JVC WR MG88U User Manual

INSTRUCTIONS  
BRUKSANVISNING  
NÁVOD K OBSLUZE  
INSTRUKCJA OBSŁUGI  
HASZNÁLATI UTASÍTÁS  
ИНСТРУКЦИЯ ПО  
ЭКСПЛУАТАЦИИ  
使用說明書  
ENGLISH  
DEUTSCH  
FRANÇAIS  
NEDERLANDS  
CASTE.ESP.  
ITALIANO  
PORTUGUÊS  
DANSK  
BEDIENUNGSANLEITUNG  
MANUEL D’UTILISATION  
GEBRUIKSAANWIJZING  
MANUAL DE INSTRUCCIONES  
ISTRUZIONI  
INSTRUÇÕES  
INSTRUKTIONSBOG  
KÄYTTÖOHJE  
ဧ፿ႁීၗ  
사용 설명서  
BRUKSANVISNING  
WR-MG88U  
Marine Case  
Undervattenshus  
Marine kassen  
Podvodní pouzdro  
Podwodna obudowa  
Tengeri tok  
Бокс для подводной съемки  
潛水盒  
༅ၺఫ  
SUOMI  
Unterwassergehäuse  
Boîtier sous-marin  
Onderwaterhuis  
Carcasa submarina  
Custodia subacquea  
Caixa Aquática  
SVENSKA  
NORSK  
ČEŠTINA  
POLSKI  
Vandtæt kameraetui  
Vesitiivis kotelo  
수중용 케이스  
MAGYAR  
РУССКИЙ  
中文繁體  
ᒦᆪ଼ᄏ  
한국어  
3. Check that there are no scratches or cracks  
on the marine case every time you use it.  
The marine case must withstand water pressure  
with use. Repeated exposure to pressure  
eventully leads to material fatigue, which may  
result in damage of the marine case. Every time  
you use the marine case, check in advance  
that there are no scratches or cracks. If you  
frequently use the marine case, be sure to ask for  
maintenance at the store of purchase. (There is a  
charge for maintenance.)  
Accessories  
Glass cleaner (to prevent “steaming up”)  
Cleaning fluid (to remove dirt)  
Silicone grease  
Silicone cloth  
Silica gel (Preservative)  
Lens tissue paper  
Swab  
Strap  
2 O-rings : 1 Spare  
To protect your camera and ensure optimum use,  
keep the examples listed above in mind when using  
the marine case.  
JVC accepts no responsibility for water leakage or  
damage to anything inside the marine case (camera,  
SD card, etc.) due to careless usage of  
this product. Be sure to follow correct procedures  
when using the marine case.  
Base (A,B)  
The attachment base differs  
depending on the model of  
camera that you have.  
Grip  
Commercially available  
lights and weights can also  
be attached.  
Pick  
Screw tightening key  
2 hexagonal wrenches  
Large: for assembling grip  
Small: buckle opener  
Lens hood  
Only attached to certain  
types of cameras.  
Maintenance Kit – Sold Separately (Part  
Number: MG8_MTKIT)  
You can purchase the following set of expendable  
parts. Please contact your local JVC service  
representative.  
O-Ring x2  
Silicone grease (5 g) x1  
Silica Gel (preservative) (2 g) x5  
Lens tissue paper (50 sheets) x1  
3
Index  
Preparation  
Inspect the main casing for scratches and  
cracks etc.  
1
Apply 2 or 3 drops of the glass cleaner provided  
onto one of the lens tissues or a clean cloth, and  
wipe the inner side of the marine case front glass.  
Strap  
Front glass  
Check the O-ring.  
2
Using the supplied pick, remove the O-ring from  
the main case.  
Bottom view  
Main casing grip:  
!
Attach the included strap as shown in the diagram  
above.  
Zoom lever  
Check the O-ring, O-ring contact surface, and  
groove in which the O-ring fits for dirt, scratches,  
or damage etc. visually and by touching with your  
finger.  
#
$
Ring:  
Commercially available filters (67mm diameter)  
etc can be attached.  
Buckles (4 places):  
Seal the marine case.  
Grip attachment holes:  
You can attach the included grip, or commercially  
available weights etc.  
%
&
Apply grease to the O-ring and re-attach.  
3
4
Close the empty marine case (no camera  
inside).  
Still image shooting button  
Video recording start/stop button  
Power/mode switch lever:  
Turns camera’s power on/off, or switches video or  
still mode.  
(
)
*
Place the marine case in water, and check  
that there are no water leaks.  
5
4
5 Insert the camera into the marine case.  
Attaching the Marine Case to the Camera  
Inserting the provided silica gel between the  
camera and marine case prevents the inside of  
the marine case from steaming up.  
1 Pull the power/mode switch lever of the  
marine case in the direction of the arrow  
(Q), and rotate it to lock it (R).  
Silica gel  
If the power/mode switch lever is not locked,  
it may touch or damage the camera when the  
camera is put into the case.  
Tighten the  
grip belt.  
Base attachment groove  
Base  
Marine case internal base  
For cameras that are equipped with Base A,  
attach the lens hood.  
2 Attach the base in the correct way for your  
model of camera. (pg. 7)  
Line up the tripod screw hole on the base of  
your camera with the base holes of the case,  
and tighten the screw.  
Install the battery (and insert an SD card if  
needed) beforehand.  
6 Seal the marine case, and attach the grips.  
Lock in all 4  
places.  
3 Setup the camera (please refer to your  
camera’s instruction manual).  
Turn off the flash and light. (presence of a flash/  
light differs according to the model.)  
Switch off the power.  
It is recommended to set to the auto recording  
mode.  
Open the lens cover.  
4 Open the marine case.  
If it is difficult to open buckles, use the buckle  
opener.  
NOTE  
Hexagonal  
The risk of water leakage is extremely high if the  
O-ring is twisted, if you forget to attach it, or if  
something is trapped in the seal.  
wrench (small)  
5
2 Press the video recording start/stop button  
or the still image shooting button to start  
recording.  
Recording the Video/Still Image Files  
Before recording  
Submerge the marine case with the camera  
equipped into a bathtub or water tank full of fresh  
water.  
Still image shooting button  
Gradually increase the amount of time the marine  
case is submerged as shown below.  
Zooming  
(Telephoto)  
1st time: 5~10 seconds  
2nd time: 30 seconds ~ 1 minute  
3rd time: 3 minutes ~ 5 minutes (try operating  
Zooming  
(Wide angle)  
the levers and buttons while the marine case is  
submerged).  
Video recording start/stop button  
NOTES  
Always have someone hold the marine case for  
you when diving into, or getting out of water.  
If for any reason water leakage occurs, remove  
the camera battery. It may cause the camera to  
explode.  
3 When you have finished recording, rotate  
the power/mode switch lever to turn the  
camera’s power off.  
The camera’s power lamp goes out.  
1 Pull the marine case power/mode switch  
lever to release the lock, and switch on the  
camera’s power.  
Rotate the lever to switch on the camera’s power.  
The camera’s power lamp lights.  
NOTE  
Sometimes, due to sudden shaking or impact to the  
marine case, the camera’s drop detection function  
operates to switch off the camera’s power.  
When [VIDEO MANAGEMENT FILE IS BROKEN.  
TO RECORD/PLAYBACK VIDEO, RECOVERY IS  
REQUIRED. RECOVER?] is displayed, press the  
REC button to recover the file.  
Switching between video/still modes  
8
Switch modes by rotating the lever.  
6
Detaching the Marine Case/Maintenance  
Storing the O-ring  
Always perform maintenance on the marine case  
after you have finished recording. Failing to perform  
maintenance on the marine case will allow dirt to  
build up on the case, causing water leaks.  
If you do not intend to use the marine case for longer  
than 1 month, remove the O-ring from the marine  
case, and spread a thin layer of the supplied silicone  
grease over the entire O-ring. After that, place the  
O-ring inside a clean plastic bag, and store it in the  
maintenance kit case.  
1 Wash the marine case in water while it is  
The O-ring is an expendable part. Replace the  
O-ring with a brand new one every year.  
still sealed.  
If the marine case was used in seawater, we  
recommend submerging the marine case in  
fresh water for a while to remove salt.  
NOTES  
When re-using an O-ring after storage, always  
check the condition of the O-ring.  
Move the buttons and levers while the marine  
case is submerged, and rinse the salt out from  
any gaps or grooves etc.  
Never use an O-ring if it is deformed (crushed,  
distorted), cracked, or damaged in any way.  
2 Wipe off the water with a dry cloth, and  
allow the marine case to completely dry  
out.  
3 Open the marine case, and remove the  
camera.  
Lock  
Main Specifications  
Maximum  
Water depth up to 30 meters  
pressure  
Power on/off  
Video recording start/stop  
Still image shooting  
Remove  
Operations  
Zoom (telephoto/wide angle)  
4 Remove the O-ring, and wipe off any salt,  
+400 g (with the camera  
inserted and the supplied  
battery pack attached)  
sand, and any other debris.  
Buoyancy  
Also wipe the groove in which the O-ring was  
inserted, and the part of the marine case that  
was in contact with the O-ring, and allow them to  
dry.  
Main unit  
dimensions  
(W x D x H)  
233 mm x 172 mm x 132 mm  
5 Wipe the inside of the marine case with a  
Main unit weight Approx. 800 g (not incl. grip)  
dry cloth.  
Applicable model  
Base A: GZ-MG130 ~ 275  
and base to be  
Drop a few drops of the cleaning fluid onto the  
inside of the front glass, and wipe it off using the  
silicone cloth etc.  
Base B: GZ-MG555 ~ 575  
used  
Filter diameter  
ø 67.0 mm  
NOTES  
Do not leave the marine case in direct sunlight.  
Doing so may cause discoloration to the case, and  
may cause the O-ring to deteriorate more quickly.  
When storing the marine case, unlock the power/  
mode switch lever.  
If you cannot avoid opening the marine case at the  
diving point, make sure that drops of water from  
your hair or your body do not drop into the case.  
7
Printed in Japan  
0307FOH-AL-VP  
© 2007 Victor Company of Japan, Limited  
WR-MG88U  
Procedures for Using the Mukana toimitetun  
Supplied Maintenance  
Kit  
Vorgehensweise bei der  
Anwendung des  
mitgelieferten Wartungssets underhållsutrustningen  
Procédures pour  
l’utilisation de l’ensemble  
d’entretien fourni  
ENGLISH  
DEUTSCH  
FRANÇAIS  
NEDERLANDS  
CASTE.ESP.  
ITALIANO  
PORTUGUÊS  
DANSK  
huoltopakkauksen  
käytön menettelytavat  
Hur man använder den  
medföljande  
Prosedyrer for bruk av  
det medfølgende  
vedlikeholdssettet  
Procedures voor het  
Návod k používání sady  
gebruik van de bijgeleverde na údržbu  
onderhoudskit  
Procedury używania  
Procedimientos para utilizar dostarczonego zestawu  
el kit de mantenimiento  
suministrado  
Procedure per l’utilizzo  
del Kit di manutenzione  
in dotazione  
Procedimentos para a  
utilização do kit de  
manutenção fornecido  
Procedurer ved anvendelse  
af det medfølgende  
vedligeholdelsessæt  
do konserwacji  
A mellékelt szerelési  
készlet használata  
Порядок  
использования  
комплекта для ухода  
SUOMI  
SVENSKA  
NORSK  
ČEŠTINA  
POLSKI  
使用隨附之維修工具組的  
步驟  
附带维护用具的使用程序  
MAGYAR  
РУССКИЙ  
LYT1742-002A  
Procedures for Using the  
Strap (J Page 4)  
Pass the strap  
through the strap  
Silicon cloth  
Wash the marine  
case with fresh  
water, and wipe  
the outer side with  
the silicon cloth  
after drying.  
attachment hole  
before using the  
marine case to  
maintain a firm grip  
in water.  
Strap attachment hole  
Buckle opener  
(Hexagonal wrench (small))  
(J Page 5)  
Buckle  
Grip belt of camera  
For use when you have  
difficulty opening the buckle.  
Hook the wrench to the  
buckle and pull towards you.  
Silica gel  
(anti-fogging agent) (J Page 5)  
Prevents fogging  
inside the marine  
case.  
Buckle  
Insert it between  
the camera and the  
camera grip belt  
before inserting the camera into the  
marine case.  
Caution: The moisture absorption  
ability of silica gel that has previously  
been used may deteriorate depending  
on the conditions of use. As such, we  
recommend that the silica gel be  
replaced each time.  
2
Supplied Maintenance Kit  
Glass cleaner (J Page 4)  
(to prevent fogging)  
Apply the glass cleaner on the  
front glass before using the marine  
case.  
Add two to three drops of the  
cleaner on a lens tissue paper,  
and wipe the inner side of the front  
glass.  
Marine case  
Front glass  
Cleaner liquid (J Page 7)  
For removing dirt from the front  
glass after using the marine case.  
Add two to three drops of the  
cleaner on a lens tissue paper,  
and wipe the inner side of the front  
glass.  
Lens tissue paper (J Page 4)  
Use the lens tissue paper  
when applying the antifog  
liquid on or removing dirt  
from the front glass.  
Camera base  
Screw tightening key (J Page 5)  
Use the key to tighten  
the screw of the  
camera base.  
3
O-ring  
Rubber ring for waterproofing.  
Check to ensure that the ring is not twisted and foreign materials are not  
attached, followed by attaching it to the designated position.  
Dirt, sand, salt  
crystals, etc.  
Hair, thread, etc.  
O-ring  
Swab  
For cleaning the O-ring groove.  
Press it lightly against the O-ring groove and move it around the circumference  
of the groove.  
Swab  
4
Pick  
For removing the O-ring.  
To remove the O-ring, insert the pick between the O-ring and the O-ring  
groove.  
Pick  
O-ring  
O-ring groove  
Silicon grease  
For protecting the O-rings and preventing water leakage.  
Check to ensure that there is no foreign substance on the O-ring before  
applying the grease.  
Squeeze about 1 cm of the grease onto your finger, and apply it on the  
O-ring by holding the O-ring with your fingers.  
* Do not pull the O-ring with force.  
About 1 cm  
O-ring  
Grease  
Precautions  
O-ring is important as it keeps the marine case airtight. Failure to  
attach it correctly may cause water to enter the marine case and  
the camera inside to malfunction as a result. Pay careful attention  
when attaching the O-ring.  
5
After shooting (sea salt removal)  
Make sure to perform maintenance on the marine case.  
Salt crystal or dirt will accumulate inside the marine case if maintenance is not  
performed, and this may cause water leakage.  
A Prepare a container that contains fresh water that is five times more  
than the volume of the marine case.  
• If only small containers are available, pour in fresh water that is equivalent to at  
least five times the volume of the marine case over a few times, followed by  
performing salt removal in G.  
Example: Container with volume  
J Pour in water over 5 times  
equivalent to 1 marine case  
• The container must be big enough to allow the marine case to submerge fully.  
• Perform salt removal for the grip as well.  
B After diving, submerge the marine case in fresh water for 30 minutes  
without removing the camera.  
C Temporary salt removal  
Shake the marine case in the upward, downward, left and right  
directions for at least 10 times, followed by rinsing it.  
• If you do not need to take out the camera immediately, proceed to Gfor the  
actual salt removal.  
D Remove the marine case and wipe off water droplets on the case  
surface using a dry cloth.  
6
E Face the front glass of the marine case upwards, and open the  
buckles to remove the camera, while paying attention not to let water  
droplets at the O-ring or buckles enter the case.  
Front glass  
F Upon removing the camera, close the marine case again while paying  
attention not to allow water droplets enter the case, followed by  
tightening all the buckles.  
G Final salt removal  
Submerge the marine case in fresh water for at least 1 hour to  
remove salt.  
• Shaking the case body in the upward and downward directions and rinsing it  
helps to remove salt more effectively.  
• Make sure the marine case is fully submerged in the fresh water.  
H Remove the marine case and wipe off water droplets on the case  
surface using a dry cloth. Then open the buckles to allow the inside  
and outside of the case to dry thoroughly.  
Memo  
Temperature, humidity, water temperature, salinity and other conditions  
vary according to the environment of use.  
7
 
© 2007 Victor Company of Japan, Limited  
Printed in Japan  
0507MNH-SW-OT  

Pioneer Car Stereo System AVH P6400 User Manual
Pioneer AppRadio SPH DA01 User Manual
Philips LCD MONITOR 220VW8 User Manual
Pentax HS2V616ED (C60635) User Manual
Panasonic AJ HDC27A User Manual
Olympus Camera Lens VN595201 User Manual
Nikon AF S Nikkor User Manual
Kicker RESOLUTION RMB8 User Manual
Kenwood Car Stereo System TK 5720 User Manual
JVC KDS600 User Manual