Food Processor
Deluxe
KFP90
Issue 2/04
The appliance is not intended for use by
young children or infirmed persons
without supervision.
Close supervision is required at all times
when operating the appliance near
children.
Young children should be supervised to
ensure that they do not play with the
appliance
Do not let the cord hang over the edge of
a table or counter, touch hot surfaces or
become knotted.
Do not place on or near a hot gas burner,
electric element, or in a heated oven.
Do not leave this appliance unattended
while in use.
This appliance is suitable for domestic use
only. Do not use this appliance for
anything other than its intended use.
Do not use outdoors.
Regularly inspect the power cord, plug and
actual appliance for any damage. If found
damaged in any way, immediately cease
use of the appliance and return the entire
appliance to the nearest authorised
Kambrook Service Centre for
examination, replacement or repair.
Please call 1800 800 634 for Service
Centre details in Australia.
3
Features of your Kambrook Food Processor Deluxe
1. Power control dial – a choice of 3
speeds plus pulse for complete
processing/blending control
splashing when using the processing
blade
11. Stainless steel thin slicing disc – for
slicing vegetables and fruits
2. Motor base - 650 watts of
processing/blending power
12. Stainless steel thick slicing disc – for
slicing vegetables, chicken, meat and
salami
3. Blender jug – 1.5 litre capacity, ideal
for mixing liquids (this must be
correctly locked into the blender
drive or the blender will NOT
operate)
13. Stainless steel fine grating disc – for
grating chocolate and hard cheeses
such as Parmesan
4. Blender jug lid – ensure this is
14. Stainless steel coarse grating disc –
for grating firm cheeses, fruit and
vegetables
correctly in position before activating.
5. Blender jug filler cap – for adding
ingredients whilst blending
15. Stainless steel chipping disc – for
french fries. Also handy for stir fried
vegetables
6. Blender drive cover – this must be
correctly in place before using the
processor, otherwise the processor
will NOT operate (see following
instructions)
16. Stainless steel processing blade – use
for all chopping, mixing and
processing tasks
7. Processor bowl - extra large 1.5 litre
capacity for grating/slicing vegetables,
processing foods, mixing doughs etc
17. Mixing blade – use for making dough
for pastry or bread
18. Disc holder – processing discs simply
lock into place
8. Processing lid and feed chute –
(Processor lid must be fitted
correctly or the processor will NOT
operate)
19. Unique storage holder –
conveniently and safely stores
attachments on top of lid
9. Automatic safety cut out – prevents
the Food Processor Deluxe from
operating unless the processor bowl
and lid, blender jug or blender drive
cover are correctly engaged on the
motor base (not shown)
20. Processing blade protective cover –
for storage when blade is not in use.
21. Processor drive shaft
22. Spatula
23. Non-skid suction feet – for stability
24. Cord storage (not shown)
10. Food pusher with removable inner
80ml Measuring Cup – fits the into
the food chute for safe adding of
foods onto the blades and prevents
Blades must be handled carefully as
they are sharp!
4
10
6
5
1
4
7
2
8
21
3
14
18
19
17
16
20
12
15
13
22
11
23
5
USINGYOUR KAMBROOK
FOOD PROCESSOR DELUXE
Before first use remove any promotional
labels and wash the blender jug, food
processor bowl and all blades in warm,
soapy water. Dry thoroughly.
All blades must be handled carefully
as they are sharp!
Place the motor base on a level, flat
surface.
Note the food processor will not operate unless the
blender drive cover is locked in the correct position
Correct placement of the
Processor Bowl
ASSEMBLY AND OPERATION OF
THE FOOD PROCESSOR
Your Food Processor Deluxe features 3
safety locking devices.
Place the empty bowl onto the base, with
the handle on your right align the arrow
on the processor bowl handle with the
NOTE:THE FOOD PROCESSORWILL NOTWORK
UNLESS ALL OFTHE BELOW ARE IN PLACE:
align arow
on the motor base.Turn
the bowl clockwise until the arrow on the
processor bowl handle is aligned with the
1.The blender drive cover is correctly
LOCKED into position-
'lock' indicator arrow
base.
on the motor
2.The processor bowl is correctly
LOCKED into position
3.The processor lid is correctly LOCKED
into position
NOTE:Always ensure that the Food Processor
Deluxe is disconnected from the power outlet and
operating dial is turned to ‘0’ before assembling or
disassembling the Food Processor Deluxe.
Correct locking procedure of the
Blender Drive Cover
Place cover over drive with the arrow
on the drive cover aligned to the align
arrow
on the motor cover.Turn
clockwise until the arrow on the drive
cover is aligned with lock arrow
on the motor cover.
6
USINGTHE PROCESSING
BLADE/DISCS
Push down
All blades must be handled carefully
as they are sharp!
b.To remove disc, hold disk away and
place thumbs underneath disc at top
of disc marked “push up” and push
out.The disc may be tight for the first
few times.
Using the processing/mixing blade
a. Select either the processing or plastic
mixing blade
b. Place the processing /mixing blade over
the drive shaft and push down.
Using the slicing/grating discs.
a. Select the desired slicing/grating disc and
assemble into the disc holder.To fit the
stainless steel disc onto disc holder, fit
left side of disc (when writing is towards
you), with locating tab into holder, then
push right side down firmly until it locks
into place. Fit the end without the push
up marking in first.Then push the “push
up” side down firmly until it locks into
place.
Correct placement of the
processor lid
Locate tab
Place the lid on top of the bowl, align the
indicator line on the lid with the circle
on the bowl.
7
Turn the lid clockwise – moving the ‘lid
locking tab’ into the slot near the top of
To begin processing/slicing/grating turn the
‘Power Control Dial’ from the Off (0)
the motor unit - until the indicator line on position to either the Low (1), Medium (2)
the lid is aligned with the circle
top of the bowl.
on the
or High (3) speed, depending your
requirements.The speed can be changed
A “click” sound will be heard, to indicate is at any time during the process.
correctly fitted.
For short bursts of power, whilst
NOTE:The Food Processor Deluxe will not operate
unless the processing bowl, lid and blender drive
cover are correctly locked into position.
processing, use the “PULSE” setting.
For slicing and grating – ensure that
the food items you want to slice or grate
are of a suitable size to be feed through
the food chute.
Place the food inside chute and push
down with the ‘food pusher’.
Insert
slot
NOTE! : Never push down any foods with your
hands and do not put your hands down the food
chute at any time during processing.
Lid
locking
tab
For using the processing blade: – with
the ingredients inside the processor bowl,
start the unit on low speed (1) moving to
higher speeds (2 or 3) if necessary. Before
commencing ensure that the ‘food pusher’
is in place to avoid splashing from the food
chute. Ingredients can be added through
the food chute whilst processing.
ꢀ
If ingredients stick to the sides of the
processor bowl during processing, turn
the speed to the Off (0) position, switch
off at the power outlet, remove lid and
then push the food back onto the blades
using the plastic spatula to scrape down
the sides of the bowl.Then recommence
processing.
Ensure the speed dial is in the Off (0)
position.
Plug into a 230/240 volt power outlet.
Turn power on.
NOTE: Do not over fill the processor bowl past the
MAX line for solids and past the 750ml mark for
liquids. For greater quantities of liquids the blender
jug should be used.
The processor is now ready to use.
8
When processing is complete, turn to the
Off (0) position.Wait until blades have
stopped rotating before removing the lid,
blades or processor bowl.
Align the arrow on the lower edge of
the blender jug with the align handle
arrow
on the motor cover.Turn the
blender jug clockwise until the arrow on
the blender is aligned with the lock handle
ASSEMBLY AND
OPERARTION OFTHE
BLENDER
arrow
on the motor cover, a “click”
sound will be heard.
Your Food Processor Deluxe blender
features 2 safety locking devices.
NOTE: the blender will not operate unless:
1.The blender jug is correctly positioned
and LOCKED onto the motor base
2.The processor bowl AND lid are
correctly locked into place (refer to
previous instructions)
ꢀ
NOTE:The food processor will not operate while
the blender jug is assembled to base. If processing
is required, remove the blender and fit the Blender
Drive Cover.
Ensure the speed dial is in the Off (0)
position.
Correct placement of the
blender jug
Unlock and remove the blender drive cover.
Plug into a 230/240 volt power outlet.
Turn power on.
The blender is now ready to use.
Place ingredients into the jug. Note do not
overfill the jug (ie/ above the MAX mark).
Firmly fit the lid to the top of the blender.
Ensuring that the ‘filler cap’ (inside the lid)
is correctly locked into position.
With your hand on top of the blender lid
initially, turn the ‘Power Control Dial’ from
the Off (0) position to either the Low (1),
Medium (2) or High (3) speed, depending
your requirements.The speed can be
changed at any time during blending.
9
For short bursts of power, use the
“PULSE” setting.
MAINTAININGYOUR
KAMBROOK FOOD
PROCESSOR DELUXE
Always turn the power off at the power
outlet and then unplug before
disassembling any parts.
If ingredients stick to the sides of the jug
during blending, turn the speed dial to the
Off (0) position, switch off at the power
outlet, remove lid and then push the food
back onto the blades using the plastic
spatula to scrape down the sides of the
jug.Then replace lid and recommence
blending.
Wash the blender jug, lid, filler cap,
processor bowl, blades, food pusher in
warm soapy water after each use. Rinse
thoroughly and dry.
Ingredients can be added during blending
by removing the ‘filler cap’ and
placing/pouring additional ingredients
through the hole.
Do not soak steel parts.
The processing blade and slicing/grating
discs are extremely sharp! Use caution
when handling and storing these parts.
Always store the processing blade with
the protective covers provided.
Note: Do not overfill the blender jug above the
MAX mark.
This blender is not recommended for
blending dry ingredients.
Store the food processor with the
processing blade in the bowl and the lid
and the food pusher in position, but DO
NOT lock as this places unnecessary
strain on the operating switch.
When blending is complete, turn to the
Off (0) position.Wait until blades have
stopped rotating before removing the lid
or jug.
Never use an abrasive cleaner. Do not
place any parts in the dishwasher.
Wipe the motor base with a soft, damp
cloth.
DO NOT immerse the motor base, power
plug or cord in water or any other liquid.
THE STAINLESS STEEL
PROCESSING BLADE
The cutting edges of this blade are
extremely sharp, it should only ever be
held by the central plastic spindle.
ALWAYS store the blade with the
protective cover provided.
10
CHOPPING
USE PROCESSING BLADE
INGREDIENTS PROCEDURE
ONIONS,
VEGETABLES,
FRUITS,
Cut ingredients into approximately 2.5cm cubes. Place in processing
bowl, up to 750g at a time. Process, using the PULSE switch until the
ingredients are chopped as desired. Remove lid and scrape the sides
COOKED MEATS down with the spatula between pulses to ensure more even chopping.
RAW MEATS
(BONELESS)
Trim the meat of fat and gristle, remove any bones. Cut into 2.5cm
cubes. Process up to 750g at a time on speeds 2-3, scraping down
the sides of the bowl, until the meat is coarse or fine as desired.
HERBS
Make sure the herbs are as dry as possible. Place in the processing
bowl and process on speeds 2-3, until finely chopped. Scrape down
the sides of the bowl at least once during processing. Up to 4 cups
of firmly packed herbs can be processed at a time.
BREADCRUMBS
OR BISCUIT
CRUMBS
Quarter the slices of bread and break up the biscuits. Place them in
the processing bowl and process using speed 2. Process up to 1 ⁄2
loaves of bread, crusts removed, or 1 loaf with crusts, at a time.
Use stale bread for dry breadcrumbs.
1
NUTS (SHELLS
REMOVED)
Place up to 2 cups of nuts in the processing bowl at a time and
process using the PULSE switch. If chopped too finely the nuts will
become oily and eventually form a butter. Processing smaller
quantities at one time will ensure even chopping.
HARD CHEESES
To process hard cheese such as Parmesan, first cut the cheese into
2 cm cubes.Turn the Food Prcessor Deluxe onto speed 1, and
drop cubes of cheese down the feed tube, processing 200g at a time.
HARD BOILED
EGGS
Shell and halve the eggs before placing in the processing bowl.
Process using the PULSE switch.
PUREEING
USE PROCESSING BLADE
INGREDIENTS PROCEDURE
COOKED SOUPS, Place up to 4 cups of mixture in the processing bowl and process
SAUCES
on speeds 2-3, until desired consistency is reached.
(1ltr OR LESS)
DIPS, SPREADS
Place ingredients in the processing bowl and process on speeds
2-3. If some ingredients are to remain in pieces, add them last and
mix in using the PULSE switch.
COOKED
These may first be cooked in a saucepan. Process on speed 3 until
VEGETABLES, FRUIT desired consistency is reached.
11
MIXING
USE MIXING BLADE
INGREDIENTS PROCEDURE
PACKET CAKES
BATTER –
Place all the ingredients in the processing bowl. Process for 5
seconds using speed 3, remove lid and scrape down the sides of
the bowl. Process for another 5-10 seconds.
Place all ingredients in the processing bowl and process on speeds
PIKELETS, CREPES, 2-3 until combined, scrape sides of the bowl down once during
PANCAKES
processing. Do not fill above the 750ml fill line.
QUICK MIX
CAKES
These are usually a melt and mix method.Add ingredients in the
order specified in the recipe. Be careful not to over mix.
SHORT CRUST
PASTRY AND
SCONES
Place the flour and butter in the processing bowl and process using
speed 2 until butter is rubbed in.With the motor running pour the
liquid down the feed tube and process until mixture forms a ball,
approximately 30 seconds. Do not mix more than 2 cups of flour
at a time.
BISCUITS AND
CHAMPAGNE
PASTRY
Place butter, sugar and egg yolks in the processing bowl and process
on speeds 2-3 until just combined. Remove lid, add the flour and
mix until just combined using the PULSE switch. Do not mix more
than 4 cups of flour at a time.
YEAST DOUGHS Add ingredients in the order listed in the recipe.Add liquids
through the feed tube with the motor running.
NOTE!When mixing liquids with the processing blade, do not fill above the bowls 750ml fill line. Do not
use the highest speed 3 as liquids will spill over the bowl.
THE STAINLESS STEEL SLICING DISCS
For a wider choice of slicing options, we have included a thick and thin slicing disc.
For all foods, pack food into the feed tube firmly to ensure even results.Although firm
pressure on the food pusher is recommended for some foods, do not press hard as the
disc may jam.
Always use the food pusher when using the slicing disc. Use speed 2-3 for best results.
NOTE! Either the thick or thin slicing disc can be used for the ingredients listed on next page.
12
INGREDIENTS PROCEDURE
ONIONS
Peel the onions and halve if too large to fit into the feed tube.
Place the onions in the feed tube, cut edge down. Process, exerting
firm pressure on the food pusher.
CARROTS,
ZUCCHINI,
EGGPLANT,
BANANAS
Prepare the foods in the usual way. For rings arrange foods
vertically in the feed rube, cutting them so they are even in height.
For slices arrange foods horizontally in the feed tube.
Process by exerting firm pressure on the food pusher.
CAPSICUMS
Remove the core and seeds. Halve the capsicums if necessary and
arrange them vertically in the feed tube. Process using firm
pressure on the food pusher.
MUSHROOMS
Wipe the mushrooms and pack in the feed tube on their sides.
Process using firm pressure on the feed pusher.
APPLES, PEACHES Peel if desired, remove the stone and quarter the fruit. Lie the
quarters on their sides in the feed tube and process using firm
pressure of the food pusher.
BEANS
Prepare the beans. Cut into lengths and pack horizontally into the
feed tube. Process using firm pressure on the food pusher.
CHEESE
Cut the cheese into pieces large enough to just fit the feed tube.
Process using light pressure on the feed tube to prevent cheese
crumbling.
CABBAGE
LETTUCE
Cut cabbage into wedges to fit feed tube and process using firm
pressure.
Separate the leaves of the lettuce and wash and dry. Roll the leaves
firmly and pack into the feed tube. Process using firm pressure.
RAW MEAT, FISH, Trim meat of fat and gristle and cut to fit snugly in the feed tube.
CHICKEN Freeze until partly frozen. Process using firm pressure.
COOKED MEATS, Pack the feed tube snugly placing meat in the feed tube vertically.
CABANOSSI,
SALAMI
Process using firm pressure. For more even slicing remove sausage
skins first.
CUCUMBERS
Trim the ends of the cucumber and cut into lengths to fit the tube
vertically. If the cucumber is too wide, scoring it length wise with a
fork will make it more pliable.
POTATOES
Peel the potatoes and cut into pieces if necessary to fit the feed
tube. Process using firm pressure.
13
THE STAINLESS STEEL COARSE GRATING DISC
For a wider choice of grating options we have included a coarse grating disc as well as a
fine grating disc.
For all foods, pack the tube firmly to ensure even results.Although firm pressure on the
food pusher is recommended for some foods, do not press hard as the disc may jam.
ALWAYS use the food pusher when using the grating discs.
INGREDIENTS PROCEDURE
ONIONS,
POTATOES
Pack into the feed tube and process using firm pressure.
Peel and cut into pieces if necessary to fit the feed tube.
CARROTS,
ZUCCHINI,
CUCUMBER
Prepare the vegetables and pack into the feed tube. Packing vertically
will give shorter shreds than packing horizontally. Process using
firm pressure.
CHEESE
Cut the cheese to fit the feed tube snugly. Process using a light
pressure on the food pusher to prevent the cheese crumbling.
THE STAINLESS STEEL FINE GRATING DISC
Use speed 2 for best results
ALWAYS use the food pusher when using grating discs.
INGREDIENTS PROCEDURE
CHOCOLATE
Break chocolate into pieces to fit the feed tube and process using
firm pressure.
PARMESAN
CHEESE
Cut the cheese to fit the feed tube snugly. Process using light
pressure on the food pusher to prevent the cheese crumbling.
ONIONS
Peel the onions and chop into halves. Place onions in the feed tube,
cut edge down. Process using firm pressure
GARLIC AND
GINGER
Peel and place minimum 250g into the feed tube and process using
firm pressure. Note : If small quantities are used, they may block
the holes in the grating disc.To help wash the ingredients through,
pour ⁄4 cup olive oil (for garlic) or ⁄4 cup sherry (for ginger) down
feed tube. Excess amount can be stored for later use.
1
1
14
THE STAINLESS STEEL CHIPPING DISC
The chipping disc makes french fries from potatoes and also pumpkin or kumera (sweet
potato) for something a bit different.
ALWAYS use the food pusher when using the chipping disc.
INGREDIENTS PROCEDURE
POTATOES,
KUMERA,
PUMPKIN
Prepare the vegetables, pack into the feed tube and process using
firm pressure.
THE BLENDER JUG
INGREDIENTS PROCEDURE
1
DRINKS,
MILKSHAKES
Fill the jug to at least ⁄4 full. Remember to leave room to allow froth
to form as the drink is aerated.
SOUPS, SAUCES
Place mixture in the jug and blend on speeds 2-3, until desired
(PUREEING LESS consistency.
THAN 1 LITRE)
MAYONNAISE,
MARINADES,
DRESSINGS
Pour oil into the jug gradually through the opening in lid, with
motor running. Blend on speed 2.
15
Using the processing blade on
speed 3
RECIPES ONTHE RUN
AVOCADO CREAM DIP
Uses : Nacho’s, Mezze Plate
1. Place all ingredients in the processing
bowl and process until smooth.
1 ripe avocado, peeped and chopped
4 shallots, sliced
PANFRIED LAMB WITH SUN-
DRIEDTOMATOES
Serves 6
1
1 ⁄2 tablespoons lemon juice
1
6 lamb leg steaks
⁄
2
teaspoon salt
1
1 tablespoon olive oil
2 cloves garlic, crushed
1 ⁄2 teaspoons Worcestershire sauce
1
⁄
4
cup sour cream
125g cream cheese
SUN-DRIEDTOMATO SAUCE
Uses: soup base, base of salad dressing,
pasta, sauce for beef, pork, lamb and
chicken
Using the processing blade on
speeds 2-3
1. Place all ingredients into the processing
bowl and process on speeds 2-3 until
mixture is pureed and shallots are finely
chopped.
2
⁄
3
cup drained sun-dried tomatoes,
chopped
1
⁄
3
cup pitted black olives
2. Serve with corn chips or vegetable
strips (vegetable strips can be made using
the chopping blade).
2 cloves garlic, crushed
1
1 ⁄2 tablespoons olive oil
2 teaspoons fresh oregano, chopped
HOMMOS
Serves 6
1. Heat oil in a heavy based frypan, add
lamb and garlic.
Uses: Dip, sauce, spread, thickener
2 cups chick peas, canned or precooked
2 cloves garlic, peeled
2. Cook lamb for 2-3 minutes each side.
3. Serve with sun-dried tomato sauce
SUN-DRIEDTOMATO SAUCE
Using the processing blade on
speed 3
2 tablespoons plain yogurt
1 teaspoon paprika
1 teaspoon tahini
1. Place sun-dried tomatoes, olives, garlic
and olive oil in the processing bowl and
process until pureed and well combined.
Stir oregano through the sauce, heat
through and pour over lamb steaks.
1 tablespoon olive oil
16
GRILLED CHICKEN WITH PESTO
Serves 6
Using the thick slicing disc on
speed 3
1. Slice leeks, onions and potatoes using
the thick slicing disc.
Pesto uses: on chicken, lamb, potatoes, pasta
6 chicken breast fillets, skin removed
PESTO
2. Melt butter in a saucepan and sauté
leeks and onions until tender.
3.Add potatoes, chicken stock, salt and
pepper and simmer for 10 minutes.Allow
to cool.
1 bunch basil
60g pinenuts
2 cloves garlic, roughly chopped
Using the processing blade on
speed 3
60g fresh Parmesan cheese, grated
4. Blend the soup in the processing bowl
until smooth, in two batches.
1
⁄
2
cup olive oil.
1. Grill chicken fillets and serve hot with
fresh pesto.
5. Return the soup to saucepan, stir
through cream and reheat gently.
6. Do not allow to boil.
PESTO
Using the processing blade on
speed 3
1. Place basil, pinenuts, garlic and Parmesan
in the processing bowl, process until well
combined.
PUMPKIN AND CUMIN SOUP
Serves 6
500g butternut pumpkin, peeled and
roughly chopped
2 potatoes, peeled and roughly chopped
2 onions, peeled and quartered
3 cups stock, vegetable or chicken
2 teaspoons ground cumin
2. Using speed 1 with the motor running,
gradually add the olive oil and process
until well combined.
SOUPS
pinch of salt
POTATO AND LEEK SOUP
Serves 6
Sour cream and chives to serve
Using the processing blade on speed 3
3 leeks, washed and tops removed
2 onions, peeled
1. Place all ingredients in a saucepan and
simmer for 15 minutes or until pumpkin is
tender.Allow to cool.
3 large potatoes, peeled and roughly
chopped
2. Pour cooked ingredients into the
processing bowl and process speed 3 until
smooth.
60g butter
5 cups chicken stock
3. Serve with sour cream and chives.
salt and pepper to taste
3
⁄
4
cup cream
17
PRAWN LAKSA
Serves 4
5. Place noodles and sprouts in serving
bowl and spoon laksa over the top.
125g fresh ginger, peeled and roughly
chopped
TABOULI
Serves 8
2 small red chillies, seeds removed
2
⁄
3
cup cracked wheat
4 stalks lemon grass, peeled and roughly
chopped
1
1 ⁄2 cups parsley sprigs
3
⁄
4
cup mint leaves
1
⁄
3
bunch coriander
1 clove garlic, chopped
3 cloves garlic, peeled
3 large tomatoes, quartered
3 tablespoons peanut oil
1 teaspoon shrimp paste
2 tablespoons green curry powder
1 medium onion, peeled and quartered
1
⁄
⁄
4
cup olive oil
1
4
cup lemon juice
500g green king prawns, shelled and
deveined
1. Cover cracked wheat with boiling water
and stand for 15 minutes. Drain and pat
dry with paper towel.
3 cups/750ml coconut milk
500g packet Asian style noodles, cooked
(follow directions on packet)
Use the processing blade on speed 3
1. Place parsley, mint and garlic into
processing bowl and process until finely
chopped.
200g fresh bean sprouts
Using the processing blade on
speed 3
3.Add oil, lemon juice and cracked wheat
and pulse until combined.
1. Place ginger, chillies, lemongrass,
coriander into processing bowl.
COLESLAW
2. Process until ingredients are finely
chopped.
Serves 8-10
6 sticks celery
3. Heat oil in a saucepan and add the
processed herbs, shrimp paste and curry
powder. Cook stirring over a moderate
heat for 4-5 minutes until mixture has
softened.
8 shallots
1
⁄
4
red cabbage, separate leaves and roll
into bundles
1
⁄
4
white cabbage, separate leaves and roll
4.Add prawns and coconut milk. Cook
gently until prawns are opaque and
cooked through.
into bundles
4 carrots, peeled
18
3 green apples, cored and quartered
1 red capsicum
30g butter or margarine
2 tablespoons plain flour
1
3
1 ⁄2 cups mayonnaise
⁄
⁄
4
cup milk
1
Using the thick slicing disc on
speed 2
2
cup cream
1 x 450g packet instant lasagne sheets
1. Slice celery, shallots and cabbage, place
into large bowl
Using processing blade on speed 3
1. Place steak, onion and garlic in
processing bowl and process until finely
chopped.
Using the coarse grating disc on
speed 2
2. Process carrots and place in bowl with
cabbage.
2. Heat oil in a frypan and add meat
mixture. Cook until browned, add
tomatoes, tomato paste and herbs.Allow
to simmer for 20 minutes.
Using the processing blade on
speed 2
3. Pulse apple & capsicum until roughly
chopped.
CHEESE SAUCE
Using the coarse grating disc on
speed 3
4.Add mixture to the cabbage. Place
mayonnaise into bowl with cabbage and
combine well.
1. Grate tasty cheese
2. Melt butter in a small saucepan.Add
flour, stir until smooth, cook for 1 minute.
5. Refrigerate before serving.
LASAGNE
Serves 4-6
3.Add milk and cream stirring over
medium heat until sauce boils and
thickens. Simmer for 3 minutes, add
cheese and stir until cheese melts.
500g chuck steak, cubed
1 onion, peeled and quartered
2 cloves garlic
4. Place 1/2 of the meat sauce in the base
of the lasagne dish. Pour 1/2 of the cheese
sauce over the top.Assemble lasagne
sheets over the cheese sauce and then
repeat the procedure.
2 tablespoons vegetable oil
440g can tomatoes
2 tablespoons tomato paste
1 tablespoon mixed herbs
CHEESE SAUCE
5. Bake in moderate oven for 20 minutes.
90g tasty cheese
19
FISH AND PRAWN CAKES WITH
PEANUT SAUCE
BASIC BUTTERCAKE
185g butter or margarine, cubed
Makes 12
1 cup sugar
1
300g fish fillets
⁄
2
teaspoon vanilla
600g green prawns, peeled and deveined
3 eggs
3 cups self-raising flour
1 tablespoon Penang curry paste
3
1
⁄
4
cup milk
⁄
2
cup dessicated coconut
1 teaspoon ground black pepper
3 chillies, seeds removed
2 tablespoons brown sugar
Peanut Sauce
Using the mixing blade on speed 3
1. Place butter, sugar and vanilla into the
processing bowl and process until light
and fluffy.
2.While motor is running, add eggs one at
a time through the feed tube, until well
combined. Gradually add remaining flour
and milk through the feed tube until
mixture is well combined (approx 1
minute).
1 teaspoon sesame oil
1 clove garlic, peeled and chopped
2 small red chillies, chopped
1
⁄
2
cup crunchy peanut butter
3. Remove the mixture from the bowl into
a well greased, deep 20cm square cake tin
and bake in moderate oven (180ºc) for
approximately 40 minutes or until golden
brown.
1 cup water
2 tablespoons soy sauce
1
⁄
4
cup coconut milk
Using the processing blade on speed 2
1. Place fish and prawns in the processing
bowl and process until minced finely. Add
coconut, curry paste, pepper, chillies and
sugar and process until well combined.
Mould tablespoons of the mixture into
round patty shapes and grill or barbecue
until golden brown. Serve hot with peanut
sauce.
VARIATIONS
LIGHT SULTANA CAKE
Add 1-cup sultanas after the addition of
flour and milk, pulsing sultanas through
until just combined.
CHERRY CAKE
Add 125g diced glace cherries after the
addition of the flour and milk, pulsing
through until just combined.
Peanut Sauce
1. Heat sesame oil in saucepan. Add garlic
and chillies and sauté for 1 minute. Stir in
peanut butter, water and soy sauce. Heat
stirring until well combined and thickened.
Fold through coconut milk and serve.
20
CHOCOLATE MUD CAKE
POWER SHAKE
1 tablespoon white vinegar
2 tablespoons cocoa powder
1 cup milk
1 teaspoon instant coffee
2 tablespoons boiling water
2 tablespoons sugar
1 egg
1 cup plain flour
1 cup self-raising flour
1 cup castor sugar
3
⁄
4
cup cocoa
1 teaspoon wheat germ
2 cups cold milk
1/2 teaspoon bicarbonate of soda
125g butter or margarine
3 eggs
1. Dissolve cocoa and coffee in boiling
water. Combine with sugar, egg, wheat
germ and milk. Pour into blender jug.
Blend on speed 3, until smooth and frothy.
Serve immediately.
Using the mixing blade on speed 2
1.Add vinegar to milk and allow to stand
for 5 minutes.
BANANA SMOOTHIE
2 bananas, peeled and chopped
2. Place flour, sugar, cocoa and bicarbonate
of soda into the processing bowl and
process until combined.Add melted
butter, egg and milk and process until
smooth.
1 cup plain yoghurt
1 cup milk
1
⁄
2
cup honey
3. Pour mixture into a greased 20cm ring
and bake in a moderate oven (180ºc) for
40 – 45 minutes or until cooked.
1. Place bananas, yoghurt, milk and honey
into the blender jug. Blend on speed 3
until well combined. Serve immediately.
MANGO SMOOTHIE
2 mangoes, peeled and sliced
CHEESY BREAD ROLLS
500g bread flour
1
1 ⁄2 cups plain yoghurt
310ml Tepid water
1 tablespoon sunflower oil
1 teaspoon salt
1 cup orange juice
1. Place mangoes, yoghurt and orange juice
into the blender jug. Blend on speed 3
until smooth. Serve immediately.
1 teaspoon sugar
3
1 ⁄4 teaspoon dry yeast
150g grated cheese
1. Place the water, oil, and then all the dry
ingredients into the processing bowl with
the dough blade.
21
2. Process using speed 3 for up to 15
seconds, adding more water if necessary
to form a ball.
Using the mixing blade on speed 2
1. Place the flour, salt and butter into the
processing bowl and process until mixture
resembles fine breadcrumbs.While the
motor is running, pour water down the
feed tube until mixture forms a ball
around blade.
3. Remove the dough from the bowl and
place onto a lightly floured surface to
knead.
4. Place the kneaded dough into a greased
glass bowl, cover with plastic wrap and
place in a warm position until the dough
has doubled in size. (Approximately 30-40
minutes).
2.Wrap the pastry in plastic wrap and
efrigerate for 15 minutes before using.
3. Use as desired.
SCONES
5. Remove the dough and cut into 4,
flatten the pieces and place some grated
cheese onto the dough; Fold the top
corner into the centre of the dough; then
fold each side to meet itself and roll
inwards to form a roll and place on a
greased baking tray.
Makes 18
3 cups self-raising flour
1
⁄
4
teaspoon salt
45g butter or margarine
200ml milk
6. Place the tray in a warm position until
the rolls have doubled in size.
milk for glazing
Using the mixing blade on speed 1
7. Bake in a moderate oven (180º-200ºC)
for 15-20 minutes.
1. Place the flour and salt into the
processing bowl and process until well
combined.Add the butter and process
until mixture resembles fine breadcrumbs.
While motor is running, gradually pour the
required amount of milk down the feed
tube until mixture forms a ball around the
blade (approx 30 seconds), do not
overmix the dough as this will toughen the
scones.
NOTE! Other fillings can be incorporated in the
same way ie. pesto, mustard and grains
SHORTCRUST PASTRY
Makes sufficient to line a 20cm pie base
cover
2 cups flour
1
⁄
2
teaspoon salt
125g butter or margarine
2 tablespoons water
2. Place the dough on the floured board
and knead lightly. Cut into rounds with a
scone cutter. Place each close together on
a lightly greased oven slide. Glaze with
milk and bake in a hot oven (230º-250ºC)
for 12-15 minutes or until brown.
22
PIZZA DOUGH
Makes 1 large pizza or 2 medium pizzas
2 cups plain flour
1 teaspoon salt
1 teaspoon sugar
7gms dried yeast
30g butter or margarine
1 egg
125mls warm milk
Using the processing or mixing blade
on speed 3
1. Place the flour, salt, sugar and yeast into
the processing bowl, add butter and egg,
process until well combined, gradually add
milk to combined dry ingredients down
the feed tube whilst the unit is running.
Process until well combined and the
dough forms a ball around the blade.
Remove the dough and knead lightly until
smooth and elastic. Shape the dough into a
ball, place in a bowl and cover and stand
for 30 minutes or until dough has doubled
in size.
2. Halve the dough and roll until the size
of the pizza tray. Spread the dough with
desired toppings.
3. Bake in hot oven for 20 minutes.
23
Notes
24
Notes
25
Notes
26
KAMBROOK
12 MONTH
REPLACEMENT WARRANTY
KAMBROOK warrants the purchaser
against defects in workmanship and material,
for a period of 12 months from the date of
purchase (3 months commercial use).
If the product includes one or a number
of accessories only the defective
accessory or product will be replaced.
In the event of KAMBROOK choosing to
replace the appliance, the guarantee will
expire at the original date, ie. 12 months
from the original purchase date.
Guarantee and purchase receipt for this
product are to be retained as proof of
purchase and must be presented if making
a claim under the terms of the
In Australia, this KAMBROOK Guarantee
is additional to the conditions and
guarantees which are mandatory as
implied by the Trade Practises Act 1974
and State Territory legislation.
KAMBROOK guarantee.
KAMBROOK reserves the right to
replace or repair the appliance within
the warranty period.
For service, spare parts or product
information in Australia, please call
KAMBROOK on the customer Service
Line (free call) 1800 800 634.
Warranty does not apply to any defect,
deterioration, loss or injury or damage
occasioned by, or as a result of the misuse
or abuse, negligent handling or if the
product has not been used in accordance
with the instructions.The guarantee
excludes breakages and consumable items
such as slicing and processing discs.
For service, spare parts or product
information in New Zealand, please
call KAMBROOK New Zealand,
Greenmount, Auckland Phone 0800 273 845
Fax 0800 288 513. For spare parts phone
0800 273 845.
This warranty is void if there is evidence
of the product being tampered with by
unauthorised persons.
If claiming under this guarantee the product
must be returned to freight prepaid.
YOUR PURCHASE RECORD (Please complete)
Attach a copy of purchase
receipt here.
DATE OF PURCHASE___________________________
MODEL NUMBER _____________________________
SERIAL NUMBER (If applicable) ___________________
Please don’t return purchase record
unless you are making a claim
PURCHASED FROM ___________________________
Issue 2/04
Kambrook 4 Kingston Town Close Oakleigh,Victoria 3166,Australia
Customer Service Line (free call) 1800 800 634 Customer Service Fax 1800 621 337
Kambrook (New Zealand) Mono Place Ellerslie,Auckland, New Zealand
Customer Service Line/Spare Parts 0800 253 007 Customer Service Fax 0800 263 001
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the one illustrated in this book. Issue 2/04
|