JVC KS FX470 User Manual

CASSETTE RECEIVER  
KS-FX470  
RECEPTOR-REPRODUCTOR DE CASSETTE KS-FX470  
RADIOCASSETTE  
KS-FX470  
LOUD  
DISP  
Multi  
Music  
Scan  
SCAN  
7
8
9
10  
11  
12  
MO  
RM-RK31  
For installation and connections, refer to the separate manual.  
Para la instalación y las conexiones, refiérase al manual separado.  
Pour l’installation et les raccordements, se référer au manuel séparé.  
For customer Use:  
Enter below the Model No. and  
Serial No. which are located on  
the top or bottom of the cabinet.  
Retain this information for future  
reference.  
INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
MANUEL D’INSTRUCTIONS  
Model No.  
Serial No.  
GET0015-001A  
[J]  
OTHER MAIN FUNCTIONS.........................................19  
Setting the clock ............................................................................ 19  
Changing the general settings (PSM) ........................................ 20  
Basic Procedure ........................................................................ 20  
Canceling Advanced SCM ......................................................... 21  
Selecting the level display ......................................................... 21  
Selecting the dimmer mode ....................................................... 22  
Selecting the external component to use .................................. 22  
Detaching the control panel ......................................................... 23  
REMOTE OPERATIONS ..............................................24  
Installing the batteries.................................................................. 24  
Using the remote controller ......................................................... 25  
CD CHANGER OPERATIONS ......................................26  
Playing CDs ................................................................................... 26  
Selecting CD playback modes ..................................................... 28  
EXTERNAL COMPONENT OPERATIONS ......................29  
Playing an external component ................................................... 29  
MAINTENANCE ........................................................30  
To extend the lifetime of the unit ................................................. 30  
TROUBLESHOOTING .................................................31  
SPECIFICATIONS .......................................................32  
BEFORE USE  
* For safety....  
* Temperature inside the car....  
• Do not raise the volume level too much, as this If you have parked the car for a long time in hot  
will block outside sounds, making driving or cold weather, wait until the temperature in the  
dangerous.  
car becomes normal before operating the unit.  
• Stop the car before performing any complicated  
operations.  
3
BASIC OPERATIONS  
1
1
2
3
Note:  
When you use this unit for the  
first time, set the built-in clock  
correctly. (See page 19.)  
3
2
Turn on the power.  
“HELLO” appears on the display.  
Note on One-Touch Operation:  
When you select a source in step 2 below, the power automatically comes on.  
You do not have to press this button to turn on the power.  
Select the source.  
To operate the tuner, see pages 5 – 9.  
To operate the cassette deck, see pages 10 – 13.  
To operate the CD changer, see pages 26 – 28.  
To operate the external component, see page 29.  
Adjust the volume.  
Volume level appears  
Volume level indicator  
4
Adjust the sound as you want (see pages 14 – 18).  
To drop the volume in a moment  
Press  
briefly while listening to any source. “ATT” starts flashing on the display, and  
the volume level will drop in a moment.  
To resume the previous volume level, press the button briefly again.  
To turn off the power  
Press  
for more than 1 second.  
4
RADIO OPERATIONS  
Listening to the radio  
1
2
1
2
Select the band (FM1, FM2, FM3 or AM).  
You can select any one of FM1, FM2, and FM3 to listen to an  
FM station.  
F1  
F2  
F3  
AM  
(FM1) (FM2) (FM3)  
Audio (see page 21) or  
volume level indicator  
Selected band (or clock time:  
see page 19) appears  
To search stations of  
higher frequencies  
Start searching a station.  
While searching stations, "SEEK" appears  
on the display.  
To search stations of  
lower frequencies  
When a station is received, searching stops.  
To stop searching before a station is received, press the same button you have pressed  
for searching.  
To tune in a particular frequency without searching:  
1 Press FM/AM repeatedly to select the band (FM or AM).  
2 Press and hold ¢  
Now you can manually change the frequency while “MANU” is flashing.  
3 Press ¢ or 4 repeatedly until the frequency you want is reached.  
• If you hold down the button, the frequency keeps changing until you release the button.  
or 4  
until “MANU (Manual)” starts flashing on the display.  
5
Storing stations in memory  
You can use one of the following two methods to store broadcasting stations in memory.  
• Automatic preset of FM stations: SSM (Strong-station Sequential Memory)  
• Manual preset of both FM and AM stations  
FM station automatic preset: SSM  
You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).  
1
2
1
2
Select the FM band number (FM1, FM2 or  
FM3) you want to store FM stations into.  
F1  
(FM1)  
F2  
(FM2) (FM3)  
F3  
AM  
Press and hold both buttons for more than  
2 seconds.  
“SSM” appears, then disappears when  
automatic preset is over.  
Local FM stations with the strongest signals are searched and stored automatically in the  
band number you have selected (FM1, FM2 or FM3). These stations are preset in the number  
buttons — No. 1 (lowest frequency) to No. 6 (highest frequency).  
When automatic preset is over, the station stored in number button 1 will be automatically  
tuned in.  
6
Manual preset  
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.  
EXAMPLE: Storing an FM station of 88.3 MHz into the preset channel number 1 of the FM1 band  
3
1
2
1
2
Select the FM1 band.  
Tune into a station of 88.3 MHz.  
See page 5 to tune into a station.  
3
Press and hold the number button (in this  
example, 1) for more than 2 seconds.  
Selected band,preset number and  
“MEMO” flash alternately for a while.  
4 Repeat the above procedure to store other stations into other  
preset channel numbers.  
Notes:  
• A previously preset station is erased when a new station is stored in the same preset channel number.  
• Preset stations are erased when the power supply to the memory circuit is interrupted (for example,  
during battery replacement). If this occurs, preset the stations again.  
7
Tuning into a preset station  
You can easily tune into a preset station.  
Remember that you must store stations first. If you have not stored them yet, see pages 6  
and 7.  
2
1
1
2
Select the band (FM1, FM2, FM3 or AM)  
you want.  
F1  
F2  
F3  
AM  
(FM1) (FM2) (FM3)  
Select the number (1 – 6) for the preset station  
you want.  
8
Other convenient tuner functions  
MO RND  
SCAN  
Scanning broadcast stations  
When you press SCAN while listening to the radio, station scanning starts. Each time a  
broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes  
on display), and you can check what program is now being broadcasted.  
If you want to listen to that program, press the same button again to stop scanning.  
Selecting FM reception sound  
When an FM stereo broadcast is hard to receive:  
Press MO RND (Monaural/Random) while listening to an FM stereo broadcast. The MONO  
indicator lights up on the display. The sound you hear becomes monaural but reception will  
be improved.  
Lights up when receiving an FM broadcast in stereo.  
To restore the stereo effect, press the same button again.  
9
TAPE OPERATIONS  
Listening to a tape  
1
RPT  
3
1
2
Open the control panel.  
1. Insert a cassette into the cassette  
compartment.  
The unit turns on and tape play starts automatically.  
2. Close the control panel by hand.  
• When one side of the tape reaches its end during play, the other side of the tape  
automatically starts playing. (Auto Reverse)  
Note on One-Touch Operation:  
When a cassette is already in the cassette compartment, pressing TAPE 2 3 turns on the  
unit and starts tape play automatically.  
3
Select the tape direction.  
Each time you press the button, the tape direction changes  
alternately – forward (  
) and reverse (  
).  
To play back tapes recorded with the Dolby B NR  
Press  
The  
RPT (Dolby NR/Repeat) for more than 2 seconds to set the Dolby B NR* system.  
indicator lights up, and “DOLBY B” appears on the display for several seconds.  
To cancel the Dolby B NR, press the same button again.  
* Dolby noise reduction manufactured under license from Dolby Laboratories Licensing  
Corporation.  
“DOLBY” and the double-D symbol  
Corporation.  
are trademarks of Dolby Laboratories Licensing  
10  
To stop play and eject the cassette  
Press 0.  
Tape play stops, the control panel opens, then the cassette automatically ejects from the  
cassette compartment.  
If you change the source to FM, AM or CD changer, the tape play also stops (without ejecting  
the cassette this time).  
• You can also eject the cassette with the unit turned off.  
To fast-forward and rewind a tape  
• Press ¢  
for more than 1 second to fast-forward the tape.  
When the tape reaches its end, the tape is reversed and playback  
starts from the beginning of the other side.  
• Press 4  
for more than 1 second to rewind the tape.  
When the tape reaches its end, playback of the same side starts.  
To stop fast forward and rewind at any position on the tape, press TAPE 2 3 .  
Tape play starts from that position on the tape.  
11  
Finding the beginning of a tune  
Multi Music Scan allows you to automatically start playback from the beginning of a specified  
tune. You can specify up to 9 tunes ahead of or before the current tune.  
¢
4
During playback  
To locate a tune ahead  
of the current tune on  
the tape  
Specify where (how many tunes  
ahead of or before the current tune)  
To locate a tune before  
the current tune on the  
tape  
the tune you want is located.  
Each time you set the tune, the number changes  
up to 9.  
When the beginning of the specified tune is located, playback starts automatically.  
Notes:  
• While locating a specified tune:  
– If the tape is rewound to its beginning, playback starts from the beginning of that side.  
– If the tape is fast-forwarded to the end, it is reversed and played from the beginning of the other  
side.  
• In the following cases, the Multi Music Scan function may not operate correctly:  
– Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions  
between tunes.  
– Tapes with short non-recorded sections.  
– Tapes with high level of noise or humming between tunes.  
– The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded  
with no Dolby NR.  
12  
Other convenient tape functions  
Skipping the blank portions on the tape  
You can skip blank portions between the tunes. (Blank Skip)  
When this function is on, the unit skips blank portions of 15 seconds or more, fast-forwards to  
the next tunes, then starts playing it.  
• See also “Changing the general settings (PSM)” on page 20.  
1. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears  
on the display.  
2. Select “B SKIP (Blank Skip)” with ¢  
3. Select the desired mode with the control dial.  
The Blank Skip mode alternates between on and off.  
or 4  
.
ON  
OFF  
Note:  
When the tape reaches its end while fast-forwarding, the tape direction will be changed automatically.  
Playing the current tune repeatedly  
You can play the current tune repeatedly. (Repeat Play)  
Each time you briefly press  
RPT (Dolby NR/Repeat) while playing a  
tape, Repeat Play turns on and off alternately.  
Lights up when Repeat Play is turned on.  
Notes:  
• In the following cases, Blank Skip and Repeat Play may not operate correctly:  
Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during  
tunes.  
– Tapes with short non-recorded sections.  
– Tapes with high level noise or humming between tunes.  
– The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with  
no Dolby NR.  
Prohibiting cassette ejection  
You can prohibit the cassette ejection and can “lock” a cassette in the cassette compartment.  
Press and hold TAPE 2 3 and  
for more than 2 seconds. NO EJECTflashes on  
the display for about 5 seconds, and the cassette is locked.”  
To cancel the prohibition and “unlock” the cassette, press and hold TAPE 2 3 and  
for more than 2 seconds again. EJECT OKflashes for about 5 seconds, and this  
time the cassette is unlocked.”  
13  
SOUND ADJUSTMENTS  
Adjusting the sound  
You can adjust the treble/bass sound and the speaker balance.  
2
Equalization pattern indicator  
1
1
Select the item you want to adjust.  
Indication  
To do:  
Adjust the bass  
Range  
BAS  
–06 (min.) — +06 (max.)  
(Bass)  
TRE  
Adjust the treble  
–06 (min.) — +06 (max.)  
(Treble)  
FAD  
(Fader)*  
Adjust the front and rear speaker  
balance  
R06 (rear only) — F06 (front only)  
L06 (left only) — R06 (right only)  
00 (min.) — 50 (max.)  
BAL  
Adjust the left and right speaker  
(Balance) balance  
VOL  
Adjust the volume  
(Volume)  
Note:  
* If you are using a two-speaker system, set the fader level to “00.”  
2
Adjust the level.  
Equalization pattern changes as you  
adjust the bass or treble.  
Note:  
Normally the control dial works for volume adjustment. So you do  
not have to select “VOL” to adjust the volume level.  
14  
Turning on/off the loudness function  
The human ear is less sensitive to low and high frequencies at low volumes.  
The loudness function can boost these frequencies to produce well-balanced sound at low  
volume level.  
1
1
Turn on or off the loudness function.  
Each time you press LOUD, the loudness function turns on and off  
alternately.  
15  
Using the Sound Control Memory  
You can select and store a preset sound adjustment suitable to each playback source.  
(Advanced SCM)  
Selecting and storing the sound modes  
Once you select a sound mode, it is stored in memory, and will be recalled every time you  
select the same source. A sound mode can be stored each of the following sources — FM1,  
FM2, FM3, AM, tape, CD-changer and external components.  
• If you do not want to store the sound mode separately for each playback source, but  
want to use the same sound mode for all the sources, see “Canceling Advanced SCM”  
on page 21.  
“SCM” indicator  
SCM  
Select the sound mode you want.  
Each time you press the button, the sound mode changes as follows:  
• When “SCM LINK” is set to “LINK ON”, the selected sound mode can  
be stored in memory for the current source and the effect applies only  
to the current source. Each time you change the playback source, the  
SCM indicator flashes on the display.  
• When “SCM LINK” is set to “LINK OFF”, the selected sound mode  
effect applies to any source.  
Indication  
For:  
Preset values  
Bass  
00  
Treble  
00  
Loudness  
SCM OFF  
BEAT  
(Flat sound)  
On  
On  
Off  
Off  
Rock or disco music  
Quiet background music  
Light music  
+02  
+01  
+04  
00  
SOFT  
–03  
+01  
POP  
16  
Recalling the sound modes  
1
1
Select the source while the “SCM” indicator is  
lit on the display.  
The “SCM” indicator starts flashing, and the sound mode  
stored in memory for the selected source is recalled.  
Sound mode  
indicator  
Equalization pattern of the  
selected sound mode appears.  
Notes:  
• You can adjust each sound mode to your preference, and store it in memory.  
If you want to adjust and store your original sound mode, see “Storing your own sound adjustments”  
on page 18.  
• To adjust the bass and treble reinforcement levels or to turn on/off the loudness function temporarily,  
see pages 14 and 15. (Your adjustments will be canceled if another source is selected.)  
17  
Storing your own sound adjustments  
You can adjust the sound modes (BEAT, SOFT, POP: see page 16) to your preference and  
store your own adjustments in memory.  
3
2 2  
1,4  
1
2
Call up the sound mode you want to adjust.  
See page 16 for details.  
Within  
5 seconds  
To adjust the bass or treble sound level  
Select “BAS” or “TRE.”  
To turn on or off the loudness function  
See page 15 for details.  
Within  
5 seconds  
3
Adjust the bass or treble level.  
See page 14 for details.  
Within  
5 seconds  
4
5
Press and hold SCM (Sound Control Memory)  
until the sound mode you have selected  
flashes on the display.  
Your setting is stored in memory.  
Repeat the same procedure to store other settings.  
To reset to the factory settings  
Repeat the same procedure and reassign the preset values listed in the table on page 16.  
18  
OTHER MAIN FUNCTIONS  
Setting the clock  
2,3  
DISP  
1,4  
2,3  
1
2
Press and hold SEL (Select) for more than 2 seconds  
so that one of the PSM items appears on the display.  
2
1
1
Set the hour.  
1 Select “CLOCK H (Hour)” if not  
shown on the display.  
2 Adjust the hour.  
2
3
4
Set the minute.  
1 Select “CLOCK M (Minute).”  
2 Adjust the minute.  
Finish the setting.  
To check the current clock time (changing the display mode)  
Press DISP repeatedly. Each time you press the button, the display mode changes as follows:  
During tuner operation:  
During tape operation:  
Clock  
TAPE  
Clock  
Band  
During CD changer operation:  
During external component operation:  
Clock appears and disappears alternately.  
Disc number  
Clock  
• If the unit is not in use when you press DISP, the power turns on, the clock time is shown for  
5 seconds, then the power turns off.  
19  
Changing the general settings (PSM)  
You can change the items listed on the next page by using the PSM (Preferred Setting Mode)  
control.  
Basic Procedure  
3
1,4  
2
1
Press and hold SEL (Select) for more than 2  
seconds so that one of the PSM items  
appears on the display.  
2
3
Select the PSM item you want to adjust. (See  
page 21.)  
Select or adjust the PSM item selected above.  
4
Finish the setting.  
20  
1
2
3
Factory-preset  
settings  
See  
page  
Select.  
Set.  
Advance  
CLOCK H  
CLOCK M  
SCM LINK  
Hour adjustment  
Minute adjustment  
Back  
Back  
1:00  
19  
Advance  
Sound control  
memory linkage  
LINK OFF  
AUDIO 1  
LINK ON  
LINK ON  
below  
LEVEL  
Level display  
Dimmer  
AUDIO 2  
OFF  
AUDIO 2  
AUTO  
below  
22  
OFF  
ON  
DIMMER  
AUTO  
B. SKIP  
EXT IN*  
Blank skip  
OFF  
ON  
OFF  
13  
22  
External component  
CHANGER  
LINE IN  
CHANGER  
* Displayed only when one of the following sources is selected — FM, AM and tape.  
• Press SEL (select) when the setting is complete.  
Canceling Advanced SCM  
You can cancel the Advanced SCM (Sound Control Memory), and unlink the sound modes  
and the playback sources.  
When shipped from the factory, a different sound mode can be stored in memory for each  
source so that you can change the sound modes simply by changing the sources.  
• LINK ON:  
• LINK OFF:  
Advanced SCM (different sound modes for different sources)  
Conventional SCM (one sound mode for all sources)  
1. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears  
on the display.  
2. Select “SCM LINK” with ¢  
or 4  
.
3. Select the desired mode with the control dial.  
The SCM LINK mode changes as follows:  
LINK ON  
LINK OFF  
Selecting the level display  
You can select the level display according to your preference.  
When shipped from the factory, “AUDIO 2” is selected.  
• AUDIO 1: Shows the audio level indicator and the equalization pattern indicator.  
• AUDIO 2: Alternates “AUDIO 1” setting and illumination display.  
• OFF:  
Erases the audio level indicator and the equalization pattern indicator.  
1. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears  
on the display.  
2. Select “LEVEL” with ¢  
or 4  
.
3. Select the desired mode with the control dial.  
The level display setting changes as follows:  
AUDIO 1  
AUDIO 2  
OFF  
21  
Selecting the dimmer mode  
When you turn on the car head lights, the display automatically dims (Auto Dimmer).  
When shipped from the factory, Auto Dimmer mode is activated.  
• AUTO:  
• ON:  
• OFF:  
Activates Auto Dimmer.  
Always dims the display.  
Cancels Auto Dimmer.  
1. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears  
on the display.  
2. Select “DIMMER” with ¢  
or 4  
.
3. Select the desired mode with the control dial.  
The dimmer mode changes as follows:  
AUTO  
OFF  
ON  
Note on Auto Dimmer:  
Auto Dimmer equipped with this unit may not work correctly on some vehicles, particularly on those  
having a control dial for dimming.  
In this case, set the dimmer mode to “ON” or “OFF”.  
Selecting the external component to use  
You can connect the external component to the CD changer jack on the rear using the Line  
Input Adaptor KS-U57 (not supplied).  
To use the external component as the playback source through this unit, you need to select  
which component — CD changer or external component — to use. When shipped from the  
factory, CD changer is selected as the external component.  
• LINE IN:  
• CHANGER:  
To use the external component other than CD changer.  
To use the CD changer.  
1. Change the source to FM, AM or tape with FM/AM or TAPE 2 3 .  
2. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears  
on the display.  
3. Select “EXT IN” with ¢  
or 4  
.
4. Select the desired mode with the control dial.  
The external component selecting mode changes as follows:  
LINE IN  
CHANGER  
Note:  
For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/  
Connection Manual (separate volume).  
22  
Detaching the control panel  
You can detach the control panel when leaving the car.  
When detaching or attaching the control panel, be careful not to damage the connectors on  
the back of the control panel and on the panel holder.  
How to detach the control  
panel  
How to attach the control  
panel  
Before detaching the control panel, be sure  
to turn off the power.  
1
Insert the right side of the  
control panel into the groove  
on the panel holder.  
1
Unlock the control panel.  
2
2
Press the left side of the  
control panel to fix it to the  
panel holder.  
Pull the control panel out of  
the unit.  
3
Put the detached control  
panel into the provided case.  
Note on cleaning the connectors:  
If you frequently detach the control panel, the  
connectors will deteriorate.  
To minimize this possibility, periodically wipe  
the connectors with a cotton swab or cloth  
moistened with alcohol, being careful not to  
damage the connectors.  
Connectors  
23  
REMOTE OPERATIONS  
Remote sensor  
Before using the remote controller:  
• Aim the remote controller directly at the remote sensor  
on the main unit. Make sure there is no obstacle in  
between.  
• Do not expose the remote sensor to strong light (direct  
sunlight or artificial lighting).  
Installing the battery  
When the controllable range or effectiveness of the remote controller decreases, replace  
the battery.  
1. Remove the battery holder.  
1) Push out in the direction indicated by the arrow  
using a ball point pen or a similar tool.  
2) Remove the battery holder.  
(back side)  
1)  
2)  
Lithium coin battery  
(product number:  
CR2025)  
2. Place the battery.  
Slide the battery into the holder with the + side facing  
upwards so that the battery is fixed in the holder.  
3. Return the battery holder.  
Insert again the battery holder pushing it until you hear  
a clicking sound.  
(back side)  
WARNING:  
• Store the batteries in a place which children cannot reach.  
If a child accidentally swallows the battery, immediately consult a doctor.  
• Do not recharge, short, disassemble or heat the batteries or dispose of in a fire.  
Doing any of these things may cause the batteries to give off heat, crack or start a fire.  
• Do not leave the batteries with other metallic materials.  
Doing this may cause the batteries to give off heat, crack or start a fire.  
• When throwing away or saving the batteries, wrap in tape and insulate; otherwise, , it may cause  
the batteries to give off heat, crack or start a fire.  
• Do not poke the batteries with tweezers or similar tools.  
Doing this may cause the batteries to give off heat, crack or start a fire.  
24  
Using the remote controller  
1 Functions the same as the  
button on the main unit.  
2 Functions as the BAND button while listening to the radio.  
Each time you press the button, the band changes.  
Functions as the DISC + button while listening to the CD  
changer.  
5
6
1
2
3
4
7
Each time you press the button, the disc number increases,  
and the selected disc starts playing.  
Functions as the PROG button while listening to a tape  
Each time you press the button, the tape direction changes  
alternately.  
3 Functions as the PRESET button while listening to the  
radio.  
Each time you press the button, the preset station number  
increases, and the selected station is tuned in.  
Functions as the DISC button while listening to the CD  
changer.  
RM-RK31  
Each time you press the button, the disc number decreases,  
and the selected disc starts playing.  
4 Functions the same as the control dial on the main unit.  
Note: This button does not function for the preferred settings  
mode adjustment.  
5 Selects the sound mode.  
Each time you press SCM (Sound Control Memory), the mode  
changes.  
6 Selects the source.  
Each time you press FUNC (Function), the source changes.  
7 Searches stations while listening to the radio.  
Fast forwards or reverses the track if pressed and held  
while listening to a CD.  
Skips to the beginning of the next tracks or goes back to  
the beginning of the current (or previous tracks) if pressed  
briefly while listening to a CD.  
Functions as the fast forward or rewind buttons or Multi  
Music Scan buttons while listening to a tape.  
25  
CD CHANGER OPERATIONS  
We recommend that you use one of the CH-X series with your unit.  
If you have another CD automatic changer, consult your JVC car audio dealer for connections.  
For example, if your CD automatic changer is one of the KD-MK series, you need a cord (KS-U15K)  
for connecting it to this unit.  
Before operating your CD automatic changer:  
• Refer also to the Instructions supplied with your CD changer.  
• If no discs are in the magazine of the CD changer or the discs are inserted upside  
down, “NO DISC” will appear on the display. If this happens, remove the magazine and  
set the discs correctly.  
• If “RESET 1 - RESET 8” appears on the display, something is wrong with the connection  
between this unit and the CD changer. If this happens, check the connection, connect  
the connecting cord(s) firmly if necessary, then press the reset button of the CD changer.  
Playing CDs  
¢
CD-CH  
Number buttons  
4
Select the CD automatic changer.  
Playback starts from the first track of the first disc.  
All tracks of all discs are played back.  
Elapsed playing time  
Track number  
Disc number (or clock time: see page 19) appears.  
Note on One-Touch Operation:  
When you press CD-CH, the power automatically comes on. You do not have to press  
to turn on the power.  
26  
To fast-forward or reverse the track  
Press and hold ¢  
, while playing a CD, to fast-forward the track.  
Press and hold 4  
, while playing a CD, to reverse the track.  
To go to the next tracks or the previous tracks  
Press ¢  
briefly, while playing a CD, to go ahead to the beginning of  
the next track.  
Each time you press the button consecutively, the beginning of the next  
tracks is located and played back.  
Press 4  
briefly, while playing a CD, to go back to the beginning of  
the current track.  
Each time you press the button consecutively, the beginning of the previous  
tracks is located and played back.  
To go to a particular disc directly  
Press the number button corresponding to the disc number to start its  
playback (while the CD changer is playing).  
To select a disc number from 1 6:  
Press 1 (7) 6 (12) briefly.  
To select a disc number from 7 12:  
Press and hold 1 (7) 6 (12) for more than 1 second.  
Ex. When disc number 3 is selected  
Track number  
Disc number  
27  
Selecting CD playback modes  
RPT MO RND  
To play back tracks at random (Random Play)  
Each time you press MO RND (Monaural/Random) while playing a CD, CD  
random play mode changes as follows:  
MO  
RND1  
RND2  
(Random2)  
(Random1)  
Canceled  
Mode  
RND Indicator  
Plays at random  
RND1  
Lights  
All tracks of the current disc, then the tracks of the  
next disc, and so on.  
RND2  
Flashes  
All tracks of all discs inserted in the magazine.  
To play back tracks repeatedly (Repeat Play)  
Each time you press  
RPT (Dolby NR/Repeat) while playing a CD, CD  
repeat play mode changes as follows:  
RPT1  
RPT2  
(Repeat2)  
(Repeat1)  
Canceled  
Mode  
RPT1  
RPT2  
RPT Indicator  
Plays repeatedly  
Lights  
The current track (or specified track).  
Flashes  
All tracks of the current disc (or specified disc).  
28  
EXTERNAL COMPONENT OPERATIONS  
Playing an external component  
You can connect the external component to the CD changer jack on the rear using the Line  
Input Adaptor KS-U57 (not supplied).  
3
1
Preparations:  
For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/  
Connection Manual (separate volume).  
Before operating the external component using the following procedure, select the external input  
correctly. (See “Selecting the external component to use” on page 22.)  
1
Select the external component.  
• If “LINE IN”* does not appear on the display, see page 22  
and select the external input (“EXT IN”).  
*Displayed only when one of the following sources is selected  
— FM, AM and tape.  
Note on One-Touch Operation:  
When you press CD-CH, the power automatically comes on. You do not have to press  
to turn on the power.  
2
Turn on the connected component and start playing the source.  
3
Adjust the volume.  
29  
MAINTENANCE  
To extend the lifetime of the unit  
This unit requires very little attention, but you will be able to extend the life of the unit if you  
follow the instructions below.  
To clean the heads  
• Clean the heads after every 10 hours of use using a wet-  
type head cleaning tape (available at an audio store).  
When the head becomes dirty, you may realize the following  
symptoms:  
– Sound quality is reduced.  
– Sound level decreases.  
– Sound drops out.  
• Do not play dirty or dusty tapes.  
• Do not touch the highly-polished head with any metallic or  
magnetic tools.  
To keep the tape clean  
• Always store the tapes to their storage cases after use.  
• Do not store tapes in the following places:  
– Subject to direct sunlight  
– With high humidity  
– At extremely hot temperatures  
CAUTIONS:  
• Do not play the tapes with peeling labels; otherwise, they can damage the unit.  
• Tighten tapes to remove slack since loose tape may become entangled with the mechanism.  
• Do not leave a cassette in the cassette compartment after use, as the tape may become slack.  
The function below is also provided to ensure the longer life of this unit.  
Ignition key-off Release/Ignition key-on play  
• When you turn off the ignition key with a cassette in the compartment, the unit automatically  
releases the tape from its head.  
• When you turn on the ignition key with a cassette in the compartment, playback automatically  
starts.  
30  
TROUBLESHOOTING  
What appears to be trouble is not always serious. Check the following points before calling a  
service center.  
Symptoms  
Causes  
Remedies  
• A cassette tape cannot be  
inserted.  
You have tried to insert a  
cassette in the wrong way.  
Insert the cassette with the  
exposed tape facing right.  
• Cassette tapes become hot. This is not a malfunction.  
Tape sound is at very low  
level and sound quality is  
degraded.  
The tape head is dirty.  
Clean it with a head cleaning  
tape.  
• Sound is sometimes  
interrupted.  
Connections are not good.  
Check the cords and  
connections.  
• Sound cannot be heard from The volume is turned to the  
Adjust it to the optimum level.  
the speakers.  
minimum level.  
Connections are incorrect.  
Check the cords and  
connections.  
• SSM (Strong-station  
Sequential Memory)  
automatic preset does not  
work.  
Signals are too weak.  
Store stations manually.  
• Static noise while listening  
to the radio.  
The antenna is not connected  
firmly.  
Connect the antenna firmly.  
• “NO DISC” appears on the  
display.  
No CD is in the magazine.  
CDs are inserted incorrectly.  
Insert CDs into the magazine.  
Insert them correctly.  
• “RESET 8” appears on the  
display.  
This unit is not connected to a  
CD changer correctly.  
Connect this unit and the CD  
changer correctly and press  
the reset button of the CD  
changer.  
• “RESET 1 - RESET 7”  
appears on the display.  
Press the reset button of the  
CD changer.  
• This unit does not work at  
all.  
• The CD changer does not  
work at all.  
The built-in microcomputer  
may function incorrectly due to  
noise, etc.  
Press the reset button on the  
panel (The clock setting and  
preset stations stored in  
memory are erased.) (See  
page 2.)  
31  
SPECIFICATIONS  
AUDIO AMPLIFIER SECTION  
CASSETTE DECK SECTION  
Maximum Power Output:  
Wow & Flutter: 0.11% (WRMS)  
Front: 45 W per channel  
Rear: 45 W per channel  
Continuous Power Output (RMS):  
Fast-Wind Time: 100 sec. (C-60)  
Frequency Response (Dolby NR-OFF):  
30 Hz to 16 000 Hz (Normal tape)  
Front: 17 W per channel into 4 , 40Hz Signal-to-Noise Ratio: (Normal tape)  
to 20 000 Hz at no more than 0.8%  
total harmonic distortion.  
(Dolby NR-ON): 65 dB  
(Dolby NR-OFF): 56 dB  
Rear: 17 W per channel into 4 , 40Hz Stereo Separation: 40 dB  
to 20 000 Hz at no more than 0.8%  
total harmonic distortion.  
Load Impedance: 4 (4 to 8 allowance)  
Tone Control Range  
Bass: 10 dB at 100 Hz  
Treble: 10 dB at 10 kHz  
Frequency Response: 40 Hz to 20 000 Hz  
Signal-to-Noise Ratio: 70 dB  
Line-Out Level/Impedance:  
GENERAL  
Power Requirement  
Operating Voltage: DC 14.4 V (11 V to 16 V  
allowance)  
Allowable Working Temperature:  
0°C to +40°C (32°F to 104°F)  
Grounding System: Negative ground  
Dimensions (W x H x D)  
2.0 V/20 kload (250 nWb/m)  
Installation Size:  
182 mm x 52 mm x 150 mm  
(7-3/16" x 2-1/16" x 5-15/16")  
Panel Size: 188 mm x 58 mm x 14 mm  
(7-7/16" x 2-5/16" x 5/8")  
TUNER SECTION  
Frequency Range  
FM: 87.5 MHz to 107.9 MHz  
AM: 530 kHz to 1 710 kHz  
Mass: 1.3 kg (2.9 lbs) (excluding accessories)  
Design and specifications subject to change  
without notice.  
[FM Tuner]  
Usable Sensitivity: 11.3 dBf (1.0 µV/75 )  
50 dB Quieting Sensitivity:  
16.3 dBf (1.8 µV/75 )  
Alternate Channel Selectivity (400 kHz):  
65 dB  
Frequency Response: 40 Hz to 15 000 Hz  
Stereo Separation: 35 dB  
Capture Ratio: 1.5 dB  
If a kit is necessary for your car, consult  
your telephone directory for the nearest  
car audio speciality shop.  
[AM Tuner]  
Sensitivity: 20 µV  
Selectivity: 35 dB  
32  
.jvcmobile.com  
Visit us on-line for  
Technical Support & Customer Satisfaction Survey.  
US RESIDENTS ONLY  
Having TROUBLE with operation?  
Please reset your unit  
Refer to page of How to Reset  
Still having trouble??  
USA ONLY  
Call 1-800-252-5722  
We can help you!  
VICTOR COMPANY OF JAPAN, LIMITED  
EN, SP, FR  
1000HISFLEJES  
J
C
V
KS-FX470  
Installation/Connection Manual  
Manual de instalación/conexión  
Manuel d’installation/raccordement  
1000HISFLEJES  
EN, SP, FR  
J
C
V
GET0015-002A  
[J]  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
This unit is designed to operate on 12 volts DC, NEGATIVE Esta unidad está diseñada para funcionar con 12 voltios de Cet appareil est conçu pour fonctionner sur des sources de  
ground electrical systems.  
CC, con sistemas eléctricos de masa NEGATIVA.  
courant continu de 12 volts à masse NEGATIVE.  
INSTALLATION (IN-DASH  
MOUNTING)  
INSTALACION (MONTAJE EN EL  
TABLERO DE INSTRUMENTOS)  
INSTALLATION (MONTAGE DANS LE  
TABLEAU DE BORD)  
The following illustration shows a typical installation. However, La siguiente ilustración muestra una instalación típica. Sin L’illustration suivante est un exemple d’installation typique.  
you should make adjustments corresponding to your specific  
car. If you have any questions or require information regarding  
installation kits, consult your JVC car audio dealer or a company  
supplying kits.  
embargo usted deberá efectuar los ajustes correspondientes  
a su automóvil. Si tiene alguna pregunta o necesita información  
acerca de las herramientas para instalación, consulte con su  
concesionario de JVC de equipos de audio para automóviles o  
a una compañía que suministra tales herramientas.  
Cependant, vous devez faire les ajustements correspondant à  
votre voiture particulière. Si vous avez des questions ou avez  
besoin d’information sur des kits d’installation, consulter votre  
revendeur d’autoradios JVC ou une compagnie  
d’approvisionnement.  
1 Before mounting: Press  
(Control Panel Release) to  
1 Antes de instalar: Pulse  
(soltar panel de control) para  
1 Avant le montage: Appuyez sur  
(déblocage du  
detach the control panel if already attached.  
separar el panel de control si ya está unido.  
panneau de commande) pour éventuellement détacher le  
panneau de commande.  
* When shipped from the factory, the control panel is packed  
in the hard case.  
* Cuando se envía de la fábrica, el panel de control está  
embalado en el estuche duro.  
* Lorsque ce panneau de commande sort d'usine, il est  
rangé dans un étui de transport.  
2 Remove the trim plate.  
3 Remove the sleeve after disengaging the sleeve locks.  
1 Stand the unit.  
2 Retire la placa de guarnición.  
2 Retirer la plaque dassemblage.  
3 Libérer les verrous du manchon et retirer le manchon.  
1 Poser lappareil à la verticale.  
3 Retire la cubierta después de desenganchar los retenes  
de la cubierta.  
1 Ponga la unidad vertical.  
Note: When you stand the unit, be careful not to damage  
the fuse on the rear.  
Nota: Al poner la unidad vertical, tenga cuidado de no  
dañar el fusible provisto en la parte posterior.  
2 Inserte las dos asas entre la unidad y la cubierta tal  
como en la ilustración y desenganche los retenes de la  
cubierta.  
Remarque: Lorsque vous mettez lappareil à la verticale,  
faire attention de ne pas endommager le fusible situé  
sur le fond.  
2 Insert the 2 handles between the unit and the sleeve, as  
illustrated, to disengage the sleeve locks.  
3 Remove the sleeve.  
2 Insérer les 2 poignées entre lappareil et le manchon  
comme indiqué pour désengagé les verrous de manchon.  
Note: Be sure to keep the handles for future use after  
installing the unit.  
3 Retire la cubierta.  
3 Retirer le manchon.  
Nota: Después de instalar la unidad, asegúrese de  
guardar las asas para uso futuro.  
4 Install the sleeve into the dashboard.  
Remarque: S'assurer de garder les poignées pour une  
utilisation ultérieur, après l'installation de l'appareil.  
4 Instale la cubierta en el tablero de instrumentos.  
* After the sleeve is correctly installed in the dashboard,  
bend the appropriate tabs to hold the sleeve firmly in place,  
as illustrated.  
4 Installer le manchon dans le tableau de bord.  
* Después de que la cubierta esté correctamente instalada  
en el tablero de instrumentos, doble las lengüetas  
correspondientes para sostener la cubierta firmemente  
en su lugar, tal como se muestra.  
* Après installation correcte du manchon dans le tableau  
de bord, plier les bonnes pattes pour maintenir fermement  
le manchon en place, comme montré.  
5 Fix the mounting bolt to the rear of the unit’s body and place  
the rubber cushion over the end of the bolt.  
5 Fije el perno de montaje en la parte trasera del cuerpo de  
la unidad y coloque el cojín de goma sobre el extremo del  
perno.  
6 Do the required electrical connections explained on the back  
5 Monter le boulon de montage sur larrière du corps de  
lappareil puis passer lamortisseur en caoutchouc sur  
lextrémité du boulon.  
of this instructions.  
7 Slide the unit into the sleeve until it is locked.  
6 Realice las conexiones eléctricas requeridas en base a  
las explicaciones que figuran en la parte de atrás de estas  
instrucciones.  
6 Réalisez les connexions électriques expliquées au dos de  
8 Attach the trim plate so that the projection on the trim plate  
cette page.  
is fixed to the left side of the unit.  
7 Faites glisser lappareil dans le manchon jusqu’à ce quil  
9 Attach the control panel.  
7 Deslice la unidad dentro de la cubierta hasta que se  
soit verrouillé.  
bloquee.  
8 Attachez la plaque dajustage de façon que la projection de  
8 Coloque la placa de guarnición de manera que el saliente  
de la misma quede colocado en el lateral izquierdo de la  
unidad.  
9 Coloque el panel de control.  
la plaque soit fixée sur le cote gauche de lappareil.  
9 Remonter le panneau de commande.  
Dashboard  
Tablero de instrumentos  
Tableau de bord  
1
3
2
Rubber cushion  
Cojín de goma  
Amortisseur en caoutchouc  
184 mm  
Sleeve  
53 mm  
4
Cubierta  
Manchon  
5
7
Mounting bolt  
Handle  
Manija  
Poignée  
Perno de montaje  
Boulon de montage  
Lock Plate  
Placa de bloqueo  
Plaque de verrouillage  
8
*
4
6
See “ELECTRICAL CONNECTIONS.”  
Consulte “CONEXIONES  
ELECTRICAS.”  
Référez-vous “RACCORDEMENTS  
ELECTRIQUES.”  
Slot  
Ranura  
Fente  
9
Fuse  
Fusible  
Fusible  
1
0
Sleeve  
Cubierta  
Manchon  
Trim plate  
Placa de guarnición  
Plaque d’assemblage  
TROUBLESHOOTING  
LOCALIZACION DE AVERIAS  
EN CAS DE DIFFICULTÉS  
The fuse blows.  
• El fusible se quema.  
• Le fusible saute.  
* Are the red and black leads connected correctly?  
* ¿Están los conductores rojo y negro correctamente conectados? * Les fils rouge et noir sont-ils racordés correctement?  
Power cannot be turned on.  
* Is the yellow lead connected?  
• No es posible conectar la alimentación.  
* ¿Está el cable amarillo conectado?  
• L’appareil ne peut pas être mise sous tension.  
* Le fil jaune est-elle raccordée?  
No sound from the speakers.  
• No sale sonido de los altavoces.  
* ¿Está el cable de salida del altavoz cortocircuitado?  
• El sonido presenta distorsión.  
• Pas de son des haut-parleurs.  
* Is the speaker output lead short-circuited?  
* Le fil de sortie de haut-parleur est-il court-circuité?  
Sound is distorted.  
* Is the speaker output lead grounded?  
• Le son est déformé.  
* Le fil de sortie de haut-parleur est-il à la masse?  
* ¿Está el cable de salida del altavoz conectado a masa?  
* Are the “–” terminals of L and R speakers grounded in common? * ¿Están los terminales “–” de los altavoces L y R conectados a * Les bornes “–” des haut-parleurs gauche et droit sont-elles mises  
Unit becomes hot.  
* Is the speaker output lead grounded?  
una masa común?  
• La unidad se calienta.  
ensemble à la masse?  
• L’appareil devient chaud.  
* Le fil de sortie de haut-parleur est-il à la masse?  
* Are the “–” terminals of L and R speakers grounded in common? * ¿Está el cable de salida del altavoz conectado a masa?  
* ¿Están los terminales “–” de los altavoces L y R conectados a * Les bornes “–” des haut-parleurs gauche et droit sont-elles mises  
una masa común? ensemble à la masse?  
When installing the unit without using the sleeve  
Instalación de la unidad sin utilizar la cubierta  
Lors de l'installation de l’appareil sans utiliser de manchon  
When using the optional stay  
Cuando emplea un soporte opcional  
Lors de l'utilisation du hauban en option  
In a Toyota for example, first remove the car radio and install the unit in its place.  
En un Toyota por ejemplo, primero extraiga la radio del automóvil y luego instale la unidad en su  
lugar.  
Par exemple dans une Toyota, retirer dabord lautoradio et installer lappareil à la place.  
Fire wall  
Tabique a prueba de incendios  
Cloison  
Flat type screws (M5 x 6 mm)*  
Tornillos tipo plano (M5 x 6 mm)*  
* Not included with this unit.  
* No suministrado con esta unidad.  
* Non fourni avec cet appareil.  
Vis à tête plate (M5 x 6 mm)*  
Stay (option)  
Soporte (opción)  
Hauban (en option)  
Washer  
Arandela  
Rondelle  
Bracket*  
Ménsula*  
Support*  
Dashboard  
Tablero de instrumentos  
Tableau de bord  
Lock nut  
Tuerca de seguridad  
Ecrou darrêt  
Pocket  
Screw (option)  
Tornillo (opción)  
Vis (en option)  
Compartimiento  
Poche  
Flat type screws (M5 x 6 mm)*  
Tornillos tipo plano (M5 x 6 mm)*  
Vis à tête plate (M5 x 6 mm)*  
Mounting bolt  
Bracket*  
Ménsula*  
Support*  
Perno de montaje  
Boulon de montage  
Sleeve  
Cubierta  
Manchon  
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If  
longer screws are used, they could damage the unit.  
Nota: Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 6  
mm de longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.  
Remarque: Lors de l'installation de lappareil sur le support de montage, sassurer dutiliser des vis  
dune longueur de 6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager lappareil.  
Retrait de l’appareil  
Avant de retirer lappareil, libérer la section arrière.  
Removing the unit  
• Before removing the unit, release the rear section.  
Extracción de la unidad  
• Antes de extraer la unidad, libere la sección trasera.  
1 Retirer le panneau de commande.  
1 Remove the control panel.  
1 Extraiga el panel de control.  
2 Retirer la plaque dassemblage.  
2 Remove the trim plate.  
2 Retire la placa de guarnición.  
3 Introduire les deux poignées dans les fentes, comme montré.  
Puis, tout en tirant doucement les poignées écartées, faire  
glisser lappareil pour le sortir. (S'assurer de conserver les  
poignées après l’installation de l’appareil.)  
3 Insert the 2 handles into the slots, as shown. Then, while gently 3 Inserte las 2 manijas entre las ranuras, como se muestra.  
pulling the handles away from each other, slide out the unit.  
Luego, separe gentilmente las manijas y extraiga la unidad.  
(Asegúrese de conservar las manijas después de  
instalarlo.)  
(Be sure to keep the handles after installing it.)  
1
3
2
Handle  
Manija  
Poignée  
Parts list for installation and connection  
The following parts are provided with this unit.  
After checking them, please set them correctly.  
Lista de piezas para instalación y conexión  
Con esta unidad se suministran las siguientes piezas.  
Después de inspeccionarlas, colóquelas correctamente.  
Liste des pièces pour l’installation et  
raccordement  
Les pièces suivantes sont fournies avec cet appareil.  
Après vérification, veuillez les placer correctement.  
Hard case/Control Panel  
Sleeve  
Estuche duro/Panel de control  
Etui de transport /Panneau de command  
Cubierta  
Manchon  
Remote controller  
Mando a distancia  
Télécommande  
Power cord  
Trim plate  
Cordón de alimentación  
Cordon dalimentation  
Placa de guarnición  
Plaque dassemblage  
Batteries  
Pilas  
Piles  
CR2025  
Handles  
Manijas  
Poignées  
Washer (ø5)  
Arandela (ø5)  
Rondelle (ø5)  
Lock nut (M5)  
Tuerca de seguridad (M5)  
Ecrou darrêt (M5)  
Mounting bolt (M5 x 20 mm)  
Perno de montaje (M5 x 20 mm)  
Boulon de montage (M5 x 20 mm)  
Rubber cushion  
Cojín de goma  
Amortisseur en caoutchouc  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
ELECTRICAL CONNECTIONS  
CONEXIONES ELECTRICAS  
RACCORDEMENTS ELECTRIQUES  
To prevent short circuits, we recommend that you disconnect the Para evitar cortocircuitos, recomendamos que desconecte el Pour éviter tout court-circuit, nous vous recommandons de  
battery’s negative terminal and make all electrical connections terminal negativo de la batería y que efectúe todas las conexiones débrancher la borne négative de la batterie et deffectuer tous les  
before installing the unit. If you are not sure how to install this unit eléctricas antes de instalar la unidad. Si usted no está seguro de raccordements électriques avant dinstaller lappareil. Si l'on nest  
correctly, have it installed by a qualified technician.  
cómo instalar correctamente la unidad, hágala instalar por un pas sûr de pouvoir installer correctement cet appareil, le faire  
técnico cualificado.  
installer par un technicien qualifié.  
Note:  
This unit is designed to operate only on 12 volts DC, NEGATIVE  
ground electrical systems. If your vehicle does not have this  
system, a voltage inverter is required, which can be purchased at  
JVC car audio dealers.  
Nota:  
Remarque:  
Esta unidad está diseñada para funcionar con 12 voltios de CC, Cet appareil est conçu pour fonctionner sur des sources de courant  
con sistemas eléctricos de masa NEGATIVA solamente. Si su continu de 12 volts à masse NEGATIVE seulement. Si votre  
vehículo no posee este sistema, será necesario un inversor de véhicule noffre pas ce type dalimentation, il vous faut un  
tensión, que puede ser adquirido en los concesionarios de JVC convertisseur de tension, que vous pouvez acheter chez un  
• Replace the fuse with one of the specified rating. If the fuse  
blows frequently, consult your JVC car audio dealer.  
• If noise is a problem...  
This unit incorporates a noise filter in the power circuit. However,  
with some vehicles, clicking or other unwanted noise may occur.  
If this happens, connect the unit’s rear ground terminal (see  
connection diagram below) to the car’s chassis using shorter  
and thicker cords, such as copper braiding or gauge wire. If noise  
still persists, consult your JVC car audio dealer.  
• Maximum input of the speakers should be more than 45 watts at  
the rear and 45 watts at the front, with an impedance of 4 to 8  
ohms.  
Be sure to ground this unit to the car’s chassis.  
• The heat sink becomes very hot after use. Be careful not to  
touch it when removing this unit.  
de equipos de audio para automóviles.  
• Reemplace el fusible por uno con la corriente especificada. Si Remplacer le fusible par un de la valeur précisée. Si le fusible  
el fusible se quemase frecuentemente consulte con su saute souvent, consulter votre revendeur dautoradios JVC.  
concesionario de JVC de equipos de audio para automóviles. Si le bruit est un problème...  
• Si el ruido fuese un problema...  
Esta unidad tiene un filtro de ruido en el circuito de alimentación.  
Sin embargo, en algunos vehículos, pueden producirse  
chasquidos u otros ruidos indeseados. En tal caso conecte el  
terminal de tierra posterior (ver diagrama de conexión abajo)  
del receptor al chasis del automóvil, utilizando cordones más  
gruesos y cortos tales como alambre de cobre trenzado o de  
grueso calibre. Si el ruido persiste, consulte a su concesionario  
de JVC de equipos de audio para automóvil.  
• La entrada máxima de los altavoces traseros debe ser mayor  
de 45 vatios y la de los delanteros de 45 vatios, con una  
impedancia de 4 a 8 ohmios.  
Asegúrese de conectar esta unidad a tierra en el chasis del  
automóvil.  
• El sumidero térmico estará muy caliente después del uso.  
Asegúrese de no tocarlo al desmontar esta unidad.  
revendeur dautoradios JVC.  
Cet appareil incorpore un filtre de bruit dans le circuit  
dalimentation. Cependant, avec certains véhicules, quelques  
claquements ou autres bruits non désirés risquent de se produire.  
Si cela arrive, raccorder la borne de masse arrière de lappareil  
au châssis de la voiture (voir le schéma de raccordement ci-  
dessous) en utilisant des cordons les plus gros et les plus courts  
possibles telle qu'une barre de cuivre ou une tresse. Si le bruit  
persiste, consulter votre revendeur dautoradios JVC.  
La puissance admissible des haut-parleurs doit être supérieure  
à 45 watts à larrière et à 45 watts lavant, avec une impédance  
de 4 à 8 ohms.  
• S'assurer de raccorder la mise à la masse de cet appareil  
au châssis de la voiture.  
Le radiateur devient très chaud après usage. Faire attention de  
ne pas le toucher en retirant cet appareil.  
Heat sink  
Sumidero térmico  
Dissipateur de chaleur  
A Typical Connections / Conexiones típicas / Raccordements typiques  
Before connecting: Check the wiring in the vehicle carefully Antes de la conexión: Verifique atentamente el conexionado Avant de commencer la connexion: vérifiez attentivement le  
not to fail in connecting this unit. Incorrect connection may cause del vehículo para no cometer errores al conectar esta unidad. câblage du véhicule pour ne pas connecter incorrectement cet  
a serious damage to this unit.  
Una conexión incorrecta podría producir daños graves en la appareil. Une connexion incorrecte peut endommager  
unidad. sérieusement lappareil.  
1 Connect the colored leads of the power cord to the car battery,  
speakers and automatic antenna (if any) in the following  
sequence.  
1 Conecte los conductores de color del cable de alimentación 1 Connectez les fils de couleur du cordon dalimentation à la  
a la batería del automóvil, altavoces y antena automática (si  
la hubiere) en la secuencia siguiente.  
1 Negro: a tierra.  
2 Amarillo: a la batería del automóvil (12V constantes)  
3 Rojo: a un terminal de accesorio  
4 Azul con rayas blancas: a la antena automática (máx.  
200mA)  
batterie de la voiture, aux enceintes et à lantenne automatique  
(sil y en a une) dans lordre suivant.  
1 Noir: a la masse  
2 Jaune: a la batterie de la voiture (12V constant)  
3 Rouge: à la prise accessoire  
4 Bleu à bandes blanches: à lantenne automatique (200mA  
max.)  
1 Black: ground  
2 Yellow: to car battery (constant 12V)  
3 Red: to an accessory terminal  
4 Blue with white stripe: to automatic antenna (200mA  
max.)  
5 Orange with white stripe: to car light control switch  
6 Others: to speakers  
5 Naranja con rayas blancas: al interruptor de control de  
las luces del automóvil  
6 Otros: a los altavoces  
5 Orange avec bande blanche: à linterrupteur d’éclairage  
de la voiture  
6 Autres fils: aux enceintes  
2 Connect the antenna cord.  
3 Finally connect the wiring harness to the unit.  
2 Connectez le cordon dantenne.  
2 Conecte el cable de antena.  
3 Por último, conecte a la unidad el cableado preformado.  
3 Finalement, connectez le faisceau de fils à lappareil.  
Before connecting the CD changer, make sure that the unit is  
turned off.  
Antes de conectar el cambiador de CD, asegúrese de que la  
unidad esté apagada.  
Avant de connecter le changeur CD, sassurer que lunité est  
éteinte.  
JVC CD changer or another external  
component  
We recommend that you connect one of the CH-X series CD changers.  
• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).  
You can also use an external component such as a portable MD player by connecting the Line Input  
Adaptor KS-U57 (not supplied). (See diagram B .)  
Recomendamos conectar uno de los cambiadores de CD de la serie CH-X.  
• Si su cambiador de CD es de la serie KD-MK, necesitará un cable opcional (KS-U15K).  
Conectando el adaptador de entrada de línea KS-U57 (no suministrado), también podrá usar un  
componente exterior, tal como un reproductor de MD. (Véase el diagrama B .)  
Nous recommandons que vous connectiez un changeur de CD de la série CH-X.  
Si votre changeur de CD appartient à la série KD-MK, vous avez besoin dun cordon optionnel (KS-  
U15K).  
Cambiador de CD JVC u otro componente  
exterior  
Changeur CD JVC ou autre appareil extérieur  
JVC CD changer jack  
Jack del cambiador de CD de JVC  
Prise de changeur CD JVC  
Line outs  
Vous pouvez aussi utiliser un appareil extérieur tel quun lecteur de MD en connectant ladaptateur  
dentrée de ligne KS-U57 (non fourni) (voir le diagramme B ).  
(see diagram B )  
Salida de línea  
(véase diagrama B )  
Sortie de ligne  
10  
Ignition switch  
Interruptor de encendido  
Interrupteur d'allumage  
Not supplied with this unit.  
No suministrado con esta unidad.  
Non fourni avec cet appareil.  
Rear ground terminal  
Terminal de tierra posterior  
Borne arrière de masse  
(voir le diagramme B )  
*
15A fuse  
Fusible de 15A  
Antenna terminal  
Fusible 15A  
*
Terminal de la antena  
Black  
Borne de lantenne  
Negro  
To metallic body or chassis of the car  
A un cuerpo metálico o chasis del automóvil  
Vers corps métallique ou châssis de la voiture  
*
Noir  
3
2
1
2
To antenna  
To a live terminal in the fuse block connecting to the car battery  
(bypassing the ignition switch).  
A un terminal activo del bloque de fusibles conectado a la  
batería del automóvil (desviando el interruptor de encendido)  
Aune borne sous tension du porte-fusible connectée à la batterie  
de la voiture (en dérivant linterrupteur dallumage)  
Yellow*1  
Amarillo*1  
Jaune*1  
A la antena  
A l'antenne  
1
Red  
Rojo  
Rouge  
Fuse block  
bloque de fusibles  
porte-fusible  
*1: Before checking the operation of this unit prior to installation,  
this lead must be connected, otherwise power cannot be turned  
on.  
*1: Antes de comprobar el funcionamiento de esta unidad previa  
a de la instalación, es necesario conectar este cable, de lo  
contrario no se podrá conectar la alimentación.  
*1: Pour vérifier le fonctionnement de cet appareil avant  
installation, ce fil doit être raccordé, sinon lappareil ne peut  
pas être mis sous tension.  
To an accessory terminal in the fuse block  
A un terminal accesorio del bloque de fusibles  
Vers borne accessoire du porte-fusible  
3
Blue with white stripe  
Azul con rayas blancas  
Bleu avec bande blanche  
To automatic antenna if any  
A la antena automática si la hubiere  
Vers borne dantenne automatique s'il y en a une  
(ILLUMINATION)  
5
4
To car light control switch  
Al interruptor de control de  
las luces del automóvil  
À linterrupteur d’éclairage de  
la voiture  
Orange with white stripe  
Naranja con rayas blancas  
Orange avec bande blanche  
6
Green with black stripe  
Verde con rayas negras  
Vert avec bande noire  
Green  
Verde  
Vert  
White with black stripe  
Blanco con rayas negras  
Blanc avec bande noire  
Gray  
Gris  
Gris  
Purple with black stripe  
Púrpura con rayas negras  
Violet avec bande noire  
Gray with black stripe  
Gris con rayas negras  
Gris avec bande noire  
White  
Blanco  
Blanc  
Purple  
Púrpura  
Violet  
Right speaker (front)  
Altavoz derecho (frontal)  
Haut-parleur droit (avant)  
Left speaker (rear)  
Altavoz izquierdo (trasero)  
Haut-parleur gauche (arrière)  
Left speaker (front)  
Altavoz izquierdo (frontal)  
Haut-parleur gauche (avant)  
Right speaker (rear)  
Altavoz derecho (trasero)  
Haut-parleur droit (arrière)  
PRECAUCIONES sobre las conexiones de la  
fuente de alimentación y de los altavoces:  
PRECAUTIONS sur l’alimentation et la  
connexion des enceintes:  
PRECAUTIONS on power supply and speaker  
connections:  
• NO conecte los conductores de altavoz del cable de • NE CONNECTEZ PAS les fils d’enceintes du cordon  
• DO NOT connect the speaker leads of the power cord to  
the car battery; otherwise, the unit will be seriously  
damaged.  
alimentación a la batería de automóvil, pues podrían  
producirse graves daños en la unidad.  
d’alimentation à la batterie; sinon, l’appareil serait  
sérieusement endommagé.  
Connectez correctement le fil noir (a la masse), le fil jaune (a la  
batterie de la voiture,12V constant) et le fil rouge (à la prise  
accessoire).  
AVANT de connecter les fils denceintes du cordon  
dalimentation aux enceintes, vérifiez le câblage des enceintes  
de votre voiture.  
Si le câblage des enceintes de votre voiture est réalisé  
comme montré sur la Fig. 1 ou Fig. 2 ci-dessous, NE  
CONNECTEZ PAS lappareil en utilisant ce câblage original  
denceintes. Si vous le faites, lappareil sera sérieusement  
endommagé.  
Recommencez le câblage des enceintes de façon que vous  
puissiez connecter lappareil aux enceintes comme montré  
sur la Fig. 3.  
Si le câblage des enceintes de votre voiture est comme  
montré sur la Fig. 3, vous pouvez connecter lappareil en  
utilisant ce câblage original denceintes pour votre voiture.  
Si vous n’êtes pas sûrs du câblage denceintes de votre  
voiture, consulter le concessionnaire de votre voiture.  
• Conecte correctamente el conductor negro (a tierra), el  
conductor amarillo (a la batería del automóvil, 12V constantes),  
y el conductor rojo (a un terminal de accesorio).  
• ANTES de conectar a los altavoces los conductores de altavoz  
del cable de alimentación, verifique el conexionado de altavoz  
de su automóvil.  
• Connect the black lead (ground), yellow lead (to car battery,  
constant 12V), and red lead (to an accessory terminal) correctly.  
• BEFORE connecting the speaker leads of the power cord to  
the speakers, check the speaker wiring in your car.  
If the speaker wiring in your car is as illustrated in Fig. 1  
and Fig. 2 below, DO NOT connect the unit using that original  
speaker wiring. If you do, the unit will be seriously damaged.  
Redo the speaker wiring so that you can connect the unit to  
the speakers as illustrated in Fig. 3.  
If the speaker wiring in your car is as illustrated in Fig. 3,  
you can connect the unit using the original speaker wiring in  
your car.  
– If you are not sure of the speaker wiring of your car, consult  
your car dealer.  
Si el conexionado de altavoz de su automóvil es como  
se indica en las Figs. 1 y 2 de abajo, NO conecte la unidad  
utilizando ese conexionado de altavoz original. Si lo hace,  
se producirán daños graves en la unidad.  
Vuelva a efectuar el conexionado de altavoz de manera que  
pueda conectar la unidad a los altavoces de la manera  
indicada en la Fig.3.  
Si el conexionado de altavoz de su automóvil es como  
se indica en la Fig. 3, podrá conectar la unidad utilizando  
el conexionado de altavoz original de su automóvil.  
– Si tiene dudas sobre el conexionado de altavoz de su  
automóvil, consulte con su concesionario.  
+
+
+
-
+
-
+
L
-
L
+
-
-
L
-
+
+
-
+
+
-
+
R
-
R
+
-
-
R
-
Fig. 2  
Fig. 1  
Fig. 3  
Connecting the leads / Conexión de los conductores / Raccordement des fils  
Solder the core wires to  
CAUTION / PRECAUCION / PRECAUTION:  
connect them securely.  
Suelde los alambres de alma  
para conectarlos con firmeza.  
Souder les âmes desfils pour  
les raccorder entre eux de  
façon sûre.  
To prevent short-circuit, cover the terminals of the UNUSED leads with insulating  
tape.  
Twist the core wires when connecting.  
Retuerza los alambres de alma para  
conectarlos.  
Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.  
Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS utilisés  
avec de la bande isolante  
Torsaderlesâmesdesfilsenlesraccordant.  
B Connections Adding Other Equipment / Conexiones para añadir otros equipos / Raccordement pour ajouter d’autres appareils  
Usted podrá conectar un amplificador y otros equipos para Vous pouvez connecter un amplificateur ou autre appareil pour  
mejorar el sistema estéreo de su automóvil. améliorer votre système autoradio.  
You can connect an amplifier and other equipment to upgrade  
your car stereo system.  
• Connect the remote lead (blue with white stripe) to the remote  
lead of the other equipment so that it can be controlled through  
this unit.  
• Conecte el conductor remoto (azul con rayas blancas) al Connectez le fil de commande à distance (bleu avec bande  
conductor remoto del otro equipo para poderlo controlar a  
través de esta unidad.  
blanche) au fil de commande à distance de lautre appareil de  
façon quil puisse être commandé via cet appareil.  
Pour l'amplificateur seulement:  
• Sólo para el amplificador:  
• For amplifier only:  
– Conecte los terminales de salida de línea de esta unidad  
con los terminales de entrada de línea del amplificador.  
– Desconecte los altavoces de esta unidad y conéctelos al  
amplificador. Los cables de los altavoces de esta unidad  
quedan sin usar. (Cubra los terminales de estos cables  
sin usar con cinta aislante, tal comose indica en la figura  
de arriba.)  
Raccorder les bornes de sortie ligne de cet appareil aux bornes  
dentrée ligne de lamplificateur.  
– Déconnectez les enceintes de cet appareil et connectez-  
les à l’amplificateur. Laissez les fils d’enceintes de cet  
appareil inutilisés. (Recouvrir les extrémités de ces fils  
inutilisés avec de la bande isolante comme montré ci-  
dessus.)  
– Connect this unit’s line-out terminals to the amplifier’s line-in  
terminals.  
– Disconnect the speakers from this unit, connect them to  
the amplifier. Leave the speaker leads of this unit unused.  
(Cover the terminals of the these unused leads with  
insulating tape, as illustrated above.)  
Amplifier / Amplificador / Amplificateur  
Rear speakers  
Altavoces posteriores  
Haut-parleur arrière  
Y-connector (not supplied with this unit)  
Conector en Y (no suministrado con esta unidad)  
Connecteur Y (non fourni avec cet appareil)  
Blue with white stripe  
Azul con rayas blancas  
Bleu avec bande blanche  
INPUT  
JVC Amplifier  
Amplificador de JVC  
L
L
Remote lead  
Cable remoto  
Amplificateur JVC  
R
R
Fil d'alimentation à distance  
To automatic antenna if any  
A la antena automática, si la hubiere  
Vers lantenne automatique, sil y en a une  
Signal cord (not supplied with this unit)  
Cable de señal (no suministrado con esta unidad)  
Cordon de signal (non fourni avec cet appareil)  
LINE OUT  
INPUT  
Front speakers  
Altavoces delanteros  
Haut-parleur avant  
JVC Amplifier  
Amplificador de JVC  
Amplificateur JVC  
L
L
L
REAR FRONT  
R
R
R
KS-FX470  
Front speakers  
You can connect another power  
amplifier for front speakers.  
Podrá conectar otro amplificador Vous pouvez connecter un autre  
Altavoces delanteros  
de potencia para los altavoces amplificateur de puissance pour  
Haut-parleur avant  
delanteros.  
les enceintes avant.  
External component / Componente exterior / Appareil extérieur  
Line Input Adaptor KS-U57 (not supplied with this unit)  
Adaptador de entrada de línea KS-U57 (no suministrado con esta unidad)  
Adaptateur dentrée de ligne KS-U57 (non fourni avec cet appareil)  
L
L
L
L
LINE OUT  
L
R
R
R
R
REAR  
KS-FX470  
R
Signal cord (not supplied with this unit)  
Cable de señal (no suministrado con esta unidad)  
Cordon de signal (non fourni avec cet appareil)  
External component  
Componente exterior  
Appareil extérieur  
CD changer jack  
Toma del cambiador de CD  
Prise du changeur CD  

QSC Audio Car Speaker CSM12 User Manual
Pioneer RS D7RII User Manual
Pioneer DEQ P8000 User Manual
Pioneer Car Stereo System SX 3400 User Manual
Panasonic Palmcorder PV DV202 User Manual
Panasonic Camcorder HDC SD90 User Manual
Orion 5271 User Manual
Nostalgia Electrics KRS 2150 User Manual
Kenwood DPX 504 U User Manual
JVC KW AVX830 User Manual