LG Electronics LG Lifes Good Car Video System W2343T User Manual

User’s Guide  
W2043T  
W2243T  
W2343T  
Make sure to read the Important Precautions before using the product.  
Keep the User's Guide(CD) in an accessible place for future reference.  
See the label attached on the product and give the information to your  
dealer when you ask for service.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place  
the display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen  
sink, laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release  
of heat generated during operation. If these openings are blocked, built-up heat  
can cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
Do not shock or scratch the front and sides of the screen with metallic objects.  
Otherwise, it may cause damage to the screen.  
Make sure the panel faces forward and hold it with both hands to move. If you  
drop the product, the damaged product can cause electric shock or fire. Contact  
an authorized the service center for repair.  
Avoid high temperatures and humidity.  
A2  
Important Precautions  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
When cleaning the product, unplug the power cord and scrub gently with a soft  
cloth to prevent scratching. Do not clean with a wet cloth or spray water or  
other liquids directly onto the product. An electric shock may occur. (Do not use  
chemicals such as benzene, paint thinners or alcohol)  
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;  
wipe in one direction only. Too much moisture may cause staining.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
A3  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand  
1.  
Place the monitor with its front facing downward on a soft cloth.  
2.  
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.  
Stand Body  
Stand Base  
3. Tie down the base lock to perpendicularity direction.  
4.  
Once assembled take the monitor up carefully and face  
the front side  
.
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
A4  
Connecting the Display  
Disassembling the stand  
1. Put a cushion or soft cloth on a flat  
2. Place the monitor face down on  
surface.  
the cushion or soft cloth.  
3. Change your lock on the product as it follows and turn it in the arrow direction.  
If you can't release the stand base even the locking rib is at a release position,  
Please push the indicated rib down and retry it.  
4. Pull out the stand to remove.  
A5  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Positioning your display  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range: -5˚~15˚  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing  
position, the forward tilt angle of the monitor should not exceed 5 degrees.  
A6  
Connecting the Display  
Using the Computer  
1. Make sure to turn off the computer and product. Connect the cable as below sketch map  
form  
to  
.
1
2
A
B
C
Connect DVI-D Cable  
Connect D-sub Cable (PC)  
Connect D-sub Cable (Mac)  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as shown.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard  
compliance for the product.  
Analog signal  
D-sub  
Digital signal  
DVI  
Power Cord  
Wall-outlet type  
Mac adapter  
For Apple Macintosh use, a separate plug  
adapter is needed to change the 15 pin high  
density (3 row) D-sub VGA connector on the  
supplied cable to a 15 pin 2 row connector.  
DVI-D (This feature is not available in all countries.)  
2. Press  
button on the front switch panel to turn the  
power on. When monitor power is turned on, the  
'Self Image Setting Function' is executed automatically.  
(Only Analog Mode)  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user  
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual  
input signals.  
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted  
screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve  
resolution.  
A7  
Connecting the Display  
Using the cable holder (This feature is not available in all models.)  
Cable holder  
1
2
3
4
A8  
Control Panel Functions  
Front Panel Controls  
Control  
Button  
Function  
Use this button to enter 4:3 IN WIDE, PHOTO EFFECT  
items, for more information, refer to page A17.  
Use this button to enter or exit from the On Screen Display.  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control settings, so  
that these settings are not inadvertently changed. To lock the  
OSD settings, press and hold the MENU button for several  
seconds. The message "OSD LOCKED" appears.  
You can unlock the OSD settings at any time by  
pushing the MENU button for several seconds. The  
message "OSD UNLOCKED" appears.  
A9  
Control Panel Functions  
Control  
Buttons  
Button  
Function  
Use these buttons to select or adjust functions in the On  
Screen Display.  
For more information, refer to page A18.  
(
)
Use this button to make either D-Sub or DVI  
connector active. This feature is used when two  
computers are connected to the display. The default  
setting is D-Sub.  
Button  
(SOURCE)  
Use this button to select an icon in the On Screen  
Display.  
AUTO/SET  
Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO/SET button prior to entering the On  
Screen Display(OSD). This will automatically adjust  
your display image to the ideal settings for the  
current screen resolution size (display mode).  
The best display mode is:  
W2043T : 1600 x 900  
W2243T/W2343T : 1920 x 1080  
Power Button  
Use this button to turn the display on or off.  
Power Indicator  
This Indicator lights up as red when the display is  
operating normally(On Mode). If the display is in  
Sleep Mode (Energy Saving), this indicator color  
changes to flicker.  
A10  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating parameters of  
the display is quick and easy with the On Screen Display Control system.  
A short example is given below to familiarize you with the use of the controls.  
The following section is an outline of the available adjustments and selections  
you can make using the OSD.  
NOTE  
Allow the display to stabilize for at least 30 minutes before making image adjustments.  
To make adjustments in the On Screen Display, follow these steps:  
Press the MENU Button, then the main menu of the OSD appears.  
To access a control, use the  
or  
Buttons. When the icon you want  
becomes highlighted, press the AUTO/SET Button.  
Use the  
/
Buttons to adjust the image to the desired level. Use the  
AUTO/SET Button to select other sub-menu items.  
Push the MENU Button once to return to the main menu to select another  
function. Push the MENU Button twice to exit from the OSD.  
A11  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
Main menu  
4:3 IN WIDE  
Sub-menu  
A
D
Reference  
To adjust the image size  
NORMAL  
GAUSSIAN BLUR  
SEPIA  
PHOTO  
EFFECT  
To adjust screen color mode  
MONOCHROME  
BRIGHTNESS  
CONTRAST  
GAMMA  
To adjust the brightness, contrast and  
gamma of the screen  
PICTURE  
COLOR  
sRGB  
6500K  
9300K  
PRESET  
To costomize the color of the screen  
To adjust the position of the screen  
RED  
GREEN  
BLUE  
HORIZONTAL  
VERTICAL  
CLOCK  
TRACKING  
To improve the clarity and stability of the  
screen  
PHASE  
SHARPNESS  
LANGUAGE  
HORIZONTAL  
VERTICAL  
OSD  
POSITION  
To costomize the screen status for a  
user's operating environment  
SETUP  
WHITE BALANCE  
POWER INDICATOR  
FACTORY RESET  
MOVIE  
INTERNET  
To select or customize desired image  
settings  
FLATRON  
F-ENGINE  
USER  
NORMAL  
DEMO  
: Adjustable  
A : Analog Input  
D : Digital Input  
NOTE  
The order of icons may differ depending on the model (A12~A18 ).  
A12  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Main Menu  
MENU  
SET  
: Exit  
: Adjust (Decrease/Increase)  
: Enter  
: Select another sub-menu  
: Restart to select sub-menu  
Button Tip  
Sub-menus  
Menu Name  
Icons  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
A13  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
PICTURE  
PICTURE  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
BRIGHTNESS  
CONTRAST  
GAMMA  
Set your own gamma value. : -50/0/50  
On the monitor, high gamma values  
display whitish images and low gamma  
values display high contrast images.  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
COLOR  
COLOR  
• sRGB: Set the screen color to fit the  
SRGB standard color  
PRESET  
specification.  
• 6500K: Slightly reddish white.  
• 9300K: Slightly bluish white.  
Set your own red color levels.  
Set your own green color levels.  
Set your own blue color levels.  
RED  
GREEN  
BLUE  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
A14  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
TRACKING  
TRACKING  
To move image left and right.  
To move image up and down.  
HORIZONTAL  
VERTICAL  
To minimize any vertical bars or  
stripes visible on the screen  
background.  
The horizontal screen size will also  
change.  
CLOCK  
PHASE  
To adjust the focus of the display.  
This item allows you to remove  
any horizontal noise and clear or  
sharpen the image of characters.  
MENU : Exit  
: Decrease  
To adjust the clearness of the  
screen.  
SHARPNESS  
: Increase  
SET : Select another sub-menu  
A15  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
SETUP  
SETUP  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
OSD  
POSITION  
To adjust position of the OSD window  
on the screen.  
If the output of the video card is different  
the required specifications, the color  
level may deteriorate due to video  
signal distortion. Using this function, the  
signal level is adjusted to fit into the  
standard output level of the video card  
in order to provide the optimal image.  
Activate this function when white and  
black colors are present in the screen.  
WHITE  
BALANCE  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
POWER  
INDICATOR  
MENU : Exit  
: Adjust  
: Adjust  
SET : Select another sub-menu  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
,
buttons to reset immediately.  
If this does not improve the screen image, restore the factory default settings.  
If necessary, perform the white balance function again. This function will be enabled only when  
the input signal is an analog signal.  
A16  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
monitor.  
button on the right bottom of the  
Main menu  
Sub menu  
Description  
4:3 IN WIDE  
To select the image size of the screen.  
WIDE  
4:3  
WIDE: Switch to full screen mode according to  
input image signal.  
4 : 3: Change the image signal ratio into 4:3.  
- NORMAL:  
The PhotoEffect function is disabled.  
PHOTO EFFECT  
- GAUSSIAN BLUR:  
This option is to add the effect to the screen  
that the dark and sharp image becomes  
brighter and more blurred.  
- SEPIA:  
This option changes the screen to be Sepia  
tone. The Sepia tone is brown color tone.  
- MONOCHROME:  
This option changed the screen to be Gray  
tone. The screen is displayed by white, black,  
gray.  
A17  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
the monitor.  
button on the right bottom of  
Menu Name  
Icons  
Sub-menu Name  
Main menu  
Sub menu  
Description  
MOVIE This feature lets you easily select the best desired  
INTERNET image condition optimized to the environment  
(ambient illumination, image types etc).  
MOVIE: For animation images in videos or movies  
INTERNET: For text images (Word processing etc.)  
MENU : Exit  
: Move  
USER User  
You can manually adjust ACE or RCM.  
You can save or restore the adjusted value even  
when using a different environment.  
To adjust the USER sub-menu  
function,press the AUTO/SET Button.  
...  
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.  
...  
RCM(Real Color Management): Selects the color mode.  
0
Not applied  
Green enhance  
1
2
Flesh tone  
3
Color Enhance  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
NORMAL This is under normal operating conditions.  
* Normal mode is when f-ENGINE is turned off.  
DEMO  
This is just for advertising to customer in the  
shops. It’s setting is same with Movie mode and  
screen is divided by half.  
A18  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power indicator  
Press the Power button.  
light on?  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
flickering?  
• Try to turn on the PC  
.
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see OSD  
LOCKEDwhen you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
OSD UNLOCKEDwill appear.  
A19  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
Important  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
If the recommended resolution (optimal resolution) is not selected, letters may  
be blurred and the screen may be dimmed, truncated or biased. Make sure to  
select the recommend resolution.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer  
.
A20  
Troubleshooting  
Display image is incorrect  
• Check if the signal cable is properly connected  
The screen color is  
and use a screwdriver to fasten if necessary.  
•Make sure the video card is properly inserted in  
the slot.  
mono or abnormal.  
•Set the color setting higher than 24 bits (true color)  
at Control Panel -Settings .  
The screen blinks.  
• Check if the screen is set to interlace mode and if  
yes,change it to the recommend resolution.  
Have you installed the display driver?  
Have you installed  
the display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette)that comes with your  
display.Or,you can also download the driver from  
Make sure to check if the video card supports  
Do you see an  
Plug&Play function.  
"Unrecognized monitor,  
Plug&Play (VESA DDC)  
monitor found"  
message?  
A21  
Specifications  
W2043T  
Display  
20.0 inches (50.8 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 50.8 cm  
0.2766*0.2766 mm pixel pitch  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Sync Input  
Digital : 30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Vertical Freq.  
Input Form  
Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1600 x 900 @60 Hz  
Digital : VESA 1600 x 900 @60 Hz  
VESA 1600 x 900 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B (Digital), DDC 2AB (Analog)  
:
38 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
On Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 48.36 cm / 19.04 inches 48.36 cm / 19.04 inches  
Height 37.68 cm / 14.83 inches 31.40 cm / 12.36 inches  
Depth 18.30 cm / 7.20 inches  
6.30 cm / 2.48 inches  
Net  
Tilt  
3.4 kg (7.56 lbs)  
-5˚~15˚  
Tilt Range  
AC 100-240V~ 50/60Hz 1.0 A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Power cord  
Attached( ), Detached ( O )  
Wall-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A22  
Specifications  
W2243T  
Display  
21.5 inches (54.6 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 54.6 cm  
0.248*0.248 mm pixel pitch  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Sync Input  
Digital : 30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Vertical Freq.  
Input Form  
Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1920 x 1080 @60 Hz  
Digital : VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B (Digital), DDC 2AB (Analog)  
:
40 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
On Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 51.64 cm / 20.33 inches 51.64 cm / 20.33 inches  
Height 39.60 cm / 15.59 inches 33.27 cm / 13.10 inches  
Depth 19.80 cm / 7.80 inches  
6.20 cm / 2.44 inches  
Net  
Tilt  
3.8 kg (8.49 lbs)  
-5˚~15˚  
Tilt Range  
Power Input  
AC 100-240V~ 50/60Hz 1.0A  
Environmental  
Conditions  
Operating Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Power cord  
Attached( ), Detached ( O )  
Wall-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A23  
Specifications  
W2343T  
Display  
23 inches (58.4 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 58.4 cm  
0.266*0.266 mm pixel pitch  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Sync Input  
Digital : 30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Vertical Freq.  
Input Form  
Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1920 x 1080 @60 Hz  
Digital : VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B (Digital), DDC 2AB (Analog)  
:
42 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
On Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 55.52 cm / 21.86 inches 55.52 cm / 21.86 inches  
Height 41.85 cm / 16.48 inches 35.77 cm / 14.08 inches  
Depth 19.80 cm / 7.80 inches  
6.30 cm / 2.48 inches  
Net  
Tilt  
4.4 kg (9.82 lbs)  
-5˚~15˚  
Tilt Range  
Power Input  
AC 100-240V~ 50/60Hz 1.0A  
Environmental  
Conditions  
Operating Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Power cord  
Attached( ), Detached ( O )  
Wall-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A24  
Specifications  
Preset Modes (Resolution)  
W2043T  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
60.000  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1600 x 900  
70  
60  
75  
60  
75  
60  
75  
75  
60  
3
4
5
6
7
8
*9  
* Recommend Mode  
W2243T/W2343T  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
720 x 400  
640 x 480  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
7
8
9
10  
11  
*12  
* Recommend Mode  
Indicator  
LED Color  
MODE  
Red  
Flicker  
Off  
On Mode  
Sleep Mode  
Off Mode  
A25  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Change your lock on the product as it follows and turn it in the arrow direction.  
3. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or wall mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more  
details, which is provided when Wall mount  
plate is purchased.  
Kensington Security Slot  
Connected to a locking cable that can be  
purchased separately at most computer stores.  
A26  
Digitally yours  

Rockford Fosgate PSD 1 User Manual
Precision Power A8SQ User Manual
Panasonic AG HVX200AP User Manual
Omega OSD30 User Manual
Olympus CAMEDIA C 220 ZOOM User Manual
Milwaukee 9572 User Manual
MB QUART Discus DKF 116 User Manual
Kenmore KWX 3V User Manual
JVC kds6060 User Manual
JVC GY HD200CHE User Manual