Kenwood KDC MPV8025 User Manual

KDC-MPV8025  
KDC-MP825  
CD-RECEIVER  
INSTRUCTION MANUAL  
Take the time to read through this instruction manual.  
Familiarity with installation and operation procedures will help  
you obtain the best performance from your new CD-receiver.  
For your records  
Record the serial number, found on the back of the unit, in the spaces  
designated on the warranty card, and in the space provided below.  
Refer to the model and serial numbers whenever you call upon your  
KENWOOD dealer for information or service on the product.  
Model KDC-MPV8025, KDC-MP825  
Serial number  
© B64-2743-00/01 (KV)  
2Warning  
2CAUTION  
Basic Operations of remote  
36  
Use of controls or adjustments or performance of  
procedures other than those specified herein may  
result in hazardous radiation exposure.  
In compliance with Federal Regulations, following  
are reproductions of labels on, or inside the product  
relating to laser product safety.  
Accessories/ Installation Procedure 38  
Connecting Wires to Terminals  
Installation  
39  
40  
42  
43  
46  
Removing the Unit  
Troubleshooting Guide  
Specifications  
KENWOOD CORPORATION  
2967-3, ISHIKAWA-CHO,  
HACHIOJI-SHI  
TOKYO, JAPAN  
KENWOOD CORP. CERTIFIES THIS EQUIPMENT  
CONFORMS TO DHHS REGULATIONS N0.21 CFR  
1040. 10, CHAPTER 1, SUBCHAPTER J.  
Location : Bottom Panel  
FCC WARNING  
This equipment may generate or use radio  
frequency energy. Changes or modifications to  
this equipment may cause harmful interference  
unless the modifications are expressly approved  
in the instruction manual. The user could lose  
the authority to operate this equipment if an  
unauthorized change or modification is made.  
NOTE  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment may cause harmful  
interference to radio communications, if it is  
not installed and used in accordance with the  
instructions. However, there is no guarantee  
that interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception, which  
can be determined by turning the equipment off  
and on, the user is encouraged to try to correct  
the interference by one or more of the following  
measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment  
and receiver.  
• Connect the equipment into an outlet on a  
circuit different from that to which the receiver is  
connected.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
English  
|
3
Safety precautions  
2WARNING  
2CAUTION  
To prevent injury or fire, take the  
following precautions:  
• Insert the unit all the way in until it is fully locked  
in place. Otherwise it may fall out of place when  
jolted.  
To prevent damage to the machine, take  
the following precautions:  
• Make sure to ground the unit to a negative 12V  
DC power supply.  
• Do not open the top or bottom covers of the unit.  
• When extending the ignition, battery, or ground  
wires, make sure to use automotive-grade wires  
or other wires with a 0.75mm² (AWG18) or more  
to prevent wire deterioration and damage to the  
wire coating.  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools)  
inside the unit.  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of  
water splashing.  
• Do not set the removed faceplate or the faceplate  
case in areas exposed to direct sunlight, excessive  
heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
• If the unit starts to emit smoke or strange smells,  
turn off the power immediately and consult your  
Kenwood dealer.  
• To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
• Make sure not to get your fingers caught between  
the faceplate and the unit.  
• Do not subject the faceplate to excessive shock,  
as it is a piece of precision equipment.  
• Be careful not to drop the unit or subject it to  
strong shock.  
The unit may break or crack because it contains  
glass parts.  
• Do not touch the liquid crystal fluid if the LCD  
is damaged or broken due to shock. The liquid  
crystal fluid may be dangerous to your health or  
even fatal.  
If the liquid crystal fluid from the LCD contacts  
your body or clothing, wash it off with soap  
immediately.  
• When replacing a fuse, only use a new one with  
the prescribed rating. Using a fuse with the wrong  
rating may cause your unit to malfunction.  
• To prevent a short circuit when replacing a fuse,  
first disconnect the wiring harness.  
• Do not place any object between the faceplate  
and the unit.  
• Do not apply excessive force to the moving  
faceplate. Doing so will cause damage or  
malfunction.  
• Do not apply excessive force to the open  
faceplate or place objects on it. Doing so will  
cause damage or breakdown.  
• Do not use your own screws. Use only the screws  
provided. If you use the wrong screws, you could  
damage the unit.  
|
4
English  
About CD players/disc changers  
connected to this unit  
KENWOOD disc changers/ CD players released in  
1998 or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood  
dealer for connectable models of disc changers/  
CD players.  
Note that any KENWOOD disc changers/ CD players  
released in 1997 or earlier and disc changers made  
by other makers cannot be connected to this unit.  
Unsupported connection may result in damage.  
Setting the "O-N" Switch to the "N" position for the  
applicable KENWOOD disc changers/ CD players.  
The functions that can be used and the information  
that can be displayed will differ depending on the  
models being connected.  
NOTE  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when  
the Reset button is pressed. If the unit still fails to  
operate properly after the Reset button has been  
pressed, contact your local KENWOOD dealer for  
assistance.  
• Press the reset button if the disc auto changer fails  
to operate correctly. Normal operation should be  
restored.  
You can damage both your unit and the CD changer if  
you connect them incorrectly.  
Reset button  
• We recommend the use of 'Security Code' (page  
32) to prevent theft.  
• Characters in the LCD may become difficult to  
read in temperatures below 41 ˚F (5 ˚C).  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on  
the display on the actual equipment, and some  
of the illustrations on the display may represent  
something impossible in actual operation.  
Do Not Load 3-in. CDs in the CD slot  
If you try to load a 3 in. CD with its adapter into the  
unit, the adapter might separate from the CD and  
damage the unit.  
Lens Fogging  
Right after you turn on the car heater in cold  
weather, dew or condensation may form on  
the lens in the CD player of the unit. Called lens  
fogging, CDs may be impossible to play. In such  
a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does  
not operate normally after a while, consult your  
Kenwood dealer.  
English  
|
5
Notes  
Cleaning the Unit  
Sirius Satellite radio tuner  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off  
with a cloth moistened with neutral cleaner, then  
wipe neutral detergent off.  
Refer to the Sirius tuner control features of this  
manual for the operation method of Sirius Satellite  
radio tuner KTC-SR901/SR902 (optional accessory)  
when connected.  
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth  
or using a volatile liquid such as thinner or alcohol may  
scratch the surface or erases characters.  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get dirty,  
wipe them with a dry, soft cloth.  
Cleaning the CD Slot  
As dust tends to accumulate in the CD slot, clean it  
every once in a while. Your CDs can get scratched if  
you put them in a dusty CD slot.  
NOTE  
This Class B digital apparatus complies with  
Canadian ICES-003.  
|
6
English  
About CDs  
Handling CDs  
• Don’t touch the recording surface of the CD.  
Removing CDs  
When removing CDs from this unit pull them out  
horizontally.  
CDs that can’t be used  
• CDs that aren’t round can’t be used.  
• CD-R and CD-RW are easier to damage than a  
normal music CD. Use a CD-R or a CD-RW after  
reading the caution items on the package etc.  
• Don’t stick tape etc. on the CD.  
Also, don’t use a CD with tape stuck on it.  
• CDs with coloring on the recording surface or that  
are dirty can’t be used.  
• This unit can only play the CDs with  
When using a new CD  
If the CD center hole or outside rim has burrs, use it  
after removing them with a ball pen etc.  
.
It may not correctly play discs which do not have  
the mark.  
• A CD-R or CD-RW that hasn’t been finalized can’t  
be played. (For the finalization process refer to  
your CD-R/CD-RW writing software, and your CD-  
R/CD-RW recorder instruction manual.)  
Burrs  
Burrs  
CD storage  
• Don’t place them in direct sunlight (On the seat  
or dashboard etc.) and where the temperature is  
high.  
• Store CDs in their cases.  
CD accessories  
Don’t use disc type accessories.  
CD cleaning  
Clean from the center of the disc and move  
outward.  
English  
|
7
Notes on playing MP3/WMA  
Note, however, that the MP3/WMA recording  
media and formats acceptable are limited. When  
writing MP3/WMA, pay attention to the following  
restrictions.  
Play mode may not be possible when portions of the  
functions of Windows Media Player 9 or higher are used.  
Entering ID3 tag  
The Displayable ID3 tag is ID3 version 1.x.  
For the character code, refer to the List of Codes.  
Acceptable media  
The MP3/WMA recording media acceptable to this  
unit are CD-ROM, CD-R, and CD-RW.  
When using CD-RW, do full format not quick format  
to prevent malfunction.  
Acceptable medium formats  
The following formats are available for the media  
used in this unit. The maximum number of  
characters used for file and folder name including  
the delimiter (".") and three-character extension are  
indicated in parentheses.  
• ISO 9660 Level 1 (12 characters)  
• ISO 9660 Level 2 (31 characters)  
• Joliet (64 character; Up to 32 characters are  
displayed)  
• Romeo (128 character; Up to 64 characters are  
displayed)  
• Long file name (200 characters; Up to 64  
characters are displayed)  
• Maximum number of characters for folder name:  
Entering file and folder names  
The code list characters are the only file names and  
folder names that can be entered and displayed.  
If you use any other character for entry, the file and  
folder names are not displayed correctly. They may  
neither be displayed correctly depending on the CD  
writer used.  
The unit recognizes and plays only those MP3/WMA  
which have the MP3/WMA extension (.MP3/.WMA).  
64 (Joliet; Up to 32 characters are displayed)  
For a list of available characters, see the instruction  
manual of the writing software and the section  
Entering file and folder names below.  
The media reproducible on this unit has the  
following limitations:  
• Maximum number of directory levels: 8  
• Maximum number of files per folder: 255  
• Maximum number of folders: 50  
A file with a name entered with characters not on the  
code list may not play correctly.  
Writing files into a medium  
When a medium containing MP3/WMA data is  
loaded, the unit checks all the data on the medium.  
If the medium contains a lot of folders or non-MP3/  
WMA files, therefore, it takes a long time until the  
unit starts playing MP3/WMA.  
• Maximum number of files and folders: 512  
MP3/WMA written in the formats other than the  
above may not be successfully played and their file  
names or folder names are not properly displayed.  
In addition, it may take time for the unit to move  
to the next MP3/WMA file or a File Search or Folder  
Search may not be performed smoothly.  
Settings for your MP3/WMA encoder and  
CD writer  
Do the following setting when compressing  
audio data in MP3/WMA data with the MP3/WMA  
encoder.  
• Transfer bit rate: MP3: 8 —320 kbps  
WMA: 48 —192 kbps  
• Sampling frequency  
Loading such a medium may produce loud noise to  
damage the speakers.  
Do no attempt to play a medium containing a non-MP3/  
WMA file with the MP3/WMA extension.  
The unit mistakes non-MP3/WMA files for MP3/WMA data  
as long as they have the MP3/WMA extension.  
Do not attempt to play a medium containing non MP3/  
WMA.  
MP3: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz  
WMA: 32, 44.1, 48 kHz  
When you use your CD writer to record MP3/WMA  
up to the maximum disc capacity, disable additional  
writing. For recording on an empty disc up to the  
maximum capacity at once, check Disc at Once.  
|
8
English  
MP3/WMA playing order  
When selected for play, Folder Search, File Search,  
or for Folder Select, files and folders are accessed  
in the order in which they were written by the CD  
writer.  
Because of this, the order in which they are  
expected to be played may not match the order in  
which they are actually played. You may be able to  
set the order in which MP3/WMA are to be played  
by writing them onto a medium such as a CD-R  
with their file names beginning with play sequence  
numbers such as "01" to "99", depending on your  
CD writer.  
When a File Search is executed with file ¡$  
being played ...  
Operation of  
(Current file: ¡$)  
the button  
4 Button  
Beginning of file ¡$ ¡#  
¢ Button  
¡% ¡&  
When a Folder Search is executed with file ¡$  
being played ...  
Operation of  
(Current folder: 4)  
the button  
For example, a medium with the following folder/  
file hierarchy is subject to Folder Search, File Search,  
or Folder Select as shown below.  
AM Button  
FM Button  
3 2 1 8 ...  
5 6 7 8 1 ...  
Example of a mediums folder/file hierarchy  
Folder  
When Folder Select is selected with file ¡$  
being played to move from folder to folder ...  
File  
Operation of  
Root  
(Current folder: 4)  
the button  
4 Button  
¢ Button  
AM Button  
FM Button  
3
6
2
5
Level 1  
Level 3  
Level 5  
Level 2  
Level 4  
English  
|
9
Notes on Multi-function Key System  
Multi-function Key System serves to control various  
functions with the [2] — [5] buttons.  
The basic operation of the Multi-function Key  
System is described below.  
Real operational example of the Multi-  
function Key System  
Example: Turning ON/OFF the Random Play during  
CD play.  
1. Show the function display of the Random Play.  
If "RDM" is not shown in the display, press the  
[NEXT] button to switch the sections until the  
"RDM" function display is shown above the [3]  
button.  
Whats the Multi-function Key System?  
This unit is equipped with the Multi-function Key  
System that enables the operation of multiple  
functions with one button.  
2. Turn ON/OFF the Random Play.  
Press the [3] button.  
Each time the [3] button under the "RDM"  
function display is pressed the Random Play is  
turned ON/OFF.  
For example, you can enter the Display Control  
Mode or turn ON/OFF the Random Play by pressing  
the [3] button during CD play.  
Setting each function  
The function display will show the controllable  
function of the [2] — [5] button above the button.  
Pressing the [2] — [5] button below the desired  
function enables the setting of the function.  
EXT  
Displaying the desired function  
If five or more functions are available to be set with  
the [2] — [5] button, they are divided into multiple  
function groups (referred to as sections in this  
manual) for registration.  
Press the [NEXT] button to switch the sections.  
If the display of the desired function is not shown,  
press the [NEXT] button 1 to 3 times to switch the  
sections until the wanted function display is shown.  
Example: Function display of CD & External disc  
source  
"MRDM", "H-F", "SYNC" or "DISP" are displayed when an  
optional accessory is connected.  
|
10  
English  
General features  
ATT  
1 – 6  
NEXT  
SRC  
VOL  
Q
NAME.S AM/  
SW  
FM  
4
¢
ATT indicator  
indicator  
Function display  
Power  
Hiding the Control Panel  
Prevents tampering with the unit while your car is  
being serviced etc.  
Turning ON the Power  
Turn the vehicle ignition ON.  
The panel appears.  
Hiding the control panel  
Press the [SRC] button for at least 1 second.  
When the time set in 'OFF Wait Time Setting'  
(page 33) lapses, the panel is hidden and the  
power turns OFF.  
Turing OFF the Power  
Turn the vehicle ignition OFF or press the  
[SRC] button for at least 1 second.  
The panel hides.  
Showing the control panel  
Press the left part at the lower side of the  
panel.  
Do not apply force to the panel during operation. It  
can cause damage.  
The panel is opened to enable the operation.  
English  
|
11  
General features  
Selecting the Source  
Top 40  
Jazz  
"Top40"  
"Jazz"  
Press the [SRC] button.  
Source required  
Display  
"SIRIUS"  
User memory: The values set on the 'Audio Control'  
(page 12).  
Each setting value is changed with the 'Speaker  
Setting' (page 14).  
SIRIUS tuner (Optional accessory)  
Tuner or HD Radio (Optional accessory)  
CD  
External disc (Optional accessory)  
Auxiliary input (Optional accessory)  
Auxiliary input (KDC-MPV8025 only)  
Standby (Illumination only mode)  
"TUNER" or“HD RADIO”  
"CD"  
"CD CH"/"CD2"  
"AUX EXT"  
"AUX"  
First, select the speaker type with the Speaker setting.  
"STANDBY"  
Audio Control  
1 Select the source for adjustment  
Press the [SRC] button.  
Volume  
Increasing Volume  
Turn the [VOL] knob clockwise.  
2 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "AUD" is  
displayed above the [2] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Decreasing Volume  
Turn the [VOL] knob counterclockwise.  
3 Enter Audio Control mode  
Press the [2] ("AUD") button.  
Attenuator  
Turning the volume down quickly.  
4 Select the Adjustment item section  
Press the [NEXT] button.  
Press the [ATT] button.  
Each time the button is pressed the Attenuator  
turns ON or OFF.  
When it’s ON, the "ATT" indicator blinks.  
Repeatedly press the button until the desired  
Adjustment item is displayed above the [2] — [5]  
button.  
1st section  
Adjustment Item  
Bass  
Middle  
Treble  
Subwoofer*  
Button  
[2]  
[3]  
[4]  
[5]  
Display  
"BASS"  
"MID"  
"TRE"  
System Q  
You can recall the best sound setting preset for  
different types of music.  
"SW"  
1 Select the source to set  
Press the [SRC] button.  
2nd section  
Adjustment Item  
High Pass Filter  
Low Pass Filter*  
Loudness  
Button  
[2]  
[3]  
[4]  
[5]  
Display  
"HPF"  
"LPF"  
"LOUD"  
"BL/F"  
2 Select the Sound type  
Press the [Q] button.  
Each time the button is pressed the sound  
setting switches.  
Balance & Fader  
Sound setting  
Flat  
User memory  
Rock  
Pops  
Easy  
Display  
"Flat"  
"User"  
"Rock"  
"Pops"  
"Easy"  
3rd section  
Adjustment Item  
Volume offset  
Button  
[2]  
Display  
"VOFF"  
|
12  
English  
2nd section  
[2] button  
5 Select the Audio Control item for  
adjustment  
Press the [2] — [5] button.  
Each time the [2] — [5] button is pressed the  
adjustable audio items are switched among  
ranges of all stage section’s tables on the  
following pages.  
Adjustment Item  
Front/Rear High Pass Filter "HPF"  
Display  
Range  
THRU/100/125/170 Hz  
[3] button  
Adjustment Item  
Subwoofer Low Pass Filter "LPF SW"  
Display  
Range  
50/80/120/THRU Hz  
6 Adjust the Audio Control item  
Press the [4] or [¢] button.  
Each time the button is pressed the setting  
switches as shown below.  
[4] button  
Adjustment Item  
Display  
Range  
Loudness  
"LOUD"  
ON/OFF  
The Adjustment item can also be controlled by the  
rotary volume knob. Refer to 'Rotary Volume knob  
operation mode select'(page 14).  
[5] button  
Adjustment Item  
Balance  
Fader  
Display  
"Balance" L 15 — R 15  
"Fader" R 15 — F 15  
Range  
7 Exit Audio Control mode  
Press the [6] button.  
The loudness setting can also be adjusted by pressing  
the [4] button.  
*This mode is available only when 'Subwoofer Output'  
(page 14) is ON.  
When the Dual Zone System is ON, the setting for the  
High Pass Filter is nullified.  
1st section  
3rd section  
[2] button  
[2] button  
Adjustment Item  
Bass level  
Display  
"Bass"  
Range  
–8 — +8  
Adjustment Item  
Volume offset  
Display  
"V-Offset" –8 — 0  
Range  
[3] button  
Adjustment Item  
Middle level  
Display  
"Middle"  
Range  
–8 — +8  
Volume offset: Each source’s volume can be set as a  
difference from the basic volume.  
[4] button  
Adjustment Item  
Display  
Range  
Treble level  
"Treble"  
–8 — +8  
[5] button  
Adjustment Item  
Display  
Range  
Subwoofer level  
"SW Level" –15 — +15  
English  
|
13  
General features  
Rotary Volume knob operation  
mode select  
3 Select the Speaker type  
Press the [2] — [5] button.  
Each time the button is pressed the setting  
switches as shown below.  
The rotary volume knob can be used for volume  
adjustment and various function setups.  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Button Display  
Available setup functions  
The rotary volume knob can be used for the  
following setup:  
[2]  
[3]  
[4]  
[5]  
"OFF"  
"5/4"  
"69/6"  
"OEM"  
• Menu system : Item selection  
• Audio Control : Adjustment of setup value  
• Display control : Display switching  
• Station/Disc Naming (SNPS/DNPS) : Character  
selection  
4 Exit Speaker Setting mode  
Press the [Q] button.  
• Folder select : Folder search  
Subwoofer Output  
You can select the Rotary Volume Operation mode  
only when the " " indicator is displayed above the [1]  
button during any function setup.  
Turning the Subwoofer output ON or OFF.  
Press the [SW] button for at least 1 second.  
Each time the button is pressed Subwoofer  
output switches ON or OFF.  
When the " " indicator is OFF, you cannot use the  
rotary volume control for function setup and sound  
level adjustment.  
When it’s ON, "Sub-W ON" is displayed.  
To use the rotary volume knob:  
1 Turn the rotary volume operation ON  
See the 'Rotary volume operation select' (35  
page) and select "Rotary ON".  
You can control this function when 'Switching preout'  
(page 34) is set to "SWPRE Sub-W".  
2 Selecting the Rotary Volume Operation  
mode  
Press the [1] button.  
When it’s ON, the " " indicator blinks.  
Function of the KDC-MPV8025  
In SIRIUS Tuner, External disc, or Auxiliary input  
source  
3 Setting the function  
Rotate the Rotary Volume knob.  
Dual Zone System  
Makes the sound different for the front channel  
and rear channel.  
Output the Internal source sound from either one  
of the front or rear channels, and the sound of  
other source from the Dual zone channel.  
4 Terminates the function setup using the  
rotary volume knob  
Press the [1] button.  
1 Select the source  
Press the [SRC] button.  
Speaker Setting  
Select the source sound to be output from the  
Dual zone channel.  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type.  
2 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "2-ZN" is  
displayed above the [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Speaker Setting mode  
Press the [Q] button.  
|
14  
English  
3 Enter the Dual Zone System Control mode  
Press the [5] ("2-ZN") button.  
Display Mode Switching  
Switching the display mode.  
4 Select the item for adjustment  
Press the desired [2] — [3] button.  
Each time the button is pressed the items that  
can be adjusted switch as shown below.  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "DISP" is  
displayed above the [3] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Adjustment Item Button Display  
Range  
Dual Zone System  
Dual Zone System  
Front & Rear  
[2]  
[3]  
"ON"/"OFF"  
"F – R"  
ON/OFF  
Front/Rear  
2 Enter display control mode  
Press the [3] ("DISP") button.  
3 Select the display mode  
Dual Zone System Rear:  
The front is this unit’s internal source, and the rear is  
selected source sound.  
Press the [2] ("MODE") button.  
Each time the button is pressed the display  
mode switches as shown below.  
Dual Zone System Front:  
The rear is this unit’s internal source, and the front is  
selected source sound.  
Display  
Display Mode  
Demonstration.  
Normal display type.  
Silent display type.  
"Display C"  
"Display A"  
"Display B"  
5 Exit the Dual Zone System Control mode  
Press the [6] button.  
6 Select the source  
Press the [SRC] button.  
4 Exit display control mode  
Press the [6] button.  
Select the source sound to be output from the  
internal source channel.  
The Dual Zone System can be used with the sources  
shown below.  
- Internal auxiliary input  
- KCA-S210A  
- CA-C1AX  
- External disc changer/ player  
- SIRIUS satellite radio tuner  
While Dual Zone System is ON, the setting of Dual  
Zone System Front or Rear is disabled.  
Set Dual Zone System Front or Rear first, and then set  
the Dual Zone System to ON.  
When the Dual Zone System is ON, there is no Dual  
zone channel audio control or other effect.  
When you use the Dual Zone System by selecting the  
optional accessory source for the output of the Dual  
zone channel, you cannot select another optional  
accessory source as the source for the Internal source  
channel.  
When you set the Dual zone system to ON while the  
sub woofer preout is switched ON, the sound of the  
sub woofer preout isn’t output.  
The Dual Zone System cannot be used if a DAB  
control unit is connected.  
English  
|
15  
General features  
In Standby  
Text Display Switching  
Information  
Display  
"STANDBY"  
"Clock"  
Switching the text display.  
1 Select the key function section  
Press the [NEXT] button.  
Clock  
Repeatedly press the button until "DISP" is  
displayed above the [3] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
In SIRIUS tuner source  
Information  
Channel Name  
Song Title  
Display  
"Channel Name"  
"Song Title"  
"Artist Name"  
"Composer"  
"Category"  
"Channel No"  
"Clock"  
Artist Name  
2 Enter display control mode  
Composer name  
Category Name  
Band & Channel Number  
Clock  
Press the [3] ("DISP") button.  
3 Select the text  
Press the [3] ("TEXT") button.  
In HD Radio source  
It can also be switched by pressing either [4] or  
[¢] button.  
Information  
Display  
Station name  
Song title/ Artist name/  
Album name/ Genre  
Frequency  
Clock  
"Station Name"  
"Title"  
In Tuner source  
Information  
Station name or Frequency  
Frequency  
Display  
"BAND+SNPS"  
"BAND+FREQ"  
"Clock"  
"Frequency"  
"Clock"  
Clock  
4 Exit Display Control mode  
Press the [6] button.  
In CD & External disc source  
Information  
Disc title  
Track title  
Track number & Play time  
Disc name  
Clock  
Display  
"D-TITLE"  
"T-TITLE"  
"P-Time"  
"DNPS"  
If the Disc title, Track title, Song title & Artist name, or  
Album name & Artist name is selected when the disc  
which does not have Disc title, Track title, Song title,  
Album name, or Artist name is played, track number  
and play time are displayed.  
"Clock"  
If the text for the Sirius tuner source, including  
Channel name, etc. is selected when the channel  
which does not have text for the Sirius tuner source,  
including Channel name, etc. is played, band &  
channel number is displayed.  
In MP3/WMA source  
Information  
Display  
"TITLE"  
"ALBUM"  
"FOLDER NAME"  
"FILE NAME"  
"P-Time"  
Song title & Artist name  
Album name & Artist name  
Folder name  
File name  
Play time & File number  
Clock  
Function of the KDC-MPV8025  
"Clock"  
Illumination Color Setting  
In Auxiliary input source  
You can set the display to a desired color.  
Information  
Auxiliary input name  
Clock  
Display  
"AUX Name"  
"Clock"  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "DISP" is  
displayed above the [3] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
|
16  
English  
Each time the button is pressed the character  
type switches as shown below.  
2 Enter display control mode  
Press the [3] ("DISP") button.  
Character type  
Alphabet (Upper case/ Lower case)  
Numbers and symbols  
Button  
3 Quick call up the preset color  
Press the [4] ("CLR") button.  
Each time the button is pressed the Color mode  
switches as shown below.  
[2] ("CAPS")  
[3] ("NUM")  
[4] ("CHAR")  
Special characters (Accent characters)  
Color mode  
Display  
5 Select the characters  
The color changes in sequence.  
Preset color (Silky White)  
Preset color (Red)  
Preset color (Blue)  
Preset color (Blue Green)  
Original color  
The color changes according  
to the selected source.  
The color changes every 6 hours. "COL Time"  
"COL Scan"  
"COL S.White"  
"COL Red"  
"COL Blue"  
"COL B.Green"  
"COL User"  
"COL SRC"  
Press the [FM] or [AM] button.  
Characters can be entered by using a remote with a  
number buttons.  
Example: If "DANCE" is entered.  
Character  
"D"  
Button  
[3]  
Times pressed  
1
1
2
3
2
"A"  
[2]  
"N"  
[6]  
The color continues to change gradually  
Hold down on the [4] or [¢] button.  
"COL User" is displayed.  
"C"  
[2]  
"E"  
[3]  
6 Repeat steps 3 through 5 and enter the name.  
Release your finger at the color you want.  
7 Exit name set mode  
Press the [NAME.S] button.  
4 Exit display control mode  
Press the [6] button.  
When operation stops for 10 seconds the name at  
that time is registered, and Name Set mode closes.  
Memory numbers  
- FM: 32 stations  
- AM: 16 stations  
Station/Disc Naming (SNPS/DNPS)  
Attaching a title to a Station or CD.  
- Internal CD player: 30 discs  
1 Receive/play the station/disc you want to  
attach a title to  
- External CD changer/ player: Varies according to the  
CD changer/ player. Refer to the CD changer/ player  
manual.  
The title of station/CD can be changed by the same  
operation used to name it.  
A title can’t be attached to an MD.  
Refer to the 'Text Display Switching' (page 16) and  
select either "DNPS" or "SNPS". No name can be  
attached to the source if "DNPS" or "SNPS" cannot be  
selected for it.  
2 Enter name set mode  
Press the [NAME.S] button for at least 2  
seconds.  
"NAME SET" is displayed.  
3 Move the cursor to the enter character  
position  
Press the [4] or [¢] button.  
4 Select the character type  
Press the [2] — [4] button.  
English  
|
17  
General features  
Each time the button is pressed the items that  
can be adjusted switch as shown below.  
Auxiliary Input Display Setting  
Selecting the display when this device is switched  
to Auxiliary input source.  
Adjustment Item  
Button  
[2]  
Display  
"ANG–"  
"ANG+"  
"SLD–"  
"SLD+"  
The panel tilts upwards.  
The panel tilts downwards.  
The panel slides backward.  
The panel slides forward.  
1 Select Auxiliary input source  
Press the [SRC] button.  
Select the "AUX"/"AUX EXT" display.  
[3]  
[4]  
[5]  
2 Enter Auxiliary input display setting mode  
Press the [NAME.S] button for at least 2  
seconds.  
4 Exit Panel Position Setting mode  
Press the [6] button.  
The presently selected AUX Name is blinks.  
The control panel may be interfered with the shift  
lever or another part depending on the angles of the  
control panel.  
Set the angle to avoid any interference.  
When a hard rubber frame is mounted  
Do not use with the panel slid in the forward  
direction.  
If so, the hard rubber frame will interfere with the  
panel when the angle is adjusted downward.  
No sound is produced while the panel is operating.  
3 Select the Auxiliary input display  
Press the [4] or [¢] button.  
Each time the button is pressed it switches  
through the below displays.  
• "AUX"/"AUX EXT"  
• "TV"  
• "VIDEO"  
• "GAME"  
• "PORTABLE"  
• "DVD"  
4 Exit Auxiliary input display setting mode  
Press the [NAME.S] button.  
Theft Deterrent Panel  
When operation stops for 10 seconds, the name  
at that time is selected, and Auxiliary input display  
setting mode closes.  
The Auxiliary Input Display can be set only when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S210A is used.  
The Backpanel of the unit can be detached and  
taken with you, helping to deter theft.  
Removing the Backpanel  
1 Turn the ignition OFF or press the [SRC]  
button for at least 1 second.  
Turn OFF the power, and the control panel  
becomes horizontal.  
Panel Position Setting  
After the set time passes in 'OFF Wait Time Setting'  
(page33), the panel is closed.  
Setting the angle or back-forward position of the  
control panel.  
2 Remove the Backpanel forward.  
When 'DSI (Disabled System Indicator)' (page32)  
is set to ON, DSI blinks.  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "PNL" is  
displayed above the [4] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
2 Enter Panel Position Setting mode  
Press the [4] ("PNL") button.  
3 Select the item for adjustment  
Press the desired [2] [5] button.  
|
18  
English  
The back panel is a precision piece of equipment and  
can be damaged by shocks or jolts. For that reason,  
keep the back panel in its special storage case while  
detached.  
Do not expose the Backpanel or its storage case to  
direct sunlight or excessive heat or humidity. Also  
avoid places with too much dust or the possibility of  
water splashing.  
Reattaching the Backpanel  
1 Set the Backpanel to the panel bracket.  
2 Hold down on the Backpanel until it is locked.  
TEL Mute  
The audio system automatically mutes when a  
call comes in.  
When a call comes in  
"CALL" is displayed.  
The audio system pauses.  
Listening to the audio during a call  
Press the [SRC] button.  
The "CALL" display disappears and the audio  
system comes back ON.  
When the call ends  
Hang up the phone.  
The "CALL" display disappears and the audio  
system comes back ON.  
English  
|
19  
Tuner features  
1 – 6  
NEXT  
SRC  
AUTO/AME  
AM  
FM  
4
¢
ST indicator  
Preset station number  
Band display  
Frequency display  
Tuning Mode  
Tuning  
Choose the tuning mode.  
Selecting the station.  
Press the [AUTO] button.  
Each time the button is pressed the Tuning  
mode switches as shown below.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUNER" display.  
Tuning mode  
Display  
Operation  
Automatic search for a station.  
2 Select the band  
Auto seek  
"Auto 1"  
Press the [FM] or [AM] button.  
Each time the [FM] button is pressed it switches  
between the FM1, FM2, and FM3 bands.  
Preset station seek "Auto 2"  
Search in order of the stations  
in the Preset memory.  
Normal manual tuning control.  
Manual  
"Manual"  
3 Tune up or down band  
Press the [4] or [¢] button.  
During reception of stereo stations the "ST" indicator  
is ON.  
|
20  
English  
Function of remote  
Auto Memory Entry  
Direct Access Tuning  
Putting stations with good reception in the  
memory automatically.  
Entering the frequency and tuning.  
1 Select the band for Auto Memory Entry  
Press the [FM] or [AM] button.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Open Auto Memory Entry  
2 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote.  
"– – – –" is displayed.  
Press the [AME] button for at least 2 seconds.  
When 6 stations that can be received are put in  
the memory Auto Memory Entry closes.  
3 Enter the frequency  
Press the number buttons on the remote.  
Example:  
Desired frequency  
92.1 MHz (FM)  
810 kHz (AM)  
Press button  
[0], [9], [2], [1]  
[0], [8], [1], [0]  
Preset Tuning  
Calling up the stations in the memory.  
Canceling Direct Access Tuning  
Press the [DIRECT] button on the remote.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until the function  
item is not displayed above the [2] — [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Station Preset Memory  
Putting the station in the memory.  
3 Call up the station  
Press the desired [1] [6] button.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Select the frequency to put in the memory  
Press the [4] or [¢] button.  
3 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until the function  
item is not displayed above the [2] — [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
4 Put the frequency in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the  
memory on each [1] — [6] button.  
English  
|
21  
CD/MP3/WMA/External disc control features  
2 – 5  
NEXT  
0
SRC  
38  
SCRL DISC–/ DISC+/  
FM  
4
¢
AM  
Track number  
IN indicator  
Disc number  
Track time  
Each time the button is pressed the song pauses  
or plays.  
Playing CD & MP3/WMA  
When there is no disc inserted  
Eject the disc  
1 Open the panel to insert disc  
1 Eject the disc  
Press the [0] button.  
Press the [0] button.  
2 Insert a disc.  
2 Return the panel to the original position  
Press the [0] button.  
When the faceplate has been slid open, it might  
interfere with the shift lever or something else. If this  
happens, pay attention to safety and move the shift  
lever or take an appropriate action, then operate the  
unit.  
3 in. (8cm) disc can’t be played. Using an adapter and  
inserting them into this unit can cause damage.  
The MP3/WMA media that this unit can play are CD-  
ROM, CD-R, and CD-RW.  
The sound will be temporarily muted while the  
faceplate is moving.  
When a disc is inserted the "IN" indicator is ON.  
The medium formats must be ISO 9660 Level 1, Level  
2, Joliet, or Romeo. The methods and precautions to  
be followed for writing MP3/WMA data are covered  
in 'Notes on playing MP3/WMA' (page 8). Check that  
section before creating your MP3/WMA media.  
When a disc is inserted  
Press the [SRC] button.  
Select the "CD" display.  
Pause and play  
Press the [38] button.  
|
22  
English  
Function of remote  
Playing External Disc  
Direct Track/File Search  
Playing discs set in the optional accessory disc  
player connected to this unit.  
Doing Track/File Search by entering the track/file  
number.  
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
1 Enter the track/file number  
Press the number buttons on the remote.  
Display  
"CD2"  
"CD CH"  
"MD CH"  
Disc player  
CD player  
CD changer  
MD changer  
2 Do Track/File Search  
Press the [4] or [¢] button.  
Canceling Direct Track/File Search  
Press the [38] button.  
Pause and play  
Press the [38] button.  
Each time the button is pressed it pauses and  
plays.  
Function of disc changers with remote  
Direct Disc Search  
Doing Disc Search by entering the disc number.  
Disc 10 is displayed as "0".  
The functions that can be used and the information  
that can be displayed will differ depending on the  
external disc players being connected.  
1 Enter the disc number  
Press the number buttons on the remote.  
2 Do Disc Search  
Press the [DISC+] or [DISC–] button.  
Canceling Direct Disc Search  
Press the [38] button.  
Fast Forwarding and Reversing  
Fast Forwarding  
Hold down on the [¢] button.  
Release your finger to play the disc at that point.  
Input "0" to select disc 10.  
Reversing  
Hold down on the [4] button.  
Release your finger to play the disc at that point.  
Track/File Search  
Searching for a song on the disc or in the MP3/  
WMA folder.  
Press the [4] or [¢] button.  
Function of disc changer/ MP3/ WMA  
Disc Search/Folder Search  
Selecting the disc set in the Disc changer or the  
folder recorded on the MP3/WMA media.  
Press the [DISC–] or [DISC+] button.  
English  
|
23  
CD/MP3/WMA/External disc control features  
Track/File/Disc/Folder Repeat  
Random Play  
Replaying the song, disc in the Disc changer or  
MP3/WMA folder you’re listening to.  
Play all the songs on the disc or MP3/WMA folder  
in random order.  
1 Select the key function section  
Press the [NEXT] button.  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "REP" is  
displayed above the [4] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Repeatedly press the button until "RDM" is  
displayed above the [3] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
2 Turn ON/OFF the Repeat Play  
Press the [4] ("REP") button.  
Each time the button is pressed the Repeat Play  
switches as shown below.  
2 Turn ON/OFF the Random Play  
Press the [3] ("RDM") button.  
Each time the button is pressed Random Play  
turns ON or OFF.  
When it’s ON, "Random ON" is displayed.  
In CD & External disc source  
Repeat play  
Track Repeat  
Disc Repeat (In Disc Changer)  
OFF  
Display  
When the [¢] button is pressed, the next song  
select starts.  
"(T-)Repeat ON"  
"D-Repeat ON"  
"Repeat OFF"  
In MP3/WMA source  
Function of disc changer  
Repeat play  
File Repeat  
Folder Repeat  
OFF  
Display  
Magazine Random Play  
"File REP ON"  
"FOLD REP ON"  
"Repeat OFF"  
Play the songs on all the discs in the disc changer  
in random order.  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "MRDM" is  
displayed above the [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Scan Play  
Playing the first part of each song on the disc  
or MP3/WMA folder you are listening to and  
searching for the song you want to listen to.  
2 Turning ON/OFF the Magazine Random Play  
Press the [5] ("MRDM") button.  
Each time the button is pressed the Magazine  
Random Play turns ON or OFF.  
1 Select the key function section  
Press the [NEXT] button.  
Repeat to press the button until "SCAN" is  
displayed above the [2] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
When it’s ON, "M-Random ON" is displayed.  
When the [¢] button is pressed, the next song  
select starts.  
2 Start Scan Play  
Press the [2] ("SCAN") button.  
"Scan ON" is displayed.  
3 Release it when the song you want to listen  
to is played  
Press the [2] button.  
|
24  
English  
Function of MP3/WMA  
Text/Title Scroll  
Folder Select  
Scrolling the displayed CD text, MP3/WMA text,  
or MD title.  
Quickly selecting the folder you want to listen to.  
Press the [SCRL] button.  
1 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until "FSEL" is  
displayed above the [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
Function of disc changers with remote  
DNPP (Disc Name Preset Play)  
2 Enter Folder Select mode  
Press the [5] ("FSEL") button.  
"Select Mode" is displayed.  
Selecting the CD displayed in the DNPS of the  
CDs set in the Disc changer.  
During Select mode the folder information is  
displayed as shown below.  
Folder name display  
1 Enter DNPP mode  
Press the [DNPP] button on the remote.  
When "DNPP" is displayed the DNPS display in  
order.  
Displays the current folder name.  
Forward / Reverse display  
Press the [DISC–] or [DISC+] button.  
2 When the disc you want is displayed  
Press the [OK] button on the remote.  
The disc being displayed is played.  
3 Select the folder level  
Press the [FM] or [AM] button.  
With the [FM] button you move 1 level down and  
with the [AM] button 1 level up.  
Canceling the DNPP mode  
Press the [DNPP] button on the remote.  
Selecting a folder in the same level  
Press the [4] or [¢] button.  
With the [4] button you move to the previous  
folder, and with the [¢] button to the next  
folder.  
Returning to the top level  
Press the [4] ("HOME") button.  
Scrolling the folder name display  
Press the [SCRL] button.  
4 Decide the folder to play  
Press the [2] ("OK") button.  
The Folder Select mode releases, and the MP3/  
WMA in the folder being displayed is played.  
The methods for moving to other folders in the folder  
select mode are different from those in the folder  
search mode.  
See 'Notes on playing MP3/WMA' (page 8) for details.  
Canceling the Folder Select mode  
Press the [3] ("EXIT") button.  
English  
|
25  
SIRIUS tuner control features  
1 – 6  
NEXT  
SRC  
AUTO SCRL  
FM  
4
¢
Select SIRIUS Satellite Radio Mode  
Display  
"Channel"  
"Preset"  
Operation  
Normal manual seeking control.  
Search in order of the channels in the Preset  
memory.  
Selecting the SIRIUS Satellite Radio Tuner  
(optional accessory) connected to this unit.  
Selecting SIRIUS Mode  
Press the [SRC] button.  
Select the "SIRIUS" display.  
Select the channel  
Selecting the channel.  
You need to subscribe to SIRIUS to receive the service  
by SIRIUS Satellite Radio. Consult SIRIUS if "CALL 888-  
539-SIRIUS TO SUBSCRIBE" appears.  
Press the [4] or [¢] button.  
It may take a little time to start receiving after you  
selected the SIRIUS source.  
If the signal receiving fails, "Acquiring Signal" appears.  
Channel Search  
Selecting the channel and category you want to  
receive.  
Switching Seek Mode  
1 Select the key function section  
Press the [NEXT] button.  
Sets the seeking mode.  
Press the [AUTO] button.  
Each time the button is pressed the Seek mode  
switches as shown below.  
Repeatedly press the button until "CH+"/ "CH–"/  
"CS+"/ "CS–" is displayed above the [2] [5]  
button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
|
26  
English  
2 Select the item for adjustment  
Press the desired [2] [5] button.  
Each time the button is pressed the items that  
can be adjusted switch as shown below.  
Channel Preset Memory  
Putting the channel in the memory.  
1 Select the preset band  
Press the [FM] button.  
Adjustment Item  
Button Display  
Search down in category  
Search up in category  
Search down for channel in selected category [4]  
Search up for channel in selected category [5]  
[2]  
[3]  
"CS–"  
"CS+"  
"CH–"  
"CH+"  
2 Select the channel to put in the memory  
Press the [4] or [¢] button.  
3 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until the function  
item is not displayed above the [2] — [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
You cannot operate this unit until all the Category  
information is acquired.  
4 Put the channel in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
Function of remote  
The preset number display blinks 1 time.  
On each band, 1 channel can be put in the  
memory on each [1] — [6] button.  
Direct Access Tuning  
Entering the channel and tuning.  
1 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote.  
Only the channel number is stored. Category  
information is not stored.  
2 Enter the channel  
Press the number buttons.  
3 Do Channel Search  
Press the [4] or [¢] button.  
Preset Tuning  
Canceling Direct Access Tuning  
Calling up the channels in the memory.  
Press the [DIRECT] button on the remote.  
1 Select the preset band  
Press the [FM] button.  
If you make no button operation for 10 seconds, the  
Direct Access Tuning mode is automatically canceled.  
You can set up to Channel number 223.  
If there is no signal in the input Channel, "NO CH"  
appears.  
2 Select the key function section  
Press the [NEXT] button.  
Repeatedly press the button until the function  
item is not displayed above the [2] — [5] button.  
Refer to 'Notes on Multi-function Key System'  
(page 10).  
If you cannot receive any signal in the input Channel  
due to a bad condition on radio wave or another  
problem, "Acquiring Signal" appears.  
3 Call up the channel  
Press the desired [1] — [6] button.  
Selecting the Preset Band  
Press the [FM] button.  
Each time the button is pressed the preset band  
switches between the SR1, SR2, SR3 and SR4.  
English  
|
27  
SIRIUS tuner control features  
Channel Scan  
Every receivable Channel is checked for 10  
seconds.  
1 Start Channel Scan  
Press the [AUTO] button for at least 1 second.  
The channel number display blinks.  
2 Release it when the song you want to listen  
to is received  
Press the [AUTO] button for at least 1 second.  
Text Scroll for SIRIUS tuner source  
Scrolls the displayed channel name and other  
items.  
Press the [SCRL] button.  
|
28  
English  
HD Radio control features  
SRC  
MENU  
AM  
FM  
4
¢
ST indicator  
Preset station number  
Band display  
Frequency display  
The HD Radio cannot be selected as a dual zone  
source.  
Tuning  
Selecting the station.  
1 Select HD Radio source  
Press the [SRC] button.  
Select the "HD Radio" display.  
2 Select the HF band  
Press the [FM] button.  
Each time the [FM] button is pressed it switches  
between the HF1, HF2, and HF3 bands.  
Select the HA band  
Press the [AM] button.  
3 Tune up or down band  
Press the [4] or [¢] button.  
When you connect an HD Radio, Tuner features of  
the unit are disabled and switched to HD Radio tuner  
features. A portion of the setting methods including  
the Tuning Mode will change.  
• With the HD Radio tuner, you can use the similar  
functions to 'Station Preset Memory', and 'Preset  
Tuning' of Tuner features. Refer to Tuner features for  
how to use the functions.  
English  
|
29  
HD Radio control features  
Auto Memory Entry  
Putting a station with good reception in the  
memory automatically.  
1 Select the band for Auto Memory Entry  
Press the [FM] or [AM] button.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
3 Select the Auto Memory Entry mode  
Press the [FM] or [AM] button.  
Select the "Auto-Memory" display.  
4 Open Auto Memory Entry  
Press the [4] or [¢] button for at least 2  
seconds.  
When 6 stations that can be received are put in  
the memory Auto Memory Entry closes.  
5 Exit Menu mode  
Press the [MENU] button.  
The receiving method can be switched with the  
setting of 'Receive mode Setting' (page 35).  
|
30  
English  
Menu system  
SRC  
MENU  
AM  
FM  
4
¢
Menu System  
4 Exit Menu mode  
Press the [MENU] button.  
Setting during operation beep sound etc.  
functions.  
The Menu system basic operation method is  
explained here. The reference for the Menu items  
and their setting content is after this operation  
explanation.  
When other items that are applicable to the basic  
operation method above are displayed afterwards  
their setting content chart is entered. (Normally the  
uppermost setting in the chart is the original setting.)  
Also, the explanation for items that aren’t applicable  
('Manual Clock Adjustment' etc.) are entered step by  
step.  
1 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
2 Select the menu item  
Press the [FM] or [AM] button.  
Example: When you want to set the beep sound  
select the "Beep" display.  
3 Set the menu item  
Press the [4] or [¢] button.  
Example: When "Beep" is selected, each time the  
button is pressed it switches "Beep ON"  
or "Beep OFF". Select 1 of them as the  
setting.  
You can continue by returning to step 2 and  
setting other items.  
English  
|
31  
Menu system  
In Standby mode  
The unit can be used.  
Security Code  
Because authorization by the Security Code is  
required when it’s removed from the vehicle,  
personalizing this unit is by using the Security  
Code is a help in preventing theft.  
Touch Sensor Tone  
Setting the operation check sound (beep sound)  
ON/OFF.  
When the Security Code function is activated, the code  
can’t be changed and the function can’t be released.  
Note, the Security Code can be set as the 4 digit number  
of your choice.  
Display  
"Beep ON"  
"Beep OFF"  
Setting  
Beep is heard.  
Beep canceled.  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
Manual Clock Adjustment  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
When "MENU" is displayed, "Security" is displayed.  
1 Select Clock Adjustment mode  
Press the [FM] or [AM] button.  
Select the "Clock Adjust" display.  
3 Enter Security Code mode  
Press the [4] or [¢] button for at least 1  
second.  
2 Enter Clock Adjust mode  
Press the [4] or [¢] button for at least 1  
second.  
When "ENTER" is displayed, "CODE" is displayed.  
The clock display blinks.  
4 Select the digits to enter  
Press the [4] or [¢] button.  
3 Adjust the hours  
Press the [FM] or [AM] button.  
5 Select the Security Code numbers  
Press the [FM] or [AM] button.  
Adjust the minutes  
Press the [4] or [¢] button.  
6 Repeat steps 4 and 5, and complete the  
Security Code.  
4 Exit Clock adjustment mode  
Press the [MENU] button.  
7 Confirm the Security Code  
Press the [¢] button for at least 3 seconds.  
When "RE-ENTER" is displayed, "CODE" is  
displayed.  
8 Do the step 4 through 7 operation, and  
reenter the Security Code.  
"APPROVED" is displayed.  
DSI (Disabled System Indicator)  
A red indicator will blink on the unit after the  
faceplate is removed, warning potential thieves.  
The Security Code function activates.  
Display  
"DSI ON"  
"DSI OFF"  
Setting  
LED flashes.  
LED OFF.  
When the wrong Code is entered in steps 4 through 6,  
repeat from step 4.  
Press the Reset button and when its removed  
from the battery power source  
1 Turn the power ON.  
2 Do the step 4 through 7 operation, and enter  
the Security Code.  
"APPROVED" is displayed.  
|
32  
English  
Selectable Illumination  
OFF Wait Time Setting  
Selecting the button illumination color as green  
or red.  
Setting the time until the faceplate hide  
operation starts after the power is turned OFF.  
The faceplate can be removed only during the set  
time period.  
Display  
Setting  
"Button Red"  
"Button Green"  
The illumination color is red.  
The illumination color is green.  
Display and Setting  
"Off Wait 0s"  
"Off Wait 3s" (Original setting)  
"Off Wait 25s"  
Triangle indicator setting  
Sets the blinking mode during triangle indicator  
system adjustment (such as audio control, multi-  
key system setup).  
In Standby mode  
Display  
"Blink ON"  
"Blink OFF"  
Setting  
Eject angle setting  
The Triangle indicator blinks.  
The Triangle indicator does not blink.  
This function sets the opening and closing  
operation of a panel when a disc is inserted and  
when it is ejected.  
Contrast Adjustment  
Display  
Setting  
"EJCT ANG SLP"  
Opens and closes the panel while maintaining  
the angle of the control panel to the set angle.  
Adjusting the display contrast.  
Display and Setting  
"Contrast 0"  
"EJCT ANG LVL"  
Opens and closes the panel after setting the  
angle of the control panel to the horizontal  
position.  
"Contrast 5" (Original setting)  
"Contrast 10"  
In Standby mode  
Panel action setting  
Sets the panel movement when the panel action  
(back/forward movement) is set to its most end  
position.  
Dimmer  
Dimming this unit’s display automatically when  
the vehicle light switch is turned ON.  
Display  
Setting  
Display  
"Dimmer ON"  
"Dimmer OFF"  
Setting  
The display dims.  
The display doesn’t dim.  
"PanelCNT 1"  
No angle can be adjusted if the panel position  
has been set to its most end position. Also, if you  
have set the angle below the horizontal position,  
the angle is set to horizontal when you set the  
panel to its most end position.  
"PanelCNT 2"  
The angle can be adjusted regardless of the  
panel position.  
English  
|
33  
Menu system  
In Standby mode  
Display  
Setting  
"CRSC ON"  
"CRSC OFF"  
The CRSC is ON.  
The CRSC is OFF.  
Switching preout  
Switching the preout between the rear and  
subwoofer. (In subwoofer it outputs without  
effect from the fader control.)  
Strong electrical fields (such as from power lines) may  
cause unstable sound quality when CRSC is turned  
ON. In such a situation, turn it OFF.  
Display  
"SWPRE Rear"  
"SWPRE Sub-W"  
Setting  
Rear preout.  
Subwoofer preout.  
Text Scroll  
Setting the displayed text scroll.  
In Standby mode  
Built-in Amp Mute Setting  
Display  
Setting  
"Scroll Auto"  
"Scroll MANU"  
Repeats scroll.  
Scrolls when the display changes.  
Toggles ON or OFF the mute control on the built-  
in amplifier.  
Turning ON this control enhances the preout  
quality.  
The text scrolled is shown below.  
Display  
Setting  
- CD text  
- Folder name/ File name/ Song title/ Artist name/  
Album name  
- MD title  
"AMP Mute OFF"  
"AMP Mute ON"  
The built-in amplifier activates.  
The built-in amplifier deactivates.  
- Text for the SIRIUS tuner source, HD Radio source,  
including Channel name, etc.  
In SIRIUS tuner source  
SIRIUS ID (ESN) display  
Function of the KDC-MPV8025  
Displaying the SIRIUS ID (Electronic Serial  
Number) display.  
Built-in Auxiliary input Setting  
Set the Built-in Auxiliary Input function.  
Display  
"ESN = ************"  
Display  
"AUX OFF" When selecting the source there’s no Auxiliary Input.  
"AUX ON" When selecting the source there’s Auxiliary Input.  
Setting  
Serial & SIRIUS ID (ESN)  
It is especially important to retain the unit serial  
number and the electronic SIRIUS Identification  
number for service activation and potential future  
service changes.  
In Standby mode  
CD Read Setting  
When there is a problem on playing a CD with  
special format, this setting play the CD by force.  
In FM reception  
CRSC (Clean Reception System  
Circuit)  
Display  
"CD READ 1"  
"CD READ 2"  
Setting  
Play CD and MP3/WMA.  
Play CD by force.  
Temporarily have reception switched from  
stereo to mono to reduce multi-path noise when  
listening to the FM station.  
|
34  
English  
mode switches as shown below.  
Setting "CD READ 2" cannot play MP3/WMA.  
Some music CDs may not be played back even in the  
"CD READ 2" mode.  
Receive mode Display  
Operation  
Auto mode  
"Auto"  
Analog broadcasts and digital  
broadcasts will be switched  
automatically.  
When both are being transmitted,  
the digital broadcast will have  
priority.  
Digital broadcasts only.  
Analog broadcasts only.  
Rotary volume operation select  
Digital  
Analog  
"Digital"  
"Analog"  
Various items can be set using the rotary volume  
knob.  
4 Exit Receive mode  
Press the [MENU] button.  
Display  
"Rotary ON"  
Setting  
The rotary volume knob can be used for item  
setup.  
"Rotary OFF"  
The rotary volume knob cannot be used for  
item setup.  
Even if the "Auto" setting, an analog broadcast will be  
received during the reception of a ball game mode  
(non-delayed broadcast program).  
To use the rotary volume knob for item setup, select  
"Rotary ON" and press the [1] button in each setup  
mode.  
In HD Radio mode  
Auto Memory Entry  
For the operation method refer to 'Auto Memory  
Entry' (page 30).  
In HD Radio mode  
Tuning Mode  
Sets the tuning mode.  
Tuning mode  
Auto seek  
Display  
"Auto 1"  
Operation  
Automatic search for a station.  
Preset station seek "Auto 2"  
Search in order of the stations  
in the Preset memory.  
Manual  
"Manual"  
Normal manual tuning control.  
In HD Radio mode  
Receive mode Setting  
Sets the receive mode.  
1 Select the Receive mode  
Press the [FM] or [AM] button.  
Select the "Receive Mode" display.  
2 Enter Receive mode  
Press the [4] or [¢] button for at least 1  
second.  
3 Set the Receive mode  
Press the [FM] or [AM] button.  
Each time the button is pressed the Receive  
English  
|
35  
Basic Operations of remote  
SRC  
ATT  
SRC  
VOL.  
ATT  
38  
VOL.  
FM+  
38  
FM/AM/DISC+/DISC–  
DISC  
4
¢
AM–  
4/¢  
DNPP  
DNPP  
/SBF  
DIRECT  
/OK  
Not Used  
DIRECT/OK  
ABC  
JKL  
TUV  
QZ  
DEF  
MNO  
WXY  
GHI  
[0] — [9]  
PRS  
Loading and Replacing the battery  
Basic operations  
Use two "AA"-size batteries.  
[VOL.] buttons  
Slide the cover while pressing downwards to  
remove it as illustrated.  
Adjusting the volume.  
[SRC] button  
Each time the button is pressed the source  
switches.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
For the source switching order refer to 'Selecting  
the Source' (page 12).  
[ATT] button  
Turning the volume down quickly.  
When it is pressed again it returns to the previous  
level.  
2WARNING  
Store unused batteries out of the reach of children.  
Contact a doctor immediately if the battery is  
accidentally swallowed.  
Do not set the remote on hot places such as above  
the dashboard.  
|
36  
English  
In Tuner source  
In SIRIUS tuner source  
[FM]/ [AM] buttons  
[FM] buttons  
Select the band.  
Select the preset band.  
Each time the [FM] button is pressed it switches  
between the FM1, FM2, and FM3 bands.  
[4]/ [¢] buttons  
Search up or down channel.  
[4]/ [¢] buttons  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset channels.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
[DIRECT]/ [OK] button  
Enters and cancels the 'Direct Access Tuning'  
(page 27) mode.  
[DIRECT]/ [OK] button  
Enters and cancels the 'Direct Access Tuning'  
(page 21) mode.  
In HD Radio source  
[FM] button  
Select the HF band.  
In Disc source  
Each time the [FM] button is pressed it switches  
between the HF1, HF2, and HF3 bands.  
[4]/ [¢] buttons  
Doing track/file forward and backward.  
[AM] button  
[DISC+]/ [DISC–] buttons  
Select the HA band.  
Doing disc/folder forward and backward.  
[4]/ [¢] buttons  
[38] button  
Each time the button is pressed the song pauses  
and plays.  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
[DNPP] button  
Enters and cancels the 'DNPP (Disc Name Preset  
Play)' (page 25) mode.  
[0] — [9] buttons  
When in 'Direct Track/File Search' (page 23) and  
'Direct Disc Search' (page 23), enter the track/file/  
disc number.  
English  
|
37  
Accessories/ Installation Procedure  
Accessories  
Installation Procedure  
1. To prevent a short circuit, remove the key from  
the ignition and disconnect the - battery.  
2. Make the proper input and output wire  
connections for each unit.  
1
3. Connect the speaker wires of the wiring harness.  
4. Connect the wiring harness wires in the  
following order: ground, battery, ignition.  
..........1  
5. Connect the wiring harness connector to the  
unit.  
6. Install the unit in your car.  
2
7. Reconnect the - battery.  
8. Turn the vehicle’s ignition key on and open the  
panel.  
9. Press the [5] button and the reset button.  
..........2  
2WARNING  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
3
..........4  
If your car’s ignition does not have an ACC position,  
connect the ignition wires to a power source that can be  
turned on and off with the ignition key. If you connect  
the ignition wire to a power source with a constant  
voltage supply, as with battery wires, the battery may die.  
If the console has a lid, make sure to install the unit so  
that the faceplate will not hit the lid when closing and  
opening.  
4
..........4  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with  
one with the same rating.  
Insulate unconnected wires with vinyl tape or other  
similar material. To prevent a short circuit, do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
5
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail  
to work if you share the - wires or ground them to any  
metal part in the car.  
..........2  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals  
(do not mix front and rear). For example, if you connect  
the + connector of the left speaker to a front output  
terminal, do not connect the - connector to a rear  
output terminal  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
|
38  
English  
Connecting Wires to Terminals  
Front right output (Red)  
Front left output (White)  
AUX right input (Red) (KDC-MPV8025 only)  
AUX left input (White) (KDC-MPV8025 only)  
Rear right output (Red)/  
Subwoofer right output (Red)  
Rear left output (White)/  
Subwoofer left output (White)  
To KENWOOD disc changer/  
Sirius satellite radio tuner/  
External optional accessory  
Fuse (10A)  
To connect these leads,  
refer to the relevant  
instruction manuals.  
FM/AM antenna input  
If no connections are made, do not let the  
wire come out from the tab.  
Wiring harness  
(Accessory1)  
When using the optional power amplifier, connect to its  
power control terminal.  
P.CONT  
Power control wire (Blue/White)  
Depending on what antenna you are using, connect either  
to the control terminal of the motor antenna, or to the  
power terminal for the booster amplifier of the film-type  
antenna.  
ANT.  
CONT  
Motor antenna control wire (Blue)  
Connect to the terminal that is grounded when either the  
telephone rings or during conversation.  
TEL MUTE  
TEL mute wire (Brown)  
To car light control switch  
Dimmer control wire (Orange / White)  
White/Black  
White  
To front left speaker  
To front right speaker  
To rear left speaker  
FRONT • L  
Gray/Black  
Gray  
FRONT • R  
REAR • L  
Green/Black  
Green  
Purple/Black  
Purple  
To rear right speaker  
REAR • R  
Ignition key  
switch  
ACC  
Ignition wire (Red)  
Car fuse box  
Car fuse box  
(Main fuse)  
Battery wire (Yellow)  
Ground wire (Black) - (To car chassis)  
Battery  
+
English  
|
39  
Installation  
non-Japanese cars  
Japanese cars  
1 Refer to the section 'Removing the hard rubber  
frame' (page 42) and then remove the hard  
rubber frame.  
2 Align the holes in the unit (two locations on each  
side) with the vehicle mounting bracket and  
secure the unit with the accessory screws.  
Metal mounting strap  
(commercially available)  
Firewall or metal support  
T
N
T/N  
T
N
Bend the tabs of the  
T: Toyota cars  
N: Nissan cars  
mounting sleeve with a  
screwdriver or similar utensil  
and attach it in place.  
8 mm  
MAX.  
Phillips truss head sheet metal screw  
(commercially available)  
8mm  
MAX.  
3
4
ø5mm  
ø5mm  
Screw (M4X8)  
(commercially available)  
Accessory3...for Nissan car  
Accessory4 ...for Toyota car  
Make sure that the unit is installed securely in place. If  
the unit is unstable, it may malfunction (for example, the  
sound may skip).  
During installation, do not use any screws except for  
those provided. The use of different screws might result  
in damage to the main unit.  
Damage may occur if a screwdriver or similar tool is used  
with excessive force during the installations.  
To attach this unit, make sure the front of the control  
panel faces you and fit it into the mounting sleeve by  
pressing the four corners of the hard rubber frame at the  
same time.  
Do not apply strong pressure to other sections than the  
corners; otherwise troubles such as the impossibility of  
opening or closing the panel may result.  
The hollow at the center of the rubber frame is designed  
to make it easier to remove discs.  
If you do not want the hollow to be visible, mount the  
rubber frame in the opposite direction (with the flat side  
at the top instead of the bottom).  
|
40  
English  
Installation  
Locking the Backpanel to the unit  
If you want to fasten the faceplate to the main  
unit so that it does not fall off.  
1 Refer to the Removing the Backpanel function of  
the section on 'Theft Deterrent Panel' (page 18)  
and remove the Backpanel.  
2 Insert the panel lock screws into the holes at the  
sides of the panel.  
Accessory5  
3 Reattach the Backpanel.  
Never insert the panel lock screws in any other screw  
holes than the one specified. If you insert them in  
another hole, it will contract and may cause damage to  
the mechanical parts inside the unit.  
English  
|
41  
Removing the Unit  
Removing the hard rubber frame  
Removing the Unit  
1 Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
1 Refer to the section 'Removing the hard rubber  
frame' (page 42) and then remove the hard  
rubber frame.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots  
on each side, as shown.  
Screw (M4X8)  
(commercially available)  
Lock  
Catch  
Accessory2  
Removal tool  
2 When the upper level is removed, remove the  
lower two locations.  
Accessory2  
Removal tool  
4 Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
The frame can be removed from the bottom side in the  
same manner.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5 Pull the unit all the way out with your hands,  
being careful not to drop it.  
|
42  
English  
Troubleshooting Guide  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
? No sound can be heard, or the volume is low.  
The fader or balance settings are set all the way to  
one side.  
Center the fader and balance settings.  
The input/output wires or wiring harness are  
connected incorrectly.  
Reconnect the input/output wires or the  
wiring harness correctly. See the section on  
'Connecting Wires to Terminals'.  
General  
? The power does not turn ON.  
The fuse has blown.  
The values of Volume offset are low.  
After checking for short circuits in the wires,  
replace the fuse with one with the same  
rating.  
Turn up the Volume offset, referring to the  
section on 'Audio Control' (page 12).  
The 'Built-in Amp Mute Setting' (page 34) is ON.  
Turn it OFF.  
Speaker cable touches on chassis etc.  
Wire or insulate the speaker cable properly  
and press the reset button.  
? The sound quality is poor or distorted.  
One of the speaker wires is being pinched by a  
screw in the car.  
The Demonstration mode has been selected.  
Hold down button [5] and press the Reset  
button to release the Demonstration mode.  
Check the speaker wiring.  
The speakers are not wired correctly.  
? There’s a source you can’t switch.  
Reconnect the speaker wires so that each  
output terminal is connected to a different  
speaker.  
There’s no media inserted.  
Set the media you want to listen to. If there’s  
no media in this unit, you can’t switch to each  
source.  
? The Touch Sensor Tone doesn’t sound.  
The preout jack is being used.  
The Disc changer isn’t connected.  
The Touch Sensor Tone can’t be output from  
the preout jack.  
Connect the Disc changer. If the Disc changer  
isn’t connected to it’s input terminal, You can’t  
switch to an external disc source.  
? The Dimmer function doesn’t work.  
The Dimmer wire isn’t connected correctly.  
Check the Dimmer wire connection.  
? The memory is erased when the ignition is  
turned OFF.  
The ignition and battery wire are incorrectly  
connected.  
? The display color changes subtly.  
This is because the temperature is different than  
the temperature when the setting was done.  
Connect the wire correctly, referring to the  
section on 'Connecting Wires to Terminals'.  
The display color condition changes subtly  
according.to the ambient temperature.  
? There’s no loudness effect.  
You’re using Subwoofer preout.  
Loudness has no effect in Subwoofer preout.  
? The panel is not hidden even when the power is  
turned off.  
The protection function for preventing fingers or  
other things from getting caught in between the  
panel and this unit has been activated.  
? The TEL mute function does not work.  
The TEL mute wire is not connected properly.  
Connect the wire correctly, referring to the  
section on 'Connecting Wires to Terminals'.  
Turn off the power again.  
? The Control Panel moves although you do not  
desire.  
? The TEL mute function turns ON even though the  
TEL mute wire is not connected.  
The Demonstration mode has been selected.  
The TEL mute wire is touching a metal part of the  
Hold down button [5] and press the Reset  
button to release the Demonstration mode.  
car.  
Pull the TEL mute wire away from the metal  
part of the car.  
? Even if Loudness is turned ON, high-pitched tone  
isn’t compensated for.  
Tuner source is selected.  
High-pitched tone isn’t compensated for when  
in Tuner source.  
English  
|
43  
Troubleshooting Guide  
Tuner source  
? Track Search can’t be done.  
For the discs/folders first or last song.  
? Radio reception is poor.  
For each disc/folder, Track Search can’t be  
done in the backward direction for the first  
song or in the forward direction for the last  
song.  
The car antenna is not extended.  
Pull the antenna out all the way.  
The antenna control wire is not connected.  
Connect the wire correctly, referring to the  
section on 'Connecting Wires to Terminals'.  
MP3/WMA source  
? The desired frequency can’t be entered with the  
Direct Access Tuning.  
? Cannot play an MP3/WMA.  
The media is scratched or dirty.  
A station that can’t be received is being entered.  
Clean the media, referring to the CD cleaning  
of the section on 'About CDs' (page 7).  
Enter a station that can be received.  
You’re trying to enter a frequency with a 0.01 MHz  
unit.  
? The sound skips when an MP3/WMA is being  
played.  
What can be designated in the FM band is to  
0.1 MHz.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning  
of the section on 'About CDs' (page 7).  
Disc source  
The recording condition is bad.  
Record the media again or use another media.  
? "AUX EXT" is displayed without achieving  
External disc control mode.  
Unsupported disc changer is connected.  
? The MP3/WMA track time isn’t displayed  
correctly.  
Use the disc changer mentioned in the  
'About CD players/disc changers connected  
to this unit' (page 5) of the section on 'Safety  
precautions'.  
---  
There are times when it isn’t displayed  
correctly according to the MP3/WMA  
recording conditions.  
? The specified disc does not play, but another one  
plays instead.  
HD Radio source  
The specified CD is quite dirty.  
Clean the CD.  
? No sound can be heard, or the volume is low.  
The disc is loaded in a different slot from that  
specified.  
The preset broadcast station is not transmitting  
in the mode that was set with 'Receive mode  
Setting' (page 35).  
Eject the disc magazine and check the  
number for the specified disc.  
Please set 'Receive mode Setting' to "Auto".  
The disc is severely scratched.  
Try another disc instead.  
In digital AM broadcasting, receive mode switches  
between stereo and monaural too often.  
Receiving condition is bad or unstable.  
Stereo is chosen when receiving condition is  
good, and it switches to monaural when the  
condition becomes bad.  
? A CD ejects as soon as it is loaded.  
The CD is quite dirty.  
Clean the CD, referring to the CD cleaning of  
the section on 'About CDs' (page 7).  
HD Radio tuner is connected to KCA-S210A or  
other units.  
? Can’t remove disc.  
The cause is that more than 10 minutes has  
Connect the HD Radio tuner directly to the  
control unit.  
elapsed since the vehicle ACC switch was turned  
OFF.  
The disc can only be removed within 10  
minutes of the ACC switch being turned OFF.  
If more than 10 minutes has elapsed, turn  
the ACC switch ON again and press the Eject  
button.  
If the following situations, consult your  
nearest service center:  
Even though the disc changer is connected, the  
Disc Changer source is not ON, with "AUX EXT"  
showing in the display during the Changer Mode.  
? The disc won’t insert.  
There’s already another disc inserted.  
Press the [0] button and remove the disc.  
? Direct Search can’t be done.  
Another function is ON.  
Turn Random Play or other functions OFF.  
|
44  
English  
NO NAME:  
• Attempted to display DNPS during the CD  
play having no disc names preset.  
• Attempted to display the ID3 tag while  
the MP3/WMA having no ID3 tag is being  
played.  
The messages shown below display your  
systems condition.  
EJECT:  
No disc magazine has been loaded in  
the changer. The disc magazine is not  
completely loaded.  
Waiting:  
Load:  
Radio text data is being received.  
Load the disc magazine properly.  
No CD in the unit.  
Insert the CD.  
Discs are being exchanged in the Disc  
changer.  
No Disc:  
No disc has been loaded in the disc  
magazine.  
Reading:  
The unit is reading the data on the disc.  
Load a disc into the disc magazine.  
NO ACCESS:  
After setting it in the Disc Changer, DNPP  
was done without having it been played at  
least 1 time.  
TOC Error:  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
Clean the CD and load it correctly.  
IN (Blink):  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
E-05:  
The CD is upside-down.  
Load the CD correctly.  
Blank Disc:  
No Track:  
Nothing has been recorded on the MD.  
Unsupported File:  
A MP3/WMA is played with a format that  
No tracks are recorded on the MD,  
although it has a title.  
this unit can’t support.  
----  
E-15:  
Media was played that doesn’t have data  
recorded that the unit can play.  
Use media that has data recorded that  
the unit can play.  
Protected File: A copy-protected file is played.  
----  
Demo Mode: The Demonstration mode has been  
selected.  
No Panel:  
E-77:  
The faceplate of the slave unit being  
connected to this unit has been removed.  
Replace it.  
Hold down button [5] and press  
the Reset button to release the  
Demonstration mode.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
"E-77" code does not disappear, consult  
your nearest service center.  
Mecha Error: Something is wrong with the disc  
magazine. Or the unit is malfunctioning for  
some reason.  
Check the disc magazine. And then  
press the reset button on the unit. If the  
"Mecha Error" code does not disappear,  
consult your nearest service center.  
Hold Error:  
The protective circuit in the unit activates  
when the temperature inside the  
automatic disc changer exceeds 60°C  
(140°F), stopping all operation.  
Cool down the unit by opening  
the windows or turning on the air  
conditioner. As the temperature falls  
below 60°C (140°F), the disc will start  
playing again.  
English  
|
45  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
Audio section  
Frequency range (200 kHz space)  
: 87.9 MHz – 107.9 MHz  
Maximum output power  
: 50 W x 4  
Usable sensitivity (S/N = 30dB)  
: 9.3dBf (0.8 µV/75 Ω)  
Full Bandwidth Power (at less than 1% THD)  
: 22 W x 4  
Quieting Sensitivity (S/N = 50dB)  
: 15.2dBf (1.6 µV/75 Ω)  
Tone action  
Bass : 100 Hz 8 dB  
Frequency response ( 3 dB)  
Middle : 1 kHz 8 dB  
Treble : 12.5 kHz 8 dB  
Preout level / Load (during disc play)  
: 2000 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 70 dB  
Selectivity ( 400 kHz)  
: ≥ 80 dB  
Stereo separation (1 kHz)  
: 40 dB  
Auxiliary input (KDC-MPV8025)  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 100 kΩ  
AM tuner section  
Frequency range (10 kHz space)  
: 530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB)  
: 28 dBµ (25 µV)  
CD player section  
General  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 1 Bit  
Spindle speed  
: 1000 – 400 rpm (CLV 2times)  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 162 mm  
7-3/16 x 2-1/16 x 6-3/8 inch  
Weight  
: 4.19 lbs (1.9 kg)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.01 %  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Dynamic range  
: 93 dB  
Channel separation  
: 95 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
|
46  
English  

Rockford Fosgate FNX2406 User Manual
PYLE Audio PYLE Plus Series PLCDCS330MP User Manual
Philips Car Speaker hts3565d User Manual
Panasonic DMP BDT215 User Manual
Panasonic CQ DF701W User Manual
Orion Car Audio P62 User Manual
Onkyo Car Stereo System CR 425UKD User Manual
Laney Amplification Car Amplifier GC50A User Manual
Kenwood KDC MP232 User Manual
JVC KS FX901 User Manual