PAC Car Amplifier User Manual

TATO  
JBL Amplifier Turn-On Interface for  
Toyota CANbus Vehicles  
Class 2  
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0  
J1850  
Class 2  
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0  
The TATO is designed to control the power and audio levels of the factory installed  
JBL amplifier allowing the OEM radio to be removed and replaced with an aftermarket  
stereo.  
Installation:  
Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE  
RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED  
WITH REMOVING THE FACTORY RADIO  
Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the  
following connections of the TATO wiring harness to the aftermarket radio:  
Connections:  
Yellow Wire  
- Connect to 12 Volt Constant Power on aftermarket radio  
- Connect to Accessory on aftermarket radio  
- Connect to Ground on aftermarket radio  
- Connect to Dimmer on aftermarket radio  
- Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately)  
- Connect to Accessory  
Red Wire  
Black Wire  
Orange/White Wire  
*11 Pin Harness  
Red Bullet Connector  
Black Bullet Connector - Connect to Ground  
Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio  
Front Left - White RCA  
Front Right - Grey RCA  
Rear Left - Green RCA  
Rear Right - Purple RCA  
If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs  
of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck.  
Connections to the TATO Interface:  
• Connect 24-pin translucent connector  
to the side of the TATO.  
• Connect 8-pin DIN cable to the plug on  
the side of the TATO.  
Connections to the Vehicle:  
• Plug the main 20-pin Toyota harness into the matching factory wir-  
ing harness.  
*If using PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2, Plug  
the smaller 20-pin harness into the matching factory wiring har-  
ness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2  
for version #8 and follow the programming instructions included  
with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2.  
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in  
connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume  
obligation or liability in relation to the TATO other than its replacement.  
Pacific Accessory Corporation - Santa Ana, CA 92705  
06-29-10  

Pentax C7528 User Manual
Optimus CD 8400 User Manual
Motorola H680 Wireless Earset Over the ear 89182N User Manual
Milwaukee 9571 User Manual
KitchenAid ULTRA POWER 5KSB52XXXX User Manual
Kenwood SIRIUS DT 7000S User Manual
Kenwood KDC HD545U User Manual
Kenwood KDC BT30 User Manual
Kenwood CD RECEIVER KDC 2026 User Manual
JVC LYT1353 001B User Manual