OWNER’S MANUAL
Streaming
Blu-ray Disc™ Player
Please read this manual carefully before operating
your set and retain it for future reference.
BP330
P/NO : MFL67732308_REV1.0
Getting Started
3
This device is equipped with a portable battery or
accumulator.
Safe way to remove the battery or the battery
from the equipment: Remove the old battery
or battery pack, follow the steps in reverse order
than the assembly. To prevent contamination
of the environment and bring on possible
1
threat to human and animal health, the old
battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery should not be exposed
to excessive heat such as sunshine, fire or the like.
FCC Compliance Statement
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
y
y
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
y
y
Consult the dealer or an experienced radio/TV
technician for help.
4
Getting Started
CAUTION: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
Notes on Copyrights
Because AACS (Advanced Access Content
System) is approved as content protection
system for Blu-ray Disc format, similar to use of
CSS (Content Scramble System) for DVD format,
certain restrictions are imposed on playback,
analog signal output, etc., of AACS protected
content. The operation of this product and
restrictions on this product may vary depending
on your time of purchase as those restrictions
may be adopted and/or changed by AACS after
the production of this product.
y
1
FCC RF Radiation Exposure Statement : This
equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body. End users must follow the
specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter.
Furthermore, BD-ROM Mark and BD+ are
additionally used as content protection systems
for Blu-ray Disc format, which imposes certain
restrictions including playback restrictions for
BD-ROM Mark and/or BD+ protected content. To
obtain additional information on AACS, BD-ROM
Mark, BD+, or this product, please contact an
authorized Customer Service Center.
y
CAUTION: Regulations of the FCC and FAA prohibit
airborne operation of radio-frequency wireless
devices because their signals could interfere with
critical aircraft instruments.
Responsible Party :
LG Electronics USA, Inc.1000 Sylvan Avenue
Englewood Cliffs, NJ 07632
Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
y
y
TEL. : +1-800-243-0000
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
y
Getting Started
5
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
IMPORTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
1
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold
with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
6
Table of Contents
4
Operating
Table of Contents
31
General Playback
31 – Using [HOME] menu
31 – Playing a disc
31 – Playing a file on disc/USB device
32 – Enjoying BD-Live™
32 – Basic operations for video and audio
content
33 – Basic operations for photo content
33 – Using the disc menu
33 – Resume playback
1
Getting Started
2
8
8
Safety Information
Introduction
– Playable discs and symbols used in
this manual
– About the “7” symbol display
– Regional code
9
9
9
33 – Last scene memory
34 Advanced Playback
34 – Repeat playback
– LG AV Remote
10 Remote Control
11
11
Front Panel
Rear Panel
34 – Repeating a specific portion
34 – Viewing content information
35 – Changing content list view
35 – Selecting a subtitle file
35 – Changing the mode
36 – Options while viewing a photo
36 – Listening to music during slide show
37 – Playing a file on a network server
38 Using Home Network Server for PC
38 – Installing Nero MediaHome 4
Essentials
38 – Sharing files and folders
39 – About Nero MediaHome 4 Essentials
39 – System requirements
40 On-Screen Display
40 – Displaying content information on-
screen
2
Connecting
12
12
Connecting the AC Adapter
Connecting to your TV
13 – What is SIMPLINK?
14 – Resolution setting
15
15 – Connecting to an amplifier via HDMI
output
16 – Connecting to your Home Network
16 – Wired network connection
16 – Wired network setup
Connecting to an Amplifier
18 – Wireless network connection
19 – Wireless network setup
22 USB Device Connection
41 – Playing from selected time
41 – Selecting a subtitle language
41 – Hearing a different audio
41 – Watching from a different angle
42 – Changing the TV aspect ratio
42 – Changing subtitle code page
42 – Changing the picture mode
43 Audio CD Recording
22 – Playback content in the USB device
3
System Setting
23 Initial Setup
24 Settings
24 – Adjust the setup settings
24 – [DISPLAY] menu
26 – [LANGUAGE] menu
26 – [AUDIO] menu
28 – [LOCK] menu
29 – [NETWORK] menu
30 – [OTHERS] menu
44 Using the Premium
Table of Contents
7
5
Troubleshooting
45 Troubleshooting
45 – General
46 – Network
47 – Picture
1
47 – Customer support
47 – Open source software notice
2
3
4
5
6
6
Appendix
48 Controlling a TV with the Supplied
Remote Control
48 – Setting up the remote to control your
TV
49 Network Software Update
49 – Network update notification
49 – Software update
51
Additional Information
51 – File requirement
52 – AVCHD (Advanced Video Codec High
Definition)
53 – About DLNA
53 – Certain system requirements
53 – Compatibility notes
54 Audio Output Specifications
55 Area Code List
56 Language Code List
57 Trademarks and Licenses
59 Specifications
60 Maintenance
60 – Handling the unit
60 – Notes on discs
61
Important Information Relating to
Network Services
Some of contents in this manual may differ from your player depending on the software of the
player or your service provider.
8
Getting Started
Introduction
1
Playable discs and symbols used in this manual
Media/Term
Logo
Symbol
Description
Discs such as movies that can be purchased or
rented.
y
e
BD-R/RE discs that are recorded in BDAV format.
y
y
Blu-ray
BD-R/RE discs that contain Video, Audio or
Photo files.
y
u
i
ISO 9660+JOLIET, UDF and UDF Bridge format
y
y
Discs such as movies that can be purchased or
rented.
r
Video mode and finalized only
Supports the dual layer disc also
y
y
DVD-ROM
DVD-R
Finalized AVCHD format
DVD-RW
DVD+R
o
DVD+RW
(8 cm, 12 cm)
DVD R/RW discs that contain Video, Audio or
Photo files.
y
y
y
u
i
ISO 9660+JOLIET, UDF and UDF Bridge format
DVD-RW (VR)
(8 cm, 12 cm)
VR mode and finalized only
Audio CD
r
t
Audio CD
(8 cm, 12 cm)
CD-R/RW discs that contain Video, Audio or
Photo files.
y
y
y
u
i
CD-R/RW
(8 cm, 12 cm)
ISO 9660+JOLIET, UDF and UDF Bridge format
Indicates special notes and operating features.
Note
–
–
,
>
Indicates cautions for preventing possible damages
from abuse.
Caution
Getting Started
9
Note
,
About the “ ” symbol display
7
Depending on the conditions of the
recording equipment or the CD-R/RW (or
DVD R/RW) disc itself, some CD-R/RW (or
DVD R/RW) discs cannot be played on the
unit.
y
“7”may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
1
Depending on the recording software & the
finalization, some recorded discs (CD-R/RW,
DVD R/RW, BD-R/RE) may not be playable.
y
y
Regional code
This unit has a regional code printed on the rear of
the unit. This unit can play only BD-ROM or DVD
discs labeled same as the rear of the unit or“ALL”.
BD-R/RE, DVD R/RW and CD-R/RW discs
recorded using a personal computer or a
DVD or CD Recorder may not play if the
disc is damaged or dirty, or if there is dirt or
condensation on the player’s lens.
LG AV Remote
You can control this player with your iPhone
or Android phone via your home network. This
player and your phone must be connected to your
wireless network device such as access point. Visit
“Apple iTunes”or“Google Android Market (Google
Play Store)”for detailed information of“LG AV
Remote”.
If you record a disc using a personal
computer, even if it is recorded in a
compatible format, there are cases in which
it may not play because of the settings of
the application software used to create the
disc. (Check with the software publisher for
more detailed information.)
y
This player requires discs and recordings to
meet certain technical standards in order to
achieve optimal playback quality.
y
y
Pre-recorded DVDs are automatically set to
these standards. There are many different
types of recordable disc formats (including
CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions
to ensure compatible playback.
Customers should note that permission
is required in order to download MP3 /
WMA files and music from the Internet.
Our company has no right to grant such
permission. Permission should always be
sought from the copyright owner.
y
y
You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting
the option to Live System, you cannot use
it on LG player. (Mastered/Live File System :
Disc format system for windows Vista)
10 Getting Started
Remote Control
• • • • • • a • • • • • •
• • • • • • d • • • • •
1
1(POWER): Switches the player Colored (R, G, Y, B) buttons:
ON or OFF.
Use to navigate BD-ROM menus.
They are also used for [MOVIE],
[PHOTO], [MUSIC] and [Premium]
menu.
B(OPEN/CLOSE): Opens and
closes the disc tray.
0-9 numerical buttons: Selects
numbered options in a menu.
TV Control Buttons: See page
CLEAR: Removes a number when
setting the password.
REPEAT (h): Repeats a desired
section or sequence.
• • • • • • b • • • • •
c/v(SCAN): Searches
backward or forward.
C/V(SKIP): Goes to the
next or previous chapter / track /
file.
Z(STOP): Stops playback.
d(PLAY): Starts playback.
M(PAUSE): Pauses playback.
• • • • • • c • • • • •
HOME (n): Displays or exits the
[Home].
TITLE/POPUP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
Battery installation
INFO/MENU (m): Displays or
exits On-Screen Display.
Direction buttons: Selects an
option in the menu.
ENTER (b): Acknowledges menu
Remove the battery cover on the
rear of the Remote control, and
insert the R03 (size AAA) battery
with 4and 5matched correctly.
selection.
BACK (1): Exits the menu or
returns to the previous screen.
?: This button is not available.
DISC MENU: Accesses menu on a
disc.
Getting Started 11
Front Panel
1
a Disc Tray
d B(OPEN / CLOSE)
e 1/!(POWER)
f USB Port
b Power Indicator
c Remote Sensor
Rear Panel
a DC 12V IN
c HDMI OUT
b LAN port
12 Connecting
Connecting the AC
Adapter
Connect the unit to the power supply with the
supplied AC adapter.
Connecting to your TV
If you have a HDMI TV or monitor, you can connect
it to this player using a HDMI cable (Type A, High
Speed HDMI™ Cable). Connect the HDMI jack on
the player to the HDMI jack on a HDMI compatible
TV or monitor.
Rear of the unit
Rear of the unit
2
HDMI
Cable not
included
HDMI
cable
TV
Plug into a
power source.
Contact an electrical parts distributor for
assistance in selecting a suitable AC plug adapter
or AC cord set.
y
y
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
This AC adapter is manufactured by APD Group
Yang Ming Industrial.
Note
,
Please refer to the manuals of your TV, Stereo
system or other devices as necessary to make
the best connections.
Caution
>
Only use the AC adapter supplied with this
device. Do not use a power supply from
another device or manufacturer. Using any
other power cable or power supply may cause
damage to the device and void your warranty.
Connecting 13
Additional information for HDMI
What is SIMPLINK?
When you connect a HDMI or DVI compatible
device make sure of the following:
y
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
-
Try switching off the HDMI/DVI device and
this player. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this player.
Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power Off, etc.
-
-
The connected device’s video input is set
correctly for this unit.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
2
The connected device is compatible with
720x480p, 1280x720p, 1920x1080i or
1920x1080p video input.
LG TV’s with SIMPLINK function has the logo as
shown above.
Not all HDCP-compatible HDMI or DVI devices
will work with this player.
y
Note
,
Depending on the disc type or playing status,
some SIMPLINK operation may differ from your
purpose or not work.
-
The picture will not be displayed properly
with non-HDCP device.
Note
,
If a connected HDMI device does not accept
y
the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.
When you use HDMI connection, you can
change the resolution for the HDMI output.
y
y
y
Select the type of video output from the
HDMI OUT jack using [HDMI Color Setting]
option on the [Setup] menu (page 25).
Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the player and then turn it
on again.
When the HDMI connection with HDCP
is not verified, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
y
y
If there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m(15 ft.)).
14 Connecting
Note
,
Resolution setting
The player provides several output resolutions for
HDMI OUT jack. You can change the resolution
using [Setup] menu.
If your TV does not accept the resolution
you have set on the player, you can set
resolution to 480p as follows:
y
1. Press Bto open the disc tray.
1. Press HOME (n).
2
Press Z(STOP) for more than 5 seconds.
2. Use A/Dto select the [Setup] and press ENTER
If you select a resolution manually and then
connect the HDMI jack to TV and your TV
does not accept it, the resolution setting is
set to [Auto].
y
y
(b). The [Setup] menu appears.
3. Use W/Sto select [DISPLAY] option then
press Dto move to the second level.
2
4. Use W/Sto select the [Resolution] option
If you select a resolution that your TV
does not accept, the warning message
will appear. After resolution change,
if you cannot see the screen, please
wait 20 seconds and the resolution will
automatically revert back to the previous
resolution.
then press ENTER (b) to move to the third level.
The 1080p video output frame rate may
be automatically set to either 24 Hz or
60 Hz depending both on the capability
and preference of the connected TV and
based on the native video frame rate of the
content on the BD-ROM disc.
y
5. Use W/Sto select the desired resolution then
press ENTER (b) to confirm your selection.
Connecting 15
Connecting to an amplifier via
HDMI output
Connect the player’s HDMI OUT jack to the
corresponding in jack on your amplifier using a
HDMI cable.
Connecting to an
Amplifier
Make one of the following connections, depending
on the capabilities of your existing equipment.
HDMI audio connection (page 15)
Digital audio connection (page 16)
y
y
Rear of the unit
Since many factors affect the type of audio output,
see“Audio output specifications”for details (page
2
About Digital Multi-channel sound
A digital multi-channel connection provides the
best sound quality. For this, you need a multi-
channel Audio/Video Receiver that supports one
or more of the audio formats supported by your
player. Check the logos on the front of the Audio/
Video receiver and the manual. (PCM Stereo, PCM
Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby
TrueHD, DTS and/or DTS-HD)
HDMI cable
Receiver/Amplifier
HDMI
cable
TV
Connect the amplifier’s HDMI output jack to HDMI
input jack on your TV using a HDMI cable if your
amplifier has HDMI output jack.
You will need to activate the player’s digital output.
16 Connecting
Connecting to your
Home Network
Broadband
service
This player can be connected to a local area
network (LAN) via the LAN port on the rear panel or
the internal wireless module.
By connecting the unit to a broadband home
network, you have access to services such as
software updates, BD-Live interactivity and online
content services.
2
Router
Wired network connection
Using a wired network provides the best
performance, because the attached devices
connect directly to the network and are not subject
to radio frequency interference.
Please refer to the documentation for your network
device for further instructions.
DLNA certified servers
Connect the player’s LAN port to the corresponding
port on your Modem or Router using a
commercially available LAN or Ethernet cable.
Note
,
When plugging or unplugging the LAN
cable, hold the plug portion of the cable.
When unplugging, do not pull on the LAN
cable but unplug while pressing down on
the lock.
y
Rear of the unit
Do not connect a modular phone cable to
the LAN port.
y
y
Since there are various connection
configurations, please follow the
specifications of your telecommunication
carrier or internet service provider.
Wired network setup
If there is a DHCP server on the local area network
(LAN) via wired connection, this player will
automatically be allocated an IP address. After
making the physical connection, a small number of
home networks may require the player’s network
setting to be adjusted. Adjust the [NETWORK]
setting as follow.
If you want to access content from DLNA
servers, this player must be connected to
the same local area network thru a router.
y
y
To set your PC as a DLNA server, install the
supplied Nero MediaHome 4 on your PC.
Preparation
Before setting the wired network, you need to
connect the broadband internet to your home
network.
Connecting 17
1. Select [Connection Setting] option in the
[Setup] menu then press ENTER (b).
2
2. Read the preparations for the network settings
and then press ENTER (b) while [Start] is
highlighted.
Network will automatically be connected to the
unit.
18 Connecting
Advanced setting
If you want to set the network settings manually,
use W/Sto select [Advanced Setting] on the
[Network Setting] menu and press ENTER (b).
Wireless network connection
Another connection option is to use an Access Point
or a wireless router. The network configuration and
connection method may vary depending on the
equipment in use and the network environment.
1. Use W/Sto select [Wired] and press ENTER
(b).
2
Wireless
communication
2. Use W/S/A/Dto select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
Access point or
Wireless router
Broadband
service
Note
,
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/
A/Dand numerical buttons. If you make a
mistake while entering a number, press CLEAR
to clear the highlighted part.
Refer to the setup instructions supplied with
your access point or wireless router for detailed
connection steps and network settings.
For best performance, a direct wired connection
from this player to your home network’s router or
cable/DSL modem is always the best option.
If you choose to use the wireless option, please
note that performance can sometimes be affected
by other electronic devices in the home.
3. Select [Next] and press ENTER (b) to apply
network settings.
Network connection status is displayed on the
screen.
4. Press ENTER (b) while [Close] is highlighted to
finish the wired network settings.
Connecting 19
Wireless network setup
For the wireless network connection, the player
needs to be set up for network communication.
This adjustment can be done from the [Setup]
menu. Adjust the [NETWORK] setting as follow.
Setting up the access point or the wireless router
is required before connecting the player to the
network.
Note
,
WEP security mode generally have 4 keys
available on an access point setting. If your
access point or wireless router use WEP
security, enter the security code of the key
“No.1”to connect on your home network.
y
y
2
Preparation
Before setting the wireless network, you need
to:
-
connect the broadband internet to the
wireless home network.
An Access Point is a device that allows you
to connect to your home network wirelessly.
-
-
set the access point or wireless router.
note the SSID and security code of the
network.
4. Use W/S/A/Dto select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
1. Select [Connection Setting] option in the
[Setup] menu then press ENTER (b).
Note
,
2. Read the preparations for the network settings
and then press ENTER (b) while [Start] is
highlighted.
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/
A/Dand numerical buttons. If you make a
mistake while entering a number, press CLEAR
to clear the highlighted part.
5. Select [Next] and press ENTER (b) to apply
network settings.
If wired network is not connected to the unit, all
available networks are displayed on the screen.
3. Use W/Sto select a desired SSID of wireless
network and press ENTER (b).
Network connection status is displayed on the
screen.
6. Select [Close] and press ENTER (b) to complete
the network connection.
If you have security on your access point, you
need to input the security code as necessary.
20 Connecting
Advanced setting
If you want to set the network settings manually,
use W/Sto select [Advanced Setting] on the
[Network Setting] menu and press ENTER (b).
1. Use W/Sto select [Wireless] and press ENTER
(b).
2
[AP List] - Scans all available access points or
wireless routers within range and display them
as a list.
[Network name (SSID)] – Your access point
may not be broadcasting its network name
(SSID). Check your access point settings through
your computer and either set your access
point to broadcast SSID, or manually enter the
network name in [Network name(SSID)].
[PBC] – If your access point or wireless
router that supports the PBC (Push Button
Configuration) method, select this option and
press the Push Button on your access point
within 120 counts. You do not need to know the
network name (SSID) and security code of your
access point.
[PIN] – If your access point supports the PIN
Code configuration method based on WPS(Wi-
Fi Protected Setup), select this option and
note the code number on the screen. And
then, enter the PIN number on a setting menu
of your access point to connect. Refer to the
documentation for your network device.
2. Follow the instructions of each connection
method on the screen.
Note
,
To use PBC and PIN network connection,
security mode of your access point must be
set to OPEN or AES.
Connecting 21
subscriber agreement with your ISP, you may not
be able to use the internet connection feature
contained in this player or you may be limited
to the number of devices you can connect at
the same time. (If your ISP limits subscription to
one device, this player may not be allowed to
connect when a PC is already connected.)
Notes on network connection
Many network connection problems during
set up can often be fixed by re-setting the
router or modem. After connecting the player
to the home network, quickly power off and/
or disconnect the power cable of the home
network router or cable modem. Then power on
and/or connect the power cable again.
y
The use of a“Router”may not be allowed or its
usage may be limited depending on the policies
and restrictions of your ISP. For details, contact
your ISP directly.
y
y
Depending on the internet service provider (ISP),
the number of devices that can receive internet
service may be limited by the applicable terms
of service. For details, contact your ISP.
y
y
2
The wireless network operate at 2.4GHz
radio frequencies that are also used by other
household devices such as cordless telephone,
Bluetooth® devices, microwave oven, and can be
affected by interference from them.
Our company is not responsible for any
malfunction of the player and/or the internet
connection feature due to communication
errors/malfunctions associated with your
broadband internet connection, or other
connected equipment.
Turn off all unused network equipment in
your local home network. Some devices may
generate network traffic.
y
The features of BD-ROM discs made available
through the Internet Connection feature are not
created or provided by our company, and our
company is not responsible for their functionality
or continued availability. Some disc related
material available by the Internet Connection
may not be compatible with this player. If you
have questions about such content, please
contact the producer of the disc.
y
For better reception, place the player from the
access point as close as possible.
y
y
In some instances, placing the access point or
wireless router at least 0.45 m (1.5 ft.) above the
floor may improve the reception.
The reception quality over wireless depends on
many factors such as type of the access point,
distance between the player and access point,
and the location of the player.
y
y
Some internet content may require a higher
bandwidth connection.
y
y
Set your access point or wireless router to
Infrastructure mode. Ad-hoc mode is not
supported.
Even if the player is properly connected and
configured, some internet content may not
operate properly because of internet congestion,
the quality or bandwidth of your internet service,
or problems at the provider of the content.
Some internet connection operations may not
be possible due to certain restrictions set by the
Internet service provider (ISP) supplying your
broadband Internet connection.
y
Any fees charged by an ISP including, without
limitation, connection charges are your
responsibility.
y
y
A 10 Base-T or 100 Base-TX LAN port is required
for wired connection to this player. If your
internet service does not allow for such a
connection, you will not be able to connect the
player.
You must use a Router to use xDSL service.
y
y
A DSL modem is required to use DSL service and
a cable modem is required to use cable modem
service. Depending on the access method of and
22 Connecting
Note
,
USB Device
Connection
This player can play video, audio and photo files
contained in the USB device.
This player supports USB flash drive/
external HDD formatted in FAT32 and
NTFS when accessing files (music, photo,
movie). However, for BD-Live and Audio CD
recording, use the USB flash drive / external
HDD formatted in FAT32.
y
y
The USB device can be used for the local
storage for enjoying BD-Live discs with
Internet.
Playback content in the USB
device
1. Insert an USB device to the USB port until it fits
into place.
2
This unit can support up to 4 partitions of
the USB device.
y
y
y
Do not extract the USB device during
operation (play, etc.).
An USB device which requires additional
program installation when you have
connected it to a computer, is not
supported.
USB device: USB device that supports
USB1.1 and USB2.0.
y
y
Video, audio and photo files can be played.
For details of operations on each file, refer to
relevant pages.
When you connect the USB device on the HOME
menu, the player plays an audio file contained in
the USB storage device automatically. If the USB
storage device is containing various types of files, a
menu for the file type selection will appear.
Regular back up is recommended to
prevent data loss.
y
y
File loading may takes few minutes depending on
the number of content stored in the USB storage
device. Press ENTER (b) while [Cancel] is selected
to stop loading.
If you use an USB extension cable, USB HUB
or USB Multi-reader, the USB device may not
be recognized.
Some USB device may not work with this
unit.
y
y
y
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using A/D,
Digital camera and mobile phone are not
supported.
and press ENTER (b).
4. Select the [USB] option using W/S, and press
USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
ENTER (b).
5. Select a file using W/S/A/D, and press
PLAY or ENTER (b) to play the file.
6. Withdraw the USB device carefully.
System Setting 23
5. Use W/S/A/Dto select the IP mode
Initial Setup
When you turn on the unit for the first time, the
initial setup wizard appears on the screen. Set the
display language and network settings on the initial
setup wizard.
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
1. Press 1(POWER).
The initial setup wizard appears on the screen.
2. Use W/S/A/Dto select a display language
and press ENTER (b).
6. Select [Next] and press ENTER (b) to apply
network settings.
3
3. Read and prepare the preparations for the
network settings and then press ENTER (b)
while [Start] is highlighted.
Network connection status is displayed on the
screen.
For details on network settings, refer to
“Connecting to your Home Network”on page
7. Check all the settings that you have set in the
previous steps.
If wired network is connected, the network
connection setting will automatically be
finished.
4. All available networks are displayed on the
screen. Use W/Sto select [Wired Network]
or desired SSID of wireless network and press
ENTER (b).
Press ENTER (b) while [Finish] is highlighted
to finish the initial setup settings. If there is any
settings to be changed, use A/Dto select
[Previous] and press ENTER (b).
If you have security on your access point, you
need to input the security code as necessary.
24 System Setting
[DISPLAY] menu
Settings
TV Aspect Ratio
Select a TV aspect ratio option according to your TV
type.
Adjust the setup settings
You can change the settings of the player in the
[Setup] menu.
[4:3 Letter Box]
1. Press HOME (n).
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars
above and below the picture.
[4:3 Pan Scan]
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
2. Use A/Dto select the [Setup] and press ENTER
3
(b). The [Setup] menu appears.
[16:9 Original]
Select when a 16:9 wide TV is connected. The
4:3 picture is displayed with an original 4:3
aspect ratio, with black bars appearing at the
left and right sides.
[16:9 Full]
Select when a 16:9 wide TV is connected. The
4:3 picture is adjusted horizontally (in a linear
proportion) to fill the entire screen.
3. Use W/Sto select the first setup option, and
press Dto move to the second level.
Note
,
You cannot select [4:3 Letter Box] and
[4:3 Pan Scan] option when the resolution is
set to higher than 720p.
4. Use W/Sto select a second setup option, and
press ENTER (b) to move to the third level.
5. Use W/Sto select a desired setting, and press
ENTER (b) to confirm your selection.
System Setting 25
Resolution
HDMI Color Setting
Sets the output resolution of the HDMI video signal.
setting.
Select the type of output from the HDMI OUT jack.
For this setting, please refer to the manuals of your
display device.
[Auto]
[YCbCr]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
Select when connecting to a HDMI display
device.
[RGB]
Select when connecting to a DVI display
device.
[1080p]
Outputs 1080 lines of progressive video.
Home Menu Guide
[1080i]
This function allows you to display or delete the
guide bubble on the Home Menu. Set this option
to [On] for displaying guide.
Outputs 1080 lines of interlaced video.
3
[720p]
Outputs 720 lines of progressive video.
[480p]
Outputs 480 lines of progressive video.
1080p Display Mode
When the resolution is set to 1080p, select
[24 Hz] for smooth presentation of film material
(1080p/24 Hz) with a HDMI-equipped display
compatible with 1080p/24 Hz input.
Note
,
When you select [24 Hz], you may
experience some picture disturbance when
the video switches video and film material.
In this case, select [60 Hz].
y
y
Even when [1080p Display Mode] is set to
[24 Hz], if your TV is not compatible with
1080p/24 Hz, the actual frame frequency of
the video output will be 60 Hz to match the
video source format.
26 System Setting
[LANGUAGE] menu
[AUDIO] menu
Each disc has a variety of audio output options. Set
the player’s Audio options according to the type of
audio system you use.
Display Menu
Select a language for the [Setup] menu and on-
screen display.
Note
,
Since many factors affect the type of audio
output, see“Audio Output Specifications”on
page 59 for details.
Disc Menu/Disc Audio/
Disc Subtitle
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Digital Output
[Original]
[PCM Stereo] (HDMI only)
Refers to the original language in which the
disc was recorded.
Select if you connect this unit’s HDMI OUT jack
to a device with two-channel digital stereo
decoder.
3
[Other]
Press ENTER (b) to select another language.
Use number buttons then press ENTER (b)
to enter the corresponding 4-digit number
according to the language code list on page 56.
[PCM Multi-Ch] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with multi-channel digital decoder.
[DTS Re-Encode] (HDMI only)
[Off] (Disc Subtitle only)
Select if you connect this unit’s HDMI OUT jack
to a device with DTS decoder.
Turn off Subtitle.
Note
,
[BitStream] (HDMI only)
Depending on the disc, your language setting
may not work.
Select if you connect this unit’s HDMI OUT jack
to a device with LPCM, Dolby Digital, Dolby
Digital Plus, Dolby TrueHD, DTS and DTS-HD
decoder.
Note
,
When [Digital Output] option is set to [PCM
Multi-Ch], the audio may output as PCM
Stereo if the PCM Multi-Ch information is
not detected from HDMI device with EDID.
y
y
If the [Digital Output] option is set to [DTS
Re-Encode], the DTS Re-Encode audio is
outputted for BD-ROM discs with secondary
audio and the original audio is outputted
for the other discs (like [BitStream]).
System Setting 27
Sampling Freq.
DRC (Dynamic Range Control)
(Digital Audio Output)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound.
[48 kHz]
[Auto]
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz and 96 kHz
signal. When this choice is made, this unit
automatically converts any 192 kHz and 96 kHz
signals to 48 kHz so your system can decode
them.
The dynamic range of the Dolby TrueHD audio
output is specified by itself.
And the dynamic range of the Dolby Digital
and Dolby Digital Plus are operated as same as
the [On] mode.
[96 kHz]
[On]
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz signals. When
this choice is made, this unit automatically
converts any 192 kHz signals to 96 kHz so your
system can decode them.
Compress the dynamic range of the Dolby
Digital, Dolby Digital Plus or Dolby TrueHD
audio output.
3
[Off]
Turns off this function.
[192 kHz]
Note
Select this if your A/V Receiver or Amplifier is
capable of handling 192 kHz signals.
,
The DRC setting can be changed only when a
disc is not inserted or the unit is in complete
stop mode.
Check the documentation for your A/V Receiver or
Amplifier to verify its capabilities.
28 System Setting
DVD Rating
Blocks playback of rated DVD based on their
content. (Not all discs are rated.)
[LOCK] menu
The [LOCK] settings affect only Blu-ray Disc and
DVD playback.
To access the any features in [LOCK] settings, you
must enter the 4-digit security code you have
created.
If you have not entered a password yet, you are
prompted to do so. Enter a 4-digit password twice,
and press ENTER (b) to create a new password.
[Unlock]
If you select [Unlock], parental control is not
active and the disc plays in full.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
Password
You can create or change the password.
Blu-ray Disc Rating
Set an age limit of BD-ROM play. Use number
[None]
buttons to input an age limit for BD-ROM viewing.
3
Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[255]
[Change]
All BD-ROM can be played.
Enter the current password and press ENTER
(b). Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[0-254]
Prohibits play of BD-ROM with corresponding
ratings recorded on them.
If you forget your password
Note
,
If you forget your password, you can clear it using
the following steps:
The [Blu-ray Disc Rating] will be applied
only for the Blu-ray disc that containing the
advanced rating control.
y
y
1. Remove any disc that might be in the player.
2. Select [Password] option in the [Setup] menu.
For the region using MPAA rating level, refer
to the table below as an example.
3. Use number buttons to enter“210499”. The
password is cleared.
Blu-ray Disc Rating
MPAA Rating
Note
,
0
8
G
PG
If you make a mistake before pressing ENTER
(b), press CLEAR. Then input the correct
password.
13
17
18
255
PG-13
R
NC-17
Not restricted
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
System Setting 29
Netflix
[NETWORK] menu
The [NETWORK] settings are needed to use the
software update, BD-Live and online content
services.
[Netflix ESN]
Display its unique Netflix ESN (Electronic Serial
Number) that allows you to use the Netflix
streaming.
Connection Setting
[Deactivate Netflix]
If your home network environment is ready to
connect, the unit needs to be set up via wireless
or wired connection for network communication.
(See“Connecting to your Home Network”on page
Deactivates your player. To activate the Netflix
again, contact to the service provider.
Deactivate Vudu
You can deactivate your player from your Vudu
account. It is recommended that you do this if you
give your player to someone else who should not
share your Vudu account.
Connection Status
If you want to check the network status on this
player, select the [Connection Status] options and
press ENTER (b) to check whether a connection
to the network and the internet have been
established.
3
Device Name
You can make a network name using virtual
keyboard. This player will be recognised by the
name you are entering on your home network.
BD-LIVE connection
You can restrict Internet access when BD-Live
functions are used.
[Permitted]
Internet access is permitted for all BD-Live
content.
[Partially permitted]
Internet access is permitted only for BD-Live
content which have content owner certificates.
Internet access and AACS Online functions are
prohibited for all BD-Live content without a
certificate.
[Prohibited]
Internet access is prohibited for all BD-Live
content.
30 System Setting
Software
[OTHERS] menu
[Information]
Auto Power Off
Displays the current software version.
The screen saver appears when you leave the
player in Stop mode for about five minutes. If
you set this option to [On], the unit automatically
turns off within 20 minutes since the Screen Saver
is displayed. Set this option to [Off] to leave the
screen saver until the unit is operated by the user.
[Update]
You can update the software by connecting
the unit directly to the software update server
Disclaimer Notice
Press ENTER (b) to view the notice of Network
Service Disclaimer.
Initialize
[Factory Set]
You can reset the player to its original factory
settings.
3
[Blu-ray Storage Clear]
Initializes the BD-Live content from the
connected USB storage.
Note
,
If you reset the player to its original factory
settings using [Factory Set] option, you have to
set all the activation for the online services and
network settings again.
Operating 31
Playing a disc
General Playback
erto
1. Press B(OPEN/CLOSE), and place a disc on the
Using [HOME] menu
disc tray.
The home menu appears when you press HOME
(n). Use A/Dto select a category and press
ENTER (b).
2. Press B(OPEN/CLOSE) to close the disc tray.
For the most Audio CD, BD-ROM and
DVD-ROM discs, playback starts automatically.
3. Press HOME (n).
4. Select [Movie] or [Music] using A/D, and press
ENTER (b).
5. Select [Blu-ray Disc], [DVD], [VR] or [Audio]
option using W/S, and press ENTER (b).
Note
,
Playback functions described in this manual
are not always available in every files and
media. Some functions can be restricted
depending on many factors.
y
y
Depending on the BD-ROM titles, an USB
device connection may be needed for the
proper playback.
4
a
b
c
[Movie] - Plays video content.
[Photo] - Plays photo content.
[Music] - Plays audio content.
Unfinalized DVD-VR format discs may not
be played in this player.
y
y
[Premium] - Displays the Premium Home
screen.
Some DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
d
e
[Setup] - Adjusts the system settings.
Playing a file on disc/USB
device
yui
This player can play video, audio and photo files
contained in the disc or USB device.
1. Insert a data disc on the tray or connect an USB
device.
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using A/D,
and press ENTER (b).
4. Select [Data] or [USB] option using W/S, and
press ENTER (b).
5. Select a file using W/S/A/D, and press
d(PLAY) or ENTER (b) to play the file.
32 Operating
Enjoying BD-Live™
e
Basic operations for video and
audio content
BD-ROM supporting BD-Live that has a network
extension function allows you to enjoy more
functions such as downloading new movie trailers
by connecting this unit to the internet.
To stop playback
Press Z(STOP) during playback.
To pause playback
Press M(PAUSE) during playback.
Press d(PLAY) to resume playback.
1. Check the network connection and settings
2. Insert an USB storage device to the USB port on
the front panel.
To play frame-by-frame (Video)
Press M(PAUSE) during movie playback.
Press M(PAUSE) repeatedly to play Frame-by-Frame
playback.
An USB storage device is needed to download
bonus content.
3. Press HOME (n), and set the [BD-LIVE
connection] option on the [Setup] menu (page
To scan forward or backward
Press cor vto play fast forward or fast reverse
during playback.
Depending on a disc, the BD-Live function may
not be operated if [BD-LIVE connection] option
is set to [Partially Permitted].
You can change the various playback speeds by
pressing cor vrepeatedly.
4
4. Insert a BD-ROM with BD-Live.
The operations may differ depending on the
disc. Refer to the manual supplied with the disc.
To slow down the playing speed
While the playback is paused, press vrepeatedly
to play various speeds of slow motion.
Caution
>
Do not extract the connected USB device
while content is being downloaded or a Blu-
ray disc is still in the disc tray. Doing so may
damage the connected USB device and BD-
Live features may not operate properly with
the damaged USB device anymore. If the
connected USB device seems damaged from
such an action, you can format the connected
USB device from the PC and reuse it with this
player.
To skip to the next/previous
chapter/track/file
During playback, press Cor Vto go to the
next chapter/track/file or to return to the beginning
of the current chapter/track/file.
Press Ctwice briefly to step back to the previous
chapter/track/file.
In the file list menu of a server, there may have
many types of content in a folder together. In this
case, press Cor Vto go to the previous or
next content with same type.
Note
,
Some BD-Live content may be restrictively
accessed in some territories by content
provider’s own decision.
y
y
It may take up to several minutes to load
and start enjoying BD-Live content.
Operating 33
Basic operations for photo
content
Resume playback
eroyt
u
The unit records the point where you pressed the
Z(STOP) depending on the disc.
To play a slide show
Press d(PLAY) to start slide show.
If“MZ(Resume Stop)”appears on the screen briefly,
press d(PLAY) to resume playback (from the scene
point).
To stop a slide show
Press Z(STOP) during slide show.
If you press Z(STOP) twice or unload the disc,
“Z(Complete Stop)”appears on the screen. The unit
will clear the stopped point.
To pause a slide show
Press M(PAUSE) during slide show.
Press d(PLAY) to re-start the slide show.
Note
,
The resume point may be cleared when a
button is pressed (for example; 1(POWER),
B(OPEN/CLOSE), etc).
y
To skip to the next/previous photo
While viewing a photo in full screen, press Aor D
to go to the previous or next photo.
On BD-ROM discs with BD-J, the resume
playback function does not work.
y
y
Using the disc menu
ero
If you press Z(STOP) once during BD-ROM
interactive title playback, the unit will be in
Complete Stop mode .
4
To display the disc menu
The menu screen may be displayed first after
loading a disc which contains a menu. If you want
to display the disc menu during playback, press
DISC MENU.
Last scene memory
er
This unit memorizes the last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Use W/S/A/Dbuttons to navigate through
menu items.
To display the Pop-up menu
Some BD-ROM discs contain Pop-up menu that
appears during playback.
Note
,
Last Scene Memory function for a previous
disc is erased once a different disc is played.
y
y
y
y
Press TITLE/POP-UP during playback, and use W/
S/A/Dbuttons to navigate through menu
items.
This function may not work depending on
the disc.
On BD-ROM discs with BD-J, the last scene
memory function does not work.
This unit does not memorize settings of
a disc if you switch off the unit before
commencing to play it.
34 Operating
Repeating a specific portion
eroty
This player can repeat a portion you have selected.
Advanced Playback
Repeat playback
erotu
y
During playback, press REPEAT (h) repeatedly to
select a desired repeat mode.
1. During playback, press REPEAT (h) to select
[A-] at the beginning of the portion you wish to
repeat.
2. Press ENTER (b) at the end of the portion. Your
selected portion will be repeated continually.
3. To return to normal playback, press REPEAT
Blu-ray Disc / DVD / Video files
(h) repeatedly to select [Off].
jA- – Selected portion will be repeated continually.
Note
,
(Press ENTER (b) at the desired ending point.)
You cannot select a portion less than 3
seconds.
y
y
jChapter – The current chapter will be played
back repeatedly.
This function may not work on some disc or
title.
jTitle – The current title will be played back
repeatedly.
jAll – All the tracks or files will be played back
repeatedly.
Viewing content information
To return to normal playback, press REPEAT (h)
y
repeatedly to select [Off].
The player can display the content information.
Audio CDs/Audio files
1. Select a file using W/S/A/D.
;Track– The current track or file will be played
back repeatedly.
2. Press INFO/MENU (m) to display the option
menu.
:All – All the tracks or files will be played back
repeatedly.
3. Select the [Information] option using W/S,
and press ENTER (b).
l – The tracks or files will be played back in
random order.
The file information appears on the screen.
During movie playback, you can display the file
information by pressing TITLE/POP-UP.
l:All – All the tracks or files will be played
back repeatedly in random order.
Note
kA-B – Selected portion will be repeated
,
The information displayed on the screen
may not correct comparing actual content
information.
continually. (Audio CD only)
To return to normal playback, press CLEAR.
Note
,
If you press Vonce during Repeat
Chapter/Track playback, the repeat playback
cancels.
y
y
This function may not work on some disc or
title.
Operating 35
Changing content list view
Selecting a subtitle file
yui
On the [Movie], [Music] or [Photo] menu, you can
change the content list view.
y
If the subtitle file name is different from the video
file name, you need to select the subtitle file on the
[Movie] menu before playing the movie.
Method 1
Press red (R) colored button repeatedly.
1. Use W/S/A/Dto select the subtitle file you
wish to play in the [Movie] menu.
2. Press ENTER (b).
Press ENTER (b) again to deselect the subtitle
file. Selected subtitle file will be displayed when
you play the video file.
4
Note
,
If you press Z(STOP) during playback, the
y
y
subtitle selection is cancelled.
This function is not available for playing file
on a server via home network.
Changing the mode
yui
On the [Movie], [Music] or [Photo] menu, you can
change the mode.
Press yellow (Y) button repeatedly, the mode is
changed. (Movie : Photo : Music : Movie)
Note
,
Method 2
If you press Green (G) button on the [Movie],
[Music] or [Photo] menu, the related deivce list
will appear on the screen.
1. On the content list, press INFO/MENU (m) to
display the option menu.
2. Use W/Sto select the [View Change] option.
3. Press ENTER (b) to change the content list
view.
36 Operating
Options while viewing a photo
Listening to music during slide
show
i
You can use various options during viewing a
photo in full screen.
i
You can display photo files while listening to music
files.
1. While viewing a photo in full screen, press INFO/
MENU (m) to display the option menu.
1. While viewing a photo in full screen, press INFO/
2. Select an option using W/S.
MENU (m) to display the option menu.
2. Use W/Sto select [Music Select] option, and
press ENTER (b) to display the [Music Select]
menu.
3. Use W/Sto select a device, and press ENTER
(b).
Available device may differ depending on the
location of the current photo file.
Photo location
Disc, USB
Available Device
Disc, USB
DLNA server
DLNA server
a Current photo/Total number of photos
4
4. Use W/Sto select a file or a folder you wish to
– Use A/Dto view previous/next photo.
play.
b Slide Show – Press ENTER (b) to start or
pause slide show.
c Music Select – Select the background
music for the slide show (page 36).
d Music –Press ENTER (b) to start or pause
background music.
e Rotate – Press ENTER (b) to rotate the
photo clockwise.
Select gand press ENTER (b) to display the
upper directory.
f Zoom – Press ENTER (b) to display the
[Zoom] menu.
Note
g Effect – Use A/Dto select a transition
,
effect between photos in a slide show.
When selecting audio file from a server, folder
selection is not available. Only file selection is
available.
h Speed – Use A/Dto select a delaying
speed between photos in a slide show.
3. Press BACK(1) to exit the option menu.
5. Use Dto select [OK], and press ENTER (b) to
complete music selection.
Operating 37
Note
,
Playing a file on a network
server
yui
This player can play video, audio and photo files
located in a DLNA server through your home
network.
The file requirements are described on page
y
y
Thumbnails of files with unsupported
format will be displayed, but cannot be
played on this player.
The subtitle file name and video file name
have to be the same and located at the
same folder.
y
1. Check the network connection and settings
The playback and operating quality may be
affected by your home network condition.
y
y
y
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using A/D,
You may experience connection problems
depending on your server’s environment.
and press ENTER (b).
4. Select a DLNA media server on the list using
To set your PC as a DLNA server, install the
supplied Nero MediaHome 4 on your PC.
W/S, and press ENTER (b).
4
If you want to rescan available media server,
press the green (G) colored button.
5. Select a file using W/S/A/D, and press
ENTER (b) to play the file.
38 Operating
MAC OS X
1. Start up your computer, and insert the supplied
CD-ROM disc into your computer’s CD-ROM
drive.
Using Home Network
Server for PC
2. Browse the CD-ROM drive and open the
“MediaHome_4_Essentials_MAC”folder.
DLNA stands for Digital Living Network Alliance,
which allows users to access video, photo and
audio files stored in server and enjoy them on TV
via home networking.
3. Double-click the“Nero MediaHome.dmg”image
file. The Nero MediaHome window is opened.
Before connecting to PC to play a file , Nero
MediaHome 4 Essentials program should be
installed on your PC.
4. In the Nero MediaHome window, drag the Nero
MediaHome icon either to the Applications
folder within the window or to any other
desired location.
Installing Nero MediaHome 4
Essentials
5. You can now start the application by double-
clicking the Nero MediaHome icon in the
location you dragged it to.
Windows
Sharing files and folders
On your computer, you must share the folder
containing video, audio and/or photo content to
play them on this player.
Start up your computer, and insert the supplied CD-
ROM disc into your computer’s CD-ROM drive. An
installation wizard will walk you through the quick
and uncomplicated installation process. To install
Nero MediaHome 4 Essentials, proceed as follows:
4
This parts explains the procedure for selecting the
shared folders on your computer.
1. Close all Microsoft Windows programs and exit
any anti-virus software that may be running.
1. Double-click the“Nero MediaHome 4 Essentials”
icon.
2. Insert the supplied CD-ROM disc into your
computer’s CD-ROM drive.
2. Click [Network] icon on the left and define your
network name in the [Network name] field. The
Network name you enter will be recognized by
your player.
3. Click [Nero MediaHome 4 Essentials].
4. Click [Run] to start installation.
5. Click [Nero MediaHome 4 Essentials]. The
installation is prepared and the installation
wizard appears.
3. Click [Shares] icon on the left.
4. Click [Local Folders] tab on the [Shares] screen.
6. Click the [Next] button to display the serial
number input screen. Click [Next] to go to the
next step.
5. Click [Add] icon to open the [Browse Folder]
window.
6. Select the folder containing the files you want
to share. The selected folder is added to the list
of shared folders.
7. If you accept all conditions, click [I accept
the License Conditions] check box and click
[Next]. Installation is not possible without this
agreement.
7. Click [Start Server] icon to start the server.
8. Click [Typical] and click [Next]. The installation
process is started.
Note
,
If the shared folders or files are not displayed
on the player, click the folder on the [Local
Folders] tab and click [Rescan Folder] at the
[More] button.
y
y
9. If you want to take part in the anonymous
collection of data, select the check box and click
the [Next] button.
10. Click the [Exit] button to complete the
installation.
and software tools.
Operating 39
About Nero MediaHome 4
Essentials
Nero MediaHome 4 Essentials is a software for
sharing video, audio and photo files stored on your
computer to this unit as a DLNA-compatible digital
media server.
System requirements
Windows PC
Windows® XP (Service Pack 2 or higher), Windows
Vista® (no Service Pack required), Windows® 7
(no Service Pack required), Windows® XP Media
Center Edition 2005 (Service Pack 2 or higher),
Windows Server® 2003
y
Note
,
The Nero MediaHome 4 Essentials CD-
ROM is designed for PCs and should not
be inserted in this player or in any product
other than a PC.
y
y
y
y
Windows Vista® 64-bit edition (application runs
in 32-bit mode)
y
y
y
Windows® 7 64-bit edition (application runs in
32-bit mode)
The supplied Nero MediaHome 4 Essentials
CD-ROM is a customized software edition
only for sharing files and folders to this
player.
Hard drive space: 200 MB hard drive space for a
typical installation of Nero MediaHome stand-
alone
1.2 GHz Intel® Pentium® III or AMD
Sempron™ 2200+ processors
y
The supplied Nero MediaHome 4 Essentials
software does not support following
functions: Transcoding, Remote UI, TV
control, Internet services and Apple iTunes.
Memory: 256 MB RAM
y
y
Graphics card with at least 32 MB video memory,
minimum resolution of 800 x 600 pixels, and 16-
bit color settings
4
The supplied Nero MediaHome 4 Essentials
software can be downloaded at
Windows® Internet Explorer® 6.0 or higher
DirectX® 9.0c revision 30 (August 2006) or higher
Network environment: 100 Mb Ethernet, WLAN
-
download.php?id=nmhlgewin
y
y
y
-
download.php?id=nmhlgemac
This manual explains operations with
the English version of Nero MediaHome
4 Essentials as examples. Follow the
explanation referring to the actual
operations of your language version.
Macintosh
y
Mac OS X 10.5 (Leopard) or 10.6 (Snow Leopard)
y
y
y
Macintosh computer with an Intel x86 processor
Hard drive space: 200 MB hard drive space for a
typical installation of Nero MediaHome stand-
alone
Memory: 256 MB RAM
y
40 Operating
2. Select an option using W/S.
On-Screen Display
You can display and adjust various information and
settings about the content.
3. Use A/Dto adjust the selected option value.
4. Press BACK(1) to exit the on-screen display.
Note
,
If no button is pressed for a few seconds,
y
y
y
y
the on-screen display disappears.
Displaying content information
on-screen
A title number cannot be selected on some
discs.
eroy
Available items may differ depending on
discs or titles.
1. During playback, press INFO/MENU (m) to
show various playback information.
If an interactive Blu-ray Disc is playing back,
some setting information is displayed on
the screen but prohibited to be changed.
4
a Title – current title number/total number of
titles
b Chapter – current chapter number/total
number of chapters
c Time – elapsed playing time/total playback
time
d Audio – selected audio language or channel
e Subtitle – selected subtitle.
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
Operating 41
Playing from selected time
Hearing a different audio
eroy
1. Press INFO/MENU (m) during playback. The
time search box shows the elapsed playing
time.
eroy
1. During playback, press INFO/MENU (m) to
display the on-screen display.
2. Use W/Sto select the [Audio] option.
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
3. Use A/Dto select desired audio language,
audio track or audio channel.
Note
,
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds, enter“21020”.
Some discs allow you to change audio
selections only via the disc menu. In this
case, press TITLE/POP-UP or DISC MENU
button and choose the appropriate audio
from the selections on the disc menu.
y
Press A/Dto skip the playback 60 seconds
forward or backward.
3. Press ENTER (b) to start playback from selected
time.
Immediately after you have switched sound,
there may be a temporary discrepancy
between the display and actual sound.
y
y
Note
,
This function may not work on some disc or
y
y
On BD-ROM disc, the multi audio format
(5.1CH or 7.1CH) is displayed with [MultiCH]
in the on-screen display.
titles.
This function may not work depending on
the file type.
4
Watching from a different
angle
ero
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback.
Selecting a subtitle language
eroy
1. During playback, press INFO/MENU (m) to
display the on-screen display.
2. Use W/Sto select the [Subtitle] option.
3. Use A/Dto select desired subtitle language.
4. Press BACK(1) to exit the on-screen display.
1. During playback, press INFO/MENU (m) to
display the on-screen display.
Note
,
2. Use W/Sto select the [Angle] option.
3. Use A/Dto select desired angle.
Some discs allow you to change subtitle
selections only via the disc menu. If this is
the case, press TITLE/POP-UP or DISC MENU
button and choose the appropriate subtitle
from the selections on the disc menu.
y
4. Press BACK(1) to exit the on-screen display.
42 Operating
Changing the TV aspect ratio
Changing the picture mode
eoy
You can change the TV aspect ratio setting during
playback.
eroy
You can change the [Picture mode] option during
playback.
1. During playback, press INFO/MENU (m) to
1. During playback, press INFO/MENU (m) to
display the on-screen display.
display the on-screen display.
2. Use W/Sto select the [TV Aspect Ratio]
2. Use W/Sto select the [Picture Mode] option.
3. Use A/Dto select desired option.
option.
3. Use A/Dto select desired option.
4. Press BACK(1) to exit the on-screen display.
4. Press BACK(1) to exit the on-screen display.
Setting the [User setting] option
Note
,
1. During playback, press INFO/MENU (m) to
Even if you change the value of the [TV Aspect
Ratio] option in on-screen display, the [TV
Aspect Ratio] option in the [Setup] menu is
not changed.
display the on-screen display.
2. Use
W/S
to select the [Picture Mode] option.
3. Use A/Dto select the [User setting] option,
and press ENTER (b).
Changing subtitle code page
4
y
If the subtitle is displayed in broken letter, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press INFO/MENU (m) to
display the playback menu.
4. Use W/S/A/Dto adjust the [Picture Mode]
options.
2. Use W/Sto select the [Code Page] option.
Select [Default] option then press ENTER (b) to
reset the all video adjustments.
3. Use A/Dto select desired code option.
5. Use W/S/A/Dto select the [Close] option,
and press ENTER (b) to finish setting.
4. Press BACK(1) to exit the on-screen display.
Operating 43
Note
,
Audio CD Recording
You can record one desired track or all of the tracks
in Audio CD to an USB storage device.
The table below shows the average
recording time from an audio track with 4
minutes of playback time to an audio file
with 192 kbps as an example.
y
1. Insert an USB storage device to the USB port on
the front panel.
stop mode
1 min.
during playback
4 min.
2. Insert an Audio CD into the player.
The playback starts automatically.
Recording times in the table above are
approximate.
y
y
3. Press INFO/MENU (m) to display the option
menu.
Actual recording time for USB storage
device varies depending on the USB storage
device’s ability.
4. Select [CD Recording] option, and press ENTER
(b).
Make sure that there is minimum of 50 MB
free space is needed when recording into
the USB storage device.
y
5. Select a track you wish to copy on the menu,
and press ENTER (b).
Repeat this step to select tracks as many as you
can.
The length of the audio should be longer
than 20 seconds for the proper recording.
y
y
Selects all the tracks on an
Audio CD.
Do not turn off this player or extract the
connected USB storage device during Audio
CD recording.
4
Selects an encoding option
from the pop-up menu
(128kbps, 192kbps or 320kbps).
Caution
The recording or copying features on this
player are provided for your personal and
non-commercial use. The making of
unauthorized copies of copy-protected
material, including computer programs, files,
broadcasts and sound recordings, may be an
infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes. LG expressly disclaims
any responsibility for illegal distribution or
use of unauthorized content in commercial
purpose.
>
Cancels the recording and
returns to the previous screen.
6. Select [Start], and press ENTER (b).
7. Select a destination folder to be copied.
Be Responsible
Respect Copyrights
If you want to create a new folder, select [New
Folder] and press ENTER (b).
Enter a folder name using virtual keyboard, and
press ENTER (b) while [OK] is selected.
8. Select [OK], and press ENTER (b) to start Audio
CD recording.
If you want to stop in progressing Audio CD
recording, press ENTER (b) while [Cancel] is
highlighted.
9. A message appears when Audio CD recording is
completed. Press ENTER (b) to check the audio
file created in the destination folder.
44 Operating
Using the Premium
You can use various content services via Internet
with the Premium feature.
1. Check the network connection and settings
2. Press HOME (n).
3. Select the [Premium] using A/D, and press
ENTER (b).
4. Select an online service using W/S/A/D,
and press ENTER (b).
Note
,
4
For detailed information of each service,
contact to the content provider or visit
support link of the service.
y
y
The content of Premium services and
service related information, including user
interface, is subject to changes. Please refer
to the web site of each service for most up-
to-date information.
For the first time to access [Premium]
feature, current country setting appears. If
you want to change the country setting,
select [Edit] and press ENTER (b).
y
Troubleshooting 45
Troubleshooting
General
Symptom
Cause & Solution
The Power does not turned on.
Plug the power cord into the wall outlet securely.
y
The unit does not start
playback.
Insert a playable disc. (Check the disc type, color system, and regional
code.)
y
Place the disc with the playback side down.
Place the disc on the disc tray correctly inside the guide.
Clean the disc.
y
y
y
y
Cancel the Rating function or change the rating level.
The connected USB storage
device is not recognized.
Try using different USB cable, some USB cables may not support
enough current for normal USB operation.
y
y
y
y
If you use an USB extension cable or USB HUB, the USB devices may
not be recognized.
An USB device which requires additional program installation when
you have connected it to a computer is not supported.
This unit supports only USB Flash Drive and USB External HDD with
FAT32 or NTFS format.
5
The angle cannot be changed.
Multi-angles are not recorded on the DVD Video being played.
y
Cannot play video, photo or
audio files.
The files are not recorded in a format that the unit can play.
The unit does not support the codec of the video file.
y
y
The remote control does not
work properly.
The remote control is not pointed at the remote sensor of the unit.
The remote control is too far from the unit.
y
y
y
y
There is an obstacle in the path of the remote control and the unit.
The batteries in the remote control are exhausted.
The unit is plugged in, but the You can reset the unit as follows.
power will not turn on or off.
Unplug the power cord, wait at least five seconds, and then plug it in
y
again.
The unit is not operating
normally.
46 Troubleshooting
Network
Symptom
Cause & Solution
BD-Live feature does not work.
The connected USB storage may not have enough space. Connect
the USB storage with at least 1GB free space.
y
y
y
Ensure that the unit is correctly connected to the local area network
and can access the internet (page 16).
Your broadband speed may not fast enough to use the BD-Live
features. Contact your Internet Service Provider (ISP) and increase the
broadband speed is recommended.
The [BD-LIVE connection] option in the [Setup] menu is set to
[Prohibited]. Set the option to [Permitted].
y
y
Streaming video services (such
as YouTube™, etc.) are often
stopped or“buffer”during
playback.
Your broadband service speed may not be fast enough to stream
video services. Contact your Internet Service Provider (ISP) and
increase the broadband speed is recommended.
Media servers are not displayed
on the device list.
The firewall or anti-virus software on your media server is running.
Turn off the firewall or anti-virus software running on your media
server.
y
The player is not connected to the local area network that your media
server is connected.
y
y
Cannot connect the player to
the access point or wireless
LAN router.
The wireless communication may be interrupted from household
devices that are using radio frequencies. Move the player away from
them.
5
Access point is not displayed
on the“Access point name”list.
The access point or wireless LAN router may not broadcast its SSID.
Set your access point to broadcast its SSID through your computer.
y
y
Your network device such as access point may not set with available
frequency range and channel that this player can support.
Try setting the frequency range and channel on the network device
setting.
Troubleshooting 47
Picture
Symptom
Cause & Solution
There is no picture.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
y
Connect the video connection securely.
y
y
Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
Your TV may not support the resolution you have set on the player.
Change the resolution that your TV accepts.
y
y
The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears
You are playing a disc recorded in a colour system that is different
from your TV.
y
y
Set the resolution which your TV accepts.
Customer support
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit
Open source software notice
To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit
available to download with the source code.
5
48 Appendix
Setting up the remote to
control your TV
Controlling a TV with
the Supplied Remote
Control
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
You can control your TV using the buttons below.
1. While holding down 1(TV POWER) button,
and press the manufacturer code for your
TV with the numerical buttons (see the table
below).
Manufacturer
LG
Code Number
1(Default), 2
Zenith
1, 3, 4
1, 2
6, 7
8, 9
4
GoldStar
Samsung
Sony
By pressing
You can
1(TV POWER)
Turn the TV on or off.
Switch the TV’s input source
between the TV and other
input sources.
Hitachi
INPUT
2. Release the 1(TV POWER) button to complete
setting.
VOL +/–
Adjust the volume of the TV
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the battery
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
Note
,
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
6
Appendix 49
Software update
Network Software
Update
You can update the player using the latest software
to enhance the products operation and/or add
new features. You can update the software by
connecting the unit directly to the software update
server.
Network update notification
Note
,
From time to time, performance improvements
and/or additional features or services may be
made available to units that are connected to a
broadband home network. If there is new software
available and the unit is connected to a broadband
home network, the player will inform you about the
update as follows.
Before updating the software in your player,
remove any disc and USB Device from the
player.
y
Before updating the software in your player,
turn the player off and then turn it back on.
y
y
During the software update procedure,
do not turn off the player or disconnect
AC power, or do not press any button.
Option 1
1. The update menu will appear on the screen
when you turn off the player.
If you cancel the update, turn off the power
and turn it on for stable performance.
y
y
2. Use A/Dto select a desired option and then
This unit cannot be updated to previous
software version.
press ENTER (b).
1. Check the network connection and settings
2. Select [Software] option in the [Setup] menu
then press ENTER (b).
3. Select [Update] option, and press ENTER (b).
[OK]
Starts the software update.
[Cancel]
Exits the update menu and turns
the power off.
6
Option 2
If the software update is available from the update
server, the“Update”icon appears in the Home
menu. Press blue (B) colored button to start the
update procedure.
The player will check for the newest update.
Note
,
Pressing ENTER (b) while checking for the
y
y
update will end the process.
If there is no update available, the Message,
“No update is found.”appears. Press ENTER
(b) to return to the [Home Menu].
50 Appendix
4. If newer version exists, the message“Do you
want to download it?”appears.
5. Select [OK] to start update. (Selecting [Cancel]
will end the update.)
6. The player starts downloading the newest
update from the server. (Downloading will
takes several minutes depending on your home
network condition)
7. When downloading is completed, the message,
“Download is complete. Do you want to
update?”appears.
8. Select [OK] to start updating. (Selecting [Cancel]
will end the update and downloaded file will
not be re-usable. To update software the next
time, the software update procedure has to be
started from the beginning again.)
Caution
>
Do not turn off the power during the software
update.
Note
,
If the software includes the driver update, disc
tray may open during the process.
9. When update is completed, the power will be
turned automatically in a few seconds.
10. Turn the power back on. The system now
operates with the new version.
Note
,
6
The Software Update function may not
work properly depending on your internet
environment. In this case, you can obtain
the latest software from the authorized LG
Electronics Service Center then update your
player. Refer to“Customer support”on page
Appendix 51
Additional Information
File requirement
Video files
File
Location
File
Extension
Audio
Format
Codec Format
Subtitle
“.avi”, “.mpg”,
“.mpeg”, “.mkv”,
“.mp4”, “.asf”, “.m4v” AVC, MPEG2 PS,
XVID, MPEG1 SS, Dolby
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt), MicroDVD
(.sub/.txt), VobSub (.sub), SubViewer
H.264/MPEG-4
Digital,
DTS, MP3,
Disc,
USB
(DRM free), “.vob”,
“.3gp”, “.mov”, “.trp”,
“.m2t”, “.mpe”,
MPEG2 TS, VC-1
SM (WMV3)
WMA, AAC, 1.0 (.sub), SubViewer 2.0 (.sub/.txt),
AC3
TMPlayer (.txt), DVD Subtitle System
(.txt)
“.m1v”, “.m2v”, “.wm”
“.avi”, “.mpg”,
XVID, MPEG1 SS, Dolby
SubRip (.srt / .txt), SAMI (.smi),
“.mpeg”, “.mkv”,
“.mp4”, “.asf”, “.m4v” AVC, MPEG2 PS,
(DRM free), “.mov”, MPEG2 TS, VC-1
“.trp”, “.m2t”, “.mpe”,
“.m1v”, “.m2v”
H.264/MPEG-4
Digital,
DTS, MP3,
SubStation Alpha (.ssa/.txt), MicroDVD
(.sub/.txt), SubViewer 1.0 (.sub),
DLNA
WMA, AAC, SubViewer 2.0 (.sub/.txt), TMPlayer
AC3 (.txt), DVD Subtitle System (.txt)
SM (WMV3)
Audio files
File
Location
File
Extension
Sampling Frequency
Bitrate
Note
“mp3”, “.wma”,
“.wav”, “.m4a”
(DRM free),
“.flac”
within 32 - 48 kHz
(WMA), within 16 - 48
kHz (MP3)
within 32 - 192 kbps
(WMA), within 32 - 320 not supported on
kbps (MP3)
Some wav files are
Disc,
USB
6
this player.
“mp3”, “.wma”,
“.wav”, “.m4a”
(DRM free)
within 32 - 48 kHz
(WMA), within 16 - 48
kHz (MP3)
within 32 - 192 kbps
(WMA), within 32 - 320 not supported on
kbps (MP3)
Some wav files are
DLNA
this player.
Photo files
File
Location
File
Extension
Recommended
Size
Note
Disc,
USB,
DLNA
“.jpg”, “.jpeg”,
“.png”, “.gif”
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
Supplied bundle DLNA server for Macintosh edition has limitations in file compatibility, such as ASF, WMA
and WMV.
y
52 Appendix
Note
Note
,
,
The file name is limited to 180 characters.
y
y
A“avi”file which is encoded“WMV 9 codec”
is not supported.
y
y
Maximum files/Folder: Less than 2000 (total
number of files and folders)
This player supports UTF-8 files even it
contains Unicode subtitle content. This
player can not support the pure Unicode
subtitle files.
Depending on the size and number of the
files, it may take several minutes to read the
content on the media.
y
Depending on the types of file or ways of
recording, it may not play back.
y
y
File compatibility may differ depending on
the server.
y
y
A disc which was recorded by multi-session
on normal PC is not supported on this
player.
Because the compatibility on DLNA server
are tested on the bundle DLNA server
(Nero MediaHome 4 Essentials Windows
edition) environment, file requirements and
playback functions may differ depending on
media servers.
To be playback a video file, video file name
and Subtitle file name must be the same.
y
y
y
If video codec is MPEG2 TS or MPEG2 PS,
subtitle does not play back.
always compatible. There may have some
restrictions by file features. media server’s
ability.
y
y
y
The total playback time of audio file
indicated on the screen may not correct for
VBR files.
Playing video subtitle files are only available
on DLNA media server created by supplied
Nero MediaHome 4 Essentials software on
this player package.
Video / Audio codec compatibility may
differ depending on video file.
y
The files from removable media such as USB
drive, DVD-drive etc. on your media server
may not be shared properly.
AVCHD (Advanced Video
Codec High Definition)
This player can playback AVCHD format discs.
These discs are normally recorded and used in
camcorders.
This unit cannot support the ID3 Tag
embedded MP3 file.
y
y
y
The total playback time of audio file
indicated on the screen may not correct for
VBR files.
The AVCHD format is a high definition digital
video camera format.
y
y
6
HD video files contained on the CD/DVD or
USB 1.0/1.1 may not played properly.
Blu-ray Disc or USB 2.0 are recommended to
play back HD video files.
The MPEG-4 AVC/H.264 format is capable of
compressing images at higher efficiency than
that of the conventional image compressing
format.
y
y
y
This player supports H.264/MPEG-4 AVC
profile Main, High at Level 4.1. For a file
with higher level, the warning message will
appear on the screen.
This player can playback AVCHD discs using
“x.v.Color”format.
y
y
Some AVCHD format discs may not play
depending on the recording condition.
This player does not support files that are
AVCHD format discs need to be finalized.
y
y
2
recorded with GMC 1 or Qpel
.
*
*
“x.v.Color”offers a wider color range than normal
DVD camcorder discs.
*1 GMC – Global Motion Compensation
*2 Qpel – Quarter pixel
Appendix 53
About DLNA
Compatibility notes
This Player is a DLNA Certified digital media player
that can display and play movie, photo and music
content from your DLNA-compatible digital media
server (PC and Consumer Electronics).
Because BD-ROM is a new format, certain disc,
digital connection and other compatibility issues
are possible. If you experience compatibility
problems, please contact an authorized
Customer Service Center.
y
The Digital Living Network Alliance (DLNA) is a
cross-industry organization of consumer electronics,
computing industry and mobile device companies.
Digital Living provides consumers with easy sharing
of digital media through your home network.
This unit allows you to enjoy functions such
as picture-in-picture, secondary audio and
Virtual packages, etc., with BD-ROM supporting
BONUSVIEW (BD-ROM version 2 Profile 1 version
1.1). Secondary video and audio can be played
from a disc compatible with the picture-in-
picture function. For the playback method, refer
to the instructions in the disc.
y
The DLNA certification logo makes it easy
to find products that comply with the DLNA
Interoperability Guidelines. This unit complies with
DLNA Interoperability Guidelines v1.5.
Viewing high-definition content and up-
converting standard DVD content may require a
HDMI-capable input or HDCP-capable DVI input
on your display device.
y
When a PC running DLNA server software or
other DLNA compatible device is connected to
this player, some setting changes of software or
other devices may be required. Please refer to the
operating instructions for the software or device for
more information.
Some BD-ROM and DVD discs may restrict the
use of some operation commands or features.
y
y
Dolby TrueHD, Dolby Digital Plus and DTS-HD are
supported with maximum 7.1 channels if you
use HDMI connection for the audio output of the
unit.
Certain system requirements
For high definition video playback:
High definition display that has HDMI input jack.
BD-ROM disc with high definition content.
y
y
y
You can use an USB device to store some disc
related information, including downloaded
online content. The disc you are using will
control how long this information is retained.
y
HDMI or HDCP capable DVI input on your display
device is required for some content (as specified
by disc authors).
For Dolby® Digital Plus, Dolby TrueHD and DTS-HD
multi-channel audio playback:
6
An amplifier/receiver with a built-in (Dolby
Digital, Dolby Digital Plus, Dolby TrueHD, DTS or
DTS-HD) decoder.
y
Main, center, surround speakers and subwoofer as
necessary for chosen format.
54 Appendix
Audio Output Specifications
Jack/Setting
HDMI OUT
3
1
2
Source
BitStream
* *
PCM Stereo
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM Multi-Ch
PCM 2ch
DTS Re-encode
*
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
DTS
DTS
DTS
DTS
DTS
DTS
DTS
DTS
DTS
Dolby Digital
PCM 2ch
Dolby Digital Plus
Dolby TrueHD
DTS
PCM 2ch
PCM 2ch
DTS-HD
PCM 2ch
DTS-HD
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 5.1ch
PCM 7.1ch
*1 The secondary and interactive audio may not
be included in the output bitstream if [Digital
Output] option is set to [BitStream]. (Except
LPCM Codec : the output always include
interactive and secondary audio.)
The audio is outputted as PCM 48 kHz/16 bit for
MP3/WMA file and PCM 44.1kHz/16 bit for Audio
CD during playback.
y
y
You must select a digital audio output and
a maximum sampling frequency that your
Amplifier (or AV receiver) accepts using [Digital
Output] and [Sampling Freq.] options on the
*2 This player automatically selects the HDMI audio
according to the decoding capability of the
connected HDMI device even though [Digital
Output] option is set to [BitStream].
With digital audio connection (DIGITAL AUDIO
OUT or HDMI OUT), Disc Menu button sounds of
BD-ROM may not be heard if the [Digital Output]
option is set to [BitStream].
y
y
y
*3 If the [Digital Output] option is set to [DTS re-
encode], the audio output is limited to 48 kHz
and 5.1Ch. If the [Digital Output] option is set
to [DTS re-encode], the DTS Re-encode audio
is outputted for BD-ROM discs, and the original
audio is outputted for the other discs (like
[BitStream]).
If the audio format of the digital output does
not match the capabilities of your receiver, the
receiver will produce a strong, distorted sound
or no sound at all.
6
If the HDMI OUT jack is connected to your TV
with High Speed HDMI™ Cable and Dolby Digital
Plus/Dolby TrueHD is outputted from HDMI OUT
jack is limited to“PCM 2ch”.
y
Multi-channel Digital Surround Sound via digital
connection can only be obtained if your receiver
is equipped with a Digital Multi-channel decoder.
Appendix 55
Area Code List
Choose an area code from this list.
Area
Code Area
AF Fiji
Code Area
FJ Monaco
Code Area
Code
Afghanistan
Argentina
Australia
Austria
MC Singapore
SG
AR Finland
AU France
AT Germany
BE Great Britain
BT Greece
BO Greenland
BR Hong Kong
KH Hungary
CA India
FI Mongolia
FR Morocco
DE Nepal
MN Slovak Republic
MA Slovenia
NP South Africa
NL South Korea
AN Spain
SK
SI
ZA
KR
Belgium
Bhutan
GB Netherlands
GR Antilles
GL New Zealand
HK Nigeria
HU Norway
IN Oman
ES
Bolivia
NZ Sri Lanka
NG Sweden
NO Switzerland
OM Taiwan
LK
Brazil
SE
Cambodia
Canada
Chile
CH
TW
TH
TR
CL Indonesia
CN Israel
ID Pakistan
IL Panama
PK Thailand
PA Turkey
China
Colombia
Congo
CO Italy
IT Paraguay
JM Philippines
JP Poland
PY Uganda
UG
UA
US
UY
UZ
VN
ZW
CG Jamaica
CR Japan
PH Ukraine
Costa Rica
Croatia
PL United States
PT Uruguay
RO Uzbekistan
Vietnam
HR Kenya
KE Portugal
KW Romania
LY Russian
Czech Republic
Denmark
Ecuador
Egypt
CZ Kuwait
DK Libya
Federation
RU
EC Luxembourg
EG Malaysia
SV Maldives
ET Mexico
LU
Zimbabwe
Saudi Arabia
MY
SA
SN
Senegal
6
El Salvador
Ethiopia
MV
MX
56 Appendix
Language Code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
Language
Afar
Code Language
6565 French
6570 Frisian
Code Language
7082 Lithuanian
7089 Macedonian
7176 Malagasy
7565 Malay
Code Language
7684 Sindhi
7775 Singhalese
7771 Slovak
7783 Slovenian
7776 Spanish
7773 Sudanese
7782 Swahili
7779 Swedish
7778 Tagalog
7865 Tajik
Code
8368
8373
8375
8376
6983
8385
8387
8386
8476
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Afrikaans
Albanian
Amharic
Arabic
8381 Galician
6577 Georgian
6582 German
7289 Greek
6869 Malayalam
6976 Maori
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
6583 Greenlandic
6588 Guarani
6590 Gujarati
6665 Hausa
7576 Marathi
7178 Moldavian
7185 Mongolian
7265 Nauru
Basque
6985 Hebrew
6678 Hindi
7387 Nepali
7869 Tamil
Bengali; Bangla
Bhutani
Bihari
7273 Norwegian
7285 Oriya
7879 Telugu
7982 Thai
6890 Hungarian
6672 Icelandic
6682 Indonesian
6671 Interlingua
7789 Irish
7383 Panjabi
8065 Tonga
8083 Turkish
7065 Turkmen
8076 Twi
Breton
7378 Pashto, Pushto
7365 Persian
Bulgarian
Burmese
Byelorussian
Chinese
Croatian
Czech
7165 Polish
6669 Italian
7384 Portuguese
7465 Quechua
8084 Ukrainian
8185 Urdu
9072 Japanese
7282 Kannada
6783 Kashmiri
6865 Kazakh
7876 Kirghiz
6978 Korean
6979 Kurdish
6984 Laotian
7079 Latin
7578 Rhaeto-Romance 8277 Uzbek
6
7583 Rumanian
7575 Russian
7589 Samoan
7579 Sanskrit
7585 Scots Gaelic
7679 Serbian
7665 Serbo-Croatian
7686 Shona
8279 Vietnamese
Danish
8285 Volapük
8377 Welsh
8365 Wolof
7168 Xhosa
8382 Yiddish
8372 Yoruba
8378 Zulu
Dutch
English
Esperanto
Estonian
Faroese
Fiji
7074 Latvian, Lettish
7073 Lingala
Finnish
7678
Appendix 57
Trademarks and
Licenses
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0+Digital Out is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
Blu-ray Disc™, Blu-ray™, BD-Live™, BONUSVIEW™
and the logos are trademarks of the Blu-ray Disc
Association.
“DVD Logo”is a trademark of DVD Format/Logo
Licensing Corporation.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks
of the Digital Living Network Alliance.
Java is a trademark of Oracle and/or its affiliates.
The Wi-Fi CERTIFIED Logo is a certification mark
of the Wi-Fi Alliance.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
The Wi-Fi Protected Setup Mark is a trademark of
the Wi-Fi Alliance.
6
“x.v.Color”is a trademark of Sony Corporation.
“AVCHD”and the“AVCHD”logo are trademarks of
Panasonic Corporation and Sony Corporation.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
58 Appendix
Cinavia Notice
This product uses Cinavia technology to limit the
use of unauthorized copies of some commercially-
produced film and videos and their soundtracks.
When a prohibited use of an unauthorized copy is
detected, a message will be displayed and playback
or copying will be interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
request additional information about Cinavia by
mail, send a postcard with your mailing address
to: Cinavia Consumer Information Center, P.O. Box
86851, San Diego, CA, 92138, USA.
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other U.S.
and worldwide patents issued and pending as well
as copyright and trade secret protection for certain
aspects of such technology. Cinavia is a trademark
of Verance Corporation. Copyright 2004-2010
Verance Corporation. All rights reserved by Verance.
Reverse engineering or disassembly is prohibited.
6
Appendix 59
Specifications
General
Power requirements
AC adapter
DC 12 V 01 A
WA-12M12Fx
Dimensions (W x H x D)
Net Weight (Approx.)
Operating temperature
Operating humidity
Approx. 270 mm x 39 mm x 205 mm (10.6“ x 1.5“ x 8“)
0.95 kg (2.0 lbs)
5 °C to 35 °C (41 °F to 95 °F)
5 % to 90 %
Outputs
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
System
Laser
Semiconductor laser
wavelength
405 nm / 650 nm
Signal system
Standard NTSC color TV system
Ethernet jack x 1, 10BASE-T / 100BASE-TX
IEEE 802.11b/g/n (2.4 GHz band)
DC 5 V 0500 mA
LAN port
Wireless LAN (internal antenna)
Bus Power Supply (USB)
Design and specifications are subject to change without notice.
y
6
60 Appendix
Notes on discs
Maintenance
Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Handling the unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Storing discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Cleaning discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Keeping the exterior surfaces clean
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Do not use volatile liquids such as insecticide
spray near the unit.
y
y
y
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Maintaining the unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
6
Appendix 61
Important Information
Relating to Network
Services
All information, data, documents, communications,
downloads, files, text, images, photographs,
graphics, videos, webcasts, publications, tools,
resources, software, code, programs, applets,
widgets, applications, products and other content
(“Content”) and all services and offerings (“Services”)
provided or made available by or through any
third party (each a“Service Provider”) is the sole
responsibility of the Service Provider from whom it
originated.
The availability of and access to Content and
Services furnished by the Service Provider through
the LGE Device are subject to change at any time,
without prior notice, including, but not limited to
the suspension, removal or cessation of all or any
part of the Content or Services.
Should you have any inquiry or problem related
to the Content or Services, you may refer to the
Service Provider’s website for the most up-to-
date information. LGE is neither responsible nor
liable for customer service related to the Content
and Services. Any question or request for service
relating to the Content or Services should be made
directly to the respective Content and Service
Providers.
6
Please note that LGE is not responsible for any
Content or Services provided by the Service
Provider or any changes to, removal of, or cessation
of such Content or Services and does not warrant
or guaranty the availability of or access to such
Content or Services.
|