national legislation and the
Directives ꢀ00ꢀ/96/EC and ꢀ006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources
and prevent any potential negative effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please
contact your local municipality, your waste disposal service or the point of sale where you
purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items,
Cd
please contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies
with the requirement set by the Directive for the chemical involved.
|
Rockford Fosgate FRC2246 User Manual
PYLE Audio PiFM5 User Manual
Pioneer S DV440 User Manual
Pioneer DEH P7100BT User Manual
Pioneer AVH P4100DVD User Manual
Philips 55PFL66X6H User Manual
Panasonic PV L578 User Manual
Lennox Hearth BT 320S User Manual
Kodak CIS 106 User Manual
Kenwood KVT M700 User Manual