PYLE Audio View Series PLTDN71 User Manual

PLTDN71  
Single DIN Motorized 7" TFT Monitor DVD/AM/FM Receiver/TV-Tuner  
Safety precautions  
WARNING  
CAUTION  
To prevent injury or fire,Please  
take the following precautions:  
To prevent damage to the machine,  
take the following precautions:  
Do not operate when driving.  
Be sure to store the liquid crystal panel  
inside the main unit when parking the car  
outdoors for long time.  
To prevent electric,etc,Please do not  
let the metal goods(silver,coin,tools..)fall into  
the installation.  
If you smell or see smoke,turn off the  
power immediately and consult our dealer.  
Be careful not to drop or shock the unit  
strongly.  
Be sure the unit is connected to a 12V  
DC power with a Negative Ground.  
Do not install the unit in places where  
it is exposed to direct sunlight,high heat  
or humidity,water splash or dust.  
To change fuse,please use the same  
one in specification and capacity.  
When changing fuse,please do it  
after pulling down power wires to avoid  
short circuit.  
Do not touch the liquid crystal to avoid the  
life hurt.If the clothes is stained with it,Please  
clean it immediately by soap.  
In extremely cold weather, the display  
movement may slow down and the display  
may darken, but this is not a malfunction.  
Then display will work normally when the  
temperature increases.  
Do not place anything on the display  
when then panel is tilted.  
If the unit seems not work properly press  
the reset button to reset the memory of the  
unit.  
SRC  
ON/OFF  
ADJ  
OPEN/CLOSE  
APS  
MENU  
MUT  
BAND  
RESET  
RESET  
2
Electric Connection  
2
1
2
1
CD CHANGER  
RED LINE OUT F R  
WHITE LINE OUT F L  
BACK CAR VIDEO IN  
CAR ANTENNA  
SUB  
RED LINE OUT R R  
WHITE LINE OUT R L  
AUX LEFT IN  
AUX RIGHT IN  
VIDEO IN  
TV ANTENNA PLUG  
(Gray)  
Brake detecting wire  
VIDEO OUT  
(Purple)  
Detecting wire for back a car  
White  
To front left speaker  
To front right speaker  
To rear left speaker  
Connect control for antenna  
or remote control for amplifier  
White/Black  
(Blue)  
Ignition key  
switch  
Gray  
ACC wire  
(Red)  
Gray/Black  
Battery wire  
Car fuse box  
(Yellow)  
Green  
Green/Black  
Car fuse box  
(main fuse)  
Ground wire(Black)  
(To car chassis)  
Purple  
To rear right speaker  
Battery  
Light wire(Orange)  
Purple/Black  
3
Installation  
Before installing the receiver permanently, fit it in the approximate place in your car ,and connect the  
equipment according to the speakers and electrical connections. When  
your system is operated properly,(preferably with the  
car engine running), follow the instructions  
3)Support strap  
for permanent installation  
(supplied)  
of your system.  
INSTALL THE UNIT  
1)Install half sleeve, can be with or  
without adapter. It will fit better  
with adapter.  
2)Bend over some tabs to secure the  
half sleeve inside of dash.  
3) Support strap to be strutted under  
dash, secure this strip to avoid skipping  
of disc.  
2)Bend over tabs  
of half sleeve  
(supplied)  
1) Adapter  
(not supplied)  
Half sleeve  
(supplied)  
REMOVE THE UNIT  
Insert removal wrench into the small  
gap on the right side of the unit and pull  
the unit slightly out on the same side,  
then release the wrench. Repeat the  
same action for the left side. By now,  
you can remove the unit and unplug  
the wires connector.  
4) Two wrenches for releasing  
the unit (supplied)  
4
General Features  
SOURCE/POWER  
APS/PBC SRC/PWR  
MUTE  
OPEN/CLOSE  
Turn your car`s ignition key to ACC or ON position.  
On being off,please short press[SRC]and it can be  
turned on,and still keep the showing angle when it  
was turned off last time.  
ON:  
SRC  
ON/OFF  
OPEN/CLOSE  
ADJ  
APS  
MENU  
On being open,please long press[SRC] then it can  
be turned off.  
OFF:  
MUT  
BAND  
RESET  
SRC: On being open,please short press [SRC] then can  
transit among the following status.  
SEL/VOL  
N/P  
EJECT  
PLAY/PAUSE  
RADIO  
DVD  
Display Open/Close  
OPEN: Press[  
CLOSE: Press[  
Notes:  
](OPEN/CLOSE )  
](OPEN/CLOSE )again.  
CDC  
TV  
If the unit stops halfway,press[  
way in.  
]again and draw it all the  
AUX IN  
Opening/closing the display can also be done when the  
power is off.  
CDC/AUX IN can be skipped when no external devices are  
connected.  
WARNING  
Do not touch the unit while the display is moving. Inserting  
hands,fingers or foreign objects into the unit can cause  
injuries and damage to the unit.  
Keep babies and children away from the unit.  
5
General Features  
Mute  
Play/Pause  
Press the [MUT]button  
MUTE ON  
If with DISC in unit,Press the [  
]to pause music.  
Press the [MUT]button again.  
MUTE OFF  
Press the [  
]button again , come back DISC playing.  
If a disc is loaded,a sector sign will show on the display.  
7 inches wide LCD  
display  
N/P  
Under the playing, press [BAND] and can transit among  
PAL/AUTO/NTSC  
SOURCE  
ADJ ANGLE  
PBC  
Under the songs, press [APS] then show song content of  
disc and stop the playing song. If press again then com  
back the playing status.  
Eject  
APS  
MENU  
MUT  
Out  
Press the [ ]button to eject the disc out of the unit .  
BAND  
RESET  
6
General Features  
Display position Adjustment  
TFT-LCD adjustment  
Press the [MENU] button,it will show as follows:  
For smooth adjustment,make sure to first return the lateral angle to  
the neutral position and then adjust the tilt angle.  
Avoid physical shock on the display.  
PIC SEL  
STANDARD  
SOFT  
AS/PS  
ADJUST  
Tilt angle  
AS/PS  
ADJUST  
BRIGHTNESS  
USER  
Press [ADJ] button ,it can adjust screen  
angle gradationally.The unit has 4 grades  
for adjustment ,and each time you  
press the button ,it can move one  
grade down along indication; it can  
resume up along indication.  
AS/PS  
ADJUST  
APS  
MENU  
MUT  
15  
BAND  
RESET  
USER  
15  
15  
R
B
G
MODE  
16:9  
ADJ ANGLE  
Press  
or  
and  
to adjust.  
to remote cursor up and down,and press  
SOURCE  
ADJ ANGLE  
CAUTION  
In radio mode ,16:9 don t operation.  
Do not place any object on  
thedisplay unit,or subject it  
to undue force.  
Do not move the display  
forcibly.  
The monitor movable range  
may be limited by a type of  
car,a position where the  
display is mounted,etc.  
APS  
MENU  
IN-DASH 7INCH WIDE COLOR LCD TV WITH DVD RECEIVER  
MUT  
BAND  
RESET  
7
General Features  
Direct Channel Selection  
(Only for remote control)  
TV Tuner  
SOURCE  
Enter a channel number by pressing [0]to[9].  
Example:Channel Number 17  
press [1]and [7].  
SRC  
ON/OFF  
OPEN/CLOSE  
ADJ  
APS  
MENU  
MUT  
CD Changer  
BAND  
RESET  
(Only select sanyo CD Change 10disc or 6disc))  
CD Change/Video CD Change Mode  
N/P  
Preparation:  
To receiver TV broadcasts,install the TV antenna.  
Press [MODE] to change to CD/Video CD Change mode and  
playback starts.  
For receiving TV broadcasts, stop your car where there is no  
obstacle to broadcast reception around.  
Disc Selection  
[
[
](CHANNEL):Up  
](CHANNEL):Down  
TV mode  
Press [MODE] to change to TV mode.  
Channel Selection  
[
[
](CHANNEL):Up  
](CHANNEL):Down  
How to set clock  
Channel Search  
Long press the [APS] button and automatically search and keep  
TV station  
Press [CLOCK] button can show clock.  
Long press [CLOCK] button,when hour hand twinkling,  
press VOL- or VOL+ to adjust hour.then Press [CLOCK]  
button,when minute hand twinkling,press VOL- or VOL+ to  
adjust minute.  
Transit the channels (Page 14)  
Under TV mode, press [N/P] button to switch the TV audio style.  
8
Speaker setting  
BAL set mode  
Speaker mode  
Press SEL/VOL button fourth, display will show BAL  
on,then rotate the button to adjust BAL level up/down  
in different direction.  
VOL  
EQ  
BAS  
TRE  
BAL  
FAD set mode  
FAD  
Press SEL/VOL button fifth, display will show FAD  
on,then rotate the button to adjust FAD level up/down  
in different direction.  
EQ set mode  
VOL set mode  
Press SEL/VOL button sixth, display will show EQ  
on,can be select sound effect:  
Press SEL/VOL button once,display will show VOL  
on,then rotate the button in clockwise direction to  
increase volume level;rotate the button in anticlockwise  
direction todecrease volume level.  
NORM  
Once  
BAS set mode  
FLAT  
Twice  
Third  
Press SEL/VOL button twice,display will show BAS  
on,then rotate the button to adjust bass level up/down  
in different direction.  
CLAS  
ROCK  
POP  
TRE set mode  
Fourth  
Fifth  
Press SEL/VOL button third,display will show TRE  
on,then rotate the button to adjust treble level up/down  
in different direction.  
9
Radio Operation  
Tuner  
AS/PS  
In radio mode:  
manual tuning:  
short press  
SRC  
ON/OFF  
OPEN/CLOSE  
ADJ  
button it can select higher frequency station.  
can select lower frequency station.  
Short press  
APS  
MENU  
MUT  
Auto loading tuning:  
BAND  
RESET  
the long press  
button it can automatically select higher  
frequency station. And the long press  
select lower frequency station.  
it can automatically  
BAND  
SEEK  
Select station  
Press [APS]button  
Seek Tune:  
In FM (FM1 FM2 FM3) or AM(AM1 AM2 playing mode, long  
press "APS" button, it can seek and store strong frequecy  
station automatically in to1-6 memory buttons.  
FM can memorize 18 stationns. AM can memorize 12 stations.  
Band  
Selecting band  
Press BAND button to select among three FM or two AM bands.  
(FM1-FM2-FM3-AM1-AM2)  
FM1  
FM2  
FM3  
AM2  
AM1  
10  
Remote control  
Loading and replacing the battery  
Use one lithium battery(CR2025)  
Insert the batteries with the +and - poles aligned properly.  
Following the illustration inside the case.  
MUTE  
SOURCE  
DI-  
SEL  
CLK  
DI+  
APS  
EQ  
Pull out  
WARNING  
Store unused batteries out of the reach of children.contact a  
doctor immediately if the battery is accidentally swallowed.  
Title  
Do not set the remote on hot places such as the above dashboard.  
OSD  
N/P  
R/L  
GOTO  
AF  
TA  
PTY  
11  
Basic operation  
POWER  
VOL+/VOL-  
Press this button can increase or decrease volume.  
Press this button to turn on/off the unit.  
CLK  
APS/PRG  
Under receiving position,press this button can do seek station  
;under VCD,CD playing,press this button can play programe.  
Press this button can show the time,and long press to enter clock  
adjustment.  
Play/pause  
SOURCE  
Press this button can switch between play and pause.Under stop  
state, similarly press it to play.  
Press this button can select needed receiving and playing mode.  
ST/RPT  
SEEK+/SEEK-  
Under receiving state,press this button can select stereo or single  
track;under playing state,it can play repeat.  
Press this button can manually search tune,fast,back and track  
searching control.  
N/P(Angle)  
SEL  
N/P  
Repeatfully press this button can select needed mode.  
Under the playing, press [N/P] and can transit among  
PAL/AUTO/NTSC  
Angle  
BAND RDM  
In DVD mode, Long press can adjust the angle of the video.  
(The DVD disc record the angle with this function.)  
Under receiving position,press this button can select band;  
under VCD,DVD position,press this button can play randomly.  
12  
Basic operation  
[ENTER]  
[ ][ ][ ][ ]  
Under DVD mode, press this button can move cursor in  
up,down,left and right directions after entering SETUP  
Menu.Press ETR button can confirm selected item.  
MUTE  
SOURCE  
DI-  
DI+  
Press this button once to stop play music .  
APS  
SEL  
EQ  
CLK  
SETUP  
Under playing mode, press this button can open SETUP Menu.  
Title  
TITLE  
OSD  
N/P  
R/L  
Under VCD mode,press this button to enter Menu selection same as  
PBC.  
Under DVD mode,press this button to return to the top of Menu.  
GOTO  
AF  
TA  
PTY  
13  
Basic operation  
SUBTITLE  
0-10+  
Under DVD mode,press this button can switch dialogue language.  
Press this button can directly select track and chapter,and 1-6  
buttons can select preseted stations.  
MUTE  
SOURCE  
DI-  
SEL  
CLK  
DI+  
R.L/LANGUAGE  
APS  
Under VCD mode,press this button can switch track.  
Under DVD mode,press this button can switch dialogue language.  
EQ  
When playing DVD, long press this button for 3 seconds, sound can  
be switched between 4.0CH and 5.1CH.  
Under TV mode, press this button to switch the TV audio style.  
Title  
MUTE  
Press this button to turn off volume out ,and again to resume.  
OSD  
N/P  
R/L  
OSD  
Press this button can show play time, surplus time.  
EQ  
GOTO  
Press SEL/VOL button fifth, display will show EQ on,can  
be select sound effect:  
AF  
TA  
PTY  
FLAT CLAS ROCK POP  
14  
Accessories  
External view  
External view  
........ Number of items  
........ Number of items  
1
3
............1  
............2  
2
............1  
The use of any accessories except of those provided  
might result in damage to the unit .Make sure only to  
use the accessories shipped with the unit ,as shown  
above.  
15  
Specifications  
Specifications subject to change without notice.  
DISPLAY UNIT  
GENERAL  
Liquid crystal panel.........................................7 inches wide  
Display weight ...........................................................1.7kg  
Number of pixels............................................33,6960 pixels  
Display method........................Transparent color filter format  
Drive method....................................TFT (thin film transistor)  
active matrix format  
Operating power....................................12 Volts DC,negative  
ground  
%10THD output wiring.........................Designed for using four  
speakers only front and rear  
channels cannot be combined  
in use with 2speakers.  
Light source.....................................................internal light  
(built-in small fluorescent lamp)  
Load impedance..................................compatible 4 to 8 ohm  
speakers  
Fuses............................................................ ..........10 amp  
Dimensions......................... 187mm(L)x170mm(W)x50mm(H)  
Weight......................................................................2.5Kgs  
FM Tuner  
Tuning range..................................EUROPE:87.5-108.0MHz  
(50KHz step)  
USA:87.5-107.9MHz  
(200KHz step)  
FM usable sensitivity(S/N=30dB)...............................<12dB  
Stereo separation......................................................>45dB  
AM Tuner  
Tuning range.....................................EUROPE:522-1620KHz  
(9KHz step)  
USA:530-1710KHz  
(10KHz step)  
AM sensitivity..............................................................28dB  
16  
Trouble shooting guide  
What might seem to be a malfunction in your unit may just be the result  
of slight misoperation or miswiring.Before calling service, first check the  
following table for possible problems.  
?Noise on both Radio and CD  
?The tilt angle or the front-rear position of the display is  
not adjustable.  
There is an obstacle  
Poor ground,dirty or corroded at the car Battery posts  
Check the black wire for proper grounding clean and tighten ground  
connection.  
Install the unit where the unit moves freely.  
?No/Poor sound on one or more speakers  
Speakers or speaker wiring or volume, Balance and  
Fader setting  
?The display does not go back into the unit.  
The display stops on the way to the home position.  
Press [  
](OPEN/CLOSE)  
Check the speaker wiring and test the speakers all in good condition  
check the setting of volume, Balance and Fader controls.  
?The power does not turn ON.  
The fuse has blown.  
?CD sound skips  
Confirm whether the lead short circuit,then replace fuse with same capacity.  
Installation the unit angle is greater than 45 ,or  
mounting is not fixed and the back strap is not secure.  
?NO Sound.  
Adjust the unit with mounting angle less than 45 and make sure the  
unit is mounted securely and tighten with the back strap(supplied)  
The cable connect incorrectness.  
Exactitude connect of the cable.  
?Unit completely inoperative, no Light and Sound  
Incorrect wire connection, Power RED/YELLOW or  
Ground wire or Blown fuse  
?Noise on Radio or poor recepiton  
Antenna and Antenna Cable.  
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to  
+12 Volts battery and black wire to ground. Check Fuse with red/yellow  
wire, or check the fuse block on your car.  
Check antenna and antenna cable, the antenna base must be  
grounded and connected with good condition, replace  
antenna or antenna cable if needed.  
17  
OWNER'S MANUAL  
Before installation and operating the unit please read  
this manual thoroughly and retain  
it for future reference  

Razor Bicycle Accessories 25143060 User Manual
Radio Shack 240 User Manual
Pioneer Car Stereo System DEH 2150UB User Manual
Pioneer Car Amplifier SA 9900 User Manual
Panasonic CQ C8100U User Manual
Motorola H715 User Manual
Loewe Network Mediaplayer Accessories TV User Manual
Legacy Car Audio LCDCS92 User Manual
KitchenAid KFPW760QWH0 User Manual
Kenwood KRC 379R User Manual