KDC-3051R
KDC-3051G
KDC-3051RY
KDC-3051GY
KDC-315A
KDC-315R
KDC-3251RY
CIND-SRETCERIVUERCTION MANUAL
AMMOPLID-TUENEDR ’LEECMTEUPRLDOE CID
РИAHДИCОПTРPИЕУMKНИЦКИС KЯOMППOAKTЭ–ДKИCСKПAЛMИУATAЦИИ
АІНВТСОМТАРГНУІТКОЦЛАІЯ З ЕКСПЛУАТАЦІЇ
This symbol mark indicates that Kenwood manufactured this product so as to decrease
harmful influence on the environment.
Изделие изготовлено в Mалайзии
Autogood products Internet store “130”
© 2010 Kenwood Corporation All Rights Reserved.
GET0671-001A (EW/E2W)
Safety
CONTENTS
Safety
WARNING
2
4
Stop the car before operating the unit.
Preparation
Important to know...
How to attach/detach the faceplate
How to reset your unit
Initial settings before operations
To prevent a short circuit, never put or
leave any metallic objects (such as coins or
metal tools) inside the unit.
Caution: Adjust the volume so that you
can hear sounds outside the car. Driving
with the volume too high may cause an
accident.
Condensation: When the car is air-
conditioned, moisture may collect on the
laser lens. This may cause disc read errors.
In this case, remothe disc and wait for
the moisture to aporate.
Basic operations
Getting started
5
6
Canceling the display demonstration
Setting the demonstration mode
Adjusting the clock
Listening to the radio
6
8
Adjust [SETTINGS] mode settings
This unit can only play the CDs with:
Listening to a disc
Selecting Repeat Play
Selecting Random Play
Selecting Scan Play
The illustrations in this manual are
examples used to explain more clearly
how the controls are used. Therefore, what
appears on the illustrations may differ from
what appears on the actual equipment.
If you experience problems during
installation, consult your Kenwood dealer.
When you purchase external components,
check with your Kenwood dealer to make
sure that they work with your model and in
your area.
Selecting a folder/track/file
Listening to the other external
components
9
Function settings
10
11
12
Troubleshooting
Installation/connection
Detailed information and notes about the
playable audio files are stated in an online
manual on the following site:
Basic procedure
Warning
Caution
Wiring connection
Installing the unit
Specifications
15
2
Autogood products Internet store “130”
The marking of products using lasers
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It means
that the unit is utilizing laser beams that
are of a weaker class. There is no danger of
hazardous radiation outside the unit.
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo,
192-8525 Japan
EU Representative’s:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN,
The Netherlands
For Turkey
Bu ürün 26891sayılı Resmi Gazete’de
yayımlanan Elektrikli ve Elektronik Eşyalarda
Bazı Zararlı Maddelerin Kullanımının
Sınırlandırılmasına DaYönetmeliğe uygun
olarak üretilmiştir.
This Product is not installed by the
manufacturer of a vehicle on the production
line, nor by the professional importer of a
vehicle into an EU Member State.
This product complies with Directive,
Number 26891 regarding“REGULATION ON
THE RESTRICTION OF THE USE OF CERTAIN
HAZARDOUS SUBSTANCES IN LECTRICAL
D ELECTRONIC EQUIPMENT”.
Information on Disposal of Old Electrical
and Electronic Equipment and Batteries
(applicable for EU countries that have
adopted separate waste collection
systems)
Products and batteries with the
symbol (crossed-out wheeled bin)
cannot be disposed as hold
waste.
Old electrical and electronic
equipment and batteries should
be recycled at a facility capable
of handling these items and their
waste byproducts.
Muting upon the reception of a
phone call
To use this feature, connect the MUTE lead
to your telephone using a commercial
telephone accessory. (page 13, 14)
When a call comes in, “CALL”appears.
The audio system pauses.
Contact your local authority
for details in locating a recycle
facility nearest to you. Proper
recycling and waste disposal will
help conserve resources whilst
preventing detrimental effects on
our health and the environment.
Notice: The sign“Pb”below the
symbol for batteries
To continue listen to the audio system
during a call, press SRC. “CALL”
disappear and the audio system resumes.
When a call ends, “CALL”disappear.
The audio system resumes.
indicates that this battery
contains lead.
Autogood products Internet store “130”
3
Preparation
How to attach/detach the faceplate
The faceplate is a precision piece of
equipment and can be damaged by shocks
or jolts.
To prevent deterioration, do not touch the
terminals of the unit and faceplate with
your fingers.
1
1
2
2
How to reset your unit
If this unit fails to operate properly, press the
reset button.
Do not expose the faceplate to direct
sunlight, excessive heat, or humidity. Also
avoid places with too much dust or the
possibility of water splashing.
Keep the faceplate in its casing while
detached.
The unit returns to
factory settings when the
reset button is pressed.
Reset button
Initial settings before operations
1
2
3
4
Press SRC to enter [STANDBY] mode.
Press the volume knob to enter [FUNCTION] mode.
Turn the volume knob to select [INITIAL then press to enter.
Turn the volume knob to make a selection, then press to confirm.
See table below for selection.
5
Hold
to finish the proced
Item
electable setting (Preset: *)
PRESET TYPE NORM*: Memorizes one staon for each preset button in each band (FM1/ FM2/ FM3/ MW/ LW). ;
MIX: Memorizs one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ MW/ LW).
KEY BEEP
ON*/ OFF: Activates/deactivates the keypress tone.
RUSSIAN SET ON: Folder name, file name, song title, artist name, album name are displayed in Russian (if applicable). ;
OFF*: Cancels.
P-OFF WAIT Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.
––––: Cancels ; 20M*: 20 minutes ; 40M: 40 minutes ; 60M: 60 minutes
BUILTIN AUX ON1*: Outputs sound of the connected external component when “AUX” is selected as the source. ;
ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When you
turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn
the volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.
CD READ
1*: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to play as a music CD.
SWITCH PRE REAR*/ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the
rear of the unit (through an external amplifier).
SP SELECT
OFF*/ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.
[SWITCH PRE] is selectable only with KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R/ KDC-3251RY.
4
Autogood products Internet store “130”
Basic operations
Loading slot
Ejects the disc
Detaches the faceplate
Display window
Volume knob
Auxiliary input jack
The following indicator lights up when...
ST: A stereo broadcast is received (FM).
IN: A disc is in the unit.
TI: Traffic Information ction is turned on.
RDS: RDS service is available.
When you press or hold the following button(s)...
Button
General operation
Turns on.
Turns off if pressed and held.
Selects the available sources (TUNER, CD, AUX, STANDBY), if the power is
turned on.
SRC
• If the source is realayback also starts. “CD” is selectable only when a disc is
loaded.
Volume knob
(turn)
Adjusts the volume level.
Selects items.
Volume knob
(press)
Confirms selection.
Enters [FUNCTION] settings.
Selects the FM bands (FM1/ FM2/ FM3) or MW/ LW.
Selects the next folder.
BAND
Pauses/resumes playback of a disc.
Mutes the sound while listening to a radio or an external component
connected to the auxiliary input jack.
Searches for a radio station.
4
/
¢
Selects track/file.
Fast-forwards/reverses tracks if pressed and held.
Changes the display information.
Scrolls the display information if pressed and held.
Enters clock adjustment mode directly (page 6) if pressed and held while in
clock display screen.
SCRL DISP
Returns to the previous item.
Exit from setting mode if pressed and held.
Autogood products Internet store “130”
5
Getting started
3
4
Turn the volume knob to select [ON] or
[OFF].
If [ON] is selected, display demonstration
starts if no operation is done for about
20 seconds.
Canceling the display
demonstration
The display demonstration is always turned
on unless you cancel it.
When you turn on the power (or after you
reset the unit), the display shows:
[CANCEL DEMO] \ [PRESS] \
[VOLUME KNOB]
Hold
to finish the procedure.
Adjusting the clock
1
2
3
4
Press the volume knob to enter
[FUNCTION] mode.
Turn the volume knob to select
[SETTINGS], then press to enter.
Turn the volume knob to select [CLOCK],
then press to enter.
Turn the volumnob to select
[CLOCK ADJ], then press to enter.
Clock hour flashes on the display.
Turn the volume knob to adjust the
hour, then press to enter minute
adjustment.
Clock minutes flashes on the display.
Turn the volume knob to adjust the
minute, then press to confirm.
1
Press the volume knob.
[YES] is selected as the initial setup.
Press the volume knob again to confirm.
[DEMO OFF] appears.
2
If no operation is done for about
15 seconds or if you turn the volume knob
to select [NO] in step 2, [DEMO MODE]
appears and the display demonstration
starts.
5
6
7
Setting the demonstration mode
1
Press the volume knob to enter
[FUNCTION].
2
Turn the volume knob to select
[DEMO MODE], then press tter.
Press 4
hour and minute adjustment.
Hold to finish the procedure.
/
¢ to move between the
Listening to the radio
Hold to turn on or off the Traffic Information function (not applicable if“MW/ LW”is selected).
Hold for about 2 seconds to memorize the current station or the selected Program
Type. (Refer to [PTY SEARCH] on page 7 to select the Program Type.)
Press briefly to recall memorized station (or Program Type after entering the PTY
search mode).
6
Autogood products Internet store “130”
1
2
3
Press SRC to select “TUNER.”
Press BAND repeatedly to select a band (FM1/ FM2/ FM3/ MW/ LW).
Press 4 ¢ to search for a station.
/
Adjust [SETTINGS] mode settings
While listening to the radio...
1
2
3
Press the volume knob to enter [FUNCTION] mode.
Turn the volume knob to select [SETTINGS], then press to enter.
Turn the volume knob to make a selection, then press to confirm.
See table below for selection.
4
Hold
to finish the procedure.
Item
LOCAL SEEK
SEEK MODE
Selectable setting (Preset: *)
ON: Searches only FM stations with good reception. ; OFF*: Cancels.
Selects the tuning mode for buttons.
4
/
¢
AUTO1*: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset
memory. ; MANUAL: Manually search for a station.
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ; NOCancels (automatic
memorizing is not activated). (Selectable only if [NORM] is selected for [PRESET TYPE].) (page 4)
MONO SET
ON: Improves the FM reception (but the stereo effect may be lost). ; OFF*: Cancels (stereo effect resumes).
Selects the available Program Type (see table below). Then, press to start searching.
Press the volume knob to enter PTY language selection. Turn the volume knob to select the PTY language
PTY SEARCH
4
/
¢
(ENGLISH*/ FRENCH/ GERMAN), then presnfirm.
NEWS SET
AF SET
0M – 90M: Sets the time for receiving the next news bulletin. ; OFF*: Cancels.
ON*: Automatically searches for another station broadcasting the same program in the same RDS network
with better reception wheurrent reception is poor. ; OFF: Cancels.
RDS REG
ATP SEEK
ON*: Switches to another stnly in the specific region using the “AF” control. ; OFF: Cancels.
ON*: Automatically searchefor a station with better reception when the traffic information's reception is
poor. ; OFF: Cncels.
[PTY SEARCH] is selectable only when the source is “FM.”
[NEWS SET/ AF SET/ RDS REG/ ATP SEEK] is selectable only when the source is “FM.” If other playback source is selected,
these settings are selectable under [RDS SET] item. (page 11)
Available Program Type:
SPEECH
DRAMA
MUSIC
CULTURE
LIGHT M (music) CLASSICS
NEWS
AFFAIRS
VARIED
INFO
SPORT
EDUCATE
SCIENCE
POP M (music) ROCK M (music) EASY M (music)
OTHER M (music) WEATHER
TRAVEL
FINANCE
JAZZ
CHILDREN
COUNTRY
SOCIAL
NATION M (music)
RELIGION
OLDIES
PHONE IN
FOLK M (music) DOCUMENT
LEISURE
The unit will search for the Program type categorized under [SPEECH] or [MUSIC] if selected.
[SPEECH] : White character item. ; [MUSIC] : Black character item.
The RDS feature won't work where the service is not supported by any broadcasting station.
If the volume is adjusted during reception of traffic information, the adjusted volume is
memorized automatically. It will be applied the next time Traffic Information function is
turned on.
Autogood products Internet store “130”
7
Listening to a disc
Ejects the disc. (“NO DISC”appears and“IN”indicator goes off.)
Press to select track/file.
Hold to fast-forwards/reverses.
Press to select folder.
1
2
Press SRC to turn on the power.
Insert a disc into the loading slot.
Playback starts automatically.
3
Press
to resume/pause playback (if necessary).
Selecting Repeat Play
Selecting Scan Play
Press number button 4 (REP) repeatedly
Press number button 2 (SCAN)
to make a selection.
repeatedly to make a selection.
Audio CD : TRAC (track) REPEAT,
REPEAT OFF
MP3/WMA : FILE REPEAT, FOLD )
REPEAT, REPEAT OFF
Audio CD : TRAC (track) SCAN, SCAN OFF
MP3/WMA : FILE SCAN, SCAN OFF
If scan play is selected, the unit starts
playing the first 10-second intro of the
music in the disc or the current folder. If
“SCAN OFF”is selected, the unit resumes
normal play of the current song.
Selecting Random Play
Press number button 3 (ALL RDM)
repeatedly to make a selection.
Selecting a folder/track/file
Audio CD : DISC RANDOM, RANDOM OFF
MP3/WMA : FOLD (folder) RANDOM,
ALL RANDOM, RANDOM OFF
Press and hold number button
3 (ALL RDM) to select“ALL RANDOM”only
if“RANDOM OFF”is selected initially.
1
Press
to enter Music Search mode.
“SEARCH” appears, then the current file
name appears on the display.
2
Turn the volume knob to select a folder/
track/file, then press to confirm.
To return to the root folder (or first track for
audio CD), press BAND.
To return to the previous folder, press
.
To cancel the Music Search mode, press
and hold
.
< or > on the display indicates that
preceded/next folder is available.
8
Autogood products Internet store “130”
Discs that cannot be used
Discs that are not round.
Discs with coloring on the recording surface or discs that are dirty.
You cannot play a Recordable/ReWritable disc that has not been finalized. (For the
finalization process refer to your disc writing software, and your disc recorder instruction
manual.)
3-inch CD cannot be used. Attempt to insert using an adapter can cause malfunction.
Listening to the other external
components
Preparation : Make sure [ON1] or [ON2] is selected for [BUILTIN AUX]. (page 4)
Auxiliary input jack
3.5 mm stereo mini plug
optional accessory)
1
2
3
Press SRC to select “AUX.”
Turn on the external component and start playing.
Turn the volume knob to adjust the volume.
Portable audio device
(optional accessory)
Maintenance
Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or soft cloth. Failure to
observe this precaution may result in damage to the monitor or unit.
Cleaning the connector: Wipe off dirt on the connector of the unit and faceplate. Use a
cotton swab or cloth.
Handling discs
Do not touch the recording surface of the disc.
Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
Do not use any accessories for the disc.
Clean from the center of the disc and move outward.
Clean the disc with a dry silicon or soft cloth. Do not use any solvents.
When removing discs from this unit, pull them out horizontally.
Remove the rims from the center hole and disc edge before inserting a disc.
Autogood products Internet store “130”
9
Function settings
1
2
3
Press the volume knob to enter [FUNCTION] mode.
Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter.
Turn the volume knob to make a selection, then press to confirm.
See table below for selection.
Repeat step 3 until the desired item is selected/activated.
Press
to return to the previous item.
4
Hold
to finish the procedure.
[AUDIO CTRL] : While listening to any source except in STANDBY state...
Item Selectable setting (Preset: *)
SUB-W LEVEL –15 — +15 (Preset: 0): Adjusts the subwoofer output level.
BASS BOOST B.BOOST LV1*/ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.
SYSTEM Q
NATURAL*/ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the
music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS ADJUST BASS C FRQ: 60/ 80/ 100*/ 200: Selects the center frequency.
BASS LEVEL: –8 — +8 (Preset: 0): Adjusts the level.
BASS Q FCTR: 1.00*/ 1.25/ 1.50/ 2.00: Adjusts the Q factor.
BASS EXTEND: ON: Turns on the extended bass. ; OFF*: Cancels.
MID ADJUST MID C FRQ: 0.5K/ 1.0K*/ 1.5K/ 2.5K: Selectthe center frequency.
MID LEVEL: –8 — +8 (Preset: 0): Adhe level.
MID Q FCTR: 0.75/ 1.00*/ 1.25: Adjusts thQ factor.
TRE ADJUST TRE C FRQ:
TRE LEVEL:
10.0K/ 12.5K*/ 15.0K/ 17.5K: Selects the center frequency.
–8 — eset: 0): Adjusts the level.
BALANCE
FADER
L15 — R15 (Preset: 0): Adhe left and right speaker output balance.
R15 — F15 (Preset: 0): Ajusts the rear and front speaker output balance.
ON*: Turns on the subwoofer output. ; OFF: Cancels.
SUB-W SET
DETAIL SET
LPF SUB-W: THROUGH*: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies
higher than 85 Hz/ 120 Hz/ 160 Hz are cut off.
SUB-W PHASE: REV (180°)/ NORM (0°)*: Selects the phase angle of the subwoofer output to be in line
with the speaker output for optimum performance. (Selectable only if a setting other than
[THROUGH] is selected for [LPF SUB-W].)
SUPREME SET: ON*: Creates realistic sound by interpolating the high-frequency components that are lost
in MP3/WMA audio compression. ; OFF: Cancels. (Selectable only when playback an MP3/
WMA disc.)
VOL OFFSET: –8 — +8 (for AUX) ; –8 — 0 (for other sources): Presets the volume adjustment level of
(Preset: 0)
each source. The volume level will automatically increase or decrease when you change the
source. (Before making an adjustment, select the source you want to adjust.)
KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R/ KDC-3251RY only:
[SUB-W LEVEL/ SUB-W SET/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 4)
[SUB-W LEVEL/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON].
Select a source before making a source tone memory adjustment, [BASS ADJUST/ MID ADJUST/ TRE ADJUST].
10
Autogood products Internet store “130”
[SETTINGS]
Item
AUX NAME
Selectable setting (Preset: *)
AUX*/ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component.
(Selectable only if “AUX” is selected as the source.)
CLOCK
CLOCK ADJ: (For details, see page 6.)
TIME SYNC: ON*: Synchronizes the RDS station time data and the unit's clock. ; OFF: Cancels.
DIMMER SET: ON: Dims the display illumination. ; OFF*: Cancels.
TEXT SCROLL: AUTO/ ONCE: Selects to scroll the display information automatically, or scroll only once. ;
OFF*: Cancels.
DISPLAY
RDS SET
NEWS SET/ AF SET/ RDS REG/ ATP SEEK: Selectable only if any source other than tuner source is selected.
(For details, refer page 7.)
Troubleshooting
Symptom
Remedy/Cause
Sound cannot be heard.
Adjust the volume to the optimum level.
/
Check the cordand connections.
“PROTECT” appears and no
operations can be done.
Check to be sure the terminals of the speaker leads are cod with insulating tape properly,
then reset the unit. If “PROTECT” does not disappear, consult your nearest service center.
The unit does not work at all.
Reset the unit.
[P-OFF WAIT] does not work.
Radio reception is poor. / Static
noise while listening to the radio.
Turn off the demonstration mode. (pge 6)
Connect the antenna firmly. / Pull the antenna out all the way.
“IN” flashes.
The CD player is not operating properly. Reinsert the disc properly. If the condition did not
improve, turn off the unit ad consult your nearest service center.
CD-R/CD-RW cannot be played
Insert a d CD-R/CD-RW (finalize with the component which you used for
back and tracks cannot be skipped. recording
Disc sound is sometimes
interrupted.
Stop playback while driving on rough roads. / Change the disc. / Check the cords and
connections.
“NA FILE” appears.
“NO DISC” appears.
“TOC ERROR” appears.
The unit is playing an unsupported audio file.
Insert a playable disc into the loading slot.
The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try another
disc instead.
“ERROR 99” appears.
The unit is malfunctioning for some reason. Press the reset button on the unit. If the
“ERROR 99” code does not disappear, consult your nearest service center.
“COPY PRO” appears.
Noise is generated.
A copy-protected file is played.
Skip to another track or change the disc.
Playback order is determined when files are recorded.
Tracks cannot play back as you
have intended them to play.
“READING” keeps flashing.
Longer readout time is required. Do not use too many hierarchies and folders.
Elapsed playing time is not correct. This is caused by how the tracks are recorded.
Correct characters are not displayed This unit can only display letters (upper case), numbers, and a limited number of symbols.
(e.g. album name).
Cyrillic alphabets (upper case) can also be displayed if [RUSSIAN SET] is set to [ON].
(page 4)
Autogood products Internet store “130”
11
Installation/connection
Part list:
Caution
A Faceplate.............................................................. (×1)
If your car's ignition does not have an ACC
B Escutcheon......................................................... (×1)
C Mounting sleeve............................................. (×1)
D Casing for faceplate ...................................... (×1)
E Wiring harness.................................................. (×1)
F Removal tool .................................................... (×2)
position, connect the ignition wires to a
power source that can be turned on and
off with the ignition key. If you connect
the ignition wire to a power source with
a constant voltage supply, as with battery
wires, the battery may die.
Do not use your own screws. Use only the
screws provided.
Install this unit in the console of your
vehicle. Make sure the faceplate will not hit
the lid of the console (if any) when closing
and opening.
Basic procedure
1
Remove the key from the ignition
switch, then disconnect the · terminal
of the car battery.
2
Make proper input and output wire
connections.
\ “Wiring connection” (page 13, 14)
Install the unit to your car.
\ “Installing the unit” (page 14)
Reconnect the · terminal of the car
battery.
After the unit is ialled, check whether
the brake lamps, blinkers, wipers, etc. on
the car are working properly.
Mount the unit so that the mounting angle
s 30° or less.
If the fuse blows, first make sure the wires
aren't touching to cause a short circuit,
then replace the old fuse with one with the
same rating.
Connect the speaker wires correctly to the
terminals to which they correspond. The
unit may be damaged or fail to work if you
share the · wires or ground them to any
metal part in the car.
When only two speakers are being
connected to the system, connect the
connectors either to both the front output
terminals or to both the rear output
terminals (do not mix front and rear).
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
3
4
5
Reset the unit. (page 4)
Warning
The unit can only be installed in a car with
a 12 V DC power supply, negatound.
If you connect the ignition wire (re) and
the battery wire (yellow) to the ar chassis
(ground), you may cause a short circuit,
that in turn may start a fire. Always connect
those wires to the power source running
through the fuse box.
Disconnect the battery's negative terminal
and make all electrical connections before
installing the unit.
Insulate unconnected wires with vinyl tape
or other similar material. To prevent a short
circuit, do not remove the caps on the ends
of the unconnected wires or the terminals.
Be sure to ground this unit to the car's
chassis again after installation.
Mounting and wiring this product requires
skills and experience. For safety's sake, leave
this work to professionals.
If you experience problems during
installation, consult your Kenwood dealer.
12
Autogood products Internet store “130”
Wiring connection
For KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R/ KDC-3251RY
KDC-3251RY
KDC-3051R/ KDC-3051G/
KDC-315A/ KDC-315R
Front output terminals
Rear/subwoofer
output terminals
Rear/subwoofer output terminals
Fuse (10 A)
Antenna terminal (JASO)
Light blue/yellow
KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R: To the
(Steering remote control wire)
steering wheel remote control adapter (optional accessory)
Blue/White
(Power control/motor antenna
control wire)
To the power control terminawhen using the optional power
amplifier, or to the antenna control terminal in the vehicle.
To terminal that is grounded when either the telephone rings
or conversation. (To connect the Kenwood navigation
system, consult your navigation manual.)
Brown
(Mute control wire)
Connecting the ISO connectors on some VW/Audi or
Opel (Vauxhall) automobiles
You may need to modify the wiring of the supplied
Yellow (Battery wire)
Red (Ignition wire)
wiring harness as illustrated below.
Ignition wire
(Red)
A7 (Red)
Vehicle
A4 (Yellow)
Red (A7)
Unit
Yellow (A4)
Battery wire
(Yellow)
ISO connectors
Default wiring
Pin
A4
A5
A7
A8
Color and function
Pin
B1 / B2 Purple
Color and function
Yellow
Battery
ª
/ Purple/black
·
Rear speaker (right)
Front speaker (right)
Front speaker (left)
Rear speaker (left)
Blue/White Power control
B3 / B4 Gray
B5 / B6 White
B7 / B8 Green
ª
/ Gray/black
·
Red
Black
Ignition (ACC)
Earth (ground) connection
ª
ª
/ White/black
/ Green/black
·
·
Autogood products Internet store “130”
13
For KDC-3051RY/ KDC-3051GY
Fuse (10 A)
Antenna terminal (JASO)
White (+) / White/black (–) : To front speaker (left)
Gray (+) / Gray/black (–) : To front speaker (right)
Green (+) / Green/black (–) : To rear speaker (left)
Purple (+) / Purple/black (–) : To rear speaker (right)
Blue
To the antenna control terminal in the vehicle.
(Motor antenna control wire)
Blue/White
(Power control wire)
To the power control terminal when ug the optional power amplifier.
To the terminal that is grounded when either the telephone rings or
during conversation. (To connect the Kenwood navigation system,
consult your navigation manual.)
Brown
(Mute control wire)
Car fuse box
Ignition key switch
Red (Ignition wire)
Yellow (Battery wire)
Car fuse box
Battery
Black (Ground wire)
To the metallic body or chassis of the car
Installing the unit
1
Connect the wiring harness to the unit. Other wiring
connection has been completed earlier. (page 13, 14)
Dashboard of your car
2
Before attaching, make sure
the direction of the
escutcheon is correct. (Wider
hooks on the top side.)
Bend the appropriate tabs
to hold the mounting sleeve
firmly in place.
14
Autogood products Internet store “130”
Removing the unit
1
2
Detach the faceplate.
Engage the catch pin on the removal
tools into the holes on both sides of the
escutcheon, then pull it out.
3
Insert the removal tools deeply into the
slots on each side, then follow the arrows
instructions as shown on the right.
Subject to change without notice.
Specifications
FM tuner section
Audio section
Frequency range (50 kHz space):
87.5 MHz — 108.0 MHz
Maximum output power: 50 W × 4
Output power (DIN 45324, +B = 14.4 V): 30 W × 4
Speaker impedance: 4 Ω — 8 Ω
Tone action: Bass: 0 Hz 8 dB
Middl: 1 kHz 8 dB
Usable sensitivity (S/N = 26 dB): 1.0 μV/75 Ω
Quieting sensitivity (DIN S/N = 46 dB): 2.5 μV/75 Ω
Frequency response ( 3 dB): 30 Hz — 15 kHz
Signal-to-Noise ratio (MONO): 63 dB
Stereo separation (1 kHz): 40 dB
Treble: 10 kHz 8 dB
For KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R/
KC-3251RY
Preout level / load (CD): 2 000 mV/10 kΩ
eout impedance: ≤ 600 Ω
:
MW tuner section
Frequency range (9 kHz space):
531 kHz — 1 611 kHz
Auxiliary input section
Usable sensitivity (S/N = 20 dB): 36 μV
Frequency response ( 3 dB): 20 Hz — 20 kHz
Input maximum voltage: 1 200 mV
Input impedance: 10 kΩ
LW tuner section
Frequency range: 153 kHz — 79 kHz
Usable sensitivity (S/N = 20 dB): 57 μV
General
CD player section
Laser diode: GaAIAs
Digital filter (D/A): 8 Times Over Sampling
D/A converter: 24 Bit
Spindle speed: 500 rpm — 200 rpm (CLV)
Wow & Flutter: Below Measurable Limit
Frequency response ( 1 dB): 20 Hz — 20 kHz
Total harmonic distortion (1 kHz): 0.01 %
Signal-to-Noise ratio (1 kHz): 105 dB
Dynamic range: 90 dB
MP3 decode: Compliant with MPEG-1/2 Audio
Layer-3
WMA decode: Compliant with Windows
Media Audio
Operating voltage (11 V — 16 V allowable): 14.4 V
Maximum current consumption: 10 A
Installation size (W × H × D):
182 mm × 53 mm × 158 mm
Weight: 1.3 kg
About Audio file
Playable Audio file: MP3 (.mp3), WMA
(.wma)
Playable disc media: CD-R/RW/ROM
Playable disc file format: ISO 9660 Level
1/2, Joliet, Romeo, Long file name.
Although the audio files are complied with
the standards listed above, the play maybe
impossible depending on the types or
conditions of media or device.
Autogood products Internet store “130”
15
|