Panasonic CQ DF701W User Manual

CD Player/Receiver with Dot Matrix LCD and CD Changer Control  
CQ-DF701W  
REMOTE  
SET/AUTOP  
CQ-DF701W  
OPEN  
;
/
1
MOSFET 50WX4  
BAND  
CHC  
!@  
DISP  
VOL  
MENU  
PSET  
DM  
PWR  
TUNE  
TRACK  
Operating Instructions  
SOURCE  
DISC  
S•HDB  
HDB  
DIM  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
Please read these instructions carefully before using this product and save this manual for future use.  
E
N
G
L
I
E
N
G
L
I
Features  
Remote Control Unit Preparation  
S
H
S
H
Full-dot expressiveness <3D dot matrix display>  
Battery Installation  
Lithium battery  
(included)  
You can select an operation quickly because operation items are shown on the display. You can also enjoy vari-  
ety of actions and direction.  
1 Remove the battery holder.  
1
2
Pull the holder by the position B while pushing posi-  
Back side  
tion A in the direction indicated by the arrow.  
2 Install the battery on the battery holder.  
Audio control functions  
Set a new battery properly with its (i) side facing up  
S HDB (Super High Definition Bass) (page 14)  
as shown in the figure.  
CD changer control (page 20)  
Insert the battery holder.  
Push in the battery holder back into its original posi-  
tion.  
Position B  
3
Anti-theft removable face  
You can remove the face plate when you leave your car. (page 33)  
Battery holder Position A  
Battery Notes  
Remove and dispose of an old battery immediately.  
Battery Information:  
Battery type: Panasonic lithium battery (CR2025) (included)  
Battery life: Approximately 6 months with normal use (at room temperature)  
Caution:  
Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire.  
Battery leakage may damage the unit.  
Before Reading these Instructions  
You can operate this unit by pressing buttons on the main unit and the remote control.  
Do not disassemble or short the battery. Do not throw a battery into a fire.  
Keep batteries away from children to avoid the risk of accidents.  
Be careful to the local disposal rules when you dispose of batteries.  
These instructions describe buttons that are concerned with operations as follows.  
Example: Press [P. SET "] or [P. SET #]/["] or [#].  
REMOTE  
CQ-DF701W  
OPEN  
SET/AUTOP  
; /  
1
MOSFET 50WX  
4
Point the remote control unit at  
the main unit’s sensor (REMOTE).  
[buttons on the main unit]/[remote control]  
BAND  
DISP  
CHC  
!@  
VOL  
MENU  
PSET  
DM  
PWR  
TUNE  
TRACK  
Some operations can be activated by pressing buttons only on main unit or remote control.  
SOURCE  
Those cases are described in the instructions.  
DISC  
S•HDB  
HDB  
DIM  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
Example: Press [D M] on the main unit to select the preset station.  
10  
11  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
General  
S
H
S
H
Open/Close the Front Panel  
1 Power  
Volume  
OPEN: Press [OPEN] on the front panel.  
Turn the key in the ignition until the accessory  
[" VOL]: Up  
3
4
CLOSE: Raise the panel by hand.  
indicator lights.  
[# VOL]: Down  
ACC  
N
O
ON: Press [SOURCE] (PWR).  
OFF: Press [SOURCE] (PWR) again for more  
than 1 second.  
Setting range: 0 to 40  
<
Note:  
After turning off the ignition key, a security  
message is displayed, and the panel remov-  
able alarm that reminds you to take the panel  
is activated.  
The sound level for each source is stored in  
memory.  
(For radio, one volume setting for AM, one  
volume setting for all FMs)  
Close  
(When S-LED is set to ON page 26)  
Note:  
When the power is switched on for the rst time,  
a demonstration message appears on the display.  
To cancel this display, press [DISP].  
REMOTE  
REMOTE  
CQ-DF701W  
OPEN  
CQ-DF701W  
OPEN  
SET/AUTOP  
SET/AUTOP  
; /  
1
; /  
1
MOSFET 50WX  
4
MOSFET 50WX4  
BAND  
CHC  
!@  
DISP  
BAND  
CHC  
!@  
DISP  
VOL  
MENU  
PSET  
VOL  
MENU  
PSET  
DM  
DM  
PWR  
PWR  
TUNE  
TRACK  
TUNE  
TRACK  
SOURCE  
SOURCE  
DISC  
DISC  
SHDB  
HDB  
SHDB  
HDB  
DIM  
DIM  
MUTE  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
2 Source  
Mute/Attenuator  
Press [SOURCE] (PWR) to change the source.  
ON: Press [  
].  
MUTE  
Source  
Radio  
OFF: Press again.  
Decreasing volume range depends on setting.  
(page 26)  
(When a CD is inserted.)  
CD player  
(When a CD changer is connected and  
magazine is in the changer.)  
: No sound.  
CD changer control  
AUX-IN setting  
(When AUX-IN setting is activated.)  
: Decrease the volume to 1/10 .  
(
page 26)  
[SOURCE]  
POWER  
SOURCE  
1
3
2
(POWER)  
RAND  
4
[VOL "]  
VOL  
SCAN REP  
[VOL #]  
5
6
MENU  
SEL  
BAND  
Cautions:  
MUTE  
DISP  
[MUTE]  
To avoid damaging the front panel, do not push it down or place objects on it while it is open.  
Do not pinch your nger or hand in the front panel.  
Do not insert foreign matter into the disc slot.  
Car Audio  
12  
13  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
General  
(Continued)  
S
H
S
H
S HDB  
Display Change  
5
6
(Super High Denition Bass)  
When Power is ON  
Especially for rock music, the bass-sound will be more  
powerful.  
Press [DISP].  
Mode display  
Press [S HDB] on the main unit to change the Super  
High Denition Bass on.  
: Default  
Mode and spectrum analyzer display  
: The bass sounds of the speakers are  
strongly emphasized.  
: The bass sounds of the speakers are  
moderately emphasized.  
(The sounds of the subwoofer can  
be heard clearly.)  
Spectrum analyzer display  
If you press a button, the mode and spectrum analyzer display  
appear for 5 seconds.  
REMOTE  
SET/AUTOP  
CQ-DF701W  
OPEN  
; /  
1
MOSFET 50WX  
4
BAND  
DISP  
CH•  
C
!@  
VOL  
MENU  
P
SET  
D
M  
Mode and clock display  
PWR  
TUNE  
TRACK  
SOURCE  
DISC  
SHDB  
HDB  
DIM  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
Note:  
When S HDB is on, the indicator (S HDB BOOM or TIGHT)  
Display and light off (when it is turned on.)  
is shown on the audio indicator display. (page 15)  
If you press a button, the light is turned on, the mode display  
appears for 5 seconds, and the light is turned off again.  
Dimmer  
Press and hold [DISP] for more than 2 seconds.  
The audio indicator is displayed for 15 seconds and returns to the pre-  
vious display.  
(Display Brightness Setting Range)  
Press [DIM] on the main unit to change the dimmer level.  
When the indicator lights, the audio function (S HDB/SUB W) is now  
activated.  
: Bright  
Default  
Press [DISP] again to cancel.  
POWER  
When Power is OFF  
: Medium  
: Dark  
SOURCE  
1
3
2
Press [DISP].  
Clock display  
RAND  
4
VOL  
SCAN REP  
5
6
MENU  
SEL  
BAND  
Display and light off  
MUTE  
DISP  
[DISP]  
Car Audio  
Notes:  
Set the spectrum analyzer pattern in a separate procedure. (page 24)  
: Displays before adjusting the clock. (page 24)  
14  
15  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Radio  
S
H
S
H
1 Radio Mode  
Radio mode display  
One-Touch Selection of a Preset Station  
Press [SOURCE] to change to the radio mode.  
7
8
Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories.  
2 Band  
1 Select a band and frequency (steps 1, 2 and 3 on the previous  
page).  
Press [BAND] to change the band.  
Source  
FM stereo indicator  
Press and hold [P. SET "] or [P. SET #]/["] or [#] for more than  
2 seconds until the preset number blinks.  
2
FM1  
FM2  
FM3  
AM  
Press [P. SET "] or [P. SET #]/["] or [#] to select a preset num-  
ber.  
3
Manual Preset  
Memory  
Press and hold [P. SET "] or [P. SET #]/["] or [#] for more than  
2 seconds to memorize.  
4
The display blinks once, and a re-  
Manually save a sta-  
ceiving station is saved in the  
tion in the preset  
memory.  
Preset number  
memory  
Note:  
Frequency setting can be performed even after selecting a preset num-  
REMOTE  
CQ-DF701W  
SET/AUTOP  
OPEN  
; /  
1
MOSFET 50WX  
4
BAND  
DISP  
CHC  
!@  
ber.  
VOL  
MENU  
PSET  
DM  
PWR  
TUNE  
TRACK  
Entering Numbers Directly from the Remote Control  
SOURCE  
DISC  
SHDB  
HDB  
DIM  
MUTE  
1 Select a band and frequency (step 1, 2 and 3 on the previous page).  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
Press and hold [1] to [6] on the remote control for more than 2 sec-  
2
onds to memorize.  
Direct Memory  
Your favorite radio station can be memorized in  
3 Tuning  
[TUNE $]/[$]: Up  
[TUNE %]/[%]: Down  
[D M] on the main unit.  
1 Select a band (steps 1 and 2 on the  
Scanning:  
Press and hold [TUNE $] or [TUNE %]/[$] or  
[%] for more than 0.5 seconds, then release.  
Seeking will start.  
previous page).  
Default: FM 87.50 MHz  
2 Press and hold [BAND] (AUTO P) for  
Auto Preset  
Memory  
(AUTO P)  
Memorize  
more than 2 seconds.  
1 Select a band and frequency (steps 1, 2 and  
3).  
The 6 strongest available stations will be automatically saved in the  
memory under preset number 1 to 6.  
2 Press and hold [D M] for more than 2 seconds.  
Frequency blinks once and is saved in the mem-  
ory.  
Once set, the preset stations are sequentially scanned for 5 seconds  
each.  
Press [P. SET "] or [P. SET #]/["] or [#] for the broadcast you  
want to listen to.  
Automatically save  
strong stations in the  
preset memory  
Note:  
The new station is overwritten on existing saved  
stations after following this procedure.  
(Press [1] to [6] on the remote control.)  
POWER  
SOURCE  
1
3
2
[SOURCE]  
RAND  
Note:  
Recalling the Direct Memory  
4
[1] to [6]  
Preset button  
VOL  
SCAN REP  
New stations are overwritten on existing saved stations after following this procedure.  
Press [D M].  
5
6
MENU  
SEL  
["] [#]  
(PRESET  
MEMORY)  
(SELECT)  
1 Select a band (steps 1 and 2 on the previous page).  
[BAND]  
BAND  
Preset Station  
Calling  
2 Press [P. SET "] or [P. SET #]/["] or [#] to select the preset  
Press [D M] again to cancel and return to the previ-  
[%] [$]  
(TUNE)  
number for tuning in the preset station.  
MUTE  
DISP  
ous source.  
Entering Numbers Directly from the Remote Control  
Car Audio  
Note:  
Press [1] to [6] on the remote control.  
You can recall the direct memory when the power  
is off.  
16  
17  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
CD Player  
S
H
S
H
Menu Setting on CD Player Mode  
Disc Insert and Playback  
9
10  
Q-DF701W  
OPEN  
DISP  
1 Press [MENU]/[SEL] (MENU) during CD playing.  
2 Press [P. SET "] or [P. SET #]/["] or [#] to select a submenu.  
MOSFET 50WX  
4
1 Open the front panel.  
CD player menu display  
DM  
Press [OPEN] on the front panel.  
PWR  
SOURCE  
2 Insert the disc.  
3 Press [BAND] (SET) to change the setting.  
(EJECT)  
<
Close the front panel manually.  
Playback will start automatically.  
Notes:  
Operations except setting should be performed after returning to the mode display.  
The display returns to the previous one with no operation for 15 seconds after changing to the menu display.  
Press [DISP] to return to the regular mode.  
<
Close  
When CD is in the player  
Press [SOURCE] to change to CD player mode.  
Play Setting  
Notes:  
Label side  
: All the available tracks plays in a random se-  
quence.  
: Cancel  
ON  
Select  
RAND  
Do not insert a disc when this indicator  
lights.  
Random Play  
Scan Play  
OFF  
CD player mode display  
Loading a CD when the power is off allows the  
power to be turned on.  
Ejecting the CD when the unit is in the CD player  
mode allows the power to be turned off.  
: The rst 10 seconds of each track plays in  
sequence.  
: Cancel  
ON  
Select  
SCAN  
OFF  
Play setting  
Lights when the disc is loaded.  
Blinks when the disc is played.  
: Repeat the current track.  
: Cancel  
ON  
Select  
REP  
Repeat Play  
Stop and Disc Eject  
OFF  
Press [<] (EJECT) to stop CD play and eject the disc.  
Direct setting on the remote control when the menu is not displayed:  
Press [4] (RAND). Press again to cancel.  
Random Play  
Listening to a CD  
Pause  
Press [5] (SCAN). Press again to cancel.  
Scan Play  
Press [6] (REP). Press again to cancel.  
Repeat Play  
CD Player Mode  
[ [  
Press [BAND] ( /1) during CD playing.  
Press [SOURCE] to change to CD player mode and  
POWER  
[ [  
Press [BAND] ( /1) again to cancel.  
playback starts.  
SOURCE  
1
3
2
[SOURCE]  
RAND  
4
[DISP]  
[4] (RAND)  
VOL  
SCAN REP  
5
6
REMOTE  
CQ-DF701W  
OPEN  
[5] (SCAN)  
[6] (REP)  
SET/AUTOP  
; /  
1
MOSFET 50WX  
4
BAND  
DISP  
MENU  
CHC  
!@  
SEL  
[SEL] (MENU)  
[BAND]  
["] [#]  
VOL  
MENU  
PSET  
DM  
PWR  
TUNE  
TRACK  
(MENU SELECT)  
SOURCE  
BAND  
DISC  
SHDB  
HDB  
DIM  
[%] [$] (TRACK)  
MUTE  
MUTE  
DISP  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
[DISP]  
Car Audio  
Track Selection  
Track Search  
Cautions:  
[TRACK 5]/[$]: Next track.  
Press and hold.  
Only 12 cm CD is available for this unit.  
To avoid damaging the front panel, do not push it down or place objects on it while it is open.  
Do not use irregularly shaped CDs (heart-shaped, octagon, etc.).  
[TRACK 6]/[%]: Beginning of the current track.  
[TRACK 5]/[$]: Fast forward  
[TRACK 6]/[%]: Fast backward  
Release to resume the regular play.  
Previous track (Press twice.)  
Do not pinch your nger or hand in the front panel. Do not insert foreign matter into the disc slot.  
18  
19  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
CD Changer  
S
H
S
H
CD changer functions are designed for optional Panasonic CD changer unit.  
Menu Setting on CD Changer Mode  
Preparation:  
11  
12  
Connect the CD changer, and load a magazine (disc).  
Press [MENU]/[SEL] (MENU) during CD changer playing.  
1
CD changer menu display  
Notes:  
Loading a magazine when the power is off allows the power to be turned on.  
Ejecting the magazine when the unit is in the CD changer mode allows the power to be turned off.  
Pausing does not function in the CD changer mode.  
2 Press [P. SET "] or [P. SET #]/["] or [#] to select a submenu.  
3 Press [BAND] (SET) to change the setting.  
Notes:  
1 CD Changer Mode  
Operations except setting should be performed after returning to the mode display.  
The display returns to the previous one with no operation for 15 seconds after changing to the menu display.  
Press [DISP] to return to the regular mode.  
Press [SOURCE] to change to CD changer mode  
and playback starts.  
CD changer mode display  
Play Setting  
Note:  
: All the available tracks on all discs in the maga-  
zine plays in a random sequence.  
: Cancel  
: Load a magazine  
with CDs.  
ON  
Select  
RAND  
Play setting  
OFF  
Lights when the changer (maga-  
zine) is connected.  
Blinks when the disc is played.  
Random Play  
Scan Play  
: All the available tracks on the current disc plays  
in a random sequence.  
: Cancel  
ON  
Select  
2 Disc Selection  
D RAND  
[DISC "]/["]: Next disc.  
OFF  
[DISC #]/[#]: Previous disc.  
[DISP]  
: The rst 10 seconds of each track on the discs  
plays in sequence.  
: Cancel  
ON  
Select  
SCAN  
REMOTE  
CQ-DF701W  
OPEN  
SET/AUTOP  
; /  
1
MOSFET 50WX  
4
BAND  
CHC  
!@  
DISP  
OFF  
VOL  
MENU  
PSET  
DM  
PWR  
TUNE  
TRACK  
SOURCE  
DISC  
SHDB  
: The rst 10 seconds of the rst track of all the  
discs in the magazine plays in sequence.  
: Cancel  
DIM  
ON  
Select  
MUTE  
HDB  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
D SCAN  
OFF  
: Repeat the current track.  
: Cancel  
ON  
Select  
REP  
Track Selection  
Change the CD Changer Unit  
[TRACK 5]/[$]: Next track.  
Press [BAND] (CH C !@) to select the CD chang-  
OFF  
[TRACK 6]/[%]: Beginning of the current track.  
er 1 or 2 mode.  
CD-CH1: CD changer 1 mode  
CD-CH2: CD changer 2 mode  
Repeat Play  
Previous track (Press twice.)  
: Repeat the current disc.  
: Cancel  
ON  
Select  
D REP  
OFF  
Track Search  
Press and hold.  
Direct setting on the remote control when the menu is not displayed:  
[TRACK 5]/[$]: Fast forward  
[TRACK 6]/[%]: Fast backward  
Release to resume the regular play.  
POWER  
Press [4] (RAND). Press again to cancel.  
Random Play  
SOURCE  
1
3
2
[SOURCE]  
RAND  
4
[4] (RAND)  
Press and hold [4] (RAND). Press and hold again to cancel.  
Disc Random Play  
Scan Play  
VOL  
SCAN REP  
5
6
[5] (SCAN)  
[6] (REP)  
MENU  
Press [5] (SCAN). Press again to cancel.  
SEL  
[SEL] (MENU)  
[BAND]  
["] [#]  
(DISC/MENU  
SELECT)  
Press and hold [5] (SCAN). Press and hold again to cancel.  
Press [6] (REP). Press again to cancel.  
BAND  
Caution:  
Disc Scan Play  
Repeat Play  
[%] [$] (TRACK)  
Do not use irregularly shaped CDs (heart-  
shaped, octagon, etc.).  
MUTE  
DISP  
[DISP]  
Car Audio  
Press and hold [6] (REP). Press and hold again to cancel.  
Disc Repeat Play  
20  
21  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Audio Settings  
S
H
S
H
Notes:  
[DISP]  
POWER  
[MENU] [BAND] (SET)  
Audio menu display  
SOURCE  
1
3
2
Operations except setting should be performed after  
returning to the mode display.  
The display returns to the previous one with no op-  
eration for 15 seconds after changing to the menu  
display.  
RAND  
13  
14  
REMOTE  
SET/AUTOP  
CQ-DF701W  
OPEN  
;
/
1
MOSFET 50WX4  
4
BAND  
CHC  
!@  
DISP  
VOL  
MENU  
PSET  
VOL  
DM  
SCAN REP  
PWR  
TUNE  
TRACK  
SOURCE  
5
6
DISC  
SHDB  
HDB  
DIM  
MENU  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
SEL  
[SEL] (MENU)  
[BAND] (SET)  
["] [#]  
(MENU  
Press [DISP] to return to the regular mode.  
BAND  
[P.SET "] [P.SET #] [TUNE %] [TUNE $]  
SELECT)  
[%] [$]  
MUTE  
DISP  
(BAS/TRE/BAL/  
FAD/LEVEL/LPF)  
[DISP]  
(MENU SELECT)  
(BAS/TRE/BAL/FAD/  
LEVEL/LPF)  
Car Audio  
1 Menu  
2 Submenu  
3 Setting  
Press [TUNE $] or [TUNE %]/[$] or [%] to select BAS or TRE.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Bass and Treble  
You can adjust the bass and treble  
sound.  
Default: BAS (Bass) 0 dB  
TRE (Treble) 0 dB  
Setting range: j12 dB to i12 dB  
by 3 dB step  
BAS (Bass)  
TRE (Treble)  
[P. SET "]/["]: Increase the bass.  
[P. SET "]/["]: Increases the treble.  
BAS/TRE  
Press [BAND] (SET) to  
[P. SET #]/[#]: Decreases the bass.  
[P. SET #]/[#]: Decreases the treble.  
set.  
Press [BAND] (SET) to set.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Balance and Fader  
BAL (Balance)  
FAD (Fader)  
Press [MENU]/  
You can adjust the sound balance among  
the front, rear, right and left speakers.  
Default: BAL (Balance) Center  
FAD (Fader) Center  
[TUNE $]/[$]: Right enhanced.  
[P. SET "]/["]: Front enhanced.  
[SEL] (MENU) to select  
AUDIOon the menu  
display.  
BAL/FAD  
Press [BAND] (SET) to  
[TUNE %]/[%]: Left enhanced.  
[P. SET #]/[#]: Rear enhanced.  
Setting range: 15 levels each  
Press [BAND] (SET) to set.  
Regular mode  
display  
set.  
AUDIO  
PICTURE  
FUNCTION  
Press [P. SET "] or [P. SET #]/["] or [#] to select LEVEL or LPF.  
Subwoofer Level  
When the subwoofer is activated, you  
can change the subwoofer volume level.  
LEVEL  
[TUNE $]/[$]: Increase the level.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Default: 4  
Setting range: 0 (MUTE) to 8  
[TUNE %]/[%]: Decrease the level.  
Press [BAND] (SET) to set.  
SUB WOOFER  
Note:  
When subwoofer level is set 0, the indicator  
Press [BAND] (SET) to  
set.  
Cut-off Frequency Control  
The maximum lower frequency level can  
be adjusted to match your subwoofer and  
the acoustics inside your car.  
LPF  
(SUB W) is not shown on the audio indicator  
Press [TUNE $] or [TUNE %]/[$] or [%] to select  
display. (page 15)  
120 Hz or 80 Hz.  
Press [BAND] (SET) to set.  
Default: 120 Hz  
Setting range: 120 Hz/80 Hz  
22  
23  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Picture (Display) Settings  
S
H
S
H
Notes:  
[MENU] [BAND] (SET)  
[DISP]  
POWER  
Display menu display  
SOURCE  
1
3
2
Operations except setting should be performed after  
returning to the mode display.  
The display returns to the previous one with no op-  
eration for 15 seconds after changing to the menu  
display.  
RAND  
15  
16  
REMOTE  
CQ-DF701W  
OPEN  
SET/AUTOP  
;
/
1
MOSFET 50WX4  
BAND  
CHC  
!@  
DISP  
4
VOL  
MENU  
PSET  
DM  
VOL  
SCAN REP  
PWR  
TUNE  
TRACK  
SOURCE  
5
6
DISC  
SHDB  
HDB  
DIM  
MUTE  
MENU  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
SEL  
["] [#]  
(MENU  
[SEL] (MENU)  
[BAND] (SET)  
Press [DISP] to return to the regular mode.  
BAND  
SELECT/  
[P.SET "] [P.SET #]  
(MENU SELECT/CLOCK ADJ)  
[TUNE %] [TUNE $]  
(S A PATTERN/  
(S A PATTERN/  
[%] [$]  
CLOCK ADJ)  
MUTE  
DISP  
CONTRAST/  
CLOCK ADJ)  
CONTRAST/CLOCK ADJ)  
Car Audio  
[DISP]  
1 Menu  
2 Submenu  
3 Setting  
Press [TUNE $] or [TUNE %]/[$] or [%] to select the pattern.  
: Display showing a cube that continues to  
change  
: Display showing a bird apping its wings  
A
B
C
D
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Spectrum Analyzer (S A)  
Display Pattern  
Default: Pattern A  
Variety: 6 types  
: Display showing a globe that continues  
to change  
: Display showing the image of a circuit  
E
S A PATTERN  
: Display showing a ower or doll pattern  
: Standard spectrum analyzer display  
(9 bands)  
STD  
Press [BAND] (SET) to  
set.  
Press [BAND] (SET) to set.  
Note:  
Change the display to show the spectrum analyzer display. (page 15)  
Press [MENU]/  
[SEL] (MENU) to select  
PICTUREon the  
menu display.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Contrast  
Allows you to adjust the display contrasts  
for better viewing.  
[TUNE $]/[$]: level up  
[TUNE %]/[%]: level down  
Regular mode  
display  
CONTRAST  
Press [BAND] (SET) to  
set.  
Default: Level 3  
Setting range: Level 1 to level 5  
Press [BAND] (SET) to set.  
AUDIO  
PICTURE  
FUNCTION  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Press [BAND] (SET)  
to select  
Clock display  
Clock on the Mode Display  
Default: ON  
: Clock display ON  
: Clock display OFF  
ON  
CLOCK-OFF  
CLOCK-ON  
(--:--will appear before adjust-  
ing the clock.)  
OFF  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Hour/Minute Switch  
Hour/Minute Adjustment  
Clock Adjustment  
[TUNE %]/[%]: The hour display high lights.  
[P. SET "]/["]: Put forward hour/minute.  
(12 hour system)  
Default: Not adjusted.  
CLOCK ADJ  
Press [BAND] (SET) to  
[TUNE $]/[$]: The minutes display high lights.  
[P. SET #]/[#]: Put back hour/minute.  
Press [BAND] (SET) to set.  
set.  
24  
25  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
User Settings  
S
H
S
H
Notes:  
POWER  
[MENU] [BAND] (SET)  
[DISP]  
SOURCE  
1
3
2
Function menu display  
Operations except setting should be performed after  
returning to the mode display.  
The display returns to the previous one with no op-  
eration for 15 seconds after changing to the menu  
display.  
RAND  
17  
18  
REMOTE  
CQ-DF701W  
OPEN  
SET/AUTOP  
;
/
1
MOSFET 50WX4  
4
BAND  
CHC  
!@  
DISP  
VOL  
MENU  
PSET  
VOL  
SCAN REP  
DM  
PWR  
TUNE  
TRACK  
SOURCE  
5
6
DISC  
SHDB  
HDB  
DIM  
MENU  
MUTE  
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY  
SEL  
[SEL] (MENU)  
[BAND] (SET)  
["] [#]  
(MENU  
Press [DISP] to return to the regular mode.  
BAND  
[P.SET "] [P.SET #]  
SELECT)  
MUTE  
DISP  
(MENU SELECT)  
[DISP]  
Car Audio  
1 Menu  
2 Submenu  
3 Setting  
Press [BAND] (SET) to switch between MUTE (mute) or ATT (attenuator) in turn.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
Mute/Attenuator  
You can select how much to lower the  
: No sound.  
MUTE  
ATT  
: Decrease the volume to 1/10.  
volume when [MUTE] is pressed.  
MUTE KEY  
Default: MUTE  
Press [MENU]/  
Press [BAND] (SET) to activate the function or inactivate it in turn.  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
[SEL] (MENU) to select  
FUNCTIONon the  
menu display.  
: External input (AUX-IN) is selectable as a source.  
: External input (AUX-IN) is not selectable as a source.  
ON  
Excluding AUX-IN from  
Source Selection  
Default: ON  
OFF  
AUX-IN  
Regular mode  
display  
With AUX-IN set to OFF, AUX-IN will not be selected when [SOURCE] is pressed.  
(page 12)  
AUDIO  
PICTURE  
FUNCTION  
Press [BAND] (SET) to activate the function or inactivate it in turn.  
: Security function is active.  
ON  
Press [P. SET "] or  
[P. SET #]/["] or [#]  
to select  
: Security function is non-active.  
OFF  
Security Function  
Security Function  
Default: ON  
S-LED  
When the key in the ignition is turned OFF.  
Security message will be active.  
Security message display  
The panel removable alarm will be active.  
When the removable face plate is removed.  
The security indicator blinks. (page 33)  
26  
27  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Installation Guide  
S
H
S
H
If your car is not wired for an audio unit:  
Go to the fuse block and find the fuse port for the  
battery, usually marked BAT.  
Identify All Leads  
The first step in installation is to identify all the car  
wires you’ll use when hooking up your sound sys-  
tem.  
19  
20  
WARNING  
Speakers  
This installation information is designed for experienced installers and is not in-  
tended for non-technical individuals. It does not contain warnings or cautions of po-  
tential dangers involved in attempting to install this product.  
As you identify each wire, we suggest that you label  
it using masking tape and a permanent marker.  
This will help avoid confusion when making con-  
nections later.  
Identify the car speaker leads. There are two leads  
for each speaker which are usually color coded.  
A handy way to identify the speaker leads and the  
speaker they are connected with is to test the leads  
using a 1.5 V AA battery as follows.  
Hold one lead against one pole of the battery and  
stroke the other lead across the other pole. You will  
hear a scraping sound in one of the speakers if you  
are holding a speaker lead.  
Any attempt to install this product in a motor car by anyone other than qualified in-  
staller could cause damage to the electrical system and could result in serious per-  
sonal injury or death.  
Note:  
Do not connect the power connector to the stereo  
unit until you have made all connections. If there  
are no plastic caps on the stereo hooking wires,  
insulate all exposed leads with electrical tape until  
you are ready to use them. Identify the leads in  
the following order.  
If you encounter problems, please consult your  
nearest professional installer.  
Installation Hardware  
If not, keep testing different lead combinations until  
you have located all the speaker leads. When you  
label them, include the speaker location for each.  
No.  
Item  
Diagram Qty  
Caution:  
1
Mounting collar  
1
Power Lead  
This unit operates with a 12 V DC negative  
ground auto battery system only. Do not at-  
tempt to use it in any other system. Doing so  
could cause serious damage.  
Antenna Motor  
If your car has a radio or is pre-wired for one:  
Cut the connector wires one at a time from the plug  
(leaving the leads as long as possible) so that you  
can work with individual leads.  
If your car is equipped with an automatic power an-  
tenna, identify the car motor antenna lead by con-  
necting one bulb tester lead to the car battery lead  
and touching the remaining exposed wires from the  
cut radio connector plug one at a time. You will  
hear the antenna motor activate when you touch  
the correct wire.  
2
3
4
5
6
7
8
Hex. nut (5 mm·)  
1
1
1
1
1
1
1
Before you begin installation, look for the items  
which are packed with your unit.  
Rear support strap  
Tapping screw  
(5 mm·a16 mm)  
Panasonic Servicenter for Service Directory  
Keep for future reference in case the product  
needs servicing.  
Installation HardwareNeeded for in-dash in-  
stallation.  
Antenna  
Turn the ignition on to the accessory position, and  
ground one lead of the test bulb to the chassis.  
Mounting bolt (5 mm·)  
The antenna lead is a thick, black wire with a metal  
plug at the end.  
Touch the other lead of the test bulb to each of the  
exposed wires from the cut radio connector plug.  
Touch one wire at a time until you find the outlet  
that causes the test bulb to light.  
Power connector  
Connect All Leads  
Now that you have identified all the wires in the car,  
you are ready to begin connecting them to the  
stereo unit wires. The wiring diagram (pages  
34j35) shows the proper connections and color  
coding of the leads.  
Required Tools  
Removable face plate  
case  
You’ll need a screwdriver, a 1.5 V AA battery, and  
the following:  
Now turn the ignition off and then on. If the bulb  
also turns off and on, that outlet is the car power  
lead.  
Trim plate  
12 V DC  
Test bulb  
Electrical  
tape  
Side-cut  
pliers  
We strongly recommend that you test the unit be-  
fore making a final installation.  
You can set the unit on the floor and make tempo-  
rary connections to test the unit. Use electrical tape  
to cover all exposed wires.  
If your car is not wired for an audio unit:  
Go to the fuse block and find the fuse port for radio  
(RADIO), accessory (ACC), or ignition (IGN).  
Overview  
This product should be installed by a professional.  
However, if you plan to install this product yourself,  
your first step is to decide where to install it. The  
instructions in these pages will guide you through  
the remaining steps:  
Battery Lead  
If your stereo unit has a yellow lead, you will need  
to locate the car’s battery lead. Otherwise you may  
ignore this procedure. (The yellow battery lead pro-  
vides continuous power to maintain a clock, memo-  
ry storage, or other function.)  
Important:  
Dashboard Specifications  
Thickness  
Connect the red power lead last, after you  
have made and insulated all other connec-  
tions.  
Min. 4.75 mm  
Max. 5.56 mm  
(Please refer to the “ WARNINGstatement  
above.)  
Identify and label the car wires.  
Connect the car wires to the wires of the power  
connector.  
Install the unit in the dashboard.  
Check the operation of the unit.  
53 mm  
If your car has a radio or is pre-wired for one:  
With the ignition and headlights off, identify the car  
battery lead by grounding one lead of the test bulb  
to the chassis and checking the remaining exposed  
wires from the cut radio connector plug.  
Ground  
Connect the black ground lead of the power con-  
nector to the metal car chassis.  
182 mm  
28  
29  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Installation Guide  
(Continued)  
S
H
S
H
Speakers  
Final Checks  
Installation Procedures  
First complete the electrical connections, and  
then check them for correctness. (pages  
34j35)  
Connect the speaker wires. See the wiring diagram  
(pages 34j35) for the proper hookups. Follow  
the diagram carefully to avoid damaging the speak-  
ers and the stereo unit.  
The speakers used must be able to handle more  
than 50 W of audio power. If using an optional  
audio amplifier, the speakers should be able to han-  
dle the maximum amplifier output power. Speakers  
with low input ratings can be damaged. Speaker  
impedance should measure 4–8 , which is typi-  
cally marked on most speakers. Lower or higher  
impedance speakers will affect output and can  
cause both speaker and stereo unit damage.  
1. Make sure that all wires are properly connected  
and insulated.  
Insert mounting collar 1into the dashboard, and  
bend the mounting tabs out with a screwdriver.  
21  
22  
1
2. Make sure that the stereo unit is securely held in  
the mounting collar.  
3. Turn on the ignition to check the unit for proper  
operation.  
Make sure that the lock lever (§) is ush with the  
mounting collar 1 (not projecting outward).  
Lock lever (§)  
If you have difficulties, consult your nearest author-  
ized professional installer for assistance.  
Preparation  
We strongly recommend that you wear gloves  
for installation work to protect yourself from  
injuries.  
When bending the mounting tabs of the  
mounting collar with a screwdriver, be careful  
not to injure your hands and fingers.  
Motor Antenna  
Connect the car motor antenna lead to the dark  
blue motor antenna relay control lead.  
Lock lever (§)  
6 Power connector  
Battery  
Connect the yellow battery lead to the correct radio  
wire or to the battery fuse port on the fuse block.  
-
Disconnect the cable from the negative battery  
Mounting tabs  
5 Mounting bolt  
terminal (see caution below).  
Antenna  
Unit should be installed in a horizontal position  
with the front end up at a convenient angle, but  
not more than 30o.  
Connect the antenna by plugging the antenna lead  
into the antenna receptacle.  
Secure the rear of the unit.  
2
5
After xing mounting bolt  
and power connector  
6
, x the rear of the unit to the car body by either  
Equipment  
method (a) or (b) shown below.  
Insert trim plate 8.  
Connect any optional equipment such as an ampli-  
er, according to the instructions furnished with  
the equipment. Leave about 30 cm of distance be-  
tween the speaker leads/amplifier unit and the an-  
tenna/antenna extension cord. Read the operating  
and installation instructions of any equipment you  
will connect to this unit.  
3
4
Less than 30x  
After installation, reconnect the negative - bat-  
tery terminal.  
Caution:  
Power  
Do not disconnect the battery terminals of a  
car with a trip or navigational computer since  
all user settings stored in memory will be lost.  
Instead take extra care with installing the unit  
to prevent shorts.  
Connect the red power lead to the correct car radio  
wire or to the appropriate fuse port on the fuse  
block.  
If the stereo unit functions properly with all these  
connections made, disconnect the wires and pro-  
ceed to the final installation.  
(a) Using the rear support strap 3  
(b) Using the rubber cushion (option)  
Fire wall of car  
Dashboard Installation  
Installation Opening  
Rear support bracket  
(provided on the car)  
4 Tapping screw  
Rubber cushion (option)  
(5 mm·a16 mm)  
3 mm·  
Final Installation  
2 Hex. nut  
53 mm  
Lead Connections  
(5 mm·)  
182 mm  
Connect all wires, making sure that each connec-  
tion is insulated and secure. Bundle all loose wires  
and fasten them with tape so they will not fall down  
later. Now insert the stereo unit into the mounting  
collar.  
3 Rear support  
5 Mounting bolt  
strap  
This unit can be installed in any dashboard having  
an opening as shown above. The dashboard should  
be 4.75 mmj5.56 mm thick in order to be able to  
support the unit.  
(5 mm·)  
5 Mounting bolt  
(5 mm·)  
1 Mounting collar  
Congratulations! After making a few final checks,  
you’re ready to enjoy your new auto stereo system.  
1 Mounting collar  
30  
31  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Installation Guide  
(Continued)  
Anti-Theft System  
S
H
S
H
This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.  
The security indicator will blink.  
Remove the Unit  
Switch off the power of the unit.  
23  
24  
Place the Removable Face  
Plate into Case  
1 Switch off the power of the unit.  
2 Remove the removable face plate. (page 32)  
3 Gently press the button of the case and open  
the cover. Place the face plate into the case and  
take it with you when you leave the car.  
Remove the removable face plate.  
1 Press [OPEN]. The removable face plate will  
1 Open  
1
Main unit  
Contact  
2 Push  
7 Removable face plate case  
be opened.  
<
OPEN  
[OPEN]  
MOSFET 50WX  
4
DISP  
DM  
PWR  
3 Pull out  
SOURCE  
2 Push the face plate to the left.  
3 Pull it out toward you.  
Install Removable Face Plate  
Contact  
2Remove the trim plate 8with a screwdriver.  
1 Fit the face plate with its left hole on one of the  
8 Trim plate  
pins provided on the main unit.  
2 Fit the other hold on the other pin applying  
<
Screwdriver  
slight pressure.  
2
<
3
3 Move the face plate up and down a few times to  
make sure it is secure. Then close the front  
panel and press down the right side of the face  
plate until it clicks into plate.  
1
Pull out the unit while pushing down the lock  
lever with a screwdriver.  
Lock lever  
3
Security Indicator  
The security indicator blinks when the removable  
face plate is removed from the unit.  
Security indicator  
Lock lever  
Active the security function in the function menu  
<
display. (page 26)  
<
Panel Removal Alarm  
This alarm sounds to warn you not to forget to re-  
move the panel before leaving your car. This func-  
tion is activated when the security indicator is on.  
Cautions:  
This face plate is not water-proof. Do not expose it to water or excessive moisture.  
Do not remove the face plate while driving your car.  
Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.  
Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical  
contacts.  
4Remove the unit pulling with both hands.  
If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.  
To avoid damaging the front panel, do not push it down or place objects on it while it is open.  
32  
33  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Electrical Connections  
Accessory used for wiring  
Cautions:  
No.  
Item  
Qty  
This product is designed to operate of a 12 V DC, negative ground battery system.  
To prevent damage to the unit, be sure to follow the connection diagram below.  
Remove approx. 5 mm of protective covering from the ends of the leads before connecting.  
Do not insert the power connector into the unit until the wiring is completed.  
Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables  
and keep cable terminals free from touching any metal parts.  
25  
26  
6
Power connector  
1
Remember, if your car has a drive computer or a navigation computer, the data of its memory may be  
erased when the battery terminals are disconnected.  
All other installation methods require the use of dedicated metal ttings. Consult with a qualied servicing  
engineer or your dealer if other method are required.  
CD changer input cord  
(R) (Red)  
Wiring Diagram  
CD.C-IN  
(L) (White)  
(R) (Red)  
CQ-DF701W  
AUX input cord  
AUX-IN  
FRONT  
(L) (White)  
(R) (Red)  
Preout cord (Front)  
(L) (White)  
Antenna  
(R) (Red)  
Preout cord (Rear)  
Subwoofer cord  
6
Power connector  
REAR  
(L) (White)  
CD changer control connector  
(Red)  
S.W-OUT  
(MONO)  
(White)  
Antenna control lead  
To the auto antenna control  
power lead of the car. (Max. 500 mA)  
(White)  
(Blue)  
+
(Left)  
Front speaker lead  
(White/black stripe)  
-
+
FRONT SP  
To front sepaker  
Dual CD changer control lead  
Note:  
(Gray)  
(Brown/white stripe)  
(Right)  
Insulate the dual CD changer control lead with  
vinyl tape when you do not connect it.  
-
+
(Gray/black stripe)  
External amplifier control power lead  
To an external amplifier. (Max. 500 mA)  
(Blue/white stripe)  
Registor (1 k)  
(Green)  
ACC power lead  
To ACC power, _12 V DC.  
ACC  
(Red)  
(Left)  
Rear speaker lead  
(Green/black stripe)  
Fuse (15 A)  
-
+
REAR SP  
To rear sepaker  
Battery lead  
To the battery, continuous _12 V DC.  
BATTERY 15 A  
(Violet)  
(Right)  
(Yellow)  
-
(Violet/black stripe)  
Ground lead  
To a clean, bare metallic part of the car chassis.  
(Black)  
34  
35  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Electrical Connections  
(Continued)  
Troubleshooting  
S
H
S
H
Upgrading the System  
Cautions:  
Preliminary Steps  
Do not use the unit if it malfunctions or  
is something wrong.  
Check and take steps as described in the tables below.  
27  
28  
Example Combination  
CD changer (CX-DP88U/N)  
Stereo power amplier  
Do not use the unit in abnormal condi-  
tion, for example, without sound, or  
with smoke or foul smell, can cause ig-  
nition or electric shock. Immediately  
stop using it and call the store where  
you purchased it.  
If You Suspect Something Wrong  
Immediately switch power off.  
Disconnect the power connector and check that there is nei-  
ther smoke nor heat from the unit before asking for repairs.  
Never try to repair the unit yourself because it is dangerous to  
do so.  
Note:  
For wiring, carefully read the operating instructions for the devices connected.  
Ground lead  
CD changer  
CX-DP88U/N  
Troubleshooting Tips  
Common  
Trouble  
Cause/Step  
Cars engine switch is not on.  
Turn your cars ignition switch to ACC or ON.  
Extension cord  
(supplied for CX-DP88U/N)  
Cables are not correctly connected.  
Connect cables correctly.  
Battery cable is not correctly connected.  
Connect the battery cable to the terminal that is always live.  
(R) (Red)  
No power.  
Accessory cable is not correctly connected.  
CD.C-IN  
Connect the accessory cable to your cars ACC source.  
(L) (White)  
Grounding wire is not correctly connected.  
Connect the grounding wire to a metal part of the car.  
S.W-OUT  
Fuse is burnt.  
Call the store where you purchased the unit, or your nearest service  
station and ask for fuse replacement.  
BATTERY  
CQ-DF701W  
(Fuse 3 A)  
Mute is set to ON.  
(L)  
(White)  
(R)  
(Red)  
Set it to OFF.  
DIN cord  
Cables are not correctly connected.  
Connect cables correctly.  
No sound.  
Condensation (dew)  
Wait for a while before use.  
CD changer control  
connector  
The display shows display and light off.  
Press [DISP] to change the display.  
Only sound, no display.  
Noise.  
A mobile phone is used near the unit.  
Keep the mobile phone away from the unit.  
Stereo power  
amplifier  
Buttons unusable.  
Audio sound is not  
matched on the  
mode display.  
Demonstration mode is ON.  
Press [DISP] to cancel demonstration mode.  
Subwoofer speakers  
36  
37  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Troubleshooting  
(Continued)  
Radio  
Sound Setting  
29  
30  
Trouble  
Cause/Step  
Trouble  
Cause/Step  
Station is too far, or signals are too weak.  
Select other stations of higher signal level.  
Left and right balance, or front and rear balance is off on one side.  
Adjust BAL/FAD mode as appropriate.  
No sound from left,  
right, front or rear  
speakers.  
Much noise in FM stereo  
and monaural broad-  
casts.  
Cables are not correctly connected.  
Connect the cables correctly.  
The radio antenna is not extended enough.  
Set the radio antenna enough.  
Battery cable is not correctly connected.  
Connect the battery cable to the terminal that is always live.  
Left and right sounds are  
reversed in stereo lis-  
tening.  
The right speaker wire is connected to the left speaker and the left  
speaker wire to the right speaker.  
Connect the speaker wires to the correct ones.  
Preset station is reset.  
CD  
Remote Control  
Trouble  
Cause/Step  
Trouble  
Cause/Step  
CD is upside down.  
Place CD in the correct direction, and the label side up.  
CD is in the CD compart-  
ment but no sound is  
made, or CD is ejected  
automatically.  
Battery poles (i) (j) are reversed.  
Insert the battery correctly.  
CD is dirty.  
Clean CD, referring to the section on Notes on CD.  
Wrong the battery.  
Check the battery.  
Buttons are invalid for  
operation.  
8 cm disc is ejected automatically.  
The battery has run down.  
Replace the battery.  
CD sound skips, tone  
quality is low.  
CD is dirty.  
Clean CD, referring to the section on Notes on CD.  
Remote control is in the wrong direction.  
Direct the remote control at sensor (REMOTE) on the panel.  
Mounting angle is over 30o.  
Adjust mounting angle to less than 30o.  
Sound skips due to vi-  
bration.  
Instable mounting.  
Mount the unit securely with the mounting parts, referring to the  
section on installation.  
CD is defective.  
Mechanical trouble.  
CD is not ejected.  
Press [OPEN] to open the panel and press [<] (EJECT). If normal  
operation is not restored yet, call the store where you purchased  
the unit or the nearest service station to ask for repairs.  
38  
39  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Troubleshooting  
(Continued)  
S
H
S
H
Error Display Messages  
31  
32  
CD Changer  
CD  
Display  
Cause/Step  
Display  
Cause/Step  
Disc is dirty, or is upside down.  
Disc has scars.  
Disc is dirty, or is upside down.  
Disc has scars.  
Check disc. (The changer automatically switches to the next disc.)  
Press [OPEN] to open the front panel and press [<] (EJECT).  
Check disc.  
After  
5 seconds.  
Load the disc again.  
POWER OFF  
After  
5 seconds.  
No operation by some cause.  
POWER OFF  
If normal operation is not restored yet, call and ask for repairs.  
The display continues if you cannot switch off the power.  
POWER OFF  
No operation by some cause.  
After  
5 seconds.  
Press [OPEN] to open the front panel and press [<] (EJECT).  
Check disc.  
Load the disc again.  
No disc is in the changer (magazine).  
Insert discs into the changer (magazine).  
Note:  
After  
5 seconds.  
For details, refer to operating instructions for the changer used.  
POWER OFF  
Maintenance  
Your product is designed and manufactured to ensure a minimum of maintenance. Use a soft cloth for routine  
exterior cleaning. Never use benzine, thinner or other solvents.  
Product Servicing  
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest au-  
thorized Panasonic Servicenter. The product should be serviced only by a qualied technician.  
Replacing the Fuse  
Use fuses of the same specied rating (15 A). Using different substitutes or fuses with higher ratings, or con-  
necting the unit directly without a fuse, could cause re or damage to the stereo unit.  
If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.  
40  
41  
CQ-DF701W  
CQ-DF701W  
E
N
G
L
I
E
N
G
L
I
Maintenance  
Specications  
S
H
S
H
General  
Power supply:  
Care of the Unit  
34  
12 V DC (11 Vj16 V), test voltage 14.4 V, negative ground  
33  
Cleaning this Unit  
Caution on Cleaning  
Current consumption:  
Maximum power output:  
Tone adjustment range:  
Bass:  
Less than 2.2 A (CD play mode; 0.5 Wa4 channels)  
50 Wa4 channels at 1 kHz, Volume control maximum  
Use a dry, soft cloth to wipe.  
Never use solvents such as benzine, thinner as they  
may mar the surface of the unit.  
n12 dB at 100 Hz  
Treble:  
n12 dB at 10 kHz  
Suitable speaker impedance: 4j8 ≠  
Pre-Amp output voltage:  
Subwoofer output voltage:  
5.0 V (CD play mode; 1 kHz, 0 dB)  
5.0 V  
Notes on CD  
Pre-Amp output impedance: 60 ≠  
Subwoofer output impedance:60 ≠  
ONLY USE DISCS CARRYING THE LABEL  
Dimensions (WaHaD):  
178a50a150 mm  
Weight:  
1.6 kg  
FM Stereo Radio  
How to hold the CD  
Frequency range:  
87.50 MHzj108.00 MHz  
11.0 dBf. (1.25 ¨V, 75 )  
15.2 dBf. (1.6 ¨V, 75 )  
30 Hzj15 kHz (n3 dB)  
Do not touch the underside of the disc.  
Do not make scratches on the discs.  
Do not bend disc.  
Usable sensitivity:  
50 dB quieting sensitivity:  
Frequency response:  
Label side  
When not in use, keep CD in the case.  
Alternate channel selectivity: 75 dB  
Stereo separation:  
Image response ratio:  
IF response ratio:  
Signal/noise ratio:  
35 dB (1 kHz)  
75 dB  
100 dB  
70 dB  
Do not use irregular shaped CDs.  
AM Radio  
Frequency range:  
Usable sensitivity:  
Do not leave discs on the following places:  
Direct sunlight  
Near car heaters  
531 kHzj1 602 kHz  
28 dB/¨V (25 ¨V, S/N 20 dB)  
Do not use irregular shaped CDs.  
Dirty, dusty and damp areas  
Seats and dashboards  
CD Player  
Sampling frequency:  
DA converter:  
<Right>  
<Wrong>  
8 times oversampling  
MASH 1 bit/4 DAC system  
Panasonic super decoding algorithm  
Astigma 3-beam  
Error correction system:  
Pick-up type:  
Disc cleaning  
Use a dry, soft cloth to wipe from the center outward.  
Light source:  
Wave length:  
Semiconductor laser  
780 nm  
Rough edge  
Frequency response:  
Signal/noise ratio:  
Total harmonic distortion:  
Wow and utter:  
Channel separation:  
20 Hzj20 kHz (n1 dB)  
96 dB  
0.01 % (1 kHz)  
Below measurable limits  
75 dB  
Caution on new discs  
A new disc may have rough edges on its inner and outer  
perimeter. These may cause malfunction.  
Remove the rough edges using a pencil, etc.  
Note:  
Specications and the design are subject to modication without notice due to improvements in technology.  
Rough edge  
42  
43  
CQ-DF701W  
CQ-DF701W  

PYLE Audio PLDBT30U User Manual
Philips SWW1810 User Manual
Philips DMP BD65 User Manual
Philips 202P User Manual
Philips 166V3L User Manual
Philips 21PT9467 User Manual
Olympus PT E02 User Manual
Olympus FL 20 User Manual
Kicker DS400 User Manual
Kenwood KVT 536DVD User Manual