Dear Customer,
Thank you for purchasing this digital
video camera. Before use, please
read the safety information and
precautions contained in the pages
2 – 5 to ensure safe use of this
product.
ENGLISH
DIGITAL VIDEO CAMERA
8
GETTING STARTED
GR-D390U
VIDEO RECORDING &
PLAYBACK
19
DIGITAL STILL CAMERA
(D.S.C.) RECORDING &
Please visit our Homepage on the World Wide Web for
Digital Video Camera:
PLAYBACK
26
31
46
55
For Accessories:
ADVANCED FEATURES
REFERENCES
TERMS
For Customer Use:
Enter below the Model No. and
Serial No. which is located on the
bottom of the camcorder. Retain this
information for future reference.
Model No.
Serial No.
To deactivate the demonstration,
set “DEMO MODE” to “OFF”.
(੬ pg. 31, 34)
INSTRUCTIONS
EN
LYT1528-001B
EN
3
SAFETY PRECAUTIONS
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
(212°F) or incinerate.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
● Dispose of used battery promptly.
● Keep away from children.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
● Do not disassemble and do not dispose of in
fire.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
NOTES:
● The rating plate (serial number plate) and
safety caution are on the bottom and/or the
back of the main unit.
● The rating information and safety caution of the
AC Adapter are on its upper and lower sides.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTIONS:
● This camcorder is designed to be used with
NTSC-type color television signals. It cannot be
used for playback with a television of a different
standard. However, live recording and LCD
monitor/viewfinder playback are possible
anywhere.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF707U/VF714U/VF733U battery packs
and, to recharge them or to supply power to the
camcorder from an AC outlet, use the provided
multi-voltage AC Adapter. (An appropriate
conversion adapter may be necessary to
accommodate different designs of AC outlets in
different countries.)
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material -
special handling may apply.
perchlorate
4
EN
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on
all sides to allow for ventilation (10 cm (3-15/16")
or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Only use attachments/accessories specified by
the manufacturer.
10. Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus. When a
cart is used, use
caution when
moving the cart/
apparatus combination to avoid injury from tip-
over.
Do not point the lens or the viewfinder directly into
the sun. This can cause eye injuries, as well as
lead to the malfunctioning of internal circuitry.
There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
11. Unplug this apparatus during lightning storms or
when unused for long periods of time.
12. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
When carrying, be sure to always securely attach
and use the provided strap. Carrying or holding
the camcorder by the viewfinder and/or the LCD
monitor can result in dropping the unit, or in a
malfunction.
Take care not to get your finger caught in the
cassette holder cover. Do not let children operate
the camcorder, as they are particularly
susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to
the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camcorder to fall, resulting in damage.
EN
5
● Microsoft® and Windows® are either registered
trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
● Macintosh is a registered trademark of Apple
Computer, Inc.
Before Using This Camcorder
Make sure you only use cassettes with the Mini
DV mark
Make sure you only use memory cards with the
mark or
.
.
● QuickTime is a registered trademark of Apple
Computer, Inc.
This camcorder is designed exclusively for the
digital video cassette, SD Memory Card and
MultiMediaCard. Only cassettes marked “
”
and memory cards marked “
” or
“
” can be used with this unit.
Remember that this camcorder is not
compatible with other digital video formats.
Remember that this camcorder is intended for
private consumer use only.
Any commercial use without proper permission is
prohibited. (Even if you record an event such as a
show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
Before recording important video, be sure to
make a trial recording.
Play back your trial recording to make sure the
video and audio have been recorded properly.
We recommend cleaning your video heads
before use.
If you haven’t used your camcorder for a while, the
heads may be dirty. We recommend periodically
cleaning the video heads with a cleaning cassette
(optional).
Be sure to store your cassette tapes and
camcorder in the proper environment.
Video heads can become dirty more easily if your
area. Cassette tapes should be removed from the
camcorder and stored in cassette cases. Store the
camcorder in a bag or other container.
Use SP (Standard) mode for important video
recordings.
LP (Long Play) mode lets you record 50% more
video than SP (Standard) mode, but you may
experience mosaic-like noise during playback
depending on the tape characteristics and the
usage environment.
So, for important recordings, we recommend using
SP mode.
It is recommended that you use JVC brand
cassette tapes.
Your camcorder is compatible with all brands of
commercially available cassette tapes complying
with the MiniDV standard, but JVC brand cassette
tapes are designed and optimized to maximize the
performance of your camcorder.
Also read “CAUTIONS” on pages 51 – 53.
6
EN
Major Features of this Camcorder
Wipe/Fader Effects
You can use the Wipe/Fader Effects to make
pro-style scene transitions. (੬ pg. 40)
Simply pressing the BACKLIGHT button
brightens the image darkened by backlight.
(੬ pg. 39)
● You can also select a spot metering area so
that more precise exposure compensation
is available. (੬ pg. 39, Spot Exposure
Control)
Fade in
Fade out
You can check the battery status by simply
pressing the DATA button. (੬ pg. 14)
Program AE, Effects and Shutter Effects
For example, “SPORTS” mode allows fast-
moving images to be captured one frame at a
time, for vivid, stable slow-motion. (੬ pg. 41)
BATTERY CONDITION
MAX TIME
100%
LCD
min
min
50%
0%
FINDER
Live Slow
You can record and play back precious or
hard-to-see moments at a slow speed. The
sound is recorded and played back in real
time. (੬ pg. 36)
LED Light
You can brighten the subject in the dark place
with the LED Light. (੬ pg. 36)
Auto Button
You can change the recording mode between
manual setting to the standard mode setting
of the camcorder by pressing the AUTO
button.
AUTO
MANUAL
GETTING STARTED
Language Settings.......................................... 16
Tripod Mounting.............................................. 17
Snapshot (Record Still Image On Tape)......... 37
White Balance Adjustment.............................. 39
Manual White Balance Adjustment................. 40
Program AE, Effects And Shutter Effects ....... 41
VIDEO RECORDING ........................................... 19
Basic Recording ............................................. 19
Tape Remaining Time ................................ 19
LCD Monitor And Viewfinder ...................... 19
Journalistic Shooting .................................. 20
VIDEO PLAYBACK ............................................. 21
Normal Playback ............................................ 21
Still Playback .............................................. 21
Blank Search .............................................. 22
Connections To A TV Or VCR........................ 23
Playback Using The Remote Control ............. 24
46
TROUBLESHOOTING .......................................... 46
USER MAINTENANCE......................................... 50
CAUTIONS ........................................................ 51
SPECIFICATIONS................................................ 54
DIGITAL STILL CAMERA (D.S.C.) RECORDING
& PLAYBACK
26
TERMS
55
D.S.C. RECORDING............................................ 26
Basic Shooting (D.S.C. Snapshot) ................. 26
D.S.C. PLAYBACK .............................................. 27
Normal Playback Of Images........................... 27
Auto Playback Of Images............................... 27
Index Playback Of Files.................................. 27
Removing On-Screen Display ........................ 27
ADDITIONAL FEATURES FOR D.S.C. .................... 28
Resetting The File Name................................ 28
Protecting Files............................................... 28
Deleting Files.................................................. 29
Setting Print Information (DPOF Setting) ....... 29
Initializing A Memory Card.............................. 30
GETTING STARTED
EN
Controls
Indicators
1Rewind Button [1] (੬ pg. 21)
Left Button [1]
Quick Review Button [QUICK REVIEW]
(੬ pg. 21)
2Set Button [SET] (੬ pg. 16)
Data Battery Button [DATA] (੬ pg. 14)
3Stop Button [7] (੬ pg. 21)
Down Button [4]
Backlight Compensation
Button [BACKLIGHT]
5Play/Pause Button [6] (੬ pg. 21)
Up Button [3]
Card Cover [
Battery Pack Mount (੬ pg. 13)
Speaker (੬ pg. 21)
Lens
LED Light
Camera Sensor
Manual Focus Button [FOCUS] (੬ pg. 37)
6Wide (16:9) Button [16.9] (੬ pg. 36)
Blank Search [BLANK] (੬ pg. 22)
7Menu Button [MENU] (੬ pg. 31)
Right Button [2]
Night Button [NIGHT] (੬ pg. 37)
9Index Button [INDEX] (੬ pg. 27)
LED Light Button [LIGHT]
Stud Hole (੬ pg. 17)
Tripod Mounting Socket (੬ pg. 17)
Cassette Holder Cover (੬ pg. 18)
Memory Card Slot
"Auto Button [AUTO] (੬ pg. 15)
#Snapshot Button [SNAPSHOT]
(੬ pg. 26, 37)
Live Slow Button (੬ pg. 33, 36)
$Power Zoom Lever [T/W] (੬ pg. 20)
Speaker Volume Control [VOL. +, –]
(੬ pg. 21)
(੬ pg. 13)
&Recording Start/Stop Button (੬ pg. 19)
(Power Switch [REC, PLAY, OFF] (੬ pg. 15)
)Lock Button (੬ pg. 15)
~Cassette Open/Eject Switch [OPEN/EJECT]
(੬ pg. 18)
Connectors
The connectors are located beneath the covers.
+USB (Universal Serial Bus) Connector
(੬ pg. 44)
,DigitalVideo Connector [DV IN/OUT] (i.LINK*)
(੬ pg. 43, 44)
*
i.LINK refers to the IEEE1394-1995 industry
specification and extensions thereof. The
logo is used for products compliant with the
i.LINK standard.
-Audio/Video Output Connector [AV]
(੬ pg. 23, 42)
.DC Input Connector [DC] (੬ pg. 13)
GETTING STARTED
EN
10
LCD Monitor/Viewfinder Indications
During Video Recording Only
" #
9
!
1
2
3
4
6
7
8
2 3 4
5
1
M
LP
– – –min
16:9
PHOTO
3
$
%
7
PAUSE
&
W
H
"
!
DEC. 6.2006
SOUND 12BIT
11:13 AM
DEC. 6.2006
(
15:55
1Battery Remaining Power Indicator
2Operation Mode (੬ pg. 15)
: Auto Mode
: Manual Mode
3LED Light Indicator (੬ pg. 36)
9
8
1Tape Running Indicator (੬ pg. 19)
(Rotates while tape is running.)
2Selected Wide Mode Indicator (੬ pg. 36)
3
: Live Slow Indicator (੬ pg. 36)
4
4Recording Speed Mode (SP/LP) (੬ pg. 32)
(only LP indicator is displayed)
5Tape Remaining Time (੬ pg. 19)
6REC: (Appears during recording.) (੬ pg. 19)
PAUSE: (Appears during Record-Standby
mode.) (੬ pg. 19)
: Gain Up Mode (੬ pg. 33)
5Shutter Speed
6White Balance Indicator (੬ pg. 39)
7Selected Effect Indicator
8Selected Program AE Indicator (੬ pg. 41)
9Approximate Zoom Ratio (੬ pg. 20)
!Zoom Indicator (੬ pg. 20)
SLOW: (Appears when using Live Slow.)
(੬ pg. 36)
7Selected Wipe/Fader Effect Indicator
(੬ pg. 40)
8Date/Time (੬ pg. 34)
(Appears and blinks during shooting.)
: Blinks in white when a memory card is
not loaded.
9Time Code (੬ pg. 34)
!Digital Image Stabilizer (“DIS”) (੬ pg. 32)
"SOUND 12BIT/16BIT: Sound Mode Indicator
(੬ pg. 32) (Appears for approx. 5 seconds
after turning on the camcorder.)
: Blinks in yellow while the camcorder is
reading the data in the memory card.
PHOTO: (Appears when taking Snapshot.)
(੬ pg. 26, 37)
: Spot Exposure Control Indicator
(੬ pg. 39)
$
%
During D.S.C. Recording Only
: Backlight Compensation Indicator
(੬ pg. 39)
2
3
: Exposure Adjustment Indicator (੬ pg. 38)
Iris Lock Indicator (੬ pg. 38)
640
15
&Wind Cut Indicator (੬ pg. 33)
(Date (੬ pg. 16)
)Manual Focus Adjustment Indicator
(੬ pg. 37)
1Image Size: 640 (640 x 480) (੬ pg. 26)
2Picture Quality: (FINE) and
(STANDARD) (in order of quality) (੬ pg. 34)
3Remaining Number Of Shots (੬ pg. 26)
(Displays the approximate remaining number
of shots that can be stored during D.S.C.
recording.)
GETTING STARTED
EN
11
During Video Playback
During D.S.C. Playback
1
2
3
4
5
1
LP
100-0013
12B I T / M I X
L
BRIGHT
– 5
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
3
2
VOLUME
3Brightness Control Indicator (LCD monitor/
11
.
:
6
13 AM
20 : 21 : 25
DE C
.
200
6
8
6
7
1Battery Remaining Power Indicator
2Sound Mode Indicator (੬ pg. 35)
3Blank Search Indicator (੬ pg. 22)
4Tape Speed (SP/LP) (੬ pg. 35)
(only LP indicator is displayed)
53: Playback
¡: Fast-Forward/Shuttle Search
1: Rewind/Shuttle Search
8: Pause
83: Forward Frame-By-Frame Playback/
Slow-Motion
28: Reverse Frame-By-Frame Playback/
Slow-Motion
: Audio Dubbing
: Audio Dubbing Pause
8
6Date/Time (੬ pg. 35)
7VOLUME: Volume Level Indicator (੬ pg. 21)
BRIGHT: Brightness Control Indicator (LCD
monitor/Viewfinder) (੬ pg. 17)
8Time Code (੬ pg. 35)
GETTING STARTED
EN
12
How To Attach The Lens Cap
Provided Accessories
To protect the lens, attach
the provided lens cap to the
camcorder as shown in the
illustration.
OR
NOTE:
To confirm the lens cap is on
correctly make sure the cap is
flush to the camcorder.
Place here during
shooting.
How To Attach The Shoulder Strap
Follow the illustration.
1 Thread the strap through the eyelet.
2 Fold it back and thread it through the strap
1 AC Adapter AP-V14U or AP-V18U
2 Battery Pack BN-VF707U
3 Audio/Video Cable (ø3.5 mini-plug to RCA
plug)
4 USB Cable
5 Core Filter (for USB cable, pg. 13 for
attachment)
guide and the buckle.
● To adjust the length of the strap, loosen and then
tighten the strap in the buckle.
3 Slide the strap guide fully towards the eyelet.
Buckle
Strap guide
6 CD-ROM
2
7 Remote Control Unit RM-V720U
8 Lithium Battery CR2025* (for remote control
unit)
9 Memory Card (Already inserted in the
camcorder)
! Shoulder Strap (see the right column for
attachment)
" Lens Cap (see the right column for
attachment)
* A lithium battery is pre-installed in the Remote
Control Unit at time of shipment (with insulation
sheet). To use the Remote Control Unit, remove
the insulation sheet.
3
1
Eyelet
NOTES:
● In order to maintain optimum performance of the
camcorder, provided cables may be equipped with
one or more core filter. If a cable has only one core
filter, the end that is closest to the filter should be
connected to the camcorder.
● Make sure to use the provided cables for
connections. Do not use any other cables.
GETTING STARTED
EN
13
How To Attach The Core Filter
Attach the core filters to the cables. The core
filter reduces interference.
Power
This camcorder’s 2-way power supply system
lets you choose the most appropriate source of
power. Do not use provided power supply units
with other equipment.
1 Release the stoppers on both ends of the
core filter.
Charging The Battery Pack
Battery pack mount
Stopper
2 Run the cable through the core filter, leaving
approx. 3 cm (1-3/16") of cable between the
cable plug and the core filter.
Wind the cable once around the outside of the
core filter as shown in the illustration.
PUSH
BATT.
Battery
pack
1
2
Arrow
POWER/
CHARGE
lamp
Core filter
3 cm (1-3/16")
To DC connector
Wind once
Power switch
3 Close the core filter until it clicks shut.
NOTES:
AC Adapter
● Take care not to damage the cable.
● When connecting a cable, attach the end with the
core filter to the camcorder.
To AC outlet
1 Set the Power Switch to “OFF”.
2 With the arrow on the battery pack pointing
downward, push the battery pack slightly against
the battery pack mount 1.
3 Slide down the battery pack until it locks in
place 2.
4 Connect the AC Adapter to the camcorder.
5 Plug the AC Adapter into an AC outlet. The
POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.
6 When the POWER/CHARGE lamp goes out,
charging is finished. Unplug the AC Adapter
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
CONTINUED ON NEXT PAGE
GETTING STARTED
EN
14
To detach the battery pack
Using The Battery Pack
Perform steps 2 – 3 in “Charging The Battery
Pack”.
Slide the battery pack upward while pressing
PUSH BATT. to detach it.
Battery pack
BN-VF707U*
Charging time
Approx. 1 hr. 30 min.
Approx. 2 hrs. 40 min.
Approx. 5 hrs. 40 min.
Maximum continuous recording time
LCD monitor
Battery pack
Viewfinder on
BN-VF714U
BN-VF733U
* Provided
on
1 hr. 30 min.
3 hrs.
BN-VF707U*
BN-VF714U
BN-VF733U
* Provided
NOTES:
1 hr. 40 min.
3 hrs.25 min.
8 hrs.
NOTES:
7 hrs.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC BN-
VF707U/VF714U/VF733U battery packs. Using
generic non-JVC batteries can cause damage
to the internal charging circuitry.
● Recording time is reduced significantly under the
following conditions:
• Zoom or Record-Standby mode is engaged
repeatedly.
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camcorder cannot be
operated.
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the POWER/
CHARGE lamp may not light. In this case, remove
the battery pack from the camcorder, then try
charging again.
● If a fully charged battery pack is attached to the
unit, the POWER/CHARGE lamp does not blink to
indicate that charging is not performed.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
● Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure to
use it only in well-ventilated areas.
● Using the optional AA-VF7 Battery Charger, you
can charge the BN-VF707U/VF714U/VF733U
battery pack without the camcorder.
● After 5 minutes has elapsed in Record-Standby
mode with the cassette inserted and no operation
is performed (“PAUSE” indicator may not appear),
the camcorder will automatically turn off its power
supplied from the AC adapter. In this case, the
battery charge starts if the battery is attached to
the camcorder.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
• The LED Light is used.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
ATTENTION:
Before detaching the power source, make sure that
the camcorder’s power is turned off. Failure to do so
can result in a camcorder malfunction.
Data Battery System
You can check the remaining battery power and
the recordable time.
1) Make sure the battery is attached and the
Power Switch is set to “OFF”.
2) Open the LCD monitor fully.
3) Press DATA, and the battery status screen
appears.
● It is displayed for approx. 3 seconds if the
button is pressed and released quickly, and for
approx. 15 seconds if the button is pressed
and hold for several seconds.
● If “COMMUNICATION ERROR” appears
instead of the battery status even though you
tried to press DATA several times, there may
be a problem with your battery. In such a case,
consult your nearest JVC dealer.
GETTING STARTED
EN
15
Using AC Power
Perform step 4 in “Charging The Battery Pack”.
Power Switch Position
REC:
● Allows you to set various recording functions
using the menus. (੬ pg. 32)
NOTE:
The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
OFF:
Allows you to switch off the camcorder.
About Batteries
PLAY:
DANGER! Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its
terminals to come in contact with metals, as this
can result in a short circuit and possibly start a
fire.
● Allows you to play back a recording on the
tape.
● Allows you to display a still image stored in
the memory card or to transfer a still image
stored in the memory card to a PC.
● Allows you to set various playback functions
using the Menus. (੬ pg. 31)
To resume the original function of the
accurate battery power indication
VIDEO/MEMORY Switch Position
If the battery power indication differs from the
actual operating time, fully charge the battery, and
then run it down. However this function may not
turn back if the battery was used for a long period
of time under extremely high/low temperature
condition or charged too many times.
VIDEO:
Allows you to record on a tape or play back a
tape. If “REC SELECT” is set to “
/
”
(੬ pg. 34), still images are recorded both on
the tape and the memory card.
MEMORY:
● Allows you to record in a memory card or
access data stored in a memory card.
● When the Power Switch is set to “REC”, the
Operation Mode
To turn on the camcorder, set the Power Switch
to any operation mode except “OFF” while
pressing down the Lock Button located on the
switch.
currently selected image size appears.
Auto/Manual Mode
Press AUTO button repeatedly to switch to auto/
CHARGE lamp manual recording mode. When manual mode is
selected, the indicator “ ” appears on the LCD
monitor.
Lock Button
POWER/
AUTO
VIDEO/
MEMORY
MENU
Auto Mode :
You can record using no special effects or
manual adjustments.
Power Switch
Manual Mode :
Manual recording is possible by setting various
functions.
Choose the appropriate operation mode
according to your preference using the Power
Switch and VIDEO/MEMORY Switch.
AUTO
MANUAL
GETTING STARTED
EN
16
Power-Linked Operation
Date/Time Settings
times, but its display can be turned on or off
during playback. (੬ pg. 34, 35)
When the Power Switch is set to “REC”, you can
also turn on/off the camcorder by opening/
closing the LCD monitor or pulling out/pushing in
the viewfinder.
1 Perform steps 1 – 5 in “Language Settings”
INFORMATION:
on the left column.
The following explanations in this manual
supposes the use of LCD monitor in your
operation. If you want to use the viewfinder,
close the LCD monitor and pull out the
viewfinder fully.
2 Press 3, 4, 2or 1to select “CLOCK ADJ.”,
and press SET. The date display format is
highlighted.
3 Press 3or 4to select the desired date
display format, then press SET or 2. Select from
“MONTH.DATE.YEAR”, “DATE.MONTH.YEAR”
or “YEAR.MONTH.DATE”.
Language Settings
The language on the display can be changed.
4 Press 3or 4to select the time display
format, then press SET or 2. Select from “24h”
or “12h”.
(੬ pg. 31, 34)
1 Set the Power Switch to “REC” while pressing
down the Lock Button located on the switch.
5 Set the year, month, date, hour and minute.
Press 3or 4to select the value, then press SET
or 2. Repeat this step until you have input all the
settings.
2 Open the LCD monitor fully. (੬ pg. 19)
3 Set the recording mode to “ ”.(੬ pg. 15)
4 Press MENU. The Menu Screen appears.
5 Press 3, 4, 2or 1to
NOTE:
Press 1to return to the previous setting.
LANGUAGE
select “DISPLAY”, and
6 Press MENU.The Menu
press SET. The DISPLAY
Menu appears.
CLOCK ADJ
.
screen closes.
DEMO
MO
NTH . DATE . YEAR
12h
0001
6 Press 3, 4, 2or 1to
select “LANGUAGE”, and
DEC . 06 . 2 006
07 : 05 AM
press SET.
7 Press 3or 4to select
LANGUAGE
the desired language, and
press SET or 2.
● Press 1whenever you
want to return to the
previous menu screen.
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS
8 Press MENU. The
Menu Screen closes.
GETTING STARTED
EN
17
Grip Adjustment
Brightness Adjustment Of The
Display
1 Set the Power Switch
to “REC” or “PLAY” while
pressing down the Lock
1 Adjust the velcro strip.
● Before making the
adjustment, remove any
security tags that may
be attached to the
velcro.
3
2
Button located on the
switch.
1
2 Pass your right hand
through the loop and
grasp the grip.
2 Open the LCD monitor
4
fully. (੬ pg. 19)
● To adjust the brightness of
the viewfinder, pull out the
viewfinder fully and set
“PRIORITY” to “FINDER”
(੬ pg. 31, 33).
3 Adjust your thumb and
fingers through the grip to
MENU
easily operate the Recording Start/Stop Button,
Power Switch and Power Zoom Lever. Be sure
to fasten the velcro strip to your preference.
BRIGHT
– 5
3 Press MENU. The
Menu Screen appears. If
you are in Playback mode,
please proceed to Step 5.
Viewfinder Adjustment
1 Set the Power Switch to “REC” while pressing
4 Press 3, 4, 2or 1to select “DISPLAY”, and
down the Lock Button located on the switch.
press SET. The DISPLAY Menu appears.
2 Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully and adjust it
manually for best viewability.
5 Press 3, 4, 2or 1to select “BRIGHT”, and
press SET. The Menu Screen closes and the
brightness control menu appears.
3 Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.
Example:
6 Press 3or 4until the appropriate brightness
is reached and press SET or 2.
7 Press MENU. The menu screen closes.
Tripod Mounting
To attach the camcorder
to a tripod, align the
direction stud and screw
to the mounting socket
and stud hole on the
camcorder. Then tighten
the screw clockwise.
● Some tripods are not
equipped with studs.
Diopter Adjustment Control
CAUTION:
When retracting the viewfinder, take care not to
pinch your fingers.
GETTING STARTED
EN
18
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
● When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
Loading/Unloading A Cassette
The camcorder needs to be powered up to load
or eject a cassette.
OPEN/EJECT
Cassette holder
cover
PUSH
Loading/Unloading A Memory
Card
The provided memory card is already inserted in
the camcoder at the time of purchase.
Card Cover (
)
Erase
protection tab
Cassette holder
Make sure the window side
is facing out.
Memory card
1 Slide and hold OPEN/EJECT in the direction
of the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically.
Write/erase protection tab
Clipped edge
1 Make sure the camcorder’s power is off.
).
● Do not touch internal components.
2 Open the card cover (
2 Insert or remove a tape and press “PUSH” to
3 To load a memory card, firmly insert it with
close the cassette holder.
its clipped edge first.
● Be sure to press only the section labeled “PUSH”
to close the cassette holder; touching other parts
may cause your finger to get caught in the
cassette holder, resulting in injury or product
damage.
To unload a memory card, push it once. After
the memory card comes out of the camcorder,
pull it out.
● Do not touch the terminal on the reverse side of
the label.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you may
not be able to close the cassette holder cover. Do
not apply force. Replace the battery pack with a
fully charged one or use AC power before
continuing.
4 Close the card cover.
To protect valuable files (available only for
SD Memory Card)
Slide the write/erase protection tab on the side
of the memory card in the direction of “LOCK”.
This prevents the memory card from being
recorded over. To record on this memory card,
slide the tab back to the position opposite to
“LOCK” before loading it.
3 Close the cassette holder cover firmly until it
locks into place.
To protect valuable recordings
NOTES:
Slide the erase protection tab on the back of the
tape in the direction of “SAVE”.This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading
it.
● Some brands of memory cards are not compatible
with this camcorder. Before purchasing a memory
card, consult its manufacturer or dealer.
● Before using a new memory card, it is necessary
to format the card. (੬ pg. 30)
NOTES:
ATTENTION:
● If you wait a few seconds and the cassette holder
does not open, close the cassette holder cover
and try again. If the cassette holder still does not
open, turn the camcorder off then on again.
Do not insert or remove the memory card while the
camcorder is turned on, as this may cause the
memory card to be corrupted or cause the
camcorder to become unable to recognize whether
or not the card is installed.
VIDEO RECORDING
EN
19
● When a blank portion is left between recorded
Basic Recording
scenes on the tape, the time code is interrupted
and errors may occur when editing the tape. To
avoid this, refer to “Recording From The Middle Of
A Tape” (੬ pg. 21).
NOTE:
Before continuing, perform the procedures listed
below:
● To turn the melody sounds off, ੬ pg. 33.
● Power (੬ pg. 13)
● Loading A Cassette (੬ pg. 18)
Tape Remaining Time
Approximate tape remaining
time appears on the display.
“– – – min” means the
camcorder is calculating the
remaining time. When the
VIDEO/MEMORY
Zoom Lever
remaining time reaches 2 minutes, the indication
starts blinking.
POWER/CHARGE Lamp
● The time required to calculate and display the
remaining tape length, and the accuracy of the
calculation, may vary according to the type of tape
used.
Lock Button
Recording Start/Stop Button
LCD Monitor And Viewfinder
While using the LCD monitor:
1 Remove the lens cap. (੬ pg. 12)
2 Open the LCD monitor fully.
Make sure the viewfinder is pushed back in. Pull
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
on the end
of the LCD monitor and open the
4 Set the Power Switch to “REC” while pressing
down the Lock Button located on the switch.
● The POWER/CHARGE lamp lights and the
camcorder enters the Record-Standby mode.
LCD monitor fully. It can rotate 270° (90°
downward, 180° upward).
“
PAUSE” is displayed.
● To record in LP (Long Play) mode, ੬ pg. 32.
5 To start recording, press the Recording Start/
Stop Button. “
REC” appears on the display
while recording is in progress.
6 To stop recording, press the Recording Start/
Stop Button again. The camcorder re-enters the
Record-Standby mode.
While using the viewfinder:
Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully.
Approximate recording time
NOTES:
Recording mode
Tape
● The image will not appear simultaneously on the
LCD monitor and the viewfinder. When the
viewfinder is pulled out while the LCD monitor is
opened, you can select which one to use. Set
“PRIORITY” to the desired mode in SYSTEM
Menu. (੬ pg. 33)
SP
LP
45 min.
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
90 min.
120 min.
● Colored bright spots may appear all over the LCD
monitor or the viewfinder. However, this is not a
malfunction. (੬ pg. 47)
NOTES:
● If the Record-Standby mode continues for
5 minutes and no operation is performed
(“
PAUSE” indicator may not appear), the
camcorder’s power shuts off automatically.To turn
the camcorder on again, push back and pull out
the viewfinder again or close and re-open the LCD
monitor.
VIDEO RECORDING
EN
20
Zooming
Journalistic Shooting
Produces the zoom in/out effect, or an
instantaneous change in image magnification.
In some situations,
different shooting
angles may provide
more dramatic results.
Hold the camcorder in
the desired position
and tilt the LCD
monitor in the most
convenient direction. It
can rotate 270° (90°
downward, 180°
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Slide the Power Zoom Lever towards “W”.
● The further you slide the Power Zoom Lever, the
quicker the zoom action.
Zoom in (T:Telephoto)
upward).
1
x
10
x
20
x
40
x
During recording, a time code is recorded on the
tape. This code is to confirm the location of the
recorded scene on the tape during playback.
Display
Zoom out (W:Wide angle)
10
x
Minutes
Digital zoom zone
32X (optical) zoom zone
Seconds
Frames*
(30 frames = 1 second)
12 : 34 : 24
Approximate zoom ratio
NOTES:
* Frames are not displayed during recording.
● Focusing may become unstable during Zooming.
In this case, set the zoom while in Record-
Standby, lock the focus by using the manual focus
(੬ pg. 37), then zoom in or out in Record mode.
● Zooming is possible to a maximum of 800X, or it
can be switched to 32X magnification using the
optical zoom. (੬ pg. 33)
● Zoom magnification of over 32X is done through
Digital image processing, and is therefore called
Digital Zoom.
If recording starts from a blank portion, the time
code begins counting from “00:00:00”
the end of a previously recorded scene, the time
code continues from the last time code number.
If during recording a blank portion is left partway
through the tape, the time code is interrupted.
When recording is resumed, the time code
starts counting up again from “00:00:00”. This
means the camcorder may record the same time
codes as those existing in a previously recorded
scene. To prevent this, perform Recording From
The Middle Of A Tape (੬ pg. 21) in the following
cases;
● When shooting again after playing back a
recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during
shooting.
● When shooting using a partially recorded tape.
● When shooting on a blank portion located partway
through the tape.
● When shooting again after shooting a scene then
opening/closing the cassette holder cover.
● During Digital zoom, the quality of image may
suffer.
● Digital zoom cannot be used when the VIDEO/
MEMORY Switch is set to “MEMORY”.
●
Macro shooting (as close as approx. 5 cm (2") to
the subject) is possible when the Power Zoom
Lever is set all the way to “W”. Also see “TELE
MACRO” in FUNCTION Menu on page 32.
● When shooting a subject close to the lens, zoom
out first. If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out
depending on the distance between the
camcorder and the subject. This will not occur
when “TELE MACRO” is set to “ON”. (੬ pg. 32)
VIDEO PLAYBACK
EN
21
NOTES:
Normal Playback
¡¡
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
CODE” is set to “ON”. (੬ pg. 34)
VOL. +/–
Lock Button
66
11
Speaker
Quick Review
Enables to check the end of the last recording.
1) Press QUICK REVIEW during the Recording-
Standby mode.
2) Tape is rewound for about several seconds
and played back automatically, then pauses in
the Recording-Standby mode for the next shot.
● Distortion may occur at start of playback. This is
normal.
VIDEO/
MEMORY
MENU
7
1 Load a cassette. (੬ pg. 18)
2 Set the VIDEO/MEMORY Switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
Recording From The Middle Of A Tape
1) Play back a tape or use Blank Search
(੬ pg. 22) to find the spot at which you want to
start recording, then engage the Still Playback
mode. (See the right column.)
2) Set the Power Switch to “REC” while pressing
down the Lock Button located on the switch,
then start recording.
4 To start playback, press 6.
5 To stop playback, press 7.
● During Stop mode, press 1to rewind, or ¡to
fast-forward the tape.
To control the speaker volume
Slide the Power Zoom Lever (VOL. +/–) towards
“+” to turn up the volume, or towards “–” to turn
down the volume.
NOTES:
● The playback picture can be viewed in the LCD
monitor, viewfinder or on a connected TV.
(੬ pg. 23)
● If Stop mode continues for 5 minutes when power
is supplied from a battery, the camcorder shuts off
automatically. To turn on again, set the Power
Switch to “OFF”, then to “PLAY”.
● When a cable is connected to the AV connector,
the sound is not heard from the speaker.
Still Playback
Pauses during video playback.
1) Press 6during playback.
2) To resume normal playback, press 6again.
● If still playback continues for more than about
3 minutes, the camcorder’s Stop mode is
automatically engaged.
VIDEO PLAYBACK
EN
22
Shuttle Search
Allows high-speed search in either direction
during video playback.
1) During playback, press ¡for forward
search, or 1for reverse search.
2) To resume normal playback, press 6.
● During playback, press and hold ¡or 1. The
search continues as long as you hold the button.
Once you release the button, normal playback
resumes.
NOTES:
● Before starting Blank Search, if the current
position is at a blank portion, the camcorder
searches in the reverse direction. If the current
position is at a recorded portion, the camcorder
searches in the forward direction.
during Blank Search, the camcorder stops
● A blank portion which is shorter than 5 seconds of
tape may not be detected.
● The detected blank portion may be located
between recorded scenes. Before you start
recording, make sure there is no recorded scene
after the blank portion.
● A slight mosaic effect appears on the display
during Shuttle Search. This is not a malfunction.
ATTENTION:
During Shuttle Search, parts
of the picture may not be
clearly visible, particularly on
the left side of the screen.
Blank Search
Helps you find where you should start recording
in the middle of a tape to avoid time code
interruption. (੬ pg. 20)
1 Load a cassette. (੬ pg. 18)
2 Set the VIDEO/MEMORY Switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
4 Press BLANK.
● The “BLANK SEARCH” indication appears and
the camcorder automatically starts reverse or
forward search, then stops at the spot which is
about 3 seconds of tape before the beginning of
the detected blank portion.
● To cancel Blank Search, press 7or BLANK.
VIDEO PLAYBACK
1 Make sure all units are turned off.
Connections To A TV Or VCR
2 Connect the camcorder to a TV or VCR as
shown in the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
referring to your VCR’s instruction manual.
To AV
connector
4 Turn on the camcorder, the VCR and the TV.
5 Set the VCR to its AUX input mode, and set
the TV to its VIDEO mode.
6 Start playback on the camcorder. (੬ pg. 21)
To choose whether or not the following
displays appear on the connected TV
● Date/Time
Audio/Video cable
(provided)
Set “DATE/TIME” to “ON” or “OFF”.
(੬ pg. 31, 35)
Or, press DISPLAY on the remote control to turn
on/off the date indication.
● Time Code
Set “TIME CODE” to “ON” or “OFF”.
(੬ pg. 31, 35)
TV
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
(੬ pg. 31, 35)
VCR
NOTES:
1Yellow to VIDEO IN (Connect when your TV/
VCR has only A/V input connectors.)
2Red to AUDIO R IN*
3White to AUDIO L IN*
* Not required for watching still images only.
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 15)
● To monitor the picture and sound from the
camcorder without inserting a tape or memory
card, set the camcorder’s Power Switch to “REC”,
then set your TV to the appropriate input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
VIDEO PLAYBACK
EN
24
The following buttons are available only when
the camcorder’s Power Switch is set to “PLAY”.
2PAUSE Button
● Pauses the tape (੬ pg. 25)
Up Button (੬ pg. 25)
3SLOW Rewind Button (੬ pg. 25)
4REW Button
● Rewind/Reverse Shuttle Search on a tape
(੬ pg. 22)
Playback Using The Remote
Control
The Full-Function Remote Control Unit can
operate this camcorder from a distance as well
as the basic operations (Playback, Stop, Pause,
Fast-Forward and Rewind) of your VCR. It also
makes additional playback functions possible.
(੬ pg. 25)
● Displays previous file in a memory card
(੬ pg. 27)
Left Button (੬ pg. 25)
Installing The Battery
The remote control uses
one lithium battery
(CR2025).
5INSERT Button (੬ pg. 45)
6SHIFT Button (੬ pg. 25)
7DISPLAY Button (੬ pg. 23, 42)
8SLOW Forward Button (੬ pg. 25)
9PLAY Button
● Starts Playback of a tape (੬ pg. 21)
● Starts Auto Playback of images in a memory
card (੬ pg. 27)
!FF Button
● Forward/Forward Shuttle Search on a tape
(੬ pg. 22)
● Displays next file in a memory card (੬ pg. 27)
Right Button (੬ pg. 25)
2
1
1 Pull out the battery
3
holder by pushing the lock
tab.
1
Lock tab
2 Insert the battery in the
holder, and be sure to
have the “+” mark visible.
3 Slide the holder back in until you hear a click.
Beam Effective Area (indoor use)
"A. DUB Button (੬ pg. 45)
#STOP Button
● Stops the tape (੬ pg. 21)
● Stops Auto Playback (੬ pg. 27)
Down Button (੬ pg. 25)
$EFFECT Button (੬ pg. 25)
%EFFECT ON/OFF Button (੬ pg. 25)
The following buttons are available when the
camcorder’s Power Switch is set to “REC”.
&Zoom (T/W) Buttons
Zoom in/out (੬ pg. 20, 25)
(Also available with the Power Switch set to
“PLAY”)
When using the remote
control, be sure to point it
at the remote sensor.The
transmitted beam’s
approximate effective
distance for indoor use is
5 m (16 ft).
Remote sensor
NOTE:
The transmitted beam may not be effective or may
cause incorrect operation when the remote sensor
is directly exposed to sunlight or powerful lighting.
(START/STOP Button
Functions the same as the Recording Start/
Stop Button on the camcorder.
)S.SHOT Button
Buttons And Functions
Functions the same as SNAPSHOT on the
camcorder.
(Also available with the Power Switch set to
“PLAY”)
1Infrared beam transmitting window
● Transmits the beam signal.
VIDEO PLAYBACK
EN
25
.
2) At the point you want to zoom
in, press the Zoom Button (T).
● To zoom out, press the Zoom
Button (W).
PAUSE or
(Up)
Zoom (T/W)
SLOW (
SLOW (
)
)
3) You can move the image on
the screen around to find a
particular portion of the picture.
While holding down SHIFT,
PLAY
(Right)
STOP or
(Left)
(Down)
press
(Up) and
(Left), (Right),
(Down).
SHIFT
● To end zoom, press and hold W until
Slow-Motion Playback
magnification returns to normal. Or, press STOP
(7) and then press PLAY (3) during video
playback.
● To end zoom during D.S.C. playback, press PLAY
(3).
During normal video playback, press SLOW (
or ) more than approx. 2 seconds.
● After approx. 10 minutes, normal playback
resumes.
● To pause Slow-Motion playback, press PAUSE
(PAUSE).
NOTES:
● Zoom can also be used during slow-motion and still
playback.
● To stop Slow-Motion playback, press PLAY (3).
● Due to digital image processing, the quality of the
image may suffer.
NOTES:
● You can also engage Slow-Motion Playback from
Still Playback by pressing SLOW (
than approx. 2 seconds.
● During Slow-Motion Playback, due to digital
image processing, the picture may take on a
mosaic effect.
or
) more
Playback Special Effects
Allows you to add creative effects to the video
playback image.
SEPIA: Recorded scenes have a brownish
tint like old photos. Combine this with the
Cinema mode (੬ pg. 36, “WIDE MODE”) for a
classic look.
MONOTONE: Like classic black and white
films, your footage is shot in B/W. Used together
with the Cinema mode (੬ pg. 36, “WIDE
● After SLOW (
or
) is pressed and held, the
still image may be displayed for a few seconds,
followed by a blue screen for a few seconds. This
is not a malfunction.
● During Slow-Motion Playback, there will be
disturbances in video and the picture may seem
unstable, especially with steady images. This is
not a malfunction.
MODE”), it enhances the “classic film” effect.
CLASSIC: Gives recorded scenes a
strobe effect.
Frame-By-Frame Playback
STROBE:Your recording looks like a
series of consecutive snapshots.
1) To start
During normal or still playback, press SLOW
(
) repeatedly for forward or SLOW (
)
repeatedly for reverse. Each time SLOW ( or
EFFECT ON/OFF
playback,
) is pressed, the frame is played back.
EFFECT
press PLAY
(3).
2) Press
EFFECT. The
PLAYBACK EFFECT Select Menu appears.
3) Press EFFECT repeatedly to move the
highlight bar to the desired effect.
● The selected function is activated and after
2 seconds the menu disappears.
Playback Zoom
Magnifies the recorded image up to 25X at any
time during video playback and D.S.C. playback.
1) Press PLAY (3) to start video
playback. Or perform normal
playback of images.
● To deactivate the selected effect, press EFFECT
ON/OFF. To reactivate the selected effect press
EFFECT ON/OFF again.
● To change the selected effect, repeat from step 2
above.
D.S.C. RECORDING
EN
26
Approximate Number of Storable Images
● The number increases or decreases depending
Basic Shooting (D.S.C. Snapshot)
You can use your camcorder as a Digital Still
Camera for taking snapshots. Still images are
stored in the memory card.
SD Memory Card
Image Size/Picture
Quality
8 MB 16 MB 32 MB 64 MB
640 x 480/FINE
47
95 205 425
NOTE:
Before continuing, perform the procedures listed
below:
● Power (੬ pg. 13)
● Loading a Memory Card (੬ pg. 18)
MultiMediaCard
Image Size/Picture
Quality
SNAPSHOT
55
105
320
215
645
190
Lock Button
Power Switch
VIDEO/
MEMORY
1 Remove the lens cap.
2 Open the LCD monitor fully. (੬ pg. 19)
3 Set the VIDEO/MEMORY Switch to
“MEMORY”.
4 Set the Power Switch to “REC” while pressing
down the Lock Button located on the switch.
● To change the Picture Quality, ੬ pg. 31, 34.
5 Press SNAPSHOT. The “PHOTO” indication
appears while the snapshot is being taken.
● To delete unwanted still images, refer to “Deleting
Files”. (੬ pg. 29)
● When you do not want to hear the shutter sound,
set “MELODY” to “OFF”. (੬ pg. 31, 33)
NOTE:
If shooting is not performed for approx. 5 minutes
when the Power Switch is set to “REC” and power
is supplied from the battery pack, the camcorder
shuts off automatically to save power. To perform
shooting again, push back and pull out the
viewfinder again or close and re-open the LCD
monitor.
D.S.C. PLAYBACK
EN
27
Normal Playback Of Images
You can view several different files stored in the
memory card at a time. This browsing capability
Images shot with the camcorder are
automatically numbered, then stored in
numerical order in the memory card.You can
view the stored images, one at a time, much like
flipping through a photo album.
1 Perform steps 1 – 3 in “Normal Playback Of
Images”.
2
2 Press INDEX. The
Selected file
6
Lock Button
1
Index Screen appears.
1
4
7
2
5
8
3
3 Press 4, 3, 1or 2to
move the frame to the
desired file.
6
9
4 Press SET. The
Power Switch
selected file is displayed.
VIDEO/
MEMORY
MENU
7
Index number
Removing On-Screen Display
2 Set the VIDEO/MEMORY Switch to
“MEMORY”.
1 Perform steps 1 – 3 in “Normal Playback Of
3 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
Images”.
2 Press MENU. The Menu Screen appears.
● A stored image is displayed.
and press SET. The ON SCREEN Menu
appears.
to display the next file.
4 Press 4or 3to select “OFF”, and press SET
or 2, then press MENU. The operation mode
indicator, folder/file number and battery
remaining power indicator disappear.
NOTE:
Images shot and stored on the card with another
device with resolutions other than “640 x 480” will
be displayed as thumbnails only. These thumbnail
images cannot be transferred to a PC.
● To display the indicators again, select “ON”.
Playback Zoom
Folder/file number
Available only with the remote control.
O N S C R E E N
(੬ pg. 25)
Auto Playback Of Images
You can run through all the images stored in
memory card automatically.
Operation mode indicator
1 Perform steps 1 – 3 in “Normal Playback Of
Images”.
2 Press 6to start Auto Playback.
● If you press 1during Auto Playback, files are
displayed in descending order.
● If you press 2during Auto Playback, files are
displayed in ascending order.
3 To end Auto Playback, press 7.
ADDITIONAL FEATURES FOR D.S.C.
EN
28
To protect all files stored in the memory card
Resetting The File Name
4 Press 4or 3to select “PROT.ALL”, and press
SET or 2. The PROTECT screen appears.
By resetting the file name, a new folder will be
made. The new files you are going to make will
be stored in the new folder. It is convenient to
separate the new files from previously made
files.
5 Press 4or 3to select “EXECUTE”, and
press SET.
● To cancel protection, select “RETURN”.
NOTES:
● If the “
” mark appears, the currently displayed
1 Perform steps 1 – 3 in “Normal Playback Of
file is protected.
Images”. (੬ pg. 27)
even protected files are deleted. If you do not want
to lose important files, transfer them to a PC and
save them.
2 Press MENU. The Menu Screen appears.
and press SET. The NO. RESET screen
appears.
To Remove Protection
Before doing the following, perform steps 1 – 3
in “Protecting Files”.
4 Press 4or 3to select “EXECUTE”, and
press SET. The new folder (such as
“101JVCGR”) will be made and the file name of
the next shot starts from DVC00001.
To remove protection from the currently
displayed file
NOTE:
If the file name reaches DVC09999, a new folder
(such as “101JVCGR”) will be made and the file
name will start again from DVC00001.
4 Press 4or 3to select “CURRENT”, and
press SET or 2. The PROTECT screen appears.
5 Press 1or 2to select the desired file.
6 Press 4or 3to select “EXECUTE”, and
Protecting Files
The Protect mode helps prevent the accidental
press SET.
● To cancel selection, select “RETURN”.
● Repeat steps 5 and 6 for all files you want to
remove protection.
erasure of files.
1 Perform steps 1 – 3 in “Normal Playback Of
To remove protection from all files stored in
the memory card
Images”. (੬ pg. 27)
2 Press MENU. The Menu Screen appears.
4 Press 4or 3to select “CANC.ALL”, and
3 Press 4, 3, 1 or 2to select “PROTECT”, and
press SET or 2. The PROTECT screen appears.
press SET. The PROTECT Menu appears.
5 Press 4or 3to select “EXECUTE”, and
To protect the currently displayed file
press SET.
● To cancel selection, select “RETURN”.
4 Press 4or 3to select
“CURRENT”, and press
SET or 2. The PROTECT
screen appears.
5 Press 1or 2to select
the desired file.
6 Press 4or 3to select
“EXECUTE”, and press
SET.
● To cancel protection,
select “RETURN”.
● Repeat steps 5 and 6 for
all files you want to
protect.
ADDITIONAL FEATURES FOR D.S.C.
EN
29
Deleting Files
Previously stored files can be deleted either one
at a time or all at once.
Setting Print Information (DPOF
Setting)
This camcorder is compatible with the DPOF
(Digital Print Order Format) standard in order to
support future systems such as automatic
printing.You can select one of the 2 print
information settings for images stored in the
memory card: “To Print All Still Images (One
Print For Each)” or “To Print By Selecting Still
Images And Number Of Prints”.
1 Perform steps 1 – 3 in “Normal Playback Of
Images” (੬ pg. 27).
2 Press MENU. The Menu Screen appears.
3 Press 4, 3, 1 or 2to select “DELETE”, and
press SET. The Menu appears.
To delete the currently displayed file
NOTE:
4 Press 4or 3to select
“CURRENT”, and press
SET or 2. The DELETE
screen appears.
If you load a memory card already set as shown
below in a printer compatible with DPOF, it will
make prints of the selected still images
automatically.
5 Press 1or 2to select
the desired file.
To Print All Still Images (One Print For Each)
6 Press 4or 3to select
“EXECUTE”, and press
SET.
● To cancel deletion, select
“RETURN”.
1 Perform steps 1 – 3 in “Normal Playback Of
Images”. (੬ pg. 27)
2 Press MENU. The Menu Screen appears.
● Repeat steps 5 and 6 for
all files you want to delete.
3 Press 4, 3, 1 or 2to
select “DPOF”, and press
SET. The DPOF Menu
appears.
NOTE:
If the “
” mark appears, the selected file is
4 Press 4or 3to select
“ALL 1”, and press SET or
2. The DPOF screen
appears.
protected and cannot be deleted.
4 Press 4or 3to select “ALL”, and press SET
or 2. The DELETE screen appears.
5 Press 4or 3to select
“EXECUTE”, and press
SET. The normal playback
screen appears.
5 Press 4or 3to select “EXECUTE”, and
press SET.
● To cancel deletion, select “RETURN”.
● To cancel selection, select
“RETURN”.
NOTES:
● Protected files (੬ pg. 28) cannot be deleted. To
delete them, remove protection first.
● Once files are deleted, they cannot be restored.
Check files before deleting.
CAUTION:
Do not remove the memory card or perform any
other operation (such as turning off the camcorder)
during deletion. Also, be sure to use the provided
AC Adapter, as the memory card may be corrupted
if the battery becomes exhausted during deletion. If
the memory card becomes corrupted, initialize it.
(੬ pg. 30)
ADDITIONAL FEATURES FOR D.S.C.
EN
30
To Print By Selecting Still Images And
To Reset The Number Of Prints
Number Of Prints
1 Perform steps 1 – 3 in “To Print All Still
Images (One Print For Each)”. (੬ pg. 29)
1 Perform steps 1 – 3 in “To Print All Still
2 Press 4or 3to select “RESET”, and press
Images (One Print For Each)”. (੬ pg. 29)
SET. The DPOF screen appears.
2 Press 4or 3to select
“CURRENT”, and press
SET or 2. The DPOF
screen appears.
3 Press 4or 3to select “EXECUTE”, and
press SET. The normal playback screen
appears.
● To cancel selection, select “RETURN”.
● The number of prints is reset to 0 for all still
images.
3 Press 1or 2to select
the desired file.
CAUTION:
(00), and press SET.
While performing the above, never disconnect
power, as this may cause the memory card to be
corrupted.
5 Select the number of
prints by pressing 3to
increase the number, or 4
to decrease the number,
and press SET.
● Repeat steps 3 through 5
for the desired number of
prints.
● The number of prints can be set up to 15.
● To correct the number of prints, select the image
again and change the number.
Initializing A Memory Card
You can initialize a memory card any time.
After initializing, all files and data stored in the
memory card, including those which have been
protected, are cleared.
1 Set the VIDEO/MEMORY Switch to
“MEMORY”.
6 Press 4or 3to select
“RETURN”, and press
SET. The “SAVE?”
appears.
● If you did not change any
settings in step 3 through
5, the DPOF Menu
reappears.
2 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
3 Press MENU. The Menu Screen appears.
4 Press 4, 3, 1 or 2to
select “FORMAT”, and
press SET.The FORMAT
screen appears.
7 Press 4or 3to select “EXECUTE” to save
the setting you have just made, and press SET.
● To cancel selection, select “CANCEL”.
5 Press 4or 3to select
“EXECUTE”, and press
SET.The memory card is
initialized.
● When initialization is finished, “NO IMAGES
STORED” appears.
● To cancel initialization, select “RETURN”.
CAUTION:
Do not perform any other operation (such as
turning off the camcorder) during initialization.
Also, be sure to use the provided AC Adapter, as
the memory card may be corrupted if the battery
becomes exhausted during initialization. If the
memory card becomes corrupted, initialize it.
MENUS FOR DETAILED ADJUSTMENT
EN
31
Video Recording and D.S.C. Recording Menus
Changing The Menu Settings
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of
the more detailed camcorder settings.
(੬ pg. 31 – 35)
Selected menu icon
FUNCTION (
੬
pg. 32)
SETTING (੬ pg. 32)
DISPLAY (੬ pg. 34)
DSC (੬ pg. 34)
WIPE/FADER
EF
1
3
2
Lock Button
1) Press 4, 3, 1 or 2to
select the desired
● Example: WIPE/FADER
Menu
WB
VIDEO/
MEMORY
2) Press 3or 4to select the desired parameter
and press SET or 2. Selection is complete.
● The “3” indicator shows the setting that is
currently saved inside the camcorder’s memory.
● Press 1whenever you want to cancel or return to
the previous Menu Screen.
Power Switch
4
MENU
1 For Video and D.S.C. Recording Menus:
● Set the VIDEO/MEMORY Switch to “VIDEO” or
“MEMORY”.
● Set the Power Switch to “REC” while pressing
down the Lock Button located on the switch.
● Set the recording mode to “ ”. (੬ pg. 15)
3) Press MENU. The Menu Screen closes.
NOTE:
Repeat the procedure if you wish to set other
function menus.
Video Playback Menu
For Video Playback Menu:
REC MODE (੬ pg. 35)
● Set the VIDEO/MEMORY Switch to “VIDEO”.
● Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
● For D.S.C. Playback Menu, refer to “D.S.C.
PLAYBACK” (੬ pg. 27).
SOUND MODE (੬ pg. 35)
NARRATION (੬ pg. 35)
BRIGHT (੬ pg. 35)
DATE/TIME (੬ pg. 35)
ON SCREEN (੬ pg. 35)
2 Open the LCD monitor fully. (੬ pg. 19)
3 Press MENU. The Menu Screen appears.
TIME CODE (
੬
pg. 35)
Selected menu icon
4 Press 4, 3, 1 or 2to select the desired
function, and press SET. The selected function
menu appears.
Example: REC MODE
Menu
1) Press 3or 4to
select the desired
parameter and press
SET or 2. Selection is
complete.
REC MODE
Screen for Video and
Screen for Video
D.S.C. Recording Menu Playback Menu
REC MODE
FUNCTION
● Repeat the procedure if
you wish to set other
function menus.
“3” indicator
● The “3” indicator shows
the setting that is
currently saved inside
the camcorder’s
memory.
● Press 1whenever you
want to cancel or return
5 Setting procedure hereafter depends on the
SP
LP
selected function.
NOTES:
● You cannot enter Menu Screen during recording.
● Certain functions cannot be set in the Video or
D.S.C. Recording Menus. These icons will be
displayed in grey/white.
to the previous Menu Screen.
2) Press MENU. The Menu Screen closes.
MENUS FOR DETAILED ADJUSTMENT
EN
32
Recording Menus
SETTING
The following settings are effective when the
Power Switch is set to “REC”.
[ ] = Factory-preset
FUNCTION
The following menu settings can be changed
only when the Power Switch is set to “REC”.
[ ] = Factory-preset
REC MODE
[SP]*: To record in the SP (Standard Play) mode
LP: Long Play—more economical, providing 1.5
times the recording time.
WIPE/FADER
* SP indicator does not appear on the screen.
NOTES:
EFFECT
● Audio Dubbing (੬ pg. 45) and Insert Editing
(੬ pg. 45) are possible on tapes recorded in the
SP mode.
(੬ pg. 41), “Program AE, Effects and Shutter
Effects”
● If the recording mode is switched, the playback
picture will be blurred at the switching point.
● It is recommended that tapes recorded in the LP
mode on this camcorder be played back on this
camcorder.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there
may be momentary pauses in the sound.
PROGRAM AE
(੬ pg. 41), “Program AE, Effects and Shutter
Effects”
SHUTTER
(੬ pg. 41), “Program AE, Effects and Shutter
Effects”
SOUND MODE
EXPOSURE
[12BIT]: Enables video recording of stereo
sound on four separate channels, and is
recommended for use when performing Audio
Dubbing. (Equivalent to the 32 kHz mode of
previous models)
(੬ pg. 38), “Exposure Control”
W. BALANCE
(੬ pg. 39), “White Balance Adjustment”
16BIT: Enables video recording of stereo sound
on two separate channels. (Equivalent to the
48 kHz mode of previous models)
TELE MACRO
[OFF]: Disables the function.
ON: When the distance to the subject is less
than 1 m (3.3 ft), set “TELE MACRO” to “ON”.
You can shoot a subject as large as possible at a
distance of approx. 40 cm (1.4 ft).
Depending on the zoom position, the lens may go
out of focus.
DIS*
OFF: Disables the function.
[ON
]: To compensate for unstable images
caused by camera-shake, particularly at high
magnification.
NOTES:
● Accurate stabilization may not be possible if hand
shake is excessive, or depending on the shooting
condition.
● The “
” indicator blinks or goes out if the
Stabilizer cannot be used.
● Switch off this mode when recording with the
camcorder on a tripod.
* Available only when the VIDEO/MEMORY Switch
is set to “VIDEO”.
MENUS FOR DETAILED ADJUSTMENT
EN
33
SYSTEM
SNAP/SLOW*
[SNAP]: Snapshot mode
SLOW : Live Slow mode
For details on the procedure, refer to “Live Slow”
(੬ pg. 36) and “Snapshot (Record Still Image
On Tape)” (੬ pg. 37).
* Available only when the VIDEO/MEMORY Switch
is set to “VIDEO”.
The “ SYSTEM” functions which are set when
the Power Switch is set to “REC” are also
applied when the Power Switch is set to “PLAY”.
[ ] = Factory-preset
MELODY
OFF: Even though not heard while shooting,
shutter sound is recorded on the tape.
[ON]: A melody sounds when any operation is
performed. It also activates the shutter sound
effect. (੬ pg. 26, 37)
ZOOM*
[32X]: When set to “32X” while using digital
zoom, the zoom magnification will reset to 32X
since digital zoom will be disengaged.
64X*: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 32X (the optical zoom
limit), to a maximum of 64X digital magnification.
800X*: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 32X (the optical zoom
limit), to a maximum of 800X digital
CAM RESET
[RETURN]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-
preset.
PRIORITY
[LCD]: The image is displayed on the LCD
monitor when the viewfinder is pulled out while
the LCD monitor is opened.
FINDER: The image is displayed in the
viewfinder when the viewfinder is pulled out
while the LCD monitor is opened.
magnification.
* Available only when the VIDEO/MEMORY Switch
is set to “VIDEO”.
GAIN UP
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
[AGC]: The overall appearance may be grainy,
REMOTE
OFF: Disables the remote control operations.
[ON]: Enables the remote control operations.
but the image is bright.
AUTO
:The shutter speed is automatically
adjusted. Shooting a subject in low or poor
lighting at slow shutter speed provides a brighter
image than in the AGC mode, but the subject’s
movements are not smooth or natural. The
overall appearance may be grainy. While the
shutter speed is being automatically adjusted,
“
” is displayed.
WIND CUT
[OFF]: Disengages the function.
ON : Helps cut down on noise created by
wind. The “ ” indicator appears. The quality of
the sound will change. This is normal.
MENUS FOR DETAILED ADJUSTMENT
EN
34
DISPLAY
DEMO MODE
OFF: Automatic demonstration will not take
place.
● The following menu settings can be changed only
when the Power Switch is set to “REC”.
● The DISPLAY settings except “BRIGHT” and
“LANGUAGE” are effective only for shooting.
[ ] = Factory-preset
[ON]: Demonstrates certain functions such as
Wipe/Fader and Effects, etc., and can be used
to confirm how these functions operate.
Demonstration starts in the following cases:
● When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
● With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch is set to “REC”.
BRIGHT
੬ pg. 17, “Brightness Adjustment Of The
Display”
CLOCK ADJ.
● Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will
resume.
੬ pg. 16, “Date/Time Settings”
LANGUAGE
/
/
/ [ENGLISH] / FRANÇAIS /
ESPAÑOL / PORTUGUÊS
The language setting can be changed.
(੬ pg. 16)
NOTES:
● If a cassette is in the camcorder, the
demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the
DATE/TIME
[OFF]: The date/time does not appear.
ON: The date/time is always displayed.
● The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote
control. (੬ pg. 23, 42)
DSC
[ ] = Factory-preset
QUALITY
ON SCREEN
[FINE] / STANDARD
The Picture Quality mode can be selected to
best match your needs. Two Picture Quality
LCD: Keeps the camcorder’s display (except the
date, time and time code) from appearing on the
connected TV screen.
[LCD/TV]: Makes the camcorder’s display
appear on screen when the camcorder is
connected to a TV.
modes are available: FINE (
) and
STANDARD (
) (in order of quality).
NOTE:
The number of storable images depends on the
selected picture quality as well as the composition
of the subjects in the images and the type of
memory card being used. (੬ pg. 26)
TIME CODE
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder
and on the connected TV. Frame numbers are
not displayed during recording. (੬ pg. 20)
REC SELECT
[
(TAPE)]: When Snapshot recording is
performed with the VIDEO/MEMORY Switch set
to “VIDEO”, still images are recorded only onto
the tape.
/
(TAPE/CARD): When Snapshot
recording is performed with the VIDEO/
MEMORY Switch set to “VIDEO”, still images
are recorded not only onto the tape but also in
the memory card (640 x 480 pixels).
MENUS FOR DETAILED ADJUSTMENT
EN
35
BRIGHT
Playback Menus
[ ] = Factory-preset
੬ pg. 17, “Brightness Adjustment Of The
Display”
SOUND MODE and NARRATION
DATE/TIME
During tape playback, the camcorder detects the
sound mode in which the recording was made,
and plays the sound back. Select the type of
sound to accompany your playback picture.
According to the menu access explanation on
page 31, select “SOUND MODE” or
[OFF]: The DATE/TIME does not appear.
ON SCREEN
OFF / [LCD] / LCD/TV
When set to “OFF”, the camcorder’s display
disappears.
“NARRATION” from the Menu Screen and set it
to the desired parameter.
TIME CODE
[OFF] / ON
੬ pg. 20, “Time Code”
The setting below are effective only for video
playback except “BRIGHT” and “REC MODE”.
The parameters (except “OFF” in ON SCREEN,
SOUND MODE and NARRATION settings) are
the same as in the description on page 32, 34.
REC MODE
[SP]* / LP
Allows you to set the video recording mode (SP
or LP) depending on your preference. It is
recommended you use “REC MODE” in VIDEO
Menu when using this camcorder as a recorder
during dubbing. (੬ pg. 42, 43)
*SP indicator does not appear on the screen.
SOUND MODE
[STEREO
]: Sound is output on both “L” and
“R” channels in stereo.
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
NARRATION
[OFF]: Original sound is output on both “L” and
“R” channels in stereo.
ON: Dubbed sound is output on both “L” and “R”
channels in stereo. (੬ pg. 45)
MIX: Original and dubbed sounds are combined
and output in stereo on both “L” and “R”
channels.
FEATURES FOR RECORDING
EN
36
LED Light
LED Light can be used to
brighten the subject in the dark
place during video recording or
D.S.C. shooting.
Wide Mode
This camcorder allows you to choose the type of
image output format for video recording.
1 Set the Power Switch to “REC”.
2 Press 16:9 button repeatedly to choose your
1 Press LIGHT repeatedly to
selection.
change the setting.
LED Light
appears.)
OFF: Turns off the light.
ON: The light is on always. (
AUTO: The light turns on automatically when
dark. ( appears.)
4 : 3
16 : 9
2 Press the Recording Start/Stop Button to
start video recording or SNAPSHOT to shoot a
still image.
[4:3]: Records with no change in the screen
ratio. For playback on a TV with a normal screen
ratio. When using this mode on a TV with a
manual.
16:9: For playback on TVs with an aspect ratio of
16:9. Naturally expands the image to fit the
screen without distortion. The “16:9” indicator
appears. When using this mode, refer to your
wide-screen TV’s instruction manual. During
playback/recording on 4:3 TVs/LCD monitor/
viewfinder, the image is elongated vertically.
[ ] = Factory-preset
NOTES:
●
Be careful not to point the LED Light directly to eyes.
● If the light does not reach the subject when the
LED Light setting is “ON”, the Night-Alive function
will be activated, and makes it possible to shoot
the subject brighter.
● There is a difference in the brightness of the
images shot between the center area which is
illuminated by the LED Light and the surrounding
areas (which will be darker).
● Since subjects are shot at a reduced shutter
speed when the LED Light setting is “ON”, they
will appear slightly blurred.
NOTE:
Live Slow
This feature is useful for recording or playing
back precious or hard-to-see moments at a slow
speed. Sound is recorded and played back in
real time.
Available only when the VIDEO/MEMORY Switch is
set to “VIDEO”.
1 Set the VIDEO/MEMORY Switch to “VIDEO”.
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Set “SNAP/SLOW” to “SLOW”.
(੬ pg. 31, 33) The Live Slow indicator “
”
appears.
4 Press SNAPSHOT (SLOW) during recording
or playback.
● The moving pictures are divided into four
frames. They are recorded or played back for
1.5 seconds, and then normal recording or
playback resumes.
● This feature is effective when the recording
mode selection is set to both “ ” or “ ”.
NOTE:
Available only when the VIDEO/MEMORY Switch is
set to “VIDEO”.
FEATURES FOR RECORDING
EN
37
Motor Drive Mode
an effect similar to serial photography. (Interval
between still images: approx. 1 second)
● The Motor Drive mode is disabled when “REC
SELECT” is set to “
Night-Alive
Makes dark subjects or areas even brighter than
they would be under good natural lighting.
Although the recorded image is not grainy, it may
look as if it is strobing due to the slow shutter
speed.
/
”. (੬ pg. 34)
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as
close as approx. 5 cm (2") to the subject) to
infinity.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Press NIGHT so that the Night-Alive indicator
“
” appears.
● The shutter speed is automatically adjusted to
provide up to 30 times sensitivity.
However, correct focus may not be obtained
depending on the shooting condition. In this
case, use the manual focus mode.
● “ ” appears beside “
” while the shutter speed
is being automatically adjusted.
To deactivate Night-Alive
Press NIGHT again so that the Night-Alive
indicator disappears.
1 Set the Power Switch
to “REC”.
2 Set the recording mode
NOTES:
to “ ”. (੬ pg. 15)
● During Night-Alive, “GAIN UP” or “DIS” in
SETTING Menu (੬ pg. 32, 33) cannot be
activated.
manual focus indicator
appears.
● Night-Alive cannot be activated simultaneously
with “SNOW” or “SPORTS” of “PROGRAM AE”, or
all modes of “SHUTTER”. (੬ pg. 41).
● During Night-Alive, it may be difficult to bring the
camcorder into focus. To prevent this, use of a
tripod is recommended.
Manual focus
indicator
4 Press 1or 2to focus
on a subject.
● When the focus level cannot be adjusted any
further or closer, “ ” or “ ” will blink.
5 Press SET. Focus adjustment is complete.
To reset to Auto Focus
Press FOCUS twice.
Snapshot (Record Still Image On
Tape)
This feature lets you record still images that look
like photographs onto a tape.
Manual focus is recommended in situations
listed below.
● When two subjects overlap in the same scene.
● When illumination is low.*
● When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
color wall, or a clear, blue sky.*
● When a dark object is barely visible in the LCD
monitor or the viewfinder.*
● When the scene contains minute patterns or
identical patterns that are regularly repeated.
● When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
● When shooting a scene with a high-contrast
background.
1 Set the VIDEO/MEMORY Switch to “VIDEO”.
2 Set the Power Switch to “REC”.
3 Set the recording mode to “ ”. (੬ pg. 15)
4 Set “SNAP/SLOW” to “SNAP”. (੬ pg. 31, 33)
5 Press SNAPSHOT.
● There is the sound effect of a shutter closing.
● The “PHOTO” indication appears and a still image
will be recorded for approx. 5 seconds, then the
camcorder re-enters the Record-Standby mode.
● You can perform Snapshot also during recording.
A still image will be recorded for approx.
5 seconds, then the normal recording resumes.
● Snapshot is effective when the recording mode
selection is set to both “ ” or “ ”.
* The following low-contrast warnings appear
blinking:
,
,
and
.
● Snapshot mode cannot be used when the 16:9
Wide mode (16:9 indicator) is selected.
FEATURES FOR RECORDING
EN
38
Exposure Control
Manual exposure control is recommended in the Like the pupil of the human eye, the iris
following situations:
● When shooting using reverse lighting or when the
background is too bright.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When the background is overly dark or the subject
is bright.
contracts in well-lit environments to keep too
much light from entering, and dilates in dim
environments to allow in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so its
size in the LCD monitor or the viewfinder
changes), such as when the subject is backing
away.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When shooting objects under a spotlight.
● When zooming.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Set “EXPOSURE” to “MANUAL” in
FUNCTION Menu. (੬ pg. 31)
● The exposure control menu appears.
1 Set the Power Switch to “REC”.
4 To brighten the image, press 3.To darken the
image, press 4. (maximum 6)
● +3 exposure has the same effect as the backlight
compensation. (੬ pg. 39)
● –3 exposure has the same effect as when
“PROGRAM AE” is set to “SPOTLIGHT”.
(੬ pg. 41)
3 Set “EXPOSURE” to “MANUAL” in
FUNCTION Menu. (੬ pg. 31)
● The exposure control menu appears.
monitor or the viewfinder, then press and hold
SET or 2for over 2 seconds. The “ ” indication
appears.
Operation Mode
Video
Memory
Exposure Level
0
1
2
3
4
5
6
0.3EV
0.7EV
1.0EV
1.3EV
1.7EV
2.0EV
5 Press SET or 2. The iris is locked.
6 Press MENU. The Menu Screen closes. The
“
” indicator appears.
To return to automatic iris control
Select “AUTO” in step 3.
● The exposure control indicator and “
disappear.
”
5 Press SET or 2. Exposure adjustment is
complete.
To lock the exposure control and the iris
After step 3, adjust the exposure by pressing 3
or 4. Then lock the iris in steps 4 – 6. For
automatic locking, select “AUTO” in step 3. The
exposure control and the iris become automatic.
To return to automatic exposure control
Select “AUTO” in step 3.
NOTES:
● You cannot use the manual exposure control at
the same time when “PROGRAM AE” is set to
“SPOTLIGHT” or “SNOW” (੬ pg. 41), or with the
backlight compensation.
● If the adjustment does not cause any visible
change in brightness, set “GAIN UP” to “AUTO”.
(੬ pg. 31, 33)
FEATURES FOR RECORDING
EN
39
NOTES:
Backlight Compensation
Backlight compensation brightens the subject
● You cannot use the Spot Exposure Control at the
same time with following functions.
• “16:9” in “WIDE MODE” (੬ pg. 36)
• Digital Zoom (੬ pg. 20)
● Depending on the shooting location and condition,
optimum result may not be attained.
quickly.
With simple operation, backlight compensation
feature brightens the dark subject portion by
increasing the exposure.
1 Set the Power Switch to “REC”.
2 Press BACKLIGHT so that the Backlight
Compensation indicator “ ” appears.
The white balance refers to the correctness of
color reproduction under various lighting. If the
white balance is correct, all other colors will be
accurately reproduced.
The white balance is usually adjusted
automatically. However, more advanced
camcorder operators control this function
manually to achieve a more professional color/
tint reproduction.
To cancel Backlight Compensation
Press BACKLIGHT twice so that the “
indicator disappears.
”
NOTE:
Using Backlight Compensation may cause the light
around the subject to become too bright and the
subject to become white.
Spot Exposure Control
Selection of a spot metering area enables more
one of the three metering areas on the LCD
monitor/viewfinder.
To change the setting
Set “W. BALANCE” to the desired mode.
(੬ pg. 31)
● The selected mode indicator except “AUTO”
appears.
[AUTO]: White balance is adjusted
automatically.
1 Set the Power Switch to “REC”.
MWB: Adjust the white balance manually
when shooting under various types of lighting.
(੬ “Manual White Balance Adjustment”, pg. 40)
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
[ ] = Factory-preset
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Press BACKLIGHT twice so that the Spot
Exposure Control indicator “ ” appears.
● A spot metering area frame appears at the
center of the LCD monitor/viewfinder.
4 Press 2or 1to select the desired spot
To return to automatic white balance
Set “W. BALANCE” to “AUTO”. (੬ pg. 31)
metering area frame.
5 Press SET.
● Spot Exposure Control is engaged.
● Exposure is adjusted to make the brightness of
the selected area most appropriate.
To lock the iris
After step 4, press and hold SET over 2
seconds.The “ ” indication appears and the iris
is locked.
To cancel Spot Exposure Control
Press BACKLIGHT once so that the “
”
indicator disappears.
FEATURES FOR RECORDING
EN
40
Manual White Balance Adjustment
Adjust the white balance
manually when shooting
under various types of
lighting.
Wipe Or Fader Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next.
Wipe or Fader works when video recording is
started or stopped.
1 Set the Power Switch
to “REC”.
White paper
1 Set the VIDEO/MEMORY Switch to “VIDEO”.
2 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Hold a sheet of plain white paper in front of
the subject. Adjust zoom or position yourself so
that the white paper fills the screen.
3 Set the recording mode to “ ”. (੬ pg. 15)
4 Set “ ” in FUNCTION Menu. (੬ pg. 31)
● The WIPE/FADER menu disappears and the
effect is reserved.
4 Select “MWB” in “
W. BALANCE” menu
(੬ pg. 31), then press and hold SET or 2until
● The selected effect indicator appears.
begins blinking.
5 Press the Recording Start/Stop Button to
● When the setting is completed,
stops blinking.
activate the Fade-in/out or Wipe-in/out.
5 Press SET or 2to engage the setting.
To deactivate the selected effect
Select “OFF” in step 4. The effect indicator
disappears.
6 Press MENU. The Menu Screen closes and
the Manual White Balance indicator
displayed.
is
NOTE:
NOTES:
You can extend the length of a Wipe or Fader by
pressing and holding the Recording Start/Stop
Button.
● In step 3, it may be difficult to focus on the white
paper. In such a case, adjust focus manually.
(੬ pg. 37)
● A subject can be shot under various types of
lighting conditions indoors (natural, fluorescent,
candlelight, etc.). Because the color temperature
is different depending on the light source, the
subject tint will differ depending on the white
balance settings. Use this function for a more
natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off or
the battery removed.
WIPE/FADER
OFF: Disables the function. (Factory-preset)
WHITE
BLACK
SLIDE
: Fade in or out with a white screen.
: Fade in or out with a black screen.
:Wipe in from right to left, or wipe out
from left to right.
SCROLL
: The scene wipes in from the
bottom to the top of a black screen, or wipes out
from top to bottom, leaving a black screen.
FEATURES FOR RECORDING
EN
41
PROGRAM AE
Program AE, Effects And Shutter
Effects
OFF: Disables the function. (Factory-preset)
SPORTS
(Variable Shutter Speed: 1/250 – 1/4000):
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable
slow-motion playback. The faster the shutter
speed, the darker the picture becomes. Use the
shutter function under good lighting conditions.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 15)
3 Set “EFFECT”, “PROGRAM AE” or
“SHUTTER” in FUNCTION Menu. (੬ pg. 31)
● The EFFECT, PROGRAM AE or SHUTTER menu
disappears and the selected effect is activated.
● The selected effect indicator appears.
SNOW
: Compensates for subjects that may
otherwise appear too dark when shooting in
extremely bright surroundings such as in the
snow.
To deactivate the selected effect
Select “OFF” in step 3. The effect indicator
disappears.
SPOTLIGHT
: Compensates for subjects that
may otherwise appear too bright when shooting
under extremely strong direct lighting such as
spotlights.
NOTES:
● Program AE, Effects and Shutter Effects can be
changed during Record-Standby.
● Some modes of Program AE and Shutter Effects
cannot be used during Night-Alive.
● When a subject is too bright or reflective, a
vertical streak may appear (smear
phenomenon). Smear phenomenon tends to
occur when “SPORTS” or any mode of
“SHUTTER 1/500 – 1/4000” is selected.
TWILIGHT
: Makes evening scenes look
more natural. White Balance (੬ pg. 39) is
automatically set to “ ”, but can be changed to
your desired setting. When Twilight is chosen,
the camcorder automatically adjusts the focus
from approx. 10 m (32 ft) to infinity. From less
than 10 m, adjust the focus manually.
EFFECT
SHUTTER
OFF: Disables the function. (Factory-preset)
OFF: Disables the function. (Factory-preset)
SEPIA
: Recorded scenes have a brownish
SHUTTER 1/60: The shutter speed is fixed
at 1/60th of a second. Black bands that usually
appear when shooting a TV screen become
narrower.
tint like old photos.
MONOTONE
films, your footage is shot in B/W.
: Like classic black and white
CLASSIC*
effect.
: Gives recorded scenes a strobe
SHUTTER 1/100: The shutter speed is
fixed at 1/100th of a second. The flickering that
STROBE*
of consecutive snapshots.
* Not available for still image recording.
:Your recording looks like a series occurs when shooting under a fluorescent light
or mercury-vapour lamp is reduced.
SHUTTER 1/500/SHUTTER 1/4000: These
settings allow fast-moving images to be
captured one frame at a time, for vivid, stable
slow-motion playback by fixing shutter speed
variables. Use these settings when an automatic
adjustment does not work well, using SPORTS
mode. The faster the shutter speed, the darker
the picture becomes. Use the shutter function
under good lighting conditions.
EDITING
EN
42
To use this camcorder as a player
Dubbing To A VCR
1 Following the illustrations, connect the
camcorder and the VCR’s input connectors.
3 At the point you want to start dubbing, start
recording on the VCR. (Refer to the VCR’s
instruction manual.)
4 To stop dubbing, stop recording on the VCR,
To AV
connector
then stop playback on the camcorder.
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 15)
Audio/Video cable
(provided)
● To choose whether or not the following displays
appear on the connected TV
• Date/time
Set “DATE/TIME” to “ON” or “OFF”.
(੬ pg. 31, 35) Or, press DISPLAY on the
remote control to turn on/off the date indication.
• Time code
Set “TIME CODE” to “OFF” or “ON”.
(੬ pg. 31, 35)
TV
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
TV”. (੬ pg. 31, 35)
VCR
1Yellow to VIDEO IN
2Red to AUDIO R IN
3White to AUDIO L IN
EDITING
EN
43
NOTES:
Dubbing To Or From A Video Unit
Equipped With A DV Connector
(Digital Dubbing)
It is also possible to copy recorded scenes from
the camcorder onto another video unit equipped
with a DV connector. Since a digital signal is
sent, there is little, if any, image or sound
deterioration.
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 15)
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 4. If
this occurs, turn off the power and make
connections again.
● If “Playback Zoom” (੬ pg. 25) or “Playback
Special Effects” (੬ pg. 25) is attempted or
SNAPSHOT is pressed during playback, only the
original playback image recorded on the tape is
output from the DV IN/OUT connector.
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U or VC-VDV206U DV
cable.
To use this camcorder as a recorder
To DV IN/OUT
1 Make sure all units are turned off.
2 Connect this camcorder to a video unit
equipped with a DV output connector using a DV
cable as shown in the illustration.
3 Set the camcorder’s Power Switch to “PLAY”.
4 Set “REC MODE” to “SP” or “LP”. (੬ pg. 35)
DV cable (optional)
To DV IN/OUT
Core filter
6 Press the Recording Start/Stop Button to
engage the Record-Pause mode.
• The “
” indication appears on the
DV IN
screen.
7 At the point you want to start dubbing, press
the Recording Start/Stop Button to start
dubbing. The
indication rotates.
8 Press the Recording Start/Stop Button again
Video unit equipped with DV connector
to stop dubbing. The
rotating.
indication stops
To use this camcorder as a player
9 Press 7to return to the normal playback
mode.
1 Make sure all units are turned off.
NOTE:
2 Connect this camcorder to a video unit
equipped with a DV input connector using a DV
cable as shown in the illustration.
Digital Dubbing is performed in the sound mode
recorded on the original tape, regardless of the
current “SOUND MODE” setting. (੬ pg. 32)
3 Start playback on the camcorder. (੬ pg. 21)
4 At the point you want to start dubbing, start
recording on the video unit. (Refer to the video
unit’s instruction manual.)
5 To stop dubbing, stop recording on the video
unit, then stop playback on this camcorder.
EDITING
EN
44
[A] Using USB cable
It is possible to transfer still images stored on a
memory card to a PC.
Connection To A Personal Computer
[A] Using USB cable [B] Using DV cable
OR
[B] Using DV cable
It is also possible to transfer still/moving images
to a PC with a DV connector by using the
provided software, software equipped with the
PC or commercially available software.
If you are using a Windows® XP, you can use
Windows® Messenger to conduct video
conferences over the Internet, using a
camcorder. For details, refer to the help for the
Windows® Messenger.
To DV IN/OUT
To USB
NOTES:
● Refer to “SOFTWARE INSTALLATION AND USB
CONNECTION GUIDE” for the bundled software
and drivers.
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 15)
● Never connect the USB cable and the DV
cable simultaneously to the camcorder.
Connect only the cable you wish to use to the
camcorder.
● When using a DV cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U DV
cable depending on the type of DV connector
(4 or 6 pins) on the PC.
Core filter
Core filter
USB cable
(provided)
DV cable
(optional)
Core filter
To USB
connector
To DV connector
● If the PC connected to the camcorder via the USB
cable is not powered, the camcorder does not
enter the USB mode.
● The date/time information cannot be captured into
the PC.
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with a DV connector-equipped capture board.
● The system may not work properly depending on
the PC or capture board you are using.
PC with DV connector
PC
When connecting the camcorder to a PC
using a DV cable, make sure to follow the
procedure below. Connecting the cable
incorrectly may cause malfunctions to the
camcorder and/or the PC.
“USB” and/or “
” appears on the LCD
monitor while the PC is accessing data in the
camcorder or the camcorder is transferring a
file to the PC.
NEVER disconnect the USB cable while
● Connect the DV cable first to the PC, and then
to the camcorder.
“
” is displayed on the LCD
monitor since this can result in product
damage.
● Connect the DV cable (plugs) correctly
according to the shape of the DV connector.
EDITING
EN
45
Audio Dubbing
Insert Editing
You can record a new scene into a previously
The audio track can be customized only when
recorded in the 12-BIT and SP modes.
(੬ pg. 32)
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and out points. The original audio remains
unchanged.
● Use the provided remote control.
Speaker
● Use the provided remote control.
NOTES:
● Before performing the following steps, make sure
that “TIME CODE” for DISPLAY in both Recording
and Playback Menus is set to “ON”.
(੬ pg. 31, 34, 35)
● Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
START/
STOP
PAUSE
PLAY
STOP
Stereo Microphone
REW
INSERT
1 Play back the tape, locate the Edit-Out point
this point. (੬ pg. 20)
A.DUB
1 Play back the tape to locate the point where
editing will start, then press PAUSE (8).
2 Press REW (1) until the Edit-In point is
located, then press PAUSE (8).
2 While holding A. DUB ( ) on the remote
control, press PAUSE (8). The “8 ” indicator
appears.
3 Press and hold INSERT ( ) on the remote
control, then press PAUSE (8). The “8
”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
3 Press PLAY (3), then begin “narrating”.
Speak into the microphone.
● To pause dubbing, press PAUSE (8).
4 Press START/STOP to begin editing.
● Confirm the insert at the time code you checked in
step 1.
● To pause editing, press START/STOP. Press it
again to resume editing.
4 To end Audio Dubbing, press PAUSE (8),
then STOP (7).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”.
(੬ pg. 31, 35)
5 To end Insert Editing, press START/STOP,
then STOP (7) on the remote control.
NOTES:
NOTES:
● Sound is not heard from the speaker during Audio
Dubbing.
● Program AE, Effects and Shutter Effects
(੬ pg. 41) can be used to spice up the scenes
being edited during Insert Editing.
● During Insert Editing, the date and time
information changes.
● When editing onto a tape that was recorded at
12-BIT, the old and new soundtracks are recorded
separately.
● If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
● If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the
TV, or turn down the TV’s volume.
● If you change from 12-BIT to 16-BIT in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-BIT recording began.
● If you perform Insert Editing onto a blank space
on the tape, the audio and video may be
disrupted. Make sure you only edit recorded
areas.
● During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops. (੬ pg. 49)
● During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes
recorded in 16-BIT audio or a blank portion, Audio
Dubbing stops.
TROUBLESHOOTING
EN
46
If, after following the steps in the chart below, the
problem still exists, please consult your nearest
JVC dealer.
The LCD monitor or viewfinder indications
● Effects and “DIS” functions that cannot be used
together are selected at the same time.
➜Re-read the sections covering Effects and “DIS”.
(੬ pg. 31, 32, 41)
device. External noise and interference (from a
TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery pack,
AC Adapter, etc.) and wait a few minutes; and
then re-connect it and proceed as usual from
the beginning.
Digital Zoom does not work.
● 32X optical zoom is selected.
➜Set “ZOOM” to “64X” or “800X”. (੬ pg. 33)
● The VIDEO/MEMORY Switch is set to
“MEMORY”.
➜Set the VIDEO/MEMORY Switch to “VIDEO”.
Power
Video and D.S.C. Playback
No power is supplied.
The tape is moving, but there is no picture.
● The power is not connected properly.
➜Connect the AC Adapter securely. (੬ pg. 14)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-attach
it firmly. (੬ pg. 14)
● The battery is dead.
➜Replace the dead battery with a fully charged
one. (੬ pg. 14)
● Your TV has AV input terminals, but is not set to
its VIDEO mode.
➜Set the TV to the mode or channel appropriate for
video playback. (੬ pg. 23)
● The cassette holder cover is open.
➜Close the cassette holder cover. (੬ pg. 18)
there is no playback picture and the screen
becomes blue.
Video and D.S.C. Recording
Recording cannot be performed.
➜Clean the video heads with an optional cleaning
cassette. (੬ pg. 52)
● The tape’s erase protection tab is set to “SAVE”.
➜Set the tape’s erase protection tab to “REC”.
(੬ pg. 18)
Advanced features
● “TAPE END” appears.
➜Replace with new cassette. (੬ pg. 18)
● The cassette holder cover is open.
➜Close the cassette holder cover.
The focus does not adjust automatically.
● Focus is set to the Manual mode.
➜Set Focus to the Auto mode. (੬ pg. 37)
● The lens is dirty or covered with condensation.
➜Clean the lens and check the focus again.
(੬ pg. 50)
When shooting a subject illuminated by
bright light, vertical lines appear.
● This is not a malfunction.
Snapshot mode cannot be used.
When the screen is under direct sunlight
during shooting, the screen becomes red or
black for an instant.
● The Wide (16:9) mode (16:9 indicator) is
selected.
➜Disengage the 16:9 (16:9 indicator) Wide mode.
(੬ pg. 36)
● This is not a malfunction.
During recording, the date/ time does not
appear.
● “DATE/TIME” is set to “OFF”.
➜Set “DATE/TIME” to “ON”. (੬ pg. 31, 34)
TROUBLESHOOTING
EN
47
The color of Snapshot looks strange.
Files stored in the memory card cannot be
deleted.
● The light source or the subject does not include
white. Or there are various different light sources
behind the subject.
➜Find a white subject and compose your shot so
that it also appears in the frame. (੬ pg. 37, 40)
● Files stored in the memory card are protected.
memory card and delete them. (੬ pg. 28)
When the image is printed from the printer,
a black bar appears at the bottom of the
screen.
The image taken using Snapshot is too
dark.
● Shooting was performed under backlit conditions.
➜Press BACKLIGHT. (੬ pg. 39)
● This is not a malfunction.
➜
By recording with “DIS” de-activated (
੬
pg. 31, 32)
this can be avoided.
The image taken using Snapshot is too
bright.
When the camcorder is connected via the
DV connector, the camcorder does not
operate.
● The subject is too bright.
➜Set “ ” to “SPOTLIGHT”. (੬ pg. 41)
● The DV cable was plugged/unplugged with power
turned on.
White Balance cannot be activated.
➜Turn the camcorder’s power off and on again,
then operate it.
● The Sepia (SEPIA) or Monotone (MONOTONE)
mode is activated.
➜Disengage the Sepia (SEPIA) or Monotone
(MONOTONE) mode before setting White
Balance. (੬ pg. 41)
whitish.
● In places subject to low temperature, images
become dark due to the characteristics of the
LCD monitor. This is not a malfunction.
➜Adjust the brightness and angle of the LCD
monitor. (੬ pg. 17, 19)
the end of its service life, images on the LCD
monitor become dark.
The image looks like the shutter speed is
too slow.
● When shooting in the dark, the unit becomes
highly sensitive to light when “GAIN UP” is set to
“AUTO”.
➜If you want the lighting to look more natural, set
“GAIN UP” to “AGC” or “OFF”. (੬ pg. 31, 33)
➜Consult your nearest JVC dealer.
Other problems
Colored bright spots appear all over the
LCD monitor or the viewfinder.
The POWER/CHARGE lamp on the
camcorder does not light during charging.
● The LCD monitor and the viewfinder are made
with high-precision technology. However, black
spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder. These spots are not recorded on the
tape. This is not due to any defect of the unit.
(Effective dots: more than 99.99%)
● Charging is difficult in places subject to extremely
high/low temperatures.
➜To protect the battery, it is recommended to
charge it in places with a temperature of 10°C to
35°C (50°F to 95°F). (੬ pg. 51)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-attach
it firmly. (੬ pg. 13, 14)
The cassette will not load properly.
● The battery’s charge is low.
“SET DATE/TIME!” appears.
➜Install a fully charged battery. (੬ pg. 13)
● The date/time is not set.
➜Set the date/time. (੬ pg. 16)
● The built-in clock battery has run out and the
previously set date/time has been erased.
➜Consult your nearest JVC dealer for replacement.
TROUBLESHOOTING
EN
48
The memory card cannot be removed from
the camcorder.
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during
recording. Use an optional cleaning cassette.
(੬ pg. 52)
➜Push in the memory card a few more times.
(੬ pg. 18)
Picture does not appear on the LCD monitor.
PAUSED PLEASE WAIT
● The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
➜Push the viewfinder back in or set “PRIORITY” to
“LCD”. (੬ pg. 19, 31, 33)
● The LCD monitor’s brightness setting is too dark.
➜Adjust the brightness of the LCD monitor.
(੬ pg. 17)
Appears if condensation occurs. When this
indication is displayed, wait more than 1 hour
TAPE!
Appears if a tape is not loaded when the
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set
to “REC” and the VIDEO/MEMORY Switch is set
to “VIDEO”.
➜If the monitor is tilted upward 180 degrees, open
the monitor fully. (੬ pg. 19)
An error indication (01 – 04 or 06) appears.
● A malfunction of some kind has occured. In this
case the camcorder’s functions become
unusable.
TAPE END
➜੬ pg. 49.
Appears when the tape ends during recording or
playback.
The remote control does not work.
SET DATE/TIME!
● “REMOTE” is set to “OFF”.
➜Set “REMOTE” to “ON”. (੬ pg. 31, 33)
● The remote control does not point at the remote
sensor.
➜Point at the remote sensor. (੬ pg. 24)
● The remote control batteries are exhausted.
➜Replace the batteries with fresh ones. (੬ pg. 24)
● Appears when the date/time is not set.
(੬ pg. 16)
● The built-in clock battery has run out and the
previously set date/time has been erased.
Consult your nearest JVC dealer for
replacement.
Warning Indications
LENS CAP
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
Displays the battery remaining power.
Remaining power level
A. DUB ERROR!
Appears if Audio Dubbing is attempted on a
blank portion of a tape. (੬ pg. 45)
High
Exhausted
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power
turns off automatically.
A. DUB ERROR!
<CANNOT DUB ON A LP RECORDEDTAPE>
<CANNOT DUB ON A 16BIT RECORDING>
<CHECK TAPE’S ERASE PROTECTION
TAB>
● Appears if a tape is loaded.
● Blinks when no tape is loaded.
● Appears if Audio Dubbing is attempted on a
tape recorded in the LP mode. (੬ pg. 45)
● Appears if Audio Dubbing is attempted on a
tape recorded in 16-BIT audio. (੬ pg. 45)
● Appears if A. DUB ( ) on the remote control
is pressed when the erase protection tab is set
to “SAVE”. (੬ pg. 45)
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “REC”
and the VIDEO/MEMORY Switch is set to
“VIDEO”. (੬ pg. 15)
TROUBLESHOOTING
EN
49
INSERT ERROR!
NO IMAGES STORED
<CANNOT EDIT ON A LP RECORDED
TAPE>
<CHECK TAPE’S ERASE PROTECTION
TAB>
Appears if there are no image files stored in the
memory card when you attempt memory card
playback.
<CANNOT EDIT ON A BLANK PORTION>
CARD ERROR!
● Appears if Insert Editing is attempted on a
tape recorded in the LP mode. (੬ pg. 45)
● Appears if INSERT ( ) on the remote control
is pressed when the erase protection tab is set
to “SAVE”. (੬ pg. 45)
● Appears if Insert Editing is attempted on a
blank portion of a tape. (੬ pg. 45)
Appears when the camcorder does not
recognize the loaded memory card. Remove the
memory card once and insert it again. Repeat
these procedures until no indication appears. If
the indication still appears, the memory card is
corrupted.
CHECK CARD’S WRITE PROTECTION
SWITCH
MEMORY IS FULL
Appears when the memory card’s memory is full
and shooting is not possible.
Appears when you attempt to shoot digital still
images when the write protection tab on the SD
Memory Card is set to the “LOCK” position.
HDV
UNIT IN SAFEGUARD MODE
REMOVE AND REATTACH BATTERY OR DC
PLUG
Appears when pictures recorded in the HDV
format are detected. The pictures in the HDV
format cannot be played back with this
camcorder.
The error indications (01, 02 or 06) show what
type of malfunction has occured. When an error
indication appears, the camcorder turns off
automatically. Remove the power supply
(battery, etc.) and wait a few minutes for the
indication to clear. When it does, you can
resume using the camcorder. If the indication
remains, consult your nearest JVC dealer.
?
Appears when playing back a file that is not
not compatible with this camcorder.
COPY PROTECTED
Appears if dubbing of copyguarded signals is
attempted while this camcorder is being used as
a recorder.
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
The error indications (03 or 04) show what type
of malfunction has occured. When an error
indication appears, the camcorder turns off
automatically. Eject the cassette once and re-
insert it, then check if the indication clears.
When it does, you can resume using the
camcorder. If the indication remains, consult
your nearest JVC dealer.
MEMORY CARD!
Appears if there is no memory card loaded when
the SNAPSHOT Button is pressed while the
Power Switch is set to “REC” and the VIDEO/
MEMORY Switch is set to “MEMORY”.
PLEASE FORMAT
Appears when there is a problem with a memory
card and its memory is corrupt, or it has not
been initialized. Initialize the memory card.
(੬ pg. 30)
USER MAINTENANCE
EN
50
Cleaning The Camcorder
Before cleaning, turn off the camcorder and
remove the battery pack and AC Adapter.
To clean the exterior
Wipe gently with a soft cloth. Put the cloth in
diluted mild soap and wring it well to wipe off
heavy dirt. Then wipe again with a dry cloth.
To clean the LCD monitor
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
To clean the lens
Blow it with a blower brush, then wipe gently
with lens cleaning paper.
To clean the viewfinder lens
Remove dust from the viewfinder using a blower
brush.
NOTES:
● Avoid using strong cleaning agents such as
benzine or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units have
been disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth
refer to the cautions of each product.
● To clean the viewfinder, please consult your
nearest JVC dealer.
CAUTIONS
EN
51
...remove from charger or powered unit when not in
use, as some machines use current even when
switched off.
AC Adapter
WhenusingtheACAdapterinareasotherthan
the USA
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a
large power capacity. However, when one is
exposed to cold temperatures (below 10°C/
50°F), its usage time becomes shorter and it
may cease to function. If this happens, place
the battery pack in your pocket or other warm,
protected place for a short time, then re-
attach it to the camcorder.
The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an
AC wall outlet other than American National
StandardC73seriestypeuseanACplugadapter,
called a “Siemens Plug”, as shown.
ForthisACplugadapter,consultyournearestJVC
dealer.
NOTES:
Plug adapter
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging: 10°C to 35°C (50°F to 95°F)
Operation: 0°C to 40°C (32°F to 104°F)
Storage: –20°C to 50°C (–4°F to 122°F)
● The lower the temperature, the longer recharging
takes.
Battery Packs
The supplied battery
pack is a lithium-ion
battery. Before using the
Terminals
● Charging times are for a fully discharged battery
pack.
supplied battery pack or
an optional battery pack,
be sure to read the
following cautions:
● To avoid hazards
...do not burn.
...do not short-circuit the terminals. When
transporting, make sure the provided battery cap
is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
...do not modify or disassemble.
...do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
...use only specified chargers.
Cassettes
To properly use and store your cassettes, be
sure to read the following cautions:
● During use
...make sure the cassette bears the Mini DV mark.
...be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
...make sure the cassette is positioned properly
when inserting.
...do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
...do not open the front tape cover. This exposes
the tape to fingerprints and dust.
● To prevent damage and prolong service
life
● Store cassettes
...do not subject to unnecessary shock.
...charge in an environment where temperatures
are within the tolerances shown in the chart
below.This is a chemical reaction type battery —
cooler temperatures impede chemical reaction,
while warmer temperatures can prevent
complete charging.
...store in a cool, dry place. Extended exposure to
high temperatures will increase natural discharge
and shorten service life.
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
...vertically, in their original cases.
...fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
CAUTIONS
EN
52
...near a television set.
Memory Cards
To properly use and store your memory cards,
be sure to read the following cautions:
● During use
...make sure the memory card bears the SD or
MultiMediaCard mark.
...near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
...in places subject to extremely high (over 40°C or
104°F) or extremely low (under 0°C or 32°F)
temperatures.
...make sure the memory card is positioned
properly when inserting.
● While the memory card is being accessed
(during recording, playback, deletion,
initialization, etc.)
...never unload the memory card and never turn off
the camcorder.
● Store memory cards
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
● DO NOT leave the unit
...in places of over 50°C (122°F).
...in places where humidity is extremely low (below
35%) or extremely high (above 80%).
...in direct sunlight.
...in a closed car in summer.
...near a heater.
● To protect the unit, DO NOT
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during
transportation.
...keep the lens directed at extremely bright objects
for long periods.
...expose the lens and viewfinder’s lens to direct
sunlight.
...carry it by holding the LCD monitor or the
viewfinder.
...swing it excessively when using the hand strap or
the grip.
...swing the soft camera case excessively when the
camcorder is inside it.
● Dirty heads can cause the following
problems:
LCD Monitor
● To prevent damage to the LCD monitor, DO
NOT
...push it strongly or apply any shocks.
...place the camcorder with the LCD monitor on the
bottom.
● To prolong service life
...avoid rubbing it with coarse cloth.
● Be aware of the following phenomena for
LCD monitor use.These are not
malfunctions
...While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
...If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
...No picture during playback.
...Blocks of noise appear during playback.
...During recording or playback, the Head Clog
Warning indicator “ ” appears.
...Recording cannot be performed properly.
In such cases, use an optional cleaning
cassette. Insert it and play back. If the cassette
is used more than once consecutively, damage
to the video heads may result. After the
camcorder plays back for about 20 seconds, it
stops automatically. Also refer to the cleaning
cassette’s instructions.
Main Unit
● For safety, DO NOT
...open the camcorder’s chassis.
...disassemble or modify the unit.
...short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
...allow inflammables, water or metallic objects to
enter the unit.
If, after using the cleaning cassette, the
problems still exist, consult your nearest JVC
dealer.
...remove the battery pack or disconnect the power
supply while the power is on.
Mechanical moving parts used to move the
video heads and video tape tend to become
dirty and worn out over time. In order to maintain
a clear picture at all times, periodic check-ups
are recommended after using the unit for about
1,000 hours. For periodic check-ups please
consult your nearest JVC dealer.
...leave the battery pack attached when the
camcorder is not in use.
● Avoid using the unit
...in places subject to excessive humidity or dust.
...in places subject to soot or steam such as near a
cooking stove.
...in places subject to excessive shock or vibration.
CAUTIONS
EN
53
How To Handle A CD-ROM
Declaration of Conformity
Model Number
Trade Name
: GR-D390U
: JVC
● Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or back
surface. If the CD-ROM gets dirty, gently wipe it
with a soft cloth outward from the center hole.
● Do not use conventional disc cleaners or cleaning
spray.
● Do not bend the CD-ROM or touch its mirror
surface.
● Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
Responsible party : JVC AMERICAS
CORP.
Address
: 1700 Valley Road
Wayne, N. J. 07470
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
About moisture condensation
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form on
the glass’ outer surface. This same
Changes or modifications not approved by
JVC could void the user’s authority to operate
the equipment. This equipment has been
tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC
dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from
a TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery pack,
AC Adapter, etc.) and wait a few minutes and
then re-connect it and proceed as usual from
the beginning.
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
SPECIFICATIONS
EN
54
Maximum recording time (using 80 min.
cassette)
Camcorder
SP: 80 min., LP: 120 min.
For General
For Digital Still Camera
Power supply
DC 11 V (Using AC Adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 2.8 W (3.0 W*) (LCD monitor off, viewfinder
on)
Approx. 3.2 W (3.4 W*) (LCD monitor on, viewfinder
off)
Approx. 6.5 W (Maximum; when charging the
battery pack)
Storage media
SD Memory Card/MultiMediaCard
Compression system
JPEG (compatible)
File size
Still image:
1 mode (640 x 480 pixels)
Picture quality
2 modes (FINE/STANDARD)
Approximate number of storable images
੬ pg. 26
*
Using LED Light
Dimensions (W x H x D)
59 mm x 94 mm x 114 mm (2-5/16" x 3-11/16" x
4-1/2") (with the LCD monitor closed and the
For Connectors
viewfinder pushed back in)
Weight
Approx. 400 g (0.88 lbs) (without battery, cassette
and lens cap)
Approx. 480 g (1.06 lbs) (incl. battery, cassette and
lens cap)
Operating temperature
0°C to 40°C (32°F to 104°F)
AV
Video output: 1.0 V (p-p), 75 Ω, analog
Audio output: 300 mV (rms), 1 kΩ, analog, stereo
DV
Input/output: 4-pin, IEEE1394 compliant
USB
Mini USB-B type, USB 1.1 compliant
Operating humidity
35% to 80%
Storage temperature
–20°C to 50°C (–4°F to 122°F)
Pickup
1/6" CCD
AC Adapter
Power requirement
AC 110 V to 240 V~, 50 Hz/60 Hz
Output
DC 11 V =, 1 A
Lens
Specifications shown are for SP mode unless
otherwise indicated. E & O.E. Design and
specifications subject to change without notice.
F 2.0, f = 2.3 mm to 73.6 mm, 32:1 power zoom lens
Filter diameter
ø27 mm
LCD monitor
2.5" diagonally measured, LCD panel/TFT active
matrix system
Viewfinder
Electronic viewfinder with 0.33" color LCD
Speaker
Monaural
LED Light
Effective distance: 1.5 m (5 ft)
For Digital Video Camera
Format
DV format (SD mode)
Signal format
NTSC standard
Recording/Playback format
Video: Digital component recording
Audio: PCM digital recording, 32 kHz 4-channel
(12-BIT), 48 kHz 2-channel (16-BIT)
Cassette
Mini DV cassette
Tape speed
SP: 18.8 mm/s, LP: 12.5 mm/s
EN 55
A
AC Adapter .................................................... 15 Night-Alive .....................................................37
Audio Dubbing ............................................... 45
Playback Sound ............................................. 35
Backlight Compensation ................................ 39 Playback Special Effects ............................... 25
Battery Pack ...................................... 13, 14, 51 Power-Linked Operation ................................ 16
Blank Search ................................................. 22 Program AE, Effects and Shutter Effects ....... 41
B
C
Changing The Menu Settings ................ 31 – 35 Quick Review .................................................21
Connection To A Personal Computer ............ 44
Recording Capacity
Connections To A TV Or VCR ....................... 23
Data Battery ................................................... 14 Recording Media Selection ............................ 34
Date/Time Settings ........................................ 16 Remote Control ..............................................24
Deleting Files ................................................. 29 Resetting The File Name ............................... 28
D
Demonstration Mode ..................................... 34
Digital Image Stabilization (DIS) .................... 32
S
Speaker Volume ............................................ 21
Specifications .................................................54
DPOF Setting
(Digital Print Order Format) .................... 29
E
Exposure Control ........................................... 38 Spot Exposure Control ................................... 39
I
T
Initializing A Memory Card ............................. 30 Tape Speed (REC MODE) ...................... 32, 35
Insert Editing .................................................. 45 Tele Macro .....................................................32
Iris Lock ......................................................... 38 Time Code ........................................20, 34, 35
Tripod Mounting ............................................. 17
Troubleshooting ........................................46-49
L
LCD Monitor and Viewfinder .................... 19, 20
W
LED Light ....................................................... 36
Live Slow ....................................................... 36 Warning Indications ................................. 48, 49
Loading A Cassette ....................................... 18 White Balance ................................................39
Loading A Memory Card ................................ 18 Wide Mode .....................................................36
Wipe Or Fader Effects ................................... 40
M
Z
Manual Focus ................................................ 37
Memory Card ........................................... 18, 52 Zooming .............................................20, 24, 33
Motor Drive Mode .......................................... 37
EN
Printed in Malaysia
0206ASR-NF-VM
US
© 2006 Victor Company of Japan, Limited
|