CD-RECEIVER
KDC-V6090R
KDC-6090R
KDC-5090R
INSTRUCTION MANUAL
COMPACT
DIGITAL AUDIO
B64-1873-00 (EN)
Safety precautions
IMPORTANT INFORMATION
About the disc changer to be
connected:
To connect a disc changer having the "O-N"
switch to this unit, set the "O-N" switch to
"N".
When you connect a model with no "O-N"
switch, the converter cord CA-DS100
available as an option may be required. For
details, consult your Kenwood dealer.
If a model with no "O-N" switch is
connected, some unavailable functions and
information that cannot be displayed are
generated, such as the DNPS, DNPP,
Magazine random play, and CD Text display.
Note that none of the KDC-C100, KDC-C302,
C205, C705, and non-Kenwood CD changers
can be connected.
2WARNING
2CAUTION
To prevent injury and/or fire, take the
following precautions:
• Insert the unit all the way until it is fully
locked in place. Otherwise it may fly out of
place during collisions and other jolts.
• When extending the ignition, battery or
ground cables, make sure to use
automotive-grade cables or other cables
with an area of 0.75mm (AWG18) or more
to prevent cable deterioration and damage
to the cable coating.
• To prevent short circuits, never put or leave
any metallic objects (e.g., coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not open the top or bottom covers of
the unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or
humidity. Also avoid places with too much
dust or the possibility of water splashing.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
2
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse
with the wrong rating may cause your unit
to malfunction.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it
to strong shock.
The unit may break or crack because it
contains glass parts.
• Do not touch the liquid crystal fluid if the
LCD is damaged or broken due to shock.
The liquid crystal fluid may be dangerous to
your health or even fatal.
2CAUTION
• To prevent short circuits when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• During installation, do not use any screws
except for the ones provided. The use of
improper screws might result in damage to
the main unit.
• Do not apply excessive force to the moving
faceplate. Doing so will cause damage or
malfunction.
You can damage both your unit and
the CD changer if you connect them
incorrectly.
Do Not Load 8-cm (3-in.) CDs in the
CD slot
If you try to load an 8-cm CD with its adapter
into the unit, the adapter might separate
from the CD and damage the unit.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
• Do not apply excessive force to the open
faceplate or place objects on it. Doing so
will cause damage or breakdown.
— 3 —
Safety precautions
• The illustrations of the display and the
panel appearing in this manual are
examples used to explain more clearly how
the controls are used. Therefore, what
appears on the display in the illustrations
may differ from what appears on the
display on the actual equipment, and some
of the illustrations on the display may
represent something impossible in actual
operation.
NOTE
• If you experience problems during
installation, consult your Kenwood dealer.
• Press the reset button if the CD auto
changer is first controlled and operates
incorrectly. The original operating condition
will return.
Egnlish
• The functions that can be used and the
information that can be displayed will differ
depending on the external disc players
being connected.
Reset button
• Characters in the LCD may become difficult
to read in temperatures below 41 ˚F (5 ˚C).
• We strongly recommend the use of the
Code Security function (see p.28) to prevent
theft.
— 4 —
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
Cleaning the CD Slot
As dust can accumulate in the CD slot, clean
it occasionally. Your CDs can get scratched if
you put them in a dusty CD slot.
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It
means that the unit is utilizing laser beams
that are of a weaker class. There is no
danger of hazardous radiation outside the
unit.
Lens Fogging
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a whilst,
consult your Kenwood dealer.
— 5 —
Handling Compact discs
Playing a CD that is dirty, scratched
or warped can cause the sound to
skip and the unit to operate
incorrectly, resulting in worsened
sound quality. Take the following
precautions to prevent your CDs from
getting scratched or damaged.
Storing CDs
Checking New CDs for Burrs
• Do not store CDs in areas exposed to
direct sunlight – such as a car seat or
above the fascia panel (dashboard) – or
other hot places.
A CD-R or CD-RW is more susceptible
than a music CD to damage from high
temperatures and humidity, and in some
cases, may become unusable if left in the
car for long periods of time.
When playing a new CD for the first time,
check that there are not any burrs stuck to
the perimeter of the disc or in the central
hole. CDs with burrs stuck on them may not
load properly or may skip whilst playing.
Remove burrs using a ballpoint pen or a
similar utensil.
Egnlish
Handling CDs
• Remove CDs from the unit when not
listening to them for a whilst, and put
them back in their cases. Do not stack
CDs that have been removed from their
cases or prop them against something.
• Do not touch the recorded side of the CD
(i.e., the side opposite the label) when
holding it.
Burrs
Burrs
Cleaning CDs
If a CD has become dirty, wipe it off gently
using a commercially available cleaning cloth
or a soft cotton cloth, starting from the
centre of the disc and moving outward. Do
not clean CDs with conventional record
cleaners, anti- static formulas, or chemicals
such as paint thinner or benzene.
• The reflective film on a CD-R or a CD-RW is
more fragile than that on an ordinary music
CD, and may peel off if scratched. Fingerprints
on a CD-R or CD-RW are also more likely to
cause skipping when the disc is played. For
these reasons, handle the disc very carefully.
Detailed handling instructions will appear on
the CD-R or CD-RW package: read this
information carefully before using the disc.
• Do not stick tape on either side of the CD.
Tape
— 6 —
Do Not Load CD Accessories in Slot
Do Not Use Special Shape CDs
Do Not Use CDs with Sticker on the
Labelled Side
Do not use the CD with the label sticker
stuck on it.
Using such a CD may cause the CD to be
deformed and the sticker to peel off,
resulting in malfunction of the unit.
Do not use commercially available CD
accessories that can be loaded into the CD
slot, such as stabilisers, protective sheets,
or CD cleaning discs, since they can cause
the unit to malfunction.
• Be sure to use round shape CDs only for
this unit and do not use any special shape
CDs. Use of special shape CDs may cause
the unit to malfunction.
Removing the CD
Only remove the CD from the machine in a
horizontal direction. You may damage the
surface of the CD if you try pulling it down
as it ejects.
• Be sure to use CDs with disc mark
only for this unit.
•CD-Rs and CD-RWs which have not
undergone finalization processing cannot
be played. (For more information on
finalization processing, refer to the manual
for your CD-R/CD-RW writing software or
CD-R/CD-RW recorder.) Additionally,
depending on the recording status, it may
prove impossible to play certain CDs
recorded on CD-R or CD-RW.
— 7 —
General features
Power
5 / ∞
Q
SRC / PWR OFF
CLK
Turning on the power:
Press the SRC button.
Egnlish
NOTE
Turn the power on before carrying out the following procedures.
Turning off the power:
Hold down the PWR OFF button for one second or more.
NOTE
ATT/LOUD
DISP
FM
AM/
NF
The status of the Code Security Function (page 28) is displayed
whenever the power is switched on.
"CODE ON" : Security Code has been registered
"CODE OFF" : Security Code has not been registered
Release
button
4
¢
KDC-6090R/KDC-5090R
Clock indicator
Switching Modes
Switching Modes:
Each time you press the SRC button, the mode switches as
follows:
System Q indicator
Speaker Setting indicator
LOUD indicator
▼
ATT indicator
Tuner mode
▼
CD mode
KDC-V6090R
▼
External disc control mode 1
▼
External disc control mode 2 / AUX mode
▼
Standby mode
Selecting the standby mode:
Press the SRC button repeatedly to select to "ALL OFF".
When "ALL OFF" is displayed, the standby mode is turned on.
The standby mode turns all functions off although leaving the
unit’s power on. Use this mode when you want to have the
display illuminated but do not want to listen to anything.
Clock indicator
System Q indicator
ATT indicator
LOUD indicator
Speaker Setting indicator
— 8 —
NOTE
Attenuator
• The mode switches to the next mode from any mode which
cannot be used.
• The external disc control mode will differ depending on the unit
that is connected.
• To enable the selection of External disc control mode 2/AUX
mode, you should connect optional switching adapter KCA-
S210A (which allows you to select both External disc control
mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-
CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) or
switching adapter CA-C1AX (which allows you to select AUX
mode only).
This function allows you to turn down the volume quickly.
Turning Attenuator On/Off:
Press the ATT button to switch the attenuator on and off.
When the attenuator is on, the ATT indicator blinks.
When the attenuator is off, the volume returns to the original
level.
NOTE
Turning the volume up, or turning it all the way down deactivates
the attenuator function.
During the AUX mode, "AUX" (or AUX-name display) will show
in the display. When the CA-C1AX is being used, the AUX Mode
will replace the External Disc Control Mode.
• If you have selected Standby mode, the timer function that
turns the power off automatically will be activated.
To find out how to set the time on the timer, and how to cancel
the timer function, refer to the section on the Power OFF Timer
function under Menu settings (page 35).
The Power OFF Timer function is enabled only after the security
code (page 28) is set up.
Loudness
This function amplifies low and high tones when the volume is
turned down.
The LOUD indicator lights up, when the loudness function is
on.
NOTE
Selecting AUX-name display
Turning Loudness On/Off:
Holding down the DISP button for two seconds or more during
the AUX mode, AUX-name display is blinked for AUX-name
selection mode.
Pressing 4 or ¢ button during this mode allows you to select
"AUX", "TV", "VCP", "GAME" or "PORTABLE" in the AUX mode.
The AUX-name selection mode can be exited by pressing the
DISP button or doing nothing for 10 seconds.
Hold down the LOUD button for one second or more to switch
the loudness on and off.
NOTE
The loudness function does not affect non-fading pre-out.
Volume
Increasing Volume:
Press the 5 button to turn up the volume.
Decreasing Volume:
Press the ∞ button to turn down the volume.
— 9 —
General features
Theft Deterrent Faceplate
The faceplate can be reversed to hide the control panel or
detached form the unit, helping to deter theft.
Egnlish
Removing the Faceplate:
1 • When the control panel is visible:
Press the release button.
2CAUTION
• When the control panel has been hidden:
Press the upper side of the faceplate.
Do not set the right side of the faceplate in the faceplate bracket
first, when reattaching the faceplate. Doing so may cause the
connector on the faceplate bracket to malfunction.
2 Holding the centre part of the faceplate, pull it out.
2 Press the right side of the faceplate until it locks.
Hiding the control panel:
1 Press the release button and slide open the faceplate.
2 Push upward the back of the control panel and reverse the
panel.
3 Push back the bottom of the faceplate bracket until it locks.
2CAUTION
• Do not apply excessive force to the faceplate bracket without
attaching the faceplate. Doing so will cause the faceplate
bracket to be deformed.
• Do not touch the connector on the faceplate bracket after
removing the faceplate. Touching the connector may cause
damage to the unit.
NOTE
The panel cannot be reversed when the faceplate is not attached.
NOTE
Opening the control panel:
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate
in its special storage case whilst detached.
• Do not expose the faceplate or its storage case to direct
sunlight or excessive heat or humidity. Also avoid places with
too much dust or the possibility of water splashing.
1 Press the upper side of the faceplate.
The faceplate will open.
2 Push the bottom of the control panel and close the faceplate.
Reattaching the Faceplate:
1 Hold the faceplate so that the control panel faces the front
toward you and set the left side of the faceplate in the
faceplate bracket.
— 10 —
NOTE
Whilst the control panel is sliding, only available buttons are 0,
ATT, ▲, ▼ and SRC.
Clock display
Changing the Clock Display:
Each time you press the CLK button, the display switches
between the clock and each mode display.
NOTE
The clock indicator lights whilst the clock is displayed.
TEL Mute
Shut down the audio system temporarily whenever an
incoming call is received.
NOTE
The function will not work if a cable is not connected to the car
phone.
When the telephone rings:
When a call is received, "CALL" is displayed and all the unit
functions are temporarily interrupted.
Restoring Original Unit Source During Phone Call:
Press the SRC button.
"CALL" disappears from the display, and the volume of the
original source is restored gradually.
Turning TEL Mute Function Off After Phone Call:
Hang the phone up.
"CALL" disappears from the display.
The original source (i.e., the one used before the phone call) is
returned to automatically, and the volume restored gradually.
— 11 —
General features
System Q
2 Press the Q button to enter the speaker setting mode.
You can recall the best audio setting preset for different types
3 Press either the 4 or ¢ button to select the type of
speaker. The setting switches as follows.
Off ("SP OFF") / For 6/6x9 in. speaker ("SP 6*9/6inch") /
For 5/4 in. speaker ("SP 5/4inch") /
of the music.
Egnlish
Switching the Preset Sound Setting:
Each time you press the Q button, the preset sound setting
switches as follows:
For the OEM speaker ("SP O.E.M.")
4 Press the Q button to end the speaker setting mode.
NOTE
Scan of Flat – Easy
(Default setting)
Easy
Jazz
Pops
Speaker setting function allows for tuning of bass, middle and
treble
User memory*
*User memory:
Flat
The unit returns to the state
adjusted the last time with
the audio control setting feature.
Top 40
Rock
As you proceed, each indicator would go on.
Function of the KDC-6090R
NOTE
Non-Fading Output
You can turn the non-fading output on and off whilst the
preout is switched to the non-fading preout.
The System Q function changes the values of the following
sound quality parameters:
Bass centre frequency, bass level, bass quality factor, bass
extend, middle centre frequency, middle level, middle quality
factor, treble centre frequency, treble level non-fading level, high-
pass filter frequency for front output, high-pass filter frequency
for rear output, and low-pass filter frequency for non-fading
output.
Turning non-fading output On/Off :
Hold down the NF button for one second or more to set the
function ON or OFF.
"NF ON" is displayed when the non-fading output is set ON.
Their setting values are different depending on the setting of the
speaker setting mode.
Speaker Setting
This function allows you to adjust the setting that is recalled
with the System Q, according to types of speakers.
1 Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
— 12 —
Audio control features
Audio Control Setting
Adjust various parameters of sound quality.
AUD
1 Hold down the AUD button for one second or more to enter
the control mode.
2 Selecting mode
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
Please refer to the following for the contents of the
adjustment modes.
FM
AM
4
¢
NOTE
Source tone memory
KDC-6090R/KDC-5090R
Each source (CD, FM, AM, and disc changer) has its own
memory in which to store the bass, middle, treble and N-F level
settings. (N-F level : KDC-6090R only)
The settings made for a particular source are then recalled
automatically whenever you use that source (e.g., FM mode
uses the tone settings made for FM, AM for AM, etc.).
Selecting mode
Setting value
3 Adjust each mode
Press the 4/¢ button.
Look at the table to adjust the mode being displayed.
4 Press the AUD button to end the control mode.
NOTE
Determining the parameters in the audio control setting will clear
all the adjustments made in the System Q and they are replaced
with the values made in the audio control setting.
KDC-V6090R
Selecting mode
Setting value
— 13 —
Audio control features
Function of the KDC-6090R
Bass Level
Adjust the bass level.
Non-Fading Level
Adjust the Non-fading output level.
Display and setting:
Egnlish
"Bass" : - 8 – + 8
Display and setting:
"NF Level" : - 15 – + 15
NOTE
This mode is available only when the non-fading output function is
set to on.
Middle Level
Adjust the middle level.
Display and setting:
"Middle"/"MID" : - 8 – + 8
Function of the KDC-6090R
High-pass Filter Frequency for Front Output
Adjust the frequency of the High-pass filter for front output.
Display and setting:
Treble Level
Adjust the treble level.
"HPF F" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /
150Hz / 180Hz / 220Hz
Display and setting:
NOTE
"Treble"/"TRE" : - 8 – + 8
You can separately set the high-pass filter for front and rear
output, including preouts. The high-pass filter works except
during non-fading preout when switched to non-fading.
Balance Level
Adjust the balance level.
Function of the KDC-6090R
High-pass Filter Frequency for Rear Output
Adjust the frequency of the High-pass filter for rear output.
Display and setting:
"Balance" : Left 15 – Right 15
Display and setting:
"HPF R" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /
150Hz / 180Hz / 220Hz
NOTE
Fader Level
Adjust the fader level.
You can separately set the high-pass filter for front and rear
output, including preouts. The high-pass filter works except
during non-fading preout when switched to non-fading.
Display and setting:
"Fader" : Rear 15 – Front 15
— 14 —
Tuner features
Function of the KDC-6090R
DISP
SRC
Low-pass Filter Frequency for Non-Fading Output
Adjust the frequency of the Low-pass filter for Non-Fading
output.
Display and setting:
"LPF NF" : 50 Hz / 80 Hz / 120 Hz / Through
NOTE
This mode is available only when the non-fading output function is
set to on.
#1-6
AM
FM
4
¢
KDC-6090R/KDC-5090R
Function of the KDC-6090R
Phase for Non-Fading Output
Band display
Frequency
Preset station number
Adjust the phase for Non-Fading output.
Display and setting:
"NF Phase" : Normal (0°) / Reverse (180°)
NOTE
This mode is available only when the non-fading output function is
set to on.
AUTO indicator
ST indicator
KDC-V6090R
Volume Offset
Set the sound level of the each source selected by adjusting
the level difference between the basic sound level and the
required level.
Band display
Frequency
Preset station number
Display and setting:
"V Offset"/"VOL Offset" : - 8 –
0
AUTO indicator
ST indicator
— 15 —
Tuner features
Tuning
1 Select the band/station that you want to have stored.
2 Hold down the button (#1-6) that you want to use for the
station, for two seconds or more.
1 Press the SRC button repeatedly until the tuner mode is
obtained. "TUNER" is displayed only when the tuner mode is
selected.
Egnlish
The button number blinks once in the display to indicate that
the data has been stored.
2 Press either the FM or AM button to select the band.
Each time you press the FM button, the band switches
between the FM1, FM2 and FM3.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Press the AM button to select the MW and LW bands.
NOTE
3 • Auto Seek Tuning
You can store 6 stations in each of the FM1, FM2, FM3, and AM
(MW and LW) bands.
Press the ¢ button to seek increasing frequencies.
Press the 4 button to seek decreasing frequencies.
• Preset station seek tuning
Press the ¢ button to move to the next preset station (i.e.,
the one with the next highest number), and the 4 button to
move to the last preset station (i.e., the one with the next
lowest number).
Switching Display for Tuner
NOTE
You can change the display used when listening to the radio.
If the frequencies stored at the preset numbers receive
stations which were not originally memorized when travelling
long distances, the preset number is not displayed. In such
cases, pressing the 4/¢ button to use preset station
seek will receive channel 1.
Switching the Display:
Each time you press the DISP button, the display changes as
follows:
• Manual Tuning
Programme Service name (only during RDS station reception)/
Station frequency
Press the ¢ button to increase the frequency by one step.
Press the 4 button to decrease the frequency by one step.
NOTE
Radio text (only during RDS station reception)
• The ST indicator lights up when stereo broadcasts are being
received.
Displaying Frequencies during programme service name
display:
• Please see the menu settings about selecting tuning mode.
(page 33)
Hold down the DISP button for one second or more.
The frequency for the RDS station will be displayed for five
seconds instead of the station name.
NOTE
If the RDS station currently tuned to is transmitting no text whilst
the Radio Text Display mode is turned on, "NO TEXT" will appear
in the display. Whilst awaiting reception, "Waiting" will be
displayed.
Station Preset Memory
Store the frequency of the station currently being listened to.
You can then recall that station with a single touch of a button.
— 16 —
RDS features
2WARNING
DISP
PTY
To prevent accidents, drivers should not look at the display whilst
driving.
#1-6
TI/
VOL ADJ
AM
FM
4
¢
KDC-6090R/KDC-5090R
PTY indicator
NEWS indicator
TI indicator
RDS indicator
KDC-V6090R
PTY indicator
NEWS indicator
TI indicator
RDS indicator
— 17 —
RDS features
RDS (Radio Data System)
Traffic Information Function
RDS is a digital information system that lets you receive
signals besides those of regular radio programmes, such as
network information being transmitted from radio stations.
When listening to an RDS station (ie, a station with RDS
capability), the programme service name of the station is
displayed along with the frequency, advising you quickly
which station is being received.
RDS (Radio Data System) stations also transmit frequency data
for the same station. When you are making long trips, this
function automatically switches to the particular frequency
with the best reception for the particular network of stations
that you want to listen to. The data is automatically stored,
allowing you to switch quickly to another RDS stations,
broadcasting the same programme, that has better reception.
These include stations stored in the station preset memory
that you often listen to.
You can listen to traffic information. If you are listening to
tapes or discs, they will continue playing until a traffic bulletin
is broadcast.
Egnlish
Turning TI function On/Off:
Press the TI button to turn the function on and off.
When the function is on, the TI indicator is turned on.
When none is being received, the TI indicator will blink on and
off. When a traffic information station is being received, the TI
indicator will turn on.
When a traffic bulletin begins to be broadcast, "Traffic Info" will
be displayed, and reception will begin at the preset volume.
If you are listening to a tape or disc when a traffic bulletin
begins, they will automatically be turned off. When the bulletin
ends or poor reception is experienced, the tape or disc will
begin playing again.
NOTE
Pressing the TI button whilst in the MW/LW band automatically
switches reception to the FM band. However, the MW/LW band
is not returned to when the TI button is pressed again.
Switching to a Different Traffic Information Station:
Use the 4 / ¢ buttons to make an auto seek of the TI
stations in a certain band.
Enhanced Other Network
Stations that offer <Enhanced Other Network> also transmit
information about other RDS stations that have traffic
information. When you are tuned to a station that is not
transmitting traffic information, but another RDS station starts
transmitting a traffic bulletin, the tuner automatically switches
to the other station for the duration of the bulletin.
NOTE
• When you are listening to a tape or disc, you cannot change to
another TI station.
• When the auto TP seek function is turned on and reception
starts to weaken, the tuner automatically seeks traffic
information stations with better reception.
• If you are tuned to a station that is not a traffic information
station itself but which provides <Enhanced Other Network>
services, you can still have traffic information received.
• Holding down the TI button for one second or more when the
TI function is on in the tape or disc mode results in a change to
the frequency display of the traffic information station for five
seconds.
Alarm
When an emergency transmission (announcing disasters, etc.)
is sent, all current functions are interrupted to allow the
warning to be received.
— 18 —
NOTE
Presetting Volume for Traffic Information/News
Please see the menu settings (page 34) about switching between
manual scrolling and automatic scrolling.
Preset the volume level to be used for traffic information and
news broadcasts.
1 Tune into the station for which you want to set the volume.
2 Adjust the volume to the desired level.
3 Hold down the VOL ADJ button for two seconds or more.
The volume level blinks once in the display to indicate that the
data has been stored.
Future traffic information/news broadcasts are heard at the
preset level.
NOTE
• The volume cannot be lowered by this function during tuner
reception. The volume is only set when it is louder than the
listening volume of the tuner.
• You can arrange only to listen to traffic information or news
bulletins with at preset volume with the volume set at
minimum.
Radio Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
To scroll manually:
1 Press the DISP button to display the Radio Text.
2 Holding down the DISP button for one second or more results
in one scrolling display of the text.
To scroll automatically:
1 Press the DISP button to display the Radio Text.
The text will be displayed in one scrolling display.
2 Holding down the DISP button for one second or more results
in one scrolling display of the text.
— 19 —
RDS features
24. Jazz Music
(Jazz)
Programme Type (PTY) Function
Conduct auto seek tuning only on those stations with selected
kinds of programmes.
25. Country Music
26. National Music
27. Oldies Music
28. Folk Music
(Country)
(Nation M)
(Oldies)
Egnlish
(Folk M)
(Document)
1 Press the PTY button.
29. Documentary
"PTY" is displayed, and the Programme Type Selection (PTY)
Mode entered.
(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)
• You can select the type of programme directly by pressing a
preset button. The buttons are factory-set to the following
type of programmes:
If you make no key input in 30 seconds, the mode will
automatically turn off.
NOTE
1. Music
4. Other Music
2. Speech
5. Serious Classical
3. News
6. Varied
You cannot use this function whilst the traffic bulletin is received.
NOTE
Changing the Preset Button Settings for Programme Type
2 Select the type of programme to be received
• Press either the FM or AM button repeatedly until the type of
programme you want to listen to.
After selecting the type of programme to be stored in a certain
preset button, hold down that button for two seconds or more.
The previously stored data for that button are erased and the
new programme type is stored.
The selection includes:
Speech
(Speech)
(Music)
Music
1. News
3 Seeking the selected programme type
(News)
Press the 4 or ¢ button to make a seek of frequencies
2. Current Affairs
3. Information
4. Sports
(Affairs)
(Info)
(Sport)
(Educate)
(Drama)
(Culture)
(Science)
(Varied)
with your selected type of programme.
The display blinks and the seek starts.
If your selected type of programme is found, the name of the
station is displayed and the station is tuned into.
"PTY Found" is displayed for about 30 seconds.
If you make no key input in 30 seconds, the PTY selection
mode will turn off automatically.
5. Education
6. Drama
7. Culture
8. Science
9. Varied
NOTE
10. Pop Music
11. Rock Music
12. Easy Listening Music
13. Light Classical
14. Serious Classical
15. Other Music
16. Weather
(Pop M)
(Rock M)
(Easy M)
(Light M)
(Classics)
(Other M)
(Weather)
(Finance)
If no programme can be found, "NO PTY" is displayed.
If you want to select another type of programme, repeat steps 2
and 3 above.
Switching to Other Stations with the Same Type of
Programme:
When "PTY Found" is displayed, perform auto seek tuning.
The tuner scans for another station with the same type of
programme.
17. Finance
18. Children’s programmes (Children)
19. Social Affairs
20. Religion
21. Phone In
22. Travel
(Social)
Cancelling Programme Type Function During Its Operation:
(Religion)
(Phone In)
(Travel)
Press the PTY button.
23. Leisure
(Leisure)
— 20 —
CD/External disc control features
Changing Language for Programme Type(PTY)
Function
FM
0
38
SRC
Changing the display language to another language.
1 Press the PTY button.
"PTY" is displayed, and the Programme Type Selection (PTY)
Mode entered.
2 Enter the Changing Language Mode
Press the DISP button to enter the changing language mode.
SCAN
RDM
REP
DISP/
NAME.S
AM
3 Changing the Display Language
Press the FM or AM button.
Release
button
4
¢
M.RDM
Each time the button is pressed, the display language will
change as follows:
KDC-6090R/KDC-5090R
Track time
Disc number
Track number
English
Spanish
French
Dutch
German
Swedish
Portuguese
Norwegian
IN indicator
4 Press the DISP button to end the changing language mode.
KDC-V6090R
Track number
Track time
Disc number
IN indicator
— 21 —
CD/External disc control features
NOTE
Playing CDs
• When you load a CD and eject it right away, the next time you
try to insert the CD may not load. In such a situation, take the
CD out for a moment and then reinsert it.
Playing CDs:
Press the release button to slide open the faceplate, showing
the CD insertion slot.
Egnlish
• Whilst the control panel is sliding, only available buttons are 0,
Holding the CD with the labeled side facing up, insert it in the
slot. The CD will start playing. Push back the bottom of the
faceplate with your hand until it locks.
ATT, ▲, ▼ and SRC.
The IN indicator will light when a CD has been inserted.
2CAUTION
When inserting a CD, make sure the CD has been completely
drawn in before pushing back the faceplate. Failing to do so
might scratch the CD.
Playing Other Disc mode
This function permits the connection of optional players and
the playing of discs other than the loaded CD (in the current
unit).
Playing CDs Already Inserted:
Press the SRC button repeatedly until the CD mode is
obtained.
Playing Discs:
"CD" is displayed when the CD mode has been selected.
The CD will start playing.
Press the SRC button repeatedly to select the external disc
control mode.
Pausing and Restarting CD Play:
The disc will start playing.
NOTE
Press the 38 button to make the disc pause.
Press the same button again to start play again.
The external disc control mode will differ, depending on the unit
that is connected.
Mode Display Examples
• "CD2"...when a CD player is connected
• "DISC"...when a disc changer is connected
• "DISC-1", "DISC-2"...when two disc changers are connected
Eject:
Press the release button and slide open the faceplate.
Press the 0 button.
The CD stops playing and ejects from the slot.
Push back the bottom of the faceplate with your hand until it
locks.
Pausing and Restarting Disc Play:
2CAUTION
Press the 38 button to make the disc pause.
• Do not attempt to insert a CD into the slot if another one is
already there.
• The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm
(3-inch) CD, it will get stuck inside and can cause the unit to
malfunction.
• When the faceplate has been slid open, it might interfere with
the gear lever or something else. If this happens, pay attention
to safety and move the gear lever or take an appropriate action,
then operate the unit.
• Do not use the unit with the faceplate in the open condition.
Doing so will cause breakdown.
Press the same button again to start play again.
NOTE
• When one disc has finished playing its last track, the next disc
in the changer starts playing. When the last disc in the changer
has finished, the player returns to the first disc and starts
playing it.
• Disc #10 is displayed as "0".
— 22 —
You cannot make a forward track search when listening to the
last track on a disc.
Fast Forwarding and Reversing Disc Play
Fast Forwarding Disc Play:
Hold down on the ¢ button.
Release your finger to play the disc at that point.
Reversing Disc Play:
Hold down on the 4 button.
Disc Search
Search forwards or backwards through the discs in a disc
changer until you reach the one that you want to listen to.
(Function of disc changers)
Release your finger to play the disc at the point.
NOTE
You cannot use reverse play between tracks depending on the
model being connected. Instead, the reverse play function is
cancelled when it reaches the beginning of a track, at which
point normal play automatically resumes.
Making a Reverse Disc Search:
Press the AM button to display the desired disc number.
Each time the button is pressed, the displayed disc number
decreases by one.
Play starts at the beginning of the displayed disc.
Making a Forward Disc Search:
Press the FM button to display the desired disc number.
Each time the button is pressed, the displayed disc number
increases by one.
Track Search
Search forwards or backwards through the tracks on the disc
until you reach the one that you want to listen to.
Play starts at the beginning of the displayed disc.
NOTE
"Load" is displayed when discs are being exchanged on the disc
changer.
Making a Reverse Track Search:
Press the 4 button to display the desired track number.
Press once to search back to the beginning of the current
track, twice to search back to the beginning of the previous
track, and so forth.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
Pressing the 4 button whilst listening to track 1 only searches
back to the beginning of that track. The reverse search is not
"recycled" to the last track on the disc.
Making a Forward Track Search:
Press the ¢ button to display the desired track number.
Press once to fast forward to the next track, twice to fast
forward to the track after that, and so forth.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
— 23 —
CD/External disc control features
Track / Disc Repeat
Random Play
Repeat playing the current track or disc.
Play all the tracks on the current disc in random order.
Turning Repeat Play Function On/Off:
Press the REP button to switch the repeat play function on and
off as follows :
1 Press the RDM button to switch the random play function on
and off.
Egnlish
"Random ON" is displayed when random play is turned on.
The display of the track number changes continuously as the
next track is being selected.
▼
Track Repeat ON
▼
When the track has been selected, play starts.
The selected track number blinks in the display as it is being
played.
Disc Repeat ON (Function of disc changers)
▼
Repeat OFF
NOTE
(For disc changers)
When all the tracks on a certain disc have been played using the
random play function, the next disc on the changer starts playing
(with the random play function still turned on).
"Repeat ON"/"T-Repeat ON" is displayed and the track number
blinks in the display when track repeat is on.
"Disc Repeat ON"/"D-Repeat ON" is displayed and the disc
number blinks in the display when disc repeat is on.
2 To change the track being heard, press the ¢ button.
Another track is selected and played.
NOTE
NOTE
Repeat play is cancelled when you eject the disc.
Random play is cancelled when you eject the disc.
Track Scan
Successively play the beginning of each track on a disc until
Magazine Random Play
Play the tracks on all the discs in the disc changer in random
order.
(Function of disc changers)
you find the track that you want to listen to.
Starting the Track Scan:
Press the SCAN button. "Scan ON" is displayed and the first 10
seconds of each track are played, and the tracks are played in
order.
1 Press the M.RDM button to switch the magazine random play
function on and off.
The track number currently being heard blinks in the display.
"M.Random ON" is displayed when magazine random play is
turned on.
Stopping to Listen to the Track Being Scanned:
Press the 38 or SCAN button again to stop the scan and keep
on listening to a track normally.
The display of the disc and track numbers change continuously
as the next track is being selected.
When the disc/track has been selected, play starts.
The selected disc/track number blinks in the display as it is
being played.
NOTE
• The track scan function is cancelled when you eject the disc.
• The track scan function only scans each track on a disc once.
— 24 —
2 To change the track being heard, press the ¢ button.
Another disc/track is selected and played.
NOTE
• Magazine random play is cancelled when you eject the disc.
• The time needed for random selection depends on the number
of discs loaded in the disc magazine.
Switching Display for Discs
Switch the display that appears whilst discs are playing.
Switching Display for Discs:
Each time you press the DISP button, the display during disc
play switches as follows:
Track time
Disc name (DNPS) (only when being preset)
Disc title (Units featuring CD text/MD only)
Track title (Units featuring CD text/MD only)
NOTE
• You can give names to discs through the presetting disc name
function (page 26).
Note that depending on the unit, display may not be possible.
• If you try to display the name of a disc that does not have one,
"NO NAME" is displayed instead.
• When there is an attempt to display the title of a disc for which
the disc title/track title has not been recorded, "NO TEXT" is
displayed for CD and "NO TITLE/NO NAME" is displayed for
MD.
• If you attempt to display disc title/track title when connecting
the CD changer not supported for CD text feature, caution
messages such as "NO TEXT" or "Reading" may be displayed.
• Depending on the type of characters of the CD Text, some
characters may not be displayable.
— 25 —
CD/External disc control features
is displayed.
Text / Title Scroll
2 Hold down the NAME.S button for two seconds or more.
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
"NAME SET" is displayed and the disc name preset mode is
entered.
Egnlish
The cursor blinks in the position where character input can be
made.
To scroll manually:
1 Press the DISP button to display the disc title or the track title.
3 Press either the 4 or ¢ button to move the cursor to the
desired position.
2 Holding down the DISP button for one second or more results
The 4 button moves the cursor to the left, and the ¢
in one scrolling display of the titles.
button to the right.
To scroll automatically:
4 Each time the 38 button is pressed, the characters to be
entered change as listed below.
1 Press the DISP button to display the disc title or the track title.
The titles will be displayed in one scrolling display.
Press the FM or AM button to display the desired character.
Characters that can be displayed are as follows.
NOTE
When the disc or track to be played changes, the title is
displayed in one scrolling display.
Alphabet (upper case): A ~ Z
2 Holding down the DISP button for one second or more results
Alphabet (lower case): a ~ z
in one scrolling display of the titles.
NOTE
Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]
• Please see the menu settings (page 34) about switching
between manual scrolling and automatic scrolling.
• Only units with a CD text feature permit title display.
• You cannot use the text scroll function during magazine random
play.
Special characters: á à
é
è
í
ì
ó
ò
ú
ù
Ñ
Ç
ë
î ï
ô
ö
û
ü
ñ
ç
©
Æ
›
5 Continue steps 3 and 4 until all the characters are chosen for
the name.
NOTE
You can enter up to 12 characters for each name.
6 Press the NAME.S button.
The disc name is stored and the disc name preset mode is
cancelled.
Presetting Disc Names (DNPS)
Store the names of discs to be displayed when played.
If you make no entry in a 10-second period, the name will be
stored with the characters input so far.
NOTE
1 Play the disc whose name you want to preset.
NOTE
• The number of discs whose names can be stored will differ
depending on the disc changer that is connected. Please see
your disc changer manual for details.
• This function is not available for disc changers that do not
feature the Disc Name Preset function.
• The Disc Name Preset function cannot be used during the
Magazine random play as well as whilst a disc title or track title
Up to 30 CDs can be registered with this unit.
— 26 —
Menu settings
• Discs are identified by their total length and number of tracks. If
another disc happens to have the same specifications as one
that you have already stored a name for, the name will be
displayed for it, too.
SRC
MENU
• If you want to change the name of a disc, repeat steps 1 and 2
to display the name, and then repeat steps 3 and 4 to input the
changes.
• Pressing the reset button erases the disc names stored in this
unit, but does not erase the names stored in a disc changer.
#1-6
FM
AM
4
¢
DISP
KDC-6090R/KDC-5090R
Menu display
RDS indicator
AUTO indicator
NEWS indicator
KDC-V6090R
Menu display
RDS indicator
AUTO indicator
NEWS indicator
— 27 —
Menu settings
Menu System
Code Security Function
You can set the defaults for additional functions in the menu
mode. Make a setting for each function, referring to the
following operations.
After a security code has been registered, power cannot be
restored if the battery is disconnected from the unit unless the
code is first input.
Egnlish
NOTE
1 Enter the menu mode
Hold down the MENU button for one second or more.
"MENU" is displayed when the menu mode is entered.
The function that you can adjust is indicated with the current
settings displayed.
All the steps in this procedure (1 through 7) must be completed
before the code security function can be turned on. However,
once the procedure is finished, it need not be repeated.
Once the code security function has been activated, "Security"
disappears from the MENU system. Note that it will no longer be
possible to cancell this function afterwards.
2 Selecting function to set
Press the FM button to search through the functions until you
see the one you want to adjust in the display.
Press the AM button to search through the functions
backward.
1 Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
2 Hold down the MENU button for one second or more.
Function items change in the order of features that follow in
the menu system.
"MENU" is displayed first and then "Security" is displayed.
Example: If you want to switch the setting of the touch sensor
tone function from on to off, first search through the
functions until you see "Beep ON" in the display.
3 Hold down either the 4 or ¢ button for one second or
more.
"ENTER" will appear in the display for one second, indicating
the code setting mode has been entered. When "CODE"
appears in the display, you can start inputting the code.
3 Changing setting for currently displayed function
Press either the 4 or ¢ button.
The setting will change for each function.
4 Press the preset button and enter your security code.
Use the security code shown on your Car Audio Passport.
Example: Enter "3510" as your code, pressing the buttons as
follows:
Example: The setting of the touch sensor tone will switch from
on to off, and "Beep OFF" is displayed.
4 Ending the menu mode
Press the MENU button.
# Times
pressed
Step
Button to press
Display
NOTE
1
2
3
4
#1
#2
#3
#4
4
Make sure to end the menu mode when finished.
If you fail to end the menu mode, several functions may not
operate properly, including the Traffic Information function, the
News Bulletin function with PTY news timeout setting, and the
Alarm function.
“3”
“5”
“1”
“0”
6
2
1
5 Hold down the DISP button for three seconds or more.
The security code will be set.
"RE-ENTER" will appear in the display for one second, asking
you to enter the code once again for confirmation. When
— 28 —
"CODE" appears in the display, you can start inputting the code.
Touch Sensor Tone
This function produces a beep sound that accompanies button
operation. It can be switched on or off.
6 Press the Preset button and input the security code again.
7 Hold down the DISP button again for three seconds or more.
"APPROVED" will appear in the display, with the code security
function turning on. From this point on, if the unit is
disconnected from the battery, the security code must be
entered the first time that the unit's power is turned on.
"ENTER" and "CODE" will appear in the display, asking you to
input the code.
Display and setting:
"Beep ON" : Beep setting is on. (Default setting)
"Beep OFF" : Beep setting is off.
NOTE
The beep sound is not output from the preout jacks.
NOTE
If you input an incorrect security code, the code setting mode
will be cancelled automatically. Follow the steps from 3 to 7
above again.
If you press the RESET button or remove the battery:
The first time you turn the unit on again, "CODE" will appear in
the display, asking you to input the security code.
Repeat steps 6 and 7 above, and input the security code.
You can start operating the unit again when "APPROVED"
appears in the display.
NOTE
If you enter the wrong code, "Waiting" is displayed and you
cannot make further input of the code for a fixed interval (see
table below), which grows longer each time you enter the wrong
code.
When "CODE" is displayed, you can make input again.
Number of wrong
inputs
Interval until next input
is allowed
1
2
3
4
-
5 minutes
1 hour
24 hours
The number of wrong inputs is displayed.
— 29 —
Menu settings
Tune into an RDS station for 3 or 4 minutes.
Manual Time Adjustment
Adjust the time manually.
The time adjusts automatically to the correct local time.
NOTE
NOTE
The time is not adjusted when the RDS station you are tuned to
is not transmitting a time signal. Choose another RDS station in
such a case.
Egnlish
This adjustment is available only when the automatic time
adjustment is set to off. (page 30)
Display and setting:
1 Select the display "Clock Adjust" during the selecting function
in the menu system.
2 Hold down either the 4 or ¢ button for one second or
more to enter the Manual time adjustment mode.
The time display will blink.
Selectable Illumination
You can switch the colour of the button illumination between
green and red.
3 • Adjusting the hours
Press the FM button to advance the hours, or press the AM
button to make the hours go back.
Display and setting:
"Button Green" : The colour of the illumination is green.
"Button Red" : The colour of the illumination is red.
• Adjusting the minutes
Press the ¢ button to advance the minutes, or press the
4 button to make the minutes go back.
4 Press the MENU button to end the Manual Time Adjustment
mode.
Exiting the Manual Time Adjustment mode would start the
clock counting.
Switching Graphic Display
This function allows you to turn off the lower part of the
display if there is too much information in the display.
Display and setting:
"Graphic ON" : The display will turn on by using the whole part
of the display. (Default setting)
"Graphic OFF" : The display will turn on by using only the upper
part of the display and the IN indicator.
Automatic Time Adjustment
With automatic time adjustment, you can set the clock time
automatically according to time data sent from RDS stations
(after receiving RDS signals for several minutes). You can also
set the time manually if the automatic time adjustment
function is turned off.
Display and setting:
"SYNC ON" : Automatic time adjustment (Default setting)
"SYNC OFF" : Manual time adjustment
Adjusting Time Automatically:
— 30 —
The 4 and ¢ buttons are used to adjust the blue color
tones, respectively.
Function of the KDC-V6090R
Variable Illumination Colour Setting
You can set the display to a desired colour.
Press the #3 button to end the blue adjust mode.
6 To store the colour setting in the memory:
(colour preset memory)
Display and setting:
After adjusting the illumination colours, press the #5 button for
two seconds to store the colour setting in the memory.
Pressing the #5 button again recalls the stored colours from
the memory.
1 Select the display "Color" during the selecting function in the
menu mode.
2 To set a colour manually:
Hold down on the 4 or ¢ button.
NOTE
Pressing the ¢ button advances the colour, and pressing the
4 button reverses it.
The Blue Adjust mode setting cannot be stored in memory.
When the desirable colour appears, release the button.
7 Press the MENU button to end the Variable Illumination Colour
Setting mode.
3 To make the popular colours appear:
Press the preset button(#1-4) for the desired color.
The buttons #1-4 are preset for the following four colours:
#1: White
#2: Red
#3: Blue
Contrast Adjustment
#4: Blue Green
This adjustment permits easy viewing of the display.
4 To switch colours depending on the situation:
(Situational Mode)
Display and setting:
Each time you press the #6 button, the mode switches as
follows:
"Contrast 0" – "Contrast 10"
NOTE
▼
The initial setting value is "5".
Scan Mode
▼
SRC Mode
(Changing colours depending on the source being played)
▼
Time Mode
Dimmer
You can dim the display.
(Colour changes every six hours)
▼
Situational Mode off
NOTE
The dimmer function is not available for units if the dimmer cable
is not connected.
When the Situational Mode is off, the original colour setting
resumes.
Display and setting:
5 To finely adjust blue: (Blue Adjust Mode)
Press the #3 button for two seconds or more to enter the
blue adjust mode.
"Dimmer ON" : The dimmer setting is on. (Default setting)
"Dimmer OFF" : The dimmer setting is off.
— 31 —
Menu settings
As of December 2000, the power amplifiers controllable by the
main unit are as follows:
KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T
Function of the KDC-6090R
Switching preout
Switch the preout between the rear and non-fading. When you
switch to non-fading, you can adjust the volume separately.
Egnlish
Display and setting:
"SWPRE Rear" : Rear preout (Default setting)
"SWPRE N-Fad" : Non-fading preout
NOTE
News Bulletin Function with PTY News Timeout
Setting
You can arrange to have news bulletins interrupt your current
listening source, including other radio stations. When the
News Bulletin function is on, the PTY News Timeout setting
allows you to set the interval during which further news
interruption cannot take place. You can adjust the PTY news
interruption period from 10 to 90 minutes for each journey.
You cannot use the high-pass filter with non-fading preout.
System Q
Display and setting:
When this system is set to on, the System Q factors (Bass
centre frequency, Bass quality factor, Bass extend, Middle
centre frequency, Middle quality factor, and Treble centre
frequency) appear during the audio control mode.
"News OFF" (Default setting), "News 00min" – "News 90min"
(min= minutes)
: When you select the news interruption timeout interval, the
News function turns on and the NEWS indicator lights up.
When a news bulletin is received, "News" will be displayed
and reception will begin at the preset volume.
Display and setting:
"System Q ON" : The System Q factors appear and can be
adjusted. (Default setting)
NOTE
"System Q OFF" : The System Q factors do not appear.
• If you choose the "20min" setting, further news bulletins will not
be received for 20 minutes once the first news bulletin is
received.
• This function is only available if the desired station sends PTY-
code for news bulletin or belongs to <Enhanced Other
Network>-Network sending PTY-code for news bulletin.
• If you turn on the news bulletin function in the MW/LW band,
the band is switched automatically to the FM band.
However, the MW/LW band is not returned to when you turn
off the function.
External Amp Control
Adjust the bass boost level of the external amplifier using the
main unit.
Display and setting:
"AMP Bass FLT" : Bass boost level is flat. (Default setting)
"AMP Bass +6" : Bass boost level is low (+6dB).
"AMP Bass +12" : Bass boost level is high (+12dB).
NOTE
— 32 —
When all the stations in a certain band are stored in the preset
memory, the auto memory entry stops. The tuner then plays
the last station received.
Local Seek Function <In Tuner mode>
With the local seek function turned on, auto seek tuning skips
stations with relatively poor reception.
NOTE
Display and setting:
• When the AF function is turned on whilst auto memory entry
takes place, only RDS stations (i.e., stations with RDS
capability) are stored. RDS stations that have been preset for
FM1 cannot also be preset in FM2 or FM3.
"Local.S ON" : The local seek function is on.
"Local.S OFF" : The local seek function is off. (Default setting)
• When the local seek function is turned whilst auto memory
entry takes place, stations with poor reception are not stored.
• When the Traffic Information function is on, only the local traffic
information station frequency will be stored.
Selecting Tuning Mode <In Tuner mode>
Cancelling Auto Memory Entry During Its Operation:
Press the 4 / ¢ button whilst auto memory entry is taking
place to stop the process.
You can choose from three tuning modes: auto seek, preset
station seek, and manual. The "AUTO 1" indicator lights up
when auto seek tuning is selected, and the "AUTO 2" indicator
lights when preset station seek tuning is selected.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Display and setting:
"Auto 1" : Auto seek tuning mode (Default setting)
"Auto 2" : Preset station seek tuning mode
"Manual" : Manual tuning mode
Auto Memory Entry <In Tuner mode>
You can automatically store all the receivable frequencies in
the band currently being listened to, and then recall them with
the touch of a button later. This function is especially useful
when you are travelling and do not know what stations are
available. Up to 6 frequencies can be stored this way.
Display and setting:
1 Select the display "Auto-Memory" during the selecting function
in the menu system.
2 Hold down either the 4 or ¢ button for two seconds or
more to start auto memory function.
The numbers of the preset station buttons showed in order.
— 33 —
Menu settings
AF (Alternative Frequency) Function
Auto TP Seek Function
When poor reception is experienced, automatically switch to
another frequency broadcasting the same programme in the
same RDS network with better reception.
When the TI function is on and poor reception conditions are
experienced when listening to a traffic information station,
another traffic information station with better reception will be
searched for automatically. This function is on, when unit is
first powered on.
Egnlish
The RDS indicator lights up when the AF function is turned on.
Display and setting:
"AF ON" : The AF function is on. (Default setting)
"AF OFF" : The AF function is off.
Display and setting:
"ATPS ON" : The Auto TP Seek Function is on.
If the traffic information station you are tuned to
experiences poor reception, this function
automatically seeks another TP station. (Default
setting)
NOTE
When no other stations with stronger reception are available for
the same programme in the RDS network, you may hear the
incoming broadcast in bits and snatches. Turn off the AF function
in such a case.
"ATPS OFF" : The Auto TP Seek Function is off.
Monaural Reception
Restricting RDS Region (Region Restrict Function)
<In FM reception of Tuner mode>
You can choose whether or not to restrict the RDS channels,
received with the AF function for a particular network, to a
specific region. When the Region Restrict Function is on, the
region is restricted.
When poor stereo reception is experienced, this function will
reduce noise and improve listening conditions.
Display and setting:
"MONO ON" : The monaural reception is on.
"MONO OFF" : The monaural reception is off. (Default setting)
Display and setting:
"Regional ON" : The Region Restrict Function is on. (Default
setting)
"Regional OFF" : The Region Restrict Function is off.
NOTE
Sometimes stations in the same network broadcast different
programmes or use different programme service names.
Text Scroll <In FM or External disc control mode>
This function permits the CD text, MD title, and Radio tex to be
scrolled and the entire text to be displayed. Switching between
manual scrolling and automatic scrolling is permitted.
Display and setting:
"Scroll Auto" : Automatic scrolling
"Scroll MANU"/"Scroll Manual" : Manual scrolling (Default
setting)
— 34 —
Power OFF Timer
Set the time for the OFF Timer function activated when you
selected Standby mode.
If the predefined time elapses, this unit's power is
automatically turned off.
Display and setting:
"OFF – – – –" : Power OFF Timer function is cancelled.
"OFF 20min" : Unit's power goes OFF after 20 minutes.
(Default setting)
"OFF 40min" : Unit's power goes OFF after 40 minutes.
"OFF 60min" : Unit's power goes OFF after 60 minutes.
NOTE
The Power OFF Timer function is enabled only after the security
code (page 28) is set up.
— 35 —
Accessories
2CAUTION
• If your car is not prepared for this special connection-system,
consult your Kenwood dealer.
External view
Number of items
• Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
1
..........................................1
• Make sure that all cable connections are securely made by
inserting jacks until they lock completely.
Egnlish
• If your vehicle's ignition does not have an ACC position, or if
the ignition cable is connected to a power source with constant
voltage such as a battery cable, the power will not be linked
with the ignition (i.e., it will not turn on and off along with the
ignition). If you want to link the unit's power with the ignition,
connect the ignition cable to a power source that can be turned
on and off with the ignition key.
• If the fuse blows, first make sure that the cables have not
caused a short circuit, then replace the old fuse with one with
the same rating.
• Do not let unconnected cables or terminals touch metal on the
car or anything else conducting electricity. To prevent short
circuits, also do not remove the caps on the ends of the
unconnected cables or the terminals.
• Connect the speaker cables correctly to the terminals to which
they correspond. The unit may receive damage or fail to work if
you share the - cables and/or ground them to any metal part
in the car.
..........................................2
..........................................1
2
3
4
..........................................1
2CAUTION
The use of any accessories except for those provided might
result in damage to the unit. Make sure only to use the
accessories shipped with the unit, as shown above.
• After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
• Insulate unconnected cables with vinyl tape or other similar
material.
• Some disc changers need conversion cables for connection.
See the section on "Safety Precautions" for details.
• If the console has a lid, make sure to install the unit so that the
faceplate does not hit the lid when closing and opening.
Installation Procedure
1. To prevent short circuits, remove the key from the ignition and
disconnect the -terminal of the battery.
2. Make the proper input and output cable connections for each
unit.
3. Connect the cable on the wiring harness.
• Mount the unit so that the mounting angle is 30° or less.
4. Take Connector B on the wiring harness and connect it to the
speaker connector in your vehicle.
5. Take Connector A on the wiring harness and connect it to the
external power connector on your vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
— 36 —
Connecting Cables to Terminals
Antenna Conversion Adaptor (ISO–JASO) (Accessory3)
Antenna Cord (ISO)
Connector Function Guide
FM/AM
antenna input
Rear right output (Red) / Non-fading right
output (Red) (KDC-6090R only)
Rear left output (White) / Non-fading left
output (White) (KDC-6090R only)
Pin Numbers for
ISO Connectors
Cable Colour
Functions
External Power
Connector
Front right output (Red)
Front left output (White)
A–4
A–5
A–6
A–7
A–8
Yellow
Blue/White
Orange/White Dimmer
Red
Battery
Power Control
To KENWOOD disc changer/
Ignition (ACC)
Earth (Ground)
Connection
DAB control input/
KPA-SD100/KPA-HD100/KPA-
SS100
Black
Speaker
NOTE
Fuse(10A)
Connector
To connect these leads, refer to the
relevant instruction manuals.
B–1
B–2
B–3
B–4
B–5
B–6
B–7
B–8
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Wiring harness
(Accessory1)
External amplifier
control cable
(Pink / Black)
Green/Black
To "EXT.AMP.CONT." terminal of the
amplifier having the external amp
control function.
EXT.CONT.
TEL MUTE
Battery cable (Yellow)
TEL mute cable (Brown)
Ignition cable (Red)
Connect to the terminal that is
grounded when either the telephone
rings or during conversation.
NOTE
To connect the KENWOOD navigation
system, consult your navigation manual.
Connect either to the power control
terminal when using the optional
power amplifier, or to the antenna
control terminal in the vehicle.
A–7 Pin (Red)
Power control/ Motor antenna
control cable (Blue/White)
P.CONT.OUT
ANT.CONT.
A–4 Pin (Yellow)
Connector A
8
7
6
5
4
3
2
1
NOTE
If no connections are
made, do not let the cable
come out from the tab.
8
7
6
5
4
3
2
1
Connector B
— 37 —
Connecting Cables to Terminals
Installation
■
Installation
2WARNING
Connecting the ISO Connector (see p.37)
The pin arrangement for the ISO connectors depends on the
type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
The default connection for the wiring harness is described in 1
below. If the ISO connector pins are set as described in 2 or 3,
make the connection as illustrated.
Firewall or metal support
Screw (M4X8)
(commercially
available)
Egnlish
1 (Default setting) The A-7 pin (red) of the vehicle's ISO
connector is linked with the ignition, and the A-4 pin (yellow)
is connected to the constant power supply.
Unit
Vehicle
A–7 Pin (Red)
Bend the tabs of the
mounting sleeve
with a screwdriver or
similar utensil and
attach it in place.
Ignition cable (Red)
Self-tapping
screw
(commercially
available)
Battery cable (Yellow)
A–4 Pin (Yellow)
Metal mounting
strap
(commercially
available)
2 The A-7 pin (red) of the vehicle's ISO connector is connected
to the constant power supply, and the A-4 pin (yellow) is
linked to the ignition.
NOTE
Unit
Vehicle
Make sure that the unit is installed securely in place. If the unit
is unstable, it may malfunction (eg, the sound may skip).
Ignition cable (Red)
A–7 Pin (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
3 The A-7 pin (red) of the vehicle's ISO connector is not
connected to anything, whilst the A-4 pin (yellow) is
connected to the constant power supply (or both the A-7 (red)
and A-4 (yellow) pins are connected to the constant power
supply).
Unit
Vehicle
Connect to a power source that can be
turned on and off with the ignition key.
Ignition cable (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
— 38 —
■
■
Removing the hard rubber frame
Removing the Unit
1
Refer to the section “Removing the hard rubber frame (P. 39)”
and then remove the hard rubber frame.
1
Refer to the section “Theft deterrent faceplate (P. 10)” and
then remove the faceplate.
2
3
Remove the Hex-head screw with integral washer (M4´8) on
2
Engage the catch pins on the removal tool and remove the
two locks on the upper level.
Push upward the frame and pull it forward as shown in the
figure.
the back panel.
Insert the two removal tools deeply into the slots on each
side, as shown.
Screw (M4X8)
(commercially
available)
Catch facing up
Catch
Lock
Accessory2
Removal tool
Accessory2
Removal tool
4
Push upward the removal
tool toward the top, and
pull out the unit halfway
whilst pressing towards the
inside.
3
When the upper level is removed, remove the lower two
locations.
2CAUTION
Be careful to avoid injury from the catch pins on the removal
tool.
5
Pull the unit all the way out
with your hands, being
careful not to drop it.
NOTE
The frame can be removed from the bottom side in the same
manner.
— 39 —
Installation
■
Locking the faceplate to the unit
If you want to lock the faceplate to the unit so that it does not
fall off, follow the directions below.
1
2
Refer to the function "Theft deterrent faceplate" (page 10) and
remove the faceplate.
Egnlish
Insert the provided screw into the hole at the centre of the
bottom side of the faceplate which you have removed from
the unit.
Accessory4
3
4
Push back the bottom of the faceplate bracket unit it locks.
Refer to the section "Theft deterrent faceplate (page 10)" and
then reattaching the faceplate.
2CAUTION
Never insert the taptite screws (ø2 ´ 4 mm) in any other screw
holes than the one specified. If you insert it in another hole, it
will contract and may cause damage to the mechanical parts
inside the unit.
— 40 —
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not turn on.
The fuse has blown.
After checking for short circuits in the cables, replace
the fuse with one having the same rating.
No ACC position on vehicle ignition.
Connect the same cable to the ignition as the battery cable.
If you have selected Standby
mode, the power will go OFF
automatically.
The Power Off Timer function has been activated.
If you do not want the power to go OFF automatically,
cancel the Power Off Timer function.
No sound can be heard, or the
volume is low.
The Attenuator function is turned on.
Turn off the Attenuator function.
The fader and/or balance settings are set all the way to
one side.
Reset the fader and/or balance settings.
The input/output cables or wiring harness are connected
incorrectly.
Reconnect the input/output cables and/or the wiring
harness correctly. See the section on "Connecting
Cables to Terminals".
The values of Volume offset are low.
Increase the values of Volume offset. (see p. 15)
Press the reset button on the unit (see page 4).
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally.
A speaker cable may be pinched by a screw in the car.
The speakers are not wired correctly.
Check the speaker wiring.
The sound quality is poor or
distorted.
Reconnect the speaker cables so that each output
terminal is connected to a different speaker.
Radio reception is poor.
The car antenna is not extended.
Pull out the antenna all the way.
The antenna control cable is not connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The memory is erased when
the ignition is turned off.
The battery cable has not been connected to the proper
terminal.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The ignition and battery cable are incorrectly connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function does
not work.
The TEL mute cable is not connected properly.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function turns
on even though the TEL mute
cable is not connected.
The TEL mute cable is touching a metal part of the car.
Pull the TEL mute cable away from the metal part of the
car.
A CD ejects as soon as it is
loaded.
The CD is upside-down.
The CD is quite dirty.
Load the CD with the labelled side up.
Clean the CD, referring to the section on "Cleaning CDs"
(see page 6).
— 41 —
Troubleshooting Guide
PROBLEM
POSSIBLE CAUSE
SOLUTION
The sound skips on a CD.
The CD is scratched or dirty.
Clean the CD, referring to the section on "Cleaning CDs"
(see page 6).
The specified track does not
play.
Random play has been selected.
Turn off the random play function.
Egnlish
Can’t remove disc.
The cause is that more than 10 minutes has elapsed
since the vehicle ACC switch was turned OFF.
The disc can only be removed within 10 minutes of the
ACC switch being turned OFF. If more than 10 minutes
has elapsed, turn the ACC switch ON again and press
the Eject button.
Free switching of the sound
quality.
The system Q function is set on Scan mode.
The system Q function is set on Scan mode.
Refer to the “System Q” page and switch it to a
function other than Scan mode. (see p. 12).
Audio control setting cannot be
achieved.
Refer to the “System Q” page and switch it to a
function other than Scan mode.(see p. 12).
CD/External disc control mode
The disc control mode cannot
be selected.
No cable has been connected to the disc changer input
terminal on the unit.
Connect the cable to the disc changer input terminal on
the unit.
The specified disc does not
play, but another one plays
instead.
The specified CD is very dirty.
The CD is upside-down.
Clean the CD.
Load the CD with the labelled side up.
The disc is loaded in a different slot from that specified.
Eject the disc magazine and check the number for the
specified disc.
The disc is severely scratched.
Try another disc instead.
The sound skips.
Something is touching the disc changer.
The CD is scratched or dirty.
Remove whatever is touching it.
If skipping happens at the same place when the car is
stopped, something is wrong with the CD. Clean the CD.
The display shows that the
changer is being played, but no
sound can be heard.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see page 4).
The specified track does not
play.
Random play or magazine random play has been
selected.
Turn off the random play or magazine random play
function.
Track repeat, disc repeat, track
scan, random play, and magazine
random play start by themselves.
The setting is not cancelled.
The settings for these functions remain on until the
setting to off or the disc ejected, even if the power is
turned off or the source changed.
Cannot play CD-R or CD-RW
Finalization processing is not being conducted for CD-
R/CD-RW.
Conduct finalization processing with CD recorder.
A non-compatible CD changer is being used to play the
CD-R/CD-RW.
Use a CD changer compatible with CD-R/CD-RW to play.
— 42 —
The following messages are displayed when certain problems are occurring in your system. Take the
recommended actions.
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.
Eject
]
Load the disc magazine properly.
No CD in the unit.
]
Insert the CD.
No disc has been loaded in the disc magazine.
NO DISC
TOC Error
]
Load a disc into the disc magazine.
No disc has been loaded in the disc magazine.
]
Load a disc into the disc magazine.
The CD is very dirty. The CD is upside-down. The CD is scratched a lot.
]
Clean the CD and load it correctly.
Nothing has been recorded on the MD.
Blank Disc
No Tr Disc
NO PANEL
No tracks are recorded on the MD, although it has a title.
The faceplate of the slave unit being connected to this unit has been removed.
]
Replace it.
The unit is malfunctioning for some reason.
E-77
]
Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.
Mecha Error
]
Check the disc magazine. And then, press the reset button on the unit.
If the "Mecha Error" code does not disappear, consult your nearest service center.
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),
stopping all operation.
Hold Error
IN
]
Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),
the disc starts playing again.
If this indicator blinks, the CD player is malfunctioning.
] Eject the CD and try inseting it again.
If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected.
If the following situations, consult your nearest service centre:
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is
entered when switching modes.
— 43 —
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency range (50 kHz space) ..............87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB) .................................0.7 µV/75 ½
Quieting Sensitivity (S/N = 46dB) ..............................1.6 µV/75 ½
Frequency response ( 3 dB).................................30 Hz – 15 kHz
Signal to Noise ratio (MONO)..............................................65 dB
Selectivity (DIN) ( 400 kHz)..............................................³ 80 dB
Stereo separation (1 kHz) ....................................................35 dB
Maximum output power.................................................47 W ´ 4
Output power (DIN 45324, +B=14.4V)...........................29 W ´ 4
Tone action
Egnlish
Bass : ..........................................................100 Hz 10 dB
Middle : .........................................................1 kHz 10 dB
Treble :.........................................................10 kHz 10 dB
Preout level / Load (during disc play)....................1800 mV/10 k½
Preout impedance (during disc play) ................................² 600 ½
MW tuner section
Frequency range (9 kHz space) .....................531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB) ...........................................25 µV
General
Operating voltage (11 – 16V allowable) ..............................14.4 V
Current consumption.............................................................10 A
Installation Size (W x H x D) ..........................182 ´ 53 ´ 162 mm
Weight ................................................................................1.7 kg
LW tuner section
Frequency range .............................................153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB) ...........................................45 µV
CD player section
Laser diode....................................................GaAlAs (l=780 nm)
Digital filter (D/A)......................................8 Times Over Sampling
D/A Converter .......................................................................1 Bit
Spindle speed...............................................500 – 200 rpm (CLV)
Wow & Flutter........................................Below Measurable Limit
Frequency response ( 1 dB).................................10 Hz – 20 kHz
Total harmonic distortion (1 kHz) ......................................0.01 %
Signal to Noise ratio (1 kHz) ................................................93 dB
Dynamic range ....................................................................93 dB
Channel separation..............................................................85 dB
— 44 —
|