INSTALLATION INSTRUCTIONS FOR PART 99-7610
INSTALLATION INSTRUCTIONS FOR PART 99-7610
APPLICATIONS
2007-up
Nissan Versa
2011 Nissan Juke
99-7610B
99-7610HG
KIT FEATURES
• DIN head unit provisions with pocket
• ISO DIN head unit provision with pocket
• Double DIN mount radio provision
• B = Matte Black
• HG = Gloss Black
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) DDIN Trim Plate
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-7552 - 2007-up Nissan Harness
• 40-NI12 - 2007-up Nissan Antenna Adapter
A
B
D
C
TOOLS REQUIRED:
Panel RemovalTool • Phillips Screwdriver
Socket Wrench
METRA. THE WORLD’S BEST KITS.™
metraonline.com
1-800-221-0932
© COPYRIGHT 2011 METRA ELECTRONICS CORPORATION
99-7610 DASH DISASSEMBLY
2007-UP NISSAN VERSA
1. Unclip and remove the panel above
the radio. (Figure A, B)
2. Remove (2) Phillips screws securing
the radio trim panel then unclip and
remove the entire panel surrounding
the radio and a/c controls. (Figure C)
3. Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure D)
Continue to kit assembly.
Figure C
RADIO
PRESET A-B-C
CD
LOAD
DISP
CLOCK
6CD CHANGER
RPT
SCRL
1
2
3
4
RDM
SEEK
TUNE
FF-REW
FOLDER
PUSH
PWR
TRACK AUDIO
FILE
5
6
AUX
SCAN
CAT
VOL
CH
Figure A
Figure D
Figure B
1
99-7610 DASH DISASSEMBLY
2011 NISSAN JUKE
1. Unclip and remove the climate control
panel. (Figure A)
2. Remove (2) Phillips screws securing
the radio trim panel. (Figure B)
3. Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure C)
Continue to kit assembly.
Figure A
Figure B
Figure C
2
99-7610
DIN HEAD UNIT PROVISION
Note: You will need to remove the after-
market radio’s trim ring if equipped.
Nissan Juke
1. Cut and remove the appropriate tabs
not necessary for your application.
(Figure A)
Nissan Versa
Nissan Juke
2. Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
3. Slide the aftermarket head unit into
Figure A
Figure B
Figure C
the cage and secure. (Figure C)
4. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
5. Attach the trim plate supplied with
the kit to the front of the radio
housing assembly. (Figure C)
6. Reassemble dash in reverse order
of disassembly.
3
99-7610
ISO MOUNT RADIO PROVISION
Note: The following modification will
need to be made to both ISO brackets
when using the ISO mount radio
provision. Cut or trim the area shown
from the ISO bracket. (Figure A)
1. Cut and remove the appropriate tabs
not necessary for your application.
(Figure B)
Continued on page 5.
FRONT
FACE-
RIGHT
SIDE
BRACKET
Figure A
Nissan Juke
Nissan Versa
Nissan Juke
Figure B
4
99-7610
1. Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure C)
2. Slide the head unit into the radio
opening until the side clips engage.
(Figure D)
3. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
4. Attach the trim plate supplied with
the kit to the front of the radio
housing assembly. (Figure D)
Figure C
5. Reassemble dash in reverse order
of disassembly.
Figure D
5
99-7610
DOUBLE DIN MOUNT RADIO PROVISION
1. Mount the factory brackets
(removed from factory radio during
disassembly) to the sides of the
double DIN radio using screws
supplied with the double DIN radio.
(Figure A)
2. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
3. Place the DDIN trim plate on the front
of the DDIN radio. (Figure B)
Figure A
4. Reassemble dash in reverse order
of disassembly.
Figure B
6
99-7610
NOTES
99-7610
NOTES
99-7610
NOTES
INSTALLATION INSTRUCTIONS FOR PART 99-7610
METRA. THE WORLD’S BEST KITS.™
metraonline.com
1-800-221-0932
© COPYRIGHT 2011 METRA ELECTRONICS CORPORATION
|