Kenwood DPX 6030 User Manual

DOUBLE DIN SIZED CD/CASSETTE RECEIVER  
DPX-6030  
DPX-6020  
INSTRUCTION MANUAL  
© PRINTED IN JAPAN B64-2004-10 (M) (+)  
03/ 2 1 02/12 11 10 9 8 7 6 5 4 3 2  
Safety precautions  
IMPORTANT INFORMATION  
About the disc changer to be  
connected:  
To connect a disc changer having the "O-N"  
switch to this unit, set the "O-N" switch to  
"N".  
When you connect a model with no "O-N"  
switch, the converter cord CA-DS100  
available as an option may be required. For  
details, consult your Kenwood dealer.  
If a model with no "O-N" switch is connected,  
some unavailable functions and information  
that cannot be displayed are generated, such  
as the DNPS, DNPP, Magazine random play,  
and CD Text display.  
2WARNING  
2CAUTION  
To prevent injury or fire, take the  
following precautions:  
• Insert the unit all the way in until it is fully  
locked in place. Otherwise it may fall out of  
place when jolted.  
To prevent damage to the machine,  
take the following precautions:  
• Make sure to ground the unit to a negative  
12V DC power supply.  
• Do not open the top or bottom covers of the  
unit.  
• Do not install the unit in a spot exposed to  
direct sunlight or excessive heat or humidity.  
Also avoid places with too much dust or the  
possibility of water splashing.  
• Do not subject the faceplate to excessive  
shock, as it is a piece of precision equipment.  
• When replacing a fuse, only use a new one  
with the prescribed rating. Using a fuse with  
the wrong rating may cause your unit to  
malfunction.  
• When extending the ignition, battery, or  
ground wires, make sure to use automotive-  
2
grade wires or other wires with a 0.75mm  
(AWG18) or more to prevent wire  
deterioration and damage to the wire coating.  
• To prevent a short circuit, never put or leave  
any metallic objects (such as coins or metal  
tools) inside the unit.  
• If the unit starts to emit smoke or strange  
smells, turn off the power immediately and  
consult your Kenwood dealer.  
Note that none of the KDC-C100, KDC-C302,  
C205, C705, and non-Kenwood CD changers  
can be connected.  
• Make sure not to get your fingers caught  
between the faceplate and the unit.  
• Be careful not to drop the unit or subject it to  
strong shock.  
The unit may break or crack because it  
contains glass parts.  
• To prevent a short circuit when replacing a  
fuse, first disconnect the wiring harness.  
• Do not place any object between the  
faceplate and the unit.  
• Do not use your own screws. Use only the  
screws provided. If you use the wrong  
screws, you could damage the unit.  
2CAUTION  
You can damage both your unit and  
the CD changer if you connect them  
incorrectly.  
NOTE  
The illustrations of the display and the panel  
appearing in this manual are examples used  
to explain more clearly how the controls are  
used. Therefore, what appears on the display  
in the illustrations may differ from what  
appears on the display on the actual  
equipment, and some of the illustrations on  
the display may represent something  
impossible in actual operation.  
Manufactured under license from Dolby  
Laboratories.  
“Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
— 3 —  
Safety precautions  
volatile liquid such as thinner or alcohol may  
scratch the surface or erases characters.  
• Remove a cassette tape from the unit when  
not listening to it for a while. If you leave a  
tape in the unit too long, it may stick to the  
tape head and cause unit malfunction.  
NOTE  
• CD-Rs and CD-RWs which have not  
undergone finalization processing cannot be  
played. (For more information on finalization  
processing, refer to the manual for your CD-  
R/CD-RW writing software or CD-R/CD-RW  
recorder.) Additionally, depending on the  
recording status, it may prove impossible to  
play certain CDs recorded on CD-R or CD-RW.  
The marking of products using lasers  
(Except for some areas)  
Cleaning the Tape Head  
After you have listened to many cassettes  
over a long period of time, magnetic powder  
from the tapes and dust accumulates on the  
tape head, causing noise and a deterioration  
in sound quality. Clean the tape head using a  
cleaning tape or cleaning kit designed for use  
in car audio systems.  
CLASS 1  
LASER PRODUCT  
• If you experience problems during  
installation, consult your Kenwood dealer.  
• If the unit does not seem to be working right,  
try pressing the reset button first. If that does  
not solve the problem, consult your Kenwood  
dealer.  
The label is attached to the chassis/case and  
says that the component uses laser beams  
that have been classified as Class 1. It means  
that the unit is utilizing laser beams that are  
of a weaker class. There is no danger of  
hazardous radiation outside the unit.  
Cleaning the CD Slot  
As dust tends to accumulate in the CD slot,  
clean it every once in a while. Your CDs can  
get scratched if you put them in a dusty CD  
slot.  
Handling Cassette Tapes  
• Do not play a cassette whose tape has gone  
slack. In such a case, wind it tight using a  
pencil or the like in one of the spools. Playing  
slack cassette tapes can result in the tape  
tangling around the capstan and/or pinch  
rollers, causing trouble.  
DISP  
• Do not play a deformed cassette or one  
whose label is starting to come off, as it can  
cause the unit to malfunction.  
• Do not leave tapes in hot places, such as on  
dashboards and other spots exposed to  
direct sunlight, or near heater outlets. They  
can deform the cassette.  
• Avoid using extremely long cassette tapes,  
such as 100-minute-long tapes. Such tapes  
are very thin, and can tangle easily around  
the pinch rollers or other parts inside the unit,  
causing unit failure.  
Reset button  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it  
with a dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the  
stain off with a cloth moistened with neutral  
cleaner, then wipe neutral detergent off.  
Lens Fogging  
Right after you turn on the car heater in cold  
weather, dew or condensation may form on  
the lens in the CD player of the unit. Called  
lens fogging, CDs may be impossible to play.  
In such a situation, remove the disc and wait  
for the condensation to evaporate. If the unit  
still does not operate normally after a while,  
consult your Kenwood dealer.  
2CAUTION  
Applying spray cleaner directly to the unit  
may affect its mechanical parts. Wiping the  
front panel with a hard cloth or using a  
— 4 —  
Handling Compact discs  
Playing a CD that is dirty, scratched  
or warped can cause the sound to  
skip and the unit to operate  
incorrectly, resulting in worsened  
sound quality. Take the following  
precautions to prevent your CDs from  
getting scratched or damaged.  
Storing CDs  
• Do not store CDs in areas exposed to direct  
sunlight (such as a car seat or the dashboard)  
or other hot places.  
A CD-R or CD-RW is more susceptible than a  
music CD to damage from high temperatures  
and humidity, and in some cases, may  
become unusable if left in the car for long  
periods of time.  
Checking New CDs for Burrs  
When playing a new CD for the first time, check  
that there are not any burrs stuck to the  
perimeter of the disc or in the central hole. CDs  
with burrs stuck on them may not load properly  
or may skip while playing. Remove burrs using  
a ballpoint pen or a similar utensil.  
• Remove CDs from the unit when not listening  
to them for a while, and put them back in their  
cases. Do not pile up CDs that are removed  
from their cases or prop them against  
something.  
Handling CDs  
• Do not touch the recorded side of the CD (the  
side opposite the label) when holding it.  
Burrs  
Burrs  
Cleaning CDs  
If a CD has gotten dirty, wipe it off gently using  
a commercially available cleaning cloth or a soft  
cotton cloth, starting from the center of the disc  
and moving outward. Do not clean CDs with  
conventional record cleaners, anti-static  
formulas, or chemicals such as paint thinner or  
benzene.  
• The reflective film on a CD-R or a CD-RW is  
more fragile than that on an ordinary music CD,  
and may peel off if scratched. Fingerprints on a  
CD-R or CD-RW are also more likely to cause  
skipping when the disc is played. For these  
reasons, handle the disc very carefully. Detailed  
handling instructions will appear on the CD-R or  
CD-RW package: read this information carefully  
before using the disc.  
Removing the CD  
Only remove the CD from the machine in a  
horizontal direction, holding it flat. You may  
damage the surface of the CD if you try pulling  
it down as it ejects.  
• Do not stick tape on either side of the CD.  
Tape  
Do Not Use Special Shape CDs  
• Be sure to use round shape CDs only for this  
unit and do not use any special shape CDs.  
Use of special shape CDs may cause the unit  
to malfunction.  
Do Not Use CDs with Sticker on the  
Labeled Side  
Do not use the CD with the label sticker stuck  
on it.  
Using such a CD may cause the CD to be  
deformed and the sticker to peel off, resulting  
in malfunction of the unit.  
Do Not Load CD Accessories  
Do not use commercially available CD  
accessories that can be loaded into the CD slot,  
such as stabilizers, protective sheets, or CD  
cleaning discs, since they can cause the unit to  
malfunction.  
• Be sure to use CDs with disc mark  
only for this unit.  
— 5 —  
General features  
Power  
5ANGLE RTN  
4 ¢  
5
ATT  
FM  
Turning on the power:  
Press the SRC (source) button.  
NOTE  
Turn the power on before carrying out the following procedures.  
Turning off the power:  
Press the PWR OFF button for at least one second.  
Switching Modes  
DISP  
Switching Modes:  
Each time you press the SRC (source) button, the mode  
switches as follows:  
Tuner mode  
ANGLE∞  
SRC/PWR OFF  
AM  
DISP  
Tape mode  
AUD  
CD mode  
External disc control mode  
Standby mode  
Selecting standby mode:  
Press the SRC button repeatedly and switch to "ALL OFF".  
When "ALL OFF" is displayed, the standby mode is activated.  
The standby mode turns all functions off while leaving the  
power to the unit on. Use this mode when you want to have  
the display illuminated but don't want to listen to anything.  
NOTE  
• The mode switches to the next mode from any mode which  
cannot be used.  
• The external disc control mode will differ depending on the unit  
that is connected.  
ATT indicator  
Clock display  
— 6 —  
Volume  
Audio Control Setting  
Adjust various sound levels.  
Increasing Volume:  
Press the 5 button to turn up the volume.  
1
2
Press the AUD button twice to enter the control mode.  
Decreasing Volume:  
Press either the 4 or ¢ button.  
Press the button to turn down the volume.  
Each time the button is pressed, the adjustment mode will  
change as follows:  
Pressing the ¢ button advances the display, and pressing the  
4 button reverses it.  
Attenuator  
"Balance"  
This function allows you to turn down the volume quickly.  
"Fader"  
"N-F" (only when being switched)  
Turning Attenuator On/Off:  
Press the ATT button to switch the attenuator on and off.  
When the attenuator is on, the ATT indicator blinks.  
When the attenuator is off, the volume returns to the original  
level.  
3
Press the FM/AM button.  
Look at the table to adjust the mode being displayed.  
Adjustment  
mode  
(Display)  
Operation of Audio control button  
NOTE  
AM button  
FM button  
Turning the volume all the way down deactivates the attenuator  
function.  
Balance  
("Balance")  
Left channel emphasized.  
Right channel emphasized.  
Fader  
("Fader")  
Rear channel emphasized. Front channel emphasized.  
Adjusting Clock  
Adjust the clock.  
Non-Fading  
Preout Level  
("N-F")  
Non-fading sound  
reduced.  
Non-fading sound  
emphasized.  
1
When the clock is not displayed, first press the DISP button to  
display "Clock".  
4
2
Press the AUD button to end the control mode.  
Press the DISP button for at least two seconds to enter the  
clock adjustment mode.  
3 • Adjusting the hours  
Press the FM button to advance the hours, or press the AM  
button to make the hours go back.  
• Adjusting the minutes  
Press the ¢ button to advance the minutes, or press the  
4 button to make the minutes go back.  
Press the DISP button to end the clock adjustment mode.  
4
— 7 —  
General features  
Panel Angle Adjustment  
You can adjust the panel angle for easy viewing.  
Switching Display  
You can switch the display during the standby mode as  
mentioned below.  
Sliding the panel:  
Switching the Display During the Standby Mode:  
Each time you press the DISP button during the standby mode,  
the display switches as follows:  
Press the ANGLEbutton.  
Each time you press the ANGLEbutton, the panel will slide  
one step at a time.The faceplate angle can be varied in up to  
ten steps.  
Character with graphic display  
Clock with graphic display  
Clock  
NOTE  
If the power is turned off, the panel will close automatically.  
When you turn the power back on, the panel angle will return to  
the adjusted angle position.  
Closing the panel:  
Press the 5ANGLE RTN button to close the panel.  
NOTE  
The sound will be muted while the panel is sliding during the tape  
mode.  
2CAUTION  
• Take care that your fingers and so on do not get caught during  
the slide operation of the front panel.  
• When the front panel has been slid, it might interfere with the  
shift lever or something else. If this happens, pay attention to  
safety and move the shift lever or take an appropriate action,  
then operate the unit.  
• Do not apply excessive force to the front panel after it slides.  
— 8 —  
Tuner features  
Tuning  
CRSC  
¢
4
FM  
1
Press the SRC (source) button repeatedly to select the tuner  
mode. "TUNER" is displayed when the tuner mode has been  
selected.  
2
Press either the FM or AM button to select the band.  
Each time you press the FM button, the band switches  
between the FM1, FM2 and FM3.  
Press the AM button to select the AM band.  
3
• Auto Seek Tuning  
Press the ¢ button to seek higher frequencies.  
Press the 4 button to seek lower frequencies.  
• Manual Tuning  
DISP  
Press the ¢ button to increase the frequency by one step.  
Press the 4 button to decrease the frequency by one step.  
NOTE  
•The ST indicator lights up when stereo broadcasts are being  
received.  
• Please see the function set system about selecting tuning  
mode. (page 33)  
38  
SRC  
SBF  
#1~6  
AM  
DISP/  
NAME  
ST indicator  
AUTO indicator  
Station Preset Memory  
Store the frequency of a station. You can then recall that  
station with a single touch of a button.  
1
2
Select the band/ station that you want to have stored.  
Press the button (#1-6) that you want to use for the station, for  
at least two seconds.  
The button number blinks once in the display to indicate that  
the data has been stored.  
NOTE  
You can store six stations in each of the FM1, FM2, FM3, and AM  
bands.  
Frequency  
Band display  
Preset station number  
indicator  
— 9 —  
Tuner features  
Preset Tuning  
You can recall a station being preset in preset station buttons  
(#1-6).  
Switching Display for Tuner  
You can change the display used when listening to the radio.  
Changing the Display:  
Recalling a Preset Station:  
Each time you press the DISP button, the display changes as  
follows:  
Press the preset station button (#1-6) for the desired station.  
The number of the recalled station is displayed.  
Station frequency  
"SNPS"  
Clean Reception System Circuit (CRSC)  
"Character"  
"Clock"  
Temporarily have reception switched from stereo to mono to  
reduce multi-path noise when listening to the FM station.  
The  
indicator lights up when CRSC is off.  
Turning CRSC On/Off:  
Press the CRSC button for at least one second to turn the  
function on/off.  
Direct Access Tuning  
(Function of remote control)  
NOTE  
When you know the frequency of the station that you want to  
Strong electrical fields (such as from power lines) may cause  
unstable sound quality when CRSC is turned on. In such a  
situation, turn it off.  
listen to, you can input it directly for quick access.  
1 Select the band by pressing the FM or AM button.  
2 Press the DIRECT button.  
"----" is displayed for 10 seconds.  
If you make no input in the 10-second period, direct access  
tuning is automatically cancelled.  
Frequency Step Setting  
Switch the frequency step used in seeks. The factory defaults  
are 50 kHz for FM and 9 kHz for AM.  
3 Enter the frequency of the desired station.  
If you want to listen to an FM station at 92.1 MHz, for example,  
press 9, 2, and 1.  
1
2
Turn the power off.  
If you want to listen to an AM station at 810 kHz, for example,  
press 8, 1, and 0.  
While pressing the button #1, press the button #5. Hold down  
both of these buttons, then press the SRC button.  
The frequency step settings will be changed to 200 kHz for FM  
and 10 kHz for AM.  
NOTE  
• You cannot enter frequencies above or below what a band can  
NOTE  
receive.  
• FM frequencies can only be input in 0.1 MHz steps, and not  
0.01MHz steps.  
When you change the frequency step settings, part of memory  
contents (except for SNPS) will be erased.  
Cancelling Direct Access Tuning:  
Returning Frequency Step Settings to Original Values:  
Press the DIRECT button again.  
Repeat steps 1 and 2 above.  
— 10 —  
Station Name Preset (SNPS)  
Character  
Button to press  
# Times pressed  
You can assign names to radio stations with the Station Preset  
#3  
#2  
#6  
#2  
#3  
1
1
2
3
2
“D”  
“A”  
“N”  
“C”  
“E”  
Memory. Up to 30 stations can be assigned names.  
1
Adjust the frequency to the station whose name you want to  
enter.  
NOTE  
This function cannot be available during the clock display.  
2
Press the NAME button for at least two seconds.  
“Name Set” is displayed once the station name preset mode is  
entered.  
5
Continue steps 3 and 4 until all the characters are chosen for  
the name.  
The cursor will blink in the position where letters are entered.  
NOTE  
3
4
Press either the 4 or ¢ button to move the cursor to the  
desired position.  
You can enter up to 8 characters for each name.  
The 4 button moves the cursor to the left, and the ¢  
6
Assigning Names  
button to the right.  
You can also move the cursor left or right by pressing the 4  
or ¢ buttons, respectively, on the remote.  
Press the NAME button on the unit or the OK button on the  
remote.  
The name of the station is stored in memory, and the Station  
Name Preset mode ends.  
Each time the 38 button is pressed, the characters to be  
entered change as listed below.  
Also, if you make no input for 10 seconds, the name will be  
stored up to the point that you have entered, and the mode  
ends.  
Press the FM or AM button to display the desired character.  
Characters that can be displayed are as follows.  
NOTE  
Alphabet (upper case): _ A ~ Z  
• You can assign names to up to 30 FM/AM stations in all.  
• Station names remain stored even if the reset button is pressed.  
• If you want to change the name of a station, first display the  
name of the station (following steps 1 and 2 above), then  
change the letter(s) that you want by following steps 3 and 4.  
Alphabet (lower case): _ a ~ z  
Numerals and symbols: _ 0~9 / + - = & " ˚ ' < > [ ]  
NOTE  
Direct Alphabet Input  
(Function of remote control with number/letter entry buttons)  
Direct input can be made of letters (alphabetical) with the letter  
entry buttons on the remote control.  
Example: Use the following table to enter the name "DANCE".  
— 11 —  
Tuner features  
Cassette player features  
Station Name Preset Play (SNPP)  
You can search for the station for any station if its name has  
been preset using Station Name Preset.  
CASSETTE EJECT  
4 ¢  
FM  
1
Press the SBF button for at least one second.  
“SBF SNPS” will be displayed once the station name preset  
play mode is entered.  
The names of the stations stored in the band currently listened  
to are displayed in the following order for five seconds each:  
= FM1 Ô FM2 Ô FM3 Ô AM +  
Each time you press the ¢ button, the station display  
switches in the forward direction.  
Each time you press the 4 button, the station display  
DISP  
switches in the reverse direction.  
Stations whose names have not been stored will be displayed  
as frequencies.  
NOTE  
Changing the Displayed Band  
Pressing the FM button switches between the FM1, FM2, FM3  
displays, in that order.  
Pressing the AM button switches to the AM display.  
38  
SRC  
MTL  
B NR  
SCN  
AM  
B.S  
DISP  
REP  
2
Once the name is displayed for the station you want to listen  
to  
Press the SBF button.  
Reception starts of the displayed station, and the station name  
preset play mode ends.  
B.S indicator  
SCN indicator  
Canceling mode during input:  
Press the SBF button for at least one second.  
The station name preset play mode is canceled.  
Mode display  
indicator  
B NR indicator  
Tape counter  
MTL indicator  
REP indicator  
— 12 —  
Playing Cassette Tapes  
Fast Forwarding and Rewinding Cassette Tapes  
Loading and Playing Cassettes:  
Fast Forwarding Tapes:  
Press the CASSETTE EJECT button to slide open the front  
panel, showing the cassette (insertion) slot. Holding the  
cassette with the tape exposed to the right, insert in the slot.  
The front panel will close, and the tape will start playing.  
Press the FM button.  
Rewinding Tapes:  
Press the AM button.  
Canceling:  
The  
indicator lights up when a cassette has been loaded.  
Press the 38 button.  
Playing Cassettes Already Loaded:  
Press the SRC (Source) button repeatedly to select the tape  
mode. "TAPE" is displayed when the tape mode has been  
selected.  
Normal tape play will begin.  
The tape will start playing.  
Using Dolby B Noise Reduction  
Listen to tapes recorded using Dolby B NR.  
Listening to the other side:  
Press the 38 button.  
Tape play switches to the other side.  
Turning Dolby B Noise Reduction On/Off:  
Eject:  
Press the B NR button to switch Dolby B NR on and off.  
The B NR indicator lights up when it is turned on.  
Press the CASSETTE EJECT  
button to stop tape play. The  
front panel will slide to eject the  
tape.  
Press the CASSETTE EJECT  
button to close the front panel.  
Switching Tape Types  
Select type of tape being played.  
Switching Tape Types:  
NOTE  
Press the MTL button to switch the metal tape indicator on and  
off and to select the tape type.  
Remove a cassette from the unit when not listening to it for a  
while. If you leave it in the unit too long, the tape may stick to the  
tape head and cause the unit to malfunction.  
Turn the MTL indicator off for normal tape (Type I) playback.  
Turn the MTL indicator on for the following tape types:  
2CAUTION  
2
CrO (Type II) FeCr (Type III) Metal (Type IV)  
• Take care that your fingers and so on do not get caught during  
the slide operation of the front panel.  
Selecting the wrong tape type may cause sound quality to  
suffer.  
• When the front panel has been slid open, it might interfere with  
the shift lever or something else. If this happens, pay attention  
to safety and move the shift lever or take an appropriate action,  
then operate the unit.  
• Do not apply excessive force to the front panel after it slides.  
• Do not use the unit with the front panel in the slid condition.  
Doing so will cause breakdown.  
— 13 —  
Cassette player features  
Using Direct Program Search System (DPSS)  
Skip forward or backward to other tracks during playback.  
1 Enter the number of tracks you want to skip using the numeric  
buttons on the remote control.  
Up to 9 tracks can be skipped.  
Skipping to Beginning of Current Track or to Previous Tracks  
(Rewind DPSS):  
2 Press either the 4 or ¢ button while the number is  
displayed, depending on whether you want to skip backwards  
or forwards.  
Press the 4 button.  
Press once to rewind to the beginning of the current track,  
twice to rewind to the beginning of the previous track, and so  
forth.  
Playback starts after the tape rewinds or fast forwards by the  
specified number of tracks.  
NOTE  
You can skip up to nine tracks.  
Playback is continued after the tape is rewind by the indicated  
number of tracks.  
• During the first five seconds of each track, the previous track is  
considered the "current" track. If you press the 4 button  
during that period, the tape rewinds to the beginning of the  
previous track and not the one you are listening to.  
• The DPSS function "knows" where a track begins by detecting  
the blank space preceding it (the space between tracks).  
However, when the blank space lasts for less than four seconds  
or contains noise, this function may not operate correctly.  
Furthermore, sections that are recorded at low levels may  
trigger the function if they last for four seconds or more.  
Skipping to Later Tracks (Fast Forward DPSS):  
Press the ¢ button.  
Press once to fast forward to the next track, twice to fast  
forward to the track after that, and so forth.  
You can skip up to nine tracks.  
Playback is continued after the tape is fast forwarded by the  
indicated number of tracks.  
NOTE  
Cancelling DPSS During Its Operation:  
• During the first five seconds of each track, the previous track is  
considered the "current" track. If you press the 4 button  
during that period, the tape rewinds to the beginning of the  
previous track and not the one you are listening to.  
Press the 38 button.  
• The DPSS function "knows" where a track begins by detecting  
the blank space preceding it (the space between tracks).  
However, when the blank space lasts for less than four seconds  
or contains noise, DPSS may not operate correctly. Furthermore,  
quiet intervals within a song are detected as "blank spaces" if  
they last for four seconds or more.  
Blank Skip  
Automatically fast forward to the beginning of the next track  
when long blank spaces (10 seconds or more) are detected,  
continuing tape playback. The B.S indicator lights up when  
blank skip is turned on.  
Canceling DPSS While It is Operating:  
Press the 38 button.  
Turning Blank Skip On/Off:  
Press the B.S button to switch blank skip on and off.  
NOTE  
• If the blank space contains much noise, the blank skip function  
may not work right.  
• Sections recorded at low levels may trigger the blank skip  
function if they last for 10 seconds or more.  
Using DPSS with Remote  
Directly input the number of tracks to skip during playback.  
— 14 —  
Index Scan  
Switching Display  
Successively plays the first ten seconds of each track on the  
Switching the display during the tape mode:  
Each time you press the DISP button, the display switches as  
follows:  
tape.  
Turning Index Scan On/Off:  
Press the SCN button to switch index scan on/off.  
The SCN indicator lights up when index scan is turned on.  
Tape counter  
"Character"  
"Clock"  
Stopping to Listen to the Track Being Scanned:  
Press either the SCN or 38 button.  
Playback begins as usual.  
NOTE  
• Index scan is canceled when the tape stops.  
NOTE  
• Index scan "knows" where a track begins by detecting the blank  
space preceding it (the space between tracks). However, when  
the blank space lasts for less than 4 seconds or contains noise,  
this function may not operate correctly. Furthermore, sections  
that are recorded at low levels may trigger the function if they  
last for 4 seconds or more.  
The tape counter is not exact, but only represents an  
approximation of the elapsed time.  
Music Repeat  
Repeatedly plays the track currently being listened to.  
Turning Music Repeat On/Off:  
Press the REP button to switch music repeat on/off.  
The REP indicator lights up when music repeat is turned on.  
Canceling Music Repeat:  
Press either the REP or 38 button.  
NOTE  
Music repeat "knows" where a track begins by detecting the blank  
space preceding it (the space between tracks). However, when  
the blank space lasts for less than four seconds or contains noise,  
this function may not operate correctly. Furthermore, sections  
that are recorded at low levels may trigger the function if they last  
for four seconds or more.  
— 15 —  
CD/External disc control features  
Playing CDs  
CD EJECT  
4 ¢  
DISC+  
Play:  
Press the CD EJECT button to slide open the front panel,  
showing the CD (insertion) slot. Holding the CD with the  
labeled side facing up, insert it in the slot. The front panel will  
close, and the CD will start playing.  
The  
indicator will light when a CD has been inserted.  
Playing CDs Already Inserted:  
Press the SRC button repeatedly to select the CD mode.  
"CD" is displayed when the CD mode has been selected.  
The CD will start playing.  
Pausing and Restarting CD Play:  
Press the 38 button to make the disc pause.  
DISP  
Press the same button again to start play again.  
Eject:  
Press the CD EJECT button.  
The front panel will slide to  
eject the CD.  
Press the CD EJECT button to  
close the front panel.  
38  
SRC  
SBF  
D.SCN  
SCRL  
SCN  
DISC-  
RDM  
DISP/  
NAME  
REP  
M.RDM  
SCN/D.SCN indicator  
NOTE  
REP/D.REP indicator  
When the CD cannot be ejected  
even if you press the CD EJECT button, press this button for at  
least three seconds to eject the CD.  
2CAUTION  
• Do not attempt to insert a CD into the slot if another one is  
already there.  
• The eject function will operate even if the CD EJECT button is  
pressed while no CD is loaded. Attempting to quickly insert a  
CD at this time may result in scratching the CD. Wait a short  
time before inserting a CD.  
• When the front panel has been slid, it might interfere with the  
shift lever or something else. If this happens, pay attention to  
safety and move the shift lever or take an appropriate action,  
then operate the unit.  
indicator  
RDM/M.RDM indicator  
Mode display/  
Disc number  
Track  
number  
Track time  
— 16 —  
• Do not apply excessive force to the front panel after it slides.  
• Do not use the unit with the front panel in the slid condition.  
Doing so will cause breakdown.  
Switching Display for Discs  
Switch the display that appears while discs are playing.  
NOTE  
Switching Display for Discs:  
Each time you press the DISP button, the display during disc play  
switches as follows.  
When you load a CD and eject it right away, the next time you try  
to insert the CD may not load. In such a situation, take the CD out  
for a moment and then reinsert it.  
"P-Time" (Track playing time)  
"A-Time" (Total disc playing time (CD only))  
"DNPS" (Disc name)  
Playing Other Disc mode  
This function permits the connection of optional players and  
the playing of discs other than the loaded CD (in the current  
unit).  
"Disc title" (Units featuring CD text/MD only)  
"Track title" (Units featuring CD text/MD only)  
"Character"  
Playing Discs:  
"Clock"  
Press the SRC button repeatedly to select the external disc  
control mode.  
The disc will start playing.  
NOTE  
NOTE  
• You can give names to discs through the presetting disc name  
function (see p.22), depending on the unit.  
Note that depending on the unit, display may not be possible.  
• If you try to display the name of a disc that does not have one,  
"No Name" is displayed instead.  
• When there is an attempt to display the title of a disc for which  
the disc title/track title has not been recorded, "No Text" is  
displayed for CD and "No Title" is displayed for MD.  
• Depending on the type of characters of the CD text, some  
characters may not be displayed.  
The external disc control mode will differ, depending on the unit  
that is connected.  
Mode Display Examples  
• "DISC/CD/MD-CH"...when a disc changer is connected  
• "DISC/CD/MD-CH1", "DISC/CD/MD-CH2"...when two disc  
changers are connected  
Pausing and Restarting Disc Play:  
Press the 38 button to make the disc pause.  
Press the same button again to start play again.  
NOTE  
When one disc has finished playing its last track, the next disc in  
the changer will start playing. When the last disc in the changer  
has finished, the player will return to the first disc and start  
playing it.  
— 17 —  
CD/External disc control features  
Fast Forwarding and Reversing Disc Play  
Disc Search  
Search forward or backward through the discs in a disc  
changer.  
(Function of disc changers)  
Fast Forwarding Disc Play:  
Hold down on the ¢ button.  
Release your finger to play the disc at that point.  
Making a Reverse Disc Search:  
Press the DISCbutton to display the desired disc number.  
Each time the button is pressed, the displayed disc number  
decreases by one.  
Reversing Disc Play:  
Hold down on the 4 button.  
Release your finger to play the disc at the point.  
NOTE  
Play starts at the beginning of the displayed disc.  
Making a Forward Disc Search:  
You cannot use reverse play between tracks depending on the  
model being connected. Instead, the reverse play function is  
canceled when it reaches the beginning of a track, at which point  
normal play will automatically resume.  
Press the DISC+ button to display the desired disc number.  
Each time the button is pressed, the displayed disc number  
increases by one.  
Play starts at the beginning of the displayed disc.  
NOTE  
"LOAD" is displayed when discs are being exchanged on the disc  
changer.  
Track Search  
Search forward or backward through the tracks on the disc until  
you reach the one that you want to listen to.  
Making a Reverse Track Search:  
Direct Track Search  
Using the remote, directly input the track number that you want  
to listen to.  
(Function of Remote) (See page 36)  
Press the 4 button to display the desired track number.  
Press once to search back to the beginning of the current track,  
twice to search back to the beginning of the previous track, and  
so forth.  
1
Using the number buttons on the remote, input the number of  
the track that you want to listen to.  
Play starts at the beginning of the displayed track number.  
NOTE  
The selected track number will blink in the display for 10  
seconds.  
(For disc changers)  
Pressing the 4 button while listening to track 1 will only search  
back to the beginning of that track. The reverse search is not  
"recycled" to the last track on the disc.  
If you make no further input in the 10-second period, the  
number entry mode will automatically be canceled.  
2
Press either the 4 or ¢ button while the track number is  
Making a Forward Track Search:  
blinking.  
Press the ¢ button to display the desired track number.  
Press once to fast forward to the next track, twice to fast  
forward to the track after that, and so forth.  
The track starts playing.  
Canceling Direct Track Search While It Is Operating:  
Play starts at the beginning of the displayed track number.  
Press the 38 button.  
NOTE  
(For disc changers)  
You cannot make a forward track search when listening to the last  
track on a disc.  
— 18 —  
NOTE  
Track / Disc Repeat  
Repeat playing the track or the disc currently being listened to.  
You cannot use the direct track search function while doing track  
or disc scans or using random or magazine-random play.  
Turning Repeat Play On/Off:  
Press the REP button to switch repeat track/disc play on and  
off as follows:  
Track Repeat ON  
Direct Disc Search Function of disc changers with remote  
(See page 36)  
Disc Repeat ON (Function of disc changers)  
Using the remote, directly input the disc number that you want  
to listen to.  
Track/Disc Repeat OFF  
1
Using the number buttons on the remote, input the number of  
the disc that you want to listen to.  
The REP indicator lights up in the display when track repeat is  
on.  
The selected disc number will blink in the display for 10  
seconds.  
The D.REP indicator lights up in the display when disc repeat is  
on.  
If you make no further input in the 10-second period, the  
number entry mode will automatically be canceled.  
NOTE  
Repeat play is canceled when you stop playing the disc.  
NOTE  
If you input more than two numbers all at once, a search will be  
made only of the last number input.  
2
Press either the DISC+ or DISCbutton while the number  
inputted is blinking.  
The disc starts playing.  
Track Scan  
Canceling Direct Disc Search While It Is Operating:  
Successively play the beginning of each track on a disc until  
you find the track that you want to listen to.  
Press the 38 button.  
Starting the Track Scan :  
Press the SCN button. The SCN indicator lights up and the first  
10 seconds of each track will be played, in order.  
The track number currently being heard blinks in the display.  
Stopping to Listen to the Track Being Scanned:  
Press the 38 or SCN button again to stop the scan and keep  
on listening to a track normally.  
NOTE  
• The track scan function is cancelled when you stop playing a  
disc.  
• The track scan function only scans each track on a disc once.  
— 19 —  
CD/External disc control features  
Disc Scan  
(Function of disc changers)  
Magazine Random Play  
Play the tracks on all the discs in the disc changer in random  
order.  
(Function of disc changers)  
Successively play the beginning of each disc on a changer until  
you find the one that you want to listen to.  
1
Starting the disc scan:  
Press the M.RDM button to switch magazine random play on  
Press the D.SCN button. The D.SCN indicator lights up and the  
first 10 seconds of each disc will be played, in the order they  
are loaded on the changer.  
and off.  
The M.RDM indicator lights up when magazine random play is  
turned on.  
The disc and track numbers will change over and over in the  
display as the next track is being selected.  
When the disc/track has been selected, play will begin.  
The disc number currently being heard blinks in the display.  
Stopping to Listen to the Disc Being Scanned:  
Press the 38 or D.SCN button again to stop the scan and keep  
on listening to the disc normally.  
NOTE  
NOTE  
This function is not available with the following models:  
KDC-C200/C300/C400/C301/C401  
• The disc scan function is cancelled when you stop playing a  
disc.  
2
To change the track being heard, press the ¢ button.  
• The disc scan function only scans each disc on the changer  
Another disc/track will be selected and played.  
once.  
NOTE  
• "LOAD" is displayed when discs are being exchanged on the disc  
changer.  
• Magazine random play is canceled when you stop playing a disc.  
• The time needed for random selection depends on the number  
of discs loaded in the disc magazine.  
Random Play  
Play all the tracks on the current disc in random order.  
1
Press the RDM button to switch random play on and off.  
The RDM indicator lights up when random play is turned on.  
The track number will change over and over in the display as  
the next track is being selected.  
When the track has been selected, play will begin.  
NOTE  
(For disc changers)  
When all the tracks on a certain disc have been played using  
random play, the next disc on the changer will start playing using  
the same function.  
2
To change the track being heard, press the ¢ button.  
Another track will be selected and played.  
NOTE  
Random play is canceled when you stop playing a disc.  
— 20 —  
display after inserting a disc magazine, try playing it using the  
disc scan or a similar function to display the disc name. Also  
note that "No Access/No Disc" will be displayed when a disc has  
not been loaded.  
Text / Title Scroll  
This function permits the text to be scrolled and the entire text  
to be displayed. The scrolling method differs depending on the  
setting of scrolling in the function set system.  
Rapid display (forward / reverse):  
Press the DISC+ or DISCbutton.  
To scroll automatically:  
Pressing the DISC+ button will rapidly display the preset  
Press the DISP button to display the disc title or the track title.  
The display of the text will be scrolled repeatedly.  
names/disc titles in order.  
Pressing the DISCbutton will rapidly display the preset  
names/disc titles in reverse order.  
To scroll manually:  
1 Press the DISP button to display the disc title or the track title.  
2
When the name appears for the disc you want to play  
Press the SBF button.  
The disc whose name is displayed will be recalled, and the disc  
name preset play (DNPP) mode will end.  
2 Press the SCRL button.  
The display of the text will be scrolled once.  
NOTE  
Please see the function set system settings (page 33) about  
switching between manual scrolling and automatic scrolling.  
To cancel DNPP mode:  
Press the SBF button for at least one second.  
The disc name preset play (DNPP) mode will be canceled.  
Disc Name Preset Play (DNPP)(Function of disc changers)  
If you have preset the name of a disc that you want to listen to  
in the disc changer, you can look for it by name and start  
playing it.  
1
Press the SBF button for at least one second.  
"SBF DNPS/SBF Disc" will appear in the display, and the disc  
name preset play mode is entered.  
The preset names/disc titles of the disc in the disc changer to  
which you are currently listening are successively displayed for  
five seconds each.  
In any of the units that are connected, discs that have not been  
disc name preset will display "No Name".  
NOTE  
• You cannot use this function while doing track or disc repeat or  
track or disc scan or using random or magazine random play.  
• Discs in the disc changer that have never been played before  
will appear as "No Access" when the disc names are displayed.  
When you cannot identify a disc because of the "No Access"  
— 21 —  
CD/External disc control features  
NOTE  
Presetting Disc Names  
Store the names of discs to be displayed when played.  
Direct Alphabet Input  
(Function of remote)  
You can directly input letters using the number/letter entry  
buttons on the remote.  
Example: Use the following table to enter the name "DANCE".  
1
Play the disc whose name you want to preset.  
NOTE  
• This function is available only for the CD player of this unit and  
disc changers that feature the Disc Name Preset function.  
• This procedure is not to be used to store the disc and track titles  
for MDs that you record.  
Character  
Button to press  
# Times pressed  
#3  
#2  
#6  
#2  
#3  
1
1
2
3
2
“D”  
“A”  
“N”  
“C”  
“E”  
• This function cannot be available during the clock display and  
while using disc scan or magazine random play.  
2
Press the NAME button for at least two seconds.  
"Name Set" is displayed and the disc name preset mode is  
entered.  
The cursor blinks in the position where character input can be  
made.  
5
6
Continue steps 3 and 4 until all the characters are chosen for  
the name.  
3
4
Press either the 4 or ¢ button to move the cursor to the  
desired position.  
Press either the NAME button on the main unit or the OK  
button on the remote.  
The 4 button moves the cursor to the left, and the ¢  
The disc name is stored and the disc name preset mode is  
canceled.  
button to the right.  
You can also move the cursor left or right by pressing the  
TRACK+ or TRACK– buttons, respectively, on the remote  
control.  
If you make no entry in a 10-second period, the name will be  
stored with the characters input so far.  
NOTE  
Each time the 38 button is pressed, the characters to be  
entered change as listed below.  
• Up to 8 characters and 50 disc names can be registered in CD  
mode and external disc control mode.  
Press the DISC+ or DISCbutton to display the desired  
51st Disc Name Preset is made, the oldest disc name will be  
automatically erased to make room for the new setting.  
• Discs are identified by their total length and number of tracks. If  
another disc happens to have the same specifications as one  
that you have already stored a name for, the name will be  
displayed for it, too.  
character.  
Characters that can be displayed are as follows.  
Alphabet (upper case): _ A ~ Z  
Alphabet (lower case): _ a ~ z  
• If you want to change the name of a disc, repeat steps 1 and 2  
to display the name, and then repeat steps 3 and 4 to input the  
changes.  
Numerals and symbols: _ 0~9 / + - = & " ˚ ' < > [ ]  
• Disc names remain stored even if the reset button is pressed.  
• This function cannot be used when an MD is played with the  
MD changer "KMD-D401/KMD-D400/KMD-C30".  
— 22 —  
DSP features  
4 ¢  
FM  
DISP  
DSP/OFF  
#2 COMP  
#3 SFC  
AM  
POSI/  
R.SIZE  
#1  
Sound field control name  
DSP indicator  
— 23 —  
DSP features  
DSP (Digital Signal Processor)  
Nuance Level Adjustment  
You can adjust the level of the DSP sound effects.  
A DSP is a device which uses digital control to correct the audio  
signal and produce sound effects that can compensate for the  
small passenger compartment of a vehicle.  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
The DSP indicator lights up when the DSP is on.  
Turning the DSP On:  
2
Each time you press the FM or AM button, the DSP effects  
switch as follows;  
"Nuance High" j "Nuance Mid" j "Nuance Low"  
Press the DSP button.  
"DSP On" is displayed once and the DSP indicator lights up the  
DSP is turned on.  
NOTE  
Turning the DSP Control Mode on:  
Press the DSP button while the DSP indicator lights up.  
"DSP CTRL" is displayed and the DSP indicator starts blinking  
when the DSP control mode is entered.  
• This adjustment cannot be made when the Sound Field Control  
is set to "Bypass".  
• The default setting is "Mid".  
NOTE  
3
Press the DSP button to end the DSP control mode.  
• Be sure to turn the DSP control mode on when performing the  
operations described below in the DSP features.  
• If you make no button operation for 10 seconds, the DSP control  
mode is automatically canceled.  
Turning the DSP Off:  
DSP Bass Boost Control Level Adjustment  
This function can add the original bass sounds to the  
insufficient bass sounds from the rear during using the DSP  
effects for correction.  
Press the OFF button for at least one second.  
Sound Field Control  
This function reproduces many different virtual sound fields  
such as of a concert hall within a vehicle.  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
Switching the Sound Field Control:  
2
Each time you press the 4 or ¢ button, the width of  
frequency band for the bass boost switches as follows;  
"DBB STEP 1" (narrow band) j "DBB STEP 2" j "DBB STEP  
3" (wide band)  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
2
Each time you press the SFC button, the sound field control  
switches as follows;  
NOTE  
• This adjustment cannot be made when the Sound Field Control  
is set to "Bypass".  
• The default setting is "STEP 2".  
"Stadium" "Concert Hall" "Live House" "Theater" ➨  
"Disco" "Club Disco" "Jazz Club" "Studio" "Listening" ➨  
"Church" "Bypass" ➨  
3
Press the DSP button to end the DSP control mode.  
3
Press the DSP button to end the DSP control mode.  
— 24 —  
Compression Control Level Adjustment  
4
Press the DSP button to end the DSP control mode.  
This function can compress the dynamic range of music, so  
that low sounds which are covered over by road noise can be  
raised.  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
Room Size Setting  
This function can set the DSP effects for various room sizes.  
2
Each time you press the COMP button, the compression level  
switches as follows;  
"Comp Off" "Comp STEP 1" (Compression level is lower) ➨  
"Comp STEP 2" "Comp STEP 3" (Compression level is higher)  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
2
3
Press the R.SIZE button.  
NOTE  
The position currently set appears in the display.  
The default setting is "Off".  
3
Each time you press the 4 or ¢ button, the room size  
switches as follows;  
Press the DSP button to end the DSP control mode.  
"Room Large" (For large vans or RVs, etc.) j "Room  
Medium"(For sedans, etc.) j "Room Small" (For compact cars,  
etc.)  
NOTE  
• This adjustment cannot be made when the Position Setting is  
set to "ALL".  
Position Setting  
This function can set the DSP effects for various listening  
positions.  
• The default setting is "Medium".  
4
Press the DSP button to end the DSP control mode.  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
2
3
Press the POSI button.  
The position currently set appears in the display.  
Each time you press the POSI button, the position switches as  
follows;  
"ALL" "Front-Right" "Front-Left" "Front" "Rear" ➨  
NOTE  
• Be sure to set the balance and fader control to center position.  
If their settings are not set to center position, the Position  
Setting effect will not be obtained properly.  
• The default setting is "ALL".  
— 25 —  
DSP features  
Graphic Equalizer features  
DSP Setting Preset Memory  
Up to three sets of the DSP settings and conditions you  
adjusted can be stored in the memory, and then you can recall  
them with the single touch of a button.  
4 ¢  
FM  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
The DSP indicator blinks during the DSP control mode.  
2
3
Make the DSP settings and adjustments that you want to store  
in the memory.  
Press the button (#1-3) that you want to use for the DSP  
settings and adjustments for at least two seconds.  
"DSP MEM#" blinks once in the display to indicate that the data  
has stored.  
DISP  
4
Press the DSP button to end the DSP control mode.  
Recalling a DSP settings and adjustments you stored:  
1
Press the DSP button. "DSP CTRL" is displayed once the DSP  
control mode is entered.  
DISP  
EQ  
AM  
#1  
#3  
The DSP indicator blinks during the DSP control mode.  
#2  
KBS  
2
3
Press the preset button (#1-3) for the desired DSP settings and  
adjustments.  
Press the DSP button to end the DSP control mode.  
EQ indicator  
KBS name/Spectrum analyzer name/Equalizer frequency and level display  
— 26 —  
Graphic Equalizer features  
equalizer mode is entered.  
Graphic Equalizer  
This mode allows you to call up the preset equalizer curves,  
adjust the graphic equalizer, make the setting of the spectrum  
analyzer, and so on.  
The preset equalizer name currently set appears in the display.  
2
3
Each time you press the 4 or ¢ button, the selectable  
frequency band switches as follows;  
"60 Hz" j "120 Hz" j "250 Hz" j "500 Hz" j "1 kHz" j "2  
Turning the Graphic Equalizer Mode On:  
Press the EQ button.  
kHz" j "4 kHz" j "8 kHz" j "16 kHz"  
Press the FM or AM button.  
"EQ CTRL" is displayed once the Graphic equalizer mode is  
entered.  
Press the FM button to increase the equalizer level, and the  
AM button to decrease it.  
NOTE  
There are six levels for both plus and minus allowing each band  
to be set to one of 13 steps ("-12"~"+12").  
Be sure to turn the Graphic Equalizer mode on when performing  
the operations described below in the Graphic Equalizer features.  
4
Press the EQ button twice to end the Graphic equalizer mode.  
Turning the Graphic Equalizer Mode Off:  
Press the EQ button twice.  
Graphic Equalizer Preset Memory  
NOTE  
Up to three graphic equalizer curves can be stored in the  
memory, and then you can recall that equalizer curve with a  
single touch of a button.  
If you make no button operation for 10 seconds, the Graphic  
equalizer mode is automatically canceled.  
1
Press the EQ button. "EQ CTRL" is displayed once the Graphic  
equalizer mode is entered.  
Preset Equalizer (KBS - Kenwood Built-in Sound) Selection  
You can choose the equalizer from five settings whose sound  
qualities are preset to match music or vehicle characteristics.  
The preset equalizer name currently set appears in the display.  
2
3
Adjust the graphic equalizer curve that you want to store in the  
memory.  
Switching the Preset Equalizer:  
1
2
3
Press the EQ button. "EQ CTRL" is displayed once the Graphic  
Press the button (#1-3) that you want to use for the Graphic  
Equalizer curve for at least two seconds.  
"EQ MEM#" blinks once in the display to indicate that the data  
has stored.  
equalizer mode is entered.  
The preset equalizer name currently set appears in the display.  
Each time you press the KBS button, the preset equalizer  
switches as follows;  
"Rock" "Pops" "Dance" "Vocal" "Flat" ➨  
4
Press the EQ button twice to end the Graphic equalizer mode.  
Recalling a GraphicEqualizer curve you stored:  
1
Press the EQ button twice to end the Graphic equalizer mode.  
Press the EQ button. "EQ CTRL" is displayed once the Graphic  
equalizer mode is entered.  
The preset equalizer name currently set appears in the display.  
Graphic Equalizer Adjustment  
You can set the original equalizer curve which do not exist in  
the preset equalizer (KBS).  
2
3
Press the preset button (#1-3) for the desired Graphic Equalizer  
curve.  
Press the EQ button twice to end the Graphic equalizer mode.  
1
Press the EQ button. "EQ CTRL" is displayed once the Graphic  
— 27 —  
Graphic Equalizer features  
Spectrum Analyzer Display Selection  
You can select the display to enjoy sounds with eyes.  
Switching the Preset Spectrum Analyzer Display:  
1
Press the EQ button. "EQ CTRL" is displayed once the Graphic  
equalizer mode is entered.  
2
Press the DISP button.  
The spectrum analyzer name currently set appears in the  
display.  
3
4
Each time you press the DISP button, the spectrum analyzer  
display switches as follows;  
"SPEANA Scan" "Seascape" "Peak Hold" "Digital" ➨  
"Hopping" "Satellite" "Atlas" "Level Meter" "3D Graph"  
"EQ curve" ➨  
Press the EQ button twice to end the Graphic equalizer mode.  
— 28 —  
Function set system  
Function Set System  
4 ¢  
FM  
To accommodate a greater number of functions, a function set  
system has been employed for making settings. Press the FNC  
button to enter the function set mode and then display the  
function to make the setting.  
1
Select the mode that you want to make the setting of the  
function.  
2
Press the FNC button.  
"Function Set" is displayed when the function set mode is  
entered.  
The function that you can adjust is indicated with the current  
settings displayed.  
DISP  
3
Selecting function to set  
Press the ¢ button to search through the functions until you  
see the one you want to adjust in the display.  
Press the 4 button to search through the functions  
backward.  
Example: If you want to the setting of the touch sensor tone  
function from on to off, first search through the  
functions until you see "BEEP On" in the display.  
38  
SRC  
FNC  
#2  
#4  
#1  
AM  
#3  
4
5
Changing setting for currently displayed function  
Press either the AM or FM button.  
The setting will change for each function.  
Example: The setting of the touch sensor tone will switch from  
on to off, and "BEEP Off" is displayed.  
Ending the function set mode  
Press the FNC button.  
AUTO indicator  
Function mode and setting display  
— 29 —  
Function set system  
Function items in Standby mode:  
4. External Amp Control  
If this function is set to on, you can control the external  
1. Touch Sensor Tone  
This function produces a beep sound that accompanies button  
operation. It can be switched on or off.  
amplifier.  
Display and setting  
”Amp Cont On“  
”Amp Cont Off“  
Display and setting  
”BEEP On“  
NOTE  
”BEEP Off“  
When this function is set to on, the External Amp Control Setting  
function (function 9) in the section "Function items in Other  
mode:" is available to be controlled.  
2. Switching Preout  
Switch the preout between the rear and non-fading. When you  
switch to non-fading, you can adjust the volume separately.  
The factory default is rear preout.  
5. Opening Display  
If this function is set to on, the opening display appears when  
Display and setting  
the power is turned on.  
”Preout Rear“: Rear preout  
”Preout N-F“: Non-fading preout  
Display and setting:  
NOTE  
”Opening On“: Opening display function is on.  
”Opening Off“: Opening display function is off.  
• Be sure to turn the power of this unit off and on after you  
switch the preout.  
• When this function is set to "Preout N-F", functions 4, 5 and 8 in  
the section "Function items in Other mode:" are available.  
3. Digital Crossover Network  
If this function is set to on, you can adjust the setting of the  
Crossover network.  
Display and setting  
”D.X ‘over On“  
”D.X ‘over Off“  
NOTE  
When this function is set to on, functions from 1 to 8 in the  
section "Function items in Other mode:"(see p32) are available to  
be controlled.  
— 30 —  
6. Security Code  
When the battery is removed from the unit's power switch, you  
cannot turn on the unit again unless the preset security code is  
input. This function helps prevent theft.  
# Times  
pressed  
Step  
Button to press  
Display  
1
2
3
4
#1  
#2  
#3  
#4  
4
6
2
1
“3”  
“5”  
“1”  
“0”  
NOTE  
You must follow steps 1 to 9 to be able to use the Security Code  
function. Turning off the power during the procedure will  
deactivate the security code setting.  
Once the security code function has been activated, "CODE  
STBY" disappears from the function set system. Note that it will  
no longer be possible to cancel this function afterwards.  
7
Press the 38 button.  
The security code will be set.  
"CODE ✽✽✽✽1" appears in the display, asking you to enter the  
code once again for confirmation, and then you can start  
inputting the code.  
1
Select the four digits to use in your security code.  
NOTE  
8
9
Press the Preset button and input the security code again.  
The four-digit security code is very important, as you will need it  
to turn the unit on again when the code security function is on.  
Choose the number carefully and do not forget it (write it down  
and keep it separately in a safe place).  
Press the 38 button again.  
"CODE WRITE" will appear in the display, with the security code  
function turning on. From this point on, if the unit is  
disconnected from the battery, the security code must be  
entered the first time that the unit's power is turned on. "CODE  
✽✽✽✽" will appear in the display, asking you to input the code.  
2
Press the SRC button repeatedly and switch the display to "ALL  
OFF" to enter the standby mode.  
3
4
5
Press the FNC button.  
NOTE  
"Function Set" is displayed and the function set mode is turned  
on.  
If you input an incorrect security code, the display ask you once  
more to input the correct one. Follow the procedure in step 6  
above.  
Keep pressing the ¢ button until the “CODE STBY” appears  
in the display.  
Press the 4 button to search in the other direction.  
Press either the AM or FM button for at least two seconds.  
"CODE WRITE" will appear in the display for one second,  
indicating the code setting mode has been entered. When  
"CODE ✽✽✽✽" appears in the display, you can start inputting  
the code.  
If you press the RESET button or remove the battery:  
The first time you turn the unit on again, "CODE ✽✽✽✽" will  
appear in the display, asking you to input the security code.  
Repeat steps 8 and 9 above, and input the security code.  
You can start operating the unit again when "CODE OK!"  
appears in the display.  
If you enter the incorrect code, the power will turn off,  
displaying "CODE NG!". Enter the correct code to turn the unit  
on.  
6
Press the preset button and enter the security code that you  
have selected in step 1.  
Example: Use "3510" as the security code.  
— 31 —  
Function set system  
Function items in Other mode:  
6. Time Alignment for Front Output  
<In Tuner/CD/Cassette/External disc control mode>  
You can adjust the delay of sounds from front output.  
1. Frequency Setting of High Pass Filter for Front Output  
You can select the frequency to be cut of the high pass filter for  
front output.  
Display and setting  
“T-Alg F Off/0.5~18” (msec.)  
Display and setting  
“HPF-F Off/30/60/90/120/150/180/250” (Hz)  
7. Time Alignment for Rear Output  
You can adjust the delay of sounds from rear output.  
Display and setting  
2. Frequency Setting of High Pass Filter for Rear Output  
You can select the frequency to be cut of the high pass filter for  
rear output.  
“T-Alg R Off/0.5~18” (msec.)  
Display and setting  
8. Time Alignment for Non-fading Output  
You can adjust the delay of sounds from non-fading output.  
“HPF-R Off/30/60/90/120/150/180/250” (Hz)  
Display and setting  
3. Filter Slope Setting of High Pass Filter  
You can select the filter slope of the high pass filter.  
“T-Alg NF Off/0.5~18” (msec.)  
Display and setting  
“HPF Slope 12/18/24” (dB/Octave)  
9. External Amp Control Setting  
Adjust the bass boost level of the external amplifier using the  
main unit.  
4. Frequency Setting of Low Pass Filter for Non-fading Output  
You can select the frequency to be cut of the low pass filter for  
non-fading output.  
Display and setting  
"Amp Cont 1": Bass boost level is flat.  
"Amp Cont 2": Bass boost level is low. (+6 dB)  
"Amp Cont 3": Bass boost level is high. (+12 dB)  
Display and setting  
NOTE  
“LPF Off/150/120/100/80/60” (Hz)  
As of December 2001, the power amplifiers controllable by the  
main unit are as follows:  
KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T  
5. Filter Slope Setting of Low Pass Filter  
You can select the filter slope of the low pass filter.  
Display and setting  
“LPF Slope 12/18/24” (dB/Octave)  
— 32 —  
<In Tuner mode>  
<In CD/External disc control mode>  
10. Selecting Tuning Mode  
12. Text /Title Scroll  
Select which tuning mode — auto seek or manual — to use as  
This function permits the text to be scrolled and the entire text  
to be displayed. Switching between manual scrolling and  
automatic scrolling is permitted. The factory default is  
automatic scrolling.  
the default.  
When the AUTO indicator is on, auto seek tuning is selected.  
When the indicator is off, manual tuning is selected.  
Display and setting  
Display and setting  
"Auto Seek": auto seek mode  
"Manual Seek": manual tuning mode  
"AT. SCRL On": The text/title is scrolled repeatedly.  
"AT. SCRL Off": The text/title is scrolled once when the display  
is switched.  
NOTE  
11. Auto Memory Entry  
• Only units with a CD text feature and the MD supporting the  
title scroll permit title display.  
• This function can be set separately when the MD play and the  
CD play.  
You can automatically store all the receivable frequencies in  
the band currently being listened to, and then recall them with  
the touch of a button later. This function is especially useful  
when you are travelling and do not know what stations are  
available. Up to six frequencies can be stored this way.  
NOTE  
Select the band for auto memory entry before you enter the  
function set mode.  
Display and setting  
"AME Ready"  
Press either the AM button or FM button for at least two  
seconds to start auto memory function.  
The numbers of the preset station buttons showed in order.  
When all the stations in a certain band are stored in the preset  
memory, the auto memory entry stops. The tuner then plays  
the last station received.  
— 33 —  
Basic Operations of remote  
2CAUTION  
Do not set the remote on hot places such as above the  
dashboard.  
Loading and Replacing the Batteries:  
Use two “AAA”-size batteries.  
Slide the cover while pressing downwards to remove it as  
illustrated.  
Insert the batteries with the + and poles aligned properly,  
following the illustration inside the case.  
+
SRC  
+
SRC  
TUNE /4/TRACK –  
TUNE +/¢/TRACK +  
4
FM/DISC +  
¢
TUNE  
TRACK  
FM  
ATT  
+
DSIC  
38  
38  
AM  
AM/DISC –  
DNPP/SBF  
DNPP/  
SBF  
DIRECT  
OK  
2WARNING  
DIRECT/OK  
#0~9/A~Z  
ABC  
DEF  
Store unused batteries out of the reach of children. Contact a  
doctor immediately if the battery is accidentally swallowed.  
1
4
7
2
5
8
0
3
6
9
GHI  
JKL  
TUV  
QZ  
MNO  
WXY  
NOTE  
PRS  
• The provided batteries are intended for use in operation  
checking, and their service life may be short.  
• When the remote controllable distance becomes short, replace  
both of the batteries with new ones.  
REMOTE CONTROL UNIT  
NOTE  
A portion of the operations may not be possible, depending on  
the unit that is connected.  
Basic operations  
• VOLUME buttons  
— 34 —  
Press the + button to turn the volume up.  
Press the button to turn the volume down.  
Tuner features  
• Number/letter entry buttons  
• SRC button  
Press buttons #1-6 to recall preset stations.  
During direct access tuning, use these buttons to input the  
frequency of the station.  
Each time you press the SRC button, the mode switches as  
follows:  
Use to enter letters (alphabetical) during station name preset.  
Tuner mode  
4/¢ (TUNE) buttons  
Press the 4 button to decrease the frequency.  
Press the ¢ button to increase the frequency.  
Use to move the cursor left or right during station name preset.  
Tape mode  
CD mode  
• AM/FM button  
External disc control mode  
Press the AM button to select the AM band.  
Press the FM button to select and switch between FM1, FM2,  
and FM3 bands.  
Standby mode  
During station name preset, selects digits and symbols.  
NOTE  
• DIRECT/OK button  
• The mode switches to the next mode from any mode which  
cannot be used.  
Selects the direct access tuning mode, used to input frequencies  
directly. Press this button again to cancel the mode while it is  
operating.  
• The external disc control mode will differ depending on the unit  
that is connected.  
During station name preset, stores the already input data in  
memory and ends the input mode.  
During Station name preset play mode, selects station.  
• ATT button  
Turns down the volume quickly. To return the volume to its  
original level, press the button again. Turning the volume all the  
way down also cancels attenuation.  
• DNPP/SBF button  
Enters and cancels the Station Name Preset Play mode.  
button  
38 button  
Each time you press this button, the panel slides one step at a  
time.  
Selects the type of characters at the time of entering the station  
name.  
When the panel has been slid down completely, press this  
button to close the panel.  
— 35 —  
Basic Operations of remote  
Press the same button again to start play again.  
Selects the type of characters at the time of entering the disc  
name.  
Cassette player features  
4/¢ buttons  
Press the 4 button to start play again at the beginning of the  
current track.  
• OK button  
During disc name preset, stores the already input data in  
memory and ends the input mode.  
Press the ¢ button to start play at the beginning of the next  
track.  
Selects disc during the disc name preset play mode.  
Press either the 4 or ¢ button to skip backward or forward  
to other tracks after entering the number of tracks used in DPSS.  
• DNPP/SBF button (for disc changers)  
Enters and cancels the Disc Name Preset Play mode.  
• AM button  
Rewinds the tape.  
• FM button  
Fast forwards the tape.  
38 button  
Plays the reverse side of the tape. When pressed during fast  
forward and rewind, this button stops the tape and starts playing  
it.  
• Number/letter entry buttons  
Use to enter the number of tracks you want to skip used in  
DPSS.  
CD/External disc control features  
• Number/letter entry buttons  
Used to specify the track (disc) number used in direct track (disc)  
searches.  
Use to enter letters during disc name preset.  
4/¢ buttons  
Press the 4 button to search through the tracks backward.  
Press the ¢ button to search through the tracks forward.  
Use to move the cursor while entering disc name.  
• DISC buttons (for disc changers)  
Press the DISCbutton to search through the discs backward.  
Press the DISC+ button to search through the discs forward.  
Select numbers and symbols while entering disc name.  
38 button  
When a disc is playing, this button pauses the play.  
— 36 —  
Accessories  
Installation Procedure  
1. To prevent a short circuit, remove the key from the ignition and  
External view  
disconnect the - battery.  
......... Number of items  
2. Make the proper input and output wire connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
4. Connect the wiring harness wires in the following order: ground,  
battery, ignition.  
5. Connect the wiring harness connector to the unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
(M5×6mm)  
1
2
3
4
5
.........6  
(DPX-6020 only)  
(M4×8mm)  
.........1  
8. Press the reset button.  
.........1  
2CAUTION  
• If your car's ignition does not have an ACC position, connect  
the ignition wires to a power source that can be turned on and  
off with the ignition key. If you connect the ignition wire to a  
power source with a constant voltage supply, as with battery  
wires, the battery may die.  
• If the console has a lid, make sure to install the unit so that the  
faceplate will not hit the lid when closing and opening.  
• If the fuse blows, first make sure the wires aren’t touching to  
cause a short circuit, then replace the old fuse with one with  
the same rating.  
(M5×7mm)  
.........6  
.........1  
• Do not let unconnected wires or terminals touch metal on the  
car or anything else conducting electricity. To prevent a short  
circuit, do not remove the caps on the ends of the unconnected  
wires or the terminals.  
• Connect the speaker wires correctly to the terminals to which  
they correspond. The unit may be damaged or fail to work if you  
share the - wires or ground them to any metal part in the car.  
• After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
• Insulate unconnected wires with vinyl tape or other similar  
material.  
2CAUTION  
The use of any accessories except for those provided might result  
in damage to the unit. Make sure only to use the accessories  
shipped with the unit, as shown above.  
• Some disc changers need conversion cords for connection. See  
the section on "Safety Precautions" for details.  
• Mount the unit so that the mounting angle is 30° or less.  
— 37 —  
Connecting Wires to Terminals  
Front left output (White)  
Front right output (Red)  
Rear left output (White)/  
Non-fading left output (White)  
FM/AM antenna input  
KENWOOD disc changer control input  
0  
NOTE  
Fuse  
(10A)  
To connect the Disc changer,  
consult your Disc changer manual.  
Rear right output (Red)/  
Non-fading right output (Red)  
Wiring harness  
(Accessory5)  
White/Black  
When using the optional power  
amplifier, connect to its power  
control terminal.  
To front left  
speaker  
P.CONT  
FRONT•L  
White+  
Power control wire  
(Blue/White)  
Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for  
the booster amplifier of the film-type antenna.  
Gray/Black  
To front right  
speaker  
ANT  
CONT  
Motor antenna control wire  
(Blue)  
FRONT•R  
+
Gray  
To "EXT.AMP.CONT." terminal of the amplifier  
having the external amp control function.  
Green/Black  
EXT.  
CONT.  
To rear left  
speaker  
External amplifier control wire  
(Pink / Black)  
REAR•L Green+  
Purple/Black  
To car light control switch  
ILLUMI  
Automatic illumination/Dimmer  
control wire (Orange)  
Ignition key  
switch  
To rear right  
speaker  
REAR•R  
+
Purple  
Ignition wire (Red)  
ACC  
Car fuse  
box  
(Main  
fuse)  
Battery wire (Yellow)  
Car fuse box  
Ground wire (Black) - (To car chassis)  
Battery  
+
2CAUTION  
When only two speakers are being connected to the system,  
connect the connectors either to both the front output  
terminals or to both the rear output terminals (do not mix  
front and rear). For example, if you connect the + connector  
of the left speaker to a front output terminal, do not connect  
the - connector to a rear output terminal.  
2WARNING  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
— 38 —  
Installation (for TOYOTA, NISSAN Car etc.)  
2CAUTION  
When performing a check of the CD operation prior to installation,  
place this unit in a hirizontal position and perform a loading/eject of  
the CD.  
Installation  
Install onto the car bracket using the supplied screws (M5 × 6 mm,  
M5 x 7 mm). The holes of the car bracket to use will differ  
depending on the car model.  
DPX-6020: Accessory2  
DPX-6030: Commercially available  
(M4 × 8 mm)  
When a ground wire is  
included in the wiring kit  
(which is sold separately),  
fasten the ground wire  
with the binding screw  
located on the rear panel  
of this unit.  
Accessory1  
(M5 × 6 mm)  
or Accessory4  
(M5 × 7 mm)  
Accessory3  
(Only for NISSAN car)  
— 39 —  
Troubleshooting Guide  
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before  
calling service, first check the following table for possible problems.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The power does not turn on.  
The fuse has blown.  
After checking for short circuits in the wires, replace the  
fuse with one with the same rating.  
No sound can be heard, or the  
volume is low.  
Attenuator is turned on.  
Turn off Attenuator.  
The fader or balance settings are set all the way to one  
side.  
Reset the fader or balance settings (see p. 7).  
The input/output wires or wiring harness are connected  
incorrectly.  
Reconnect the input/output wires or the wiring harness  
correctly. See the section on "Connecting Wires to  
Terminals".  
The cassette tape is bad.  
Try playing another cassette tape. If works fine, the first  
tape was bad.  
The tape does not go in. /  
No sound can be heard even  
though the tape display is  
made.  
The car ignition was turned off during tape eject; or the  
tape was pulled out during loading, switching the mode to  
tape mode even though no tape is in.  
Press the Eject button.  
Nothing happens when the  
buttons are pressed.  
The computer chip in the unit is not functioning normally.  
The tape head is dirty.  
Press the reset button on the unit (see p. 4).  
Clean the tape head, referring to the section on "Cleaning  
the tape head" (see p. 4).  
The sound quality is poor or  
distorted.  
One of the speaker wires is being pinched by a screw in  
the car.  
Check the speaker wiring.  
The speakers are not wired correctly.  
Reconnect the speaker wires so that each output terminal is  
connected to a different speaker.  
Radio reception is poor.  
The car antenna is not extended.  
Pull the antenna out all the way.  
The antenna control wire is not connected.  
Connect the wire correctly, referring to the section on  
"Connecting Wires to Terminals".  
— 40 —  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The memory is erased when  
the ignition is turned off.  
The battery wire has not been connected to the proper  
terminal.  
Connect the wire correctly, referring to the section on  
"Connecting Wires to Terminals".  
The ignition and battery wire are incorrectly connected.  
Connect the wire correctly, referring to the section on  
"Connecting Wires to Terminals".  
A CD ejects as soon as it is  
loaded.  
The CD is upside-down.  
The CD is quite dirty.  
Load the CD with the labeled side up.  
Clean the CD, referring to the section on "Cleaning CDs" (see  
p. 5).  
The sound skips on a CD.  
A track will not play.  
The CD is scratched or dirty.  
Clean the CD, referring to the section on "Cleaning CDs" (see  
p. 5).  
Random play has been selected.  
Turn off random play (see p. 20).  
The DSP effects are  
imperceptible.  
You are using a two-speaker system.  
Use a front/rear four-speaker system.  
The front and rear output are reversed.  
Connect the wire correctly, referring to the section on  
"Connecting Wires to Terminals".  
Connect the wire correctly, referring to the section on  
"Connecting Wires to Terminals".  
The + and - of speakers are reversed.  
The fader or balance settings are set all the way to one  
side.  
Reset the fader or balance settings (see p. 7).  
— 41 —  
Troubleshooting Guide  
External Disc Control Mode  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The disc control mode cannot  
be selected.  
No wire has been connected to the disc changer input  
terminal on the unit.  
Connect the wire to the disc changer input terminal on the  
unit.  
The specified disc does not  
play, but another one plays  
instead.  
The specified CD is quite dirty.  
Clean the CD.  
The CD is upside-down.  
Load the CD with the labeled side up.  
The disc is loaded in a different slot from that specified.  
Eject the disc magazine and check the number for the  
specified disc.  
The disc is severely scratched.  
Something is touching the disc changer.  
The CD is scratched or dirty.  
Try another disc instead.  
The sound skips.  
Remove whatever is touching it.  
If skipping happens at the same place when the car is  
stopped, something with the CD is wrong. Clean the CD.  
The computer chip in the unit is not functioning normally.  
Random play or magazine random play has been selected.  
Press the reset button on the unit (see p. 4).  
The display shows that the  
changer is being played, but no  
sound can be heard.  
The specified track will not  
play.  
Turn off random play or magazine random play (see p. 20).  
If the following situations, consult your nearest service center:  
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX Mode" showing in the display during the Changer  
Mode.  
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, "AUX  
Mode" is displayed when switching modes.  
The following messages are displayed when certain problems are occurring in your system. Take the recommended  
actions.  
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.  
EJECT  
]
Load the disc magazine properly.  
No disc has been loaded in the disc magazine.  
No Disc  
]
Load a disc into the disc magazine.  
— 42 —  
No disc has been loaded in the disc magazine.  
Error 04  
]
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.  
]
Clean the CD and load it correctly.  
Nothing has been recorded on the MD.  
Blank Disc  
No Track  
No tracks are recorded on the MD, although it has a title.  
The unit is malfunctioning for some reason.  
Error 77  
]
Press the reset button on the unit. If the "Error 77" code does not disappear, consult your nearest service center.  
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.  
Mecha Error  
]
Press the eject button on the unit. And then, press the reset button on the unit.  
If the "Mecha Error" code does not disappear, consult your nearest service center.  
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping  
all operation.  
H-Hold  
]
Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the  
disc will start playing again.  
An attempt was made to display the track/disc title of the MD disc during play, but the MD has no titles.  
No Title  
• An attempt was made to display the name of the station being received but it was not set in memory.  
• An attempt was made to display the name of the disc being played but it was not set in memory.  
• An attempt was made to display the station name/disc name after the battery had been removed for a long period.  
No Name  
An attempt was made to display the track/disc title of the CD during play, but the CD has no texts.  
No Text  
Error 12  
The MD you tried playing is designed for use with data.  
]
Eject the MD designed for data and load the one designed for music.  
The tape player is malfunctioning.  
]
Eject the tape and try inserting it again.  
Contact the Kenwood dealer if this indicator continues blinking or the tape cannot be ejected.  
The CD player is malfunctioning.  
]
Eject the CD and try inserting it again.  
Contact the Kenwood dealer if this indicator continues blinking or the CD cannot be ejected.  
— 43 —  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
CD player section  
Frequency range  
Laser diode ....................................................GaAlAs (λ=780 nm)  
Digital filter (D/A)......................................8 Times Over Sampling  
D/A Converter ......................................................................1 Bit  
Spindle speed ..............................................500 – 200 rpm (CLV)  
Wow & Flutter........................................Below Measurable Limit  
Frequency response ( 1 dB) ................................10 Hz – 20 kHz  
Total harmonic distortion (1 kHz) ......................................0.01 %  
Signal to Noise ratio ................................................93 dB (1 kHz)  
Dynamic range ....................................................................93 dB  
Channel separation..............................................................85 dB  
(50 kHz space) ................................87.5 MHz – 108.0 MHz  
(200 kHz space) ..............................87.9 MHz – 107.9 MHz  
Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 )  
Quieting Sensitivity (S/N = 50dB)................15.2dBf (1.6 µV/75 )  
Frequency response ( 3.0 dB) ..............................30 Hz – 15 kHz  
Signal to Noise ratio (MONO) ..............................................70 dB  
Selectivity ( 400 kHz) ......................................................80 dB  
Stereo separation (1 kHz) ....................................................40 dB  
AM tuner section  
Frequency range  
(9 kHz space) ......................................531 kHz – 1611 kHz  
(10 kHz space) ....................................530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB) ............................28 dBµ (25 µV)  
Audio section  
Maximum output power ..................................................47 W × 4  
Full bandwidth power (at less than 1% THD)..................22 W × 4  
Preout level / Load................................................1500 mV/10 kΩ  
Preout impedance ............................................................600 Ω  
Cassette player section  
Tape speed ..............................................................4.76 cm/sec.  
Wow & Flutter (WRMS) ....................................................0.08 %  
Frequency response (70 µs)......................25 Hz – 22 kHz ( 3 dB)  
Separation (1 kHz) ..............................................................40 dB  
Signal to Noise ratio  
DSP/EQ section  
A/D Converter  
..3-dimensional 20-bit ∆ Σ system 128-times oversampling  
D/A Converter  
..3-dimensional 20-bit ∆ Σ system 128-times oversampling  
EQ frequency..................................60 Hz/120 Hz/250 Hz/500 Hz/  
..........................................1 kHz/2 kHz/4 kHz/8 kHz/16 kHz  
Adjustable range .............................................................. 12 dB  
(Dolby NR OFF)..........................................................60 dB  
(Dolby B NR ON)........................................................68 dB  
General  
Operating voltage..............................14.4 V (11 – 16 V allowable)  
Current consumption....................................10 A at Rated power  
Installation size (W × H × D) ........................178 × 100 × 155 mm  
7 × 3-15/16 × 6-1/8 in.  
Weight ................................................................................3.1 kg  
— 44 —  

Rockford Fosgate 4600X User Manual
RCA EZ4000BLR User Manual
Radio Shack 1500 User Manual
Plantronics 50 0230B 002 User Manual
Pioneer DVH 3150UB User Manual
Panasonic PV VM202 User Manual
Panasonic CQ C500U User Manual
Nikon AF S DX NIKKOR 85mmf35G User Manual
KitchenAid Blender KHB2351 User Manual
Kenwood KDS P900 User Manual