EN
HD MEMORY CAMERA
U
GZ-HM400
INSTRUCTIONS
To view the INSTRUCTIONS, click below.
Z page 1 - 44
Advanced
INSTRUCTIONS
To view the Advanced INSTRUCTIONS,
click below.
Z page 45 - 94
GUIDEBOOK
Safety Precautions
When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or
more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules or
laws governing the disposal of these batteries must
be followed strictly.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or places
with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
WARNING:TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
NOTES:
The rating plate and safety caution are on the
bottom and/or the back of the main unit.
•
Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fire or electric shock.
The serial number plate is on the battery pack
mount.
•
The rating information and safety caution of the
AC adapter are on its upper and lower sides.
•
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
Carrying or holding the camcorder by the LCD
monitor can result in dropping the unit, or in a
malfunction.
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
or incinerate.
Do not use a tripod on unsteady or unlevel surfaces.
It could tip over, causing serious damage to the
camcorder.
Replace battery with Panasonic, Sanyo, Sony or
Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
CAUTION!
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in fire.
•
Connecting cables (Audio/Video, S-Video, etc.) to the
camcorder and leaving it on top of the TV is not
recommended, as tripping on the cables will cause
the camcorder to fall, resulting in damage.
•
•
For USA-California Only
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material
– special handling may apply.
CAUTION:
The mains plug shall remain readily operable.
Remove the mains plug immediately if the
camcorder functions abnormally.
•
WARNING:
The battery pack, the camcorder with battery
installed, and the remote control with battery
installed should not be exposed to excessive heat
such as direct sunshine, fire or the like.
ꢀ
EN
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
Remember that this camcorder is intended for
private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the
manufacturer.
10.Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer, or
Trademarks
“AVCHD” and the “AVCHD” logo are trademarks
of Panasonic Corporation and Sony Corporation.
•
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
•
x.v.Color™ is a trademark of
Sony Corporation.
•
HDMI is a trademark of HDMI
•
Licensing, LLC.
Windows® is either registered
•
trademark or trademark of
sold with the apparatus.
When a cart is used,
Microsoft Corporation in the
United States and/or other countries.
Macintosh is a registered trademark of Apple
Inc.
iTunes, iMovie, iPhoto are trademarks of Apple
Inc., registered in the U.S. and other countries.
YouTube and the YouTube logo are trademarks
and/or registered trademarks of YouTube LLC.
Other product and company names included in
this instruction manual are trademarks and/or
registered trademarks of their respective holders.
use caution when
moving the cart/
apparatus combination
to avoid injury from tip-over.
11.Unplug this apparatus during lightning storms or
when unused for long periods of time.
12.Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
•
•
•
•
If this symbol is shown, it is only valid
in the European Union.
EN
ꢁ
Easy Start Guide
Charge the battery before recording
Turn off the camcorder and attach the battery pack.
Access lamp
blinks: Accessing files
Power/charge lamp
blinks: Charging
goes out: Charging finished
Do not remove the AC adapter,
the battery pack or the SD
card when the access lamp is
blinking.
The battery pack is not
charged at the time of
purchase.
Battery Pack
AC Adapter
To AC Outlet
(110V to 240V)
CAUTION
Fire or injury may result if batteries NOT approved by JVC are used. Only use the
batteries specified on page 41.
ꢂ
EN
Select the city closest to
the area where you use
the camcorder
Date/Time Setting
T
Open the LCD monitor to
Q turn on the camcorder
Power button
LCD monitor
Select [ON] if daylight
saving time is observed
U
V
Select [YES] within
R 10 seconds
Slide your finger up and down on the
sensor. Then touch OK.
Set the date and time
Touch sensor: Sets the date and time
: Moves the cursor to the right
OK: Clock starts
&
When the message disappears, press the
•
power button for at least 2 seconds to turn
off the power, and then press it again for at
least 2 seconds.
Touch the sensors with your finger. The
sensors do not function if you touch them
with your finger nail or with gloves on.
•
Select [CLOCK SETTING]
S
EN
ꢃ
Video recording
CAUTION
Before recording an important scene, it is recommended to conduct a trial
recording.
Slide the mode switch to select ! (video) mode
Q
Select recording mode (REC)
R
The mode changes when
you press the button.
The auto recording
indicator appears.
Start recording
S
Remaining space on
the recording media
Record-standby
Video Quality
Press the START/STOP
button to start recording,
and press it again to stop.
Recording
ꢄ
EN
Playing back
Select playback mode (PLAY)
Q
The mode changes when
you press the button.
Select the desired file
R
S
Index screen
Select
(Touch OK)
F
Playback screen
To perform operations such as forward search or reverse search (Z p. 22)
To view files on TV (Z p. 24)
CAUTION
Do not forget to make copies after recording!
To copy files onto discs (Z p. 26)
To dub files to a VCR/DVD recorder (Z p. 28)
To edit files on your computer (Z p. 29)
•
•
•
EN
ꢅ
Attaching the Core Filter to the USB Cable... 11
Viewing Files on TV .................................... 24
Playback Operation ...................................... 25
Index ............................................................ 12
Grip Adjustment............................................ 17
Using an SD Card......................................... 18
Uploading Files............................................. 35
Cautions ...................................................... 42
Terms........................................................... 44
Playing Back Files...................................... 22
Video Playback ............................................ 22
Still Image Playback ..................................... 23
Read these INSTRUCTIONS to enjoy your CAMCORDER.
For more details on the operations, refer to the Advanced INSTRUCTIONS in the
supplied CD-ROM.
In order to view the Advanced INSTRUCTIONS, Adobe® Acrobat® ReaderTM or
Adobe® Reader® must be installed.
Adobe® Reader® can be loaded from Adobe’s web site:
NOTE
Select your desired language with a single click.
The model name is indicated on the bottom of your camcorder.
ꢆ
EN
How to use the Touch
Sensor
After the menu is displayed on the LCD
monitor:
Read This First!
Make a backup of important recorded data
It is recommended to copy your important
recorded data to a DVD or other recording
media for storage. JVC will not be responsible
for any lost data.
Make a trial recording
Before the actual recording of important data,
make a trial recording and play back the
recorded data to check that the video and
sound have been recorded correctly.
Reset the camcorder if it does not operate
correctly
Close the LCD monitor and remove the power
supply (battery pack or AC adapter) from the
camcorder, then reattach it.
QSlide your finger up and down on the
sensor.
RSelect [SET]. (Touch OK.)
Precautions on handling batteries
Be sure to use the JVC BN-VF808U/
•
VF815U/VF823U battery packs. This product
includes patented and other proprietary
technology and is made to be used with the
JVC battery and not with other batteries.
JVC cannot guarantee safety or
performance of this product when it is
operated by other batteries.
If the camcorder is subjected to electrostatic
discharge, turn off the power before using it
again.
•
A
If a malfunction occurs, stop using the
camcorder immediately and contact
To select an on-screen button appearing on
the left side, touch the portion of the sensor
next to the on-screen button.
Recorded data may be erased while the
•
B
To select an on-screen button appearing at
the bottom of the screen, touch the buttons
underneath them.
camcorder is being repaired or inspected.
Back up all data before requesting repairs or
inspections.
Because camcorders may be used
for demonstration in a shop, the
demonstration mode is set to on by default
To deactivate the demonstration mode, set
[DEMO MODE] to [OFF].
EN
ꢇ
GETTING STARTED
Accessories
Shoe Adapter
An optional microphone or light can be
attached to the shoe adapter.
AP-V21U
AC Adapter
BN-VF815U
Battery Pack
Slide the shoe cover
in the direction of the
arrow to reveal the shoe
adapter mounting socket.
Component Cable
AV Cable
Mount the accessory
shoe adapter.
LY37115-001A
USB Cable
Shoe Adapter
Fasten the shoe adapter
to the shoe adapter
mounting socket by
turning the screw in the
direction of the arrow.
RM-V751U
CR2025
Remote Control
Lithium Battery
Pre-installed in the
remote control.
Insert a microphone, etc.
from behind the shoe
adapter.
CD-ROM
Core Filter
NOTE
Do not try to attach a microphone, etc. to the
shoe adapter forcibly.
NOTE
Make sure to use the provided cables for
connections. Do not use any other cables.
10 EN
Preparing the Remote Control
Attaching the Core Filter to the USB
Cable
A battery is included inside the remote control
at the time of purchase.
Remove the insulation sheet before use.
The core filter reduces interference caused
when connecting to other devices. Connect
the end of the cable with the core filter to the
camcorder.
Beam Effective Area
Remote Sensor
Release the stopper.
Effective distance:
Max. 4 m (13.16 ft)
NOTE
The transmitted beam may not be effective
or may cause incorrect operation when the
remote sensor is directly exposed to sunlight
or powerful lighting.
3 cm (1-3/16")
To Reinsert the Battery
To be connected to
the camcorder
Pull out the battery holder by pressing the lock
tab.
Lock Tab
Lithium Battery
(CR2025)
Wind once.
EN 11
Camcorder
Remote Control
! Power Button
# SD Card Slot
Q Infrared Beam Transmitting Window
R ZOOM (T/W) Buttons (Zoom in/Out)
S Up Button
T Skip Backward Button
U Left Button
$ OPEN knob (Z p. 18)
% Speaker
& PLAY/REC Button (Z p. 19, 20, 22, 23)
( SNAPSHOT Button (Z p. 20)
) Touch Sensor
V Back Button
W PLAYLIST Button
X START/STOP Button
Y S.SHOT(SNAPSHOT) Button
Z INFO Button
a Skip Forward Button
b PLAY/PAUSE/SET Button
c Right Button
* OK Button
+ MENU Button (Z p. 36)
, USB Connector (Z p. 26, 30)
- Mode Switch [!, #]
. EXPORT Button (Z p. 34)
/ DIRECT DISC Button (Z p. 27)
INFO Button (Z p. 21)
d Next Button
0 DISPLAY Button (Z p. 15)
1 UPLOAD Button (Z p. 35)
TITLE Button
e Down Button
f INDEX Button*
g DISP Button
2 Lens
3 Flash (Z p. 21)
4 Shoe Adapter Mounting Socket (Z p. 10)
5 Remote Sensor
6 Zoom Lever (Z p. 21)
Speaker Volume Control
7 Aperture Priority Setting Button [A]
8 Shutter Speed Button [S]
9 USER Button [U]
* Each time you press INDEX, the screen
switches as shown below:
! mode:
Index Screen « Group Index Screen
# mode:
Index Screen « Date Index Screen
Tripod Mounting
: Adjustment dial/SET Button
; FOCUS/BRIGHT Switch
< HDMI Mini Connector (Z p. 24)
= Component Connector (Z p. 24)
Align the camcorder stud hole with the tripod
stud, and the mounting socket with the screw,
and then rotate the camcorder clockwise to
mount it to the tripod.
>
(headphones) Connector
? DC Connector
@ START/STOP Button (Z p. 19)
A AV Connector (Z p. 25, 28)
B MIC (microphone) Connector
C Stereo Microphone
D Battery Release Button (Z p. 16)
E Tripod Mounting Socket
NOTE
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
EN 1ꢁ
Indications on LCD Monitor
During both Video and Still Image
Recording
During Video Recording Only
DEC. 24. 2009 4:55 PM
! Mode Indicator
# High Speed Recording Indicator
$ Upload Mode Indicator (Z p. 35)
% Counter
& Export Mode Indicator (Z p. 34)
( Video Quality
! Selected Recording Mode Indicator
(Z p. 19, 20)
: Auto Mode
@
3: Manual Mode
# Scene Select Indicator
) Remaining Time
$ Effect Mode Indicator
*
REC: (Appears during recording.)
M
% White Balance Indicator
& Tele Macro Mode Indicator
( Zoom Indicator (Z p. 21)
) Recording Medium Indicator
* Focus Assist Indicator
+ Optical Image Stabilizer (OIS) Indicator
, Monitor Backlight Indicator
- Battery Indicator
: (Appears during record-standby mode.)
MQ
+ Continuous Shooting Indicator
, Shooting Indicator (Z p. 19)
- Wind Cut Indicator
. Microphone Input Level Indicator
/ Event Indicator
0 Sharpness Indicator
1 x.v.Color™
. Date/Time (Z p. 16)
/ Manual Focus Adjustment Indicator
0 Aperture Value (F-number)
1 Backlight Compensation Indicator
: Face Detection indicator
During Still Image Recording Only
2 Brightness Control Indicator
.: Photometry Area Control Indicator
3 Shutter Speed
! Mode Indicator
# ISO Sensitivity Indicator (When [GAIN] is
set to [AUTO], there is no indication.)
$ Flash Indicator (Z p. 21)
% Focus Indicator (Z p. 20)
& Image Size
STD
( Image Quality: FINE (fine) or
(standard)
) Remaining Number of Shots
* Shooting Indicator (Z p. 20)
+ Continuous Shooting Indicator
: Bracketing Indicator
, Self-Timer Indicator
J
1ꢂ EN
During Video Playback
During Still Image Playback
8
DEC. 24. 2009 4:55 PM
DEC. 24. 2009 4:55 PM
! Mode Indicator
! Mode Indicator
# Quick Review Indicator (Z p. 20)
$ Folder/File Number
% Slide Show Playback Indicator
& Recording Medium Indicator
( Battery Indicator
# High Speed Recording Indicator
$ Playlist Playback Indicator (Appears when
playing back a playlist.)
% Quick Review Indicator (Z p. 19)
: Digest Playback Indicator
& Video Quality
) Date/Time (Z p. 16)
( Counter
) Playback Mode
* Face Detection Zoom Indicator
+ Output with 1080p
Playback
Pause
Forward Search
Reverse Search
Forward Slow-Motion
Reverse Slow-Motion
:
:
:
:
F
Q
K
J
Switching indication modes on LCD
monitor
Each time you touch DISPLAY, indications
on LCD monitor switch as shown below:
:
:
QF
PQ
In recording mode:
(The number on the left shows speed.)
All indications/Indications for selected
functions
In playback mode:
All indications/Only date and time/No
indications
* Recording Medium Indicator
+ Battery Indicator
, Date/Time (Z p. 16)
- Volume Level Indicator
. Wipe/Fader Effect Indicator
/ x.v.Color™
0 Output with 1080p
EN 1ꢃ
Necessary Settings before Use
NOTE
Charging the Battery Pack
You can also use the camcorder with just the
AC adapter.
•
•
The actual recording time may shorten
depending on the recording environment,
such as when recording scenes with fast
moving subject.
Please do not pull or bend the AC adapter
plug and cable. This may damage the AC
adapter.
1 Close the LCD monitor to turn off the
camcorder.
2 Attach the battery pack, then connect
•
the AC adapter.
Date/Time Setting
1 Open the LCD monitor to turn on the
camcorder.
2 Touch MENU.
AC Adapter
To AC Outlet
(110V to 240V)
3 Select [DISPLAY SETTINGS].
The power/charge lamp blinks to
indicate charging has started.
•
When the lamp goes out, charging is
finished.
•
4 Select [CLOCK ADJUST].
Recording
Battery pack Charging time
time
BN-VF808U
1 h 50 m
2 h 40 m
3 h 40 m
1 h 10 m
2 h 25 m
3 h 40 m
BN-VF815U
(Provided)
BN-VF823U
5 Select [CLOCK SETTING].
To check the remaining battery power
See page 21.
To detach the battery pack
6 Select the city closest to the area
where you use the camcorder.
Selected area is highlighted
Principal city of the
selected area
Time difference to
GMT
1ꢄ EN
7 Select [ON] if daylight saving time is
Language Setting
observed.
The language on the display can be changed.
1 Open the LCD monitor to turn on the
camcorder.
2 Touch MENU.
8 Set the date and time.
3 Select [DISPLAY SETTINGS].
Change the setting by using the touch
sensor and select [ ] to set.
&
4 Select [LANGUAGE].
9 Select [SAVE].
To reset the setting, select [CANCEL].
Setting the clock to local time when
traveling
After performing steps 1-4 (Z p. 16)
5 Select the desired language.
5 Select [AREA SETTING].
To return to the previous screen
Select
.
@
To quit the screen
Select [QUIT].
Grip Adjustment
6 Select the city closest to the area you
are traveling.
To return to the previous screen
Select
.
@
NOTE
To quit the screen
Select [QUIT].
Fasten the strap when you grip the
•
camcorder.
When carrying the camcorder, please be
careful not to drop it.
•
EN 1ꢅ
Other Settings
3 Close the SD card cover.
Using an SD Card
The camcorder is programmed to record on
the built-in memory when it is shipped from the
factory.You can change the recording medium
to an SD card.
Operations are confirmed on the following
SD cards.
- Panasonic
•
To remove an SD card
Push the SD card once.
After the card comes out a little, pull it out.
- TOSHIBA
- SanDisk
- ATP
Video recording:
Class 4 or higher compatible SDHC card
(4 GB to 32 GB)
Still image recording:
SD card (256 MB to 2 GB) or SDHC card
(4 GB to 32 GB)
NOTE
Insert and remove the SD card only while the
power is turned off. Otherwise, data on the
card may be corrupted.
•
Do not touch the terminal on the reverse side
of the label.
•
Operations are not guaranteed if any other
•
SD card than the mentioned above is used.
If other media are used, they may fail to
record data correctly, or they may lose data
that had already been recorded.
MultiMediaCards are not supported.
Video data may not be recorded onto the
SD cards on which video data have already
been recorded using the devices from other
manufacturers.
•
Change the recording medium
Set [MEDIA SETTINGS]
[REC MEDIA
&
•
FOR VIDEO] and [REC MEDIA FOR
IMAGE] to [SD CARD].
•
It is recommended to use Class 6 when
recording video in UXP mode.
•
NOTE
No SD card is supplied with your camcorder.
Format an SD card when using it for the
first time
Insert an SD card
Preparation:
Press the < (Power) button for more than
2 seconds to turn off the camcorder.
Select [MEDIA SETTINGS]
[FORMAT
&
SD CARD] to format the card.
1 Slide the OPEN knob to open the SD
card cover.
2 Firmly insert the card with its clipped
edge first.
OPEN Knob
1ꢆ EN
RECORDING/PLAYBACK
Recording Files
Video Recording
Slide the mode switch to select
! (video) mode.
Press PLAY/REC to select the
recording mode.
SNAPSHOT
Press START/STOP to start
recording.
Approximate remaining
time for recording
You can also start/stop recording by
selecting [REC] on the LCD monitor.
(On-screen recording control)
NOTE
To stop recording
Press START/STOP again.
The video recording mode is automatically
selected when you turn off the camcorder
and then turn on again.
•
To view the last recorded scene
Select while recording is paused.
A
If the camcorder is not operated for 5
minutes while the power is on, it turns itself
off automatically to conserve power.
•
Selecting $ during playback deletes that
scene.
To record a still image during video
recording
Press SNAPSHOT.
To change the video quality
Change the settings in [VIDEO QUALITY].
To change the manual recording mode
Select [A/M] twice.
EN 1ꢇ
Recording Files (Continued)
Still Image Recording
Slide the mode switch to select
# (still image) mode.
Press PLAY/REC to select the
recording mode.
Press and hold SNAPSHOT
halfway.
The ? indicator becomes green when
the captured image is focused.
Press SNAPSHOT fully to take a
still image.
To view the last recorded image
Select
after shooting.
A
Selecting $ during playback deletes that
image.
To change the image quality
Change the settings in [IMAGE QUALITY].
To change the image size
Change the settings in [IMAGE SIZE].
NOTE
To record still images continuously
Set to [CONTINUOUS SHOOTING] in
[SHUTTER MODE].
If the camcorder is not operated for 5
minutes while the power is on, it turns itself
off automatically to conserve power.
The sides of still images recorded in 16:9
size may be cut off when printed. Check
whether 16:9 size prints can be printed at
your local print store.
•
•
To change the manual recording mode
Select [A/M] twice.
ꢀ0 EN
NOTE
Zooming
The flash does not work during [CONTINUOUS
SHOOTING] and [BRACKETING].
The flash does not work with the following
SCENE SELECT settings.
[LANDSCAPE] [TWILIGHT] [NIGHT] [SNOW]
[BEACH] [FIREWORKS] [SUNSET]
It is recommended shoot distance within 2 m
(6.6 ft).
•
•
Preparation:
Select ! or # mode.
•
Select the recording mode.
•
Zoom in
Zoom out
•
Checking the Remaining Space on
the Recording Media
T: Telephoto
W: Wide angle
You can also zoom out/zoom in by selecting [W] or
[T] on the LCD monitor. (On-screen zoom control)
Preparation:
Select ! mode.
•
Zoom ratio (factory-preset)
Select the recording mode.
•
! mode
[10X/OPTICAL]
# mode
[10X/OPTICAL]
Press INFO.
Selected recording medium only
To change the maximum zoom ratio
(! mode only)
Change the settings in [ZOOM].
NOTE
The maximum recording time is displayed for
each video quality mode.
Macro shooting is possible as close as approx.
5 cm (2") to the subject when the zoom lever is
set all the way to W.
To change the video quality
1) Select the video quality.
2) Select [SET].
Flash
To quit the screen
Select [QUIT].
Preparation:
Select # mode.
•
Select the recording mode.
•
Checking the Remaining Battery
Power
1 Touch MENU.
2 Select [FLASH].
! mode:
Press INFO and then select
.
;
3 Select the desired setting.
# mode:
Disables this function.
Press INFO.
1 OFF
The flash fires automatically.
AUTO
The flash fires automatically
but reduces the red-eye
phenomenon of the subject’s
eyes.
AUTO
RED-EYE
The flash fires regardless of the
shooting condition.
( ON
To quit the screen
Select [QUIT] or press INFO.
The flash fires. The shutter
speed becomes slower, so
that background can also be
brightened.
SLOW
SYNCHRO
NOTE
The recordable time display should only be used
as a guide. It is displayed in 10 minute units.
EN ꢀ1
Playing Back Files
Video Playback
Press PLAY/REC to select the
playback mode.
Slide the mode switch to select !
(video) mode.
The index screen appears.
Select the desired file.
To move to the previous or next page
Touch [ ] or [ ] for over a second.
Operations during Video Playback —
On-screen buttons
To play back a few seconds from the
beginning of each video
Return to the first scene of the file
Go to the first scene of the next file
Return to the index screen
:
:
:
:
:
N
O
L
J
E
Touch [
].
Reverse search (during playback)
Frame-by-frame playback in reverse
NOTE
direction (during pause)*
In some cases, parts of video other than the
beginning may be played back.
Some video may not be played back at all.
•
•
Playback
:
:
:
:
F
Q
K
G
Pause
Forward search (during playback)
To delete a video
Frame-by-frame playback in forward
Select $ when playback is stopped.
To change the number of thumbnails
(6 thumbnails/12 thumbnails)
direction (during pause)*
* Slow playback starts when you keep touching
the sensor button under
/
for a while.
E G
Move the zoom lever to [W].
Speaker volume
To zoom in the video during pause
(Remote Control Only)
Press T on the remote control.
+ : Turn up the volume
Press ¡, ¢, £, ¤ on the remote control to
•
move the zoom area.
Press and hold W on the remote control to
•
cancel zoom in.
— : Turn down the volume
ꢀꢀ EN
Still Image Playback
Press PLAY/REC to select the
playback mode.
Slide the mode switch to select #
(still image) mode.
The index screen appears.
Select the desired file.
To move to the previous or next page
Touch [ ] or [ ] for over a second.
Operations during Still Image Playback
— On-screen buttons
To delete a still image
Select $.
To change the number of thumbnails
(6 thumbnails/12 thumbnails)
Play the slide show in reverse direction
Play the slide show in forward direction
Return to the index screen
Display the previous file
:
:
:
:
:
:
:
P
F
L
N
F
Q
O
Move the zoom lever to [W].
Start the slide show
To zoom in the image during playback
(Remote Control Only)
Press T on the remote control.
End the slide show
Display the next file
Rotate 90 degrees counterclockwise
(during playback)
:
Press ¡, ¢, £, ¤ on the remote control to
•
move the zoom area.
Press and hold W on the remote control to
•
cancel zoom in.
Rotate 90 degrees clockwise (during
playback)
:
NOTE
The playback zoom does not function while
slide show.
EN ꢀꢁ
USING WITH TV
Viewing Files on TV
This camcorder is designed to be used with
high-definition or NTSC-type color television
signals. It cannot be used with a television of a
different standard.
NOTE
When connecting to the HDMI cable, the
•
image or sound may not appear on the TV
properly depending on the TV connected.
In such cases, perform the following
operations.
Connection with TV
1) Disconnect the HDMI cable and
connect it again.
2) Turn off and on the camcorder again.
You can output videos from the HDMI
connector, COMPONENT connector, or AV
connector. Select the connector that best suits
your television.
To connect using the COMPONENT
connector
Preparation:
Turn off all units.
AV Connector
To connect using the HDMI mini
connector
COMPONENT Connector
We recommend using the Category 2 HDMI
cable (High Speed cable).
HDMI Mini Connector
DC Connector
Component
AC Adapter
Cable
To AC Outlet
DC Connector
AC Adapter
AV Cable
HDMI Cable (optional)
(Mini to full-sized HDMI cable)
To AC Outlet
COMPONENT
Input Connector
Audio L/R Input
Connector
Video Connector
is not in use.
HDMI Connector
NOTE
Change the settings in [COMPONENT
OUTPUT] according to the connection.
ꢀꢂ EN
To connect using the AV connector
Playback Operation
AV Connector
After the connection with TV is completed
1 Turn on the camcorder and the TV.
2 Set the TV to its VIDEO mode.
3 (Only when connecting the camcorder to
the VCR/DVD recorder)
Turn on the VCR/DVD recorder, and
set the VCR/DVD recorder to its AUX
input mode.
DC Connector
AC Adapter
4 Start playback on the camcorder.
(Z p. 22, 23)
To display camcorder’s on-screen
display on TV
To AC Outlet
Set [DISPLAY ON TV] to [ON].
AV Cable
NOTE
When the video was recorded with x.v.Color™
set to [ON], change the x.v.Color™ setting on
TV. For details, refer to the TV’s instruction
manual.
AV Input Connector
NOTE
Change the settings in [VIDEO OUTPUT] to
suit the screen size of your television.
EN ꢀꢃ
COPYING
Copying Files
Types of Copying and Connectable Device
Using a BD/DVD Burner
The Camcorder
You can copy files between the
built-in memory and the SD card
with this camcorder alone.
The files in the camcorder can be backed up to
a disc using a BD/DVD burner.
Use one of the following methods to view
•
the disc. (If you try to play back the disc with
incompatible player, the disc may not be
ejected.)
DVD Burner
CU-VD50/CU-VD3
You can copy files recorded on
this camcorder onto discs.
- Playing back the disc in the BD/DVD burner
using the camcorder.
- Playing back the disc using a BD/DVD
burner.*
- Playing back the disc on a PC.*
- Playing back the disc using a BD/DVD player
that supports BD-MV and AVCHD.*
* The DVD must first be finalized using the
camcorder’s menu.
BD Burner
LaCie Model No. 301828
LG Model No.BE06LU10
You can copy files recorded on
this camcorder onto discs.
Only the BD/DVD created from the
•
USB External Hard Disk Drive
You can copy files recorded
on this camcorder onto a USB
external hard disk drive.
camcorder can be played by operating the
BD/DVD burner while connected to the
Camcorder.
When connecting the DVD burner CU-VD50
•
to a TV, you can play back the created disc
without using the camcorder. When playing
back disconnect the USB cable.
PC
You can copy files from the
camcorder to a disc using a PC.
Connection with a BD/DVD Burner
Preparation:
VCR/DVD Recorder
Turn on the camcorder first, then turn on the
BD/DVD burner.
You can dub video recorded on
this camcorder onto VCR/DVD
recorder.
USB Connector
DC Connector
NOTE
It is recommended to use the JVC DVD
•
burner CU-VD50 or CU-VD3. If you use
CU-VD20 or CU-VD40, the recording time
may take approx. 2 times longer than the
time that is described in the instruction
manual of DVD burner.
Recommended USB external hard disk drive
•
Seagate
LaCie
FreeAgent™ Desk series
Design by Neil Poulton series
AC Adapter
USB external hard disk drive with the capacity
over 2 TB cannot be used.
•
USB Cable
BD/DVD Burner
To AC Outlet
USB Connector
ꢀꢄ EN
NOTE
4 Select [YES] or [NO].
Refer also to the BD/DVD burner’s instruction
manual.
•
•
•
[YES]: Displays the thumbnails by group.
•
[NO]: Displays the thumbnails by date or
by playlist.
•
When connecting to a DVD burner, use the USB
cable that came with the DVD burner.
When connecting to a BD burner, use a
USB cable with Mini-A(Male) to B(Male)
connectors. JVC’s QAM0852-001 (optional) is
recommended. Refer to page 35 for information
on contacting JVC.
5 Select [EXECUTE].
The files are copied on the disc. When
[COMPLETED] appears, touch OK.
•
When [INSERT NEXT DISC PRESS
•
[STOP] TO EXIT CREATE] appears,
change the disc. Remaining files are
copied on the second disc.
Backup All Files
Preparation:
To cancel copying, select [STOP].
•
Select ! or # mode.
•
Select built-in memory or SD card to copy
from.
•
Copying Video Files that Have Never
Been Copied
Connect the camcorder to the BD/DVD
burner.
When using a BD burner, select [CHANGE
REC. MEDIA] and select the disc type.
•
•
Files that have never been copied to the discs
are automatically selected and copied.
1 Select [CREATE FROM ALL] (!
1 Press the < (Power) button for
more than 2 seconds to turn on the
camcorder.
mode) or [SAVE ALL] (# mode).
2 Press DIRECT DISC.
2 Select the desired setting.
3 Select [YES] or [NO].
[YES]: Displays the thumbnails by group.
[NO]: Displays the thumbnails by date or
by playlist.
•
•
! mode: [ALL SCENES]
•
•
# mode: [ALL IMAGES]
All files in the recording medium are copied.
! mode: [UNSAVED SCENES]
# mode: [UNSAVED IMAGES]
Files that have never been copied are
automatically selected and copied.
4 Select [EXECUTE].
3 Select [EXECUTE].
The files are copied on the disc. When
[COMPLETED] appears, touch OK.
•
When [INSERT NEXT DISC PRESS
•
[STOP] TO EXIT CREATE] appears,
change the disc. Remaining files are
copied on the second disc.
To cancel the disc creation, select
[CANCEL].
•
EN ꢀꢅ
Copying Files (Continued)
1 Press the < (Power) button for
more than 2 seconds to turn on the
camcorder.
To quit the screen
1) Select [QUIT].
2) When [QUIT?] appears, select [YES].
NOTE
2 Set the VCR/DVD recorder to its AUX
This method can be used to copy video files to
discs in a computer connected to the camcorder.
input mode.
Check that the images from the camcorder
are input correctly to the VCR/DVD
recorder.
Dubbing Files to a VCR/DVD Recorder
Preparation:
3 Play back playlists on the camcorder.
Create a playlist.
Turn off all units.
•
1) Touch MENU.
•
2) Select [DUBBING PLAYBACK].
3) Select the desired playlist.
4) Select [YES]. (A black screen is
displayed for 5 seconds at the beginning
and the end of the footage.)
To connect using the AV connectors
(analog dubbing)
AV Connector
4 At the point you want to start
dubbing, start recording on the VCR/
DVD recorder.
Refer to the VCR/DVD recorder’s
instruction manual.
To stop dubbing
Stop recording on the VCR/DVD recorder.
DC Connector
AC Adapter
To hide the date or icons on the screen
Change the settings in [DISPLAY ON TV]
before dubbing.
Switching indication modes on LCD
monitor
Each time you touch DISPLAY, indications
on LCD monitor switch as shown below:
AV Cable
In recording mode:
To AC Outlet
All indications/Indications for selected
functions
In playback mode:
All indications/Only date and time/No
indications
VCR/DVD Recorder
AV Connector
(Input)
ꢀꢆ EN
PC OPERATION
Creating a Disc Using a PC
You can copy the data from the camcorder and
1 Click [Easy Installation].
create a disc using a PC.
Installing the software to the PC
Q
System Requirements
Windows Vista
OS: Windows Vista®
Follow the on-screen instructions.
Home Basic (SP1)
Home Premium (SP1)
(32-bit, pre-installed)
2 Click [Next].
CPU: Intel® CoreTM Duo, 1.66 GHz or higher
(Intel® CoreTM 2 Duo 2.13 GHz or higher
recommended.)
RAM: At least 2 GB
Windows XP
OS: Windows® XP
Home Edition (SP2/SP3)
Professional (SP2/SP3)
(pre-installed)
3 Click [Finish].
CPU: Intel® CoreTM Duo, 1.66 GHz or higher
(Intel® CoreTM 2 Duo 2.13 GHz or higher
recommended.)
RAM: At least 1 GB
Everio MediaBrowser icons are created on
the desktop.
To check the PC specification
Right-click on [Computer] (or [My
Computer]) in the [Start] menu and select
[Properties].
NOTE
Make sure your PC has a recordable BD/
DVD drive.
If your system does not meet the
requirements, it is recommended to copy
•
Everio MediaBrowser Player is a software
that plays AVCHD discs on the PC.
(DVD discs cannot be played.)
•
files using a BD/DVD burner. (Z p. 26)
To see the Instruction Guide for Everio
MediaBrowser
Preparation:
Load the provided CD-ROM into the PC.
In Windows Vista, the auto play dialog box
appears.
1) Double-click the icon of Everio
MediaBrowser.
2) Click [Help], and click [MediaBrowser Help].
Click
Click
EN ꢀꢇ
Creating a Disc Using a PC (Continued)
Making Backup on the PC
R
3 Click [All volume in camcorder] and
click [Next].
Preparation:
Install the software to the PC.
Make sure that enough free space is left in
the PC’s HDD.
•
•
Press the < (Power) button for more than
2 seconds to turn off the camcorder.
•
USB Connector
4 Click [Start].
Power button
USB Cable
Backup starts.
To disconnect the camcorder from the
PC
1) Right-click the icon (Safely Remove
Hardware) on the task bar and select
[Safely remove USB Mass Storage
Device].
2) Follow the on-screen instructions and
make sure that the device can be safely
removed.
3) Disconnect the USB cable and close the
LCD monitor.
USB Connector
1 Press the < (Power) button for
more than 2 seconds to turn on the
camcorder.
NOTE
It takes time to back up many videos.
2 Select [BACK UP].
Everio MediaBrowser starts on the PC.
ꢁ0 EN
Making User Lists to Arrange the
Files
S
5 Click the recording date.
You can make a user list of a certain subject
(such as Travel, Athletic meet) and put the files
related to the subject into the user list.
Preparation:
Make backup on the PC.
The files recorded on the day are displayed.
1 Double-click the icon to open the
calendar.
6 Drag and drop the file into the user
list.
2 Select [Movies only].
To add other files into the user list, repeat
steps 5 and 6.
3 Click [+].
4 Input the name of the new user list
and click [OK].
EN ꢁ1
Creating a Disc Using a PC (Continued)
Copying Files to a disc
T
4 Drag and drop the file, into the part at
the bottom and click [Next].
Everio MediaBrowser supports 3 disc formats.
Select the one that suits your purpose.
DVD-Video
disc:
Suitable if you will give the disc
to your friends and relatives.
AVCHD disc: Suitable for high quality video.
BD:
Suitable for high quality video
with long recording time.
5 Input the disc name, select the top
1 Select the user list and click [Create
menu style and click [Next].
Disc].
6 Click [Start].
2 Select the disc type and click [Next].
NOTE
3 Click [Select files individually] and
When copying video recorded in UXP
•
click [Next].
recording mode to create an AVCHD disc,
the video needs to be converted to XP
recording mode before copying. Therefore,
it may take longer time than copying video
recorded in other modes.
To add all the files onto discs, click [Select
all files displayed], then go to step 5.
Use Everio MediaBrowser Player to play
•
back the disc. Refer to the help of the
provided Everio MediaBrowser software to
operate.
For detail on operating Everio MediaBrowser,
•
click [Help] and refer to [MediaBrowser Help].
Adobe® Reader® must be installed to read
•
[MediaBrowser Help]. Adobe® Reader® can
be downloaded from Adobe’s web site:
For assistance in operating the provided
software, refer to the support information.
•
(Z p. 35)
ꢁꢀ EN
Folder Structure and Extensions
EVERIO_MEM
EVERIO_SD
X = number
Contains the still image folders.
[DCIM]
[XXXJVCSO]
[DCIM]
[XXXJVCSO]
Video files with defective
management information are
saved.
[EXTMOV]
[DEM_XXXX.MTS]
[MOV_XXXX.MTS]
[EXTMOV]
[DEM_XXXX.MTS]
[MOV_XXXX.MTS]
[PRIVATE]
Contains management information
files of event and/or disc creation
information for the files taken with
the camcorder.
[PRIVATE]
[AVCHD]
[BDMV]
[STREAM]
[XXXXX.MTS]
[JVC]
[AVCHD]
[BDMV]
[STREAM]
[XXXXX.MTS]
Video file in AVCHD format
[BACKUP]
[BACKUP]
[CLIPINF]
[CLIPINF]
[PLAYLIST]
[INDEX.BDM]
[MOVIEOBJ.BDM]
[PLAYLIST]
[INDEX.BDM]
[MOVIEOBJ.BDM]
For Macintosh users
To copy files to a computer
1) Connect the camcorder to the computer with the USB cable.
2) Select [PLAYBACK ON PC].
3) Click [EVERIO_MEM/EVERIO_SD] displayed on the computer screen.
4) Click
.
Search the files you want referring the folder structure above.
5) Copy files to any folder on the PC (such as the desktop).
Click
Copy
(The screen is the image of Mac OS X.)
To edit files
Use the software compatible with AVCHD/JPEG.
NOTE
Do not move or delete the folders and the files in the camcorder.
EN ꢁꢁ
Using with a Portable Media Player
Turning on the Export Mode
To cancel the export setting
Select the file and select [
] again.
You can easily transfer videos recorded in
export mode to iTunes®. All the files with the
export setting turned on are transferred to PC.
For details on transferring, refer to the help of
Everio MediaBrowser in the CD-ROM.
To quit the screen
1) Select [DONE].
2) Select [YES].
To confirm the export setting
Press EXPORT on the index screen.
Preparation:
Select ! mode.
•
Select the recording mode.
•
Transferring the Files to PC
Press EXPORT twice.
Preparation:
Install iTunes® on a PC.
1 Connect the camcorder to the PC
with the USB cable.
2 Select [EXPORT TO LIBRARY].
To turn off the export mode
Press EXPORT twice.
Making the Export Setting
You can set the recorded videos to be
exported to iTunes®.
Preparation:
Select ! mode.
•
Select the playback mode.
•
1 Press EXPORT.
All the files with the export setting turned
on are transferred to PC.
If you cannot export the file to iTunes®
Refer to “Q&A”, “Latest Information”,
“Download Information”, etc. in [Click for
Latest Product Info] in the help of the
provided Everio MediaBrowser software.
2 Select the file and select [
].
To check the content of the file, select
[CHECK].
3 Select [DONE].
ꢁꢂ EN
Uploading Files to Websites
Turning on the Upload Mode
Uploading Files
You can upload the file to video sharing
websites (YouTube™) easily after recording.
For details on uploading files, refer to the help
of Everio MediaBrowser in the CD-ROM.
Preparation:
1 Connect the camcorder to the PC
Select ! mode.
•
with the USB cable.
Select the recording mode.
•
2 Select [UPLOAD].
Press UPLOAD twice.
If you record a file with the upload mode
set on, the recording stops automatically
10 minutes after the recording is started.
The remaining time is displayed on the LCD
monitor.
If you cannot upload the file to
YouTube™
You need your YouTube™ account to
upload files to YouTube™. Create your
account.
•
Refer to “Q&A”, “Latest Information”,
•
NOTE
“Download Information”, etc. in [Click for
Latest Product Info] in the help of the
provided Everio MediaBrowser software.
The upload mode turns off each time recording
is finished.
Customer Support Information
Use of this software is authorized according to the terms of the software license.
JVC
When contacting the nearest JVC office or agency in your country (refer to the JVC Worldwide Service
following information ready.
Product Name, Model, Problem, Error Message
PC (Manufacturer, Model (Desktop/Laptop), CPU, OS, Memory (MB), Available Hard Disk Space (GB))
•
•
Please note that it may take some time to respond to your questions, depending on their subject matter.
JVC cannot answer questions regarding basic operation of your PC, or questions regarding specifications
or performance of the OS, other applications or drivers.
Pixela
Region
Language
Phone #
USA and Canada
English
+1-800-458-4029 (toll-free)
Europe (UK, Germany, France,
and Spain)
English/German/French/Spanish
+800-1532-4865 (toll-free)
+44-1489-564-764
English/German/French/Spanish/
Italian/Dutch
Other Countries in Europe
Asia (Philippines)
China
English
+63-2-438-0090
Chinese
10800-163-0014 (toll-free)
Please check our website for latest information and downloading.
EN ꢁꢃ
FURTHER INFORMATION
Changing the Menu Settings
To return to the previous screen
Select @.
1 Touch MENU.
To quit the screen
Select [QUIT].
2 Select the desired menu.
3 Select the desired setting.
Troubleshooting
Before requesting service, consult the following chart. If the solutions indicated in the chart do not
solve the problem, consult your nearest JVC dealer or JVC service center for instructions.
Refer also to the FAQ of new products on JVC’s website.
The following phenomena are not malfunctions.
The camcorder heats up when it is used for a long time.
The battery heats up during charging.
When playing back a video, the image stops momentarily or the sound is interrupted at junctions
between scenes.
•
•
•
LCD monitor momentarily become red or black when sunlight is recorded.
Black spots, or red, green, or blue spots appear on the LCD monitor.
(The LCD monitor contains 99.99% effective pixels, but 0.01% or fewer pixels may be ineffective.)
•
•
Trouble
Action
Connect the AC adapter correctly.
•
•
Recharge the battery pack.
No power is supplied.
[QUICK RESTART] is set to [ON].
The battery is being charged.
•
•
The power/charge lamp
blinks when the LCD
monitor is closed.
Fully charge the battery pack, run it down, and then recharge it
again.
If the camcorder is used for long periods of time in high or low
temperatures, or if the battery pack is repeatedly charged, the
amount of remaining battery may not be displayed correctly.
•
The remaining battery
display is not correct.
•
The LCD monitor may be difficult to see if used in bright areas
such as under direct sunlight.
The LCD monitor is
difficult to see.
•
ꢁꢄ EN
Trouble
Action
Slide the mode switch to select the desired mode (! or #).
•
•
Recording cannot be
performed.
Such phenomenon occurs when shooting a subject illuminated by
bright light. This is not a malfunction.
Vertical lines appear on
recorded images.
Sometimes playback is interrupted at the connecting section
between two scenes. This is not a malfunction.
Sound or video are
interrupted.
•
•
Select [PLAYBACK OTHER FILE] then search the video on
the index screen. (Video files that have damaged management
information can be played back.)
Cancel group display and date search functions.
Change the setting in [REC MEDIA FOR VIDEO] or [REC MEDIA
FOR IMAGE]. (Files on other media are not displayed.)
Cannot find a recorded
video.
•
•
If there are many files (such as video) in the camcorder, it takes
time for the camcorder to respond. It is recommended that you
copy all files from the camcorder onto your computer, and erase
the files from the camcorder.
The camcorder operates
slowly when switching
between video mode
and still image mode,
or when switching the
power on or off.
•
Check the remaining battery pack charge.
•
•
(When the battery pack is fully charged, the lamp does not flash.)
When recharging in either a hot or cold environment, ensure that
battery is being charged within the permitted temperature range.
(If the battery pack is being recharged outside the permitted
temperature range, recharging may stop to protect the battery
pack.)
The lamp does not flash
during battery pack
charging.
Replace the battery.
Set [REMOTE] to [ON].
The remote control may not operate outdoors or in places
exposed to strong light.
•
•
•
The remote control does
not work.
You need your YouTube™ account to upload files to YouTube™.
Create your account.
Refer to “Q&A”, “Latest Information”, “Download Information”, etc.
in [Click for Latest Product Info] in the help of the provided Everio
MediaBrowser software.
•
•
Cannot upload the file to
YouTube™.
Refer to “Q&A”, “Latest Information”, “Download Information”, etc.
in [Click for Latest Product Info] in the help of the provided Everio
MediaBrowser software.
•
Cannot export the file to
iTunes®.
If a malfunction occurs in the built-in memory
!ꢀꢀPerform [FORMAT BUILT-IN MEM.]. (All data is deleted.)
#ꢀIf this does not solve the problem, contact the JVC customer service for repairs.
To reset the camcorder when it does not operate normally
!ꢀClose the LCD monitor and remove the power supply (battery pack or AC adapter) from the
camcorder, then reattach it.
#ꢀExecute [FACTORY PRESET].
EN ꢁꢅ
Warning Indications
Indication
Action
Set the clock. If the message still appears after setting the
clock, the battery for the clock has been depleted. Consult your
nearest JVC dealer.
•
SET DATE/TIME!
Be sure to use JVC battery packs.
COMMUNICATING ERROR
•
Set [REC MEDIA FOR VIDEO] to [BUILT-IN MEMORY].
Replace the SD card. (Files recorded with other devices that
support AVCHD cannot be played back on this camcorder.)
•
•
CANNOT USE IN
VIDEO MODE
Select [OK] and select [YES] to perform formatting.
NOT FORMATTED
•
Check the operating procedure, and perform once again.
Turn off the camcorder, and turn it on again.
FORMAT ERROR!
•
•
DATA DELETION ERROR
Perform formatting. (All data is deleted.)
Turn off the camcorder, and turn it on again.
•
•
ERROR IN BUILT-IN
MEMORY!
Perform formatting. (All data is deleted.)
Remove and re-insert the SD card. (MultiMediaCard cannot be
used.)
•
•
Remove any dirt from the SD card terminals.
Insert the SD card before switching the power on.
Turn off the camcorder, and turn it on again.
Do not change the folder name on a computer.
MEMORY CARD ERROR!
•
•
•
•
Turn off the camcorder and turn it on again.
Prevent the camcorder from vibration and shock.
•
•
RECORDING CANCELLED
RECORDING FAILURE
SD card:
Remove and re-insert the SD card. (MultiMediaCard cannot be
used.)
•
Remove any dirt from the SD card terminals.
Insert the SD card before switching the power on.
Built-in memory:
•
•
PLAYBACK FAILED
Do not allow the camcorder to be subject to impact/vibrations.
•
Delete files. Move files to a PC or other devices.
Replace the SD card with a new one.
•
INSUFFICIENT SPACE
•
Select [OK] to restore.
VIDEO MANAGEMENT FILE IS
DAMAGED, RECOVERY IS
REQUIRED TO RECORD/PLAYBACK,
RECOVER?
•
ꢁꢆ EN
Specifications
General
Power supply
AC Adapter
Power requirement
DC 11 V (Using AC adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 4.0 W*
* When the monitor backlight is set to
[STANDARD] mode.
AC 110 V to 240 V , 50 Hz/60 Hz
$
Output
DC 11 V
, 1 A
§
Remote Control
Power supply
Rated Current Consumption: 1A
Dimensions (W x H x D)
67 mm x 72 mm x 135 mm
(2-11/16" x 2-7/8" x 5-3/8")
Weight
Approx. 400 g (0.89 lbs)
Approx. 485 g (1.07 lbs) (incl. battery pack)
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
–20°C to 50°C (–4°F to 122°F)
Operating humidity
DC 3 V
Battery life
Approx. 1 year
(depending on the frequency of use)
Operating distance
Within 4 m (13.16 ft)
Operating temperature
0°C to 40°C (32°F to 104°F)
Dimensions (W x H x D)
42 mm x 14.5 mm x 91 mm
(1-11/16" x 5/8" x 3-5/8")
Weight
35% to 80%
Approx. 30 g (0.07 lbs)
(incl. battery)
Camera/LCD monitor
Pickup
1/2.33" (10,290,000 pixels) progressive CMOS
Lens
Still image
Format
JPEG
F 2.8 to 4.5, f = 6.7 mm to 67.0 mm,
10:1 power zoom lens
Filter diameter
ø46 mm
LCD monitor
2.8" diagonally measured,
LCD panel/TFT active matrix system
Flash
Within 2 m (6.6 ft)
(recommended shooting distance)
Image size
4:3 mode:
3456 x 2592 / 3072 x 2304 /
2592 x 1944 / 1600 x 1200 /
640 x 480
16:9 mode: 3456 x 1944 / 3072 x 1728 /
2592 x 1456 / 1920 x 1080 /
1280 x 720
Image quality
FINE / STANDARD
Video
Connectors
Signal format
1080/60i
AV output
Video output: 1.0 V (p-p), 75
Audio output: 300 mV (rms), 1 k
HDMI
HDMI™ (V.1.3 with x.v.Color™)
Component output
Y, Pb, Pr component output
Y: 1.0 V (p-p), 75
Pb/Pr: 700 mV (p-p), 75
W
Recording/Playback format
Video:
Audio:
W
MPEG-4 AVC/H.264
Dolby Digital (2ch)
Recording mode (video)
UXP:
XP:
SP:
VBR, average of 24 Mbps
W
VBR, average of 17 Mbps
VBR, average of 12 Mbps
VBR, average of 5 Mbps
W
USB
EP:
Mini USB type A and type B,
USB 2.0 compliant
Headphones
Recording mode (audio)
48 kHz, 256 kbps
ø3.5 mm mini-jack, stereo, analog output
Microphone
ø3.5 mm mini-jack, stereo, analog input
Design and specifications subject to change
without notice.
EN ꢁꢇ
Specifications (Continued)
h: hour/m: minute
Approximate recordable time (for video)
Recording medium
Built-in Memory
32 GB
SDHC Card
8 GB 16 GB
4 GB
20 m
32 GB
2 h 40 m
4 h 00 m
5 h 52 m
14 h 40 m
Quality
UXP
2 h 56 m
4 h 9 m
40 m
1 h 20 m
2 h 00 m
2 h 56 m
7 h 20 m
XP
SP
EP
30 m
1 h 00 m
1 h 28 m
3 h 40 m
5 h 53 m
14 h 44 m
44 m
1 h 50 m
Approximate number of images (for still image)
Recording medium
Built-in
Memory
SD Card
SDHC Card
32 GB 512 MB 1 GB
2 GB
640
4 GB
8 GB 16 GB 32 GB
Image size/Quality
3456 x 1944 / FINE
9999
9999
9999
9999
9999
9999
9999
9999
9999
9999
7730
9999
9760
9999
9999
9999
9999
9999
9999
9999
160
250
200
320
280
440
510
810
320
500
400
640
570
890
1270 2570 5180 9999
3456 x 1944 / STANDARD
3072 x 1728 / FINE
1030 2030 4090 8260 9999
820 1620 3260 6590 9999
3072 x 1728 / STANDARD
2592 x 1456 / FINE
1290 2550 5140 9999 9999
1150 2260 4560 9200 9999
1790 3530 7100 9999 9999
2592 x 1456 / STANDARD
1920 x 1080 / FINE
1030 2100 4140 8330 9999 9999
1620 3210 6310 9999 9999 9999
1920 x 1080 / STANDARD
1280 x 720 / FINE
1190 2400 4690 9230 9999 9999 9999
1760 3530 6780 9999 9999 9999 9999
1280 x 720 / STANDARD
3456 x 2592 / FINE
120
190
150
240
210
340
550
880
240
380
300
480
420
680
480
770
610
980
870
960
1930 3860 7810
3456 x 2592 / STANDARD
3072 x 2304 / FINE
1510 3050 6110 9999
1210 2440 4880 9860
1930 3890 7790 9999
1710 3450 6900 9999
STANDARD
3072 x 2304 /
FINE
2592 x 1944 /
2592 x 1944 / STANDARD
1600 x 1200 / FINE
1380 2720 5490 9999 9999
1110 2260 4440 8950 9999 9999
1760 3590 7060 9999 9999 9999
1600 x 1200 / STANDARD
640 x 480 / FINE
3330 6670 9999 9999 9999 9999 9999
5990 9999 9999 9999 9999 9999 9999
640 x 480 / STANDARD
The recordable time and the number of still images are approximate and may differ depending on the
recording environment, the condition of the built-in memory or the SD card, or the remaining battery
power.
ꢂ0 EN
h: hour/m: minute
Required charging/recording time (approx.)
Battery pack
BN-VF808U
Charging time
Recording time
1 h 50 m
2 h 40 m
3 h 40 m
1 h 10 m*
2 h 25 m*
3 h 40 m*
BN-VF815U
(Provided)
BN-VF823U
* When the monitor backlight is set to [STANDARD] mode.
EN ꢂ1
Cautions
ATTENTION:
AC Adapter
The product you have purchased is
powered by a rechargeable battery
that is recyclable.
Please call 1-800-8-BATTERY for
information on how to recycle this
battery.
When using the AC adapter in areas other than
the USA
The provided AC adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to
an AC wall outlet other than American National
Standard C73 series type use an AC plug adapter,
called a “Siemens Plug”, as shown.
Recording Medium
Be sure to follow the guidelines below
to prevent corruption or damage to your
recorded data.
•
For this AC plug adapter, consult your nearest
JVC dealer.
Do not bend or drop the recording medium,
Plug Adapter
•
or subject it to strong pressure, jolts or
vibrations.
Do not splash the recording medium with water.
•
Do not use, replace, or store the recording
•
medium in locations that are exposed to
strong static electricity or electrical noise.
Do not turn off the camcorder power or
•
Battery Pack
remove the battery or AC adapter during
shooting, playback, or when otherwise
accessing the recording medium.
The supplied battery pack is a Terminals
lithium-ion battery. Before using
the supplied battery pack or an
optional battery pack, be sure
Do not bring the recording medium near
•
objects that have a strong magnetic field or
that emit strong electromagnetic waves.
to read the following cautions:
Do not store the recording medium in locations
•
with high temperature or high humidity.
Do not touch the metal parts.
•
When formatting or erasing data using
the camcorder, only the file administration
information is changed. The data is not
completely erased from the hard disk. If you
want to completely erase all of the data,
we recommend either using commercially
available software that is specially designed for
that purpose, or by physically destroying the
camcorder with a hammer etc.
•
•
To avoid hazards
... do not burn.
•
... do not short-circuit the terminals. Keep it away
from metallic objects when not in use. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery cap
is misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
... do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
... use only specified chargers.
LCD Monitor
To prevent damage to the LCD monitor, DO
NOT
To prevent damage and prolong service life
•
... do not subject to unnecessary shock.
... charge within the temperature range of 10°C
to 35°C (50°F to 95°F). Cooler temperatures
require longer charging time, or in some cases
stop charging at all.
... push it strongly or apply any shocks.
... place the camcorder with LCD monitor on the
bottom.
To prolong service life
•
... avoid rubbing it with coarse cloth.
Warmer temperatures prevent complete
charging, or in some cases stop charging at all.
... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
... fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period of time.
... remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
ꢂꢀ EN
To prevent the unit from dropping,
•
Main Unit
Fasten the grip belt securely.
•
When using the camcorder with a tripod,
•
For safety, DO NOT
•
attach the camcorder to the tripod securely.
If the camcorder drops, you may be injured and
the camcorder may be damaged.
... open the camcorder’s chassis.
... disassemble or modify the unit.
... allow inflammables, water or metallic objects to
enter the unit.
When a child uses the unit, there must be
parental guidance.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
... place naked flame sources, such as lighted
candles, on the apparatus.
... expose the apparatus to dripping or splashing.
... leave dust or metal objects adhered to the
power plug or an AC wall outlet.
... insert any objects in the camcorder.
Avoid using the unit
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or vibration.
... near a television set.
Declaration of Conformity
Model Number : GZ-HM400U
Trade Name : JVC
Responsible party : JVC AMERICAS CORP.
Address : 1700 Valley Road Wayne, N. J. 07470
Telephone Number : 973-317-5000
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
•
Changes or modifications not approved by
JVC could void the user’s authority to operate
the equipment.This equipment has been
tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of
the FCC Rules.These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures: Reorient or relocate
the receiving antenna. Increase the separation
between the equipment and receiver.
... near appliances generating strong magnetic
or electric fields (speakers, broadcasting
antennas, etc.).
... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
DO NOT leave the unit
•
... in places of over 50°C (122°F).
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
... in high places such as on a TV. Leaving the unit
in high places while a cable is connected may
result in a malfunction if the cable is caught and
the unit falls onto the floor.
To protect the unit, DO NOT
•
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright
objects for long periods.
... expose the lens to direct sunlight.
... swing it excessively when using the hand strap.
... swing the soft camcorder case excessively
when the camcorder is inside it.
... place the camcorder in dusty or sandy areas,
such as on a beach.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/
TV technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
EN ꢂꢁ
Terms
A
O
AC Adapter ..................................................16, 42
Number of Images .............................................40
AV Connection .............................................25, 28
B
C
On-screen Recording Control ............................19
On-screen Zoom Control ...................................21
Battery Pack ................................................16, 42
BD/DVD Backup ................................................26
BD/DVD Burner .................................................26
P
Playback Zoom ............................................22, 23
CD-ROM ......................................................10, 29
Clock Adjust ......................................................16
Component Connection ....................................24
Copying Files .....................................................26
Q
R
Quick Review ...............................................19, 20
Recording Medium ............................................42
Remaining Battery Power ..................................21
Remaining Recording Time ...............................21
Remote Control ...........................................11, 13
D
Date/Time Setting ...............................................5
Digest Playback .................................................22
Dubbing Playback ..............................................28
E
F
H
I
S
U
Export to Library Mode ......................................34
Flash .................................................................21
HDMI .................................................................24
iTunes ................................................................34
Speaker Volume ................................................22
Uploading Files .................................................35
USB Cable ...................................................26, 30
Y
Z
Viewing Files on TV ...........................................24
YouTube .............................................................35
Zoom .................................................................21
L
Language Setting ..............................................17
LCD Monitor ................................................14, 42
M
Menu Settings ...................................................36
US
© 2009 Victor Company of Japan, Limited
0609FOH-AL-VM
EN
Advanced INSTRUCTIONS
HD MEMORY CAMERA
GZ-HM400
Using a USB External Hard Disk Drive......... 73
Upload Trimming........................................... 75
via HDMI .................................................... 76
JVC Software License Agreement ............ 92
Playback with Special Effects....................... 53
File Search Function..................................... 54
Playing Back MTS Files................................ 55
Print Setting ................................................ 67
DPOF Print Setting....................................... 67
Direct Printing with PictBridge Printer .......... 68
46 EN
RECORDING/PLAYBACK
Manual Recording
Manual recording mode enables you to set the
focus and screen brightness, etc. manually.
Brightness
You can adjust the brightness manually.
Changing to Manual Recording Mode
Preparation:
1 Slide the FOCUS/BRIGHT switch up
to BRIGHT.
Select ! or # mode.
•
Select the recording mode.
•
Select [A/M] twice.
2 Turn the adjustment dial to adjust the
brightness of the subject.
The brightness is corrected in the following
range.
To return to the auto recording mode
Select [A/M] so that the @ indicator
appears.
! mode: –6 to +6 by 1.
# mode: –2.0 to +2.0 (EV) by 1/3 EV.
3 Press SET.
Focusing
Shutter Speed
You can adjust the focus manually.
A fast shutter speed can freeze the motion
of the fast-moving subject, and a slow
shutter speed can blur the subject to give the
impression of motion.
1 Slide the FOCUS/BRIGHT switch
down to FOCUS.
1 Press S (Shutter Speed).
2 Turn the adjustment dial to focus on
the subject.
@ (long-distance side)
2 Turn the adjustment dial to adjust the
? (short-distance side)
shutter speed in the following range.
The smaller the value, the faster the shutter
speed.
3 Press SET.
! mode: 1/2 to 1/4000
# mode: 1/2 to 1/500*
NOTE
* 1/2 to 1/250 when using the flash
When zooming, the subject will not go out of
focus if you adjust the focus at the telephoto
(T) side before zooming to the wide angle (W)
side.
3 Press SET.
NOTE
It is recommended to use a tripod when
recording with a slow shutter speed.
EN 47
Manual Recording (Continued)
3 Select the desired function.
Aperture Priority Setting
You can select one of the following
functions. For details on each function, see
the pages given.
You can add a blurring effect to the
background by setting the aperture value
(F-number).
[ ] = default setting
[BACKLIGHT COMP.] (Z p. 50)
SCENE SELECT (Z p. 49)
PHOTOMETRY AREA (Z p. 50)
WB (Z p. 50)
•
1 Press A (Aperture Priority Setting).
•
•
•
FOCUS ASSIST (Z p. 49)
•
HIGH SPEED RECORDING*1 (Z p. 51)
•
SHUTTER MODE (Z p. 78)
•
2 Turn the adjustment dial to select one
CONT. SHOOTING SPEED (Z p. 82)
•
FLASH*2 (Z p. 21)
of the following aperture value.
•
SELF-TIMER*2 (Z p. 77)
At the lower F-number (larger aperture
value), the background will be more
blurred. At the higher F-number (smaller
aperture value), the focus will be clearer for
both near and far objects.
F2.8 / F3.4 / F4.0 / F5.6
F4.5 when the zoom lever is set all the way
to T side.
•
*1 ! mode only
*2 # mode only
To make adjustment by the USER button
Operate as follows.
3 Press SET.
In the case of functions that are turned
on or off ([BACKLIGHT COMP.], etc.)
Pressing U (USER) turns on or off the
function.
NOTE
If the image is too bright, select a larger
F-number. If the image is too dark, select a
smaller F-number.
In the case of functions that
have settings to be selected
([SCENE SELECT], etc.)
1) Press U (USER).
Manual Setting by the USER button
2) Turn the adjustment dial to adjust or
select a setting.
3) Press SET.
By assigning one of manual adjustment
functions that you frequently use to the
U (USER) button, you can access the function
quickly.
4) Press U (USER) again to quit the screen.
To assign a function to the USER button
1 Touch MENU.
2 Select [USER BUTTON SETTING].
48 EN
4 Select the desired setting.
Manual Setting in Menu
In the manual recording mode:
1 Touch MENU.
2 Select [MANUAL SETTING].
Depending on the kind of settings you
select, you can set the value by using the
touch sensor.
To return to the previous screen
Select
.
@
To quit the screen
Select [QUIT].
3 Select the desired menu.
Menus
Settings: [ ] = Factory-preset
1 [OFF]: Deactivates the function.
! PORTRAIT: The subject in the foreground is accentuated by
blurring the background.
> LANDSCAPE: Focuses on the distant landmarks.
$ TWILIGHT: Makes evening scenes look more natural.
NIGHT: Records with more sensitivity in dim locations by
adjusting the shutter speed automatically.
5
? SNOW: Compensates for subjects that may appear too dark
when shooting in extremely bright surroundings, such as
in snow.
( BEACH: Captures vividly the blue sky and sea on a sunny
beach without making the people appear dark.
) SPORTS: Records fast moving subjects clearly.
. SPOTLIGHT: Select this when a spotlight makes a subject
appear too bright.
SCENE SELECT
Adjusts the exposure and/or
shutter speed to suit your
surroundings or the subject.
+ FIREWORKS: Suitable for shooting fireworks in the night
sky.
/ SUNSET: Captures the atmosphere of the sunset in
beautiful colors.
The image becomes black and white. The outline of focused
object is displayed in blue.
Use this for adjusting the focus more precisely.
Adjust the focus, then select [SET] to fix the focus.
FOCUS ASSIST
Assists you to adjust the
focus.
EN 49
Manual Recording (Continued)
Menus
Settings: [ ] = Factory-preset
@ [AUTO]: White balance is adjusted automatically.
B MWB: Adjusts the white balance manually depending on
the light source.
1) Hold a sheet of plain white paper in front of
the camcorder so that the white paper fills
the screen.
WB
=
Adjusts the white balance to
achieve the optimum colors
for the amount of light in your
surroundings during recording.
2) Keep touching OK until the B indicator
appears.
D FINE: When shooting outdoors on a sunny day.
E CLOUD: When shooting outdoors on a cloudy day.
F HALOGEN: When a video light or similar type of lighting is
used.
- BACKLIGHT COMP.
Backlight compensation
brightens the subject by
increasing the exposure.
1 [OFF]: Deactivates the function.
0 ON: Activates the function.
PHOTOMETRY AREA
Enables you to adjust the
brightness in the desired spot
when backlight compensation
does not work well.
[WHOLE SCREEN]: Brightness is adjusted automatically
for whole screen.
SPOT: Brightness for the specified spot is adjusted
6
7
automatically.
1 [OFF]: No effect is used.
J SEPIA: The image has a brownish tint like old still images.
K MONOTONE: The image becomes black and white like old
movies.
w EFFECT
Enables you to record videos or
still images with special effects.
L CLASSIC FILM*: This effect skips frames to give images of
an old movie atmosphere.
M STROBE*: The image looks like a series of consecutive
snapshots.
* ! mode only
1 [OFF]: Deactivates the function.
0 ON: Activates the function.
t TELE MACRO
Enables you to shoot a
subject as large as possible
at a distance of approx. 60 cm
(1.97 ft).
NOTE
Set [TELE MACRO] to [OFF] if you will not take close-up still
images.
Non-close-up still images will be blurred if [TELE MACRO] is set to
[ON].
50 EN
Menus
Settings: [ ] = Factory-preset
1 [OFF]: Deactivates the function.
70%: Sections that are close to be over-exposed are
displayed in striped pattern.
ZEBRA
>
The over-exposed sections of
the subject are displayed in
striped pattern on the screen.
Use this as a guide for adjusting
the brightness.
100%: Sections that are over-exposed are displayed in
striped pattern.
NOTE
(In ! mode only)
Correct the brightness by using the shutter speed or aperture
priority setting function.
Adjust the sharpness using the touch sensor, then touch OK.
SHARPNESS
^
Enhances the outline of the
subject.
NOTE
Enhancing the sharpness causes the recorded image to appear
grainy.
(In ! mode only)
High Speed Recording
4 Press START/STOP to start recording.
Recording ends automatically when the
You can capture fast-moving subjects clearly.
recording time limit is expired, even if you do
not stop recording.
Preparation:
Select ! mode.
•
Select the recording mode.
•
NOTE
Video quality is fixed to XP mode.
Sound cannot be recorded.
Face detection cannot be set.
Only optical zoom is available.
When using the U (USER) button, pressing
the U (USER) button repeatedly changes the
setting.
1 Touch MENU.
•
•
•
•
•
2 Select [HIGH SPEED RECORDING].
3 Select the desired recording speed.
See the table below.
Recording time
(sec)
Playback time
Aspect ratio
(sec)
Setting
Image size
Deactivates the function.
1 [OFF]
120fps
300fps
600fps
480 x 270
480 x 116
640 x 72
4
4
8
16:9
20
24
16:3.9
16:1.8
2.4
fps = frames per second
EN 51
Advanced Recording Functions
Select
.
Registering Files to Events
If you select an event to register the file to
before starting recording, you can find the file
easily at playback.
Preparation:
Select ! mode.
•
To turn off the face detection mode
Select again.
Select the recording mode.
•
1 Touch MENU.
Recording still images with the face
detection mode turned on
2 Select [REGISTER EVENT].
1) Press and hold SNAPSHOT half way.
3 Select the event.
2) Press SNAPSHOT.
Using the self-timer in the face detection mode
Preparation:
Set [SELF-TIMER] to [FACE DETECTION].
1) Press SNAPSHOT.
Faces are detected.
The selected event is displayed on the
screen.
To quit the screen
Select [QUIT].
To search by event
See page 55.
2) The still image is recorded 3 seconds after
the face of the photographer is detected.
NOTE
Once you select a certain event to register a
file, the setting will remain even if you turn off
the camcorder.
Photographer
Turning on the Face Detection Mode
If you set this mode on, the camcorder detects
the faces and adjust brightness and focus
so that the faces are recorded clearly. The
maximum of 16 face frames are displayed.
NOTE
If the LCD monitor is turned upside down,
not displayed. Change the setting when the LCD
monitor is in the normal position.
You cannot turn on the face detection mode if
[SELF-TIMER] is set to [FACE DETECTION].
(This is indicated by blinking .)
Depending on the condition, faces may not be
detected.
is
•
•
Preparation:
Select ! or # mode.
•
Select the recording mode.
•
•
•
If the face detection does not work correctly, turn
off the mode before recording.
52 EN
Advanced Playback Functions
Items for WIPE/FADER setting
Playback with Special Effects
O FADER-WHITE:
•
•
•
Fades in or out with a white screen.
P FADER-BLACK:
Wipe or fader effects
Fades in or out with a black screen.
T WIPE-SLIDE:
Add effects at the beginning and end of videos.
These effects cannot be set for still images.
Wipes in from right to left, or wipes out in
the opposite way.
Preparation:
U WIPE-DOOR:
•
Select ! mode.
•
Wipes in as the two halves of a black
screen which open to the left and right
revealing the scene, or wipes out in the
opposite way.
Select the playback mode.
•
1 Touch MENU.
V WIPE-SCROLL:
•
•
2 Select [WIPE/FADER].
Wipes in from the bottom to the top of a
black screen, or wipes out in the opposite
way.
W WIPE-SHUTTER:
Wipes in from the center of a black screen
toward the top and bottom, or wipes out in
the opposite way.
3 Select a desired effect.
NOTE
For details on each effect, see the right
column.
No effect will be applied on files with a play
time shorter than 7 seconds.
Original sound reproduction
The K2 function is designed to provide natural
sound by improving the playback sound from
low bit-rate digital sources.
4 Select the file you want to play back.
1 Press MENU.
To quit the screen
Touch MENU.
2 Select [K2 TECHNOLOGY].
To turn off the effect
Select [OFF] in step 3.
3 Select [ON].
To quit the screen
Touch MENU.
To turn off the effect
Select [OFF] in step 3.
EN 53
Advanced Playback Functions (Continued)
Date Index Screen
File Search Function
You can search the desired file by the
recording date.
Preparation:
Select ! or # mode.
•
Select the playback mode.
•
1 Select
.
In case of # mode, go to step 3.
Group Index Screen
!
You can search the desired file by the group.
The group is created automatically based on
recording date and time. And the contents of
the group are changed when adding/deleting
or editing scenes.
2 Select [SEARCH DATE].
1 Select
.
3 Select the recording date.
2 Select [GROUP].
4 Select the file you want to play back.
3 Select the file you want to play back.
The number of files in the group is
displayed in the thumbnails.
To return to the index screen
Select
.
@
To return to the index screen
To quit the screen
Select [QUIT].
Select
.
@
To quit the screen
Select [QUIT].
NOTE
The contents of the group may be changed
•
depending on the interval of the recording
time. To change the contents, register the
event. (Z p. 52)
The created groups may not be listed by
recording date such as when copying the
files to an SD card.
•
54 EN
Event Screen
!
Playing Back MTS Files
You can search the desired file by the event
that you registered the file to when recording.
(Z p. 52) After searching by the event, you can
search by the recording date to narrow down
the search.
MTS files (demonstration files, etc.) are stored
in the EXTMOV folder.
Follow the procedure below to play back the
MTS files in the EXTMOV folder.
Preparation:
1 Select
.
Select ! mode.
•
Select the playback mode.
•
2 Select [SEARCH EVENT].
1 Touch MENU.
2 Select [PLAYBACK OTHER FILE].
3 Select the event.
3 Select the file you want to play back.
4 Select the recording date.
To display all the files, select [ALL].
To return to the normal file playback
mode
Select
.
@
NOTE
An MTS file is created in the EXTMOV folder
when management information is corrupted.
5 Select the file you want to play back.
To return to the index screen
Select
.
@
To quit the screen
Select [QUIT].
To change the event registration of a file
See page 60.
EN 55
EDITING
Managing Files
CAUTION
Deleting Files
Do not remove the recording medium or
perform any other operation (such as turning
off the power) while accessing files. Also,
be sure to use the provided AC adapter, as
the data on the recording medium may be
corrupted if the battery becomes exhausted
during operation. If the data on the recording
medium becomes corrupted, format the
recording medium to use the medium again.
(Z p. 85)
Protected files cannot be deleted. To delete
them, release the protection first. (Z p. 58)
Once files are deleted, they cannot be
restored. Check files before deleting.
•
•
Preparation:
Select ! or # mode.
•
Select the playback mode.
•
1 Touch MENU.
Capturing a Still Image from a Video
2 Select [DELETE].
You can capture the desired scene from a
recorded video, and store it as a still image.
Preparation:
Select ! mode.
•
Select the playback mode.
•
Press SNAPSHOT when playback is
paused.
Deleting the Currently Displayed File
After performing steps 1-2
3 Select [CURRENT].
NOTE
Captured still images are stored at a
•
resolution of 1920 x 1080. The image can
be elongated in the horizontal or vertical
directions depending on the quality of the
source video file.
4 Select [YES].
The continuous shooting function cannot be
used to capture images.
•
You cannot capture video during playback.
•
You can select the previous or next file by
selecting
or
.
%
&
To quit the screen
Select [QUIT].
56 EN
Deleting Selected Files
Deleting All Files
After performing steps 1-2 (Z p. 56)
After performing steps 1-2 (Z p. 56)
3 Select [FILE SELECT].
3 Select [DELETE ALL].
4 Select the desired file and select $.
4 Select [YES].
The $ mark appears on the file. To select
other files, repeat this step.
To check the content of the file, select
[CHECK].
•
•
To quit the screen
Select [QUIT].
5 Select [EXEC].
Protecting Files
Preparation:
6 Select [YES].
Select ! or # mode.
•
Select the playback mode.
•
1 Touch MENU.
2 Select [EDIT].
To quit the screen
Select [QUIT].
3 Select [PROTECT/CANCEL].
EN 57
Managing Files (Continued)
7 Select [YES].
Protecting the Currently Displayed File
After performing steps 1-3 (Z p. 57)
4 Select [CURRENT].
To release protection
Select the protected file in step 5.
Protecting All Files
5 Select [YES].
After performing steps 1-3 (Z p. 57)
4 Select [PROTECT ALL].
You can select the previous or next file by
selecting % or &.
To quit the screen
Select [QUIT].
5 Select [YES].
Protecting Selected Files
After performing steps 1-3 (Z p. 57)
4 Select [FILE SELECT].
To quit the screen
Select [QUIT].
To release protection of all files
1) In step 4, select [CANCEL ALL].
2) Select [YES].
5 Select the desired file and select x.
The x (protection) mark appears on the
file. To select other files, repeat this step.
To check the content of the file, select
[CHECK].
•
•
6 Select [QUIT].
58 EN
Viewing File Information
Preparation:
! mode:
Pause the playback. Otherwise, select the file
on the index screen.
D
(Dim)
B
Brightness level
(Bright)
# mode:
Play back the still image. Otherwise, select the
file on the index screen.
The shutter speed, F-number and ISO
sensitivity (GAIN) when recorded are also
displayed.
A larger number of pixels in the center
position indicates correct exposure and
well-balanced brightness.
•
•
Press INFO.
To turn off the file information display
Press INFO again.
FILE (# mode):
•
•
•
•
•
•
•
File name
NOTE
FOLDER (# mode):
The shutter speed displayed during shooting
in auto mode is an approximation. It may not
match the one displayed with the histogram.
Folder name
DATE/TIME:
Date and time of the recording
PB TIME (! mode):
Playback time (length of the file)
SIZE (# mode):
Image size (Z p. 79)
QUALITY:
Video quality/Image quality (Z p. 78, 79)
PROTECT:
File protection status (Z p. 57)
To turn off the file information display
Press INFO again.
Histogram
#
A histogram is a graph indicating the image’s
brightness. By checking the image and its
histogram, you can see the exposure level
pattern and the overall tone reproduction.
Preparation:
Play back the still image.
Press INFO twice.
EN 59
Managing Files (Continued)
6 Select a new event.
Changing the Event Registration
To cancel the event registration, select
[CANCEL].
Preparation:
Select ! mode.
•
Select the playback mode.
•
1 Touch MENU.
2 Select [EDIT].
Changing the Event of the Selected
Files
After performing steps 1-3
4 Select [SET RANGE AND CHANGE].
3 Select [CHANGE EVENT REG.].
5 Select the first file of the range.
Changing the Event of the Currently
Displayed File
After performing steps 1-3
4 Select [CURRENT].
To preview scenes, select the file and
select [CHECK].
6 Select the last file of the range.
7 Select a new event.
To cancel the event registration, select
[CANCEL].
5 Select [YES].
You can select the previous or next file by
selecting
or
.
&
To quit the screen
Select [QUIT].
%
60 EN
6 Select [DIVIDE HERE].
Dividing Files
You can divide a selected video into two.
Preparation:
Select ! mode.
•
Select the playback mode.
•
To set the division point again, select
[CANCEL].
1 Touch MENU.
To quit the screen
Select [QUIT].
2 Select [EDIT].
NOTE
When playing back the divided file, the
recording date of the division point is
displayed.
•
You cannot divide the files with the export
setting or the upload setting turned on.
•
3 Select [DIVIDE].
4 Select the desired file.
Playback starts.
5 Select [SET] at the point you want to
divide the file.
It is recommended to select [SET] after the
pause button is pressed.
Use these controls to locate
the division point.
The actual division point may differ slightly
from the point that is set.
EN 61
Managing Files (Continued)
6 Select [SET] at the end point.
Trimming Files
It is recommended to select [SET] after the
pause button is pressed.
You can select the necessary part of the video
and save it as a new video file.
Preparation:
Select ! mode.
•
Select the playback mode.
•
1 Touch MENU.
To cancel the start point setting, select
[CANCEL].
2 Select [EDIT].
7 Select [CAPTURE TRIMMED FILE].
3 Select [TRIMMING].
To set the start/end point again, select
[REDEFINE AREA].
8 Select [YES].
When copying is finished, the copied file is
added to the index screen.
4 Select the desired file.
9 Touch OK.
To quit the screen
Select [QUIT].
5 Select [SET] at the start point.
It is recommended to select [SET] after the
pause button is pressed.
Use these controls to locate
the starting point.
62 EN
6 Select [SAVE].
Face Detection Zoom
You can enlarge the part including a face in a
still image and save it as a new file.
Preparation:
Select # mode.
•
Zoom images are saved in 16:9 aspect
regardless of the original aspect.
Select the playback mode.
•
1 Select the desired still image.
7 Select [YES].
8 Touch OK.
2 Select
.
3 Touch the touch sensor to select the
face to zoom.
+
4 Select
.
5 Adjust the zoom area.
Touch the touch sensor to move the area
•
upwards or downwards.
+
Select
to change the zoom ratio.
•
EN 63
Playlists
It is a list that enables you to organize
recorded videos in order of preference.
5 Select the file to add to playlist.
Preparation:
Select ! mode.
•
Select the playback mode.
•
To preview scenes, select the file and
select [CHECK].
Creating Playlists
1 Touch MENU.
6 Select the insertion point.
2 Select [EDIT PLAYLIST].
To add other files, repeat steps 5 and 6.
•
To delete a registered scene, select the
•
registered file, then select [CANCEL].
3 Select [NEW LIST].
7 Select [SAVE].
8 Select [SAVE AND QUIT].
4 Select an item and display files.
To quit the screen
Select [QUIT].
To add a picture title after creating a
playlist
See page 66.
[CREATE FROM SCENE]:
Display all files individually.
[CREATE BY GROUP]:
Display all files listed by group.
•
•
NOTE
[CREATE BY DATE]:
Display all the files listed by recording
date.
•
A maximum of 99 playlists can be created.
If you delete the original files, the
corresponding files are also deleted from the
playlist.
•
•
[CREATE BY EVENT]:
•
Search for an event and display the
corresponding files listed by recording
date.
64 EN
Creating Playlists Including Picture
Titles
Playing Back Playlists
You can easily create a playlist including a
picture title.
1 Touch MENU.
2 Select [PLAYBACK PLAYLIST].
1 Press TITLE.
3 Select the playlist.
2 Select the desired picture title.
You can check the picture title in full-screen
by selecting [CHECK].
To stop playback
Select
.
L
To quit the screen
Select [QUIT].
3 Select the desired file.
To play back from the desired scene
1) In step 3, select [CHECK]. (The index
screen for playlist appears.)
2) Select the desired scene.
You can check the scene by selecting
[CHECK].
NOTE
When playing back a playlist with a picture
title, playback starts after the title is displayed
for 5 seconds.
•
4 Select [OK].
When adding a picture title to playlist, the
mark appears on the left side of the file
name.
•
To return to the previous screen
Select
.
@
To quit the screen
Select [QUIT].
EN 65
Playlists (Continued)
Other Operations of Playlists
You can perform additional editing and delete
files in a created playlist.
Adding/Deleting Files in Playlist
After performing steps 1-2 (Z p. 64)
3 Select [EDIT].
4 Select the playlist you want to edit.
To add or delete files, follow the steps 5 to
8. (Z p. 64)
Deleting Playlist
Original files are not deleted even if you delete
the playlist.
After performing steps 1-2 (Z p. 64)
3 Select [DELETE].
4 Select a playlist you want to delete.
To delete all playlists at once, select
[DELETE ALL].
5 When [DELETE PLAYLIST?] appears,
select [YES].
Adding a Picture Title to Playlist
After performing steps 1-2 (Z p. 64)
3 Select [SET TITLE].
4 Select the desired playlist.
5 Select the desired picture title.
66 EN
Print Setting
5 Select the number of prints (max.
DPOF Print Setting
15 prints).
This camcorder is compatible with DPOF
(Digital Print Order Format).You can set which
images to be printed and the number of prints
with this camcorder. This feature is useful to
print with a DPOF-compatible printer or take
the SD card to a photo lab for printing.
Slide your finger up and down on the
sensor.You can set the value by using the
touch sensor.
To set print information for other images,
repeat steps 4 and 5. (You can set up to
999 files.)
•
•
To cancel the selection, set the number of
prints to “00” in step 5.
•
Preparation:
Select # mode.
•
•
•
Select the playback mode.
Set [REC MEDIA FOR IMAGE] to [SD
CARD].
Setting All Files Together (One Print for
Each File)
1 Touch MENU.
After performing steps 1-2
2 Select [EDIT]
[DPOF].
&
3 Select [SET ALL 1].
4 When [SET ALL TO 1?] appears,
Setting Files Individually
select [YES].
After performing steps 1-2
To quit the screen
Select [QUIT].
3 Select [SET PRINT QUANTITY].
To confirm DPOF settings
In step 3, select [CHECK QUANTITY].
If necessary, change the number of prints
for the desired file by following steps 4
and 5. (Z “Setting Files Individually”)
•
To reset DPOF settings
1) In step 3, select [RESET].
2) When [RESET PRINT QUANTITY?]
appears, select [YES].
4 Select the desired file.
To check the content of the file, select
[CHECK].
EN 67
Print Setting (Continued)
1 Press the < (Power) button for
more than 2 seconds to turn on the
camcorder.
Direct Printing with PictBridge Printer
If your printer is compatible with PictBridge,
still images can be printed easily by connecting
the camcorder directly to the printer with the
USB cable.
2 Select [DIRECT PRINT].
Preparation:
Press the < (Power) button for more than
2 seconds to turn off the camcorder.
Power button
DC Connector
3 Select the desired image.
Select a still image using [ ] and [ ],
%
&
USB Connector
then select [SET].
4 Select the desired setting.
AC Adapter
[NUMBER OF PRINTS]:
The number of prints can be set from 1 to
•
USB Cable
99.
[DATE]:
•
Set whether to print the date and time.
To AC Outlet
5 Select [PRINT].
To stop printing after printing starts
1) Select [STOP].
2) When [QUIT PRINTING?] appears, select
[YES].
Printer
USB Connector
68 EN
COPYING
Copying Files
4 Select the direction.
Copying/Moving Files
! mode: [BUILT-IN MEM
CARD]
CARD] or
&
&
You can copy or move files between the built-in
memory and the SD card.
# mode: [BUILT-IN MEM
[CARD
BUILT-IN MEM]
&
! mode
# mode
5 Select the desired menu.
Preparation:
Select ! or # mode.
•
•
•
Select the playback mode.
Make sure that SD card is inserted in the SD
card slot.
Make sure that enough free space is left in
the copy/move destination medium.
•
[COPY ALL] / [MOVE ALL]:
Select this to transfer all files in the
recording medium.
When the size of all files in the built-in
memory is larger than the free space
of the SD card, only the files that can
be contained in the free space will be
transferred.
•
1 Touch MENU.
2 Select [EDIT].
[SELECT AND COPY] / [SELECT AND
MOVE]:
•
Select when you want to transfer the
selected files.
1) Select the desired file. To select other
files, repeat this process.
3 Select [COPY] or [MOVE].
2) Select [EXEC].
6 Select [YES].
[COPY]:
•
Files are copied to the destination
medium while leaving original files in the
source medium.
File transfer starts. When [COPYING
COMPLETED] / [MOVING COMPLETED]
appears, touch OK.
[MOVE]:
•
Files are moved to the destination
medium while deleting original files in the
source medium.
To quit the screen
Select [QUIT].
To stop the file transfer
1) Select [STOP].
2) When [QUIT?] appears, select [YES].
EN 69
Copying Files (Continued)
NOTE
Using a BD/DVD Burner
Refer also to the BD/DVD burner’s instruction
manual.
•
•
•
The files in the camcorder can be backed up to
a disc using a BD/DVD burner.
Use one of the following methods to view
the disc. (If you try to play back the disc with
incompatible player, the disc may not be
ejected.)
- Playing back the disc in the BD/DVD burner
using the camcorder. (Z p. 72)
- Playing back the disc using a BD/DVD
burner.*
When connecting to a DVD burner, use the USB
cable that came with the DVD burner.
When connecting to a BD burner, use a
USB cable with Mini-A(Male) to B(Male)
connectors. JVC’s QAM0852-001 (optional) is
recommended. Refer to page 35 for information
on contacting JVC.
•
Backup All Files
- Playing back the disc on a PC.*
- Playing back the disc using a BD/DVD player
that supports BD-MV and AVCHD.*
* The DVD must first be finalized using the
camcorder’s menu.
Preparation:
Select ! or # mode.
•
Select built-in memory or SD card to copy
from.
•
Connect the camcorder to the BD/DVD
burner.
When using a BD burner, select [CHANGE
REC. MEDIA] and select the disc type.
•
•
Only the BD/DVD created from the
camcorder can be played by operating the
camcorder.
•
When connecting the DVD burner CU-VD50
•
to a TV, you can play back the created disc
without using the camcorder. When playing
back disconnect the USB cable.
1 Select [CREATE FROM ALL] (!
mode) or [SAVE ALL] (# mode).
Connection with a BD/DVD Burner
Preparation:
Turn on the camcorder first, then turn on the
BD/DVD burner.
2 Select the desired setting.
USB Connector
DC Connector
! mode: [ALL SCENES]
•
•
# mode: [ALL IMAGES]
All files in the recording medium are copied.
! mode: [UNSAVED SCENES]
# mode: [UNSAVED IMAGES]
Files that have never been copied are
automatically selected and copied.
AC Adapter
USB Cable
BD/DVD Burner
3 Select [EXECUTE].
To AC Outlet
USB Connector
70 EN
4 Select [YES] or [NO].
To quit the screen
1) Select [QUIT].
2) When [QUIT?] appears, select [YES].
[YES]: Displays the thumbnails by group.
•
[NO]: Displays the thumbnails by date or
•
by playlist.
NOTE
This method can be used to copy video files to
discs in a computer connected to the camcorder.
5 Select [EXECUTE].
The files are copied on the disc. When
•
[COMPLETED] appears, touch OK.
Selecting Files for Backup
Preparation:
When [INSERT NEXT DISC PRESS
•
[STOP] TO EXIT CREATE] appears,
change the disc. Remaining files are
copied on the second disc.
Select ! or # mode.
•
•
•
•
Select built-in memory or SD card to copy from.
Connect the camcorder to the BD/DVD burner.
When using a BD burner, select [CHANGE REC.
MEDIA] and select the disc type.
To cancel copying, select [STOP].
•
Copying Video Files that Have Never
Been Copied
1 Select [SELECT AND CREATE]
(! mode) or [SELECT AND SAVE]
(# mode).
Files that have never been copied to the discs
are automatically selected and copied.
1 Press the < (Power) button for
more than 2 seconds to turn on the
camcorder.
2 Press DIRECT DISC.
2 Select the desired setting.
! mode:
3 Select [YES] or [NO].
[CREATE BY DATE]:
[YES]: Displays the thumbnails by group.
•
•
Files are sorted according to the date on
which they were recorded. Relevant files are
displayed in a list. Select the recording date.
[NO]: Displays the thumbnails by date or
•
by playlist.
[CREATE BY EVENT]:
Files are sorted according to event. Relevant
files are displayed in a list.
•
4 Select [EXECUTE].
Select the event.
[CREATE BY PLAYLIST]:
•
Select the desired playlist from the list of
playlists. The selected playlists are displayed
in a list.
The files are copied on the disc. When
[COMPLETED] appears, touch OK.
When [INSERT NEXT DISC PRESS
[STOP] TO EXIT CREATE] appears,
change the disc. Remaining files are
copied on the second disc.
•
1) Select the desired list.
2) Select the insertion point. To select other
lists, repeat this process.
•
3) Select [SAVE].
To cancel the disc creation, select
[CANCEL].
•
EN 71
Copying Files (Continued)
[SELECT FROM SCENES]:
•
To play back the created disc in the
BD/DVD burner using the camcorder
1) Connect the camcorder to the BD/DVD
burner.
2) Turn on the camcorder first, then turn on
the BD/DVD burner.
Select files individually.
1) Select the desired file. To select other
files, repeat this process.
2) Select [SAVE].
# mode:
3) Insert the disc.
4) Select [PLAYBACK].
[SAVE BY DATE]:
•
Files are sorted according to the date on
which they were recorded. Relevant files are
displayed in a list. Select the recording date.
5) Select the desired folder. (# mode)
6) Select the desired file.
To return to the previous screen, select
[SELECT FROM IMAGES]:
Select files individually.
•
.
@
1) Select the desired file. To select other
files, repeat this process.
2) Select [SAVE].
Digest Playback
If you create a DVD using a DVD burner
CU-VD50/CU-VD30, you can view a few
seconds from the beginning of each video
(digest) in the created DVD.
3 Select [YES] or [NO].
[YES]: Displays the thumbnails by group.
•
[NO]: Displays the thumbnails by date or
by playlist.
•
1 Load the created DVD on the DVD
player.
4 Select [EXECUTE].
2 On the TV, select [DIGEST
The files are copied on the disc. When
PLAYBACK].*
•
[COMPLETED] appears, touch OK.
When [INSERT NEXT DISC PRESS
•
[STOP] TO EXIT CREATE] appears,
change the disc. Remaining files are
copied on the second disc.
To cancel copying, select [STOP].
•
You can view the previous or next page by
selecting £ / ¤.
To quit the screen
1) Select [QUIT].
2) When [QUIT?] appears, select [YES].
* The screen does not appear on the
camcorder.
3 The digest is played back
NOTE
continuously.
In case of [CREATE BY PLAYLIST], date/time
on the file information display shows the
date of copying the file, instead of the actual
recording date.
To return to normal playback/the index
menu
1) Press the top menu button on the remote
control of the DVD device during the
digest playback.
To finalize the disc after copy is finished
1) Connect the camcorder to the BD/DVD
burner.
2) Turn on the camcorder.
3) Select [FINALIZE].
2) Select the desired item.
NOTE
4) Select [EXECUTE].
5) When [COMPLETED] appears, select
[OK].
“Digest Playback” menu is not available when
DVD is burned using the provided Everio
MediaBrowser software.
In some cases, parts of video other than the
beginning may be played back.
•
To check whether the disc was created
properly
On the screen as in step 1, select
[PLAYBACK].
•
Some video may not be played back at all.
•
72 EN
NOTE
Using a USB External Hard Disk Drive
Refer also to the optional USB external hard
disk drive’s instruction manual.
•
•
You can copy video and still image files to
a USB external hard disk drive from the
camcorder.You can also play the files in
the USB external hard disk drive using the
camcorder’s menu.
When connecting to a Seagate’s FreeAgent™
Desk series product, use a USB cable with
Mini-A(Male) to Mini-B(Male) connectors. JVC’s
QAM0852-001 (optional) is recommended.
Refer to page 35 for information on contacting
JVC.
When connecting to a Design by Neil
Poulton series product, use a USB cable with
Mini-A(Male) to B(Male) connectors. JVC’s
QAM0852-001 (optional) is recommended.
Refer to page 35 for information on contacting
JVC.
Connection with a USB External Hard
Disk Drive
•
Preparation:
Turn on the camcorder first, then turn on the
USB external hard disk drive.
USB Connector
DC Connector
Backup All Files
Preparation:
Select ! or # mode.
•
•
•
Select built-in memory or SD card to copy from.
Connect the camcorder to the USB external
hard disk drive.
1 Select the desired setting.
! mode: [ALL SCENES]
•
•
AC Adapter
# mode: [ALL IMAGES]
Mini-A (Male)
– USB-A (Female)
All files in the recording medium are
copied.
! mode: [UNSAVED SCENES]
# mode: [UNSAVED IMAGES]
Files that have never been copied are
automatically selected and copied.
USB Cable
2 Select [OK].
USB-A (Male)
– Mini-B (Male)
To AC Outlet
The files are copied on the disc. When
[COMPLETED] appears, touch OK.
To cancel copying, select [STOP].
•
•
USB Connector
USB External Hard
Disk Drive
EN 73
Copying Files (Continued)
To delete the files in the USB external
hard disk drive
On the screen as in step 1, select
[DELETE].
When copying files or playing back discs
Copying may take time. (For example,
•
copying 1 hour video in XP mode takes
about 20 minutes.)
Avoid the following operations during copying
and playing back.
- Turning off the camcorder or the USB
external hard disk drive.
- Disconnecting the USB cable.
Files in the USB external hard disk drive
cannot be copied back to the camcorder.
Files deleted from the camcorder cannot
be written to a disc using a BD/DVD burner,
even if they have been copied in the USB
external hard disk drive.
Sound or video may be interrupted during
playback.
•
To play back the files in the USB external
hard disk drive
1) On the screen as in step 1, select
[PLAYBACK].
2) Select the desired folder.
3) Select the desired file.
To return to the previous screen, select
•
•
.
@
To format the USB external hard disk
drive
On the screen as in step 1, select
[FORMAT].
•
When connecting a USB external hard
disk drive to the camcorder
When connecting a USB external hard
disk drive to a PC
Do not connect a USB hub between the
camcorder and the USB external hard disk
drive.
Do not format the USB external hard disk
•
•
drive using the PC. If you did, format again
using the camcorder. (All the data in the USB
external hard disk drive will be erased.)
Disconnect the USB external hard disk drive
•
when using other USB devices such as BD/
DVD burner or another USB external hard
disk drive.
Avoid the following operations using the PC.
- Deleting files or folders in the USB external
hard disk drive.
•
Format the USB external hard disk drive
when connecting it to the camcorder for the
first time. (All data is deleted.)
- Moving files or folders in the USB external
hard disk drive.
- Changing the name of files or folders in the
USB external hard disk drive.
These operations make the data impossible
to be played back using the camcorder’s
menu.
•
When you use the PC to edit the data in the
•
USB external hard disk drive, copy the data
to the PC before editing. Editing the data
in the USB external hard disk drive directly
from the PC makes the data impossible to be
played back using the camcorder’s menu.
NOTE
Refer to the help of the provided Everio
MediaBrowser software when you use the PC
to operate the data copied from the camcorder
in the USB external hard disk drive directly.
74 EN
Uploading Files to Websites
6 Select [CAPTURE TRIMMED FILE].
Upload Trimming
You can select the necessary part of the
video and save it as a new video file ready for
uploading.
Preparation:
To set the start/end point again, select
[REDEFINE AREA].
Select ! mode.
•
Select the playback mode.
•
1 Touch MENU.
7 Select [YES].
When copying is finished, the copied file is
added to the index screen.
2 Select [UPLOAD SETTINGS].
To quit the screen
Select [QUIT].
3 Select the desired file.
4 Select [SET] at the start point.
Use these controls to locate
the starting point.
5 Select [SET] at the end point.
The duration between the start point
and the end point cannot be longer than
•
10 minutes.
To cancel the start point setting, select
[CANCEL].
•
EN 75
Operating in Conjunction with TV via HDMI
Operation method 1
Connecting the camcorder to an HDMI-CEC-
enabled TV using the HDMI cable allows you
to utilize the following convenient functions.
HDMI-CEC (Consumer Electronics Control)
is an industry standard that enables
•
interoperability between HDMI-CEC
compliant devices that are connected via
HDMI cables.
TV turns on
! Turn on the
camcorder.
# Select the playback
mode.
$ Connect the HDMI
cable.
automatically and
switches to HDMI
input mode when the
camcorder is turned
on.
NOTE
Not all HDMI-control devices comply with
•
the HDMI-CEC standard. The HDMI control
function of the camcorder will not work when
connected to these devices.
Operation method 2
The camcorder is not guaranteed to operate
with all HDMI-CEC-enabled devices.
Some TVs can operate the HDMI-CEC
functions of the camcorder using the TV’s
remote control.
Depending on the specifications of each
HDMI-CEC-enabled device, some functions
may not work with the camcorder. (For
details, refer to the instruction manual of your
TV.)
•
•
Turn off the TV.
The camcorder turns
off automatically.
•
Operation method 3
Depending on the TV connected, the display
language of the camcorder will automatically
switch to the language that is used for the TV
when the camcorder is turned on.
•
Unintended operations may occur with some
connected devices. In these cases, set
[HDMI CONTROL] to [OFF]. (Z p. 84)
•
(This is applicable only if the camcorder
supports the language selected for the TV.)
To use the camcorder with a language that
differs from the display language of the TV,
set [HDMI CONTROL] to [OFF]. (Z p. 84)
Preparation:
Connect an HDMI cable between the
camcorder and the TV. (Z p. 24)
Turn on the TV and set the HDMI-CEC
related setting to on. (For details, refer to the
instruction manual of the TV.)
Turn on the camcorder and set [HDMI
•
•
NOTE
The display language of the TV will not
•
switch automatically, even if the display
language of the camcorder is changed.
These functions may not work correctly when
devices such as amplifier and selector are
connected. Set [HDMI CONTROL] to [OFF].
If HDMI-CEC does not work properly, turn off
and on the camcorder again.
•
CONTROL] to [ON]. (Z p. 84)
•
•
76 EN
FURTHER INFORMATION
Changing the Menu Settings
To return to the previous screen
Select @.
1 Touch MENU.
To quit the screen
Select [QUIT].
2 Select the desired menu.
3 Select the desired setting.
Mode
! #
#
Menus
MANUAL SETTING
FLASH
Settings: [ ] = Factory-preset
See page 49. (In the manual recording mode only)
See page 21.
See page 52.
!
REGISTER EVENT
[OFF] / 2SEC / 10SEC / FACE DETECTION
FACE DETECTION
The camcorder checks the number of faces in the
monitor and starts countdown when another face is
detected.
z SELF-TIMER
Starts recording when the set
time elapses after SNAPSHOT
is pressed.
NOTE
#
[2SEC] is for reducing camera shake as a still image is
taken 2 seconds after SNAPSHOT is pressed.
•
You can confirm the countdown on the camcorder
screen.
•
It is recommended to attach the camcorder to a tripod
and use this function to prevent the vibration after
•
SNAPSHOT is pressed.
EN 77
Changing the Menu Settings (Continued)
Mode
Menus
Settings: [ ] = Factory-preset
UXP: Extra High quality
It is recommended to use UXP mode when you
will copy the video to a BD. Video recorded in UXP
mode cannot be copied to an AVCHD disc without
downgrading the video quality.
[XP]: High quality
SP: Standard quality
EP: For recording for a long time
n VIDEO QUALITY
!
You can record in full high-definition (1920 x 1080i)
videos with any of the video qualities.
Sets the video quality.
NOTE
It is recommended to set UXP or XP mode when
recording scenes with fast moving or with extreme
changing in brightness to avoid noise.
•
Video data recorded in UXP mode cannot be saved by a
DVD burner. Use a BD burner to save them.
•
See page 51.
!
HIGH SPEED RECORDING
[RECORD ONE SHOT]: Records one still image at a
time.
CONTINUOUS SHOOTING:
Records still images continuously while
SNAPSHOT is pressed.
BRACKETING*: Activates the bracket shooting
function. In addition to an image with the exposure
set by the camcorder, four other images are
recorded with exposure values shifted (between
–0.6 EV and +0.6 EV by 0.3 EV).You can select
the image that has a suitable exposure after
shooting.
SHUTTER MODE
8
Records still images
continuously while SNAPSHOT
is pressed.
! #
* # mode only
NOTE
You can set the interval between recording still images
with [CONT. SHOOTING SPEED].
•
Continuous shooting may not work well depending on the
recording medium.
•
The continuous shooting speed will drop if this function is
used repeatedly.
•
78 EN
Mode
Menus
Settings: [ ] = Factory-preset
4:3 mode:
[3456X2592(9M)] / 3072X2304(7M) / 2592X1944(5M) /
1600X1200(1.9M) / 640X480(0.3M)
16:9 mode:
3456X1944(6.7M) / 3072X1728(5.3M) /
y IMAGE SIZE
Selects the image size for still
images.
#
2592X1456(3.8M) / 1920X1080(2M) / 1280X720(0.9M)
n IMAGE QUALITY
[FINE] / STANDARD
#
Sets the image quality.
[10X/OPTICAL] / 15X/DYNAMIC* /
60X/DIGITAL / 200X/DIGITAL
* Dynamic zoom
The combination of optical and digital zoom technology
offers higher zoom ratio than optical zoom without reducing
the quality.
@ ZOOM
!
Sets the maximum zoom ratio.
NOTE
Optical zoom is used up to [10X/OPTICAL]. Digital zoom
is used from more than [10X/OPTICAL] up to the selected
zoom ratio.
[AUTO] / ISO100 / ISO200 / ISO400 / ISO800 /
ISO1600 / ISO3200
8 GAIN
Makes the sensitivity of the
image sensor equivalent to the
ISO of film.
#
! #
!
NOTE
With the [AUTO] setting, the sensitivity of the image sensor
is increased automatically in less ambient light.
OFF: Deactivates the function.
[ON]: Activates the function.
NOTE
q OIS
Complete stabilization may not be possible if hand shake
is excessive, or depending on the shooting conditions.
Compensates for hand shake.
•
Switch off this mode when recording with the camcorder
on a tripod.
•
GAIN UP
[
OFF: Deactivates the function.
Makes the subject appear
bright automatically when you
record in dark places. However,
the overall color tones appear
grayish.
AGC: Electrically brightens the scene in dark place.
[AUTO]: Automatically brightens the scene when it
is dark. (Becomes brighter than [AGC] in some
condition.)
EN 79
Changing the Menu Settings (Continued)
Mode
Menus
Settings: [ ] = Factory-preset
x.v.Color
X
[OFF]: Deactivates the function.
ON: Activates the function.
Records video in the color
range suitable for viewing in an
x.v.Color™ compliant TV.
!
[OFF]: Deactivates the function.
Reduces noise caused by wind. ON: Activates the function.
o WIND CUT
!
4 GRID
[OFF]: Deactivates the function.
ON: Activates the function.
Displays grid lines on the
monitor to help compose the
subject accurately.
! #
See page 48.
! #
!
USER BUTTON SETTING
OFF: Deactivates the function.
[ON]: Activates the function. Do not turn up the volume
more than the red part on the level indicator.
MIC LEVEL
Displays the microphone input
level.
Y
MIC LEVEL SETTING
d
–2 / –1 / [0] / +1 / +2
!
!
Adjusts the microphone
sensitivity.
The larger the number, the higher the sensitivity.
Select this item, and adjust the volume using the touch
sensor.
HEADPHONE VOL. ADJ.
Adjusts the headphone volume
during recording.
e
NOTE
During playback, adjust the headphone volume using the
zoom lever.
80 EN
Menus
Settings: [ ] = Factory-preset
Select [DISPLAY SETTINGS], then select sub-menus.
DISPLAY SETTINGS
LANGUAGE
[ENGLISH]
See page 17.
9
Sets the display language.
CLOCK ADJUST
:
See page 16.
Sets the time.
DATE STYLE:
[month.day.year] / year.month.day / day.month.year
TIME:
24h / [12h]
DATE DISPLAY STYLE
;
Sets the date and time display
format.
MONITOR BRIGHT
B
Adjusts the brightness of the display by using the touch
sensor.
Sets the brightness of the LCD
monitor.
BRIGHTER: Brightens the backlight on the monitor
regardless of the surrounding conditions.
STANDARD: Select this when saving the battery life.
[AUTO]: The brightness will automatically be set
to [BRIGHTER] when using outdoors and to
[STANDARD] when using indoors (when using the
battery pack).
MONITOR BACKLIGHT
C
Enables you to adjust the brightness
of backlight on the monitor.
FOCUS ASSIST COLOR
When this function is used, the
outline of the focused object is
displayed in the selected color.
RED / GREEN / [BLUE]
EN 81
Changing the Menu Settings (Continued)
Menus
Settings: [ ] = Factory-preset
Select [BASIC SETTINGS], then select sub-menus.
Y BASIC SETTINGS
With each setting, continuous recording is performed at the
following speed:
HIGH SPEED: 6 frames in 0.4 seconds at 15 frames per
second. (
MEDIUM SPEED: 6 frames in 0.9 seconds at 7 frames per
second. (
[LOW SPEED]: 2 frames per second while SNAPSHOT is
pressed. (
)
@ CONT. SHOOTING SPEED
Sets the interval for continuous
shooting.
)
)
NOTE
The continuous shooting speed will drop if this function is used
repeatedly.
OFF: Deactivates the function.
[ON]: Activates the function.
[ DEMO MODE
Introduces special features of
the camcorder when there is no
operation for about 3 minutes during
recording mode.
NOTE
The demonstration only works when the AC adapter is
connected, not with the battery pack.
•
If an SD card is in the camcorder, demonstration will not take
place even if this mode is set to [ON].
•
OFF: Disables the function.
[ON]: Activates the function.
AUTO POWER OFF
(
If the camcorder is not operated for
5 minutes while the power is on,
it turns itself off automatically to
conserve power.
To turn the camcorder on again, close the LCD monitor
and open it again when using the battery pack. When
using the AC adapter, perform any operation such as
zooming.
OFF: Turns off the operation sound.
[ON]: The melody sounds when operations are performed.
\ OPERATION SOUND
Turns on/off the operation sound.
RECORD BUTTON
Enables the recording button [REC]
on the LCD monitor.
OFF: Deactivates the function.
[ON]: Activates the function.
OFF: Deactivates the function.
QUICK RESTART
`
[ON]: If the LCD monitor is opened again within 5 minutes,
the camcorder starts quickly. The power consumption
used for the 5 minute period after the LCD monitor is
closed is approximately 1/3 that used during recording.
This enables you to save more power than leaving the
power on.
Enables the camcorder to start
up quickly when you turn off the
camcorder and then on again within
5 minutes by closing and opening
the LCD monitor.
82 EN
Menus
Settings: [ ] = Factory-preset
] REMOTE
OFF: Does not receive the signal from the remote control.
[ON]: Enables operation with the remote control.
Turns on/off reception of the
operation signal from the remote
control.
OFF: Makes created DVDs recordable (not playable on
device other than the camcorder).
[ON]: Finalizes created DVDs so that they can be played
back on DVD burner.
NOTE
AUTO FINALIZE
_
Sets the DVD to a readable state.
When you play back a DVD created when [OFF] is set on a
DVD burner, select [FINALIZE] on the DVD creation screen.
•
(Z p. 72)
When you create two or more DVDs at the same time, DVDs
other than the last DVD are finalized automatically even if the
setting is [OFF].
•
YES: Performs this function.
[NO]: Cancels this function.
UPDATE
Updates and improves the system
software.
NOTE
Information about obtaining system update will be made
available on the JVC’s web site.
Z FACTORY PRESET
Returns all the camcorder settings to
their default values.
YES: Performs this function.
[NO]: Returns to the menu screen without executing reset.
EN 83
Changing the Menu Settings (Continued)
Menus
Settings: [ ] = Factory-preset
Select [CONNECTION SETTINGS], then select sub-menus.
CONNECTION SETTINGS
DISPLAY ON TV
%
[OFF]: Does not display on TV.
ON: Displays on TV.
Displays camcorder’s on-screen
display on a TV screen.
VIDEO OUTPUT
R
Sets the aspect (16:9/4:3) to the
screen of the connected television
when outputting videos from the AV
connector.
4:3 / [16:9]
COMPONENT OUTPUT
S
[480i]: Outputs at 480i.
1080i: Outputs at 1080i.
Sets the definition of the video
output from the COMPONENT
connector.
[AUTO 1]: It is recommended to select [AUTO 1] usually.
AUTO 2: Select when the video is not projected in
[AUTO 1] correctly.
480p: Select when the video is not projected in [AUTO 2]
HDMI OUTPUT
T
correctly.
Sets the definition of the video output
from the HDMI mini connector.
NOTE
When connecting to a 1080p compatible TV, set [HDMI
OUTPUT] to [AUTO 1]. When this is set, “1080P” appears at the
top of the LCD monitor.*
* Playback mode only
HDMI CONTROL
Selects whether you use the linked
operations with the TV, when you
connect the TV using the HDMI mini
connector.
OFF: Turns off the linked operations.
[ON]: Turns on the linked operations.
84 EN
Menus
Settings: [ ] = Factory-preset
Select [MEDIA SETTINGS], then select sub-menus.
MEDIA SETTINGS
REC MEDIA FOR IMAGE
Sets the recording medium for still
images.
[BUILT-IN MEMORY] / SD CARD
REC MEDIA FOR VIDEO
Sets the recording medium for video.
[BUILT-IN MEMORY] / SD CARD
[FILE]: Initializes all files in the built-in memory.
FILE + MANAGEMENT NO:
Initializes all files and management numbers in the
built-in memory.
FORMAT BUILT-IN MEM.
Ensures stable speeds and
operation when accessing the built-in
memory.
NOTE
Be aware that all files and data including protected files will be
erased by the formatting process.
[FILE]: Initializes all files in the SD card.
FILE + MANAGEMENT NO:
FORMAT SD CARD
,
You have to format newly purchased
SD cards with this camcorder before
using them.
Initializes all files and management numbers in the SD
card.
This will also ensure stable speeds
and operation when accessing the
SD card.
NOTE
Be aware that all files and data including protected files will be
erased by the formatting process.
ERASE BUILT-IN MEM.
YES: Performs this function. Select [OK] when completed.
[NO]: Cancels this function.
When you dispose of the camcorder,
perform this to make it difficult to
recover data in the built-in memory.
EN 85
Troubleshooting
Before requesting service, consult the
following chart. If the solutions indicated in the
chart do not solve the problem, consult your
nearest JVC dealer or JVC service center for
instructions.
Refer also to the FAQ of new products on
JVC’s website.
The following phenomena are not
malfunctions.
The camcorder heats up when it is used for a
•
long time.
The battery heats up during charging.
When playing back a video, the image stops
momentarily or the sound is interrupted at
junctions between scenes.
•
•
LCD monitor momentarily become red or
black when sunlight is recorded.
•
Black spots, or red, green, or blue spots
appear on the LCD monitor.
•
(The LCD monitor contains 99.99% effective
pixels, but 0.01% or fewer pixels may be
ineffective.)
Trouble
Action
Connect the AC adapter correctly.
Recharge the battery pack.
•
•
•
No power is supplied.
When the camcorder has warmed up after being cold, the
camcorder may switch itself off to check it is operating correctly.
Turn on the camcorder again to start using it.
After the low
temperature message
is displayed, the power
turns off when the
camcorder warms up.
If you connect to a TV compatible with HDMI-CEC with an HDMI
cable (optional) and turn off the power on the TV, the power on
the camcorder also turns off. If you are not using HDMI-CEC, set
[HDMI CONTROL] to [OFF].
•
The power was turned
off accidentally.
[QUICK RESTART] is set to [ON].
The battery is being charged.
The power/charge lamp
blinks when the LCD
monitor is closed.
•
•
Fully charge the battery pack, run it down, and then recharge it
again.
If the camcorder is used for long periods of time in high or low
temperatures, or if the battery pack is repeatedly charged, the
amount of remaining battery may not be displayed correctly.
•
The remaining battery
display is not correct.
•
The LCD monitor may be difficult to see if used in bright areas
such as under direct sunlight.
The LCD monitor is
difficult to see.
•
86 EN
Trouble
Action
Slide the mode switch to select the desired mode (! or #).
Recording cannot be
performed.
•
•
•
Such phenomenon occurs when shooting a subject illuminated by
bright light. This is not a malfunction.
Vertical lines appear on
recorded images.
If the camcorder temperature increases, REC flashes in the
LCD monitor and recording stops automatically to protect the
built-in memory. Turn off the camcorder, wait for a while, and start
recording again.
Move away from a place where the camcorder is affected by
excessive sound or vibration (such as a concert hall).
A malfunction may have occured in the built-in memory of
the camcorder. In this case, record to an SD card. Insert a
commercially available SD card, and set each of the [REC MEDIA
FOR VIDEO] and [REC MEDIA FOR IMAGE] to [SD CARD].
Recording stops automatically after 12 hours of continuous
recording.
•
•
Recording stops by
itself.
•
Use backlight compensation.
•
•
•
•
Set [GAIN UP] to [AGC] or [AUTO].
Use [NIGHT] from scene select.
Set the brightness to the [+] side.
The recorded subject is
too dark.
Set the backlight compensation to [OFF] if it is being used.
Set the brightness to the [–] side.
The recorded subject is
too bright.
•
•
Change [ZOOM] to [60X/DIGITAL] or [200X/DIGITAL].
Digital zoom is not available in the still image recording mode.
Digital zoom does not
work.
•
•
Wipe the lens with lens cleaning cloth.
If you are recording in a dark place or a subject that has no
contrast between dark and light, adjust the focus manually.
•
The focus is not
adjusted automatically.
•
Set [WB] in [MANUAL SETTING] appropriately to the light source.
Select [MWB] in [WB] while holding a sheet of plain white paper
in front of the camcorder so that the white paper fills the screen.
Keep touching OK until the B indicator appears.
•
•
The color looks strange.
(Too bluish, too reddish,
etc.)
This cannot be used if [SEPIA] or [MONOTONE] are selected as
•
•
White balance setting
cannot be activated.
effects.
Do not use [TWILIGHT], [FIREWORKS], or [SUNSET] from scene
select.
The continuous shooting speed will drop after continuous shots.
Continuous shooting speed may drop depending on the recording
media or under certain recording conditions.
•
•
The continuous shooting
speed is slow.
This occurs when there is a bright light source near the
camcorder. This is not a malfunction. Change the direction of the
camcorder to prevent the light source comes into view.
Band of bright light
appears on the LCD
monitor.
•
Record videos with high quality mode, such as UXP or XP mode.
Mosaic-type noise
occurs when recording
scenes with fast
•
moving or with extreme
changing in brightness.
EN 87
Troubleshooting (Continued)
Trouble
Action
Sometimes playback is interrupted at the connecting section
between two scenes. This is not a malfunction.
Sound or video are
interrupted.
•
•
Select [PLAYBACK OTHER FILE] then search the video on
the index screen. (Video files that have damaged management
information can be played back.)
Cancel group display and date search functions.
Change the setting in [REC MEDIA FOR VIDEO] or [REC MEDIA
FOR IMAGE]. (Files on other media are not displayed.)
Cannot find a recorded
video.
•
•
The following functions cannot be used for a backup BD/DVD.
When playing back video
- Search index by date
- Playback effects
When playing back still image
Some functions cannot
be used when playing
back a backup BD/DVD
through a BD/DVD
burner connected to the
camcorder.
•
- Playback effects
When recording the white balance was not correctly adjusted.
When the video was recorded with x.v.Color™ set to [ON], change
the setting as desired on TV.
•
•
The color of images
looks strange.
Set [EFFECT] to [OFF].
•
•
If there are many files (such as video) in the camcorder, it takes
time for the camcorder to respond. It is recommended that you
copy all files from the camcorder onto your computer, and erase
the files from the camcorder.
The camcorder operates
slowly when switching
between video mode
and still image mode,
or when switching the
power on or off.
Check the remaining battery pack charge.
•
•
(When the battery pack is fully charged, the lamp does not flash.)
When recharging in either a hot or cold environment, ensure that
battery is being charged within the permitted temperature range.
(If the battery pack is being recharged outside the permitted
temperature range, recharging may stop to protect the battery
pack.)
The lamp does not flash
during battery pack
charging.
Replace the battery.
Set [REMOTE] to [ON].
The remote control may not operate outdoors or in places
exposed to strong light.
•
•
•
The remote control does
not work.
When connecting to the HDMI cable, the image or sound may not
appear on the TV properly depending on the TV connected. In
such cases, perform the following operations.
1) Disconnect the HDMI cable and connect it again.
2) Turn off and on the camcorder again.
When connecting to
the HDMI cable, the
image or sound does
not appear on the TV
properly.
•
TVs may operate differently depending on the specifications,
even if they are HDMI-CEC compliant. Therefore, the HDMI-CEC
functions of the camcorder cannot be guaranteed to operate in
combination with all the TVs. In such cases, set [HDMI CONTROL]
to [OFF].
HDMI-CEC functions do
not work properly, and
the TV does not work
in conjunction with the
camcorder.
•
88 EN
Trouble
Action
It may occur when you connect the camcorder to a TV with
different language setting using an HDMI cable.
The language on the
display changed.
•
You need your YouTube™ account to upload files to YouTube™.
Create your account.
Refer to “Q&A”, “Latest Information”, “Download Information”, etc.
in [Click for Latest Product Info] in the help of the provided Everio
MediaBrowser software.
•
•
Cannot upload the file to
YouTube™
Refer to “Q&A”, “Latest Information”, “Download Information”, etc.
in [Click for Latest Product Info] in the help of the provided Everio
MediaBrowser software.
•
Cannot export the file to
iTunes®
If a malfunction occurs in the built-in memory
! Perform [FORMAT BUILT-IN MEM.]. (All data is deleted.)
# If this does not solve the problem, contact the JVC customer service for repairs.
To reset the camcorder when it does not operate normally
! Close the LCD monitor and remove the power supply (battery pack or AC adapter) from the
camcorder, then reattach it.
# Execute [FACTORY PRESET]. (Z p. 83)
Cleaning
Before cleaning, turn off the camcorder and remove the battery pack and AC adapter.
To clean the camcorder
Wipe the camcorder gently with a soft cloth. If the camcorder is particularly dirty, dip the cloth
into diluted mild soap and wring it out well. After wiping with the wet cloth, wipe again with a dry
cloth.
To clean the LCD monitor
Wipe the LCD monitor gently with a soft cloth. Be careful not to damage the LCD monitor.
To clean the lens
Wipe the lens gently with lens cleaning cloth.
NOTE
Avoid using strong cleaning agents such as benzine or alcohol.
Mold may form if the lens is left dirty.
When using a cleaner or chemically treated cloth, refer to the cautions for each product.
•
•
•
EN 89
Warning Indications
Indication
Action
Set the clock. If the message still appears after setting the
clock, the battery for the clock has been depleted. Consult your
nearest JVC dealer.
•
SET DATE/TIME!
Be sure to use JVC battery packs.
COMMUNICATING ERROR
•
Set [REC MEDIA FOR VIDEO] to [BUILT-IN MEMORY].
Replace the SD card. (Files recorded with other devices that
support AVCHD cannot be played back on this camcorder.)
•
•
CANNOT USE IN
VIDEO MODE
Select [OK] and select [YES] to perform formatting.
NOT FORMATTED
•
Check the operating procedure, and perform once again.
Turn off the camcorder, and turn it on again.
FORMAT ERROR!
•
•
DATA DELETION ERROR
Perform formatting. (All data is deleted.)
Turn off the camcorder, and turn it on again.
•
•
ERROR IN BUILT-IN
MEMORY!
Perform formatting. (All data is deleted.)
Remove and re-insert the SD card. (MultiMediaCard cannot be
used.)
Remove any dirt from the SD card terminals.
Insert the SD card before switching the power on.
Turn off the camcorder, and turn it on again.
•
•
MEMORY CARD ERROR!
•
•
•
Turn off the camcorder and turn it on again.
Prevent the camcorder from vibration and shock.
•
•
RECORDING CANCELLED
RECORDING FAILURE
SD card:
Remove and re-insert the SD card. (MultiMediaCard cannot be
used.)
•
Remove any dirt from the SD card terminals.
Insert the SD card before switching the power on.
Built-in memory:
•
•
PLAYBACK FAILED
Do not allow the camcorder to be subject to impact/vibrations.
•
Delete files. Move files to a PC or other devices.
Replace the SD card with a new one.
•
INSUFFICIENT SPACE
•
90 EN
Indication
Action
Select [OK] to restore.
VIDEO MANAGEMENT FILE IS
DAMAGED, RECOVERY IS
REQUIRED TO RECORD/PLAYBACK,
RECOVER?
•
•
Use files recorded with the camcorder. (Files recorded with other
device may not be played back.)
UNSUPPORTED FILE!
Switch off the [PROTECT/CANCEL] function in the MENU.
THIS FILE IS PROTECTED
NUMBER OF FOLDERS OVERFLOW
•
•
Replace the backup destination with another disc.
Move the files or folders to a PC or other devices, and then
format the built-in memory of the camcorder or the SD card.
Select [FILE + MANAGEMENT NO] in [FORMAT BUILT-IN
MEM.] or [FORMAT SD CARD].
•
•
UPPER LIMIT OF RECORDABLE
MANAGEMENT NUMBERS
HAS BEEN REACHED
SCENE QUANTITY
LIMIT EXCEEDED
When creating a disc, reduce the number of playlists to be
saved.
Reduce the number of the playlist to 99 files or less.
•
•
PLAYLIST QUANTITY
LIMIT EXCEEDED
Turn on the power of the connected USB device.
Connect the AC adapter to the BD/DVD burner.
POWER IS OFF, OR USB
DEVICE IS UNSUPPORTED
•
•
Replace the disc in the BD/DVD burner with another disc.
Replace the disc in the BD/DVD burner with another disc.
Slide the mode switch to select the desired mode (! or #).
USED DVD-R DISC
FINALIZATION FAILED
NO FILES
•
•
•
EN 91
JVC Software License Agreement
JVC SOFTWARE LICENSE AGREEMENT
4 LIMITED WARRANTY
JVC warrants that any media in which the
Program is embodied are free from any
defects in materials and workmanship
for a period of thirty (30) days from the
date of Your purchasing any our products
accompanying the Program. JVC’s entire
liability and your exclusive remedy in
connection with the Program shall be
replacement of such defective media.
EXCEPT FOR THE EXPRESS WARRANTIES
STATED HEREIN AND TO THE EXTENT
PERMITTED BY APPLICABLE LAW, JVC
AND ITS LICENSORS DISCLAIM ANY
OTHER WARRANTIES, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT
LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE IN REGARD TO
THE PROGRAM AND THE ACCOMPANYING
PRINTED MATERIALS. SHOULD THERE
BE ANY PROBLEM ARISING FROM OR
CAUSED BY THE PROGRAM, YOU SHOULD
SETTLE ALL SUCH PROBLEM AT YOUR
OWN COST AND EXPENSE.
IMPORTANT
TO CUSTOMERS: PLEASE MAKE SURE
TO READ THIS CAREFULLY BEFORE
INSTALLING OR USING THE SOFTWARE
PROGRAM NAMED “DIGITAL PHOTO
NAVIGATOR” (“Program”) ON YOUR PC.
The right to use the Program is granted by
Victor Company of Japan, Limited (“JVC”) to
You only on the condition that You agree to the
following.
Should You not agree to the terms hereof,
You may not install or use the Program.
HOWEVER, INSTALLING OR USING THE
PROGRAM INDICATES YOUR ACCEPTANCE
OF THESE TERMS AND CONDITIONS.
1 COPYRIGHT; OWNERSHIP
You acknowledge that all copyrights and other
intellectual property rights in the Program are
owned by JVC and its licensor, and remain
vested in JVC and such licensor. The Program
is protected under the copyright law of Japan
and other countries, and related Conventions.
2 GRANT OF LICENSE
(1) Subject to the conditions of this Agreement,
JVC grants to You a non-exclusive right to
use the Program.You may install and use the
Program on a HDD or other storage devices
incorporated in Your PC.
5 LIMITED LIABILITY
TO THE EXTENT PERMITTED BY
APPLICABLE LAW, IN NO EVENT
SHALL JVC AND ITS LICENSORS BE
LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL
DAMAGES WHATSOEVER, REGARDLESS
OF THE FORM OF ACTION WHETHER
IN CONTRACT, TORT OR OTHERWISE
ARISING OUT OF OR IN CONNECTION
WITH THE USE OF OR INABILITY TO USE
THE PROGRAM, EVEN IF JVC HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.YOU WILL INDEMNIFY AND
HOLD HARMLESS JVC FROM ANY LOSS,
LIABILITY OR COST ARISING OUT OF OR
IN ANY WAY CONNECTED TO CLAIMS
FROM ANY THIRD PARTY RELATING TO
THE USE OF THE PROGRAM.
(2) You may make one (1) copy of the
Program solely for your personal backup or
archival purposes.
3 RESTRICTION ON THE PROGRAM
(1) You may not reverse engineer, decompile,
disassemble, revise or modify the Program,
except to the extent that expressly
permitted by applicable law.
(2) You may not copy or use the Program, in
whole or in part, other than as expressly
specified in this Agreement.
(3) You have no right to grant a license to
use the Program, and may not distribute,
rent, lease or transfer the Program to any
third party or otherwise let them use the
Program.
92 EN
NOTE
6 TERM
This Agreement will become effective on the
date when You install and use the Program on
Your machine, and continue to be in effect until
the termination under the following provision.
Should You breach any provision of this
Agreement, JVC may terminate this
Agreement without giving any notice to You.
In this event, JVC may claim against You for
any damages caused by Your breach. Should
this Agreement be terminated, You must
immediately destroy the Program stored in
Your machine (including the erasing from any
memory in Your PC), and no longer own such
Program.
If You acquired the Program in Germany, the
provisions of Sections 4 (Limited Warranty)
and 5 (Limited Liability) provided above will be
replaced with those of the German version of
this Agreement.
CAUTION:
Operate this equipment according to the
operating procedures described in this
manual.
•
Use only the provided CD-ROM. Never use
any other CD-ROM to run this software.
•
Do not attempt to modify this software.
Changes or modifications not approved by
JVC could void user’s authority to operate
the equipment.
•
•
7 EXPORT CONTROL
You agree that You will not ship, transfer or
export the Program or underlying information
and technology to any countries to which
Japan and other relevant countries have
initiated an embargo on such goods.
How to handle a CD-ROM
Take care not to soil or scratch the mirror
•
surface (opposite to the printed surface).
Do not write anything or put a sticker on
either the front or back surface. If the CD-
ROM gets dirty, gently wipe it with a soft
cloth outward from the center hole.
8 U.S. GOVERNMENT USER
If You are an agency of the United States of
America (the “Government”), You acknowledge
JVC’s representation that the Program is
a “Commercial Item” as defined in Federal
Acquisition Regulation (FAR) part 2.101 (g)
consisting unpublished “Commercial Computer
Software” as those items are used at FAR part
12.212 and is only licensed to You with the
same use rights JVC grants all commercial
end users pursuant to the terms of this
Agreement.
Do not use conventional disc cleaners or
cleaning spray.
•
Do not bend the CD-ROM or touch its
mirror surface.
•
Do not store your CD-ROM in a dusty, hot
or humid environment. Keep it away from
direct sunlight.
•
You can find the latest information (in
English) on the provided software program
at our world wide web server at http://www.
9 GENERAL
(1) No modification, change, addition, deletion
or other alternation of or to this Agreement
will be valid unless reduced to writing and
signed by an authorized representative of
JVC.
(2) If any part of this Agreement is held
invalid by or in conflict with any law having
jurisdiction over this Agreement, the
remaining provisions will remain in full
force and effect.
(3) This Agreement shall be governed by
and interpreted under the laws of Japan.
The Tokyo District Court has jurisdiction
over all disputes which may arise with
respect to the execution, interpretation and
performance of this Agreement.
Victor Company of Japan, Limited
EN 93
Terms
A
K
Aperture Priority ................................................48
Auto Finalize ......................................................83
Auto Power Off ..................................................82
M
Manual Recording .............................................47
Microphone .......................................................80
Monitor Backlight ...............................................81
Monitor Bright ....................................................81
Moving Files ......................................................69
B
Backlight Compensation ....................................50
BD/DVD Backup ................................................70
BD/DVD Burner .................................................70
Brightness Adjustment ......................................47
C
D
O
P
Component Output ............................................84
Continuous Shooting Speed ..............................82
Copying Files .....................................................69
Operation Sound ...............................................82
Optical Image Stabilizer (OIS) ...........................79
Picture Title .......................................................65
Playlists .............................................................64
Date Display Style .............................................81
Deleting Files ....................................................56
Demo Mode .......................................................82
Digest Playback .................................................72
Display on TV ....................................................84
Dividing Files .....................................................61
DPOF ................................................................67
Q
R
Recording Media for Image ...............................85
Remote Control .................................................83
E
F
Effect .................................................................50
Erase Built-in Memory .......................................85
Event Registration .............................................52
Scene Select .....................................................49
Self-Timer ..........................................................77
Sharpness .........................................................51
Shutter Mode .....................................................78
Face Detection ......................................52, 63, 77
Factory Preset ...................................................83
File Information ..................................................59
File Search ..................................................54, 55
Date Index Screen
Event Screen
Group Index Screen
Flash .................................................................77
Focus Assist ......................................................49
Focus Assist Color ............................................81
Format Built-in Memory .....................................85
Format SD Card ................................................85
T
Tele Macro .........................................................50
Trimming Files ...................................................62
U
Updating Software .............................................83
USB Cable ...................................................70, 73
USB External Hard Disk Drive ..........................73
G
H
Gain ...................................................................79
Gain Up .............................................................79
Grid ...................................................................80
Video Quality .....................................................78
W
HDMI ...........................................................76, 84
Headphone Volume ...........................................80
High Speed Recording ......................................51
Histogram ..........................................................59
White Balance (WB) ..........................................50
Wipe or Fader Effects ........................................53
X
Z
I
x.v.Color ............................................................80
Image Quality ....................................................79
Image Size ........................................................79
Zebra .................................................................51
Zoom .................................................................79
US
© 2009 Victor Company of Japan, Limited
0609FOH-AL-OT
|