HD MEMORY CARD CAMERA RECORDER
INSTRUCTIONS
GY-HM100U
The illustration shows the GY-HM100U
with the provided microphone attached.
4HANK YOU FOR PURCHASING THIS *6# PRODUCTꢀ "EFORE OPERATING THIS
DEVICEꢁ PLEASE READ THE INSTRUCTIONS CAREFULLY TO ENSURE THE
BEST POSSIBLE PERFORMANCEꢀ
For Customer Use:
%NTER BELOW THE 3ERIAL .Oꢀ WHICH IS LOCATED ON THE BODYꢀ
2ETAIN THIS INFORMATION FOR FUTURE REFERENCEꢀ
-ODEL .Oꢀ '9ꢂ(-ꢃꢄꢄ5
3ERIAL .Oꢀ
LYT2089-001D
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
Declaration of Conformity
Model Number : GY-HM100U
Trade Name : JVC
Responsible party : JVC AMERICAS CORP.
Address : 1700 Valley Road Wayne, N. J. 07470
Telephone Number : 973-317-5000
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
10. Only use attachments/accessories specified by the
manufacturer.
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not approved by
JVC could void the user’s authority to operate
the equipment. This equipment has been
tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures: Reorient or relocate
the receiving antenna. Increase the separation
between the equipment and receiver.
11. Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer, or
sold with the apparatus.
When a cart is used,
use caution when
moving the cart/
apparatus combination
to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or
when unused for long periods of time.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/
TV technician for help.
If this symbol is shown, it is only valid in
the European Union.
AC adapter
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
When using the AC adapter in areas other than
the USA
The provided AC adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to
an AC wall outlet other than American National
Standard C73 series type use an AC plug adapter,
called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest
JVC dealer.
Plug Adapter
3
Getting Started
Ⅵ Full Auto shooting mode
Main Features
Eliminates the need for troublesome switch operations by
automatically providing a wide range of compatibility with
shooting conditions that change as you move between
indoors and outdoors or between bright and dark
locations.
Ⅵ Image Stabilizer feature
This camcorder enables recording of HD format images as
videos or still pictures on an SD card, and also playback of
these videos or still pictures.
Reduces blurring of images due to camera shake.
Ⅵ ND filters provided
Ⅵ Program AE function
Ⅵ Supports various HD video recording formats
(1080i, 1080p, and 720p)
Enables selection of shooting conditions according to the
scenes of your preference.
Shooting can be performed in different HD recording
modes, thus supporting a wide variety of content
production.
Ⅵ White balance adjustment feature
Enables white balance to be adjusted automatically or
manually.
Ⅵ QuickTime(MOV)/MP4 format for video files
Enables direct recording in the QuickTime file format used
by Apple Inc.’s Final Cut Pro. The recorded clips can be
edited directly using Final Cut Pro. In addition, the support
for MP4 file format enables the video files to be used
widely in different environments.
Ⅵ Built-in color bars (multi-format color bars)
Ⅵ Slow shutter
Makes it possible to brightly shoot video of dark subjects
with little motion by accumulating the images.
Ⅵ SD card recording
Ⅵ Three audio input terminals
This camcorder comes with two SD card slots, and
enables continuous recording to two SD cards by
switching automatically between the slots. In addition,
recorded files can also be moved or copied between the
two SD cards. However, video files can only be copied.
This camcorder comes with two XLR terminals and one
mini-jack terminal, which can be used as audio input
terminals for the built-in or external microphone.
Ⅵ Three video output terminals
This camcorder comes with an HDMI terminal, a
component terminal, and an A/V OUT (video/audio
output) terminal, which support a wide variety of TV
monitor types.
Ⅵ Supports both video recording and still picture
recording modes
You can select a mode from video recording and still
picture recording. During playback of a file, you can select
a video or still picture from the thumbnail display on the
index screen or date search screen.
Ⅵ Connection to PCs via USB port
Video or still picture files stored on an SD card can be
retrieved to a PC.
Ⅵ Supports 60 Hz/50 Hz HD signals
Ⅵ Focus Assist function
Ⅵ Saving and loading of setting files
The current menu and camcorder settings can be saved
to an SD card. (Up to four files) In addition, settings files
stored on the SD card can also be loaded onto the
camcorder according to the shooting scene to reproduce
the most suitable settings.
Enables easy and accurate focusing during shooting.
Ⅵ User buttons added
Enables you to switch camera settings instantly to suit the
shooting conditions.
Ⅵ Time code reader/generator
The built-in time code reader/generator can be used to
record and play back the time code and user’s bit.
Ⅵ Built-in viewfinder and color LCD display
Displays the status screens, menu screens for settings,
and alarm indications, in addition to the camera image
and playback image.
Ⅵ Built-in monitor speaker for audio checking
Ⅵ Recording check function for convenient
recording review
Ⅵ Camera designed with 3-CCD system for high-
quality picture
Ⅵ Zebra pattern video level indication
4
Shooting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Contents
Using the Camcorder in the Still Picture
Setting the Picture Quality, Recording Size,
Adjusting the Focus Manually . . . . . . . . . . . . . . . . . . . . .31
Using the Focus Assist Function . . . . . . . . . . . . . . . . .31
Indications on the LCD Screen and in the Viewfinder . . .15
Displaying the Status Screen . . . . . . . . . . . . . . . . . . . .15
Shooting Different Scenes and Conditions
Displaying the Zebra Pattern . . . . . . . . . . . . . . . . . . . . . .34
Displaying the Zebra Pattern . . . . . . . . . . . . . . . . . . . .34
Items Displayed During Video and
Specifying the Luminance Level Range for
Items Displayed During Still Picture Shooting Only . . .17
Setting the Reference Audio Recording Level . . . . . . .40
Inserting an SD Card . . . . . . . . . . . . . . . . . . . . . . . . . .23
Using an External Microphone Connected to the
MIC Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Using an External Microphone Connected to the
Displaying the Time Code/User’s Bit . . . . . . . . . . . . . .41
Setting the Video Format . . . . . . . . . . . . . . . . . . . . . . .26
Displaying the Remaining Space on the SD Card . . . .27
Shooting Videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Playing Back Videos from the Playback
Capturing a Still Picture in the Still Mode . . . . . . . . . . .46
Enlarging a Still Image . . . . . . . . . . . . . . . . . . . . . . . . .47
Adjusting the Volume of the Built-In Speaker
or Headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
5
Getting Started
How to use this manual
Contents (continued)
:
Describes precautions concerning the
operation of this product.
Caution
:
Describes reference information, such as
functions and usage restrictions of this
product.
Viewing Still Picture File Information . . . . . . . . . . . . . .49
:
Indicates the reference page numbers and
reference items.
reprinting of this manual, in whole or in part, is strictly
prohibited.
● All other product names used in this manual are
trademarks or registered trademarks of their respective
companies. Marks such as ™, ா and have been
omitted in this manual.
Copying/Moving Files . . . . . . . . . . . . . . . . . . . . . . . . . . .52
● Illustrated designs, specifications and other contents of
this manual are subject to changes for improvement
without prior notice.
Remember that this camcorder is intended for
private consumer use only.
Any commercial use without proper permission
Operation Sound and Tally Settings . . . . . . . . . . . . . . . .56
HDMI is a trademark of HDMI
Licensing, LLC.
We recommend using the Category 2 HDMI cable
(High Speed cable) for viewing in higher image quality.
QuickTime and Final Cut Pro are trademarks of
Apple Inc.
Other product and company names included in
this instruction manual are trademarks and/or
registered trademarks of their respective holders.
Menu Screens of the Video Shooting Mode . . . . . . . . . .59
Others
Estimated Number of Still Picture Shots . . . . . . . . . . .73
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Dimensional Outline Drawing . . . . . . . . . . . . . . . . . . . .75
6
Audio Unit
Accessories
Clamp
Screw
Cable
Shoe
This camcorder comes bundled with the following
accessories.
AC Adapter
AP-V21M
Battery
BN-VF823U
Battery Charger
AA-VF8KR
Remote
Control Unit
Open the cover
AUDIO IN Terminal
SD Cards
Component Cable AV Cord
Power Cord
USB Cable
ן 2 This camcorder saves the recorded images and audio sound
on the SD card (sold separately) in the card slot.
Microphone
Audio Unit
CD-ROM
Memo :
● If the SD card contains files recorded by devices other than
this camcorder or files that are saved from a PC, the
recordable time may be shorter or data may not be
properly recorded. In addition, the remaining space on the
card may not increase even when files are deleted using a
PC.
Make use of the following SD cards.
The CD-ROM provided with this camcorder comes with
[JVC ProHD Clip Manager] and other application software
as well as the user guides.
Video
: SDHC card that supports Class 6 or higher
(4 GB to 32 GB)
Still Picture : SD card (256 MB to 2 GB), SDHC card (4 GB
TFor detail, refer to the user guides for each application
software.
to 32 GB)
● Panasonic, TOSHIBA, or SanDisk
Using cards other than those specified above may prevent
data from being recorded correctly or result in loss of
data.
Attaching the Audio Unit
The audio unit (with handle) is not attached to the camcorder
unit when purchased.
Attach the audio unit according to the following procedure.
1 . Attach the audio unit by sliding it all the way into
the shoe on the top of the camcorder.
2 . Turn the screw on the audio unit clockwise to fasten
it fully and securely to the camcorder.
TIf the audio unit is not fully and securely tightened, it will be
loose and may drop off from the camcorder during use.
3 . Connect the audio unit cable to the AUDIO IN
terminal of the camcorder.
Memo :
● The clamp on the audio unit is for fixing the microphone
cable and cannot be used to fix the audio unit cable.
(A Page 18)
7
Getting Started
Ⅵ Do not turn off the [POWER] switch or remove
the power cord during recording or playback.
Precautions for Proper Use
Ⅵ The camera may not show stable pictures for a
few seconds immediately after the power is
turned on, but this is not a malfunction.
Ⅵ Do not turn off the [POWER] switch when the
camera reboots due to the following operations.
● Rebooting when the video/still picture mode is switched while
the [SYSTEM SELECT] menu is set to [720-**]
● Rebooting when the [SYSTEM SELECT] menu is set
● Rebooting after a setting file stored on the SD card is loaded
● Rebooting when the [SYSTEM SELECT] menu is changed
Ⅵ Allowable ambient temperature and humidity
Be sure to use this device within the allowable temperature range
of 0°C to 40°C and a relative humidity of 35 % to 80 %. Using this
device at a temperature or humidity outside the allowable ranges
could result not only in malfunction but the impact on the CCD
elements could be serious as small white spots may be generated.
with the default value settings
Ⅵ Strong electromagnetic waves or magnetism
Noise may appear in the picture or audio and/or the colors may
be incorrect if the camera is used near a radio or television
transmitting antenna, in places where strong magnetic fields are
generated by transformers, motors, etc., or near devices emitting
radio waves, such as transceivers or cellular phones.
Ⅵ Use the supplied AC adapter as the power
supply. Do not use the supplied AC adapter on
other devices.
Ⅵ When the connectors that come with connector
covers are not in use, put on the covers to
prevent damage to the connectors.
Ⅵ Use of wireless microphone near the camera
When a wireless microphone or wireless microphone tuner is used
near the camera during recording, the tuner could pick up noise.
Ⅵ When this device is not in use, be sure to set the
[POWER] switch to AOFFB in order to reduce
power consumption.
Ⅵ Avoid using or placing this device in the
following places.
● Places subject to extreme heat or cold
● Places with excessive dirt or dust
● Places with high humidity or moisture
● Places subject to smoke or vapor such as near a cooking stove
● Places subject to strong vibrations or unstable surfaces
● In a parked car under direct sunlight or near a heater for long
hours
● Places subject to radiation or X-rays, or where corrosive gases
Ⅵ Wipe the external cabinet of the device with a
soft cloth. Do not wipe the body with benzene or
thinner. Doing so may cause the surface to melt
or turn cloudy. When it is extremely dirty, soak
the cloth in a solution of neutral detergent, wipe
the body with it, and then use a clean cloth to
remove the detergent.
occur
Ⅵ
Protect this device from being splashed with water.
(Especially when shooting in the rain)
LCD Screen and Viewfinder
Ⅵ The LCD and viewfinder screens are
manufactured using high-precision technology.
Black spots may appear on the LCD and
viewfinder screens, or red, blue, and/or white
spots may not turn off. However, this is not a
malfunction and these spots are not recorded
on the SD card.
Ⅵ Protect this device from getting wet when
shooting on a beach. In addition, salt and sand
may adhere to the camera body. Be sure to clean
the camera after use.
Ⅵ Protect this device against penetration of dust
when using it in a place subject to sandy dust.
Ⅵ Do not expose this device and the remote
control to excessive heat, such as direct
sunlight or fire. The built-in battery may explode
if it gets heated up.
Ⅵ If you use this device continuously for a long
period of time, the characters displayed in the
viewfinder may temporarily remain on the
screen. This is not recorded on the SD card.
They will not appear after you turn the power off
and then on again.
Ⅵ Optical performance of lens
Due to the optical performance of the lens, color divergence
phenomena (magnification chromatic aberration) may occur. This
is not a camera malfunction.
Ⅵ If you use this device in a cold place, the images
may appear to lag on the screen, but this is not a
malfunction. This is not recorded on the SD
card.
Ⅵ
Noise may appear in the image when switching
between the playback picture and the EE picture.
Ⅵ If placed on its side, heat release efficiency will
Ⅵ Do not press against the surface with force or
subject it to strong impact. Doing so may
damage or break the screens.
deteriorate.
Ⅵ Precautions for transportation
● When carrying the camcorder, be sure to hold the carrying
handle. Holding the lens or viewfinder may result in damage.
● Do not drop or hit this device against a hard object.
Handling of SD Cards
Ⅵ The access lamp blinks when data on the SD
card is being accessed (recording, playback,
formatting, etc.). Do not remove the SD card,
turn off the power, or remove the battery/AC
adapter during access.
Ⅵ Do not insert objects other than the memory
card into the card slot.
Ⅵ Do not leave the card slot cover open for a long
period of time. Dirt entering the interior of the
slot may cause it to malfunction.
8
Ⅵ If the SD card is removed while data is being
accessed, the request for recovery screen may
appear repeatedly even if execution is selected.
When this happens, format the SD card. All data
will be deleted.
Ⅵ Attach the battery cap after removing the
battery, and store it in a dry place between 15°C
to 25°C.
Battery
Ⅵ Do not use or store this device in a place that is
subject to static electricity or electrical noise.
Ⅵ Inserting the SD card incorrectly may result in
Battery Cap
damage of this device or the SD card.
Ⅵ We are not liable for any accidental loss of data
stored on the SD card. (Please back up any
important data.)
Ⅵ ATTENTION:
The product you have purchased is powered by
a rechargeable battery that is recyclable.
Please call 1-800-8-BATTERY for information on
how to recycle this battery.
Ⅵ Make use of the SD card within the prescribed
conditions of use.
Do not use the SD card in places that are subject to direct
sunlight, high humidity or corrosion, places near thermal
equipment, or in a car under the sun with the doors and windows
closed.
Characteristic CCD Phenomena
Ⅵ Do not bend or drop the SD card, or subject it to
Smear and blooming
strong impact or vibration.
When shooting an extremely bright light source, vertical
streaking (called "smear") may occur or expansion of light
(called "blooming") may appear around it. This is a
characteristic of the CCD and not a malfunction.
Ⅵ Do not splash the SD card with water.
Ⅵ Do not place the SD card near locations that are
exposed to strong magnetic fields or radio
waves.
Smear
Vertical pale streaking appearing at
high luminous object
High luminous object
Ⅵ Do not touch the metal parts.
Ⅵ If you want to wipe out all information by
completely erasing the data, we recommend
either using commercially available software
that is specially designed for that purpose, or by
physically destroying the SD card with a
hammer, etc. When formatting or erasing data
using the camera, only the file administration
information is changed. The data is not
completely erased from the SD card.
(Electric light, sunlight, etc.)
Blooming
Blurring in highlight
Monitor Screen
Moire or aliasing
Stripes, lines or other fine patterns may appear jagged
when they are shot.
White dots
High temperatures can cause CCD sensor pixels to
produce white dots in the image. This condition is
conspicuous especially when gain is applied.
This is a characteristic of the charged-coupled device
(CCD). As far as possible, use this device under conditions
where the temperature of this device does not increase.
Rechargeable Battery
Ⅵ Be sure to use only JVC batteries.
We do not guarantee the safety and performance
of this device if a battery other than a JVC
product is used.
Ⅵ The battery is not charged when purchased.
Characteristic Lens Phenomena
Ⅵ When using the battery in a low temperature
environment (10°C or below), the operating time
may be shortened, or it may not function
When shooting an extremely bright light source, ghosting
may occur. This is a characteristic of the lens and not a
malfunction.
properly. When using the device outdoors in the
winter weather, warm the battery, such as by
placing it in the pocket, before attaching it.
Copyright
Ⅵ Do not expose the battery to excessive heat,
such as direct sunlight or fire.
Any recordings made on this camcorder that are played back
for profit or public preview may infringe on the rights of the
owner of the recordings.
Do not use the recordings for purpose other than personal
enjoyment without prior consent from the owner.
Ⅵ If the battery is not to be used for a long time,
A use up the charge completely and detach it from the
camera to prevent deterioration. (Wait for the battery
to run out by itself such as through continuous
shooting or playback.)
B charge the battery once every half a year, and store it
again after using up the charge.
9
Getting Started
Names of Parts and
Functions
Front
Top
Q
d
c
b
a
Z
T
W
AWB
R S
T
U
V
W
X Y
Front
Top
A Tally lamp (A Page 56)
F Shoe
For mounting separately sold accessories.
B Tally lamp (A Page 56)
G Eyepiece focus lever
D [AWB] Auto White Balance button (A Page 35)
side.
For adjusting the white balance.
H Eyepiece
E Lens/Lens cover (A Page 20)
J [SNAPSHOT] Snapshot button (A Page 29)
K Zoom lever (A Page 30)
For zooming to the Tele (T) or Wide (W) end.
L Microphone holder (A Page 18)
For mounting an external microphone.
M Knob
Knob for locking the microphone in place.
N External microphone (A Page 18)
10
LCD Side
j i h
AUTO MANUAL
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
-
LINE
MIC
-
AUDIO
INPUT1
-
-
SELECT
INPUT2
MIC+48V
g
INPUT1
INPUT2
AUTO MANUAL
f
e
Q
R
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
d
c
b
OFF
AF/MF
FULL AUTO
GAIN WHT.BAL
A / B
L-
B-
M-
H-
A-
PRST-
A
B
Z a
A Built-in microphone (A Page 40)
B Lens cover switch (A Page 20)
A specific feature in the menu setting can be assigned to
this button according to the user’s preference.
P [USER1] User 1 button (A Page 21)
D [ND FILTER] switch (A Page 32)
this button according to the user’s preference.
Reduces the amount of incident light to 1/10.
E [GAIN] switch (A Page 37)
Q [CH-1/CH-2 AUDIO LEVEL] CH-1/CH-2 recording level
adjustment knob (A Page 40)
For selecting one of the three sensitivity levels.
audio.
For selecting one of the three types of white balance.
R [CH-1/CH-2 AUDIO SELECT] CH-1/CH-2 audio selection
switch (A Page 40)
G [A/B] Card slot A/B selection button (A Page 23)
H Card slot A access lamp (A Page 23)
For setting the method of adjusting the audio recording
level for the CH-1 or CH-2 audio to the Auto or Manual
mode.
Slot for SD cards.
Open the door to insert the SD card.
S [INPUT1/INPUT2 AUDIO INPUT] INPUT1/INPUT2 audio
input signal selection switch (A Page 40)
terminal.
J Card slot B (A Page 23)
Slot for SD cards.
T [CH-2 INPUT] CH-2 audio input terminal selection switch
(A Page 40)
K Card slot B access lamp (A Page 23)
L [FULL AUTO] Full Auto mode selection button
For selecting whether to input audio signals to CH-2
audio from the INPUT1 or INPUT2 terminal.
(A Page 25)
For setting the shooting mode to the Full Auto or Manual
mode.
Memo :
● INPUT1 terminal, INPUT2 terminal: R, S on Page 13
M [AF/MF] Focusing mode selection button (A Page 26)
For setting the focusing mode to the Auto or Manual
mode.
N [FOCUS/ZOOM] ring switch
For setting the function of the manual ring to focus
(A Page 31) or zoom adjustment (A Page 30).
11
Getting Started
Names of Parts and
Functions (continued)
LCD Side (LCD Cover)
When the LCD cover is opened
Y
X
W
V
U c
b
a
INDEX
T
CAM / MEDIA
MENU
USER3
P
RO
G
R
A
M
E A
DISPLAY
Q.REVIEW
W
T
COMPONENT
OUT
A / V OUT
REC
AUTO MANUAL
2
3
4
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
5
-
LINE
MIC
-
-
AUDIO
SELECT
INPUT1
-
INPUT2
MIC+48V
0
1
2
I
N
P
U
T
1
I
N
P
U
T
2
3
AUTO MANUAL
Q
R
S
Z
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
OFF
AF/MF
FULL AUTO
Bottom
d
GAIN WHT.BAL
A
/
B
L-
B-
M-
H-
A-
P
R
S
T
-
A
B
A LCD cover
L [INDEX] Index button
(A Page 49)
Displays the remaining space on the SD card
(A Page 20).
C [A/V OUT] Audio/Video output terminal (A Page 49)
For checking the video image immediately before
shooting starts.
When in the playback mode, pressing this button
switches between the playback index and date search
screens. (A Page 45)
Displays the menu screen. Press this button again to exit
the menu screen.
M Set Lever
When in the shooting mode, this lever is used for
Program AE selection and as the zooming lever.
(A Page 32)
When in the playback mode, this lever is used for
playback file selection and playback control. (A Page 43)
menu setting. (A Page 57)
F Built-in speaker (A Page 47)
G [CAM/MEDIA] Camera shooting/media playback
selection button (A Page 25)
For setting this camcorder to the Camera Shooting or
Media Playback mode.
Bottom
H [USER3] User 3 button (A Page 21)
A specific feature in the menu setting can be assigned to
N Tripod mounting holes (A Page 18)
● To prevent the camcorder from falling, attach securely
using the rotation prevention hole.
I [DISPLAY] Display button
viewfinder. (A Page 15)
● Use screws with screw length 5 mm and below.
the file information.
(A Page 46)
J [REC] Video recording button (A Page 27)
Button for starting or stopping video recording.
12
i
h
Rear
Grip Belt Side
c
b
ACCESS
IRIS
a
Q
R
SHUTTER
OPEN
AE
±
REC
CLOSE
DC
ST
U V W X
Y
Z
d e
e fg
Rear
Grip Belt Side
A [IRIS] Aperture button (A Page 37)
N [POWER/MODE] Power/Operating mode switch
POWER : Turns the power On/Off. (A Page 20)
picture mode. (A Page 25)
B [SHUTTER] Shutter Speed button (A Page 37)
Press this button to set the shutter speed manually.
O Grip belt mount (A Page 18)
C [AE ] Exposure button (A Page 33)
Q [MIC] Microphone input terminal (A Page 40)
D [ADJ./VOL.] Adjustment/Volume knob
For connecting a mini-jack microphone.
speed (A Page 37), and exposure (A Page 33).
● The MIC terminal provides a 4 V power supply to the
microphone.
R [INPUT1] Audio input 1 terminal (A Page 40)
E Battery mount (A Page 19)
For connecting an XLR microphone.
F [HDMI] terminal (A Page 49)
G [USB (2) ] terminal (A Page 54)
H [DC] input terminal (A Page 19)
S [INPUT2] Audio input 2 terminal (A Page 40)
For connecting an XLR microphone.
J [REC] Video recording button (A Page 27)
For starting or stopping video recording.
Lights up during still picture shooting or still picture
playback mode.
L Video indicating lamp (A Page 25)
Lights up during video shooting or video playback mode.
M [ACCESS] Charging/Access indicating lamp
Lights up or blinks during recording or playback.
Blinks when the battery is charging. (Light goes out when
charging is complete.)
13
Getting Started
Names of Remote Control
Parts and Functions
Q
e
SET
c
R
f
a
S
T
Z
b
d
SET
Y
X
U
V
W
A [START/STOP] button
K [INFO] button
Button for starting or stopping video recording.
When in the playback mode, pressing this button displays
the file information.
B [ZOOM] button
Press (T) to zoom in.
Press (W) to zoom out.
Playback zoom can be used when a video is paused or
L [ ] Left button
Moves the cursor to the left on the menu screen or
playback index screen.
during playback of still images.
It is also used to perform reverse search during playback.
C [S.SHOT] SNAPSHOT button
M [ ] Down button
Button for starting the recording of still images.
Moves the cursor downward on the menu screen or
playback index screen.
D [–] button
Moves to the previous date when the playback index
screen is displayed.
N [ ] Right button
Moves the cursor to the right on the menu screen or
playback index screen.
It is also used to perform forward search during playback.
E [N] Reverse button
Returns to the beginning of the file during playback.
O [ ] Up button
F [PLAYLIST] button
Moves the cursor upward on the menu screen or
playback index screen.
This function is not available on this camcorder.
G [DISP] DISPLAY button
For switching the displays on the LCD screen and
viewfinder.
P [SET] button
For confirming a selected item on the menu screen or
playback index screen.
H [INDEX] button
It is also used to start or stop playback when in the
playback mode.
Displays the remaining space on the SD card and the
remaining battery power.
The Left, Right, Up, and Down buttons can be used to shift
the zoom position when a still image is enlarged using the
ZOOM button.
When in the playback mode, pressing this button
switches between the playback index and date search
screens.
I [O] Forward button
Memo :
● To use the remote control, set [REMOTE] in the [CAMERA
SETTINGS] menu to [ON]. (A Page 66)
Advances to the next file during playback.
J [+] button
Moves to the next date when the playback index screen is
displayed.
14
Ⅵ When in the video playback or still picture
playback mode
Indications on the LCD
Screen and in the Viewfinder
Select the details to display using the settings in the [ON-
SCREEN DISPLAY] menu.
ASetting Menu ScreensB: (A Page 57)
OFF
:
:
No display.
The status screen can be displayed on the LCD screen or
DISPLAY ALL
Displays all icons and the date and time.
viewfinder.
DISPLAY DATE
ONLY
Status screen is a screen display for identifying the current
settings.
:
:
Displays only the date and time.
DISPLAY DATE
5 SEC
Displays only the date and time for 5
seconds in the following cases:
Displaying the Status Screen
● When playback starts
● When a file is changed during playback
● When the menu screen is closed
Ⅵ When in the video shooting or still picture
shooting mode
Pressing the DISPLAY button each time toggles the display
as follows:
During video playback, pressing the DISPLAY button each
time toggles the display as follows:
[DISPLAY DATE ONLY]B[DISPLAY ALL]B[OFF]
“Main information for camera shooting” B “Full display” B
“Simple display”
DISPLAY
DISPLAY
Main information for camera shooting
DISPLAY DATE ONLY
[
]
A
B
1h56m
[
]
1h56m
0
00:00:00:00
F5.6
1/4000
18dB
CH1
CH2
4 : 5 0 P M
NOV.1.2009
DISPLAY
Full display
[
]
A
B
1h56m
[
]
DISPLAY ALL
DISPLAY
1h56m
0
00:00:00:00
+
1
F5.6
1/4000
18dB
ND
10x
A
005/600
00:00:00:00
3200K
SPORT
4 : 5 0 P M
CH1
CH2
NOV.1.2009
4 : 5 0 P M
Simple display
DISPLAY
N OV. 1 . 2 0 0 9
DISPLAY
OFF
Appears when the remaining
time falls below 2 minutes
The diagrams above are displays in the video shooting
mode.
Memo :
DISPLAY button
● When in the still mode or when the index screen is
displayed, pressing the DISPLAY button displays the file
information.
CAM MEDIA
/
USERS
DISPLAY
Q.REVIEW
MENU
● To display this screen on the monitor that is connected to
the video output terminal of this camcorder, set [DISPLAY
ON TV] in the [CONNECTION SETTINGS] menu to [ON].
COMPONENT
OUT
A
/ V OUT
15
Q Card Slot
: The selected card slot is indicated by the card icon
as shown on the left.
R Automatic Slot Switch
Screen and in the
Viewfinder (continued)
Displayed when [SLOT AUTO SWITCHING] in the
[CAMERA SETTINGS] menu is set to [ON].
S Tele Macro
Displayed when [TELE MACRO] in the [CAMERA
PROCESS] menu is set to [ON].
Items Displayed During Video and Still
Picture Shooting
Q
i
h
Items Displayed During Video Shooting
A
B
R
S
T
U
V
W
X
Y
Z
g
Only
0
b a
Y X
Z
F5.6
1/4000
10x
f
e
[
]
1h56m
Q
R
S
ND
[
]
1h56m
W
d
3200K
SPORT
00:00:00:00
c
V
4 : 5 0 PM
NOV.1.2 0 0 9
CH1
CH2
b
a
U
18dB
T
A Shooting Mode
A
M
: Full Auto Shooting
: Manual Shooting
B Focusing Mode
AF : Auto Focus
MF : Manual Focus
A Video Mode
B Sensitivity
C Wind Noise
C Exposure
Displayed when the [WIND CUT] menu is set to [ON].
D Simultaneous Still Picture Recording
E Continuous Clip Recording
L
: Fixed
D Aperture
E Shutter Speed
Displayed when the [CLIP CONTINUOUS REC] menu is
set to [ON].
F ND Filter
Displayed when the ND filter switch is set to AONB.
F Mode Indicator
G White Balance Color Temperature
RREC : Recording
H Program AE
PORT : Portrait
SPORT : Sports
SNOW : Snow
SPOT.L : Spotlight
TWIL. : Night
RW : Record Standby mode (Record Pause mode)
G Time Code or User’s Bit
TC : Time Code
UB : User’s Bit
The framing mode display for the time code is as follows:
00:00:00:00
I Image Stabilizer [OFF]
Colon (:) for non-drop frames
Displayed when [OIS] in the [CAMERA SETTINGS] menu
Dot (.) for drop frames
is set to [OFF].
H Remaining Time on the SD Card
J LCD Screen Backlight
I Video Picture Quality
SP : Standard
Displayed when [MONITOR BACKLIGHT] in the
[DISPLAY SETTINGS] menu is set to [ON].
HQ : High
K Microphone Input Level
J Frame Rate
L Date/Time
K Vertical Resolution
L Horizontal Resolution
M Battery
Blinks in red when the battery runs out.
The color of the icons in I, J, K and L changes
according to the settings in the [FILE FORMAT] menu.
N Focus Assist
Displayed when [FOCUS ASSIST] in the [CAMERA
PROCESS] menu is set to [ON].
When set to [QuickTime file format] : Displays in blue.
When set to [MP4 file format]
: Displays in orange.
O Speaker/Headphone Volume (displayed during volume
adjustment)
P Zoom
16
The framing mode display for the time code is as follows:
Items Displayed During Still Picture
00:00:00:00
Colon (:) for non-drop frames
Dot (.) for drop frames
Shooting Only
X
W V
F Current File Number/Total Number of Files
G Mode
[
[
]
]
Q
9999
9999
I
W
N
O
WI
HW
: Playback
: Still
: Forward Search
: Reverse Search
: Forward Slow
: Reverse Slow
U
T
R
S
10
The value on the left indicates the speed step.
H Card Slot
I Automatic Slot Switch
A Still Picture Mode
Displayed when [SLOT AUTO SWITCHING] in the
[CAMERA SETTINGS] menu is set to [ON].
B Focus Icon
Blinks in yellow: Focusing in progress
Lights in green: Focusing completed
J Video Picture Quality
SP : Standard
HQ : High
C Self-Timer
: 10-second self-timer
: 2-second self-timer
D Still Picture Recording
K Frame Rate
L Vertical Resolution
M Horizontal Resolution
E Shutter Mode
The color of the icons in J, K, L and M changes
according to the settings in the [FILE FORMAT] menu.
: Continuous Shooting
: Bracket Shooting
When set to [QuickTime file format] : Displays in blue.
F Remaining Number of Shots on the SD Card
When set to [MP4 file format]
: Displays in orange.
G Still Picture Quality
FINE : High
Items Displayed During Still Picture
Playback
STD : Standard
H Still Picture Size
W V
Items Displayed During Video Playback
Q
101-0098
U
T
c b a Z Y X
W
+
Q
1
A
005/600
V
U
00:00:00:00
S
R
4 : 5 0 P M
N OV. 1.2 0 0 9
T
S
R
A Still Picture Mode
B Date/Time
C Battery
4 : 5 0 P M
N OV. 1.2 0 0 9
A Video Mode
B Date/Time
C Battery
Blinks in red when the battery runs out.
D Slideshow (Blinks during playback)
E Current File’s Folder Number and File Number
F Card Slot
Blinks in red when the battery runs out.
D Speaker/Headphone Volume (displayed during volume
adjustment)
G Automatic Slot Switch
Displayed when [SLOT AUTO SWITCHING] in the
[CAMERA SETTINGS] menu is set to [ON].
E Time Code or User’s Bit
TC : Time Code
UB : User’s Bit
17
Preparations
Settings and Adjustments
Before Use
Attaching an External Microphone
You can attach a microphone to the microphone holder.
The supplied microphone is a phantom microphone.
1 . Turn the knob on the microphone holder
anticlockwise to loosen it and open the microphone
holder.
Adjusting the Grip Belt
2 . Place the microphone in the microphone holder.
Open the pad and adjust the position of the grip belt accordingly.
3 . Turn the knob on the microphone holder clockwise
to secure the microphone.
4 . Connect the microphone to the INPUT1/INPUT2
audio input terminal, or the MIC terminal according to
the type of microphone cable terminal you are using.
INPUT1/INPUT2 Terminal: XLR Terminal
MIC Terminal
: Mini-jack Terminal (stereo)
5 . Attach the microphone cable to the clamp.
Caution :
● If the grip is loose, the camcorder may fall off resulting in
injuries or malfunction.
6 . Specify the audio input settings correctly.
(A Page 40)
● Parents should take extra care when your child is using the
camcorder.
2. Microphone
1.3. Knob
5. Clamp
Setting up the Remote Control
The remote control comes supplied with batteries when you
purchase this product.
To start using, pull out the insulation sheet.
Insulation Sheet
Microphone Holder
4. INPUT1/
INPUT2 Terminals
AUDIO IN
Terminal
IO IN
UD
A
N
PE
O
4. MIC Terminal
AWB
Remote Control Sensor
Memo :
● When the audio unit cable is connected to the AUDIO IN
terminal of the camcorder, the MIC terminal is disabled.
Memo :
● To use the remote control, set [REMOTE] in the [CAMERA
SETTINGS] menu to [ON].
● Point the front end of the remote control toward the sensor.
Use the remote control within a distance of 5 meters from
the camcorder. The camcorder may not respond to the
remote control operations at some angles.
Attaching the Tripod
To prevent the camcorder from falling off, which may result in
injuries or damages, read the instruction manual of the tripod
to be used and make sure that it is securely attached.
(A Page 12)
Ⅵ Replacing batteries
1 . Press the lock tab, and pull out the battery holder.
Caution :
● Use the tripod on a stable surface.
2 . Replace the button battery (CR2025).
Lock Tab
Button Battery
18
Charging the Battery with this Camcorder
1. Turn off the power of the camcorder.
2 . Attach the supplied battery.
Removing the Hood
Remove the hood when attaching a filter (with external
diameter 50 mm and below), teleconverter or wide converter
to the front of the lens.
With the battery mark (D) on the left, insert it into the
Ⅵ Turn the hood in an anti-clockwise direction to
camcorder, and slide it to the left.
remove it.
3 . Connect the AC adapter that is provided with the
camcorder.
Connect the DC cable to the DC terminal, and the AC
adapter to a power outlet using the provided power cord.
● When battery charging starts, the access indicating
lamp blinks.
● When charging is complete, the access indicating lamp
goes out.
Hood
Access Indicating Lamp
Battery Lock
Release Button
Charging the Battery
There are two ways to charge the battery.
Ⅵ Charging with the supplied battery charger.
Ⅵ Charging with this camcorder.
N
I
IO
D
AU
OPEN
MIC
Charging the Battery with the Supplied
Charger
DC Terminal
Power Cord
Battery
1 . Connect the battery charger to a power outlet using
the provided power cord.
AC Adapter
To Power Outlet
Charging time and continuous recording time (approximate)
2 . Attach the supplied battery to the battery charger
by pressing and sliding it in the direction of the
arrow.
● When battery charging starts, the indicating lamp
blinks.
Battery
Continuous
Recording Time
Charging Time
● When charging is complete, the indicating lamp lights
up.
BN-VF815U
Approx. 2 hrs 40 Approx. 1 hr 25
mins mins
BN-VF823U
(Provided)
Approx. 3 hrs 40 Approx. 2 hrs 10
mins mins
3 . Remove the battery by sliding it in the opposite
direction after charging is complete.
To Power Outlet
● The above are the approximate charging times when
used under an ambient temperature range of 10°C to
35°C.
Battery
● A longer charging time may be required if the battery has
been left unused for a long time.
Power Cord
Indicating Lamp
● Recording time may differ depending on the age of the
battery, charging condition, and operating environment.
Battery
Charger
● Recording time is shortened in cold environments.
● Recording time is shortened when the zoom lens and
LCD screen are frequently used.
Ⅵ Removing the battery
1 . Turn off the power of the camcorder.
2 . Press the battery lock release button and slide the
battery to the right.
19
Preparations
Settings and Adjustments
Before Use (continued)
Turning On the Power
Preparation: Attach a charged battery or connect the AC
adapter.
1 . Set the POWER/MODE switch to ON.
POWER/MODE Switch
Checking the Remaining Battery Power
Preparation: Attach the battery.
1 . Press INDEX.
● The remaining battery power and recordable time are
displayed for about 3 seconds.
INDEX
To display the information for about 15 seconds, press
INDEX for 2 seconds or longer.
●The camcorder turns on in the video shooting mode.
BATTERY CONDITION
Ⅵ Turning off the power
1 . Set the POWER/MODE switch to OFF.
MAX TIME
min
Ⅵ Auto Power Off feature
When [AUTO POWER OFF] in the [CAMERA SETTINGS]
menu is set to [ON], the power turns off automatically when it
is not operated for 5 minutes or longer.
INDEX
Lens Cover
INDEX
Before shooting, open the lens cover.
When this camcorder is not in use, close the lens cover to
protect the lens.
IRIS
INDEX
SHUTTER
T
AE
±
REC
W
REC
Ⅵ Use the lens cover switch to open or close the lens cover.
DC
Memo :
● Do not press against the lens cover with force. Doing so
may damage the lens or the cover.
Memo :
● The recordable time display should only be used as a
guide.
It is displayed in units of 10 minutes.
● The recordable time shown on the LCD screen may differ
from that shown on the viewfinder.
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
OFF
AF/MF
FULL AUTO
Ⅵ When the power is on
GAIN WHT.BAL
A
/
B
L-
M-
H-
B-
A-
PRST-
A
B
1 . Video shooting mode: Press INDEX three times.
Still picture shooting mode: Press INDEX once.
Lens Cover Switch
2 . Press INDEX to clear the display.
Memo :
● When video shooting is in progress, the information does
not appear.
● When the AC adapter is in use, the information does not
appear.
20
Setting the Date
Setting the Language
The following are steps to change the display language.
1 . Turn on the power.
1 . Turn on the power.
2 . Press MENU.
2 . Press MENU.
MENU
MENU
3 . Select the [DISPLAY SETTINGS] menu.
3 . Select the [DISPLAY SETTINGS] menu.
Push the Set Lever up or down to select, then press the
center.
Push the Set Lever up or down to select, then press the
center.
4 . Select [CLOCK ADJUST].
Push the Set Lever up or down to select, then press the
4 . Select [LANGUAGE].
center.
Push the Set Lever up or down to select, then press the
center.
5 . Set the date and time.
Push the Set Lever up or down to change the setting value.
Push the Set Lever to the left or right to jump to the next digit.
Press the center of the Set Lever to confirm your selection.
5 . Set the desired language.
Push the Set Lever up or down to select.
Press the center of the Set Lever to confirm your selection.
DISPLAY SETTINGS
日本語
CLOCK ADJUST
ENGLISH
FRANÇAIS
DEUTSCH
DATE
TIME
NOV 10 2009 11 35 AM
SELECT SET MENU QUIT
Ⅵ To return to the previous screen, push the Set Lever to the
left.
SELECT SET MENU STOP
Ⅵ To close the menu screen, press MENU.
Display
Language
Japanese
English
Ⅵ To return to the previous screen, push the Set Lever to the
left.
Ⅵ To close the menu screen, press MENU.
French
Memo :
German
message will appear every time you turn on the power.
● You can select the display style of the date and time using
the [DATE DISPLAY STYLE] item in the [DISPLAY
SETTINGS] menu. (A Page 65)
Spanish
Italian
Russian
Simplied Chinese
Assigning Functions to the USER Buttons
This camcorder comes with three USER buttons. A specific
function can be assigned to each USER button according to
your preference.
Set Lever
AUTO MANUAL
USER1 USER2
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
-
LINE
MIC
-
AUDIO
INPUT1
INPUT2
-
-
SELECT
MIC+48V
INPUT1
INPUT2
AUTO MANUAL
IRIS
INDEX
SHUTTER
T
AE
±
REC
W
USER1 USER2
REC
ND
FILTER
ON
USER3
FOCUS
ZOOM
CAM MEDIA
/
USERS
DC
DISPLAY
Q.REVIEW
ME
CAM / MEDIA
USERS
OFF
AF/MF
FULL AUTO
USER3
DISPLAY
Q.REVIEW
MENU
COMPONENT
OUT
A
/
V
OUT
DISPLAY
Q.REVIEW
MENU
GAIN WHT.BAL
A
/
B
L-
B-
M-
H-
A-
P
R
S
T-
A
B
MENU
To do so, make use of [USER1], [USER2], and [USER3] in
the [CAMERA SETTINGS] menu. (A Page 65)
21
Preparations
Ⅵ Adjusting the brightness of the viewfinder/LCD
screen
Settings and Adjustments
Before Use (continued)
When a screen is displayed on the viewfinder, performing
the following steps adjusts the brightness of the viewfinder.
When a screen is displayed on the LCD, the brightness of
the LCD is adjusted.
When a screen is displayed on both the viewfinder and
LCD, only the brightness of the viewfinder is adjusted.
Viewing the Viewfinder/LCD Screen
Select [MONITOR BRIGHT] in the [DISPLAY SETTINGS]
menu. (A Page 65)
You can monitor video images on this camcorder using the
viewfinder, LCD screen, or both.
A slide bar for adjusting the screen brightness appears.
Ⅵ Viewing with the viewfinder
1 . Push the Set Lever to the left or right.
1 . Pull out the viewfinder.
● Doing so moves the slide bar and changes the
brightness of the screen.
2 . Incline the viewfinder vertically to a position that
enables easy viewing.
2 . Press the center of the Set Lever.
3 . Turn the eyepiece focus lever to adjust the focus.
Ⅵ Viewing with the LCD screen
1 . Open the LCD cover.
2 . Incline the LCD cover to a position that enables
easy viewing.
Face-to-face Shooting
Direction
(direction in which the
screen faces the subject)
0
Ⅵ Setting the brightness of the LCD screen backlight
Select [MONITOR BACKLIGHT] in the [DISPLAY
SETTINGS] menu. (A Page 65)
ON
Eyepiece
Focus Lever
ON
Relationship between the viewfinder and LCD screen
displays
VF Status
OFF
LCD Status
OFF
Video Output
VF
ON
OFF
VF
OFF
ON
LCD, VF (T2)
ON
ON
In accordance with the
menu settings (T1)
ON
ON (Face-to-face
shooting direction)
VF and LCD
T1 In accordance with [PRIORITY SETTING] in the [CAMERA
SETTINGS] menu. (A Page 66)
T2 When [PRIORITY SETTING] is set to [ALWAYS-ON
VIEWFINDER]
Memo :
● When the HDMI, COMPONENT OUT or A/V OUT terminal
is connected, video images will not appear on the
viewfinder.
22
Display of selected slot
with an SD card icon
during shooting mode
Inserting an SD Card
(Slot A and Slot B)
Automatic Slot Switch
[
[
]
]
A
B
5h36m
Ⅵ SD cards to use
5h36m
● See ASD CardsB on Page 7.
● SDXC cards are not supported.
Video mode:
Remaining time
Still picture mode:
Remaining number of shots
Door
A/B
Notched Corner
Ⅵ Removing the SD card
Preparation: Turn off the power.
1 . Open the door.
1 . Open the door.
2 . Make sure the SD card to be removed is not being
2 . Insert an SD card with the notched corner first.
3 . Close the door.
accessed (access lamp blinking).
3 . Push the SD card and remove it from the slot.
Ⅵ Selecting a card slot
Press the A/B button.
4 . Close the door.
● Doing so switches between Slot A and Slot B.
Caution :
● When an SD card is inserted, the access lamp of the
selected slot lights up.
● Do not touch the metal part of the SD card when inserting
or removing the SD card.
● When data in the SD card is being accessed, the
access lamp blinks.
Ⅵ Switching between Slot A and Slot B
automatically
Set [SLOT AUTO SWITCHING] in the [CAMERA SETTINGS]
menu to [ON]. (A Page 65)
● When the space on an SD card runs out during
recording in the shooting mode, data is automatically
recorded to the other SD card.
● When playback from an SD card ends in the playback
mode, playback from the other SD card starts
automatically.
● When the Automatic Slot Switch feature is turned [ON],
an automatic slot switch icon appears on the screen.
Memo :
● If the SD card to switch to cannot be read, slot switching
will not be performed.
● When an SD card is inserted into the slot to switch to
during recording, slot switching will not be performed as
the SD card cannot be read. Stop the recording first and
allow the SD card to be read.
23
Preparations
Settings and Adjustments
Before Use (continued)
Resetting the File Number
Each time a recording is performed, the file number stored in
the SD card increases.
You can reset the file number before the next recording
starts.
Ⅵ Resetting a video file number
Select [VIDEO NO. RESET] in the [MEDIA SETTINGS]
Formatting the SD Card
SD cards that are being used for the first time will
be formatted by this camcorder.
When a card that requires formatting is inserted, a message
prompting you to format the card appears on the screen.
Ⅵ Resetting a still picture file number
Select [IMAGE NO. RESET] in the [MEDIA SETTINGS]
menu. (A Page 63)
● A video or still picture reset screen appears.
Push the Set Lever up or down to select [YES], then press
the center of the Set Lever.
NEED TO FORMAT SD CARD
IN SLOT A.
(ALL DATA WILL BE ERASED.)
DO YOU WANT TO FORMAT?
● Video or still picture reset starts.
YES
NO
Video:
SELECT SET MENU QUIT
A parent folder is created for each video file format. When
recording starts after resetting the number, a file is created
with the smallest number that is not used in the
corresponding parent folder.
Push the Set Lever up or down to select [YES], then press
the center of the Set Lever.
● Formatting starts.
A new folder is created with a number by adding one to the
number of the folder where shooting is last performed or to
the largest folder number inside the media.
Ⅵ Formatting the SD card as and when required
Select [FORMAT] in the [MEDIA SETTINGS] menu.
(A Page 63)
Folder/File Number
The formatting screen appears.
Ⅵ Video
1 . Select the slot to perform formatting.
A parent folder is created for each file format
(QuickTime(MOV), MP4).
The file name appears as follows.
2 . Select the content to format.
_0001_01.extension to
: Unique number
(last 3 digits of the camcorder’s serial number)
_9999_99.extension
***
***
***
Files
Erases all files.
Files + File Number Sets the video and still picture file
number to default and erases all
files.
T Up to 600 folders/files for videos in QuickTime(MOV) or
MP4 format can be recorded on the SD card.
Push the Set Lever up or down to select, then press the
center.
● The formatting screen appears.
Ⅵ Still Image
Folder number: 100JVCSO to 999JVCSO
File number : PIC0001.JPG to PIC0999.JPG
3 . Push the Set Lever up or down to select [YES], then
press the center of the Set Lever.
● Formatting starts.
24
Shooting
Selecting a Shooting Mode
Selecting the Full Auto/Manual Shooting
Mode
There are two adjustment modes for shooting, namely the
Full Auto and Manual modes.
Ⅵ Setting to the Full Auto shooting mode
Selecting the Video/Still Picture Shooting
Mode
When FULL AUTO is pressed once, the current adjustment
mode is displayed. Pressing FULL AUTO while the mode is
displayed changes the setting.
Press FULL AUTO to display the Full Auto shooting mode
icon (A) at the top of the screen.
There are two types of shooting modes, namely the video
shooting and still picture shooting modes.
● Exposure, aperture, shutter speed, and white balance
are adjusted automatically.
1 . Set to the shooting mode.
Press CAM/MEDIA.
FULL AUTO
● The camera image appears on the monitor when in the
shooting mode.
Ⅵ Setting to the Manual shooting mode
CAM / MEDIA
Press FULL AUTO to display the Manual shooting mode icon
(M) at the top of the screen.
● Even when the Manual shooting mode is set, the
their icons are not displayed. To adjust the aperture and
shutter speed manually, press the IRIS or SHUTTER
button to display and change the values.
(A Page 37)
2 . Select the video/still picture mode.
The way of operation differs according to the mode.
Still picture mode h Turn the POWER/MODE switch to
video mode
MODE.
Video mode h still
picture mode
Turn the POWER/MODE switch to
MODE and hold for about 1 second.
FULL AUTO
Full Auto Shooting Mode
Manual Shooting Mode
[
]
A
B
0h57m
[
]
5h12m
00:00:00:01
Video Indicating Lamp
Still Picture Indicating Lamp
18dB
ACCESS
IRIS
INDEX
T
SHUTTER
USER1 USER2
ND
AE
REC
FILTER
ON
W
FOCUS
ZOOM
REC
OFF
AF/MF
FULL AUTO
CAM / MEDIA
DC
USERS
GAIN WHT.BAL
A / B
L-
M-
H-
B-
A-
DISPLAY
Q.REVIEW
MENU
PRST-
A
B
POWER/MODE Switch
CAM/MEDIA
FULL AUTO
When in the video mode
● The video indicating lamp lights up.
● A video icon appears at the top of the screen.
When in the still picture mode
● The still picture indicating lamp lights up.
● A still picture icon appears at the top of the
screen.
Memo :
● Still pictures can be recorded when in the video shooting
mode. (A Page 28)
● If the [SYSTEM SELECT] menu is set to [720-**], switching
between the video/still picture mode reboots the
camcorder.
25
Shooting
Selecting a Shooting Mode
(continued)
Using the Camcorder in the
Video Shooting Mode
Selecting a Focusing Mode
Setting the Video Format
There are two focusing modes, namely Auto and Manual.
Ⅵ Setting the video file format
Specify the format of the video file to be recorded on the SD
card. (QuickTime or MP4)
Setting
Ⅵ Setting to the Auto Focus mode
Press AF/MF to display the Auto Focus icon (AF) on the
screen.
Set the [FILE FORMAT] menu. (A Page 61)
● Focus is adjusted automatically.
AF/MF
Ⅵ Setting the video system
Specify the video system (vertical resolution and frame
rate) for this camcorder. Example: 1080-60/30
Setting
Set the [SYSTEM SELECT] menu. (A Page 61)
When settings in this menu are altered, the camcorder will
reboot automatically.
Press AF/MF to display the Manual Focus icon (MF) on the
screen.
● Adjust the focus manually. (A Page 31)
AF/MF
Ⅵ Setting the recording mode
AF
MF
Full Auto Shooting Mode
Manual Shooting Mode
Specify the horizontal resolution, frame rate, scan method,
and picture quality mode. Example: 1920/60i(HQ)
Setting
[
[
]
]
A
B
0h57m
Set the [REC MODE] menu. (A Page 62)
5h12m
● The selected recording mode appears at the top of the
screen.
00:00:00:01
18dB
Video Recording Mode Display
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
OFF
AF/MF
FULL AUTO
GAIN WHT.BAL
A / B
L-
M-
H-
B-
A-
PRST-
A
B
AF/MF
Memo :
● The color of the recording mode display changes
according to the settings in the [FILE FORMAT] menu.
When set to [QuickTime file format] : Blue
When set to [MP4 file format]
: Orange
26
Displaying the Remaining Space on the
Shooting Videos
SD Card
Preparation: Set to the video shooting mode. (A Page 25)
This camcorder comes with two REC buttons for shooting
videos. (Located at the rear and on the LCD cover)
You can shoot videos using any of the two buttons.
Displays a pie chart, which shows the remaining space on
the SD card and the remaining time for each video recording
mode.
Preparation: Insert an SD card.
1 . Press REC.
● Recording starts.
1 . Display the remaining time.
Press INDEX.
● The remaining time on the SD card is displayed.
REC
REC
INDEX
[
]
0h57m
[
]
B
5h12m
00:00:00:01
File Icon
Displays the selection made in the [FILE FORMAT] menu. The
display color changes according to the file format.
:
:
Blue
QuickTime file format
MP4 file format
Recording Mode
Orange
2 . Press REC.
● Recording stops. (Record Pause)
Vertical Resolution Icon (1080 or 720)
Displays the selection made in the [SYSTEM SELECT]
menu.
SD Card Slot
REC
REC
MAX RECORDING TIME
SD A
1h30m
1h20m
2h10m
FREE
USED
REC
1h40m
IRIS
INDEX
T
SHUTTER
INDEX
SORT
AE
±
REC
W
Displays the icon of the recording mode that is determined by
the video system.
REC
DC
CAM / MEDIA
USERS
The remaining recording time of the currently selected
recording mode is hightlighted. You can change the recording
mode using the settings in the [REC MODE] menu.
DISPLA
Y
Q.REVIEW
MENU
Q.REVIEW
REC
INDEX
Memo :
● The maximum size for each video file is 4 GB. The file is
split into two or more files if the size exceeds 4 GB.
● Recording stops when there is no more space left on the
SD card. If [SLOT AUTO SWITCHING] in the [CAMERA
SETTINGS] menu is set to [ON], recording to the other SD
card will start automatically.
2 . Press INDEX repeatedly to change the remaining
time/battery power display in the following sequence.
● When using AC adapter
Slot A B Slot B B End of Display
● When using battery
Slot A B Slot B B Battery Power B End of Display
27
By using the continuous clip recording feature, however,
multiple clips with pauses in between the recordings can be
created into a single video file.
Video Shooting Mode
(continued)
Ⅵ Set to the continuous clip recording mode
Set the [CLIP CONTINUOUS REC] menu to [ON].
● AC.CONTB appears on the screen.
[
]
0h57m
Checking the most recently recorded video
[
]
B
5h12m
00:12:3 4:01
1 . Set to the Record Pause mode.
2 . Press Q.REVIEW.
● The last 5 seconds of the preceding scene is played back.
C.CONT
● After playback ends, the video switches to the Record
Pause mode.
Q.REVIEW
● While the [CLIP CONTINUOUS REC] menu is set to [ON],
the RW icon lights up in yellow during Record Pause
mode.
Ⅵ Ending the file
To end the file during recording:
Press REC for 1 second or longer.
To start recording immediately during quick review, press
REC twice.
Ⅵ Deleting the preceding scene file
During quick review, press the USER button that is set
To end the file during Record Pause mode:
Press the USER button that is set as [CLIP CONTINUOUS
OFF].
Assigning functions to the USER buttons: (A Page 21, 65)
Alternatively, set the [CLIP CONTINUOUS REC] menu to
as [DELETE].
Assigning functions to the USER buttons: (
A
Page 21, 65)
USER
[OFF].
USER
Capturing Still Pictures in the Video
Shooting Mode
● When you are ending the file, the RW icon on the screen
blinks in yellow.
Press SNAPSHOT all the way down during
recording or pause mode.
● When a still picture is captured, APHOTOB appears on the
monitor screen.
[
]
0h57m
[
]
B
5h12m
00:12:3 4:01
RW
SNAP
SHOT
Blinks in yellow
SNAPSHOT
Ⅵ Precautions during recording
● Do not remove the SD card. To remove the SD card, end
the file first.
● When the remaining space on the SD card runs out,
recording stops and the file is ended.
● When the [POWER] switch is turned off or when power is
low due to low battery power, recording stops and power
is cut off after the file is ended.
Memo :
● Up to three still pictures can be captured during each
recording.
Ⅵ Precautions during Record Pause mode
● When recording is in the pause mode, an unlimited
number of still pictures can be captured as long as there is
sufficient space on the SD card. However, Automatic Slot
Switch is disabled in this case.
● Still pictures are not captured if SNAPSHOT is pressed
halfway.
(RW icon lights up in yellow)
● It is not possible to change to the playback or still picture
mode. To change the operation mode, end the file first.
● Quick review does not function. To play back using quick
review, close the file.
● Still pictures are captured at a size of 1920 x 1080.
● Continuous shooting, bracket shooting, and the self-timer
features are invalid.
● When the [SYSTEM SELECT] menu is set to [720-**], still
pictures cannot be captured.
● Do not remove the SD card. To remove the SD card, end
the file first.
● When the [POWER] switch is turned off or when power is
low due to low battery power, recording stops and power
is cut off after the file is ended.
● Do not turn off the power directly by detaching the battery
or removing the AC adapter.
Recording Multiple Clips as a Continuous
File
Normally, each recording process is saved as a separate file
in the SD card.
28
Using the Camcorder in the
Still Picture Shooting Mode
Capturing Still Pictures
Preparation: Set to the still picture shooting mode.
(A Page 25)
1 . Press [SNAPSHOT] halfway.
● The camcorder automatically adjusts the focus and
exposure. Once the adjustment is complete, the focus
icon turns green, and the shutter speed is displayed.
Setting the Picture Quality, Recording
Size, and Sensitivity
(A Page 25)
[
[
]
]
A
B
0010
Ⅵ Picture quality
9999
Set the [IMAGE QUALITY] menu. (A Page 67)
displayed on the monitor screen.
Ⅵ Picture size
Shutter Speed
Display
Focus Icon
Set the [IMAGE SIZE] menu. (A Page 67)
displayed on the monitor screen.
2 . Press [SNAPSHOT] all the way down.
● A still picture is recorded. APHOTOB appears on the
Ⅵ Sensitivity
monitor screen during the recording process.
Set the [GAIN UP] menu. (A Page 68)
Remaining Number of Shots
Size
Picture Quality
[
[
]
]
A
B
0010
9999
[
]
]
A
B
9999
[
9999
Recording
SNAPSHOT
29
Still Picture Shooting Mode
(continued)
Zoom Operation
Preparation: Set to the video shooting or still picture shooting
mode.
Checking the most recently captured still picture
1 . Press Q.REVIEW.
Adjusts the angle of view.
Zoom ratio: 1x to 10x (optical zoom only)
● The most recently captured still picture is displayed.
Q.REVIEW
Zooming can be operated using any of the four levers/rings
below.
2 . Press Q.REVIEW again to return to the camera
image.
A Camcorder’s zoom lever on the top surface
Ⅵ Deleting the most recently recorded image
B Camcorder’s manual ring:
This can be used as a zoom ring when the [FOCUS/
ZOOM] ring switch at the side of the camcorder is set to
ZOOM.
During quick review of still pictures, press the USER
button that is set as [DELETE].
Assigning functions to the USER buttons:(
A
Page 21, 65)
C Sub zoom lever on the LCD cover
AUTO MANUAL
CH-1
CH-2
CH-2 INPUT
INPUT1
A
UDIO INPUT
-
LINE
MIC
-
A
UDIO
-
-
SELECT
D Zoom lever on the remote control
INPUT2
MIC+48V
INPUT1
INPUT2
A
UTO MANUAL
The priority order of these levers/rings is in the sequence
A > B > C > D.
CAM / MEDIA
MENU
USERS
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
CAM MEDIA
/
USERS
DISPLAY
Q.REVIEW
DISPLAY
Q.REVIEW
MENU
OFF
AF/MF
FULL AUTO
COMPONENT
OUT
A
/
V
OUT
A Zoom Lever
GAIN WHT.BAL
A
/
B
L-
M-
H-
B-
A-
P
R
S
T
-
A
B
Q.REVIEW
W
T
B Manual Ring
Continuous shooting
Still pictures are captured continuously while
[SNAPSHOT] is pressed down.
Set the [SHUTTER MODE] menu to [CONTINUOUS
SHOOTING]. (A Page 68)
INDEX
T
RO
G
E A
W
REC
C Sub Zoom Lever
Three shots with different brightness levels are captured
continuously.
Set the [SHUTTER MODE] menu to [BRACKETING].
(A Page 68)
Ring switch set to ZOOM
You can make use of the 2 or 10-second self-timer.
Set the [SELF-TIMER] menu to [2SEC] or [10SEC].
(A Page 68)
2x
8x
Memo :
● Continuous shooting is disabled when using the self-timer.
W
T
Continuous Shooting Mode
Bracket Shooting Mode
[
[
]
]
A
B
0010
9999
10
Self-Timer
30
Adjusting the Focus
Manually
Using the Focus Assist Function
This feature temporarily switches the screen to black-and-
Ⅵ There are two ways to activate the Focus Assist function.
A Set [FOCUS ASSIST] in the [CAMERA PROCESS] menu
Preparation: Set to the video shooting or still picture shooting
mode.
to [ON]. (A Page 59)
Or
Ⅵ Setting to the Manual Focus mode
B Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to the Focus Assist function, then
press the corresponding USER button. (A Page 21, 65)
Press AF/MF to display the Manual Focus icon (MF).
AF/MF
Color added
[
]
A
B
0h57m
[
]
5h12m
00:00:00:01
18dB
Manual Focus Mode
1 . Set the [FOCUS/ZOOM] ring switch to FOCUS.
Doing so enables you to use the manual ring of the lens
as a focus ring.
2 . Turn the manual ring to adjust the focus.
Focus Assist enabled
Using the Focus Assist function on the right helps to
Turn the manual ring to add color to where you want to
focus.
enable easy focusing.
Ring switch set to FOCUS
Ⅵ Canceling Focus Assist
Set the [FOCUS ASSIST] menu to [OFF].
Manual Ring
Or
Press the USER button that is assigned the Focus Assist
function.
Memo :
● To change the contour color, use the [FOCUS ASSIST
COLOR] setting in the [CAMERA PROCESS] menu.
(BLUE, GREEN, RED)
When using the Focus Assist function at a dark place, the
point where color is added may appear grainy, making the
contour color unclear.
AF/MF
● When [DISPLAY ON TV] in the [CONNECTION
SETTINGS] menu is set to [ON], the Focus Assist display
is output on the external monitor. Set [DISPLAY ON TV] to
[OFF] to clear the display on external monitors.
31
Shooting
Shooting Different Scenes
and Conditions
(Program AE)
Enabling Lolux Mode with the USER
Button
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Lolux mode
:
Increases the sensitivity when in dim surroundings.
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
You can adjust the exposure and shutter speed according to
the subject to ensure that shooting is performed with the
optimal settings.
1 . Assign the Lolux feature to a USER button.
Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to [Lolux].
(A Page 21, 65)
1 . Open the Program AE selection screen.
2 . Press the USER button that is assigned the feature.
Push the Set Lever to the right.
Lolux mode starts, and ALoluxB appears on the screen.
3 . Canceling Lolux mode.
Press the USER button that is assigned the feature.
Memo :
● When shooting in Lolux mode, secure the camcorder using
a tripod as camera shakes may blur the image.
● Shutter speed and gain cannot be adjusted when setting
Lolux in the video mode.
OFF
PORTRAIT
SPORTS
SNOW
Using the Built-in ND Filter
2 . Select the most appropriate mode, and confirm the
selection.
Push the Set Lever up or down to select a mode, then press
the center to confirm. Or, push the Set Lever to the right.
● The Program AE screen closes, and the icon of the
selected mode appears on the screen.
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Adjust the amount of light from the lens by turning the ND
FILTER switch ON/OFF to enable/disable the built-in ND
filter. Set the filter to AONB when shooting at a bright outdoor
location.
SPORT
Set Lever
IRIS
INDEX
SHUTTER
T
AE
±
REC
ND FILTER Switch
W
REC
Ⅵ Set the ND FILTER switch to ON.
DC
● Reduces the amount of incident light to about 1/10.
ANDB appears on the screen.
Settings
OFF
: Disables Program AE.
PORTRAIT
: Blurs the background to highlight the
subject.
SPORTS
: Captures fast moving subjects clearly in
every single frame.
ND
SNOW
: Prevents the subject from appearing too
dark, such as when shooting a snowfield on
a sunny day.
Memo :
● Enabling ND FILTER during shooting may cause distortion
in the image or noise in the audio sound.
SPOTLIGHT
: Prevents the human subject from appearing
too bright under light.
TWILIGHT
: Makes evening scenes look more natural.
32
Ⅵ Canceling AE Lock
Press the ADJ./VOL. knob for 1 second or longer.
● The mark disappears.
Adjusting the Exposure
Manually
Ⅵ Disabling the Manual Exposure mode
● Press AE .
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
AE
Generally, the brightness of the subject that is being shot is
automatically adjusted according to the reference values of
the camera. However, the brighter or darker areas of an
image may appear unclear depending on the shooting
conditions. To prevent this from occurring, you can correct
the exposure manually.
ACCESS
IRIS
SHUTTER
OPEN
AE
±
REC
AE
CLOSE
1 . Set to the Manual Exposure mode.
ADJ./VOL.
Knob
DC
Press AE .
●
The AE value appears on the screen, and the adjustment
mode is enabled.
Memo :
● AE Lock is canceled if the shutter speed or aperture is set
to the manual mode.
● When in the still picture mode, exposure cannot be
adjusted manually if shutter speed and aperture are set to
the manual mode. (The AE display flashes for about 5
seconds on the screen and its setting becomes invalid.)
(Control using the EV value when in the still picture mode.)
AE
AE Value
0
Using the Tele Macro
Feature
2 . Adjust the exposure.
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Shortens the closeup distance at the tele (T) end of the
zoom.
Turn the ADJ./VOL. knob.
Turn upward to increase the value and make the image
brighter.
Turn downward to decrease the value and make the image
darker.
(1 m B approx. 80 cm)
Ⅵ Set [TELE MACRO] in the [CAMERA PROCESS] menu to
[ON].
3 . Confirm the setting value.
(Possible only in Manual mode M)
(A Page 61)
Press the ADJ./VOL. knob.
● The manual setting value is set. (The setting value (-6 to
+6) is displayed on the screen.)
SETTINGS] menu to [TELE MACRO], then press the
corresponding USER button.
(Possible in Full Auto mode A and Manual mode M)
Assignment of USER buttons:(A Page 21, 65)
● When the tele macro feature is turned on, a tele macro
icon appears on the screen.
4 . After setting the value, press the ADJ./VOL. knob for
1 second or longer to switch to the AE Lock mode.
Tele Macro Icon
(An L mark appears after the setting value on the
screen.)
AE Lock: Locks the exposure setting value.
-6
18dB
AE Lock
Memo :
● Between the two methods above, setting via the USER
button is given a higher priority.
33
Shooting
Displaying the Zebra
Pattern
Specifying the Luminance Level Range for
Displaying Zebra Pattern
You can specify the upper limit (
the luminance level range.
) and lower limit (
) of
This is set to the range of 70 % to 80 % by default.
Applicable to: Video shooting mode
A Full Auto Shooting Mode
M Manual Shooting Mode
Ⅵ Set [ZEBRA] in the [CAMERA PROCESS] menu to
[THRESHOLD].
During video shooting, diagonal lines (zebra pattern) are
displayed only at areas with the specified luminance levels.
You can specify the luminance level range for displaying the
zebra pattern.
● A slide bar for setting the upper limit appears.
There are two ways to display the zebra pattern.
0% - 80%
Ⅵ Set [ZEBRA] in the [CAMERA PROCESS] menu to [ON].
(A Page 59)
Ⅵ Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to [ZEBRA], then press the
corresponding USER button.
: Upper Limit Setting
: Lower Limit Setting
Assignment of USER buttons: (A Page 21, 65)
1 . Select whether you are setting the upper limit or
lower limit.
● A zebra pattern is displayed at the area that corresponds
to the specified luminance level.
Push the Set Lever up or down.
Zebra Pattern
2 . Select a setting value.
Move along the slide bar by pushing the Set Lever to the left
or right.
● The display area of the zebra pattern changes.
3 . Confirm the setting value.
Press the center of the Set Lever.
● The slide bar disappears.
Memo :
● Between the two methods above, setting via the USER
button is given a higher priority.
● The zebra pattern is not displayed when in the still picture
shooting mode.
● When [DISPLAY ON TV] in the [CONNECTION
SETTINGS] menu is set to [ON], the zebra pattern is
output on the external monitor. Set [DISPLAY ON TV] to
[OFF] to clear the display on external monitors.
Ⅵ Clearing the zebra pattern display
Set the [ZEBRA] menu to [OFF].
Alternatively, press the USER button that is set as
[ZEBRA].
34
Adjusting the White
Adjusting Automatic White Balance
Balance
As the color of the light (color temperature) varies according
to the light source, it is necessary to readjust the white
balance when the main light source illuminating the subject
changes. You can store two white balance types in memories
A and B.
Applicable to: Manual shooting mode M
Ⅵ Set to the Manual shooting mode.
Ⅵ Set to the Manual shooting mode.
1 . Set the ND filter according to the lighting.
2 . Set the WHT.BAL. switch to A or B.
Ⅵ Select a white balance type using the WHT.BAL.
switch.
You can select one of the three white balance types using the
WHT.BAL. switch.
3 . Locate a place with similar lighting conditions as
the subject, place a white object near the center of
the screen and zoom in to fill the screen with white.
WHT.BAL.
Description
Switch
B
Switches to the white balance type that
is stored in Position B. If automatic
white balance adjustment is performed
at this position, the adjusted white
balance is saved to Position B.
4 . Press the Auto White Balance button.
A
Switches to the white balance type that
is stored in Position A. If automatic
white balance adjustment is performed
at this position, the adjusted white
AWB
PRST(PRESET) Switches to the white balance setting
(3200K or 5600K) in [PRESET TEMP.]
of the [CAMERA PROCESS] menu.
(A Page 60)
AWB Button
● [AUTO WHITE A(B) OPERATION] is displayed while Auto
White Balance is starting up.
Memo :
● When the correct white balance is obtained, [AUTO
WHITE A(B) OK] is displayed for about 5 seconds.
● You can assign the FAW (Full Auto White Balance) mode
to the WHT.BAL. switch. (A Page 36)
AUTO WHITE A
OK
Error displays
ND FILTER
WHT.BAL. Switch
If the white balance adjustment is not correctly completed,
one of the following messages will appear for about 5
seconds.
● NG:OBJECT
Displayed when there is not enough white color on an
object, or when the color temperature is not suitable. Use
another white object and adjust the white balance again.
● ERROR:LOW LIGHT
Displayed when the light is too dim. Increase the intensity
of the lighting, and adjust the white balance again.
● ERROR:OVER LIGHT
Displayed when the light is too bright. Decrease the
intensity of the lighting, and adjust the white balance again.
Memo :
● Do not use highly reflective objects, such as metals. Doing
so may result in improper white balance adjustment.
35
Shooting
Adjusting the White
Balance (continued)
Adjusting White Paint
Applicable to: Manual shooting mode M
Adjusts the red (R) and blue (B) components when in the
Auto White Balance mode.
Ⅵ Set to the Manual shooting mode.
Using the Full Auto White Balance (FAW)
Function
1 . Select [WHITE PAINT<R>] or [WHITE PAINT<B>] in
the [CAMERA PROCESS] menu.
[WHITE PAINT<R>]: Adjusts the red component.
[WHITE PAINT<B>]: Adjusts the blue component.
The FAW function adjusts the white balance value
automatically as the lighting condition changes.
This mode is convenient when you have no time to adjust the
white balance or when the camcorder is moved frequently in
and out of places with different lighting conditions.
● The white paint adjustment screen is displayed.
1 . Set using [FAW] in the [CAMERA PROCESS] menu.
Assign the FAW function to one of three WHT.BAL.
switches (A, B, PRESET). (A Page 60)
0
2 . Set the WHT.BAL. switch to the position that is
assigned the FAW function.
Slide Bar
B-
A-
2 . Move along the slide bar on the adjustment screen
PRST-
by pushing the Set Lever to the left or right.
● The red or blue component on the screen changes.
Caution :
● The FAW function cannot provide optimum white balance
with a subject outside the FAW adjustment range, for
example when it contains only a single color or not enough
white color.
● The accuracy of FAW is inferior to that of Auto White
Balance.
● When the power of the camcorder is turned on with the
FAW mode selected, it takes about 10 seconds for the
FAW adjustment to complete. Do not start recording during
this interval.
3 . Press the center of the Set Lever.
● The value is set.
Memo :
● Readjusting AWB (Auto White Balance) resets the
respective colors (R and B) to their default settings.
36
2 . Select a shutter speed value.
Turn the ADJ./VOL. knob up or down.
● The selected value is displayed.
Adjusting Manual Gain
3 . Confirm the shutter speed value.
Applicable to: Video shooting mode
Manual shooting mode M
Press the ADJ./VOL. knob.
● Doing so exits the adjustment mode and the shutter
speed is displayed in white.
Ⅵ Set to the Manual shooting mode.
The light sensitivity can be electrically boosted using the
GAIN switch when there is insufficient illumination on the
subject. (3 positions)
ACCESS
GAIN Switch
Description
IRIS
SHUTTER
OPEN
L
M
H
0 dB (No boosting is applied.)
SHUTTER
AE
±
REC
CLOSE
9 dB (Boosts sensitivity by about 3 times.)
18 dB (Boosts sensitivity by about 8 times.)
ADJ./VOL.
Knob
DC
The boosting level for each position can be specified using
[GAIN L], [GAIN M], and [GAIN H] in the [CAMERA
PROCESS] menu.
Memo :
● When in the still picture mode, shutter speed cannot be
adjusted manually if exposure and aperture are set to the
manual mode. (The S.SP display flashes for about 5
seconds on the screen and its setting becomes invalid.)
● When in the Lolux mode, shutter speed cannot be adjusted
manually. (The S.SP display flashes for about 5 seconds
on the screen and its setting becomes invalid.)
Memo :
● Boosting the sensitivity causes the screen to appear
grainier.
● When in the Full Auto mode, this is fixed at AGC (Auto
Gain Control). However, when Program AE is set to
[TWILIGHT], the gain value is automatically set to 0 dB.
Ⅵ Setting values
Video frame rate 60
1/3.75,1/7.5,1/15,1/30,1/60,1/80,1/100,
1/250,1/500,1/1000,1/2000,1/4000,1/10000
Video frame rate 50
1/3.13,1/6.25,1/12.5,1/25,1/50,1/80,1/120,
1/250,1/500,1/1000,1/2000,1/4000,1/10000
GAIN Switch
Video frame rate 24
1/3,1/6,1/12,1/24,1/48,1/60,1/100,1/250,1/500,
1/1000,1/2000,1/4000,1/10000
Adjusting the Shutter
Speed
Still picture
1/4,1/8,1/15,1/30,1/60,1/80,1/125,1/250,1/500,
1/1000,1/2000,1/4000,1/8000
Ⅵ Setting shutter speed to AUTO
Press the SHUTTER button twice to clear the display.
Applicable to: Manual shooting mode M
The shutter speed can be set to a value according to the
user’s preference. When this is set to Auto, the shutter speed
is automatically controlled.
Adjusting the Aperture
Ⅵ Set to the Manual shooting mode.
1 . Set to the shutter speed adjustment mode.
Press the SHUTTER button.
Applicable to: Manual shooting mode M
● Video mode
: The shutter speed that is set in the
manual mode is displayed.
The aperture value (F-number) of the lens can be set as follows.
● Still picture mode : The current shutter speed is
F-number
Decrease
Description
The subject appears brighter.
The focused range becomes sharper, while the
background is blurred to produce a soft image.
displayed.
SHUTTER
Increase
The subject appears darker.
Background of image becomes focused as well.
37
Shooting
Ⅵ Set to the Manual shooting mode.
Setting the Photometry
Area
1 . Set to the aperture adjustment mode.
Press the IRIS button.
● The current F-number is displayed.
IRIS
Applicable to: Manual shooting mode M
2 . Select an F-number.
Brightness of a specific area can be corrected automatically
to the optimal state by selecting one of the three photometry
areas indicated by the frames on the screen.
Turn the ADJ./VOL. knob up or down.
● The selected F-number is displayed.
Set using [PHOTOMETRY AREA] in the [CAMERA
PROCESS] menu.
When [PHOTOMETRY AREA] is set to [WHOLE SCREEN],
the brightness of the entire screen is automatically adjusted
to an optimal level.
3 . Confirm the F-number.
Press the ADJ./VOL. knob.
Ⅵ Set to the Manual shooting mode.
● Doing so exits the adjustment mode and the F-number is
displayed in white.
1 . Display the photometry area setting screen.
Set [PHOTOMETRY AREA] in the [CAMERA PROCESS]
menu to [SPOT].
● The photometry area frame is displayed at the center of
the screen.
ACCESS
IRIS
The photometry area icon appears in blue.
(Select a photometry area from the left, center, and right
frames on the screen.)
IRIS
SHUTTER
OPEN
AE
±
REC
CLOSE
ADJ./VOL.
Knob
Photometry Area Icon Photometry Area Frame
DC
Memo :
● The F-number appears in yellow if it is different from the
preset value.
● When in the still picture mode, aperture cannot be
adjusted manually if exposure and shutter speed are set to
the manual mode. (The A.PR display flashes for about 5
seconds on the screen and its setting becomes invalid.)
2 . Select a photometry area.
Push the Set Lever to the left or right.
Ⅵ Setting values
The right or left photometry area frame is displayed.
F1.8 - F8.0 (14 steps)
The open F-number of the aperture varies according to the zoom
position.
Wide (W) end : F1.8
Tele (T) end : F2.8
Ⅵ 1/3-step display when zooming to the tele (T) end
3 . Confirm the photometry area.
When the aperture is set to F1.8 at the (W) end of the zoom
range, the aperture value may fall below the open F-number
when zoomed to the (T) end. In this case, the aperture value is
not fixed, but changes according to the open F-number of the
respective zoom positions. The F-number nearest to the open F-
number is displayed in 1/3 steps. (F1.8, F2.0, F2.2, F2.5, F2.8)
Press the center of the Set Lever.
● The confirmed photometry area is displayed, and the
photometry area icon appears in white.
● Brightness within the frame is always automatically
corrected to an optimal level.
Ⅵ Setting aperture to AUTO
Press the IRIS button twice to clear the display.
Ⅵ Locking the brightness of the photometry area
Press the center of the Set Lever for 1 second or longer while
setting the photometry area or after confirming the setting.
● The photometry area frame disappears, and a Lock icon
(L) appears.
● The automatically corrected brightness within the
photometry area is locked. (AE Lock)
Ⅵ Setting the entire screen as the photometry area
Set [PHOTOMETRY AREA] in the [CAMERA PROCESS]
menu to [WHOLE SCREEN].
38
Displaying the Color Bar
Adjusting the Camera
Image
Applicable to: Manual shooting mode M
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Ⅵ Set to the Manual shooting mode.
The picture quality of the camera can be set using the
[CAMERA PROCESS] menu.
Adjustment screens are displayed for the following items in
the [CAMERA PROCESS] menu.
Displays the color bar on the screen and starts recording in
As the adjustments are shown on the screen, you can adjust
the values while checking the picture quality on the camera.
There are two ways to display the color bar.
Ⅵ Set [COLOR BAR] in the [CAMERA PROCESS] menu to
[ON]. (A Page 61)
Ⅵ DETAIL LEVEL
Ⅵ Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to [COLOR BAR], then press the
corresponding USER button.
Ⅵ DETAIL V/H BALANCE
Ⅵ GAMMA LEVEL
Ⅵ COLOR GAIN
Assignment of USER buttons: (A Page 21, 65)
For details of the respective items, see the [CAMERA
PROCESS] menu. (A Page 59)
● The color bar appears.
Memo :
● Between the two methods above, setting via the USER
button is given a higher priority.
Example: DETAIL LEVEL
Detail Icon
● When in the Full Auto shooting mode, the color bar will not
appear.
Ⅵ Clearing the color bar display
Set the [COLOR BAR] menu to [OFF].
Alternatively, press the USER button that is set as
[COLOR BAR].
0
Ⅵ Recording the color bar
When the [SYSTEM SELECT], [REC MODE] menu is as
below, the color bar can be recorded.
Slide Bar
SYSTEM SELECT
1080-60/30
1080-50/25
720-60/30
REC MODE
1920/60i(HQ), 1920/30p(HQ)
1920/50i(HQ), 1920/25p(HQ)
1280/60p(HQ), 1280/60p(SP)
1280/50p(HQ), 1280/50p(SP)
1 . Adjust accordingly.
Push the Set Lever to the left or right.
● Doing so moves the slide bar in the same direction. The
detail level of the camera image changes according to the
movement along the slide bar.
720-50/25
Ⅵ On-screen display on the external monitor
If the [SYSTEM SELECT] menu is set to [720-**], the on-
screen display will appear as usual when the color bar is
output on the external monitors below. ([DISPLAY ON TV]
setting in the [CONNECTION SETTINGS] menu is invalid.)
● A/V OUT terminal
● D1 (480i/576i) output of COMPONENT OUT terminal
● 480i/480p/576i/576p output of HDMI terminal
2 . Confirm the adjusted value.
Press the center of the Set Lever.
● The menu screen closes.
Memo :
● When the setting values of the [GAMMA], [COLOR
MATRIX], and [KNEE] items in the [CAMERA PROCESS]
menu are altered, the change is reflected instantly on the
screen. (A Page 59)
39
Shooting
Audio Recording
Using an External Microphone Connected
to the INPUT1/INPUT2 Terminal
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Preparation: Connect a microphone to the INPUT1/INPUT2
terminal. (A Page 18)
Applicable to: Video shooting mode
Terminal
INPUT1
Audio Input
Input to CH-1(L) at all times. Input to CH-2(R) can
be enabled using the CH-2 INPUT switch.
There are three ways to input audio sound.
A Built-in microphone
INPUT2
Input to CH-2(R) can be enabled using the CH-2
B MIC terminal
INPUT switch.
C INPUT1 terminal / INPUT2 terminal
Ⅵ Selecting CH-2 audio
The priority order of the input is in the sequence of C > B >
A.
Configure the CH-2 INPUT switch
INPUT1: Inputs the audio from the INPUT1 terminal to CH-2.
INPUT2: Inputs the audio from the INPUT2 terminal to CH-2.
TWhen the built-in microphone or MIC terminal is in use,
remove the audio unit cable from the AUDIO IN terminal.
Memo :
● The audio from the INPUT1 terminal is input to CH-1
regardless of the setting.
C INPUT1/INPUT2 Terminals
A Built-in Microphone
Ⅵ Selecting the audio input to the INPUT1 or
INPUT2 terminal
Configure the INPUT1/INPUT2 AUDIO INPUT switch.
Audio Unit Cable
LINE
: Use this setting when connecting to an
audio device or other equipment.
B MIC Terminal
MIC
: Use this setting when connecting to a
dynamic microphone.
Memo :
MIC+48V : Use this setting when connecting to a
microphone that requires a +48 V power
supply (phantom microphone), or when
using the supplied microphone.
● Audio sound is not recorded when in the still picture
shooting mode.
Caution :
Setting the Reference Audio Recording
Level
● When connecting a device that does not require a +48 V
power supply, make sure that it is not set to the MIC+48V
position.
mode M
Menu settings
Ⅵ Adjusting the audio recording level
Select a method for adjusting the audio recording level.
Set the [AUDIO REF. LEVEL] menu.
(-20 dB/-12 dB) (A Page 64)
Configure the CH-1/CH-2 audio select switch.
Select whether to set each channel to the AUTO or
MANUAL mode.
AUTO
: Use this setting to enable the auto
adjustment mode.
Using the Built-in Microphone
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
MANUAL : Use this setting to enable the manual
adjustment mode. Adjust the audio
recording level using the CH-1/CH-2
AUDIO LEVEL knob.
Ⅵ Setting the input level.
Menu settings
Set the [INTERNAL MIC LEVEL] menu.
(A Page 64)
CH-1/CH-2 Audio Selection Switch
CH-2 INPUT
Switch
Using an External Microphone Connected
to the MIC Terminal
INPUT1/INPUT2 AUDIO INPUT Switch
CH-1/CH-2 AUDIO LEVEL Knob
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Preparation: Connect a microphone to the MIC terminal.
(A Page 18)
Reducing Wind Noise
Wind noise for each microphone can be reduced.
Menu settings
Set the [WIND CUT] menu. (A Page 63)
Ⅵ Setting the input level.
Menu settings
Set the [MIC LEVEL SETTING] menu. (A Page 64)
40
Monitoring Audio Sound
Using a Headphone
Time Code Recording
Setting
Applicable to: Video shooting mode, video playback mode
Applicable to: Video shooting mode
Ⅵ Connecting the headphone
Connect the headphone to the headphone (
) jack.
Displaying the Time Code/User’s Bit
Menu settings
Ⅵ Set [TC DISPLAY] in the [TC/UB] menu to [TC] or [UB].
TC: Displays the time code.
UB: Displays the user’s bit.
Time Code
Headphone Jack
stereo sound
Menu settings
Set the [AUDIO MONITOR] menu.
(A Page 64)
Ⅵ Adjusting the headphone’s audio level
Recording the Time Code
Turn the ADJ./VOL. knob.
generator as well as user’s bit can be recorded. The time
code generator comes in the preset and regeneration
modes. When in the preset mode, you can set the time
code and user’s bit freely. (A Page 42)
ACCESS
IRIS
SHUTTER
OPEN
AE
±
REC
CLOSE
Ⅵ Recording time code and user’s bit in the preset
ADJ./VOL.
Knob
mode
DC
Menu settings
Set [TC GENE.] in the [TC/UB] menu to [FREE] or [REC].
FREE
: The time code operates in the run mode at all
times.
REC
: The time code operates in the run mode only
during recording.
Ⅵ Recording time code in continuation of the
recorded time code on the SD card
Menu settings
Set [TC GENE.] in the [TC/UB] menu to [REGEN].
Memo :
● When recording is stopped and the SD card is removed,
the time code will be displayed as follows.
[REC], [REGEN] : Time code generated when the
recording was last stopped.
[FREE]
: Operates in the run mode at all times.
41
Shooting
Time Code Recording
Setting (continued)
1 . Select the [TC PRESET] menu, and press the center
of the Set Lever.
● The time code preset screen appears.
Sets all digits to “0”.
Presetting the Time Code/User’s Bit
TC PRESET
There are two ways to display the [TC/UB] menu.
Ⅵ Display the menu screen using the MENU button, then
00 : 00 : 00 : 00
RESET
select the [TC/UB] menu. (A Page 64)
Ⅵ Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to [TC SETTING], then press the
corresponding USER button.
SELECT SET MENU STOP
Assignment of USER buttons: (A Page 21, 65)
Displayed as “.” when in the drop frame mode.
Displayed as “:” when in the non-drop frame mode.
Setting the time code
Use the method above to display the [TC/UB] menu.
2 . Set the time code (hour, minute, second, frame).
Push the Set Lever up or down to change the setting value.
Push the Set Lever to the left or right to jump to the next digit.
Ⅵ Setting the run mode of the time code generator.
Set the [TC GENE.] menu to [FREE] or [REC].
FREE
REC
: The time code operates in the run
mode at all times.
: The time code operates in the run
mode only during recording.
3 . Confirm the time code setting.
Press the center of the Set Lever.
● Returns to the [TC/UB] menu.
Ⅵ Setting the framing mode of the time code generator.
Set [DROP FRAME] to [DROP] or [NON DROP].
DROP
: The time code generator operates in
the drop frame mode. Use this setting
when placing emphasis on the
recording time.
Ⅵ Closing the menu screen
Press MENU.
● The normal screen is displayed.
MENU
NON DROP : The time code generator operates in
the non-drop frame mode. Use this
setting when placing emphasis on the
number of frames.
Presetting the user’s bit
Memo :
Select [UB PRESET] in the [TC/UB] menu. The method
for setting the user’s bit is the same as the method for
setting the time code. An alphanumeric character
between 0 to 9 and A to F can be specified for each digit.
● [DROP FRAME] cannot be set when the frame rate is set
to 50, 25, or 24.
● Even when the [DROP FRAME] menu is set to [DROP],
the targeted drop frames are not skipped automatically in
the [TC PRESET] menu. They will be skipped
automatically during recording.
42
Playback
Selecting the Video/Still
Picture Playback Mode
Playing Videos on the SD
Card
There are two types of playback modes, namely the video
playback and still picture playback modes.
Preparation: Insert an SD card, and select the card slot.
Ⅵ Changing the video format to play back
Menu settings (A Page 61)
1 . Set to the playback mode.
[FILE FORMAT]
: For selecting the format of the
recorded file.
Press CAM/MEDIA.
● The playback mode is enabled, and a playback index
screen appears on the monitor.
[SYSTEM SELECT] : For selecting the vertical
resolution.
CAM / MEDIA
[REC MODE]
: For selecting the frame rate.
1 . Set to the video playback mode.
2 . Select the video/still picture mode.
The playback index screen appears.
The way of operation differs according to the mode.
Ⅵ Selecting a file to play back in two ways
Still picture mode h Turn the POWER/MODE switch to
Select a playback file from the playback index screen.
Select a playback file from the date search screen.
(A Page 45)
video mode
MODE.
Video mode h still
Turn the POWER/MODE switch to
picture mode
MODE and hold for about 1 second.
Playing Back Videos from the Playback
Index Screen
● The thumbnails of the files that can be played back using
the current video format are displayed.
● The thumbnail for the group of files that cannot be played
back is displayed on the last page.
Video Indicating Lamp
● Split files are files that are automatically split when the
size exceeds 4 GB. All split files are stored under this
thumbnail.
Still Picture Indicating Lamp
ACCESS
IRIS
Cursor
(Selected thumbnail)
INDEX
T
FILE FORMAT
SHUTTER
Current Page/
Total Pages
AE
REC
W
Mode
Split Files
REC
CAM MEDIA
/
DC
VIDEO
1/10
USERS
DISPLAY
Q.REVIEW
MENU
CAM/MEDIA
POWER/MODE Switch
When in the video mode
?
● The video indicating lamp lights up.
● A video icon appears at the top of the screen.
INDEX
SELECT SET
SORT
Slot Used
Files that are not
supported
REC MODE (Frame rate)
When in the still picture mode
SYSTEM SELECT (Vertical resolution)
● The still picture indicating lamp lights up.
● A still picture icon appears at the top of the
screen.
VIDEO
10/10
Memo :
● If the [SYSTEM SELECT] menu is set to [720-**], switching
between the video/still picture mode reboots the
camcorder.
OTHERS
SELECT SET INDEX SORT
Files not playable using the current video format
43
Playback
During Forward Search (N)
B Push to the right The search speed changes each time
Playing Videos on the SD
Card (continued)
this is pushed. (3 steps)
C Push to the left The search speed goes back by 1 step.
D Push upward
Plays from the beginning of the file
E Push downward Plays from the beginning of the next file
1 . Select a file.
Press center
Playback
Push the Set Lever up/down or to the left/right to move the
cursor to the thumbnail you want to play.
During Reverse Search (O)
B Push to the right The search speed goes back by 1 step.
C Push to the left The search speed changes each time
this is pushed. (3 steps)
Memo :
● You can move to files under the next or previous date by
pressing the + or – button on the remote control.
D Push upward
E Push downward Plays from the beginning of the next file
Press center Playback
Plays from the beginning of the file
2 . Play the file.
Press the center of the Set Lever.
● The selected video file is played back.
During Slow Forward Playback (WI)
B Push to the right Playback
C Push to the left Still
D Push upward Switches to the still mode at the
beginning of the file
Changing the mode during video playback
E Push downward Switches to the still mode at the
beginning of the next file
To change the mode during playback, operate using the Set
Lever.
Press center
Still
During Slow Reverse Playback (HW)
B Push to the right Still
C Push to the left Reverse playback
D Push upward Switches to the still mode at the
beginning of the file
During Playback (I)
B Push to the right Forward Search
The speed changes each time this is
pushed. (3 steps)
E Push downward Switches to the still mode at the
C Push to the left Reverse Search
The speed changes each time this is
pushed. (3 steps)
beginning of the next file
Press center
Still
D Push upward
Plays from the beginning of the file
Memo :
● Files on the SD cards in slots A, B are played back
continuously when [SLOT AUTO SWITCHING] in the
[CAMERA SETTINGS] menu is set to [ON].
● When frame-by-frame reverse playback is performed,
some frames may be missed.
E Push downward Plays from the beginning of the next file
Press center
Still
During Still Mode (W)
B Push to the right Forwards frame by frame
Ⅵ Returning to the index screen from the
C Push to the left Reverses frame by frame
respective modes
B Push to the right Slow forward playback
for 1 second or
longer
Press the INDEX button.
INDEX
C Push to the left Slow reverse playback
for 1 second or
longer
Memo :
● You can display still images from the index screen or
restore the index screen using the zoom lever.
When the index screen is displayed, press (T) of the zoom
lever to display the still image.
D Push upward
Switches to the still mode at the
beginning of the file
E Push downward Switches to the still mode at the
When a still image is displayed, press (W) of the zoom
lever to return to the index screen.
beginning of the next file
Press center
Playback
44
4 . Play the file.
Selecting a File on the Date Search Screen
Press the center of the Set Lever or (T) of the zoom lever.
● The selected video file is played back.
Press the INDEX button when the playback index screen is
displayed.
● The date search screen appears.
INDEX
Ⅵ Returning to the playback index screen
Press the INDEX button when the date search screen or
date index screen is displayed.
A list of dates based on the date of the selected file on the
playback index screen is displayed.
The list displays files up to a maximum of 6 days.
INDEX
Oldest date in the playback index list
SEARCH DATE
JAN. 01. 2009
JAN. 02. 2009
JAN. 03. 2009
JAN. 04. 2009
JAN. 05. 2009
JAN. 06. 2009
1/1
SELECT SET INDEX SORT
Cursor (Date of the selected file)
1 . Select a date.
Push the Set Lever up or down.
2 . Confirm the date.
Press the center of the Set Lever or (T) of the zoom lever.
● An index screen for the selected date is displayed.
JAN. 02. 2009
1/1
SELECT SET INDEX SORT
3 . Select a file to play.
Push the Set Lever up/down or to the left/right to move the
cursor to the thumbnail you want to play.
45
Playback
Playing Videos on the SD
Card (continued)
Capturing a Still Picture in the Still Mode
1 . Set to the still mode.
2 . Press SNAPSHOT all the way down.
● The still picture is captured and saved to the SD card.
(Still picture file)
You can confirm the capture operation by the shutter
sound generated when the SNAPSHOT button is pressed
if you set [OPERATION SOUND] in the [CAMERA
SETTINGS] menu to [ON].
Viewing Video File Information
1 . Select the file to view information when the index
screen is displayed.
Or
Set to the still mode during video playback.
SNAP
SHOT
2 . Press the DISPLAY button.
Memo :
● It takes about 3 seconds to capture a still picture.
● The size of the captured image is 1920 x 1080.
● When the [SYSTEM SELECT] menu is set to [720-**], still
pictures cannot be captured.
● The file information is displayed.
DISPLAY
AUTO MANUAL
SNAPSHOT
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
-
LINE
MIC
-
AUDIO
SELECT
INPUT1
INPUT2
-
-
MIC+48V
INPUT1
INPUT2
AUTO MANUAL
USER1 USER2
CAM / MEDIA
ND
USERS
FILTER
ON
FOCUS
ZOOM
CAM MEDIA
/
DISPLAY
Q.REVIEW
MENU
USERS
DISPLAY
Q.REVIEW
MENU
OFF
AF/MF
FULL AUTO
COMPONENT
OUT
A
/
V
OUT
GAIN WHT.BAL
A
/
B
L-
B-
M-
H-
A-
DISPLAY
P
R
S
T-
A
B
FILE, DATE/TIME, START TC, END TC,
DURATION, REC MODE, OK MARK
3 . To clear the file information display, press the
DISPLAY button.
● Returns to the index screen or still image display.
46
Enlarging a Still Image
Adjusting the Volume of the Built-In
Speaker or Headphone
Make use of the remote control.
Audio sound is not output from the built-in speaker if a
headphone, the A/V OUT terminal, or HDMI terminal is
connected.
Memo :
● This function is not available on the camcorder unit.
● To use the remote control, set [REMOTE] in the [CAMERA
SETTINGS] menu to [ON].
Ⅵ When using a headphone
Connect the headphone to the headphone (
) jack.
1 . Set to the still mode during the video playback
mode.
When in the still picture playback mode, display the
still picture on the full screen.
2 . Press zoom (T) on the remote control.
● The image is enlarged and a sub screen appears at the
bottom right corner.
● The original image is shown on the sub screen.
● The image is enlarged based on the position of the
viewpoint. Moving the viewpoint also moves the main
screen.
Headphone Jack
Ⅵ Adjusting the audio level of the built-in speaker
or headphone
Turn the ADJ./VOL. knob.
ACCESS
IRIS
SHUTTER
OPEN
AE
±
REC
CLOSE
Sub
Screen
ADJ./VOL.
Knob
DC
Viewpoint
3 . Press zoom (T) on the remote control to enlarge the
image.
4 . Move the viewpoint.
Press the cross-shaped buttons on the remote control to
move the viewpoint.
5 . Press zoom (W) on the remote control to reduce the
image. (Zoom-out)
Zooming out continuously restores the image to its
original size. The sub screen also disappears.
Zoom
SET
Cross-shaped
Buttons
47
Playback
Playing Still Pictures on
the SD Card
Viewing Still Pictures in a Slideshow
This feature enables still pictures to be played back serially
on the screen when in the still picture playback mode.
Play a still picture.
Preparation: Insert an SD card, and select the card slot.
1 . Start the slideshow.
Press the center of the Set Lever.
1 . Set to the still picture playback mode. (A Page 43)
● The next picture slides in from the right. (Forward
direction)
● The still picture index screen appears.
Cursor (Selected thumbnail)
Current Page/Total Pages
IMAGE
1/1000
Ⅵ Reversing the display order of the slides
Push the Set Lever upward.
● The previous picture slides in from the left.
?
SELECT SET INDEX SORT
Ⅵ Restoring the display order of the slides
Push the Set Lever downward.
Card Slot
Files that are not supported
2 . Select a file.
Push the Set Lever up/down or to the left/right to move the
cursor to the thumbnail you want to play.
2 . End the slideshow.
Press the center of the Set Lever.
● Returns to the full screen display of a still picture.
Memo :
● You can move to files under the next or previous date by
pressing the + or – button on the remote control.
Memo :
● Files on the SD cards in slots A, B are played back
continuously when [SLOT AUTO SWITCHING] in the
[CAMERA SETTINGS] menu is set to [ON].
3 . Play the file.
Press the center of the Set Lever or (T) of the zoom lever.
● The selected video file is played back.
Returning to the Still Picture Index Screen
Press the INDEX key or (W) of the zoom lever.
Ⅵ Displaying the next/previous still picture
Displaying the next still picture
INDEX
Push the Set Lever to the right.
Selecting a File on the Date Search Screen
Returning to the previous still picture
Push the Set Lever to the left.
1 . Press the INDEX button when the still picture index
screen is displayed.
● The date search screen appears.
INDEX
ASelecting a File on the Date Search ScreenB(A Page 45)
48
Viewing Still Picture File Information
1 . Select the file to view information when the index
screen is displayed.
Or
IRIS
COMPONENT
SHUTTER
AE
Display the relevant still picture.
REC
OUT
A/V OUT
HDMI
2 . Press the DISPLAY button.
DC
● The file information is displayed.
DISPLAY
Component
Cable
AUTO MANUAL
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
-
LINE
MIC
-
AUDIO
SELECT
HDMI Cable
(Optional)
INPUT1
INPUT2
AV Cord
-
-
MIC+48V
INPUT1
INPUT2
AUTO MANUAL
USER1 USER2
CAM / MEDIA
ND
USERS
FILTER
ON
FOCUS
ZOOM
CAM MEDIA
/
DISPLAY
Q.REVIEW
MENU
USERS
T1
DISPLAY
Q.REVIEW
MENU
OFF
AF/MF
FULL AUTO
COMPONENT
OUT
A
/
V
OUT
GAIN WHT.BAL
A
/
B
L-
B-
M-
H-
A-
DISPLAY
P
R
S
T-
A
B
FILE, FOLDER, DATE/TIME, SIZE, QUALITY, OK MARK
HDMI
Component
Video Input
AV Input
3 . To clear the file information display, press the
DISPLAY button.
● Returns to the index screen or still picture display.
T1 When the component terminal is used, the video terminal
of the AV cord will not be used.
Enlarging a Still Picture
Ⅵ Output is as follows when two or more terminals
You can enlarge the display of a still picture using the zoom
buttons on the remote control.
AEnlarging a Still ImageB(A Page 47)
are connected at the same time.
● The HDMI terminal always outputs video and audio
sound.
● When both the COMPONENT OUT and A/V OUT
terminals are connected, video is output from the
COMPONENT OUT terminal, while audio sound is output
from the A/V OUT terminal.
Viewing Videos on a
Monitor
● When both the HDMI and COMPONENT OUT terminals
are connected, the signal selected in the [HDMI OUTPUT]
menu instead of the analog component signal set in the
menu is output from the COMPONENT OUT terminal.
Applicable to: Video shooting mode, video playback mode
● When both the HDMI and A/V OUT terminals are
connected, video is output from the HDMI terminal, and
audio sound is output from both terminals.
There are three video output terminals on this camcorder.
Choose the most suitable terminal according to the monitor
in use.
Memo :
● Be sure to use the supplied component cable.
● You can specify the following items in the [CONNECTION
SETTINGS] menu.
A/V OUT
terminal
:
:
Outputs composite video and audio signals.
COMPONENT
OUT terminal
[VIDEO OUTPUT]: For adjusting the display size on the
monitor. (4:3 or 16:9)
[DISPLAY ON TV]: For specifying whether to enable on-
screen display.
● When the HDMI, COMPONENT OUT or A/V OUT terminal
is connected, video images will not appear on the
viewfinder.
sound is not output. Set the resolution in
[COMPONENT OUTPUT] of the
[CONNECTION SETTINGS] menu.
(A Page 63)
HDMI terminal
:
Outputs HDMI signals. Configure the settings
in the [CONNECTION SETTINGS] menu to
match the monitor to be connected. [HDMI
OUTPUT], [HDMI COLOR SETTING], [HDMI
ENHANCE SETTING] (A Page 63)
49
Editing Files
Enabling/Disabling File
Protection
Specifying Selected Files
1 . Select [FILE SELECT] in the [OK MARK] menu, and
press the center of the Set Lever.
● The OK MARK selection screen appears.
OK Mark
Applicable to: Video playback mode, still picture playback
mode
OK MARK
1/10
You can enable or disable the file protection feature, which
helps to prevent a video or still picture file from being
deleted. The file protection feature is indicated on the
camcorder as follows.
Enable protection
Disable protection
: “Append OK mark”
: “Delete OK mark”
SELECT SET MENU QUIT
2 . Select the files to append or delete the OK mark.
There are four ways to append/delete the OK mark.
● Specify files individually
Push the Set Lever up/down or to the left/right to select a file.
● Specify selected files
● Append to all files
Press the center of the Set Lever.
● Delete from all files
Preparation
● An OK mark is appended to or deleted from the selected
file.
Ⅵ Insert an SD card.
Ⅵ Set to the video or still picture playback mode.
Set the OK mark in the [OK MARK] menu.
[OK MARK]: (A Page 69)
You can repeat the above steps to select multiple files.
Memo :
3 . Press the MENU button.
● Files in the Others group cannot be specified.
● A confirmation screen appears.
MENU
Specifying Files Individually
4 . Select [YES] to execute.
1 . Select the file to append or delete the OK mark on
Push the Set Lever up or down to select [YES].
the index screen.
Press the center of the Set Lever.
● Files that are protected are indicated by an OK mark.
● Execution starts. Returns to the index screen or full
screen display at the end of the process.
2 . Select [CURRENT] in the [OK MARK] menu, and
press the center of the Set Lever.
● A confirmation screen appears.
ADD OK MARK?
(ADD PROTECTION)
YES
NO
SELECT SET
QUIT
MENU
T Push the Set Lever to the left or right to move to the next
or previous file.
3 . Select [YES] to execute.
Push the Set Lever up or down to select [YES].
Press the center of the Set Lever.
● Execution starts. A message appears at the end of the
process.
4 . Press the center of the Set Lever.
● Returns to the [OK MARK] menu screen.
50
2 . Select [CURRENT] in the [DELETE] menu, and
Appending To or Deleting From All Files
press the center of the Set Lever.
1 . Select [MARK ALL] or [DELETE ALL] in the [OK
Alternatively, press the USER button that is set as [DELETE].
MARK] menu, and press the center of the Set Lever.
● A screen to confirm deletion appears.
● A confirmation screen appears.
DELETE?
(REMAINING SCENES: 0009)
2 . Select [YES] to execute.
YES
NO
Push the Set Lever up or down to select [YES].
Press the center of the Set Lever.
SELECT SET
QUIT
MENU
● Execution starts. A message appears at the end of the
process.
T Push the Set Lever to the left or right to move to the next
or previous file.
3 . Select [YES] to execute.
Push the Set Lever up or down to select [YES].
Press the center of the Set Lever.
3 . Press the center of the Set Lever.
● Returns to the [OK MARK] menu screen.
● The file is deleted.
Deleting Files
Ⅵ Returns to the index screen if there are no remaining files.
Ⅵ The screen to confirm deletion appears if there are
remaining files.
To delete the file that is displayed, select [YES].
To return to the menu screen, select [NO].
To return to the index screen or full screen display, press
the [MENU] button.
Applicable to: Video playback mode, still picture playback
mode
There are three ways to delete unwanted video and still
picture files.
● Delete files individually
● Delete selected files
● Delete all files
Deleting Selected Files
1 . Select [FILE SELECT] in the [DELETE] menu, and
press the center of the Set Lever.
Preparation
● A screen for selecting files to delete appears.
Ⅵ Insert an SD card.
Ⅵ Set to the video or still picture playback mode.
Set [USER1], [USER2], or [USER3] in the [CAMERA
SETTINGS] menu to [DELETE], then press the
corresponding USER button.
Deletion Icon
VIDEO DELETE
1/10
[DELETE]: (A Page 69)
Memo :
OK
● Files appended with the OK mark and files in the Other
group cannot be deleted.
SELECT SET MENU QUIT
2 . Select the files to delete.
Deleting Files Individually
Push the Set Lever up/down or to the left/right to select a file.
1 . Select the file to delete from the index screen.
Alternatively, set to the still mode during video
playback.
Press the center of the Set Lever, or the USER button that is
set as [DELETE].
When in still picture playback, set to the full display
of a single image. (End slideshow)
● The selected file is indicated with a deletion icon.
You can repeat the above steps to select multiple files.
51
Editing Files
Deleting Files (continued)
Copying/Moving Files
3 . Press the MENU button.
Applicable to: Video playback mode (copy only), still picture
playback mode
A screen to confirm deletion appears.
MENU
You can copy or move files between Slot A and Slot B.
Only still picture files can be moved.
4 . Select [EXECUTE AND QUIT] to execute.
Preparation
Push the Set Lever up or down to select [EXECUTE AND
QUIT].
Ⅵ Insert SD cards into Slot A and Slot B.
Press the center of the Set Lever.
Insert an SD card containing the file to copy/move, and an
SD card where the file is to be copied/moved to.
● Deletion starts. A message appears at the end of the
process.
Ⅵ Select a playback mode.
● To copy a file, set to the video playback or still picture
playback mode according to the format of the file to be
copied.
5 . Press the center of the Set Lever.
● To move a file, set to the still picture playback mode.
● Returns to the index screen or full screen display.
following menus.
Copying files
Moving files
: [COPY] menu
: [MOVE] menu
[COPY], [MOVE]: (A Page 69)
Deleting All Files
Copying Files
1 . Select [DELETE ALL] in the [DELETE] menu, and
press the center of the Set Lever.
1 . Select the [COPY] menu, and press the center of the
● A screen to confirm deletion appears.
Set Lever.
● The copy settings screen appears.
2 . Select [YES] to execute.
Push the Set Lever up or down to select [YES].
SD AɨSD B
SD BɨSD A
Video
SCENE
Press the center of the Set Lever.
Still Picture
ALL
FILE
ꢀ
COPY
● Deletion starts. A message appears at the end of the
SD AɨSD B
MEDIA
FILE UNIT
process.
ALL
0059
EXECUTE
CANCEL
3 . Press the center of the Set Lever.
NO. OF FILES
● Returns to the index screen or full screen display.
SELECT SET MENU QUIT
[MEDIA] : For selecting the copy source and
destination
[FILE UNIT] : For selecting [ALL], or [SCENE]
(for videos) / [FILE] (for still pictures).
Memo :
● When copying videos, make use of a recommended SDHC
card (Class 6 or higher) as the destination.
52
2 . Specify [MEDIA] and [FILE UNIT].
COPY
Push the Set Lever up or down to select an item.
Push the Set Lever to the left or right to select a setting
value.
SD AɨSD B
MEDIA
FILE
FILE UNIT
0059
EXECUTE
CANCEL
NO. OF FILES
Ⅵ When [FILE UNIT] is set to [SCENE] (for videos) or [FILE]
(for still pictures)
SELECT SET
QUIT
MENU
Press the center of the Set Lever to display the screen for
selecting the files to copy. (See below)
Copy files by following step 3 . onwards in the previous
section ACopying FilesB.
Moving Files
Ⅵ When [FILE UNIT] is set to [ALL]
Push the Set Lever up or down to select [EXECUTE].
(See step 3 .)
Select the [MOVE] menu. The procedure for moving files is
the same as that described in ACopying FilesB.
3 . Select [EXECUTE], and press the center of the Set
Lever.
● Copying starts. A message appears at the end of the
process.
4 . Press the center of the Set Lever.
● Returns to the playback index screen.
Selecting the files to copy
Selection Icon
COPY
1/10
SELECT SET MENU QUIT
1 . Select a file.
Push the Set Lever up/down or to the left/right to select a file.
Next, press the center of the Set Lever.
● The selected file is indicated with a selection icon.
You can repeat the above steps to select multiple files.
2 . Press the MENU button.
● Returns to the copy settings screen.
MENU
53
Other Features
Connecting to a Computer
Saving/Loading Settings
Applicable to: Video/still picture shooting modes, video/still
picture playback modes
Applicable to: Video/still picture shooting modes, video/still
picture playback modes
Files stored on the SD card can be retrieved to a PC by
connecting this camcorder to the PC using a USB cable.
The current settings of the camcorder can be saved to an SD
card.
The settings that are saved on the SD card can be reloaded
on the camcorder.
Memo :
● However, files cannot be written to the SD card from the
Up to four files can be saved on each SD card. (EXT1, EXT2,
EXT3, EXT4)
PC.
Ⅵ Settings that are saved
1 . Connect to a computer.
● Menu settings
Power of PC must be on
TSettings of the [FOCUS ASSIST] menu cannot be
saved.
● Settings controlled by the camcorder buttons
Shooting mode (AUTO/MANUAL), program AE mode,
shutter speed (AUTO/MANUAL), aperture (AUTO/
MANUAL), AE (AUTO/MANUAL), and focus (AUTO/
MANUAL)
ACCESS
IRIS
SHUTTER
OPEN
AE
±
REC
CLOSE
DC
USB Cable
Ⅵ Perform settings in the [CAMERA SETTINGS] menu.
USB
Terminal
ASetting Menu ScreensB: (A Page 65)
A Turn on the power of the camcorder and the PC.
Saving Settings to an SD Card
B If video recording is in progress, switch it to the stop
mode.
Select a file name (EXT1 to EXT4) to save settings to. The
subtitle of the file can be freely specified.
C Connect the USB cable.
● The USB mass storage menu is displayed.
Preparation
Insert an SD card.
Stop recording if it is in progress.
PLAYBACK ON PC
1 . Select [STORE FILE] in the [CAMERA SETTINGS]
menu, and press the center of the Set Lever.
● The [STORE FILE] screen appears.
PLAYBACK DATA ON PC
SET MENU QUIT
2 . Press the center of the Set Lever.
STORE FILE
FILE SELECT
SUB NAME
EXT1
SCENE
● The USB mass storage mode is enabled, and
communication starts.
UPDATE
CANCEL
PLAYBACK ON PC
SELECT SET MENU QUIT
Keyboard Screen
SUB NAME
SCENE
5/10
A
H
O
V
B
I
P
W
C
J
Q
X
D
E
L
S
Z
F
M
T
G
N
U
-
1
4
7
_
2
5
8
.
3
6
9
0
K
R
Y
@
Cancel
Clear
● The drives for Slot A and Slot B are displayed on the PC
screen.
SELECT SET MENU QUIT
Ⅵ Returns to the shooting or playback mode if the power of
the PC is turned off or the USB cable unplugged.
54
2 . Select the file to save settings to.
2 . Confirm the character.
Select [FILE SELECT], and push the Set Lever to the left or
Press the center of the Set Lever.
right to select a file name. (EXT1, EXT2, EXT3, EXT4)
● The selected character appears in the display area on the
screen. Repeat the above steps to enter subsequent
characters.
3 . To specify a subtitle, push the Set Lever up or down
to select [SUB NAME].
3 . Save the entered characters.
See ASpecifying a subtitleB below.
Push the Set Lever up/down or to the left/right to select the
ENTER key, then press the center of the Set Lever.
● Returns to the [STORE FILE] screen.
If you do not want to specify a subtitle, push the Set Lever
up or down to select [UPDATE].
4 . Select [UPDATE], and press the center of the Set
Lever.
Loading Settings from an SD Card
● The execution screen for saving the file is displayed. A
message appears at the end of the process.
Settings saved on an SD card can be loaded on the
camcorder. Select a file from EXT1 to EXT4.
Preparation
Insert an SD card.
Stop recording if it is in progress.
5 . Press the center of the Set Lever.
● Returns to the camera image or index screen.
1 . Select [LOAD FILE] in the [CAMERA SETTINGS]
Specifying a subtitle
menu, and press the center of the Set Lever.
You can specify a subtitle up to a maximum of 10 one-byte
characters. (Alphanumeric characters, @, -, _, .)
● The [LOAD FILE] screen appears.
Ⅵ When [SUB NAME] of the [STORE FILE] screen is
selected, press the center of the Set Lever to display the
keyboard screen.
LOAD FILE
No. of Input
Cursor
Character Display Area
EXT1
SCENE
Characters
FILE SELECT
SUB NAME
SUB NAME
SCENE
5/10
EXECUTE
CANCEL
A
H
O
V
B
I
P
W
C
J
Q
X
D
E
L
S
Z
F
M
T
G
N
U
-
1
4
7
_
2
5
8
.
3
6
9
0
K
R
Y
SELECT SET MENU QUIT
@
Cancel
Clear
2 . Select the file to load settings from.
Select [FILE SELECT], and push the Set Lever to the left or
SELECT SET MENU QUIT
right to select a file name. (EXT1, EXT2, EXT3, EXT4)
Moves cursor backward by one character
Moves cursor forward by one character
Clears one character
Clear
3 . Load the file.
Cancel
Closes the keyboard screen without saving
Push the Set Lever up or down to select [EXECUTE]. Next,
Closes the keyboard screen after saving (ENTER
key)
press the center of the Set Lever.
● Loading of the file starts. (A message is displayed while
the settings are being loaded.)
1 . Select a character.
● The camcorder reboots automatically after loading is
complete.
Push the Set Lever up/down or to the left/right to move the
cursor to the character you want to enter.
55
Other Features
Operation Sound and Tally
Settings
Restoring the Default
Settings
You can select whether to enable the operation sound as well
as illumination of the tally lamp.
You can reset the menu settings to their default values.
However, the time code/user’s bit, date/time, and hour meter
cannot be reset.
Operation sound
Set using [OPERATION SOUND] in the [CAMERA
SETTINGS] menu. (A Page 66)
When this is set to [ON], operation sound is output from the
built-in speaker.
1 . Select [RESET ALL MENU] in the [CAMERA
SETTINGS] menu.
2 . Press the center of the Set Lever.
If a headphone is connected, no operation sound will be
● The [RESET ALL MENU] screen appears.
Tally lamp
Set using [TALLY] in the [CAMERA SETTINGS] menu.
(A Page 66)
When this is set to [ON], the tally lamp lights up in the
recording mode.
RETURN SETTINGS TO
DEFAULT SETTINGS?
EXECUTE
CANCEL
Displaying the Hour Meter
SELECT SET MENU QUIT
3 . Restore the default settings.
Push the Set Lever up or down to select [EXECUTE].
Next, press the center of the Set Lever.
The hour meter displays the total time during which the
power of the camcorder is turned on.
● The menu screen closes, and the settings are reset to
their default values.
The camcorder reboots automatically if there are changes
in the [SYSTEM SELECT] menu.
1 . Select [HOUR METER] in the [DISPLAY SETTINGS]
menu. (A Page 65)
2 . Press the center of the Set Lever.
● The hour meter appears.
3 . Press the center of the Set Lever again.
● Returns to the menu screen.
56
Menu Screens
Setting Menu Screens
5 . Change the parameter.
Push the Set Lever up or down to select.
Next, press the center of the Set Lever.
● The settings are changed.
The settings are saved in the memory of the camcorder, and
will not be deleted even when the power of the camcorder is
turned off.
Ⅵ The menu screens in the second layer can also be
altered using the same procedure. Select a parameter
from the second layer’s menu, then press the center of
the Set Lever to return to the first layer’s menu.
Menu settings vary according to the operation mode.
Ⅵ To return to the first layer’s menu without changing
settings in the second layer’s menu, push the Set Lever
to the left.
1 . Set to the operation mode you want to configure.
(Video shooting/still picture shooting/video playback/still
picture playback modes)
6 . Exit the menu setting screen.
Press [MENU].
2 . Press [MENU].
MENU
● The menu screen appears.
MENU
Memo :
● The settings can be saved to an SD card. (A Page 54)
No display: A next layer is available
MENU
CAMERA PROCESS
FILE FORMAT
1080
SYSTEM SELECT
/
60 30
1920
REC MODE
CAMERA SETTINGS FOR REC
SET MENU QUIT
With display: A next layer is not available
Set Lever
MENU
Some menu items may come in two layers. The current
setting values are displayed on the right for items with only
one layer.
3 . Select an item.
Push the Set Lever up or down to move the focus to the item
you want to select.
4 . Display the parameters or the second layer’s menu.
Press the center or right side of the Set Lever.
Parameter
CAMERA PROCESS
FOCUS ASSIST
OFF
FOCU
ON
ZEBRA
DETAIL LEVEL
FOR EASY FOCUSING
RETURN SET MENU QUIT
Memo :
● A separate setting screen may appear for some menu
items.
57
Menu Screens
List of Valid Menu Items for
Each Operation Mode
Although the menu items below are displayed on the screen, some of them may not be available depending on the operation
mode.
⅜: Valid setting.
ן : Invalid setting. Operation Mode
Operation Mode
Video
Shooting
Still
Picture
Video
Playback
Still
Picture
Video
Shooting
Still
Picture
Video
Playback
Still
Picture
Menu Item
Menu Item
Shooting
Playback
Shooting
Playback
CAMERA PROCESS
AUDIO REF. LEVEL
MIC LEVEL SETTING
INTERNAL MIC LEVEL
AUDIO MONITOR
TC/UB
⅜
⅜
⅜
⅜
ן ן ן ן ן ן ן ן ן ן ן ן FOCUS ASSIST
⅜
⅜
⅜
⅜
ן ן ן ן FOCUS ASSIST
COLOR
ZEBRA
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
ן ן ן ן ן ן ן ן ן ן ן ⅜
ן ן ⅜
ן ן ן ⅜
ן ⅜
ן ן ן ן ⅜
⅜
⅜
ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן ן DETAIL LEVEL
DETAIL V/H BALANCE
KNEE
TC PRESET
⅜
⅜
⅜
⅜
⅜
ן ן ן ן ן ן ן ן ן ן ן ⅜
ן ן ן ן ן ן ן ⅜
⅜
⅜
ן ן ן ן ן ן ן ן ⅜
⅜
⅜
⅜
DROP FRAME
TC GENE.
GAMMA
UB PRESET
GAMMA LEVEL
COLOR MATRIX
COLOR GAIN
PRESET TEMP.
WHITE PAINT<R>
WHITE PAINT<B>
FAW
TC DISPLAY
SELF-TIMER
SHUTTER MODE
DELETE
⅜
ן ן ן ן OK MARK
COPY
MOVE
GAIN L
DISPLAY SETTINGS
LANGUAGE
GAIN M
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
GAIN H
CLOCK ADJUST
DATE DISPLAY STYLE
MONITOR BRIGHT
MONITOR BACKLIGHT
MIC LEVEL METER
HOUR METER
CAMERA SETTINGS
LOAD FILE
PHOTOMETRY AREA
COLOR BAR
TELE MACRO
FILE FORMAT
SYSTEM SELECT
REC MODE
CLIP CONTINUOUS REC
IMAGE QUALITY
IMAGE SIZE
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
STORE FILE
USER1
GAIN UP
USER2
CONNECTION SETTINGS
DISPLAY ON TV
VIDEO OUTPUT
COMPONENT OUTPUT
HDMI OUTPUT
HDMI COLOR SETTING
USER3
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
SLOT AUTO
SWITCHING
RESET ALL MENU
AUTO POWER OFF
OIS
⅜
⅜
⅜
⅜
⅜
⅜
⅜
ן ⅜
⅜
⅜
⅜
⅜
⅜
⅜
ן ⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
HDMI ENHANCE
SETTING
TALLY
REMOTE
MEDIA SETTINGS
FORMAT
OPERATION SOUND
PRIORITY SETTING
ON-SCREEN DISPLAY
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
⅜
VIDEO NO. RESET
IMAGE NO. RESET
WIND CUT
INPUT1
⅜
⅜
⅜
ן ן ן ן ן ן ן ן ן INPUT2
MIC
58
Menu Screens of the Video
Shooting Mode
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
For setting the camera operation and image quality during shooting.
FOCUS ASSIST
For selecting whether to add color to the contour of the focused image upon switching the image to
black-and-white. (Focus Assist function)
R OFF : Disables the function.
ON : Enables the function.
FOCUS ASSIST
For setting the color of the focused area when the Focus Assist function is enabled.
COLOR
R RED
GREEN
BLUE
ZEBRA
For selecting whether to display zebra patterns at the bright areas of the subject. The brightness of
the zebra pattern display can also be specified.
R OFF
: Zebra pattern is displayed.
ON
THRESHOLD : A separate screen is displayed.
The brightness of the zebra pattern display can be specified. (A Page 34)
DETAIL LEVEL
A separate screen is displayed. (A Page 39)
Use this item to adjust the contour (detail) sharpness level.
Decrease the number : Softens the contour.
OFF
: Disables the function.
OFF, MIN (-10), -9 to RNORMAL (0) to +9, MAX (10)
DETAIL V/H
BALANCE
A separate screen is displayed. (A Page 39)
Use this item to sharpen contours (details) in the horizontal (H) direction or in the vertical (V)
direction.
Increase the number : Enhances contour in the horizontal direction.
Decrease the number : Enhances contour in the vertical direction.
MIN (-5), -4 to RNORMAL (0) to +4, MAX (5)
KNEE
For setting whether to run the “knee” function, which compresses video signals that exceed a
certain level to render the tonality in the highlighted area, automatically or to specify the knee point
(starting point of compression) manually.
R AUTO
100%, 95%, 90%, 85%
: Adjusts automatically.
: Runs “knee” function at the specified point.
GAMMA
OFF
: No gamma curve correction.
R STANDARD
CINEMA
: Normal gamma curve.
: Appears movie-like when viewing on a TV screen.
GAMMA LEVEL
A separate screen is displayed. (A Page 39)
When [STANDARD] or [CINEMA] is set for the GAMMA item, a gamma curve can be set
individually.
Increase the number : Enhances the tonality of the black. However, the tonality in the bright
areas deteriorates.
Decrease the number : Enhances the tonality in the bright areas. However, the tonality in the
black areas deteriorates.
MIN (-5), -4 to RNORMAL (0) to +4, MAX (5)
59
Menu Screens
Menu Screens of the Video
Shooting Mode (continued)
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
COLOR MATRIX
For setting the COLOR MATRIX.
OFF
R STANDARD
CINEMA VIVID COLOR
: Sets a normal color matrix.
: Sets to a vivid cinema color.
CINEMA SUBDUED COLOR : Sets to a subdued cinema color.
COLOR GAIN
A separate screen is displayed. (A Page 39)
Use this item to adjust the video signal color level.
OFF
: Sets the video to black and white.
Increase the number : Makes the colors more dense.
Decrease the number : Makes the colors less dense.
OFF, MIN (-5), -4 to RNORMAL (0) to +4, MAX (5)
PRESET TEMP.
For setting the basic color temperature when the WHT.BAL. switch is in the PRST(PRESET)
position.
R 3200K : Sets the basic color temperature to 3200K. (Use for light sources with a low color
temperature, such as halogen lamps.)
5600K
: Sets the basic color temperature to 5600K. (Use for light sources with a high color
temperature, such as sunlight.)
Memo :
● This item does not function when [FAW] is set to [PRESET].
WHITE PAINT<R>
A separate screen is displayed. (A Page 36)
Use this item to adjust the R (red) component when in the AWB (Auto White Balance) mode.
Increase the number : Strengthens the red.
Decrease the number : Weakens the red.
MIN (-15), -14 to R0 to 14, MAX (15)
Memo :
● This item is available when the WHT.BAL. switch is set to A or B. Settings can be made for A, B
● When you press the AWB (Auto White Balance) button and readjust the white balance, [WHITE
PAINT<R>] becomes “0”.
WHITE PAINT<B>
A separate screen is displayed. (A Page 36)
Use this item to adjust the B (blue) component when in the AWB (Auto White Balance) mode.
Increase the number : Strengthens the blue.
Decrease the number : Weakens the blue.
MIN (-15), -14 to R0 to 14, MAX (15)
Memo :
● This item is available when the WHT.BAL. switch is set to A or B. Settings can be made for A, B
individually. (When PRESET is set, this cannot be selected.)
● When you press the AWB (Auto White Balance) button and readjust the white balance, [WHITE
PAINT<B>] becomes “0”.
FAW
For setting the positions to assign the FAW (Full Auto White Balance) function to the WHT.BAL.
switch. (Fixed at FAW when in FULL AUTO mode A)
R NONE
: The FAW function is not assigned.
: Assigns FAW to the A position.
: Assigns FAW to the B position.
: Assigns FAW to the PRESET position.
A
B
PRESET
60
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
GAIN L
GAIN M
GAIN H
For setting the gain value for each position on the GAIN switch.
(Fixed at AGC when in FULL AUTO mode A)
0dB
3dB
6dB
9dB
12dB
15dB
18dB
AGC
<Factory settings>
GAIN L:0db GAIN M:9 dB GAIN H:18 dB
PHOTOMETRY AREA For setting the area for brightness correction.
R WHOLE SCREEN: Sets the entire screen as the photometry area.
SPOT
: A separate screen is displayed. (A Page 38)
Specify the photometry area.
COLOR BAR
TELE MACRO
FILE FORMAT
For setting whether to output color bars. (Fixed at [OFF] when in FULL AUTO mode A)
R OFF : Color bars are not output.
ON : Color bars are output.
For selecting whether to shorten the closeup distance at the tele (T) end of the zoom lens.
R OFF : Enables closeup shots up to about 1 m.
ON : Enables closeup shots up to about 80 cm.
For setting the video file format.
R QuickTime file format : Records in the QuickTime(MOV) format.
MP4 file format
: Records in the MP4 file format.
Memo :
● The display color of the recording mode icon on the status screen changes according to the
settings in the [FILE FORMAT] menu.
When set to [QuickTime file format] : Blue
When set to [MP4 file format]
: Orange
SYSTEM SELECT
For setting the system of this camcorder.
R 1080-60/30 : Vertical resolution of 1080 lines, frame rate of 60/30
720-60/30 : Vertical resolution of 720 lines, frame rate of 60/30
1080-50/25 : Vertical resolution of 1080 lines, frame rate of 50/25
720-50/25 : Vertical resolution of 720 lines, frame rate of 50/25
1080-24
720-24
: Vertical resolution of 1080 lines, frame rate of 24
: Vertical resolution of 720 lines, frame rate of 24
Memo :
● When the setting of this item is altered, the camcorder will reboot (restart) automatically.
61
Menu Screens
Menu Screens of the Video
Shooting Mode (continued)
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
REC MODE
For setting the recording mode.
The following settings can be selected according to the [SYSTEM SELECT] menu item settings.
SYSTEM
Settings for this Item
Description
SELECT
1080-60/30 R 1920/60i(HQ)
1440/60i(HQ)
Horizontal resolution of 1920 lines, 60 field interlace, fine quality
Horizontal resolution of 1440 lines, 60 field interlace, fine quality
Horizontal resolution of 1440 lines, 60 field interlace, standard
quality
1440/60i(SP)
1920/30p(HQ)
Horizontal resolution of 1920 lines, 30 frame progressive, fine
quality
720-60/30
1280/60p(HQ)
1280/60p(SP)
1280/30p(HQ)
1280/30p(SP)
Horizontal resolution of 1280 lines, 60 frame progressive, fine
quality
Horizontal resolution of 1280 lines, 60 frame progressive, standard
quality
Horizontal resolution of 1280 lines, 30 frame progressive, fine
quality
Horizontal resolution of 1280 lines, 30 frame progressive, standard
quality
1080-50/25
720-50/25
1920/50i(HQ)
1440/50i(HQ)
1440/50i(SP)
Horizontal resolution of 1920 lines, 50 field interlace, fine quality
Horizontal resolution of 1440 lines, 50 field interlace, fine quality
Horizontal resolution of 1440 lines, 50 field interlace, standard
quality
Horizontal resolution of 1920 lines, 25 frame progressive, fine
quality
1920/25p(HQ)
1280/50p(HQ)
1280/50p(SP)
1280/25p(HQ)
1280/25p(SP)
Horizontal resolution of 1280 lines, 50 frame progressive, fine
quality
Horizontal resolution of 1280 lines, 50 frame progressive, standard
quality
Horizontal resolution of 1280 lines, 25 frame progressive, fine
quality
Horizontal resolution of 1280 lines, 25 frame progressive, standard
quality
720-24
1280/24p(HQ)
Horizontal resolution of 1280 lines, 24 frame progressive, fine
quality
1280/24p(SP)
Horizontal resolution of 1280 lines, 24 frame progressive, standard
quality
Memo :
● [REC MODE] cannot be set if the [SYSTEM SELECT] menu is set to [1080-24].
(Fixed at 1920/24p(HQ).)
● When the [FILE FORMAT] menu is set to [MP4 file format], [1440/60i(HQ)] and [1440/50i(HQ)]
are not displayed.
CLIP CONTINUOUS REC For selecting whether to record multiple clips as a continuous file.
R OFF : Disables continuous clip recording.
ON : Enables continuous clip recording.
62
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
For setting connections with external devices.
DISPLAY ON TV
For specifying whether to enable on-screen display on the monitor.
R OFF : Disables on-screen display.
ON : Enables on-screen display.
VIDEO OUTPUT
For selecting the monitor type.
4:3
: When connecting to a conventional monitor (4:3)
R 16:9
: When connecting to a wide monitor (16:9)
COMPONENT
OUTPUT
For selecting the resolution of video output from the component terminal to match the connected
monitor.
R 480i
720p
: When connecting to a monitor that supports 480i and 480p
: When connecting to a monitor that supports 720p
: When connecting to a monitor that supports 1080i
1080i
This setting is fixed at 576i when 1080-50/25 or 720-50/25 is selected for SYSTEM SELECT.
HDMI OUTPUT
For selecting the resolution of video output from the HDMI terminal to match the connected
monitor.
Set this item when images are not properly displayed on a monitor that supports a maximum
output of 1080i.
R AUTO : Use this setting under normal circumstances. Resolution is automatically set
according to the connected monitor.
480p
480i
: Outputs at 480p.
: Outputs at 480i.
This setting is fixed at 576p or 576i when 1080-50/25 or 720-50/25 is selected for SYSTEM
SELECT.
HDMI COLOR
For selecting the color format of HDMI signals.
SETTING
RAUTO
: Outputs upon detecting YUV/RGB automatically according to the connected
monitor.
RGB
: Outputs RGB signals.
HDMI ENHANCE
SETTING
For setting the color range of HDMI signals.
R OFF : When connected to a conventional monitor
ON : When connected to a PC monitor
For setting processes related to the SD card.
FORMAT
A separate screen is displayed. (A Page 24)
Erases all data.
VIDEO NO. RESET
IMAGE NO. RESET
A separate screen is displayed. (A Page 24)
Resets the video file number.
A separate screen is displayed. (A Page 24)
Resets the still picture file number.
For selecting whether to reduce wind noise from the microphone.
INPUT1
INPUT2
MIC
For selecting whether to reduce wind noise from the microphone connected to the INPUT1
terminal.
R OFF : Wind noise is not reduced.
ON : Reduces wind noise.
For selecting whether to reduce wind noise from the microphone connected to the INPUT2
terminal.
R OFF : Wind noise is not reduced.
ON : Reduces wind noise.
For selecting whether to reduce wind noise from the microphone connected to the MIC terminal
and the built-in microphone.
R OFF : Wind noise is not reduced.
ON : Reduces wind noise.
63
Menu Screens
Menu Screens of the Video
Shooting Mode (continued)
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
AUDIO REF. LEVEL
For setting the reference audio recording level.
R -20dB
-12dB
MIC LEVEL SETTING
INTERNAL MIC LEVEL
AUDIO MONITOR
For setting the input level of the microphone connected to the MIC terminal.
-2,-1,R0,+1,+2
For setting the input level of the built-in microphone.
-2,-1,R0,+1,+2
For setting the audio sound of the headphone.
R MIX
STEREO
: Outputs mixed sound.
: Outputs stereo sound.
For setting the time code or user’s bit.
TC PRESET
A separate screen is displayed. (A Page 42)
Use this item to preset the time code.
DROP FRAME
For setting the time code generator framing mode to drop-frame or non-drop-frame.
R DROP
: Internal time code generator works in drop-frame mode. Use this setting when
you want to place emphasis on the recording time.
NON DROP : Internal time code generator works in non-drop-frame mode. Use this setting
when you want to place emphasis on the number of frames.
Memo :
● This item can be specified only when [SYSTEM SELECT] is set to [1080-60/30] or [720-60/30]. It
is fixed at [NON DROP] when set to [720-24].
TC GENE.
For setting the time code generator to the preset mode or regeneration mode.
The run mode during the preset mode can also be selected.
FREE
: Enables the preset mode in the free-run mode. The time code operates in the run
mode at all times when preset to this position.
R REC
mode only during recording.
REGEN : Enables the regeneration mode. The time code on the SD card is read, and time
code is recorded in continuation of this value.
UB PRESET
A separate screen is displayed. (A Page 42)
Use this item to preset the user’s bit.
TC DISPLAY
For selecting whether to display the time code or user’s bit on the screen.
OFF : Both the time code and user’s bit are not displayed.
R TC
: Displays the time code.
: Displays the user’s bit.
UB
64
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
For setting screen displays.
LANGUAGE
For selecting a display language. (A Page 21)
CLOCK ADJUST
A separate screen is displayed. (A Page 21)
For setting the date and time.
DATE DISPLAY
A separate screen is displayed.
STYLE
For selecting the date and time display format (12h/24h).
MONITOR BRIGHT
A separate screen is displayed.
For adjusting the brightness of the viewfinder or LCD screen using a slide bar.
MONITOR
BACKLIGHT
For setting the brightness of the LCD screen backlight.
BRIGHTER : Brighter than the standard mode
R STANDARD : Standard brightness
AUTO
: Switches automatically to the bright mode when used outdoors, and to the
standard mode when used indoors.
MIC LEVEL METER
HOUR METER
For selecting whether to display the microphone level on the screen.
OFF : Microphone level is not displayed.
R ON : Microphone level is displayed.
A separate screen is displayed. (A Page 56)
For displaying the total time during which the power of the camcorder is turned on.
For setting the operation of this camcorder.
LOAD FILE
A separate screen is displayed. (A Page 55)
Use this item to load setting files saved on an SD card on the camcorder.
Select one of the four setting files from EXT1 to EXT4.
STORE FILE
A separate screen is displayed. (A Page 54)
A subtitle can be added to each file.
USER1
USER2
USER3
For assigning one of the following functions to each of the USER1, USER2, USER3 buttons.
FOCUS ASSIST
COLOR BAR
TC SETTING
TELE MACRO
: Displays the color bar. (A Page 39)
lens. (A Page 33)
Lolux
DELETE
ZEBRA
: Increases the sensitivity level at dark places. (A Page 32)
: Deletes unwanted files. (A Page 51)
: Displays zebra patterns at bright areas. (A Page 34)
CLIP CONTINUOUS OFF : Closes clips as a single file. (A Page 28)
NONE
: No function is assigned.
<Factory settings>
USER1
: Focus Assist
USER2
USER3
: Color Bar
: NONE
SLOT AUTO
SWITCHING
For selecting whether to switch between SD card slots A and B automatically.
OFF : Disables automatic switch.
R ON : Enables automatic switch.
65
Menu Screens
Menu Screens of the Video
Shooting Mode (continued)
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
RESET ALL MENU
A separate screen is displayed. (A Page 56)
Use this item to reset the menu and camcorder settings to their default values.
AUTO POWER OFF
For selecting whether to turn off the power automatically when the camcorder is not operated for
more than 5 minutes.
R OFF : Power does not turn off automatically.
ON : Power turns off automatically.
OIS
For selecting whether to use the image stabilizer feature.
OFF : Disables image stabilizer. Use this setting when the camcorder is secured, such as
when using a tripod.
R ON : Reduces blurring of images due to camera shake.
Memo :
● Correction by this feature may not be sufficient when camera shake is too strong.
TALLY
For selecting whether to turn on the tally lamp.
OFF : Turns off tally lamp.
R ON : Turns on tally lamp.
REMOTE
For selecting whether to accept remote control operation.
OFF : Does not accept remote control operation.
R ON : Accepts remote control operation.
OPERATION SOUND For selecting whether to turn on the operation sound when the operation buttons on the camcorder
are pressed.
R OFF : Turns off operation sound.
ON : Turns on operation sound.
PRIORITY SETTING
For selecting whether to show display on the LCD screen or viewfinder when both are turned on, or
R LCD MONITOR
: Displays on the LCD screen only.
: Displays on the viewfinder only.
VIEWFINDER
ALWAYS-ON VIEWFINDER : Displays on the viewfinder at all times.
AViewing the Viewfinder/LCD ScreenB: (A Page 22)
66
Menu Screens of the Still
Picture Shooting Mode
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
For setting the camera operation and image quality during shooting.
FOCUS ASSIST
For selecting whether to add color to the contour of the focused image upon switching the image to
black-and-white. (Focus Assist function)
R OFF : Disables the function.
ON : Enables the function.
FOCUS ASSIST
For setting the color of the focused area when the Focus Assist function is enabled.
COLOR
R RED
GREEN
BLUE
PHOTOMETRY AREA For setting the area for brightness correction.
R WHOLE SCREEN: Sets the entire screen as the photometry area.
SPOT
: A separate screen is displayed. (A Page 38)
Specify the photometry area.
PRESET TEMP.
For setting the basic color temperature when the WHT.BAL. switch is in the PRST(PRESET)
position.
R 3200K : Sets the basic color temperature to 3200K. (Use for light sources with a low color
temperature, such as halogen lamps.)
5600K
: Sets the basic color temperature to 5600K. (Use for light sources with a high color
temperature, such as sunlight.)
Memo :
● This item does not function when [FAW] is set to [PRESET].
FAW
For setting the positions to assign the FAW (Full Auto White Balance) function to the WHT.BAL.
switch. (Fixed at FAW when in FULL AUTO mode A)
R NONE
: The FAW function is not assigned.
: Assigns FAW to the A position.
: Assigns FAW to the B position.
: Assigns FAW to the PRESET position.
A
B
PRESET
TELE MACRO
For selecting whether to shorten the closeup distance at the tele (T) end of the zoom lens.
R OFF : Enables closeup shots up to about 1 m.
ON : Enables closeup shots up to about 80 cm.
IMAGE QUALITY
R FINE
STANDARD
: Fine (The number of possible shots decreases.)
: Standard (The number of possible shots increases.)
● This image quality setting is applied when still pictures are simultaneously recorded in the
video shooting mode. (A Page 28)
IMAGE SIZE
For selecting the size of still pictures.
R 1920x1080
1440x1080
1024x768
640x480
● The still picture size is set at 1920x1080 when still pictures are simultaneously recorded in the
video shooting mode. (A Page 28)
67
Picture Shooting Mode
(continued)
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
GAIN UP
For brightening the image electrically when shooting a dark subject.
OFF : Disables the function.
R AUTO : Adjusts automatically according to the surrounding brightness.
CONNECTION
Same as in video shooting mode. (A Page 63)
SETTINGS
MEDIA SETTINGS
Same as in video shooting mode. (A Page 63)
SELF-TIMER
For setting the timer.
R OFF
: Disables the self-timer.
2SEC : Takes a picture automatically 2 seconds after pressing the SNAPSHOT button. (Helps
to prevent camera shake.)
10SEC : Takes a picture automatically 10 seconds after pressing the SNAPSHOT button.
● To turn off the notification sound when shooting starts, set [OPERATION SOUND] of the
[CAMERA SETTINGS] menu to [OFF].
SHUTTER MODE
For selecting the shutter operation.
R RECORD ONE SHOT
: Disables continuous shooting.
CONTINUOUS SHOOTING : Continuous shooting is performed while the SNAPSHOT button is
pressed. (About 2 shots/second)
BRACKETING
: Performs three types of continuous shots starting from still
pictures at the brightness level that is automatically or manually
set, followed by slightly darker pictures (-0.3 EV) and slightly
brighter ones (+0.3 EV).
specified.
(A Page 29)
● The continuous shooting speed drops if the function is used continuously.
Same as in video shooting mode. (A Page 65)
DISPLAY SETTINGS
CAMERA SETTINGS
Same as in video shooting mode. (A Page 65)
68
Menu Screens of Video/
Still Picture Playback
Modes
Item
Description
) are common to all modes.
Items that are shaded (
Settings with the R mark are default values.
DELETE
A separate screen is displayed. (A Page 51)
For deleting video or still picture files.
CURRENT
: Deletes the currently selected video or still picture file.
FILE SELECT : Deletes selected video or still picture files collectively.
DELETE ALL
: Deletes all video or still picture files.
OK MARK
A separate screen is displayed. (A Page 50)
For setting whether to append an OK mark to or delete it from a video or still picture file.
Appending an OK mark helps to prevent a file from being deleted.
CURRENT
: Appends an OK mark to the currently selected video or still picture file, or
deletes the OK mark from the file.
OK mark from the file.
MARK ALL
DELETE ALL
: Appends an OK mark to all video or still picture files.
: Deletes the OK mark from all video or still picture files.
COPY
For copying video or still picture files to another SD card.
ALL
: Copies all video or still picture files.
: Copies selected video or still picture files.
SCENE (Video) / FILE (Still Picture)
pictures)
For moving still picture files to another SD card.
ALL
: Moves all still picture files.
FILE
: Moves selected still picture files.
DISPLAY SETTINGS
Same as in video shooting mode. (A Page 65)
Same as in video shooting mode. (A Page 65)
Same as in video shooting mode. (A Page 63)
CAMERA SETTINGS
CONNECTION
SETTINGS
MEDIA SETTINGS
Same as in video shooting mode. (A Page 63)
ON-SCREEN DISPLAY
For selecting the screen display during playback of videos or still pictures.
OFF
R DISPLAY ALL
: Hides display of all icons and the date and time.
: Displays all icons and the date and time.
DISPLAY DATE ONLY : Displays only the date and time.
DISPLAY DATE 5 SEC : Displays only the date and time for 5 seconds in the following cases:
● When playback starts
● When a file is changed during playback
● When the menu screen is closed
69
Others
Troubleshooting
Before sending for repair, check the camcorder’s problem according to the table below.
If the problem persists, consult our authorized dealers or JVC service center.
Symptom
Action
Page
● Check that the SD card is facing the right direction.
23
SD card cannot be
inserted.
● Connect the AC adapter correctly.
19
19
Power cannot be switched
on.
● Charge the battery.
● Use the CAM/MEDIA button to set to the camera shooting mode.
● Check the shooting mode with the video and still picture indicating lamps.
● Shooting stops automatically after 12 hours of continuous recording.
● Shooting may stop halfway due to the nature of the card.
25
25
-
Shooting cannot be
performed.
Shooting stops by itself.
Check whether the card is a recommended SD card (Class 6 or higher)
Erase the contents of the SD card (DELETE, FORMAT)
7
51, 63
-
● Clean any dirt or water droplets from the lens.
Focus is not adjusted
automatically.
● If you are shooting at a dark place or shooting a subject that has no contrast between
31
dark and light, adjust the focus manually.
● Use [Lolux].
32
33
37
The recorded subject is too
dark.
● Set exposure to the [+] side.
● For videos, set to the manual shooting mode and increase the sensitivity using the
GAIN switch.
● Set the GAIN switch to [AGC].
● For still pictures, set [GAIN UP] to [AUTO].
● Set to open up the aperture.
61
68
37
37
35
● Set to lower the shutter speed.
● Depending on the lighting conditions or when there are numerous light sources in the
background, set to the manual shooting mode and perform auto white balance
adjustment.
The color of the recorded
subject looks unnatural.
(Reddish, bluish, etc.)
● Adjust the red or blue using white paint adjustment.
36
● Do not use [TWILIGHT] from Program AE.
32
White balance cannot be
adjusted.
● The continuous shooting speed drops if the function is used continuously.
-
-
Continuous shooting speed
of still pictures is slow.
● Continuous shooting speed may drop depending on the SD card in use and or under
certain shooting conditions.
● Recording time may shorten depending on the environment, such as when shooting
fast-moving subjects.
-
The actual recording time is
shorter than the estimated
time.
● Set the FOCUS/ZOOM switch to FOCUS.
31
30
40
64
Focus knob of the lens
does not work.
● Set the FOCUS/ZOOM switch to ZOOM.
Zoom knob of the lens does
not work.
● Remove the audio unit cable from the AUDIO IN terminal of the camcorder.
The MIC terminal and built-
in microphone do not work.
● The recording level of the built-in microphone or microphone connected to the MIC
terminal cannot be adjusted using the recording level knob. (The recording level knob
can only be used for the INPUT1/INPUT2 terminal. Set the volume of the built-in
microphone or MIC terminal using the [INTERNAL MIC LEVEL] or [MIC LEVEL
SETTING] menu.)
Unable to adjust the
recording level of the built-
in microphone or
microphone connected to
the MIC terminal using the
recording level knob.
● When the RREC icon lights up in red or the RW icon lights up in yellow, it is not
28
Unable to switch to the
playback mode when
continuous clip recording is
paused.
possible to switch to the playback mode. To switch to the playback mode, close the clip
file.
70
Symptom
Action
Page
Screen appears dark or whitish.
● Adjust the angle and brightness of the screen.
● When used in cold places, the screen may appear darker.
22
-
● The screen may be reaching the end of its service life. Consult our authorized dealers
-
or JVC service center.
Screen display is difficult to see.
● The screen may be difficult to see if used in bright areas, such as under direct
sunlight.
-
-
Screen is blank.
● Operate the camcorder. (If the camcorder is not operated for a certain length of time
when the AC adapter is in use, the screen will turn off automatically to save energy.)
● Press the DISPLAY button.
● If the camcorder is in the still picture playback mode, set the [ON-SCREEN DISPLAY]
menu to [DISPLAY ALL] or [DISPLAY DATE ONLY].
15
69
The remaining battery power is
not correctly displayed.
● Charge the battery fully, use it up, and then charge again.
19
-
● If the camcorder is used for long periods of time in high or low temperatures, or if the
battery is repeatedly charged, the remaining battery level may not be displayed
correctly.
Screen display is uneven.
● If the screen or surrounding parts have been pressed, remove your hands and leave
the camera for a short while. (Applying pressure causes image unevenness.)
-
No display on the TV monitor.
● Set [DISPLAY ON TV] in the [CONNECTION SETTINGS] menu to [ON].
63
66
49
No display on the LCD screen or
viewfinder.
● Check the [PRIORITY SETTING] in the [CAMERA SETTINGS] menu.
● When the HDMI, COMPONENT OUT or A/V OUT terminal is connected, video
images will not appear on the viewfinder. Remove the cable.
Time code or user’s bit is not
displayed.
● Set [TC DISPLAY] in the [TC/UB] menu to [TC] or [UB].
64
28
Unable to switch from the
shooting mode to playback
mode.
● Check whether the pause mode of continuous clip recording is set. If it is, end the file
before switching the mode.
Sound or video is interrupted.
● Sometimes playback is interrupted at the connecting section between two scenes.
-
A part of the TV monitor screen
appears shaky.
● Set [HDMI OUTPUT] in the [CONNECTION SETTINGS] menu to [AUTO].
63
Images look unnatural on the TV
monitor screen. (long and thin,
etc.)
● Adjust [VIDEO OUTPUT] in the [CONNECTION SETTINGS] menu to match your TV
monitor.
63
Recorded videos cannot be
found on the index screen.
● Check the video file format or video format. (Adjust the [FILE FORMAT], [SYSTEM
SELECT], and [REC MODE] menu settings to match the video format to be played
back.)
61
62
The camcorder heats up.
● This is not a malfunction. (The camcorder may become warm when used for a long
time.)
-
20
-
The indicating lamp does not
blink during charging.
● Check the remaining battery power.
(The indicating lamp stops blinking when the battery is fully charged.)
● When charging the battery in a hot or cold environment, ensure that the temperature
is within the allowable operating temperature range. (Charging may stop to protect
the battery if the temperature is outside the allowable range.)
The camcorder operates slowly
when switching between video
and still picture modes or when
turning the power on or off.
● Copy the files on the SD card to a PC, and delete them from the SD card. (If there are
many still pictures (more than 1000 files) on the SD card, it takes time for the
camcorder to process the files.)
-
The remote control does not
work.
● Replace the battery.
● Set [REMOTE] in the [CAMERA SETTINGS] menu to [ON].
● The remote control may not function outdoors or under strong light conditions.
18
66
-
Ⅵ The following phenomena are not malfunctions.
Ⅵ Reset the camcorder when it does not function properly.
● The screen momentarily turns red or black when the sun
enters the field of view.
1 . Turn the power [OFF].
2 . Remove the battery and AC adapter from the
● Black dots, or shiny red, blue, or green spots appear on
the screen.
camcorder, reattach them, and turn on the power.
(The LCD screen contains 99.99 % or more effective pixels,
but 0.01 % or fewer pixels may be inactive or always lit.)
3 . Apply [RESET ALL MENU] in the [CAMERA
SETTINGS] menu.
71
Others
Warning Displays
Display
CHECK LENS COVER
SET DATE/TIME!
Action
Page
20
● Open the lens cover.
● Set the date and time.
21
-
● Using an AC adapter, charge the camcorder for over 24 hours, then set the
date and time.
19
COMMUNICATING ERROR
● Attach the battery again.
23
CANNOT USE IN VIDEO MODE
● Replace the SD card.
(Make use of an SDHC card (Class 6 or higher) when shooting videos.)
-
CANNOT USE IN STILL IMAGE
● You have pressed a button that does not function in the still picture shooting
MODE
mode.
-
● FORMAT ERROR!
● PLAYBACK FAILED
CANNOT RECORD
● Check the operating procedure, and perform the steps again.
● Turn off and on the power of the camcorder.
● Turn off and on the power of the camcorder.
20
● Shooting may not be possible due to the nature of the card.
Check whether the card is a recommended SD card (Class 6 or higher)
7
24, 51
Erase the contents of the SD card (DELETE, FORMAT)
● Turn off and on the power of the camcorder.
20
MEMORY CARD ERROR!
23
● Remove and re-insert the SD card. (SDXC cards are not supported.)
● Remove any dirt from the SD card terminals.
-
-
● Insert the SD card before turning on the power.
24, 63
● If the error is not resolved, back up the card and format it. (All data will be
erased.)
24, 63
NOT FORMATTED
● Select [OK] and then [YES] when [DO YOU WANT TO FORMAT?] appears.
29
UP TO 3 STILL IMAGES CAN BE
● Stop video shooting, then record a still image.
TAKEN DURING RECORDING
● Set the POWER/MODE switch to the still picture mode, then record a still
25
image.
29
-
CANNOT TAKE MORE STILL
IMAGES AT THE MOMENT
● Stop video shooting, and then record a still image.
● When the [SYSTEM SELECT] menu is set to [720-**], still pictures cannot be
captured.
20
-
RECORDING FAILURE
● Turn off and on the power of the camcorder.
● Select [OK] to start recovery.
VIDEO MANAGEMENT FILE IS
DAMAGED, RECOVERY IS
REQUIRED TO RECORD/
PLAYBACK, RECOVER?
24, 63
● The request for recovery screen may appear repeatedly even if [OK] is
selected. When this happens, format the SD card. All data will be deleted.
-
-
UNSUPPORTED SCENE!
● Use files that are recorded using this camcorder. (Playback of files recorded
by other models may fail.)
● Turn off the write protection switch on the SD card.
CHECK CARD'S WRITE CHECK
CARD'S WRITE
51
INSUFFICIENT SPACE
● Delete unwanted files, or move the files to a PC.
● Replace the SD card with a new one.
23
● NUMBER OF FOLDERS
OVERFLOW
● When in the video mode, perform either of the following operations.
– Delete unwanted folders/files, or move them to a PC.
– To delete all recorded videos, select [FORMAT] in the [MEDIA SETTINGS]
menu.
24, 63
● FILE QUANTITY LIMIT
EXCEEDED
● UPPER LIMIT OF RECORDABLE ● When in the still picture mode, move the folders/files to a PC, then select
NUMBER OF FOLDERS/FILES
[FILE + MANAGEMENT NO] in [FORMAT].
HAS BEEN REACHED
24, 63
UPPER LIMIT OF RECORDABLE
MANAGEMENT NUMBERS HAS
BEEN REACHED
● Reset the video file number.
25
-
NO FILES
● No still pictures have been recorded. Set the POWER/MODE switch to the
video mode.
● Resume shooting after a short while. (Shooting stops automatically when it is
(12 HOURS LIMITATION)
RECORDING CANCELLED
performed continuously for more than 12 hours.)
72
Estimated Recordable
Time/Number
The estimated recording time and estimated number of still picture shots are only a guide. Changes may occur depending on the
shooting environment, SD card in use, and the battery condition.
Estimated Video Recording Time
QuickTime/MP4
Quality
SDHC Card
4GB
12 m
17 m
22 m
8GB
25 m
35 m
45 m
16GB
50 m
32GB
1 h 40 m
2 h 20 m
3 h
HQ(1080i/720p)
SP(1080i)
1 h 10 m
1 h 30 m
SP(720P)
Estimated Number of Still Picture Shots
Unit: Number of Shots
SD Card
SDHC Card
8GB 16GB
8420 9999
Image Size Image Quality
512MB
510
1GB
1040
2GB
4GB
4200
6410
5540
8700
9999
9999
32GB
9999
FINE
2100
1920
ן 1080 (16:9)
STANDARD
FINE
800
680
1630
1370
2160
6720
9999
3210
2770
4360
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
1440
ן 1080 (4:3)
STANDARD
FINE
1060
3320
5980
640
ן 480 (4:3)
STANDARD
73
Others
Ⅵ Still Picture
Still picture
recording format
Specifications
:
:
JPEG
Recording size
4 modes
1920 x 1080
1440 x 1080
1024 x 768
640 x 480
Camcorder
Recording quality
:
:
2 modes
Fine, Standard
Ⅵ General
Power
Ⅵ Terminals
AV terminal
:
:
DC 11 V (using AC adapter)
DC 7.2 V (using battery)
Video Analog output 1.0 V (p-p), 75 K
Audio Analog output (stereo)
-8 dBu, 1 kK (when reference level
-12 dB is selected)
-16 dBu, 1 kK (when reference level
-20 dB is selected)
Power consumption
Approx 7.8 W
(when backlight is set to [STANDARD]
while the LCD screen or viewfinder is in
use)
Rated Current Consumption: 1A
Component terminal
:
Y, PB, PR component output
Y: 1.0 V (p-p), 75 K
PB, PR: 700 mV (p-p), 75 K
Dimensions
Mass
:
:
366 mm (W) × 179 mm (H) × 138 mm (D)
(14-4/8" × 7-1/8" × 5-4/8")
Approx. 1190 g (2.7 lbs)
Approx. 1320 g (2.9 lbs) (incl. battery BN-
VF823U, SD card, micorophone)
HDMI terminal
USB terminal
:
:
:
HDMIீ Connector
Mini USB-B type, USB 2.0
Headphone jack
3.5 mm mini-jack
(stereo)
Allowable operating
temperature
:
:
0°C to 40°C (32°F to 104°F)
Microphone terminal
Allowable operating
humidity
:
3.5 mm mini-jack (stereo)
Supports plug-in power
35 % RH to 80 % RH
Allowable storage
temperature
Audio INPUT1/INPUT2 terminals
:
:
:
-20°C to 50°C (-4J to 122J)
MIC
:
-60 dBu, 3 kK, XLR (balanced),
+48 V output (phantom power supply)
Image pickup device
Lens
1/4", Progressive CCD
ן 3 F1.8 to 2.8
f = 3.7 mm to 37 mm
LINE
:
+4 dBu, 10 kK, XLR (balanced)
Filter diameter
:
When the hood is detached
46 mm (screw pitch: 0.75 mm)
Compatible with filter (external diameter:
50 mm and below), tele-converter, and
wide-converter
Accessories
AC adapter
1
Power Cord (For AC adapter and Battery charger)
2
1
1
1
1
1
1
1
1
1
1
1
Battery
When the hood is attached
72 mm (screw pitch: 0.75 mm)
Compatible with filter (external diameter:
75mm and below) only
T When removing the filter, do not press
on the top and bottom of the hood.
Doing so makes it difficult to remove the
filter and may damage the inner surface
of the hood.
Battery charger
Remote control unit
Audio unit
Microphone
AV cord
Component cable
USB cable
Zoom
:
:
:
Up to 10x (optical zoom)
Up to 5x (playback)
CD-ROM
Instruction manual
Warranty card
LCD screen
Viewfinder
2.8", 206,000 pixels, polysilicon liquid
crystal
0.44", 235,000 pixels, polysilicon liquid
crystal
AC Adapter
Power
:
:
AC 110 V to 240 V, 50 Hz/60 Hz
Ⅵ Video/Audio
Video recording
format
Output
DC 11 Vd, 1 A
Allowable operating
temperature
:
:
:
QuickTime File Format (for Final Cut Pro)
MP4 file format
:
:
0°C to 40°C (32°F to 104°F)
Dimensions
47 mm (W) × 28 mm (H) × 72 mm (D)
(1-15/16" × 1-1/8" × 2-7/8")
(excluding cord)
Video format
Video signals
720/24p/25p/30p/50p/60p
1080/24p/25p/30p/50i/60i
720p format
MPEG-2 (8bit, 35/18.3 Mbps)
1080 format
Mass
:
Approx. 86 g (0.19 lbs)
MPEG-2 (8bit, 35/25 Mbps)
Audio signals
:
LPCM 2ch, 48 kHz/16bit
74
Remote Control
Type
:
DC 3 V (button battery CR2025)
Battery life
:
Approx. 1 year (varies according to
frequency of use)
Operating distance
:
Approx. 5 m (16.4ft) (along front axis)
Allowable operating
temperature
:
:
0°C to 40°C (32°F to 104°F)
Dimensions
42 mm (W) × 14.5 mm (H) × 91 mm (D)
(1-6/8" × 9/16" × 3-5/8")
Mass
:
Approx. 30 g (0.07 lbs)
(including button battery)
Dimensional Outline Drawing
(Unit: mm)
T
W
AUTO MANUAL
CH-1
CH-2
CH-2 INPUT AUDIO INPUT
-
LINE
MIC
-
AUDIO
SELECT
INPUT1
INPUT2
-
-
MIC+48V
INPUT1
INPUT2
AUTO MANUAL
USER1 USER2
ND
FILTER
ON
FOCUS
ZOOM
OFF
AF/MF
FULL AUTO
GAIN WHT.BAL
A
/
B
L-
B-
AWB
M-
H-
A-
PRST-
A
B
(without battery)
(hood)
30
184
200
(with battery)
272
366
● The specifications and appearance of this product are subject to changes for further improvement without prior notice.
75
© 2010 Victor Company of Japan, Limited
LYT2089-001D
|